1
Download a. commercial freezer, refrigerator general
Transcript
■ MODEL : BASF1/BASF2/BASF3(FREEZER) BASR1/BASR2/BASR3(REFRIGERATOR) BAGR72 (REACH-IN MERCHANDISERS) A. COMMERCIAL FREEZER, REFRIGERATOR GENERAL 1. SPECIFICATION - - - - - - - - - - - - - - - - - - - - - - 2 1) GENERAL 2) MAIN COMPONENTS 2. REFRIGERATION CYCLE - - - - - - - - - - - - - - - - - - - 6 3. FEATURE CHART - - - - - - - - - - - - - - - - - - - - - - - 8 4. WIRING DIAGRAM - - - - - - - - - - - - - - - - - - - - - - 5. REPLACEMENT OF COMPONENTS - - - - - - - - - - - - - - - - - -1 - 16 23 1. SPECIFICATION 1) GENERAL - 1,2Door PRODUCT SOLID DOOR FREEZER SOLID DOOR REFRIGERATOR MODEL BASF1 BASF2 BASR1 BASR2 Capacity (Cu,Ft) 23 49 23 49 Net Capacity (Cu,Ft) 20.8 45.2 20.8 45.2 27.4 55.1 27.4 55.1 23.6 51.4 Exterior Dimension (Including casters) (in) Interior Dimension (Including casters) (in) (W) (D) 31.3 (H) 83.9 (W) 23.6 51.4 (D) 25 (H) 60.8 Net Weight (lbs) 295 499 288 475 Door Type Swing 1EA Swing 2EA Swing 1EA Swing 2EA Door Material Shelves Stainless steel (SUS304) 4EA 8EA Power Voltage AC 115V/60Hz Plug in - Installation NEMA 5-15P 4EA 8EA Amps 8.5A 9.5A 7.5A 7.5A Compressor 1/2HP 3/4HP 3/8Hp 3/8HP Refrigerant R404a (12.0 oz) R404a (22.2 oz) R134a (8.5 oz) R134a (11.3 oz) Range of Temperature Below 0℉ 32 ~ 40℉ Door auto-close equipment Auto-close for Spring Door stop equipment 120˚ Stop Air suction equipment Air damper Caster 4in × 4EA Condensing unit Sliding Type ◈ Above specifications are subjected to change without prior notice for quality improvement. ◈ The nameplate(includes Serial Number) is located on the upper left of the cabint interior. -2 - 2) MAIN COMPONENTS - 1,2Door PRODUCT MODEL Compressor (Manufacture) SOLID DOOR FREEZER SOLID DOOR REFRIGERATOR BASR1 BASF1 BASF2 CAE2420Z(A) CAJ2432Z(A) BASR2 SK6A1C-H2Y (Samsung-Korea) (Tecumseh-France) (Tecumseh-France) Compressor Capacity LBP 571kcal/h LBP 808kcal/h HBP 1120kcal/h Type of Compressor motor CSIR CSR RSIR Compressor O.L.P MST16AHN GA3PJU00 4TM811XHBZZ-53 Compressor Relay 3ARR12KPF*483 3ARR3*5R* MTRP0052-02 Starting Capacitor 315㎌/160V 315㎌/160V - Running Capacitor - 30㎌/400V - Type of Evaporator Cu pipe + Al fin + Blue color coating Evaporator pipe Dimensions 3/8" Cooling Fan Motor IS3225LTSA, 120V/60Hz Type of Condenser Cu pipe + Al fin Evaporator pipe Dimensions 3/8" Condenser Fan Motor MA7425W1, Drier 120V/60Hz OD 1", XH-9, 1.06oz Temperature Control Thermistor Thermostat (K55-Q5618) Running Indication Digital Display Indication Lamp Interior Temp. Indication Digital Display Circle analog Thermometer Interior Lamp Defrost for evaporator 40W × 1EA Heated defrost (Control of thermistor) Off cycle Defrost sheath heater 450W 670W - - Defrost pan heater 60W 90W - - - - Drain heater 9W Door switch SP201R-7DR, AC125V Power switch SL112A, -3 - AC125V/12A 3) GENERAL - 3Door PRODUCT SOLID DOOR FREEZER SOLID DOOR REFRIGERATOR REACH IN MERCHANDISERS MODEL BASF3 BASR3 BAGR72 Capacity (Cu,Ft) 70 Net Capacity (Cu,Ft) 66.3 Exterior Dimension (Including casters) (in) Interior Dimension (Including casters) (in) (W) 78 (D) 31.3 (H) 83.9 (W) 74.2 (D) 25 (H) 60.8 Net Weight (lbs) 622 Swing 3EA Door Type Door Material 716 609 Stainless steel (SUS304) Glass + Al 12EA Shelves Power Voltage AC115/208-230V 60Hz AC 115V/60Hz Plug in - Installation NEMA 14-20P NEMA 5-15P Amps 9.0A 10.0A 11.9A Compressor 1.1HP 1/2HP 1/2Hp Refrigerant R404a (23.6 oz) R134a (14.1 oz) R134a (17.6 oz) Range of Temperature Below 0℉ 32 ~ 40℉ Door auto-close equipment Auto-close for Spring Door stop equipment 120˚ Stop Air suction equipment Air damper Caster Caster 4in × 6EA Condensing unit Door switch Power(or Lamp) switch Adjust foot 6EA Sliding Type SP201R-7DR, AC125V SL112A, - AC125V/12A ◈ Above specifications are subjected to change without prior notice for quality improvement. ◈ The nameplate(includes Serial Number) is located on the upper left of the cabint interior. -4 - 4) MAIN COMPONENTS - 3Door PRODUCT SOLID DOOR FREEZER SOLID DOOR REFRIGERATOR REACH IN MERCHANDISERS MODEL BASF3 BASR3 BAGR72 CAJ2446Z(H) CAJ4461Y(A) CAJ4476Y(A) Compressor (Manufacture) (Tecumseh-France) (Tecumseh-France) (Tecumseh-France) Compressor Capacity LBP 1219kcal/h HBP 1586kcal/h HBP 1946kcal/h Type of Compressor motor CSR CSIR CSIR Compressor O.L.P MST00AHN GA3SJU81 CRA38014 Compressor Relay 3ARR3*3A* 3ARR18A100B 3ARR3*2M* Starting Capacitor 88㎌/260V 250㎌/160V 250㎌/160V Running Capacitor 15㎌/400V - - Type of Evaporator Cu pipe + Al fin Blue color coating Evaporator pipe Dimensions Cu pipe + Al fin 1/2" Cooling Fan Motor IS3225LTSA, 120V/60Hz Type of Condenser Cu pipe + Al fin Evaporator pipe Dimensions 3/8" Condenser Fan Motor MA7425W1, Drier 120V/60Hz OD 1", XH-9, 1.06oz Temperature Control Thermistor Thermostat (GNF-246L) Running Indication Digital Display - Interior Temp. Indication Digital Display 32W × 2EA Interior Lamp 40W × 2EA (Fluorescent lamp) Ad. Panel Fluorescent Lamp - 32W × 2EA Ballast - 32W(Double)×2EA Ballast Name (Manufacture) - DY232 IS120 (DOYOUNG) Defrost for evaporator Heated defrost (Control of thermistor) Defrost sheath heater 944W - - Defrost pan heater 128W - - Drain heater 9W - - -5 - Off cycle 2. REFRIGERATION CYCLE Mechanical refrigeration is accomplished by continuously circulating, evaporating, and condensing a fixed supply of refrigerant in a closed system. Evaporation occurs at alow temperature and pressure while condensation occurs at high temperature and pressure. Thus it is possible to transfer heat fom an area of low temperature(i.e., refrigerated compartment) to an area of high temperature(i.e., surrounding of refrigerator). CONDENSER CAPILLARY TUBE COMPRSSOR EVAPORATOR THE BASE REFIGERATION CYCLE Beginning the cycle at the evaporator inlet the low pressure liquid expands, absorbs heat (so refrigerator inner-cabinet is cooled), and evaporates, changing to alow pressure gas at the evaporator outlet. The compressor pumps this gas from the evaporator, increases its pressure, and discharges the high pressured- temperature gas to the conenser. The condenser lets high pressured- temperature gas emit the heat(so surrounding of the condenser is warmed) in order to make it condense. The capillary tube prevents high pressured- temperature gas from entering the evaporator in order to lower the pressure in the evaporator and control the flow of refrigerant into the evaporator automatically. Eventually the desired air temperature in regrigerator inner-cabinet is reached, the thermostat (temperature controller) will break the electrical circuit to the compressor motor and stop the compressor. -6 - As the temperature of the air rises, the thermostat(or controller) remakes the electrical circuit. The compressor starts, and cycle continues. The schematic refrigeration(or freezing) cycle of BASF1/BASF2/BASF3/BASR1/BASR2 BASR3/BAGR72 is like below. 3 9 5 MODEL COMPRESSOR BASF1 CAE2420Z(A) BASF2 CAJ2432Z(A) BASF3 CAJ2446Z(H) BASR1/BASR2 SK6A1C-H2Y BASR3 CAJ4461Y(A) BAGR72 CAJ4476Y(A) Heat Exchange 8 10 4 12 11 1 6 2 7 Part Name No. Description Q'ty 1 COMPRESSOR 2 CONDENSER C1220TS-O,H 1 3 EVAPORATOR C1220TS-O,H 1 4 DRIER C1220T-H 1 5 ACCUMULATOR C1220T-1/4H 1 6 DISCHARGE PIPE C1220T-O 1 7 DRIER CONNECT PIPE C1220T-O 1 8 CAPILLARY TUBE C1220T-H 1 9 SUCTION PIPE (INNER-CABINET) C1220T-O 1 10 SUCTION PIPE (COMPRESSOR) C1220T-O 1 11 CHARGE PIPE (COMPRESSOR) C1220T-O 1 12 CHARGE PIPE (DRIER) C1220T-O 1 1 -7 - Remark 3. FEATURE CHART 1) BASF1/BASR1 (1Door) Display panel Thermometer Upper grille NSF (BASR1) Door S/W Power S/W Door handle Door Lower grille Caster (FRONT) -8 - BASF1/BASR1 Lamp cover Cooling Fan Damper(Air) Evaporator Lamp Shelves Door Shelf Pilaster Air-guard (SIDE) -9 - 2) BASF2/BASR2 (2Door) Display panel Upper grille Power S/W Thermometer Door S/W NSF (BASR2) Door handle Door Lower grille Caster (FRONT) -10 - BASF2/BASR2 Lamp cover Cooling Fan Damper(Air) Evaporator Lamp Shelves Door Shelf Pilaster Air-guard Support Shelf Pilaster (SIDE) -11 - 3) BASF3/BASR3 (3Door) Display panel Upper grille Door S/W Power S/W Door handle Door Lower grille Caster (FRONT) -12 - BASF3/BASR3 Lamp cover Cooling Fan Damper(Air) Evaporator Lamp Door Shelves Shelf Pilaster Air-guard Support Shelf Pilaster (SIDE) -13 - 4) BAGR72 (Glass 3Door) AD. Panel Door(Glass) Door handle Lower grille Adjust foot (FRONT) -14 - BAGR72 Evaporator Fan Motor Evaporator Lamp Shelves Shelf Pilaster Door(Glass) Door handle Support Shelf Pilaster (SIDE) -15 - 4. WIRING DIAGRAMS 1) BASF1 White White Gray Black Black LOWER HEATER (6.5W) UPPER HEATER (6.5W) White White White White SIDE (R) HEATER (16W) SIDE (L) HEATER (16W) White Pink White Red Black Black Orange S/C TRANSFORMER DRAIN HEATER(B)-9W M Black M Orange S Red CONDENSER FAN MOTOR C Black Black O.L.P DRAIN HEATER(A)-60W Bi-Metal Black COMPRESSOR Red Pink Red White MAIN PCB Blue Black Black DEFROST HEATER (450W) Red Gray T-SENSOR EVAPORATOR FAN MOTOR White LAMP Gray Black Orange Black M 13P Black White Red POWER RELAY FRONT PCB Blue White 4 Black 3 2 DOOR S/W 1 D-SENSOR Black Black Black POWER S/W Black Black White BLACK WHITE WHITE HEATER BLACK POWER S/W TOP GRILL GRAY RED BLACK 1 2 3 BLACK BLACK WHITE BLACK 3 1 24 3 1 1 WHITE HEATER RED BLACK WHITE DOOR S/W BLACK BLACK ORANGE RED BLUE WHITE GRAY 2 BI-MATAL INNER CASE #18 BLACK 1 2 DRAIN HEATER DEFROST HEATER BLACK 1 2 PAN HEATER RED Housing 2EA RED GRAY WHITE LAMP BLACK 2 WHITE BLACK M BLACK GRAY RED HEATER BLACK 1 1 1 RED GRAY WHITE BLACK BLACK EVAPORATOR FAN MOTOR BLACK 1 3 WHITE 2 L N 1 2 1 BLACK 2 AC115V 60Hz O.L.P C S 1 MAINPCB 5 PINK 1 2 3 4 URT BLUE 13P FRONT PCB M 1 BLACK 2 M 3 RED ORANGE 1 WHITE COMPRESSOR CAE2420Z N Condenser Fan Motor L BLACK TERMINAL BLOCK BLACK WHITE MACHINE ROOM RED WHITE RELAY S/C 4 INNER CASE WHITE -16 - FRONT CASE (UPPER) 2) BASF2 Gray LOWER HEATER (14.5W) White White UPPER HEATER (14.5W) SID E (R) HEATER (16W) Black