Download 2 - RcRevolution.net
Transcript
※ご使用前にこの説明書を良くお読みになり十分に理解してください。 Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS 組立/取扱説明書 INSTRUCTION MANUAL 1: 8 Scale Radio Controlled .21 Engine Powered 4WD Racing Buggy インファーノ MP9 TEAM KYOSHO INTERNATIONAL 目 次 INDEX ●キットの他にそろえる物 ●プロポの準備 ●組立て前の注意 REQUIRED FOR OPERATION RADIO PREPARATION 3 BEFORE YOU BEGIN 4〜5 ●ランナー付プラパーツ配置図 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ●本体の組立て ASSEMBLY ●取扱いの注意 OPERATING YOUR MODEL SAFELY ●分解図 2〜3 8 〜 36 37 EXPLODED VIEW ●スペアパーツ・オプションパーツリスト 38 〜 40 SPARE PARTS & OPTIONAL PARTS 安全のための注意事項 この無線操縦模型は玩具ではありません! ●この商品は高い性能を発揮するように設計されています。組立てに不慣れな方 は、模型を良く知っている人にアドバイスを受け確実に組立ててください。 ●小さい部品があるので、組立て作業は幼児の手がとどかない所で必ずおこなっ てください。 ●動かして楽しむ場所は、万一の事故を考えて安全を確認してから、責任をもっ てお楽しみください。 ●組立てた後も、説明書がいつでも見られるように大切に保管してください ●ラジコン保険に加入して安全に楽しみましょう。 41 〜 46 UNDER SAFETY PRECAUTIONS This radio control model is not a toy! ●First-time builders should seek the advice of experienced modelers before beginning assembly and if they do not fully understand any part of the construction. ●Assemble this kit only in places out of children's reach! ●Take enough safety precautions prior to operating this model. You are responsible for this model's assembly and safe operation! ●Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. ●Taking out liability insurance is recommended. ※製品改良のため、予告なく仕様を変更する場合があります。 *SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. © Copyright 2008 KYOSHO CORPORATION / 禁無断転載複製 31782-T01 6〜7 No. 31782 キットの他にそろえる物(1)REQUIRED FOR OPERATION (1) 1 ■スティックタイプ 2チャンネルプロポ Stick-type 2ch radio set. 2チャンネル2サーボ無線操縦機 (プロポ) 2ch radio control set with 2 servos. ●このキットには2チャンネル2サーボの プロポが必要です。 ●送信機にはスティックタイプとハンドル タイプがありますが、お好みのタイプを 用意してください。 ●スロットルサーボは、リバースで使用し ます。 ●プロポの取扱いは、プロポに付属の説明 書を参考にしてください。 ●This kit requires a 2 channel radio control set with 2 servos. ●Because there are stick-type and wheel-type transmitters, use whichever fits your convenience best. ●Switch the reverse (transmitter) for the throttle control. No.ORI12227 ORION1600 レシーバー パック(俵型:ユニプラグ) ORION1600 Receiver Pack Battery (Hump Type : Uniplug) No.ORI12232 ORION1600 レシーバー パック(俵型:BECプラグ) ORION1600 Receiver Pack Battery (Hump Type : BEC plug) ■ハンドルタイプ 2チャンネルプロポ Wheel-type 2ch radio set. 使用できるサーボ・受信機サイズ Suitable servos & receiver ■サーボ Servo ■単3乾電池(送信機用) AA-size Batteries (For Transmitter) ●For more information on the radio control set, refer to its instruction manual. 2 ■受信機用ニカドバッテリー Battery for Receiver エンジンおよびマフラー ■受信機 Receiver 31〜36mm AA AA 29〜32mm 38〜41mm 43〜48mm 18〜20mm エンジンに合わせて、以下のパーツが必要です。 Option parts for using option engines. Engine / Muffler / Tire ●このキットには21クラスエンジンが必要です。 ●This kit requires a .21 class engine. ■21クラスカー用エンジン Engine for .21-class cars ご使用になるエンジンに推奨されているものを、それぞれ使用してください。 Use components that are compatible with the engine you are using. プラグ Plug マニホールド Manifold マフラー Muffler ※ パイロットシャフト、クラ ンクシャフト一体型のエン ジンに限ります。 Use only .21 class engine with crank and pilot shaft (SG shaft only). 3 燃料と始動用具 ■燃料 Glow Fuel 塗料 Paint ●ボディの塗装には塗料が必要です。 京商では、モデル用塗料、スプレーを 販売していますのでご利用ください。 ●For painting the body, use Kyosho paints for models! ■燃料ポンプ Fuel Pump ■プラグヒーター Plug Heater No.73121 SUPER KANAI FUEL 30% Kyosho Racing SUPER KANAI FUEL 30% No.96423 フュールポンプ 500cc Fuel Bottle 500cc 京商スプレーカラー No.36217 No.36216S ブースターチャージャー 2.0 スパークブースター 2.0 KYOSHO SPRAY COLOR ■プラグレンチ Plug Wrench ■スターター Starter Nitro 30% No.80164 クロスレンチ (5.5/7/8/10mm) Cross Wrench (5.5 / 7 / 8 / 10mm) 5 4 Required for engine starting: その他 Other equipment required. No.76001〜76062 Booster Charger 2.0 No.36209 マルチスターターボックス2.0 Multi Starter Box 2.0 ■ダンパーオイル Shock Oil SI L IC O NE OI L Spark Booster 2.0 ■スターター用バッテリー Battery No.ORI10325 ORIONスポーツパワー2200 (ニッケル水素バッテリー) ORION Sport Power 2200 (Ni-MH Battery) ■ストラップ(M) Strap (M) No.1701KP / KY 蛍光ストラップ Fluorescent Strap ■エアークリーナーオイル Air Cleaner Oil No.96176 HGエアークリーナー オイル(100cc) HG Air Cleaner Oil (100cc) キットの他にそろえる物(2)REQUIRED FOR OPERATION (2) 6 組立てに必要な工具 ■ラジオペンチ Needle Nose Pliers Tools required 注意 ■+ドライバー(大、中、小) 使用する工具の取扱いには、 十分注意してください。 CAUTION: Handle tools carefully! Phillips Screwdriver (L.M.S) No.94402 ネジロック剤 (ロックタイト) Screw Cement ■ニッパー Wire Cutters ■カッターナイフ Sharp Hobby Knife LOCTITE ロックタイト ■キリ Awl キットに入っている工具 TOOLS INCLUDED ■六角レンチ(1.5mm, 2mm, 2.5mm, 3mm) No.96154 KYOSHO スペシャルグルー KYOSHO Special Glue ■10mmボックスドライバー Hex Wrench (1.5mm, 2mm, 2.5mm, 3mm) 10mm Box Wrench KYOSHO Special Glue 瞬間接着剤 Instant Glue ■グリス Grease Grease No.1829 No.36219 SPナイフエッジリーマー SP KNIFE EDGE REAMER ■十字レンチ Cross Wrench ラウンドカッター&サンダー ROUND CUTTER & SANDER No need to pre-drill! 下穴加工が不要で、直接 Precise holes (1mm to 1mm〜15mmの正確な 穴あけができる工具です。 15mm) can be drilled. ボディのカット、仕上 げ用。 曲線部分も楽に 作業ができます。 For trimming bodies! Easler cuts can be made along curved lines. プロポの準備 RADIO PREPARATION ●プロポを下の順番にしたがってセットします。 2 Set up the radio control system as indicated below. 6 ON 11 10 OFF 8 ●始める時 送信機 Transmitter ▲ 1 送信機に単3乾電池をセットする。 2 送信機のアンテナをのばす。 3 電充電した受信機用ニカド バッテリーをつなぐ。 4 受信機のアンテナをのばす。 5 トリムを中央にセットする。 6 送信機のスイッチを入れる。 7 受信機のスイッチを入れる。 8 ハンドル/トリガーを動かしてサ ーボが動いているか確認。 2 5 5 8 1 サーボ▼ Servo 6 ON 10 OFF ●終わる時 1 9 受信機のスイッチを切る。 10 送信機のスイッチを切る。 11 送信機のアンテナを縮める。 ●START 1 Insert AA-size batteries into the Transmitter. 2 Extend the Transmitter antenna. 3 Connect the charged Ni-Cd battery to the receiver. 4 Unwind the Receiver antenna. 5 Center the Transmitter trims. 6 Switch "ON" the Transmitter. 7 Switch "ON" the Receiver. 8 Make sure the servos move according to your transmitter inputs. ●FINISH 9 Switch "OFF" the Receiver. 10 Switch "OFF" the Transmitter. 11 Retract the Transmitter antenna. ▼受信機 Receiver 4 ▼スイッチ Switch ON 7 OFF 9 3 ▲バッテリー Battery 11 組立て前の注意(1) BEFORE YOU BEGIN (1) 1 組立てる前に説明書を良く読んで、おおよその構造を理解してから組立てに入ってください。 Read through the manual before you begin, so you will have an overall idea of what to do. 2 キットの内容をお確かめください。万一不良、不足がありましたら、お買い求めの販売店にご相談いただくか、当社「ユーザー相談室」までご連絡ください。 Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. 3 説明書の見かた How to read the instruction manual: 〔 1 フロントサスペンション Front Suspension Example 説明例 No.4, No.5, No.6 1 4 5 x 10mm メタル Metal Bushing 〕 説明書内では多くのマークが使用 されています。 マークに注意して 組立てを進めてください。 This instruction manual uses several symbols. Please note them during the entire assembly. 5 3 4 6 5 キングピン King Pin 4 4 7 R 2 6 5.8mm ピロボール(黒) Pillow Ball (Black) 5 2 小物部品の名前、 原寸図、 使用数。 Key Number, Part Name, True-to-scale Diagram, Quantity Used 4 キット内の部品は、 ビス類を除いてキー No. が付けられています。 スペアパーツを 購入する時はキー No.を参照してください。 All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. L 8 説明書に使われているマーク Symbols used throughout the instruction manual, comprise: 8mm の穴をあける (例) 。 Drill holes with the specified diameter (here: 5mm). 別購入品。 Must be purchased separately! グリスを塗る。 Apply grease. をカットする。 Cut off shaded portion. 注意して組立てる所。 Pay close attention here! 2セット組立てる(例)。 Assemble as many times as specified (here: twice). 仮止め。 Tentatively tighten. 原寸図。 True-to-scale diagram. 左右同じように組立てる。 Assemble left and right sides the same way. 番号の順に組立てる。 Assemble in the specified order. 可動するように組立てる。 Ensure smooth non-binding movement while assembling. 瞬間接着剤で接着する。 Apply instant glue (CA glue, super glue). 左側用。 For Left. 右側用。 For Right. 向きに注意。 Note the direction. ネジロック剤を塗る。 Apply threadlocker (screw cement). 使用する袋詰。 Part bags used. x2 8mm 組立て前の注意(2)BEFORE YOU BEGIN (2) 5 キットには、形や長さが違うビスや小物部品が多く入っています。 説明書には原寸図がありますので確認してから組立ててください。 また、ビス類は多めに入っているものもありますので、 予備としてお使いください。 This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. ●ビスの種類 SCREWS ビス Screw ●小物部品のサイズ例 OTHER HARDWARE TP ビス Self-tapping (TP) Screw 3x12mm ビス Screw 3mm ワッシャー・ナット Washer・Nut TP サラビス TP F/H Screw 12mm 3x12mm サラビス F/H Screw サラビス Flat Head (F/H) Screw 3mm 3mm 3mm キャップビス Cap Screw セットビス Set Screw 5x10mm メタル・ベアリング Metal Bushing・Bearing 5mm 6.8mm 10mm TPビスは、部品にネジを切りながらしめつけるビスです。しめこみが固い場合がありますが、 部品が確実に固定されるまでしめこんでください。ただし、しめすぎるとネジがきかなくなり ますので、部品が変形するまでしめないでください。 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. MEMO 6.8mm ピロボール Pillow Ball 3mm 12mm 6 E3 Eリング E-ring Correct Wrong しめすぎ Overtightened. ビスがきかない The threads are stripped. ランナー付プラパーツ配置図(1)ARRANGEMENT OF PLASTIC PARTS ON RUNNERS (1) No.1 No.3 57 57 28 27 23 25 18 17 63 29 29 30 73 部分の部品は、使用しません。 Shaded Parts are not used. 72 88B 88 87 L 64 H 9 50 64 9 49 47 2 2.5 2.5 3 68 68 70 3 45 50 49 47 2 73 72 87 L H 29 30 44 No.2 29 67 45B 34 34 34 34 32 42 32 33 31 39 41 部の部品は、セッティング用 に使用してくだい。 Use the parts within the dotted lines as tunning options. 40 40 39B 60 59 59 116 No.4 86 82 L 90 R 83 80 86 ランナー付プラパーツ配置図(2)ARRANGEMENT OF PLASTIC PARTS ON RUNNERS (2) 115 93 No.5 96 95 106 157 No.7 147 157 94 部分の部品は、 使用しません。 