Download SERVICE MANUAL

SERVICE MANUAL
LCD TV
Model No. LEC32B33200
ZMSD318
Chassis
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair
the product or products dealt with in this service information by anyone else could result in serious injury or death.
©2009 Qingdao Haier Electronics Co., Ltd.
All rights reserved. Unauthorized copying and distribution is a violation of law.
Haier Group
Chapter 1: General Information
1-1. Table of Contents
1. General Information...........................................................................1
1-1. Table of Contents
1-2. General Guidelines
1-3. Important Notice
1-4. How to Read this Service Manual
1
3
3
6
.................................................................................... 7
3. Location of Controls and Components........................................... 8
3-1. Board Location
8
3-2. Main Board & AV Board
8
3-3. Power Board
11
3-4. LCD Panel
12
4. Disassemble and Assemble.......................................................... 14
4-1 Remove the Pedestal
14
4-2 Remove the Back Cover
14
4-3 Remove the Terminal Bracket
15
4-4 Remove the Power Module
15
4-5 Remove the Main Board
4-6 Remove the Speaker
4-7 Remove the Remote Control Board
15
16
16
5. Installation Instructions..…....………………...........…………......... 16
5-1 External Equipment Connections
16
5-2 HDMI Connections
20
6. Operation Instructions....…....………………...........…………......... 24
6-1 Front Panel Controls
24
6-2 Back Panel Controls
24
6-3 Universal Remote Control
25
7. Electrical Parts…....………………...........…………......................... 26
7-1. Circuit Diagram
26
7-2. Wiring Connection Diagram
35
- 01 -
8. TV Operation........…………............................................................. 36
8.1 How to enter into the factory model
8.2 How to update software
41
42
9. Trouble-shooting………….............................................................. 43
9-1. Simple Check
43
9-2. Main Board Failure Check
44
9-3. Panel Failure
53
10. DVD OPERATION
………….............................................................. 56
11. DVD TROUBLE SHOOTING
………….............................................................. 60
- 02 -
1-2. General Guidelines
When servicing, observe the original lead dress. If a short circuit is found, replace all parts
which have been overheated or damaged by the short circuit.
After servicing, see to it that all the protective devices such as insulation barriers, insulation
papers shields are properly installed.
After servicing, make the following leakage current checks to prevent the customer from
being exposed to shock hazards.
1) Leakage Current Cold Check
2) Leakage Current Hot Check
3) Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive
1-3. Important Notice
1-3-1. Follow the regulations and warnings
Most important thing is to list up the potential hazard or risk for the service personnel to
open the units and disassemble the units. For example, we need to describe properly
how to avoid the possibility to get electrical shock from the live power supply or charged
electrical parts (even the power is off).
This symbol indicates that high voltage is present inside.It is dangerous to
make any king of contact with any inside part of this product.
This symbol indicates that there are important operating and maintenance
instructions in the literture accompanying the appliance.
1-3-2. Be careful to the electrical shock
to rain or excessive moisture. This TV must not be exposed to dripping or splashing water,
1-3-3. Electro static discharge (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such
components commonly are called Electrostatically Sensitive (ES) Devices. The following
techniques should be used to help reduce the incidence of component damage caused by
electros static discharge (ESD).
1-3-4. About lead free solder (PbF)
This product is manufactured using lead-free solder as a part of a movement within the
consumer products industry at large to be environmentally responsible. Lead-free solder
must be used in the servicing and repairing of this product.
!"#"$%
'
*
Special parts which have purposes of fire retardant (resistors), high-quality sound
(capacitors), low noise (resistors), etc. are used.
When replacing any of components, be sure to use only manufacture's specified parts
shown in the parts list.
Safety Component
/:
;
;
- 03 -
1-3-6 Safety Check after Repairment
:
in the original positions, or whether there are the positions which are deteriorated around
the serviced places serviced or not. Check the insulation between the antenna terminal or
external metal and the AC cord plug blades. And be sure the safety of that.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power source before;
a. Removing or reinstalling any component, circuit board module or any other receiver
assembly.
b. Disconnecting or reconnecting any receiver electrical plug or other electrical
connection.
c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic
capacitors may result in an explosion hazard.