Gray Black Black Black POST HEATER (14W) White Red White Black White Wh it e White Pink White M TRANSFORMER POST HEATER (14.6W) COMPRESSOR CONDENSER FAN MOTOR Black White M M Red SID E (L) HEATER (16W) S Blue Black C Orange 5 DRAIN HEATER(B)-9W Bi-Metal 4 White White O.L.P 3L R/C White EVAPORATOR FAN MOTOR White M LAMP 1 2N S/C Black Red Black Gray Black Blue Black Red MAIN PCB Orange 4 Black Pink Red White Red 2 Black DRA IN HEATER(A)-90W 3 Black Red 1 Orange DOOR S/W Black Black Red DEFROST HEA TER (670W) 4 13P Black 2 POWER RELAY FRONT PCB Gray 3 D-SENSOR 1 DOOR S/W Black T-SENSOR Black POWER S/W Black White URT BLACK WHITE BLACK BLACK 1 12 3 BLACK DOOR S/W GRAY BLACK GRAY 2431 BLUE DOOR S/W RED 1 2 ORANGE BLACK 2 3 2 M 1 2 1 BLACK 1 3 WHITE AC115V 60Hz RED MACHINE ROOM WHITE 1 2N URT O.L.P 3L 3 2 PINK WHITE 1 3 RED 1 3 5 MAINPCB 1 2 3 4 4P BLUE 4 5 13P C S/C FRONT PCB R/C S ORANGE N 2 Condenser Fan Motor L 1 BLACK N 1 WHITE L RED BLACK WHITE BLACK WHITE TERMINAL BLOCK GRAY BLACK WHITE 2431 BLACK RED BLACK 1 2 BI-MATAL BLACK BLACK 3 DEFROST HEATER GRAY 2 RE D BLACK TOP GRILL 1 1 2 DRAIN HEATER WHITE 1 RED PAN HEATER INNER CASE POWER S/W Housing 2EA LAMP MIDDLE HEATER (2EA) RED BLACK 2 WHITE HEATER HEATER WHITE 1 WHITE BLACK BLACK M 2 WHITE BLACK M BLACK EVAPORATOR FAN MOTOR BLACK WHITE 1 1 1 GRAY GRAY RED WHITE BLACK BLACK BLACK M BLACK WHITE COMPRESSOR CAJ2432Z -17 - INNER CASE FRONT CASE (UPPER) WHITE WHITE BLACK AC115V 3Ø 60Hz RED L N 1 2 3 L N 1 2 3 BLACK 1 HEATER DEFROST HEATER (944W) BI-MATAL (16W) ORANGE BLACK 2 1 BLACK 2 M RED RED 2N 3L 4 5 O.L.P S/C S COMPRESSOR CAJ2446Z MACHINE ROOM -18 BLACK BLACK WHITE WHITE HEATER BLACK BLACK 1 URT HEATER TOP GRILL POWER S/W BLACK RED BLACK RED 432 1 4321 DOOR S/W RED PINK DOOR S/W 2 6 1 4 3 5 C R/C M INNER CASE GRAY GRAY RED BLACK WHITE 4P FRONT PCB 13P 1 3 3 1 5 MAINPCB 1 2 3 4 BLUE FRONT CASE (UPPER) WH ITE B LAC K BLACK POST HEA TER (14 .6W+14W ) BLACK White White White W HI TE (16W) B LAC K M POST HEA TER (14 .6W+14W ) COMPRESSOR R ED TRANSFORMER M BL ACK S BL ACK C Gray POST HEATER (14W) White LOWER HEATER (21.5W) SIDE (R) HEATER (16W) UPPER HEATER (21.5W) POST HEATER (14W) White White POST HEATER (14.6W) White White POST HEATER (14.6W) Black Black Black Black Black Black Orange SIDE (L) HEATER (16W) DRAIN HEATER(B)-9W Orange White Black Black Gray Gray Black Gray POWER S/W Black Black Black DRAIN HEATER(A)-138W Bi-Metal Red DEFROST HEATER (944W) R/C GR AY RED R ED CONDENSER FAN MOTOR Black Red B LACK S/C GRA Y RED RED Red O.L.P BLA CK WH ITE (9W) DRAIN 5 RE D HEATER 4 WH ITE Housing 2EA BLU E INNER CASE T-SENSOR D-SENSOR DOOR S/W Red OR AN GE 2 WHITE 1 (138W) PAN 1 RED (40W) 2N BLA CK LAMP 3L DOOR S/ W LAMP Black 4 3 21 (40W) Red 1 1 B LAC K White White Red RE D 2 13P RE D WHITE WHITE 1 2 3 BLACK Blue B LAC K 1 FRONT PCB 2 WHITE 2 B LAC K WHITE PCB Pink Red White B LA CK M 2 MAIN (21.5 W) Black Black White Orange B LACK WHITE 1 BLACK 1 M 1 1 LAMP 1 EVAPORATOR FAN MOTOR M Blue BLA CK BLACK 2 M M 1 M 2 Red 1 4 3 3 2 1 1 White 4 Red 3 2 DOOR S/W 1 DOOR S/W Red 4 EVAPORATOR FAN MOTOR Red 2 2 Red White Black 3 3 1 G RAY Red 1 Co ndenser Fan Mo tor WHITE (21.5W) GRAY BLACK RED RED Black WHITE WHITE 2 TERMINAL BLOCK (5P) 1 WH ITE BLACK WHITE 3) BASF3 Black POWER RELAY Pink WHITE RED URT WHITE O.L.P Black C LAMP M M EVAPORATOR FAN MOTOR White S M White Red Black White White White White White White LOWER HEATER (6.5W) COMPRESSOR DOOR S/W White 4 SIDE (L) HEATER (16W or 12W) 2 RUNNING INDICATOR 3 CONDENSER FAN MOTOR Black Black 1 UPPER HEATER (6.5W) THERMOSTAT Black White 4 Gray Black Black(or Blue) Black Red 3 Black White SIDE (R) HEATER (16W or 12W) Black(or Blue) Black Black Black 4) BASR1 FRONT CASE (UPPER) WHITE INNER CASE WHITE WHITE BLACK RED BLACK(or Blue) HEATER THERMOSTAT M WHITE BLACK WHITE 2 HEATER BLACK WHITE 1 BLACK RED 4 3 BLACK 12 3 LAMP GRAY RED 1 1 Housing 2EA BLACK BLACK BLACK EVAPORATOR FAN MOTOR RED BLACK RED URT WHITE WHITE BLACK BLACK(or Blue) 1 L N 1 1 1 BLACK 2 C S M AC115V 60Hz BLACK WHITE M COMPRESSOR SK6A1C-H2Y N Condenser Fan Motor L O.L.P 2 TERMINAL BLOCK BLACK WHITE RED MACHINE ROOM WHITE WHITE -19 - 110REC RUNNING INDICATOR 24 3 1 DOOR S/W TOP GRILL M Black EVAPORATOR FAN MOTOR White Gray Gray(or Blue) Black Black White White White M White M LAMP White White Red Red M LOWER HEATER (14.5W) S Black White White 4 SIDE (R) HEATER (16W or 12W) 2 White DOOR S/W UPPER HEATER (14.5W) Red C 3 White 1 O.L.P CONDENSER FAN MOTOR Black Black Gray COMPRESSOR POST HEATER (12.1W) Black DOOR S/W SIDE (L) HEATER (16W or 12W) 4 White 2 RUNNING INDICATOR 3 White THERMOSTAT 1 Gray 4 3 POST HEATER (12.6W) Black Red Black(or Blue) Black White Black Black Black 5) BASR2 FRONT CASE (UPPER) WHITE THERMOSTAT INNER CASE BLACK 1 BLACK WHITE WHITE 2 WHITE BLACK WHITE 1 2 BLACK WHITE POST HEATER GRAY WHITE 1 1 Housing 2EA GRAY LAMP WHITE 1 TOP GRILL 12 3 M BLACK BLACK M HEATER BLACK BLACK RED EVAPORATOR FAN MOTOR HEATER 4 3 B LACK W HITE WHITE BLACK RED BLACK(or Blue) RED GRAY(or Blue) 2 L N 1 2 TERMINAL BLOCK 2 1 2 BLACK RED MACHINE ROOM WHITE O.L.P C S M BLA CK WHITE AC115V 60Hz M COMPRESSOR SK6A1C-H2Y 1 Condenser Fan Motor N 1 L B LACK WHITE WHITE -20 - 24 3 1 DOOR S/W 110REC RUNNING INDICATOR 24 3 1 DOOR S/W BLACK R ED WHITE B LACK URT BLACK WHITE 6) BASR3 Gray BLUE LOWER HEATER (21.5W) SIDE (R) HEATER (12W) Black UPPER HEATER (21.5W) White Black Black POST HEATER (15.5W) White Gray BLUE CONDENSER FAN MOTOR TRANSFORMER White M S/C Red White Red White White M White White M LAMP Red C S EVAPORATOR FAN MOTOR M O.L.P S L 3 Black M 2 POST HEATER (15.5W) Red 1 4 Blue SIDE (L) HEATER (12W) 4 COMPRESSOR White 2 Black Red White MAIN PCB Orange Black Red Earth 3 13P Black White 1 Black Gray Black POWER S/W T-SENSOR 4 POWER RELAY FRONT PCB White 2 Black 3 DOOR S/W 1 Red Red 4 DOOR S/W 2 Black Black Black 3 1 White DOOR S/W Black Black URT BLACK WHITE (12W) 2 3 1 2 3 GRAY WHITE BLACK 2 M 1 BLACK RED WHITE MACHINE ROOM 2 3 L 1 3 RED 1 3 1 4 MAINPCB 5 O.L.P S 1 3 1 2 C 13P S M Earth T-SENSOR FRONT PCB S/C 1 WHITE WHITE 2 4 1 N Condenser Fan Motor N L 2 AC115V 60Hz L BLACK WHITE TERMINAL BLOCK (5P) RED BLACK URT BLACK BLUE ORANGE (12W) RED DOOR S/W WHITE GRAY BLUE 432 1 DOOR S/W INNER CASE WHITE RED (21.5W) DOOR S/W BLACK INNER CASE WHITE COMPRESSOR CAJ4461Y(A)-TECUMSEH -21 - FRONT CASE (UPPER) WHITE BLACK POST HEATER (15.5W) BLACK 4321 BLACK BLAC K GRAY 1 WHITE BLACK BLACK 1 RED POST HEATER (15.5W) 1 2 3 Housing 2EA LAMP (40W) BLACK RED 4 3 2 1 (21.5W) LAMP (40W) WHITE 1 2 WHITE POWER S/W TOP GRILL BLACK M WHITE BLACK WHITE BLACK HEATER BLACK WHITE 1 2 WHITE 1 M RED BLACK EVAPORATOR FAN MOTOR HEATER WHITE BLACK 1 2 WHITE 1 GRAY GRAY RED WHITE BLACK M BLACK BLACK BLACK WHITE WHITE WHITE BLUE BLACK Red Black BLUE BALLAST 32W X 2 BLUE White BLUE M White RED RED URT BLACK WHITE (12W) LAMP S/W WHITE BLACK WHITE BLUE RED RED RED BLUE 1 2 2 1 RED BLUE RED 1 2 3 RED 32W X 2 BLACK 32W X 2 FL LAMP 32W BLACK BLUE 2 BLUE RED RED GRAY BLUE (21.5W) RED FL LAMP 32W 1 WHITE RED 2 2 WHITE 3 1 4 2 BLACK 1 BLUE (12W) URT WHITE 3 L N 1 2 3 TERMINAL BLOCK (5P) BLACK M O.L.P 4 5 C S/C FL LAMP 32W 2 BLUE 1 1 2N 3L BLUE N 1 FL LAMP 32W L 2 Condenser Fan Motor WHITE DOOR HEATER (20W X 3) R/C S M RED BLACK 2 1 BLACK WHITE WHITE WHITE COMPRESSOR CAJ4476Y(A)-TECUMSEH FRONT CASE (UPPER) MACHINE ROOM -22 - POST HEATER (15.5W) BLACK 187REC. WHITE POST HEATER (15.5W) 1 WHITE WHITE HEATER BLACK BLACK 2 M WHITE WHITE M EVAPORATOR FAN MOTOR WHITE 2 WHITE BLACK BLACK 1 (21.5W) M BLACK 1 WHITE WHITE BLACK BLACK WHITE RED WHI TE B LAC K HEATER RED BLACK BLACK BLACK 250REC. THERMOSTAT WHITE BLUE INNER CASE FL LAMP 32W RED FL LAMP 32W FL LAMP 32W FL LAMP 32W RED LOWER HEATER (21.5W) UPPER HEATER (21.5W) SIDE (R) HEATER (12W) RED RED White White White White COMPRESSOR CONDENSER FAN MOTOR AC115V 60Hz BLUE Gray BLUE Black Black Black BALLAST 32W X 2 White M White S White LAMP S/W White R/C POST HEATER (15.5W) EVAPORATOR FAN MOTOR C S/C White 5 POST HEATER (15.5W) M White M 4 SIDE (L) HEATER (12W) M O.L.P 3L DOOR HEATER (20W) 1 2N DOOR HEATER (20W) DOOR HEATER (20W) Black Black Black Black White Black BLUE White THERMOSTAT Black Black 7) BAGR72 5. REPLACEMENT OF COMPONENTS 1) CONDENSING UNIT (BASF2/BASF3/BASR2/BASR2) (BASF1/BASR1) a) Unplug the power cord before service. b) Remove screw securing the lower grille. * Remove screw securing the Disassemble reinforce angle.(BAGR72) (BAGR72) (BASF2/BASF3/BASR2/BASR2) (BASF1/BASR1) c) Separate the compressor harness out of the terminal block. d) Remove screws securing the unit base plate and pull out condensing unit with care. e) Replace the necessary com(BAGR72) ponent. -23 - ※ CAUTION 1. Please pull out or push in the unit base plate carefully to prevent capillary tube, pipes and wires from demaging. 2. It is recommend to arrange wires after you push in the unit base plate. 