Shaded Parts are not used. 151 160 160 160 139 160 148 152 140 150 158 159 159 No.8 部分の部品は、 使用しません。 Shaded Parts are not used. 173 172 175 176 171 182 169 170 No.9 78 78 203 203 206 206 163 166 164 167 165 168 部分の部品は、 使用しません。 Shaded Parts are not used. 206 206 207 199 199 199 199 その他 Other 144 145 146 207 206 206 206 1 デフギヤ Gear Differential No.1 < フロント/リヤ用 > < For front and rear > < センター用 > < For center> 4x4mm 5 3 11 2 2 5 2 1 4 2 10 6 1 4 1 3 9 8 3 9 9 8 8 7 8 2 9 4 x 10mm シム Shim 12 使用する袋詰。 Part bags used. 7 8 8 9 9 5 2.5 x 13mm シャフト Shaft 3 x2 8 9 センター用 For center 2 8 x 16mm ベアリング Ball Bearing 4 6mm Oリング O-ring グリスを塗る。 Apply grease. 7 9 フロント/リヤ用 For front and rear 4 x 4mm セットビス Set Screw 8 9 7 6 3 3 番号の順に組立てる。 Assemble in the specified order. 原寸図。 True-to-scale diagram. x2 2セット組立てる (例) 。 Assemble as many times as specified. x1 2 デフギヤ Gear Differential No.1 < フロント/リヤ用 > < For front and rear > < センター用 > < For center> 5 A オイルは8分目まで入れる。 Fill up to 80%. B 小 Small C 大 Big 5 2 2 3 3 4 12 6 4 14 6 1 1 2 2 46 3 11 デフオイル Diff. Oil デフオイル Diff. Oil フロント用 For Front シリコンオイル#4000 Silicone Oil #4000 センター用 For Center シリコンオイル#4000 Silicone Oil #4000 リヤ用 For Rear A シリコンオイル#2000 Silicone Oil #2000 A 13 B 15 C 3x12mm フロント/リヤ用 For front and rear x2 センター用 For center 3x12mm x1 2 8 x 16mm ベアリング Ball Bearing 3x12mm 3x12mm 3 使用する袋詰。 Part bags used. 3 x 12mm サラヘックスビス F/H Hex Screw 12 グリスを塗る。 Apply grease. 5 2.5 x 13mm シャフト Shaft 番号の順に組立てる。 Assemble in the specified order. x2 3 4 6mm Oリング O-ring 2セット組立てる (例) 。 Assemble as many times as specified. 3 注意して組立てる所。 Pay close attention here! 3 リヤギヤボックス Rear Gearbox No.1 3 x 18mm サラヘックスビス F/H Hex Screw 2 17 1 19 5 x 11 x 4mm ベアリング Ball Bearing 19 3 2 20 13 x 16 x 0.15mm シム Shim 2 2 19 16 18 20 A リヤデフ Rear Differential A ギヤのバックラッシュが最適な値(ごく僅かにガタがある) に なるように 20シムで調整する。 Adjust with shim 20to set the optimal gear backlash (so there is still slight movement between the gears). 4 リヤギヤボックス Rear Gearbox 3x18mm 4x8mm No.1 23 5x4mm A 22 21 B 4x10mm 4 x 8mm ボタンヘックスビス Button Hex Screw 2 4 x 10mm サラヘックスビス F/H Hex Screw 2 使用する袋詰。 Part bags used. 5 x 4mm セットビス Set Screw グリスを塗る。 Apply grease. 1 番号の順に組立てる。 Assemble in the specified order. A 平らな面にセットビスを固定する。 Firmly tighten the set screws onto the flat spots. をカットする。 Cut off shaded portion. ネジロック剤を塗る。 Apply threadlocker (screw cement). B 長い Long 注意して組立てる所。 Pay close attention here! 5 リヤダンパーステー Rear Shock Stay No.1 A 25 3x22mm 24 26 3x10mm 3x10mm 3 x 22mm キャップビス Cap Screw 2 6 3 x 10mm サラヘックスビス F/H Hex Screw 4 ウイングステー Wing Stay A No.1 27 取付穴。 Holes for mounting. 30 3x15mm 29 28 29 30 3x10mm 29 3x15mm 3x10mm 3 x 10mm サラヘックスビス F/H Hex Screw 4 3 x 15mm ボタンヘックスビス Button Hex Screw 4 4 x 18mm ボタンヘックスビス Button Hex Screw 2 3 x 35mm キャップビス Cap Screw 1 3mm ナイロンナット Nylon Nut 3mm 1 3x35mm 4x18mm ビスの種類に注意。 Note the types of screws ! 使用する袋詰。 Part bags used. 注意して組立てる所。 Pay close attention here! 左右同じように組立てる。 Assemble left and right sides the same way. 7 リヤサスペンション Rear Suspension No.2 A 32 38 37 36 31 2 3 2 B 2 8x12x0.2mm Top 下 Bottom 4x12mm 5x4mm 1 上 車高調整用 For adjusting the ground clearance. 33 35 8 x 12 x 0.2mm シム Shim 34 6 3mm ナイロンナット Nylon Nut 41 2 34 38 2.6 x 17mm シャフト Shaft 2 3mm 2 8 x 16mm ベアリング Ball Bearing 35 サスシャフトスクリュー Suspension Shaft Screw 4 32 3 x 8 x 5mm プラカラー Plastic Collar 2 8 1mm 42 2 5 x 4mm セットビス Set Screw 4 x 12mm セットビス Set Screw リヤサスペンション Rear Suspension 2 A 32を他のスペーサーと交換 することで、ホイールベース の変更が可能。 Wheel base adjustments can be made by using other spacers. 2 B ガタがある場合は8x12x0.2mm シムを入れ、調整する。 In case of vibrations, insert a 8x12x0.2mm shim. No.1,2 46 4 x 68.5mm シャフト Shaft 2 4 x 25mm サラヘックスビス F/H Hex Screw 2 2 1 47 4 45B 3 46 2 44 1 4x25mm 3 使用する袋詰。 Part bags used. 左側用。 For Left. 右側用。 For Right. 45 左右同じように組立てる。 Assemble left and right sides the same way. 番号の順に組立てる。 Assemble in the specified order. 向きに注意。 Note the direction. 9 リヤサスペンション Rear Suspension A No.2 48 リヤアッパーロッド Rear Upper Rod 逆ネジ Reverse screw A 2 49 7.8mm ボールエンド Ball End 49 48 50 2 50 7.8mm ボールエンド Ball End 2 0 10 10 20 30 約16mm approx. 16mm 40 リヤサスペンション Rear Suspension x2 A No.2 1 2 51 43 3mm 3x22mm 3 A A 4 3x10mm 3 x 10mm キャップビス Cap Screw 43 7.8mm 座付ボール Flange Ball 2 2 2 2 使用する袋詰。 Part bags used. x2 3mm ナイロンナット Nylon Nut 3 x 22mm キャップビス Cap Screw 51 7.8mm ツバ付ボール Ball 番号の順に組立てる。 Assemble in the specified order. 2セット組立てる(例)。 Assemble as many times as specified. 2 原寸図。 True-to-scale diagram. 左右同じように組立てる。 Assemble left and right sides the same way. 注意して組立てる所。 Pay close attention here! 向きに注意。 Note the direction. 取付穴。 Holes for mounting. 11 リヤサスペンション Rear Suspension 55 5.8mm ボールエンド(L) Ball End (L) No.1,2 54 53 スタビボール Stabilizer Ball 2 54 5.8mm ボールエンド(S) Ball End (S) 2 3 x 10mm セットビス Set Screw 2 52 5.8mm ボール Ball 55 52 2 3x10mm 53 x2 2 3 x 15mm ボタンヘックスビス Button Hex Screw 2 3x15mm 3 x 3mm セットビス Set Screw 3x3mm 4 2 x 5mm ボタンヘックスビス Button Hex Screw 4 3 3x3mm 2 3 2 2.8 4 1 A 4 56 57 2x5mm 3x3mm 57 2x5mm A チューブを 56 に通し、ドライヤーで暖めて固定する。 Insert tube through the 56sway bar and secure using a hair dryer. 使用する袋詰。 Part bags used. 左右同じように組立てる。 Assemble left and right sides the same way. 番号の順に組立てる。 Assemble in the specified order. 5 5 2x5mm 3x3mm 可動するように組立てる。 Ensure smooth, non-binding movement when assembling. x2 2セット組立てる (例) 。 Assemble as many times as specified. 12 No.2 シャシー Chassis その他 Other 3x6mm 39 3x6mm 58 39 40 3 x 6mm ボタンヘックスビス Button Hex Screw 8 4 x 15mm サラヘックスビス F/H Hex Screw 4x15mm 4 40 13 4x15mm シャシー Chassis 59 No.2 3x20mm 3 x 12mm サラヘックスビス F/H Hex Screw 2 3mm 3 x 20mm キャップビス Cap Screw 1 3mm ナイロンナット Nylon Nut 60 2 3x12mm 使用する袋詰。 Part bags used. 左右同じように組立てる。 Assemble left and right sides the same way. 向きに注意。 Note the direction. 14 フロントギヤボックス Front Gearbox No.3 3 x 18mm サラヘックスビス F/H Hex Screw 2 17 1 19 5 x 11 x 4mm ベアリング Ball Bearing 19 3 2 20 13 x 16 x 0.15mm シム Shim 2 2 19 16 20 18 A フロントデフ Front Differential A ギヤのバックラッシュが最適な値(ごく僅かにガタがある) に なるように 20シムで調整する。 Adjust with shim 20to set the optimal gear backlash (so there is still slight movement between the gears). 15 フロントギヤボックス Front Gearbox 3x18mm No.1,2,3,4 5x4mm A 64 61 B 64 63 62 4x10mm 3x12mm 3 x 12mm サラヘックスビス F/H Hex Screw 2 4 x 10mm サラヘックスビス F/H Hex Screw 2 使用する袋詰。 Part bags used. 5 x 4mm セットビス Set Screw グリスを塗る。 Apply grease. 番号の順に組立てる。 Assemble in the specified order. 1 A をカットする。 Cut off shaded portion. 平らな面にセットビスを固定する。 Firmly tighten the set screws onto the flat spots. ネジロック剤を塗る。 Apply threadlocker (screw cement). 向きに注意。 Note the direction. B 短い Short 注意して組立てる所。 Pay close attention here! 16 フロントダンパーステー Front Shock Stay A No.3 3 x 22mm キャップビス Cap Screw 3x22mm 取付穴。 Holes for mounting. A 2 65 24 17 フロントサスペンション Front Suspension A No.2,3,4 66 フロントアッパーロッド Front Upper Rod 67 2 逆ネジ Reverse screw B 長い Long 70 66 68 6.8mm ボールエンド Ball End 69 6.8mm ツバ付ボール Ball Rのマーク Marked “R” B 2 Lのマーク Marked “L” A 2 約10mm approx. 10mm 68 0 10 20 30 69 40 3 x 10mm サラヘックスビス F/H Hex Screw 3 4 x 10mm サラヘックスビス F/H Hex Screw 2 71 3 x 29.5mm シャフト Shaft 2 71 73 3x10mm 73 72 3x10mm 4x10mm L 3x10mm 使用する袋詰。 Part bags used. 原寸図。 True-to-scale diagram. 左右同じように組立てる。 Assemble left and right sides the same way. 注意して組立てる所。 Pay close attention here! 左側用。 For Left. 右側用。 For Right. 向きに注意。 Note the direction. 18 フロントサスペンション Front Suspension No.4 79 4 内側 Inside 76 下 Bottom 外側 Outside 75 38 36 2 8x12x0.2mm 37 80 3 77 75 5x4mm 2 79 76 77 79 4 x 10mm キングピン King Pin 4 75 ナックルカラー Knuckle Collar 82 38 2.6 x 17mm シャフト Shaft 2 5 x 4mm セットビス Set Screw 2 8 x 16mm ベアリング Ball Bearing 8 x 12 x 0.2mm シム Shim 4 81 2 6 4 A フロントサスペンション Front Suspension 3mm ガタがある場合は8x12x0.2mmシムを入れ、調整する。 In case of vibrations, insert a 8x12x0.2mm shim. No.2,4 A 7 6 L 19 下 Bottom 4 1 A 81 2 2 90 3 3 88B Lのマーク Marked “L” 89 3x22mm 4 87 2 1 4x22mm 4x12mm 86 上 Top R 85 5 下 Bottom Rのマーク Marked “R” 83 2.6mm 2.6 x 5mm ボタンヘックスビス Button Hex Screw 2 4 x 22mm ボタンヘックスビス Button Hex Screw 2 使用する袋詰。 Part bags used. 3 x 22mm キャップビス Cap Screw 2 4 x 12mm セットビス Set Screw 88 3mm ナイロンナット Nylon Nut 2 84 3 x 35mm シャフト Shaft 2 左側用。 For Left. 2.6mm ワッシャー Washer A 2 向きに注意。 Note the direction. 右側用。 For Right. 2 2 85 4 x 64.5mm シャフト Shaft 番号の順に組立てる。 Assemble in the specified order. 左右同じように組立てる。 Assemble left and right sides the same way. 車高調整用 For adjusting the ground clearance. 1 2.6x5mm 84 1mm 注意して組立てる所。 Pay close attention here! ネジロック剤を塗る。 Apply threadlocker (screw cement). 取付穴。 Holes for mounting. 20 フロントサスペンション Front Suspension 55 5.8mm ボールエンド(L) Ball End (L) No.3,4 54 53 スタビボール Stabilizer Ball 2 54 5.8mm ボールエンド(S) Ball End (S) 2 3 x 10mm セットビス Set Screw 2 52 5.8mm ボール Ball 55 52 2 3x10mm 53 x2 2 3 x 15mm ボタンヘックスビス Button Hex Screw 2 3x15mm 3 x 3mm セットビス Set Screw 4 2 x 5mm ボタンヘックスビス Button Hex Screw 4 3x3mm 3 3x3mm 3 2 4 2 4 91 2.5 57 A 1 2x5mm 3x3mm 57 2x5mm 5 5 2x5mm 3x3mm A チューブを 91 に通し、ドライヤーで暖めて固定する。 