2. Test high voltage only by measuring it with an appropriate high voltage meter or other
voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage
probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its assemblies.
4. Unless specified otherwise in this service manual, clean electrical contacts only by
applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or
comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume)
isopropyl alcohol (90%-99% strength).
CAUTION:X
%
Capacitors may result in an explosion hazard.
5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this
service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless
all solid-state device heat sinks are correctly installed.
7. Always connect the test receiver ground lead to the receiver chassis ground before
connecting the test receiver positive lead.
Always remove the test receiver ground lead last. Capacitors may result in an explosion
hazard.
@%
;
CAUTION: J
;
eiver.
9. Remove the antenna terminal on TV and turn on the TV.
10. Insulation resistance between the cord plug terminals and the eternal exposure metal
should be more than Mohm by using the 500V insulation resistance meter.
11. If the insulation resistance is less than M ohm, the inspection repair should be required.
If you have not the 500V insulation resistance meter, use a Tester. External exposure
metal: Antenna terminal Headphone jack
- 04 -
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be damaged easily by static electricity.
Such components commonly are called Electrostatically Sensitive (ES) Devices.
Examples of typical ES devices are integrated circuits and some field-effect transistors
and semiconductor "chip" components. The following techniques should be used to help
reduce the ncidence of component damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or semiconductorequipped assembly, drain off any electrostatic charge on your body by touching a known
earth ground. Alternatively, obtain and wear a commercially available discharging wrist
strap device, which should be removed to prevent potential shock reasons prior to applying
power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly
on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static type solder removal device. Some solder removal devices not
Z
"
Z
[\
$J
"
to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately
before you are ready to install it.
(Most replacement ES devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement
ES device, touch the protective material to the chassis or circuit assembly into which the
device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other
safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices.
(Otherwise harmless motion such as the brushing together of your clothes fabric or the
;
X
;
an ES device.)
1-3-7. Ordering Spare Parts
Please include the following informations when you order parts. (Particularly the Version
letter)
1. Model number, Serial number and Software Version
The model number and Serial number can be found on the back of each product and the
Software Version can be found at the Spare Parts List.
2. Spare Part No. and Description
]
\^
_
- 05 -
1-3-8. Photo used in this manual
The illustration and photos used in this Manual may not base on the final design of
products, which may differ from your products in some way.
1-4. How to Read this Service Manual
Using Icons:
`
each icon is described in the table below:
Note:
A “note” provides information that is not indispensable, but may nevertheless be valuable
to the reader, such as tips and tricks.
Caution:
A “caution” is used when there is danger that the reader, through incorrect manipulation,
may damage equipment, loose data, get an unexpected result or has to restart(part of) a
procedure.
Warning:
A “warning” is used when there is danger of personal injury.
Reference:
A “reference” guides the reader to other places in this binder or in this manual, where he/
- 06 -
Service Manual
Model No.:
2. Speci
cations
Model
LEC32B33200
Screen Size
31.5
Aspect Ratio
16:9
Resolution
1366x768
Response Time (ms)
inch
6.5 (GRAY TO
GRAY)
+88/-88(H), +88/-88
(V) Typ.
Color Display
16.7M
Cable :1-135/ Air:
No. of Preset Channels
2-69(ATV&DTV)
OSD Language
English
Angel of View
Color System
NTSC
Audio System
M
Audio Output Power
(Built-in) (W)
8W×2
Audio Output Power
(outer) (W)
No
Total Power Input (W)
120W
Voltage Range (V)
AC100V-240V
Power Frequency (Hz) 50~60Hz
Net Weight (KG)
9.5
Gross Weight (KG)
12.2
Net Dimension (MM)
Packaged Dimension
(MM)
793*113*511m
m
980*205*626m
m
- 07 -
3. Location of Controls and Components
3-1 Board Location
A Board
B Board
No.
Description
LEC32B33200
A Board
Main Board
B Board
Power Board
DH00DLM0000M
514C3207M06
3-2 Main Board
- 08 -
3-2-1 Function Description:
Main Board
Process signal which incept from exterior equipment then translate into signal that panel
can display.