2) LAMP (BAGR72) Lamp Holder Ad. Panel Frame (R) Cap Lamp Lamp Thin Screw Ad. Panel a) Unplug the power cord before service. b) Remove screw securing the Ad. Panel Frame (R). c) Separate the Ad. Panel. d) Separate the Lamp from the Lamp Holder. e) Separate the Cap Lamp and replace the Lamp with care. -24 - a) Unplug the power cord before Cap Lamp service. b) Separate the Lamp from the Lamp Holder. c) Separate the Lamp Socket and Lamp Base the Cap Lamp. d) Replace the Lamp with care. Lamp Lamp Tube Socket ♠ Lamp Description : AC115V, 32W, F32T8/TL860 -25 - ■ MODEL : BASF1/BASF2/BASF3(FREEZER) BASR1/BASR2/BASR3(REFRIGERATOR) BAGR72 (REACH-IN MERCHANDISERS) B. OPERATION AND ELECTRONIC CONTROLLER FUNCTION 1. OPERATION FOR BASF1, BASF2, BASF3 MODELS - - - - - - - - - B3 1) BASIC OPERATION 2) ELECTRONIC CONTROLLER SETING MODE 3) NORMAL CONTROL PROCESS 4) ERROR CODE 2. OPERATION FOR BASR3 MODEL - - - - - - - - - - - - - - - - - B10 1) BASIC OPERATION 2) ELECTRONIC CONTROLLER SETING MODE 3) NORMAL CONTROL PROCESS 4) ERROR CODE 3. OPERATION FOR BASR1, BASR2, BAGR72 MODELS - - - - - - - - B16 1) BASIC OPERATION 2) DEFROST 3) CONTROL TEMPERATURE 4) LAMP 4. INSTRUCTION FOR RE-HINGING DOOR - - - - - - - - - - - - - B17 - B1 - 1. OPERATION FOR BASF1, BASF2, BASF3 MODELS 1) BASIC OPERATION ① Plug in the power cord and turn on the power switch located on the bottom of the top grille right side. [ The unit should be plugged into a 115V±10%, 60Hz (BASF1, BASF2 models) ] [ The unit should be plugged into a 115V/208~230V, 60Hz (BASF3 model) ] ② Display panel will be lightened for 2 seconds with buzzer then displays cabinet interior temperature (T-sensor) and running conditions. If cabinet interior temperature is higher than 14℉(BASF1, BASF2, BASF3 models), compressor will run without delay, and lower than 14℉(BASF1, BASF2, BASF3 models), compressor will run after 3 minutes. ③ The default OPERATING TEMPERATURE SETTING BASF1, BASF2, BASF3 : Temperature set point (setting mode sign [st]) is –9℉ Temperature differential set point (setting mode sign [di]) is 10℉. (Operating Temperature : -14℉ ~ -4℉) Range of adjustable set point: -22℉ ~ 8℉ ④ Dfrost frequency is controlled by MICOM and the default defrost frequency is 6 hours. ⑤ The light inside the cabinet comes on when the door is opened. The cabinet interior cooling fan has 3 seconds delay when the door is closed. ⑥ If door is opened, door open warnign sign (LED) will turn on. If door is opened more than 30 seconds, the sound alarm beeps 3times, if open more than 60 seconds, the sound alarm beeps 5 times and if open more than 5 minutes, the sound alarm will beep continuously. ⑦ If cabinet interior temperature is higher than 14℉(BASF1, BASF2, BASF3), the panel displays [Hi] and lower than -50℉(BASF1, BASF2, BASF3), the panel displays [Lo]. - B2 - 2) ELECTRONIC CONTROLLER SETTING MODE It displays CABINET TEMPERATURE or CURRENT MODE MANUAL D.F./ VERIFY BUTTON COMPRESSOR ON UP BUTTON MODE / SET MANUAL / VERIFY D.F. RUNNING DISPLAY ON POWER SWITCH DOWN BUTTON DOOR OPENING No MODE/SET BUTTON SSeettttiinngg MMooddee SSiiggnn Setting Mode St Temperature Setting Mode di Temperature Differential Setting Mode dt Defrost Frequency Setting Mode dF Forced Defrost Mode tb Turbo Freeze Mode th Cabinet Temperature Verification Mode Setting Mode Mode Sign How to Setting (FREEZER) 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously 1 Temperature Setting Mode until [St] is displayed. "St" 2. Then press [MODE/SET] to see current temperature set point. 3. To change the set point, press [UP or DOWN] until the desired value is displayed. - B3 - No Setting Mode Mode Sign How to Setting (FREEZER) 4. At the end of the sequence, press [MODE/SET] to set the value. 5. To display the cabinet temperature again, press [UP or DOWN] until [th] is displayed and then press [VERIFY] . ☞ → → MODE/SET → → ☞ ☞ → → ☞ → → "St" → MODE/SET → 1 Temperature Setting Mode ☞ MANUAL/VERIFY D.F ☞ MODE/SET 6. Range of adjustable set point : -22℉ to 8℉ 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [di] is displayed. 2. Then press [MODE/SET] to see current temperature differential. 3. To change the set point, press [UP or DOWN] until the desired value is displayed. 4. At the end of the sequence, press [MODE/SET] to set the value. 5. To display the cabinet temperature again, press [UP or DOWN] until [th] is displayed and then press [VERIFY] . → → MANUAL/VERIFY D.F ☞ → ☞ ☞ → → ☞ → MODE/SET → → ☞ → ☞ → MODE/SET → "di" → 2 Temperature Differential Setting Mode MODE/SET ☞ 6. Range of adjustable set point : 4℉ to 16℉ (The Unit of Setting : 2℉) 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [dt] is displayed. 2. Then press [MODE/SET] to see current defrost frequency. 3 Defrost Frequency Setting Mode "dt" 3. To change the defrost frequency, press [UP or DOWN] until the desired value is displayed. 4. At the end of the sequence, press [MODE/SET] to set the value. 5. To display the cabinet temperature again, press [UP or DOWN] until [th] is displayed and then press [VERIFY] . - B4 - Mode Sign How to Setting (FREEZER) → ☞ → "dt" MANUAL/VERIFY D.F ☞ → → ☞ MODE/SET → 3 Defrost Frequency Setting Mode ☞ → → → ☞ → ☞ → MODE/SET → Setting Mode → No MODE/SET ☞ 6. Range of adjustable defrost frequency : 4Hr to 12Hr (The Unit of frequency : 2Hr) 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [dF] is displayed. 4 Forced Defrost Mode 2. Then press [MANUAL DF] more than 2 seconds to start forced defrost. "dF" ☞ → → MODE/SET ☞ → → ☞ More Than 2 Seconds MANUAL/VERIFY D.F 3. During defrosting, [dF] is displayed instead of the cabinet temperature. 5 Cancelation of Forced Defrost Mode 1. During forced defrost, press [MANUAL DF] more than Flash "dF" ☞ 2 seconds to stop forced defrost. More Than 2 Seconds MANUAL/VERIFY D.F 2. The [dF] will be flash 5 times and then return to normal display mode. 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [tb] is displayed. 6 Turbo Freeze Mode 2. Then press [MODE/SET] more than 2 seconds to start turbo freeze mode. "tb" ☞ → → MODE/SET ☞ → → ☞ More Than 2 Seconds MANUAL/VERIFY D.F 3. During turbo freeze, [tb] is displayed instead of the cabinet temperature. 7 8 Cancelation of Turbo Freeze Mode Cabinet Temperature Verification Mode 1. During turbo freeze, press [MODE/SET] more than Flash "tb" 2 seconds to stop turbo freeze. ☞ More Than 2 Seconds MANUAL/VERIFY D.F 2. The [tb] will be flash 5 times and then return to normal display mode. 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously "th" until [th] is displayed. 2. Then press [MODE/SET] to see F-sensor, D-sensor temperature in turn. - B5 - No Setting Mode Mode Sign How to Setting (FREEZER) ☞ → → MODE/SET → ☞ → ☞ → MODE/SET 3. To check only the F-sensor or D-sensor temperature, press [MODE/SET] 8 Cabinet Temperature Verification Mode again. "th" → ☞ → MODE/SET 4. Press [VERIFY] to see current cabinet temperature. (return to normal display mode) ☞ MANUAL/VERIFY D.F 3) NORMAL CONTROL PROCESS No FUNCTION FUNCTION SPEC (FREEZER) 1. After Power ON, Display panel will be lightened for 2 seconds with buzzer then 1 Initial Operating displays cabinet interior temperature. 2. If cabinet interior temperature is higher than 14℉, compressor will run without delay, and lower than 14℉, compressor will run after 3 minutes. 1. Compressor and condenser fan motor is controlled by T-sensor and MICOM program. displays cabinet interior temperature. 2 Normal Operating 2. Compressor ON/OFF Temperature Compressor ON : Temperature Setting Value ＋ (Temperature Differential Setting Value/2) Compressor OFF : Temperature Setting Value - (Temperature Differential Setting Value/2) ex) st: -9℉, di: 10℉ ⇒ Compressoer ON: -9+(10/2) = -4℉,Compressoer OFF: -9-(10/2) = -14℉ 1. Compressor and cabinet interior cooling fan is running continuously for 120 minutes without control by sensor. 2. It is impossible to set the other modes during Turbo Freeze Mode. 3 Turbo Freeze It is necessary to cancel the Turbo Freeze Mode before setting the other modes. 3. If Defrost Mode become in the Turbo Freeze Mode duration, Defrost Mode will start after the Turbo Freeze Mode finished. 4. Turbo Freeze Mode will be start after Defrost Mode finished not during Defrost Mode. [tb] is displayed from startng the Turbo Freeze Mode. - B6 - No FUNCTION SPEC (FREEZER) FUNCTION 1. Defrost process is like below Process Controlled Part Description Pre-Cool Compressor On Evaporator Fan On Condenser Fan On Defrost Heater Off ① It prevent exceed temperature rise during defrosting, ② Cycle is run continuously until current compressor cut-out temperature reach. ③ Maximum time: 30minutes Compressor Off Evaporator Fan Off Condenser Fan Off Defrost Heater On ① Preprogrammed frequency interval ② If D-sensor is higher than 50℉, defrost heater off ③ Maximum time: 40minutes Pause Compressor Off Evaporator Fan Off Condenser Fan Off Defrost Heater Off 5minutes ① Time: 3minutes Evaporator Fan Delay Compressor On Evaporator Fan Off Condenser Fan On Off Defrost Heater On ① If D-sensor is lower than -4℉, Fan delay terminated ② Maximum time: 10minutes Defrost 4 Defrost 1. Temperature Setting : -9℉, Temperature Differential Setting : 10℉ 5 Default Setting 2. Operating Temperature : -14℉(compressor off) ~ -4℉ (compressor on) 3. Defrost Frequency Setting : 6Hr 6 Setting Back UP 1. In case of unexpected power failure or power off, does not require resetting. 2. The setting is memorized. 1. If cabinet interior temperature is higher than 14℉ the panel displays [Hi], and lower than -50℉ the panel displays [Lo]. 7 Error Display 2. Press [down] button 5 times with pressing and holding [up] button, the Error display mode is activated and it displays errors. 3. When there are more than 2 errors, the errors are displayed alternately. 