Download Oxi - Meßumformer Oxi 170 Oxi 296 Oxi 170 Oxi 296
Transcript
Bedienungsanleitung Bedienungsanleitung Oxi - Meßumformer ba24105de Oxi - Meßumformer Oxi 170 Oxi 296 ba24105de06 Oxi 170 Oxi 296 Oxi 170 Oxi 170 Oxi 296 Oxi 296 Bedienungsanleitung Seite 1 Bedienungsanleitung Seite 1 Operating manual Page 67 Operating manual Page 67 11/2004 ba24105de04 07/01 Allgemeine Informationen Allgemeine Informationen Aktualität bei Drucklegung Fortschrittliche Technik und das hohe Qualitätsniveau unserer Geräte werden durch eine ständige Weiterentwicklung gewährleistet. Daraus können sich evtl. Abweichungen zwischen dieser Bedienungsanleitung und Ihrem Gerät ergeben. Auch Irrtümer können wir nicht ganz ausschließen. Haben Sie deshalb bitte Verständnis, daß aus den Angaben, Abbildungen und Beschreibungen keine juristischen Ansprüche abgeleitet werden können. Aktualität bei Drucklegung Fortschrittliche Technik und das hohe Qualitätsniveau unserer Geräte werden durch eine ständige Weiterentwicklung gewährleistet. Daraus können sich evtl. Abweichungen zwischen dieser Bedienungsanleitung und Ihrem Gerät ergeben. Auch Irrtümer können wir nicht ganz ausschließen. Haben Sie deshalb bitte Verständnis, daß aus den Angaben, Abbildungen und Beschreibungen keine juristischen Ansprüche abgeleitet werden können. Garantieerklärung Garantieerklärung Wir übernehmen für das bezeichnete Gerät eine Garantie von zwei Jahren ab Kaufdatum. Die Gerätegarantie erstreckt sich auf Fabrikationsfehler, die sich innerhalb der Garantiefrist herausstellen. Wir übernehmen für das bezeichnete Gerät eine Garantie von zwei Jahren ab Kaufdatum. Die Gerätegarantie erstreckt sich auf Fabrikationsfehler, die sich innerhalb der Garantiefrist herausstellen. Der Garantieanspruch erstreckt sich auf die Wiederherstellung der Funktionsbereitschaft, nicht jedoch auf die Geltendmachung weitergehender Schadensersatzansprüche. Bei unsachgemäßer Behandlung oder bei unzulässiger Öffnung des Geräts erlischt der Garantieanspruch. Der Garantieanspruch erstreckt sich auf die Wiederherstellung der Funktionsbereitschaft, nicht jedoch auf die Geltendmachung weitergehender Schadensersatzansprüche. Bei unsachgemäßer Behandlung oder bei unzulässiger Öffnung des Geräts erlischt der Garantieanspruch. Zur Feststellung der Garantiepflicht das Gerät und den Kaufbeleg mit Kaufdatum frachtfei bzw. postfrei einsenden. Zur Feststellung der Garantiepflicht das Gerät und den Kaufbeleg mit Kaufdatum frachtfei bzw. postfrei einsenden. Copyright Copyright Weilheim 1999, WTW GmbH & Co. KG Nachdruck – auch auszugsweise – nur mit schriftlicher Genehmigung der WTW GmbH & Co. KG, Weilheim. Printed in Germany. Weilheim 1999, WTW GmbH & Co. KG Nachdruck – auch auszugsweise – nur mit schriftlicher Genehmigung der WTW GmbH & Co. KG, Weilheim. Printed in Germany. 2 2 Sicherheitshinweise Oxi 170/ Oxi 296 Sicherheitshinweise Bitte lesen Sie diese Sicherheitshinweise vor Inbetriebnahme des Gerätes aufmerksam durch! Oxi 170/ Oxi 296 Bitte lesen Sie diese Sicherheitshinweise vor Inbetriebnahme des Gerätes aufmerksam durch! Dieses Gerät ist gemäß den gesetzlich geforderten Sicherheitsbestimmungen für elektronische Meßgeräte gebaut und hat das Werk in sicherheitstechnisch einwandfreiem Zustand verlassen (IEC 1010). Dieses Gerät ist gemäß den gesetzlich geforderten Sicherheitsbestimmungen für elektronische Meßgeräte gebaut und hat das Werk in sicherheitstechnisch einwandfreiem Zustand verlassen (IEC 1010). Die einwandfreie Funktion und Betriebssicherheit des Gerätes ist nur dann gewährleistet, wenn bei der Benutzung die allgemein üblichen Sicherheitsvorkehrungen sowie die speziellen Sicherheitshinweise in dieser Bedienungsanleitung beachtet werden. Die einwandfreie Funktion und Betriebssicherheit des Gerätes ist nur dann gewährleistet, wenn bei der Benutzung die allgemein üblichen Sicherheitsvorkehrungen sowie die speziellen Sicherheitshinweise in dieser Bedienungsanleitung beachtet werden. – Vor dem Einschalten des Gerätes sicherstellen, daß die am Gerät angegebene Betriebsspannung mit der Versorgungsspannung übereinstimmt (Angabe der Bereiche der Spannungsversorgung). – Vor dem Einschalten des Gerätes sicherstellen, daß die am Gerät angegebene Betriebsspannung mit der Versorgungsspannung übereinstimmt (Angabe der Bereiche der Spannungsversorgung). – Der Betrieb des Gerätes ist nur zulässig mit Zubehör, das den Spezifikationen im Kapitel "Technische Daten" in dieser Bedienungsanleitung entspricht. Für Schäden, die durch Verwendung nicht geeigneten Zubehörs entstehen können, übernimmt der Hersteller keine Haftung. – Der Betrieb des Gerätes ist nur zulässig mit Zubehör, das den Spezifikationen im Kapitel "Technische Daten" in dieser Bedienungsanleitung entspricht. Für Schäden, die durch Verwendung nicht geeigneten Zubehörs entstehen können, übernimmt der Hersteller keine Haftung. – Die einwandfreie Funktion und Betriebssicherheit des Gerätes kann nur unter den klimatischen Verhältnissen, die im Kapitel “Technische Daten” in dieser Bedienungsanleitung spezifiziert sind, eingehalten werden. – Die einwandfreie Funktion und Betriebssicherheit des Gerätes kann nur unter den klimatischen Verhältnissen, die im Kapitel “Technische Daten” in dieser Bedienungsanleitung spezifiziert sind, eingehalten werden. – Das Öffnen des Gerätes sowie Abgleich-, Wartungs- und Reparaturarbeiten dürfen nur durch eine von WTW autorisierte Fachkraft ausgeführt werden. Zuwiderhandlungen können je nach Sachlage den Verlust der Garantieansprüche zur Folge haben. – Das Öffnen des Gerätes sowie Abgleich-, Wartungs- und Reparaturarbeiten dürfen nur durch eine von WTW autorisierte Fachkraft ausgeführt werden. Zuwiderhandlungen können je nach Sachlage den Verlust der Garantieansprüche zur Folge haben. – Wenn anzunehmen ist, daß das Gerät nicht mehr gefahrlos betrieben werden kann, so ist es außer Betrieb zu setzen und vor einer weiteren Inbetriebnahme durch Kennzeichnung zu sichern. – Wenn anzunehmen ist, daß das Gerät nicht mehr gefahrlos betrieben werden kann, so ist es außer Betrieb zu setzen und vor einer weiteren Inbetriebnahme durch Kennzeichnung zu sichern. – Die Sicherheit des Benutzers kann durch das Gerät beeinträchtigt sein, wenn es zum Beispiel ! starke mechanische Beschädigungen aufweist, ! nicht mehr wie vorgeschrieben arbeitet, ! längere Zeit unter ungeeigneten Bedingungen gelagert wurde, ! erschwerten Transportbedingungen ausgesetzt war. – Die Sicherheit des Benutzers kann durch das Gerät beeinträchtigt sein, wenn es zum Beispiel ! starke mechanische Beschädigungen aufweist, ! nicht mehr wie vorgeschrieben arbeitet, ! längere Zeit unter ungeeigneten Bedingungen gelagert wurde, ! erschwerten Transportbedingungen ausgesetzt war. – In Zweifelsfällen sollte das Gerät grundsätzlich an den Hersteller "Wissenschaftlich-Technische-Werkstätten GmbH" zur Reparatur bzw. Wartung eingeschickt werden. – In Zweifelsfällen sollte das Gerät grundsätzlich an den Hersteller "Wissenschaftlich-Technische-Werkstätten GmbH" zur Reparatur bzw. Wartung eingeschickt werden. 3 3 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Inhaltsverzeichnis Inhaltsverzeichnis Sicherheitshinweise ..................................................................................................3 Sicherheitshinweise ..................................................................................................3 Inhaltsverzeichnis .....................................................................................................4 Inhaltsverzeichnis .....................................................................................................4 Beschreibung.............................................................................................................6 Frontansichten .......................................................................................................6 Bedienfeld..............................................................................................................7 Display .............................................................................................................7 Displaymeldungen............................................................................................8 Tastatur ..........................................................................................................10 Bedienhinweise ..............................................................................................10 Bedienebenen......................................................................................................11 Beschreibung.............................................................................................................6 Frontansichten .......................................................................................................6 Bedienfeld..............................................................................................................7 Display .............................................................................................................7 Displaymeldungen............................................................................................8 Tastatur ..........................................................................................................10 Bedienhinweise ..............................................................................................10 Bedienebenen......................................................................................................11 Installation ...............................................................................................................13 Allgemeine Hinweise ...........................................................................................13 Netzanschluß.......................................................................................................13 ”SENS-CHECK”-Anschluß...................................................................................14 REC 1 / REC 2 Anschlüsse .................................................................................14 K1 / K2 (Relaiskontakte) ......................................................................................14 Digitale Schnittstelle RS 485 (Option RS)............................................................15 Installationshinweise Oxi 170 ..............................................................................16 Klemmbelegung .............................................................................................16 Anschluß von Sensoren TriOxmatic® 690, TriOxmatic® 70x .........................17 Installationshinweise Oxi 296 ..............................................................................20 Klemmbelegung .............................................................................................20 TriOxmatic® 690, TriOxmatic® 70x anschließen ............................................21 Installation ...............................................................................................................13 Allgemeine Hinweise ...........................................................................................13 Netzanschluß.......................................................................................................13 ”SENS-CHECK”-Anschluß...................................................................................14 REC 1 / REC 2 Anschlüsse .................................................................................14 K1 / K2 (Relaiskontakte) ......................................................................................14 Digitale Schnittstelle RS 485 (Option RS)............................................................15 Installationshinweise Oxi 170 ..............................................................................16 Klemmbelegung .............................................................................................16 Anschluß von Sensoren TriOxmatic® 690, TriOxmatic® 70x .........................17 Installationshinweise Oxi 296 ..............................................................................20 Klemmbelegung .............................................................................................20 TriOxmatic® 690, TriOxmatic® 70x anschließen ............................................21 Konfiguration ...........................................................................................................24 Werkseinstellungen .............................................................................................24 Konfigurationsebene aufrufen..............................................................................25 Übersichtstabelle der Untermenüs.................................................................26 Salinitätskorrektur ................................................................................................27 Sensoren auswählen ...........................................................................................28 Auswahl Meßbereich ...........................................................................................29 Auswahl Schreiberausgang REC 1......................................................................30 Auswahl Schreiberausgang REC 2 (nur T-Option) ..............................................31 Relais 1 / Relais 2 (Option R) ..............................................................................32 Relaisfunktionen auswählen ..........................................................................32 Reglersignale.......................................................................................................33 Grenzwertmelder (UL.LL)...............................................................................33 Schaltrichtung (Öffner / Schließer) auswählen (FrC, UL.LL)..........................33 Konfiguration ...........................................................................................................24 Werkseinstellungen .............................................................................................24 Konfigurationsebene aufrufen..............................................................................25 Übersichtstabelle der Untermenüs.................................................................26 Salinitätskorrektur ................................................................................................27 Sensoren auswählen ...........................................................................................28 Auswahl Meßbereich ...........................................................................................29 Auswahl Schreiberausgang REC 1......................................................................30 Auswahl Schreiberausgang REC 2 (nur T-Option) ..............................................31 Relais 1 / Relais 2 (Option R) ..............................................................................32 Relaisfunktionen auswählen ..........................................................................32 Reglersignale.......................................................................................................33 Grenzwertmelder (UL.LL)...............................................................................33 Schaltrichtung (Öffner / Schließer) auswählen (FrC, UL.LL)..........................33 4 4 Inhaltsverzeichnis Oxi 170/ Oxi 296 Inhaltsverzeichnis Oxi 170/ Oxi 296 Parametrierung ........................................................................................................34 Werkseinstellungen .............................................................................................34 Parametrierebene aufrufen ..................................................................................35 Übersichtstabelle der Untermenüs .................................................................36 Parametrierung Salinität (nur wenn CSA 0n) ........................................................36 Schreiberausgang REC 1 und REC 2..................................................................37 Relais 1 / Relais 2 (Geräteausführung R) ................................................................38 Grenzwertmelder (UL.LL) ....................................................................................38 Parameter für Grenzwertmelder einstellen.....................................................39 Eingabe der manuellen Druckkompensation .......................................................41 Eingabe des Luftdrucks..................................................................................41 Eingabe der Ortshöhe ....................................................................................41 Schnittstelle RS 485 (Option RS) ...........................................................................42 Code einstellen ....................................................................................................42 Temperaturabgleich .............................................................................................43 Timer für externe Sensor-Reinigungseinheit (CS) ...............................................44 Zeitintervalle einstellen...................................................................................45 Parametrierung ........................................................................................................34 Werkseinstellungen .............................................................................................34 Parametrierebene aufrufen ..................................................................................35 Übersichtstabelle der Untermenüs .................................................................36 Parametrierung Salinität (nur wenn CSA 0n) ........................................................36 Schreiberausgang REC 1 und REC 2..................................................................37 Relais 1 / Relais 2 (Geräteausführung R) ................................................................38 Grenzwertmelder (UL.LL) ....................................................................................38 Parameter für Grenzwertmelder einstellen.....................................................39 Eingabe der manuellen Druckkompensation .......................................................41 Eingabe des Luftdrucks..................................................................................41 Eingabe der Ortshöhe ....................................................................................41 Schnittstelle RS 485 (Option RS) ...........................................................................42 Code einstellen ....................................................................................................42 Temperaturabgleich .............................................................................................43 Timer für externe Sensor-Reinigungseinheit (CS) ...............................................44 Zeitintervalle einstellen...................................................................................45 Betrachter-Modus ....................................................................................................46 Parametrier- und Konfigurationsdaten anzeigen............................................46 Kalibrierdaten und Softwareversion anzeigen................................................46 Betrachter-Modus ....................................................................................................46 Parametrier- und Konfigurationsdaten anzeigen............................................46 Kalibrierdaten und Softwareversion anzeigen................................................46 Meß-Modus...............................................................................................................47 Meß-Modus...............................................................................................................47 Kalibrierung .............................................................................................................48 Kalibrierfehler CAL Err ..........................................................................................49 Kalibrierung .............................................................................................................48 Kalibrierfehler CAL Err ..........................................................................................49 Prüfmodus................................................................................................................50 Prüfmodus aufrufen .............................................................................................50 Variantenerkennung.............................................................................................50 Codezahl anzeigen ..............................................................................................50 Schreiberausgang 1.............................................................................................51 Schreiberausgang 2.............................................................................................51 Relaistest .............................................................................................................52 RS 485 .................................................................................................................52 Ablaufplan ............................................................................................................53 Prüfmodus................................................................................................................50 Prüfmodus aufrufen .............................................................................................50 Variantenerkennung.............................................................................................50 Codezahl anzeigen ..............................................................................................50 Schreiberausgang 1.............................................................................................51 Schreiberausgang 2.............................................................................................51 Relaistest .............................................................................................................52 RS 485 .................................................................................................................52 Ablaufplan ............................................................................................................53 Reinigung / Wartung ...............................................................................................54 Reinigung / Wartung ...............................................................................................54 Störungsbehebung..................................................................................................55 Störungsbehebung..................................................................................................55 Technische Daten....................................................................................................56 Technische Daten Oxi 170 / Oxi 296 ...................................................................56 Technische Daten Oxi 296...................................................................................59 Technische Daten....................................................................................................56 Technische Daten Oxi 170 / Oxi 296 ...................................................................56 Technische Daten Oxi 296...................................................................................59 Anhang: Faltblätter Konfiguration und Parametrierung Anhang: Faltblätter Konfiguration und Parametrierung 5 5 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Beschreibung Frontansichten Frontansichten Oxi 170 Oxi 170 Oxi 170 Oxi 296 Oxi 170 Oxi 296 Oxi 296 6 Beschreibung Oxi 296 6 Oxi 170/ Oxi 296 Beschreibung Oxi 170/ Oxi 296 Beschreibung Bedienfeld Bedienfeld O2 ! ((8 Baud (((8 Ident O2 ! ((8 Baud (((8 Ident REL1 REL2 AR Display Display Meßmodus Sauerstoff Meßmodus Sauerstoff Steilheit Sensor Steilheit Sensor Alphanumerische Anzeige: Meßwert, Steilheit, Bedienerführung Alphanumerische Anzeige: Meßwert, Steilheit, Bedienerführung Dimension: % Dimension: % Dimension: mg/l Dimension: mg/l Alarmanzeige bei Sensordefekt Alarmanzeige bei Sensordefekt Eingabe Salinitätskorrektur Eingabe Salinitätskorrektur Dimension: °C Dimension: °C Relais 2 aktiv Relais 2 aktiv Kalibrierung: AutoRead ”aktiv” Kalibrierung: AutoRead ”aktiv” Relais 1 aktiv Relais 1 aktiv Automatische Kalibrierung REL1 REL2 AR OxiCal® Alphanumerische Anzeige: Automatische Kalibrierung OxiCal® Temperatur, Konfigurationsparameter Alphanumerische Anzeige: Temperatur, Konfigurationsparameter IDENT Nr. / RS 485-Betrieb IDENT Nr. / RS 485-Betrieb BAUD Rate / RS 485 Schnittstelle BAUD Rate / RS 485 Schnittstelle Salinitätskorrektur aktiv Salinitätskorrektur aktiv 7 7 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Beschreibung Displaymeldungen Beschreibung Displaymeldungen Hinweis: Der erste Buchstabe einer Displaymeldung dient der Zuordnung. Mit dem Anfangsbuchstaben "C" sind Konfigurationsanzeigen gekennzeichnet, ein "P" kennzeichnet Anzeigen der Parametrierung. Konfiguration: Hinweis: Der erste Buchstabe einer Displaymeldung dient der Zuordnung. Mit dem Anfangsbuchstaben "C" sind Konfigurationsanzeigen gekennzeichnet, ein "P" kennzeichnet Anzeigen der Parametrierung. Konfiguration: C0 Konfiguration COnfiguration C0 Konfiguration COnfiguration CSA Salinitätskorrektur Configuration SAlinity CSA Salinitätskorrektur Configuration SAlinity CIn Sensortyp Configuration Input CIn Sensortyp Configuration Input Crn Meßbereichsendwert Configuration range Crn Meßbereichsendwert Configuration range Cr1 Schreiberausgang 1 Configuration recorder 1 Cr1 Schreiberausgang 1 Configuration recorder 1 Cr2 Schreiberausgang 2 Configuration recorder 2 Cr2 Schreiberausgang 2 Configuration recorder 2 Relaisfunktion Configuration relais configuration Relaisfunktion Configuration relais configuration Relais Schließer/Öffner Configuration relais Function Relais Schließer/Öffner Configuration relais Function CrF Parametrierung: CrF Parametrierung: PA Parametrierung Parametrierung PA Parametrierung Parametrierung PSA Salinitätskorrektur