Download Hameg HM8135 / HM8135X | RF-Synthesizer Benutzerhandbuch
Transcript
3 GHz RF-Synthesizer HM8135, HM8135-X Ihr Spezialist für Mess- und Prüfgeräte Handbuch / Manual Deutsch / English Optional HO880 IEEE-488 (GPIB) Schnittstelle R Frequenzbereich: 1Hz bis 3GHz R Hoher dynamischer Ausgangspegel: -135dBm bis +13dBm R Frequenzauflösung: 1Hz R Hohe spektrale Reinheit, exzellente SWEEP Funktion R Modulationsarten: AM, FM, Puls, Phase, FSK, PSK Wahl der Modulationsart R Interne Modulation (10Hz bis 200kHz): Benutzerhandbuch / User Manual HM8135 3 GHz RF-Synthesizer HM8135, HM8135X 3GHz HF-Synthesizer Benutzerhandbuch HM8135 | HM8135-X User Manual Sinus, Rechteck, Dreieck, Rampe R Externer Ref.-Eingang/Ausgang (10MHz) über BNC-Anschluss Distributed by: R HM8135: TCXO (Temperaturstabilität: ±0,5 x 10-6) HM8135-X: OCXO (Temperaturstabilität: ±1,0 x 10-8) dataTec ▪ Ferdinand-Lassalle-Str. 52 ▪ 72770 Reutlingen ▪ Tel. 07121 / 51 50 50 ▪ Fax 07121 / 51 50 10 ▪ [email protected] ▪ www.datatec.de KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY DECLARATION DE CONFORMITE Hersteller / Manufacturer / Fabricant / Fabricante: HAMEG Instruments GmbH · Industriestraße 6 · D-63533 Mainhausen Die HAMEG Instruments GmbH bescheinigt die Konformität für das Produkt The HAMEG Instruments GmbH herewith declares conformity of the product HAMEG Instruments GmbH déclare la conformite du produit Bezeichnung: HF-Synthesizer Product name: RF-Synthesizer Designation:HF-Synthesizer Typ / Type / Type: HM8135, HM8135X mit / with / avec: HO820 Optionen / Options / Options: HO880 mit den folgenden Bestimmungen / with applicable regulations / avec les directives suivantes: EMV Richtlinie: 2004/108/EG EMC Directive: 2004/108/EG Directive CEM: 2004/108/EG Niederspannungsrichtlinie: 2006/95/EG Low-Voltage Equipment Directive: 2006/95/EG Directive des equipements basse tension: 2006/95/EG Angewendete harmonisierte Normen / Harmonized standards applied / Normes harmonisées utilisées: Sicherheit / Safety / Sécurité: EN 61010-1 (07/2011) Elektromagnetische Verträglichkeit / Electromagnetic compatibility / Compatibilité électromagnétique: EMV Störaussendung / EMI Radiation / Emission CEM: EN 61326-1 (10/20116) IEC/CISPR 11 ( 2009, modifiziert + A1:2010), DIN VDE 0876 (10/2007), DIN VDE 0877 (08/2007) Störfestigkeit / Immunity / Imunitee: EN 61326-1 (10/20116)1 EN 61000-4-2 (12/2009), EN 61000-4-3 (04/2011), EN 61000-4-4 (11/2010), EN 61000-4-5 (06/2007), EN 61000-4-6 (12/2009), EN 61000-4-8 (11/2010), EN 61000-4-11 (02/2005) Datum / Date / Date 21. 06. 2012 2 Unterschrift / Signature / Signatur / Signatura Holger Asmussen General Manager Allgemeine Hinweise zur CE-Kennzeichnung HAMEG Messgeräte erfüllen die Bestimmungen der EMV Richtlinie. Bei der Konformitätsprüfung werden von HAMEG die gültigen Fachgrund- bzw. Produktnormen zu Grunde gelegt. In Fällen, wo unterschiedliche Grenzwerte möglich sind, werden von HAMEG die härteren Prüfbedingungen angewendet. Für die Störaussendung werden die Grenzwerte für den Geschäfts- und Gewerbebereich sowie für Kleinbetriebe angewandt (Klasse 1B). Bezüglich der Störfestigkeit finden die für den Industriebereich geltenden Grenzwerte Anwendung. Die am Messgerät notwendigerweise angeschlossenen Mess- und Datenleitungen beeinflussen die Einhaltung der vorgegebenen Grenzwerte in erheblicher Weise. Die verwendeten Leitungen sind jedoch je nach Anwendungsbereich unterschiedlich. Im praktischen Messbetrieb sind daher in Bezug auf Störaussendung bzw. Störfestigkeit folgende Hinweise und Randbedingungen unbedingt zu beachten: 1. Datenleitungen Die Verbindung von Messgeräten bzw. ihren Schnittstellen mit externen Geräten (Druckern, Rechnern, etc.) darf nur mit ausreichend abgeschirmten Leitungen erfolgen. Sofern die Bedienungsanleitung nicht eine geringere maximale Leitungslänge vorschreibt, dürfen Datenleitungen (Eingang/Ausgang, Signal/Steuerung) eine Länge von 3 Metern nicht erreichen und sich nicht außerhalb von Gebäuden befinden. Ist an einem Geräteinterface der Anschluss mehrerer Schnittstellenkabel möglich, so darf jeweils nur eines angeschlossen sein. Bei Datenleitungen ist generell auf doppelt abgeschirmtes Verbindungskabel zu achten. Als IEEE-Bus Kabel ist das von HAMEG beziehbare doppelt geschirmte Kabel HZ72 geeignet. 2. Signalleitungen Messleitungen zur Signalübertragung zwischen Messstelle und Messgerät sollten generell so kurz wie möglich gehalten werden. Falls keine geringere Länge vorgeschrieben ist, dürfen Signalleitungen (Eingang/Ausgang, Signal/Steuerung) eine Länge von 3 Metern nicht erreichen und sich nicht außerhalb von Gebäuden befinden. Alle Signalleitungen sind grundsätzlich als abgeschirmte Leitungen (Koaxialkabel - RG58/U) zu verwenden. Für eine korrekte Massever-bindung muss Sorge getragen werden. Bei Signalgeneratoren müssen doppelt abgeschirmte Koaxialkabel (RG223/U, RG214/U) verwendet werden. 3. Auswirkungen auf die Geräte Beim Vorliegen starker hochfrequenter elektrischer oder magnetischer Felder kann es trotz sorgfältigen Messaufbaues über die angeschlossenen Kabel und Leitungen zu Einspeisung unerwünschter Signalanteile in das Gerät kommen. Dies führt bei HAMEG Geräten nicht zu einer Zerstörung oder Außerbetriebsetzung. Geringfügige Abweichungen der Anzeige – und Messwerte über die vorgegebenen Spezifikationen hinaus können durch die äußeren Umstände in Einzelfällen jedoch auftreten. HAMEG Instruments GmbH Inhalt Inhalt Allgemeine Hinweise zur CE-Kennzeichnung. . . . . . . 2 1 Wichtige Hinweise. . . . . . . . . . . . . . . . . . . . . . . 4 1.1Symbole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2Auspacken . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 Aufstellen des Gerätes. . . . . . . . . . . . . . . . . . . . . . . . 4 1.4 Transport und Lagerung. . . . . . . . . . . . . . . . . . . . . . . 4 1.5Sicherheitshinweise. . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.6 Bestimmungsgemäßer Betrieb . . . . . . . . . . . . . . . . . 4 1.7 Gewährleistung und Reparatur . . . . . . . . . . . . . . . . . 5 1.8Wartung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.9Netzspannungsumschaltung. . . . . . . . . . . . . . . . . . . 5 1.10Sicherungswechsel . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Bezeichnung der Bedienelemente. . . . . . . . . . . 6 3 Die Bedienung des HM8135. . . . . . . . . . . . . . . . 7 3.1Inbetriebnahme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.2Einschalten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.3Werkseinstellung . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.4Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.5ESC-Taste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.6 Einstellung der Parameter . . . . . . . . . . . . . . . . . . . . . 7 3.7 Wahl der Frequenz. . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.8 Wahl des Pegels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.9 Wahl der Modulationsart. . . . . . . . . . . . . . . . . . . . . . 8 4Modulationsarten. . . . . . . . . . . . . . . . . . . . . . . 10 4.1 Amplitudenmodulation (AM). . . . . . . . . . . . . . . . . . 10 4.2 Frequenzmodulation (FM) . . . . . . . . . . . . . . . . . . . . 10 4.3 Phasenmodulation (PM). . . . . . . . . . . . . . . . . . . . . . 11 4.4 FSK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.5 PSK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.6GATE-Modulation. . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 Einstellen derGerätekonfiguration. . . . . . . . . . 13 5.1Schrittauswahl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.2MENU-Taste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.3 Offset Korrektur . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.4 Referenz REF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.5 Spezialfunktionen SfC. . . . . . . . . . . . . . . . . . . . . . . . 14 5.6 Beeper BeeP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.7 Drehgeber Enco (Encoder). . . . . . . . . . . . . . . . . . . . 15 5.8 Interface COM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.9 Display LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.10SWEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.11Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.12Trig: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.13 PREV. Taste (Previous) . . . . . . . . . . . . . . . . . . . . . . . 16 5.14ON-Taste. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.15 RCL-STO Tasten (Recall & Store). . . . . . . . . . . . . . . . 16 6Fernbedienung. . . . . . . . . . . . . . . . . . . . . . . . . 17 6.1Schnittstellen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.2 Nachrüstung einer Schnittstelle. . . . . . . . . . . . . . . . 17 6.3 Unterstützte Befehle. . . . . . . . . . . . . . . . . . . . . . . . . 17 6.4 Beschreibung der Befehle . . . . . . . . . . . . . . . . . . . . 18 6.5 Generelle Befehle. . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.6 Bus Befehle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.7 Sound Befehle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.8 Befehle OUTPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.9 Befehle POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.10 Befehle FREQUENCY. . . . . . . . . . . . . . . . . . . . . . . . 18 6.11 Befehle PHASE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.12 Befehle PULM (PULse Modulation / Gate). . . . . . . . 19 6.13 Befehle AM (Amplituden-Modulation). . . . . . . . . . . 19 6.14 Befehle FM (Frequenz-Modulation). . . . . . . . . . . . . 20 6.15 Befehle PM (Phasen-Modulation). . . . . . . . . . . . . . . 20 6.16 Befehle FSK (FSK Modulation). . . . . . . . . . . . . . . . . 21 6.17 Befehle PSK (PSK Modulation). . . . . . . . . . . . . . . . . 21 6.18 Befehle SWEEP (SWEEP Funktion). . . . . . . . . . . . . 22 6.19 Befehle SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.20 Bedeutung des Fehlercodes. . . . . . . . . . . . . . . . . . . 23 7 Technische Daten. . . . . . . . . . . . . . . . . . . . . . . 24 Flussdiagramme (Flow Charts). . . . . . . . . . . . . 50 Umrechnungstabellen . . . . . . . . . . . . . . . . . . . 59 3 Wichtige Hinweise 1 Wichtige Hinweise 1.1Symbole ! (1) Symbol 1: Symbol 2: Symbol 3: Symbol 4: (2) (3) (4) Achtung - Bedienungsanleitung beachten Vorsicht Hochspannung Masseanschluss Stop! – Gefahr für das Gerät 1.2Auspacken Prüfen Sie beim Auspacken den Packungsinhalt auf Vollständigkeit. Ist der Netzspannungsumschalter entsprechend der vorhandenen Netzversorgung eingestellt? Nach dem Auspacken sollte das Gerät auf mechanische Beschädigungen und lose Teile im Innern überprüft werden. Falls ein Transportschaden vorliegt, ist sofort der Lieferant zu informieren. Das Gerät darf dann nicht in Betrieb genommen werden. 1.3 Aufstellen des Gerätes Das Gerät kann in zwei verschiedenen Positionen aufgestellt werden: Die vorderen Gerätefüße können ausgeAbb. 1 Abb. 2 Abb. 3 klappt werden (Abb. 1). Die Gerätefront zeigt dann leicht nach oben (Neigung etwa 10°). Bleiben die vorderen Gerätefüße eingeklappt (Abb. 2), lässt sich das Gerät mit weiteren HAMEG-Geräten sicher stapeln. Werden mehrere Geräte aufeinander gestellt, sitzen die eingeklappten Gerätefüße in den Arretierungen des darunter liegenden Gerätes und sind gegen unbeabsichtigtes Verrutschen gesichert (Abb. 3). Es sollte darauf geachtet werden, dass nicht mehr als drei Messgeräte übereinander gestapelt werden, da ein zu hoher Geräteturm instabil werden kann. Ebenso kann die Wärmeentwicklung bei gleichzeitigem Betrieb aller Geräte dadurch zu groß werden. 4 1.4 Transport und Lagerung Bewahren Sie bitte den Originalkarton für einen eventuellen späteren Transport auf. Transportschäden aufgrund einer mangelhaften Verpackung sind von der Gewährleistung ausgeschlossen. Die Lagerung des Gerätes muss in trockenen, geschlossenen Räumen erfolgen. Wurde das Gerät bei extremen Temperaturen transportiert, sollte vor der Inbetriebnahme eine Zeit von mindestens 2 Stunden für die Akklimatisierung des Gerätes eingehalten werden. 1.5Sicherheitshinweise Dieses Gerät wurde gemäß VDE0411 Teil1, Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel, und Laborgeräte, gebaut und geprüft und hat das Werk in sicherheitstechnisch einwandfreiem Zustand verlassen. Es entspricht damit auch den Bestimmungen der europäischen Norm EN 61010-1 bzw. der internationalen Norm IEC 610101. Um diesen Zustand zu erhalten und einen gefahrlosen Betrieb sicherzustellen, muss der Anwender die Hinweise und Warnvermerke in dieser Bedienungsanleitung beachten. Den Bestimmungen der Schutzklasse 1 entsprechend sind alle Gehäuse- und Chassisteile während des Betriebs mit dem Netzschutzleiter verbunden. Sind Zweifel an der Funktion oder Sicherheit der Netzsteckdosen aufgetreten, so sind die Steckdosen nach DIN VDE0100, Teil 610, zu prüfen. ❙❙ Die verfügbare Netzspannung muss den auf dem Typenschild des Gerätes angegebenen Werten entsprechen. ❙❙ Das Öffnen des Gerätes darf nur von einer entsprechend ausgebildeten Fachkraft erfolgen. ❙❙ Vor dem Öffnen muss das Gerät ausgeschaltet und von allen Stromkreisen getrennt sein. Das Auftrennen der Schutzkontaktverbindung innerhalb oder außerhalb des Gerätes ist unzulässig! In folgenden Fällen ist das Gerät außer Betrieb zu setzen und gegen unabsichtlichen Betrieb zu sichern: ❙❙ sichtbare Beschädigungen am Gerät ❙❙ Beschädigungen an der Anschlussleitung ❙❙ Beschädigungen am Sicherungshalter ❙❙ lose Teile im Gerät ❙❙ das Gerät funktioniert nicht mehr ❙❙ nach längerer Lagerung unter ungünstigen Verhältnissen (z.B. im Freien oder in feuchten Räumen) ❙❙ schwere Transportbeanspruchung. 1.6 Bestimmungsgemäßer Betrieb Die Geräte sind zum Gebrauch in sauberen, trockenen Räumen bestimmt. Sie dürfen nicht bei besonders großem Staub- bzw. Feuchtigkeitsgehalt der Luft, bei Explosionsgefahr sowie bei aggressiver chemischer Einwirkung betrieben werden. Die zulässige Umgebungstemperatur während des Betriebes reicht von +5 °C bis +40 °C. Während der Lagerung oder des Transportes darf die Temperatur zwischen –20 °C Wichtige Hinweise und +70 °C betragen. Hat sich während des Transportes oder der Lagerung Kondenswasser gebildet, muss das Gerät ca. 2 Stunden akklimatisiert werden, bevor es in Betrieb genommen wird. Das Gerät darf aus Sicherheitsgründen nur an vorschriftsmäßigen Schutzkontaktsteckdosen oder an Schutz-Trenntransformatoren der Schutzklasse 2 betrieben werden. Die Betriebslage ist beliebig. Eine ausreichende Luftzirkulation (Konvektionskühlung) ist jedoch zu gewährleisten. Bei Dauerbetrieb ist folglich eine horizontale oder schräge Betriebslage (vordere Gerätefüße aufgeklappt) zu bevorzugen. Die Lüftungslöcher und die Kühlkörper des Gerätes dürfen nicht abgedeckt werden ! Nenndaten mit Toleranzangaben gelten nach einer Anwärmzeit von min. 30 Minuten, bei einer Umgebungstemperatur von 23 °C. Werte ohne Toleranzangabe sind Richtwerte eines durchschnittlichen Gerätes. 1.7 Gewährleistung und Reparatur HAMEG-Geräte unterliegen einer strengen Qualitätskontrolle. Jedes Gerät durchläuft vor dem Verlassen der Produktion einen 10-stündigen „Burn in-Test“. Im intermittierenden Betrieb wird dabei fast jeder Frühausfall erkannt. Anschließend erfolgt ein umfangreicher Funktions- und Qualitätstest, bei dem alle Betriebsarten und die Einhaltung der technischen Daten geprüft werden. Die Prüfung erfolgt mit Prüfmitteln, die auf nationale Normale rückführbar kalibriert sind. Es gelten die gesetzlichen Gewährleistungsbestimmungen des Landes, in dem das HAMEGProdukt erworben wurde. Bei Beanstandungen wenden Sie sich bitte an den Händler, bei dem Sie das HAMEGProdukt erworben haben. Nur für die Länder der EU: Sollte dennoch eine Reparatur Ihres Gerätes erforderlich sein, können Kunden innerhalb der EU die Reparaturen auch direkt mit HAMEG abwickeln, um den Ablauf zu beschleunigen. Auch nach Ablauf der Gewährleistungsfrist steht Ihnen der HAMEG Kundenservice (siehe RMA) für Reparaturen zur Verfügung. Return Material Authorization (RMA): Bevor Sie ein Gerät an uns zurücksenden, fordern Sie bitte in jedem Fall per Internet: http://www.hameg.com oder Fax eine RMA-Nummer an. Sollte Ihnen keine geeignete Verpackung zur Verfügung stehen, so können Sie einen leeren Originalkarton über den HAMEG-Service (Tel: +49 (0) 6182 800 500, Fax: +49 (0) 6182 800 501, E-Mail: [email protected]) bestellen. 1.8Wartung Die Anzeige darf nur mit Wasser oder geeignetem Glasreiniger (aber nicht mit Alkohol oder Lösungsmitteln) gesäubert werden, sie ist dann noch mit einem trockenen, sauberen, fusselfreien Tuch nachzureiben. Keinesfalls darf die Reinigungsflüssigkeit in das Gerät gelangen. Die Anwendung anderer Reinigungsmittel kann die Beschriftung oder Kunststoff- und Lackoberflächen angreifen. 1.9Netzspannungsumschaltung Das Gerät arbeitet mit einer Netzwechselspannung von 115 V oder 230 V 50/60 Hz. Die vorhandene Netzversorgungsspannung wird mit dem Netzspannungsumschalter eingestellt. Mit der Netzspannungsumschaltung ist ein Wechsel der Netzeingangssicherungen notwendig. 1.10Sicherungswechsel Die Netzeingangssicherungen sind von außen zugänglich. Kaltgeräteeinbaustecker und Sicherungshalter bilden eine Einheit. Das Auswechseln der Sicherung darf nur erfolgen wenn zuvor das Gerät vom Netz getrennt und das Netzkabel abgezogen wurde. Sicherungshalter und Netzkabel müssen unbeschädigt sein. Mit einem geeigneten Schraubenzieher (Klingenbreite ca. 2mm) werden die an der linken und rechten Seite des Sicherungshalters befindlichen Kunststoffarretierungen nach innen gedrückt. Der Ansatzpunkt ist am Gehäuse mit zwei schrägen Führungen markiert. Beim Entriegeln wird der Sicherungshalter durch Druckfedern nach außen gedrückt und kann entnommen werden. Die Sicherungen sind dann zugänglich und können ggf. ersetzt werden. Es ist darauf zu achten, dass die zur Seite herausstehenden Kontaktfedern nicht verbogen werden. Das Einsetzen des Sicherungshalters ist nur möglich, wenn der Führungssteg zur Buchse zeigt. Der Sicherungshalter wird gegen den Federdruck eingeschoben, bis beide Kunststoffarretierungen einrasten. Ein Reparieren der defekten Sicherung oder das Verwenden anderer Hilfsmittel zum Überbrücken der Sicherung ist gefährlich und unzulässig. Dadurch entstandene Schäden am Gerät fallen nicht unter die Gewährleistung. Sicherungstype: Größe 5 x 20 mm; 250V~, C; IEC 127, Bl. III; DIN 41 662 (evtl. DIN 41 571, Bl. 3). Netzspannung 230 V 115 V Sicherungs-Nennstrom T0,5 A T1,0 A ❙❙ Die Außenseite des Gerätes sollte regelmäßig mit einem weichen, nicht fasernden Staubtuch gereinigt werden. ❙❙ Bevor Sie das Gerät reinigen stellen Sie sicher, dass es ausgeschaltet und von allen Spannungsversorgungen getrennt ist. ❙❙ Keine Teile des Gerätes dürfen mit Alkohol oder anderen Lösungsmitteln gereinigt werden! 5 Bezeichnung der Bedienelemente 2 Bezeichnung der Bedienelemente 9 FUNCTIONS: Funktionstasten und LEDs 10 Einstellknopf (digitaler Drehgeber): Zur Einstellung sämtlicher Betriebsparameter 11 NUMERISCHE TASTATUR: Eingabeparameter mit Maßeinheit 12 ON: Taste zur Aktivierung des Ausgangs Geräte-Vorderseite 12 ESC (Escape): Taste zum Rücksprung ins Hauptmenü 1 POWER (Netzspannung): Netzschalter mit LED 14 RF OUTPUT 50 Ω (Radio Frequency Output): Generatorsignalausgang 2 MOD. INPUT (Modulation Input): Externer Modulationseingang 15 MOD. OUTPUT (Modulation Output): 3 PREV. (Previous): Taste zur Auswahl des vorherigen Menüs Modulationssignalausgang Geräte-Rückseite 4 MEMORY RCL (Memory Recall): Taste zum Aufruf von bis zu 10 gespeicherten Instrumenten-Einstellungen 5 CONTEXT SENSITIVE KEYS: Die jeweilige Funktion der kontextsensitiven Tasten entspricht der Display-Anzeige 6 MEMORY STO (Memory Store): Taste zur Abspeiche- rung von bis zu 10 Instrumenteneinstellungen 16 Kaltgeräteeinbaustecker 17 VOLTAGE SELECTOR: Netzspannungswahlschalter 18 F1 (FUSE): Sicherung 19 GATE INPUT: GATE-Eingang,TTL-kompatibel 20 REF. OUTPUT 10 MHz: Referenzsignalausgang 7 MENU: Taste zum Aufruf des Konfigurations-Menüs 21 REF. INPUT 10 MHz: Referenzsignaleingang 8 DISPLAY: Alphanumerische Anzeige, bestehend aus 22 RS-232 Schnittstelle zwei Zeilen mit jeweils 20 Zeichen. Hintergrundbeleuchtete LCD 23 USB/RS-232 Schnittstelle (HO820) optional: IEEE-488 GPIB (HO880) 8 2 3 4 5 6 10 7 9 11 13 1 12 14 Abb. 2.1: Frontansicht des HM8135 23 16 Abb. 2.2: Rückansicht des HM8135 6 18 17 22 21 20 19 15 Die Bedienung des HM8135 3 Die Bedienung des HM8135 3.1Inbetriebnahme Beachten Sie bitte besonders bei der ersten Inbetriebnahme des Gerätes folgende Punkte: ❙❙ Die verfügbare Netzspannung muss mit dem auf der Geräterückseite (Netzspannungswahlschalter) angegebenen Wert übereinstimmen. ❙❙ Vorschriftsmäßiger Anschluss an Schutzkontaktsteckdose oder Schutz-Trenntransformatoren der Schutzklasse 2 ❙❙ Keine sichtbaren Beschädigungen am Gerät ❙❙ Keine Beschädigungen an der Anschlussleitung ❙❙ Keine losen Teile im Gerät 3.2Einschalten Nach Betätigung des roten Netzschalters 1 erscheinen auf dem Display des HM8135 die folgenden Nachrichten: ❙❙ der Gerätetyp (SYNTHESIZER) und die Versionsbezeichnung (HM8135) ❙❙ eine Selbsttestnachricht „RAM checking“ und „DDS loading“ (RAM = Random Access Memory, DDS = Direct Digital Synthesis) ❙❙ Optionales Interface: Second Com Interface: NONE, USB/RS-232 (HO820), IEEE488 (HO880)) ❙❙ Optionaler OCXO: FREQUENCY REFERENCE ❙❙ OCXO OPTION > NO (YES) ❙❙ die aktuelle Referenzquelle (intern oder extern): FREQUENCY REFERENCE Internal (External) Beim Einschalten lädt das Gerät automatisch die Einstellungen, die im Konfigurationsspeicher O abgelegt sind. Das Ausgangssignal ist standardmäßig bei Betriebsbeginn immer abgeschaltet. 3.3Werkseinstellung ❙❙ Frequenz: 3000 MHz ❙❙ Pegel: +7 dBm ❙❙ Keine Modulationsart ❙❙ Interne Referenzfrequenz ❙❙ Fmod: 1 kHz, Form: Sinus (für alle Modulationsarten) ❙❙ Dev: 20 kHz (FM), Dev: 1 rad (PM) , Modulationsgrad: 50% (AM) ❙❙ Hintergrundbeleuchtung: mittel ❙❙ Kontrast: maximal ❙❙ Sound Indikator: Aus ❙❙ Drehgeber: Ein ❙❙ Schnittstellenparameter: 4800 Baud / 1 Stopbit / 8 Datenbits Die Basiseinstellungen können jederzeit wie folgt aufgerufen werden: ❙❙ Gerät ausschalten. ❙❙ Gerät einschalten und solange die ESC-Taste drücken bis einige Beeps zu hören sind. Im Zweifelsfalle ist das eine hilfreiche Überwachungsfunktion. Achtung! Alle 10 Speicherplätze werden gelöscht und durch die vorherige Grundeinstellung ersetzt. 3.4Display Die Anzeige zeigt die Frequenz und den Pegelwert des RFAusgangssignals, sowie die verwendete Referenz (INTern oder EXTern). Wenn keine Modulationsart eingeschaltet ist, zeigt das Display: Im Falle der Amplitudenmodulation werden die Parameter Signalform (SQR = square wave) und Modulationsfrequenz (Fmod = 1 kHz) angezeigt. Zum Verlassen dieser Anzeige wird entweder eine Funktionstaste 9 oder die MenU-Taste 7 betätigt. 3.5ESC-Taste Mit der ESC-Taste erfolgt ein Aufruf des Haupt-Displays, sowie die Aufhebung der aktuellen Funktionsauswahl 9 oder das Löschen der numerischen Eingabe. 3.6 Einstellung der Parameter Nachdem ein Parameter mit einer Funktionstaste ausgewählt wurde (z. B. FREQ.), kann ein neuer Parameterwert mittels der numerischen Tastatur 11 eingegeben, mit dem digitalen Drehknopf 10 oder mit einer der vier kontextsensitiven Tasten 5 unterhalb des angezeigten Vorzeichens (+/–) verändert werden. Nach Werteingabe mit der numerischen Tastatur ist die Einheit auszuwählen (z. B. MHz oder dBm). Erst dann ist der Wert wirksam. Noch bevor die Einheit gewählt wird, kann der eingegebene Wert mit der ESC-Taste 13 annulliert werden und der vorherige Wert wird angezeigt. Bei der Eingabe sind Nullen vor der Kommastelle nicht erforderlich. Es wird jedoch immer eine Stelle links vom Komma angezeigt. Der Cursor kann durch die kontextsensitiven Tasten 5 unterhalb der Richtungspfeile in beide Richtungen entlang der Anzeige bewegt werden, um bei Betätigung der verschiedenen Eingabearten einen anderen Wert zu erzielen. 7 Die Bedienung des HM8135 Die Werterhöhung oder Wertminderung erfolgt mit dem Drehknopf 10 . Wird eine Leerstelle unterstrichen, gilt diese Stelle als Null und kann mit jedem Wert belegt werden. Eine falsche Eingabe wird mit einer Nachricht und einem akustischen Warnsignal quittiert, falls diese Funktion aktiviert ist. Dies trifft nicht bei Bereichsüberschreitung des Drehknopfes und Einzelschritten zu. 3.7 Wahl der Frequenz Nach Betätigung der FREQ.-Funktionstaste 9 zeigt das Display: Die Modulationsart wird nun mit den kontextsensitiven Tasten 5 ausgewählt: ❙❙ AM (Amplituden-Modulation) ❙❙ FM (Frequenz-Modulation) ❙❙ PM (Phasen-Modulation) ❙❙ FSK (Frequency Shift Keying-Modulation) ❙❙ PSK (Phase Shift Keying-Modulation) ❙❙ GATE (Gate-Modulation) Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Nach der Modulationswahl (FM Menü) zeigt das Display: Ein neuer Funktionswert kann über die Tastatur 11 , mit dem Drehknopf 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Die Bedienung erfolgt wie im Abschnitt „Einstellung der Parameter“ beschrieben. Der einstellbare Frequenzbereich liegt zwischen 1 Hz und 3000 MHz. Die Auflösung beträgt 1 Hz. Bei Eingabe von <1 Hz wird automatisch auf 1 Hz aufgerundet. 3.8 Wahl des Pegels Nach Betätigung der LEVEL-Funktionstaste 9 zeigt das Display: Die Parameterauswahl für die Funktionen AM/FM/PM erfolgt erneut über die kontextsensitiven Tasten: ❙❙ Form des internen Modulationssignals ❙❙ Frequenz des internen Modulationssignals ❙❙ Frequenzhub (oder Modulationsgrad in AM) ❙❙ Status der Modulation Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Nach Auswahl der Option Shape (AM SHAPE MENU) zeigt das Display: Ein neuer Funktionswert kann über die Tastatur 11 , mit dem Drehgeber 10 oder mit den kontextsensitiven Tasten eingestellt werden. Die Bedienung erfolgt wie in Abschnitt „Einstellung der Parameter“ beschrieben. Der einstellbare Pegelbereich liegt zwischen: ❙❙ –135 dBm bis +13 dBm ohne Amplitudenmodulation ❙❙ –135 dBm bis +7 dBm mit Amplitudenmodulation ❙❙ Die Auflösung beträgt 0,1 dBm. Der angezeigte Pegelwert bezieht sich auf eine Lastimpedanz von 50 Ω. Die Auswahl der Einheit dBm, mV oder µV erfolgt mit der Tastatur 11 . Entsprechend der Bereichswahl beträgt die Auflösung des Pegelwerts 3 Digit. Achtung! Bei eingeschalteter Amplitudenmodulation wird das Ausgangssignal automatisch auf +7 dBm begrenzt, um eine Übersteuerung der Ausgangsverstärkers zu verhindern. 3.9 Wahl der Modulationsart Nach Betätigung der MOD.-Funktionstaste 9 zeigt das Display: MODULATION MENU AM FM PM – –> MODULATION MENU <– – FSK PSK GATE 8 Die Formänderung des Modulationssignals erfolgt mit den kontextsensitiven Tasten 5 . Die aktuelle Signalform ist mit einem Dreieck gekennzeichnet. Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Nach Auswahl der Option Fmod (AM MENU) zeigt das Display: Die Frequenz des Modulationssignals kann direkt mittels der Tastatur 11 eingegeben, mit dem Drehknopf 10 variiert oder mit den kontextsensitiven Tasten 5 geändert werden. Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Der einstellbare Frequenzbereich ist: – 10 Hz bis 200 kHz: Sinus (Schrittweite10 Hz) – 10 Hz bis 20 kHz: Dreieck, Rechteck, Sägezahn (Schrittweite jeweils 10 Hz) Die Bedienung des HM8135 Durch einmaliges Drücken der kontextsensitiven Taste 5 unterhalb der Anzeige off wird die interne Modulationsquelle eingeschaltet (INT). Bei nochmaligen Drücken wird die externe Modulationsquelle eingeschaltet (EXT). Die jeweils gewählte Quelle wird mit einem nebenstehenden Dreieck angezeigt. Die MOD.OUTPUT-LED leuchtet. In diesem Beispiel besteht das externe Modulationssignal aus einem trinary-Code, bestehend aus 9 Bits, 1 Bit besteht aus zwei schmalen oder breiten Impulsen, abhängig von der erwarteten Kombination: ❙❙ Ein Bit bestehend aus einem breiten und einem schmalen Bit wird OPEN genannt. ❙❙ Ein Bit bestehend aus zwei schmalen Bits wird LOW genannt. ❙❙ Ein Bit bestehend aus zwei breiten Bits wird HIGH genannt. Wird die kontextsensitive Taste 5 ein weiteres Mal betätigt, wird die Modulation deaktiviert (OFF). Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Bei externer AM-Modulation besteht nur die Option der Modulationsgradeinstellung. Siehe hierzu den Abschnitt „Amplitudenmodulation“. Die externe Modulationsfrequenz für AM muss im folgenden Bereich liegen: 10 Hz bis 100 kHz. Für die Erkennung des ersten Bits dient ein Synchronisations-Bit (long low level). Die Modulationsfrequenz beträgt 20 Hz. Bei externer FM oder PM können die folgenden Einstellungen vorgenommen werden: ❙❙ DC gekoppelt (DC – 100 kHz) ❙❙ AC gekoppelt (100 Hz – 100 kHz) ❙❙ Hub (siehe hierzu den entsprechenden Abschnitt) CH1:Modulation: Schmaler Impuls mit 200 µs Breite Breiter Impuls mit 1,8 ms Breite Synchronisations-Bit mit 14 ms Breite CH2: Zoom von CH1 Beispiel 1: CH1: Demoduliertes Signal: DC gekoppelt CH2: Demoduliertes Signal: AC gekoppelt Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. CH1:Modulation: Erster Impuls mit einer Breite von 150 µs Zweiter Impuls mit einer Breite von 1,1 ms Periodendauer 2,5 ms (Fmod: 400 Hz) CH2: Moduliertes Signal (Frequenzhub: 2 kHz) Der externe Modulationseingang befindet sich auf der Frontseite (MOD.INPUT). Bei externer Modulation darf die Signalform beliebig sein, die Anzeige des Modulationsgrades und des Frequenzhubs ist jedoch nur korrekt bei Zuführung eines Signals mit einer Amplitude von 2 Veff. Beispiel 2: 9 Modulationsarten 4Modulationsarten Beispiel 5: Für AM Dreieck (Modulationsgrad: 50%) erhält man: 4.1 Amplitudenmodulation (AM) Nach Auswahl der Option D% (AM MENU) mittels der kontextsensitiven Tasten 5 zeigt das Display: Ein neuer Funktionswert kann über die Tastatur 11 , mit dem Drehknopf 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Die Bedienung erfolgt wie im Abschnitt „Einstellung der Parameter“ beschrieben. Der Modulationsgrad kann in einem Bereich von 0 bis 100% eingestellt werden. Die Auflösung beträgt 0,1% Beispiel 6: Für AM positive Rampe (Modulationsgrad: 50%) erhält man: Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. Beispiel 3: Für AM Sinus (Modulationsgrad: 50%) erhält man: Beispiel 7: Für AM negative Rampe (Modulationsgrad: 50%) erhält man: Beispiel 4: Für AM Rechteck (Modulationsgrad: 50%) erhält man: 4.2 Frequenzmodulation (FM) Nach Auswahl der Option Dev (FM MENU) mittels der kontextsensitiven Tasten 5 zeigt das Display: Ein neuer Funktionswert kann über die Tastatur 11 , mit dem Drehgeber 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Die Bedienung erfolgt wie im Ab10 Modulationsarten schnitt 3.6: Einstellung der Parameter beschrieben. Der Frequenzhub kann mit einer 100 Hz-Schrittweite, abhängig von der Trägerfrequenz gewählt werden: ❙❙ ±200 Hz bis ±150 kHz (<16 MHz) ❙❙ ± 2 kHz bis ±400 kHz (16 - 250 MHz) ❙❙ ± 1 kHz bis ±100 kHz (250 - 500 MHz) ❙❙ ± 1 kHz bis ±200 kHz (500 -1000 MHz) ❙❙ ± 2 kHz bis ±400 kHz (1000 -3000 MHz) Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. Beispiel 8: Für FM Sinus erhält man: Ein neuer Funktionswert kann über die Tastatur 11 , mit dem Drehknopf 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Die Bedienung erfolgt wie im Abschnitt 3.6: Einstellung der Parameter beschrieben. Der Bereich des Frequenzhubs kann abhängig von der Trägerfrequenz gewählt werden von: ❙❙ 0 bis 3.14 rad (<16 MHz) ❙❙ 0 bis 10 rad (16 – 3000 MHz) ❙❙ Schrittweite 0,01 rad Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. Beispiel 10: Für PM Sinus (Frequenzhub: 1 rad) erhält man: (Frequenzhub: 400 kHz) Beispiel 9: Für FM Rechteck erhält man: Beispiel 11: Für PM Rechteck erhält man: CH1:Modulationssignal CH2: Moduliertes Signal (Frequenzhub: 80 kHz) 4.3 Phasenmodulation (PM) Nach Auswahl der Option Dev (PM MENU) mittels der kontextsensitiven Tasten 9 zeigt das Display: CH1:Modulationssignal CH2: Moduliertes Signal (Frequenzhub: 1 rad) 11 Modulationsarten 4.4 FSK Modulation Nach Auswahl der Optionen F0 oder F1 (FSK-MENU) mittels der kontextsensitiven Tasten 5 zeigt das Display: Fsk0: 512.000000 MHz – stp + cur zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. Beispiel 13: Für PSK-Modulation erhält man: 1200.000000 MHz +13.0dBm PSK Ext Fsk1: 522.000000 MHz – stp + cur Ein neuer Wert für die Parameter Fsk0 bzw. Fsk1 kann über die Tastatur 11 , mit dem Drehgeber 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Die Bedienung erfolgt wie im Abschnitt 3.6: Einstellung der Parameter beschrieben. Der Frequenzhub von Fsk0 Fsk1 bzw. Fsk1 Fsk0 kann in folgendem Bereich liegen: ❙❙ 0 bis 10 MHz (16 MHz – 3000 MHz) ❙❙ Schrittweite 1 Hz Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. Psk0: –3,14 rad; Psk1: 3,14 rad; Fmod: 1 kHz; Level TTL Beispiel 12: Für FSK-Modulation erhält man: 1190.000000 MHz 1200.000000 MHz FSK Ext Fsk0: 1190.000000 MHz Fsk1: 1200.000000 MHz 4.5 PSK Modulation Nach Auswahl der Optionen PH0 oder PH1 (PSK-MENU) mittels der kontextsensitiven Tasten 5 zeigt das Display: Psk0: – stp + –10.00rad cur Psk1: – stp + 10.00rad cur Ein neuer Wert für die Parameter Psk0 bzw. Psk1 kann über die Tastatur 11 , mit dem Drehgeber 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Die Bedienung erfolgt wie im Abschnitt 3.6: Einstellung der Parameter beschrieben. Der Phasenhub von Psk0 Psk1 bzw. Psk1 Psk0 kann in folgendem Bereich liegen: ❙❙ –3.14 rad bis 3.14 rad (<16 MHz) ❙❙ –10 rad bis 10 rad (>16 MHz) ❙❙ Schrittweite 0.01 rad Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt 12 Psk0: 0 rad; Psk1: 3,14 rad; Fmod: 1 kHz; Level TTL 4.6GATE-Modulation Die GATE-Modulation steuert den RF-Ausgang mit einem Rechtecksignal. Die Modulation ist dabei abhängig von: ❙❙ Ein/Aus Verhältnis des Rechtecksignals ❙❙ Anstiegs / Abfallzeit des Rechtecksignals ❙❙ Verzögerungszeit des Rechtecksignals Das GATE-Signal (TTL-Pegel) wird dem Instrument auf der Geräterückseite über den Eingang GATE INPUT 19 zugeführt. Im aktiven Zustand (wahlweise 1 oder 0) bewirkt das Gate-Signal ein Durchschalten des Trägersignals zum Ausgang. Nach Auswahl der Option GATE (MODULATION MENU) mittels einer der kontextsensitiven Tasten 5 zeigt das Display: Gerätekonfiguration Mittels der kontextsensitiven Tasten wird der Pegel zur Signalaktivierung festgelegt. Die beiden Dreiecke zeigen bzw. und on bzw. off. den Betriebszustand Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. Die GATE-Modulation kann jederzeit mit einer anderen Modulationsart verbunden werden, z.B. mit AMsin oder Fmod = 10 kHz. Beispiel 14: (Fgate: 250 Hz Sqr) 5 Einstellen der Gerätekonfiguration 5.1Schrittauswahl Nach Betätigung der Funktionstaste STEP 9 zeigt das Display das Step-Menü: *** Freq STEP MENU Level Fmod *** ––> *** <–– STEP MENU FM Phi *** D% GATE Mittels der kontextsensitiven Tasten 5 wird die entsprechende Option ausgewählt. Ist der Parameter schon ausgewählt, kann mit der STEP-Taste 9 die Schrittart direkt gewählt werden. Bei nochmaligen Drücken der Taste wird zur vorherigen Anzeige zurückgeschaltet. CH1: AM Signal (Modulationsgrad: 50%) und GATEModulation CH2: Signal mit GATE-Modulation Ein neuer Funktionswert kann über die Tastatur 11 , mit dem Drehgeber 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Die Bedienung erfolgt wie im Abschnitt „Einstellung der Parameter“ beschrieben. Die verschiedenen Schrittfunktionen sind: ❙❙ FSTEP: (Frequenz) ❙❙ Level STEP: (Pegel) ❙❙ Fmod STEP: (Modulationsfrequenz) ❙❙ AM STEP: (AM-Modulationsgrad) ❙❙ FM STEP: (FM-Frequenzhub) ❙❙ Phi STEP: (PM-Hub) 5.2MENU-Taste Offs MAIN MENU Ref Sfc SWEEP Mit der MENU-Taste 7 erfolgt der Zugriff auf das Konfigurations-Menü. Optionen werden mittels der kontextsensitiven Tasten 5 ausgewählt. Mit der ESC-Taste 13 wird zum Haupt-Display umgeschaltet: 13 Gerätekonfiguration 5.3 Offset Korrektur (ab Firmware-Version 1.23) Nach Auswahl der Option Offs im Konfigurations-Menü zeigt das Display: * LEV. OFFSET Att. On MENU * Off On Die Kompensierung eines angeschlossenen Dämpfungsgliedes wird aktiviert. Der Ausgangspegel wird entsprechend dem Wert des Dämpfungsgliedes angepasst. Off Die Kompensierung eines angeschlossenen Dämpfungsgliedes wird deaktiviert. Der Ausgangspegel wird dementsprechend angepasst. Att. Ermöglicht die Anpassung des externen Abschwächerwertes. Wenn diese Funktion aktiviert ist, wird die tatsächliche Dämpfungshöhe des externen Abschwächers berücksichtigt. Der Ausgangspegel am Ausgang des Generators setzt sich zusammen aus: Pset + Att mit Pset = programmierter Ausgangspegel in dBm, Att = Dämpfungswert in dB. Wenn der tatsächlich eingestellte Pegel oberhalb Pmax + Att ist, wird der Ausgangspegel automatisch verringert, damit der Ausgangspegel des Generators nie den maximalen Pegel (+13 dBm bei deaktivierter Amplitudenmodulation (AM) oder +7 dBm bei aktivierter Amplitudenmodulation) überschreitet. Wird die Abschwächer-Korrektur ausgeschaltet (Off) und der tatsächliche Pegel (LEVEL) ist auf den Minimalwert von -135 dBm eingestellt, wird der Pegel automatisch auf -135 dBm eingestellt. Att.: – stp + 20.0dB cur tigt. Der zulässige Pegelbereich sinkt durch die Höhe des Dämpfungswertes. Beispiel: Mit 20,0 dB Dämpfung und deaktivierter Amplitudenmodulation (AM OFF) kann der Pegel von -147 dBm bis -7 dBm eingestellt werden. Ist die Kompensation des Dämpfungsgliedes aktiv, so wird der Punkt durch einen Doppelpunkt in der Amplitudenanzeige ersetzt: Level: -140:0 dBm cur – stp + 5.4 Referenz REF Zur Grundausstattung des HM8135 gehört ein temperaturkompensierter Quarzoszillator (TCXO = Temperature Controlled Crystal Oscillator) mit einer Referenzfrequenz von 10 MHz. Nach jedem Zugriff auf das Konfigurations-Menü mittels der kontextsensitiven Taste Ref 5 erfolgt ein PLL-Test des Referenzoszillators (verriegelt und entriegelt). Die interne Referenzfrequenz ist über den Ausgang REF. OUPUT 10 MHz verfügbar. Die Zufuhr einer externen Referenzfrequenz ist über den rückwärtigen Eingang REF. INPUT 10 MHz möglich. Achtung! Bei falscher externer Referenzfrequenz erfolgt die Fehlermeldung error und ein automatisches Umschalten auf die interne Referenzquelle. 5.5Spezialfunktionen SfC Nach Auswahl der Option SFC im Konfigurations-Menü zeigt das Display: Die Einstellungen des Level Offset werden automatisch im nichtflüchtigen Speicher gespeichert. Mit der PREV.-Taste wird das Menü ohne zu speichern verlassen. Die Dämpfung der externen Abschwächer können auch direkt über die Tastatur eingegeben werden. Zur Bestätigung der Werteeingabe wird die dBm-Taste gedrückt. Der Wert kann in 1 dB Schritten mit der - und + Taste erhöht oder verringert werden. Alternativ kann der Wert auch mit Hilfe des Drehgebers oder den Cursor-Tasten eingestellt werden. Wenn der Dämpfungswert geändert wird, aktualisiert sich der Ausgangspegel entsprechend. Der zulässige Regelbereich ist von 0,0 dB bis 30,0 dB. Mit der PREV.– Taste gelangt man in das Offset-Hauptmenü zurück. Nutzung des Level Offset Bei der Einstellung der Ausgangspegel werden die externen Abschwächer der angezeigten Ebene berücksich14 Disp Mit Hilfe der kontextsensitiven Tasten 5 werden die einzelnen Spezialfunktionen ausgewählt. 5.6Beeper BeeP Der eingebaute akustische Alarmgeber quittiert jede manuelle Fehlbedienung. Die Aktivierung und Einstellung des Beepers erfolgt im Beeper Setup Menü: ❙❙ Soft (leiser Ton) ❙❙ Loud (lauter Ton) ❙❙ None (kein Ton) Gerätekonfiguration Mit Hilfe der kontextsensitiven Tasten 5 werden die einzelnen Funktionen ausgewählt. Ein Dreieck zeigt den entsprechenden Betriebsstatus. 5.7Drehgeber Enco (Encoder) Die Aktivierung des digitalen Drehgebers erfolgt mittels der kontextsensitiven Tasten 5 im Menü ENCODER SETUP. Ein Dreieck zeigt den entsprechenden Betriebsstatus (ON or OFF). 5.8 Interface COM Das Instrument HM8135 ist in seiner Grundausstattung mit einer USB/RS-232 Schnittstelle ausgerüstet. Optional kann eine IEEE-488 (GPIB) Schnittstelle eingebaut werden (alle galvanisch getrennt). Die Schnittstellenparameter von IEEE-488 und USB-Schnittstelle können nicht verändert werden. Die optionale Schnittstelle kann mittels der kontextsensitiven Tasten ausgewählt werden. Standardmäßig ist nach dem Einschalten die Dual-Schnittstelle aktiviert. Soll nach dem Einschalten die optionale Schnittstelle aktiviert sein, speichern Sie die Geräteeinstellung (mit aktivierter optionaler Schnittstelle) im Gerätespeicher 0 ab. Serielles Interface 5.9 Display LCD Der Kontrast und die Helligkeit der Anzeige wird mittels der kontextsensitiven Tasten 5 eingestellt ( + oder – ). ** DISPLAY ADJUST ** -Contrast+ -Light+ 5.10SWEEP Nach Auswahl der Option SWEEP im Konfigurationsmenü zeigt das Display: *** SWEEP MENU Param Mode Trig Durch Drücken der kontextsensitiven Tasten 5 können die folgenden Parameter ausgewählt und anschließend verändert werden: ❙❙ Param (Parametereinstellung) ❙❙ Mode (Continue- / Burst-Betrieb) ❙❙ Trig (ON / OFF) ❙❙ ON / OFF (Sweep – Status) Der Trigger kann bereits in diesem Menüpunkt an- bzw. ausgeschaltet werden. Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Nachdem mit den kontextsensitiven Tasten 5 eine der Optionen Param oder Mode ausgewählt wurde, zeigt das Display: * Die Übertragungsrate wird mittels der kontextsensitiven Tasten 5 eingestellt. Es kann eine Übertragungsrate von 300, 600, 1200, 2400, 4800, 9600 oder 19200 Baud gewählt werden. Alle anderen Parameter sind nicht veränderbar: ❙❙ keine Parität ❙❙ 8 Datenbits ❙❙ 1 Stopbit Zur Verbindung zwischen Messgerät und PC benötigen Sie ein normales 1:1 RS-232 Kabel. USB-Schnittstelle Der Synthesizer muss nicht konfiguriert werden. Bei Bedarf kann die Baudrate geändert werden. Verbinden Sie den HM8135 mit einem USB-Kabel mit Ihrem PC und installieren Sie die Treiber der USB-Schnittstelle wie im Handbuch der USB-Schnittstelle (HO820) beschrieben. *** Off SWEEP PARAM MENU * Up Span Steps * SWEEP SPAN MENU * LowFreq HighFreq FrLo: 16.000000 MHz cur – stp + FrHi: 1.200000000 GHz cur – stp + Ein neuer Wert für die Parameter FrLo und FrHi kann über die Tastatur 11 , mit dem Drehgeber 10 oder mit den kontextsensitiven Tasten 5 eingestellt werden. Der Frequenzhub zwischen FrLo FrHi kann in folgendem Bereich liegen: ❙❙ 1 MHz...3 GHz ❙❙ Schrittweite 1 Hz IEEE-488 (GPIB)-Schnittstelle (Option) Sie müssen lediglich die GPIB-Adresse des Gerätes an der GPIB-Schnittstelle auf der Geräterückseite einstellen und mit einem GPIB-Kabel an Ihren PC anschließen. Einstellungen können nur vor dem Starten des Gerätes erfolgen, während dem Betrieb ist dies nicht möglich. 15 Gerätekonfiguration * SWEEP STEP MENU * StepCount steptime Step Count: – val + Step Time: – val + 100 cur 0.10 sec cur Die Parameter können im folgendem Bereich liegen: ❙❙ max. 500 Schritte ❙❙ Schrittweite 10 ms (max. 2,5 s) Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. 5.11Mode: * SWEEP MODE MENU * Continue Burst ––> Sweep Count: – val + 5.13 PREV. Taste (Previous) Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. 5.14ON-Taste Der Signalausgang RF OUTPUT 14 wird mit der Taste ON 12 aktiviert und die LED ON leuchtet. Im nichtaktivierten Zustand ist der Signalausgang ein offener Ausgang (open circuit). 5.15 RCL-STO Tasten (Recall & Store) Der HM8135 bietet die Möglichkeit, neben der zuletzt gewählten Systemeinstellung, 10 komplette Geräteeinstellungen nichtflüchtig abzuspeichern. Jede einzelne Konfiguration speichert alle zu diesem Zeitpunkt aktiven Parameter wie Frequenz, Amplitude, Modulation, etc. Eine gespeicherte Konfiguration kann zu jedem beliebigen Zeitpunkt, auch nach erneutem Einschalten des Instruments, wieder aufgerufen werden. Speicherung und Rückruf erfolgt über die Tasten RCL (Aufruf) und STO (Speichern). Nach Betätigung der STO-Taste 6 zeigt das Display: 10 cur Mit den kontextsensitiven Tasten 5 kann die Auswahl im Menüpunkt Mode bestätigt werden. Die aktuelle Konfiguration wird mit einer Zahl zwischen 0-9 (numerische Tastatur) abgespeichert. Nach Betätigung der RCL-Taste 4 zeigt das Display: 5.12Trig: SWEEP TRIGGER on SIGNAL off In diesem Menüpunkt kann die Flanke des Triggersignals (steigend oder fallend) eingestellt bzw. an- / ausgeschaltet werden. Die Auswahl erfolgt wieder mit den kontextsensitiven Tasten 5 . Mit der PREV.-Taste 3 wird zum vorherigen Menüpunkt zurückgeschaltet. Mit der ESC-Taste 13 wird zum HauptDisplay umgeschaltet. Nach Beendigung der Parametereingaben zeigt das Display folgende Angaben: 1.16.000000MHz 1.200000000GHz SWE 10.0s Unter SWE im Display ist die errechnete SWEEP-Zeit dargestellt, die sich wie folgt berechnet: 16 Step Count * Step Time hier: 100 * 0,1s = 10s Eine abgespeicherte Konfiguration wird mit einer Zahl zwischen 0-9 (numerische Tastatur) aufgerufen. Fernbedienung 6Fernbedienung 6.1Schnittstellen Das Gerät kann über diese Schnittstellen vom PC aus programmiert werden. Funktionen und Bereiche können geschaltet und Messdaten eingelesen werden, die im Gerät gesammelt wurden. Die Treiber für diese Schnittstellen finden sie sowohl auf der dem Messgerät beigelegten Produkt-CD, als auch auf http://www.hameg.com. Die im HM8135 verwendete Dual-Schnittstelle USB/RS232 (HO820) oder GPIB-Schnittstelle (HO880) ist vom Messkreis galvanisch getrennt. RS-232 Schnittstelle (DB-9 Stecker) Nur diese drei Anschlüsse sind verdrahtet: ❙❙ Pin 2 = Txd (Daten senden). ❙❙ Pin 3 = Rxd (Daten empfangen). ❙❙ Pin 5 = Gnd (Masse). Die elektrischen Spannungen (+12/-12V max.) an den Datenleitungen müssen der V24 (RS-232) Norm entsprechen, um einen problemlosen Datenaustausch mit der Standard COM-Schnittstelle eines Personal Computers zu gewährleisten. Das Übertragungsprotokoll ist ein Xon/Xoff-Protokoll. Der Befehl #X1 aktiviert ein Softwarehandshaking. Die Übertragung zwischen Rechner und Interface ist nun nicht mehr durch die Hardware-Handshake-Leitungen synchronisiert, sondern durch 2 vereinbarte Befehle: XON = 11h = Übertragung fortsetzen XOFF = 13h = Übertragung anhalten Nachdem das Instrument eine Befehlszeile erhalten hat, sendet es den Xoff Charakter (19 dez.) zurück. Nachdem vom Empfänger alle Kommandos ausgeführt wurden, wird dies mit dem Xon Charakter (17 dez.) quittiert und somit ist eine neue Übertragung möglich. Die Befehle sind für alle Schnittstellentypen identisch. Für genauere Informationen ist das jeweilige Interface-Handbuch zu benutzen. 1000.000000MHz REMOTE NoMod LOCAL Nach Erhalt des Remote-Befehls zeigt das Display in der zweiten Zeile mit einem Dreieck den aktivierten Betriebszustand REMOTE. Mit der kontextsensitiven Taste 5 unterhalb der Anzeige LOCAL kann zurück in den LOCAL Modus gewechselt werden (alle anderen Tasten sind verriegelt). dows HyperTerminal finden sie in unserer Knowledge Base unter http://www.hameg.com/hyperterminal. USB-Schnittstelle Das Messgerät muss nicht konfiguriert werden. Bei Bedarf kann die Baudrate geändert werden. Verbinden Sie den HM8135 mit einem USB-Kabel mit Ihrem PC und installieren Sie die Treiber der USB-Schnittstelle wie im Handbuch der USB-Schnittstelle beschrieben. IEEE-488 (GPIB)-Schnittstelle (Option) Sie müssen lediglich die GPIB-Adresse des Gerätes an der GPIB-Schnittstelle auf der Geräterückseite einstellen und mit einem GPIB-Kabel an Ihren PC anschließen. Einstellungen können nur vor dem Starten des Gerätes erfolgen, während dem Betrieb ist dies nicht möglich. 6.2 Nachrüstung einer Schnittstelle Wenn Sie ein die Schnittstelle in einem HM8135 nachrüsten oder tauschen wollen, so folgen Sie bitte den Anweisungen aus dem Handbuch der Schnittstelle, wie diese eingebaut wird und welche Jumper gesetzt werden müssen. Zusätzlich müssen Sie den HM8135 programmieren, um die neue Schnittstelle zu aktivieren. Dazu senden Sie bitte das entsprechende Kommando über die serienmässig eingebaute RS-232 Schnittstelle gemäß nachfolgender Tabelle: SchnittstelleKommando USB (HO870/HO820) 813xcom2default:1 IEEE/GPIB (HO880) 813xcom2default:2 RS-232 (HO890) 813xcom2default:3 Um alle zusätzlichen Schnittstellen zu deaktivieren, senden Sie bitte: 813xcom2default:0 Sie können ein Terminalprogramm nutzen, um diese Befehle zu senden. Wir empfehlen das Windows Hyperterminal. Eine Installations- und Nutzeranleitung dazu können Sie von der HAMEG Website www.hameg.com/hyperterminal herunterladen. Der Anwender kann mit dem Befehl LK1 alle Bedienungselemente sperren. Das Display zeigt dann: 6.3 Unterstützte Befehle Allgemein Es gibt zwei Befehlsarten. Die erste Gruppe ist abwärtskompatibel zur Steuerung des HM8133-2. Die zweite im Folgenden beschriebene Gruppe ist ein Befehlssatz der in seiner Syntax dem SCPI-Standard entspricht. Es wird empfohlen nur diese Befehle zu verwenden. Um eine erste Kommunikation herzustellen, benötigen Sie ein serielles Kabel (1:1) und ein beliebiges Terminal Programm wie z.B. Windows HyperTerminal, das bei jedem Windows Betriebssystem enthalten ist. Eine detailierte Anleitung zur Herstellung der ersten Verbindung mittels Win- Befehle werden zeilenweise zum Instrument gesendet, wobei eine Zeile einem ASCII-Code zwischen 20 und 127 (dezimal) entspricht, abgeschlossen mit einem „End of Line“Zeichen (10 oder 13+10 = LF, CR+LF). Jede Befehlszeile besteht aus einem oder mehreren Befehlen, separiert mit einem Semikolon “;“ (entspricht der C-Sprache). Beispiel: :POWER 7 ; :FREQ 500E+6 ; :OUTP ON 17 Fernbedienung Der Ausgangspegel beträgt +7 dBm, die Signalfrequenz 500 MHz und der RF-Ausgang ist aktiviert. Das Gerät erkennt sowohl Groß- als auch Kleinbuchstaben. Mit einem Befehl wird das Instrument in einen bestimmten Zustand versetzt. Mit einem weiteren Befehl kann dieser Zustand oder der entstandene Messwert abgefragt werden. Alle Befehle, die sich auf eine Funktion beziehen (z.B. POWER), sind in einer Befehlsgruppe zusammengefasst, die in den nachfolgenden Absätzen beschrieben werden. 6.4 Beschreibung der Befehle Syntaxkonvention Folgende Syntaxkonventionen sind gültig: ❙❙ Kleinschreibung ist optional, d. h. der Datenstring OUTPut kann in Kurzschreibweise mit OUTP oder ausgeschrieben mit OUTPUT bezeichnet werden. ❙❙ [ ] Ein Datenstring in rechteckigen Klammern ist optional. ❙❙ | Eine Exklusiv-Oder-Verknüpfung zwischen den einzelnen Parametern. ❙❙ NR1 Der Datenstring ist eine Ziffernfolge ohne Komma stelle (123456). ❙❙ NR2 Der Datenstring ist eine Ziffernfolge mit Komma stelle (1234.56). ❙❙ NR3 Der Datenstring ist eine Ziffernfolge mit Komma stelle und Exponent (1234.56E+3). Initialisierung *RST Entspricht dem Drücken der ESC-Taste beim Einschalten, außer Beeper, Display und Speicherbelegung (0–9), die bei der Initialisierung nicht geändert werden. 6.5 Generelle Befehle *IDN? Identifikation *SAV x Speichert die aktuelle Systemkonfiguration (x von 0 bis 9) *RCL x Aufruf einer Systemkonfiguration (x von 0 bis 9) SNR? Seriennummer des Instruments FAB? Fabrikationsdatum des Instruments 6.6 Bus Befehle LK0 Lokaler Modus aktiviert LK1 Lokaler Modus nicht aktiviert (alle Bedienele mente sind verriegelt) RM0 Fernsteuerung aus RM1 Fernsteuerung ein 6.7 Sound Befehle BP0 Beep aus BPS leiser Beep BPL lauter Beep 6.8 Befehle OUTPUT Ein- und Ausschalten des RF-Ausgangs. Syntax: :OUTPut[:STATe] 0 | OFF | 1 | ON (1) :OUTPut[STATe]? (2) Mit Befehlszeile (1) wird der RF-Ausgang aktiviert oder de 18 aktiviert. Die Parameter 0 oder OFF deaktivieren den RFAusgang (wenn aktiviert), 1 oder ON aktivieren den RFAusgang. Befehlszeile (2) dient der aktuellen Statusabfrage. Das Instrument sendet 0 bei nicht aktiviertem RFAusgang und sendet 1 bei aktiviertem RF-Ausgang. Beispiele: :OUTP ON Ausgang Ein :OUTP 1 Ausgang Ein :OUTPUT ON Ausgang Ein :OUTPUT:STATE 1 Ausgang Ein :OUTP? Abfrage des aktuellen Ausgangsstatus :OUTPUT:STATE? Abfrage des aktuellen Ausgangsstatus 6.9 Befehle POWER Änderung des RF-Ausgangspegels Syntax: :POWer[:LEVel] <NUM> (1) :POWer[:LEVel]? (2) :POWer:UNIT V | DBM (3) :POWer:UNIT? (4) Befehlszeile (1) dient der Pegeleinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR2 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der aktuell eingestellten Einheit. Befehlszeile (2) dient der aktuellen Pegelabfrage des Instruments. Es wird ein der Auflösung entsprechender NR2 Datenstring gesendet, ohne Angabe der Einheit (wie z. B. dBm). Mit Befehlszeile (3) wird die gewünschte Einheit eingestellt. Zwei Parameter stehen zur Auswahl: V für mV bzw. µV und DBM für dBm. Befehlszeile (4) fragt den aktuellen Einheitswert ab. Das Instrument antwortet mit dem entsprechenden Datenstring (z.B. DBM). Beispiele: :POW:UNIT DBM Setzt den Pegel in dBm :POWER:UNIT DBM Setzt den Pegel in dBm :POW 5.7 Setzt den Pegel auf 5.7 dBm :POW:LEV 5.7 Setzt den Pegel auf 5.7 dBm :POWER:UNIT? Abfrage der aktuellen Einheit 6.10 Befehle FREQUENCY Änderung der RF-Ausgangsfrequenz (Träger) Syntax: :FREQuency[:CW|:FIXed] <NUM> (1) :FREQuency[:CW|:FIXed]? (2) Befehlszeile (1) dient der Frequenzeinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR1,NR2 oder NR3 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der Einheit Hz (z.B. 34000000 Hz für 34 MHz). Die Optionen :CW und :FIXed haben auf das Instrument keine Wirkung. Sie dienen lediglich der Kompatibilität mit dem SCPI Standard. Befehlszeile (2) dient der aktuellen Frequenzabfrage des Instruments. Das Instrument sendet einen der Auflösung entsprechenden NR3 Datenstring ohne Einheit. Fernbedienung Beispiele: :FREQ 678E+6 Setzt die Frequenz auf 678 MHz :FREQUENCY 34000000 Setzt die Frequenz auf 34 MHz :FREQ? Abfrage der aktuellen Frequenz :FREQ:FIX 900E+6 Setzt die Frequenz auf 900 MHz 6.11 Befehle PHASE Auswahl der internen oder externen Referenzquelle Syntax: :PHASe:SOURce INTern | EXTern (1) :PHASe:SOURce? (2) Befehlszeile (1) dient der Referenzquellenwahl. Nur einer der beiden Parameter ist erforderlich: INTern aktiviert die interne Referenzquelle und EXTern aktiviert die externe Referenz. Befehlszeile (2) dient der aktuellen Referenzquellenabfrage des Instruments. Das Instrument sendet den Datenstring INT oder EXT entsprechend der eingestellten Referenzquelle. Anmerkung: Nach einem Setzbefehl (1) wird dringend empfohlen den aktuellen Systemzustand mit einem Abfragebefehl (2) zu überprüfen. Beispiele: :PHAS:SOURCE EXT Externe Referenzquelle aktiviert :PHASE:SOUR? Abfrage der Referenzquelle :PHAS:SOUR? Abfrage der Referenzquelle (Kurzschreibweise) 6.12 Befehle PULM (PULse Modulation / Gate) Syntax: :PULM:STATe 1 | ON | 0 | OFF (1) :PULM:STATe? (2) Befehlszeile (1) dient der GATE Modulationswahl. Die Parameter 1 oder ON aktivieren die GATE Modulation. Die Parameter 0 oder OFF deaktivieren die Modulation (wenn aktiviert). Befehlszeile (2) dient der aktuellen Modulationsstatusabfrage. Das Instrument sendet 0 bei nicht aktivierter GATE Modulation und sendet 1 bei aktivierter GATE Modulation. :PULM:POLarity NORMal | INVert (3) :PULM:POLarity? (4) Befehlszeile (3) setzt den Validationspegel der GATE Modulation. Der Parameter NORMal steht für Großsignal Validation. Der Parameter INVert steht für Kleinsignal Validation. Befehlszeile (4) dient der aktuellen Validationsabfrage. Das Instrument sendet den Datenstring 1 für NORMal und sendet 0 für INVert. 6.13 Befehle AM (Amplituden-Modulation) Syntax: :AM[:DEPTh] <NUM> (1) :AM[:DEPTh]? (2) Befehlszeile (1) dient Modulationsgradeinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR2 Daten-string (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der Einheit %. Ist die Auflösung <0.1%, wird der Wert zur nächst höheren Stelle hin aufgerundet. Befehlszeile (2) dient der aktuellen Modulationsgradabfrage. Das Instrument sendet einen NR2 Datenstring mit einer Auflösung von x.1 ohne Einheit (%). :AM:SOURce INTern | EXTern (3) :AM:SOURce? (4) Befehlszeile (3) dient der AM Referenzquellenwahl und aktiviert gleichzeitig die AM Modulation. Nur einer der beiden Parameter ist erforderlich: INTern aktiviert die interne Referenzquelle und EXTern aktiviert die externe Referenz. Befehlszeile (4) dient der aktuellen Referenzquellenabfrage. Das Instrument sendet den Datenstring INT oder EXT (nicht INTERN oder EXTERN), entsprechend der eingestellten Referenzquelle. Ist die AM Modulation abgeschaltet, sendet das Instrument INT als Standardwert für den Befehl AM:STAT 1 (analog zur manuellen Bedienung). :AM:INTern:FREQuency <NUM> (5) :AM:INTern:FREQuency? (6) Befehlszeile (5) dient der AM Modulationsfrequenzeinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR1, NR2 oder NR3 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der Einheit Hz (z.B. 34000000 Hz für 34 MHz). Befehlszeile (6) dient der aktuellen AM Modulationsfrequenzabfrage. Das Instrument sendet einen NR3 Datenstring ohne Einheit. :AM:INTern:SHAPe SIN | SQU | TRI | +RP | -RP (7) :AM:INTern:SHAPe? (8) Die Befehlszeile (7) dient der Signalformeinstellung des internen Modulationssignals. Die Parameter sind: SIN für Sinussignal, SQR für Rechtecksignal, TRI (Triangle) für Dreiecksignal, +RP für positives Rampensignal und -RP für negatives Rampensignal. Befehlszeile (8) dient der aktuellen Signalformabfrage. Das Instrument antwortet mit dem entsprechenden Datenstring (z. B. +RP). :AM:STATe 0 | OFF | 1 | ON (9) :AM:STATe? (10) 19 Fernbedienung Befehlszeile (9) dient der AM Modulationswahl. Die Parameter 1 oder ON aktivieren die AM Modulation. Die Parameter 0 oder OFF deaktivieren die AM Modulation (wenn aktiviert). Befehlszeile (10) dient der aktuellen AM Modulationsabfrage. Das Instrument sendet 0 bei nicht aktivierter AM Modulation und sendet 1 bei aktivierter AM Modulation. Beispiel: :AM:INT:FREQ 3000; SHAP SQU; DEPT 60; STAT 1 6.14 Befehle FM (Frequenz-Modulation) Syntax: :FM[:DEViation] <NUM> (1) :FM[:DEViation]? (2) Befehlszeile (1) dient der FM Frequenzhubeinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR1, NR2 oder NR3 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der Einheit Hz (z.B. 34000000Hz für 34 MHz). Befehlszeile (2) dient der aktuellen Frequenzhubabfrage. Das Instrument sendet einen NR3 Datenstring ohne Einheit. :FM:SOURce INTern | EXTern (3) :FM:SOURce? (4) Befehlszeile (3) dient der FM Referenzquellenwahl und aktiviert gleichzeitig die FM Modulation. Nur einer der beiden Parameter ist erforderlich: INTern aktiviert die interne Referenzquelle und EXTern aktiviert die externe Referenz. Befehlszeile (4) dient der aktuellen Referenzquellenabfrage. Das Instrument sendet den Datenstring INT oder EXT (nicht INTERN oder EXTERN), entsprechend der eingestellten Referenzquelle. Ist die FM Modulation abgeschaltet, sendet das Instrument INT als Standardwert für den Befehl FM:STAT 1 (analog zur manuellen Bedienung). :FM:INTern:FREQuency <NUM> (5) :FM:INTern:FREQuency? (6) Befehlszeile (5) dient der FM Modulationsfrequenzeinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR1, NR2 oder NR3 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der Einheit Hz (z.B. 34000000 Hz für 34 MHz). Befehlszeile (6) dient der aktuellen FM Modulationsfrequenzabfrage. Das Instrument sendet einen NR3 Datenstring ohne Einheit. :FM:INTern:SHAPe SIN | SQR (7) :FM:INTern:SHAPe? (8) Die Befehlszeile (7) dient der Signalformeinstellung des in20 ternen FM Modulationssignals. Die Parameter sind: SIN für Sinussignal und SQR für Rechtecksignal. Befehlszeile (8) dient der aktuellen Signalformabfrage. Das Instrument antwortet mit dem entsprechenden Datenstring (z. B. SIN). :FM:STATe 0 | OFF | 1 | ON (9) :FM:STATe? (10) Befehlszeile (9) dient der FM Modulationswahl. Die Parameter 1 oder ON aktivieren die FM Modulation. Die Parameter 0 oder OFF deaktivieren die FM Modulation (wenn aktiviert). Befehlszeile (10) dient der aktuellen FM Modulationsabfrage. Das Instrument sendet 0 bei nicht aktivierter FM Modulation und sendet 1 bei aktivierter FM Modulation. :FM:EXTern:COUPling AC | DC (11) :FM:EXTern:COUPling? (12) Befehlszeile (11) dient der Auswahl der Eingangskopplungsart AC oder DC des externen Modulationssignals. Befehlszeile (12) dient der aktuellen EingangskopplungsartAbfrage. Das Instrument sendet den entsprechenden Datenstring (AC oder DC). Beispiele: FM:INT:FREQ 9E+3; SHAP SIN; DEV 150E+3; STAT ON 6.15 Befehle PM (Phasen-Modulation) Syntax: :PM[:DEViation] <NUM> (1) :PM[:DEViation]? (2) Befehlszeile (1) dient der PM Phasenhubeinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR2 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der Einheit. Ist die Auflösung <0.01 rad, wird der Wert zur nächst höheren Stelle hin aufgerundet. Befehlszeile (2) dient der aktuellen Hubabfrage. Das Instrument sendet einen NR2 Datenstring ohne Einheit. :PM:UNIT RAD | DEG (3) :PM:UNIT? (4) Befehlszeile (3) wählt die PM-Maßeinheit RADians oder DEGrees. Befehlszeile (4) dient der aktuellen Maßeinheitsabfrage. Das Instrument sendet den entsprechenden Datenstring (RAD oder DEG). Fernbedienung :PM:SOURce INTern | EXTern (5) :PM:SOURce? (6) Befehlszeile (5) dient der PM Referenzquellenwahl und aktiviert gleichzeitig die PM Modulation. Nur einer der beiden Parameter ist erforderlich: INTern aktiviert die interne Referenzquelle und EXTern aktiviert die externe Referenz. Befehlszeile (6) dient der aktuellen Referenzquellenabfrage. Das Instrument sendet den Datenstring INT oder EXT (nicht INTERN oder EXTERN), entsprechend der eingestellten Referenzquelle. Ist die PM Modulation abgeschaltet, sendet das Instrument INT als Standardwert für den Befehl PM:STAT 1 (analog zur manuellen Bedienung). :PM:INTern:FREQuency <NUM> (7) :PM:INTern:FREQuency? (8) Befehlszeile (7) dient der PM Modulationsfrequenzeinstellung. Der <NUM> Parameter ist ein bereichsspezifischer NR1,NR2 oder NR3 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Bezeichnung der Einheit Hz (z.B. 34000000 Hz für 34 MHz). Befehlszeile (8) dient der aktuellen PM Modulationsfrequenzabfrage. Das Instrument sendet einen NR3 Datenstring ohne Einheit. :PM:INTern:SHAPe SIN | SQR (9) :PM:INTern:SHAPe? (10) Befehlszeile (9) dient der Signalformeinstellung des internen PM Modulationssignals. Die Parameter sind: SIN für Sinussignal und SQR für Rechtecksignal. Befehlszeile (10) dient der aktuellen Signalformabfrage. Das Instrument antwortet mit dem entsprechenden Datenstring (z. B. SIN). :PM:STATe 0 | OFF | 1 | ON (11) :PM:STATe? (12) Befehlszeile (11) dient der PM Modulationswahl. Die Parameter 1 oder ON aktivieren die PM Modulation. Die Parameter 0 oder OFF deaktivieren die PM Modulation (wenn aktiviert). Befehlszeile (12) dient der aktuellen PM Modulationsabfrage. Das Instrument sendet 0 bei nicht aktivierter PM Modulation und sendet 1 bei aktivierter PM Modulation. :PM:EXTern:COUPling AC | DC (13) :PM:EXTern:COUPling? (14) Befehlszeile (13) dient der Auswahl der Eingangskopplungsart AC oder DC des externen Modulationssignals. Befehlszeile (14) dient der aktuellen EingangskopplungsartAbfrage. Das Instrument sendet den entsprechenden Datenstring (AC oder DC). Beispiel: :PM:UNIT DEG; DEV 120; INT:FREQ 1E+3; SHAP SIN; STATE 1; 6.16 Befehle FSK (FSK Modulation) Syntax: :FSKey:SOURce EXT (1) :FSKey:SOURce? (2) Befehlszeile (1) dient der Wahl der FSK Referenzquelle. Nur extern ist möglich. Befehlszeile (2) dient der aktuellen Referenzquellenabfrage. Das Instrument sendet den Datenstring EXT (nicht EXTERN). :FSKey:F0 <NUM>(3) :FSKey:F0 ?(4) :FSKey:F1 <NUM>(5) :FSKey:F1?(6) Die Befehlszeilen (3) und (5) dienen der FSK Frequenzeinstellung (F0 bzw. F1). Der <NUM> Parameter ist ein bereichsspezifischer NR1, NR2 oder NR3 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Einheit Hz. Die Befehlszeilen (4) und (6) dienen zur Abfrage der aktuellen FSK Modulationsfrequenzen (F0 bzw. F1). Das Instrument sendet einen NR3 Datenstring ohne Einheit. :FSKey:STATe: 0|OFF|1|ON (7) :FSKey:STATe?