Insert tube through the 91sway bar and secure using a hair dryer. 使用する袋詰。 Part bags used. 左右同じように組立てる。 Assemble left and right sides the same way. 番号の順に組立てる。 Assemble in the specified order. 可動するように組立てる。 Ensure smooth, non-binding movement when assembling. x2 2セット組立てる (例) 。 Assemble as many times as specified. 21 シャシー Chassis No.4 92 1 3 x 10mm ボタンヘックスビス Button Hex Screw 2 1 4x15mm 4 センターギヤボックス Center Gearbox No.5 99 96 95 98 97 3x10mm 4x15mm 4 x 15mm サラヘックスビス F/H Hex Screw 22 2 97 97 98 97 94 99 センターデフ Center Differential 93 3x6mm 3x6mm 3 x 6mm サラヘックスビス F/H Hex Screw 2 97 ブレーキパッド Brake Pad 4 99 16.5mm ディスクプレートボルト Disk Plate Bolt 4 使用する袋詰。 Part bags used. 約8.5mm approx. 8.5mm 番号の順に組立てる。 Assemble in the specified order. 約8.5mm approx. 8.5mm 原寸図。 True-to-scale diagram. 23 センターギヤボックス Center Gearbox No.5 4 x 10mm サラヘックスビス F/H Hex Screw 4 78 A A 78 4x10mm 4x10mm 24 センターギヤボックス Center Gearbox 3 x 3mm セットビス Set Screw No.5 3x3mm A オプションのスパーギヤ48Tを 使用する場合は 78 を使用する。 If using optional 48T spur gear, use 78. 4.5mm 3mm 103 B B 2 3 x 8mm ボタンヘックスビス Button Hex Screw 4 3x8mm 3x8mm 3x10mm 104 A 3 x 10mm ボタンヘックスビス Button Hex Screw 1 3mm ナイロンナット Nylon Nut 1 106 105 3mm 105 101 102 3x3mm 101 100 100 A 使用する袋詰。 Part bags used. 原寸図。 True-to-scale diagram. 注意して組立てる所。 Pay close attention here! ロッドがセンターデフにあたる場合は B 曲げてあるロッド Curved Rod ペンチで曲げる。 Bend the rods if they contact the Center Diff. 25 ステアリング Steering No.5 前 Front 112 111 113 112 3x10mm 4x10mm 4x10mm 111 109 113 4 x 10mm サラヘックスビス 111 ステアリングカラー Steering Collar F/H Hex Screw 2 108 2 3mm ナイロンナット Nylon Nut 3 109 6 x 10mm ベアリング Ball Bearing 4 3mm 109 109 3mm 110 3 x 10mm ワッシャー Washer 110 2 2 26 3x10mm 3mm 112 ステアリングピン Steering Pin 109 107 ステアリング Steering 4x10mm No.2,5 A 3x12mm 3 x 10mm サラヘックスビス F/H Hex Screw 1 3 x 12mm サラヘックスビス F/H Hex Screw 3 B 114 A C 115 3mm 4 x 10mm サラヘックスビス F/H Hex Screw 4 3mm ナイロンナット Nylon Nut 116 3x10mm 3mm 3 ビスの種類に注意。 Note the types of screws ! A B 仮止めのビスを外して使う。 Remove these screws and retighten after installing 114. 広い Wide C 使用する袋詰。 Part bags used. 狭い Narrow 仮止め。 Temporarily tighten. 3x12mm 4x10mm 向きに注意。 Note the direction. 4x10mm 注意して組立てる所。 Pay close attention here! ネジロック剤を塗る。 Apply threadlocker (screw cement). 可動するように組立てる。 Ensure smooth, non-binding movement when assembling. 27 ステアリング Steering A 117 No.5 118 3mm (ナイロンナット) (Nylon Nut) B 119 120 118 約28mm approx. 28mm 3x15mm 0 10 20 30 118 6.8mm ボールエンド(L) Ball End (L) 4 2 3mm 3mm ナイロンナット Nylon Nut 2 2 28 3mm 3 x 15mm サラヘックスビス F/H Hex Screw 117 タイロッド Tie Rod 4 120 6.8mm ボール Ball 3x15mm x2 40 エンジン Engine 119 6.8mm ナット Nut 2 座付ボール Flange Ball 2 A 段のある方が逆ネジ。 The side with the step is a reverse screw. B 取付穴。 Holes for mounting. No.6 エンジン Engine 122 テーパーコレット Tapered Collet エンジン Engine 1 124 パイロットナット Pilot Nut 1 125 3 x 5 x 0.2mm シム Shim A 123 3 122 121 124 121 7 x 11mm ワッシャー Washer B 1 A B 126 125 127 クランクシャフトを引っ張り 出した状態で組み立てる。 Assemble the following parts with pulling the crankshaft. D 127 必ずキット付属の 122テーパー コレットを使用する。 Use 122taper collet included in the kit. C 126 の短い方を 124の 溝に入れる。 The short side of 126 must be in the groove of 124 . 使用する袋詰。 Part bags used. D 125 127 C 126 126 No.36206 3PCクラッチシュ ーツールを使用すると便利です。 When assembling the clutch shoe, it is easier to assemble using the 3pc Clutch Shoe Tool (No.36206). 注意して組立てる所。 Pay close attention here! 原寸図。 True-to-scale diagram. ネジロック剤を塗る。 Apply threadlocker (screw cement). 124 126 別購入品。 Must be purchased separately! 左右同じように組立てる。 Assemble left and right sides the same way. x2 2セット組立てる(例)。 Assemble as many times as specified. 29 エンジン Engine No.6 エンジン Engine 3 x 6mm ボタンヘックスビス 130 5 x 10mm ベアリング Ball Bearing Button Hex Screw 1 2 3 x 10mm キャップビス Cap Screw 4 133 5 x 8.5 x 0.2mm シム Shim 3 A エンジン Engine シム Shim 3x10mm 1 132 5 x 10 x 0.5mm ワッシャー Washer 1 130 131 130 129 3x10mm 132 エンジンによってワッシャー及び シムの種類、枚数を調整する。 A number and / or type of shim need to be adjusted depending on the type of engine. 30 129 5 x 20mm 3x6mm A 133 No.6 128 A 前 Front 134 134 4x8mm 4x6mm 4x8mm 4x6mm 128 A 後 Rear 134 4 x 6mm サラヘックスビス F/H Hex Screw 4 x 8mm フランジ付キャップビス Flanged Cap Screw 4 B 21がエンジンに干渉する場合 4 21 使用する袋詰。 Part bags used. ネジロック剤を塗る。 Apply threadlocker (screw cement). 可動するように組立てる。 Ensure smooth, non-binding movement when assembling. 紙1枚分のすき間をつくって 固定する。 Tighten the screws with one sheet of paper inserted between both gears. 別購入品。 Must be purchased separately! は干渉部をカットする。 If 21contacts the engine, trim away where required. B 向きに注意。 Note the direction. をカットする。 Cut off shaded portion. 31 マフラー Muffler 4 x 4mm セットビス Set Screw 1 No.6 3 x 6mm サラヘックスビス F/H Hex Screw 2 マニホールド Manifold 4x4mm 135 136 A マフラー Muffler A 3x6mm 32 燃料タンク Fuel Tank マフラーに合わせて曲げる。 Bend so it fits into the muffler. No.7 3x15mm 3x15mm 3 x 15mm ボタンヘックスビス Button Hex Screw 2 137 137 3 x 10mm サラヘックスビス F/H Hex Screw 2 141 8.5mm ブッシュ Bushing 138 2 138 139 138 140 141 3x10mm 3x10mm 使用する袋詰。 Part bags used. 別購入品。 Must be purchased separately! 向きに注意。 Note the direction. 33 No.5,7 サイドガード Side Guard 143 C その他 Other 143 C 142 B 143 C 3mm (ナイロンナット) (Nylon Nut) 146 3mm 147 143 3x10mm 147 3x10mm 3x10mm A 3mm 3 x 6mm ボタンヘックスビス Button Hex Screw 2 3x10mm 3 x 7mm 3 x 10mm サラヘックスビス F/H Hex Screw 7 3mm 34 ナット Nut 2 D 1 3mm ナイロンナット Nylon Nut 1 プロポ Radio A 排気口に合わせる。 Trim the shaded portion away so the exhaust pipe can exit. B Oリングの向きに注意。 Note the direction for O-ring. C エンジン、マフラーに合せてシリコンチューブの長さを調節する。 Cut the 143Silicone Tube, depending on Engine and Muffler. D マフラーが 144に干渉する場合は干渉部をカットする。 If muffler contacts 144 , trim away where required. No.7 151 2x6mm 2x5mm 2 x 6mm ボタンヘックスビス Button Hex Screw 1 150 2 x 42mm ボタンヘックスビス Button Hex Screw 1 152 スイッチ Switch 2 x 5mm ボタンヘックスビス Button Hex Screw 3 A 145 3x6mm ワッシャー Washer 144 3 149 1 スイッチ Switch 前 Front 2x42mm 2 OFF ON 使用する袋詰。 Part bags used. 148 別購入品。 Must be purchased separately! A 注意して組立てる所。 Pay close attention here! をカットする。 Cut off shaded portion. 前側で ON になるように組み立てる。 Assemble so ON is towards the front. 番号の順に組立てる。 Assemble in the specified order. 左右同じように組立てる。 Assemble left and right sides the same way. 35 No.7 プロポ Radio その他 Other アンテナ Antenna 3x3mm 153 アンテナパイプ Antenna Pipe バッテリー Battery 受信機 Receiver A B 154 3 x 3mm セットビス Set Screw 155 フックピン Hook Pin 1 2 155 A メカボックスのすき間には、スポンジ等を入れると良い。 Better to fill some sponge between radio box and receiver as well as battery. B 使用する受信機によっては折り曲げずに取付ける。 詳しくはご使用になるプロポの説明書に従ってください。 Will not require bending depending the receiver used. For details, refer to R/C system instruction manual. 36 プロポ Radio 155 プロポの説明書を参考に、 コネクターを接続する。 Connect as per radio instruction manual. No.7 3 x 10mm サラヘックスビス F/H Hex Screw 2 3x10mm 使用する袋詰。 Part bags used. 別購入品。 Must be purchased separately! 注意して組立てる所。 Pay close attention here! 37 プロポ Radio No.5,7,8 3x15mm 3x15mm 3 x 10mm サラヘックスビス F/H Hex Screw 2 3x15mm 3x15mm 3 x 15mm ボタンヘックスビス Button Hex Screw スロットルサーボ Throttle Servo 8 B ステアリングサーボ Steering Servo B A 159 3x10mm 159 A 156 A 38でサーボがシャシーに干渉する 場合は 159を使用する。 If servo interferes with chassis at step 38, use .159 B 157 157 サーボに付属のゴムブッシュと カラーを必ず使用する。 Use rubber bushings and collars included in the servo. 38 プロポ Radio 157 157 158(トランスポンダーステー用) (For transponder.) No.7 A 3x10mm 3x10mm 3x10mm コネクターを接続する。 Connect as per radio. 3 x 10mm サラヘックスビス F/H Hex Screw 10 160 A 160 160 160 コード Cords 3x10mm 使用する袋詰。 Part bags used. 別購入品。 Must be purchased separately! 3x10mm 39 プロポ Radio No.8 162 55 5.8mm ボールエンド(L) Ball End (L) A 2 161 ステアリングロッド Steering Rod 55 161 1 55 162 5.8mm 座付ボール Flange Ball 162 2 40 A プロポ Radio 段のある方が逆ネジ。 The side with the step is a reverse screw. No.8 3 x 15mm サラヘックスビス F/H Hex Screw 2 A B 165 サンワ, KO, JR SANWA(AIRTRONICS), KO, JR H 164 H ハイテック HiTEC F 163 F フタバ Futaba 3mm ナイロンナット Nylon Nut 1 3mm 3x15mm 3x15mm A 使用するサーボに合わせる。 Set up according the servo you use. 使用する袋詰。 Part bags used. B 平行 Parallel 別購入品。 Must be purchased separately! 注意して組立てる所。 Pay close attention here! 41 プロポ Radio 2.6mm 2x8mm No.8 < サーボホーン > < Servo Horn > 171 171 169 H 168 サンワ, KO, JR SANWA(AIRTRONICS), KO, JR 167 H ハイテック HiTEC B 172 2.6x6x1mmカラーで高さを調整する。 Adjust the height with 2.6x6x1mm collar. 173 2.6x6x2mmカラーで高さを調整する。 Adjust the height with 2.6x6x2mm collar. A 170 166 F F フタバ Futaba A x1 Note the directions of 170and < ブレーキロッド > < Brake Rod> 175 使用するサーボに合わせる。 Set up according the servo you use. B 170と 171の向きに注意。 2.6x20mm < スロットルロッド > < Throttle Rod > 3x3mm 170 A C x2 3x3mm 183 E 180 0 178 176 177 C H D 使用するエンジンに合わせる。 