Download Operating instructions S4E450GA0901

Operating instructions
S4E450-GA09-01
Insulation class
Humidity class
Mounting position
3.2 Nominal data
Motor
M4E094-HA
Phase
Nominal voltage / VAC
Frequency / Hz
1~
230
50
1~
230
60
Type of data definition
Valid for approval /
standard
Speed / min-1
Power input / W
Current draw / A
Motor capacitor / µF
Capacitor voltage / VDB
Max. back pressure / Pa
Min. ambient temperature
/ °C
Max. ambient
temperature
/ °C
Starting current / A
Maximum safe operating
speed / min-1
ml
CE
ml
CE
1350
480
2.1
10
400
125
-40
1490
665
2.9
10
400
115
-40
65
50
6.3
1800
@ 75 °C
5.6
1800
@ 75 °C
Condensate discharge
holes
Operation mode
Motor bearing
Touch current acc.
IEC 60990 (measuring
network Fig. 4, TN
system)
Electrical leads
Motor protection
Protection class
Product conforming
to standard
Approval
Strength class for
mounting screws
A
Static
No
1.00
31.6
40
0.47
4495
120
1355
8.8
You can obtain additional mounting data from the product drawing if
necessary.
Specific ratio = 1 + pfs / 100 000 Pa
Actual
Translation of the original operating instructions
CCC; EAC
; Secure the mounting screws against accidentally coming loose (e.g.
by using self-locking screws).
3.3 Data according to ErP directive
Overall efficiency ηes / %
Efficiency grade N
Power input Pe / kW
Air flow qv / m³/h
Pressure increase total psf / Pa
Speed n / min-1
Via terminal box, integrated capacitor
connected via terminal box
Thermal overload protector (TOP)
brought out
I (if protective earth is connected by
customer)
EN 60034-1 (2004)
3.5 Mounting data
Subject to alterations
*
S1
Ball bearing
<= 3.5 mA
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
ml = Max. load · me = Max. efficiency · fa = Running at free air
cs = Customer specs · cu = Customer unit
Installation category
Efficiency category
Variable speed drive
Specific ratio*
"F"
F3-1
Shaft horizontal or rotor on bottom; rotor
on top on request
Rotor-side
Request
2013
27.6
36
Request
2015
31.6
40
3.6 Transport and storage conditions
; Use the device in accordance with its protection type.
Max. permissible
ambient motor temp.
(transp./ storage)
Min. permissible
ambient motor temp.
(transp./storage)
+ 80 °C
- 40 °C
Data definition with optimum efficiency.
The ErP data is determined using a motor-impeller combination in a standardised
measurement configuration.
3.4 Technical features
Mass
Size
Surface of rotor
Material of terminal box
Material of blades
Material of guard grille
Number of blades
Direction of air flow
Direction of rotation
Type of protection
10.5 kg
450 mm
Coated in black
PC/ABS plastic, black
Sheet steel, coated in black
Steel, phosphated and coated in black
plastic
5
"V"
Counter-clockwise, seen on rotor
IP 54
Item no. 11124-5-9970 · Revision 82623 · Release 2014-05-08 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com