4. If you press [MODE/SET] button, the error display mode will be finished - B7 - 4) ERROR CODE Error Code Condition C1 During normal mode (not defrost mode), D-sensor sensing is higher than 23℉ and Compressor does not run for 60min after compressor off C2 Entering defrost mode, D-sensor sensing is higher than 50℉ and T-sensor sensing is lower than 14℉ C3 After defrost mode elapsed for 40minutes, D-sensor sensing is lower than 23℉ ● Ambinet Temperature too low (below -5℉) z T-sensor defective 1) Register "C1" 2) Compressor ON:20Minutes 3) Compressor OFF:5Minutes 4) Operate 2),3) three times 5) Operate Normal Mode z D-sensor defective 1) Register "C2" 2) Operate Pre-Cool step : 30Minutes 3) Defrost Heater ON : 20Minutes 4) Operate the rest Defrost Mode z D-sensor defective Defrost heater defective 1) Register "C3" 2) Operate the rest Defrost Mode z Refrigerant leak Control board defective Door not sealing Not enough defrosts Condenser dirty Sensor defective 1) Register "C4" 2) Compressor ON:20Minutes 3) Compressor OFF:5Minutes 4) Operate 2),3) three times 5) Operate Normal Mode z N/A N/A z z C4 T-sensor sensing is more than 18℉ higher than temperature set point for 4hours Additionnal Possible Cause: Too many hot goods loaded!! C- No error code When error occurring, operation Possible Cause z z z z - B8 - 2. OPERATION FOR BASR3 MODEL 1) BASIC OPERATION ① Plug in the power cord and turn on the power switch located on the bottom of the top grille right side. [ The unit should be plugged into a 115V±10%, 60Hz (BASR3)] ② Display panel will be lightened for 2 seconds with buzzer then displays cabinet interior temperature and running conditions. If cabinet interior temperature is higher than 50℉(BASR3), compressor will run without delay, and lower than 50℉ (BASR3), compressor will run after 3 minutes. ③ The default OPERATING TEMPERATURE SETTING BASR3 : Temperature set point (setting mode sign [st]) is 39℉ Temperature differential set point (setting mode sign [di]) is 10℉. (Operating Temperature : 34℉ ~ 44℉) Range of adjustable set point: 25℉ ~ 50℉ ④ Dfrost frequency is controled by MICOM and the default defrost frequency is 6 hours. ⑤ The lignt inside the cabinet comes on when the door is opened. The cabinet interior cooling fan has 3seconds delay when the door is closed. ⑥ If door is opened, door open warnign sign will turn on. If door is opened more than 30 seconds, the sound alarm beeps 2times, if open more than 60 seconds, the sound alarm beeps 5 times and if open more than 5 minutes, the sound alarm will beep continuously. ⑦ If cabinet interior temperature is higher than 68℉(BASR3) the panel displays [Hi] and lower than 14℉(BASR3) the panel displays [Lo]. - B9 - 2) ELECTRONIC CONTROLLER SETTING MODE It displays CABINET TEMPERATURE or CURRENT MODE MANUAL D.F./ VERIFY BUTTON COMPRESSOR ON UP BUTTON MODE / SET MANUAL / VERIFY D.F. RUNNINGSWITCH DISPLAYON POWER DOWN BUTTON DOOR OPENING No MODE/SET BUTTON SSeettttiinngg MMooddee SSiiggnn Setting Mode St Temperature Setting Mode di Temperature Differential Setting Mode dt Defrost Frequency Setting Mode dF Forced Defrost Mode th Cabinet Temperature Verification Mode Setting Mode Mode Sign How to Setting (REFRIGERATOR) 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [St] is displayed. 1 Temperature Setting Mode "St" 2. Then press [MODE/SET] to see current temperature set point. 3. To change the set point, press [UP or DOWN] until the desired value is displayed. 4. At the end of the sequence, press [MODE/SET] to set the value. - B10 - No Setting Mode Mode Sign How to Setting (REFRIGERATOR) 5. To display the cabinet temperature again, press [UP or DOWN] until [th] is displayed and then press [VERIFY] . ☞ → → ☞ → "St" → MODE/SET ☞ → → ☞ → → → MODE/SET → 1 Temperature Setting Mode ☞ MANUAL/VERIFY D.F ☞ MODE/SET 6. Range of adjustable set point : 25℉ to 50℉ 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [di] is displayed. 2. Then press [MODE/SET] to see current temperature differential. 3. To change the set point, press [UP or DOWN] until the desired value is displayed. 4. At the end of the sequence, press [MODE/SET] to set the value. 5. To display the cabinet temperature again, press [UP or DOWN] until [th] is displayed and then press [VERIFY] . → → MANUAL/VERIFY D.F ☞ → ☞ ☞ → → ☞ → MODE/SET → → ☞ → ☞ → MODE/SET → "di" → 2 Temperature Differential Setting Mode MODE/SET ☞ 6. Range of adjustable set point : 6℉ to 16℉ (The Unit of Setting : 2℉) 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [dt] is displayed. 2. Then press [MODE/SET] to see current defrost frequency. 3 Defrost Frequency Setting Mode "dt" 3. To change the defrost frequency, press [UP or DOWN] until the desired value is displayed. 4. At the end of the sequence, press [MODE/SET] to set the value. 5. To display the cabinet temperature again, press [UP or DOWN] until [th] is displayed and then press [VERIFY] . - B11 - Mode Sign How to Setting (REFRIGERATOR) → ☞ → "dt" MANUAL/VERIFY D.F ☞ → → ☞ MODE/SET → 3 Defrost Frequency Setting Mode ☞ → → → ☞ → ☞ → MODE/SET → Setting Mode → No MODE/SET ☞ 6. Range of adjustable defrost frequency : 4Hr to 12Hr (The Unit of frequency : 2Hr) 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [dF] is displayed. 4 Forced Defrost Mode 2. Then press [MANUAL DF] more than 2 seconds to start forced defrost. "dF" ☞ → → MODE/SET ☞ → → ☞ More Than 2 Seconds MANUAL/VERIFY D.F 3. During defrosting, [dF] is displayed instead of the cabinet temperature. 5 Cancelation of Forced Defrost Mode 1. During forced defrost, press [MANUAL DF] more than Flash "dF" ☞ 2 seconds to stop forced defrost. More Than 2 Seconds MANUAL/VERIFY D.F 2. The [dF] will be flash 5 times and then return to normal display mode. 1. To enter this mode, press [MODE/SET] and [UP or DOWN] simultaneously until [th] is displayed. 2. Then press [MODE/SET] to see F-sensor, D-sensor temperature in turn. ☞ MODE/SET 6 Cabinet Temperature Verification Mode "th" → → ☞ → → ☞ → MODE/SET 3. To check only the F-sensor or D-sensor temperature, press [MODE/SET] again. → ☞ → MODE/SET 4. Press [VERIFY] to see current cabinet temperature. (return to normal display mode) - B12 - ☞ MANUAL/VERIFY D.F 3) NORMAL CONTROL PROCESS No FUNCTION SPEC (REFRIGERATOR) FUNCTION 1. After Power ON, Display panel will be lightened for 2 seconds with buzzer then 1 Initial Operating displays cabinet interior temperature. 2. If cabinet interior temperature is higher than 14℉, compressor will run without delay, and lower than 14℉, compressor will run after 3 minutes. 1. Compressor and condenser fan motor is controlled by T-sensor and MICOM program. 2 Normal Operating 2. Compressor ON/OFF Temperature Compressor ON : Temperature Setting Value ＋ (Temperature Differential Setting Value/2) Compressor OFF : Temperature Setting Value - (Temperature Differential Setting Value/2) ex) st: 39℉, di: 10℉ ⇒ Compressoer ON: 39+(10/2) = 44℉,Compressoer OFF: 39-(10/2) = 34℉ 1. Defrost Frequency : Preprogrammed frequency interval 2. Defrost time : 22 minutes 3 Defrost Mode 3. Defrost mode Operation 1) Compressor OFF, Condenser Fan OFF 2) Evaporator Fan ON 3) [dF] is displayed 1. Temperature Setting : 39℉, Temperature Differential Setting : 10℉ 4 Default Setting 2. Operating Temperature : 44℉(compressor on) ~ 34℉ (compressor off) 3. Defrost Frequency Setting : 6Hr 5 Setting Back UP 1. In case of unexpected power failure or power off, does not require resetting. 2. The setting is memorized. 1. If cabinet interior temperature is higher than 68℉, the panel displays [Hi], and lower than 14℉, the panel displays [Lo]. 6 Error Display Mode 2. Press [down] button 5 times with pressing and holding [up] button, the Error display mode is activated and it displays errors. 3. When there are more than 2 errors, the errors are displayed alternately. 4. If you press [MODE/SET] button, the Error Display Mode will be finished. - B13 - 4) ERROR CODE Error Code Condition C1 During normal mode (not defrost mode), T-sensor sensing is lower than 14℉ (display [Lo]) for 60min after. C2 During normal mode (not defrost mode), T-sensor sensing is higher than 68℉ (display [Hi]) for 60min after. C4 T-sensor sensing is more than 18℉ higher than temperature set point for 4hours Additionnal Possible Cause: Too many hot goods loaded!! C- No error code When error occurring, operation Possible Cause T-sensor defective 1) 2) 3) 4) 5) Register "C1" Compressor ON:15Minutes Compressor OFF:5Minutes Operate 2),3) three times Operate Normal Mode z T-sensor defective 1) 2) 3) 4) 5) Register "C2" Compressor OFF:22Minutes Compressor ON:15Minutes Operate 2),3) three times Operate Normal Mode z z Refrigerant leak Control board defective Door not sealing Not enough defrosts Condenser dirty Sensor defective 1) 2) 3) 4) 5) Register "C4" Compressor ON:20Minutes Compressor OFF:5Minutes Operate 2),3) three times Operate Normal Mode z N/A N/A z z z z z - B14 - 3. OPERATION FOR BASR1, BASR2, BAGR72 MODELS 1) BASIC OPERATION ① BASR1, BASR2 Models : Plug in the power cord and turn on the power switch located on the bottom of the top grille right side. [ The unit should be plugged into a 115V±10%, 60Hz (BASR1, BASR2)] ② BAGR72 Model : Plug in the power cord and turn on the lamp switch located on the left of the temperature controller. [ The unit should be plugged into a 115V±10%, 60Hz (BAGR72)] ③ The controller(Thermostat) has been preset "3" position(BASR1, BASR2, BAGR72 models) at the factory 2) DEFROST This unit uses an off cycle defrost. No needs any programming. 3) CONTROL TEMPERATURE ① The temperature controller is mounted on top of the cabinet interior. ② The controller has been preset "3" position(BASR1, BASR2, BAGR72 models) at the factory to maintain the average cabinet temperature of 38℉ ③ If you set the controller "7" position, the compressor will be run continuously. (BASR1, BASR2 models) ☞ To run like above more than two hours, it may cause the compressor to be damaged. The "7" position is for service technician only. 4) LAMP ① BASR1, BASR2 Models : The light inside cabinet comes on when the door is opened. ② BAGR72 Model : The light comes on when the lamp switch is on. OF ON F 1 2 3 7 OFF LAMP S/W Only 6 4 5 TEMP. CONTROLLER BAGR72 MODELS BASR1, BASR2 MODELS - B15 - 4. INSTRUCTION FOR RE-HINGING DOOR (BASF1, BASR1 MODELS) Top Grille 1 7 2 2 3 *8 4 4 ReRe-hinging 5 *9 6 * 10 7 1 Bottom Grille Figure 1. Figure 2. Turn the hinge in 4 180˚ * 8 A counterclockwise direction CABINET DOOR Figure 3. Figure 4. - B16 - ▣ Wear Protective glove when removing the hinges (#1,#7). ▣ In case of re-hinging door, door re-hinging kit (includes #8,#9,#10) will be used instead of #3, #5, #6. #8: Torsion coiled spring (C101-144-031), #9: Door Bushing (Upper)-L (C101-132-010) #10: Door Bushing (Lower)-L (C101-132-020) ▣ The silver color spring (#8) is for left hand hinged door and the yellow color spring (#3) is for right hand hinged door. ▣ The letter "L" is marked on the bushing (#9,#10). 