Download Cyclope-Orion - user manual - COMPLETE

ENGLISH
OPERATION MANUAL
ENGLISH
OPERATION MANUAL
Show Mode
Used to choose to select one of the preprogrammed shows when used in standalone or master/slave
mode. This menu option is not available when the unit is set to slave mode (“S L 1 ” or “S L 2 ”)!
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the current show starts blinking in the display.
Use DOWN and UP buttons to select one of the preprogrammed shows
(show 0) to
12) or S hL O (slow mode)
 Once the right show blinks on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
(show
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to master mode.
This menu option is not available when the unit is set to slave mode (“S L 1 ” or “S L 2 ”)!
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the current selection starts blinking in the display.
 Use DOWN and UP button to select Y E S (blackout) or n o (no blackout) mode.
 Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
DMX512 Address Setting
Used to set the starting address in a DMX setup.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to change the DMX512 address.
 Once the correct address shows on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Led Display
Display on: display is always on.
Display off: display is off when not used.




Press the MENU button until the display shows
.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
(display always on) or
(display off when not used).
Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Channel Mode
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select the 4ch (4 Channel ) or 7ch (7 Channel) mode.
Once the mode is selected, press the ENTER button to setup
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.




Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button until
is blinking on the display. (normal display)
 Use the ENTER button to change to the mode
(display inversion), the option will be automatically
stored after 8 seconds. Or press the ENTER button again return to the mode
(normal display).
To go back to the functions press the MENU button.
Working Mode
Used to set the unit in master or slave mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the current working mode starts blinking in the display
 Use the DOWN and UP buttons to select
(master),
(slave in sync with the master) or
(2 light show – slave in anti-sync with the master).
 Once the mode is selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Remarks: when “SL 1” or “SL 2” is selected, some menu options are not available. When only one unit is
used, you should always select master mode.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button until
is blinking on the display.
 Press the ENTER button to show the number of working hours in the display.
 To go back to the functions press the MENU button.
Software version:
Used to show the software version of the unit.
 Press the MENU button until
blinks on the display.
 Press the ENTER button to show the software version of the unit.
 To go back to the functions press the MENU button.
JB SYSTEMS®
5/50
ORION
JB SYSTEMS®
6/50
ORION