3-2-2 Connector defnition
Main board connector
Power connectors (J15ˈJ16)
-
3LQQXPEHU
6LJQDOQDPH
9
%/212))
%/$'-867
high voltage
*1'
3LQQXPEHU
-
6LJQDOQDPH
*1'
*1'
9
9
32:(5212))
967%
9
9
*1'
*1'
*1'
9
9
Notes:
J16-Pin 2: Backlight on/off:
The system c an t urn o n or turn o ff t he backlight of T FT L CD P anel t hrough t he power
supply unit path.
J15
CN115-Pin
5: System power on / standby
System board will use this pin to control system power.
J16-Pin 3: Control the luminance of backlight
The system can generate the P WM s ignal to control the strength of T FT LCD Panel’s
backlight through this connector
- 09 -
remote connector (J6)
3LQQXPEHU
6LJQDOQDPH
/('B5
/('B*
'HVFULSWLRQ
/$035('
/$03*5((1
,5
*1'
9
5(027(&21752/
*1'
32:(5)255(027(
Keypad and connector (J7)
3LQQXPEHU
6LJQDOQDPH
.(<
.(<
*1'
'HVFULSWLRQ
Speaker connector J11
Pin number
1
2
3
4
Signal nameD
RSPK+
RSPKLSPKLSPK+
escription
RSPK+
RSPKLSPKLSPK+
- 10 -
3-3. Power Board
3-3-1 Function Description:
Supply power for Main board, Panel.
&1
3LQQXPEHU
6LJQDOQDPH
3LQQXPEHU
&1
6LJQDOQDPH
9
9
*1'
*1'
*1'
9
9
967%
32:(5212))
- 11 -
3-4. LCD Panel
MTC315LED-D01H(PANDA:LM315TA-T01)
- 12 -
3-4-1 Function Description: Display the signal.
3LQ1R
6\PERO
5HPDUN
9&&
93RZHU6XSSO\
9&&
93RZHU6XSSO\
9&&
93RZHU6XSSO\
9&&
93RZHU6XSSO\
*1'
*URXQG
*1'
*URXQG
*1'
*URXQG
*1'
*URXQG
6(//9'6
6HOHFW/9'6GDWDRUGHU>1RWH@
5HVHUYHG
1RW$YDLODEOH
*1'
*URXQG
5,1
1HJDWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
5,1
3RVLWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
*1'
*URXQG
5,1
1HJDWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
5,1
3RVLWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
*1'
*URXQG
5,1
1HJDWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
5,1
3RVLWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
*1'
*URXQG
&/.,1
&ORFN6LJQDO
/9'6
&/.,1
&ORFN6LJQDO
/9'6
*1'
*URXQG
5,1
1HJDWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
5,1
3RVLWLYH/9'6GLIIHUHQWLDOGDWDLQSXW
/9'6
*1'
*URXQG
5HVHUYHG
1RW$YDLODEOH
5HVHUYHG
1RW$YDLODEOH *1'
*URXQG
*1'
*URXQG
- 13 -
'HIDXOWSXOOGRZQ
/*1'>1RWH@
4. Disassemble and assemble
4-1 Remove the Pedestal
_;
faces upward
 €
4-2Remove the Back Cover

;€
unit.
4-3. Remove the adhesive tape
Remove the adhesive tape indicated on the
- 14 -
4-4 Remove the power module
 ;€
4-5 Remove the Main board
 ;€
J
J6 J7 J9 J15 J16 J5 J3 J11 J17


4-6 Remove the speaker
Take out the speaker
- 15 -
4-7 Remove the remote control
take out the remote control board
5. Installation Instructions
5-1 External Equipment Connections
Accessories
Remote Control
User GUIDE
- 16 -
Battery
ANTENNA
Note:
Aerial connections: IEC (female).
Input impendance:75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are set to
Power off.
1.Connect VGA and audio cable.
2.Connect the power cord.
3.Power on the TV, switch to PC mode.
4.Power on the PC.
This sequence is very important.
