Download LED's light

LED‘s light
Installation and Operating Manual
1.
2.
Specifications
Art Nr.
Power
Input voltage
LED Lumen output
Color temp.
2400001/2400002
6W
220-240V AC
480
6500K
2400003
6W
220-240V AC
480
6500K
2400013/2400014
Max 60W / E27
220-240V AC
-
Motion detector
PIR + Day/Night
Day/Night
PIR + Day/Night
Up to 12 m
20.000 hours
IP44
280 x 113 x 112mm
20.000 hours
IP44
266 x 113 x 112mm
Up to 12 m
Depends on lamp
IP44
280 x 113 x 112mm
Angle of coverage
Lifespan
Degree of protection
Dimensions
3.
4.
5.
6.
7.
General safety instructions
Please read the operating instructions for the
LED lamp before use. The operating instructions
are part of the product. They contain important
notes on start-up and handling of the device. Always keep the enclosed operating instructions so
as to be able to look up information. They must
be enclosed when passing the device on to third
parties.
Safety precautions
The user must observe the safety notes and
warnings in order to maintain this status and to
ensure safe operation. Please read the operating
instructions before start up.
Never attempt to open the device other than described in this manual. The LED lamp cannot be
repaired; this part must be immediately disposed
in case of a defect. Ensure sufficient ventilation
of the device. Never cover it during operation. Do
not install in reach of children or animals.
Any other use of the device than described above
can damage the product or endanger the user
due to e. g. short-circuits, fire or an electric
shock. The entire product may not be modified
or adapted. Don’t touch the lamp while in use or
after use until it’s cooled down. The lamp must
have an earthed connection for safe operation.
These safety notes must be observed in all cases! Any warranty claim is void in the case of
damages caused by non-observance of these
operating instructions. We are not liable for
consequential damages or for damages to property or persons caused by non-observance of
the safety notes and improper operation of the
device.
Installation instructions
•
•
•
•
Mount the luminaire 1.8 to 2.5 meters above
the area to be scanned (refer Fig.1A).
To avoid damage to the unit; do not aim the
sensor towards the sun.
The sensor should be directed away from
heat sources such as barbecues, Air-conditioners, other outside lighting, moving cars
and flue vents. This can cause unwanted reactions of the sensor of the luminaire.
Do not aim towards reflective surfaces such
as smooth white walls, swimming pools,
etc. The PIR Sensor scanning specifications (approximately 12 meters at approx.
110°--horizontal) may vary slightly depending on the mounting height and location.
The detection range of the unit may also be
different with temperature change. Before
selecting a place to install your global lamp
you should note that movement across the
scan area is more effective than movement
directly toward or away from the sensor (refer Fig.1B). If movement is made walking
directly towards or away from the sensor
and not across, the apparent detection range will be substantially reduced. (refer Fig.
1C) The sensor can be adjusted to have change the detection area by turning it to the
right or left.
Note:
Installation must be done by an electrician who
knows the regulations.
Ensure that the main power is turned off
before mounting the luminaire.
Remove the Lampshade by Screwdriver,
see figure 3.
Mark the mounting hole positions onto the
wall. Drill and plug the wall at the marked
positions. Screw the lamp body to wall with
suitable Mounting Screws (supplied)
Unscrew the Screw (A) and remove the
Transparent Plate.
Connecting the main power wires(H05RN-F
3G 1.0mm²) to the Terminal Block (see the
relative symbols—Fig.3), the Cable must
pass through the Wiring Rubber Gasket.
Re-screw Transparent Plate and Re-fit the
Lampshade by hand.
After finish the mounting, you can adjust
the detection area and working state of PIR
Sensor/for 2400003 the day/night sensor by
using a hand.
Note:
• The Bulkhead Light should be wired to its
own lamp switch. Do not interconnect with
other lights on the same switch.
• Do not connect to Dimmer.
appro.110°
2.5 Meters
4M
8M
12M
Fig. 1 (A) Detection area
2.
3.
4.
5.
a minute for the control circuit to stabilize.
At this stage ensure that the TIME control
knob is set at minimum duration time (-)
position. The bulkhead light will now switch
on and remain on for about 30 seconds (within 60 seconds).
Direct the sensor toward the desired area to
be scanned by turning the PIR sensor.
Another person has to cross the center of
the area to be scanned and slowly adjust
the PIR sensor until the unit reacts on the
presence of the moving person, causing the
lamp to switch on. (refer Fig. 1B).
Adjust time control to required setting.
To set the lux level at which the lamp will
automatically switch “on” at night, please
turn the LUX control knob from daylight to
night. If the lamp is required to switch on
earlier, e. g. Dusk, wait for the desired environment light level, then slowly turn the
LUX control knob towards the daylight (☼)
while someone walks across the center
of the area to be detected. When the lamp
switches on, release the LUX control knob.
Operating instructions
ADJUSTING DURATION TIME: The length of time
that remains switched on after activation can be
adjusted from (10±5) seconds to (4±1) minutes.
Rotating the TIME knob from (+) to (-) will reduce
the duration time.
Note: If the light has been triggered again by the
PIR sensor, the timed period starts again from
the beginning.
ADJUSTING THE LUX CONTROL LEVEL: The Lux
control module has a built-in sensing device
(photocell) that detects daylight and darkness.
The (☼) position denotes that the luminaire can
work at day and night, and the (☽) position only
work at night. You can set to operate the unit at
the desired level by adjusting the LUX knob.
Setting the controls
1. Put the Lux control knob to light (☼) position, turn the wall switch on and wait half
For further Installation of the luminaire, please
referring to the Fig.3, (note: the non-LED version
has an E27 socket inside).
Lampshade
Mounting Screws
Safe operation is not possible anymore, if:
-the LED lamp has visible damages,
-the LED lamp does not work anymore
LED
Fig. 1(B) GOOD
Notes on Disposal
Old units, marked with the symbol as illustrated, may not be disposed of in the
household rubbish.
You must take them to a collection point
for old units (enquire at your local authority) or
the dealer from whom you bought them. These
agencies will ensure environmentally friendly
disposal.
Terminal Block
Care and warranty
Before cleaning the unit, disconnect it if necessary from other components; do not use aggressive cleaning agents.
The unit has been carefully checked for defects.
If nevertheless you do have cause for complaint,
please go back to the retailer where you have
bought the product together with your proof of
purchase. We offer a 2year warranty from date
of purchase. We are not liable for damage arising
from incorrect handling, improper use or wear
and tear. We reserve the right to make technical
modifications.
Visit us online at www.shada.nl for more information about our products and our company.
Fig. 1(C) NOT GOOD
Screwdriver
CE declaration
This product is according next directives
LVD 2006/95/EG, EMC 2004/108/EG
RoHS 2002/95/EG.
LN
Imported by
Kanaal Noord 350
NL-7323 AM Apeldoorn
www.shada.nl
WEEE DE: 97413743
WEEE NL: 3505
WEEE AT: 40133
Screw (A)
Transparent Plate
Fig.3 Mounting and Wiring to Terminal
2400003