Set up according the engine you use. 短い Short I 3x3mm 3x3mm 182 181 177 177 182 181 177 G 平行 Parallel H 10 15mm D 179 G .171 スロットルロッド Throttle Rod 2 x 8mm キャップビス Cap Screw I ブレーキロッド Brake Rod 1 1 2.6 x 20mm キャップビス Cap Screw 1 2.6mm 179 2 x 48mm アジャスターロッド Adjuster Rod ナイロンナット Nylon Nut 177 2mm ストッパー Stopper 181 リンケージスプリング Linkage Spring 178 スプリング Spring 1 2 3 x 3mm セットビス Set Screw 6 180 アジャスターノブ Adjuster Nob 2 183 2 x 68mm アジャスターロッド Adjuster Rod 1 2 使用する袋詰。 Part bags used. 可動するように組立てる。 Ensure smooth, non-binding movement when assembling. 仮止め。 Temporarily tighten. x2 2セット組立てる(例)。 Assemble as many times as specified. 4 向きに注意。 Note the direction. 別購入品。 Must be purchased separately! E 長い Long 20 42 スロットルリンケージ調整 Throttle Linkage Adjustment < ニュートラル > < Neutral> < ハイ> < High Throttle > < ブレーキ > < Brake> 1mm 1mm B 182 182 43 エアークリーナー Air Cleaner A 182 A ブレーキ調整つまみ Brake Adjusting Knobs B 1mm以下に閉じないようにスロー調整ビスで調整する。 Adjust with this screw the carburetor so it cannot close more than 1mm. 上側ーリヤ側 Upper Linkage - Rear Brake No.8 189 B 下側ーフロント側 Lower Linkage - Front Brake 3 x 10mm サラヘックスビス F/H Hex Screw 1 187 186 A 185 3x10mm 184 C D No.96176 HGエアークリーナー オイル(100cc) HG Air Cleaner Oil (100cc) 188 E 44 A オイルをしみ込ませておく。 Soak inner sponge with oil. C 短い Short D エアークリーナー Air Cleaner 使用する袋詰。 Part bags used. 別購入品。 Must be purchased separately! 長い Long B ホコリの多い場所で走行する時には 189を 186の上にかぶせる。 When running the engine in a dusty environment, cover with . 189 186 E キット付属のHGエアークリーナー専用です。 Specially for the HG Air Cleaner included in the kit. 45 ダンパー Shock No.9 196 カラー(厚) Collar (Thick) 4 197 カラー(薄) Collar (Thin) 4 195 3.5mm Oリング O-ring 2.6mm 2.6mm ワッシャー Washer 46 ダンパー Shock 199 198 197 195 196 195 191 197 196 B 190 191 195 4 C 198 B 190 (短) – フロント用 190 (Short) – For Front A C 191 (長) – リヤ用 191 (Long) – For Rear フロント用 For front x2 リヤ用 For rear x2 溝にはめる。 Fit into groove. No.9 201 B A ピストンを下げる。 Pull down the piston. B 多少もり上がるぐらいまで 入れる。 Fill in until shock oil nearly overflows. C 上下させ、気泡をとる。 Then, gently move the piston up and down to get rid of air bubbles. D 190 193 (長) – リヤ用 193 (Long) – For Rear (短) – フロント用 192 (Short) – For Front 193 4 4 8 192 194 192 193 194 ピストン(黒) Piston (Black) 199 6.8mm ボールエンド(S) Ball End (S) 198 Cリング C-ring 4 A 192 2.6mm 2.6mm ナイロンナット Nylon Nut 4 ダンパー オイル Shock Oil 200 D C A x4 スムーズに動くか確認する。 Check if piston moves smoothly. 47 ダンパー Shock No.9 207 A B 206 202 208 6.8mm A ボール Ball 208 4 サイズに合わせてカットする。 Cut according to size length. 使用する袋詰。 Part bags used. 204 203 B スプリング調整用。 For Spring adjustment. 向きに注意。 Note the direction. x2 C 204 2セット組立てる (例) 。 Assemble as many times as specified. (短) – フロント用 204 (Short) – For Front をカットする。 Cut off shaded portion. 205 C 205 (長) – リヤ用 205 (Long) – For Rear フロント用 For front x2 リヤ用 For rear x2 別購入品。 Must be purchased separately! 48 フロントダンパー Front Shock No.4,9 A 取付穴。 Holes for mounting. A 取付穴。 Holes for mounting. 3mm ナイロンナット Nylon Nut 2 210 フロントダンパー Front Shocks 3 x 5mm セットビス(銀) Set Screw (Silver) 2 3mm 210 5mm ダンパーブッシュ Shock Bushing 2 209 3 x 26mm シャフト Shaft 2 209 3x5mm A 49 リヤダンパー Rear Shock No.2,9 3mm ナイロンナット Nylon Nut 2 3 x 5mm セットビス(銀) Set Screw (Silver) 2 210 リヤダンパー Rear Shocks 3mm 210 5mm ダンパーブッシュ Shock Bushing 2 209 3 x 26mm シャフト Shaft 2 209 3x5mm A 使用する袋詰。 Part bags used. 左右同じように組立てる。 Assemble left and right sides the same way. 可動するように組立てる。 Ensure smooth, non-binding movement when assembling. 注意して組立てる所。 Pay close attention here! 50 その他 Other タイヤ Wheels D 1 212 A 5 C 7 3 4 8 B 6 2 A ホイルのミゾにピッタリ タイヤをおしこむ。 Slide the tires into these slots in the wheels. 51 x4 213 211 B はまりが悪い場合は 斜線部をカットする。 If doesn't fit cleanly, trim area with slanting lines. C あらかじめシンナー等で 接着面をきれいにしておく。 Clean the tire rims with thinner beforehand. D 番号順にタイヤを手で押さえ、瞬間 接着剤を少しづつ流しこみ、最後に 全体を接着する。 Apply instant glue little by little in the order. No.4 その他 Other タイヤ Wheels < フロント > < Front> 214 外側 Outside 内側 Inside < リヤ> < Rear > 214 ホイールストッパーナット Wheel Stopper Nut 4 214 使用する袋詰。 Part bags used. x4 番号の順に組立てる。 Assemble in the specified order. 4セット組立てる(例)。 Assemble as many times as specified. グリスを塗る。 Apply grease. をカットする。 Cut off shaded portion. 左右同じように組立てる。 Assemble left and right sides the same way. 向きに注意。 Note the direction. 瞬間接着剤で接着する。 Apply instant glue (CA glue, super glue). 52 215 ボディ Body Shell 8mm 8mm A B C A 排気口に合わせる。 Fit to the muffler when cutting out. 53 B 使用するエンジンに合わせる。 Fit to the engine when cutting out. C アンテナパイプ用。 Hole for antenna pipe. 塗装 Painting 1 塗装前に、洗剤で油やよごれを洗う。 2 ウインドウ部分に、内側から 3 塗分けはパッケージ写真も 4 塗装後、ボディ表面の保護ビニール Before painting, use a neutral detergent to remove any oil residues and dirt. 参考にしてください。 Refer to the pictures on the box for the color scheme. シートをはがしておく。 After painting, remove the protective film from the body shell. A A 京商スプレーカラーで ボディ内側を塗装する。 Paint the body shell from the inside using Kyosho’s spray colors. 54 デカール Decals デカールは好みの位置 に貼ってください。 Apply decals to any spots you like. をカットする。 Cut off shaded portion. マスキングシートを貼る。 Mask the windows from the inside. 8mm の穴をあける(例)。 8mm Drill holes with the specified diameter. 55 その他 Other ボディ Body Shell 216 マジックファスナー Velcro 216 マジックファスナー Velcro 56 No.8 ボディ Body Shell 3x12mm その他 Other 217 217 219 218 219 3mm 3mm 216 マジックファスナー Velcro 3 x 12mm サラヘックスビス F/H Hex Screw 2 3mm ナイロンナット Nylon Nut 2 使用する袋詰。 Part bags used. A 219 ボディピン Body Pin 2 左右同じように組立てる。 Assemble left and right sides the same way. A ボディピンは、図のように曲げておくと取り外しが楽です。 Slightly bend the body pins as shown in the diagram for easier removal. 取扱いの注意 OPERATING YOUR MODEL SAFELY 次のような時、場所では走らせない。思わぬ事故の原因になります。 WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) 警告 ●周囲に人がいなくて、広い安全な場所で! 1. 自動車道路では走らせない。 2. 近くに小さな子供がいたり、人の多い場所では走らせない。 3. 民家の近くや公園などでは走らせない。 4. 室内やせまいところでは走らせない。 ※人にケガをさせる原因になります。また、物をこわしたり、 他人の迷惑になります。 Operate the model in spacious areas with no people around! Do NOT operate it: 1. on roads! 2. in places where children and many people gather! 3. in residential districts and parks! 4. indoors and in limited space! * Non-observance may account for personal injury and property damage! ●プロポ関係の電池残量は常にチェックする。 電池が減ってくると電波の送・受信が弱くコントロール ができなくなり、暴走や衝突の原因なります。 Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! ●近くで無線操縦模型を楽しんでいる人がいる。 同じバンドでの同時走行はできません。電波が混信して コントロールができなくなり、暴走や衝突の原因なります。 Keep in mind that people around you may also operate a radio controled model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. This may lead to accidents! 01 05 ●車の動きがおかしい??とき。 すぐに走行を中止しておかしい原因を調べる、原因不明のまま 走行させると、思わぬ故障や事故の原因になります。 When the model is behaving strangely . . .! Immediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! 事故やケガ等の危険防止のため、次のことを必ずお守りください。 WARNING: in order to avoid accidents and personal injury, 警告 be sure to observe the following: ●燃料の取扱いは、必ず屋外で。 ●燃料は、模型用グロー燃料を必ず使用する。 燃料の蒸気、排気ガスは有害です。 ガソリンや灯油の使用は、火災等の事故の原因になります。 Handle fuel ONLY outdoors! ONLY use glow fuel for radio control models! Vapors and exhausts are very noxious to health! ●回転している部分に、指や物などを入れない。 高速回転しているのでケガの原因になります。 Do NOT put fingers or any objects inside rotating and moving parts! Rotating / moving at high speed, you may be seriously injured! Because the use of gasoline and kerosene in R/C models accounts for fires, do NOT use them! ●燃料は、引火性があります。 1. 火気のあるところや室内では絶対に使用しない。 2. 保管は、キャップをしっかりしめ、幼児の手の届かない冷暗 所に置くこと。 3. 使用後の空缶は、火中には投げ入れない。爆発の原因になり ます。 Fuel is highly inflammable and high-explosive! 1. NEVER use fuel indoors or in places with open fires and sources of heat! 2. Store fuel ONLY in cool, dry and dark places out of children's reach! Tightly shut the cap! 3. Do NOT dispose of empty fuel cans into a fire! There is danger of explosion! ●燃料は、飲んだり、目に入れたりしない。 ●走行直後は、エンジン、マフラー周辺は高温になって いるので、すぐにはさわらない。 ヤケドの原因になります。 Right after use, do NOT touch equipment on the model such as the engine and muffler, because they generate high temperatures! You may burn yourself seriously touching them! 万一、事故が起きた場合は、吐かせる、洗眼する等をした後、 すぐに医師の診察を受けてください。 NEITHER swallow fuel NOR let it into your eyes! Immediate measures should be taken: if fuel is swallowed, induce vomiting. If fuel gets into eyes, rinse them and consult an orphamologist! <EXPLODED VIEW> 177 163 164 165 IF435 J 一部パーツ販売していないパーツがあります。 Parts indentified only by key numbers are not sold individually! 