1) STEP1. Remove the door (Figure 1) 1) Remove the top grille by unscrewing the eight screws and the bottom grille by unscrewing the four screws. 2) Remove the hinge (#1). 3) Lift and remove the door. 4) Remove the hinge (#7). 2) STEP2. Replace the part in the door (Figure 1 and 2) 1) Reverse the door. 2) Replace the spring guide (#4) with the bushing (#9). 3) Replace the bushing (#5) with the spring guide (#4). 3) STEP3. Adapt the hinges (Figure 1 and 2) 1) Remove the shaft (#2) from the hinge (#1). 2) Remove the bushing (#6) from the hinge (#7). 3) Install the shaft (#2) to the hinge (#7). 4) Install the bushing (#10) to the hinge (#1). 4) STEP4. Reinstall the door (Figure 2, 3, and 4) 1) Install the hinge (#1). 2) Install the door. 3) Insert spring (#8) into the spring guide (#4) as indicated in figure 3. 4) Install the hinge (#7) as indicated in figure 4. Be certain that the spring ends are engaged in the spring guide (#4) and the hinge (#7). 5) Install the top grille and the bottom grille. - B17 - ■ MODEL : BASF1/BASF2/BASF3(FREEZER) BASR1/BASR2/BASR3(REFRIGERATOR) BAGR72 (REACH-IN MERCHANDISERS) C. PARTS DIAGRAM AND LIST 1. CONDENSING UNIT - - - - - - - - - - - - - - - - - - - - - - 2 1) BASF1 (FREEZER) 2) BASF2 (FREEZER) 3) BASF3 (FREEZER) 4) BASR1 (REFRIGERATOR) 5) BASR2 (REFRIGERATOR) 6) BASR3 (REFRIGERATOR) 7) BAGR72 (REACH-IN MERCHANDISERS) 2. ASSEMBLY CABINET - - - - - - - - - - - - - - - - - - - - - 16 1) BASF1/BASR1 (1Door) 2) BASF2/BASR2 (2Door) 3) BASF3/BASR3 (3Door) 4) BAGR72 (Glass 3Door) 3. TOP GRILLE - - - - - - - - - - - - - - - - - - - - - - - - 28 1) BASF1/BASF2 (FREEZER) 2) BASF3 (FREEZER) 3) BASR3 (REFRIGERATOR) 4. TERMINAL BLOCK - - - - - - - - - - - - - - - - - - - - - - 34 1) BASF1/BASR1/BASF2/BASR2 2) BASF3/BASR3/BAGR72 5. ASSEMBLY OUTCABINET - - - - - - - - - - - - - - - - - - - - 36 1) BASF1/BASR1 (1Door) 2) BASF2/BASR2 (2Door) 3) BASF3/BASR3 (3Door) 4) BAGR72 (Glass 3Door) -1 - 1. CONDENSING UNIT 1) BASF1 (FREEZER) 14 3-1 10 11 3 22 9 16 21 19 21 13 21 18 8 12 21 6 7 21 15 20 4 5 21 2 23-1 23 17-1 1 17 -2 - CONDENSING UNIT No. Part Name BASF1 Part Number Description Q'ty 1 Ass'y Unit Base (F1) C101-130-080 G.I, 2.0t 1 2 Unit Base Plate (F1) C101-131-503 G.I, 1.6t 1 3 Compressor(2420A) C101-19D-000 CAE2420Z(A), 115V/60Hz 1 3-1 Bolt Washer for comp 7099-160-351 M6*35 4 4 Condenser Motor (UL) 0046-630-900 MA-7425W1, 120V/60Hz 1 5 Condenser Fan 0046-407-900 Al, Ø225 1 6 Cond. Motor Bracket 0040-101-001 G.I, 1.6t 1 7 Condenser (F1) C101-135-010 C1220TS-H, Ø9.52 1 8 Ass'y Suction Pipe (F1) C101-135-031 C1220T-O, Ø9.52 1 9 Capillary (B)-F1 C101-145-080 C1220T-H, Ø2.5 1 10 Discharge Pipe (F1) C101-135-041 C1220T-O, Ø6.35 1 11 Connect Drier Pipe (F1) C101-135-050 C1220T-O, Ø9.52 1 12 Drier 0046-526-300 XH-9 30g 1 13 Charge Pipe (Drier) 0046-520-400 C1220T-O, Ø6.35 1 14 Charge Pipe (Comp) C101-145-061 C1220T-O, Ø9.52 1 15 Dryer Brkt 0041-133-001 G.I, 1.2t 1 16 Cond. Fan Cover C101-134-190 MSWR10 1 17 Caster (4"-B) C101-198-130 TP5040-21 HDP TLB 2 C101-198-140 TP5040-21 HDP 2 0041-134-000 G.I, 0.5t 1 17-1 Caster (4") 18 Drier Band 19 Drier Band (Suction) 4444-000-0 G.I, 0.6t 2 20 Retainer Coil-90 6643-001-9 G.I, Coating 3 21 Tapping Screw (TH2) 7129-240-101 4*10 22 22 Tapping Screw (TH1) 7129-140-151 4*15 4 23 Drain Tray S150-432-122 HIPS 1 0044-455-401 120*138*2.5t 4 23-1 Vaporize Paper -3 - Remark 2) BASF2 (FREEZER) 12 3-3 9 10 3 21 19 22 16 8 21 21 18 21 13 3-2 11 6 7 3-1 21 21 14 5 4 20 21 2 23-1 21 15 23 17-1 1 17 -4 - CONDENSING UNIT No. Part Name BASF2 Part Number Description Q'ty 1 Ass'y Unit Base (F2) C102-130-080 G.I, 2.0t 1 2 Ass'y Unit Base Plate (F2) C102-130-193 G.I, 2.0t 1 3 Compressor(2432A) C102-19D-000 CAJ2432Z(A), 115V/60Hz 1 Comp. Relay Box C102-19A-001 For CAJ2432Z(A) 1 3-1 Starting Capacitor - 315㎌/160V 1 3-2 Running Capacitor - 30㎌/400V 1 3-3 Hex Bolt 7094-180-351 M8*35 4 4 Condenser Motor (UL) 0046-630-900 MA-7425W1, 120V/60Hz 1 5 Condenser Fan 0046-407-900 Al, Ø225 1 6 Cond. Motor Bracket 0040-101-001 G.I, 1.6t 1 7 Condenser (F2) C102-135-010 C1220TS-H, Ø9.52 1 8 Ass'y Suction Pipe (F2) C102-135-030 C1220T-O, Ø9.52/2.5 1 9 Discharge Pipe (F2) C102-135-040 C1220T-O, Ø6.35 1 10 Connect Drier Pipe (F2) C102-135-051 C1220T-O, Ø9.52 1 11 Drier 0046-526-300 XH-9 30g 1 12 Charge Pipe (Comp) 0045-507-401 C1220T-O, Ø6.35 1 13 Charge Pipe (Drier) 0046-520-400 C1220T-O, Ø6.35 1 14 Dryer Brkt 0041-133-001 G.I, 1.2t 1 15 Reinforce Angle 0046-131-403 G.I, 1.6t 3 16 Cond. Fan Cover C101-134-190 MSWR10 1 17 Caster (4"-B) C101-198-130 TP5040-21 HDP TLB 2 C101-198-140 TP5040-21 HDP 2 0041-134-000 G.I, 0.5t 1 17-1 Caster (4") 18 Drier Band 19 Drier Band (Suction) 4444-000-0 G.I, 0.6t 2 20 Retainer Coil-90 6643-001-9 G.I, Coating 3 21 Tapping Screw (TH2) 7129-240-101 4*10 31 22 Tapping Screw (TH1) 7129-140-151 4*15 4 23 Drain Tray (B) 0046-206-200 HIPS 1 23-1 Vaporize Paper 0046-430-401 105*105*2.5t 14 -5 - Remark 3) BASF3 (FREEZER) 12 3-3 9 10 3 21 19 22 16 8 21 21 18 21 13 11 6 7 3-1 21 3-2 21 14 4 5 20 21 2 23-1 21 15 23 1 17-1 17 -6 - CONDENSING UNIT No. Part Name BASF3 Part Number Description Q'ty 1 Ass'y Unit Base (F3) C103-130-000 G.I, 2.0t 1 2 Ass'y Unit Base Plate (F2) C102-130-193 G.I, 2.0t 1 3 Compressor(2446H) C103-19D-000 CAJ2446Z(H), 220V/60Hz 1 Comp. Relay Box C103-19A-040 For CAJ2446Z(H) 1 Starting Capacitor C103-19G-000 88㎌/260V/330V 1 3-2 Running Capacitor C103-19G-010 15㎌/440V 1 3-3 Hex Bolt 7094-180-351 M8*35 4 4 Condenser Motor (UL) 0046-630-900 MA-7425W1, 120V/60Hz 1 5 Condenser Fan 0046-407-900 Al, Ø225 1 6 Cond. Motor Bracket 0040-101-001 G.I, 1.6t 1 7 Condenser (F2) C102-135-010 C1220TS-H, Ø9.52 1 8 Ass'y Suction Pipe (F3) C103-135-020 C1220T-O, Ø12.7/4.76 1 9 Discharge Pipe (F2) C102-135-040 C1220T-O, Ø6.35 1 10 Connect Drier Pipe (F2) C102-135-051 C1220T-O, Ø9.52 1 11 Drier (F3) C103-135-030 XH-9 30g 1 12 Charge Pipe (Comp) 0045-507-401 C1220T-O, Ø6.35 1 13 Charge Pipe (Drier) 0046-520-400 C1220T-O, Ø6.35 1 14 Dryer Brkt 0041-133-001 G.I, 1.2t 1 15 Reinforce Angle 0046-131-403 G.I, 1.6t 4 16 Cond. Fan Cover C101-134-190 MSWR10 1 17 Caster (4"-B) C101-198-130 TP5040-21 HDP TLB 3 C101-198-140 TP5040-21 HDP 3 0041-134-000 G.I, 0.5t 1 3-1 17-1 Caster (4") 18 Drier Band 19 Drier Band (Suction) 4444-000-0 G.I, 0.6t 2 20 Retainer Coil-90 6643-001-9 G.I, Coating 3 21 Tapping Screw (TH2) 7129-240-101 4*10 33 22 Tapping Screw (TH1) 7129-140-151 4*15 4 23 Drain Tray (B) 0046-206-200 HIPS 1 23-1 Vaporize Paper 0046-430-401 105*105*2.5t 14 -7 - Remark 4) BASR1 (REFRIGERATOR) 3-1 10 3 14 11 22 9 16 21 19 21 13 21 18 8 12 21 6 7 21 15 4 5 20 21 2 23-1 23 17-1 1 17 -8 - CONDENSING UNIT No. Part Name BASR1 Part Number Description Q'ty 1 Ass'y Unit Base (F1) C101-130-080 G.I, 2.0t 1 2 Unit Base Plate (F1) C101-131-503 G.I, 1.6t 1 3 Compressor(SK6A1C) C111-19D-000 SK6A1C-H2Y, 115V/60Hz 1 Hex Bolt 0023-921-900 M6*35 4 4 Condenser Motor (UL) 0046-630-900 MA-7425W1, 120V/60Hz 1 5 Condenser Fan 0046-407-900 Al, Ø225 1 6 Cond. Motor Bracket 0040-101-001 G.I, 1.6t 1 7 Condenser (R700) 0044-502-203 C1220TS-H, Ø9.52 1 8 Ass'y Suction Pipe (R1) C111-135-030 C1220T-O, Ø9.52 1 9 Capillary (B)-R1 C111-145-080 C1220T-H, Ø3.0 1 10 Discharge Pipe (R1) C111-135-040 C1220T-O, Ø6.35 1 11 Connect Drier Pipe (R1) C111-135-050 C1220T-O, Ø9.52 1 12 Drier 0046-526-300 XH-9 30g 1 13 Charge Pipe (Drier) 0046-520-400 C1220T-O, Ø6.35 1 14 Charge Pipe (Comp) C111-145-061 C1220T-O, Ø6.35 1 15 Dryer Brkt 0041-133-001 G.I, 1.2t 1 16 Cond. Fan Cover C101-134-190 MSWR10 1 17 Caster (4"-B) C101-198-130 TP5040-21 HDP TLB 2 C101-198-140 TP5040-21 HDP 2 0041-134-000 G.I, 0.5t 1 3-1 17-1 Caster (4") 18 Drier Band 19 Drier Band (Suction) 4444-000-0 G.I, 0.6t 2 20 Retainer Coil-90 6643-001-9 G.I, Coating 3 21 Tapping Screw (TH2) 7129-240-101 4*10 22 22 Tapping Screw (TH1) 7129-140-151 4*15 4 23 Drain Tray S150-432-122 HIPS 1 0044-455-401 120*138*2.5t 4 23-1 Vaporize Paper -9 - Remark 5) BASR2 (REFRIGERATOR) 3-3 12 9 10 21 19 3 22 8 16 21 21 18 21 13 11 6 7 21 14 5 4 20 21 15 2 23-1 21 23 17-1 1 17 -10 - CONDENSING UNIT No. Part Name BASR2 Part Number Description Q'ty 1 Ass'y Unit Base (F2) C102-130-080 G.I, 2.0t 1 2 Unit Base Plate (R2) C112-190-100 G.I, 2.0t 1 3 Compressor(SK6A1C) C111-19D-000 SK6A1C-H2Y, 115V/60Hz 1 Hex Bolt 0023-921-900 M6*35 4 4 Condenser Motor (UL) 0046-630-900 MA-7425W1, 120V/60Hz 1 5 Condenser Fan 0046-407-900 Al, Ø225 1 6 Cond. Motor Bracket 0040-101-001 G.I, 1.6t 1 7 Condenser (R2) C112-135-010 C1220TS-H, Ø9.52 1 8 Ass'y Suction Pipe (R2) C112-135-030 C1220T-O, Ø9.52/3.0 1 9 Discharge Pipe (R2) C112-135-040 C1220T-O, Ø6.35 1 10 Connect Drier Pipe (R2) C112-135-050 C1220T-O, Ø9.52 1 11 Drier 0046-526-300 XH-9 30g 1 12 Charge Pipe (Comp) 0020-505-001 C1220T-O, Ø6.35 1 13 Charge Pipe (Drier) 0046-520-400 C1220T-O, Ø6.35 1 14 Dryer Brkt 0041-133-001 G.I, 1.2t 1 15 Reinforce Angle 0046-131-403 G.I, 1.6t 3 16 Cond. Fan Cover C101-134-190 MSWR10 1 17 Caster (4"-B) C101-198-130 TP5040-21 HDP TLB 2 C101-198-140 TP5040-21 HDP 2 0041-134-000 G.I, 0.5t 1 3-3 17-1 Caster (4") 18 Drier Band 19 Drier Band (Suction) 4444-000-0 G.I, 0.6t 2 20 Retainer Coil-90 6643-001-9 G.I, Coating 3 21 Tapping Screw (TH2) 7129-240-101 4*10 28 22 Tapping Screw (TH1) 7129-140-151 4*15 4 23 Drain Tray (B) 0046-206-200 HIPS 1 23-1 Vaporize Paper 0046-430-401 105*105*2.5t 14 -11 - Remark 6) BASR3 (REFRIGERATOR) 12 3-3 9 10 3 21 19 22 16 8 21 21 18 21 13 11 6 7 3-1 21 14 4 5 20 21 2 23-1 21 15 23 1 17-1 17 -12 - CONDENSING UNIT No. Part Name BASR3 Part Number Description Q'ty 1 Ass'y Unit Base (F3) C103-130-000 G.I, 2.0t 1 2 Ass'y Unit Base Plate (F2) C102-130-193 G.I, 2.0t 1 3 Compressor(4461A) C113-19D-000 CAJ4461Y(A), 115V/60Hz 1 Comp. Relay Box C113-19A-030 For CAJ4461Y(A) 1 Starting Capacitor S121-49G-000 250㎌/160V 1 Hex Bolt 7094-180-351 M8*35 4 4 Condenser Motor (UL) 0046-630-900 MA-7425W1, 120V/60Hz 1 5 Condenser Fan 0046-407-900 Al, Ø225 1 6 Cond. Motor Bracket 0040-101-001 G.I, 