(8) Befehlszeile (7) dient der FSK Modulationswahl. Die Parameter 1 oder ON aktivieren die FSK Modulation. Die Parameter 0 und OFF deaktivieren die FSK Modulation (wenn aktiviert). Befehlszeile (8) dient der aktuellen FSK Modulationsabfrage. Das Instrument sendet 0 bei nicht aktivierter FSK Modulation bzw. 1 bei aktivierter FSK Modulation. Beispiel: FSK:SOUR EXT; F0 400E+6; F1 410E+6; STAT ON 6.17 Befehle PSK (PSK Modulation) Syntax: :PSKey:SOURce EXT (1) :PSKey:SOURce? (2) Befehlszeile (1) dient der Wahl der PSK Referenzquelle. Nur extern ist möglich. Befehlszeile (2) dient der aktuellen Referenzquellenabfrage. Das Instrument sendet den Datenstring EXT (nicht EXTERN). 21 Fernbedienung :PSKey:PH0 <NUM>(3) :PSKey:PH0 ?(4) :PSKey:PH1 <NUM>(5) :PSKey:PH1?(6) Die Befehlszeilen (3) und (5) dienen der PSK Phaseneinstellung (PH0 bzw. PH1). Der <NUM> Parameter ist ein bereichsspezifischer NR2 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring muss keine Einheit angefügt werden. Ist die Auflösung <0.01 rad, wird der Wert zur nächst höheren Stelle hin aufgerundet. Die Befehlszeilen (4) und (6) dienen zur Abfrage der aktuellen PSK Phasen (PH0 bzw. PH1). Das Instrument sendet einen NR2 Datenstring ohne Einheit. :PSKey:UNIT RAD|DEG(7) :PSKey:UNIT?(8) Befehlszeile (7) wählt die PSK-Maßeinheit RADians oder DEGrees. Befehlszeile (8) dient der aktuellen Maßeinheitsabfrage. Das Instrument sendet den entsprechenden Datenstring (RAD oder DEG). :PSKey:STATe: 0|OFF|1|ON (9) :PSKey:STATe?(10) Befehlszeile (9) dient der PSK Modulationswahl. Die Parameter 1 oder ON aktivieren die PSK Modulation. Die Parameter 0 und OFF deaktivieren die PSK Modulation (wenn aktiviert). Befehlszeile (10) dient der aktuellen PSK Modulationsabfrage. Das Instrument sendet 0 bei nicht aktivierter PSK Modulation bzw. 1 bei aktivierter PSK Modulation. Beispiel: :PSK:SOUR EXT; UNIT RAD; PH0 0; PH1 10; STAT ON 6.18 Befehle SWEEP (SWEEP Funktion) Syntax: :FREQuency:MODE SWEep (1) :FREQuency:MODE FIXed | CW (2) :FREQuency:MODE?(3) Mit Befehlszeile (1) wird die Sweepfunktion aktiviert. Mit Befehlszeile (2) kann die Sweepfunktion deaktiviert werden (wenn aktiviert). Mit Befehlszeile (3) wird der aktuelle Status der SweepFunktion abgefragt. Das Instrument sendet den Datenstring SWE, wenn die Sweepfunktion aktiviert ist, und FIX, wenn die Sweepfunktion deaktiviert ist. :FREQuency:STARt <NUM> (4) :FREQuency:STARt?(5) 22 :FREQuency:STOP <NUM> (6) :FREQuency:STOP?(7) Die Befehlszeilen (4) und (6) dienen der Einstellung der Frequenzen START und STOP. Der <NUM> Parameter ist ein bereichsspezifischer NR1, NR2 oder NR3 Datenstring (siehe Abschnitt Syntaxkonvention). Dem Datenstring folgt automatisch die Einheit Hz. Die Befehlszeilen (5) und (7) dienen der aktuellen Frequenzabfrage der Sweepfunktion (START bzw. STOP). Das Instrument sendet einen NR3 Datenstring ohne Einheit. :SWEep:TIME <NUM> (8) :SWEep:TIME?(9) Die Befehlszeile (8) dient zur Einstellung der Sweepzeit. Der <NUM> Parameter ist ein bereichsspezifischer NR2 Datenstring. Dem Datenstring folgt automatisch die Einheit sec. Befehlszeile (9) dient der Abfrage der aktuellen Sweepzeit. Das Instrument sendet einen NR2 Datenstring. Beispiel: :SWE:TIME 5; :FREQ:STAR 16E+6;:FREQ:STOP 1.2E+9; :FREQ:MODE SWE 6.19 Befehle SYSTEM Syntax: :SYSTem:ERRor? Diese Befehlszeile dient der Abfrage des aktuellen Fehlercodes. Wenn mehrere Fehler aufgetreten sind, wird der zuerst gemeldete Fehler gesendet und der Code nach Null zurückgesetzt. Beim Einschalten des Instruments werden alle Fehlercodes nach Null gesetzt. Die Bedeutung der einzelnen Fehlercodes ist im entsprechenden Abschnitt erläutert. Anmerkung zur Syntax Zu Beginn jeder Befehlszeile steht das „:“ Zeichen (Doppelpunkt). Es ist optional. Im Falle aufeinanderfolgender Befehle der gleichen Funktionsart, besteht die Möglichkeit der vereinfachten Befehlsschreibweise, wie im folgenden Beispiel gezeigt wird: Beispiel (Kürzung): FM:INT:FREQ 9E+3; SHAP SIN; DEV 150E+3; STAT ON entspricht der längeren Schreibweise: :FM:INT:FREQ 9E+3; :FM:INT:SHAP SIN; :FM:DEV 150E+3; STAT ON Da sich alle Befehle auf die Funktion FM beziehen, können die im Beispiel grau hinterlegten :FM entfallen. Gehört der nachfolgende Befehl zu einer anderen Gruppe (z.B. AM), muss dieser natürlich mit :AM beginnen. Fernbedienung 6.20 Bedeutung des Fehlercodes 00 Kein Fehler 01 Direct Digital Synthesis-Fehler (Hardware) 02 Interner Referenzfehler (Hardware) 03 Externer Referenzfehler (Hardware) 04 PLL1 Phase Look Loop Fehler (Hardware) 05 PLL2 Phase Look Loop Fehler (Hardware) 08 Kalibration Fehler 09 Überlast Fehler (Hardware) 15 Pegel Fehler (Bereichsüberschreitung) 16 (Träger) Frequenz Fehler (Bereichsüberschreitung) 21 AM Modulation aktiviert (eine andere Modulationsart kann nicht gewählt werden) 22 PM Modulation aktiviert (eine andere Modulationsart kann nicht gewählt werden) 23 FM Modulation aktiviert (eine andere Modulationsart kann nicht gewählt werden) 25 AM Modulationsgrad Fehler (Bereichsüberschreitung) 62 FM Frequenzhub Fehler (erlaubter Bereich: 2 kHz – 400 kHz) 63 FM Frequenzhub Fehler (erlaubter Bereich: 1 kHz – 200 kHz) 64 FM Frequenzhub Fehler (erlaubter Bereich: 200 Hz – 150 kHz) 70 AM Frequenzmodulation Fehler (erlaubter Bereich: 10 Hz – 20 kHz) 71 AM Frequenzmodulation Fehler (erlaubter Bereich: 10 Hz – 40 kHz) 75 PM Frequenzhub Fehler (bei Fernsteuerung, keine Phase < 0) 76 Frequenz Fehler (bei Fernsteuerung, keine Frequenz < 0) 81 FM oder PM Frequenzmodulation Fehler (erlaubter Bereich: 10 Hz – 20 kHz) 82 FM oder PM Frequenzmodulation Fehler (erlaubter Bereich: 10 Hz – 100 kHz) 90 PM Frequenzhub Fehler (erlaubter Bereich: 0 rad – 3.14 rad) 91 PM Frequenzhub Fehler (erlaubter Bereich: 0 rad – 10.00 rad) 92 PM Frequenzhub Fehler (erlaubter Bereich: 0 deg – 180.0 deg) 93 PM Frequenzhub Fehler (erlaubter Bereich: 0 deg – 573.0 deg) 102 Syntax oder Parameter Fehler (Fernsteuerung) 103 Ungültiges Trennzeichen (Fernsteuerung) 110 Befehlskopf (Header) Fehler (Fernsteuerung) 120 Numerische Daten Fehler (Fernsteuerung) 23 Technische Daten 7 Technische Technische Daten Daten 3 GHz HF-Synthesizer HM8135 3 GHz HF-Synthesizer HM8135 AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. 3 GHz HF-Synthesizer HM8135 AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. 3 GHz HF-Synthesizer 3 GHz HF-Synthesizer HM8135 AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. HM8135 Frequenz 3 GHz HF-Synthesizer HM8135 3 GHz HF-Synthesizer HM8135 AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. 1 Hz…3 GHz Frequenz Bereich: AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. 3 GHz HF-Synthesizer HM8135 Hz…3 GHz Bereich: 1 Hz Auflösung: AlleFrequenz Angaben bei 23 °C nach einer Aufwärmzeit von 30 Minuten. AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. 3 GHz HF-Synthesizer HM8135 Hz…3 Frequenz 1 Hz Bereich: Auflösung: <10 ms GHz Umschaltzeit: Frequenz 3 GHz HF-Synthesizer HM8135 AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. 1 Hz…3 Bereich: Hzms GHz <10 Auflösung: Umschaltzeit: Frequenz AlleAngabenbei23°CnacheinerAufwärmzeitvon30Minuten. Bereich 1ms Hz…3 1 Hz Auflösung: <10 Umschaltzeit: Hz…3 GHzGHz Frequenz Bereich: 10 MHz - Referenz <10 Umschaltzeit: 1 Hz…3 Bereich: Hz 10 MHz - Referenz Standard:TCXO Auflösung: Frequenz Auflösung 1ms Hz GHz 1 Hz Standard:TCXO Auflösung: Hz…3 10 MHz - Referenz Bereich: <10 ms GHz Temperaturstabilität Umschaltzeit: Frequenz Umschaltzeit <10 ms 10 MHz - Referenz ≤±0,5 ppm Frequenz <10 ms Standard:TCXO Temperaturstabilität Umschaltzeit: Hz Auflösung: (0…50°C): 1 Hz…3 GHz Bereich: 1≤±1 Hz…3 GHz ≤±0,5 ppm Standard:TCXO Bereich: Temperaturstabilität (0…50°C): <10 ms Umschaltzeit: Alterung: Hzppm/Jahr Auflösung: 10 MHz - Referenz 10 MHz - Referenz ≤±0,5 ppm 1≤±1 Hzppm/Jahr Temperaturstabilität Auflösung: Alterung: (0…50°C): 10 MHz - Referenz Option:OCXO (HO85) Standard:TCXO <10 ms Umschaltzeit: Temperaturstabilität Standard ≤±0,5 ppm TCXO; Option OCXO (HO85) <10 ms (0…50°C): Umschaltzeit: ≤±1 ppm/Jahr Alterung: Option:OCXO (HO85) Standard:TCXO Temperaturstabilität 10 MHz - Referenz ≤±1 ppm/Jahr Alterung: x 10-8ppm; Option:OCXO (HO85) ≤±0,5 ppm Temperaturstabilität Standard:TCXO (0…50°C): 10 MHz 0…50 °C - Referenz ≤±0,5 ≤±1 x 10-8 -8 -9 Option:OCXO (HO85) ≤±0,5 10 MHz - Referenz Temperaturstabilität (0…50°C): ≤±1≤±1 x ppm 10ppm/Jahr; /Tag ppm/Jahr Alterung: Standard:TCXO ≤±1 x 10-9/Tag Alterung -8 Standard:TCXO ≤±0,5 x ppm 10-9 /Tag ≤±1 ppm/Jahr (0…50°C):(HO85) Alterung: (Geräterückseite) Ausgang(interneReferenz): Option:OCXO Temperaturstabilität -8 Ausgang (interne Referenz) ≤±0,5 Temperaturstabilität ≤±1 ppm/Jahr x ppm 10-9/Tag (Geräterückseite) Alterung: Ausgang(interneReferenz): Option:OCXO (HO85) TTL Pegel: (0…50°C): -8/Tag ≤±0,5 ≤±1TTL x ppm 10-9 Alterung: (0…50°C): (Geräterückseite) TTL Ausgang(interneReferenz): Pegel: Temperaturstabilität Option:OCXO (HO85) Eingang(externeReferenz): ppm/Jahr Pegel -9 ≤±1 ppm/Jahr x 10-8 Ausgang(interneReferenz): Alterung: TTLdBm (Geräterückseite) Eingang(externeReferenz): (0…50°C): >0 Temperaturstabilität /Tag Pegel: Option:OCXO (HO85) Eingang (externe Referenz) 10 -8 -9 TTL Option:OCXO (HO85) (Geräterückseite) >0 dBm ≤±1MHz x 10±20 /Tag Eingang(externeReferenz): Pegel: Alterung: ppm Frequenz: (0…50°C): Ausgang(interneReferenz): Temperaturstabilität -8 -9 ppm (Geräterückseite) Eingang(externeReferenz): Temperaturstabilität >0 dBm 10 Pegel: Frequenz: Ausgang(interneReferenz): ≤±1 x dBm 10±20 /Tag TTLMHz Alterung: Pegel >0 (0…50°C): -8 -8 ppm -9 xx 10 >0 dBm Pegel: (0…50°C): 10 MHz TTL Frequenz: (Geräterückseite) Ausgang(interneReferenz): Eingang(externeReferenz): ≤±1 10±20 /Tag Alterung: Reinheit (ohne ≤±1 Spektrale Modulation) Frequenz 10 MHz ±20 ppm -9 -9/Tag 10 MHz ppm xdBc 10±20 Frequenz: Alterung: (Geräterückseite) Eingang(externeReferenz): TTL ≤-35 Spektrale Reinheit (ohne ≤±1 Modulation) >0 dBm Harmonische: Pegel: Ausgang(interneReferenz): Spektrale (ohne Modulation) (Geräterückseite) Ausgang(interneReferenz): ≤-35 >0 dBm Harmonische: Pegel: Reinheit Spektrale Reinheit (ohne Modulation) ≤-50 dBc±20 (>15 kHz vom Träger) 10 MHz ppm Eingang(externeReferenz): Unharmonische: Frequenz: TTL Pegel: ≤-35 Spektrale Reinheit (ohne TTL Modulation) (>15 kHz<-35 vomdBc) Träger) 10 MHz ppm Harmonische: Unharmonische: Frequenz: >0 dBm ≤-50 dBc±20 Subharmonische: (Geräterückseite) Eingang(externeReferenz): Harmonische ≤-30 dBc (typ. ≤-35 Harmonische: Eingang(externeReferenz): (>15 kHz vom Träger) ≤-50 dBc Unharmonische: Subharmonische: 10 MHz ±20 ppm (bei 20 kHz vom Träger) Frequenz: Phasenrauschen: >0 dBm Pegel: Spektrale Reinheit (ohne (Geräterückseite) Modulation) Unharmonische ≤-50 dBc (>15 kHz Träger) ≤-50 dBc (>15 kHz vomvom Träger) dBm Unharmonische: Pegel: (bei 20 kHz vom Träger) Subharmonische: Phasenrauschen: ≤-120 dBc/Hz ≤-35 Spektrale Reinheit (ohne >0 Modulation) f<16MHz: Harmonische: 10 MHz ±20 ppm Frequenz: ≤-50 dBc MHz ±20 ppm Subharmonische: Frequenz: (bei 20 kHz vom Träger) ≤-120 dBc/Hz ≤-35 Phasenrauschen: f<16MHz: Harmonische: ≤-95 dBc/Hz (>15 kHz vom Träger) 16MHz≤f<250MHz: Unharmonische: Spektrale Reinheit (ohne 10 Modulation) Subharmonische: <2,1 GHz ≤-50 dBc (bei 20 kHz vom Träger) Phasenrauschen: ≤-120 ≤-95 dBc/Hz ≤-50 dBc (>15 kHz vom Träger) f<16MHz: 16MHz≤f<250MHz: Unharmonische: ≤-35 dBc/Hz Harmonische: 250MHz≤f<500MHz: Subharmonische: Spektrale Reinheit (ohne ≤-105 Modulation) Subharmonische: >2,1 GHz ≤-43 dBc (typ. -47dBc) ≤-120 f<16MHz: Reinheit ≤-95 dBc/Hz ≤-105 Spektrale (ohne ≤-100 Modulation) ≤-50 dBc 16MHz≤f<250MHz: 250MHz≤f<500MHz: Subharmonische: (>15 kHz vom Träger) dBc/Hz (bei 20 kHz vom Träger) Unharmonische: 500MHz≤f<1000MHz: Phasenrauschen: ≤-35 Harmonische: ≤-95 dBc/Hz ≤-35 dBc 16MHz≤f<250MHz: Harmonische: ≤-105 ≤-100 dBc/Hz (bei 20 kHz vom Träger) 250MHz≤f<500MHz: 500MHz≤f<1000MHz: Phasenrauschen: Phasenrauschen (bei 20(>15 kHz vom Träger) ≤-120 Subharmonische: 1GHz≤f<2GHz: f<16MHz: ≤-50 kHz vom Träger) Unharmonische: ≤-105 ≤-50 dBc (>15 kHz vom Träger) 250MHz≤f<500MHz: Unharmonische: ≤-100 dBc/Hz ≤-95 ≤-120 500MHz≤f<1000MHz: 1GHz≤f<2GHz: f<16MHz: (bei 20 kHz vom Träger) ≤-90 dBc/Hz Phasenrauschen: 2GHz≤f<3GHz: 16MHz≤f<250MHz: Subharmonische: f <16 MHz ≤-120 dBc/Hz ≤-100 dBc/Hz ≤-50 dBc 500MHz≤f<1000MHz: Subharmonische: ≤-95 ≤-90 dBc/Hz 1GHz≤f<2GHz: 2GHz≤f<3GHz: 16MHz≤f<250MHz: ≤-120 typ. <4 Hz; ≤6,5 (0,3…3 kHz Bandbreite) ≤-105 f<16MHz: Stör-FM: 250MHz≤f<500MHz: (bei 20 kHz vomHz Träger) Phasenrauschen: 162GHz≤f<3GHz: MHz ≤f <250 MHz ≤-95 dBc/Hz ≤-95 (bei 20 kHz vom Träger) 1GHz≤f<2GHz: Phasenrauschen: ≤-90 dBc/Hz <4 Hz; Hz (0,3…3 Bandbreite) ≤-105 dBc/Hz Stör-FM: 250MHz≤f<500MHz: typ. <0,06 %≤6,5 (0,03…20 kHzkHz Bandbreite) ≤-100 16MHz≤f<250MHz: Stör-AM: 500MHz≤f<1000MHz: ≤-120 f<16MHz: ≤-90 dBc/Hz ≤-120 dBc/Hz 2GHz≤f<3GHz: f<16MHz: <4 Hz;dBc/Hz Hz (0,3…3 Bandbreite) typ. <0,06 %≤6,5 (0,03…20 kHzkHz Bandbreite) ≤-100 Stör-FM: Stör-AM: 500MHz≤f<1000MHz: ≤-105 250MHz≤f<500MHz: 1GHz≤f<2GHz: ≤-95 16MHz≤f<250MHz: 250 MHz ≤f <500 MHz ≤-105 <4 Hz;%≤6,5 Hz (0,3…3 Bandbreite) dBc/Hz Stör-FM: 16MHz≤f<250MHz: typ. <0,06 (0,03…20 kHzkHz Bandbreite) Stör-AM: 1GHz≤f<2GHz: ≤-100 ≤-90 500MHz≤f<1000MHz: ≤-95 2GHz≤f<3GHz: ≤-105 dBc/Hz 250MHz≤f<500MHz: 500 MHz ≤f <1.000 MHz ≤-100 dBc/Hz typ. (0,03…20 kHzkHz Bandbreite) ≤-105 dBc/Hz Stör-AM: 250MHz≤f<500MHz: ≤-90 dBc/Hz 2GHz≤f<3GHz: ≤-95<0,06 <4 Hz;%≤6,5 Hz (0,3…3 Bandbreite) 1GHz≤f<2GHz: Stör-FM: ≤-100 500MHz≤f<1000MHz: ≤-100 dBc/Hz 500MHz≤f<1000MHz: <4 Hz; Hz (0,3…3 Bandbreite) Stör-FM: ≤-90 typ. <0,06 %≤6,5 (0,03…20 kHzkHz Bandbreite) 2GHz≤f<3GHz: Stör-AM: ≤-95 dBc/Hz 1GHz≤f<2GHz: 1 GHz ≤f <2 GHz ≤-95 dBc/Hz ≤-95 dBc/Hz 1GHz≤f<2GHz: typ. (0,03…20 kHzkHz Bandbreite) Stör-AM: <4 Hz;%≤6,5 Hz (0,3…3 Bandbreite) Stör-FM: ≤-90<0,06 2GHz≤f<3GHz: 2 GHz ≤f <3 GHz ≤-90 dBc/Hz ≤-90 dBc/Hz 2GHz≤f<3GHz: typ. <4 <0,06 (0,03…20 kHzkHz Bandbreite) Stör-AM: Hz;%≤6,5 Hz (0,3…3 Bandbreite) Stör-FM: typ.typ. <4 Hz; ≤6,5 Hz (0,3…3 kHz Bandbreite) Stör-FM: Stör-FM <4% Hz; ≤6,5 HzkHz (0,3…3 kHz Bandbreite) <0,06 (0,03…20 Bandbreite) Stör-AM: typ. <0,06 % (0,03…20 kHz Bandbreite) Stör-AM: Stör-AM <0,06 % (0,03…20 kHz Bandbreite) (Typisches Phasenrauschen bei 1 GHz) (Typisches Phasenrauschen bei 1 GHz) (Typisches Phasenrauschen bei 1 GHz) Ausgangspegel (Typisches Phasenrauschen bei-135…+13 1 GHz) dBm Ausgangspegel Bereich: -135…+13 dBm Bereich: Ausgangspegel dB (Typisches Phasenrauschen bei0,1 1 GHz) Auflösung: -135…+13 dBm Ausgangspegel 0,1 dB dB (Typisches Phasenrauschen bei0,0…30,0 1 GHz) Bereich: Auflösung: in 0,1 dB Schritten Anzeige-Offsetfürext.Attn.: -135…+13 dBm Bereich: 0,1 dB dB in 0,1 dB Schritten Auflösung: Anzeige-Offsetfürext.Attn.: (Typisches Phasenrauschen bei0,0…30,0 1 GHz) Fehlerf<1,5GHz;Pegel>-120dBm Ausgangspegel 0,1 dBdB dB Auflösung: in 0,1 dB Schritten Anzeige-Offsetfürext.Attn.: Fehlerf<1,5GHz;Pegel>-120dBm für Pegel >-57 dBm: ≤±0,5 -135…+13 dBm Ausgangspegel Bereich: (Typisches Phasenrauschen bei0,0…30,0 GHz) Typisches Phasenrauschen bei 11GHz in 0,1 dB Schritten (Typisches Phasenrauschen bei0,0…30,0 1 GHz) Anzeige-Offsetfürext.Attn.: >-57 dBm: ≤±0,5 -135…+13 Fehlerf<1,5GHz;Pegel>-120dBm Bereich: für Pegel <-57 ≤±(0,5 dBdB +dBm (0,2 x (-57 dBm - Pegel))/10) 0,1 dBdB Auflösung: Ausgangspegel Ausgangspegel Fehlerf<1,5GHz;Pegel>-120dBm >-57 dBm: ≤±0,5 für Pegel <-57 ≤±(0,5 dBdB +dBm (0,2 x (-57 dBm - Pegel))/10) 0,1 dBdB Auflösung: -135…+13 0,0…30,0 in 0,1 dB Schritten Bereich: Fehlerf>1,5GHz;Pegel>-120dBm Anzeige-Offsetfürext.Attn.: Ausgangspegel Bereich >-57 dBm: ≤±0,5 für Pegel <-57 ≤±(0,5 dBdB +dBm (0,2 x (-57 dBm - Pegel))/10) Ausgangspegel 0,0…30,0 indBm 0,1 dB Schritten Fehlerf>1,5GHz;Pegel>-120dBm Anzeige-Offsetfürext.Attn.: 0,1-135…+13 dBdB ≤±0,7 Auflösung: Fehlerf<1,5GHz;Pegel>-120dBm -135…+13 Bereich: für Pegel <-57 ≤±(0,5 dBdB (0,2 (-57 dBm--Pegel))/10) Pegel))/10) -135…+13 Bereich: >-57 dBm: ≤±0,7 Fehlerf>1,5GHz;Pegel>-120dBm Fehlerf<1,5GHz;Pegel>-120dBm 0,0…30,0 in 0,1 dB dBm Schritten ≤±(0,7dB ++dBm (0,5 xx (-57 ≤±0,5 Anzeige-Offsetfürext.Attn.: 0,1 dBdB Auflösung: Auflösung 0,1 dB 0,1 Fehlerf>1,5GHz;Pegel>-120dBm Auflösung: ≤±0,7 <-57 dBm: ≤±(0,7dB ++ (0,5 xx (-57 für Pegel >-57 ≤±0,5 50 ΩdBdB ≤±(0,5 dBdB (0,2 (-57 dBm--Pegel))/10) Pegel))/10) Fehlerf<1,5GHz;Pegel>-120dBm Impedanz: 0,0…30,0 in 0,1 dB dBm Schritten Anzeige-Offsetfürext.Attn.: Anzeige-Offset fürdBm: ext. Attn. 0,0…30,0 0,0…30,0 dB≤1,5 0,1dBm dB Schritten für Pegel <-57 >-57 ≤±0,7 dB in 0,1 dB Schritten Anzeige-Offsetfürext.Attn.: ≤±(0,7dB ++ (0,5 xxin(-57 --Pegel))/10) ≤±(0,5 dBdB (0,2 (-57 dBm Pegel))/10) Impedanz: ≤±0,5 f50 ≤1Ω GHz: Stehwellenverhältnis: Fehlerf>1,5GHz;Pegel>-120dBm Fehlerf<1,5GHz;Pegel>-120dBm <-57 dBm: ≤±(0,7dB xx (-57 Fehlerf<1,5GHz;Pegel>-120dBm ≤1ΩGHz: ≤1,5 Fehler Impedanz: Stehwellenverhältnis: Fehlerf>1,5GHz;Pegel>-120dBm ≤±(0,5 dB ++ (0,5 (0,2≤2,5 (-57dBm dBm--Pegel))/10) Pegel))/10) f50 >1 ≤±0,7 für Pegel >-57 ≤±0,5 dB für GHz; PegelPegel >-57 dBm: dBm ≤±0,5 dB Impedanz: ≤1ΩGHz: ≤1,5 f50 >1 ≤±0,7 Stehwellenverhältnis: ≤±(0,7dB xx (-57 Fehlerf>1,5GHz;Pegel>-120dBm f <1,5 <-57 >-120 ≤±(0,5 dB ++ (0,5 (0,2≤2,5 (-57dBm dBm--Pegel))/10) Pegel))/10) ≤1Ω ≤1,5 Pegel <-57 dBm: ≤±(0,5 dB dB (0,2≤2,5 Stehwellenverhältnis: f≤±(0,7dB >1 GHz: ++ (0,5 xx (-57 >-57 ≤±0,7 dB 50 Impedanz: Fehlerf>1,5GHz;Pegel>-120dBm Modulationsquellen (-57dBm dBm--Pegel))/10) Pegel))/10) fürfür Pegel >-57 dBm ≤±0,5 f50 >1 GHz: Fehlerf>1,5GHz;Pegel>-120dBm Ω Impedanz: <-57 ≤±(0,7dB (0,5 x (-57 dBmdBm - Pegel))/10) 10 kHz Sinus, ≤1Hz…200 ≤1,5 Intern: Stehwellenverhältnis: für Pegel >-57 dBm: ≤±0,7 dB +dB fürModulationsquellen Pegel <-57 dBm ≤±(0,5 +≤2,5 (0,2 x (-57 - Pegel))/10) für Pegel >-57 ≤±0,7 dB +kHz Hz…200 kHz Sinus, f≤±(0,7dB ≤1,5 Intern: Stehwellenverhältnis: 50≤1 ΩGHz: Modulationsquellen 10 Dreieck, Sägezahn Impedanz: >1Hz…20 ≤2,5 <-57 dBm: (0,5Rechteck, x (-57 dBm - Pegel))/10) Fehler für PegelPegel <-57 >-120 dBm: dBm ≤±(0,7dB (0,5Rechteck, x (-57 dBm - Pegel))/10) Hz…200 kHz Sinus, Modulationsquellen Hz…20 Dreieck, Sägezahn Intern: f50>1 ≤2,5 ≤1Hz ≤1,5 10 Stehwellenverhältnis: Auflösung: ΩGHz: +kHz Impedanz: f >1,5 GHz; Hz…200 kHzRechteck, Sinus, Dreieck, Sägezahn 50 Ω Intern: Impedanz: 10 Hz Hz…20 kHz Eingang >1 ≤2,5 Extern: f ≤1 GHz:Frontplatte ≤1,5 Stehwellenverhältnis: Modulationsquellen fürAuflösung: Pegel >-57 dBm ≤±0,7 dB Hz…20 kHz Rechteck, Dreieck, Sägezahn fEingang GHz: ≤1,5 Stehwellenverhältnis: 10≤1 Frontplatte Auflösung: Extern: kΩ II 50 pF Hz…200 kHz Sinus, Modulationsquellen Intern: >1Hz fürImpedanz: Pegel <-57 dBm ≤±(0,7 dB +≤2,5 (0,5 x (-57 dBm - Pegel))/10) Hz Auflösung: f10 ≤2,5 Eingang Frontplatte II 50 pF Hz…200 kHzRechteck, Sinus, Dreieck, Sägezahn Extern: Impedanz: Intern: 2 >1 VkΩ für Bereichsendwert Eingangspegel: Hz…20 kHz Modulationsquellen SSGHz: Impedanz 50 Ω Eingang Frontplatte Extern: 10 II 50 pF 2 VkΩ für Bereichsendwert Impedanz: Eingangspegel: Hz…20 kHz Hz…200 kHzRechteck, Sinus, Dreieck, Sägezahn AC oder DC Hz Intern: Kopplung: Auflösung: SS Modulationsquellen 10 kΩ II 50 pF Impedanz: 2 V für Bereichsendwert AC oder DC Modulationsquellen Hz Eingangspegel: Kopplung: Auflösung: Hz…20 kHz Frontplatte Eingang Frontplatte Ausgang: Extern: Hz…200 kHzRechteck, Sinus, Dreieck, Sägezahn Intern: SS Stehwellenverhältnis f ≤1 GHz ≤1,5 Technische Daten Technische Daten 2 VHz…200 für Bereichsendwert 10 kHzRechteck, Sinus, Dreieck, Sägezahn Eingangspegel: Intern: AC oder DC Eingang Frontplatte Kopplung: Ausgang: Extern: Hz kΩ II 50 pF Auflösung: Pegel: Impedanz: SS Hz…20 kHz SS f >1 GHzFrontplatte ≤2,5 AC oder DC 10 kHz Kopplung: Frontplatte 2 VHz…20 kΩ II 50 pF Rechteck, Dreieck, Sägezahn Ausgang: Pegel: Eingang Frontplatte 1 kΩ Extern: für Bereichsendwert Impedanz: Eingangspegel: Hz Auflösung: SS Frontplatte 10 Ausgang: Auflösung: 2 VHz 1 kΩ für Bereichsendwert Pegel: Impedanz: Eingangspegel: kΩ II 50 pF AC oder DC Kopplung: Eingang Frontplatte Extern: SS 2 VkΩ Eingang Frontplatte Pegel: Extern: 1 kΩ AC oder DC Impedanz: Kopplung: für Bereichsendwert Eingangspegel: Frontplatte SS Ausgang: 10 II 50 pF 24 1 kΩ 10 II 50 pF Impedanz: Frontplatte Ausgang: AC oder DC Kopplung: Pegel: 2 VkΩ für Bereichsendwert Eingangspegel: SS 2AC VkΩ für Bereichsendwert Eingangspegel: Pegel: Frontplatte 1 Ausgang: Impedanz: SS oder DC Kopplung: SS AC Kopplung: 1 Impedanz: 2 kΩ VSSoder DC Pegel: Frontplatte Ausgang: Modulationsquellen Amplitudenmodulation (Pegel ≤+7 dBm) 10 Hz…200 kHz (Pegel Sinus, Intern intern oder extern Amplitudenmodulation ≤+7 dBm) Quelle: 10 Hz…20 kHz (Pegel Rechteck, Dreieck, Sägezahn intern oder extern Quelle: Amplitudenmodulation ≤+7 0…100 % dBm) Modulationsgrad: intern oder extern Amplitudenmodulation (Pegel 0…100 % dBm) Quelle: Modulationsgrad: 0,1 % ≤+7 Auflösung: Auflösung 10 Hz intern oder extern Quelle: 0…100 % angezeigten 0,1 %des Modulationsgrad: Auflösung: ±4 % Wertes Genauigkeit: Amplitudenmodulation (Pegel ≤+7 dBm) T%% e%des coder hangezeigten n extern i s c ≤80 h e% Wertes Dund a tfMod e n≤50 kHz) 0…100 % Modulationsgrad: Extern (Eingang frontseitig) 0,1 ±4 Auflösung: Genauigkeit: ±0,5 (AM-Grad intern Amplitudenmodulation (Pegel ≤+7 dBm) Quelle: 0,1 % ≤+7 Auflösung: ±4 % ±0,5 (AM-Grad und fMod ≤50 kHz) intern oder extern Genauigkeit: Quelle: 10 Hz…100 kHz AC%Wertes 0…100 % Ext.Frequenzgang(bis-1dB): Modulationsgrad: Amplitudenmodulation (Pegel dBm) Impedanz 10%des kΩ IIangezeigten 50 pFbei≤80 ±4 % angezeigten Wertes Genauigkeit: ±0,5 (AM-Grad ≤80 undfMod fMod≤1≤50 10 Hz…100 kHz bei AC kHz) 0…100 % Ext.Frequenzgang(bis-1dB): Modulationsgrad: intern oder extern <2 (AM-Grad ≤60 %%und kHz) 0,1 %%des Quelle: Verzerrungen: Auflösung: Amplitudenmodulation (Pegel ≤+7 dBm) für Bereichsendwert Eingangspegel 2%% Vdes SS ±0,5 (AM-Grad ≤80 undf<20 fMod≤1 ≤50 kHz) 10 Hz…100 kHz bei AC <2 ≤60 %%und kHz) Amplitudenmodulation (Pegel ≤+7 dBm) 0,1 Ext.Frequenzgang(bis-1dB): Verzerrungen: Auflösung: 0…100 % ±4 % angezeigten Wertes <6 (AM-Grad ≤80 %, fMod kHz) Modulationsgrad: Genauigkeit: intern oder extern Quelle: Mod 10 Hz…100 kHz bei AC intern oder extern Ext.Frequenzgang(bis-1dB): Quelle: <2 ≤60 %%und kHz) ±4 angezeigten Wertes <6 (AM-Grad ≤80 %, fMod kHz) Verzerrungen: Genauigkeit: 0,1% %%des Auflösung: ±0,5 (AM-Grad ≤80 undf<20 fMod≤1 ≤50 kHz) 0…100 % Modulationsgrad: Mod Kopplung AC oder DC <2 % (AM-Grad ≤60 %%und kHz) 0…100 % Verzerrungen: Modulationsgrad: <6 ≤80 %, fMod kHz) ±0,5 (AM-Grad ≤80 undf<20 fMod≤1 ≤50 kHz) ±4 angezeigten Wertes Genauigkeit: 10 Hz…100 kHz bei AC Mod Ext.Frequenzgang(bis-1dB): 0,1 %%des Auflösung: Frequenzmodulation Ausgang (frontseitig) 0,1 %%des <6 (AM-Grad ≤80 %, fMod kHz) Auflösung: 10 Hz…100 kHz bei AC Ext.Frequenzgang(bis-1dB): ±0,5 (AM-Grad ≤80 undf<20 fMod≤1 intern oder extern ≤50 kHz) Frequenzmodulation <2 % ≤60 %%und kHz) Quelle: Verzerrungen: ±4 angezeigten Wertes Genauigkeit: Mod ±4 des angezeigten Wertes Genauigkeit: intern oder extern <2 (AM-Grad ≤60 % kHz) Quelle: Verzerrungen: 10 % Hz…100 kHz bei AC Frequenzmodulation ±200 kHz Ext.Frequenzgang(bis-1dB): <6 ≤80 %,%und fMod kHz) Hub: ±0,5 (AM-Grad ≤80 undf<20 fMod≤1 ≤50 kHz) Pegel 2% VHz…400 Mod SS ±0,5 (AM-Grad ≤80 undf<20 fMod ≤50 kHz) intern oder extern Frequenzmodulation ±200 Hz…400 kHz Quelle: <6 %% (AM-Grad ≤80 %, fMod kHz) Hub: <2 Hz…100 ≤60 %%und ≤1 kHz) (abhängig vom Frequenzband) Verzerrungen: 10 kHz bei AC Ext.Frequenzgang(bis-1dB): Mod Mod Impedanz 1 kΩ intern odervom extern 10 kHz bei Quelle: Ext.Frequenzgang(bis-1dB): ±200 Hz…400 kHz (abhängig Frequenzband) Hub: 100 <6 Hz…100 ≤80AC %,und fMod f<20 kHz) Auflösung: <2 %Hz (AM-Grad ≤60 % kHz) Verzerrungen: Frequenzmodulation Mod ≤1 Amplitudenmodulation -30 . . .+7dBm) ±200 Hz…400 kHz <2 (AM-Grad ≤60 und ≤1 kHz) Hub: Verzerrungen: (abhängig 100 vom Frequenzband) Auflösung: ±3 %Hz + restliche FM% (fMod kHz) intern oder extern Frequenzmodulation (Pegel Genauigkeit: Quelle: Mod <6 ≤80 %, fMod≤5f<20 kHz) Mod (abhängig vom Frequenzband) <6 (AM-Grad ≤80 fMod kHz) 100 Hz ±3 % + restliche FM%, (f ≤5<20 kHz) intern oder extern Auflösung: Genauigkeit: Quelle: ±200 Hz…400 kHz ±7 (5Mod kHz <f <100 kHz) Hub: Frequenzmodulation Mod Mod Quelle intern oder extern 100 Auflösung: ±3 %Hz + oder restliche FM (f ≤5<f kHz) ±200 Hz…400 kHz ±7 (5Mod kHz Genauigkeit: Hub: intern extern Quelle: (abhängig vom Frequenzband) Ext.Frequenzgang:(bis-1dB) Frequenzmodulation Mod <100 kHz) Modulationsgrad 0…100 % ±3 % + oder restliche FM (f ≤5<f kHz) Genauigkeit: ±7 (5Mod kHz Frequenzmodulation (abhängig vom Frequenzband) Ext.Frequenzgang:(bis-1dB) ±200 Hz…400 kHz 0…100 kHz 100 Hz Hub: DC-Kopplung: Auflösung: intern extern Quelle: Mod <100 kHz) intern oder extern ±7 % +% restliche FM (5 kHz Quelle: 0…100 kHz 100 Hz Ext.Frequenzgang:(bis-1dB) DC-Kopplung: Auflösung: (abhängig vom Frequenzband) Hz…100 kHz ±3 (fMod ≤5<f kHz) AC-Kopplung: Genauigkeit: Mod <100 kHz) ±200 Hz…400 kHz Hub: Auflösung 0,1 ±200 Hz…400 kHz Ext.Frequenzgang:(bis-1dB) Hub: 0…100 kHz 100 kHz ±3 +für restliche FM ≤5 kHz) DC-Kopplung: AC-Kopplung: Genauigkeit: Hz <1 Hub ≥50 kHz(f bei 1 <f kHz Auflösung: ±7 %Hz…100 (5Mod kHz Verzerrungen: (abhängig vom Frequenzband) Mod <100 kHz) 1 kHz, f>16 MHz Genauigkeit ±5 % @ f mod 0…100 kHz (abhängig vom Frequenzband) DC-Kopplung: Hz…100 kHz <1 ≥50 bei 1 <f kHz AC-Kopplung: ±7 +für restliche FM kHz Verzerrungen: ±3 %Hz (fMod ≤5 kHz) <3 Hub ≥10 kHz(5 Genauigkeit: Ext.Frequenzgang:(bis-1dB) 100 Auflösung: Mod <100 kHz) Hz…100 Hz Auflösung: <1 ≥50 bei 1 <f kHz <3 % HubkHz ≥10 kHz Verzerrungen: Ext.Frequenzgang:(bis-1dB) ±7 (5Mod kHz Ext.AC-Kopplung: Frequenzgang (bis -1 dB) 100 10 Hz…100 kHz bei AC≤5 0…100 kHz DC-Kopplung: ±3 +für restliche FM (f kHz) Genauigkeit: Mod <100 kHz) <1 ≥50FM bei 1 <f kHz ±3 +für restliche ≤5 kHz) Verzerrungen: Genauigkeit: <3 HubkHz ≥10 kHz(f 0…100 kHz DC-Kopplung: 100%Hz…100 Ext.Frequenzgang:(bis-1dB) AC-Kopplung: ±7 (5Mod kHz Phasenmodulation Mod <100 kHz) Mod ≤1 kHz) Verzerrungen <2 % (AM-Grad ≤60 %; f mod <3 Hubextern ≥10 kHz(5bei ±7 %Hz…100 +für restliche kHz1<f <100 kHz) 100 kHz AC-Kopplung: 0…100 kHz intern oder Phasenmodulation <1 ≥50FM kHz DC-Kopplung: Quelle: Verzerrungen: Mod Ext.Frequenzgang:(bis-1dB) Mod <6 % (AM-Grad ≤80 fmod <20 kHz) Ext.Frequenzgang:(bis-1dB) intern oder <1 für Hubextern ≥50 bei%;1 kHz Quelle: Verzerrungen: 100% Hz…100 kHz Phasenmodulation AC-Kopplung: <3 ≥10 kHz Hub: 0…100 kHz DC-Kopplung: 0…100 kHz DC-Kopplung: intern oder Phasenmodulation Quelle: <3 für Hubextern ≥10 Hub: <1 %Hz…100 ≥50 kHz bei 1 kHz <16 MHz: 0…3,14 rad Verzerrungen: 100 kHz AC-Kopplung: Frequenzmodulation intern oder extern 100 Quelle: AC-Kopplung: <16 0…3,14 rad Hub: >16 MHz: 0…10 <3 %Hz…100 rad ≥10 kHz bei 1 kHz <1 für HubkHz ≥50 Verzerrungen: Phasenmodulation Quelle intern oder extern <1 % für Hub ≥50 kHz bei 1 kHz Hub: Verzerrungen: <16 0…3,14 rad >16 MHz: 0…10 rad 0,01 rad intern oder extern Phasenmodulation Auflösung: Quelle: <3 ≥10 <16 0…3,14 rad <3 für Hub ≥10 kHz >16 MHz: 0…10 rad 0,01 rad intern oder extern Auflösung: Quelle: ±5 % bis 1 kHz + restliche PM Genauigkeit: Hub: Phasenmodulation Hub ±200 Hz…400 kHz >16 0…10 rad 0,01 rad ±5 % bis 1 kHz + restliche PM Auflösung: Genauigkeit: Hub: intern oder extern <16 MHz: 0…3,14 rad Quelle: Ext.Frequenzgang:(bis-1dB) Phasenmodulation (abhängig vom Frequenzband) 0,01 Auflösung: ±5 %rad bis 1 kHz + restliche PM <16 0…3,14 rad Genauigkeit: Ext.Frequenzgang:(bis-1dB) 0…100 kHz >16 MHz: 0…10 rad Hub:Phasenmodulation DC-Kopplung: intern oder extern Quelle: ±5 % bis 1 kHz intern oder extern Genauigkeit: Quelle: 0…100 kHz >16 0…10 rad Ext.Frequenzgang:(bis-1dB) Auflösung 100 Hz DC-Kopplung: <16 MHz: 0…3,14 rad 100 Hz…100 kHz+ restliche PM 0,01 rad AC-Kopplung: Auflösung: Hub: Ext.Frequenzgang:(bis-1dB) Hub: 0…100 kHz 100 Hz…100 kHz 0,01 rad DC-Kopplung: AC-Kopplung: Auflösung: >16 MHz: 0…10 rad <3 bei = 1+ kHz und(fmod Hub = 10 rad ±5 % bis 1fMod kHz restliche PM≤5 Verzerrungen: Genauigkeit: <16 0…3,14 rad Genauigkeit kHz) ±3 % + restliche FM 0…100 kHz <16 MHz: 0…3,14 rad DC-Kopplung: 100 Hz…100 kHz <3 bei = 1+ kHz und(5Hub rad ±5 % bis 1fMod kHz restliche PM =<f10 AC-Kopplung: Verzerrungen: Genauigkeit: 0,01 rad Auflösung: Ext.Frequenzgang:(bis-1dB) >16 0…10 rad ±7 % + restliche FM kHz mod 100 Hz…100 kHz >16 MHz: 0…10 rad AC-Kopplung: <3 bei = 1+ kHz und Hub Verzerrungen: Ext.Frequenzgang:(bis-1dB) ±5 % bis 1fMod kHz restliche PM = 10 rad 0…100 kHz Genauigkeit: DC-Kopplung: 0,01 rad Auflösung: FSK - Modulation <100 kHz) <3 bei = 1+ kHz und Hub rad Verzerrungen: Auflösung: 0…100 kHz DC-Kopplung: 16 GHz 100MHz…3 kHz - Modulation Ext.Frequenzgang:(bis-1dB) Bereich(F1…F0): AC-Kopplung: ±5 %Hz…100 bis 1fMod kHz restliche PM = 10 rad Genauigkeit: Ext.FSK Frequenzgang (bis -1 dB) 0,01 ±5 % bis 1fMod kHz restliche PM = 10 rad Genauigkeit: 16 MHz…3 GHz 100 Hz…100 kHz Bereich(F1…F0): AC-Kopplung: 0…100 kHz FSK - Modulation 2 <3FSK-Ebenen bei =+ 1 kHz und Hub DC-Kopplung: Betriebsart: Verzerrungen: Ext.Frequenzgang:(bis-1dB) DC-Kopplung 0…100 kHz Ext.Frequenzgang:(bis-1dB) 16 MHz…3 GHz FSK - Modulation 2 FSK-Ebenen <3 % bei fMod = 1 kHz und Hub = 10 rad Bereich(F1…F0): Betriebsart: Verzerrungen: 100 Hz…100 kHz extern AC-Kopplung: Datenquelle: 0…100 kHz DC-Kopplung: 16 MHz…3 GHz 0…100 kHz Bereich(F1…F0): DC-Kopplung: 2 extern Betriebsart: Datenquelle: <3FSK-Ebenen % bei fMod = 1kHz kHz und Hub = 10 rad 10 kbit/s Verzerrungen: Max.Hub: 100 Hz…100 kHz AC-Kopplung: FSK - Modulation AC-Kopplung 100 Hz…100 2 100 kHz Betriebsart: AC-Kopplung: extern 10 kbit/s Datenquelle: Max.Hub: 0…10 MHzfMod 16 MHz…3 GHz FSK - Modulation Shift(F1…F0): Bereich(F1…F0): <3FSK-Ebenen %Hz…100 bei = 1 kHz und Hub = 10 rad Verzerrungen: Verzerrungen <1 % für Hub ≥50und kHz Hub bei 1=kHz extern <3 %Hz bei fMod = 1 kHz 10 rad Datenquelle: Verzerrungen: 10 kbit/s 0…10 MHz 16 MHz…3 GHz Max.Hub: Shift(F1…F0): Bereich(F1…F0): 100 2 FSK-Ebenen Auflösung: Betriebsart: FSK - Modulation Mod <3 % für Hub ≥10 kHz 10 kbit/s Max.Hub: 0…10 MHz 100 Hz 2 FSK-Ebenen Shift(F1…F0): Auflösung: Betriebsart: 16 MHz…3 GHz siehe unter FM extern Bereich(F1…F0): Genauigkeit: Datenquelle: FSK - Modulation 0…10 Shift(F1…F0): 100 HzMHz siehe unter FM FSK - Modulation extern Auflösung: Genauigkeit: Datenquelle: 2 10FSK-Ebenen kbit/s Betriebsart: Max.Hub: 16 MHz…3 GHz Bereich(F1…F0): Phasenmodulation 100 HzMHz 16 MHz…3 GHz Auflösung: Bereich(F1…F0): siehe unter FM 10 kbit/s Genauigkeit: Max.Hub: extern 0…10 Datenquelle: Shift(F1…F0): 2 FSK-Ebenen Betriebsart: PSK - Modulation Quelle intern oder siehe unter FMextern 20…10 FSK-Ebenen Genauigkeit: Betriebsart: Shift(F1…F0): 10 kbit/s PSK-Ebenen PSK - Modulation 100 HzMHz Max.Hub: Auflösung: extern Datenquelle: extern Datenquelle: 2 PSK-Ebenen 100 HzMHz Betriebsart: Auflösung: 0…10 PSK<16 - Modulation siehe unterrad FM Shift(F1…F0): Datenrate: Genauigkeit: 10 kbit/s Max.Hub: Hub MHz 0…3,14 10 kbit/s Max.Hub: 2 PSK-Ebenen PSK - Modulation extern siehe unter FM Betriebsart: Datenrate: Genauigkeit: 100 HzMHz Auflösung: Max.Rate: 0…10 Shift(F1…F0): >16 MHz 0…10 rad 2 PSK-Ebenen 0…10 Betriebsart: Shift(F1…F0): extern 10 kbit/s Datenrate: Max.Rate: siehe unter FM Genauigkeit: ShiftPh1…Ph0: 100 HzMHz Auflösung: PSK - Modulation extern 100 Hzunter Datenrate: Auflösung: 10 kbit/s Max.Rate: ShiftPh1…Ph0: <16 MHz: 0…±3,14 rad FM 2 PSK-Ebenen PSK - Modulation Betriebsart: siehe Auflösung 0,01 rad Genauigkeit: 10 kbit/s siehe unter Max.Rate: Genauigkeit: <16 0…±3,14 rad FM 2 PSK-Ebenen ShiftPh1…Ph0: Betriebsart: >16 0…±10 rad extern Datenrate: PSKMHz: - Modulation Genauigkeit ±5 % bis 1 kHz + restliche PM ShiftPh1…Ph0: <16 0…±3,14 rad >16 0…±10 extern Datenrate: 2 PSK-Ebenen 0,01 radrad 10 kbit/s Betriebsart: Auflösung: Max.Rate: PSKMHz: - Modulation Ext.PSK Frequenzgang (bis -1 dB) 10 <16 0…±3,14 rad PM >16 MHz: 0…±10 rad 0,01 rad - Modulation kbit/s Auflösung: Max.Rate: extern siehe unter Datenrate: Genauigkeit: ShiftPh1…Ph0: 2 PSK-Ebenen Betriebsart: >16 0…±10 rad 2extern PSK-Ebenen Betriebsart: 0,01 rad siehe unter PM Auflösung: Genauigkeit: ShiftPh1…Ph0: 10 kbit/s <16 MHz: 0…±3,14 rad Max.Rate: Datenrate: DC-Kopplung 0…100 kHz 0,01 rad extern Auflösung: Datenrate: siehe unter <16 0…±3,14 rad PM Genauigkeit: >16 MHz: 0…±10 rad ShiftPh1…Ph0: 10 kbit/s Max.Rate: Pulsmodulation AC-Kopplung 100 Hz…100 siehe unter 10 kbit/s Genauigkeit: Max.Rate: >16 0…±10 rad <16 MHz: 0…±3,14 rad PM kHz extern (Geräterückseite) Pulsmodulation 0,01 rad Quelle: Auflösung: ShiftPh1…Ph0: ShiftPh1…Ph0: extern (Geräterückseite) 0,01 rad Quelle: Auflösung: >16 MHz: 0…±10 rad Pulsmodulation siehe unter Dynamikumfang: Genauigkeit: <16 0…±3,14 rad Verzerrungen <3 % bei PM fmod = 1 kHz und Hub = 10 rad <16 0…±3,14 rad PM extern (Geräterückseite) siehe unter Quelle: Dynamikumfang: Genauigkeit: 0,01dB rad fPulsmodulation <2 MHz: GHz: >80 Auflösung: >16 0…±10 rad FSK Modulation extern (Geräterückseite) >16 0…±10 rad Quelle: <2 MHz: >80 Dynamikumfang: siehe unter PM fPulsmodulation >2 GHz: >55 dB Genauigkeit: 0,01 rad Auflösung: 0,01 rad Dynamikumfang: Auflösung: <2 GHz: >80 f >2 >55 dB <50 ns (typ. <10 Bereich (F0…F1) 16…3 GHz extern (Geräterückseite) Pulsmodulation Anstiegs-/Abfallzeiten: Quelle: siehe unter PM ns) Genauigkeit: fPulsmodulation <2 >80 siehe PM ns) Genauigkeit: >2 GHz: >55 dB <50 nsunter (typ. <10 extern (Geräterückseite) Anstiegs-/Abfallzeiten: Quelle: <100ns Verzögerung: Dynamikumfang: Betriebsart 2 FSK-Ebenen fPulsmodulation >2 >55 dB (typ. <50 ns ns) <100ns Anstiegs-/Abfallzeiten: Verzögerung: Dynamikumfang: extern (Geräterückseite) 2,5 (typ.