HDMI1
HDMI2
USB
VGA
HEADPHONE PC AUDIO COAXIAL
- 17 -
RF
VIDEO
L
R
Y
Pb
Pr
AC-INPUT
100-240V~50/60Hz
COMPOSITE
COMPONENT
PC
PRESET MODE
RESOLUTION
V.Freq.(Hz)
H.Freq.(KHz)
1
720*400
70
31.47
2
640*480
60
31.47
3
640*480
75
37.50
4
800*600
60
37.88
5
800*600
75
46.88
6
1024*768
60
48.36
7
1024*768
70
56.48
8
1024*768
75
60.02
9
1280*1024
60
63.98
10
1280*1024
75
80.00
11
1366*768
60
80.00
- 18 -
AV EQUIPMENT
You can use the input terminals on TV set rear as follows.
HDMI1
USB
HDMI2
VGA
HEADPHONE PC AUDIO COAXIAL
RF
HDMI
VIDEO EQUIPMENT with YPbPr
G
B
R
W
R
Y Yellow (video)
W White(audio L)
R Red(audio R or Pr)
B Blue(Pb)
G Green(Y)
VIDEO
L
G
R
W
R
Y
B
R
Pb
Pr
AC-INPUT
100-240V~50/60Hz
COMPONENT
COMPOSITE
W
R
VIDEO EQUIPMENT
W
R
TO VIDEO
OUTPUTS
TO AUDIO OUTPUTS
The television's inputs can be connected to the following types of equipment: VCR, multi disc player,
DVD, camcorder, video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i.
- 19 -
5-2 HDMI Connections
When the source device(DVD player or Set Top Box) supports HDM
How To Connect
1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied
with this product).
2. No separated audio connection is necessary.
How To Use
If the source device supports Auto HDMI function, the output resolution of the source
device will be automatically
set to 1280x720p.
If the source device does not support Auto HDMI, you need to set the output resolution
appropriately.
To get the best picture quality, adjust the output resolution of the source device to
1280x720p.
Select HDMI input source in input source option of Select Main source menu.
When the source device(DVD player or Set Top Box) supports DVI
How To Connect
1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not
supplied with this product).
2. A separated audio connection is necessary.
3. If the source device has an analog audio output connector, connect the source device
audio output to DVI Audio In port located on the PC port.
How To Use
If the source device supports Auto DVI function, the output resolution of the source device
will be automatically
set to 1280x720p.
If the source device does not support Auto DVI, you need to set the output resolution
appropriately.
To get the best picture quality, adjust the output resolution of the source device to
1280x720p.
Press the INPUT button to select HDMI input source in input source option of Select Main
source menu.
Installation
- 20 -
Cable sample
HDMI Cable
(not supplied with the product)
HDMI to DVI Cable
( not supplied with the product)
Analog Audio Cable
(Stereo to RCA type)
(not supplied with the product)
Connecting Headphones
You can connect a set of headphones to your set if you wish to watch a
TV programmer without disturbing the other people in the room.
- 21 -
Power source
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC.
Insert the AC cord plug into a standard polarized AC outlet.
NOTES:
‚„
…:
Use the attached power cord only.
‚`
†…:
"†…:
`
‡
;
electrician replace the obsolete outlet.
‚`;
simply unplug the unit from the AC outlet and plug it back in. The unit should return to
normal operation.
- 22 -
6. Operation Instructions
6-1 Front panel controls
Side panel
Front panel
3
SOURCE
1
MENU
2
CH+
3
1
CH-
2
VOL+
4
VOLSTANDBY
30
RETURN
DISPLAY
CC/
REPEAT
CH LIST/
AUDIO
SUBTITLE
MTS/
MENU
GOTO
EPG/
5
30
FAV/
SETUP
ASPECT
TV
DISPLAY
1. SOURCE: Display the input source menu.
2. MENU: Display main MENU.
3. CH+/CH-: In TV mode, press "CH+" or "CH-" to
change the channel up and down. In MENU mode, press
"CH+" or "CH-" to select items in standby mode, press
"CH+" or "CH-" to turn on the TV.
4. VOL+/VOL-: Adjust sound level. In MENU mode,
press "VOL+ " or "VOL- " to adjust the item that you
selected.
5. STANDBY: Press this button to turn the unit ON
from STANDBY mode. Press it again to turn the set
back to STANDBY.
S.M
CH
VOL
P.M
1:
Remote control sensor.
2:
Indicator LED: BLUE
RED
POWER ON.