1.6t 1 7 Condenser (F2) C102-135-010 C1220TS-H, Ø9.52 1 8 Ass'y Suction Pipe (R3) C113-135-020 C1220T-O, Ø12.7/4.76 1 9 Discharge Pipe (R3) C113-135-030 C1220T-O, Ø6.35 1 10 Connect Drier Pipe (F2) C102-135-051 C1220T-O, Ø9.52 1 11 Drier (F3) C103-135-030 XH-9 30g 1 12 Charge Pipe (Comp) 0045-507-401 C1220T-O, Ø6.35 1 13 Charge Pipe (Drier) 0046-520-400 C1220T-O, Ø6.35 1 14 Dryer Brkt 0041-133-001 G.I, 1.2t 1 15 Reinforce Angle 0046-131-403 G.I, 1.6t 4 16 Cond. Fan Cover C101-134-190 MSWR10 1 17 Caster (4"-B) C101-198-130 TP5040-21 HDP TLB 3 C101-198-140 TP5040-21 HDP 3 0041-134-000 G.I, 0.5t 1 3-1 3-3 17-1 Caster (4") 18 Drier Band 19 Drier Band (Suction) 4444-000-0 G.I, 0.6t 2 20 Retainer Coil-90 6643-001-9 G.I, Coating 3 21 Tapping Screw (TH2) 7129-240-101 4*10 32 22 Tapping Screw (TH1) 7129-140-151 4*15 4 23 Drain Tray (B) 0046-206-200 HIPS 1 23-1 Vaporize Paper 0046-430-401 105*105*2.5t 14 -13 - Remark 7) BAGR72 (REACH-IN MERCHANDISERS) 12 3-3 9 10 3 21 19 22 8 16 21 21 18 21 13 3-1 11 6 21 14 7 4 5 20 21 23-1 2 21 15 23 1 17-1 17 -14 - CONDENSING UNIT No. Part Name BAGR72 Part Number Description Q'ty 1 Ass'y Unit Base (GR72) S121-430-061 G.I, 2.0t 1 2 Ass'y Unit Base Plate (F2) C102-130-193 G.I, 2.0t 1 3 Compressor(4476A) S121-49D-000 CAJ4476Y(A), 115V/60Hz 1 Comp. Relay Box S121-49A-030 For CAJ4476Y(A) 1 Starting Capacitor S121-49G-000 250㎌/160V 1 Hex Bolt 7094-180-351 M8*35 4 4 Condenser Motor (UL) 0046-630-900 MA-7425W1, 120V/60Hz 1 5 Condenser Fan 0046-407-900 Al, Ø225 1 6 Cond. Motor Bracket 0040-101-001 G.I, 1.6t 1 7 Condenser (F2) C102-135-010 C1220TS-H, Ø9.52 1 8 Ass'y Suction Pipe (R3) C113-135-020 C1220T-O, Ø12.7/4.76 1 9 Hot Pipe (GR72) S121-435-010 C1220T-O, Ø6.35 1 10 Connect Drier Pipe (F2) C102-135-051 C1220T-O, Ø9.52 1 11 Drier (F3) C103-135-030 XH-9 30g 1 12 Charge Pipe (Comp) 0045-507-401 C1220T-O, Ø6.35 1 13 Charge Pipe (Drier) 0046-520-400 C1220T-O, Ø6.35 1 14 Dryer Brkt 0041-133-001 G.I, 1.2t 1 15 Reinforce Angle 0046-131-403 G.I, 1.6t 4 16 Cond. Fan Cover C101-134-190 MSWR10 1 17 Adjust Foot 7094-000-700 SWRCH 12R 5 17-1 Adjust Foot (36) S121-444-120 SWRCH 12R*13 1 0041-134-000 G.I, 0.5t 1 3-1 3-3 18 Drier Band 19 Drier Band (Suction) 4444-000-0 G.I, 0.6t 2 20 Retainer Coil-90 6643-001-9 G.I, Coating 3 21 Tapping Screw (TH2) 7129-240-101 4*10 32 22 Tapping Screw (TH1) 7129-140-151 4*15 4 23 Drain Tray (B) 0046-206-200 HIPS 1 23-1 Vaporize Paper 0046-430-401 105*105*2.5t 8 -15 - Remark 37 36 e 13 Si d 34 20 14 Ev ra apo ca s 34 e 10-4 11 18 34 34 t or T-Sensor Fix er I nn Ev to r OFF 2 ra a po 16 4 19 3 -16 - 1 37 10-3 10 12 Fan Duct t as er c 10-2 10-1 9 6 I nn p o T Duc Fa n 17 e 7 15 5 8 3 38 4 4 34 5 t I 6 2-3 37 Fan Duct 9 F D uc an To p a se 2-2 rc nn e 7 8 23 22 34 1 2-4 2-1 35 2 2-5 21 24 29 34 32 25 26 28 31 30 27 33 2. ASSEMBLY CABINET 1) BASF1/BASR1 (1Door) 5 ASSEMBLY CABINET No. Part Name BASF1/BASR1 Part Number Description Q'ty Remark 1 Ass'y Lower Grille (F1) C101-130-032 F1/R1 1 2 Evaporator (F1) C101-125-000 C1220TS-O,H Ø9.52 1 Only BASF1 2-1 Sheath Heater (F1) C101-13L-081 120V/450W 1 Only BASF1 2-2 Heater Fixture C101-141-590 SUS304, 0.5t 1 Only BASF1 2-3 Drain Heater (A-F1) C101-13L-020 120V/60W 1 Only BASF1 2-4 Drain Heater (B) C101-14L-030 120V/9W 1 Only BASF1 2-5 Bi-Metal (BASF) C101-19I-000 115V/10A 1 Only BASF1 3 Evaporator (R1) C111-125-000 C1220TS-O,H Ø9.52 1 Only BASR1 4 Drain Pan (F1) C101-131-311 AL 1 5 Pan Adiabatic (F1) C101-134-100 F-P-S 1 6 Pan Guide C101-132-090 HIPS 1 7 Pan Cap C101-142-080 HIPS 1 8 Drain Hose (I) C101-143-090 PVC-S 1 9 Pan Packing C101-144-250 CR 1 10 Duct Body (F1) C101-121-270 SUS304 2B 1 Only BASF1 10-1 Duct Body (R1) C111-121-080 SUS304 2B 1 Only BASR1 10-2 Thermostat (K55) C111-19I-000 CCI Type, K55-Q5618 1 Only BASR1 10-3 Thermostat Bracket C111-141-100 SUS304 2B 1 Only BASR1 10-4 Thermostat Knob C111-132-000 ABS 1 Only BASR1 11 Side Duct (L) F1 C101-131-280 SUS304 2B 1 12 Side Duct (R) F1 C101-131-290 SUS304 2B 1 13 Cover Fan 0042-208-300 ABS 1 14 Ass'y Fan Duct (F1) C101-130-090 BASF1/BASR1 1 15 Motor Bracket 0044-122-300 G.I, 1.6t 1 16 Cooling Fan 0020-221-000 Zytel 1 17 Cooling Motor 0046-631-900 IS-3225LTSA, 120V/60Hz 1 18 Nut 7219-205-016 Stainless, M5 1 19 Star Washer 7329-105-006 0.5t 1 20 Clamp Tie (156) C101-198-190 CMCT-156 1 21 Lamp (40W) C101-19N-000 120V/40W 1 -17 - Only BASF1 ASSEMBLY CABINET No. Part Name BASF1/BASR1 Part Number Description Q'ty 22 Lamp Bracket C101-141-540 SUS304 2B 1 23 Lamp Socket C101-14F-051 PS 115(E27) 1 24 Lamp Cover C101-132-140 PC 1 25 Damper Cover C102-141-390 G.I, 1.0t 1 26 Damper Filter C101-144-200 Foam, 6t 4 27 Ass'y Damper C101-130-190 28 Lower Grille Fixture C101-141-341 G.I, 2.0t 2 29 Upper Grille Cover C101-141-551 SUS304 #4 1 30 Pilaster(Shelf Support) C101-132-200 A6063S-T5 4 31 Ass'y Door Hinge (Low-R) C101-130-010 32 Thin Screw (B) S103-148-191 S20C, Cr 4 33 Tapping Screw (TH1) 7129-140-251 4*25 (Zn) 2 34 Machine Screw (TH) 7029-140-106 M4*10 (STS304) 32 35 Tapping Screw (TH1) 7129-140-101 4*10 (Zn) 4 36 Machine Screw (TH) 7029-140-306 M4*30 (STS304) 4 37 Tapping Screw (TH1) 7129-140-106 4*10 (STS304) 10 38 Machine Screw (PH) 7069-140-101 M4*10 (Zn) 4 -18 - 1 1 Remark 37 38 T op In ner 13 se 20 p 14 Ev a 18 35 35 11 10-4 10 To OFF rc a 35 nne 35 p I ct n p I To se 9 6 ca 10-3 12 7 ner Fan Duct Du an t or F or a T-Sensor Fix ra 35 po ca Ev a 16 2 19 4 to r 3 -19 - 1 3 10-2 10-1 se 17 8 5 4 39 Fa n D 38 5 9 6 rc ne 7 In uct p To Fan Duct 15 a se 8 4 2-3 2-2 2 23 2-4 2-1 22 35 32 2-5 21 36 1 24 35 30 34 29 27 26 25 33 28 31 30-1 30 2) BASF2/BASR2 (2Door) 5 ASSEMBLY CABINET No. Part Name BASF2/BASR2 Part Number Description Q'ty Remark 1 Ass'y Lower Grille (F2) C102-130-062 F2/R2 1 2 Evaporator (F2) C102-125-000 C1220TS-O,H Ø9.52 1 Only BASF2 2-1 Sheath Heater (F2) C102-13L-081 120V/670W 1 Only BASF2 2-2 Heater Fixture C101-141-590 SUS304, 0.5t 4 Only BASF2 2-3 Drain Heater (A-F2) C102-13L-020 120V/90W 1 Only BASF2 2-4 Drain Heater (B) C101-14L-030 120V/9W 1 Only BASF2 2-5 Bi-Metal (BASF) C101-19I-000 115V/10A 1 Only BASF2 3 Evaporator (R2) C112-125-000 C1220TS-O,H Ø9.52 1 Only BASR2 4 Drain Pan (F2) C102-131-210 AL 1 5 Pan Adiabatic (F2) C102-134-000 F-P-S 1 6 Pan Guide C101-132-090 HIPS 1 7 Pan Cap C101-142-080 HIPS 1 8 Drain Hose (I) C101-143-090 PVC-S 1 9 Pan Packing C101-144-250 CR 1 10 Duct Body (F2) C102-121-270 SUS304 2B 1 Only BASF2 10-1 Duct Body (R2) C112-121-080 SUS304 2B 1 Only BASR2 10-2 Thermostat (K55) C111-19I-000 CCI Type, K55-Q5618 1 Only BASR2 10-3 Thermostat Bracket C111-141-100 SUS304 2B 1 Only BASR2 10-4 Thermostat Knob C111-132-000 ABS 1 Only BASR2 11 Side Duct (L) F2 C102-131-280 SUS304 2B 1 12 Side Duct (R) F2 C102-131-290 SUS304 2B 1 13 Cover Fan 0042-208-300 ABS 2 14 Ass'y Fan Duct (F2) C102-130-100 BASF2/BASR2 1 15 Motor Bracket 0044-122-300 G.I, 1.6t 2 16 Cooling Fan 0020-221-000 Zytel 2 17 Cooling Motor 0046-631-900 IS-3225LTSA, 120V/60Hz 2 18 Nut 7219-205-016 Stainless, M5 2 19 Star Washer 7329-105-006 0.5t 2 20 Clamp Tie (156) C101-198-190 CMCT-156 1 21 Lamp (40W) C101-19N-000 120V/40W 1 -20 - Only BASF2 ASSEMBLY CABINET No. Part Name BASF2/BASR2 Part Number Description Q'ty Remark 22 Lamp Bracket C101-141-540 SUS304 2B 1 23 Lamp Socket C101-14F-051 PS 115(E27) 1 24 Lamp Cover C101-132-140 PC 1 25 Damper Cover C102-141-390 G.I, 1.0t 1 26 Damper Filter C101-144-200 Foam, 6t 4 27 Ass'y Damper C101-130-190 28 Lower Grille Fixture C101-141-341 Center Post Ass'y(F2) C102-190-150 1 Only BASF2 Center Post Ass'y(R2) C112-190-110 1 Only BASR2 Pilaster(Shelf Support) C101-132-200 A6063S-T5 8 C121-443-110 A6063S-T5 1 1 G.I, 2.0t 2 29 30 30-1 Shelf Support Fixture (R) 31 Ass'y Door Hinge (Low-R) C101-130-010 1 32 Ass'y Door Hinge (Low-L) C102-130-030 1 33 Thin Screw (B) S103-148-191 S20C, Cr 4 34 Tapping Screw (TH1) 7129-140-251 4*25 (Zn) 2 35 Machine Screw (TH) 7029-140-106 M4*10 (STS304) 58 36 Tapping Screw (TH1) 7129-140-101 4*10 (Zn) 4 37 Machine Screw (TH) 7029-140-306 M4*30 (STS304) 8 38 Tapping Screw (TH1) 7129-140-106 4*10 (STS304) 14 39 Machine Screw (PH) 7069-140-101 M4*10 (Zn) 8 -21 - To p -22 - 37 e Inn 38 35 Eva 20 r to 18 rc e as 11 10 13 T-Sensor Fix ra po 19 p e Inn 5 35 er nn e cas 12 7 9 6 se 2-2 a rc or at Fan Duct To Ev or ap p I To 14 16 17 3 39 38 8 38 4 35 15 5 38 Fan Duct Top 7 9 6 2-2 se rca e n In 2 8 4 38 2-3 2-1 2-4 35 22 23 2-5 32 21 36 24 1 30 35 34 31-1 27 26 25 29 33 BASF3 28 31 30-1 30 3) BASF3/BASR3 (3Door) ASSEMBLY CABINET No. Part Name BASF3/BASR3 Part Number Description Q'ty Remark 1 Ass'y Lower Grille (F3) C103-130-050 F3/R3 1 2 Evaporator (F3) C103-125-000 C1220TS-O,H Ø12.7 1 Only BASF3 2-1 Sheath Heater (F3) C103-13L-000 120V/944W 1 Only BASF3 2-2 Evaporator Fixture (F3) C103-141-310 SUS304, 1.0t 1 2-3 Drain Pan Heater (F3) C103-13L-010 120V/138W 1 Only BASF3 2-4 Drain Heater (B) C101-14L-030 120V/9W 1 Only BASF3 2-5 Bi-Metal (BASF) C101-19I-000 115V/10A 1 Only BASF3 3 Evaporator (R3) C113-125-000 C1220TS-O,H Ø12.7 1 Only BASR3 4 Drain Pan (F3) C103-131-320 AL 1 5 Pan Adiabatic (F3) C103-137-000 F-P-S 1 6 Pan Guide C101-132-090 HIPS 1 7 Pan Cap C101-142-080 HIPS 1 8 Drain Hose (I) C101-143-090 PVC-S 1 9 Pan Packing C101-144-250 CR 1 10 Duct Body (F3) C103-121-330 SUS304 2B 1 11 Side Duct (L) F2 C102-131-280 SUS304 2B 1 12 Side Duct (R) F2 C102-131-290 SUS304 2B 1 13 Cover Fan 0042-208-300 ABS 3 14 Ass'y Fan Duct (F3) C103-130-190 BASF3/BASR3 1 15 Motor Bracket 0044-122-300 G.I, 1.6t 3 16 Cooling Fan 0020-221-000 Zytel 3 17 Cooling Motor 0046-631-900 IS-3225LTSA, 120V/60Hz 3 18 Nut 7219-205-016 Stainless, M5 3 19 Star Washer 7329-105-006 0.5t 3 20 Clamp Tie (156) C101-198-190 CMCT-156 1 21 Lamp (40W) C101-19N-000 120V/40W 2 22 Lamp Bracket C101-141-540 SUS304 2B 2 23 Lamp Socket C101-14F-051 PS 115(E27) 2 24 Lamp Cover C101-132-140 PC 2 25 Damper Cover C102-141-390 G.I, 1.0t -23 - 2 Only BASF3 1 Only BASR3 ASSEMBLY CABINET