<10 5 MHz) <2 GHz: >80MHz Quelle: Max.Frequenz: Datenquelle <50 ns ns) Anstiegs-/Abfallzeiten: <100ns 2,5 MHz (typ.<10 5 MHz) Pulsmodulation f <2 >80 dB (typ. Verzögerung: Max.Frequenz: TTL >2 GHz: >55extern Dynamikumfang: Eingangspegel: extern (Geräterückseite) Quelle: <100ns extern (Geräterückseite) Verzögerung: Quelle: 2,5 MHz (typ.<10 5 MHz) TTL f >2 GHz: >55 dB Max.Frequenz: Eingangspegel: <2 >8010 <50 nskbit/s (typ. ns) Anstiegs-/Abfallzeiten: Dynamikumfang: Max. Rate 2,5 (typ.<10 5 MHz) Max.Frequenz: Dynamikumfang: TTL <50 ns ns) Eingangspegel: Anstiegs-/Abfallzeiten: >2 GHz: >55MHz <100ns Verzögerung: f <2 >80 dB (typ. Wobbelbetrieb Shift (F1…F0) MHz TTL fWobbelbetrieb <2 GHz: >80 dB Eingangspegel: <100ns Verzögerung: <500…10 ns (typ. <10 ns) 1…3000 MHz 2,5 MHz (typ. 5 MHz) Anstiegs-/Abfallzeiten: Bereich: Max.Frequenz: >2 >55 fWobbelbetrieb >2 GHz: >55 dB 1…3000 MHz 2,5 MHz (typ.<10 5 MHz) Bereich: Max.Frequenz: <100ns 500 Hz…2999 MHz TTL Verzögerung: Tiefe: Eingangspegel: <50 ns Hz (typ. ns) Anstiegs-/Abfallzeiten: Auflösung 100 <50 ns (typ. ns) Anstiegs-/Abfallzeiten: 1…3000 MHz Wobbelbetrieb 500 Hz…2999 MHz TTL Bereich: Tiefe: Eingangspegel: 2,5ms…5 MHz (typ. 5 MHz) 20 s <10 Max.Frequenz: Wobbelzeit: <100ns Verzögerung: ±3 %MHz + Genauigkeit 1…3000 <100ns Bereich: Verzögerung: 500 Hz…2999 MHz 20 s restliche Tiefe: Wobbelzeit: TTLms…5 intern Eingangspegel: Trigger: 2,5 MHz (typ. 5 MHz)FM (fmod ≤5 kHz) Max.Frequenz: Wobbelbetrieb ±7 %MHz +s restliche 500 Hz…2999 MHz 2,5 MHz (typ. 5 MHz)FM (5 kHz <fmod <100 kHz) Tiefe: Max.Frequenz: 20 ms…5 intern Wobbelzeit: Trigger: 1…3000 Wobbelbetrieb Bereich: TTL Eingangspegel: 20 ms…5 s MHz TTL Wobbelzeit: Eingangspegel: intern 1…3000 MHz Trigger: Bereich: 500 Hz…2999 Tiefe: Wobbelbetrieb Schutzfunktionen PSK - Modulation intern Trigger: 500 Hz…2999 MHz Tiefe: 1…3000 Der Generator ist gegen Einspeisung inMHz den bis zu 1 W aus 50 Ω Schutzfunktionen 20 ms…5 s HF-Ausgang Bereich: Wobbelzeit: Wobbelbetrieb Betriebsart 2Hz…2999 PSK-Ebenen Der Generator gegen Einspeisung inSchutzschaltung den bis zuden 1 WAusgang aus 50 Ω Wobbelbetrieb 20 s HF-Ausgang Wobbelzeit: 500ms…5 MHz Schutzfunktionen intern sowie gegen DCistbis ±7 V geschützt. Die trennt Tiefe: Trigger: 1…3000 MHz Bereich: 1…3000 MHz Bereich: Der Generator gegen Einspeisung den bis zuden 1 WAusgang aus 50 Ω Schutzfunktionen intern sowie gegen DCistbis ±7Benutzer V geschützt. DieinSchutzschaltung Trigger: 20 ms…5 s HF-Ausgang Wobbelzeit: ab, dieser muss vom wieder aktiviert 500 Hz…2999 MHzwerden.trennt Tiefe: Datenquelle extern Der Generator gegen Einspeisung den bis zuden 1 WAusgang aus 50 Ω 500 Hz…2999 MHzwerden.trennt Tiefe: sowie gegen DCistbis ±7Benutzer V geschützt. DieinSchutzschaltung ab, dieser muss vom wieder aktiviert intern Trigger: 20 ms…5 s HF-Ausgang Wobbelzeit: Schutzfunktionen Max. Ratemuss 10 kbit/s sowie gegen DCistbis ±7Benutzer V geschützt. 20 ms…5 Die s HF-Ausgang Wobbelzeit: ab, dieser vom wieder aktiviert werden.trennt Der Generator gegen Einspeisung inSchutzschaltung den bis zuden 1 WAusgang aus 50 Ω Schutzfunktionen intern Trigger: Verschiedenes intern ab, dieser muss vom wieder aktiviert werden.trennt Trigger: Der Generator gegen Einspeisung den rad HF-Ausgang bis zuden 1 WAusgang aus 50 Ω USB/RS-232 (HO820), Verschiedenes sowie gegen DCistbis ±7Benutzer V MHz geschützt. DieinSchutzschaltung Fernsteuerung: Schutzfunktionen Shift (Ph1…Ph0) <16 0…±3,14 USB/RS-232 (HO820), sowie gegen DCistbis ±7Benutzer V MHz geschützt. DieinSchutzschaltung trennt Fernsteuerung: Der Generator gegen Einspeisung den bis zuden 1 WAusgang aus 50 Ω Verschiedenes IEEE-488 (GPIB) (optional) ab, dieser muss vom wieder aktiviert werden. Schutzfunktionen >16 0…±10 radHF-Ausgang USB/RS-232 (HO820), Verschiedenes Schutzfunktionen IEEE-488 (GPIB) (optional) Fernsteuerung: ab, dieser muss vom wieder aktiviert werden. 10 sowie gegen DCistbis ±7Benutzer V geschützt. DieinSchutzschaltung trennt Konfigurationsspeicher: Der Generator gegen Einspeisung den HF-Ausgang bis zuden 1 WAusgang aus 50 Ω USB/RS-232 (HO820), Der Generator gegen Einspeisung den HF-Ausgang bis zuden 1 W Ausgang aus 50 Ω Fernsteuerung: Auflösung 0,01 10 IEEE-488 (GPIB) (optional) Konfigurationsspeicher: Schutzklasse I (EN61010) ab, dieser muss vom wieder aktiviert werden. Schutzart: sowie gegen DCistbis ±7Benutzer V geschützt. Dieinrad Schutzschaltung trennt Verschiedenes IEEE-488 (optional) sowie gegen DC bis ±7Benutzer V geschützt. Die Schutzschaltung trennt den Ausgang 10 Schutzklasse I %, (EN61010) Konfigurationsspeicher: Schutzart: 115…230 V(GPIB) ±10 50/60 Hz, CAT USB/RS-232 Verschiedenes Netzanschluss: Fernsteuerung: ab, dieser muss vom wieder werden. Genauigkeit ±5 % aktiviert bis 1(HO820), kHz + restliche PMII 10 Konfigurationsspeicher: ab, dieser muss vom Benutzerca. wieder werden. Schutzklasse I %, (EN61010) 115…230 V(GPIB) ±10 50/60 Hz, CAT II USB/RS-232 (HO820), Schutzart: Netzanschluss: Fernsteuerung: 40 VAaktiviert IEEE-488 (optional) Leistungsaufnahme: Verschiedenes Schutzklasse I %, (EN61010) Schutzart: 115…230 V(GPIB) ±10 50/60 Hz, CAT II ca. 40 VA°C Netzanschluss: IEEE-488 (optional) Leistungsaufnahme: USB/RS-232 (HO820), +5…+40 10 Fernsteuerung: Arbeitstemperatur: Konfigurationsspeicher: Verschiedenes 115…230 V(GPIB) ±10 50/60 Hz, CAT II Netzanschluss: ca. 40 VA°C +5…+40 Verschiedenes 10 Leistungsaufnahme: Arbeitstemperatur: Konfigurationsspeicher: -20…+70 °C IEEE-488 (optional) Schutzklasse I %, (EN61010) Lagertemperatur: Schutzart: USB/RS-232 (HO820), Fernsteuerung: ca. USB/RS-232 (HO820), Leistungsaufnahme: Fernsteuerung: +5…+40 -20…+70 °C Schutzklasse IKondensation) (EN61010) Arbeitstemperatur: Lagertemperatur: Schutzart: 10 40%VA°C 115…230 V(GPIB) ±10 %, 50/60 Hz, CAT II Konfigurationsspeicher: Netzanschluss: IEEE-488 (optional) 5…80 (ohne Rel.Luftfeuchtigkeit: +5…+40 Arbeitstemperatur: IEEE-488 (optional) -20…+70 115…230 V(GPIB) ±10Imm %, 50/60 Hz, CAT II Lagertemperatur: Netzanschluss: Schutzklasse (EN61010) ca. 40 VA°C Schutzart: Leistungsaufnahme: 10 Konfigurationsspeicher: 285 x 75 x°C 365 Abmessungen(B x H x T): -20…+70 °C 10 Lagertemperatur: Konfigurationsspeicher: VA°C Leistungsaufnahme: 115…230 V ±10I %, 50/60 Hz, CAT II +5…+40 Netzanschluss: Arbeitstemperatur: Schutzklasse (EN61010) Schutzart: ca. 540kg Gewicht: Technische Daten Pulsmodulation Quelle extern (Geräterückseite) Dynamikumfang f <2 GHz f >2 GHz >80 dB >55 dB Anstiegs-/Abfallzeiten <50 ns (typ. <10 ns) Verzögerung <100 ns Max. Frequenz 2,5 MHz (typ. 5 MHz) Eingangspegel TTL Wobbelbetrieb Bereich 1…3.200 MHz Tiefe 500 Hz…2.999 MHz Wobbelzeit 20 ms…5 s Trigger intern Schutzfunktionen Der Generator ist gegen Einspeisung in den HF-Ausgang bis zu 1 W aus 50 Ω sowie gegen DC bis ±7 V geschützt. Die Schutzschaltung trennt den Ausgang ab, dieser muss vom Benutzer wieder aktiviert werden. Verschiedenes Schnittstelle Dual-Schnittstelle USB/RS-232 (HO820), IEEE-488 (GPIB) (optional) Konfigurationsspeicher 10 Schutzart Schutzklasse I (EN61010-1) Netzanschluss 115/230 V ±10 %, 50…60 Hz, CAT II Leistungsaufnahme ca. 40 VA Arbeitstemperatur +5…+40 °C Lagertemperatur -20…+70 °C Rel. Luftfeuchtigkeit 5…80 % (ohne Kondensation) Abmessungen (B x H x T) 285 x 75 x 365 mm Gewicht ca. 5 kg Im Lieferumfang enthalten Netzkabel, Bedienungsanleitung, CD Empfohlenes Zubehör HO85 HO880 HZ13 HZ14 HZ20 HZ21 HZ24 HZ33 HZ34 HZ42 HZ72 OCXO, Temperaturstabilität ±1 x 10 -8 (Einbau nur ab Werk) IEEE-488 (GPIB) Schnittstelle, galvanisch getrennt Schnittstellenkabel (USB) 1,8 m Schnittstellenkabel (seriell) 1 1 Adapterstecker (BNC-Stecker auf Bananenbuchse) Adapterstecker (N-Stecker auf BNC-Buchse) Dämpfungsglieder 50Ω (3/6/10/20 dB) Messkabel 50 Ω, (BNC/BNC), 0,5 m Messkabel 50 Ω, (BNC/BNC), 1,0 m 19” Einbausatz 2HE IEEE-488 (GPIB) Schnittstellenkabel 2 m HAMEG Instruments GmbH | Industriestr. 6 | 63533 Mainhausen | Tel +49 (0) 6182 8000 | R&S® ist ein eingetragenes Warenzeichen der Rohde & Schwarz GmbH & Co. KG 25 HAMEG Instruments® ist ein eingetragenes Warenzeichen der HAMEG Instruments GmbH | Markennamen sind Warenzeichen der Eigentümer Version 02.01 | 08 / 2014 | © HAMEG Instruments GmbH | Daten ohne Genauigkeitsangabe sind unverbindlich | Änderungen vorbehalten General information concerning the CE marking KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY DECLARATION DE CONFORMITE Hersteller / Manufacturer / Fabricant / Fabricante: HAMEG Instruments GmbH · Industriestraße 6 · D-63533 Mainhausen Die HAMEG Instruments GmbH bescheinigt die Konformität für das Produkt The HAMEG Instruments GmbH herewith declares conformity of the product HAMEG Instruments GmbH déclare la conformite du produit Bezeichnung: HF-Synthesizer Product name: RF-Synthesizer Designation:HF-Synthesizer Typ / Type / Type: HM8135, HM8135X mit / with / avec: HO820 Optionen / Options / Options: HO880 mit den folgenden Bestimmungen / with applicable regulations / avec les directives suivantes: EMV Richtlinie: 2004/108/EG EMC Directive: 2004/108/EG Directive CEM: 2004/108/EG Niederspannungsrichtlinie: 2006/95/EG Low-Voltage Equipment Directive: 2006/95/EG Directive des equipements basse tension: 2006/95/EG Angewendete harmonisierte Normen / Harmonized standards applied / Normes harmonisées utilisées: Sicherheit / Safety / Sécurité: EN 61010-1 (07/2011) Elektromagnetische Verträglichkeit / Electromagnetic compatibility / Compatibilité électromagnétique: EMV Störaussendung / EMI Radiation / Emission CEM: EN 61326-1 (10/20116) IEC/CISPR 11 ( 2009, modifiziert + A1:2010), DIN VDE 0876 (10/2007), DIN VDE 0877 (08/2007) Störfestigkeit / Immunity / Imunitee: EN 61326-1 (10/20116)1 EN 61000-4-2 (12/2009), EN 61000-4-3 (04/2011), EN 61000-4-4 (11/2010), EN 61000-4-5 (06/2007), EN 61000-4-6 (12/2009), EN 61000-4-8 (11/2010), EN 61000-4-11 (02/2005) Datum / Date / Date 21. 06. 2012 26 Unterschrift / Signature / Signatur / Signatura Holger Asmussen General Manager General remarks regarding the CE marking Hameg measuring instruments comply with the EMI norms. Our tests for conformity are based upon the relevant norms. Whenever different maximum limits are optional Hameg will select the most stringent ones. As regards emissions class 1B limits for small business will be applied. As regards susceptibility the limits for industrial environments will be applied. All connecting cables will influence emissions as well as susceptability considerably. The cables used will differ substantially depending on the application. During practical operation the following guidelines should be absolutely observed in order to minimize emi: 1. Data connections Measuring instruments may only be connected to external associated equipment (printers, computers etc.) by using well shielded cables. Unless shorter lengths are prescribed a maximum length of 3 m must not be exceeded for all data interconnections (input, output, signals, control). In case an instrument interface would allow connecting several cables only one may be connected. In general, data connections should be made using double-shielded cables. For IEEE-bus purposes the double screened cable HZ72 from HAMEG is suitable. 2. Signal connections In general, all connections between a measuring instrument and the device under test should be made as short as possible. Unless a shorter length is prescribed a maximum length of 3 m must not be exceeded, also, such connections must not leave the premises. All signal connections must be shielded (e.g. coax such as RG58/U). With signal generators double-shielded cables are mandatory. It is especially important to establish good ground connections. 3. External influences In the vicinity of strong magnetic or/and electric fields even a careful measuring set-up may not be sufficient to guard against the intrusion of undesired signals. This will not cause destruction or malfunction of Hameg instruments, however, small deviations from the guaranteed specifications may occur under such conditions. General information concerning the CE marking HAMEG Instruments GmbH Content Content General information concerning the CE marking. . . 26 1 Important hints. . . . . . . . . . . . . . . . . . . . . . . . . 28 1.1Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 1.2Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 1.3Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 1.4 Transport and Storage . . . . . . . . . . . . . . . . . . . . . . . 28 1.5 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 28 1.6 Proper operating conditions. . . . . . . . . . . . . . . . . . . 28 1.7 Warranty and Repair. . . . . . . . . . . . . . . . . . . . . . . . . 29 1.8Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 1.9 Line voltage selector. . . . . . . . . . . . . . . . . . . . . . . . . 29 1.10 Change of fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2 Controls and display. . . . . . . . . . . . . . . . . . . . . 30 3 Indroduction of the HM8135. . . . . . . . . . . . . . 31 3.1 First time operation. . . . . . . . . . . . . . . . . . . . . . . . . . 31 3.2Switch-on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 3.3 Factory configuration . . . . . . . . . . . . . . . . . . . . . . . .31 3.4Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 3.5 ESC key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 3.6 Setting parameters. . . . . . . . . . . . . . . . . . . . . . . . . . 31 3.7 Selecting frequency. . . . . . . . . . . . . . . . . . . . . . . . . 32 3.8 Selecting level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 3.9 Selecting modulations . . . . . . . . . . . . . . . . . . . . . . . 32 4 Types of Modulation. . . . . . . . . . . . . . . . . . . . . 34 4.1 Amplitude modulation (AM) . . . . . . . . . . . . . . . . . . 34 4.2 Frequence modulation (FM). . . . . . . . . . . . . . . . . . . 34 4.3 Phase modulation (PM) . . . . . . . . . . . . . . . . . . . . . . 35 4.4 FSK modulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.5 PSK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.6 GATE modulation. . . . . . . . . . . . . . . . . . . . . . . . . . . 36 5 Setting the configuration. . . . . . . . . . . . . . . . . 37 5.1 Selecting step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 5.2 MENU key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 5.3 Level Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 5.4 Reference REF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 5.5 Special function Sfc. . . . . . . . . . . . . . . . . . . . . . . . . 38 5.6 Beeper Beep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 5.7 Encoder Enco. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 5.8 Interface Com. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 5.9 Display LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 5.10SWEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 5.11Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 5.12Trig: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 5.13 PREV. key (Previous). . . . . . . . . . . . . . . . . . . . . . . . . 40 5.14 ON key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 5.15 RCL / STO keys (Recall & Store). . . . . . . . . . . . . . . . 40 6 Remote Operation . . . . . . . . . . . . . . . . . . . . . . 41 6.1Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.2 Retrofit or change the interface. . . . . . . . . . . . . . . . 41 6.3 Commands supported. . . . . . . . . . . . . . . . . . . . . . . 41 6.4 Commands description . . . . . . . . . . . . . . . . . . . . . . 42 6.5 General commands . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.6 Bus commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.7 Sound commands . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.8OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.9 POWER commands. . . . . . . . . . . . . . . . . . . . . . . . . 42 6.10 FREQUENCY commands. . . . . . . . . . . . . . . . . . . . . 42 6.11PHASE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 6.12 PULM (PULse Modulation). . . . . . . . . . . . . . . . . . . . 43 6.13 AM (Amplitude Modulation). . . . . . . . . . . . . . . . . . . 43 6.14 FM (Frequency Modulation). . . . . . . . . . . . . . . . . . . 44 6.15 PM (Phase Modulation) . . . . . . . . . . . . . . . . . . . . . . 44 6.16FSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.17PSK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.18SWEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.19SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.20 Error codes and their meaning. . . . . . . . . . . . . . . . . 46 7 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . 48 Flow Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 27 Important hints 1 Important hints (1) (2) (3) (4) 1.1Symbols Symbol 1: Attention, please consult manual Symbol 2: Danger! High voltage! Symbol 3: Ground connection Symbol 4: Stop! Possible instrument damage! 1.2Unpacking Please check for completeness of parts while unpacking. Also check for any mechanical damage or loose parts. In case of transport damage inform the supplier immediately and do not operate the instrument. Check setting of line voltage selector whether it corresponds to the actual line voltage. 1.3Positioning Two positions are possible: According to Fig. 1 the front feet are folded down and are used to lift the instrument so its front points slightly upward (approx. 10 degrees). If the feet are not used (Fig. 2) the instrument can be stacked safely with many other Hameg instruments. In case several instruments are stacked (Fig. 3) the feet rest in the recesses of the instrument below so the instruments can not be inadvertently moved. Fig. 1 Fig. 2 Fig. 3 Please do not stack more than 3 instruments. A higher stack will become unstable, also heat dissipation may be impaired 28 1.4 Transport and Storage Please keep the shipping carton in case the instrument may require later shipment for repair. Losses and damages during transport as a result of improper packaging are excluded from warranty! Dry indoors storage is required. After exposure to extreme temperatures 2h for accomodation to ambient temperature before turning the instrument on. 1.5 Safety instructions The instrument conforms to VDE 0411/1 safety standards applicable to measuring instruments and left the factory in proper condition according to this standard. Hence it conforms also to the European standard EN 61010-1 resp. to the international standard IEC 61010-1. Please observe all warnings in this manual in order to preserve safety and guarantee operation without any danger to the operator. According to safety class 1 requirements all parts of the housing and the chassis are connected to the safety ground terminal of the power connector. For safety reasons the instrument must only be operated from 3 terminal power connectors or via isolation transformers. Do not disconnect the safety ground either inside or outside of the instrument! In case of doubt the power connector should be checked according to DIN VDE 0100/610: ❙❙ The line voltage of the instrument as shown on the type label must correspond to the line voltage used. ❙❙ Only qualified personnel may open the instrument ❙❙ Prior to opening the instrument must be disconnected from the line and all other inputs/outputs. In any of the following cases the instrument must be taken out of service and locked away from unauthorized use: ❙❙ Visible damages ❙❙ Damage to the power cord ❙❙ Damage to the fuse holder ❙❙ Loose parts ❙❙ No operation ❙❙ After longterm storage in an inappropriate environment, e.g. open air or high humidity. ❙❙ Excessive transport stress 1.6 Proper operating conditions The instruments are destined for use in dry clean rooms. Operation in an environment with high dust content, high humidity, danger of explosion or chemical vapors is prohibited. The maximum permissible ambient temperature during operation is +5 °C to +40 °C. In storage or during transport the temperature limits are: –20 °C to +70 °C. In case of exposure to low temperature or if condensation is suspected, the instrument must be left to stabilize for at least 2 hrs prior to operation. For safety reasons operation is only allowed from 3 terminal connectors with a safety ground connection or via isolation transformers of class Important hints 2. The instrument may be used in any position, however, sufficient ventilation must be assured as convection cooling is used. For continuous operation prefer a horizontal or slightly upward position using the feet. Do not cover either the holes of the case nor the cooling fins. Specifications with tolerances are valid after a 30 minute warmup period and at 23 °C. Specifications without tolerances are typical values of an average instrument. 1.7 Warranty and Repair HAMEG instruments are subjected to a strict quality control. Prior to leaving the factory, each instrument is burntin for 10 hours. By intermittent operation during this period almost all defects are detected. Following the burnin, each instrument is tested for function and quality, the specifications are checked in all operating modes; the test gear is calibrated to national standards. The warranty standards applicable are those of the country in which the instrument was sold. Reclamations should be directed to the dealer where the instrument was purchased. Only valid in EU countries In order to speed reclamations customers in EU countries may also contact HAMEG directly. Also, after the warranty expired, the HAMEG service will be at your disposal for any repairs (see RMA). 1.9 Line voltage selector The instrument is destined for operation on 115 or 230 V mains, 50/60 Hz. The proper line voltage is selected with the line voltage selector. It is necessary to change the fuse observing the proper values printed on the back panel. Please note: After changing the main volage, the line fuse has to be changed. Otherwise the instrument may be destroyed. 1.10 Change of fuse The mains fuse is accessible on the back panel. A change of the fuse is only allowed after the instrument was disconnected from the line and the power cord removed. Fuse holder and power cord must not show any sign of damage. Use a screw driver to loosen the fuse holder screw counterclockwise while pressing the top of the fuse holder down. The top holding the fuse will then come off. Exchange the defective fuse against a correct new one. It is forbidden to repair defective fuses or to bridge them by any means. Any damage caused this way will void the warranty. Type of fuse: 5 x 20 mm; 250V~, C; IEC 127/III; DIN 41662 (DIN 41571/3). Value 115 V: 1.0 A slow blow 230 V: 0.5 A slow blow Return material authorization (RMA): Prior to returning an instrument to HAMEG ask for a RMA number either by internet (http://www.hameg.com) or fax (+49 (0) 6182 800 500). If you do not have an original shipping carton, you may obtain one by calling the HAMEG service dept (+49 (0) 6182 800 500) or by sending an email to [email protected]. 1.8Maintenance Clean the outer case using a dust brush or a soft, lintfree dust cloth at regular intervals. The display can be cleaned using water or a glass cleaner (but not with alcohol or other cleaning agents). Thereafter wipe the surfaces with a dry cloth. No fluid may enter the instrument. Do not use other cleaning agents as they may adversely affect the labels, plastic or lacquered surfaces. Before cleaning please make sure the instrument is switched off and disconnected from all power supplies. No part of the instrument should be cleaned by the use of cleaning agents (as f.e. alcohol) as they may adversely affect the labeling, the plastic or lacquered surfaces. 29 Controls and display 2 Controls and display 9 FUNCTIONS: Functions keys and LEDs 10 Rotary knob: Dial for setting all parameters 11 NUMERIC KEYPAD: Input parameters with unit validation 12 ON: Key for activation the output 13 ESC (Escape): Cancels the current display Front panel 14 RF OUTPUT 50 Ω (Radio Frequency Output): 1 POWER (button): Power switch and led Signal output 2 MOD. INPUT (Modulation input): 15 MOD. OUTPUT (Modulation Output): Input of external modulation Output for modulation signal 3 PREV. (Previous): Selection of previous menu Rear panel 4 MEMORY RCL (Memory Recall): 16 Power receptacle Key for recalling one of 10 memories for instrument settings 5 CONTEXT SENSITIVE KEYS: 17 VOLTAGE SELECTOR: Selection of the line voltage 18 F1 (FUSE): Mains fuse Function depending on the context display 19 GATE INPUT: TTL-compatible 6 MEMORY STO (Memory Store): Key for storing one of 10 memories for instrument settings 20 REF. 10 MHz OUTPUT: Output for reference signal 21 REF. 10 MHz INPUT: Input for reference signal 7 MENU: Input key in the configuration menu 22 RS-232: Serial port 8 DISPLAY: 23 Dual Interface: USB/RS-232 (HO820) Two lines of 20 characters each on a backlight LCD optional: IEEE-488 GPIB (HO880) 8 2 3 4 5 6 10 7 9 11 13 1 12 14 Fig. 2.1: Front panel of the HM8135 23 16 Fig. 2.2: Rear panel of the HM8135 30 18 17 22 21 20 19 15 Indroduction of the HM8135 3 Indroduction of the HM8135 3.1 First time operation Before starting the instrument the first time, please check the following: ❙❙ The line voltage indicated on the rear panel corresponds to the available line voltage, also, the correct fuses for this line voltage are installed. The fuses are contained in the line voltage connector housing. ❙❙ The connection to the mains is either by plugging into a socket with safety ground terminal or via an isolation transformer of protection class II. ❙❙ No visible damage to the instrument. ❙❙ No visible damage to the line cord. ❙❙ No loose parts floating around in the instrument. 3.2Switch-on After depressing the red power key 1 , the display of the HM8135 will successively show the following messages: ❙❙ the type (SYNTHESIZER) and the version of the instrument (HM8135) ❙❙ the self-test messages ”RAM checking“ and ”DDS loading“ (RAM = Random Acess Memory; DDS = Direct Digital Synthesis) ❙❙ Optional interface: Second Com Interface: NONE, RS-232 (HO890), IEEE488 (HO880), USB (HO870) ❙❙ Optional OCXO: FREQUENCY REFERENCE OCXO OPTION > NO (YES) ❙❙ the reference soure in progress (internal or external): FREQUENCY REFERENCE Internal (External) After switch-on the HM8135 has the configuration stored in the configuration memory 0. The output signal is disabled after switch-on by default. 3.3 Factory configuration At delivery the instrument is adjusted for a basic set-up: ❙❙ Frequency: 3000 MHz ❙❙ Level: +7 dBm ❙❙ No modulation ❙❙ Reference source: internal ❙❙ Fmod: 1 kHz, Shape: sine (for all modulations) ❙❙ Dev: 20 kHz (FM), Dev: 1 rad (PM) , Depth: 50% (AM) ❙❙ Contrast: maximum ❙❙ Sound indicator: none ❙❙ Interface parameters: 4800 baud / 1 stopbit / 8 data bits This basic adjustment can be recalled at any time as follows: ❙❙ Switch off the unit. ❙❙ Switch on the unit and hold the ESC key until you hear several beeps. This procedure is especially suited in case of doubt. Caution: The 10 memories storing configurations are erased and replaced by the previous basic adjustments. 3.4 Main Display This display shows the frequency and the level of the RF output signal and the reference in use (INTernal or EXTernal). If no modulation (AM, FM, PM) is turned on, the display shows: Moreover, it contains some modulation parameters (for example in case of AM modulation, shape SQR and Fmod = 1 kHz). This state is left by pressing one of the function keys 9 or the MENU key 7 . 3.5 ESC key The ESC key 13 allows the user to return to the main display, to unselect the current function 9 or to cancel the numeric keypad input. 3.6 Setting parameters Once a parameter is selected (for example FREQ.) with a function key 9 , a new value for this parameter can be entered from the data keypad 11 or modified by the digital rotary 10 or by one of the four context sensitive keys 5 below the displayed marks – and + . The operation of the data keypad is conventional. Depress successively the numeric keys representing the parameter value and at the end the unit key (for example MHz or dBm). Note that it is not necessary to enter any leading zeros. The instrument always displays at least one digit on the left of the comma. Before the unit selection, it is possible to cancel the value by pressing the ESC key 13 . In this case the previous value is restored. The encoder 10 modifies the value of the digit underlined by the cursor (if the cursor underlines a blank position, it is considered as 0). The cursor is shifted to another position by pressing the keys below the 2 arrows 5 and the value can be increased or decreased by operating – or +. An unproper value is announced by a warning message and the sound indicator if activated (except for out of range of en31 Indroduction of the HM8135 coder and steps). 3.7 Selecting frequency After pressing the FREQ. key 9 , the display shows: ❙❙ FSK (Frequency shift keying) ❙❙ PSK (Phase shift keying) ❙❙ GATE (Gate modulation) The return to the previous display is possible by pressing the PREV. key 3 . A new value can be entered from the data keypad 11 or modified by the digital rotary knob 10 or by one of the four context sensitive keys 5 . For more details, refer to the paragraph ”Setting parameters“. The frequency range is 1 Hz to 1200 MHz. The resolution is 1 Hz. If a value is entered with a higher resolution, the instrument makes a truncation keeping 1 Hz resolution. 