Download FOS-500

SPARE PARTS LIST FOS-500
UK
REF NR
001
002
005
006
007
008
009
012
016
019
020
021
025
028
037
044
045
046
DESCRIPTION
PLASTIC PLATE
BASE PLATE
KNOB
LEVER FOR FIXING RING
NUT
COLLET 1/4”
COLLET 1/8”
BEARING
LOCKING PIN
ROTOR
BEARING (608 Z)
RUBBER BEARING HOLDER
STATOR
CARBON BRUSH SET
SWITCH
KNOB FOR HANDLE
HANDLE
WRENCH
FERM NR
408700
408701
408702
408703
408704
408705
408706
408707
408708
408709
800608
408710
408711
408712
408713
408714
408715
408716
SAFETY INSTRUCTIONS
English
The following symbols are used in these instructions for
use:
OMNISAW
THE NUMBERS IN THE FOLLOWING TEXT CORRESPOND WITH THE PICTURES AT PAGE 2
Denotes risk of electric shock.
TECHNICAL SPECIFICATIONS
Voltage
Frequency
Power input
Speed, no load
Nett weight
Lpa (sound pressure)
Lwa (sound power level)
Vibration value
|
|
|
|
|
|
|
|
230 V~
50 Hz
500 W
30000/min
1.51 kg
83.9 dB(A)
96.9 dB(A)
4.6 m/s2
DESCRIPTION
Fig.A
1. Base plate and depth guide
2. Collet nut
3. Spindle lock button
4. Exhaust air vents
5. Removable auxiliary handle
6. On/off slide switch
7. Intake air vents
8. Power supply cable
9. Depth guide bracket
10. Depth guide locking knob
11. Locking knob of depth guide bracket
12. Bit
13. Protection guide cap (not shown)
PACKAGE CONTENTS
1 Omnisaw
1 1/4" collet
1 1/4" Window/Door Bit (ZBWD8) for Plaster cutting
1/4"
1 1/8" Guidepoint Bit (GP10) for Drywall cutting 1/8"
1 1/8" Outlet Bit (ZB10) for Plaster cutting 1/8"
2 1/8" Sabrecut Bit (ZBSC5) for Wood/Plastic cutting
1/8"
1 1/8" Tilecut Bit (RZ125) for Ceramic cutting 1/8"
1 Wrench
1 Protection guide cap
1 Carrying case
Check the machine, loose parts and accessories for
transport damage.
66
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Ferm
Ferm
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
BEFORE USING THE OMNISAW
• Check the voltage of the motor and the motor overload (if any) correspond:
Do the voltage of the engine and the engine safeguard, if any, correspond to the mains voltage
(appliances for a mains voltage of 230 V).
Are the mains lead and the mains plug in a good condition: solid, without any loose ends or damage.
• Remove adjusting keys or wrenches before turning
the tool on.
• Always wear eye protection when using the tool.
• Maintain the tool with care.
• Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tools operation. If damaged, have the tool
serviced before using.
• Use only accessories that are recommended by the
manufacturer for your model.
• Compare the maximum number of revolutions allowed of the accessories with the number of revolutions of the machine.
• Make sure that the spring chuck diameter is the same
as the axle diameter of the accessory.
• The flutes of the bits (cutting edges and top) are very
sharp. Therefore, handle with caution.
USING THE MACHINE
• Use clamps or a vice to hold the work.
• Do not use the tool if the switch does not turn it
"ON" or "OFF".
• Always hold the tool with two hands while starting.
• Hold the tool by the insulated gripping surfaces when
performing an operation where the bit may contact
hidden wiring. If cutting into existing walls or other
blind areas is unavoidable, disconnect all fuses or circuit breakers to the worksite.
• Always keep the cord away from the moving parts of
the machine.
3