152 IF450 169 IF419-R 67 IF428 I 83 IF427 180 IF454 A 160 IF451 C フロントダンパー Front Shock 160 IF451 H 18 IF408 57 IF408 91 IF459-2.5 73 IF428 120 W0202H 64 IF442 71 IF425-29.5 118 IF332 68 IF428 IF35 53 92653H 54 W5015 52 W0201H 112 107 IF417 162 IF462H 189 IF345-1 114 IF445 111 IF35 111 86 IF421 126 IFW53 124 IFW54B 109 BRG022 / 127 IFW339 129 96774 109 BRG022 / 38 IFW107GM 37 IFW107GM 133 IFW35 IF418 110 IF418 130 BRG001 F 87 IF442 H M IF444-01 リヤダンパー Rear Shock 212 AKA34001M 138 IF444 / 140 IF451 141 IF444 / IF444-01 Q / AKA14001M 139 IF451 51 IF465H R 2 BRG005 45 IF442 31 IF422 46 IF426-68.5 90 IF427 37 IFW107GM 96773 2 BRG005 35 IF424 34 IF423 34 IF423 212 AKA34001M / AKA14001M 135 92511 211 IFH003BK / KY / W 214 IFW336GM © Copyright 2008 KYOSHO CORPORATION 214 IFW336GM 209 IF341 47 IF442 213 AKA14001M フロントダンパー Front Shock 32 IF422 P 144 IF449 40 IF452 38 IF107GM 33 IF423 A 84 IF425-35 KY / W 36 IF456 39 IF452 58 IF448 E IF425-35 211 IFH003BK / 50 IF428 IF444-01 K 213 AKA14001M 48 IFW124 138 IF444 / 209 IF341 210 IF346-07 52 W0201H O IF431 R 53 92653H 54 W5015 Q 137 IF444 IF431 L 55 LA43 19 BRG031 49 IF428 134 IF431 146 IF449 G F S 44 IF434 16 IF407-13 128 IF430 125 96641 / IFW339 134 IF431 120 W0202H 118 IF332 24 IF346-04 19 BRG031 143 92213 128 IF430 57 IF408 リヤデフ Rear Diff. 17 IF408 22 IF441 121 IFW143 132 IFW35 108 IF417 117 IF332 18 IF408 23 IF429 21 IF458 123 IF432 122 IFW143 131 IFW46 IF418 IF418 G 28 IF429 57 IF408 210 IF346-07 78 IF466 185 109 BRG022 / 79 IF438 77 IFW332-01 56 IF460-2.8 P 107 IF417 43 IF463H M 186 110 IF418 96773 95 IF405 98 IF415 188 162 IF462H 113 IF446 81 IF419 / IF419-L 75 IF420 77 IFW332-01 2 BRG005 センターデフ Center Diff. N O 59 IF433 96 IF405 94 IF405 78 IF466 L 93 IF405 60 IF433 187 116 IF433 55 LA43 1188 119 IF461H 118 IF332 N IF345 112 75 IF420 85 IF426-64.5 97 IF416 219 97002 161 97008-36H 1188 219 97002 97 IF416 62 IF440 115 IF453 D 29 IF429 99 IFW324-01 25 IF429 99 IFW324-01 184 2 BRG005 82 IF421 105 IF414 97 IF416 55 LA43 118 IF332 B 61 IF457 26 IF437 97 IF416 98 IF415 100 IF414 109 BRG022 / 27 IF429 105 IF414 K フロントデフ Front Diff. IF418 117 IF332 79 IF438 119 IF461H 36 IF456 148 IF450 63 IF434 E 30 IF429 リヤダンパー Rear Shock 101 IF414 16 IF407-13 55 LA43 104 IF443 177 19 BRG031 89 IF439 C 147 IF453 IF454 17 IF408 30 IF429 39B IF452 143 92213 19 BRG031 B 88 IF442 181 142 1876 143 92213 92638 102 IF414 182 IF453 155 IF450 / 92638 I 155 IF450 / 177 157 IF453 24 IF346-04 72 IF442 70 IF428 66 IFW123 69 IF464H 182 181 210 IF346-07 24 IF346-04 106 1876 / IF454 183 156 IF447 65 IF436 KY / W 42 IF423 149 IF351 175 176 IF454 180 170 IF454 218 IF401BK / 209 IF341 IF450 150 IF450 103 IF414 210 IF346-07 92 IF409 183 J 158 IF451 209 IF341 153 177 166 167 168 IF435 159 IF466 80 IF421 179 159 IF466 IF450 154 171 172 173 76 IF419 / 217 IF455 1708 IF454 178 IF454 D 41 IF422 151 IF450 / 禁無断転載複製 145 IF449 S 136 92511 INFERNO MP9 TEAM KYOSHO INTERNATIONAL < EXPLODED VIEW > デフギヤ Gear Differential 6 IF402 5 IF402 4 ORG06 12 IF406-43 3 IF412 2 BRG005 1 < フロント/リヤ用 > < For front and rear > 2 BRG005 4 ORG06 20 96772 6 IF402 IF403 9 IF402 13 5 IF402 3 IF412 7 IF411 8 IF402 6 IF402 5 IF402 4 ORG06 2 BRG005 14 IF410-46 11 IF413 10 < センター用 > < For center> 4 ORG06 IF404 2 BRG005 6 IF402 15 9 IF402 11 IF413 ダンパー Shock 7 IF411 8 IF402 200 IF346-02 201 IF346-03 IF349 IFW IF346-06 206 206 200 IF346-02 206 -06 195 201 IF346-03 206 206 196 195 197 203 IF346-05 204 IF350-916 193 IF337 IF3 ※1 46- IF346-06 202 IF346-08 198 IF337/1185 -06 196 05 IFW140-05 194 IF347-128 ※ 2 195 (Velvet coat) / IF349-01 (ノーマルコート) (Normal coat) 46- IF337/1177 140 192 IFW140-02 ※1 190 IF349-01V (ベルベットコート) IF3 206 < フロント用 > < For front> IFW140-02/1177 194 IF347-128 ※ 2 IFW140-02/1185 140 IFW 5 IF402 195 IFW140-05 197 191 IF346-01V (ベルベットコート) 05 IF346-05 198 208 IFW140-05 (スタンダード) 202 IF346-08 203 IF346-05 IF346 < リヤ用> < For rear> ※ 1 IF349 / IF346のビッグダンパーセットS / Lに含まれる 190 / 191のダンパーケースはそれぞれノーマルコーテ ィングです。 (本キット標準はベルベットコートです。) 190& 191shock cases included in IF349 & IF346 shock sets (S & L) have normal coating. (Kit includes velvet coated versions.) (Standard) / W0204(ハードアルマイト) (Hard Anodized) ※ 3 ※ 2 IF349 / IF346のビッグダンパーセットS / Lに含まれる 194ダンパーピストンはIF347-136(1.3mmx6穴)です。 本キット標準の1.2mmx8穴は別途IF347-128をお買い 求めください。 Shock piston 194included in IF349 & IF346 Shock Set (S & L), is the IF347-346 (1.3mm x 6-hole). For the 1.2mm x 8-hole item included in this kit, purchase IF347-128. 205 IF348-1216 IF346-05 207 199 (Velvet coat) / IF346-01 (ノーマルコート) (Normal coat) 207 199 208 ※ 3 IF349 / IF346のビッグダンパーセットS / Lに含まれる 208 6.8mmボールはスタンダードタイプです。 IFW140-05 (スタンダード) (本キット標準はハードアルマイトです。) 208 6.8mm ball included in IF349 & IF346 Big Shock Set (Standard) / W0204(ハードアルマイト) (S & L) is the standard type. (Hard Anodized) ※ 3 (This kit includes hard anodized balls). スペアパーツ(1) SPARE PARTS (1) 品番 No. AKA14001 M AKA34001 M BRG001 BRG005 BRG022 BRG031 IF35 IF332 IF337 IF341 IF345 IF345 -1 IF346 IF346 -01 IF346 -01V IF346 -02 IF346 -03 IF346 -04 IF346 -05 IF346 -06 IF346 -07 IF346 -08 IF347 -128 IF348 -1216 IF349 パーツ名 Part Names 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 1 / 8 バギー I-Beam(ミディアム / 2 入)インナー付 212 213 x 2 AKA 1 / 8 バギー用モールドインナー(ミディアム / 2 入) 1/8 Buggy I-Beam (Medium / 2-pcs) with inners AKA Molded Inners for 1/8 Buggy (Medium / 2-pcs) シールドベアリング(5x10x4)4 入 Shield Bearing (5x10x4 / 4pcs) シールドベアリング(8x16x5)2 入 Shield Bearing (8x16x5 / 2pcs) シールドベアリング(6x10x3)2 入 Shield Bearing (6x10x3 / 2pcs) シールドベアリング(5x11x4)2 入 Shield Bearing (5x11x4 / 2pcs) ステアリングピン Steering Pin タイロッド Tie Rod ダンパーシャフト(L=66mm) Shock Shaft (L=66mm) 6.5x26mm シャフト 6.5x26mm Shaft HG エアクリーナー HG Air Cleaner HG エアクリーナースポンジ HG Air Cleaner Sponge ビッグダンパーセット L Big Shock Set L 品番 No. 212 x 2 210 一律 1050 (税込) IF412 130 x 4 1050 IF413 2520 IF411 2 x2 683 IF414 109 x 2 1050 IF415 19 x 2 1050 IF416 473 IF417 1260 IF418 111 112 x 2 117 x 2 193 x 2 118 x 4 2.6mm ワッシャー / ナイロンナット x 2 2.6mm Washer / Nylon Nut 209 x 4 945 945 184 185 186 187 188 189 x 1 189 x 2 1365 IF419 IF419 -L IF419 -R 1365 IF420 6720 IF421 ビッグダンパーケース(L / L=61 / 2pcs) 191 x 2 Big Shock Case (L / L=61 / 2pcs) 3675 IF422 ベルベットコートビッグダンパーケース(L / L=61 / 2pcs) Velvet Coating Big Shock Case (L / L=61 / 2pcs) 191 x 2 4200 200 x 4 1890 201 x 4 420 キャップビス 24 x 4 3x22mm 3x22mm Cap Screw x 4 945 ダンパーキャップ Shock Cap ダイアフラム Diaphragm スチールダンパーブッシュ(ビックダンパー用) 191 193 194 196 197 198 199 200 201 202 203 207 208 x 2 206 一式 195 x 4 206 One set Steel Shock Bushing (for Big Shock) ダンパーエンドセット 196 Shock End Set スプリングアジャストカラー 206 Spring Adjust Collar 206 ダンパーキャップブッシュセット 210 Shock Cap Bushing Set ダンパーブーツ 202 Shock Boots ダンパーピストン(1.2x8 穴) 194 Shock Piston (1.2x8 Hole) ビッグダンパースプリング ( L パープル) 205 Big Shock Spring L (Purple) ビッグダンパーセット S 190 Big Shock Set S 200 197 199 203 207 x 4 一式(ダンパー 4 本分) One set (for 4 shocks) x4 630 630 420 x4 840 x2 525 x2 192 194 196 201 202 203 206 195 x 4 206 197 198 199 207 208 x 2 一式 One set IF423 IF424 IF425 -29.5 IF425 -35 IF426 -64.5 IF426 -68.5 IF427 1260 IF428 6090 IF429 IF430 IF349 -01 IF349 -01V IF350 -916 ビッグダンパーケース(S / L=47 / 2pcs) 190 x 2 Big Shock Case (S / L=47 / 2pcs) 3150 IF431 ベルベットコートビッグダンパーケース(S / L=47 / 2pcs) Velvet Coating Big Shock Case (S / L=47 / 2pcs) 190 x 2 3675 IF432 204 x 2 1155 IF433 IF351 149 x 1 525 IF434 218 x 1 1155 IF435 578 IF436 1 13 x 1 578 IF437 10 15 x 1 630 IF438 IF401 BK IF402 IF403 IF404 IF405 IF406 -43 IF407 -13 IF408 IF409 IF410 -46 ビッグダンパースプリング ( S パープル) Big Shock Spring S (Purple) シリコンスイッチブーツ Silicone Switch Boots ウイング(ブラック / MP9) Wing (Black/MP9) デフベベルギヤセット(MP9) Diff. Bevel Gear Set (MP9) デフケースセット(F&R / MP9) Diff. Case Set (F&R / MP9) センターデフケースセット(MP9) Center Diff. Case Set (MP9) センターデフマウント(MP9) Center Diff. Mount (MP9) リングギヤ(43T / MP9) Ring Gear (43T / MP9) ドライブベベルギヤ(13T / MP9) Drive Bevel Gear (13T / MP9) バルクヘッドセット(F&R / MP9) Bulk Head Set (F&R / MP9) バンパー(MP9) Bumper (MP9) スパーギヤ(46T / MP9) Spur Gear (46T / MP9) 5 6 x2 8 9 x4 93 94 95 96 x 1 12 x 1 20 x 2 16 x 1 17 18 x 1 57 x 2 パーツ名 Part Names デフベベルシャフト(2pcs / MP9) Diff. Bevel Shaft (2pcs / MP9) デフシャフト(2pcs / MP9) Diff. Shaft (2pcs / MP9) センターデフシャフト(2pcs / MP9) Center Diff. Shaft (2pcs / MP9) ブレーキカムセット(MP9) Brake Cam Set (MP9) ブレーキローター(30mm / MP9) Brake Rotor (30mm / MP9) ブレーキパッド (MP9) Brake Pad (MP9) サーボセイバーアッセンブリー(MP9) Servo Saver Assy (MP9) サーボセイバーポスト(MP9) Servo Saver Post (MP9) ★ FOR JAPANESE MARKET ONLY. 