3.8 Selecting level After pressing the LEVEL key 9 , the display shows: A new value of the level can be entered from the data keypad 11 or modified by the digital rotary knob 10 or by one of the four context sensitive keys 5 . For more details, refer to the paragraph ”Setting parameters“. After selecting the type of modulation (FM MENU), the display shows: The selection of the parameters for AM/FM/PM is made by pressing one of the four context sensitive keys 5 corresponding to: ❙❙ The shape of internal modulation signal ❙❙ The frequency of the internal modulation signal ❙❙ The deviation (or depth in AM) ❙❙ The modulation state The return to the previous display is possible by pressing the PREV. key 3 . After selecting the Shape option (AM SHAPE MENU), the display shows: The level range is: ❙❙ -135 dBm to +13 dBm without amplitude modulation ❙❙ -135 dBm to +7 dBm with amplitude modulation ❙❙ The resolution is 0.1 dBm. The level displayed is specified for a load of 50 Ω. The choice of the unit is made by the keypad 11 dBm, mV or µV . For the volt unit the instrument performs a three digits resolution according to the range (mV/µV/nV). Caution: If the AM modulation is activated, the instrument automatically limits the level to +7 dBm in order to avoid an excess of the dynamic of the ouput amplifier. 3.9 Selecting modulations After pressing the MOD. key 9 , the display shows: The shape of the internal modulation signal may be modified by the context sensitive keys 5 . The active signal is pointed out by a triangle . The return to the previous menu is possible by pressing the PREV. key 3 . After selecting the Fmod option (AM MENU), the display shows: MODULATION MENU AM FM PM – –> MODULATION MENU <– – FSK PSK GATE The modulation type is selected by pressing one of the four context sensitive keys 5 corresponding to: ❙❙ AM (Amplitude modulation) ❙❙ FM (Frequency modulation) ❙❙ PM (Phase modulation) 32 The frequency of the internal modulation signal may be directly changed by the numeric keypad 11 or modified by the digital rotary knob 10 or by one of the four context sensitive keys 5 . The return to the previous menu is possible by pressing the PREV. key 3 . The frequency range is: ❙❙ 10 Hz to 200 kHz: Sine (Step 10 Hz) ❙❙ 10 Hz to 20 kHz: Triangle, Square, Sawthooth (Step 10 Hz) Indroduction of the HM8135 The modulation is turned on by pressing the context sensitive key 5 below the string off. One time for turning the internal source on (INT) and a second time for turning the external source on (EXT). The active source is pointed out by a triangle beside the option.The indicator LED of the MOD.OUTPUT is lighting. Pressing the context sensitive key 5 once again, the modulation will be deactivated (OFF). The return to the previous menu is possible by pressing the PREV. key 3 . CH2 moduled signal (deviation: 2 kHz) Example 2: In this example, the external modulation signal is a ”trinary“ code composed of 9 bits. One bit is composed of 2 narrow and / or wide pulses, depending on the combination expected: ❙❙ A bit composed of 1 wide and 1 narrow pulses is called OPEN. ❙❙ A bit composed of 2 narrow pulses is called LOW. ❙❙ A bit composed of 2 wide pulses is called HIGH. For detecting the first bit, a synchronisation bit (long low level) is present. The modulation frequency is 20 Hz. With external AM activated, the only modifiable option is the modulation depth (see paragraph ”Amplitude modulation“). The external modulation frequency for AM must be in the range: 10 Hz to 100 kHz With external FM or PM activated, several cases are possible: ❙❙ DC coupled (DC – 100 kHz) ❙❙ AC coupled (100 Hz – 100 kHz) ❙❙ Deviation (see corresponding paragraph) CH1: modulation: narrow pulse of 200 µs wide pulse of 1.8 ms synchronisation bit of 14 ms CH2: zoom of CH1 Example 1: CH1: demodulated signal: DC coupled CH2: demodulated signal: AC coupled The return to the modulation menu is possible by pressing the PREV. key 3 and the return to the main display by pressing the ESC key 13 . The external modulation input is on the front panel (MOD. INPUT). The signal can be of any shape, however the AMdepth and FM/PM deviation programmed is calibrated only for a 2 VRMS signal at the input. CH1: modulation: first pulse width 150 s second pulse width 1.1 ms period 2.5 ms (Fmod: 400 Hz) 33 Types of Modulation 4 Types of Modulation Example 5: For AM triangle (depth: 50%), the display shows: 4.1 Amplitude modulation (AM) After selecting D% (AM MEMU) using the context sensitive keys 5 , the display shows: A new value of the modulation depth can be entered from the data keypad 11 or modified by the rotary knob 10 or by one of the four context sensitive keys 5 . Example 6: For AM positive ramp (depth: 50%), the display shows: The modulation depth may be changed from 0 to 100% with a resolution of 0.1%. The return to the previous menu is possible by pressing the PREV. key 3 and the return to the main display by pressing the ESC key 13 . Example 3: For AM sine (depth: 50%), the display shows: Example 7: For AM negative ramp (depth: 50%), the display shows: Example 4: For AM square (depth: 50%), the display shows: 4.2 Frequence modulation (FM) After selecting DEV (FM MEMU) using the context sensitive keys 5 , the display shows: A new value of the deviation can be entered from the data keypad 11 or modified by the rotary knob 10 or by one of 34 Types of Modulation the four context sensitive keys 5 . For more details, refer to paragraph 3.6 Setting parameters. The deviation (step 100 Hz) may be changed from: ❙❙ ±200 Hz to ±150 kHz (<16 MHz) ❙❙ ± 2 kHz to ±400 kHz (16 - 250 MHz) ❙❙ ± 1 kHz to ±100 kHz (250 - 500 MHz) ❙❙ ± 1 kHz to ±200 kHz (500 -1000 MHz) ❙❙ ± 2 kHz to ±400 kHz (1000 -3000 MHz) A new value of this deviation can be entered from the data keypad 11 or modified by the rotary knob 10 or by one of the four context sensitive keys 5 . For more details, refer to paragraph 3.6 Setting parameters. The deviation range may be set from: ❙❙ 0 to 3.14 rad (<16 MHz) ❙❙ 0 to 10 rad (16 – 3000 MHz) ❙❙ Setting with a step of 0.01 rad. The return to the previous menu is possible by pressing the PREV. key 3 and the return to the main display by pressing the ESC key 13 . The return to the previous menu is possible by pressing the PREV. key 3 and the return to the main display by pressing the ESC key 13 . Example 8: For FM sine, the display shows: Example 10: For PM sine (deviation: 1 rad), the display shows: (deviation: 400 kHz) Example 9: For FM square, the display shows: CH1: modulation signal CH2: modulated signal (deviation: 80 kHz) Example 11: For PM square, the display shows: CH1: modulation signal CH2: modulated signal (deviation: 1 rad) 4.3 Phase modulation (PM) After selecting DEV (PM MEMU) using the context sensitive keys 5 , the display shows: 35 Types of Modulation 4.4 FSK modulation After selecting F0 or F1 (FSK MENU) with the context sensitive key 5 , the display shows: Fsk0: 512.000000 MHz – stp + cur Example 13: For modulation PSK, the display shows: 1200.000000 MHz +13.0dBm PSK Ext Fsk1: 522.000000 MHz – stp + cur A new value of Fsk0 or Fsk1 can be entered from the data keypad 11 or modified by the rotary knob 10 or by one of the four context sensitive keys 5 . For more details, refer to paragraph 3.6 Setting parameters. The skip frequency Fsk0 Fsk1 or Fsk1 Fsk0 may be set from: ❙❙ 0 to 10 MHz (16 MHz - 3000 MHz) ❙❙ step 1 Hz Psk0: –3,14 rad; Psk1: 3,14 rad; Fmod: 1 kHz; Level TTL The return to the previous menu is possible by pressing the PREV. key 3 and the return to the main display by pressing the ESC key 13 . Example 12: For modulation FSK, the display shows: 1190.000000 MHz 1200.000000 MHz FSK Ext Fsk0: 1190.000000 MHz Fsk1: 1200.000000 MHz 4.5 PSK Modulation After selecting PH0 or PH1 (PSK menu) with the context sensitive key 5 , the display shows: Psk0: – stp + –10.00rad cur Psk1: – stp + 10.00rad cur A new value of Psk0 or Psk1 can be entered from thedata keypad 11 or modified by the rotary knob 10 or by one of the four context sensitive keys 5 . For more details, refer to paragraph 3.6 Setting parameters. The skip phase Psk0 Psk1 or Psk1 Psk0 may be set from: ❙❙ -3.14 rad to 3.14rad (<16 MHz) ❙❙ -10 rad to 10 rad (16 – 3000 MHz) ❙❙ step 0.01 rad The return to the previous menu is possible by pressing the PREV. key 3 and the return to the main display by pressing the ESC key 13 . 36 Psk0: 0 rad; Psk1: 3,14 rad; Fmod: 1 kHz; Level TTL 4.6 GATE modulation The GATE modulation is made by sampling the output carrier with a logic signal (GATE) and is characterised by: ❙❙ Duty cycle ❙❙ Rise / Fall time ❙❙ Delay time The GATE signal (TTL level) is applied to the GATE INPUT 19 at the rear panel. When the GATE signal is at the state active (optional level 1 or 0), the carrier is present at the output. After selecting GATE (modulation menu) with the four context sensitive keys 5 , the display shows: Press one of the four context sensitive keys 5 for selecting the active level and for turning the gate on or off. Two tri, , and on or off. angles point out the options Setting the configuration The return to the previous menu is possible by pressing the PREV. key 3 and the return to the main display by pressing the ESC key 13 . 5 Setting the configuration The GATE modulation can be active with another modulation (for example the GATE modulation with AMsin modulation and Fmod = 10 kHz) 5.1 Selecting step After pressing the STEP function key 9 , the display shows: Example 14: (Fgate: 250 Hz Sqr) GATE Phi Now the step type is selected by pressing one of the four context sensitive keys 5 . If the parameter is already selected, the step type can directly be modified by pressing the STEP function key 9 . Press again the step key to go back to previous display. CH1: CH2: AM signal (depth: 50%) and GATE modulation signal with GATE modulation A new value of the step can be entered from the data keypad 11 or modified by the digital rotary control 10 or by one of the four context sensitive keys 5 . For more details, refer to the paragraph 3.6 Setting parameters. The step can modified for: ❙❙ FSTEP: (frequency) ❙❙ Level STEP: (level) ❙❙ Fmod STEP: (modulation frequency) ❙❙ AM STEP: (AM-depth) ❙❙ FM STEP: (FM-deviation) ❙❙ Phi STEP: (PM-deviation) 5.2 MENU key Offs MAIN MENU Ref Sfc SWEEP Operating the MENU key 7 accesses the configuration menu. The options are selected by pressing one of the context sensitive keys 5 . The return to the main display is possible by pressing the ESC key 13 . 5.3 Level Offset (from firmware version 1.23) Pressing the key under Offs gives access to the level offset menu below: 37 Setting the configuration * LEV. OFFSET Att. On MENU * Off 5.4 Reference REF On Activation of the attenuator compensation. Output level is updated according to the attenuation value. Off Deactivation of the attenuator compensation. Output level is updated. Att. Gives access to the menu permitting the edition of the external attenuator value. When activated the actual level takes into account the attenuation value of the external attenuator. The output level at the output of the generator is: Pset+Att, with Pset = programmed output level in dBm, Att = attenuation value in dB. If the actual programmed level is above Pmax+Att the output level is automatically reduced in order that the output level of the generator never exceeds its maximum level (+13 dBm with deactivated amplitude modulation (AM) or +7dBm with activated amplitude modulation). When turning OFF the attenuator correction, if the actual level is below –135 dBm the level is automatically set to –135 dBm. Att.: – stp + 20.0dB cur The settings of the Level Offset will be save into non-volatile memory automatically. To escape from this menu without saving by pressing PREV. key. The attenuation of the external attenuator can be entered directly using the keypad. Press dBm unit key after entering the value. The value can be increased or decreased with 1 dB step using – and + step key. The value can also be modified using the encoder and cursor keys. The output is updated accordingly when the attenuator value is changed. The allowed attenuation range is 0.0 dB to 30.0 dB. Press PREV. key to return to the main Level Offset menu. The HM8135 is basically equipped with a temperature controlled crystal oscillator (TCXO) with a reference frequency of 10 MHz. After each access to the configruation menu by using the context sensitive keys 5 , the phaselock loop starts a test of the reference oscillator (locked or unlocked). The external reference frequency must be applied to the REF. INPUT 10 MHz and the internal reference frequency is available on the REF. OUPUT 10 MHz at the rear panel. Caution: If the reference frequency from an external source is not within specifications, the error message error will be displayed. In this case the internal reference will be automatically activated. 5.5 Special function Sfc After selecting the Sfc option in the configuration menu, the display shows: Disp The special function can be selected by pressing the context sensitive keys 5 . 5.6Beeper Beep The built-in beeper will react to every key stroke and will indicate any operation errors. The activation and the adjust-ment of the volume is done in the beeper menu: ❙❙ Soft (soft sound) ❙❙ Loud (loud sound) ❙❙ None (no sound) Using the Level Offset When setting the output level the displayed level takes into account the external attenuator. The allowable level range is decreased by the amount of the attenuation value. The characteristic of the beeper can be selected by prespoints out sing the context sensitive keys 5 . A triangle the current state. Example: With 20.0 dB attenuator and deactivated ampli- 5.7Encoder Enco tude modulation (AM OFF) the level can be adjusted from –147 dBm to –7 dBm. When the attenuator compensation is active the dot symbol is replaced by a colon character in the amplitude display: Level: -140:0 dBm cur – stp + 38 In this menu the activation of the rotary control is done by selecting the On or OFF option with the context sensitive points out the current state. keys 5 . A triangle Setting the configuration 5.8 Interface Com The HM8135 is basically equipped with the serial interface. The instrument is prepared for the installation of either an optional RS-232 (HO890), IEEE-488 (HO880) or an USB (HO870) interface (all galvanically isolated). Only the baud rate of the serial interface can be modified. The optional interface is chosen by operating the context sensitive keys. After power-on the serial interface is activated by default. If you want the optional interface to be activated after power-on, store the instruments settings (optional interface activated) in the configuration memory 0. The parameters are selected by pressing one of the four context sensitive keys 5 : ❙❙ Param (parameter setting) ❙❙ Mode (Continue- / Burst-Mode) ❙❙ Trig (ON / OFF) ❙❙ ON / OFF (Sweep – Status) In this menu item the trigger can switchs on or off. The return to the previous menu is possible by pressing the PREV. key 3 . After the selection of one of the options PARAM or MODE with the context sensetive keys 5 the display shows: Serial interface * It is possible to select the transmission rates 300, 600, 1200, 2400, 4800, 9600 or 19200 baud by pressing the context sensitive key 5 . The other parameters are fixed: ❙❙ no parity ❙❙ 8 data bits ❙❙ 1 stop bit For the connection between PC and instrument you can use a standard 1:1 cable. USB interface You do not have to change the configuration. If required, the baud rate can be changed. Connect the HM8135 with your PC using a USB cable and install the USB drivers like described in the manual of the USB interface HO820. GPIB interface Connect the HM8135 with your PC using a GPIB cable. It is necessary to set the GPIB adress of the HM8135 to the desired value. The adress is changed at the interface on the rear panel. Do this settings only before starting the instrument. It is not possible when the instrument is running. * SWEEP SPAN MENU * LowFreq HighFreq FrLo: 16.000000 MHz cur – stp + FrHi: 1.200000000 GHz cur – stp + EA new value of FrLo or FrHi can be entered from the data keypad 11 , modified by the rotary knob 10 or by one of the four context sensitive keys 5 . The frequency hub between FrLo FrHi may be set from: ❙❙ 1 MHz...1.2 GHz ❙❙ step size 1 Hz * SWEEP STEP MENU * StepCount steptime Step Count: – val + 5.9 Display LCD ** DISPLAY ADJUST ** -Contrast+ -Light+ The contrast and the illumination of the display is adjusted by pressing one of the four context sensitive keys 5 , corres-ponding to + or –. 5.10SWEEP After selecting the Sweep option in the configuration menu, the display shows: *** SWEEP MENU Param Mode Trig SWEEP PARAM MENU * Up Span Steps Step Time: – val + 100 cur 0.10 sec cur The parameters can be in the range of: ❙❙ max. 500 steps ❙❙ step size 10 ms (max. 2,5 s) The return to the previous menu is possible by pressing the PREV. key 3 . *** Off 39 Setting the configuration 5.11Mode: * The current configuration can be stored by pressing a numeric key from 0 to 9. SWEEP MODE MENU * Continue Burst ––> Sweep Count: – val + 10 cur The selection in the menu item MODE can set with the context sensitive keys 5 . 5.12Trig: SWEEP TRIGGER on SIGNAL off In this menu item the edge of the trigger signal (rising/falling) can be adjusted resp. can be switched on/off. The selection can set with the context sensitive keys 5 . The return to the previous menu is possible by pressing the PREV. key 3 . The return to the main menu is possible by pressing the ESC key 13 . After completing the parameter input the display shows: 1.16.000000MHz 1.200000000GHz SWE 10.0s SWE shows the calculated sweep time and is the result of: Step Count * Step Time e.g.: 100 * 0,1s = 10s 5.13 PREV. key (Previous) The return to the previous menu is possible by pressing the PREV. key 3 . 5.14 ON key The output RF OUTPUT 14 is only active if the ON key 12 is pressed and the corresponding LED is lighted. When the signal is not active, the output is an open circuit. 5.15 RCL / STO keys (Recall & Store) The instrument is equipped with an internal non-volatile memory which stores all parameters in use (frequency, level, modulation ...) when the power is switched off. In addition to this the instrument offers the possibility to store 10 complete configurations. After pressing the STO key 6 , the display shows: 40 After pressing the RCL key 4 , the display shows: A configuration can be recalled by pressing a numeric key from 0 to 9. Remote Operation 6 Remote Operation 6.1Interfaces The instrument is programmable by a PC. Functions and ranges can be selected and measurement values stored in the instrument can be read out. The respective drivers are available on the enclosed Product CD or can be downloaded at http://www.hameg.com. The Dual Interface USB/RS-232 HO820 and the GPIB interface HO880 are electrically isolated from the measuring circuit. RS-232 Interface Only three wire lines are connected inside: ❙❙ pin 2 = Txd (transmit data) ❙❙ pin 3 = Rxd (Receive data) ❙❙ pin 5 = Gnd (Ground) Electric voltage on Rxd must be according to the RS-232 hardware standard (+12/-12 V max). This provides the capability to communicate with any PC computer via a COM port. The communication protocol is a Xon/Xoff procedure. The command #X1 activates a software handshake. Now, the transmission between PC and interface is not synchronised via the hardware handshake and operates as follows. XON = 11h = transmission continue XOFF = 13h = transmission hold Once the instrument has received a command line (refer to the definition below), it sends the Xoff character (19 dec). After all commands (in the received line) have been computed and executed, it sends the Xon character (17 dec), making the transmission of a new line possible. Commands are the same for all interfaces (For more details concerning the optional interfaces refer to the corresponding manual). With the receipt of a remote command, the display shows: The user may return to local mode by pressing the context sensitive keys 5 below the LOCAL option (all other keys are locked). By sending the command LK1, the user may lock all keys and in this case the display shows: To establish a basic communication a serial cable (1:1) as well as a terminal program like Windows HyperTerminal is required. The Windows HyperTerminal program is part of any Windows operating system. A detailed instruction how to setup a basic communication using HyperTerminal is available at the HAMEG Knowledge Base at http://www. hameg.com/hyperterminal. USB interface You do not have to change the configuration. If required, the baud rate can be changed. Connect the HM8135 with your PC using a USB cable and install the USB drivers like described in the manual of the USB interface HO820. GPIB interface Connect the HM8135 with your PC using a GPIB cable. It is necessary to set the GPIB adress of the HM8135 to the desired value. The adress is changed at the interface on the rear panel. Do this settings only before starting the instrument. It is not possible when the instrument is running. 6.2 Retrofit or change the interface If you wish to change or retrofit the remote interface of the HM8135, please follow the manual of the interface for the installation and jumper settings. In addition to these instructions, you need to program the HM8135 in order to activate the new interface. Please send one of the following commands over the extra built in RS-232 interface: InterfaceCommand USB (HO870/HO820) 813xcom2default:1 IEEE/GPIB (HO880) 813xcom2default:2 RS-232 (HO890) 813xcom2default:3 In order to deactivate all second interfaces please send: 813xcom2default:0 6.3 Commands supported General There are two kinds of commands. The first one is the set of old commands which are HM8133-2 compatible. They are normally understood by the instrument without changing existing programs. The second one is a new set with a similar syntax to the SCPI standard. We recommend to use these commands which are the only one described hereafter. Commands are sent by lines to the instrument, one line being a set of characters in ASCII code between 20 and 127 (dec), and terminated by an end of line terminator (10 dec) or 13 following by 10 (dec). Each line is composed of one or several simple commands (elementary) separated one another by the ”;” (semicolon) separator. Example: :POWER 7 ; :FREQ 500E+6 ; :OUTP ON The level is at +7 dBm, the frequency at 500 MHz and the output signal ON. The strings of data are not case sensitive. That means lower case and upper case are the same. A simple command gives an access to a quantity or a function of the instrument. All commands acting on the 41 Remote Operation same quantity are brought together in a tree structure. We are going to detail function by function beginning with the simplest and the most useful. 6.4 Commands description Syntax conventions The following syntax conventions are valid: ❙❙ lower cases in keywords are optional, for example the keyword OUTPut may be transmitted as OUTP (short writing) or OUTPUT (long writing) ❙❙ [ ] The keyword in brackets is optional ❙❙ | Exclusive OR between several parameters ❙❙ NR1 A string of digits without decimal point (1234) ❙❙ NR2 A string of digits with a decimal point (1234.56) ❙❙ NR3 A string representing a decimal number with an exponent (1234.56E+3) Initialisation *RST idem key ESC at power on time except beep, display, com and memory config (0 – 9) which are not modified 6.5 General commands *IDN? Identification *SAV x Saving the current configuration (x from 0 to 9) *RCL x Recall a configuration (x from 0 to 9) SNR? Serial number of the instrument FAB? Manufacture date of the instrument 6.6 Bus commands LK0 Enable local mode LK1 Disable local mode (all buttons locked) RM0 Disable remote mode RM1 Enable remote mode 6.7 Sound commands BP0 Beep off BPS Soft beep BPL Loud beep 6.8OUTPUT Commands in order to activate the RF output signal Syntax: :OUTPut[:STATe] 0 | OFF | 1 | ON (1) :OUTPut[STATe]?(2) Sending line (1) activates or deactivates the RF output. The parameters 0 or OFF turn off the RF output (if the output is ON), 1 or ON turn on the RF output. Sending line (2) the instrument returns the output state of the instrument. It sends back 1 for output ON and 0 for output OFF. Examples: :OUTP ON Ouput ON :OUTP 1 Ouput ON :OUTPUT ON Ouput ON :OUTPUT:STATE 1 Ouput ON :OUTP? Request for state :OUTPUT:STATE? Request for state 42 6.9 POWER commands Commands in order to change the level of the RF output signal Syntax: :POWer[:LEVel] <NUM>(1) :POWer[:LEVel]?(2) :POWer:UNIT V | DBM (3) :POWer:UNIT?(4) Sending line (1) modifies the level. The <NUM> parameter is a NR2 number (see paragraph Syntax conventions). No unit has to follow the number, the current unit is assumed. Sending line (2) the instrument returns the current level. The instruments sends back a NR2 number corresponding to the resolution without the unit. Sending line (3) changes the current unit. Two parameters are possible: V for Volt (mV / µV included) or DBM for dBm. Sending line (4) the instruments returns the current unit. The instruments sends back the same string as the corresponding command parameters above (e.g. DBM). Examples: :POW:UNIT DBM :POWER:UNIT DBM :POW 5.7 :POW:LEV 5.7 :POWER:UNIT? Set the level unit dBm Set the level unit dBm Set the level to 5.7 dBm Set the level to 5.7 dBm Request for unit 6.10 FREQUENCY commands Commands in order to change the frequency Syntax: :FREQuency[:CW|:FIXed] <NUM> (1) :FREQuency[:CW|:FIXed]? (2) Sending line (1) modifies the carrier frequency. The <NUM> parameter is a NR1 or NR2 or NR3 number (see paragraph Syntax conventions). No unit has to follow the number, the Hz unit is the default one. The value is rounded (same as the keypad) to the resolution. The CW and FIXed options have no particular effect on the instrument, they are present for compatibility with programs existing in the SCPI standard. Sending line (2) the instrument returns the current (carrier) frequency. The instrument sends back a string representing a NR3 decimal number. Examples: :FREQ 678E+6 :FREQUENCY 34000000 :FREQ? :FREQ:FIX 900E+6 Setting of the frequency to 678 MHz Setting of the frequency to 34 MHz Request for frequency Setting of the frequency to 900 MHz Remote Operation 6.11PHASE Commands in order to select the source of the reference signal Syntax: :PHASe:SOURce INTern | EXTern (1) :PHASe:SOURce?(2) Sending line (1) the current reference can be selected. Only one of the 2 parameters must be present: INTern for turning the internal reference on or EXTern for turning the external reference on. Note: It is strongly advised to check the current state after the command (1) sent. For example with the query command (2). Sending line (2) the instruments returns which source is currently selected. The instrument sends back the strings INT or EXT corresponding to the 2 options described above. Examples: :PHAS:SOURCE EXT Activating the external reference :PHASE:SOUR? Request for current reference :PHAS:SOUR? Request for current reference (abbreviated form) 6.12 PULM (PULse Modulation) Commands in order to modify the GATE modulation. Syntax: :PULM:STATe 1 | ON | 0 | OFF (1) :PULM:STATe?(2) Sending line (1) the GATE modulation can be activated or deactivated. The parameters 1 or ON turn the modulation on and 0 or OFF turn the modulation off (if present). Sending line (2) the instruments returns the state of the GATE modulation. The instrument sends back 0, if the modulation is switched off, and 1, if the modulation is online. Syntax conventions). No unit has to follow the number, % unit is the default one. If the value has an accuracy higher than the resolution (0.1%), the number is rounded to the resolution. Sending line (2) the instrument returns the current depth of modulation. The instruments sends back a NR2 number corresponding to the resolution (one digit after the decimal point) without unit. :AM:SOURce INTern | EXTern (3) :AM:SOURce?(4) Sending line (3) the modulation source can be selected and the FM will be turned on. Sending line (4) the instrument returns the source modulation. The instrument sends back the strings INT or EXT (not INTERN or EXTERN). If the AM is turned off, the string INT is sent back because this source is the default setting for the command AM:STAT 1 . :AM:INTern:FREQuency <NUM> (5) :AM:INTern:FREQuency?(6) Sending line (5) the frequency of the internal modulation signal can be changed. The <NUM> parameter is a NR1 or NR2 or NR3 number (see paragraph Syntax conventions). No unit has to follow the number, Hz unit is the default one. The value is rounded to the resolution. Sending line (6) the instruments returns the current modulation frequency. The instrument sends back a string representing a NR3 decimal number. :AM:INTern:SHAPe SIN | SQU | TRI | +RP | -RP (7) :AM:INTern:SHAPe?(8) :PULM:POLarity NORMal | INVert (3) :PULM:POLarity?(4) Sending line (7) the shape of the internal modulation signal can be changed.The parameters are: SIN for a sine signal, SQU for square, TRI for triangle, +RP for a positive ramp and –RP for a negative ramp. Sending line (3) the validation level of the GATE modulation can be set. The parameter NORMal represents high level validation and INVert represents low level validation. Sending line (8) the instrument returns the current shape. The instrument sends back the same strings as the corresponding command parameters above. Sending line (4) the instrument returns the current level state. The instrument sends back 1 for high level (NORMal) and 0 for low level (INVert). :AM:STATe 0 | OFF | 1 | ON (9) :AM:STATe?(10) 6.13 AM (Amplitude Modulation) Commands in order to modify AM parameters Syntax: :AM[:DEPTh] <NUM>(1) :AM[:DEPTh]?(2) Sending line (1) the modulation depth can be modified. The <NUM> parameter is a NR2 number (see paragraph Sending line (9) the AM modulation can be turned on or off. Sending the parameters 1 or ON, AM will be turned on, and sending the parameters 0 or OFF, the modulation will be turned off (if present). Sending line (10) the instrument returns the current AM state. The instrument sends back 0, if no AM is in progress, and 1, if AM is present. Example: :AM:INT:FREQ 3000; SHAP SQU; DEPT 60; STAT 1 43 Remote Operation 6.14 FM (Frequency Modulation) Commands in order to modify FM parameters Syntax: :FM[:DEViation] <NUM>(1) :FM[:DEViation]?(2) Sending line (1) the FM deviation can be modified. The <NUM> parameter is a NR1 or NR2 or NR3 number (see paragraph Syntax conventions). No unit has to follow the number, Hz unit is the default one. The value is rounded to the resolution. Sending line (2) the instrument returns the current FM deviation. The instrument sends back a string representing a NR3 decimal number. :FM:SOURce INTern | EXTern (3) :FM:SOURce?(4) Sending line (3) the modulation source is set and the FM is turned on at the same time. Sending line (4) the instrument returns the FM source. The instrument sends back the strings INT or EXT (not INTERN or EXTERN). If the FM is turned off, the string INT is sent back because the internal source is the default setting for the command FM:STAT 1 . :FM:INTern:FREQuency <NUM> (5) :FM:INTern:FREQuency?(6) Sending line (5) the frequency of the internal modulation signal can be changed. The <NUM> parameter is a NR1 or NR2 or NR3 number (see paragraph Syntax conventions). No unit has to follow the number, Hz unit is the default one. The value is rounded to the resolution. Sending line (6) the instrument returns the current modulation frequency. The instrument sends back a string representing a NR3 decimal number. :FM:INTern:SHAPe SIN | SQU (7) :FM:INTern:SHAPe?