Download DUCATISPORTTOURING
Transcript
ORIENTAMENTO DEL PROIETTORE (fig. 49.1) Per controllare se il fanale è sistemato nella giusta posizione, mettete il motociclo, con i pneumatici gonfiati alla giusta pressione e con una persona seduta in sella, perfettamente perpendicolare con il suo asse longitudinale. Di fronte ad una parete o ad uno schermo, distante da esso 10 metri, tracciate una linea orizzontale corrispondente all’altezza del centro del fanale e una verticale in linea con l’asse longitudinale del veicolo. Effettuate il controllo possibilmente nella penombra. Accendendo la luce anabbagliante il limite superiore di demarcazione tra la zona oscura e la zona illuminata deve risultare ad una altezza non superiore a 9/10 dell’altezza da terra del centro del proiettore. Note La procedura descritta è quella stabilita dalla “Normativa Italiana” per quanto concerne l’altezza massima del fascio luminoso. Pertanto, gli Utenti di altri paesi, dovranno adeguare detta procedura secondo le prescrizioni in vigore nel loro paese. La rettifica dell’orientamento verticale del proiettore si può effettuare agendo sulla vite di regolazione (1, fig. 49.2), sul lato sinistro del proiettore, dopo aver rimosso la copertura laterale sinistra del cruscotto, come descritto a pag. 168. Ruotando la vite in senso orario il fascio luminoso si abbasserà, viceversa, si alzerà. La rettifica dell’orientamento orizzontale del proiettore si può effettuare agendo sulla vite di HEADLAMP ALIGNMENT (fig. 49.1) REGLAGE ASSIETTE DU PHARE (fig. 49.1) When checking headlamp alignment, put the motorcycle upright. Tyres should be inflated at the correct pressure and one person should be sitting astride the motorcycle, keeping it at right angles to its longitudinal axis. Place the motorcycle opposite a wall or a screen, 10 meters apart from it, then draw a horizontal line dictated by headlamp centre and a vertical one in line with the longitudinal axis of vehicle. If possible, perform this check in dim light. Switch on the low beam. The height of the light spot (measured at the upper limit between dark and lighted-up area) should not exceed 9/10th of the height from ground of headlamp center. Pour contrôler si le phare est bien positionné, mettez le motocycle, les pneus gonflés à la pression exacte et une personne assise en selle, parfaitement d’aplomb sur son axe longitudinal. En face d’une paroi, ou écran, à une distance de 10 m de celle-ci, tracez une ligne horizontale correspondant à la hauteur du centre du phare et une autre verticale alignée à l’axe longitudinal du véhicule. Effectuez le contrôle en pénombre autant que possible. Après allumage du feu de croisement, la limite supérieure de démarcation entre la zone sombre et la zone éclairée ne doit pas dépasser en hauteur 9/10 de la distance comprise entre le sol et le centre du phare. Note The procedure described here is in compliance with the “Italian Standard” establishing the maximum height of the light beam. Owners in other countries will adapt said procedure to the provisions in force in their countries. The height of the light beam can be corrected using the adjusting screw (1, fig. 49.2), on the left side of headlamp. To do this, remove the left side guard of the instrument panel following the instructions on page 168. Turn the screw clockwise to reduce the height of the light beam, anticlockwise to increase it. The side position of headlamp is adjusted using the adjusting screw (2, fig. 49.3), on the right side of headlamp. First, remove the right guard of the instrument panel following the instructions on page 168. Turn the screw clockwise to move the light beam to the right, anticlockwise to move it to the left. Notes La procédure décrite est établie par la “Réglementation Italienne” relativement à la hauteur maximum du faisceau lumineux. Par conséquent les Usagers d’autres pays, devront conformer cette procédure aux prescriptions en vigueur dans leur nation. La reprise de l’assiette verticale du phare peut être effectuée en intervenant sur la vis de réglage (1, fig. 49.2), du côté gauche du phare, après avoir ôté le cache latéral gauche du tableau de bord, comme décrit à la page 168. Si l’on tourne la vis dans le sens des aiguilles d’une montre, le faisceau lumineux baisse, vice versa il monte. La reprise de l’assiette horizontale du phare s’effectue en intervenant sur la vis de réglage (2, fig. 49.3), du côté droit du phare, après avoir ôté 234 6B_ST4.PM6 234 24-03-1905, 10:41