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 210 一律 998 (税込) 7 x2 315 3 x2 11 x 2 1050 100 101 102 103 x 1 105 x 2 788 98 x 1 2100 97 x 2 1785 107 108 x 1 1995 109 x 4 1785 110 x 2 アルミナックルアーム(L, R / ガンメタリック / MP9) 76 81 x 1 Aluminum Knuckle Arm (L,R / Gunmetal / MP9) アルミナックルアーム(L / ガンメタリック / MP9) 81 x 1 Aluminum Knuckle Arm (L / Gunmetal / MP9) アルミナックルアーム(R / ガンメタリック / MP9) 76 x 1 Aluminum Knuckle Arm (R / Gunmetal / MP9) 77 x 4 ナックルアームカラー(4pcs / MP9) 75 x 4 Knuckle Arm Collar (4pcs / MP9) フロントハブキャリア(MP9) 80 82 x 1 86 x 2 Front Hub Carrier (MP9) セッティング用ブッシュ付 for Setting with Bushing リヤハブキャリア(MP9) 31 41 x 1 32 x 2 Rear Hub Carrier (MP9) セッティング用プラカラー付 for Setting with Plastic Collar リヤロアサスアーム(L, R / MP9) 33 42 x 1 34 x 4 Rear Lower Sus. Arm (L, R / MP9) セッティング用ブッシュ付 for Setting with Bushing 3mm ナイロンナット x2 3mm Nylon Nut 9975 5040 5040 578 1260 630 945 サスシャフト(3.5x49mm / 2pcs / MP9) 35 x 2 サスシャフト(3x29.5mm / 2pcs / MP9) 71 x 2 420 サスシャフト(3x35mm / 2pcs / MP9) 84 x 2 473 サスシャフト(4x64.5mm / 2pcs / MP9) 85 x 2 630 サスシャフト(4x68.5mm / 2pcs / MP9) 46 x 2 630 83 90 x 1 945 Sus. Shaft (3.5x49mm / 2pcs / MP9) Sus. Shaft (3x29.5mm / 2pcs / MP9) Sus. Shaft (3x35mm / 2pcs / MP9) Sus. Shaft (4x64.5mm / 2pcs / MP9) Sus. Shaft (4x68.5mm / 2pcs / MP9) フロントロアサスアーム(L, R / MP9) Front Lower Sus. Arm (L, R / MP9) アッパーアームセット(MP9) Upper Arm Set (MP9) ウイングステーセット(MP9) Wing Stay Set (MP9) エンジンマウント(MP9) Engine Mount (MP9) エンジンマウントプレート(ガンメタリック / MP9) Engine Mount Plate (Gunmetal / MP9) 3PC フライホイール(32mm / MP9) 3PC Flywheel (32mm / MP9) トルクロッドセット(MP9) Chassis Brace Set (MP9) サスホルダーセット(MP9) Sus. Holder Set (MP9) サーボホーンセット(MP9) Servo Horn Set (MP9) ハードフロントダンパーステー(MP9) Hard Front Shock Stay (MP9) ハードリヤダンパーステー(MP9) Hard Rear Shock Stay (MP9) キングピン(M4 / 4pcs / MP9) King Pin (M4 / 4pcs / MP9) 49 73 23 29 50 68 x 2 67 70 x 1 x4 25 27 28 x 1 x 4 30 x 2 128 x 2 134 x 2 4x8mm フランジ付キャップビス x 4 4x8mm Flanged Cap Screw 123 x 1 683 840 525 3675 1155 1575 60 116 x 1 59 x 4 630 44 63 x 1 630 163 164 165 166 167 168 x 1 420 65 x 1 6090 26 x 1 6300 79 x 4 525 IF439 フロントロアサスホルダー( F/ ガンメタリック / MP9) 89 x 1 2100 2625 IF440 フロントロアサスホルダー(R / ガンメタリック / MP9) 62 x 1 2100 1365 IF441 630 735 92 x 1 420 14 x 1 2310 IF442 IF443 Front Lower Sus. Holder (F / Gunmetal / MP9) Front Lower Sus. Holder (R / Gunmetal / MP9) リヤロアサスホルダー(F / ガンメタリック / MP9) 22 x 1 Rear Lower Sus Holder (F / Gunmetal / MP9) サスブッシュセット(MP9) 45 45B 47 64 x2 Sus. Bush Set (MP9) 72 78 88 88B 各種セッティング用ブッシュ付 Bushings for setting センターデフプレート(ガンメタリック / MP9) Center Diff. Plate (Gunmetal / MP9) 104 x 1 2100 525 840 スペアパーツ(2) SPARE PARTS (2) 品番 No. IF444 IF444 -01 IF445 IF446 IF447 IF448 IF449 IF450 IF451 IF452 IF453 IF454 IF455 IF456 IF457 IF458 IF459 -2.5 IF460 -2.8 IF461 H IF462 H IF463 H IF464 H IF465 H IF466 IFB002 IFD401 IFH003 BK IFW35 パーツ名 内容(キー No. と入数) ★定価 ★発送 Part Names Quantity (税込)手数料 燃料タンクセット(MP9) 137 x 1 138 141 x 2 1890 210 Fuel Tank Set (MP9) 一律 燃料タンクブッシュセット(MP9) 138 141 x 2 (税込) 263 Fuel Tank Bush Set (MP9) 品番 No. IFW46 IFW53 フロントアッパープレート(ガンメタリック / MP9) 114 x 1 840 ステアリングプレート(ガンメタリック / MP9) 113 x 1 2520 IFW54 B IFW107 GM 156 x 1 840 IFW123 58 x 1 12600 IFW124 Front Upper Plate (Gunmetal / MP9) Steering Plate (Gunmetal / MP9) メカプレート(ガンメタリック / MP9) Radio Plate (Gunmetal / MP9) ハードメインシャシー(MP9) Hard Main Chassis (MP9) サイドガード(MP9) Side Guard (MP9) メカボックスセット(MP9) Radio Box Set (MP9) ポストセット(MP9) Post Set (MP9) マッドガード(MP9) Mud Guard (MP9) ボディマウント Body Mount リンケージセット(MP9) Linkage Set (MP9) ウイングワッシャー(ガンメタリック / 2pcs / MP9) 144 145 146 x 1 1050 148 150 151 152 x 1 155 x 2 2x42mm ボタンヘックスビス x 1 2x42mm Button Hex Screw 2x6mm ボタンヘックスビス x 1 2x6mm Button Hex Screw 139 140 158 x 1 39 39B x 1 106 157 169 175 177 180 160 x 4 40 x 2 115 x 1 147 x 2 x4 170 171 172 173 176 178 179 x 1 x4 181 182 x 2 1260 IFW143 525 IFW324 -01 IFW332 -01 IFW336 GM 420 IFW339 1050 LA43 420 ORG006 217 x 2 315 36 x 2 Universal Swing Shaft (L=91/2pcs/MP9) フロントセンターユニバーサル 61 x 1 シャフト(L=84 / 1pc / MP9) Front Universal Shaft (L=84 / 1pc / MP9) 3885 リヤセンターユニバーサル シャフト(L=110 / 1pc / MP9) Rear Universal Shaft (L=110/1pc/MP9) 2310 Wing Washer (Gunmetal / 2pcs / MP9) ユニバーサルスイングシャフト(L=91 / 2pcs / MP9) 21 x 1 2205 フロントスタビライザーバー(2.5mm / 1pc / MP9) 91 x 1 473 リヤスタビライザーバー(2.8mm / 1pc / MP9) 56 x 1 525 6.8mm 座付ハードボール(2pcs / MP9) 6.8mm Flanged Hard Ball (2pcs / MP9) 5.8mm 座付ハードボール(2pcs / MP9) 5.8mm Flanged Hard Ball (2pcs / MP9) 7.8mm 座付ハードボール(2pcs / IF56) 7.8mm Flanged Hard Ball (2pcs / IF56) 6.8mm 座付ハードボール(2pcs / IF313) 6.8mm Flanged Hard Ball (2pcs / IF313) 119 x 2 420 162 x 2 420 43 x 2 525 69 x 2 525 51 x 2 420 Front Sway Bar (2.5mm/1pc/MP9) Rear Sway Bar (2.8mm / 1pc / MP9) 7.8mm ツバ付ハードボール(2pcs / 2pcs / IF55) 7.8mm Taper Hard Ball (2pcs / 2pcs / IF55) センターデフ&サーボマウントスペーサーセット Center Diff. & Servo Mount Spacer Set ボディセット(MP9) Body Set (MP9) デカール(MP9) Decal Set (MP9) ホイール(4pcs / ブラック / MP9) Wheel (4pcs / Black / MP9) ベルガイドワッシャー Bell Guide Washer 78 159 x 2 420 未塗装のクリヤボディセット(MP9) Unpainted clear body set (MP9) MP9 ロゴデカールのセット MP9 logo decal set 3150 211 x 4 1470 132 133 x 2 IFW140 -02 IFW140 -05 1260 315 ★ FOR JAPANESE MARKET ONLY. パーツ名 内容(キー No. と入数) ★定価 ★発送 Part Names Quantity (税込)手数料 SP クラッチベル (13T) 131 x 1 2310 210 SP Clutch Bell (13T) 一律 3PC クラッチスプリング(1.00) 126 x 3 420 (税込) 3PC Clutch Spring (1.00) 3PC フライホイールナット SG シャフト 124 x 1 420 3PC Flywheel Nut SG Shaft ホイ−ルハブ(ガンメタリック / 4pcs) 37 x 4 1155 Wheel Hub (Gunmetal / 4pcs) SP ハードアッパーロッド(フロント) 66 x 2 1050 SP Hard Upper Rod (Front) SP ハードアッパーロッド(リヤ) 48 x 2 1260 SP Hard Upper Rod (Rear) ダンパーシャフト(L=53mm) 2.6mm ワッシャー / ナイロンナット x 2 840 Shock Shaft (L=53mm) 192 x 2 2.6mm Washer / Nylon Nut 195 198 x 4 O リングセット 840 O-ring Set 196 197 208 x 2 テーパーコレットセット 121 122 x 1 473 Tapered Collet Set ブレーキプレートボルト 99 x 4 420 Brake Plate Bolt ブッシュ(アルミナックルアーム用) 525 Bushing (For Aluminum Knuckle Arm) 77 x 4 ナイロン付ホイールナット(ガンメタリック) 1260 Wheel Nut With Nylon (Gunmetal) 214 x 4 3PC HD アルミクラッチシュー 125 127 x 3 1680 3PC HD Aluminum Clutch Shoe 5.8mm ボールエンド 55 x 12 315 5.8mm Ball End O リング (P6) 4 x 15 420 O-ring (P6) 5.8mm ハードボール(5pcs) 52 x 5 735 5.8mm Hard Ball (5pcs) W0201 H W0202 6.8mm ハードボール(5pcs) 6.8mm Hard Ball (5pcs) H 6.8mm ハードボール(H=4.8/4pcs) W0204 6.8mm Hard Ball (H=4.8/4pcs) 5.8mm ダンパーエンド W5015 5.8mm Shock End カラーアンテナ (黒) 1708 Color Antenna (Black) 燃料フィルター 1876 Fuel Filter 燃料チューブ(2.4x6x1m) 92213 Fuel Tube (24x6x1m) マフラーステー 92511 Muffler Stay スナップピン 92638 Snap Pin 92653 5.8mm ハードボールジョイント(3.0 穴 / 4pcs) H 5.8mm Hard Ball Joint (3.0 hole / 4pcs) HG エアークリーナーオイル(100cc) 96176 HG Air Cleaner Oil (100cc) 3x5x0.1mm シム 96641 3x5x0.1mm Shim 13x16x0.15mm シム 96772 13x16x0.15mm Shim 8x12x0.2mm シム 96773 8x12x0.2mm Shim 5x20x0.2mm シム 96774 5x20x0.2mm Shim ボディピン (1.6mm) 97002 Body Pin (1.6mm) 97008 ハードアジャストロッド(3x36mm / 2pcs) -36H Hard Adjust Rod (3x36mm / 2pcs) 120 x 5 735 208 x 4 735 54 x 4 210 153 154 x 4 525 106 142 x 1 1050 143 x 1m 735 135 136 x 1 630 155 x 10 210 53 x 4 945 HG エアークリーナー専用オイル Oil for HG air cleaner 1470 125 x 10 473 20 x 10 473 5 枚入り 5pcs. 210 129 x 5 315 219 x 10 263 161 x 2 998 キットの部品の一部にはスペアパーツとして販売していない物があります。 京商ではオプションパーツを販売していますのでお買い求めください。 Some of the parts included are not available as spare parts. Purchase optional parts instead. オプションパーツ 品番 No. AKA14001 H AKA14001 S AKA14001 HPW AKA14001 MPW AKA14001 SPW AKA14002 H AKA14002 M AKA14002 S AKA14002 HPW AKA14002 MPW AKA14002 SPW AKA24001 W IF347 -126 IF347 -135 IF347 -136 IF347 -138 IF347 -145 IF348 -916 IF348 -1016 IF348 -1116 IF348 -1316 IF350 -716 IF350 -816 IF350 -1016 IF401 KY IF401 W IF410 -48 IF459 -2.3 パーツ名 Part Names 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 1 / 8 バギー I-Beam(ハード / 2 入)インナー付 AKA タイヤ / インナースポンジのセット 1 / 8 バギー I-Beam(ソフト / 2 入)インナー付 AKA タイヤ / インナースポンジのセット 1:8 Buggy I-Beam Hard 1:8 Buggy I-Beam Soft AKA Tire / Inner Sponge Set AKA Tire / Inner Sponge Set 1 / 8 バギー I-Beam ホイール接着済(ハード / 2 入) ホイール接着済 AKA タイヤのセット 1:8 Buggy I-Beam Hard Pre-Mounted Pre-glued AKA tires and wheel set 1 / 8 バギー I-Beam ホイール接着済(ミディアム / 2 入) ホイール接着済 AKA タイヤのセット 1:8 Buggy I-Beam Medium Pre-Mounted Pre-glued AKA tires and wheel set 1 / 8 バギー I-Beam ホイール接着済(ソフト / 2 入) ホイール接着済 AKA タイヤのセット 1:8 Buggy I-Beam Soft Pre-Mounted Pre-glued AKA tires and wheel set 1 / 8 バギー City Block(ハード / 2 入)インナー付 AKA タイヤ / インナースポンジのセット 1 / 8 バギー City Block(ミディアム / 2 入)インナー付 AKA タイヤ / インナースポンジのセット 1 / 8 バギー City Block(ソフト / 2 入)インナー付 AKA タイヤ / インナースポンジのセット 1:8 Buggy City Block Hard 1:8 Buggy City Block Medium 1:8 Buggy City Block Soft AKA Tire / Inner Sponge Set AKA Tire / Inner Sponge Set AKA Tire / Inner Sponge Set 1 / 8 バギー City Block ホイール接着済(ハード / 2 入) ホイール接着済 AKA タイヤのセット 1:8 Buggy City Block Hard Pre-Mounted Pre-glued AKA tires and wheel set 1 / 8 バギー City Block ホイール接着済(ミディアム / 2 入) ホイール接着済 AKA タイヤのセット 1:8 Buggy City Block Medium Pre-Mounted Pre-glued AKA tires and wheel set 1 / 8 バギー City Block ホイール接着済(ソフト / 2 入) ホイール接着済 AKA タイヤのセット 1:8 Buggy City Block Soft Pre-Mounted Pre-glued AKA tires and wheel set AKA 1 / 8 バギー用ホイール(ホワイト / 4 入) AKA ホイールのセット 1:8 Buggy Wheels (4 pcs.) AKA wheel set ダンパーピストン(1.2x6 穴) 194と交換 ダンパーセッティング用 Shock Piston (1.2x6 Hole) instead of 194. For Shock setting ダンパーピストン(1.3x5 穴) 194と交換 ダンパーセッティング用 Shock Piston (1.3x5 