(8) Sending line (7) the shape of the internal modulation signal can be changed. The parameters are: SIN for a sine signal, SQU for square. Sending line (8) the instrument returns the current shape. The instrument sends back the same strings as the corresponding command parameters above. :FM:STATe 0 | OFF | 1 | ON (9) :FM:STATe?(10) Sending line (9) the FM can be turned on or off. The FM is turned on by sending parameters 1 or ON and the parameters 0 or OFF turn the modulation off (if present). 44 Sending line (10) the instrument returns the current FM state. The instrument sends back 0, if no FM is in progress, and 1, if FM is present. :FM:EXTern:COUPling AC | DC (13) :FM:EXTern:COUPling?(14) Sending line (13) the external FM modulation is set to AC or DC mode. Sending line (14) the instrument returns the current state. The instrument sends back the same strings as the corresponding command parameters above. Example: FM:INT:FREQ 9E+3; SHAP SIN; DEV 150E+3; STAT ON 6.15 PM (Phase Modulation) Commands in order to modify PM parameters Syntax: :PM[:DEViation] <NUM>(1) :PM[:DEViation]?(2) Sending line (1) the PM deviation can be modified. The <NUM> parameter is a NR2 number (see paragraph Syntax conven-tions). No unit has to follow the number, the current unit is the default one. If the value has an accuracy higher than the resolution, the number is rounded to the corresponding digit. Sending line (2) the instrument returns the current PM deviation. The instrument sends back a string representing a NR2 decimal number (without unit). :PM:UNIT RAD | DEG (3) :PM:UNIT?(4) Sending line (3) the current unit of the phase can be changed. Two parameters are possible: RAD for radian or DEG for degree. Sending line (4) the instrument returns the current unit. The instrument sends back the same strings as the corresponding command parameters above. :PM:SOURce INTern | EXTern (5) :PM:SOURce?(6) Sending line (5) the modulation source can be selected and at the same time the PM is turned on. Sending line (6) the instrument returns the PM source. The instrument sends back the strings INT or EXT (not INTERN or EXTERN). If the PM is turned off, the string INT is sent back because the internal source is the default setting for the PM:STAT 1 command. :PM:INTern:FREQuency <NUM> (7) :PM:INTern:FREQuency?(8) Remote Operation Sending line (7) the frequency of the internal modulation signal can be changed. The <NUM> parameter is a NR1 or NR2 or NR3 number (see paragraph Syntax conventions). No unit has to follow the number, Hz unit is the default one. The value is rounded to the resolution. Sending line (8) the instrument returns the current modulation frequency. The instrument sends back a string representing a NR3 decimal number. :PM:INTern:SHAPe SIN | SQU (9) :PM:INTern:SHAPe?(10) Sending line (9) the shape of the internal modulation signal can be changed. The parameters are: SIN for a sine signal, SQU for square. Sending line (10) the instrument returns the current shape. The instrument sends back the same strings as the corresponding command parameters above. :PM:STATe 0 | OFF | 1 | ON (11) :PM:STATe?(12) Sending line (11) the PM can be turned on or off. The PM is turned on by sending the parameters 1 or ON and it is turned off by sending 0 or OFF (if present). :FSKey :F1 <NUM>(5) :FSKey :F1?(6) Sending line (3) and (5) the two frequencies F0 and F1 can be changed. The <NUM> parameter is a NR1 or NR2 or NR3 number (see paragraph Syntax conventions). No unit must follow the number, Hz unit is the default one. The value is rounded to the resolution. Sending line (4) and (6) the instrument returns the two frequencies F0 and F1. It sends back a string representing a NR3 decimal number. :FSKey :STATe 0|OFF|1|ON (7) :FSKey :STATe?(8) Sending line (7) the FSK can be turned on or off. The FSK is turned on by sending the parameters 1 or ON, and it is turned off by sending 0 or OFF (if present). Sending line (8) the instrument returns the current FSK state. The instrument sends back 0, if no FSK is in progress, and 1, if FSK is present. Example: :FSK:SOUR EXT ; F0 400E+6 ; F1 410E+6 ; STAT ON Sending line (12) the instrument returns the current PM state. The instrument sends back 0, if no PM is in progress, and 1, if PM is present. 6.17PSK Commands in order to modify PSK parameters. Syntax: :PSKey :SOURce EXT (1) :PSKey :SOURce ? (2) :PM:EXTern:COUPling AC | DC (13) :PM:EXTern:COUPling?(14) Sending line (1) the modulation source can be changed (for this unit version always EXT). Sending line (13) the external PM modulation is set to AC or DC mode. Sending line (2) the instrument returns the PSK source. It sends back the string EXT (not EXTERN). Sending line (14) the instrument returns the current state. The instrument sends back the same strings as the corresponding command parameters above. Example: :PM:UNIT DEG; DEV 120; INT:FREQ 1E+3; SHAP SIN; STATE 1 :PSKey :PH0 <NUM> (3) :PSKey :PH0? (4) :PSKey :PH1 <NUM> (5) :PSKey :PH1? (6) 6.16FSK Commands in order to modify FSK parameters Syntax: :FSKey :SOURce EXT (1) :FSKey :SOURce ? (2) Sending line (3) and (5) the two phases PH0 and PH1 can be changed. The <NUM> parameter is a NR2 number (see paragraph Syntax conventions). No unit must follow the number, the current unit is the default one. If the value has an accuracy higher than the resolution, the number is rounded to the corres-ponding digit. Sending line (1) the modulation source can be changed (for this unit version always EXT). Sending line (4) and (6) the instrument returns the two phases PH0 and PH1. It sends back a string representing a NR2 decimal number (without unit). Sending line (2) the instrument returns the FSK source. It sends back the string EXT (not EXTERN). :PSKey :UNIT RAD|DEG (7) :PSKey :UNIT? (8) :FSKey :F0 <NUM>(3) :FSKey :F0?(4) Sending line (7) the current unit can be changed. Two parameters are possible: RAD for radian or DEG for degree. 45 Remote Operation Sending line (8) the instrument returns the current unit. It sends back the same string as the corresponding command parameters above. :PSKey :STAT 0|OFF|1|ON (9) :PSKey :STAT? (10) Sending line (9) the PSK can be turned on or off. The PSK is turned on by sending the parameters 1 or ON, and it is turned off by sending 0 or OFF (if present). Sending line (10) the instrument returns the current FSK state. The instrument sends back 0, if no PSK is in progress, and 1, if PSK is present. Example: :PSK:SOUR EXT ; UNIT RAD ; PH0 0 ; PH1 10 ; STAT ON 6.18SWEEP Commands in order to modify SWEEP parameters. Syntax : :FREQuency:MODE SWEep (1) :FREQuency :MODE FIXed | CW (2) :FREQuency :MODE ? (3) Sending line (9) the instrument returns the sweep TIME. It sends back a string representing a NR2 decimal number. Example: :SWE :TIME 5;:FREQ:STAR 16E+6;:FREQ:STOP 1.2E+9; :FREQ :MODE SWE 6.19SYSTEM Syntax: :SYSTem:ERRor? Sending this line the instrument returns the current error code. This code is the first one recorded even if several errors have occured. After sending the error number the instrument sets it to zero (it also set it to zero at power on time). Refer to the table of the error codes. Notes regarding the syntax As mentioned in some examples above, in each command line the first character ”:“ is optional. In case of successive commands corresponding to the same tree it is not necessary to repeat all the descriptions of the commands. Example: FM:INT:FREQ 9E+3; SHAP SIN; DEV 150E+3; STAT ON Sending line (1) the SWEEP can be turned on. Sending line (2) the SWEEP can be turned off, if SWEEP is present. Sending line (3) the instrument returns the current SWEEP state. It sends back SWE, if SWEEP is in progress, and FIX, if no SWEEP is present. :FREQuency:STARt <NUM> (4) :FREQuency:STARt?(5) :FREQuency:STOP <NUM> (6) :FREQuency:STOP?(7) Sending line (4) and (6) the two frequencies START and STOP can be changed. The <NUM> parameter is a NR1 or NR2 or NR3 number (see paragraph Syntax conventions). No unit must follow the number, Hz unit is the default one. The value is rounded to the resolution. is the same as: :FM:INT:FREQ 9E+3; :FM:INT:SHAP SIN; :FM:DEV 150E+3; STAT ON In fact: FM for the first command indicates that we get into the FM tree (group) and the following commands, if they belong to the same group, may be shorter (without repeating all the tree descriptions). If the next command does not belong to the same tree, it is necessary to specify the root. 6.20 Error codes and their meaning 00 No error 01 Direct Digital Synthesis error (Hardware) 02 Internal reference error (Hardware) 03 External reference error (Hardware) 04 PLL1 error (Hardware) 05 PLL2 error (Hardware) Sending line (5) and (7) the instrument returns the two frequencies START and STOP. It sends back a string representing a NR3 decimal number. 08 Calibration error 15 Level error (out of range) :SWEep :TIME <NUM>(8) :SWEep :TIME?(9) 16 (Carrier) Frequency error (out of range) 21 AM modulation in progress (impossible to turn another modulation on) Sending line (8) the sweep TIME can be changed. The <NUM> parameter is a NR2 number (see paragraph Syntax conven-tions). No unit must follow the number, sec. unit is the default one. The value is rounded to the resolution. 09 Overload error (Hardware) 22 PM modulation in progress (impossible to turn another modulation on) 23 FM modulation in progress (impossible to turn another modulation on) 25 46 AM depth error (out of range) Remote Operation 62 FM deviation error (must be in the range 2 kHz - 400 kHz) 63 FM deviation error (must be in the range 1 kHz-200 kHz) 64 FM deviation error (must be in the range 200 Hz-150 kHz) 70 AM frequency modulation error (must be in the range 10 Hz-20 kHz) 71 AM frequency modulation error (must be in the range 10 Hz-40 kHz) 75 PM deviation error (in remote control, no phase <0) 76 frequency error (in remote control, no frequency <0) 81 FM or PM frequency modulation error (must be in the range 10 Hz-20 kHz) 82 FM or PM frequency modulation error (must be in the range 10 Hz-100 kHz) 90 PM deviation error (must be in the range 0 rad – 3.14 rad) 91 PM deviation error (must be in the range 0 rad - 10.00 rad) 92 PM deviation error (must be in the range 0 deg - 180.0 deg) 93 PM deviation error (must be in the range 0 deg - 573.0 deg) 102 Syntax or Parameter error (remote control) 103 Invalid Separator (remote control) 110 Command header error (remote control) 120 Numeric data error (remote control) 47 Amplitude modulation (Level ≤+7 dBm) Amplitude modulation (Level ≤+7 dBm) Internal or external Source: 3 GHz RF-Synthesizer HM8135 Internal or external Source: Amplitude modulation (Level ≤+7 0…100 %dBm) AM-depth: 3 GHz RF-Synthesizer HM8135 Technical DataAlldatavalidat23°Cafter30minuteswarm-up. 0…100 %dBm) Internal or external AM-depth: Source: Amplitude modulation (Level 0.1 %≤+7 Resolution: 3 GHz RF-Synthesizer HM8135 Alldatavalidat23°Cafter30minuteswarm-up. 0.1% %≤+7 0…100 %dBm) Resolution: AM-depth: Internal or external Source: Amplitude modulation (Level ±4 displayed rate ±0.5 % Accuracy: Alldatavalidat23°Cafter30minuteswarm-up. 3 GHz RF-Synthesizer HM8135 ±4 % displayed rate ±0.5 %kHz) 0.1 %≤+7 Accuracy: Resolution: 0…100 %dBm) AM-depth: Internal or ≤80 external Source: Amplitude modulation (Level (AM-depth %, fmod ≤50 Alldatavalidat23°Cafter30minuteswarm-up. 3 GHz RF-Synthesizer HM8135 ±4 % displayed ratefAC ±0.5 %kHz) (AM-depth ≤80 %, ≤50 Accuracy: Amplitude modulation (Level 0.1 %≤+7 Resolution: 0…100 %dBm) Internal orkHz external AM-depth: Source: mod 10 Hz…100 for Frequency V.S.W.R. Ext.frequencyresp.(to-1dB): f ≤1 GHz ≤1.5; Alldatavalidat23°Cafter30minuteswarm-up. 3 GHz RF-Synthesizer HM8135 Internal orkHz external Source: 10 % Hz…100 for (AM-depth ≤80 %, fAC Ext.frequencyresp.(to-1dB): ±4 displayed rate ±0.5 %kHz) Frequency Accuracy: Amplitude modulation (Level 0.1 %≤+7 0…100 %dBm) Resolution: AM-depth: mod <2 (AM-depth ≤60 %,≤50 fmod 1 Hz…3 GHz ≤1 kHz) Distortion: Range: f >1 GHz ≤2.5 3 GHz RF-Synthesizer HM8135 Alldatavalidat23°Cafter30minuteswarm-up. 0…100 %dBm) Amplitude modulation (Level ≤+7 AM-depth: <2 % (AM-depth ≤60 %,≤50 fmod Hz…3 GHz ≤1 kHz) 10 Hz…100 for Distortion: Range: Ext.frequencyresp.(to-1dB): Internal orkHz external Source: (AM-depth ≤80 %, fAC Frequency ±4 displayed rate ±0.5 %kHz) 0.1 % Accuracy: Resolution: mod mod 11 Hz <6 (AM-depth ≤80 %, f <20 kHz) Resolution: Amplitude modulation (Level ≤+7 dBm) Alldatavalidat23°Cafter30minuteswarm-up. 3 GHz RF-Synthesizer HM8135 Modulation sources Internal external Source: 0.1 %(AM-depth Resolution: Hzms GHz <2 % ≤60 %,≤50 fmod 1 Hz…3 ≤1 <6 Hz…100 ≤80 <20kHz) kHz) Resolution: Distortion: 0…100 %orkHz Range: AM-depth: 10 for AC Ext.frequencyresp.(to-1dB): (AM-depth ≤80 %, f kHz) Frequency ±4 displayed rate ±0.5 % Accuracy: <10 Settlingtime: mod Internal or external Source: Amplitude modulation (Level ≤+7 dBm) 3GHz GHzRF-Synthesizer RF-Synthesizer HM8135 Alldatavalidat23°Cafter30minuteswarm-up. 0…100 % AM-depth: ±4 displayed rate ±0.5 % Accuracy: ms GHz 1<10 Hz <6 % (AM-depth ≤80 %, f <20 kHz) Settlingtime: 0.1 % Resolution: Resolution: <2 ≤60 Hz…3 ≤1 kHz) Distortion: Range: 10 Hz…100 kHz for AC Ext.frequencyresp.(to-1dB): (AM-depth ≤80 %, f ≤50 kHz) mod Frequency 3 HM8135 mod 110Amplitude Hz…200 kHzmodulation sine wave, Internal AM-depth: Frequency modulation (Level ≤+7 0…100 %dBm) Internal Source: 3Settlingtime: GHz HF-Synthesizer Alldatavalidat23°Cafter30minuteswarm-up. 0.1 %p(AM-depth Resolution: (AM-depth ≤80 <10 ms GHz S% eor cexternal iexternal f i c%, afAC t±0.5 i o≤50 n s<20 ±4 displayed rate %kHz) Accuracy: 1 Hz <6 ≤80 %, fmod kHz) Frequency modulation Resolution: <2 ≤60 Hz…3 ≤1 kHz) 10% Hz…100 kHz for Distortion: Range: mod Ext.frequencyresp.(to-1dB): internal or Alldatavalidat23°Cafter30minuteswarm-up. 10 Hz…20 kHz modulation square wave, triangle, sawtooth Source: Frequency 10 MHz Amplitude (Level ≤+7 dBm) Internal or external 3Reference GHz RF-Synthesizer HM8135 Source: 0.1 Resolution: 0…100 % AM-depth: HM8135 ±4 displayed rate ±0.5 % Accuracy: 10 Hz…100 kHz for AC Ext.frequencyresp.(to-1dB): internal or external Source: (AM-depth ≤80 %, f ≤50 kHz) Frequency 3 GHz RF-Synthesizer HM8135 <10 ms Reference 10 MHz Frequency modulation Settlingtime: 1 Hz <6 % (AM-depth ≤80 %, f <20 kHz) <2 ≤60 Hz…3 GHz ≤1 kHz) Resolution: Distortion: Range: mod ±200 Hz…400 kHz Amplitude modulation (Level ≤+7 dBm) Standard:TCXO Deviation: Internal or external mod Source: 0…100 % Alldatavalidat23°Cafter30minuteswarm-up. AM-depth: ±4 % rate ±0.5 % Accuracy: 0.1 %%displayed Resolution: Resolution 10 Hz (AM-depth ≤80 %, fAC kHz) 3Reference GHz RF-Synthesizer HM8135 <2 (AM-depth ≤60 %,≤50 fmod 1 Hz…3 ≤1 Distortion: ±200 Hz…400 kHz Range: internal orexternal external Standard:TCXO Deviation: Source: 10 Hz…100 kHz for Ext.frequencyresp.(to-1dB): Alldatavalidat23°Cafter30minuteswarm-up. Frequency 10 MHz mod <10 Frequencymodulation modulation(Level Hzms GHz Settlingtime: mod <6 ≤80 <20kHz) kHz) Resolution: Amplitude ≤+7 dBm) Internal or Source: (depending on frequency band) Temperaturestability 0…100 % AM-depth: 0.1 % Resolution: (AM-depth ≤80 %, f ≤50 kHz) ±410 %Hz…100 displayed rate ±0.5 % Accuracy: mod GHz RF-Synthesizer HM8135 kHz for AC ExternalSource: Ext.frequencyresp.(to-1dB): Alldatavalidat23°Cafter30minuteswarm-up. 1 Hz <6 (AM-depth ≤80 %,% fmod <20 kHz) All data valid at 233 °C after 30 minutes warm-up.. Resolution: ±200 Hz…400 kHz (depending on frequency band) Temperaturestability Standard:TCXO Deviation: <2 ≤60 Hz…3 GHz ≤1 kHz) Amplitude ≤+7 Distortion: Range: internal external Source: Internal oror external Frequency Reference 10 MHz <10 ms Settlingtime: Frequencymodulation modulation(Level 0…100 %dBm) ≤±0.5 ppm AM-depth: 100 Hz Resolution: 0.1 %% (0…50°C): Resolution: ±4 % displayed rate ±0.5 Accuracy: 10 Hz…100 kHz for AC Ext.frequencyresp.(to-1dB): Frequency (AM-depth ≤80 %, f ≤50 kHz) mod 3Reference GHz RF-Synthesizer HM8135 Alldatavalidat23°Cafter30minuteswarm-up. <2 ≤60 Hz…3 GHz ≤1 kHz) ≤±0.5 ppm Distortion: Range: Internal oror≤80 external <10 ms Source: Settlingtime: 100 (depending onkHz frequency band) Resolution: Temperaturestability 1 Hz (0…50°C): <6 %Hz (AM-depth ≤80 %, fmod <20 kHz) Resolution: ±200 Hz…400 Standard:TCXO Deviation: internal external 0…100 % Source: AM-depth: Frequency 101MHz 0.1 % Frequency modulation Resolution: ≤±1 ppm/year ±3 % + residual FM (f ≤5 kHz) Frequency Aging: Accuracy: ±4 % displayed rate ±0.5 % Accuracy: Impedance 10 kΩ II 50 pF (AM-depth %, f ≤50 kHz) mod mod <2 % (AM-depth ≤60 %, f Hz…3 GHz ≤1 kHz) Distortion: Range: 10<6 Hz…100 kHz for≤80 AC %,mod Ext.frequencyresp.(to-1dB): Frequency 3Reference GHz RF-Synthesizer HM8135 Alldatavalidat23°Cafter30minuteswarm-up. 1 Hz (AM-depth f <20 kHz) ≤±0.5 ppm Resolution: 0…100 % AM-depth: ≤±1 ppm/year ±3 % + residual FM (f ≤5 kHz) 100 Hz Aging: Accuracy: Resolution: <10 ms (0…50°C): Frequency modulation Settlingtime: (depending on frequency band) Temperaturestability mod ±200 Hz…400 kHz 0.1 % internal or external Standard:TCXO Deviation: Resolution: Source: mod ±4 % displayed rate ±0.5 % Frequency 10 MHz Accuracy: ±7 % + residual FM (5 kHz <f <100 kHz) Option:OCXO (HO85) (AM-depth ≤80 %, f ≤50 kHz) 10 Hz…100 kHz for AC Ext.frequencyresp.(to-1dB): Frequency 1 Hz % (AM-depth ≤80 %, fmod kHz) Resolution: Range 1 Hz…3 GHzGHz scale Input level 2 Vpp for full<6 <2 ≤60mod Hz…3 ≤1mod kHz) Distortion: Range: mod <20 Alldatavalidat23°Cafter30minuteswarm-up. <10 ppm/year ms Settlingtime: 0.1 %%displayed internal or external Resolution: ≤±0.5 ppm Source: ≤±1 ±3 + residual FM (f kHz) ±7 (5≤50 kHz <f <100 kHz) Option:OCXO (HO85) Aging: Accuracy: Frequency Reference 10<10 MHz 100 Hz Resolution: (0…50°C): Frequency modulation ±4 % rate ±0.5 %≤5 (depending onkHz frequency band) ±200 Hz…400 Temperaturestability Accuracy: Standard:TCXO Deviation: mod mod (AM-depth ≤80 %, f kHz) Temperaturestability Ext.frequencyresponse:(to-1dB): 10 Hz…100 kHz for AC Ext.frequencyresp.(to-1dB): Frequency mod <2 % (AM-depth ≤60 %, f 1 Hz…3 GHz ≤1 kHz) Distortion: Range: mod ms Settlingtime: Hz <6±200 % displayed (AM-depth ≤80±0.5 %, fmod <20 kHz) Resolution: Resolution Hz1MHz CouplingAccuracy: AC or DC (AM-depth -8 ±4 % rate % Hz…400 kHz Frequency modulation Standard:TCXO Deviation: ±7 (5≤50 kHz <f <100 kHz) Temperaturestability Ext.frequencyresponse:(to-1dB): Option:OCXO (HO85) internal or external Source: ≤±0.5 ppm ≤±1 ppm/year ±3 %Hz + kHz residual FM (f ≤5 kHz) Aging: Accuracy: Frequency Reference1 10 100 ≤80 %, f kHz) Resolution: (depending on frequency band) (0…50°C): Temperaturestability mod 10 Hz…100 kHz for AC ≤±1x 10 Ext.frequencyresp.(to-1dB): mod 0…100 Frequency DCcoupling: <2 ≤60 Hz…3 GHz ≤1 kHz) mod Distortion: Range: 1 Hz <6 % (AM-depth ≤80 %, f <20 kHz) Resolution: mod mod Frequency modulation <10 ms10-9 Settlingtime: -8 internal or external ≤±1x Source: (AM-depth ≤80 %, fAC kHz) (depending on frequency band) Frequency Reference<10 10<10 MHz Temperaturestability 0…100 DCcoupling: Temperaturestability Ext.frequencyresponse:(to-1dB): ±200 Hz…400 kHz Standard:TCXO Deviation: ±7 (5≤50 kHz <f <100 kHz) ≤±0.5 ppm Option:OCXO (HO85) Settling time ≤±1 ppm/year ±3 + kHz residual FM (f ≤5 kHz) 10 Hz…100 kHz for 100 Hz Aging: Accuracy: Ext.frequencyresp.(to-1dB): mod Output (Front panel) Resolution: (0…50°C): Frequency <2 %%Hz…100 (AM-depth ≤60 %, fmod 1ms Hz…3 GHz ≤1 kHz) Distortion: Range: mod ≤±1x 10 kHz /day mod ACcoupling: Hzms <6 ≤80 <20 kHz) Resolution: Settlingtime: internal or external Source: Frequency Reference 10 MHz Frequency modulation 100…100 -8 -9 ≤±0.5 ppm ±200 Hz…400 kHz Standard:TCXO ≤±1x 10 Deviation: Hz…100 kHz for AC 100 Hz Ext.frequencyresp.(to-1dB): Resolution: Hz…100 kHz /day kHz ACcoupling: DCcoupling: (0…50°C): (depending on frequency band) Frequency Temperaturestability Temperaturestability Ext.frequencyresponse:(to-1dB): <2 %%Hz…400 (AM-depth %, fkHz Hz…3 GHz ≤1 kHz) ±7 +for residual FM (5 kHz <f <100 kHz) ≤±1 ppm/year ±3 (fmod ≤5 kHz) Option:OCXO (HO85)10 MHz 1<10 Range: Aging: Accuracy: Hzms <6 ≤80 <20 Resolution: <1 deviation ≥50 at 1kHz) kHz (rear panel) Distortion: Internalreferenceoutput: mod mod Settlingtime: mod Frequency modulation Frequency Reference Level Distortion: 2 Vpp ±200 kHz≤60 Standard:TCXO Deviation: internal or external Source: Frequency Reference 10 MHz -8 -9 (depending on frequency band) Temperaturestability ≤±0.5 ppm <2 ≤60 Hz…3 GHz ≤1 kHz) ≤±1 ppm/year ±3 % + residual FM≥10 (f ≤5 kHz) Distortion: Range: Accuracy: <1 for deviation ≥50 kHz at 1kHz) kHz (rear panel) ≤±1x 10 100 Hz…100 kHz /day Distortion: Internalreferenceoutput: Aging: ACcoupling: Hz Resolution: 0…100 kHz DCcoupling: (0…50°C): 1 Hz <6 % (AM-depth ≤80 %, fkHz <20 Temperaturestability Ext.frequencyresponse:(to-1dB): mod Resolution: ±7 (5mod kHz <f <100 kHz) Option:OCXO (HO85) <10 ms Settlingtime: TTL <3 % for deviation Level: mod mod Frequency modulation internal or external Source: Frequency Reference 10 MHz (depending on frequency band) Temperaturestability ±200 Hz…400 kHz Standard:TCXO Deviation: Temperature Standard TCXO; Option OCXO (HO85) Impedance 1 kΩ -8 -9 ≤±0.5 ppm 100 Hz Resolution: (0…50°C): 1 (rear Hz <6 %%Hz…400 (AM-depth ≤80 %, fkHz <20 kHz) ±7 (5 kHz <f <100 kHz) Resolution: Option:OCXO (HO85) TTL <1 for deviation ≥50 at 1 kHz (rear panel) <3 ≥10 Level:stability ≤±1 ppm/year Distortion: Internalreferenceoutput: ±3 + residual FM (f ≤5 kHz) Accuracy: ≤±1x 10 Hz…100 kHz /day Aging: ACcoupling: 0…100 kHz <10 ms DCcoupling: Settlingtime: mod mod Temperaturestability Ext.frequencyresponse:(to-1dB): mod panel) Frequency modulation Externalreferenceinput: internal or external Source: Frequency Reference 10 MHz ±200 kHz Standard:TCXO Deviation: ≤±0.5 ppm-9 100 Hz Resolution: (0…50°C): (depending on frequency band) Temperaturestability -8 ≤±1 ppm/year ±3 + kHz residual FM≥10 (f ≤5<f kHz) Accuracy: <10 ms Amplitude modulation (Level -30 . . .+7dBm)) Settlingtime: Temperaturestability Ext.frequencyresponse:(to-1dB): TTL <3 %Hz…400 for kHz Externalreferenceinput: Level: ±7 (5mod kHz <100 kHz) Option:OCXO (HO85) <1 ≥50 at 1 kHz (rear panel) Distortion: Internalreferenceoutput: ≤±1x 10 100 Hz…100 kHz /day≤±1 x 10-8 0…100 Aging: ACcoupling: 0…50 °C ≤±0,5 ppm; DCcoupling: (0…50°C): Frequency modulation internal ordeviation external mod Source: >0 dBm Frequency Reference 10 MHz Level: ±200 Standard:TCXO Deviation: Phase modulation (depending on frequency band) Temperaturestability ≤±1 ppm/year ±3 % + residual FM (f ≤5 kHz) Aging: Accuracy: ≤±0.5 ppm 100 Hz mod Resolution: (0…50°C): -8 -9 ≤±1x 10 ±7 %Hz…400 + kHz residual FM≥10 (5 kHz <f <100 kHz) Option:OCXO (HO85) 0…100 >0 MHz dBm DCcoupling: (rear panel) (0…50°C): Externalreferenceinput: Frequency modulation Temperaturestability Ext.frequencyresponse:(to-1dB): TTL <3 for deviation kHz Phase modulation Level: ≤±1 ppm/year; ≤±1 x 10-9/day Aging mod <1 ≥50 at 1 kHz internal or external 100 Hz…100 /day Distortion: Internalreferenceoutput: Source: Aging: ACcoupling: Frequency Reference 10 MHz ±200 kHz Standard:TCXO Deviation: 10 ±20 ppm internal or external Frequency: Source: (depending on frequency band) Temperaturestability ≤±0.5 ppm Source internal or external 100 Hz Resolution: (0…50°C): ±7 % + residual FM (f (5mod kHz Option:OCXO (HO85) ≤±1 ppm/year ±3 ≤5<f kHz) Aging: Accuracy: mod <100 kHz) -8 -9 Temperaturestability Ext.frequencyresponse:(to-1dB): internal or external ≤±1x 10 100 Hz…100 kHz /day Source: 10 MHz ±20 ppm internal or external Aging: ACcoupling: >0 dBm Frequency: Source: Level: 0…100 kHz Frequency Reference 10 MHz DCcoupling: (rear panel) (0…50°C): Phase modulation Externalreferenceinput: TTL ±200 Hz…400 kHz <3 % for deviation ≥10 kHz <1 ≥50 at 1 kHz Standard:TCXO Deviation: Distortion: Internalreferenceoutput: (depending on frequency band) Temperaturestability ≤±0.5 ppm Deviation: 100% Resolution: (0…50°C): ≤±1 ppm/year + residual FM ≤5<f kHz) Aging: Accuracy: mod Temperaturestability Ext.frequencyresponse:(to-1dB): Internal reference output AM depth 0…100 % ±3 ±7 %Hz + for residual FM (f (5 kHz Option:OCXO (HO85) -8 mod <100 kHz) -9 0…100 kHz DCcoupling: (0…50°C): ±200 kHz <1 %Hz…400 deviation ≥50 kHz at 1 kHz (rear panel) Standard:TCXO Deviation: Distortion: Internalreferenceoutput: 10 MHz ppm internal or external Deviation: Frequency: Source: ≤±1x 10 100 kHz /day Aging: ACcoupling: >0 dBm Level: Phase modulation (depending on frequency band) TTL ≤±0.5 ppm Externalreferenceinput: Temperaturestability <3 ≥10 -8 ±20 100 Resolution: (0…50°C): <16 MHz: 0…3.14 rad ≤±1 ppm/year ±3 (f ≤5 Aging: Accuracy: Spectral purity (without ≤±1x modulation) ±7 %Hz +Hz…100 residual FM (5 kHz <fkHz) Option:OCXO (HO85) mod 10 mod <100 kHz) 0…100 kHz DCcoupling: (0…50°C): Temperaturestability Ext.frequencyresponse:(to-1dB): -9 Level TTL Resolution 0,1 % ≤±1x 10 100 Hz…100 kHz /day Aging: ACcoupling: TTL (depending on frequency band) <3 % for deviation ≥10 kHz Temperaturestability <16 MHz: 0…3.14 rad Deviation: <1 ≥50 at 1 kHz Distortion: Internalreferenceoutput: 10 MHz ±20 ppm internal or external ≤±0.5 ppm Spectral purity (without modulation) Frequency: Source: >0 dBm 100 Hz (rear panel) Level: Resolution: (0…50°C): Externalreferenceinput: Phase modulation ≤±1 ppm/year ±3 % + residual FM (f ≤5 kHz) -9 Aging: Accuracy: ≤-35 dBc >16 MHz: 0…10 rad Harmonics: ±7 (5 kHz <f -8 Option:OCXO (HO85) mod Temperaturestability ≤±1x 10 /day Ext.frequencyresponse:(to-1dB): mod <100 kHz) 100 Hz…100 Aging: ACcoupling: 0…100 kHz kHz DCcoupling: (0…50°C): ≤±0.5 ppm <1 ≥50 at 1<100 kHz kHz) Distortion: Internalreferenceoutput: -8 ±20 100 Hz (rear panel) Resolution: ≤-35 dBc Externalreferenceinput: >16 MHz: 0…10 rad <16 0…3.14 rad (0…50°C): Harmonics: TTL <3 %+rad for deviation ≥10 kHz Level: Spectral purity (without modulation) Deviation: 10 MHz ppm internal or external ≤±1 ppm/year ±3 % residual FM (f ≤5 kHz) >0 dBm External reference input Frequency: Source: Aging: Accuracy: 1 kHz, f>16 MHz Accuracy ±5 % @ f Phase modulation ±7 (5 kHz <f Option:OCXO (HO85) ≤-50 dBc (>15 kHz from carrier) 0.01 Non-harmonics: Resolution: mod Temperaturestability Ext.frequencyresponse:(to-1dB): mod ≤±1x 10 -9 mod 0…100 kHz DCcoupling: (0…50°C): <1 % for deviation ≥50 kHz at 1 kHz (rear panel) Distortion: Internalreferenceoutput: ≤±1x 10 100 Hz…100 kHz /day Aging: ACcoupling: -8 ±20 TTL <3 % for deviation ≥10 kHz ≤±1 ppm/year ±3 (f ≤5 kHz) >0 dBm Aging: Accuracy: ≤-50 (>15 kHz from carrier) Level: 0.01 rad ≤-35 dBc >16 MHz: 0…10 rad -9 Non-harmonics: Resolution: Harmonics: (rear panel) Phase modulation Externalreferenceinput: <16 0…3.14 rad Spectral purity (without modulation) 10 MHz ppm ±7 % + residual FM (5 kHz <f <100 internal or external Deviation: mod Option:OCXO (HO85) Frequency: Source: Temperaturestability Ext.frequencyresponse:(to-1dB): ≤±1x 10 ≤-50 dBc ±5 % to 1 kHz + residual PM Sub-harmonics: Accuracy: 0…100 kHz mod DCcoupling: (0…50°C): 100%Hz…100 kHz ≥10 /day Aging: ACcoupling: LevelLevel: >0 dBm Ext. frequency resp. (to -1 dB) 10 Hz…100 kHz for ACdeviation TTL <3 for kHz at 1 kHz kHz) <1 ≥50 (rear panel) Distortion: Internalreferenceoutput: -8 ±20 -9 (rear panel) Externalreferenceinput: 10 MHz ppm internal external ±7 % residual (5 kHz <f <100 kHz) Option:OCXO Frequency: ±5 %+for to 1or kHz +FM residual ≤-50 dBc (>15 kHz from carrier) Source: 0.01 rad Sub-harmonics: Accuracy: Non-harmonics: >0 dBm Resolution: Level: (HO85) ≤-35 >16 MHz: 0…10 rad Harmonics: Phase modulation <16 0…3.14 rad Temperaturestability Ext.frequencyresponse:(to-1dB): Deviation: Spectral purity (without (rear modulation) 0…100 kHz DCcoupling: (0…50°C): (at 20 kHz from carrier) Phasenoise: Ext.frequencyresponse(to-1dB): ≤±1x 10 100 Hz…100 kHz /day Aging: ACcoupling: <1 % deviation ≥50 kHzPM atmod 1 kHz Distortion: Internalreferenceoutput: panel) Externalreferenceinput: TTL <3 % ≤60 for %, deviation ≥10 Level: Frequency 10 MHz ±20 ppm -8 -9 ≤1 kHz)kHz Distortion <2 % (AM-depth fkHz >0 dBm Level: purity (without mod Phase modulation Temperaturestability Ext.frequencyresponse:(to-1dB): (at 20 kHz from carrier) ≤-50 dBc Deviation: ±5 % to 1 kHz + residual PM Phasenoise: Ext.frequencyresponse(to-1dB): Sub-harmonics: 10 MHz ±20 ppm Accuracy: internal or external Frequency: Source: (>15 kHz from carrier) 0.01 rad ≤±1x 10 Non-harmonics: Resolution: ≤-35 >16 MHz: 0…10 rad 0…100 kHz <16 0…3.14 rad Harmonics: DCcoupling: (0…50°C): 100 Hz…100 /day Spectral modulation) Aging: ACcoupling: ≤-120 dBc/Hz 0…100 kHz f<16MHz: DCcoupling: <1 % for deviation ≥50 kHz at 1 kHz (rear panel) Distortion: Internalreferenceoutput: TTLdBm <3 ≥10 >0 Level: Phase modulation (rear panel) Externalreferenceinput: -8 -9 kHz) <6 % (AM-depth ≤80 %, fkHz 10 MHz ±20 ppmcarrier) internal external mod Frequency: Source: Spectral purity purity (without modulation) 0…100 kHz <16 MHz: 0…3.14 rad ≤-120 dBc/Hz DCcoupling: (at 20 kHz from 0…100 kHz (0…50°C): f<16MHz: Phasenoise: DCcoupling: Ext.frequencyresponse(to-1dB): Spectral (without modulation) Deviation: ≤-50 dBc ±5 % to 1or kHz +<20 residual Sub-harmonics: Accuracy: (>15 0.01 rad ≤±1x 10 100 /day ≤-35 >16 0…10 rad Non-harmonics: Resolution: Aging: ACcoupling: Harmonics: <1 ≥50 at 1 kHz Distortion: Internalreferenceoutput: ≤-95 dBc/Hz 100 Hz…100 kHz 16MHz≤f<250MHz: ACcoupling: TTL <3 %Hz…100 for deviation ≥10 kHzPM Level: (rear panel) Externalreferenceinput: 10 MHz ±20 ppmkHz from carrier) internal or external Frequency: Source: >0 dBm Level: Phase modulation -9 Deviation: ≤±1x 10 100 Hz…100 kHz /day ≤-35 >16 MHz: 0…10 rad ≤-95 dBc/Hz Aging: ACcoupling: Harmonics: ≤-120 dBc/Hz 100 Hz…100 kHz 0…100 kHz 16MHz≤f<250MHz: f<16MHz: ACcoupling: DCcoupling: <16 0…3.14 rad (at 20 kHz from carrier) Phasenoise: Ext.frequencyresponse(to-1dB): Spectral purity (without modulation) ≤-50 dBc ±5 % to 1 kHz + residual PM <1 % for deviation ≥50 kHz at 1 kHz = 10 rad (rear panel) (>15 kHz from carrier) 0.01 rad Sub-harmonics: Accuracy: Distortion: Internalreferenceoutput: Non-harmonics: Resolution: TTL <3 ≥10 Level: ≤-105 dBc/Hz <3 for f = 1 kHz and deviation 250MHz≤f<500MHz: Distortion: Externalreferenceinput: Harmonics ≤-30 dBc (typ. <-35 dBc) >0 dBm Frequency modulation mod Phase modulation Deviation: 10 MHz ±20 ppm internal or external Frequency: Source: <16 MHz: 0…3.14 rad <1100 ≥50and at 1 kHz = 10 rad (rear panel) (>15 from carrier) 0.01 rad Spectral purity (withoutTTL modulation) ≤-105 Distortion: Internalreferenceoutput: Non-harmonics: ≤-95 dBc/Hz <3 for Resolution: Hz…100 kHz =+1residual kHz deviation 250MHz≤f<500MHz: 16MHz≤f<250MHz: Distortion: ≤-35 ACcoupling: >16 0…10 rad Harmonics: ≤-120 dBc/Hz 0…100 kHz f<16MHz: DCcoupling: (at 20 kHz fromkHz carrier) ≤-50 dBc <3 %%for deviation ≥10 kHzPM ±5 to 1fkHz Phasenoise: Ext.frequencyresponse(to-1dB): Level: Sub-harmonics: Accuracy: mod Externalreferenceinput: ≤-100 500MHz≤f<1000MHz: >0 dBm Phase modulation 10 MHz ±20 ppm internal or external Frequency: <16 MHz: 0…3.14 rad Spectral purity (without modulation) Non-harmonics ≤-50 dBc (>15 kHz from carrier) Deviation: Source Source: internal or external ≤-35 >16 MHz: 0…10 rad Harmonics: TTL ≤-50 dBc ±5 to 1fkHz <3 %%Hz…100 for deviation ≥10and kHzPM ≤-100 Level: Sub-harmonics: ≤-105 dBc/Hz Accuracy: <3 for =+1residual kHz deviation = 10 rad 500MHz≤f<1000MHz: (rear 250MHz≤f<500MHz: (>15 kHz from carrier) Distortion: 0.01 rad Non-harmonics: Resolution: 100 kHz 16MHz≤f<250MHz: ACcoupling: ≤-120 0…100 kHz panel) (at 20 kHz from carrier) f<16MHz: DCcoupling: Externalreferenceinput: Phasenoise: Ext.frequencyresponse(to-1dB): mod >0 dBm ≤-95 dBc/Hz Phase modulation 1GHz≤f<2GHz: 10 MHz ±20 ppm internal or external Frequency: Source: FSK