STANDBY.
3: Side panel keys
REAR Connections
VIDEO
L
R
Y
Pb
Pr
AC-INPUT
100-240V~50/60Hz
COMPONENT
COMPOSITE
All the terminals are (from left to right):
POWER SOCKET, VIDEO, AUDIO INPUT, YPbPr INPUT
Note: AV and YPbPr share one audio channel.
SIDE Connections
HDMI1
HDMI2
USB
VGA
HEADPHONE PC AUDIO COAXIAL
RF
All the terminals are (from left to right):
HDMI1, HDMI2, USB, VGA, HEADPHONE, PC AUDIO, COAXIAL, RF.
Note: 1. When HDMI1 has an input signal coming from a DVI source then the audio input signal must be
connected to the PC audio input.
2. When HDMI2 has an input signal coming from a DVI source then the audio input signal must be
connected to the YPbPr/AV audio input.
- 23 -
REMOTE CONTROL
1
27
9
RETURN
DISPLAY
AUDIO
SUBTITLE
28
30
23
CC/
25
MTS/
19
21
20
REPEAT
MENU
GOTO
SETUP
22
16
29
24
26
CH LIST/
EPG/
FAV/
ASPECT
15
17
18
3
8
11
4
5
TV
DISPLAY
12
13
S.M
6
CH
VOL
14
P.M
7
1: POWER
To set the TV standby or on.
2: NUMBER KEY
For direct access to program.
3:
Displays the main on-screen menu.
4: CURSOR
To move within the menu.
5: EXIT
Used to exit menu.
6: VOL+/VOLTo adjust sound level.
7: P.M
To switch picture mode.
8:
Press to display and select the available video sources.
9: MUTE
To disable or enable the sound.
10: RECALL
To access the previously viewed program.
11: ENTER
Confirms selection.
12: TV DISPLAY
Displays/removes the program Information
13: S.M
To switch sound mode.
14: CH+/CHTo access the next or previous Program.
15: ASPECT
To change picture aspect .
16: CH LIST /
Used to display the channel list / Eject or Insert the disc.
17: EPG
Display all the information of DTV programs.
18: FAV
Used to access your favourite channels in digital TV mode.
19: CC
Enable or disable the CC function.
20: MTS
Switch the sound stereo.
2
10
For a description of the DVD player function buttons
on the remote, please refer to page 20 of this manual.
- 25 -
- 26 -
A
B
C
I2C-SCL
I2C-SDA
4
14
15
MODE0
R905
100R
5
100R 13
R902
9
7
5
3
13
11
13
11
9
7
5
3
GND
NC9
MODE0
I2C_SDA
I2C_SCL
VSS
NC/CP_2.0B
24
100R 12
11
14
12
10
8
6
4
R901
14
IPOD_IN_L
4
12
10
8
6
4
IPOD_IN_R
IPOD_CVBS
IPOD_C
R918
GND
R919
4
NC1
MODE1
NC2
NRESET
VCC
1
2
3
4
5
22
U25
100R
10K
IPOD_RX
IPOD_TX
NC10
16
D
DIP-14(2*7)
1 1
+5V
NC7
NC11
17
CN8
2 2
23
GND
NC5
NC12
18