Hole) instead of 194. For Shock setting ダンパーピストン(1.3x6 穴) 194と交換 ダンパーセッティング用 Shock Piston (1.3x6 Hole) instead of 194. For Shock setting ダンパーピストン(1.3x8 穴) 194と交換 ダンパーセッティング用 Shock Piston (1.3x8 Hole) instead of 194. For Shock setting ダンパーピストン(1.4x5 穴) 194と交換 ダンパーセッティング用 Shock Piston (1.4x5 Hole) instead of 194. For Shock setting ビッグダンパースプリング ( L レッド) 205と交換 ダンパーセッティング用 Big Shock Spring L (Red) instead of 205. For Shock setting ビッグダンパースプリング ( L ブルー) 205と交換 ダンパーセッティング用 Big Shock Spring L (Blue) instead of 205. For Shock setting ビッグダンパースプリング ( L ライトグリーン) 205と交換 ダンパーセッティング用 Big Shock Spring L (Light Green) instead of 205. For Shock setting ビッグダンパースプリング ( L ホワイト) 205と交換 ダンパーセッティング用 Big Shock Spring L (White) instead of 205. For Shock setting ビッグダンパースプリング ( S ブルー) 204と交換 ダンパーセッティング用 Big Shock Spring S (Blue) instead of 204. For Shock setting ビッグダンパースプリング ( S ライトグリーン) 204と交換 ダンパーセッティング用 Big Shock Spring S (Light Green) instead of 204. For Shock setting ビッグダンパースプリング ( S ホワイト) 204と交換 ダンパーセッティング用 Big Shock Spring S (White) instead of 204. For Shock setting ウィング(蛍光イエロー / MP9) 218と交換 Wing (Fluorescent Yellow / MP9) instead of 218. ウィング(ホワイト / MP9) 218と交換 instead of 218. Wing (White / MP9) スパーギヤ(48T / MP9) 14と交換 ギヤ比変更用 Spur Gear (48T / MP9) instead of 14. for changing the gear ratio フロントスタビライザーバー(2.3mm / 1pcs / MP9) 91 と交換 Front Sway Bar (2.3mm/1pcs/MP9) instead of 91. 210 一律 2520 (税込) 2520 3360 3360 3360 2520 2520 2520 3360 3360 パーツ名 Part Names AKA T シャツ(L) AKA Short Sleeve Black Shirt (L) AKA T シャツ(M) AKA Short Sleeve Black Shirt (M) AKA T シャツ(SM) AKA Short Sleeve Black Shirt (SM) AKA T シャツ(XL) AKA Short Sleeve Black Shirt (XL) AKA T シャツ(XXL) AKA Short Sleeve Black Shirt (XXL) AKA ロゴ入り T シャツ AKA ロゴ入り T シャツ T-Shirt With AKA Logo AKA ロゴ入り T シャツ T-Shirt With AKA Logo 1260 IFW136 525 525 525 1260 IFW336 BL IFW336 R 1260 IFW401 1260 1155 1155 1155 1155 1155 2310 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 91 と交換 473 210 instead of 91. 一律 91 と交換 473 (税込) instead of 91. 56 と交換 instead of 56 と交換 instead of 56 と交換 instead of 56 と交換 instead of 211と交換 instead of 211と交換 instead of 131と交換 instead of 131. 56. 525 56. 525 56. 525 56. 525 211. 1470 211. 1470 ギヤ比変更用 for changing the gear ratio 2310 127と交換 クラッチセッティング用 instead of 127. For Clutch setting 1680 Made of Carbon Fiber 3PC クラッチスプリング(1.10) 126と交換 クラッチセッティング用 3PC Clutch Spring (1.10) instead of 126. For Clutch setting 3PC クラッチスプリング(0.95) 126と交換 クラッチセッティング用 3PC Clutch Spring (0.95) instead of 126. For Clutch setting 3PC クラッチスプリング(0.90) 126と交換 クラッチセッティング用 3PC Clutch Spring (0.90) instead of 126. For Clutch setting ホイ−ルハブ(ブルー / 4pcs) 37 と交換 Wheel Hub (Blue / 4pcs) instead of 37. ホイ−ルハブ(ゴールド / 4pcs) 37 と交換 Wheel Hub (Gold / 4pcs) instead of 37. LSD ギヤ専用オイル LSD ギヤオイル For TCD Gear TCD Gear Oil 3PC アルミクラッチシュー 127と交換 3PC Aluminum Clutch Shoe instead of 127. ナイロン付ホイールナット(ブルー) 214と交換 Wheel Nut With Nylon (Blue) instead of 214. ナイロン付ホイールナット(レッド) 214と交換 Wheel Nut With Nylon (Red) instead of 214. SP アルミメカポスト 160と交換 アルミ削り出し (ガンメタリック / 4pcs / MP9) instead of 160. Aluminum SP Aluminum Radio Post (Gunmetal / 4pcs / MP9) アルミウィングステーカラー 29 と交換 IFW402 (ガンメタリック / 4pcs / MP9) instead of 29. Aluminum Wing Stay Collar (Gunmetal / 4pcs / MP9) LSD ギヤセット (MP9) IFW403 TCD Gear Set (MP9) LSD ギヤオイル 92201 TCD Gear Oil セッティングウェイト 96161 Setting Weight アルミ削り出し Aluminum フロント / リヤ / センターデフ用 420 420 420 1155 1155 525 1575 1260 1260 735 893 for Front / Rear / Center Diff. 8400 LSD ギヤ専用オイル 1260 For TCD Gear バランス取用ウェイト Weight for balance 504 473 ACCESSORY 品番 No. 210 一律 2310 (税込) AKA98102 2310 39081 2310 2310 AKA ロゴ入り T シャツ 2310 T-Shirt With AKA Logo ★ FOR JAPANESE MARKET ONLY. カーボン製 525 525 AKA ロゴ入り T シャツ T-Shirt With AKA Logo パーツ名 Part Names フロントスタビライザーバー(2.6mm / 1pcs / MP9) Front Sway Bar (2.6mm/1pcs/MP9) フロントスタビライザーバー(2.8mm / 1pcs / MP9) Front Sway Bar (2.8mm/1pcs/MP9) リヤスタビライザーバー(2.3mm / 1pcs / MP9) Rear Sway Bar (2.3mm/1pcs/MP9) リヤスタビライザーバー(2.5mm / 1pcs / MP9) Rear Sway Bar (2.5mm/1pcs/MP9) リヤスタビライザーバー(2.6mm / 1pcs / MP9) Rear Sway Bar (2.6mm/1pcs/MP9) リヤスタビライザーバー(3.0mm / 1pcs / MP9) Rear Sway Bar (3.0mm/1pcs/MP9) ホイール(4pcs / 蛍光イエロー / MP9) Wheel (4pcs / Fluorescent Yellow / MP9) ホイール(4pcs / ホワイト / MP9) Wheel (4pcs / White / MP9) SP クラッチベル (14T) IFW47 SP Clutch Bell (14T) 3PC クラッチシュー IFW52 3PC Clutch Shoe IFW53 H IFW53 M IFW53 S IFW107 BL IFW107 G IFW117 -01 1680 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 T-Shirt With AKA Logo 品番 No. IF459 -2.6 IF459 -2.8 IF460 -2.3 IF460 -2.5 IF460 -2.6 IF460 -3.0 IFH003 KY IFH003 W 3360 アクセサリー 品番 No. AKA98101 L AKA98101 M AKA98101 S AKA98101 XL AKA98101 XXL OPTIONAL PARTS AKA98201 39778 パーツ名 Part Names AKA ベースボールキャップ(BK) AKA Baseball Cap (Black) AKA スポンサーデカール(L) AKA Sponsor Decal Sheet (Large) Team KYOSHO ステッカー Team KYOSHO Sticker KYOSHO ワークスステッカー KYOSHO Works Sticker ★ FOR JAPANESE MARKET ONLY. 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 210 一律 840 (税込) 3990 オリジナルステッカー Original Sticker オリジナルステッカー 3 枚入 Original Sticker 3pcs 840 オリジナルステッカー 2 枚入 525 Original Sticker 2pcs ツール 品番 No. パーツ名 Part Names クイックフューエルガン(口径 12mm) 36201 Quick Fuel Gun (Caliber 12mm) 3PC クラッチシューツール 36206 3PC Clutch Shoe Tool SP ナイフエッジリーマー 36219 SP Knife Edge Reamer 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 曖時に燃料をタンクに注入 Instantly fills fuel tank クラッチシューの脱着に便利なツール Tool for removing clutch shoe ボディーの穴開けに便利 Tool for making holes on Bodies. 210 一律 525 (税込) 4725 1890 ボックス・バック 品番 No. 80460 80461 80462 80463 パーツ名 Part Names ピットボックス(DX) Pit Box (DX) ピットボックス Pit Box ツールボックス Tool Box パーツボックス(L) Parts Box (L) 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 工具収納に最適 542x300x397mm 工具収納に最適 420x240x330mm サイズ / 330x230x65mm Size / 330x230x65mm サイズ / 410x264x43mm Size / 410x264x43mm 品番 No. パーツ名 Part Names ORION スポーツパワー 2200 ORI10325 ORION Sports Power 2200 2200mAh Ni-MH Battery ORION1600 レシーバーパック ORI12227 (俵型 : ユニプラグ) ORION1600 Raceiver Pack Battery (Hump Type : Uniplug) 受信機用電源 ORION1600 レシーバーパック 受信機用電源 ★ ORI12232 (俵型 :BEC プラグ) ORION1600 Raceiver Pack Battery (Hump Type : BEC plug) サーモメーター mini 36207 Thermo Meter mini For receiver BOX • BAG 品番 No. 1890 80466 1890 87822 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 2200mAh ニッケル水素バッテリー パーツ名 Part Names フライホイールプーラー 80162 Flywheel Puller クロスレンチ(5.5/7.0/8.0/10mm) 80164 Cross Wrench (5.5/7.0/8.0/10mm) フュールポンプ 500cc 96423 Fuel Bottle 500cc 80464 エレクトリック 210 一律 2520 (税込) 2625 ★ FOR JAPANESE MARKET ONLY. 品番 No. 210 一律 7140 (税込) Good for storing tools 542x300x397mm 16800 Good for storing tools 420x240x330mm TOOL 80465 フライホイール取外し工具 Detaching tool for flywheel. 2625 スピーディーな給油が可能 1050 For quick refueling. 210 一律 473 (税込) ★ FOR JAPANESE MARKET ONLY. パーツ名 Part Names パーツボックス (M) Parts Box (M) パーツボックス (S) Parts Box (S) パーツボックス (SS) Parts Box (SS) Team KYOSHO プロポバッグ Team KYOSHO Transmitter Bag ELECTRIC 品番 No. 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 サイズ / 232x122x32mm Size / 232x122x32mm サイズ / 120x83x25mm Size / 120x83x25mm サイズ / 89x36x26mm Size / 89x36x26mm 送信機用バッグ For Transmitter 210 一律 158 (税込) 578 420 2940 ★ FOR JAPANESE MARKET ONLY. パーツ名 Part Names 内容(キー No. と入数) ★定価 ★発送 Quantity (税込)手数料 スパークブースター 2.0(オリオン 2200 バッテリー付) バッテリーコンディションメーター付プラグヒーター 36216S Spark Booster 2.0 (with ORION 2200 Battery) Spark booster with battery condition meter ブースターチャージャー 2.0 デジタルピークオートカット付プラグヒートチャージャー 36217 Booster Charger 2.0 Plug heater delta peak auto-cut charger 210 一律 1995 (税込) 2730 スパークブースター用充電器 Charger for plug heater 別途 12V 電源が必要 2520 For receiver 非接触型デジタル温度計 一式 Noncontact digital thermometer 1 set Requires 12V power source 2940 エンジンヘッドの温度測定に便利 Measures engine head temp. マルチスターターボックス 2.0 1/10〜1/8 モデル用 36209 Multi Starter Box 2.0 For 1/10~1/8 models Power Zone ★ 72301 AC/DC クイックチャージャー Power Zone AC/DC Quick Charger 1〜12 セル対応チャージャー Power Zone PS-25A(DC12V 安定化電源) ★ 72321 Power Zone PS-25A AC100V 電源 -DC12V 安定化電源 Suitable for 1-12 cells. 18690 スパークブースターの充電も可能 Able to charge plug heater AC100V-DC12V Electronic equipment. 14700 8190 エンジン始動用スターターボックス For starting the engine. 