Parametration SAlinity PSA Salinitätskorrektur Parametration SAlinity Pr1 Schreiberausgang 1 Parametration recorder 1 Pr1 Schreiberausgang 1 Parametration recorder 1 Pr2 Schreiberausgang 2 Parametration recorder 2 Pr2 Schreiberausgang 2 Parametration recorder 2 PL Grenzwertmelder Parametration Limits PL Grenzwertmelder Parametration Limits PPr Luftdruck Parametration Pressure PPr Luftdruck Parametration Pressure PAL Ortshöhe Parametration ALtitude PAL Ortshöhe Parametration ALtitude PIF Schnittstelle RS 485 Parametration InterFace PIF Schnittstelle RS 485 Parametration InterFace PCd Paßzahl Parametration Code PCd Paßzahl Parametration Code Pt Temperaturabgleich Parametration temperature Pt Temperaturabgleich Parametration temperature PCS Reinigungssystem Parametration Cleaning System PCS Reinigungssystem Parametration Cleaning System 8 8 Oxi 170/ Oxi 296 Beschreibung Allgemein: LL Allgemein: unterer Grenzwert Lower Limit oberer Grenzwert Upper Limit HS Hysterese HySteresis td Zeitverzögerung time delay LL Betrachter-Modus: Softwareversion Oxi 170/ Oxi 296 Beschreibung unterer Grenzwert Lower Limit oberer Grenzwert Upper Limit HS Hysterese HySteresis td Zeitverzögerung time delay Betrachter-Modus: Softwareversion Softwareversion 9 Softwareversion 9 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Beschreibung Tastatur • Tastatur Betriebstasten zum Umschalten zwischen Messen (M) und Kalibrieren (C) • Funktionstasten zum Wechseln der Betriebsebenen und Verändern von Einstellwerten bei Konfiguration und Parametrierung. • Betriebstasten zum Umschalten zwischen Messen (M) und Kalibrieren (C) • Funktionstasten zum Wechseln der Betriebsebenen und Verändern von Einstellwerten bei Konfiguration und Parametrierung. ESCAPE zum Verlassen eines Menüs UP Wert höher oder im Rollmodus nach oben ESCAPE zum Verlassen eines Menüs UP Wert höher oder im Rollmodus nach oben DOWN Wert kleiner oder im Rollmodus nach unten ENTER Eingaben bestätigen DOWN Wert kleiner oder im Rollmodus nach unten ENTER Eingaben bestätigen Bedienhinweise Bedienhinweise Die Bedienerführung ist teilweise über eine "Zwangsführung" realisiert, d.h. es müssen alle Menüs durchlaufen werden bei denen eine direkte Abhängigkeit besteht. Ein Code erlaubt den Zugang zu den Untermenüs PA (Parametrierung) und C0 (Konfiguration) (siehe Abschnitt "Konfiguration" und "Parametrierung"). Auswahl von C0 und PA durch die Tasten oder Wechsel zum nächsten Untermenü: Auswahl der gewünschten Einstellung: Die Bedienerführung ist teilweise über eine "Zwangsführung" realisiert, d.h. es müssen alle Menüs durchlaufen werden bei denen eine direkte Abhängigkeit besteht. Ein Code erlaubt den Zugang zu den Untermenüs PA (Parametrierung) und C0 (Konfiguration) (siehe Abschnitt "Konfiguration" und "Parametrierung"). Auswahl von C0 und PA durch die Tasten oder Wechsel zum nächsten Untermenü: oder Auswahl der gewünschten Einstellung: Übernahme der Einstellung: Übernahme der Einstellung: Rücksprung zum Programmbeginn: (außer bei Zwangsführung) Rücksprung zum Programmbeginn: (außer bei Zwangsführung) oder nach dem letzten Untermenü: oder nach dem letzten Untermenü: 10 Beschreibung 10 oder Beschreibung Oxi 170/ Oxi 296 Beschreibung Rückkehr zur Funktion "Messen/Kalibrieren" - solange keine Zwangsführung vorliegt: Oxi 170/ Oxi 296 Rückkehr zur Funktion "Messen/Kalibrieren" - solange keine Zwangsführung vorliegt: Bedienebenen Bedienebenen Die Gerätefunktionen sind in drei aufeinander aufbauenden Ebenen untergebracht, um eine klare und durchschaubare Strukturierung zu gewährleisten. Diese Struktur soll sicherstellen, daß dem Anwender ein Gerät mit universellen Möglichkeiten zur Verfügung steht, das aber so einstellbar ist, daß der sichere Meßbetrieb nicht durch unbeabsichtigte Eingriffe gestört wird. Die Gerätefunktionen sind in drei aufeinander aufbauenden Ebenen untergebracht, um eine klare und durchschaubare Strukturierung zu gewährleisten. Diese Struktur soll sicherstellen, daß dem Anwender ein Gerät mit universellen Möglichkeiten zur Verfügung steht, das aber so einstellbar ist, daß der sichere Meßbetrieb nicht durch unbeabsichtigte Eingriffe gestört wird. Betriebsebene: Konfiguration und Parametrierung können in der Betriebsebene ohne Codeeingabe abgefragt werden, während der Meßbetrieb weiterläuft. Die Einstellungen können jedoch nicht verändert werden. Die Betriebsarten Messen und Kalibrieren sind ohne Zugangsbeschränkung anwählbar. Betriebsebene: Konfiguration und Parametrierung können in der Betriebsebene ohne Codeeingabe abgefragt werden, während der Meßbetrieb weiterläuft. Die Einstellungen können jedoch nicht verändert werden. Die Betriebsarten Messen und Kalibrieren sind ohne Zugangsbeschränkung anwählbar. Parametrierebene: Hier werden Meßbereiche, Grenzwerte usw. eingegeben. Der Zugang ist über einen Code geschützt. Parametrierebene: Hier werden Meßbereiche, Grenzwerte usw. eingegeben. Der Zugang ist über einen Code geschützt. Konfigurationsebene: In dieser Ebene werden die Funktionen des Meßumformers festgelegt. Die Konfiguration erfolgt nach der Installation des Gerätes, meist nur bei der Erstinbetriebnahme. Der Zugang ist ebenfalls über einen Code geschützt. Konfigurationsebene: In dieser Ebene werden die Funktionen des Meßumformers festgelegt. Die Konfiguration erfolgt nach der Installation des Gerätes, meist nur bei der Erstinbetriebnahme. Der Zugang ist ebenfalls über einen Code geschützt. 11 11 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Beschreibung Beschreibung Hinweis: Nach einem Stromausfall kehrt das Gerät zum letzten Betriebszustand zurück. Alle Einstellungen bleiben erhalten. Hinweis: Nach einem Stromausfall kehrt das Gerät zum letzten Betriebszustand zurück. Alle Einstellungen bleiben erhalten. 12 12 Installation Oxi 170/ Oxi 296 Installation Allgemeine Hinweise • • • • Oxi 170/ Oxi 296 Allgemeine Hinweise Geräte, die im Freien installiert werden (Oxi 170), mit einem Schutzdach versehen (siehe WTW-Zubehör). Nach Installation des Oxi 170 den Gehäusedeckel schließen, um den IP66-Standard zu gewährleisten. Ein-/Ausgänge benötigen keinen zusätzlichen Blitzschutz. Erforderliche Blitzschutzmaßnahmen sind bereits im Meßumformer integriert, bestehende Blitzschutzmaßnahmen können zusätzlich benutzt werden. Die PG-Verschraubungen des Oxi 170 sind für Kabeldurchmesser von 10 bis 14 mm ausgelegt. Nichtbenutzte Kabeldurchführungen (PG-Verschraubungen) mit einem Abschlußnippel versehen, um den IP66-Standard zu gewährleisten. Netzanschluß • • • • Geräte, die im Freien installiert werden (Oxi 170), mit einem Schutzdach versehen (siehe WTW-Zubehör). Nach Installation des Oxi 170 den Gehäusedeckel schließen, um den IP66-Standard zu gewährleisten. Ein-/Ausgänge benötigen keinen zusätzlichen Blitzschutz. Erforderliche Blitzschutzmaßnahmen sind bereits im Meßumformer integriert, bestehende Blitzschutzmaßnahmen können zusätzlich benutzt werden. Die PG-Verschraubungen des Oxi 170 sind für Kabeldurchmesser von 10 bis 14 mm ausgelegt. Nichtbenutzte Kabeldurchführungen (PG-Verschraubungen) mit einem Abschlußnippel versehen, um den IP66-Standard zu gewährleisten. Netzanschluß Die Installation ausschließlich durch Elektrofachkräfte durchführen lassen, da es sich um lebensgefährliche Netzspannung handelt. Eine zweipolige Trennungsmöglichkeit zwischen Gerät und Netz vorsehen (z.B. Sicherung)! Die Geräte sind je nach Ausführung für 230 VAC, 115 VAC, 24 VAC oder 24 VDC ausgelegt. Die Netzspannung ist auf dem Typenschild abgedruckt. Vor Inbetriebnahme des Gerätes in jedem Fall überprüfen, ob die richtige Netzspannung anliegt. Eine falsche Netzspannung kann eine Beschädigung des Gerätes nach sich ziehen! Die Installation ausschließlich durch Elektrofachkräfte durchführen lassen, da es sich um lebensgefährliche Netzspannung handelt. Eine zweipolige Trennungsmöglichkeit zwischen Gerät und Netz vorsehen (z.B. Sicherung)! Die Geräte sind je nach Ausführung für 230 VAC, 115 VAC, 24 VAC oder 24 VDC ausgelegt. Die Netzspannung ist auf dem Typenschild abgedruckt. Vor Inbetriebnahme des Gerätes in jedem Fall überprüfen, ob die richtige Netzspannung anliegt. Eine falsche Netzspannung kann eine Beschädigung des Gerätes nach sich ziehen! Bei Geräten mit 24 V DC Modul folgendes beachten: Geräte nur an einer Spannungsquelle betreiben, die die Anforderungen an SELV (Safety Extra Low Voltage mit verstärkter Isolation zu gefährlichen Spannungen) gemäß EN 60950 erfüllt. Ohne Schnittstelle sollten die Anforderungen gemäß EN 61010-1 erfüllt werden. Bei Geräten mit 24 V DC Modul folgendes beachten: Geräte nur an einer Spannungsquelle betreiben, die die Anforderungen an SELV (Safety Extra Low Voltage mit verstärkter Isolation zu gefährlichen Spannungen) gemäß EN 60950 erfüllt. Ohne Schnittstelle sollten die Anforderungen gemäß EN 61010-1 erfüllt werden. Alle Geräte der Baureihe "170/296" sind gemäß Schutzklasse II ausgelegt, d.h. es wird kein Schutzleiteranschluß benötigt. Alle Geräte der Baureihe "170/296" sind gemäß Schutzklasse II ausgelegt, d.h. es wird kein Schutzleiteranschluß benötigt. Schutzleiter nicht in das Gerät führen bzw. an eine der Geräteklemmen oder Zuleitung anschließen! Die Gerätesicherung darf nur durch autorisierte WTW Fachkräfte gewechselt werden. Schutzleiter nicht in das Gerät führen bzw. an eine der Geräteklemmen oder Zuleitung anschließen! Die Gerätesicherung darf nur durch autorisierte WTW Fachkräfte gewechselt werden. 13 13 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Installation "SENS-CHECK" - Anschluß Installation "SENS-CHECK" - Anschluß Das "SENS-CHECK" - Relais ist als vom Gerät galvanisch getrennter Einschalter ausgelegt; es wird immer dann aktiv (= geschlossen), wenn ein Sensorfehler auftritt. Diese Meldung wird auch auf dem Display ausgegeben. Mit dem Relais können Sensorfehler in der Warte angezeigt werden. Das "SENS-CHECK" - Relais ist als vom Gerät galvanisch getrennter Einschalter ausgelegt; es wird immer dann aktiv (= geschlossen), wenn ein Sensorfehler auftritt. Diese Meldung wird auch auf dem Display ausgegeben. Mit dem Relais können Sensorfehler in der Warte angezeigt werden. Hinweis: Den Relaiskontakt nur mit max. 230 V AC / 5A, max. jedoch 150 W belasten. Hinweis: Den Relaiskontakt nur mit max. 230 V AC / 5A, max. jedoch 150 W belasten. REC 1 / REC 2 Anschlüsse REC 1 / REC 2 Anschlüsse Die Stromausgänge REC1 (O2) und REC 2 (Temperatur) sind folgendermaßen konfigurierbar: Die Stromausgänge REC1 (O2) und REC 2 (Temperatur) sind folgendermaßen konfigurierbar: • • • • 0 bis 20 mA 4 bis 20 mA Werden Endgeräte mit gemeinsamer Masse verwendet, auf die exakte Polung der Stromflussrichtung (+ / – ) achten. Es handelt sich um aktive Stromquellen, die keine externe Spannungsquelle benötigen! 0 bis 20 mA 4 bis 20 mA Werden Endgeräte mit gemeinsamer Masse verwendet, auf die exakte Polung der Stromflussrichtung (+ / – ) achten. Es handelt sich um aktive Stromquellen, die keine externe Spannungsquelle benötigen! Keine externe Spannungsquelle verwenden, da dies zu Fehlern bei den Stromausgängen führen kann! Bürde maximal 600 Ohm. K1 / K2 (Relaiskontakte) Keine externe Spannungsquelle verwenden, da dies zu Fehlern bei den Stromausgängen führen kann! Bürde maximal 600 Ohm. K1 / K2 (Relaiskontakte) Die Relaiskontakte K1 und K2 sind als potentialfreie Schließer ausgelegt. Über die Konfigurationsebene können diese Kontakte auch als Öffner konfiguriert werden. Die Zuordnung der Relais zu den entsprechenden Funktionen wird über die Softwarekonfiguration vorgenommen. Die Relaiskontakte K1 und K2 sind als potentialfreie Schließer ausgelegt. Über die Konfigurationsebene können diese Kontakte auch als Öffner konfiguriert werden. Die Zuordnung der Relais zu den entsprechenden Funktionen wird über die Softwarekonfiguration vorgenommen. Hinweis: Die Kontakte sind für 230 V AC / 5A, max. jedoch 150 W ausgelegt. Hinweis: Die Kontakte sind für 230 V AC / 5A, max. jedoch 150 W ausgelegt. 14 14 Installation Oxi 170/ Oxi 296 Installation Digitale Schnittstelle RS 485 (Option RS) Oxi 170/ Oxi 296 Digitale Schnittstelle RS 485 (Option RS) Die RS 485-Schnittstelle arbeitet mit störunanfälligen Differenzpegeln. Es können damit Kabellängen bis zu 1 km Länge realisiert werden. Die Geräte werden über eine 2-Draht-Leitung verbunden. Bei größeren Längen sowie einer größeren Anzahl von Geräten ist eine verdrillte 3-Draht-Leitung zu empfehlen; die dritte Leitung wird als Bezugspotential (GND) mitgeführt, um eventuell auftretende Potentialunterschiede auszugleichen. Die RS 485-Schnittstelle arbeitet mit störunanfälligen Differenzpegeln. Es können damit Kabellängen bis zu 1 km Länge realisiert werden. Die Geräte werden über eine 2-Draht-Leitung verbunden. Bei größeren Längen sowie einer größeren Anzahl von Geräten ist eine verdrillte 3-Draht-Leitung zu empfehlen; die dritte Leitung wird als Bezugspotential (GND) mitgeführt, um eventuell auftretende Potentialunterschiede auszugleichen. Jede Busleitung softwaremäßig mit einem Widerstand abschließen (siehe Parametrierung). Jede Busleitung softwaremäßig mit einem Widerstand abschließen (siehe Parametrierung). Das letzte Gerät auf der Busleitung muß den Abschlußwiderstand bereitstellen, d.h. bei der Parametrierung (PIF) muß beim letzten Gerät innerhalb des Bus-Verbands der Abschluß zugeschaltet (tr) und bei allen anderen Geräten abgeschaltet (notr) werden. Das letzte Gerät auf der Busleitung muß den Abschlußwiderstand bereitstellen, d.h. bei der Parametrierung (PIF) muß beim letzten Gerät innerhalb des Bus-Verbands der Abschluß zugeschaltet (tr) und bei allen anderen Geräten abgeschaltet (notr) werden. Wird nur ein Gerät verwendet, so stellt dieses das letzte Gerät dar und der Abschlußwiderstand muß zugeschaltet werden (tr). Alle anderen technischen Daten siehe Bedienungsanleitung RS 485. Wird nur ein Gerät verwendet, so stellt dieses das letzte Gerät dar und der Abschlußwiderstand muß zugeschaltet werden (tr). Alle anderen technischen Daten siehe Bedienungsanleitung RS 485. USA und Canada: Für Netzversorgung und Relais-/Alarmkontakte conduit box MCB 17x verwenden. Installationshinweise beachten. USA und Canada: Für Netzversorgung und Relais-/Alarmkontakte conduit box MCB 17x verwenden. Installationshinweise beachten. 15 15 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Installation Installation Installationshinweise Oxi 170 Installationshinweise Oxi 170 Klemmenbelegung Klemmenbelegung Klemme 1 2 3 4 5 6 7 8 9 10 11 12 13 Klemmenbelegung X1 A (Option RS 485) B (Option RS 485) GND (Option RS 485) Sens-Check Sens-Check K1 (Option R) K1 (Option R) K2 (Option R) K2 (Option R) N (Netz/Mains) L1 (Netz/Mains) – – Klemme X2 REC 1 + REC 1 – REC 2 + REC 2 – a (Sensor) b (Sensor) c (Sensor) d (Sensor) e (Sensor) f (Sensor) g (Sensor) h (Sensor) i (Sensor) 1 2 3 4 5 6 7 8 9 10 11 12 13 Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PG-Verschraubung abschneiden. Klemmenbelegung X1 A (Option RS 485) B (Option RS 485) GND (Option RS 485) Sens-Check Sens-Check K1 (Option R) K1 (Option R) K2 (Option R) K2 (Option R) N (Netz/Mains) L1 (Netz/Mains) – – X2 REC 1 + REC 1 – REC 2 + REC 2 – a (Sensor) b (Sensor) c (Sensor) d (Sensor) e (Sensor) f (Sensor) g (Sensor) h (Sensor) i (Sensor) Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PG-Verschraubung abschneiden. Hinweis: Bei Stromversorgung über 24 VDC folgende Verdrahtung verwenden: L1 + 24 V N GND Hinweis: Bei Stromversorgung über 24 VDC folgende Verdrahtung verwenden: L1 + 24 V N GND 16 16 Oxi 170/ Oxi 296 Installation Oxi 170/ Oxi 296 Installation Anschluß von Sensoren TriOxmatic® 690, TriOxmatic® 70x Anschluß von Sensoren TriOxmatic® 690, TriOxmatic® 70x Oxi 170 Oxi 170 17 17 Oxi 170/ Oxi 296 Anschluß des Klemmkastens KI/S 1413 1)99 Oxi 170/ Oxi 296 Installation Anschluß des Klemmkastens KI/S 1413 S/c 1)99 C K 160 S/c C K 160 KI/S EK/AG oder EK 170 Max. Kabellänge 100 m KI/S EK/AG oder EK 170 Max. Kabellänge 100 m TriOxmatic® 690, TriOxmatic® 70x 18 Installation TriOxmatic® 690, TriOxmatic® 70x 18 Oxi 170/ Oxi 296 Installation Verdrahtung KI/S 12 34567 Oxi 170/ Oxi 296 Installation Verdrahtung KI/S Klemmleiste Adernfarbe Klemmleiste Adernfarbe 1 2 3 4 5 6 7 gelb grau + Schirm rosa blau braun grün weiß 1 2 3 4 5 6 7 gelb grau + Schirm rosa blau braun grün weiß 12 34567 Hinweis: Nach Anschluß des 8-adrigen EK 170-Kabels bleibt 1 Ader übrig. Die nicht verwendete “Ader“ fixieren oder abzwicken. Hinweis: Nach Anschluß des 8-adrigen EK 170-Kabels bleibt 1 Ader übrig. Die nicht verwendete “Ader“ fixieren oder abzwicken. Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PGVerschraubung abschneiden. Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PGVerschraubung abschneiden. 19 19 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Installation Installation Installationshinweise Oxi 296 Installationshinweise Oxi 296 Klemmenbelegung Klemmenbelegung Digitale Schnittstelle RS 485 A B GND Digitale Schnittstelle RS 485 Schreiberausgänge Sens-Check Kontaktausgänge 1 2 3 4 5 6 7 8 9 10 11 12 13 Sensor Relais 2 Stromversorgung N L1 + AC DC Klemmenbelegung X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relais 1 Relais 1 Relais 2 Relais 2 N (Netz) L1 (Netz) – – Relais 1 Sensor Relais 2 Klemme Schreiberausgänge Sens-Check Kontaktausgänge Relais 1 Stromversorgung A B GND N L1 + AC DC Klemme X2 REC 1 + REC 1 – REC 2 + REC 2 – a (Sensor) b (Sensor) c (Sensor) d (Sensor) e (Sensor) f (Sensor) g (Sensor) h (Sensor) i (Sensor) 1 2 3 4 5 6 7 8 9 10 11 12 13 Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PG-Verschraubung abschneiden. Klemmenbelegung X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relais 1 Relais 1 Relais 2 Relais 2 N (Netz) L1 (Netz) – – X2 REC 1 + REC 1 – REC 2 + REC 2 – a (Sensor) b (Sensor) c (Sensor) d (Sensor) e (Sensor) f (Sensor) g (Sensor) h (Sensor) i (Sensor) Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PG-Verschraubung abschneiden. Hinweis: Bei Stromversorgung über 24 VDC folgende Verdrahtung verwenden: L1 +24 N GND GND Hinweis: Bei Stromversorgung über 24 VDC folgende Verdrahtung verwenden: L1 +24 N GND 20 20 Oxi 170/ Oxi 296 Installation TriOxmatic® 690, TriOxmatic® 70x anschließen TriOxmatic® 690, TriOxmatic® 70x anschließen Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PGVerschraubung abschneiden. Klemme 1 2 3 4 5 6 7 8 9 10 11 12 13 Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PGVerschraubung abschneiden. Klemmenbelegung X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relais 1 Relais 1 Relais 2 Relais 2 N (Netz) L1 (Netz) – – Oxi 170/ Oxi 296 Installation Klemme X2 REC 1 + REC 1 – REC 2 + REC 2 – gelb grün braun rosa – blau schwarz weiß – 1 2 3 4 5 6 7 8 9 10 11 12 13 21 Klemmenbelegung X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relais 1 Relais 1 Relais 2 Relais 2 N (Netz) L1 (Netz) – – X2 REC 1 + REC 1 – REC 2 + REC 2 – gelb grün braun rosa – blau schwarz weiß – 21 Oxi 170/ Oxi 296 Anschluß des Klemmkastens KI/S X1 Oxi 170/ Oxi 296 Installation Anschluß des Klemmkastens KI/S X2 X1 1 2 3 4 5 6 7 8 9 10 1 11 12 13 2 3 4 5 6 7 8 9 10 11 gelb grün braun rosa --blau grau + Schirm X2 1 2 3 4 5 6 7 8 9 10 1 11 12 13 weiß Kabel EK/AG oder EK 170 Installation 2 3 4 5 6 7 8 9 10 11 max. Kabellänge 100 m gelb grün braun rosa --blau grau + Schirm weiß Kabel EK/AG oder EK 170 KI/S KI/S Anschließbar: TriOxmatic® 690 oder TriOxmatic® 70x Anschließbar: TriOxmatic® 690 oder TriOxmatic® 70x Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PG-Verschraubung abschneiden. Klemme 1 2 3 4 5 6 7 8 9 10 11 12 13 22 Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PG-Verschraubung abschneiden. Klemmenbelegung X1 A (RS 485) B (RS 485) GND (RS 485) Relais 1 Relais 1 Relais 2 Relais 2 N (Netz) L1 (Netz) max. Kabellänge 100 m Klemme X2 REC 1 + REC 1 – REC 2 + REC 2 – gelb grün braun rosa blau grau + Schirm weiß 1 2 3 4 5 6 7 8 9 10 11 12 13 22 Klemmenbelegung X1 A (RS 485) B (RS 485) GND (RS 485) Relais 1 Relais 1 Relais 2 Relais 2 N (Netz) L1 (Netz) X2 REC 1 + REC 1 – REC 2 + REC 2 – gelb grün braun rosa blau grau + Schirm weiß Oxi 170/ Oxi 296 Installation Oxi 170/ Oxi 296 Installation Verdrahtung KI/S Verdrahtung KI/S Klemmleiste Adernfarbe Klemmleiste Adernfarbe 1 2 3 4 5 6 7 gelb grau + Schirm rosa blau braun grün weiß 1 2 3 4 5 6 7 gelb grau + Schirm rosa blau braun grün weiß Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PGVerschraubung abschneiden. Hinweis: Nach Anschluß des 8-adrigen EK 170-Kabels bleibt 1 Ader übrig. Die nicht verwendete “Ader“ fixieren oder abzwicken. Nichtbenutzte Adern dürfen nicht in das Gehäuse ragen. Ansonsten können Funktionsstörungen auftreten. Dies gilt insbesondere für den Schutzleiter der Netzzuleitung. Nichtbenutzte Adern im Gehäuse möglichst nahe an der PGVerschraubung abschneiden. Hinweis: Nach Anschluß des 8-adrigen EK 170-Kabels bleibt 1 Ader übrig. Die nicht verwendete “Ader“ fixieren oder abzwicken. 23 23 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Konfiguration Die Konfiguration legt die Arbeitsweise des Gerätes fest. Die Konfigurationsebene ist dazu in Untermenüs aufgeteilt (siehe Ablaufdiagramm). In den Untermenüs werden nur diejenigen Einstellmöglichkeiten angeboten, die auf Grund der vorherigen Konfiguration vom Programm noch nicht automatisch festgelegt wurden. Über einen Code kann der Zugang zur Konfigurationsebene geschützt werden. Die Konfiguration legt die Arbeitsweise des Gerätes fest. Die Konfigurationsebene ist dazu in Untermenüs aufgeteilt (siehe Ablaufdiagramm). In den Untermenüs werden nur diejenigen Einstellmöglichkeiten angeboten, die auf Grund der vorherigen Konfiguration vom Programm noch nicht automatisch festgelegt wurden. Über einen Code kann der Zugang zur Konfigurationsebene geschützt werden. Die Konfiguration im betriebsbereiten Zustand vornehmen, d.h.: Der Meßumformer ist an der Versorgungsspannung angeschlossen, die Meßsonde ist angeschlossen. Werkseinstellungen Konfiguration Die Konfiguration im betriebsbereiten Zustand vornehmen, d.h.: Der Meßumformer ist an der Versorgungsspannung angeschlossen, die Meßsonde ist angeschlossen. Werkseinstellungen Einstellbare Funktion Einstellung Menüpunkt Einstellbare Funktion Einstellung Menüpunkt Salinitätskorrektur OFF CSA Salinitätskorrektur OFF CSA Meßwertgeber 690 CIN Meßwertgeber 690 CIN Meßbereichsendwert 60,0 mg/l Crn Meßbereichsendwert 60,0 mg/l Crn Meßbereich Schreiberausgang 1 0,0 ... 60,0 mg/l CR1 Meßbereich Schreiberausgang 1 0,0 ... 60,0 mg/l CR1 CR2 Temperaturbereich Schreiberausgang 21) 0,0 ... 50,0 °C nF REL1 Relaisfunktion2) (keine Funktion Rel. 1) nF REL2 (keine Funktion Rel. 2) Temperaturbereich Schreiberausgang 21) 0,0 ... 50,0 °C nF REL1 Relaisfunktion2) (keine Funktion Rel. 1) nF REL2 (keine Funktion Rel. 2) CRC 1) nur bei T-Option 1) nur bei T-Option 2) nur bei Relais-Option 2) nur bei Relais-Option 24 24 CR2 CRC Konfiguration Oxi 170/ Oxi 296 Konfiguration Konfigurationsebene aufrufen Oxi 170/ Oxi 296 Konfigurationsebene aufrufen − Taste DOWN drücken. − Taste DOWN drücken. − Taste ENTER drücken. − Taste ENTER drücken. Im Display erscheint: Im Display erscheint: Die erste Ziffer blinkt. Die erste Ziffer blinkt. Im Auslieferzustand ist keine Codezahl eingestellt. Der Zugang zur Konfigurationsebene erfolgt durch − 3 maliges Drücken der Taste ENTER. Im Auslieferzustand ist keine Codezahl eingestellt. Der Zugang zur Konfigurationsebene erfolgt durch − 3 maliges Drücken der Taste ENTER. Wurde bei einer früheren Parametrierung bereits eine Codezahl eingestellt, folgendermaßen vorgehen: Wurde bei einer früheren Parametrierung bereits eine Codezahl eingestellt, folgendermaßen vorgehen: − Die erste Ziffer mit den Tasten UP / DOWN einstellen. − Die erste Ziffer mit den Tasten UP / DOWN einstellen. − Mit ENTER bestätigen. − Mit ENTER bestätigen. − Die beiden weiteren Ziffern in gleicher Weise einstellen. − Die beiden weiteren Ziffern in gleicher Weise einstellen. Es erscheint folgende Anzeige: Es erscheint folgende Anzeige: − Mit den Tasten UP / DOWN zu C0 (Konfiguration) wechseln. − Mit den Tasten UP / DOWN zu C0 (Konfiguration) wechseln. − Mit ENTER bestätigen. − Mit ENTER bestätigen. Bei falscher Codeeingabe bzw. nach Drücken der Taste ESCAPE erfolgt der Zugang zur Konfiguration im Betrachter-Modus. D.h. Einstellungen können überprüft, aber nicht geändert werden. Bei falscher Codeeingabe bzw. nach Drücken der Taste ESCAPE erfolgt der Zugang zur Konfiguration im Betrachter-Modus. D.h. Einstellungen können überprüft, aber nicht geändert werden. 25 25 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Konfiguration Übersichtstabelle der Untermenüs Anzeige Übersichtstabelle der Untermenüs Beschreibung Grundgerät CSA Salinitätskorrektur CIn Meßwertgeber auswählen Crn Meßbereichsendwert auswählen CR1 Recorder 1 auswählen CR2 Recorder 2 auswählen Option Relais T-Option + + + + Zuordnung der Melderelais CRF Konfiguration Betriebsart der Melderelais + + + Anzeige Beschreibung Grundgerät CSA Salinitätskorrektur CIn Meßwertgeber auswählen Crn Meßbereichsendwert auswählen CR1 Recorder 1 auswählen CR2 Recorder 2 auswählen + + + + Zuordnung der Melderelais CRF Option Relais T-Option Betriebsart der Melderelais + Menü erscheint bei der entsprechenden Geräteausführung. + Menü erscheint bei der entsprechenden Geräteausführung. 26 26 + + + Konfiguration Oxi 170/ Oxi 296 Konfiguration Salinitätskorrektur Salinitätskorrektur Im Untermenü CSA wird die Salinitätskorrektur ein- bzw. ausgeschaltet: • • Oxi 170/ Oxi 296 Korrektur EIN 0n Korrektur AUS 0FF (Auslieferungszustand) Im Untermenü CSA wird die Salinitätskorrektur ein- bzw. ausgeschaltet: • • Hinweis: Das Menü Salinitätskorrektur legt fest, ob prinzipiell eine Salinitätskorrektur erfolgen soll. Wird diese eingeschaltet (ON), so kann in der Parametrierung (PSA) eine Eingabe erfolgen. Korrektur EIN 0n Korrektur AUS 0FF (Auslieferungszustand) Hinweis: Das Menü Salinitätskorrektur legt fest, ob prinzipiell eine Salinitätskorrektur erfolgen soll. Wird diese eingeschaltet (ON), so kann in der Parametrierung (PSA) eine Eingabe erfolgen. − Mit den Tasten UP / DOWN zwischen CSA 0n und CSA 0FF wählen. − Mit den Tasten UP / DOWN zwischen CSA 0n und CSA 0FF wählen. − Mit der Taste ENTER weiter zu CIn. − Mit der Taste ENTER weiter zu CIn. 27 27 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Konfiguration Sensoren auswählen Sensoren auswählen Folgende Einstellmöglichkeiten sind anwählbar: Anzeige Sensor 690 TriOxmatic® 690 ohne 700 TriOxmatic® 700 mit 701 TriOxmatic® 701 CellOx 700 − − mit Folgende Einstellmöglichkeiten sind anwählbar: Anzeige Sensor REG und LECK-Erkennung 690 TriOxmatic® 690 ohne REG und LECK-Erkennung REG und LECK-Erkennung 700 TriOxmatic® 700 mit REG und LECK-Erkennung 701 TriOxmatic® 701 mit REG und LECK-Erkennung REG und LECK-Erkennung Durch Drücken der Tasten UP / DOWN einen Sensor auswählen. Mit der Taste ENTER bestätigen. CIn Konfiguration CellOx 700 − − Beispiel: TriOxmatic® 690 Durch Drücken der Tasten UP / DOWN einen Sensor auswählen. Mit der Taste ENTER bestätigen. CIn 690 Beispiel: TriOxmatic® 690 690 Hinweis: Das Gerät ist mit einer REG und LECK-Erkennung ausgestattet, die einen Sensordefekt bzw. eine fällige Wartung anzeigt. Hinweis: Das Gerät ist mit einer REG und LECK-Erkennung ausgestattet, die einen Sensordefekt bzw. eine fällige Wartung anzeigt. 