9
19
IPOD_Y
10
NC8
4
NC3
8
NC4
NC13
7
NC14
20
6
GND
21
4
R903
10K
MODE1
+3.3V
RESET_CP
C504
0.1uF
C503 0.1uF
+3.3V
3904
Q9
3
C527
CP_RESET
4
IPOD_C
75R
C32
75R
R98
R125
33R
33R C31
R97
R124
75R
IPOD_Y
33R C30
R96
R123
C66 560pF
2.2uF
47nF
47nF
47nF
4
4
IPOD_SV-Cin
IPOD_SV-Yin
4
2
1
APPRD:
VER:1.0
DESIGN:George Guo
9
CHECKED:
MODEL: MSAV3207-K3
OF
SHEET:
TITLE: IPOD IF
9
Date: Feb. 3,2010
4
IPOD_CVBS_IN 4
IPOD-Lin
IPOD-Rin
1
pin
Communication I2C ADDR
Mode
Write Read
MODE1 MODE0
0
0
SPI slave
--1
0
0x20 0x21
I2C slave
1
1
0x22 0x23
R167
1 1K
R163
1K
C526
C48 560pF
2.2uF
IPOD_CVBS
12K
12K
R115
22K
IPOD_IN_L
R126
2
R127
R114
22K
IPOD_IN_R
+3.3V
RESET_CP
IPOD_DETECT 4
+3.3V
4
3
3
2
5
A
B
C
D
7. Electrical parts
7-1. Circuit Diagram
A
B
C
D
13
14
15
16
0.1uF
C25
3
+12V
R278
10K
R280
10K
R279
10K
R276
1K
R282
NC/1K
U13
VIN
C83
0.1uF
VOUT
5
820R
10uF
150R
3
C82
R156
Vpp
80mv
R153
2
+8V
If use single saw filter(internal),
Delete R276,R280
Add R283(0R)
Delete Q59
Delete C73
VIN
D_RF_AGC
R283
NC/0R
4
2
4
4
R157
680R
U12
AMS1084CD-ADJ
VOUT
+5V_LDO
DEMOD_IF_AGC 4
For silicon tuner
Closed to MstIC
C142
22nF
IF-5V
C139
22nF
IF-5V
R281
10R
C143
0.1uF
+3.3V_SB
R437
10K
R440
100K
RF_AGC_SEL 4
RF_AGC
Q59
3906
AMS1084CD-ADJ
RF_AGC
IFAGC
+5V
Q58
3904
R438
10K
T_RF_AGC
5V-Tuner
20pF 20pF
IF+
IF-
4
4
TUNER_I2C_SCL
TUNER_I2C_SDA
RS6
1M
CS12
1nF
3.3VCC_TM
RS25
0R
CS28
100uF/16V
CS10
56pF
CS18
82pF
RS7
RS5
100uF/16V
CS25
+
+5V
CS3
NC
RS18
LS14
120R
0R
NC
CS27
120ohm_FB
NC
0R
RS19
RS13
Vdd_A1.6V_D
RS12
RS10
Put on digital GND plane
Vdd_A1.6V
VBATT_A5
AS
VAGC2
XTAL_N
LS1
2.2uF
CS2
0.1uF
120ohm_FB
CS1
MXL302RF_V8_F1_32
VBATT_A3
IDAC
LNA_IN
VDD_DNX2
24.000MHZ
1
8
7
6
0.1uF
3
2
1
5
Y2
U4
CS4
1nF
CS17
2
0.1uF
4
0.1uF
CS9
120ohm_FB
LS2
120ohm_FB
3.3VCC_T
LS8
12nH
NC
0R
1.8VCC
LS6
120ohm_FB
302RF V8
DNP
0
AMS1117-3.3
US1
LS9
3.3VCC_T
Vdd_A1.6V
1.8VCC
LS7
330nH
CS29
0.1uF
LS11
220nH
RS24
NC
CS16
180pF
3.3VCC_T
RS8
1M
DS1
BAV99
CS13
CS14
39pF
27pF
RS3
10K
3.3VCC_T
301RF V8
DNP
0
LS3
0.1uF
Vdd_A1.6V_D
0.1uF
CS22
100R
22
23
24
VBATT_A4
CS26
2.2uF
LS15
17
CS8
SSDA
3.3VCC_T
SSCL
120ohm_FB
2.2uF
CS20
4700pF
RS17
100R
RS16
100R
C84
0.1uF
220R
R154
Vpp
80mv
+ EC16
470uF/16V
FB5
FB56R/1A
4
+ EC6
470uF/16V
5V-Tuner
C8
0.1uF
5.19V 116mA (ATV)
C559
0.1uF
AIF
+8V
10nF
C73