別途 7.2V バッテリー 2 本必要 Requires two 7.2V batteries Glow Engine Fuel 模型用燃料 パーツ名 内容(キー No. と入数) Part Names Quantity スーパーカナイフュエル(30%) 30% ニトロ • 2 リットル ★ 73121 SUPER KANAI FUEL (30%) 30% nitromethane, 2 liter 品番 No. ★定価 (税込) 3990 GLOW FUEL ★ FOR JAPANESE MARKET ONLY. KYOSHO OIL 800 品番 No. 1879 ★ 36901 96152 96154 ★ 96155 96159 96160 96162 96172 品番 No. KYOSHO OIL 1000 ケミカル・オイル CHEMICAL • OIL パーツ名 内容(キー No. と入数) ★定価 ★発送 Part Names Quantity (税込)手数料 2g/2 本入 ホビーグリス 158 210 Hobby Grease 2g/2pcs 一律 スーパーパワークリーナー マシンの汚れ落とし 893 (税込) Super Power Cleaner Cleaner spray of car. シリコンシール デフオイルのもれ防止 840 Silicone Seal Prevents diff oil from leaking KYOSHO スペシャルグルー(14g) 瞬間接着剤 735 KYOSHO Special Glue (14g) Instant Glue KYOSHO スペシャルプライマー(220ml) 瞬間接着剤の硬化促進剤 2100 KYOSHO Special Primer (220ml) Stiffering accelerant of instant gule. ダストガードプライマー マフラーの汚れの焼きつき、こびりつき防止 1890 Prevents dirt from sticking on mufflers Dust Guard Primer FRP ジェルシート(1.0) ボディー補修や強化等に 2100 FRP Gel Sheet (1.0) For body repair and reinforcement リングギヤグリス(3g) テフロン特殊グリス 420 Ring Gear Grease (3g) Teflon special grease. シリコンオイルケース(16 本) シリコンオイル用ケース ★ 735 Silicone Oil Case (16pcs) Case for silicone oil パーツ名 Part Names シリコンオイル(100) SIL0100 Silicone Oil (100) シリコンオイル(150) SIL0150 Silicone Oil (150) シリコンオイル(200) SIL0200 Silicone Oil (200) シリコンオイル(250) SIL0250 Silicone Oil (250) シリコンオイル(300) SIL0300 Silicone Oil (300) シリコンオイル(350) SIL0350 Silicone Oil (350) シリコンオイル(400) SIL0400 Silicone Oil (400) シリコンオイル(450) SIL0450 Silicone Oil (450) シリコンオイル(500) SIL0500 Silicone Oil (500) シリコンオイル(550) SIL0550 Silicone Oil (550) シリコンオイル(600) SIL0600 Silicone Oil (600) シリコンオイル(650) SIL0650 Silicone Oil (650) 内容(キー No. と入数)★定価 ★発送 Qty. (税込)手数料 品番 No. SIL0700 SIL0800 SIL0900 SIL1000 SIL1100 ダンパー用 各630 210 for shocks. 一律 (40cc) (税込) SIL1200 SIL1300 SIL2000 SIL3000 SIL4000 SIL5000 SIL6000 パーツ名 Part Names シリコンオイル(700) Silicone Oil (700) シリコンオイル(800) Silicone Oil (800) シリコンオイル(900) Silicone Oil (900) シリコンオイル(1000) Silicone Oil (1000) シリコンオイル(1100) Silicone Oil (1100) シリコンオイル(1200) Silicone Oil (1200) シリコンオイル(1300) Silicone Oil (1300) シリコンオイル(2000) Silicone Oil (2000) シリコンオイル(3000) Silicone Oil (3000) シリコンオイル(4000) Silicone Oil (4000) シリコンオイル(5000) Silicone Oil (5000) シリコンオイル(6000) Silicone Oil (6000) 品番 No. 96174 96175 96178 96180 96181 ★ FOR JAPANESE MARKET ONLY. パーツ名 内容(キー No. と入数) ★定価 ★発送 Part Names Quantity (税込)手数料 ノイズキャンセルシート 受信機ノイズ防止シート 840 210 To suppress receiver noise. Noise Cancel Sheet 一律 放熱グリス (10g) 熱伝導促進グリス 945 (税込) Grease improves conduction of heat. Thermal Grease (10g) ロックタイト(中強度 10cc) ビスの緩み防止剤 1260 Loctite (medium strength 10cc) Stops loosing screw マイクロロン プレシジョンオイラー ベアリング潤滑剤(7.4cc) 3150 Microlon Precision Oiler Great fuel bearings (7.4cc) マイクロロン トップエンド 燃料添加剤(30cc) 5145 Microlon Top End Glow fuel additive (30cc) マイクロロン アッセンブリールブリカント 96182 Microlon Assembly Lubricant HG ジョイントグリス 96508 HG Joint Grease SP ベアリングリキッド 96625 Special Bearing Liquid トルネード アフターランオイル 607011 Tornado After Run Oil 内容(キー No. と入数)★定価 ★発送 Qty. (税込)手数料 ダンパー用 for shocks. (40cc) デフ用 for diffs. (40cc) 各630 210 一律 (税込) 品番 No. 組立用潤滑剤(20g) For metal parts (20g) 3570 ジョイント部用グリス 840 Grease for joint part. ベアリング本来の性能を発揮 1050 使用後のエンジンメンテナンス用 630 Retrieves potentiality of Bearing. For Engine maintenance. パーツ名 Part Names シリコンオイル(7000) SIL7000 Silicone Oil (7000) シリコンオイル(10000) SIL10000 Silicone Oil (10000) シリコンオイル(20000) SIL20000 Silicone Oil (20000) シリコンオイル(30000) SIL30000 Silicone Oil (30000) シリコンオイル(40000) SIL40000 Silicone Oil (40000) シリコンオイル(50000) SIL50000 Silicone Oil (50000) シリコンオイル(60000) SIL60000 Silicone Oil (60000) シリコンオイル(80000) SIL80000 Silicone Oil (80000) シリコンオイル(100000) SIL100000 Silicone Oil (100000) シリコンオイル(300000) SIL300000 Silicone Oil (300000) シリコンオイル(500000) SIL500000 Silicone Oil (500000) 内容(キー No. と入数)★定価 ★発送 Qty. (税込)手数料 デフ用 for diffs. (40cc) 各630 210 一律 (税込) 各1365 ビス・ナット類 SCREW • NUT etc. 品番 No. 1101 1102 1103 1104 1105 1106 1107 1108 サイズ(mm) Size (mm) ナベビス Round Head Screw 2x6 • 2x8 • 2x10 • 2x15 2.6x8 • 2.6x10 • 2.6x12 • 2.6x14 3x4 • 3x6 • 3x8 • 3x10 • 3 x12 3x14 • 3x16 • 3x18 • 3x20 4x6 • 4x8 • 4x10 • 4x12 3x22 • 3x24 • 3x26 • 3x28 2.6x25 2.6x30 1110 1111 1112 1113 1114 1115 バインドビス Bind Screw 2.6x4 • 2.6x6 • 2.6x8 • 2.6x12 3x4 • 3x6 • 3x8 • 3x10 • 3x12 3x14 • 3x16 • 3x18 • 3x20 4x6 • 4x8 • 4x10 • 4x12 3x22 • 3x25 • 3x28 • 3x30 4x15 • 4x18 • 4x20 • 4x22 サラビス Flat Head Screw 入数(各) QUANTITY ★210 (税込) 5 each 5 each 5 each 5 each 5 each 5 each 10 pcs 8 pcs ★210 (税込) 5 each 5 each 5 each 5 each 5 each 5 each ★210 2.6x6 2.6x8 • 2.6x10 • 2.6x12 • 2.6x14 3x6 • 3x8 • 3x10 • 3x12 3x14 • 3x16 • 3x18 • 3x20 4x8 • 4x10 • 4x15 • 4x20 3x22 • 3x24 • 3x26 • 3x28 3x30 • 3x32 • 3x34 • 3x35 4x12 4x6 10 pcs 5 each 5 each 5 each 5 each 5 each 5 each 10 pcs 10 pcs ★210 1124 1125 1126 1127 1128 1129 1130 1131 1196 キャップビス Cap Screw 2x8 • 2x10 • 2x12 • 2x14 2.6x8 • 2.6x10 • 2.6x12 • 2.6x14 3x8 • 3x10 • 3x12 • 3x14 3x15 • 3x16 • 3x18 • 3x20 3x25 • 3x30 • 3x35 • 3x40 4x10 • 4x15 • 4x20 4x25 • 4x28 • 4x30 4x35 • 4x40 • 4x45 2.6x18 1391 3x22 1132 1133 1134 1135 1136 1137 1140 1141 1142 1143 2x4 • 2x6 • 2x8 • 2x10 2.6x6 • 2.6x8 • 2.6x10 • 2.6x12 3x6 • 3x8 • 3x10 • 3x12 • 3x14 3x15 • 3x16 • 3x18 • 3x20 3x25 • 3x30 • 3x35 2.6x14 • 2.6x15 • 2.6x16 • 2.6x18 バインドタッピングビス Bind Self-Tapping Screw 2.6x6 • 2.6x8 • 2.6x10 • 2.6x12 3x6 • 3x8 • 3x10 • 3x12 • 3x14 3x15 • 3x16 • 3x18 • 3x20 4x10 • 4x15 • 4x18 サラタッピングビス Flat Head Self-Tapping Screw 1147 1148 1149 1150 1151 2.6x6 • 2.6x8 • 2.6x10 • 2.6x12 3x6 • 3x8 • 3x10 • 3x12 • 3x14 3x15 • 3x16 • 3x18 • 3x20 4x15 • 4x20 • 4x25 4x8 • 4x12 ボタンヘックスビス Button Hex Screw 1366 1367 1368 1370 1388 1389 1395 3x6 3x8 3x10 3x12 3x15 3x18 3x25 ボタンヘックスビス Button Hex Screw 1369 2.6x5 ボタンヘックスビス Button Hex Screw 1401 1402 1403 1406 4x8 4x18 4x22 2x5 2 each 2 each 2 each 2 each 2 each 2 each 2 each 2 each 4 pcs ★315 (税込) 3x6 • 3x8 • 3x10 4x8 • 4x10 • 4x12 1160 1161 1162 1163 1164 1165 1166 1167 1301 1302 1303 1304 チタンバインドビス Titanium Bind Screw 1311 1312 1313 1314 3x8 3x10 3x15 3x18 1321 1322 1323 1324 3x8 3x10 3x12 3x15 1325 1326 1327 4x15 4x20 4x25 1331 1332 1333 1334 (税込) 3x8 3x10 3x12 3x15 5 each 5 each 5 each 5 each 5 each 5 each ★210 (税込) 5 each 5 each 5 each 5 each ★210 (税込) 5 each 5 each 5 each 5 each 5 each ★315 4x6 4x10 4x15 4x20 3x8 3x10 3x12 3x15 3x6 3x8 3x10 3x12 3x15 3x6 10 pcs 10 pcs 10 pcs 10 pcs 10 pcs 10 pcs 5 pcs ★420 (税込) 10 pcs ★315 (税込) ★210 (税込) 2 each 2 each 1376 1377 1378 1379 1392 1393 4x10 4x12 4x15 4x18 4x6 4x25 (税込) 2mm • 2.6mm 3mm • 4mm フランジ付ナット Flanged Nut 1174 1175 ナイロンナット Nylon Nut 1177 1178 1179 1181 1183 2.6mm 3mm 4mm 5mm 3mm(薄) フランジ付ナイロンナット Flanged Nylon Nut 1180 4mm 4mm(ブルー) 4mm(レッド) フランジ付スチールカラーナイロンナット Flanged Steel Color Nylon Nut 1359 1360 4mm(ブルー) 4mm(レッド) アルミナイロンナット Aluminum Nylon Nut 1341 1342 1343 1344 1345 1346 1347 1349 1350 1351 1353 1354 1355 4mm(シルバー) 4mm(ブルー) 4mm(レッド) 4mm(ゴールド) 3mm(シルバー) 3mm(ブルー) 3mm(レッド) 3mm(シルバー) (薄) 3mm(ブルー) (薄) 3mm(レッド) (薄) 4mm(シルバー) 4mm(ブルー) 4mm(レッド) ワッシャー Washer (税込) 1185 1186 1189 1190 2mm • 2.6mm • 3mm 4mm • 5mm 2.6 x 7 x 0.5 7x 11 x 0.5 • 7 x 11 x 1 ★525 ワッシャー Washer (税込) ★525 (税込) ★315 1188 96651 3 x 10 x 1 12 x 15 x 0.5 Eリング E-Clips 1380 1381 1382 1383 1384 1385 1386 1387 1390 E1.5 E2.0 E2.5 E3.0 E4.0 E5.0 E6.0 E7.0 E10.0 ★210 (税込) 10 each 10 each ★210 (税込) ★210 (税込) 5 pcs 5 pcs 5 pcs 4 pcs 5 pcs ★210 (税込) 5 pcs フランジ付スチールカラーナット Flanged Steel Color Nut 1357 1358 入数(各) QUANTITY 10 pcs 10 pcs 3mm 4mm ★630 ★315 (税込) 8 pcs 8 pcs ★420 (税込) 8 pcs 8 pcs ★315 (税込) 4 pcs 4 pcs 4 pcs 4 pcs 5 pcs 5 pcs 5 pcs 5 pcs 5 pcs 5 pcs 5 pcs 5 pcs 5 pcs ★210 (税込) 10 each 10 each 10 pcs 3 each ★420 (税込) 10 pcs 10 pcs ★158 (税込) 10 pcs 10 pcs 10 pcs 10 pcs 10 pcs 10 pcs 10 pcs 6 pcs 6 pcs (税込) 10 pcs 10 pcs 10 pcs 10 pcs 10 pcs 10 pcs 3x6 3x8 3x10 3x5 3x15 3x18 サラヘックスビス Flat Head Hex Screw 1396 1397 1398 1399 1411 1412 ★420 8 pcs 8 pcs 8 pcs 8 pcs 8 pcs サラヘックスビス Flat Head Hex Screw (税込) (税込) 8 pcs 8 pcs 8 pcs 8 pcs 8 pcs チタンビスサラヘックス Titanium Socket F/H Screw 1371 1372 1373 1374 1375 ★630 8 pcs 6 pcs 5 pcs 4 pcs チタンビスボタンヘックス Titanium Socket Screw 1361 1362 1363 1364 1365 (税込) 10 pcs 10 pcs 10 pcs 8 pcs チタンサラビス Titanium Flat Head Screw 1335 1336 1337 1338 ★420 4 pcs 4 pcs 4 pcs チタンサラビス Titanium Flat Head Screw 1171 1172 径 mm ナット Nut (税込) 10 pcs 10 pcs 10 pcs 8 pcs チタンサラタッピングビス Titanium Flat Head Self-Tapping Screw 品番 No. ★420 10 pcs 10 pcs 10 pcs 8 pcs チタンサラタッピングビス Titanium Flat Head Self-Tapping Screw ★210 10 pcs 5 pcs 5 pcs 10 pcs フランジ付キャップビス Flanged Cap Screw 1153 1154 (税込) 5 pcs ナベタッピングビス Round Head Self-Tapping Screw 1157 サイズ(mm) 入数(各) Size (mm) QUANTITY ★210 サラ小丸ビス (税込) Oval Head Screw 10 each 2x8 • 2x10 セットビス ★210 Set Screw (税込) 3 each 3x6 • 3x12 • 3x14 • 3x16 3 each 3x3 • 3x4 • 3x5 • 3x10 3 each 4x4 • 4x5 • 4x8 • 4x12 3 each 5x4 • 5x5 • 5x6 3 each 5x30 • 5x40 3x20 • 3x25 3 each 4x8 10 pcs 4x20 2 pcs チタンバインドタッピングビス ★420 (税込) Titanium Bind Self-Tapping Screw 3x8 10 pcs 3x10 10 pcs 3x12 10 pcs 3x15 8 pcs (税込) 1117 1118 1119 1120 1121 1122 1123 1168 1197 キャップビス Cap Screw 品番 No. FOR JAPANESE MARKET ONLY. ★ ★420 (税込) 10 pcs 10 pcs 10 pcs 6 pcs 10 pcs 5 pcs ここに明記された以外のビス、ナット等は 『ユーザー相談室』にお問い合わせください。