28 28 Oxi 170/ Oxi 296 Konfiguration Auswahl Meßbereich Auswahl Meßbereich Im Untermenü Crn gibt es folgende Einstellmöglichkeiten: • • • • 60,0 mg/l 20,00 mg/l 600 % 200,0 % Oxi 170/ Oxi 296 Konfiguration Im Untermenü Crn gibt es folgende Einstellmöglichkeiten: • • • • (nur bei TriOxmatic 701) (nur bei TriOxmatic 701) Im Menü Crn stehen folgende Meßbereiche in Abhängigkeit vom Sensortyp zur Auswahl: 60,0 mg/l 20,00 mg/l 600 % 200,0 % (nur bei TriOxmatic 701) (nur bei TriOxmatic 701) Im Menü Crn stehen folgende Meßbereiche in Abhängigkeit vom Sensortyp zur Auswahl: MBE 20.00 mg/l 690 700 701 x MBE 20.00 mg/l 690 700 701 x 60.0 mg/l x x x 60.0 mg/l x x x x 200.0 % x x x 600 % x x x 200.0 % 600 % Crn 6=0 − − Mit den Tasten UP/DOWN den Meßbereich auswählen. Mit ENTER bestätigen. Crn 6=0 29 x − − Mit den Tasten UP/DOWN den Meßbereich auswählen. Mit ENTER bestätigen. 29 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Konfiguration Auswahl Schreiberausgang REC 1 Auswahl Schreiberausgang REC 1 Bei Schreiberbereichsüberschreitungen (OFL) geben die Schreiberausgänge ein konstantes Signal von 20,5 mA aus. Die Rückkehr zum eingestellten Schreiberbereich erfolgt automatisch nach Aufhebung der Schreiberbereichsüberschreitung. Zulässige Schreiberbereiche in Abhängigkeit vom Meßbereich: Meßbereiche REC - Bereiche Minimum (Meßbereichs-Anfang MBA) Maximum (Meßbereichs-Ende MBE) D/span (Einstellschrittweite) *) Bei Schreiberbereichsüberschreitungen (OFL) geben die Schreiberausgänge ein konstantes Signal von 20,5 mA aus. Die Rückkehr zum eingestellten Schreiberbereich erfolgt automatisch nach Aufhebung der Schreiberbereichsüberschreitung. Zulässige Schreiberbereiche in Abhängigkeit vom Meßbereich: 200 % variabel 0,0 % 600 % variabel 0% 20,00 mg/l variabel 0,00 mg/l 60,0 mg/l variabel 0,0 mg/l 100,0 % bis 200,0 % *) 100 % bis 600 % *) 2,00 mg/l bis 20,00 mg/l *) 5,0 mg/l bis 60,0 mg/l *) 10,0 % 100 % 1,00 mg/l 5,0 mg/l Vorgabe-Einstellungen Meßbereiche REC - Bereiche Minimum (Meßbereichs-Anfang MBA) Maximum (Meßbereichs-Ende MBE) D/span (Einstellschrittweite) *) Einstellung bei CrI: CrI Konfiguration 200 % variabel 0,0 % 600 % variabel 0% 20,00 mg/l variabel 0,00 mg/l 60,0 mg/l variabel 0,0 mg/l 100,0 % bis 200,0 % *) 100 % bis 600 % *) 2,00 mg/l bis 20,00 mg/l *) 5,0 mg/l bis 60,0 mg/l *) 10,0 % 100 % 1,00 mg/l 5,0 mg/l Vorgabe-Einstellungen Einstellung bei CrI: − − Durch Drücken der Tasten UP / DOWN die Schreiberbereichsobergrenze einstellen. Mit ENTER bestätigen. CrI − − Durch Drücken der Tasten UP / DOWN die Schreiberbereichsobergrenze einstellen. Mit ENTER bestätigen. Hinweis: Der untere Schreiberbereichsendwert ist fest auf 0 mg/l eingestellt. Hinweis: Der untere Schreiberbereichsendwert ist fest auf 0 mg/l eingestellt. 30 30 Konfiguration Oxi 170/ Oxi 296 Konfiguration Auswahl Schreiberausgang REC 2 (nur T-Option) Auswahl Schreiberausgang REC 2 (nur T-Option) Bei Schreiberbereichsüberschreitungen (OFL) geben die Schreiberausgänge ein konstantes Signal von 20,5 mA aus. Die Rückkehr zum eingestellten Schreiberbereich erfolgt automatisch nach Aufhebung der Schreiberbereichsüberschreitung. Zulässige Schreiberbereiche: Meßbereiche REC - Bereiche Minimum (Meßbereichs-Anfang MBA) Maximum (Meßbereichs-Ende MBE) Schreiberbereich-Umfang D/span (Einstellschrittweite) *) **) Oxi 170/ Oxi 296 Bei Schreiberbereichsüberschreitungen (OFL) geben die Schreiberausgänge ein konstantes Signal von 20,5 mA aus. Die Rückkehr zum eingestellten Schreiberbereich erfolgt automatisch nach Aufhebung der Schreiberbereichsüberschreitung. Zulässige Schreiberbereiche: -5 ... +100 variabel -5 °C *) bis + 80 °C 25 °C bis 100 °C **) mind. 20 °C max. 105 °C 1 °C Meßbereiche REC - Bereiche Minimum (Meßbereichs-Anfang MBA) Maximum (Meßbereichs-Ende MBE) Schreiberbereich-Umfang D/span (Einstellschrittweite) Vorgabe-Einstellung: 0 °C Vorgabe-Einstellung: 50 °C *) **) Einstellung: -5 ... +100 variabel -5 °C *) bis + 80 °C 25 °C bis 100 °C **) mind. 20 °C max. 105 °C 1 °C Vorgabe-Einstellung: 0 °C Vorgabe-Einstellung: 50 °C Einstellung: − Cr2 − Durch Drücken der Tasten UP / DOWN den oberen Wert ändern. Mit ENTER bestätigen. Cr2 °C − Durch Drücken der Tasten UP / DOWN den oberen Wert ändern. Mit ENTER bestätigen. °C Es erscheint der eingestellte untere Wert: − Cr2 − − Es erscheint der eingestellte untere Wert: Durch Drücken der Tasten UP / DOWN den unteren Wert ändern. Mit ENTER bestätigen. − Cr2 °C − Durch Drücken der Tasten UP / DOWN den unteren Wert ändern. Mit ENTER bestätigen. °C 31 31 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Konfiguration Konfiguration Relais 1 / Relais 2 (Option R) Relais 1 / Relais 2 (Option R) Relaisfunktionen auswählen Relaisfunktionen auswählen Jedem Relais kann eine Funktion zugeordnet werden: Jedem Relais kann eine Funktion zugeordnet werden: Funktion Erklärung Funktion Erklärung nF (no Funktion) Relais ohne Funktion nF (no Funktion) Relais ohne Funktion PS (power supply) Kontakt ist bei anliegendem Netz geschlossen und öffnet bei Netzausfall PS (power supply) Kontakt ist bei anliegendem Netz geschlossen und öffnet bei Netzausfall FrC (freeze) wird bei eingefrorenem Meßwert aktiv - z.B. beim Kalibrieren FrC (freeze) wird bei eingefrorenem Meßwert aktiv - z.B. beim Kalibrieren (limits) CS (cleaning system) 32 (limits) arbeitet als oberer/ unterer Grenzwertmelder und wird beim Über-/Unterschreiten des Sollwertes aktiv Relais zur periodischen Steuerung einer externen Sensor-Reinigungseinheit. Das Relais arbeitet als Schließer. Während des Reinigungsvorgangs bleibt der Meßwert eingefroren. CS (cleaning system) 32 arbeitet als oberer/ unterer Grenzwertmelder und wird beim Über-/Unterschreiten des Sollwertes aktiv Relais zur periodischen Steuerung einer externen Sensor-Reinigungseinheit. Das Relais arbeitet als Schließer. Während des Reinigungsvorgangs bleibt der Meßwert eingefroren. Konfiguration Oxi 170/ Oxi 296 Konfiguration Reglersignale Reglersignale Grenzwertmelder (UL.LL) Grenzwertmelder (UL.LL) Folgende Funktionen können angewählt werden: Funktion UL O2 LL O2 UL °C LL °C Oxi 170/ Oxi 296 Folgende Funktionen können angewählt werden: Erklärung oberer Grenzwert – Hauptparameter unterer Grenzwert – Hauptparameter oberer Grenzwert – Temperatur unterer Grenzwert – Temperatur Funktion UL O2 LL O2 UL °C LL °C Einstellung: Erklärung oberer Grenzwert – Hauptparameter unterer Grenzwert – Hauptparameter oberer Grenzwert – Temperatur unterer Grenzwert – Temperatur Einstellung: REL1 O2 REL1 − Durch Drücken der Tasten UP / DOWN die Relaisfunktion .LL auswählen, z. B. für Relais 1. − Mit ENTER bestätigen. − Durch Drücken der Tasten UP / DOWN die gewünschte Grenzwertfunktion auswählen, O2 für Relais 1. z. B. − Mit ENTER bestätigen. REL1 O2 REL1 Schaltrichtung (Öffner / Schließer) für FrC, UL.LL auswählen − Durch Drücken der Tasten UP / DOWN die Relaisfunktion .LL auswählen, z. B. für Relais 1. − Mit ENTER bestätigen. − Durch Drücken der Tasten UP / DOWN die gewünschte Grenzwertfunktion auswählen, O2 für Relais 1. z. B. − Mit ENTER bestätigen. Schaltrichtung (Öffner / Schließer) für FrC, UL.LL auswählen Im Untermenü CrF wird festgelegt, ob ein Relais als Öffner oder Schließer arbeitet. Im Untermenü CrF wird festgelegt, ob ein Relais als Öffner oder Schließer arbeitet. − Taste ENTER drücken, um in das Untermenü CrF einzusteigen. − Taste ENTER drücken, um in das Untermenü CrF einzusteigen. − Mit UP / DOWN wählen zwischen: SCHLIESSER (C = Close) OEFFNER (O = Open) − Mit UP / DOWN wählen zwischen: SCHLIESSER (C = Close) OEFFNER (O = Open) − Mit der Taste ENTER bestätigen. − Mit der Taste ENTER bestätigen. − In gleicher Weise die Einstellung für − In gleicher Weise die Einstellung für Relais 2 vornehmen. Relais 2 vornehmen. 33 33 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Parametrierung Die Parametrierung legt zahlenmäßig die Werte der Funktionen fest, für die das Gerät konfiguriert ist. Werkseinstellungen Parametrierung Die Parametrierung legt zahlenmäßig die Werte der Funktionen fest, für die das Gerät konfiguriert ist. Werkseinstellungen Einstellbare Funktion Einstellung Menüpunkt Einstellbare Funktion Einstellung Menüpunkt Salinitätskorrektur 2.0 PSA Salinitätskorrektur 2.0 PSA Schreiberausgang 1: Strombereich /Dämpfung 4 ... 20 mA / 20mA/s PR1 Schreiberausgang 1: Strombereich /Dämpfung 4 ... 20 mA / 20mA/s PR1 Schreiberausgang 2: Strombereich/Dämpfung Luftkorrektur 4 ... 20 mA / 20 mA/S PR2 4 ... 20 mA / 20 mA/S PR2 950 mbar PPr Schreiberausgang 2: Strombereich/Dämpfung Luftkorrektur 950 mbar PPr Einstellungen der Digitalschnittstelle RS 4851) SLAVE 9600 Bd Ident 01 8 no (8 Bit, no Parity) Abschluß aus P1F Einstellungen der Digitalschnittstelle RS 4851) SLAVE 9600 Bd Ident 01 8 no (8 Bit, no Parity) Abschluß aus P1F Paßzahl (Code) 000 PCD Paßzahl (Code) 000 PCD Temperatur-Nullpunktverschiebung 0,0 °C Pt Temperatur-Nullpunktverschiebung 0,0 °C Pt 1) nur bei RS-Option 1) nur bei RS-Option 34 34 Parametrierung Oxi 170/ Oxi 296 Parametrierung Parametrierebene aufrufen Oxi 170/ Oxi 296 Parametrierebene aufrufen − Taste DOWN drücken. − Taste DOWN drücken. − Taste ENTER drücken. − Taste ENTER drücken. Im Display erscheint: Im Display erscheint: Die erste Ziffer blinkt. Die erste Ziffer blinkt. Im Auslieferzustand ist keine Codezahl eingestellt. Der Zugang zur Konfigurationsebene erfolgt durch − 3 maliges Drücken der Taste ENTER. Im Auslieferzustand ist keine Codezahl eingestellt. Der Zugang zur Konfigurationsebene erfolgt durch − 3 maliges Drücken der Taste ENTER. Wurde bei einer früheren Parametrierung bereits eine Codezahl eingestellt, folgendermaßen vorgehen: Wurde bei einer früheren Parametrierung bereits eine Codezahl eingestellt, folgendermaßen vorgehen: − − − − Die erste Ziffer mit den Tasten UP / DOWN einstellen. Mit der Taste ENTER bestätigen. Die beiden weiteren Ziffern in gleicher Weise einstellen. Es erscheint folgende Anzeige: − − Die erste Ziffer mit den Tasten UP / DOWN einstellen. Mit der Taste ENTER bestätigen. Die beiden weiteren Ziffern in gleicher Weise einstellen. Es erscheint folgende Anzeige: − − Mit der Taste ENTER bestätigen. Mit der Taste ENTER bestätigen. Bei falscher Codeeingabe bzw. nach Drücken der Taste ESCAPE erfolgt der Zugang zur Konfiguration im Betrachter-Modus. D.h. Einstellungen können überprüft, aber nicht geändert werden. Bei falscher Codeeingabe bzw. nach Drücken der Taste ESCAPE erfolgt der Zugang zur Konfiguration im Betrachter-Modus. D.h. Einstellungen können überprüft, aber nicht geändert werden. 35 35 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Parametrierung Übersichtstabelle der Untermenüs Anzeige Übersichtstabelle der Untermenüs Beschreibung Optionen PSA Eingabe Salinität 1) Grundgerät + PrI Schreiberausgang 1 + Pr2 Schreiberausgang 2 PL Grenzwertmelder PPr Eingabe des aktuellen Luftdrucks PIF Schnittstelle RS 485 Pt PCS Parametrierung Relais Anzeige + + + + Temperaturabgleich + Timer für externe SensorReinigungseinheit Optionen T-Option RS 485 + Anlegen der Paßzahl Beschreibung PSA Eingabe Salinität 1) Grundgerät + PrI Schreiberausgang 1 + Pr2 Schreiberausgang 2 PL Grenzwertmelder PPr Eingabe des aktuellen Luftdrucks PIF Schnittstelle RS 485 Pt PCS + Relais T-Option RS 485 + + + + Anlegen der Paßzahl + Temperaturabgleich + Timer für externe SensorReinigungseinheit + + Menü erscheint bei der entsprechenden Geräteausführung. 1) Erscheint nur bei Einstellung ( CSA 0n) Der Ablauf der Parametrierung ist aus dem graphischen Ablaufschema ersichtlich . + Menü erscheint bei der entsprechenden Geräteausführung. 1) Erscheint nur bei Einstellung ( CSA 0n) Der Ablauf der Parametrierung ist aus dem graphischen Ablaufschema ersichtlich . Parametrierung Salinität (nur wenn CSA 0n) Parametrierung Salinität (nur wenn CSA 0n) Korrektur der Sauerstoffmessung in Abhängigkeit vom Salzgehalt des Meßgutes. Korrektur der Sauerstoffmessung in Abhängigkeit vom Salzgehalt des Meßgutes. − − Taste ENTER drücken, es erscheint das Untermenü PSA: PSA "0 − Mit den Tasten UP / DOWN den Wert zwischen 2.0 und 70.0 einstellen (entspricht 3,4 mS/cm ... 86,2 mS/cm bei Tref 20°). − Mit der Taste ENTER bestätigen. PSA "0 Hinweis: 36 Taste ENTER drücken, es erscheint das Untermenü PSA: − Mit den Tasten UP / DOWN den Wert zwischen 2.0 und 70.0 einstellen (entspricht 3,4 mS/cm ... 86,2 mS/cm bei Tref 20°). − Mit der Taste ENTER bestätigen. Hinweis: 36 Parametrierung Oxi 170/ Oxi 296 Parametrierung Schreiberausgang REC 1 und REC 2 Schreiberausgang REC 1 und REC 2 Dieses Untermenü erlaubt die Einstellung von: Dieses Untermenü erlaubt die Einstellung von: • • • Strombereich − 0 bis 20 mA − 4 bis 20 mA • Dämpfung [dI/dt.] (dI = Stromänderung; dt = Zeitänderung) − 0,1 mA/s − 1 mA/s − 5 mA/s − 20 mA/s (= Auslieferungszustand) Hinweis: Dämpfung = Änderungsgeschwindigkeit des Recorder-Stromes [mA/sec] bei sprunghafter Änderung des Eingangssignals. Strombereich − 0 bis 20 mA − 4 bis 20 mA Dämpfung [dI/dt.] (dI = Stromänderung; dt = Zeitänderung) − 0,1 mA/s − 1 mA/s − 5 mA/s − 20 mA/s (= Auslieferungszustand) Hinweis: Dämpfung = Änderungsgeschwindigkeit des Recorder-Stromes [mA/sec] bei sprunghafter Änderung des Eingangssignals. Einstellung: Einstellung: − − Taste ENTER drücken, es erscheint das Untermenü Pr1: Taste ENTER drücken, es erscheint das Untermenü Pr1: − Mit den Tasten UP / DOWN den Strombereich wählen. − Mit den Tasten UP / DOWN den Strombereich wählen. − Mit der Taste ENTER bestätigen. − Mit der Taste ENTER bestätigen. − − − Oxi 170/ Oxi 296 − Mit den Tasten UP / DOWN die Dämpfung wählen. Mit der Taste ENTER bestätigen. − − Taste ENTER drücken, es erscheint das Untermenü Pr2: Mit den Tasten UP / DOWN die Dämpfung wählen. Mit der Taste ENTER bestätigen. Taste ENTER drücken, es erscheint das Untermenü Pr2: − Schreiberausgang 2 in gleicher Weise wie Schreiberausgang 1 einstellen. − Schreiberausgang 2 in gleicher Weise wie Schreiberausgang 1 einstellen. − Mit der Taste ENTER bestätigen. − Mit der Taste ENTER bestätigen. 37 37 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Parametrierung Parametrierung Relais 1 / Relais 2 (Geräteausführung R) Relais 1 / Relais 2 (Geräteausführung R) Grenzwertmelder (UL.LL) Grenzwertmelder (UL.LL) Das Untermenü PL erlaubt die Festlegung folgender Werte für die in der Konfigurationsebene mit einer Grenzwertfunktion (UL.LL) belegten Relais: 1. Grenzwert L (Limit) 2. Hysterese HS (Hysterese) 3. Verzögerungszeit Td (Time-Delay) Das Untermenü PL erlaubt die Festlegung folgender Werte für die in der Konfigurationsebene mit einer Grenzwertfunktion (UL.LL) belegten Relais: 1. Grenzwert L (Limit) 2. Hysterese HS (Hysterese) 3. Verzögerungszeit Td (Time-Delay) Im Untermenü PL erscheinen nur die Grenzwertfunktionen (UL oder LL), die bei der Konfiguration des Gerätes ausgewählt wurden ). (Konfigurationsebene ⇒ Untermenü Übersichtstabelle: Soll Hysterese Verzögerungszeit Im Untermenü PL erscheinen nur die Grenzwertfunktionen (UL oder LL), die bei der Konfiguration des Gerätes ausgewählt wurden ). (Konfigurationsebene ⇒ Untermenü Übersichtstabelle: Minimum: Maximum: Einstellgenauigkeit: unterer Meßbereichsendwert (UBE) oberer Meßbereichsendwert (OBE) entsprechend der Meßwertanzeige Vorgabe: bei oberen Grenzwerten das Maximum, sonst das Minimum Minimum: Maximum: Einstellgenauigkeit: 0 10% vom Meßbereich (OBE - UBE) entsprechend der Meßwertanzeige Vorgabe: 0 Minimum: Maximum: Einstellschritte: 0 sec 59 min 59 sec 1 sec Vorgabe: 0 sec Soll Hysterese Verzögerungszeit Minimum: Maximum: Einstellgenauigkeit: unterer Meßbereichsendwert (UBE) oberer Meßbereichsendwert (OBE) entsprechend der Meßwertanzeige Vorgabe: bei oberen Grenzwerten das Maximum, sonst das Minimum Minimum: Maximum: Einstellgenauigkeit: 0 10% vom Meßbereich (OBE - UBE) entsprechend der Meßwertanzeige Vorgabe: 0 Minimum: Maximum: Einstellschritte: 0 sec 59 min 59 sec 1 sec Vorgabe: 0 sec Soll: Eingestellter oberer bzw. unterer Grenzwert (Sollwert). Über- bzw. unterschreitet das Meßsignal diesen Wert, schaltet das zugehörige, als Grenzkontakt programmierte Relais. Soll: Eingestellter oberer bzw. unterer Grenzwert (Sollwert). Über- bzw. unterschreitet das Meßsignal diesen Wert, schaltet das zugehörige, als Grenzkontakt programmierte Relais. Hysterese: Bereich oberhalb und unterhalb des eingestellten Sollwertes, um den der Schaltpunkt des Relais verschoben wird. Dadurch wird ein Schwingen der Regelung verhindert. Hysterese: Bereich oberhalb und unterhalb des eingestellten Sollwertes, um den der Schaltpunkt des Relais verschoben wird. Dadurch wird ein Schwingen der Regelung verhindert. Verzögerungszeit Zeit, die der Wert anliegen muß, bevor es zu einer Auslösung kommt (um die das Schalten des Relais verzögert werden kann). Verzögerungszeit Zeit, die der Wert anliegen muß, bevor es zu einer Auslösung kommt (um die das Schalten des Relais verzögert werden kann). Die Eingabe dieser 3 Werte unterliegt einer Zwangsführung. Auch wenn keine Einstellung von Hysterese und Verzögerungszeit geplant ist (Werte = 0), müssen diese Untermenüs durchlaufen werden! 38 Die Eingabe dieser 3 Werte unterliegt einer Zwangsführung. Auch wenn keine Einstellung von Hysterese und Verzögerungszeit geplant ist (Werte = 0), müssen diese Untermenüs durchlaufen werden! 38 Parametrierung Oxi 170/ Oxi 296 Parametrierung Parameter für Grenzwertmelder einstellen Parameter für Grenzwertmelder einstellen Beispiel: Oberer Grenzwert für “O2“ an Relais 1einstellen. Beispiel: Oberer Grenzwert für “O2“ an Relais 1einstellen. − − Taste ENTER drücken, um in das Untermenü PL einzusteigen: − 6= 0 =50 − Mit den Tasten UP / DOWN die blinkende Stelle des Grenzwertes einstellen und mit ENTER bestätigen. − − REL1 Die erste/zweite Ziffer blinkt (je nach eingestelltem Meßbereich). O2 Mit den Tasten UP / DOWN die blinkende Stelle des Grenzwertes einstellen und mit ENTER bestätigen. Die weiteren Stellen in gleicher Weise einstellen. − Die weiteren Stellen in gleicher Weise einstellen. − Die letzte Ziffer mit ENTER bestätigen, es erscheint das Untermenü HS. − Die letzte Ziffer mit ENTER bestätigen, es erscheint das Untermenü HS. − Mit den Tasten UP / DOWN die blinkende Ziffer der Hysterese einstellen − Mit den Tasten UP / DOWN die blinkende Ziffer der Hysterese einstellen − Mit ENTER bestätigen. − Die weiteren Stellen in gleicher Weise einstellen. − Die letzte Ziffer mit ENTER bestätigen, es erscheint das Untermenü td. − Mit ENTER bestätigen. − Die weiteren Stellen in gleicher Weise einstellen. − Die letzte Ziffer mit ENTER bestätigen, es erscheint das Untermenü td. 6= 0 REL1 O2 =50 REL1 Einstellbereich: 0 bis 10 % vom Meßbereich. O2 − td 0= 20 − REL1 Taste ENTER erneut drücken, um den Grenzwert einzustellen. − REL1 O2 Taste ENTER drücken, um in das Untermenü PL einzusteigen: Taste ENTER erneut drücken, um den Grenzwert einzustellen. Die erste/zweite Ziffer blinkt (je nach eingestelltem Meßbereich). O2 Oxi 170/ Oxi 296 − Mit den Tasten UP / DOWN die Sekunden (rechte blinkende Ziffern) der Schaltverzögerung einstellen. Einstellbereich: 0 bis 10 % vom Meßbereich. O2 td 0= 20 Mit ENTER bestätigen. Die Minuten (linke zwei Stellen) in gleicher Weise einstellen. Einstellbereich: 0 bis 59 min 59 sec REL1 − Mit den Tasten UP / DOWN die Sekunden (rechte blinkende Ziffern) der Schaltverzögerung einstellen. − Mit ENTER bestätigen. − Die Minuten (linke zwei Stellen) in gleicher Weise einstellen. Einstellbereich: 0 bis 59 min 59 sec 39 39 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Parametrierung Beispiel: Rel 1: Rel 2: Beispiel: UL = 10 mg/l LL = 5 mg/l HS = 1 mg/l HS = 1 mg/l td = 0 td = 0 Rel 1: Rel 2: Meßwert UL = 10 mg/l LL = 5 mg/l td = 0 td = 0 1 Rel1 eingestellte Hysterese OG 11 mg/l UL= oberer Grenzwert 10 mg/l 10 mg/l 9 mg/l Rel1 eingestellte Hysterese OG UL= oberer Grenzwert 9 mg/l 4 2 6 mg/l HS = 1 mg/l HS = 1 mg/l Meßwert 1 11 mg/l Parametrierung Meßwert 4 2 Rel2 6 mg/l 5 mg/l LL=unterer Grenzwert 4 mg/l eingestellte Hysterese UG Meßwert Rel2 5 mg/l LL=unterer Grenzwert 4 mg/l eingestellte Hysterese UG 3 3 Zeit Zeit 1 Oberer Grenzwertmelder schaltet 2 Oberer Grenzwertmelder schaltet zurück 1 Oberer Grenzwertmelder schaltet 2 Oberer Grenzwertmelder schaltet zurück 3 Unterer Grenzwertmelder schaltet 4 Unterer Grenzwertmelder schaltet zurück 3 Unterer Grenzwertmelder schaltet 4 Unterer Grenzwertmelder schaltet zurück 40 40 Parametrierung Oxi 170/ Oxi 296 Parametrierung Eingabe der manuellen Druckkompensation Eingabe der manuellen Druckkompensation Alternativ kann der aktuelle Luftdruck (Absolutdruck!) oder die Ortshöhe (über normal Null) eingegeben werden. Bei der Luftdruckeingabe wird automatisch der Vorgabewert für die Ortshöhe angepaßt und umgekehrt. Alternativ kann der aktuelle Luftdruck (Absolutdruck!) oder die Ortshöhe (über normal Null) eingegeben werden. Bei der Luftdruckeingabe wird automatisch der Vorgabewert für die Ortshöhe angepaßt und umgekehrt. Eingabe des Luftdrucks − Eingabe des Luftdrucks Mit ENTER das Untermenü PPr aufrufen: PPr 950 − − − − − Die erste Ziffer blinkt. Mit den Tasten UP / DOWN die blinkende Stelle einstellen. Mit ENTER bestätigen. Die weiteren Stellen in gleicher Weise einstellen. Mit ENTER das Untermenü PPr aufrufen: PPr 950 − − − − Die erste Ziffer blinkt. Mit den Tasten UP / DOWN die blinkende Stelle einstellen. Mit ENTER bestätigen. Die weiteren Stellen in gleicher Weise einstellen. Einstellbereich: Einstellbereich: 500 mbar bis 1100 mbar 500 mbar bis 1100 mbar Eingabe der Ortshöhe − Oxi 170/ Oxi 296 Eingabe der Ortshöhe Mit ENTER das Untermenü PAL aufrufen: − − − − − Mit ENTER das Untermenü PAL aufrufen: − − Die erste Ziffer blinkt. Mit den Tasten UP / DOWN die blinkende Stelle einstellen. Mit ENTER bestätigen. Die weiteren Stellen in gleicher Weise einstellen. − − Die erste Ziffer blinkt. Mit den Tasten UP / DOWN die blinkende Stelle einstellen. Mit ENTER bestätigen. Die weiteren Stellen in gleicher Weise einstellen. Einstellbereich: Einstellbereich: -700 m bis 5600 m -700 m bis 5600 m 41 41 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Parametrierung Schnittstelle RS 485 (Option RS) Die Parametrierung der RS 485-Schnittstelle ist in einer separaten Anleitung beschrieben, die bei Geräten mit RS 485-Schnittstelle (Geräteausführung RS) im Lieferumfang enthalten ist. Parametrierung Schnittstelle RS 485 (Option RS) Die Parametrierung der RS 485-Schnittstelle ist in einer separaten Anleitung beschrieben, die bei Geräten mit RS 485-Schnittstelle (Geräteausführung RS) im Lieferumfang enthalten ist. Code einstellen Code einstellen Die Einstellung eines Codes verhindert, daß sich die Konfiguration und Parametrierung des Geräts durch unbeabsichtigtes oder irrtümliches Drücken einer Eingabetaste verändert. Beim Einstieg in die Konfiguration / Parametrierung muß die Codezahl vom Benutzer eingegeben werden (siehe Konfigurationsebene / Parametrierebene aufrufen). Im Auslieferungszustand ist kein Code eingestellt. Die Konfiguration und Parametrierung des Gerätes ist somit nicht geschützt. Erst die Eingabe einer Codezahl schützt das Gerät vor unbeabsichtigten oder unbefugten Veränderungen. Die Einstellung eines Codes verhindert, daß sich die Konfiguration und Parametrierung des Geräts durch unbeabsichtigtes oder irrtümliches Drücken einer Eingabetaste verändert. Beim Einstieg in die Konfiguration / Parametrierung muß die Codezahl vom Benutzer eingegeben werden (siehe Konfigurationsebene / Parametrierebene aufrufen). Im Auslieferungszustand ist kein Code eingestellt. Die Konfiguration und Parametrierung des Gerätes ist somit nicht geschützt. Erst die Eingabe einer Codezahl schützt das Gerät vor unbeabsichtigten oder unbefugten Veränderungen. Einstellung: Einstellung: − Mit ENTER das Untermenü PCd aufrufen: − − − − Mit ENTER das Untermenü PCd aufrufen: − Die aktuelle Codezahl erscheint in der Anzeige (Lieferzustand: 000). Die erste Ziffer blinkt. Die erste Ziffer mit den Tasten UP / DOWN einstellen. Mit ENTER bestätigen. − − Die aktuelle Codezahl erscheint in der Anzeige (Lieferzustand: 000). Die erste Ziffer blinkt. Die erste Ziffer mit den Tasten UP / DOWN einstellen. Mit ENTER bestätigen. Hinweis: (Die Codezahl 555 ist nicht zulässig!) Hinweis: (Die Codezahl 555 ist nicht zulässig!) − Die beiden weiteren Ziffern in gleicher − Die beiden weiteren Ziffern in gleicher Weise einstellen. Weise einstellen. Hinweis: Nach Eingabe einer Codezahl läßt sich das Gerät nur unter Verwendung dieser neuen Zahl konfigurieren oder parametrieren! Hinweis: Nach Eingabe einer Codezahl läßt sich das Gerät nur unter Verwendung dieser neuen Zahl konfigurieren oder parametrieren! Codezahl-Sperre aufheben Die Codezahl-Sperre läßt sich durch Rückstellen in den Lieferzustand wieder aufheben. Dazu als Codezahl die 000 eingeben. Codezahl-Sperre aufheben Die Codezahl-Sperre läßt sich durch Rückstellen in den Lieferzustand wieder aufheben. Dazu als Codezahl die 000 eingeben. 42 42 Parametrierung Oxi 170/ Oxi 296 Parametrierung Temperaturabgleich Oxi 170/ Oxi 296 Temperaturabgleich Das Untermenü Pt ermöglicht einen Abgleich der Temperaturmeßfühler-Toleranzen im Meßwertgeber (Verschiebung des Nullpunktes um max. 0,5 °C). Das Untermenü Pt ermöglicht einen Abgleich der Temperaturmeßfühler-Toleranzen im Meßwertgeber (Verschiebung des Nullpunktes um max. 0,5 °C). Die Meßsonde wegen der Wärmekapazität in ein Gefäß mit mindestens 2 Liter Wasser stellen. Die Meßsonde wegen der Wärmekapazität in ein Gefäß mit mindestens 2 Liter Wasser stellen. Meßsonde und Referenzthermometer mindestens 15 Minuten - bei Temperaturdifferenzen zwischen Wasser und Meßwertgeber > 10 °C mindestens 1 Stunde unter gelegentlichem Rühren im Wasser belassen, bis der Abgleich erfolgen kann. Meßsonde und Referenzthermometer mindestens 15 Minuten - bei Temperaturdifferenzen zwischen Wasser und Meßwertgeber > 10 °C mindestens 1 Stunde unter gelegentlichem Rühren im Wasser belassen, bis der Abgleich erfolgen kann. Einstellung: − Einstellung: Mit ENTER das Untermenü Pt aufrufen: − 2=4 =3 °C − Mit UP / DOWN den Wert einstellen (± 0,5 °C). Es wird gleichzeitig der korrigierte Meßwert (obere Zeile) und der Korrekturwert (untere Zeile) angezeigt. Mit ENTER das Untermenü Pt aufrufen: − 2=4 =3 − Mit ENTER bestätigen. 