Download CC EMP4

HP-19014-4
OPERATING MANUAL
Cable for connection between
driver and controller (Conforms to EMP series)
CC
EMP4
Connector pin assignments
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures.
● Please read it thoroughly to ensure safe operation.
● Always keep the manual where it is readily available.
Controller side
Pin no.
Driver side
Pin no.
Sensor side
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
11
12
9
10
29
23
25
33
34
21
22
24,26,30
19
20
17
18
1
2
+LS
-LS
HOME
SLIT
DC OUT
GND
-
Only qualified personnel should work with the product.
The product described in this manual has been designed and manufactured for use in general industrial machinery, and must not be
used for any other purpose. Oriental Motor Co., Ltd. is not responsible for any damage caused through failure to observe this warning.
This Operating Manual is subject to change without prior notice for
the purpose of product improvement or changes in specifications, or
to improve its general content.
While we make every effort to offer accurate information in the manual, we welcome your input.
Should you find unclear descriptions, errors or omissions, please
contact the nearest office.
,
,
and
are trademarks of Oriental
Motor Co., Ltd., and are registered in Japan and other countries.
is a trademark of Oriental Motor Co., Ltd.
© Copyright ORIENTAL MOTOR CO., LTD. 2006
■ Hazardous substances
RoHS (Directive 2002/95/EC 27Jan.2003) compliant
Checking the product
This cable permits one-touch connection of the EMP series stored
programming controller with an
,
or FXE series driver.
Verify that the model number of the driver-sensor cable product
you’ve received is the correct one.
Model
Lenght
CC01EMP4
1m (3.3ft.)
CC02EMP4
2m (6.6ft.)
Applicable driver mode
Note
DC OUT is used to output the controller’s 12/24 V, so do not input any
external power supply to DC OUT. Doing so may damage the internal
circuit of the controller.
● Do not rework or modify the cable. Doing so may result in damage or
malfunction of the controller, driver, and sensor.
● To dispose of the cable, disassemble it into parts and components as
much as possible and dispose of individual parts/components as
industrial waste.
●
FXE series
Functions of parts
Sensor side
Connect to a limit sensor, home
sensor, etc. For details, refer to the
operating manual
for your EMP controller.
UT
DC O
GND
+LS
-LS
HOME
SLIT
● Please
contact your nearest ORIENTAL MOTOR office for further information.
ORIENTAL MOTOR U.S.A. CORP.
Technical Support Line Tel:(800)468-3982
Available from 7: 30 AM to 5:00 PM, P.S.T.
E-mail : [email protected]
www.orientalmotor.com
ORIENTAL MOTOR (EUROPA) GmbH TAIWAN ORIENTAL MOTOR CO., LTD.
Controller side
Connect to the AXIS1 or AXIS2
connector on your EMP controller.
Driver side
Connect to the control I/O connector on
your
,
or FXE driver.
Headquarters and Düsseldorf Office
Tel:0211-5206700
Fax:0211-52067099
Munich Office
Tel:08131-59880
Fax:08131-598888
Hamburg Office
Tel:040-76910443
Fax:040-76910445
ORIENTAL MOTOR (UK) LTD.
Tel:01256-347090
Fax:01256-347099
ORIENTAL MOTOR (FRANCE) SARL
Tel:01 47 86 97 50
Fax:01 47 82 45 16
ORIENTAL MOTOR ITALIA s.r.l.
Tel:02-93906346
Fax:02-93906348
Tel:(02)8228-0707
Fax:(02)8228-0708
SINGAPORE ORIENTAL MOTOR PTE. LTD.
Tel:(6745)7344
Fax:(6745)9405
ORIENTAL MOTOR (MALAYSIA) SDN. BHD.
Tel:(03)79545778
Fax:(03)79541528
INA ORIENTAL MOTOR CO., LTD.
KOREA
Tel:(032)822-2042~3 Fax:(032)819-8745
ORIENTAL MOTOR CO., LTD.
Headquarters Tokyo, Japan
Tel:(03)3835-0684
Fax:(03)3835-1890
Printed on Recycled Paper