modulation Deviation: ≤-35 dBc >16 0…10 rad Harmonics: <16 MHz: 0…3.14 rad Spectral purity (without modulation) Sub-harmonics <2,1 GHz ≤-50 dBc (>15 kHz from carrier) 0.01 rad Non-harmonics: Resolution: (rear panel) (at 20 kHz from carrier) Externalreferenceinput: Phasenoise: ≤-100 dBc/Hz Ext.frequencyresponse(to-1dB): 1GHz≤f<2GHz: 500MHz≤f<1000MHz: ≤-50 dBc ±5 to 1fkHz Sub-harmonics: Accuracy: ≤-105 <3 % for =+1residual kHz and PM deviation = 10 rad Deviation ±200 Hz…400 kHz FSK modulation 250MHz≤f<500MHz: Distortion: ≤-95 dBc/Hz 100 Hz…100 kHz >0 dBm ≤-120 16MHz≤f<250MHz: 0…100 kHz ACcoupling: Level: f<16MHz: DCcoupling: Phase modulation 10 MHz ±20 ppm internal or external Frequency: Source: mod ≤-90 16 MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): Deviation: <16 MHz: 0…3.14 rad Spectral purity (without modulation) ≤-50 dBc (>15 kHz from carrier) 0.01 rad Non-harmonics: Resolution: ≤-35 >16 MHz: 0…10 rad Harmonics: ≤-50 dBc ±5 % to 1fkHz +1residual PM Sub-harmonics: Accuracy: >0dBc dBm ≤-120 0…100 kHz ≤-90 Level: f<16MHz: ≤-95 dBc/Hz DCcoupling: 16 MHz…3 GHz 2GHz≤f<3GHz: (depending internal on frequency band) 1GHz≤f<2GHz: (at 20 kHz from carrier) Range(F0…F1): Phase modulation Phasenoise: Ext.frequencyresponse(to-1dB): ≤-100 dBc/Hz 500MHz≤f<1000MHz: FSK modulation ≤-105 <3 for = kHz and deviation = 10 rad 10 MHz ±20 ppm or external 250MHz≤f<500MHz: 100 Hz…100 kHz Distortion: Frequency: Source: 16MHz≤f<250MHz: ACcoupling: Sub-harmonics >2,1 GHz ≤-43 (typ. -47 dBc) Deviation: typ. <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) 2 FSK levels ResidualFM: mod Mode: <16 0…3.14 rad Spectral purity (without modulation) ≤-35 dBc >16 MHz: 0…10 rad Harmonics: ≤-50 dBc (>15 kHz from carrier) ±5 %rad to 1 kHz + residual PM Sub-harmonics: Accuracy: 0.01 Non-harmonics: Resolution: (at 20 kHz from carrier) Phasenoise: Ext.frequencyresponse(to-1dB): 10 MHz ±20 ppm internal orfmod external 100 Hz…100 kHz typ. <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) Frequency: 16MHz≤f<250MHz: Source: ≤-90 dBc/Hz ACcoupling: 2 levels 16 MHz…3 GHz ResidualFM: 2GHz≤f<3GHz: ≤-120 Mode: 0…100 kHz Range(F0…F1): f<16MHz: DCcoupling: ≤-95 1GHz≤f<2GHz: ≤-100 dBc/Hz ≤-105 500MHz≤f<1000MHz: FSK modulation <3FSK % for = 1 kHz and deviation = 10 rad Deviation: 250MHz≤f<500MHz: Distortion: <16 MHz: 0…3.14 rad typ. <0.06 % (in 0.03…20 kHz bandwidth) external Spectral purity (without modulation) ResidualAM: Datasource: ≤-35 >16 0…10 rad Harmonics: ≤-50 dBc (>15 kHz from carrier) 0.01 rad Non-harmonics: Resolution: Phase noise (bei 20 kHz from carrier) (at 20 kHz from carrier) Phasenoise: Resolution 100 Hz Ext.frequencyresponse(to-1dB): ≤-50 dBc ±5 % to 1 kHz + residual PM Sub-harmonics: Accuracy: ≤-120 dBc/Hz 0…100 kHz f<16MHz: DCcoupling: ≤-105 <3 % for fmod 1 kHz and deviation = 10 rad <0.06 %≤6.5 (in 0.03…20 kHz kHz bandwidth) 250MHz≤f<500MHz: Deviation: typ. <4 Hz; Hz (in 0.3…3 bandwidth) Distortion: 2external FSK ResidualAM: ResidualFM: Datasource: 100 Hz…100 kHz Mode: 16MHz≤f<250MHz: ACcoupling: ≤-90 dBc/Hz 16 MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): ≤-95 <16 MHz: 0…3.14 rad ≤-100 1GHz≤f<2GHz: 500MHz≤f<1000MHz: FSK modulation Spectral purity (without modulation) ≤-35 >16 0…10 rad Harmonics: 10 kbit/s Max.rate: (>15 from carrier) 0.01 rad Non-harmonics: Resolution: ≤-50 ±5 % to 1levels kHz += residual PM Sub-harmonics: Accuracy: ≤-120 dBc/Hz 0…100 kHz f<16MHz: DCcoupling: (at 20dBc kHz fromkHz carrier) Phasenoise: Ext.frequencyresponse(to-1dB): fResidualAM: <16 MHz ≤-120 dBc/Hz Accuracy 100 Hz…100 kHz kHz) ±3 % + res. FM (f 16MHz≤f<250MHz: ACcoupling: ≤-100 dBc/Hz <16 0…3.14 rad 500MHz≤f<1000MHz: typ. <0.06 % (in 0.03…20 kHz bandwidth) 10 kbit/s external ≤-105 Max.rate: <3 % for fmod Datasource: 1 kHz and deviation = 10 rad Spectral purity (without modulation) 250MHz≤f<500MHz: Distortion: <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) mod 2 FSK levels ResidualFM: Mode: ≤-90 dBc/Hz 16 MHz…3 GHz ≤-35 dBc >16 MHz: 0…10 rad ≤-95 2GHz≤f<3GHz: Range(F0…F1): Harmonics: 1GHz≤f<2GHz: ≤-50 (>15 kHz from carrier) 0.01 rad FSK modulation Non-harmonics: Resolution: MHz Shift(F1…F0): ±50…10 %Hz…100 tokHz 1≤5 kHz += residual PM Sub-harmonics: Accuracy: (at 20dBc/Hz kHz from carrier) Phasenoise: Ext.frequencyresponse(to-1dB): ≤-95 100 kHz 16MHz≤f<250MHz: ACcoupling: ≤-120 dBc/Hz 0…100 f<16MHz: DCcoupling: ±7 % + res. 0.01 FM (5 kHz <f ≤-105 dBc/Hz <3% % for fmod =<100 1 kHzkHz)) and deviation = 10 rad mod 250MHz≤f<500MHz: Distortion: ≤-35 dBc ≤-95 dBc/Hz >16 MHz: 0…10 rad Harmonics: 1GHz≤f<2GHz: 0…10 MHz 10 kbit/s 16 MHz ≤f <250 MHz ≤-94 dBc/Hz ≤-100 Shift(F1…F0): Max.rate: 500MHz≤f<1000MHz: FSK modulation typ. <0.06 % (in 0.03…20 kHz bandwidth) external ResidualAM: Datasource: <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) 2 FSK levels ≤-50 (>15 kHz from carrier) rad ≤-90 ResidualFM: 16 MHz…3 GHz Mode: Non-harmonics: Resolution: 2GHz≤f<3GHz: Range(F0…F1): ±5 to 1 kHz + residual PM Sub-harmonics: Accuracy: 100 Hz Resolution: (at 20 kHz from carrier) Phasenoise: Ext.frequencyresponse(to-1dB): ≤-120 dBc/Hz 0…100 kHz f<16MHz: DCcoupling: ≤-105dBc/Hz <3 %Hz…100 for fmodkHz = 1 kHz and deviation = 10 rad 250MHz≤f<500MHz: Distortion: ≤-95 100 16MHz≤f<250MHz: ACcoupling: ≤-100 dBc/Hz 500MHz≤f<1000MHz: (>15 kHz from carrier) ≤-90 dBc/Hz 0.01 rad 16 MHz…3 GHz Non-harmonics: 2GHz≤f<3GHz: Resolution: 100 Hz Range(F0…F1): 0…10 MHz ≤-95 Resolution: Shift(F1…F0): 1GHz≤f<2GHz: 10 kbit/s Max.rate: FSK modulation typ. <0.06 % (in 0.03…20 kHz bandwidth) external ≤-50 dBc ±5 % to 1 kHz + residual PM <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) ResidualAM: 2 FSK levels Datasource: Sub-harmonics: Accuracy: ResidualFM: Mode: (at 20 kHz from carrier) Phasenoise: Ext.frequencyresponse(to-1dB): see under FM Accuracy: ≤-120 dBc/Hz 0…100 kHz f<16MHz: DCcoupling: 250500MHz≤f<1000MHz: MHz ≤f <500 MHz ≤-105 dBc/Hz ≤-95 dBc/Hz 100 Hz…100 kHz 16MHz≤f<250MHz: ACcoupling: Ext. frequency response (to -1 dB) ≤-100 dBc/Hz ≤-105 <3 % for fkHz 250MHz≤f<500MHz: Distortion: mod = 1 kHz and deviation = 10 rad ≤-95 1GHz≤f<2GHz: ≤-50 typ. <4 Hz; Hz (in 0.3…3 bandwidth) ±5 % to 1levels 2 FSK Sub-harmonics: FSK modulation ResidualFM: Accuracy: see under FM Mode: 100 Hz ≤-90 dBc/Hz Accuracy: Resolution: 16 MHz…3 2GHz≤f<3GHz: Range(F0…F1): 0…10 MHz Shift(F1…F0): 10 kbit/s (at 20dBc kHz from <0.06 %≤6.5 (incarrier) 0.03…20 kHz kHz bandwidth) external Max.rate: Phasenoise: Ext.frequencyresponse(to-1dB): ResidualAM: Datasource: ≤-120 0…100 kHz f<16MHz: DCcoupling: ≤-95 dBc/Hz 100 Hz…100 kHz 16MHz≤f<250MHz: ACcoupling: ≤-105 dBc/Hz % for fmodGHz =+1residual kHz and PM deviation = 10 rad Distortion: ≤-95 dBc/Hz 1GHz≤f<2GHz: FSK modulation0…100 kHz <3 ≤-100 dBc/Hz 500MHz≤f<1000MHz: 500250MHz≤f<500MHz: MHz ≤f <1.000 MHz ≤-100 dBc/Hz DC coupling ≤-90 dBc/Hz 16 MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): (at 20 kHz from carrier) typ. <0.06 % (in 0.03…20 kHz bandwidth) external Phasenoise: ResidualAM: Ext.frequencyresponse(to-1dB): Datasource: see under FM <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) Accuracy: 2 FSK levels ResidualFM: Mode: 100 Hz Resolution: 0…10 MHz ≤-120 dBc/Hz 0…100 kHz 10 kbit/s Shift(F1…F0): f<16MHz: DCcoupling: Max.rate: ≤-95 dBc/Hz 100 Hz…100 kHz 16MHz≤f<250MHz: ACcoupling: ≤-105 <3 % for f = 1 250MHz≤f<500MHz: Distortion: PSKmodulation modulation ≤-100dBc/Hz dBc/Hz 500MHz≤f<1000MHz: ≤-90 16 MHz…3mod GHz kHz and deviation = 10 rad 2GHz≤f<3GHz: Range(F0…F1): ≤-95 1GHz≤f<2GHz: FSK 1ResidualAM: GHz ≤f <2 GHz ≤-95 dBc/Hz AC coupling 100 Hz…100100 kHz <4 Hz;%≤6.5 Hz (in 0.3…3 bandwidth) 2 FSK levels ResidualFM: Mode: ≤-120 dBc/Hz 0…100 kHz 10 kbit/s f<16MHz: DCcoupling: Max.rate: typ.dBc/Hz <0.06 (in 0.03…20 kHz kHz bandwidth) external Datasource: see under FM PSKmodulation modulation Accuracy: 100 Hz ≤-95 Hz…100 0…10 MHz Resolution: 16MHz≤f<250MHz: ACcoupling: Shift(F1…F0): ≤-105 <3 % for fmodkHz = 1 kHz and deviation = 10 rad 250MHz≤f<500MHz: Distortion: 2 PSK levels Mode: ≤-100 dBc/Hz 500MHz≤f<1000MHz: ≤-95 dBc/Hz 1GHz≤f<2GHz: FSK typ. <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) 2 FSK levels ResidualFM: Mode: ≤-90 dBc/Hz 16 MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): typ. <0.06 % (in 0.03…20 kHz bandwidth) external ResidualAM: Datasource: ≤-95 dBc/Hz 100 Hz…100 kHz 0…10 MHz 16MHz≤f<250MHz: ACcoupling: 2 PSK levels Shift(F1…F0): Mode: 10 kbit/s Max.rate: PSK modulation see under FM ≤-105 dBc/Hz <3 % for fmod = at 1 kHz 100 Hz Accuracy: 250MHz≤f<500MHz: Distortion: Resolution: ≤-100 500MHz≤f<1000MHz: 2 GHz ≤f <3 GHz ≤-90 dBc/Hz external Datasource: ≤-95 dBc/Hz 1GHz≤f<2GHz: FSK modulation<1 % for deviation ≤-90<0.06 16FSK MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): Distortion ≥50 kHz 1 kHzand deviation = 10 rad typ. %≤6.5 (in 0.03…20 kHz kHz bandwidth) external ResidualAM: Datasource: <4 Hz; Hz (in 0.3…3 bandwidth) 2 levels ResidualFM: Mode: 10 kbit/s Max.rate: ≤-105 dBc/Hz <3 % for fmod = 1 kHz and deviation = 10 rad 100 Hz 250MHz≤f<500MHz: Distortion: external Resolution: 2 PSK levels Datasource: Mode: 0…10 MHz Shift(F1…F0): ≤-100 PSK modulation see under FM 500MHz≤f<1000MHz: Accuracy: ≤-95 1GHz≤f<2GHz: 10 kbit/s FSK modulation Max.rate: ≤-90 dBc/Hz 16 MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): typ. <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) 2 FSK levels ResidualFM: Mode: <3 % for deviation ≥10 kHz 10 kbit/s Residual FM typ. <4 Hz; ≤6.5 Hz (in 0.3…3 kHz bandwidth) Max.rate: typ. <0.06 % (in 0.03…20 kHz bandwidth) external ResidualAM: Datasource: 0…10 MHz Shift(F1…F0): ≤-100 dBc/Hz under FM 500MHz≤f<1000MHz: 10 kbit/s Accuracy: Max.rate: Datasource: 100 Hz Resolution: 2see PSK levels Mode: ≤-95 dBc/Hz 1GHz≤f<2GHz: PSKmodulation modulation ≤-90<0.06 FSK 16external MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): typ. <4 Hz;%≤6.5 Hz (in 0.3…3 bandwidth) Shift(Ph1…Ph0): 2 FSK levels ResidualFM: Mode: (in 0.03…20 kHz kHz bandwidth) external ResidualAM: Datasource: 0…10 MHz Shift(F1…F0): 10 kbit/s Max.rate: Residual AM typ. <0.06 % (in 0.03…20 kHz bandwidth) Phase modulation 100 Hz Resolution: ≤-95 1GHz≤f<2GHz: 10 kbit/s Shift(Ph1…Ph0): Max.rate: see under FM FSK modulation Accuracy: external Datasource: 2 PSK levels ≤-90 dBc/Hz 16 MHz…3 GHz Mode: 2GHz≤f<3GHz: Range(F0…F1): <4 Hz;%≤6.5 Hz (in 0.3…3 bandwidth) 2 FSK levels PSKMHz: modulation ResidualFM: Mode: <16 0…±3.14 rad typ. <0.06 (in 0.03…20 kHz kHz bandwidth) external ResidualAM: Datasource: 10 kbit/s Max.rate: 100 Hz Resolution: 0…10 MHz Shift(F1…F0): see under FM Accuracy: ≤-90<4 dBc/Hz 16 MHz…3 GHz 2GHz≤f<3GHz: Range(F0…F1): <16 MHz: 0…±3.14 rad Shift(Ph1…Ph0): PSK modulation 10 kbit/s Max.rate: Source Mode: internal or external external typ. Hz;%≤6.5 (in 0.3…3 bandwidth) 2 FSK levels 2 PSK levels Datasource: ResidualFM: Mode: <0.06 (in Hz 0.03…20 kHz kHz bandwidth) external ResidualAM: Datasource: >16 MHz: 0…±10 rad 10 kbit/s Max.rate: 0…10 MHz FM Shift(F1…F0): see under Accuracy: 100 Hz Resolution: <4 Hz;%≤6.5 Hz (in 0.3…3 bandwidth) 2 FSK levels 2 PSK levels ResidualFM: Mode: >16 MHz: 0…±10 rad Mode: <16 0…±3.14 rad Shift(Ph1…Ph0): PSK modulation 10 kbit/s typ. <0.06 (in 0.03…20 kHz kHz bandwidth) external external Max.rate: ResidualAM: Datasource: Datasource: 10 kbit/s Max.rate: 0.01 rad Resolution: 0…10 MHz Shift(F1…F0): 100 Hz Resolution: Deviation <16 MHz 0…3,14 rad see under FM Accuracy: typ. <0.06 % (in 0.03…20 kHz bandwidth) external external ResidualAM: PSKMHz: modulation Datasource: 0.01 rad Datasource: >16 0…±10 rad Resolution: 2 PSK levels Mode: <16 0…±3.14 rad kbit/s 10 kbit/s Shift(Ph1…Ph0): Max.rate: Max.rate: 0…10 MHz Shift(F1…F0): see under PM Accuracy: 100 Hz Resolution: see under FM Accuracy: >16 MHz PSK modulation0…10 rad 10 2 PSK levels Mode: 10 kbit/s 10 kbit/s Max.rate: see under PM Max.rate: 0.01 radrad Accuracy: Resolution: external Datasource: >16 MHz: 0…±10 <16 0…±3.14 rad 0…10 MHz Shift(F1…F0): Shift(Ph1…Ph0): 100 Hz Resolution: see under FM Accuracy: 2 PSK levels Mode: PSK modulation0,01 rad external Resolution Datasource: 0…10 MHz Shift(F1…F0): Shift(Ph1…Ph0): see under PM Accuracy: 10 kbit/s Max.rate: 0.01 rad Resolution: >16 MHz: 0…±10 rad 100 Hz <16 0…±3.14 rad Resolution: see under FM Accuracy: Pulse modulation PSK modulation external Datasource: 2 PSK levels Mode: 10 kbit/s Max.rate: 100 Hz <16 0…±3.14 rad Resolution: Shift(Ph1…Ph0): see PMPM Pulse modulation Accuracy: 0.01 rad under FM >16 MHz: 0…±10 rad Resolution: Accuracy: external (rear panel) Source: Accuracy ±5 % up to 1see kHz +under residual PSK modulation 2 PSK levels Mode: 10 kbit/s Max.rate: external Datasource: Shift(Ph1…Ph0): see under FM >16 MHz: 0…±10 rad Accuracy: external (rear panel) Source: <16modulation 0…±3.14 rad Pulse modulation see under PM 0.01 rad Accuracy: Resolution: PSK (Typical phase noise at 1 GHz) Dynamicrange: 2 PSK levels Mode: external Datasource: Shift(Ph1…Ph0): Ext. frequency response (to -1 dB) 10 kbit/s Max.rate: <16 0…±3.14 rad 0.01 rad Resolution: external (rear (Typical phase noise at 1 GHz) Dynamicrange: Source: MHz: 0…±10 rad Pulse modulation see under PM panel) Accuracy: PSK modulation 2 PSK levels Mode: f>16 <2 GHz: >80 dB external Datasource: 10 kbit/s Max.rate: <16 MHz: 0…±3.14 rad Shift(Ph1…Ph0): DC coupling 0…100 kHz 2external >16 MHz: 0…±10 rad see under PM panel) f >2 <2modulation GHz: >80 dB Accuracy: (Typical phase noise at 1 GHz) Dynamicrange: 0.01 rad PSK Resolution: (rear Source: PSK levels Mode: modulation Datasource: fPulse GHz: >55 dB 10external kbit/s Max.rate: Output level Shift(Ph1…Ph0): >16 MHz: 0…±10 rad <16 0…±3.14 rad 0.01 rad Resolution: 2 PSK levels Mode: >2 >55 f <2 GHz: >80 dB see under Accuracy: (Typical phase noise at 1 GHz) Output level Dynamicrange: external (rear external Source: Datasource: AC coupling 100 Hz…100 kHz 10 kbit/s Pulse modulation Max.rate: <50 ns (typ. <10panel) ns) -135…+13 dBm Rise/falltimes: Range: Shift(Ph1…Ph0): <16 MHz: MHz: 0…±3.14 rad PM 0.01 radrad Resolution: >16 0…±10 see under PM Accuracy: external Datasource: <50 ns (typ. <10 ns) = 10 rad fPulse >2 GHz: >55 dB -135…+13 dBm Rise/falltimes: Range: modulation <2 >80 Output level 10 kbit/s (Typical phase noise at 1 GHz) 0.1 external (rear panel) Dynamicrange: Max.rate: Source: Shift(Ph1…Ph0): <100 ns dB Delay: <16 0…±3.14 rad Resolution: >16 MHz: 0…±10 rad Distortion <3 % for fmod = 1 kHz and deviation see under PM Accuracy: 0.01 rad (rear Resolution: 10 kbit/s external panel) Max.rate: <100 ns Source: <50 ns (typ. <10 ns) 0.1 dB dB -135…+13 dBm Delay: Rise/falltimes: Resolution: Range: f >2 GHz: >55 dB Pulse modulation <2 >80 Output level (Typical phase noise at 1 GHz) 0.0…30.0 Shift(Ph1…Ph0): Dynamicrange: <16 0…±3.14 rad 2.5 MHz (typ. 5 MHz) in 0.1 dB steps Max.frequency: >16 MHz: 0…±10 rad Display-Offsetforext.Attn.: 0.01under rad PM Resolution: see Accuracy: FSK modulation (Typical phase noise at 1 GHz) 0.1 modulation Shift(Ph1…Ph0): 2.5under MHz (typ. 5panel) MHz) Dynamicrange: <100 ns 0.0…30.0 in 0.1 dB steps dB dB Max.frequency: Delay: external (rear Display-Offsetforext.Attn.: Resolution: Source: <50 ns (typ. ns) -135…+13 dBm Rise/falltimes: Range: fPulse >2 GHz: >55 dB <16 MHz: 0…±3.14 rad <2 >80 Output level >16 0…±10 rad TTL Inputlevel: 0.01 rad Precisionf<1.5GHz;level>-120dBm Resolution: see PM<10 Accuracy: Pulse modulation external (rear Source: <16 0…±3.14 rad <2 >80 Range (F0…F1) 16…3 GHz 0…±10 TTLunder 2.5 MHz (typ. 5 panel) MHz) in 0.1 dB steps Inputlevel: Max.frequency: Precisionf<1.5GHz;level>-120dBm Display-Offsetforext.Attn.: (Typical phase noise at 1 GHz) 0.0…30.0 Dynamicrange: <100 ns 0.1 dBdB dB Delay: Resolution: <50 ns (typ. <10 ns) -135…+13 dBm >16 MHz: rad f >2 GHz: >55 dB Rise/falltimes: Range: 0.01 rad Output level Resolution: for level >-57 dBm: ≤±0.5 see PM Accuracy: external (rear panel) Source: Pulse modulation (Typical phase noise at 1 GHz) 0.1 Dynamicrange: >16 MHz: 0…±10 rad f >2 GHz: >55 dB TTL for level level >-57 dBm: ≤±0.5 Inputlevel: <2 >80 Precisionf<1.5GHz;level>-120dBm Output 2.5 MHz (typ. 5 MHz) in 0.1(-57 dB dBm steps- level))/10) Max.frequency: Display-Offsetforext.Attn.: <100 ns dBdB 0.01 rad <50 ns (typ. <10 ns) Delay: -135…+13 Resolution: Rise/falltimes: Range: see under PM Accuracy: for <-57 ≤±(0.5 dBdB +dBm (0.2x Sweep mode Mode Resolution: 2 FSK levels Pulse modulation (Typical phaselevel noisedBm: at 1 GHz) 0.0…30.0 Dynamicrange: external (rear<10 panel) Source: <2 GHz: >80under 0.01 rad <50 ns ns) -135…+13 Resolution: Rise/falltimes: <-57 dBm: ≤±(0.5 dBdB +dBm (0.2x Range: for levellevel >-57 ≤±0.5 fSweep >2 >55 dB TTL mode Inputlevel: Precisionf<1.5GHz;level>-120dBm Output 2.5 MHz (typ. 5 MHz) 0.0…30.0 in 0.1(-57 dB dBm steps- level))/10) see PM panel) <100 ns(typ. Max.frequency: 0.1 dBdB Display-Offsetforext.Attn.: Accuracy: Delay: Resolution: 1…3000 MHz Range: Precisionf>1.5GHz;level>-120dBm modulation external (rear Source: fPulse <2 GHz: >80 dB Data source external (Typical phase noise 1 GHz) 0.1 dB Typical phase noise at 1at GHz Dynamicrange: f >2 GHz: >55 dB see under PM<10 <100 ns(typ. Accuracy: 1…3000 MHz Output level Delay: Resolution: for level <-57 dBm: ≤±(0.5 dBdB +dBm (0.2x (-57 dBm - level))/10) Range: <50 ns ns) Precisionf>1.5GHz;level>-120dBm -135…+13 Rise/falltimes: Range: >-57 ≤±0.5 dB Sweep mode TTL 2.5 MHz (typ. 5 MHz) Inputlevel: 0.0…30.0 in 0.1 dB steps Precisionf<1.5GHz;level>-120dBm Max.frequency: Display-Offsetforext.Attn.: 500 Hz…2999 MHz Pulse modulation for level dBm: ≤±0.7 Depth: external (rear panel) Source: (Typical phase noise at 1 GHz) Dynamicrange: f >2 GHz: >55 dB Output level <2 >80 Output Max. rate 10 kbit/s <50 ns (typ. <10 ns) -135…+13 dBm Rise/falltimes: Range: 2.5 MHz (typ. 5 MHz) 0.0…30.0 dB in 0.1(-57 dB dBm steps- level))/10) 500 Hz…2999 MHz Max.frequency: 1…3000 MHz Display-Offsetforext.Attn.: forlevel level <-57 dBm: ≤±0.7 Depth: Range: <100 ns Precisionf>1.5GHz;level>-120dBm 0.1 dBdB Delay: Resolution: ≤±(0.5 (0.2x >-57 ≤±0.5 Sweep mode TTL Inputlevel: Precisionf<1.5GHz;level>-120dBm Pulse modulation external (rear panel) Source: 20 ms…5 s for level dBm: ≤±(0.7 dB + (0.5x Sweeptime: (Typical phase noise at 1 GHz) Dynamicrange: <2 GHz: GHz: >80 ns dB (typ. <10 ns) <50 -135…+13 dBm Rise/falltimes: Range: ff >2 >55 dB Output level <100 ns(rear 0.1 dBdBm Delay: Resolution: TTL 20dB ms…5 s panel) Inputlevel: 500 Hz…2999 MHz Precisionf<1.5GHz;level>-120dBm ≤±(0.7 (0.5x forphase level >-57 dBm: ≤±0.7 dB Sweeptime: Depth: 2.5 MHz (typ. 5 MHz) 0.0…30.0 in 0.1(-57 dB dBm steps- level))/10) Pulse modulation Max.frequency: 1…3000 MHz Display-Offsetforext.Attn.: Range: Precisionf>1.5GHz;level>-120dBm Range -135…+13 <-57 ≤±(0.5 dBdB + (0.2x ≤±0.5 Source: Sweep mode 0…10 MHz external Shift (F1…F0) (Typical noise at 1 GHz) Dynamicrange: internal 50 Ω Trigger: <2 >80 Impedance: f >2 GHz: >55 Output level <100 ns 0.1 dB Delay: Resolution: <50 ns (typ. <105ns) -135…+13 dBm Rise/falltimes: Range: 2.5 MHz (typ. MHz) 0.0…30.0 dB in 0.1(-57 dB dBm steps- level))/10) Max.frequency: Display-Offsetforext.Attn.: external (rear ≤±0.5 Source: internal 20 ms…5 s <10panel) 50≤1ΩGHz: forphase level <-57 dBdBm + (0.5x Trigger: Sweeptime: TTL Impedance: Inputlevel: 500 Hz…2999 Precisionf<1.5GHz;level>-120dBm >-57 ≤±0.7 dB Depth: 1…3000 MHz (Typical noisedBm: at 1 GHz) Range: ≤±(0.5 (0.2x Dynamicrange: Precisionf>1.5GHz;level>-120dBm <2 >80 Sweep f≤±(0.7 ≤1.5 f >2 GHz:mode 100 Hz >55 dB V.S.W.R.: Output level <50 ns ns) -135…+13 Rise/falltimes: Range: Resolution 0,1 dB Resolution 2.5 MHz (typ. 5 MHz MHz) 0.0…30.0 in 0.1 dB steps Max.frequency: Display-Offsetforext.Attn.: <100 ns(typ. 0.1 dB dB Delay: Resolution: TTL Inputlevel: Precisionf<1.5GHz;level>-120dBm (Typical phase noise at 1 GHz) ≤±(0.5 (0.2x Dynamicrange: internal f ≤1 GHz: ≤1.5 50 Ω Trigger: V.S.W.R.: Impedance: ≤±0.5 Sweep mode 20 ms…5 s for level <-57 dBm: ≤±(0.7 dB + (0.5x (-57 dBm level))/10) Sweeptime: 500 Hz…2999 MHz f <2 GHz: >80 dB >-57 ≤±0.7 dB 1…3000 MHz Depth: Range: Precisionf>1.5GHz;level>-120dBm >2 >55 Output level f >1 GHz: ≤2.5 <50 ns (typ. <10 ns) -135…+13 dBm Rise/falltimes: Range: Protective functions <100 ns 0.1 dB Delay: Resolution: TTL Inputlevel: Precisionf<1.5GHz;level>-120dBm 2.5 MHz(fmod (typ. 5kHz) MHz) 0.0…30.0 dB0,1 indB 0.1steps dB steps Max.frequency: Display-Offsetforext.Attn.: Display-Offset for ext. Attn. 0,0…30,0 dB in % + residual FM Accuracy ≤±0.5 <2 >80 1…3000 MHz Range: Precisionf>1.5GHz;level>-120dBm f50 ≤1 ≤1.5 >1 ≤2.5 V.S.W.R.: ≤±(0.5 (0.2x internal ΩGHz: Protective functions Trigger: Impedance: Sweep 20 ms…5 s≤5 f >2 GHz: mode >55 dB forlevel level <-57 dBm: ≤±(0.7 dB + in (0.5x (-57steps dBm - level))/10) 500 Hz…2999 Sweeptime: >-57 ≤±0.7 dB Depth: <50 ns (typ. <10 ns) Output level -135…+13 dBm Rise/falltimes: Range: The synthesizer is±3 protected against reverse power applied on RF outp <100 ns 0.1 dB Delay: Resolution: 2.5 MHz (typ. 5 MHz MHz) 0.0…30.0 dB 0.1 dB Max.frequency: Display-Offsetforext.Attn.: for >-57 dBm: ≤±0.5 dB TTL Inputlevel: Precisionf<1.5GHz;level>-120dBm <100 kHz) ±7 % + residual FM (5 kHz <f Precision mod ≤±(0.5 (0.2x f >2 GHz: >55 dB 500 Hz…2999 MHz >-57 ≤±0.7 dB Sweep mode The synthesizer is protected against reverse power applied onV.RF outp Depth: f >1 GHz: ≤2.5 1…3000 MHz Range: Output level Precisionf>1.5GHz;level>-120dBm ≤1 ≤1.5 Protective functions V.S.W.R.: internal <50 ns (typ. <10 ns) 50 Ω -135…+13 dBm 20 ms…5 s Trigger: for level <-57 dBm: ≤±(0.7 dB + (0.5x (-57 dBm level))/10) Rise/falltimes: Impedance: Range: Sweeptime: <100 ns 0.1 dB Delay: Resolution: up to 1 W for a 50 Ω source and against any DC source up to ±7 The pro 2.5 MHz (typ. 5 MHz) 0.0…30.0 dB in 0.1 dB steps Max.frequency: Display-Offsetforext.Attn.: Modulation sources TTL Inputlevel: Precisionf<1.5GHz;level>-120dBm for level <-57 dBm: ≤±(0.5 dB + (0.2x (-57 dBm level))/10) Sweep mode >-57 ≤±0.5 dBdBdBm f V.S.W.R.: <1.5 GHz; level >-120 dBm 1…3000 MHz Range: Precisionf>1.5GHz;level>-120dBm <50 ns (typ. <10 ns) 20 ms…5 sany -135…+13 <-57 ≤±(0.7 (0.5x (-57 dBm - level))/10) PSK modulation Rise/falltimes: Sweeptime: The synthesizer isΩprotected against reverse power applied onV.RF outp Range: up toProtective 1W for a 50 source and against DC source up to ±7 The pr 500 Hz…2999 MHz for level >-57 dBm: ≤±0.7 dBdB+kHz Depth: f >1 GHz: ≤2.5 Modulation sources <100 ns ≤1 ≤1.5 functions 0.1 dB internal 50 Ω Delay: Resolution: Trigger: Impedance: 2.5 MHz (typ. 5 MHz) 0.0…30.0 in 0.1 dB steps Max.frequency: Display-Offsetforext.Attn.: 10 Hz…200 sine wave tection disconnects the output until manually reset by operator. TTL Internal: Inputlevel: Precisionf<1.5GHz;level>-120dBm for level >-57 dBm: ≤±0.5 dB 1…3000 MHz Range: Precisionf>1.5GHz;level>-120dBm for level <-57 dBm: ≤±(0.5 dB + (0.2x (-57 dBm level))/10) Sweep mode for level >-57 dBm dB 500 Hz…2999 >-57dBm: ≤±0.7 dB Depth: <100 ns internal 0.1 dB ΩGHz: Delay: Trigger: Resolution: 10 Hz…200 kHz sine wave Impedance: up toProtective 1W for a 50 source and against DC source to ±7 The pro tection disconnects the output until manually reset applied byupoperator. 20 ms…5 sany5 MHz Internal: forlevel level<-57 <-57 dBm: ≤±0,7 ≤±(0.7 dB +(0.2x (0.5x (-57 dBm -triangle, level))/10) Sweeptime: The synthesizer isΩ protected against reverse power onV.RF outp Modulation sources 2.5 MHz (typ. MHz) 0.0…30.0 dB in 0.1 dB steps f50 >1 ≤2.5 ≤1 ≤1.5 Max.frequency: Display-Offsetforext.Attn.: V.S.W.R.: functions TTL Inputlevel: Precisionf<1.5GHz;level>-120dBm 10 Hz…20 kHz square wave, sawtooth for >-57 ≤±0.5 dB ≤±(0.5 dB + (-57 dBm level))/10) Sweep mode 500 Hz…2999 MHz for level >-57 dBm: ≤±0.7 dB Depth: 1…3000 MHz Precisionf>1.5GHz;level>-120dBm Mode Range: 2 PSK levels 20 ms…5 s for level <-57 dBm dB + dB (0,5kHz xin (-57 dBm -wave, level))/10) forlevel level<-57 <-57dBm: dBm: ≤±(0,7 ≤±(0.7 +(0.2x (0.5x (-57 dBm -triangle, level))/10) Sweeptime: 2.5 MHz MHz (typ. 5 DC MHz) 0.0…30.0 0.1 dB steps ≤1 ≤1.5 Max.frequency: Display-Offsetforext.Attn.: V.S.W.R.: 10 Hz…200 kHz sine wave Hz…20 square sawtooth tection disconnects the output until manually reset applied byupoperator. internal Internal: ΩGHz: Trigger: Impedance: up toMiscellaneous 1W for a 50 source and against source to ±7 The pro The synthesizer isΩ protected against reverse power onV.RF outp TTL Modulation sources Inputlevel: f50 >1 ≤2.5 Precisionf<1.5GHz;level>-120dBm Protective functions >-57 ≤±0.5 dB 10 Hz Resolution: for ≤±(0.5 dBdB (-57 dBm level))/10) Sweep mode 1…3000 Range: Precisionf>1.5GHz;level>-120dBm 20 ms…5 s anyMHz for level <-57 ≤±(0.7 dB ++ (0.5x (-57 dBm -- level))/10) Sweeptime: 500 Hz…2999 >-57 dBm: ≤±0.7 dB Depth: Precision Data source external internal 50 Ω Trigger: Impedance: TTL Inputlevel: f >1 GHz: ≤2.5 Precisionf<1.5GHz;level>-120dBm Hz 10 Hz…20 kHz square wave, triangle, sawtooth Resolution: ≤1 ≤1.5 Protective functions V.S.W.R.: Hz…200 kHz sine wave Miscellaneous tection disconnects the output until manually resetIEEE-488 byupoperator. Internal: up to 1 W for a 50 Ω source and against any DC source to ±7 V.RF The pro for level >-57 dBm: ≤±0.5 dB The synthesizer is protected against reverse power applied on outp Modulation sources <-57 ≤±(0.5 dB + (0.2x (-57 dBm level))/10) USB/RS-232 (HO820), (option) Sweep mode Input on+front panel Interfaces: 1…3000 MHz External: Range: Precisionf>1.5GHz;level>-120dBm 500 Hz…2999 MHz for level level <-57 >-57 dBm: dBm: ≤±0.7 dB Depth: internal 50 Ω Trigger: Impedance: 20 ms…5 s for ≤±(0.7 dB (0.5x (-57 dBm level))/10) Sweeptime: f Internal: >1.5 GHz; level >-120 dBm fInput ≤1 ≤1.5 V.S.W.R.: The synthesizer isΩ10 protected against reverse power applied on RF outp for level >-57 dBm: ≤±0.5 dB USB/RS-232 (HO820), IEEE-488 (option) on front panel 10 HzGHz: Interfaces: External: Resolution: >1 ≤2.5 Miscellaneous Hz…20 kHz square wave, triangle, sawtooth Protective functions Hz…200 kHz sine wave <-57 ≤±(0.5 dB + (0.2x (-57 dBm level))/10) tection disconnects the output until manually reset by operator. up to 1 W for a 50 source and against any DC source up to ±7 V. The pr Sweep mode 1…3000 MHz Modulation sources Range: Precisionf>1.5GHz;level>-120dBm Max. rate kbit/s 10 10 kΩ II 50 pF Configurationmemories: 500 Hz…2999 MHz Impedance: >-57 ≤±0.7 dB Depth: 20 ms…5 s for level <-57 dBm: ≤±(0.7 dB + (0.5x (-57 dBm level))/10) Sweeptime: f ≤1 GHz: ≤1.5 V.S.W.R.: internal 50 Ω Trigger: Impedance: for level >-57<-57 dBm dBm: >1 GHz: ≤2.5 for level ≤±(0.5 dB ++front (0.2x (-57 dBm -- level))/10) up toMiscellaneous 1W for a 50 source and against anyMHz DC source to ±7 V.RF The pr Protective functions 10 USB/RS-232 (option) kΩ II 50 pFscale Input on panel Configurationmemories: Interfaces: The synthesizer isΩ protected against reverse power applied on outp Impedance: External: Sweep mode Modulation sources ≤±0,5 10 Hz Resolution: 1…3000 MHz kHz square wave, triangle, sawtooth Hz…200 kHz sine Range: Precisionf>1.5GHz;level>-120dBm tection disconnects the output until manually resetIEEE-488 byupoperator. Internal: 500 Hz…2999 for level >-57 ≤±0.7 Depth: Safety Class I(HO820), (EN61010-1) 2f dB VHz…20 for full Safetyclass: 20 ms…5 s Inputlevel: <-57 dBm: ≤±(0.7 dB (0.5x (-57wave dBm level))/10) Sweeptime: internal 50 Ω Trigger: Impedance: pp dB f >1 GHz: ≤2.5 Protective functions ≤1 ≤1.5 V.S.W.R.: Shift (Ph1…Ph0) <16 MHz is0…±3,14 rad1…3000 for level <-57>-57 dBmdBm: + (0,2 x (-57 dBmwave -wave, level))/10) The synthesizer against reverse power applied on outp MHz Hz…200 kHz sine Range: tection disconnects the output until manually reset by Safety Class I(HO820), (EN61010-1) 10 Precisionf>1.5GHz;level>-120dBm 2Ω VdB Internal: 10 kΩ IIDC 50 pF for full scale Safetyclass: Configurationmemories: Inputlevel: Impedance: up toMiscellaneous 1W for a 50 Ω protected source and against any DC source upoperator. to ±7 V.RF The pr USB/RS-232 IEEE-488 (option) Input on panel Interfaces: External: Modulation sources ≤±(0,5 500 Hz…2999 MHz Hz for level ≤±0.7 dB Depth: Resolution: Hz…20 kHz square triangle, sawtooth pp 20 ms…5 s <-57 ≤±(0.7 dB +front (0.5x (-57 dBm - level))/10) Sweeptime: 115…230 V ±10 %, 50/60 Hz, CAT II AC or Powersupply: internal Coupling: Trigger: Impedance: ff50 ≤1 GHz: ≤1.5 V.S.W.R.: The Protective synthesizer is protected against reverse power applied on RF outpu >1 Hz…20 GHz: ≤2.5 >16 rad up toMiscellaneous 1W forMHz afunctions 50 Ω0…±10 source and against DC upoperator. to ±7(option) Impedance 500 Hz…2999 MHz >-57 dBm: ≤±0.7 dB Depth: kHz square wave, triangle, sawtooth 115…230 Vany ±10 %,source 50/60IEEE-488 Hz, CAT IIV. The pr Modulation sources 50 Ω≤±(0.7 Safety Class I(HO820), (EN61010-1) 2 VHz…200 AC or DC for full scale Powersupply: Safetyclass: Inputlevel: Coupling: kHz sine tection disconnects the output until manually reset by 10 Internal: 10 kΩ IIpanel 50 pF Configurationmemories: Impedance: USB/RS-232 20 ms…5 sany Input on front panel for level <-57 dB + (0.5x (-57wave dBm - level))/10) Interfaces: Hz Sweeptime: External: Resolution: pp internal Ω Trigger: Impedance: approx. 40 VA Front Powerconsumption: Output: f50 ≤1 GHz: ≤1.5 V.S.W.R.: >1 ≤2.5 functions up toProtective 1 W for a 50 source and against DC source up to ±7 The proModulation sources The synthesizer isΩ protected against power applied onV.RF outpu Hz…200 kHz sine wave tection disconnects the output untilreverse manually by Internal: 20+5…+40 ms…5 s°C for level <-57 dBm: ≤±(0.7 dB + (0.5x (-57 dBm level))/10) 10 Hz Sweeptime: approx. 40 115…230 V VA ±10 %,reset 50/60 Hz,operator. CAT II(option) Resolution: Front panel AC or DC Powerconsumption: Powersupply: Output: Coupling: Hz…20 kHz square wave, triangle, sawtooth Miscellaneous Safety Class I (EN61010-1) 2 V for full scale Safetyclass: Inputlevel: 10 internal kΩ II 50 pF 50 Ω USB/RS-232 (HO820), IEEE-488 Configurationmemories: Input on front panel Trigger: Impedance: Impedance: Interfaces: External: ≤1 ≤1.5 V.S.W.R.: pp Operatingtemperature: Level f >1 GHz: ≤2.5 Protective functions The synthesizer is protected against reverse power applied on RF outpu pp 10 Hz…200 kHz sine wave tection disconnects the output until manually reset byupoperator. Internal: up to 1 W for a 50 Ω source and against any DC source to ±7 V. The proModulation sources Hz…20 kHz square internal USB/RS-232 50≤1 Ω Input on front panel wave, triangle, sawtooth Trigger: +5…+40 °C Interfaces: approx. 40 Impedance: External: Front panel Operatingtemperature: Powerconsumption: Level Hz Output: 115…230 V VA ±10 %, 50/60IEEE-488 Hz,toCAT Resolution: AC orfor DC Powersupply: Coupling: Safety Class I(HO820), (EN61010-1) 2 V full scale f10 GHz: ≤1.5 10 Safetyclass: 10 kΩ II 50 pF Inputlevel: V.S.W.R.: Configurationmemories: ≤2.5 -20…+70 °C functions 1>1 kΩ Storagetemperature: The synthesizer is against reverse power onV.II(option) RF outpu pp Impedance: up toProtective 1Miscellaneous W for a 50 Ω protected source and against any DC source ±7 The proModulation sources Hz…20 kHz square wave, triangle, sawtooth 48 Hz…200 kHz sine wave tection disconnects the output until manually reset applied byupoperator. Internal: Hz Resolution: 10 f ≤1 GHz: ≤1.5 10 kΩ II 50 pF Miscellaneous -20…+70 °C Configurationmemories: +5…+40 °C V.S.W.R.: Impedance: 1 kΩ 2 V Storagetemperature: Operatingtemperature: USB/RS-232 (HO820), IEEE-488 (option) Input on front panel Level Interfaces: approx. 