43 °C Mit UP / DOWN den Wert einstellen (± 0,5 °C). Es wird gleichzeitig der korrigierte Meßwert (obere Zeile) und der Korrekturwert (untere Zeile) angezeigt. − Mit ENTER bestätigen. 43 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Parametrierung Timer für externe Sensor-Reinigungseinheit (CS) Parametrierung Timer für externe Sensor-Reinigungseinheit (CS) Das Untermenü PCS erlaubt die Festlegung der Zeitintervalle für Relais, die in der Konfigurationsebene als Steuerrelais für eine externe Sensor-Reinigungseinheit (CS) konfiguriert sind. Das Untermenü PCS erlaubt die Festlegung der Zeitintervalle für Relais, die in der Konfigurationsebene als Steuerrelais für eine externe Sensor-Reinigungseinheit (CS) konfiguriert sind. Folgende Zeitintervalle können eingestellt werden: Folgende Zeitintervalle können eingestellt werden: Parameter Bereich Bedeutung Parameter Bereich Bedeutung tr 1 ... 168 h Zeitintervall zwischen zwei Reinigungsvorgängen. tr 1 ... 168 h Zeitintervall zwischen zwei Reinigungsvorgängen. tc 1 ... 300 s Dauer des Reinigungsvorgangs. Während des Reinigungsvorgangs bleibt der Meßwert eingefroren. tc 1 ... 300 s Dauer des Reinigungsvorgangs. Während des Reinigungsvorgangs bleibt der Meßwert eingefroren. th 1 ... 900 s Zeitintervall für das weitere Einfrieren des Meßwerts über das Ende des Reinigungsvorgangs hinaus. th 1 ... 900 s Zeitintervall für das weitere Einfrieren des Meßwerts über das Ende des Reinigungsvorgangs hinaus. Während tc und th ist keine Kalibrierung möglich. Sollte ein Reinigungsvorgang während einer laufenden Kalibrierung gestartet werden, wird der Start verzögert, bis die Kalibrierung beendet ist. 44 Während tc und th ist keine Kalibrierung möglich. Sollte ein Reinigungsvorgang während einer laufenden Kalibrierung gestartet werden, wird der Start verzögert, bis die Kalibrierung beendet ist. 44 Parametrierung Oxi 170/ Oxi 296 Parametrierung Zeitintervalle einstellen PCS tr 142 REL1 Zeitintervalle einstellen − Taste ENTER drücken, um in das Untermenü tr einzusteigen. − − Die erste Ziffer blinkt. Mit den Tasten UP / DOWN die blinkende Stelle einstellen. Mit ENTER bestätigen. Die weiteren Stellen in gleicher Weise einstellen. Nach dem Bestätigen der letzen Ziffer wechselt das Menü zur Eingabe der Reinigungsdauer (Anzeige tc). Die Einstellung des Werts erfolgt analog. − − − PCS tr 142 REL1 − Taste ENTER drücken, um in das Untermenü tr einzusteigen. − − Die erste Ziffer blinkt. Mit den Tasten UP / DOWN die blinkende Stelle einstellen. Mit ENTER bestätigen. Die weiteren Stellen in gleicher Weise einstellen. Nach dem Bestätigen der letzen Ziffer wechselt das Menü zur Eingabe der Reinigungsdauer (Anzeige tc). Die Einstellung des Werts erfolgt analog. − − − Zuletzt erfolgt die Einstellung der zusätzlichen Wartezeit (Anzeige th). − Oxi 170/ Oxi 296 Nach dem letzten Drücken der Taste ENTER erscheint das Ausgangsmenü der Parametrierebene (Anzeige PA). 45 Zuletzt erfolgt die Einstellung der zusätzlichen Wartezeit (Anzeige th). − Nach dem letzten Drücken der Taste ENTER erscheint das Ausgangsmenü der Parametrierebene (Anzeige PA). 45 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Betrachter-Modus Im Betrachter-Modus können ohne Codeeingabe Einstellungen abgefragt werden. Die Einstellungen können jedoch nicht verändert werden. Betrachter-Modus Im Betrachter-Modus können ohne Codeeingabe Einstellungen abgefragt werden. Die Einstellungen können jedoch nicht verändert werden. Parametrier- und Konfigurationsdaten anzeigen Parametrier- und Konfigurationsdaten anzeigen − Taste DOWN drücken. − Taste DOWN drücken. − Taste ENTER drücken, die erste Ziffer blinkt. − Taste ENTER drücken, die erste Ziffer blinkt. − Taste ESCAPE drücken. − Taste ESCAPE drücken. − Mit den Tasten UP / DOWN zwischen Parametrierung PA und Konfiguration C0 wechseln. − Mit den Tasten UP / DOWN zwischen Parametrierung PA und Konfiguration C0 wechseln. − Durch Drücken der Taste ENTER die Untermenüs durchlaufen. − Durch Drücken der Taste ENTER die Untermenüs durchlaufen. Kalibrierdaten und Softwareversion anzeigen − Im Meßmodus die Taste ENTER drücken, es erscheint die Anzeige der Sensorsteilheit: S Kalibrierdaten und Softwareversion anzeigen − Im Meßmodus die Taste ENTER drücken, es erscheint die Anzeige der Sensorsteilheit: S !07 !07 − Mit den Tasten UP / DOWN, das Untermenü So aufrufen: − Mit den Tasten UP / DOWN, das Untermenü So aufrufen: − Durch Drücken der Taste M zurück zum Meßbetrieb. − Durch Drücken der Taste M zurück zum Meßbetrieb. 46 46 Meß-Modus Oxi 170/ Oxi 296 Meß-Modus Die Geräte Oxi 170 und Oxi 296 befinden sich nach der Erst-Inbetriebnahme automatisch im Meß-Modus. Ansonsten kann der Meß-Modus - außer bei einer Zwangsführung - aus jeder Bedienebene durch Drücken der Taste M aufgerufen werden (siehe auch Abschnitt Bedienhinweise). 47 Oxi 170/ Oxi 296 Die Geräte Oxi 170 und Oxi 296 befinden sich nach der Erst-Inbetriebnahme automatisch im Meß-Modus. Ansonsten kann der Meß-Modus - außer bei einer Zwangsführung - aus jeder Bedienebene durch Drücken der Taste M aufgerufen werden (siehe auch Abschnitt Bedienhinweise). 47 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Kalibrierung Kalibrierung − Sensor aus Meßmedium entnehmen und zur Kalibrierung an Luft vorbereiten (ggf. reinigen, Temperaturanpassung abwarten). − Sensor aus Meßmedium entnehmen und zur Kalibrierung an Luft vorbereiten (ggf. reinigen, Temperaturanpassung abwarten). − Mit der Taste C in Kalibriermodus wechseln. − Mit der Taste C in Kalibriermodus wechseln. CAL CAL Hinweis: Mit der Taste ESCAPE kann die Kalibrierung abgebrochen werden. Auto Cal S CAL Auto Cal CAL =89 – S Mit ENTER Kalibrierung starten. AR blinkt. Sensorsteilheit wird ermittelt. CAL =89 Messung läuft bis zum Erreichen eines stabilen Meßwerts (AR blinkt). Auto Cal – Mit ENTER Kalibrierung starten. AR blinkt. Sensorsteilheit wird ermittelt. Messung läuft bis zum Erreichen eines stabilen Meßwerts (AR blinkt). Hinweis: Die Steilheit gibt den Zustand des Sensors wieder und wird im Bereich 0,5 bis 1,4 akzeptiert. Hinweis: Die Steilheit gibt den Zustand des Sensors wieder und wird im Bereich 0,5 bis 1,4 akzeptiert. Dauer des Kalibriervorgangs: min. 60 s bis max. 15 Minuten (falls nach max. 15 Minuten kein stabiler Meßwert erreicht ist, erscheint die Fehlermeldung “CAL ERR“ , siehe Kapitel Anzeige nach ungültiger Kalibrierung. Dauer des Kalibriervorgangs: min. 60 s bis max. 15 Minuten (falls nach max. 15 Minuten kein stabiler Meßwert erreicht ist, erscheint die Fehlermeldung “CAL ERR“ , siehe Kapitel Anzeige nach ungültiger Kalibrierung. S Stabiler Meßwert übernommen. AR erlischt. CAL =89 Auto Cal Stabiler Meßwert übernommen. AR erlischt. Auto Cal Um eine hohe Genauigkeit zu gewährleisten, empfiehlt es sich, vor der Kalibrierung den aktuellen Luftdruck (Absolutdruck!) bei PPr einzustellen. 48 Mit der Taste ESCAPE kann die Kalibrierung abgebrochen werden. Auto Cal =89 S Hinweis: Um eine hohe Genauigkeit zu gewährleisten, empfiehlt es sich, vor der Kalibrierung den aktuellen Luftdruck (Absolutdruck!) bei PPr einzustellen. 48 Kalibrierung CAL – !5 – Oxi 170/ Oxi 296 Kalibrierung Durch drücken der Taste ENTER wird Meßwert angezeigt, die Stromausgänge folgen jedoch noch nicht dem aktuellen Meßwert. Sensor kann jetzt wieder in das Meßmedium eingetaucht werden. CAL – Durch drücken der Taste ENTER wird Meßwert angezeigt, die Stromausgänge folgen jedoch noch nicht dem aktuellen Meßwert. Sensor kann jetzt wieder in das Meßmedium eingetaucht werden. – Mit Taste ENTER oder M zurück zum normalen Meßbetrieb. Recorderausgänge folgen danach wieder dem aktuellen Meßwert. !5 Mit Taste ENTER oder M zurück zum normalen Meßbetrieb. Recorderausgänge folgen danach wieder dem aktuellen Meßwert. Kalibrierfehler CAL Err Kalibrierfehler CAL Err Die Fehlermeldung CAL Err erscheint, wenn Die Fehlermeldung CAL Err erscheint, wenn • • • • kein stabiler Meßwert erreicht wurde, oder unzulässige Werte für die Steilheit gemessen wurden. − kein stabiler Meßwert erreicht wurde, oder unzulässige Werte für die Steilheit gemessen wurden. − Mit ENTER nach Behebung der Störung erneut kalibrieren. 49 Oxi 170/ Oxi 296 Mit ENTER nach Behebung der Störung erneut kalibrieren. 49 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Prüfmodus Prüfmodus aufrufen Prüfmodus Prüfmodus aufrufen − Taste ESCAPE gedrückt halten und Taste UP kurz drücken, der Prüfmodus wird aufgerufen. − Taste ESCAPE gedrückt halten und Taste UP kurz drücken, der Prüfmodus wird aufgerufen. − Durch Betätigen der Taste M oder der Taste C den Prüfmodus wieder verlassen. − Durch Betätigen der Taste M oder der Taste C den Prüfmodus wieder verlassen. Variantenerkennung Variantenerkennung Erscheint links oben im Display das O2-Symbol wurde die O2-Hardware erkannt, die Prüfung wird mit der Anzeige der Codezahl gestartet. Erscheint links oben im Display das O2-Symbol wurde die O2-Hardware erkannt, die Prüfung wird mit der Anzeige der Codezahl gestartet. Wurde die O2-Hardware nicht erkannt, erscheint folgende Fehlermeldung: Wurde die O2-Hardware nicht erkannt, erscheint folgende Fehlermeldung: Err AoPt: Hardwarefehler O2 − Setzen Sie sich mit der Technischen Err AoPt: Hardwarefehler O2 − Setzen Sie sich mit der Technischen Kundenberatung von WTW in Verbindung Codezahl anzeigen Codezahl anzeigen Im Untermenü Cod wird nach Drücken der Taste ENTER die Codezahl angezeigt: − O2 50 Kundenberatung von WTW in Verbindung ENTER erneut drücken, weiter mit Schreiberausgang 1 Im Untermenü Cod wird nach Drücken der Taste ENTER die Codezahl angezeigt: − O2 50 ENTER erneut drücken, weiter mit Schreiberausgang 1 Oxi 170/ Oxi 296 Prüfmodus Schreiberausgang 1 Schreiberausgang 1 Im Untermenü tSt rEC1 wird nach Drücken der Taste ENTER ein Strom von 0.1 mA eingestellt: O2 − M drücken, um Strom auf 0.1 mA einzustellen − C drücken, um Strom auf 10.0 mA einzust. − UP drücken, um Strom zu vergrößern (max. 20.5 mA) − Im Untermenü tSt rEC1 wird nach Drücken der Taste ENTER ein Strom von 0.1 mA eingestellt: O2 − M drücken, um Strom auf 0.1 mA einzustellen − C drücken, um Strom auf 10.0 mA einzust. − UP drücken, um Strom zu vergrößern (max. 20.5 mA) − DOWN drücken, um Strom zu verringern (min. 0.0 mA) − ENTER drücken, weiter mit Schreiberausgang DOWN drücken, um Strom zu verringern (min. 0.0 mA) − ENTER drücken, weiter mit Schreiberausgang 2 2 Schreiberausgang 2 Schreiberausgang 2 Im Untermenü tSt rEC2 wird nach Drücken der Taste ENTER ein Strom von 0.1 mA eingestellt: O2 Oxi 170/ Oxi 296 Prüfmodus − M drücken, um Strom auf 0.1 mA einzustellen − C drücken, um Strom auf 10.0 mA einzust. − UP drücken, um Strom zu vergrößern (max. 20.5 mA) − DOWN drücken, um Strom zu verringern (min. 0.0 mA) − ENTER drücken, weiter mit Relaistest. Im Untermenü tSt rEC2 wird nach Drücken der Taste ENTER ein Strom von 0.1 mA eingestellt: O2 − M drücken, um Strom auf 0.1 mA einzustellen − C drücken, um Strom auf 10.0 mA einzust. − UP drücken, um Strom zu vergrößern (max. 20.5 mA) − DOWN drücken, um Strom zu verringern (min. 0.0 mA) − ENTER drücken, weiter mit Relaistest. 51 51 Oxi 170/ Oxi 296 Relaistest Prüfmodus Relaistest Im Untermenü tSt rEL blinkt nach Drücken der Taste ENTER die Meldung tSt: O2 Oxi 170/ Oxi 296 Prüfmodus Hinweis: Rel 1 und Rel 2 werden nur angesteuert, wenn die Regeloption vorhanden ist. Im Untermenü tSt rEL blinkt nach Drücken der Taste ENTER die Meldung tSt: O2 Hinweis: Rel 1 und Rel 2 werden nur angesteuert, wenn die Regeloption vorhanden ist. Ist ein Relais eingeschaltet, wird am Display das zugehörige Symbol angesteuert. Ist ein Relais eingeschaltet, wird am Display das zugehörige Symbol angesteuert. − ESCAPE drücken: Relais 1 Ein/Aus − ESCAPE drücken: Relais 1 Ein/Aus − UP drücken: Relais 2 Ein/Aus − UP drücken: Relais 2 Ein/Aus − DOWN drücken: − DOWN drücken: Sens-Check E/A Sens-Check E/A − ENTER drücken, weiter mit RS485 RS 485 − ENTER drücken, weiter mit RS485 RS 485 Im Untermenü tSt 485 blinkt nach Drücken der Taste ENTER die Meldung tSt: Im Untermenü tSt 485 blinkt nach Drücken der Taste ENTER die Meldung tSt: Hinweis: Der Menüpunkt wird nur angeboten, wenn die Schnittstelle RS 485 vorhanden ist. Hinweis: Der Menüpunkt wird nur angeboten, wenn die Schnittstelle RS 485 vorhanden ist. O2 Die RS 485 arbeitet im Testmodus als Repeater, d. h. alle empfangenen Blöcke werden wieder zurückgesendet. Die RS 485 arbeitet im Testmodus als Repeater, d. h. alle empfangenen Blöcke werden wieder zurückgesendet. − − − − 52 O2 ESCAPE drücken: Geräteidentifikation entsprechend RS-Befehl "RSID" senden (mit RS 485-Protokoll) UP drücken: Geräteidentifikation entsprechend RS-Befehl "RSID" senden (ohne RS 485-Protokoll; für Druckerausgabe) ENTER drücken: RS 485-Test beenden, weiter bei Paßzahl anzeigen − − 52 ESCAPE drücken: Geräteidentifikation entsprechend RS-Befehl "RSID" senden (mit RS 485-Protokoll) UP drücken: Geräteidentifikation entsprechend RS-Befehl "RSID" senden (ohne RS 485-Protokoll; für Druckerausgabe) ENTER drücken: RS 485-Test beenden, weiter bei Paßzahl anzeigen Oxi 170/ Oxi 296 Prüfmodus Oxi 170/ Oxi 296 Prüfmodus Ablaufplan Ablaufplan + Variantenerkennung Messen + Variantenerkennung falsche Hardware pH-Hardware erkannt M C Messen falsche Hardware pH-Hardware erkannt M Messen / Kalibrieren C 53 Messen / Kalibrieren 53 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Reinigung / Wartung Reinigung / Wartung Reinigung / Wartung Reinigung / Wartung Die Geräte Oxi 170 und Oxi 296 sind weitgehend wartungsfrei. Hier werden einige Hinweise im Umgang mit den Geräten gegeben: Die Geräte Oxi 170 und Oxi 296 sind weitgehend wartungsfrei. Hier werden einige Hinweise im Umgang mit den Geräten gegeben: − Geräte möglichst staub- und schmutzfrei halten. − Geräte möglichst staub- und schmutzfrei halten. − Zur Reinigung des Gehäuses keinen Hochdruckreiniger verwenden. − Zur Reinigung des Gehäuses keinen Hochdruckreiniger verwenden. − Keine Reinigungsmittel verwenden, die Lösungsmittel enthalten. − Keine Reinigungsmittel verwenden, die Lösungsmittel enthalten. − Zur Reinigung und Wartung der Sensoren die Angaben gemäß SensorenBedienungsanleitungen beachten! − Zur Reinigung und Wartung der Sensoren die Angaben gemäß SensorenBedienungsanleitungen beachten! − Geräte regelmäßig auf mechanische Beschädigungen überprüfen, ggf. außer Betrieb setzen. − Geräte regelmäßig auf mechanische Beschädigungen überprüfen, ggf. außer Betrieb setzen. − Auch bei Reinigungsarbeiten die Sicherheitshinweise beachten! − Auch bei Reinigungsarbeiten die Sicherheitshinweise beachten! 54 54 Oxi 170/ Oxi 296 Störungsbehebung Oxi 170/ Oxi 296 Störungsbehebung Folgende Meldungen können auftreten (nach Vorrang geordnet): Folgende Meldungen können auftreten (nach Vorrang geordnet): Meldung Ursache Maßnahme Meldung Ursache Maßnahme Err Schwerwiegender Fehler, der kein Weitermessen gestattet − Gerät an WTW senden Err Schwerwiegender Fehler, der kein Weitermessen gestattet − Gerät an WTW senden CAL Es liegt keine gültige Kalibrierung vor − Gerät neu kalibrieren (siehe auch Kapitel Kalibrierung) CAL Es liegt keine gültige Kalibrierung vor − Gerät neu kalibrieren (siehe auch Kapitel Kalibrierung) 0FL Der O2/Temperaturwert liegt außerhalb des Meßbereiches (Overflow). − Sensor und Sensoranschluß überprüfen 0FL Der O2/Temperaturwert liegt außerhalb des Meßbereiches (Overflow). − Sensor und Sensoranschluß überprüfen Messwert blinkt Am entsprechenden Schreiberausgang liegt ein Overflow an − Schreiberbereich anpassen Messwert blinkt Am entsprechenden Schreiberausgang liegt ein Overflow an − Schreiberbereich anpassen Sensor warten (REG) − Abhilfe siehe SensorBedienungsanleitung Sensor warten (REG) − Abhilfe siehe SensorBedienungsanleitung Sensor evtl. defekt (LECK) − Abhilfe siehe SensorBedienungsanleitung Sensor evtl. defekt (LECK) − Abhilfe siehe SensorBedienungsanleitung Hardwarefehler − Gerät an WTW senden Hardwarefehler − Gerät an WTW senden Err Err AoPt Err Err AoPt 55 55 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Technische Daten Technische Daten Oxi 170 Technische Daten Technische Daten Oxi 170 222 mm 105 mm Anzeige Meßwert Einheiten, Einstellungen Meßwertauflösung Genauigkeit automatische Temperaturkompensation manuelle Luftdruckkompensation Referenztemperatur Kalibrierung Kalibrierbereich 56 222 mm 105 mm Anzeige LCD 7-Segment • O2 • Temperatur Symbole Meßwert 3½-stellig 4-stellig O2-Messung Signaleingang Anzeige- und Meßbereich 97 mm 105 mm 97 mm 105 mm 202 mm 222 mm 202 mm 222 mm Einheiten, Einstellungen LCD 7-Segment • O2 • Temperatur Symbole 3½-stellig 4-stellig O2-Messung niederohmig 0,0 bis (20) 60 mg/l; 0 bis (200) 600% abhängig vom Sensortyp 0,1 mg/l, 0,01 mg/l; 1%, 0,1% abhängig vom Sensortyp ± 1% vom Messwert ± 1 Digit NTC - 5 bis + 100°C 500 mbar bis 1100 mbar + 20°C Luftkalibrierung nach OxiCal-Verfahren Steilheit 0,5 bis 1,4 Signaleingang Anzeige- und Meßbereich Meßwertauflösung Genauigkeit automatische Temperaturkompensation manuelle Luftdruckkompensation Referenztemperatur Kalibrierung Kalibrierbereich 56 niederohmig 0,0 bis (20) 60 mg/l; 0 bis (200) 600% abhängig vom Sensortyp 0,1 mg/l, 0,01 mg/l; 1%, 0,1% abhängig vom Sensortyp ± 1% vom Messwert ± 1 Digit NTC - 5 bis + 100°C 500 mbar bis 1100 mbar + 20°C Luftkalibrierung nach OxiCal-Verfahren Steilheit 0,5 bis 1,4 Oxi 170/ Oxi 296 Technische Daten Temperaturmessung Temperatur-Sensor Genauigkeit Auflösung Oxi 170/ Oxi 296 Technische Daten Temperaturmessung NTC integriert im Sensor ± 0,2 K ± 1 digit zusätzliche Feinjustierung um ± 0,5 K 0,1 K Temperatur-Sensor Genauigkeit Auflösung Ein- / Ausgänge NTC integriert im Sensor ± 0,2 K ± 1 digit zusätzliche Feinjustierung um ± 0,5 K 0,1 K Ein- / Ausgänge Sensoreingang Kontaktausgänge 7-poliger Rundsteckverbinder mit Schraubfixierung SENS-CHECK-Relais schließt bei Sensordefekt Relais 1/ Relais 2 Funktionen, Grenzwert • max.Schaltspannung 250 VAC • max.Schaltstrom 5A • max. Schaltleistung 150 W (ohmsche Last) Sensoreingang Kontaktausgänge 7-poliger Rundsteckverbinder mit Schraubfixierung SENS-CHECK-Relais schließt bei Sensordefekt Relais 1/ Relais 2 Funktionen, Grenzwert • max.Schaltspannung 250 VAC • max.Schaltstrom 5A • max. Schaltleistung 150 W (ohmsche Last) Signalausgänge 0/4 bis 20mA; galvanisch getrennt; Schreiberbereiche und Schreiberdämpfung über Software einstellbar • Grundgenauigkeit 0.1% • Bürde max. 600 Ohm • Bürdeneinfluß < 0.1 % Signalausgänge 0/4 bis 20mA; galvanisch getrennt; Schreiberbereiche und Schreiberdämpfung über Software einstellbar • Grundgenauigkeit 0.1% • Bürde max. 600 Ohm • Bürdeneinfluß < 0.1 % Anschlußklemmen zugänglich nach Öffnen des Gerätes; Kabeleinführung durch 4 PG-Verschraubungen Anschlußquerschnitt 0.5 bis 2.5 mm² • Netz 2 polig • Relais 1/2 je 2 polig • SENS Check 2 polig • Schreiberanschlüsse je 2 polig • Sensor 7 polig Anschlußklemmen zugänglich nach Öffnen des Gerätes; Kabeleinführung durch 4 PG-Verschraubungen Anschlußquerschnitt 0.5 bis 2.5 mm² • Netz 2 polig • Relais 1/2 je 2 polig • SENS Check 2 polig • Schreiberanschlüsse je 2 polig • Sensor 7 polig Schutzart Schutzart Blitzschutz (Ein- und Ausgänge) • Grobschutz • Feinschutz Elektrischer Geräteschutz Gehäuse Schutzklasse 2 nach IEC 1010 IP 66 90 V / 1.5 KA (8/20µs) 600 Watt 57 Blitzschutz (Ein- und Ausgänge) • Grobschutz • Feinschutz Elektrischer Geräteschutz Gehäuse Schutzklasse 2 nach IEC 1010 IP 66 90 V / 1.5 KA (8/20µs) 600 Watt 57 Oxi 170/ Oxi 296 Elektrische Anschlußdaten Spannungsversorgung (je nach Geräteausführung) Frequenz Leistungsaufnahme Prüfzeichen Funkentstörung Störfestigkeit Umgebungstemperatur Grenzbetriebsbereich Lagerung- und Transporttemperatur Klimaklasse Mechanische Daten Abmessungen Gewicht Tastaturfolie (Material) Gehäuse (Material) 58 Oxi 170/ Oxi 296 Technische Daten Technische Daten Elektrische Anschlußdaten • 230 VAC (– 15% + 10%) • 115 VAC (– 15% + 10%) • 24 VAC (– 15% + 10%) • 24 VDC (– 30% + 20%) 48 bis 62 Hz max. 18 Watt UL, cUL (für 115 VAC, 24 VAC und 24 VDC) für CE alle (für Versorgungsspannungen) alle Versorgungsspannungen) nach EN 50081-1 nach EN 50082-2, Namurempfehlungen – 25 °C bis + 55 °C – 25 °C bis + 65 °C Klimaklasse 4, VDI / VDE 3540 Bl.2 222 x 238 (202) x 105 mm (B x H x T) (Höhe in Klammern ohne PG-Verschraubungen) ca. 2,2 kg Polyester Polycarbonat Spannungsversorgung (je nach Geräteausführung) Frequenz Leistungsaufnahme Prüfzeichen Funkentstörung Störfestigkeit Umgebungstemperatur Grenzbetriebsbereich Lagerung- und Transporttemperatur Klimaklasse Mechanische Daten Abmessungen Gewicht Tastaturfolie (Material) Gehäuse (Material) 58 • 230 VAC (– 15% + 10%) • 115 VAC (– 15% + 10%) • 24 VAC (– 15% + 10%) • 24 VDC (– 30% + 20%) 48 bis 62 Hz max. 18 Watt UL, cUL (für 115 VAC, 24 VAC und 24 VDC) GS, CE (für alle Versorgungsspannungen) nach EN 50081-1 nach EN 50082-2, Namurempfehlungen – 25 °C bis + 55 °C – 25 °C bis + 65 °C Klimaklasse 4, VDI / VDE 3540 Bl.2 222 x 238 (202) x 105 mm (B x H x T) (Höhe in Klammern ohne PG-Verschraubungen) ca. 2,2 kg Polyester Polycarbonat Oxi 170/ Oxi 296 Technische Daten Technische Daten Oxi 296 Technische Daten Oxi 296 Anzeige Meßwert Einheiten, Einstellungen Anzeige LCD 7-Segment • O2 • Temperatur Symbole Meßwert 3½-stellig 4-stellig Einheiten, Einstellungen O2-Messung Signaleingang Anzeige- und Meßbereich Meßwertauflösung Genauigkeit automatische Temperaturkompensation manuelle Luftdruckkompensation Referenztemperatur Kalibrierung Kalibrierbereich Oxi 170/ Oxi 296 Technische Daten LCD 7-Segment • O2 • Temperatur Symbole 3½-stellig 4-stellig O2-Messung niederohmig 0,0 bis (20) 60 mg/l; 0 bis (200) 600% abhängig vom Sensortyp 0,1 mg/l, 0,01 mg/l; 1%, 0,1% abhängig vom Sensortyp ± 1% vom Messwert ± 1 Digit NTC - 5 bis + 100°C • Luftdruck: 500 mbar bis 1100 mbar • Ortshöhe: - 698 m bis 5573 m + 20°C Luftkalibrierung nach OxiCal-Verfahren Steilheit 0,5 bis 1,4 59 Signaleingang Anzeige- und Meßbereich Meßwertauflösung Genauigkeit automatische Temperaturkompensation manuelle Luftdruckkompensation Referenztemperatur Kalibrierung Kalibrierbereich niederohmig 0,0 bis (20) 60 mg/l; 0 bis (200) 600% abhängig vom Sensortyp 0,1 mg/l, 0,01 mg/l; 1%, 0,1% abhängig vom Sensortyp ± 1% vom Messwert ± 1 Digit NTC - 5 bis + 100°C • Luftdruck: 500 mbar bis 1100 mbar • Ortshöhe: - 698 m bis 5573 m + 20°C Luftkalibrierung nach OxiCal-Verfahren Steilheit 0,5 bis 1,4 59 Oxi 170/ Oxi 296 Temperaturmessung Temperatur-Sensor Genauigkeit Auflösung Oxi 170/ Oxi 296 Technische Daten Technische Daten Temperaturmessung NTC integriert im Sensor ± 0,2 K ± 1 digit zusätzliche Feinjustierung um ± 0,5 K 0,1 K Ein- / Ausgänge Temperatur-Sensor Genauigkeit Auflösung NTC integriert im Sensor ± 0,2 K ± 1 digit zusätzliche Feinjustierung um ± 0,5 K 0,1 K Ein- / Ausgänge digitale Schnittstelle RS-485; 2(3)-Draht-Verbindung Busbetrieb mit bis zu 31 Einheiten möglich digitale Schnittstelle RS-485; 2(3)-Draht-Verbindung Busbetrieb mit bis zu 31 Einheiten möglich Kontaktausgänge SENS-CHECK-Relais Relais 1/ Relais 2 • max.Schaltspannung • max.Schaltstrom • max. Schaltleistung Kontaktausgänge SENS-CHECK-Relais Relais 1/ Relais 2 • max.Schaltspannung • max.Schaltstrom • max. Schaltleistung Signalausgänge 0/4 bis 20mA; galvanisch getrennt; Schreiberbereiche und Schreiberdämpfung über Software einstellbar • Grundgenauigkeit 0.1% • Bürde max. 600 Ohm • Bürdeneinfluß < 0.1 % Signalausgänge 0/4 bis 20mA; galvanisch getrennt; Schreiberbereiche und Schreiberdämpfung über Software einstellbar • Grundgenauigkeit 0.1% • Bürde max. 600 Ohm • Bürdeneinfluß < 0.1 % Anschlußklemmen zugänglich an der Geräterückwand Anschlußquerschnitt 0.5 bis 2.5 mm² • Netz 2 polig • Relais 1/2 je 2 polig • SENS Check 2 polig • RS-485 3 polig • Schreiberanschlüsse je 2 polig • Sensor 7 polig Anschlußklemmen zugänglich an der Geräterückwand Anschlußquerschnitt 0.5 bis 2.5 mm² • Netz 2 polig • Relais 1/2 je 2 polig • SENS Check 2 polig • RS-485 3 polig • Schreiberanschlüsse je 2 polig • Sensor 7 polig 60 schließt bei Sensordefekt Funktionen, Grenzwert 250 VAC 5A 150 W (ohmsche Last) 60 schließt bei Sensordefekt Funktionen, Grenzwert 250 VAC 5A 150 W (ohmsche Last) Oxi 170/ Oxi 296 Technische Daten Schutzart Schutzart Blitzschutz (Ein- und Ausgänge) • Grobschutz • Feinschutz Elektrischer Geräteschutz Gehäuse Schutzklasse 2 nach IEC 1010 IP 54 90 V / 1.5 KA (8/20µs) 600 Watt Elektrische Anschlußdaten Spannungsversorgung (je nach Geräteausführung) Frequenz Leistungsaufnahme Prüfzeichen Funkentstörung Störfestigkeit • 230 VAC (– 15% + 10%) • 115 VAC (– 15% + 10%) • 24 VAC (– 15% + 10%) • 24 VDC (– 30% + 20%) 48 bis 62 Hz max. 18 Watt UL, cUL (für 115 VAC, 24 VAC und 24 VDC) CE (für alle Versorgungsspannungen) nach EN 50081-1 nach EN 50082-2, Namurempfehlungen • Grobschutz • Feinschutz Elektrischer Geräteschutz Gehäuse Schutzklasse 2 nach IEC 1010 IP 54 Spannungsversorgung (je nach Geräteausführung) Frequenz Leistungsaufnahme Prüfzeichen Funkentstörung Störfestigkeit 90 V / 1.5 KA (8/20µs) 600 Watt • 230 VAC (– 15% + 10%) • 115 VAC (– 15% + 10%) • 24 VAC (– 15% + 10%) • 24 VDC (– 30% + 20%) 48 bis 62 Hz max. 18 Watt UL, cUL (für 115 VAC, 24 VAC und 24 VDC) GS, CE (für alle Versorgungsspannungen) nach EN 50081-1 nach EN 50082-2, Namurempfehlungen Umgebungstemperatur – 25 °C bis + 55 °C – 25 °C bis + 65 °C Grenzbetriebsbereich Lagerung- und Transporttemperatur Mechanische Daten Abmessungen Gewicht Tastaturfolie (Material) Gehäuse (Material) Blitzschutz (Ein- und Ausgänge) Elektrische Anschlußdaten Umgebungstemperatur Grenzbetriebsbereich Lagerung- und Transporttemperatur Oxi 170/ Oxi 296 Technische Daten – 25 °C bis + 55 °C – 25 °C bis + 65 °C Mechanische Daten 96 x 96 x 168 mm (B x H x T) ca. 1,1 kg Polyester glasfaserverstärktes Noryl Abmessungen Gewicht Tastaturfolie (Material) Gehäuse (Material) 61 96 x 96 x 168 mm (B x H x T) ca. 1,1 kg Polyester