No. 26 27 28 Part Name Damper Filter Ass'y Damper BASF3/BASR3 Part Number C101-144-200 Description Q'ty Remark 8 Only BASF3 4 Only BASR3 2 Only BASF3 1 Only BASR3 Foam, 6t C101-130-190 Lower Grille Fixture C101-141-341 G.I, 2.0t 2 Center Post Ass'y(F3) C103-190-060 1 Only BASF3 Center Post Ass'y(R3) C113-190-180 1 Only BASR3 Pilaster(Shelf Support) C101-132-200 A6063S-T5 12 C121-443-110 A6063S-T5 2 29 30 30-1 Support Shelf Rack (Rear) 31 Ass'y Door Hinge (Low-R)-S C101-130-010 1 31-1 Ass'y Door Hinge (Low-C)-S C103-130-010 1 1 32 Ass'y Door Hinge (Low-L)-S C102-130-030 33 Thin Screw (B) S103-148-191 S20C, Cr 4 34 Tapping Screw (TH1) 7129-140-251 4*25 (Zn) 4 35 Machine Screw (TH) 7029-140-106 M4*10 (STS304) 59 36 Tapping Screw (TH1) 7129-140-101 4*10 (Zn) 8 37 Machine Screw (TH) 7029-140-306 M4*30 (STS304) 12 38 Tapping Screw (TH1) 7129-140-106 4*10 (STS304) 20 39 Machine Screw (PH) 7069-140-101 M4*10 (Zn) 12 -24 - 8 38 35 37 9 4 or 18 rat o p a Ev 19 -25 - 7 ON OFF L AMP S /W Onl y 6 5 1 4 2 CONTRO LLER OFF T EMP. 7 3 5 6 38 35 3 r ato r o ap Ev 40 14 16 17 13 38 20 39 12 11 41 10 20-1 20-2 20-3 38 15 Fan Duct Top 25 36 2 23 22 21 20-4 20-5 2-2 se rca e n In 38 24 41 35 32 1 25-1 34 31-1 27 28 28-2 28-1 29 26 33 30 31 25-1 4) BAGR72 (3Door) ASSEMBLY CABINET BAGR72 No. Part Name Part Number 1 Ass'y Lower Grille (GR72) S121-430-280 BAGR72 1 2 Evaporator (GR72) S121-425-000 C1220TS-O,H Ø12.7 1 Evaporator Fixture (GR72) S121-441-370 SUS304, 1.0t 1 3 Thermostat (GNA-246L) S121-49I-000 GNA-246L 1 4 Duct Body Ass'y(R72) S121-430-240 SECC 0.6T 1 5 Thermo Bracket Ass'y (R72) S121-440-331 LSR-BAGR72 1 6 Knob Thermostat 0042-210-401 ABS 1 7 Lamp Switch 0046-637-900 SL112A, 125V/12A 1 8 Cover Fan 0042-208-300 ABS 3 9 Duct Hinge (L) S121-441-000 SUS304, 2.0T 1 10 Duct Hinge (R) S121-441-010 SUS304, 2.0T 1 11 SUC-pipe Cover(R72) S121-443-090 PVC-H 1 12 Water Collector 0041-203-000 PP 2.0T 1 13 Drain Hose 0042-313-402 PVC-S 1 14 Fan Duct Ass'y(R72) S121-430-160 BAGR72 1 15 Motor Bracket 0044-122-300 G.I, 1.6t 3 16 Cooling Fan 0020-221-000 Zytel 3 17 Cooling Motor 0046-631-900 IS-3225LTSA, 120V/60Hz 3 18 Nut 7219-205-016 Stainless, M5 3 19 Star Washer 7329-105-006 0.5t 3 20 Lamp Base Ass'y (L) S121-430-201 BAGR72 1 20-1 Lamp Wire (Top-GR72)) S121-44F-060 UL1015 2 20-2 Lamp Wire (Bottom-GR72)) S121-44F-050 UL1015 2 20-3 Lamp(32W) S104-14N-000 FHF32SSEX-D-5, Ø26 2 20-4 Tube Lamp (B) 0046-317-400 PVC Mix, L=1153 2 20-5 Cap-Lamp 0040-201-000 PVC(Soft) 4 2-2 Description Q'ty 21 Lamp Base Ass'y (R) S121-430-211 BAGR72 1 22 Support Fixture Bracket S121-441-300 SUS304 2B, 0.8T 2 23 Support Shelf Rack (Front) S121-443-100 A6063S-T5, L=1367 2 24 Support Fixture (R72) S121-432-030 PA6 2 -26 - Remark ASSEMBLY CABINET BAGR72 No. Part Name Part Number 25 Pilaster(Shelf Support )-Solid C101-132-200 A6063S-T5 4 0043-113-300 A6063S-T5 8 25-1 Pilaster(Shelf Support )-R/I Description Q'ty 26 ballast (2-32W) S121-49C-000 DY232 IS120 (For 2 Lamp) 2 27 Ad. Panel Bracket (R72) S121-431-230 SGCC 1.2T 3 28 Ass'y Damper C101-130-190 28-1 Damper Cover C102-141-390 G.I, 1.0t 1 28-2 Damper Filter C101-144-200 Foam, 6t 4 1 29 Center Post Ass'y(R72) S121-490-170 BAGR72 2 30 Lower Grille Fixture C101-141-341 G.I, 2.0t 2 31 Ass'y Door Hinge (Low-R)-R S140-630-180 LSR-FH400 1 31-1 Ass'y Door Hinge (Low-C)-R S121-430-021 BAGR72 1 32 Ass'y Door Hinge (Low-L)_R S121-430-041 BAGR72 1 33 Thin Screw (B) S103-148-191 S20C, Cr 4 34 Tapping Screw (TH1) 7129-140-251 4*25 (Zn) 2 35 Machine Screw (TH) 7029-140-106 M4*10 (STS304) 11 36 Machine Screw (TH) 7029-140-166 M4*16 (STS304) 2 37 Machine Screw (TH) 7029-140-306 M4*30 (STS304) 12 38 Tapping Screw (TH1) 7129-140-106 4*10 (STS304) 86 39 Machine Screw (PH) 7069-140-101 M4*10 (Zn) 12 40 One Touch Screw S121-444-140 M4 (STS304) 2 41 Cap Nut S121-494-130 M4 (STS304) 2 -27 - Remark 3. TOP GRILLE 1) BASF1/BASF2 (FREEZER) DISPLAY PANEL MODE/SET MANUAL/VERIFY D.F White Black Gray 6 Blue MAIN HARNESS 5 12 4 RD Pink WH RD Gray ⓑ COMP 4 5 D-SENS T-SENS DISPLAY PCB ⓒ WH BK BK WH BL TRANS HTR FAN DOOR AC12V AC20V (DC24V) Gray Red Red TRANS POWER ⓐ (AC115V) FUSE 6 Black 1 (AC125V/8A) White Black Red White Pink 3 7 Orange DIP S/W 1 Blue 12 FRONT COVER (UPPER) ※ Check Point (When power is connected) ⓐ Housing "a" of main pcb (power input) : AC115V ⓑ Red wire of trans output : AC12V Blue wire of trans output : AC20V ⓒ Housing "c" of main pcb (Dc relay power input) : DC24V ※ If the dip s/w is existed, the dip s/w must be upward. (#1,#2 s/w) 2 13 8 FRONT COVER (UPPER) MODE/SET MANUAL/VER IFY D.F TOP OUTCASE 9 4 11 10 12 ⓑ Microchip 1 12 -28 - 3 TOP GRILLE No. BASF1/BASF2 Part Name Part Number Description Q'ty Remark 1 Control PCB Ass'y-BASF C101-19A-011 BASF1/BASF2 1 2 Front PCB Ass'y C101-19A-000 BASF1/BASF2 1 3 Main Trans (BASF) C101-19K-000 AC115V 1 4 DC Relay C101-19M-010 NAIS, HE1aN-Q-DC24V 1 5 Relay Connection Wire C101-14F-060 UL1015, AWG16,18 1 6 Front PCB Connection Wire C101-14F-070 UL1015, AWG24 1 Sensor (F1) C101-14J-000 BASF1 1 Only BASF1 Sensor (F2) C102-14J-000 BASF2 1 Only BASF2 8 PCB Cover (R-F) C101-122-151 ABS 1 9 Display Panel Sticker C101-136-040 PC 0.3T 1 10 Spacer Support (9N) C101-198-080 SJSS-9N 4 11 Card Support (9N) C101-198-170 CB-9N 1 12 Tapping Screw (TH1) 7129-140-101 4*10 (Zn) 4 13 Tapping Screw (PH2) 7109-240-061 4*6 (Zn) 6 7 -29 - 2) BASF3 (FREEZER) DISPLAY PANEL MODE/SET MANUAL/VERIFY D.F White Black Gray 6 Blue MAIN HARNESS RD 4 12 Gray 5 4 ⓒ WH BK BK WH BL TRANS HTR FAN DOOR AC12V AC20V (DC24V) Gray 3 ⓑ COMP ⓐ TRANS POWER (AC115V) 2 Black Pink WH RD D-SENS T-SENS DISPLAY PCB Black Red 5 6 Black 1 Red White Black Red White Pink 3 7 Orange 1 Blue 12 FRONT COVER (UPPER) ※ Check Point (When power is connected) ⓐ Housing "a" of main pcb (power input) : AC115V ⓑ Red wire of trans output : AC12V Blue wire of trans output : AC20V ⓒ Housing "c" of main pcb (Dc relay power input) : DC24V 2 13 8 FRONT COVER (UPPER) MODE/SET MANU AL/VE RIFY D.F TOP OUTCASE 9 4 11 10 12 ⓑ Microchip 1 12 -30 - 3 TOP GRILLE No. BASF3 Part Name Part Number Description 1 Control PCB Ass'y (F3) C103-19A-000 2 Front PCB Ass'y C101-19A-000 3 Main Trans (BASF) C101-19K-000 AC115V 1 4 DC Relay (2P) C103-19M-000 NAIS, HE2aN-Q-DC24V 1 5 Relay Connection Wire C101-14F-060 UL1015, AWG16,18 1 6 Front PCB Connection Wire C101-14F-070 UL1015, AWG24 1 7 Sensor (F3) C103-14J-000 BASF3 1 8 PCB Cover (R-F) C101-122-151 ABS 1 9 Display Panel Sticker C101-136-040 PC 0.3T 1 10 Spacer Support (9N) C101-198-080 SJSS-9N 4 11 Card Support (9N) C101-198-170 CB-9N 1 12 Tapping Screw (TH1) 7129-140-101 4*10 (Zn) 4 13 Tapping Screw (PH2) 7109-240-061 4*6 (Zn) 6 -31 - BASF3 Q'ty 1 1 Remark 3) BASR3 (REFRIGERATOR) DISPLAY PANEL MODE/SET MANUAL/VERIFY D.F White Black Gray 6 Blue MAIN HARNESS 5 12 4 RD WH RD Gray 4 5 T-SENS DISPLAY PCB ⓑ COMP ⓒ WH BK BK WH BL TRANS FAN DOOR AC12V AC20V (DC24V) Gray Red Red TRANS ⓐ (AC115V) POWER FUSE 6 Black 1 (AC125V/8A) White Black Red White 3 7 1 Orange 12 FRONT COVER (UPPER) ※ Check Point (When power is connected) ⓐ Housing "a" of main pcb (power input) : AC115V ⓑ Red wire of trans output : AC12V Blue wire of trans output : AC20V ⓒ Housing "c" of main pcb (Dc relay power input) : DC24V 13 2 8 FRONT COVER (UPPER) MOD E/SE T MANUAL/V ERIFY D.F TOP OUTCASE 9 4 11 10 12 ⓑ Microchip 1 12 -32 - 3 TOP GRILLE No. BASR3 Part Name Part Number Description 1 Control PCB Ass'y (F3) C113-19A-000 2 Front PCB Ass'y C101-19A-000 3 Main Trans (BASF) C101-19K-000 AC115V 1 4 DC Relay C101-19M-010 NAIS, HE1aN-Q-DC24V 1 5 Relay Connection Wire C101-14F-060 UL1015, AWG16,18 1 6 Front PCB Connection Wire C101-14F-070 UL1015, AWG24 1 7 Sensor (R3) C113-14J-000 BASR3 1 8 PCB Cover (R-F) C101-122-151 ABS 1 9 Display Panel Sticker C101-136-040 PC 0.3T 1 10 Spacer Support (9N) C101-198-080 SJSS-9N 4 11 Card Support (9N) C101-198-170 CB-9N 1 12 Tapping Screw (TH1) 7129-140-101 4*10 (Zn) 4 13 Tapping Screw (PH2) 7109-240-061 4*6 (Zn) 6 -33 - BASR3 Q'ty 1 1 Remark 4. TERMINAL BLOCK 1) BASF1/BASF2/BASR1/BASR2 White #18/#16 (2 Wire) White #18/#16 (2 Wire) Red Gray #18 Red Gray (2 Wire) Black Black #14 Cable Tie Terminal block (C101-19P-010) Cable Tie Terminal block (C101-19P-000) Retainer Coil Black White Retainer Coil Black White Red Power supply cord Green Wire Red Power supply cord Green Wire Power supply cord (B) (C101-14F-100) Terminal block Connection Wire (C101-14F-080) Power supply cord (B) (C101-14F-100) Terminal block wiring (BASF1) White #16 White #18 Black (2 Wire) Red Cable Tie Terminal block wiring (BASR1) Gray (or Blue) (2 Wire) Gray #18 (2 Wire) Black White Red Power supply cord Green Wire Power supply cord (B) (C101-14F-100) Terminal block (C101-19P-010) Gray Black White White #16 White #18 (2 Wire) Red Cable Tie Terminal block (C101-19P-020) Retainer Coil Retainer Coil Terminal block Connection Wire (C111-14F-021) Red Power supply cord Green Wire Terminal block Connection Wire (C101-14F-080) Power supply cord (B) (C101-14F-100) Terminal block wiring (BASF2) Terminal block Connection Wire (C111-14F-021) Terminal block wiring (BASR2) -34 - 2) BASF3/BASR3/BAGR72 White #16 White #18 Black (2 Wire) Red White #14 White #18 Black (2 Wire) Red Gray (2 Wire) Cable Tie Blue Cable Tie Terminal block (C101-19P-020) Retainer Coil Retainer Coil Gray Black Terminal block (C101-19P-020) Gray Black Red White White Power supply cord Green Wire Gray Red Power supply cord Green Wire Terminal block Connection Wire (C101-14F-080) Main harness Power supply cord (4-14) (C103-13A-030) Power supply cord (B) (C101-14F-100) Terminal block wiring (BASF3) Blue Glay Terminal block wiring (BASR3) Heater Connection Wire Black Red Black White White #16 White #18 (2선 Wire) Cable Tie Terminal block (C101-19P-020) Retainer Coil Black Red White Power supply cord Green Wire Power supply cord (B) (C101-14F-100) Terminal block Connection Wire (C101-14F-080) Terminal block Connection