40 VA External: Front panel Powerconsumption: Output: 115…230 V ±10 %, 50/60 Hz, IIRF AC DCfull Safety Class I (EN61010-1) Powersupply: ≤2.5 for scale Coupling: Safetyclass: Inputlevel:sources ppor functions The synthesizer isΩ protected against reverse power applied onV. outpu 5…80 % (non condensing) Rel.humidity: up toProtective 1W for a 50 source and against any DC source toCAT ±7 The proModulation Hz…200 kHz sine wave tection disconnects the output until manually reset byup operator. Internal: 10>1 Hz Resolution: Miscellaneous Hz…20 kHz square wave, triangle, sawtooth USB/RS-232 (HO820), IEEE-488 (option) Input on front panel Interfaces: External: Safety Class Icondensing) (EN61010-1) for full scale f10>1 GHz: ≤2.5 5…80 (non Safetyclass: -20…+70 °C Inputlevel: 110 kΩ Rel.humidity: Storagetemperature: 10 kΩ IIDC 50 pF Impedance: functions Configurationmemories: +5…+40 °C 2 V Operatingtemperature: Level approx. 40 The synthesizer isxΩH protected against reverse power applied on(option) RF output Front 115…230 V ±10 %, 50/60 Hz, Powerconsumption: AC or Output: Powersupply: Coupling: sources up toProtective 1W for a 50 source and against any DC source up toCAT ±7 V.II The propp Modulation Hz…200 kHz sine wave tection disconnects the untilx % manually reset by operator. Internal: 285 75 x VA 365 mm Dimensions(W x D):output Hz…20 kHz square wave, triangle, sawtooth USB/RS-232 (HO820), IEEE-488 Input onpanel front panel Interfaces: External: 10 Hz Resolution: Miscellaneous 10 kΩfor IIpanel 50 pFsquare Configurationmemories: The against reverse applied onV.IIRF outpu 115…230 Vkg ±10 %, 50/60 Hz, AC DC Powersupply: 5…80 (non condensing) Coupling: sources Rel.humidity: Safety Class I power (EN61010-1) full scale Safetyclass: -20…+70 Inputlevel: 110 kΩ Storagetemperature: Impedance: +5…+40 °C V approx. 40 VA up tosynthesizer 1 Wdisconnects for a 50isΩ protected source and against any DC source toCAT ±7 The proOperatingtemperature: Front Level Powerconsumption: Output: Modulation Hz…200 kHz sine wave tection the output until % manually reset byup operator. Internal: ppor 102 Hz…20 kHz wave, triangle, sawtooth approx. 5°C 7 Technical Technical DataData d d d d d d d d d put put oput ooput oput oput put ooput put ot o-t -t utut-t -t Technical Data Resolution 0,01 rad Accuracy ±5 % up to 1 kHz + residual PM Pulse modulation Source Dynamic range external f <2 GHz f >2 GHz >80 dB >55 dB Rise/fall times <50 ns (typ. <10 ns) Delay <100 ns Max. frequency 2.5 MHz (typ. 5 MHz) Input level TTL Sweep mode Range 1…3.200 MHz Depth 500 Hz…2.999 MHz Sweep time 20 ms…5 s Trigger intern Protective functions The synthesizer is protected against reverse power applied to the RF output up to 1 W for a 50 Ω source and against any DC source up to ±7 V. The protection disconnects the output until manually reset by operator. Miscellaneous Interface Dual-Interface USB/RS-232 (HO820), IEEE-488 (GPIB) (optional) Configuration memories 10 Safety class Safety Class I (EN61010-1) Power supply 115/230 V ±10 %, 50…60 Hz, CAT II Power consumption ca. 40 VA Operating temperature +5…+40 °C Storage temperature -20…+70 °C Rel. humidity 5…80 % (non condensing) Dimensions (W x H x D) 285 x 75 x 365 mm Weight approx. 5 kg Accessories supplied Line cord, Operating manual, CD Recommended accessories HO85 OCXO, temperature stability ±1 x 10 -8 (Installation only ex factory) HO880 Interface IEEE-488 (GPIB), galvanically isolated HZ13 Interface cable (USB) 1.8 m HZ14 Interface cable (serial) 1 1 HZ20 Adapter, BNC to 4 mm banana HZ21 Adapter, N male to BNC female HZ24 Attenuators 50 Ω (3/6/10/20 dB) HZ33 Test cable 50 Ω, BNC/BNC, 0.5 m HZ34 Test cable 50 Ω, BNC/BNC, 1.0 m HZ42 19“ Rackmount kit 2RU HZ72 GPIB-Cable 2 m HAMEG Instruments GmbH | Industriestr. 6 | 63533 Mainhausen | Germany | Phone +49 (0) 6182 8000 R&S® is a registered trademark of Rohde & Schwarz GmbHv & Co. KG | HAMEG Instruments® is a registered trademark of HAMEG Instruments GmbH 49 Trade names are trademarks of the owners | Version 02.01 | 09 / 2014 | © HAMEG Instruments GmbH | Data without tolerance limits is not binding | Subject to change Flow Charts Function selection Flow Charts Phi Step control Phi Phi 50 Flow Charts Amplitude Modulation Control FSK PSK GATE 51 Flow Charts Phase Modulation Control FSK 52 PSK GATE Flow Charts Frequency Modulation Control FSK PSK GATE 53 Flow Charts FSK Modulation Control STATUS 400.000000MHz 410.000000MHz FSK Ext 1200.000000MHz F I X 13.0dBm REFint MOD. MOD. * MODULATION MENU * AM FM PM --> * * FSK PARAMETERS F0 F1 On ** MOD. * MODULATION MENU * <- - FSK PSK GATE * * FSK PARAMETERS Off Fsk0: 512.000000 MHz – stp + cur F0 F1 On ** Off Fsk1: 522.000000 MHz – stp + cur ESC 512.000000MHz 522.000000MHz 54 PREV FSK Ext Flow Charts PSK Modulation Control STATUS 1200.000000MHz 13.0dBm PSK Ext 1200.000000MHz F I X 13.0dBm REFint PREV MOD. MOD. * MODULATION MENU * AM FM PM --> * * PSK PARAMETERS PH0 PH1 Psk0: – stp + On ** * * PSK PARAMETERS Off –10.00rad cur MOD. * MODULATION MENU * <- - FSK PSK GATE PH0 PH1 Psk1: – stp + On ** Off 10.00rad cur ESC 1200.000000MHz 13.0dBm PSK Ext 55 Flow Charts Gate Control FSK 56 PSK GATE Flow Charts Main Menu Control Offs Ref Sfc Sweep Disp DISPLAY ADJUST INTERFACE TYPE I3E SERIAL INTERFACE TYPE USB SERIAL INTERFACE TYPE HO890 SERIAL INTERFACE TYPE SERIAL RS232 (DEFAULT) 4800 NONE 8 1 57 Flow Charts Sweep Control STATUS 1200.000000MHz F I X 13.0dBm REFint STATUS PREV MENU 1200.000000MHz F I X 13.0dBm REFint * * * * MAIN ** *** MAIN MENU MENU * **** Offs SWEEP Ref RefSfc SfcSweep PREV MENU * * * * MAIN MENU * * * * Ref *** Sfc Sweep *** SWEEP MENU *** SWEEP MENU *** Param Mode Trig Off Param Mode Trig On * * * SWEEP MENU *** * * * SWEEP MENU *** Start Stop Time Off Start Stop Time On FrLo: 16.000000 MHz * SWEEP MODE MENU * MENU *cur * * SWEEP MENUContinue *** * * * SWEEP – stp + Burst ––> Start Stop Time Off Start Stop Time Fstr: 16.000000 MHz – stp + cur FrHi: 1.200000000 GHz – stp + cur Fstp: 1200.000000 MHz – stp + cur Sweep Count: 10 – val + cur Fstr: 16.000000 MHz – stp + cur Fstp: 1200.000000 ESC MHz – stp + cur 16.000000MHz SWE 1200.000000MHz 5.00s ESC 16.000000MHz SWE 1200.000000MHz 5.00s 58 *** On SWEEP TRIGGER SIGNAL SweepTime: on5.00 oSec ff – val + cur SweepTime: – val + 5.00 Sec cur T a bTlaebsl e s Conversion ρ Conversion ρ Tables V.S.W.R V.S.W.R REFLECTED FACTOR STATIONARY WAVE RATIO reflected factorstationary wave ratio ρ = I ρI VSWR Tables Z–Z —–—0 Z + Z0 I ρI VSWR I ρI 1 + IρI VSWR = —–— 1 – IρI VSWR I ρI VSWR 0.00 1.00 0.25 1.67 0.50 3.00 0.75 7.00 0.01 1.02 0.26 1.70 0.51 3.08 0.76 7.33 0.02 1.04 0.27 1.74 0.52 3.17 0.77 7.70 0.03 1.06 0.28 1.78 0.53 3.26 0.78 8.09 0.04 1.08 0.29 1.82 0.54 3.35 0.79 8.52 0.05 1.11 0.30 1.86 0.55 3.44 0.80 9.00 0.06 1.13 0.31 1.90 0.56 3.55 0.81 9.53 0.07 1.15 0.32 1.94 0.57 3.65 0.82 10.11 0.08 1.17 0.33 1.99 0.58 3.76 0.83 10.76 0.09 1.20 0.34 2.03 0.59 3.88 0.84 11.50 0.10 1.22 0.35 2.08 0.60 4.00 0.85 12.33 0.11 1.25 0.36 2.13 0.61 4.13 0.86 13.29 0.12 1.27 0.37 2.17 0.62 4.26 0.87 14.38 0.13 1.30 0.38 2.23 0.63 4.41 0.88 15.67 0.14 1.33 0.39 2.28 0.64 4.56 0.89 17.18 0.15 1.35 0.40 2.33 0.65 4.71 0.90 19.00 0.16 1.38 0.41 2.39 0.66 4.88 0.91 21.22 0.17 1.41 0.42 2.45 0.67 5.06 0.92 24.00 0.18 1.44 IρI 0.43 VSWR I2.51 ρI 0.68 VSWR I5.25 ρI 0.93 VSWR 0.19 1.47 0.00 0.44 1.00 2.57 0.25 0.69 1.67 5.45 0.50 0.94 3.00 0.20 1.50 0.01 1.53 0.02 1.56 0.03 1.60 0.04 1.63 0.05 0.06 0.07 0.08 0.09 0.10 0.11 0.12 0.13 0.14 0.15 0.16 0.17 0.18 0.19 0.20 0.21 0.22 0.23 0.24 0.45 1.02 0.46 1.04 0.47 1.06 0.48 1.08 0.49 1.11 1.13 1.15 1.17 1.20 1.22 Tables 1.25 1.27 1.30 1.33 1.35 1.38 1.41 1.44 1.47 1.50 1.53 1.56 1.60 1.63 2.64 0.26 2.70 0.27 2.77 0.28 2.85 0.29 2.92 0.30 0.31 0.32 0.33 0.34 0.35 0.36 0.37 0.38 0.39 0.40 0.41 0.42 0.43 0.44 0.45 0.46 0.47 0.48 0.49 0.70 1.70 0.71 1.74 0.72 1.78 0.73 1.82 0.74 1.86 1.90 1.94 1.99 2.03 2.08 2.13 2.17 2.23 2.28 2.33 2.39 2.45 2.51 2.57 2.64 2.70 2.77 2.85 2.92 5.67 0.51 5.90 0.52 6.14 0.53 6.41 0.54 6.69 0.55 0.56 0.57 0.58 0.59 0.60 0.61 0.62 0.63 0.64 0.65 0.66 0.67 0.68 0.69 0.70 0.71 0.72 0.73 0.74 0.95 3.08 0.96 3.17 0.97 3.26 0.98 3.35 0.99 3.44 3.55 3.65 3.76 3.88 4.00 4.13 4.26 4.41 4.56 4.71 4.88 5.06 5.25 5.45 5.67 5.90 6.14 6.41 6.69 0.21 0.22 0.23 0.24 54 I27.57 ρI 32.33 0.75 39.00 0.76 49.00 0.77 65.67 0.78 99.00 0.79 199.00 0.80 0.81 0.82 0.83 0.84 0.85 0.86 0.87 0.88 0.89 0.90 0.91 0.92 0.93 0.94 0.95 0.96 0.97 0.98 0.99 VSW 7.00 7.33 7.70 8.09 8.52 9.00 9.53 10.1 10.7 11.5 12.3 13.2 14.3 15.6 17.1 19.0 21.2 24.0 27.5 32.3 39.0 49.0 65.6 99.0 199.0 54 Subject to change without Subject to change without notice notice 59 Tables Tables Conversion dBm Conversion dBm Volt Conversion dBm Conversion dBm V0 = Volt Volt Conversion Volt dBm dBm Volt R · P0 · 10 Conversion Volt V0 PdBm = 20 log –––––— R · P0 PdBm ––— 20 with: PO = 1mW and R = 50 Ohm, dBm +20.0 Volt dBm Volt with: PO = 1mW and R = 50 Ohm, with: and R = 501.411 Ohm, 2.236 PO = 1mW +16.0 dBm Volt dBm Volt dBm Volt +12.0 0.890 +8.0 0.562 +4.0 0.354 +19.9 2.210 +15.9 1.395 +11.9 0.880 +7.9 0.555 +3.9 0.350 +19.8 2.185dBm +15.8Volt dBm 1.379 +11.8Volt dBm 0.870 +7.8Volt dBm 0.549 +3.8Volt dBm 0.346 +19.7 +20.0 2.160 2.236 +15.7 +16.0 1.363 1.411 +11.7 +12.0 0.860 0.890 +7.7 +8.0 0.543 0.562 +3.7 +4.0 0.342 +19.6 2.135 +19.9 +15.6 2.210 1.347 +15.9 +11.6 1.395 0.850 +11.9 +7.6 0.880 0.536 +7.9 +3.6 0.555 0.338 +3.9 +19.5 2.111 +19.8 +15.5 2.185 1.332 +15.8 +11.5 1.379 0.840 +11.8 +7.5 0.870 0.530 +7.8 +3.5 0.549 0.335 +3.8 +19.4 2.087 +19.7 +15.4 2.160 1.317 +15.7 +11.4 1.363 0.831 +11.7 +7.4 0.860 0.524 +7.7 +3.4 0.543 0.331 +3.7 +19.3 2.063 +19.6 +15.3 2.135 1.302 +15.6 +11.3 1.347 0.821 +11.6 +7.3 0.850 0.518 +7.6 +3.3 0.536 0.327 +3.6 +19.2 2.039 +19.5 +15.2 2.111 1.287 +15.5 +11.2 1.332 0.812 +11.5 +7.2 0.840 0.512 +7.5 +3.2 0.530 0.323 +3.5 +19.1 2.016 +19.4 +15.1 2.087 1.272 +15.4 +11.1 1.317 0.803 +11.4 +7.1 0.831 0.506 +7.4 +3.1 0.524 0.320 +3.4 +19.0 1.993 +15.0 1.257 +11.0 0.793 +7.0 0.501 +3.0 0.316 +18.9 +18.8 +18.7 +18.6 +18.5 +18.4 +18.3 +18.2 +18.1 +18.0 +17.9 +17.8 +17.7 +17.6 +17.5 +17.4 +17.3 +17.2 +17.1 +17.0 +16.9 +16.8 +16.7 +16.6 +16.5 +16.4 +16.3 +16.2 +16.1 +19.3 +19.2 1.948 +19.1 1.925 +19.0 1.903 +18.9 1.881 +18.8 1.860 +18.7 1.839 +18.6 1.818 +18.5 1.797 +18.4 1.776 +18.3 1.756 +18.2 1.736 +18.1 1.716 +18.0 1.696 +17.9 1.677 +17.8 1.658 1.639 +17.7 1.620 +17.6 1.601 +17.5 1.583 +17.4 1.565 +17.3 1.547 +17.2 1.529 +17.1 1.512 +17.0 1.494 +16.9 +16.9 1.477 +16.8 +16.8 1.460 +16.7 +16.7 1.444 +16.6 +16.6 1.427 +16.5 +16.5 +16.4 +16.4 +16.3 +16.3 +16.2 +16.2 +16.1 +16.1 1.970 2.063 2.039 +14.8 2.016 +14.7 1.993 +14.6 1.970 +14.5 1.948 +14.4 1.925 +14.3 1.903 +14.2 1.881 +14.1 1.860 +14.0 1.839 +13.9 1.818 +13.8 1.797 +13.7 1.776 +13.6 1.756 +13.5 1.736 +13.4 +13.3 1.716 +13.2 1.696 +13.1 1.677 +13.0 1.658 +12.9 1.639 +12.8 1.620 +12.7 1.601 +12.6 1.583 +12.5 1.565 1.565 +12.4 1.547 1.547 +12.3 1.529 1.529 +12.2 1.512 1.512 +12.1 1.494 1.494 1.477 1.477 1.460 1.460 1.444 1.444 1.427 1.427 +14.9 +15.3 +15.2 1.229 +15.1 1.215 +15.0 1.201 +14.9 1.187 +14.8 1.174 +14.7 1.160 +14.6 1.147 +14.5 1.134 +14.4 1.121 +14.3 1.108 +14.2 1.095 +14.1 1.083 +14.0 1.070 +13.9 1.058 +13.8 1.046 1.034 +13.7 1.022 +13.6 1.010 +13.5 0.999 +13.4 0.987 +13.3 0.976 +13.2 0.965 +13.1 0.954 +13.0 0.943 +12.9 +12.9 0.932 +12.8 +12.8 0.921 +12.7 +12.7 0.911 +12.6 +12.6 0.901 +12.5 +12.5 +12.4 +12.4 +12.3 +12.3 +12.2 +12.2 +12.1 +12.1 1.243 1.302 1.287 +10.8 1.272 +10.7 1.257 +10.6 1.243 +10.5 1.229 +10.4 1.215 +10.3 1.201 +10.2 1.187 +10.1 1.174 +10.0 1.160 +9.9 +9.81.147 +9.71.134 +9.61.121 +9.51.108 +9.41.095 +9.31.083 +9.21.070 +9.11.058 +9.01.046 +8.91.034 +8.81.022 +8.71.010 +8.6 0.999 +8.5 0.987 0.987 +8.4 0.976 0.976 +8.3 0.965 0.965 +8.2 0.954 0.954 +8.1 0.943 0.943 0.932 0.932 0.921 0.921 0.911 0.911 0.901 0.901 +10.9 +11.3 +11.2 0.775 +11.1 0.766 +11.0 0.758 +10.9 0.749 +10.8 0.740 +10.7 0.732 +10.6 0.724 +10.5 0.715 +10.4 0.707 +10.3 0.699 +10.2 0.691 +10.1 0.683 +10.0 0.675 0.668+9.9 0.660+9.8 0.652+9.7 0.645+9.6 0.638+9.5 0.630+9.4 0.623+9.3 0.616+9.2 0.609+9.1 0.602 +9.0 0.595 +8.9 +8.9 0.588 +8.8 +8.8 0.581 +8.7 +8.7 0.575 +8.6 +8.6 0.568 +8.5 +8.5 +8.4 +8.4 +8.3 +8.3 +8.2 +8.2 +8.1 +8.1 0.784 0.821 0.812 +6.8 0.803 +6.7 0.793 +6.6 0.784 +6.5 0.775 +6.4 0.766 +6.3 0.758 +6.2 0.749 +6.1 0.740 +6.0 0.732 +5.9 0.724 +5.8 0.715 +5.7 0.707 +5.6 0.699 +5.5 0.691 +5.4 +5.3 0.683 +5.2 0.675 +5.1 0.668 +5.0 0.660 +4.9 0.652 +4.8 0.645 +4.7 0.638 +4.6 0.630 +4.5 0.623 0.623 +4.4 0.616 0.616 +4.3 0.609 0.609 +4.2 0.602 0.602 +4.1 0.595 0.595 0.588 0.588 0.581 0.581 0.575 0.575 0.568 0.568 +6.9 +7.3 +7.2 0.489 +7.1 0.484 +7.0 0.478 +6.9 0.473 +6.8 0.467 +6.7 0.462 +6.6 0.457 +6.5 0.451 +6.4 0.446 +6.3 0.441 +6.2 0.436 +6.1 0.431 +6.0 0.426 +5.9 0.421 +5.8 0.416 0.412 +5.7 0.407 +5.6 0.402 +5.5 0.398 +5.4 0.393 +5.3 0.389 +5.2 0.384 +5.1 0.380 +5.0 0.375 +4.9 +4.9 0.371 +4.8 +4.8 0.367 +4.7 +4.7 0.363 +4.6 +4.6 0.358 +4.5 +4.5 +4.4 +4.4 +4.3 +4.3 +4.2 +4.2 +4.1 +4.1 0.495 0.518 0.512 +2.8 0.506 +2.7 0.501 +2.6 0.495 +2.5 0.489 +2.4 0.484 +2.3 0.478 +2.2 0.473 +2.1 0.467 +2.0 0.462 +1.9 0.457 +1.8 0.451 +1.7 0.446 +1.6 0.441 +1.5 0.436 +1.4 +1.3 0.431 +1.2 0.426 +1.1 0.421 +1.0 0.416 +0.9 0.412 +0.8 0.407 +0.7 0.402 +0.6 0.398 +0.5 0.393 0.393 +0.4 0.389 0.389 +0.3 0.384 0.384 +0.2 0.380 0.380 +0.1 0.375 0.375 0.371 0.371 0.367 0.367 0.363 0.363 0.358 0.358 +2.9 +3.3 +3.2 0.309 +3.1 0.305 +3.0 0.302 +2.9 0.298 +2.8 0.295 +2.7 0.291 +2.6 0.288 +2.5 0.285 +2.4 0.282 +2.3 0.278 +2.2 0.275 +2.1 0.272 +2.0 0.269 +1.9 0.266 +1.8 0.263 0.260 +1.7 0.257 +1.6 0.254 +1.5 0.251 +1.4 0.248 +1.3 0.245 +1.2 0.242 +1.1 0.240 +1.0 0.237 +0.9 +0.9 0.234 +0.8 +0.8 0.231 +0.7 +0.7 0.229 +0.6 +0.6 0.226 +0.5 +0.5 +0.4 +0.4 +0.3 +0.3 +0.2 +0.2 +0.1 +0.1 0.312 Volt 0.354 0.350 0.346 0.342 0.338 0.335 0.331 0.327 0.323 0.320 0.316 0.312 0.309 0.305 0.302 0.298 0.295 0.291 0.288 0.285 0.282 0.278 0.275 0.272 0.269 0.266 0.263 0.260 0.257 0.254 0.251 0.248 0.248 0.245 0.245 0.242 0.242 0.240 0.240 0.237 0.237 0.234 0.234 0.231 0.231 0.229 0.229 0.226 0.226 Subjecttotochange changewithout without notice notice Subject 60 Conversion dBm Conversion dBm Tables mW Conversion mW mW Conversion mW PdBm = 10 log dBm Conversion dBm dBm Conversion dBm PmW –––— P0 PmW = P0 · 10 mW mW PdBm ––— 10 with: PO = 1mW dBm +20.0 mW dBm with: P0 = 1mW 100.000 with: P0 = 1mW +16.0 +19.9 97.724 dBm +20.0 93.325 +20.0 +19.9 91.201 +19.9 +19.8 89.125 +19.8 +19.7 87.096 +19.7 +19.6 85.114 +19.6 83.176 +19.5 +19.5 81.283 +19.4 +19.4 79.433 +19.3 +19.3 77.625 +19.2 +19.2 75.858 +19.1 +19.1 74.131 +19.0 +19.0 72.444 +18.9 +18.9 70.795 +18.8 +18.8 69.183 +18.7 +18.7 67.608 +18.6 +18.6 66.069 +18.5 +18.5 64.565 +18.4 +18.4 63.096 +18.3 +18.3 61.660 +18.2 +18.2 60.256 +18.1 +18.1 58.884 +18.0 57.544 +18.0 +17.9 56.234 +17.9 +17.8 54.954 +17.8 +17.7 53.703 +17.7 52.481 +17.6 +17.6 51.286 +17.5 +17.5 50.119 +17.4 +17.4 48.978 +17.3 +17.3 47.863 +17.2 +17.2 46.774 +17.1 +17.1 45.709 +17.0 +17.0 44.668 +16.9 +16.9 43.652 +16.8 +16.8 42.658 +16.7 +16.7 41.687 +16.6 +16.6 40.738 +16.5 +16.5 +16.4 +16.4 +16.3 +16.3 +16.2 +16.2 +16.1 +16.1 95.499 dBm +19.8 +19.7 +19.6 +19.5 +19.4 +19.3 +19.2 +19.1 +19.0 +18.9 +18.8 +18.7 +18.6 +18.5 +18.4 +18.3 +18.2 +18.1 +18.0 +17.9 +17.8 +17.7 +17.6 +17.5 +17.4 +17.3 +17.2 +17.1 +17.0 +16.9 +16.8 +16.7 +16.6 +16.5 +16.4 +16.3 +16.2 +16.1 56 +15.9 MW 100.000 +15.7 100.000 97.724 +15.6 97.724 95.499 +15.5 95.499 93.325 +15.4 93.325 91.201 +15.3 91.201 +15.2 89.125 89.125 +15.1 87.096 87.096 +15.0 85.114 85.114 +14.9 83.176 83.176 +14.8 81.283 81.283 +14.7 79.433 79.433 +14.6 77.625 77.625 +14.5 75.858 75.858 +14.4 74.131 74.131 +14.3 72.444 72.444 +14.2 70.795 70.795 +14.1 69.183 69.183 +14.0 67.608 67.608 +13.9 66.069 66.069 +13.8 64.565 64.565 +13.7 63.096 +13.6 63.096 61.660 +13.5 61.660 60.256 +13.4 60.256 58.884 +13.3 58.884 +13.2 57.544 57.544 +13.1 56.234 56.234 +13.0 54.954 54.954 +12.9 53.703 53.703 +12.8 52.481 52.481 +12.7 51.286 51.286 +12.6 50.119 50.119 +12.5 48.978 48.978 +12.4 47.863 47.863 +12.3 46.774 46.774 +12.2 45.709 45.709 +12.1 44.668 44.668 43.652 43.652 42.658 42.658 41.687 41.687 40.738 40.738 +15.8 MW mW dBm mW dBm mW dBm mW 39.811 +12.0 15.849 +8.0 6.310 +4.0 2.512 38.905 dBm +16.0 37.154 +16.0 +15.9 36.308 +15.9 +15.8 35.481 +15.8 +15.7 34.674 +15.7 +15.6 33.884 +15.6 33.113 +15.5 +15.5 32.359 +15.4 +15.4 31.623 +15.3 +15.3 30.903 +15.2 +15.2 30.200 +15.1 +15.1 29.512 +15.0 +15.0 28.840 +14.9 +14.9 28.184 +14.8 +14.8 27.542 +14.7 +14.7 26.915 +14.6 +14.6 26.303 +14.5 +14.5 25.704 +14.4 +14.4 25.119 +14.3 +14.3 24.547 +14.2 +14.2 23.988 +14.1 +14.1 23.442 +14.0 22.909 +14.0 +13.9 22.387 +13.9 +13.8 21.878 +13.8 +13.7 21.380 +13.7 20.893 +13.6 +13.6 20.417 +13.5 +13.5 19.953 +13.4 +13.4 19.498 +13.3 +13.3 19.055 +13.2 +13.2 18.621 +13.1 +13.1 18.197 +13.0 +13.0 17.783 +12.9 +12.9 17.378 +12.8 +12.8 16.982 +12.7 +12.7 16.596 +12.6 +12.6 16.218 +12.5 +12.5 +12.4 +12.4 +12.3 +12.3 +12.2 +12.2 +12.1 +12.1 38.019 dBm +11.9 MW 39.811 +11.7 39.811 38.905 +11.6 38.905 38.019 +11.5 38.019 37.154 +11.4 37.154 36.308 +11.3 36.308 +11.2 35.481 35.481 +11.1 34.674 34.674 +11.0 33.884 33.884 +10.9 33.113 33.113 +10.8 32.359 32.359 +10.7 31.623 31.623 +10.6 30.903 30.903 +10.5 30.200 30.200 +10.4 29.512 29.512 +10.3 28.840 28.840 +10.2 28.184 28.184 +10.1 27.542 27.542 +10.0 26.915 26.915 +9.9 26.303 26.303 +9.8 25.704 25.704 +9.7 25.119 +9.6 25.119 24.547 +9.5 24.547 23.988 +9.4 23.988 23.442 +9.3 23.442 +9.2 22.909 22.909 +9.1 22.387 22.387 +9.0 21.878 21.878 +8.9 21.380 21.380 +8.8 20.893 20.893 +8.7 20.417 20.417 +8.6 19.953 19.953 +8.5 19.498 19.498 +8.4 19.055 19.055 +8.3 18.621 18.621 +8.2 18.197 18.197 +8.1 17.783 17.783 17.378 17.378 16.982 16.982 16.596 16.596 16.218 16.218 +11.8 MW 15.488 dBm 15.136 dBm +12.0 14.791 +12.0 +11.9 14.454 +11.9 +11.8 14.125 +11.8 +11.7 13.804 +11.7 +11.6 13.490 +11.6 13.183 +11.5 +11.5 12.882 +11.4 +11.4 12.589 +11.3 +11.3 12.303 +11.2 +11.2 12.023 +11.1 +11.1 11.749 +11.0 +11.0 11.482 +10.9 +10.9 11.220 +10.8 +10.8 10.965 +10.7 +10.7 10.715 +10.6 +10.6 10.471 +10.5 +10.5 10.233 +10.4 +10.4 10.000 +10.3 +10.3 9.772 +10.2 +10.2 9.550 +10.1 +10.1 9.333 +10.0 9.120 +10.0 8.913+9.9 +9.9 8.710+9.8 +9.8 8.511 +9.7+9.7 8.318+9.6 +9.6 8.128 +9.5+9.5 7.943+9.4 +9.4 7.762+9.3 +9.3 7.586 +9.2+9.2 7.413 +9.1+9.1 7.244 +9.0+9.0 7.079 +8.9+8.9 6.918 +8.8+8.8 6.761 +8.7 +8.7 6.607 +8.6 +8.6 6.457 +8.5+8.5 +8.4+8.4 +8.3+8.3 +8.2+8.2 +8.1+8.1 +7.9 MW +7.8 MW 15.849 +7.7 15.849 15.488 +7.6 15.488 15.136 +7.5 15.136 14.791 +7.4 14.791 14.454 +7.3 14.454 +7.2 14.125 14.125 +7.1 13.804 13.804 +7.0 13.490 13.490 +6.9 13.183 13.183 +6.8 12.882 12.882 +6.7 12.589 12.589 +6.6 12.303 12.303 +6.5 12.023 12.023 +6.4 11.749 11.749 +6.3 11.482 11.482 +6.2 11.220 11.220 +6.1 10.965 10.965 +6.0 10.715 10.715 +5.9 10.471 10.471 +5.8 10.233 10.233 +5.7 10.000 +5.6 10.000 +5.59.772 9.772 +5.49.550 9.550 9.333 +5.3 9.333 +5.2 9.120 9.120 +5.1 8.913 8.913 +5.08.710 8.710 +4.98.511 8.511 +4.88.318 8.318 +4.7 8.128 8.128 +4.6 7.943 7.943 +4.5 7.762 7.762 +4.4 7.586 7.586 +4.3 7.413 7.413 +4.2 7.244 7.244 +4.1 7.079 7.079 6.918 6.918 6.761 6.761 6.607 6.607 6.457 6.457 6.166 dBm 6.026 dBm 5.888+8.0 +8.0 5.754+7.9 +7.9 5.623+7.8 +7.8 5.495+7.7 +7.7 5.370 +7.6+7.6 5.248+7.5 +7.5 5.129 +7.4+7.4 5.012+7.3 +7.3 4.898 +7.2+7.2 4.786+7.1 +7.1 4.677 +7.0+7.0 4.571 +6.9+6.9 4.467 +6.8 +6.8 4.365 +6.7 +6.7 4.266 +6.6 +6.6 4.169 +6.5 +6.5 4.074 +6.4 +6.4 3.981 +6.3 +6.3 3.890 +6.2 +6.2 3.802 +6.1 3.715+6.1 3.631+6.0 +6.0 3.548+5.9 +5.9 3.467+5.8 +5.8 3.388 +5.7+5.7 3.311+5.6 +5.6 3.236 +5.5+5.5 3.162+5.4 +5.4 3.090+5.3 +5.3 3.020 +5.2+5.2 2.951 +5.1+5.1 2.884 +5.0+5.0 2.818 +4.9+4.9 2.754 +4.8+4.8 2.692 +4.7 +4.7 2.630 +4.6 +4.6 2.570 +4.5+4.5 +4.4+4.4 +4.3+4.3 +4.2+4.2 +4.1+4.1 +3.9 MW +3.8 MW 6.310 +3.7 6.310 6.166 +3.6 6.166 6.026 +3.5 6.026 5.888 +3.4 5.888 5.754 +3.3 5.754 +3.2 5.623 5.623 +3.1 5.495 5.495 +3.0 5.370 5.370 +2.9 5.248 5.248 +2.8 5.129 5.129 +2.7 5.012 5.012 +2.6 4.898 4.898 +2.5 4.786 4.786 +2.4 4.677 4.677 +2.3 4.571 4.571 +2.2 4.467 4.467 +2.1 4.365 4.365 +2.0 4.266 4.266 +1.9 4.169 4.169 +1.8 4.074 4.074 +1.7 3.981 +1.6 3.981 +1.53.890 3.890 +1.43.802 3.802 3.715 +1.3 3.715 +1.2 3.631 3.631 +1.1 3.548 3.548 +1.03.467 3.467 +0.93.388 3.388 +0.83.311 3.311 +0.7 3.236 3.236 +0.6 3.162 3.162 +0.5 3.090 3.090 +0.4 3.020 3.020 +0.3 2.951 2.951 +0.2 2.884 2.884 +0.1 2.818 2.818 2.754 2.754 2.692 2.692 2.630 2.630 2.570 2.570 2.455 dBm 23.99 dBm +4.0 2.344 +4.0 +3.9 2.291 +3.9 +3.8 2.239 +3.8 +3.7 2.188 +3.7 2.138 +3.6+3.6 2.089 +3.5 +3.5 2.042 +3.4+3.4 1.995 +3.3+3.3 1.950 +3.2+3.2 1.905 +3.1+3.1 1.862 +3.0+3.0 1.820 +2.9+2.9 1.778 +2.8 +2.8 1.738 +2.7 +2.7 1.698 +2.6 +2.6 1.660 +2.5 +2.5 1.622 +2.4 +2.4 1.585 +2.3 +2.3 1.549 +2.2 +2.2 1.514 +2.1 +2.1 1.479 +2.0 1.445 +2.0 +1.9 1.413 +1.9 +1.8 1.380 +1.8 1.349 +1.7+1.7 1.318 +1.6 +1.6 1.288 +1.5+1.5 1.259+1.4 +1.4 1.230+1.3 +1.3 1.202 +1.2+1.2 1.175 +1.1+1.1 1.148 +1.0+1.0 1.122 +0.9+0.9 1.096 +0.8+0.8 1.072 +0.7 +0.7 1.047 +0.6 +0.6 1.023 +0.5+0.5 +0.4+0.4 +0.3+0.3 +0.2+0.2 +0.1+0.1 56 Subject to change without Subject to change without notice notice 61 MW M 2. 2.512 2. 2.455 23 23.99 2. 2.344 2. 2.291 2. 2.239 2. 2.188 2. 2.138 2. 2.089 2. 2.042 1. 1.995 1. 1.950 1. 1.905 1. 1.862 1. 1.820 1. 1.778 1. 1.738 1. 1.698 1. 1.660 1. 1.622 1. 1.585 1. 1.549 1. 1.514 1. 1.479 1. 1.445 1. 1.413 1. 1.380 1. 1.349 1. 1.318 1. 1.288 1. 1.259 1. 1.230 1. 1.202 1. 1.175 1. 1.148 1. 1.122 1. 1.096 1. 1.072 1. 1.047 1. 1.023 Tables Tables Conversion dBm Ratio Conversion dBm Ratio Conversion Ratio dBm Conversion Ratio dBm Conversion dBm Conversion dBm PdBm US ––— ––– = 10 20 UE US PdBm = 20 log –––— UE dBm 0.0 0.1 0.2 0.3 W 2 5 9 4 1 9 8 8 9 2 5 0 5 2 0 8 8 8 0 2 5 9 4 9 5 3 0 9 8 8 9 0 2 5 8 2 6 2 7 3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 62 dBm dBm Ratio0.0 0.0 1.0000.1 0.1 1.0120.2 0.2 1.0230.3 0.3 1.0350.4 0.4 1.0470.5 0.5 1.0590.6 0.6 1.072 0.7 0.7 1.084 0.8 0.8 1.096 0.9 0.9 1.109 1.0 1.0 1.122 1.1 1.135 1.1 1.2 1.148 1.2 1.3 1.161 1.3 1.4 1.175 1.4 1.5 1.189 1.5 1.6 1.202 1.6 1.216 1.7 1.7 1.230 1.8 1.8 1.245 1.9 1.9 1.259 2.0 2.0 1.274 2.1 2.1 1.288 2.2 2.2 1.303 2.3 2.3 1.318 2.4 2.4 1.334 2.5 2.5 1.349 2.6 2.6 1.365 2.7 2.7 1.380 2.8 2.8 1.396 2.9 2.9 1.413 3.0 3.0 1.429 3.1 3.1 1.445 3.2 1.462 3.3 1.479 3.4 1.496 1.514 3.5 1.531 3.6 1.549 3.7 1.5673.8 1.5853.9 1.6034.0 1.6224.1 1.6414.2 1.6604.3 1.6794.4 4.5 Ratio Ratio 1.000 dBm 1.000 4.61.012 1.012 4.71.023 1.023 4.81.035 1.035 4.91.047 1.047 5.01.059 1.059 5.11.072 1.072 5.2 1.084 1.084 5.3 1.096 1.096 5.4 1.109 1.109 5.5 1.122 1.122 5.6 1.135 5.71.135 1.148 5.81.148 1.161 5.91.161 1.175 6.01.175 1.189 6.11.189 1.202 6.21.202 6.31.216 1.216 6.41.230 1.230 6.51.245 1.245 6.61.259 1.259 6.71.274 1.274 6.81.288 1.288 6.91.303 1.303 7.01.318 1.318 7.11.334 1.334 7.21.349 1.349 7.3 1.365 1.365 7.4 1.380 1.380 7.5 1.396 1.396 7.6 1.413 1.413 7.7 1.429 1.429 7.8 1.445 7.9 1.462 8.0 1.479 8.1 8.21.496 8.31.514 8.41.531 8.51.549 8.61.567 8.71.585 8.81.603 8.91.622 9.01.641 9.11.660 1.679 Ratio Ratio dBm dBm Ratio4.6 4.6 1.6984.7 4.7 1.7184.8 4.8 1.7384.9 4.9 1.7585.0 5.0 1.7785.1 5.1 1.7995.2 5.2 1.820 5.3 5.3 1.841 5.4 5.4 1.862 5.5 5.5 1.884 5.6 5.6 1.905 5.7 1.9285.7 5.8 1.9505.8 5.9 1.9725.9 6.0 1.9956.0 6.1 2.0186.1 6.2 2.0426.2 2.0656.3 6.3 2.0896.4 6.4 2.1136.5 6.5 2.1386.6 6.6 2.1636.7 6.7 2.1886.8 6.8 2.2136.9 6.9 2.2397.0 7.0 2.2657.1 7.1 2.2917.2 7.2 2.317 7.3 7.3 2.344 7.4 7.4 2.371 7.5 7.5 2.399 7.6 7.6 2.427 7.7 7.7 2.455 7.8 2.483 7.9 2.512 8.0 2.541 2.5708.1 2.6008.2 2.630 8.3 2.6618.4 2.6928.5 2.7238.6 2.7548.7 2.7868.8 2.8188.9 2.8519.0 9.1 Ratio Ratio 1.698 dBm 1.698 9.21.718 1.718 9.31.738 1.738 9.41.758 1.758 9.51.778 1.778 9.61.799 1.799 9.71.820 1.820 9.8 1.841 1.841 9.9 1.862 1.862 10.0 1.884 1.884 10.1 1.905 1.905 10.2 1.928 10.31.928 1.950 10.41.950 1.972 10.51.972 1.995 10.61.995 2.018 10.72.018 2.042 10.82.042 10.92.065 2.065 11.02.089 2.089 11.12.113 2.113 11.22.138 2.138 11.32.163 2.163 11.42.188 2.188 11.52.213 2.213 11.62.239 2.239 11.72.265 2.265 11.82.291 2.291 11.9 2.317 2.317 12.0 2.344 2.344 12.1 2.371 2.371 12.2 2.399 2.399 12.3 2.427 2.427 12.4 2.455 12.5 2.483 12.6 2.512 12.7 12.82.541 12.92.570 13.02.600 2.630 13.1 13.22.661 13.32.692 13.42.723 13.52.754 13.62.786 13.72.818 2.851 dBm dBm Ratio9.2 9.2 2.8849.3 9.3 2.9179.4 9.4 2.9519.5 9.5 2.9859.6 9.6 3.0209.7 9.7 3.0559.8 9.8 3.090 9.9 9.9 3.126 10.0 10.0 3.162 10.1 10.1 3.199 10.2 10.2 3.236 10.3 3.27310.3 10.4 3.31110.4 10.5 3.35010.5 10.6 3.38810.6 10.7 3.42810.7 10.8 3.46710.8 3.50810.9 10.9 3.54811.0 11.0 3.58911.1 11.1 3.63111.2 11.2 3.67311.3 11.3 3.71511.4 11.4 3.75811.5 11.5 3.80211.6 11.6 3.84611.7 11.7 3.89011.8 11.8 3.936 11.9 11.9 3.981 12.0 12.0 4.027 12.1 12.1 4.074 12.2 12.2 4.121 12.3 12.3 4.169 12.4 4.217 12.5 4.266 12.6 4.315 4.36512.7 4.41612.8 4.46712.9 13.0 4.519 13.1 4.571 4.62413.2 4.67713.3 4.73213.4 4.78613.5 4.84213.6 13.7 Ratio Ratio 2.884 dBm 2.884 13.8 2.917 2.917 13.9 2.951 2.951 14.0 2.985 2.985 14.1 3.020 3.020 14.2 3.055 3.055 14.3 3.090 3.090 14.4 3.126 3.126 14.5 3.162 3.162 14.6 3.199 3.199 14.7 3.236 3.236 14.8 3.273 3.273 14.9 3.311 3.311 15.0 3.350 3.350 15.1 3.388 3.388 15.2 3.428 3.428 15.3 3.467 3.467 15.4 3.508 15.5 3.508 3.548 15.6 3.548 3.589 15.7 3.589 3.631 15.8 3.631 15.9 3.673 3.673 16.0 3.715 3.715 16.1 3.758 3.758 16.23.802 3.802 16.33.846 3.846 16.43.890 3.890 16.5 3.936 3.936 16.6 3.981 3.981 16.7 4.027 4.027 16.8 4.074 4.074 16.9 4.121 4.121 17.0 4.169 17.1 4.217 17.2 4.266 17.3 4.315 17.4 4.365 17.5 17.64.416 4.467 17.7 4.519 17.8 4.571 17.9 18.0 4.624 18.1 4.677 18.2 4.732 18.3 4.786 4.842 dBm dBm 13.8 Ratio 13.8 4.898 13.9 13.9 4.955 14.0 14.0 5.012 14.1 14.1 5.070 14.2 14.2 5.129 14.3 14.3 5.188 14.4 14.4 5.248 14.5 14.5 5.309 14.6 14.6 5.370 14.7 14.7 5.433 14.8 14.8 5.495 14.9 14.9 5.559 15.0 15.0 5.623 15.1 15.1 5.689 15.2 15.2 5.754 15.3 15.3 5.821 15.4 15.4 5.888 15.5 5.957 15.5 15.6 6.026 15.6 15.7 6.095 15.7 15.8 6.166 15.8 6.237 15.9 15.9 6.310 16.0 16.0 6.383 16.1 16.1 6.457 16.2 16.2 6.53116.3 16.3 6.60716.4 16.4 6.683 16.5 16.5 6.761 16.6 16.6 6.839 16.7 16.7 6.918 16.8 16.8 6.998 16.9 16.9 7.079 17.0 7.161 17.1 7.244 17.2 7.328 17.3 7.413 17.4 7.499 7.58617.5 17.6 7.674 17.7 7.762 17.8 7.852 7.943 17.9 8.035 18.0 8.128 18.1 8.222 18.2 18.3 Ratio Ratio 4.898 dBm 4.898 18.4 4.955 4.955 18.5 5.012 5.012 18.6 5.070 5.070 18.7 5.129 5.129 18.8 5.188 5.188 18.9 5.248 5.248 19.0 5.309 5.309 19.1 5.370 5.370 19.2 5.433 5.433 19.3 5.495 5.495 19.4 5.559 5.559 19.5 5.623 5.623 19.6 5.689 5.689 19.7 5.754 5.754 19.8 5.821 5.821 19.9 5.888 205.888 5.957 20.1 5.957 6.026 20.2 6.026 6.095 20.3 6.095 6.166 20.4 6.166 20.5 6.237 6.237 20.6 6.310 6.310 20.7 6.383 6.383 20.8 6.457 6.457 20.9 6.531 6.531 216.607 6.607 21.1 6.683 6.683 21.2 6.761 6.761 21.3 6.839 6.839 21.4 6.918 6.918 21.5 6.998 6.998 21.6 7.079 21.7 7.161 21.8 7.244 21.9 227.328 7.413 22.1 7.499 22.2 7.586 22.3 7.674 22.4 7.762 22.5 22.6 7.852 22.7 7.943 22.8 8.035 22.9 8.128 8.222 dBm dBm 18.4 Ratio 18.4 8.318 18.5 18.5 8.414 18.6 18.6 8.511 18.7 18.7 8.610 18.8 18.8 8.710 18.9 18.9 8.810 19.0 19.0 8.913 19.1 19.1 9.016 19.2 19.2 9.120 19.3 19.3 9.226 19.4 19.4 9.333 19.5 19.5 9.441 19.6 19.6 9.550 19.7 19.7 9.661 19.8 19.8 9.772 19.9 19.9 9.886 20 10.00020 20.1 10.116 20.1 20.2 10.233 20.2 20.3 10.351 20.3 20.4 10.471 20.4 10.593 20.5 20.5 10.715 20.6 20.6 10.839 20.7 20.7 10.965 20.8 20.8 11.092 20.9 20.9 11.22021 21 11.350 21.1 21.1 11.482 21.2 21.2 11.614 21.3 21.3 11.749 21.4 21.4 11.885 21.5 21.5 12.023 21.6 12.162 21.7 12.303 21.8 12.445 21.9 12.589 12.73522 22.1 12.882 22.2 13.032 22.3 13.183 22.4 13.335 13.490 22.5 13.646 22.6 13.804 22.7 13.964 22.8 22.9 Ratio Ratio 8.318 8.318 8.414 8.414 8.511 8.511 8.610 8.610 8.710 8.710 8.810 8.810 8.913 8.913 9.016 9.016 9.120 9.120 9.226 9.226 9.333 9.333 9.441 9.441 9.550 9.550 9.661 9.661 9.772 9.772 9.886 9.886 10.00 10.00 10.11 10.11 10.23 10.23 10.35 10.35 10.47 10.47 10.59 10.59 10.71 10.71 10.83 10.83 10.96 10.96 11.09 11.09 11.22 11.22 11.35 11.35 11.48 11.48 11.61 11.61 11.74 11.74 11.88 11.88 12.02 12.16 12.30 12.44 12.58 12.73 12.88 13.03 13.18 13.33 13.49 13.64 13.80 13.96 Subject Subjecttotochange changewithout without notice notice Tables Tables Conversion dBµV Volt Conversion dBμV Volt Conversion Volt dBµV dBμV Conversion Volt Conversion dBμV Conversion dBµV U PdBµm = 20 log –––— U0 U = U0 · 10 Volt Volt PdBµV ––— 20 with: U0 = 1µV dBµV µVolt dBµV µVolt dBµV µVolt dBµV µVolt dBµV 0 1.00 40 100 60 1.00 100 100 120 µVolt 1.00 1 1.12 41 112 61 1.12 101 112 121 1.12 2 1.26 42 126 62 1.26 102 126 122 1.26 3 1.41 dBNV 43NVolt 141 dBNV 63NVolt 1.41 dBNV 103 mVolt 141 dBNV 123 mVolt 1.41 dBNV 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 dBNV 00 1.78 11 2.00 22 2.24 33 2.51 44 2.82 5 3.16 5 6 3.55 6 7 3.98 7 8 4.47 8 9 5.01 9 10 5.62 10 11 6.31 11 12 7.08 12 13 7.94 13 8.91 14 10.0 15 11.2 16 12.6 17 14.1 18 15.8 19 17.8 20 20.0 21 22.4 22 25.1 23 28.2 24 31.6 25 35.5 39.8 26 44.7 27 50.1 28 56.2 29 63.1 30 70.8 31 79.4 32 89.1 33 100 34 35 36 37 38 39 40 1.58 NVolt 1.00 45 1.12 1.12 46 1.26 1.26 47 1.41 1.41 48 1.58 1.58 49 1.78 50 1.78 2.00 51 2.00 2.24 52 2.24 2.51 53 2.51 2.82 54 2.82 3.16 55 3.16 3.55 56 3.55 3.98 57 3.98 4.47 58 4.47 59 5.01 5.62 6.31 7.08 7.94 8.91 10.0 11.2 12.6 14.1 15.8 17.8 20.0 22.4 25.1 28.2 31.6 35.5 39.8 44.7 50.1 56.2 63.1 70.8 79.4 89.1 100 44 1.00 dBNV 40 40 178 41 41 200 42 42 224 43 43 251 44 44 282 45 316 45 46 355 46 47 398 47 48 447 48 49 501 49 50 562 50 51 631 51 52 708 52 53 794 53 891 54 55 56 57 58 59 158 58 Subject Subjectto tochange changewithout withoutnotice notice NVolt 100 100 65 112 112 66 126 126 67 141 141 68 158 158 69 178 70 178 200 71 200 224 72 224 251 73 251 282 74 282 316 75 316 355 76 355 398 77 398 447 78 447 79 501 80 562 81 631 82 708 83 794 84 891 64 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 dBNV 60 1.78 61 61 2.00 62 62 2.24 63 63 2.51 64 64 2.82 65 3.16 65 66 3.55 66 67 3.98 67 68 4.47 68 69 5.01 69 70 5.62 70 71 6.31 71 72 7.08 72 73 7.94 73 8.91 74 10.0 75 11.2 76 12.6 77 14.1 78 15.8 79 17.8 80 20.0 81 22.4 82 25.1 83 28.2 84 31.6 85 35.5 39.8 86 44.7 87 50.1 88 56.2 89 63.1 90 70.8 91 79.4 92 89.1 93 94 95 96 97 98 99 1.58 60 mVolt 1.00 105 1.12 1.12 106 1.26 1.26 107 1.41 1.41 108 1.58 1.58 109 1.78 1101.78 2.00 1112.00 2.24 1122.24 2.51 1132.51 2.82 1142.82 3.16 1153.16 3.55 1163.55 3.98 1173.98 4.47 1184.47 1195.01 5.62 6.31 7.08 7.94 8.91 10.0 11.2 12.6 14.1 15.8 17.8 20.0 22.4 25.1 28.2 31.6 35.5 39.8 44.7 50.1 56.2 63.1 70.8 79.4 89.1 1041.00 dBNV 100 178 101 101 200 102 102 224 103 103 251 104 104 282 105 316105 106 355106 107 398107 108 447108 109 501109 110 562110 111 631111 112 708112 113 794113 891114 115 116 117 118 119 158100 mVolt 100 125 112 112 126 126 126 127 141 141 128 158 158 129 178 178 200 200 224 224 251 251 282 282 316 316 355 355 398 398 447 447 501 562 631 708 794 891 124100 dBNV 120 1.78 121 121 2.00 122 122 2.24 123 123 2.51 124 124 2.82 125 125 126 126 127 127 128 128 129 129 1.58120 63 V V 1 1. 1 1. 1 1. 1 1. 1 1. 1 1. 2 2. 2 2. 2 2. 2 2. Ihr Spezialist für Mess- und Prüfgeräte value-instruments.com www.hameg.com HAMEG Instruments GmbH Industriestr. 6 | 63533 Mainhausen | Germany | Tel +49 (0) 6182 8000 R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG HAMEG Instruments® is a registered trademark of HAMEG Instruments GmbH; Trade names are trademarks of the owners 04 / 2015 | © HAMEG Instruments GmbH | 45-8135-0011 Printed in Germany | Subject to change without notice Distributed by: dataTec ▪ Ferdinand-Lassalle-Str. 52 ▪ 72770 Reutlingen ▪ Tel. 07121 / 51 50 50 ▪ Fax 07121 / 51 50 10 ▪ [email protected] ▪ www.datatec.de