glasfaserverstärktes Noryl 61 Operating Manual ba24105e06 11/2004 Operating Manual Oxi Monitors Oxi Monitors Oxi 170 Oxi 296 Oxi 170 Oxi 296 Oxi 170 Oxi 170 Oxi 296 Oxi 296 ba24105e04 07/01 General informations Accuracy when going to press The use of advanced technology and the high quality standard of our instruments are the result of continuous development. This may result in differences between this operating manual and your meter. We cannot guarantee that there are absolutely no errors in this manual. We are sure you will understand that we cannot accept any legal claims resulting from the data, figures or descriprtions. The informaiton in this manual is subject to change without any notice. Warranty General informations Accuracy when going to press The use of advanced technology and the high quality standard of our instruments are the result of continuous development. This may result in differences between this operating manual and your meter. We cannot guarantee that there are absolutely no errors in this manual. We are sure you will understand that we cannot accept any legal claims resulting from the data, figures or descriprtions. The informaiton in this manual is subject to change without any notice. Warranty The designated meter is covered by a warranty of 2 years from the date of purchase. The designated meter is covered by a warranty of 2 years from the date of purchase. The meter warranty extends to manufacturing faults that are determined within the period of warranty. The meter warranty extends to manufacturing faults that are determined within the period of warranty. The warranty claim extends to restoring the meter to readiness for use but not, however, to any further claim for damages. Improper handling or unauthorized opening of the meter invalidates any warranty claim. The warranty claim extends to restoring the meter to readiness for use but not, however, to any further claim for damages. Improper handling or unauthorized opening of the meter invalidates any warranty claim. To ascertain the warranty liability, return the meter and proof of purchase together with the date of purchase freight paid or prepaid. To ascertain the warranty liability, return the meter and proof of purchase together with the date of purchase freight paid or prepaid. Copyright Weilheim 1999, WTW GmbH & Co. KG Reprinting - even in the form of excerpts - is only allowed with the explicit written authorization of WTW GmbH & Co. KG, Weilheim. Printed in Germany. Copyright Weilheim 1999, WTW GmbH & Co. KG Reprinting - even in the form of excerpts - is only allowed with the explicit written authorization of WTW GmbH & Co. KG, Weilheim. Printed in Germany. Safety Instructions Oxi 170/ Oxi 296 Safety Instructions Please read these safety instructions carefully before installing the instrument! Oxi 170/ Oxi 296 Please read these safety instructions carefully before installing the instrument! This instrument is built according to the safety rules for electronic measuring instruments and left the factory in a safe and secure condition from a safety engineering aspect (IEC 1010). This instrument is built according to the safety rules for electronic measuring instruments and left the factory in a safe and secure condition from a safety engineering aspect (IEC 1010). The smooth functioning and operational safety of the equipment can only be guaranteed by following the general safety precautions applicable and the special safety instructions given in this operating manual. The smooth functioning and operational safety of the equipment can only be guaranteed by following the general safety precautions applicable and the special safety instructions given in this operating manual. – Before switching on the instrument, ensure that the operational voltage specified for the instrument corresponds to the power supply. (specification of the ranges of the voltage supply). – Before switching on the instrument, ensure that the operational voltage specified for the instrument corresponds to the power supply. (specification of the ranges of the voltage supply). – This instrument may only be operated using accessories that comply with the specifications in the chapter "Technical Data" of this operating manual. The manufacturer accepts no liability for damage resulting from the use of unsuitable accessories. – This instrument may only be operated using accessories that comply with the specifications in the chapter "Technical Data" of this operating manual. The manufacturer accepts no liability for damage resulting from the use of unsuitable accessories. – The trouble-free function and operational safety of the instrument can only be guaranteed by following the climate conditions specified in the chapter "Technical data" of this operating manual. – The trouble-free function and operational safety of the instrument can only be guaranteed by following the climate conditions specified in the chapter "Technical data" of this operating manual. – Opening the instrument as well as adjustment and maintenance or repair work must only be performed by personnel authorized by WTW. Depending on the severity, contravention can lead to loss of warranty. – Opening the instrument as well as adjustment and maintenance or repair work must only be performed by personnel authorized by WTW. Depending on the severity, contravention can lead to loss of warranty. – If safe operation is no longer possible, the equipment must be taken out of service and secured against inadvertent operation by labeling with warning signs. – If safe operation is no longer possible, the equipment must be taken out of service and secured against inadvertent operation by labeling with warning signs. – The safety of the user can be affected by the instrument if, for example, ! the instrument is visibly damaged, ! the instrument no longer operates as prescribed, ! the instrument has been stored under adverse conditions for a lengthy period of time, ! the instrument was exposed to adverse transport conditions. – The safety of the user can be affected by the instrument if, for example, ! the instrument is visibly damaged, ! the instrument no longer operates as prescribed, ! the instrument has been stored under adverse conditions for a lengthy period of time, ! the instrument was exposed to adverse transport conditions. – Basically, if you are in any doubt, please return the instrument for repair or maintenance to the manufacturer of the equipment, "Wissenschaftlich-Technische-Werkstätten GmbH". – Basically, if you are in any doubt, please return the instrument for repair or maintenance to the manufacturer of the equipment, "Wissenschaftlich-Technische-Werkstätten GmbH". 69 69 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Contents Contents Safety Instructions ..................................................................................................69 Safety Instructions ..................................................................................................69 Description...............................................................................................................72 Front views ..........................................................................................................72 Control panel .......................................................................................................73 Display ...........................................................................................................73 Display messages ..........................................................................................74 Keyboard........................................................................................................76 Operating instructions ....................................................................................76 Operating levels...................................................................................................77 Description...............................................................................................................72 Front views ..........................................................................................................72 Control panel .......................................................................................................73 Display ...........................................................................................................73 Display messages ..........................................................................................74 Keyboard........................................................................................................76 Operating instructions ....................................................................................76 Operating levels...................................................................................................77 Installation ...............................................................................................................79 General instructions.............................................................................................79 Power supply .......................................................................................................79 “SENS-CHECK“ connection.................................................................................80 REC 1 / REC 2 connections.................................................................................80 K1 / K2 (relay contacts) .......................................................................................80 RS 485 digital interface (RS option).......................................................................81 Installation instructions for the Oxi 170................................................................82 Terminal assignment......................................................................................82 Connecting TriOxmatic® 690 or TriOxmatic® 70x sensors.............................83 Installation instructions for the Oxi 296................................................................86 Terminal assignment......................................................................................86 Connecting TriOxmatic® 690 or TriOxmatic® 70x ..........................................87 Installation ...............................................................................................................79 General instructions.............................................................................................79 Power supply .......................................................................................................79 “SENS-CHECK“ connection.................................................................................80 REC 1 / REC 2 connections.................................................................................80 K1 / K2 (relay contacts) .......................................................................................80 RS 485 digital interface (RS option).......................................................................81 Installation instructions for the Oxi 170................................................................82 Terminal assignment......................................................................................82 Connecting TriOxmatic® 690 or TriOxmatic® 70x sensors.............................83 Installation instructions for the Oxi 296................................................................86 Terminal assignment......................................................................................86 Connecting TriOxmatic® 690 or TriOxmatic® 70x ..........................................87 Configuration ...........................................................................................................90 Factory settings ...................................................................................................90 Calling up the configuration level.........................................................................91 Overview table of the submenus....................................................................91 Salinity correction ................................................................................................93 Selecting the sensor ............................................................................................94 Selecting the measuring range ............................................................................95 Selecting the REC 1 recorder output ...................................................................96 Selecting the REC 2 recorder output (only in T-Option) .........................................97 Relay 1 / Relay 2 (R option).................................................................................98 Selecting the relay functions ..........................................................................98 Regulating signals ...............................................................................................99 Limit indicator (UL.LL) ....................................................................................99 Select the switching direction (opener / closer) for FrC, UL.LL......................99 Configuration ...........................................................................................................90 Factory settings ...................................................................................................90 Calling up the configuration level.........................................................................91 Overview table of the submenus....................................................................91 Salinity correction ................................................................................................93 Selecting the sensor ............................................................................................94 Selecting the measuring range ............................................................................95 Selecting the REC 1 recorder output ...................................................................96 Selecting the REC 2 recorder output (only in T-Option) .........................................97 Relay 1 / Relay 2 (R option).................................................................................98 Selecting the relay functions ..........................................................................98 Regulating signals ...............................................................................................99 Limit indicator (UL.LL) ....................................................................................99 Select the switching direction (opener / closer) for FrC, UL.LL......................99 70 70 Contents Oxi 170/ Oxi 296 Contents Oxi 170/ Oxi 296 Parameterization....................................................................................................100 Factory settings .................................................................................................100 Calling up the parameterization level.................................................................101 Overview table of the submenus ..................................................................102 Parameterization of salinity (only if CSA 0n) .......................................................102 REC 1 and REC 2 recorder outputs...................................................................103 Relay 1 / Relay 2 (instrument version R) ...............................................................104 Limit indicator (UL.LL)........................................................................................105 Setting the parameters for limit indicators ....................................................105 Entering the manual pressure compensation ....................................................107 Entering the air pressure ..............................................................................107 Entering the elevation ..................................................................................107 RS 485 interface (Option RS) ..............................................................................108 Setting up the code ............................................................................................108 Temperature compensation ...............................................................................109 Timer for an external probe cleaning unit (CS) ..................................................110 Setting the intervals......................................................................................111 Parameterization....................................................................................................100 Factory settings .................................................................................................100 Calling up the parameterization level.................................................................101 Overview table of the submenus ..................................................................102 Parameterization of salinity (only if CSA 0n) .......................................................102 REC 1 and REC 2 recorder outputs...................................................................103 Relay 1 / Relay 2 (instrument version R) ...............................................................104 Limit indicator (UL.LL)........................................................................................105 Setting the parameters for limit indicators ....................................................105 Entering the manual pressure compensation ....................................................107 Entering the air pressure ..............................................................................107 Entering the elevation ..................................................................................107 RS 485 interface (Option RS) ..............................................................................108 Setting up the code ............................................................................................108 Temperature compensation ...............................................................................109 Timer for an external probe cleaning unit (CS) ..................................................110 Setting the intervals......................................................................................111 Viewing Mode.........................................................................................................112 Displaying the parameterization and configuration data ..............................112 Displaying the calibration data and software version ...................................112 Viewing Mode.........................................................................................................112 Displaying the parameterization and configuration data ..............................112 Displaying the calibration data and software version ...................................112 Measuring Mode ....................................................................................................113 Measuring Mode ....................................................................................................113 Calibration..............................................................................................................114 Calibration error, CAL Err ...................................................................................115 Calibration..............................................................................................................114 Calibration error, CAL Err ...................................................................................115 Checking Mode ......................................................................................................116 Calling up the checking mode............................................................................116 Variant identification ..........................................................................................116 Displaying the code number ..............................................................................116 Recorder output 1 ..............................................................................................117 Recorder output 2 ..............................................................................................117 Relay test ...........................................................................................................118 RS 485 ...............................................................................................................118 Flowchart ...........................................................................................................119 Checking Mode ......................................................................................................116 Calling up the checking mode............................................................................116 Variant identification ..........................................................................................116 Displaying the code number ..............................................................................116 Recorder output 1 ..............................................................................................117 Recorder output 2 ..............................................................................................117 Relay test ...........................................................................................................118 RS 485 ...............................................................................................................118 Flowchart ...........................................................................................................119 Cleaning / Maintenance.........................................................................................120 Cleaning / Maintenance.........................................................................................120 Troubleshooting ....................................................................................................121 Troubleshooting ....................................................................................................121 Technical data........................................................................................................122 Technical data for Oxi 170 .................................................................................122 Technical data for Oxi 296 .................................................................................125 Technical data........................................................................................................122 Technical data for Oxi 170 .................................................................................122 Technical data for Oxi 296 .................................................................................125 Appendix: Folded pages Configuration and Parameterization Appendix: Folded pages Configuration and Parameterization 71 71 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Description Front views Front views Oxi 170 Oxi 170 Oxi 170 Oxi 296 Oxi 170 Oxi 296 Oxi 296 72 Description Oxi 296 72 Description Oxi 170/ Oxi 296 Description Control panel Control panel Display Display Oxygen measuring mode Oxygen measuring mode Slope of sensor Slope of sensor Alphanumeric display: measured value, slope, user interface Alphanumeric display: measured value, slope, user interface Dimensions: % Dimensions: % Dimensions: mg/l Dimensions: mg/l Alarm display if sensor is defective Alarm display if sensor is defective Input of salinity correction Input of salinity correction Dimension: °C Dimension: °C Relay 2 is active Relay 2 is active Calibration: AutoRead “Active “ Calibration: AutoRead “Active “ Relay 1 is active Relay 1 is active Automatic calibration OxiCal® Alphanumeric display: Oxi 170/ Oxi 296 Automatic calibration OxiCal® temperature, configuration parameters Alphanumeric display: IDENT no./RS 485 operation IDENT no./RS 485 operation BAUD rate/RS 485 interface BAUD rate/RS 485 interface Salinity correction is active Salinity correction is active 73 temperature, configuration parameters 73 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Description Display messages Note: The first letter of a display message is used for designation. Configuration displays have a “C” as the first letter and a "P" identifies displays of the parameterization. Display messages Note: The first letter of a display message is used for designation. Configuration displays have a “C” as the first letter and a "P" identifies displays of the parameterization. Configuration: Configuration: C0 COnfiguration C0 COnfiguration CSA Configuration SAlinity CSA Configuration SAlinity CIn Configuration Input CIn Configuration Input Crn Configuration Range Crn Configuration Range Cr1 Configuration recorder 1 Cr1 Configuration recorder 1 Cr2 Configuration recorder 2 Cr2 Configuration recorder 2 Configuration relay configuration CrF Configuration relay Function Configuration relay configuration CrF Configuration relay Function Parameterization: Parameterization: PA PArameterization PA PArameterization PSA Parameterization SAlinity PSA Parameterization SAlinity Pr1 Parameterization recorder 1 Pr1 Parameterization recorder 1 Pr2 Parameterization recorder 2 Pr2 Parameterization recorder 2 PL Parameterization Limits PL Parameterization Limits PPr Parameterization Pressure PPr Parameterization Pressure PAL Parameterization ALtitude PAL Parameterization ALtitude PIF Parameterization InterFace PIF Parameterization InterFace PCd Parameterization Code PCd Parameterization Code Pt Parameterization temperature Pt Parameterization temperature PCS Parameterization Cleaning System PCS Parameterization Cleaning System 74 Description 74 Description Oxi 170/ Oxi 296 Description General: LL Oxi 170/ Oxi 296 General: LL Lower Limit Upper Limit Lower Limit Upper Limit HS HySteresis HS HySteresis td time delay td time delay Viewing mode: Viewing mode: Software version Software version 75 75 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Description Keyboard • Keyboard Operating keys to switch between Measurement (M) and Calibration (C) • Description Function keys to switch between the operating levels and changing of setting values in configuration and parameterization. • Operating keys to switch between Measurement (M) and Calibration (C) • Function keys to switch between the operating levels and changing of setting values in configuration and parameterization. ESCAPE zum Verlassen eines Menüs UP Wert höher oder im Rollmodus nach oben ESCAPE zum Verlassen eines Menüs UP Wert höher oder im Rollmodus nach oben DOWN Wert kleiner oder im Rollmodus nach unten ENTER Eingaben bestätigen DOWN Wert kleiner oder im Rollmodus nach unten ENTER Eingaben bestätigen Operating instructions Operating instructions The user interface is partly implemented using "compelled guidance", i.e. all directly dependent menus must be passed through. A Code enables access to the submenus, PA (Parameterization) and C0 (Configuration) (see section "Configuration" and "Parameterization"). Select between C0 and PA using the keys: or Change to the next submenu: Select the required setting: The user interface is partly implemented using "compelled guidance", i.e. all directly dependent menus must be passed through. A Code enables access to the submenus, PA (Parameterization) and C0 (Configuration) (see section "Configuration" and "Parameterization"). Select between C0 and PA using the keys: Change to the next submenu: or Select the required setting: Accept the setting: Accept the setting: Return to the program start: (except under compelled guidance) Return to the program start: (except under compelled guidance) or to the last submenu: or to the last submenu: Return to the "Measure/Calibrate" function - if no compelled guidance is present: Return to the "Measure/Calibrate" function - if no compelled guidance is present: 76 or 76 or Description Oxi 170/ Oxi 296 Description Operating levels Oxi 170/ Oxi 296 Operating levels The instrument functions are incorporated in three levels that are consecutively structured to ensure a clear and transparent structure. This structure ensures that the user is provided with an instrument that, although it has universal options, can still be set so that unauthorized actions do not interfere with the reliable measuring mode. The instrument functions are incorporated in three levels that are consecutively structured to ensure a clear and transparent structure. This structure ensures that the user is provided with an instrument that, although it has universal options, can still be set so that unauthorized actions do not interfere with the reliable measuring mode. Operating level: The configuration and parameterization can be interrogated in the operating level without having to enter a code while the measuring mode continues to run. However, the settings cannot be changed. The Measure and Calibrate operating modes can be selected without any access restrictions. Operating level: The configuration and parameterization can be interrogated in the operating level without having to enter a code while the measuring mode continues to run. However, the settings cannot be changed. The Measure and Calibrate operating modes can be selected without any access restrictions. Parameterization level: The measuring ranges, limiting values, etc. are entered here. Access is protected by a code. Parameterization level: The measuring ranges, limiting values, etc. are entered here. Access is protected by a code. Configuration level: The functions of the monitor are allocated in this level. The configuration is performed after the installation of the instrument, mainly on the initial commissioning. Access is also protected by a code. Configuration level: The functions of the monitor are allocated in this level. The configuration is performed after the installation of the instrument, mainly on the initial commissioning. Access is also protected by a code. 77 77 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Description Description Note: After a power fail, the instrument returns to the previous operating mode. All settings are preserved. Note: After a power fail, the instrument returns to the previous operating mode. All settings are preserved. 78 78 Installation Oxi 170/ Oxi 296 Installation General instructions • • • • Oxi 170/ Oxi 296 General instructions Instruments to be installed in the field (Oxi 170) must be equipped with a protective cover (see WTW accessories). After installing the Oxi 170, close the cover to ensure compliance with the IP66 standard. Inputs/outputs require no additional lightning protection. The measures required for lightning protection are already incorporated in the monitor and any existing lightning protection measures can be used in addition. The PG screws of the Oxi 170 are designed for cable diameters of 10 to 14 mm. Unused cable feed-throughs (PG screws) are equipped with a sealing plug to ensure compliance with the IP66 standard. Power supply • • • • Instruments to be installed in the field (Oxi 170) must be equipped with a protective cover (see WTW accessories). After installing the Oxi 170, close the cover to ensure compliance with the IP66 standard. Inputs/outputs require no additional lightning protection. The measures required for lightning protection are already incorporated in the monitor and any existing lightning protection measures can be used in addition. The PG screws of the Oxi 170 are designed for cable diameters of 10 to 14 mm. Unused cable feed-throughs (PG screws) are equipped with a sealing plug to ensure compliance with the IP66 standard. Power supply Only allow qualified electricians to perform the installation as it involves a line voltage that could endanger life. A bipolar disconnection option between instrument and mains is provided (e.g. a fuse)! Only allow qualified electricians to perform the installation as it involves a line voltage that could endanger life. A bipolar disconnection option between instrument and mains is provided (e.g. a fuse)! The instruments are designed for 230 VAC, 115 VAC, 24 VAC or 24 VDC. The line voltage is printed on the nameplate. Always check that the correct line voltage is applied before commissioning the instrument. An incorrect line voltage can result in damage to the instrument! The instruments are designed for 230 VAC, 115 VAC, 24 VAC or 24 VDC. The line voltage is printed on the nameplate. Always check that the correct line voltage is applied before commissioning the instrument. An incorrect line voltage can result in damage to the instrument! In instruments with a 24 V DC module, observe the following: Only operate instruments with a voltage source that fulfills the requirements for SELV (Safety Extra Low Voltage with enhanced insulation against dangerous voltages) in accordance with EN 60950. Without an interface, the requirements should fulfill EN 61010-1. In instruments with a 24 V DC module, observe the following: Only operate instruments with a voltage source that fulfills the requirements for SELV (Safety Extra Low Voltage with enhanced insulation against dangerous voltages) in accordance with EN 60950. Without an interface, the requirements should fulfill EN 61010-1. All instruments of the "170/296" series are constructed in accordance with safety class II, i.e. no protective earth conductor is required. All instruments of the "170/296" series are constructed in accordance with safety class II, i.e. no protective earth conductor is required. Do not connect the protective earth conductor to a terminal potential or supply line or feed it into the instrument! Only authorized WTW technicians are allowed to change the instrument fuse. Do not connect the protective earth conductor to a terminal potential or supply line or feed it into the instrument! Only authorized WTW technicians are allowed to change the instrument fuse. 79 79 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Installation "SENS-CHECK" connection Installation "SENS-CHECK" connection The "SENS-CHECK" relay is designed as a closing contact that is electrically isolated from the instrument; it is then always active (= closed) if a sensor error occurs. This message is also output on the display. Sensor errors in the switching station are displayed using the relay. The "SENS-CHECK" relay is designed as a closing contact that is electrically isolated from the instrument; it is then always active (= closed) if a sensor error occurs. This message is also output on the display. Sensor errors in the switching station are displayed using the relay. Note: The relay contact should only be loaded with a maximum of 230 V AC / 5A up to a maximum of 150 W. Note: The relay contact should only be loaded with a maximum of 230 V AC / 5A up to a maximum of 150 W. REC 1 / REC 2 connections REC 1 / REC 2 connections The REC 1 (O2) and REC 2 (temperature) current outputs can be configured as follows: The REC 1 (O2) and REC 2 (temperature) current outputs can be configured as follows: • • • • 0 to 20 mA 4 to 20 mA If terminals with a common earth are used, ensure the exact polarity of the direction of the current flow (+ / – ). It involves active current sources that require no external current source! 0 to 20 mA 4 to 20 mA If terminals with a common earth are used, ensure the exact polarity of the direction of the current flow (+ / – ). It involves active current sources that require no external current source! Do not use an external current source as this can lead to malfunction of the current outputs! Maximum load of 600 Ohm. K1 / K2 (relay contacts) Do not use an external current source as this can lead to malfunction of the current outputs! Maximum load of 600 Ohm. K1 / K2 (relay contacts) The K1 and K2 relay contacts are designed as potential-free closers (make contacts). These contacts can also be configured as openers (break contacts) via the configuration level. The assignment of the relay to the corresponding functions is undertaken by the software configuration. The K1 and K2 relay contacts are designed as potential-free closers (make contacts). These contacts can also be configured as openers (break contacts) via the configuration level. The assignment of the relay to the corresponding functions is undertaken by the software configuration. Note: The contacts are designed for 230 V AC / 5A with, however, a maximum of 150 W. Note: The contacts are designed for 230 V AC / 5A with, however, a maximum of 150 W. 80 80 Installation Oxi 170/ Oxi 296 Installation RS 485 digital interface (RS option) Oxi 170/ Oxi 296 RS 485 digital interface (RS option) The RS 485 interface operates with differential levels that are not susceptible to interference. In this way, cable lengths of up to 1 km long can be implemented. The instruments are connected via a 2-wire line. A twisted 3-wire line is recommended for greater lengths or a larger number of instruments; the third line is used as a reference potential (GND) to compensate for any possible differences in potential that occur. The RS 485 interface operates with differential levels that are not susceptible to interference. In this way, cable lengths of up to 1 km long can be implemented. The instruments are connected via a 2-wire line. A twisted 3-wire line is recommended for greater lengths or a larger number of instruments; the third line is used as a reference potential (GND) to compensate for any possible differences in potential that occur. Terminate every bus with a resistor using the software (see Parameterizing). Terminate every bus with a resistor using the software (see Parameterizing). The last device on the bus must provide the terminating resistor, i.e. in parameterizing (PIF), the last device must have the termination connected additionally within the bus connection (tr) and disconnected (notr) in all other devices. The last device on the bus must provide the terminating resistor, i.e. in parameterizing (PIF), the last device must have the termination connected additionally within the bus connection (tr) and disconnected (notr) in all other devices. If only one device is used, this is also effectively the last device and the terminating resistor must be connected (tr). All other technical data is given in RS 485 Operating Manual. If only one device is used, this is also effectively the last device and the terminating resistor must be connected (tr). All other technical data is given in RS 485 Operating Manual. USA and Canada: Use the MCB 17x conduit box for the power supply and relay/alarm contacts. Follow the installation instructions. 81 USA and Canada: Use the MCB 17x conduit box for the power supply and relay/alarm contacts. Follow the installation instructions. 81 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Installation Installation Installation instructions for the Oxi 170 Installation instructions for the Oxi 170 Terminal assignment Terminal assignment PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 Terminal assignment X1 A (RS 485 option) B (RS 485 option) GND (RS 485 option) Sens-Check Sens-Check K1 (R option) K1 (R option) K2 (R option) K2 (R option) N (mains) L1 (mains) – – PIN X2 REC 1 + REC 1 – REC 2 + REC 2 – a (sensor) b (sensor) c (sensor) d (sensor) e (sensor) f (sensor) g (sensor) h (sensor) i (sensor) 1 2 3 4 5 6 7 8 9 10 11 12 13 Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. Terminal assignment X1 A (RS 485 option) B (RS 485 option) GND (RS 485 option) Sens-Check Sens-Check K1 (R option) K1 (R option) K2 (R option) K2 (R option) N (mains) L1 (mains) – – X2 REC 1 + REC 1 – REC 2 + REC 2 – a (sensor) b (sensor) c (sensor) d (sensor) e (sensor) f (sensor) g (sensor) h (sensor) i (sensor) Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. Note: For power supplies above 24 VDC, use the following wiring: + 24 V L1 N GND Note: For power supplies above 24 VDC, use the following wiring: + 24 V L1 N GND 82 82 Oxi 170/ Oxi 296 Installation Oxi 170/ Oxi 296 Installation Connecting TriOxmatic® 690 or TriOxmatic® 70x sensors Connecting TriOxmatic® 690 or TriOxmatic® 70x sensors Oxi 170 Oxi 170 83 83 Oxi 170/ Oxi 296 Connecting the KI/S terminal box 1413 1)99 Oxi 170/ Oxi 296 Installation Connecting the KI/S terminal box 1413 S/c 1)99 C K 160 S/c C K 160 KI/S EK/AG or EK 170 max. cable length 100 m KI/S EK/AG or EK 170 max. cable length 100 m TriOxmatic® 690, TriOxmatic® 70x 84 Installation TriOxmatic® 690, TriOxmatic® 70x 84 Oxi 170/ Oxi 296 Installation Wiring KI/S Wiring KI/S Strip terminal 12 34567 Oxi 170/ Oxi 296 Installation 1 2 3 4 5 6 7 Colour of wires yellow gray + shield pink blue brown green white Strip terminal 12 34567 Note: After connection of the 8-wire EK 170 cable 1 wire remains unused. The unused "wire"should be fixed in position or pinched off. 1 2 3 4 5 6 7 Colour of wires yellow gray + shield pink blue brown green white Note: After connection of the 8-wire EK 170 cable 1 wire remains unused. The unused "wire"should be fixed in position or pinched off. Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. 85 Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. 85 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Installation Installation Installation instructions for the Oxi 296 Installation instructions for the Oxi 296 Terminal assignment Terminal assignment PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 Terminal assignment X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relay 1 Relay 1 Relay 2 Relay 2 N (mains) L1 (mains) – – PIN X2 REC 1 + REC 1 – REC 2 + REC 2 – a (sensor) b (sensor) c (sensor) d (sensor) e (sensor) f (sensor) g (sensor) h (sensor) i (sensor) 1 2 3 4 5 6 7 8 9 10 11 12 13 Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. Terminal assignment X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relay 1 Relay 1 Relay 2 Relay 2 N (mains) L1 (mains) – – X2 REC 1 + REC 1 – REC 2 + REC 2 – a (sensor) b (sensor) c (sensor) d (sensor) e (sensor) f (sensor) g (sensor) h (sensor) i (sensor) Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. Note: For power supplies above 24 VDC, use the following wiring: + 24 V L1 N GND Note: For power supplies above 24 VDC, use the following wiring: + 24 V L1 N GND 86 86 Installation Oxi 170/ Oxi 296 Installation Connecting the TriOxmatic® 690 or TriOxmatic® 70x Connecting the TriOxmatic® 690 or TriOxmatic® 70x Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 Terminal assignment X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relay 1 Relay 1 Relay 2 Relay 2 N (mains) L1 (mains) – – Oxi 170/ Oxi 296 Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. PIN X2 REC 1 + REC 1 – REC 2 + REC 2 – yellow green brown pink – blue black white – 1 2 3 4 5 6 7 8 9 10 11 12 13 87 Terminal assignment X1 A (RS 485) B (RS 485) GND (RS 485) Sens-Check Sens-Check Relay 1 Relay 1 Relay 2 Relay 2 N (mains) L1 (mains) – – X2 REC 1 + REC 1 – REC 2 + REC 2 – yellow green brown pink – blue black white – 87 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Installation Connecting the KI/S terminal box Installation Connecting the KI/S terminal box yellow green brown pink blue gray + shield white yellow green brown pink blue gray + shield white max. cable length 100 m max. cable length 100 m Cable EK/AG or EK 170 Probes that can be connected: TriOxmatic® 690 or TriOxmatic® 70x Cable EK/AG or EK 170 max. cable length 100 m Probes that can be connected: TriOxmatic® 690 or TriOxmatic® 70x Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. Terminal 1 2 3 4 5 6 7 8 9 10 11 12 13 88 X1 A (RS 485) B (RS 485) GND (RS 485) Relay 1 Relay 1 Relay 2 Relay 2 N (mains) L1 (mains) Terminal assignment X2 REC 1 + REC 1 – REC 2 + REC 2 – yellow green brown pink blue gray + shield white max. cable length 100 m Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. Terminal 1 2 3 4 5 6 7 8 9 10 11 12 13 88 X1 A (RS 485) B (RS 485) GND (RS 485) Relay 1 Relay 1 Relay 2 Relay 2 N (mains) L1 (mains) Terminal assignment X2 REC 1 + REC 1 – REC 2 + REC 2 – yellow green brown pink blue gray + shield white Oxi 170/ Oxi 296 Installation Oxi 170/ Oxi 296 Installation Wiring of KI/S Wiring of KI/S Strip terminal Colour of wires Strip terminal Colour of wires 1 2 3 4 5 6 7 yellow gray + shield pink blue brown green white 1 2 3 4 5 6 7 yellow gray + shield pink blue brown green white Note: After conncection of the 8-wire EK 170 1 wire remains unused. The unused “wire” should be fixed in position or pinched off. Note: After conncection of the 8-wire EK 170 1 wire remains unused. The unused “wire” should be fixed in position or pinched off. Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. 89 Unused wires must not jut into the housing. Otherwise, malfunctions can occur. This especially applies to the ground wire of the mains cable. Cut off unused wires in the housing as close to the armored thread joint as possible. 89 Oxi 170/ Oxi 296 Oxi 170/ Oxi 296 Configuration The configuration defines the operating mode of the instrument. To do this, the configuration level is split into submenus (see the flow diagram). The submenus only offer those setting options that have not yet been automatically established on the basis of the previous configuration of the program. Access to the configuration level can be protected via a code. The configuration defines the operating mode of the instrument. To do this, the configuration level is split into submenus (see the flow diagram). The submenus only offer those setting options that have not yet been automatically established on the basis of the previous configuration of the program. Access to the configuration level can be protected via a code. Perform the configuration with the instrument in a ready-to-operate condition, i.e.: the monitor is connected to the supply voltage and the measuring probe is connected. Factory settings Configuration Perform the configuration with the instrument in a ready-to-operate condition, i.e.: the monitor is connected to the supply voltage and the measuring probe is connected. Factory settings Adjustable function Setting Menu item Adjustable function Setting Menu item Salinity correction OFF CSA Salinity correction OFF CSA Measuring converter 690 CIN Measuring converter 690 CIN Measuring range final value 60.0 mg/l Crn Measuring range final value 60.0 mg/l Crn Measuring range of recorder output 1 0.0 ... 60.0 mg/l CR1 Measuring range of recorder output 1 0.0 ... 60.0 mg/l CR1 CR2 Temperature range of recorder output 21) 0.0 ... 50.0 °C nF REL1 Relay function2) (no function for rel. 1) nF REL2 (no function for rel. 2) Temperature range of recorder output 21) 0.0 ... 50.0 °C nF REL1 Relay function2) (no function for rel. 1) nF REL2 (no function for rel. 2) CRC 1) only in the T option 1) only in the T option 2) only in the Relay option 2) only in the Relay option 90 90 CR2 CRC Configuration Oxi 170/ Oxi 296 Configuration Calling up the configuration level Oxi 170/ Oxi 296 Calling up the configuration level − Press the DOWN key. − Press the DOWN key. − Press the ENTER key. − Press the ENTER key. The display shows the following: The display shows the following: The first numeral flashes. The first numeral flashes. No code number is set in the delivery state. To access the configuration level − press the ENTER key 3 times. No code number is set in the delivery state. To access the configuration level − press the ENTER key 3 times. If a code number was already set in an earlier parameterization, proceed as follows: − Set the first numeral using the UP / DOWN keys. − Press ENTER to confirm the input. If a code number was already set in an earlier parameterization, proceed as follows: − Set the first numeral using the UP / DOWN keys. − Press ENTER to confirm the input. − − Set the other two numerals in the same way. The following display appears: Set the other two numerals in the same way. The following display appears: − Use the UP / DOWN keys to change to C0 (configuration). − Use the UP / DOWN keys to change to C0 (configuration). − Press the ENTER key to confirm the input. − Press the ENTER key to confirm the input. If an incorrect code is entered or the ESCAPE key pressed, access to the configuration is made in the viewing mode. That is to say, settings can be inspected but not changed. 91 If an incorrect code is entered or the ESCAPE key pressed, access to the configuration is made in the viewing mode. That is to say, settings can be inspected but not changed. 91 !"# $%&' !"# ()* !"# $%&' !"# ()* Configuration Overview table of the submenus Display Configuration Overview table of the submenus Description Basic instrument Option Relay T option Display Description Basic instrument !"# Salinity correction + !"# Salinity correction + !$% Select measuring converter + !$% Select measuring converter + !&% Select measuring range final value + !&% Select measuring range final value + !'( Select recorder 1 + !'( Select recorder 1 + !') Select recorder 2 !') Select recorder 2 !'* + Assignment of the indicator relay + Operating mode of the indicator relay + !'* Option Relay T option + Assignment of the indicator relay + Operating mode of the indicator relay + + Menu appears in the corresponding model of the instrument. + Menu appears in the corresponding model of the instrument. 92 92 Configuration !"# $%&' !"# ()* Configuration Salinity correction Salinity correction The salinity correction is switched on or off in the !"# submenu: •! Correction ON •! Correction OFF ! !Note: !"# $%&' !"# ()* The salinity correction is switched on or off in the !"# submenu: •! Correction ON •! Correction OFF +% +** (delivery state) ! ! ote: N Principally , the Salinity Correction menu determines whether a salinity correction should be performed. If this is switched on (ON), an entry can be made in the parameterization (PSA). +% +** (delivery state) Principally , the Salinity Correction menu determines whether a salinity correction should be performed. If this is switched on (ON), an entry can be made in the parameterization (PSA). ! ! ! ! −! Use the UP / DOWN keys to select between !"# +% and !"# +**. −! Use the UP / DOWN keys to select between !"# +% and !"# +**. −! Use the ENTER key to continue with !$%. −! Use the ENTER key to continue with !$%. ! ! 93 93 !"# $%&' !"# ()* Selecting the sensor Sensor ,-+ TriOxmatic® 690 .++ TriOxmatic® 700 .+( TriOxmatic® 701 CellOx 700 Configuration Selecting the sensor The following setting options can be selected: Display !"# $%&' !"# ()* Configuration The following setting options can be selected: Display Sensor without REG and LECK detection ,-+ TriOxmatic® 690 without REG and LECK detection with .++ TriOxmatic® 700 with REG and LECK detection .+( TriOxmatic® 701 with REG and LECK detection with REG and LECK detection REG and LECK detection −! Press the UP / DOWN keys to select a sensor. −! Press the ENTER key to confirm the selection. CellOx 700 −! Press the UP / DOWN keys to select a sensor. −! Press the ENTER key to confirm the selection. Example: TriOxmatic® 690 Example: TriOxmatic® 690 Note: The instrument is equipped with REG and LECK detection that displays a sensor defect or whether a maintenance is due. Note: The instrument is equipped with REG and LECK detection that displays a sensor defect or whether a maintenance is due. 94 94 !"# $%&' !"# ()* Configuration Selecting the measuring range Selecting the measuring range The following setting possibilities are available in the !&% submenu: •! •! •! •! 60.0 mg/l 20.00 mg/l 600 % 200.0 % !"# $%&' !"# ()* Configuration The following setting possibilities are available in the !&% submenu: •! •! •! •! (only in TriOxmatic 701) (only in TriOxmatic 701) The following measuring ranges can be selected in the !&% menu depending on the sensor type: 60.0 mg/l 20.00 mg/l 600 % 200.0 % (only in TriOxmatic 701) (only in TriOxmatic 701) The following measuring ranges can be selected in the !&% menu depending on the sensor type: MBE 20.00 mg/l 690 700 701 x MBE 20.00 mg/l 690 700 701 x 60.0 mg/l x x x 60.0 mg/l x x x x 200.0 % x x x 600 % x x x 200.0 % 600 % −! Use the UP/DOWN keys to select the measuring range. −! Use the ENTER key to confirm it. x −! Use the UP/DOWN keys to select the measuring range. −! Use the ENTER key to confirm it. 95 95 !"# $%&' !"# ()* !"# $%&' !"