Wire (C101-14F-080) Terminal block wiring (BAGR72) -35 - 5. ASSEMBLY OUTCABINET 1) BASF1/BASR1 (1Door) RIGHT DOOR 2-2 1-1 2-1 1-2 BLUE AIR NSF 2 13 1 7 4 14 12 11 8 9 10 6 5 3-1 3 -36 - ASSEMBLY OUTCABINET No. 1 Part Name Ass'y Top Grille (F1) BASF1/BASR1 Part Number Description Q'ty Remark C101-120-155 BASF1 1 Only BASF1 1-1 Front PCB Ass'y C101-19A-000 BASF1/BASF2 1 Only BASF1 1-2 Display Panel Sticker C101-136-040 PC 0.3T 1 Only BASF1 Ass'y Top C111-120-114 BASR1 1 Only BASR1 2 Grille (R1) 2-1 Circular Thermometer C111-198-000 MILJOCO, V20462102-48 1 Only BASR1 2-2 Indicator Lamp (F-2C) C111-19N-000 NEON, 125V(GREEN) 1 Only BASR1 Door Ass'y (F1) C101-190-112 BASF1/BASR1 1 Torsion Spring Guide C101-132-000 ZNDC2, Die casting 1 4 Ass'y Door Hinge (Up-R) C101-130-000 BASF1,2/BASR1,2 1 5 Torsion Coiled Spring (R) C101-144-021 PW2, Zn Galvanizing 1 6 Lower Grille Fixture C101-141-341 G.I, 2.0t 4 7 DC Relay C101-19M-010 NAIS, HE1aN-Q-DC24V 1 Only BASF1 8 Control PCB Ass'y-BASF C101-19A-011 BASF1/BASF2 1 Only BASF1 9 Main Trans (BASF) C101-19K-000 AC115V 1 Only BASF1 10 Door Switch Support C101-142-210 ABS 1 11 Door Stopper C101-142-180 NR, H:13 3 12 Tapping Screw (TH1) 7129-140-154 4*15 (Cr) 3 13 Thin Screw (B) S103-148-191 S20C, Cr 8 14 HEX BOLT (M5×20) 7079-150-201 M5×20 4 3 3-1 -37 - Yellow -38 - 4 4-1 17 7 8 13 14 16 15 14 13 3-1 15 17 1 5 3 6 1-1 16 1-2 2 2-2 NSF BLUE A IR 2-1 10 11 9 12 RIGHT DOOR LEFT DOOR 2) BASF2/BASR2 (2Door) ASSEMBLY OUTCABINET No. 1 Part Name Ass'y Top Grille (F2) BASF2/BASR2 Part Number Description Q'ty Remark C102-120-205 BASF2 1 Only BASF2 1-1 Front PCB Ass'y C101-19A-000 BASF1/BASF2 1 Only BASF2 1-2 Display Panel Sticker C101-136-040 PC 0.3T 1 Only BASF2 Ass'y Top C112-120-134 BASR1 1 Only BASR2 2 Grille (R2) 2-1 Circular Thermometer C111-198-000 MILJOCO, V20462102-48 1 Only BASR2 2-2 Indicator Lamp (F-2C) C111-19N-000 NEON, 125V(GREEN) 1 Only BASR2 Door Ass'y (F2-R) C102-190-122 BASF2/BASR2 1 Torsion Spring Guide C101-132-000 ZNDC2, Die casting 1 Door Ass'y (F2-L) C102-190-112 BASF2/BASR2 1 Torsion Spring Guide C101-132-000 ZNDC2, Die casting 1 5 Ass'y Door Hinge (Up-R) C101-130-000 BASF1,2/BASR1,2 1 6 Torsion Coiled Spring (R) C101-144-021 PW2, Zn Galvanizing 1 7 Ass'y Door Hinge (Up-L) C102-130-020 BASF2/BASR2 1 8 Torsion Coiled Spring (L) C101-144-031 PW2, Zn Galvanizing 1 9 Lower Grille Fixture C101-141-341 G.I, 2.0t 5 10 DC Relay C101-19M-010 NAIS, HE1aN-Q-DC24V 1 Only BASF2 11 Control PCB Ass'y-BASF C101-19A-011 BASF1/BASF2 1 Only BASF2 12 Main Trans (BASF) C101-19K-000 AC115V 1 Only BASF2 13 Door Switch Support C101-142-210 ABS 2 14 Door Stopper C101-142-180 NR, H:13 6 15 Tapping Screw (TH1) 7129-140-154 4*15 (Cr) 6 16 Thin Screw (B) S103-148-191 S20C, Cr 10 17 HEX BOLT (M5×20) 7079-150-201 M5×20 8 3 3-1 4 4-1 -39 - Yellow White 4 4-1 17 7 8 13 14 15 14 13 3-1 15 17 16 5 3 6 1 14 13 3-1 15 17 2 5 3 6 16 2-1 LEFT DOOR 10 11 9 12 RIGHT/MIDDLE DOOR 3) BASF3/BASR3 (3Door) -40 - ASSEMBLY OUTCABINET No. Part Name Part Number Remark 2 Front PCB Ass'y C101-19A-000 Display Panel Sticker C101-136-040 PC 0.3T 1 Door Ass'y (F3-R) C103-190-030 BASF3/BASR3 2 Torsion Spring Guide C101-132-000 ZNDC2, Die casting 2 Door Ass'y (F3-L) C103-190-020 BASF3/BASR3 1 Torsion Spring Guide C101-132-000 ZNDC2, Die casting 1 5 Ass'y Door Hinge (Up-R) C101-130-000 BASF1,2/BASR1,2 2 6 Torsion Coiled Spring (R) C101-144-021 PW2, Zn Galvanizing 2 7 Ass'y Door Hinge (Up-L) C102-130-020 BASF2/BASR2 1 8 Torsion Coiled Spring (L) C101-144-031 PW2, Zn Galvanizing 1 9 Lower Grille Fixture C101-141-341 G.I, 2.0t 7 DC Relay (2P) C103-19M-000 NAIS, HE2aN-Q-DC24V 1 Only BASF3 DC Relay C101-19M-010 NAIS, HE1aN-Q-DC24V 1 Only BASR3 Control PCB Ass'y-BASF3 C103-19A-000 BASF3 1 Only BASF3 Control PCB Ass'y-BASR3 C113-19A-000 BASR3 1 Only BASR3 12 Main Trans (BASF) C101-19K-000 AC115V 1 13 Door Switch Support C101-142-210 ABS 3 14 Door Stopper C101-142-180 NR, H:13 9 15 Tapping Screw (TH1) 7129-140-154 4*15 (Cr) 9 16 Thin Screw (B) S103-148-191 S20C, Cr 14 17 HEX BOLT (M5×20) 7079-150-201 M5×20 12 3-1 4 4-1 BASF3/BASR3 Q'ty Ass'y Top 3 C103-120-040 Description 1 2-1 Grille (F3) BASF3/BASR3 1 1 Yellow White 10 11 -41 - -42 - 2 2-1 17 11 5 18 6 16 14 8 18 15 1-1 17 3 4 1 10 18 7 18 12 1-1 17 13 9 3 4 1 LEFT DOOR RIGHT/MIDDLE DOOR 4) BAGR72 (GLASS 3Door) ASSEMBLY OUTCABINET No. 1 Part Name BAGR72 Part Number Description Q'ty Door Ass'y (R72-R) S121-420-271 BAGR72 2 Torsion Spring Guide C101-132-000 ZNDC2, Die casting 2 Door Ass'y (R72-L) S121-420-261 BAGR72 1 Torsion Spring Guide C101-132-000 ZNDC2, Die casting 1 3 Ass'y Door Hinge (Up-R) S121-430-001 BAGR72 2 4 Torsion Coiled Spring (R) C101-144-021 PW2, Zn Galvanizing 2 5 Ass'y Door Hinge (Up-L) S121-430-031 BAGR72 1 6 Torsion Coiled Spring (L) C101-144-031 PW2, Zn Galvanizing 1 7 Ad. Panel Bracket (R72) S121-431-230 SGCC 1.2T 3 8 Ad. Panel Frame (Low-R72) S121-433-060 ABS 1 9 Ad. Panel Frame (Up-R72) S121-433-050 ABS 1 10 Ad. Panel (R72) S121-498-000 PC 2.0T, 1884×197 1 11 Ad. Panel Frame (L-R72) S121-432-000 ABS 1 12 Ad. Panel Frame (R-R72) S121-432-010 ABS 1 13 Lamp(32W) S104-14N-000 FHF32SSEX-D-5, Ø26 2 14 Lamp Wire (Ad. A-R72) S121-44F-010 UL1015 1 15 Lamp Wire (Ad. B-R72) S121-44F-020 UL1015 1 16 Cap-Lamp 0040-201-000 PVC(Soft) 4 17 HEX BOLT (M5×20) 7079-150-201 M5×20 12 18 Thin Screw (B) S103-148-191 S20C, Cr 43 1-1 2 2-1 -43 - Remark Yellow White ■ MODEL : BASF1/BASF2/BASF3(FREEZER) BASR1/BASR2/BASR3(REFRIGERATOR) BAGR72 (REACH-IN MERCHANDISERS) D. COMPRESSOR & ACCESSORIES CHECK LIST 1. BASF1 (FREEZER 1DOOR) - - - - - - - - - - - - - - - - - - - 3 2. BASF2 (FREEZER 2DOOR) - - - - - - - - - - - - - - - - - - - 4 3. BASF3 (FREEZER 3DOOR) - - - - - - - - - - - - - - - - - - - 5 4. BASR1/BASR2 (REFRIGERATOR 1,2DOOR) - - - - - - - - - - - - 6 - - - - - - - - - - - - - - - - 7 5. BASR3 (REFRIGERATOR 3DOOR) 6. BAGR72 (REACH-IN MERCHANDISERS 3DOOR) -1 - - - - - - - - - - - - 8 1. BASF1 (FREEZER 1DOOR) ① Compressor Spec. : CAE2420Z(A) (R404a), 115V/60Hz, CSIR Type ② Maker : TECUMSEH-FRANCE ③ Cooling Capacity : 572Kcal/Hr - LBP ④ Starting Capacitor Spec. : 315㎌ / 160V ⑤ Relay Spec. : 3ARR12KPF*483 ⑥ O.L.P Spec. : MST16AHN S M C 4 4 S M 3 1 3 C RELAY Comp. Terminal OLP * Comp. Winding Resistance : C - M → 0.8Ω, C - S → 3.1Ω (RT 68℉) * O.L.P Winding Resistance : 1 - C → 0 Ω (OK), ∞ Ω (NG) * Relay Winding Resistance : M - 4 → 0 Ω (OK), ∞ Ω (NG) S - 3 → ∞ Ω (OK) * Measuring the resistance, the bottom of the relay must be downward(like fig1) Black 1 OLP OLP C S/C AC115V 60Hz S M 3 RELAY S/C 4 RELAY White fig 1 (COMP. WIRING DIAGRAM) -2 - 2. BASF2 (FREEZER 2DOOR) ① Compressor Spec. : CAJ2432Z(A) (R404a), 115V/60Hz, CSR Type ② Maker : TECUMSEH-FRANCE ③ Cooling Capacity : 807Kcal/Hr - LBP ④ Starting Capacitor Spec. : 315㎌ / 160V ⑤ Running Capacitor Spec. : 30㎌ / 400V ⑥ Relay Spec. : 3ARR3*5R* ⑦ O.L.P Spec. : GA3PJU00 OLP C R/C S M S/C 3 EARTH RELAY BOX * Comp. Winding Resistance : C - M → 0.56Ω, C - S → 3.67Ω (RT 68℉) * O.L.P Winding Resistance : 3 - C → 0 Ω (OK), ∞ Ω (NG) * Relay Winding Resistance : 1 - 2 → 0 Ω (OK), ∞ Ω (NG) RELAY Black 2 WHITE WIRE 2 1 2N 3 OLP 3L 4 1 5 C 1 S/C AC115V 60Hz White BLACK WIRE R/C S (COMP. WIRING DIAGRAM) -3 - M 3. BASF3 (FREEZER 3DOOR) ① Compressor Spec. : CAJ2446Z(H) (R404a), 220V/60Hz, CSR Type ② Maker : TECUMSEH-FRANCE ③ Cooling Capacity : 1,219Kcal/Hr - LBP ④ Starting Capacitor Spec. : 88㎌ / 260V ⑤ Running Capacitor Spec. : 15㎌ / 400V ⑥ Relay Spec. : 3ARR3*3A* ⑦ O.L.P Spec. : MST00AHN OLP C R/C S M S/C 3 EARTH RELAY BOX * Comp. Winding Resistance : C - M → 1.16Ω, C - S → 8.14Ω (RT 68℉) * O.L.P Winding Resistance : 3 - C → 0 Ω (OK), ∞ Ω (NG) * Relay Winding Resistance : 1 - 2 → 0 Ω (OK), ∞ Ω (NG) RELAY Red BLACK WIRE 2 2 1 2N OLP 3L WHITE WIRE 3 4 5 C 1 S/C 1 R/C Red AC220V 60Hz S (COMP. WIRING DIAGRAM) -4 - M 4. BASR1/BASR2 (REFRIGERATOR 1,2DOOR) ① Compressor Spec. : SK6A1C-H2Y (R134a), 115V/60Hz, RSIR Type ② Maker : SAMSUNG-KOREA ③ Cooling Capacity : 1,080Kcal/Hr - HBP ④ Relay Spec. : MTRP0052-02 ⑤ O.L.P Spec. : 4TM 811XHBZZ-53 6 5 1 C (1) 4 S (6) M (5) COMP. Terminal 2 RELAY OLP * Comp. Winding Resistance : C - M → 1.03Ω, C - S → 7.5Ω (RT 77℉) * O.L.P Winding Resistance : 1 - 2 → 0 Ω (OK), ∞ Ω (NG) * Relay Winding Resistance : M(5) - 4 → 0 Ω (OK), ∞ Ω (NG) S(6) - 4 → ∞ Ω (OK) * Measuring the resistance, the bottom of the relay must be downward(like fig1) Black 1 OLP OLP C 1 S 6 RELAY 4 M 5 RELAY AC115V 60Hz fig 1 4 White (COMP. WIRING DIAGRAM) -5 - 5. BASR3 (REFRIGERATOR 3DOOR) ① Compressor Spec. : CAJ4461Y(A) (R134a), 115V/60Hz, CSIR Type ② Maker : TECUMSEH-FRANCE ③ Cooling Capacity : 1,586Kcal/Hr - HBP ④ Starting Capacitor Spec. : 250㎌ / 160V ⑤ Relay Spec. : 3ARR18A100B ⑥ O.L.P Spec. : GA3SJU81 or CRA38016 OLP C S M S/C 1 Earth RELAY BOX * Comp. Winding Resistance : C - M → 0.7Ω, C - S → 4.5Ω (RT 68℉) * O.L.P Winding Resistance : 1 - C → 0 Ω (OK), ∞ Ω (NG) * Relay Winding Resistance : L - 3 → 0 Ω (OK), ∞ Ω (NG) L - S → ∞ Ω (OK) * Measuring the resistance, the bottom of the relay must be downward(like fig1) RELAY 1 Black WHITE WIRE 3 OLP S L C 4 3 L White S fig 1 2 AC115V 60Hz S S/C (COMP. WIRING DIAGRAM) -6 - M Earth 3 BLACK WIRE 6. BAGR72 (REACH-IN MERCHANDISERS 3DOOR) ① Compressor Spec. : CAJ4476Y(A) (R134a), 115V/60Hz, CSIR Type ② Maker : TECUMSEH-FRANCE ③ Cooling Capacity : 1,946Kcal/Hr - HBP ④ Starting Capacitor Spec. : 250㎌ / 160V ⑤ Relay Spec. : 3ARR3*2M* ⑥ O.L.P Spec. : CRA38014 OLP C S M S/C 3 Earth RELAY BOX * Comp. Winding Resistance : C - M → 0.72Ω, C - S → 3.68Ω (RT 68℉) * O.L.P Winding Resistance : 3 - C → 0 Ω (OK), ∞ Ω (NG) * Relay Winding Resistance : 1 - 2 → 0 Ω (OK), ∞ Ω (NG) RELAY Black 2 WHITE WIRE 2 1 2N 3 OLP 3L 4 5 1 C 1 S/C AC115V 60Hz White BLACK WIRE S (COMP. WIRING DIAGRAM) -7 - M
![Maximum Model service Manual.ppt [호환 모드]](http://vs1.manualzilla.com/store/data/006002079_1-f9e925e4876feffe85b493d91263fd66-150x150.png)