# ()* Configuration Selecting the REC 1 recorder output Selecting the REC 1 recorder output If the recorder range is exceeded (OFL), the recorder outputs issue a constant signal of 20.5 mA. A return to the preset recorder range is performed automatically after eliminating the exceeding of the recorder range. Permissible recorder ranges depending on the measuring range: Measuring ranges REC ranges Minimum (measuring range start, MBA) Maximum (measuring range end, MBE) D/span (setting step size) *) Configuration If the recorder range is exceeded (OFL), the recorder outputs issue a constant signal of 20.5 mA. A return to the preset recorder range is performed automatically after eliminating the exceeding of the recorder range. Permissible recorder ranges depending on the measuring range: 200 % variable 0.0 % 600 % variable 0% 20.00 mg/l variable 0.00 mg/l 60.0 mg/l variable 0.0 mg/l 100.0 % to 200.0 % *) 100 % to 600 % *) 2.00 mg/l to 20.00 mg/l *) 5.0 mg/l to 60.0 mg/l *) 10.0 % 100 % 1.00 mg/l 5.0 mg/l Default settings Measuring ranges REC ranges Minimum (measuring range start, MBA) Maximum (measuring range end, MBE) D/span (setting step size) *) Setting for !&$: 200 % variable 0.0 % 600 % variable 0% 20.00 mg/l variable 0.00 mg/l 60.0 mg/l variable 0.0 mg/l 100.0 % to 200.0 % *) 100 % to 600 % *) 2.00 mg/l to 20.00 mg/l *) 5.0 mg/l to 60.0 mg/l *) 10.0 % 100 % 1.00 mg/l 5.0 mg/l Default settings Setting for !&$: −! Press the UP / DOWN keys to change the upper limit of the recorder range. −! Press ENTER to confirm the input. −! Press the UP / DOWN keys to change the upper limit of the recorder range. −! Press ENTER to confirm the input. Note: The final value of the lower recorder range has a fixed setting of 0 mg/l. Note: The final value of the lower recorder range has a fixed setting of 0 mg/l. 96 96 !"# $%&' !"# ()* Configuration !"# $%&' !"# ()* Configuration Selecting the REC 2 recorder output (only in T option) Selecting the REC 2 recorder output (only in T option) If the recorder range is exceeded (OFL), the recorder outputs issue a constant signal of 20.5 mA. A return to the preset recorder range is performed automatically after eliminating the exceeding of the recorder range. If the recorder range is exceeded (OFL), the recorder outputs issue a constant signal of 20.5 mA. A return to the preset recorder range is performed automatically after eliminating the exceeding of the recorder range. Permissible recorder ranges: Measuring ranges REC ranges Minimum (measuring range start MBA) Maximum (measuring range end MBE) Extent of the recorder range D/span (setting step size) *) **) Permissible recorder ranges: -5 ... +100 variable -5 °C *) to + 80 °C 25 °C to 100 °C **) min. 20 °C max. 105 °C 1 °C Measuring ranges REC ranges Minimum (measuring range start MBA) Maximum (measuring range end MBE) Extent of the recorder range D/span (setting step size) Default setting: 0 °C Default setting: 50 °C *) **) Setting: -5 ... +100 variable -5 °C *) to + 80 °C 25 °C to 100 °C **) min. 20 °C max. 105 °C 1 °C Default setting: 0 °C Default setting: 50 °C Setting: −! Press the UP / DOWN keys to change the upper value. −! Press ENTER to confirm the input. The lower set value appears: −! Press the UP / DOWN keys to change the upper value. −! Press ENTER to confirm the input. The lower set value appears: −! Press the UP / DOWN keys to change the lower value. −! Press ENTER to confirm the input. −! Press the UP / DOWN keys to change the lower value. −! Press ENTER to confirm the input. 97 97 !"# $%&' !"# ()* !"# $%&' !"# ()* Configuration Relay 1 / Relay 2 (R option) Selecting the relay functions A function can be assigned to each relay: Configuration Relay 1 / Relay 2 (R option) Selecting the relay functions A function can be assigned to each relay: Function +,-./#01#23 Function +,-./#01#23 %* (no function) Relay without any function %* (no function) Relay without any function /" (power supply) Contact is closed when power is applied and opens if there is a power fail /" (power supply) Contact is closed when power is applied and opens if there is a power fail *&! (freeze) Is active if the measured value is frozen - e.g. during calibration *&! (freeze) Is active if the measured value is frozen - e.g. during calibration (limits) !" (cleaning system) 98 (limits) Operates as an upper/ lower limit indicator and is active on exceeding/undercutting the rated value Relay is used to periodically control an external probe cleaning unit. The relay exclusively works as a normally open contact. During the cleaning process, the measured value remains frozen. !" (cleaning system) 98 Operates as an upper/ lower limit indicator and is active on exceeding/undercutting the rated value Relay is used to periodically control an external probe cleaning unit. The relay exclusively works as a normally open contact. During the cleaning process, the measured value remains frozen. !"# $%&' !"# ()* Configuration Regulating signals Regulating signals Limit indicator (UL.LL) Limit indicator (UL.LL) The following functions can be selected: Function UL O2 LL O2 UL °C LL °C The following functions can be selected: Description upper limit lower limit upper limit lower limit – – – – !"# $%&' !"# ()* Configuration Function main parameter main parameter temperature temperature UL O2 LL O2 UL °C LL °C Setting: Description upper limit lower limit upper limit lower limit – – – – main parameter main parameter temperature temperature Setting: −! Press the UP / DOWN keys to select the .00!relay function, e.g. for Relay 1. −! Press the UP / DOWN keys to select the .00!relay function, e.g. for Relay 1. −! Press ENTER to confirm the input. −! Press ENTER to confirm the input. REL1 REL1 −! Press the UP / DOWN keys to select the required limit function, O2 for Relay 1. e.g. O2 REL1 −! Press the UP / DOWN keys to select the required limit function, O2 for Relay 1. e.g. O2 −! Press ENTER to confirm the input. REL1 Select the switching direction (opener / closer) for FrC, UL.LL −! Press ENTER to confirm the input. Select the switching direction (opener / closer) for FrC, UL.LL The !&* submenu determines whether a relay functions as an opener or closer. The !&* submenu determines whether a relay functions as an opener or closer. −! Press the ENTER key to enter the !&* submenu. −! Press the ENTER key to enter the !&* submenu. −! Use the UP / DOWN keys to select between: CLOSER (C = Close) OPENER (O = Open) −! Use the UP / DOWN keys to select between: CLOSER (C = Close) OPENER (O = Open) −! Use the ENTER key to confirm the input. −! Use the ENTER key to confirm the input. −! Perform the setting for relay 2 in the same −! Perform the setting for relay 2 in the same way. way. 99 99 !"# $%&' !"# ()* !"# $%&' !"# ()* Parameterization The parameterization creates the numeric values of the functions for which the instrument is configured. Factory settings Parameterization The parameterization creates the numeric values of the functions for which the instrument is configured. Factory settings Adjustable function Setting Menu item Adjustable function Setting Menu item Salinity correction 2.0 /"# Salinity correction 2.0 /"# Recorder output 1: Current range/ attenuation 4 to 20 mA / 20mA/s /'( Recorder output 1: Current range/ attenuation 4 to 20 mA / 20mA/s /'( Recorder output 2: Current range/ attenuation Air correction 4 to 20 mA / 20 mA/S /') 4 to 20 mA / 20 mA/S /') 950 mbar //& Recorder output 2: Current range/ attenuation Air correction 950 mbar //& Settings of the RS 485 digital interface1) SLAVE 9600 Bd Ident 01 8 no (8 bit, no parity) made up of /(* Settings of the RS 485 digital interface1) SLAVE 9600 Bd Ident 01 8 no (8 bit, no parity) made up of /(* Code 000 /!1 Code 000 /!1 Temperature zero shift 0.0 °C /2 Temperature zero shift 0.0 °C /2 1) only in the RS option 1) only in the RS option 100 100 Parameterization !"# $%&' !"# ()* Parameterization Calling up the parameterization level Calling up the parameterization level −! Press the DOWN key. −! Press the DOWN key. −! Press the ENTER key. −! Press the ENTER key. ! !The display shows the following: ! ! ! he display shows the following: T ! !The first numeral flashes. !The first numeral flashes. ! o code number is set in the delivery state. N ! o access the configuration level T ! o code number is set in the delivery state. N ! o access the configuration level T −! press the ENTER key 3 times. ! −! press the ENTER key 3 times. !If a code number was already set in an earlier ! ! !If a code number was already set in an earlier ! parameterization, proceed as follows: parameterization, proceed as follows: ! ! ! ! ! ! −! Set the first numeral using the UP / DOWN keys. −! Press the ENTER key to confirm the input. −! Set the other two numerals in the same way. −! Set the first numeral using the UP / DOWN keys. −! Press the ENTER key to confirm the input. −! Set the other two numerals in the same way. ! !The following display appears: ! −! Press the ENTER key to confirm the input. ! ! ! !"# $%&' !"# ()* !The following display appears: −! Press the ENTER key to confirm the input. ! !If an incorrect code is entered or the ESCAPE key pressed, access to the ! ! configuration is made in the viewing mode. That is to say, settings can be inspected but not changed. ! !! ! !If an incorrect code is entered or the ESCAPE key pressed, access to the configuration is made in the viewing mode. That is to say, settings can be inspected but not changed. ! !! ! 101 101 !"# $%&' !"# ()* !"# $%&' !"# ()* Parameterization ! Overview table of the submenus !! D ! isplay !Description ! ! ! B ! asic instrument !+ !/"# /"# !/&$ /&$ !/&) /&) !/0 /0 !//& //& !/$* /$* ! !/2 /2 I!nput of salinity1) ! ecorder output 1 R ! ecorder output 2 R ! imiting value indicator L I!nput of the current ! ir pressure a ! S 485 interface R ! et up the code number S ! emperature T ! Overview table of the submenus !! O ! ptions ! !Relay D ! isplay !Description ! ! ! B ! asic instrument ! + !T option !RS 485 ! ! + ! ! ! ! ! ! ! ! !/"# /"# ! + ! ! ! + ! ! ! + ! ! ! ! + ! + ! ! ! ! ! ! + ! !/$* /$* ! ! !/2 /2 !/&$ /&$ !/&) /&) !/0 /0 !//& //& ! compensation /!" Parameterization I!nput of salinity1) ! ecorder output 1 R ! ecorder output 2 R !Limiting value indicator !Input of the current !air pressure !RS 485 interface !Set up the code number !Temperature O ! ptions !Relay ! !T option !RS 485 ! + ! ! !+ ! ! ! + ! ! ! ! + ! ! ! ! ! ! ! ! ! !+ !+ ! ! ! ! ! ! + ! ! ! compensation Timer for external probe cleaning unit /!" + Timer for external probe cleaning unit + ! ! Menu appears in the corresponding model of the instrument. + 1) ! Only appears in the setting (!"# +%) ! he sequence of parameterization can be seen in the flow diagram. T ! ! arameterization of salinity (only if !"# +%) P ! C ! orrection of the oxygen measurement depending on the salt content of the material ! !+ Menu appears in the corresponding model of the instrument. 1) ! Only appears in the setting (!"# +%) !The sequence of parameterization can be seen in the flow diagram. ! ! arameterization of salinity (only if !"# +%) P ! !Correction of the oxygen measurement depending on the salt content of the material being measured. being measured. −! Press the ENTER key when the /"# submenu appears: −! Press the ENTER key when the /"# submenu appears: ! ! −! Use the UP / DOWN keys to set the value ! between 2.0 and 70.0 (corresponds to ! 3.4 mS/cm ... 86.2 mS/cm at Tref 20°). ! ! ! −! Use the UP / DOWN keys to set the value ! between 2.0 and 70.0 (corresponds to ! 3.4 mS/cm ... 86.2 mS/cm at Tref 20°). −! Press the ENTER key to confirm the input. −! Press the ENTER key to confirm the input. ! ! ote: N ! !Note: ! ! ! 102 ! ! 102 Parameterization ! REC 1 and REC 2 recorder ! !This submenu enables the setting of: !"# $%&' !"# ()* Parameterization ! REC 1 and REC 2 recorder ! ! his submenu enables the setting of: T outputs •! Current range −! 0 to 20 mA −! 4 to 20 mA •! Attenuation [dI/dt] (dI = current change; dt = time change) •! Attenuation [dI/dt] (dI = current change; dt = time change) −! −! −! −! 0.1 mA/s 1 mA/s 5 mA/s 20 mA/s (= delivery state) !Note: Attenuation = changing speed of the recorder flow [mA/sec] on a sudden change of the input signal. Attenuation = changing speed of the recorder flow [mA/sec] on a sudden change of the input signal. ! ! etting: S ! −! Press the ENTER key when the /&( submenu appears: −! Press the ENTER key when the /&( submenu appears: −! Use the UP / DOWN keys to select the current range. ! −! Use the UP / DOWN keys to select the current range. −! Press the ENTER key to confirm the input. !! ! −! Use the UP / DOWN keys to select the attenuation. −! Press the ENTER key to confirm the input. ! −! Press the ENTER key to confirm the input. !! ! −! Press the ENTER key when the /&) submenu appears: ! 0.1 mA/s 1 mA/s 5 mA/s 20 mA/s (= delivery state) !Note: ! !Setting: ! ! outputs •! Current range −! 0 to 20 mA −! 4 to 20 mA −! −! −! −! !"# $%&' !"# ()* −! Use the UP / DOWN keys to select the attenuation. −! Press the ENTER key to confirm the input. ! −! Press the ENTER key when the /&) submenu appears: ! −! Set recorder output 2 in the same way as recorder output 1. −! Set recorder output 2 in the same way as recorder output 1. −! Press the ENTER key to confirm the input. ! −! Press the ENTER key to confirm the input. ! 103 103 !"# $%&' !"# ()* !"# $%&' !"# ()* Parameterization Parameterization Relay 1 / Relay 2 (instrument version R) Relay 1 / Relay 2 (instrument version R) Limit indicator (UL.LL) Limit indicator (UL.LL) The /0 submenu enables the allocation of the following values for the relay occupied by a limit function (UL.LL) in the configuration level: 1.! Limiting value L (Limit) 2.! Hysteresis HS (Hysteresis) 3.! Time delay Td (Time delay) The /0 submenu enables the allocation of the following values for the relay occupied by a limit function (UL.LL) in the configuration level: 1.! Limiting value L (Limit) 2.! Hysteresis HS (Hysteresis) 3.! Time delay Td (Time delay) The /0 submenu displays only the limit functions (UL or LL) that were selected in the configuration of the instrument submenu). (configuration level Þ Overview table: Nominal Hysteresis Time delay Nominal: Hysteresis: Time delay The /0 submenu displays only the limit functions (UL or LL) that were selected in the configuration of the instrument submenu). (configuration level Þ Overview table: Minimum: (UBE) Maximum: (OBE) Setting accuracy: lower measuring range final value Default: for the upper limits, the maximum, otherwise the minimum Minimum: Maximum: Setting accuracy: 0 10% of the meas. range (OBE - UBE) depends on the meas. value display Default: 0 Minimum: Maximum: Setting step: 0 sec 59 min 59 sec 1 sec Default: 0 sec Nominal upper measuring range final value depends on the meas. value display Upper or lower limiting value (nominal value) that is set up. Exceeding or undercutting the measuring signal of this value causes switching of the relevant relay programmed as a limit contact. Range above and below the set up nominal value that shifts the switching point of the relay. In this way, oscillation of the regulation is prevented. Time in seconds for which the value must be applied before a release is performed (by which the switching of the relay can be delayed). Hysteresis Time delay Nominal: Hysteresis: Time delay The input of these 3 values is subject to a compelled guidance. Even if no setting of hysteresis and time delay is planned (value = 0), you must pass through these submenus! 104 Minimum: (UBE) Maximum: (OBE) Setting accuracy: lower measuring range final value Default: for the upper limits, the maximum, otherwise the minimum Minimum: Maximum: Setting accuracy: 0 10% of the meas. range (OBE - UBE) depends on the meas. value display Default: 0 Minimum: Maximum: Setting step: 0 sec 59 min 59 sec 1 sec Default: 0 sec upper measuring range final value depends on the meas. value display Upper or lower limiting value (nominal value) that is set up. Exceeding or undercutting the measuring signal of this value causes switching of the relevant relay programmed as a limit contact. Range above and below the set up nominal value that shifts the switching point of the relay. In this way, oscillation of the regulation is prevented. Time in seconds for which the value must be applied before a release is performed (by which the switching of the relay can be delayed). The input of these 3 values is subject to a compelled guidance. Even if no setting of hysteresis and time delay is planned (value = 0), you must pass through these submenus! 104 Parameterization !"# $%&' !"# ()* Parameterization Setting the parameters for limit indicators Setting the parameters for limit indicators Example: Set up the upper limit for “O2“ on relay 1. Example: Set up the upper limit for “O2“ on relay 1. −! Press the ENTER key to enter the /0 submenu:: −! Press the ENTER key to enter the /0 submenu:: !"# $%&' !"# ()* −! Press the ENTER key again to set this limiting value. −! Press the ENTER key again to set this limiting value. The first/ second numeral flashes. (depending on the measuring range). The first/ second numeral flashes. (depending on the measuring range). −! Use the UP / DOWN keys to set the flashing digit of the limiting value and confirm it by pressing the ENTER key. −! Use the UP / DOWN keys to set the flashing digit of the limiting value and confirm it by pressing the ENTER key. −! Set the other numerals in the same way. −! Set the other numerals in the same way. −! Confirm the last numeral using the ENTER key when the 3" submenu appears. −! Confirm the last numeral using the ENTER key when the 3" submenu appears. −! Use the UP / DOWN keys to set the flashing numeral of the hysteresis. −! Use the UP / DOWN keys to set the flashing numeral of the hysteresis. −! Press the ENTER key to confirm the input. −! Press the ENTER key to confirm the input. −! Set the other numerals in the same way. −! Set the other numerals in the same way. −! Confirm the last numeral using the ENTER key when the 24 submenu appears. −! Confirm the last numeral using the ENTER key when the 24 submenu appears. Setting range: 0 to 10 % of the measuring range. Setting range: 0 to 10 % of the measuring range. −! Use the UP / DOWN keys to set the seconds (right-hand flashing digits) of the switching delay. −! Use the UP / DOWN keys to set the seconds (right-hand flashing digits) of the switching delay. −! Press the ENTER key to confirm the input. −! Press the ENTER key to confirm the input. −! Set the minutes (two numerals on the left) in the same way. −! Set the minutes (two numerals on the left) in the same way. Setting range: 0 to 59 min 59 sec. Setting range: 0 to 59 min 59 sec. 105 105 !"# $%&' !"# ()* !"# $%&' !"# ()* Parameterization Example: Rel 1: Rel 2: Example: UL = 10 mg/l LL = 5 mg/l HS = 1 mg/l HS = 1 mg/l td = 0 td = 0 Rel 1: Rel 2: Measured value UL = 10 mg/l LL = 5 mg/l td = 0 td = 0 1 Rel1 10 mg/l set OG hysteresis 11 mg/l 44UL = upper limit 10 mg/l 9 mg/l Rel1 set OG hysteresis 44UL = upper limit 9 mg/l 4 2 6 mg/l HS = 1 mg/l HS = 1 mg/l Measured value 1 11 mg/l Parameterization Measured value Rel2 6 mg/l 5 mg/l 4 mg/l 4 2 LL = lower limit 5 mg/l set UG hysteresis 4 mg/l 3 Measured value Rel2 LL = lower limit set UG hysteresis 3 Time Time $444"##$%!&'(')!'*+',-).%!/0'),1$/44444444444444(444"##$%!&'(')!'*+',-).%!/0'),1$/!2-,3 $444"##$%!&'(')!'*+',-).%!/0'),1$/44444444444444(444"##$%!&'(')!'*+',-).%!/0'),1$/!2-,3 54444.0$%!&'(')!'*+',-).%!/0'),1$/4444444444444464444.0$%!&'(')!/0'),1$/!2-,3 54444.0$%!&'(')!'*+',-).%!/0'),1$/4444444444444464444.0$%!&'(')!/0'),1$/!2-,3 106 106 Parameterization !"# $%&' !"# ()* Parameterization Entering the manual pressure compensation !"# $%&' !"# ()* Entering the manual pressure compensation Alternatively, the current air pressure (absolute pressure!) or the site elevation (above the normal zero point) can be entered. In entering the air pressure, the default value for the site elevation is automatically adapted and vice versa. Entering the air pressure Alternatively, the current air pressure (absolute pressure!) or the site elevation (above the normal zero point) can be entered. In entering the air pressure, the default value for the site elevation is automatically adapted and vice versa. Entering the air pressure −! Use the ENTER key to call up the //& submenu: −! Use the ENTER key to call up the //& submenu: −! The first digit flashes. −! Use the UP / DOWN keys to set the flashing digit. −! Press the ENTER key to confirm the input. −! Set the other digits in the same way. −! The first digit flashes. −! Use the UP / DOWN keys to set the flashing digit. −! Press the ENTER key to confirm the input. −! Set the other digits in the same way. Setting range: Setting range: 500 mbar to 1100 mbar 500 mbar to 1100 mbar Entering the elevation Entering the elevation −! Use the ENTER key to call up the /#0 submenu: −! Use the ENTER key to call up the /#0 submenu: −! The first digit flashes. −! Use the UP / DOWN keys to set the flashing digit. −! Press the ENTER key to confirm the input. −! Set the other digits in the same way −! The first digit flashes. −! Use the UP / DOWN keys to set the flashing digit. −! Press the ENTER key to confirm the input. −! Set the other digits in the same way Setting range: Setting range: -700 m to 5600 m -700 m to 5600 m 107 107 !"# $%&' !"# ()* !"# $%&' !"# ()* Parameterization RS 485 interface (RS option) Parameterization RS 485 interface (RS option) The parameterization of the RS 485 interface is described in a separate manual that is included within the scope of delivery of instruments with a RS 485 interface (RS instrument version). Setting up the code The parameterization of the RS 485 interface is described in a separate manual that is included within the scope of delivery of instruments with a RS 485 interface (RS instrument version). Setting up the code The setting of a code prevents changes to the configuration and parameterization of the instrument by the unintentional or erroneous pressing of an input key. On entering the configuration / parameterization, the code number must be entered by the user (see Calling up the configuration level / Calling up the parameterization level). No code is set in the delivery state. Thus, the configuration and parameterization of the instrument is not protected. Only after a code number has been input is the instrument protected against unintended or unauthorized changes. The setting of a code prevents changes to the configuration and parameterization of the instrument by the unintentional or erroneous pressing of an input key. On entering the configuration / parameterization, the code number must be entered by the user (see Calling up the configuration level / Calling up the parameterization level). No code is set in the delivery state. Thus, the configuration and parameterization of the instrument is not protected. Only after a code number has been input is the instrument protected against unintended or unauthorized changes. Setting: Setting: −! Call up the /!4 submenu using ENTER: −! Call up the /!4 submenu using ENTER: −! The current code number appears on the display (delivery state: +++). The first numeral flashes. −! Set the first numeral using the UP / DOWN keys. −! Press the ENTER key to confirm the input. −! The current code number appears on the display (delivery state: +++). The first numeral flashes. −! Set the first numeral using the UP / DOWN keys. −! Press the ENTER key to confirm the input. Note: (The code number 555 is not permitted!) Note: (The code number 555 is not permitted!) −! Set the other two numerals in the same −! Set the other two numerals in the same way. way. Note: After a code number has been entered, the instrument can only be configured or parameterized using this new code! Note: After a code number has been entered, the instrument can only be configured or parameterized using this new code! Lifting the code number lock The code number lock can only be entered by removing the reset in the delivery state again. To do this, enter the code number +++. Lifting the code number lock The code number lock can only be entered by removing the reset in the delivery state again. To do this, enter the code number +++. 108 108 Parameterization !"# $%&' !"# ()* Parameterization Temperature compensation !"# $%&' !"# ()* Temperature compensation The /2 submenu enables compensation of the temperature measuring sensor tolerances in the test probe (shifting of the zero point by a maximum of 0.5 °C). The /2 submenu enables compensation of the temperature measuring sensor tolerances in the test probe (shifting of the zero point by a maximum of 0.5 °C). Place the measuring probe in a vessel containing at least 2 liters of water due to its thermal capacity. Place the measuring probe in a vessel containing at least 2 liters of water due to its thermal capacity. Leave the measuring probe and reference thermometer in the water for at least 15 minutes, or with temperature differences between the water and test probe > 10 °C for at least 1 hour, and stir the water occasionally until the comparison can be made. Leave the measuring probe and reference thermometer in the water for at least 15 minutes, or with temperature differences between the water and test probe > 10 °C for at least 1 hour, and stir the water occasionally until the comparison can be made. Setting: Setting: −! Use ENTER to call up the /2 submenu: −! Use ENTER to call up the /2 submenu: −! Use the UP / DOWN keys to set the value (± 0.5 °C). At the same time, the corrected measured value (upper line) and the correction value (lower line) are displayed. −! Use the UP / DOWN keys to set the value (± 0.5 °C). At the same time, the corrected measured value (upper line) and the correction value (lower line) are displayed. −! Press the ENTER key to confirm the input. −! Press the ENTER key to confirm the input. 109 109 !"# $%&' !"# ()* !"# $%&' !"# ()* Parameterization Timer for an external probe cleaning unit (CS) Parameterization Timer for an external probe cleaning unit (CS) The /0 submenu allows for the allocation of the intervals for relays, which are configured in the configuration level to work as control relay for an external probe cleaning unit (CS). The /0 submenu allows for the allocation of the intervals for relays, which are configured in the configuration level to work as control relay for an external probe cleaning unit (CS). The following intervals can be set: The following intervals can be set: Parameter Range Meaning Parameter Range Meaning 2& 1 ... 168 h Interval between two cleaning processes. 2& 1 ... 168 h Interval between two cleaning processes. 26 1 ... 300 s Duration of the cleaning process. During the cleaning process, the measured value remains frozen. 26 1 ... 300 s Duration of the cleaning process. During the cleaning process, the measured value remains frozen. 27 1 ... 900 s Interval for keeping the measured value frozen after the cleaning process is finished. 27 1 ... 900 s Interval for keeping the measured value frozen after the cleaning process is finished. During 26 and 27 no calibration is possible. If a cleaning process is to be started while a calibration is running, the start is delayed until the calibration is finished. 110 During 26 and 27 no calibration is possible. If a cleaning process is to be started while a calibration is running, the start is delayed until the calibration is finished. 110 Parameterization !"# $%&' !"# ()* Parameterization Setting the intervals 82& (9) Setting the intervals −! Press the ENTER key. The menu to input the cleaning interval appears with the 2& display and the current value in the lower display line. /!" REL1 !"# $%&' !"# ()* −! The first digit flashes. −! Using the UP / DOWN keys set the flashing digit. −! Confirm using ENTER. −! Set the other digits in the same way. −! After the last digit has been confirmed the menu switches to the input of the cleaning duration (26 display). This value is set in the same way. −! Press the ENTER key. The menu to input the cleaning interval appears with the 2& display and the current value in the lower display line. /!" 82& (9) REL1 −! The first digit flashes. −! Using the UP / DOWN keys set the flashing digit. −! Confirm using ENTER. −! Set the other digits in the same way. −! After the last digit has been confirmed the menu switches to the input of the cleaning duration (26 display). This value is set in the same way. Finally the additional waiting time is set up (27 display). Finally the additional waiting time is set up (27 display). −! After the last pressing of the ENTER key the start menu of the parameterization level appears (/# display). −! After the last pressing of the ENTER key the start menu of the parameterization level appears (/# display). 111 111 !"# $%&' !"# ()* !"# $%&' !"# ()* Viewing Mode In the viewing mode, settings can be inspected without having to input a code. However, the settings cannot be modified. Displaying the parameterization and configuration data Viewing Mode In the viewing mode, settings can be inspected without having to input a code. However, the settings cannot be modified. Displaying the parameterization and configuration data −! Press the DOWN key. −! Press the DOWN key. −! Press the ENTER key when the first numeral flashes. −! Press the ENTER key when the first numeral flashes. −! Press the ESCAPE key. −! Press the ESCAPE key. −! Use the UP / DOWN keys to change between the parameterization /# and configuration !+. −! Use the UP / DOWN keys to change between the parameterization /# and configuration !+. −! Press the ENTER key to run through the submenus. −! Press the ENTER key to run through the submenus. Displaying the calibration data and software version By pressing the ENTER key in the measuring mode, the display of the sensor slope appears: Displaying the calibration data and software version By pressing the ENTER key in the measuring mode, the display of the sensor slope appears: S S :+. :+. −! Use the UP / DOWN keys to call up the "; submenu: −! Use the UP / DOWN keys to call up the "; submenu: −! Press the M key to return to the measuring mode. −! Press the M key to return to the measuring mode. 112 112 Measuring Mode !"# $%&' !"# ()* Measuring Mode The Oxi 170 and Oxi 296 instruments are automatically set to the measuring mode following the first commissioning. Otherwise, the measuring mode - except in compelled guidance - can be called up from any operating level by pressing the M key (see also section, Operating instructions). 113 !"# $%&' !"# ()* The Oxi 170 and Oxi 296 instruments are automatically set to the measuring mode following the first commissioning. Otherwise, the measuring mode - except in compelled guidance - can be called up from any operating level by pressing the M key (see also section, Operating instructions). 113 !"# $%&' !"# ()* !"# $%&' !"# ()* Calibration Calibration −! Remove the sensor from the measuring medium and prepare it for calibration in the air (clean it if necessary and wait for the temperature adjusting). −! Remove the sensor from the measuring medium and prepare it for calibration in the air (clean it if necessary and wait for the temperature adjusting). −! Use the C key to change to the calibrating mode. −! Use the C key to change to the calibrating mode. !#0 !#0 Note: The calibration can be terminated by pressing the ESCAPE key. Auto Cal S Auto Cal !#0 <=Auto Cal S S – Use the ENTER key to start the calibration. AR flashes. The sensor slope is determined. !#0 !#0 <=Auto Cal The measurement runs until a stable measurement value is reached (AR flashes). <=- – Use the ENTER key to start the calibration. AR flashes. The sensor slope is determined. The measurement runs until a stable measurement value is reached (AR flashes). Note: The slope reproduces the status of the sensor and is accepted within the range of 0.5 to 1.4. Note: The slope reproduces the status of the sensor and is accepted within the range of 0.5 to 1.4. Duration of the calibrating process: Min. 60 sec to max. 15 min (If no stable measured value is achieved after 15 minutes, the "!#0 >''" error message appears, see the chapter Display after an invalid calibration. Duration of the calibrating process: Min. 60 sec to max. 15 min (If no stable measured value is achieved after 15 minutes, the "!#0 >''" error message appears, see the chapter Display after an invalid calibration. S Stable measured value accepted. AR goes out. !#0 <=- Auto Cal Stable measured value accepted. AR goes out. Auto Cal To ensure a high degree of accuracy, it is recommended to set the current air pressure (absolute pressure!) in //& before the calibration. 114 Note: The calibration can be terminated by pressing the ESCAPE key. To ensure a high degree of accuracy, it is recommended to set the current air pressure (absolute pressure!) in //& before the calibration. 114 Calibration !#0 – :5 – !"# $%&' !"# ()* Calibration Pressing the ENTER key causes the measured value to be displayed. However, the current outputs do not yet follow the current measured value. Sensors can now be replaced in the measuring medium. !#0 – Pressing the ENTER key causes the measured value to be displayed. However, the current outputs do not yet follow the current measured value. Sensors can now be replaced in the measuring medium. – Use the ENTER or M key to return to the normal measuring mode. The recorder outputs then follow the current measured value. :5 Use the ENTER or M key to return to the normal measuring mode. The recorder outputs then follow the current measured value. Calibration error, !#0 >&& Calibration error, !#0 >&& The !#0 >&& error message appears if The !#0 >&& error message appears if •! no stable measured value was reached or •! non-admissible values were measured for the slope and offset voltage. !"# $%&' !"# ()* •! no stable measured value was reached or •! non-admissible values were measured for the slope and offset voltage. −! Use the ENTER key after the error has been eliminated to repeat the calibration. 115 −! Use the ENTER key after the error has been eliminated to repeat the calibration. 115 !"# $%&' !"# ()* !"# $%&' !"# ()* Checking Mode Calling up the checking mode Checking Mode Calling up the checking mode −! Hold the ESCAPE key down and briefly press the UP key to call up the checking mode. −! Hold the ESCAPE key down and briefly press the UP key to call up the checking mode. −! Leave the checking mode again by pressing the M or C key. −! Leave the checking mode again by pressing the M or C key. Variant identification Variant identification If the 56!symbol appears at the top left of the display, the 56!hardware was recognized and the testing is started with the display of the code number. If the 56!symbol appears at the top left of the display, the 56!hardware was recognized and the testing is started with the display of the code number. If the 56 hardware was not identified, the following error message appears: If the 56 hardware was not identified, the following error message appears: >&& #;/2: Hardware error !" −! Contact the technical customer service >&& #;/2: Hardware error !" at WTW. Displaying the code number The code number is displayed in the !;4 submenu after pressing the ENTER key: !" 116 −! Press the ENTER key again to continue with recorder output 1. −! Contact the technical customer service at WTW. Displaying the code number The code number is displayed in the !;4 submenu after pressing the ENTER key: !" 116 −! Press the ENTER key again to continue with recorder output 1. Checking Mode !"# $%&' !"# ()* Checking Mode Recorder output 1 !"# $%&' !"# ()* Recorder output 1 After pressing the ENTER key, a current of 0.1 mA is set in the 2"2 &>!( submenu: After pressing the ENTER key, a current of 0.1 mA is set in the 2"2 &>!( submenu: −! Press M to set the current to 0.1 mA. −! Press C to set the current to 10.0 mA. −! Press UP to increase the current (max. 20.5 mA). −! Press M to set the current to 0.1 mA. −! Press C to set the current to 10.0 mA. −! Press UP to increase the current (max. 20.5 mA). !" !" −! Press DOWN to decrease the current (min. 0.0 mA). −! Press DOWN to decrease the current (min. 0.0 mA). −! Press the ENTER key again to continue with −! Press the ENTER key again to continue with recorder output 2. recorder output 2. Recorder output 2 Recorder output 2 A current of 0.1 mA is set in the 2"2 &>!) submenu after pressing the ENTER key: !" −! Press M to set the current to 0.1 mA. −! Press C to set the current to 10.0 mA. −! Press UP to increase the current (max. 20.5 mA). A current of 0.1 mA is set in the 2"2 &>!) submenu after pressing the ENTER key: !" −! Press M to set the current to 0.1 mA. −! Press C to set the current to 10.0 mA. −! Press UP to increase the current (max. 20.5 mA). −! Press DOWN to decrease the current (min. 0.0 mA). −! Press DOWN to decrease the current (min. 0.0 mA). −! Press the ENTER key again to continue with −! Press the ENTER key again to continue with relay test. relay test. 117 117 !"# $%&' !"# ()* Relay test Note: Rel 1 and Rel 2 are only addressed if the control option is present. After pressing the ENTER key, the 2"28message flashes in the 2"2 &>08submenu: !" If a relay is switched on, the relevant symbol appears on the display. −! Press the ESCAPE key: Relay 1 on/off −! Press the ESCAPE key: Relay 1 on/off −! Press the UP key: Relay 2 on/off −! Press the UP key: Relay 2 on/off −! Press the DOWN key: −! Press the DOWN key: Sens-Check E/A −! Press the ENTER key to continue with RS485. RS 485 −! Press the ENTER key to continue with RS485. RS 485 After pressing the ENTER key, the 2"28message flashes in the 2"2 9=58submenu: 118 Note: Rel 1 and Rel 2 are only addressed if the control option is present. If a relay is switched on, the relevant symbol appears on the display. Sens-Check E/A !" Checking Mode Relay test After pressing the ENTER key, the 2"28message flashes in the 2"2 &>08submenu: !" !"# $%&' !"# ()* Checking Mode Note: The menu item only appears if the RS 485 interface is present. After pressing the ENTER key, the 2"28message flashes in the 2"2 9=58submenu: !" Note: The menu item only appears if the RS 485 interface is present. The RS 485 operates in the test mode as a repeater, i.e. all the blocks received are sent back again. The RS 485 operates in the test mode as a repeater, i.e. all the blocks received are sent back again. −! Press the ESCAPE key: Sends the instrument identification according to the "RSID" RS command (with RS 485 protocol). −! Press the UP key: Sends the instrument identification according to the "RSID" RS command (without RS 485 protocol; for printer output). −! Press the ENTER key: This terminates the RS 485 test to continue with Displaying the code number. −! Press the ESCAPE key: Sends the instrument identification according to the "RSID" RS command (with RS 485 protocol). −! Press the UP key: Sends the instrument identification according to the "RSID" RS command (without RS 485 protocol; for printer output). −! Press the ENTER key: This terminates the RS 485 test to continue with Displaying the code number. 118 !"# $%&' !"# ()* Checking Mode !"# $%&' !"# ()* Checking Mode Flowchart Flowchart : -(,*(%.#%/ #,0#%%1%2 !#$$#% : -(,*(%.#%/ #,0#%%1%2 3()$45# 6(,78(,# 96/6(,78(,# #,0(%%. ! " !#$$#% 3()$45# 6(,78(,# 96/6(,78(,# #,0(%%. ! !#$$#% & '()*+,*#,#% 119 " !#$$#% & '()*+,*#,#% 119 !"# $%&' !"# ()* !"# $%&' !"# ()* Cleaning / Maintenance Cleaning / Maintenance Cleaning / Maintenance Cleaning / Maintenance The Oxi 170 and Oxi 296 instruments are largely maintenance-free. Some instructions are given here on taking care of the instruments: The Oxi 170 and Oxi 296 instruments are largely maintenance-free. Some instructions are given here on taking care of the instruments: −! Keep the instruments free from dust and dirt as far as possible. −! Keep the instruments free from dust and dirt as far as possible. −! Do not use a high-pressure cleaner to clean the housing. −! Do not use a high-pressure cleaner to clean the housing. −! Do not use any cleaning agent that contains solvent. −! Do not use any cleaning agent that contains solvent. −! Follow the details given in the sensor operating manual on the cleaning and maintenance of the sensors! −! Follow the details given in the sensor operating manual on the cleaning and maintenance of the sensors! −! Check the instruments regularly for mechanical damage and, if necessary, take them out of service. −! Check the instruments regularly for mechanical damage and, if necessary, take them out of service. −! Follow the safety instructions even when carrying out cleaning activities! −! Follow the safety instructions even when carrying out cleaning activities! 120 120 !"# $%&' !"# ()* Troubleshooting !"# $%&' !"# ()* Troubleshooting The following messages could occur (shown in order of priority): The following messages could occur (shown in order of priority): Message Reason Measure Message Reason Measure >&& Serious error that does not permit any further measuring −! Send the instrument to WTW >&& Serious error that does not permit any further measuring −! Send the instrument to WTW !#0 No valid calibration exists −! Calibrate the instrument again (see also the chapter, Calibration) !#0 No valid calibration exists −! Calibrate the instrument again (see also the chapter, Calibration) >&& >&& +*0 The O2/ temperature value lies outside the measuring range (Overflow) −! Check the sensor and sensor connection +*0 The O2/ temperature value lies outside the measuring range (Overflow) −! Check the sensor and sensor connection Measured value flashes An overflow is present on the corresponding recorder output −! Adjust the recorder range Measured value flashes An overflow is present on the corresponding recorder output −! Adjust the recorder range Maintain sensor (REG) −! For help, see the sensor operating manual Maintain sensor (REG) −! For help, see the sensor operating manual Sensor possibly defective (LEAK) −! For help, see the sensor operating manual Sensor possibly defective (LEAK) −! For help, see the sensor operating manual Hardware error −! Send the instrument to WTW Hardware error −! Send the instrument to WTW >&& #;/2 121 >&& #;/2 121 !"# $%&' !"# ()* !"# $%&' !"# ()* Technical Data Technical data for Oxi 170 Technical Data Technical data for Oxi 170 ;;; == ><? == Display Measured value Units, settings Accuracy Automatic temperature compensation Manual compressed air compensation Reference temperature Calibration Calibrating range 122 ;;; == ><? == Display LCD 7 segment •! O2 •! Temperature Symbols Measured value 3-digit 4-digit O2 measurement Signal input Display and measuring range Measured value resolution @A == ><? == @A == ><? == ;<; == ;;; == ;<; == ;;; == Units, settings LCD 7 segment •! O2 •! Temperature Symbols 3-digit 4-digit O2 measurement Low impedance 0.0 to (20) 60 mg/l; 0 to (200) 600% depending on the sensor type 0.1 mg/l, 0.01 mg/l; 1%, 0.1% depending on the sensor type ± 1% of measured value ± 1 digit NTC - 5 to + 100°C 500 mbar to 1100 mbar + 20°C Air calibration acc. to OxiCal procedure Slope of 0.5 to 1.4 Signal input Display and measuring range Measured value resolution Accuracy Automatic temperature compensation Manual compressed air compensation Reference temperature Calibration Calibrating range 122 Low impedance 0.0 to (20) 60 mg/l; 0 to (200) 600% depending on the sensor type 0.1 mg/l, 0.01 mg/l; 1%, 0.1% depending on the sensor type ± 1% of measured value ± 1 digit NTC - 5 to + 100°C 500 mbar to 1100 mbar + 20°C Air calibration acc. to OxiCal procedure Slope of 0.5 to 1.4 !"# $%&' !"# ()* Technical Data Temperature measurement Temperature sensor Accuracy Resolution !"# $%&' !"# ()* Technical Data Temperature measurement NTC integrated in the sensor ± 0.2 K ± 1 digit Additional fine adjustment of ± 0.5 K 0.1 K Temperature sensor Accuracy Resolution Inputs / outputs NTC integrated in the sensor ± 0.2 K ± 1 digit Additional fine adjustment of ± 0.5 K 0.1 K Inputs / outputs Sensor input Contact outputs 7-contact round plug connection with screw fixing SENS-CHECK relay Closes on sensor defect Relay 1/ Relay 2 Functions, limit controller •! Max. switching voltage 250 VAC •! Max. switching current 5 A •! Max. switching capacity 150 W (resistive load) Sensor input Contact outputs 7-contact round plug connection with screw fixing SENS-CHECK relay Closes on sensor defect Relay 1/ Relay 2 Functions, limit controller •! Max. switching voltage 250 VAC •! Max. switching current 5 A •! Max. switching capacity 150 W (resistive load) Signal outputs 0/4 to 20 mA; electrically isolated from the input; Recorder ranges and recorder attenuation can be set via software •! Basic accuracy 0.1% •! Load max. 600 Ohm •! Load effect < 0.1 % Signal outputs 0/4 to 20 mA; electrically isolated from the input; Recorder ranges and recorder attenuation can be set via software •! Basic accuracy 0.1% •! Load max. 600 Ohm •! Load effect < 0.1 % Connector terminals Accessible after opening the instrument; Cable inlet with 4 PG screws ² Connector cross section 0.5 to 2.5 mm •! Power supply 2-contact •! Relay 1/2 each 2-contact •! SENS-CHECK 2-contact •! Recorder connections each 2-contact •! Sensor 7-contact Connector terminals Accessible after opening the instrument; Cable inlet with 4 PG screws ² Connector cross section 0.5 to 2.5 mm •! Power supply 2-contact •! Relay 1/2 each 2-contact •! SENS-CHECK 2-contact •! Recorder connections each 2-contact •! Sensor 7-contact Protection type Protection type Lightning protector (inputs and outputs) •! Coarse protection 90 V / 1.5 KA (8/20µs) •! Fine protection 600 Watt Lightning protector (inputs and outputs) •! Coarse protection 90 V / 1.5 KA (8/20µs) •! Fine protection 600 Watt Electrical instrument protection Housing Safety class Electrical instrument protection Housing Safety class 2 according to IEC 1010 IP 66 123 2 according to IEC 1010 IP 66 123 !"# $%&' !"# ()* !"# $%&' !"# ()* Technical Data Technical Data Electrical connection data Electrical connection data •! 230 VAC (– 15% + 10%) Voltage supply (depending on the instrument •! 115 VAC (– 15% + 10%) •! 24 VAC (– 15% + 10%) version) •! 24 VDC (– 30% + 20%) Frequency 48 to 62 Hz Power consumption Max. 18 Watt Test certificates UL, cUL (for 115 VAC, 24 VAC and 24 VDC) CE (for all supply voltages) Interference suppression According to EN 50081-1 Interference immunity According to EN 50082-2, Namur recommendations •! 230 VAC (– 15% + 10%) Voltage supply (depending on the instrument •! 115 VAC (– 15% + 10%) •! 24 VAC (– 15% + 10%) version) •! 24 VDC (– 30% + 20%) Frequency 48 to 62 Hz Power consumption Max. 18 Watt Test certificates UL, cUL (for 115 VAC, 24 VAC and 24 VDC) GS, CE (for all supply voltages) Interference suppression According to EN 50081-1 Interference immunity According to EN 50082-2, Namur recommendations Ambient temperature Limits of operating range Storage and transport temperature Climate class Ambient temperature Limits of operating range Storage and transport temperature Climate class Mechanical data Dimensions Weight Keypad (material) Housing (material) 124 – 25 °C to + 55 °C – 25 °C to + 65 °C Climate class 4, VDI / VDE 3540 Bl.2 222 x 238 (202) x 105 mm (B x H x T) (height in parentheses without PG screws) Approx. 2.2 kg Polyester Polycarbonate Mechanical data Dimensions Weight Keypad (material) Housing (material) 124 – 25 °C to + 55 °C – 25 °C to + 65 °C Climate class 4, VDI / VDE 3540 Bl.2 222 x 238 (202) x 105 mm (B x H x T) (height in parentheses without PG screws) Approx. 2.2 kg Polyester Polycarbonate !"# $%&' !"# ()* Technical Data Technical data for Oxi 296 Technical data for Oxi 296 Display Measured value Units, settings Display LCD 7 segment •! O2 •! Temperature Symbols Measured value 3-digit 4-digit Units, settings O2 measurement Signal input Display and measuring range Measured value resolution Accuracy Automatic temperature compensation Manual compressed air compensation Reference temperature Calibration Calibration range !"# $%&' !"# ()* Technical Data LCD 7 segment •! O2 •! Temperature Symbols 3-digit 4-digit O2 measurement Low resistance 0.0 to (20) 60 mg/l; 0 to (200) 600% depending on the sensor type 0.1 mg/l, 0.01 mg/l; 1%, 0.1% depending on the sensor type ± 1% of measured value ± 1 digit NTC - 5 to + 100°C •! Air pressure: 500 mbar to 1100 mbar •! Elevation: - 698 m to 5573 m + 20°C Air calibration according to the OxiCal procedure Slope of 0.5 to 1.4 125 Signal input Display and measuring range Measured value resolution Accuracy Automatic temperature compensation Manual compressed air compensation Reference temperature Calibration Calibration range Low resistance 0.0 to (20) 60 mg/l; 0 to (200) 600% depending on the sensor type 0.1 mg/l, 0.01 mg/l; 1%, 0.1% depending on the sensor type ± 1% of measured value ± 1 digit NTC - 5 to + 100°C •! Air pressure: 500 mbar to 1100 mbar •! Elevation: - 698 m to 5573 m + 20°C Air calibration according to the OxiCal procedure Slope of 0.5 to 1.4 125 !"# $%&' !"# ()* Temperature measurement Temperature sensor Accuracy Resolution !"# $%&' !"# ()* Technical Data Technical Data Temperature measurement NTC integrated in the sensor ± 0.2 K ± 1 digit Additional fine adjustment of ± 0.5 K 0.1 K Inputs / outputs Temperature sensor Accuracy Resolution NTC integrated in the sensor ± 0.2 K ± 1 digit Additional fine adjustment of ± 0.5 K 0.1 K Inputs / outputs Digital interface RS-485; 2(3)- wire connection Bus operation is possible with up to 31 units Digital interface RS-485; 2(3)- wire connection Bus operation is possible with up to 31 units Contact outputs SENS-CHECK relay closes on sensor defect Relay 1/ relay 2 functions, limit controller •! Max. switching voltage 250 VAC •! Max. switching current 5 A •! Max. switching capacity 150 W (resistive load) Contact outputs SENS-CHECK relay closes on sensor defect Relay 1/ relay 2 functions, limit controller •! Max. switching voltage 250 VAC •! Max. switching current 5 A •! Max. switching capacity 150 W (resistive load) Signal outputs 0/4 to 20mA; electrically isolated from the input; Recorder ranges and recorder attenuation can be set via software •! Basic accuracy 0.1% •! Load max. 600 Ohm •! Load effect < 0.1 % Signal outputs 0/4 to 20mA; electrically isolated from the input; Recorder ranges and recorder attenuation can be set via software •! Basic accuracy 0.1% •! Load max. 600 Ohm •! Load effect < 0.1 % Connection terminals Accessible on the instrument backplate Connector cross section 0.5 to 2.5 mm² •! Power supply 2-contact •! Relay 1/2 each 2-contact •! SENS-CHECK 2-contact •! RS-485 3-contact •! Recorder connections each 2-contact •! Sensor 7-contact Connection terminals Accessible on the instrument backplate Connector cross section 0.5 to 2.5 mm² •! Power supply 2-contact •! Relay 1/2 each 2-contact •! SENS-CHECK 2-contact •! RS-485 3-contact •! Recorder connections each 2-contact •! Sensor 7-contact 126 126 !"# $%&' !"# ()* Technical Data !"# $%&' !"# ()* Technical Data Protection type Protection type Lightning protector (inputs and outputs) •! Coarse protection 90 V / 1.5 KA (8/20µs) •! Fine protection 600 Watt Lightning protector (inputs and outputs) •! Coarse protection 90 V / 1.5 KA (8/20µs) •! Fine protection 600 Watt Electrical instrument protection Housing Safety class Electrical instrument protection Housing Safety class 2 according to IEC 1010 IP 54 2 according to IEC 1010 IP 54 Electrical connection data Electrical connection data •! 230 VAC (– 15% + 10%) Voltage supply (depending on the instrument •! 115 VAC (– 15% + 10%) •! 24 VAC (– 15% + 10%) version) •! 24 VDC (– 30% + 20%) Frequency 48 to 62 Hz Power consumption Max. 18 Watt Test certificates UL, cUL (for 115 VAC, 24 VAC and 24 VDC) CE (for all supply voltages) Interference suppression According to EN 50081-1 Interference immunity According to EN 50082-2, Namur recommendations •! 230 VAC (– 15% + 10%) Voltage supply (depending on the instrument •! 115 VAC (– 15% + 10%) •! 24 VAC (– 15% + 10%) version) •! 24 VDC (– 30% + 20%) Frequency 48 to 62 Hz Power consumption Max. 18 Watt Test certificates UL, cUL (for 115 VAC, 24 VAC and 24 VDC) GS, CE (for all supply voltages) Interference suppression According to EN 50081-1 Interference immunity According to EN 50082-2, Namur recommendations Ambient temperature Ambient temperature Limits of operating range Storage and transport temperature – 25 °C to + 55 °C – 25 °C to + 65 °C Limits of operating range Storage and transport temperature Mechanical data Dimensions Weight Keypad (material) Housing (material) – 25 °C to + 55 °C – 25 °C to + 65 °C Mechanical data 96 x 96 x 168 mm (B x H x T) Approx. 1.1 kg Polyester Fiber-reinforced Noryl Dimensions Weight Keypad (material) Housing (material) 127 96 x 96 x 168 mm (B x H x T) Approx. 1.1 kg Polyester Fiber-reinforced Noryl 127