R138
C72
NC/1.5K
R140
R137
NC/56R
AGND
NC/10uF NC/15nF
C71
NC/100R
R139
NC/680R
1
Q12
NC/2SC2216
R141
NC/4.7K
R150
NC/22R
3
NC/39R
0R
R151
R271
L7
NC/1uH
C220
10nF
R288
0R
R290
0R
C214 10nF
VIFP_OUT
L3
NC/2.2uH
VIFN_OUT
SIFP_OUT-
SIFP_OUT+
1
2
M3953M
U23
IN
ING
2
1
M9370M
OUT2
5
4
4
5
RS14
4.7K
C222 0.1uF VIF_P
L4
NC/2.2uH
C221 0.1uF VIF_M
SIF_IN+
SIF_IN-
4
4
2
B0
B1
4
4
3
2
1
3
2
1
3.3VCC_T
RS23
+1.8V
Vdd_A1.6V_D
B0
GND
Vdd_A1.6V_D
A
VCC
S
3.3VCC_T
4
5
6
A
4
B1
GND
U29
FSA3157P6X
VCC
S
U28
FSA3157P6X
5
6
T_SCL
T_SDA
RS15
4.7K
120ohm_FB
120ohm_FB
47R
120ohm_FB
IFS2
0.1uF
IFS1
C20
+5V
If use single saw filter(internal),
Delete these parts of this area
OUT1
SAWOUT2
OUT1
ING
IN
U22
0.1uF
2
CS23 CS24
18PF 18PF
LS10
RS9
LS12
LS13
CS19
T_RF_AGC
IFAGC
4700pF
NC/1K
CS7
RS1
Vdd_IO
3.3VCC_T
F1
GND_DIG
VREG_D_OUT
18
VREG_D_IN 19
20
VDD_REF_SX 21
IF_OUTN2
IF_OUTP2
IF_OUTN
CS5
RS20
Important:
Analog GND and digital GND is still separate,
but through Paddle GND connecting them,
please talk to SYU if anything not understood
4
7
8
9
10
75 ohm Line
1
2
5
6
F Conn
Vdd_RF_VCO_LO_3V
RF Input
Port
LNA GND
JS1
CS33
10nF
Pin 1 R23
Pin 1 R24
301RF V7 MM
0
DNP
1
IFAGC
C149 C150
100R
IF_AGC R534
IF+
IFAIF
RF AGC Switch
GND
GND
GND
GND
47R
47R
2
T_SCL R532
T_SDA R533
33
T_RF_AGC
3
3.3VCC_T
CLK_OUT
10
5V-Tuner
GND_XTAL
11
1
2
3
4
5
6
7
8
9
10
11
12
VREG_A_OUT1
12
3
LS4
13
NC
+5V
RF-AGC
BT
AS
SCL
SDA
B2
IF-AGC
DIF2
DIF1
AIF
3
LS5
VBATT_A1
DA58GT-13-E
1
33nH
SCL
14
U24
4
TAB
ADJ
1
4
TAB
ADJ
1
2
4
3
120nH
SDA
15
PADDLE
3.6nH
TF_1
32
XTAL_P
9
30
TF_2
31
VDD_DNX1
29
TF_3
28
VREG_A_OUT2
26
VAGC1
25
IF_OUTP
27
VBATT_A2
VDD_IO
16
4
3
2
GND
3
5
SAW
- 27 3
RS27
470R
RS26
1K
RF_AGC_SEL
CS39
APPRD:
CHECKED:
DESIGN:George Guo
1
Date: Feb. 3,2010
8 OF 9
VER:1.0
CS36
0.1uF
+5V
US2
AMS1117-ADJ
IFS2
IFS1
IF-
SHEET:
CS32
0.1uF
1K
1K
IF+
LS16
220nH
MODEL: MSAV3207-K3
100uF/16V
RS22
RS21
100R
CS31
39pF
Close Silicon Tuner
100R
TITLE: TUNER
NC
VIFP_OUT
C263 4700pF R217
CS35 10nF
1.8VCC
VIFN_OUT
1
10nF SIFP_OUT+
391R CS30 10nF SIFP_OUT-
391R CS6
C262 4700pF R216
CS34 10nF
RS4
RS2
1
4
2
ADJ
ADJ
GND
IN
3
IN
OUT
OUT
A
B
C
D
A
B
C
AR-
FADE
NC/4.7K
R777
+5V
C728 NC/1uF
AL+
R793
NC/0R
VOLUME
1
8
Add
AL-
10
C714
1uF
9
FADE
7
6
5
4
3
C704
NC/1uF 2
C705 NC/1uF
C729 NC/1uF
3.3V/Gain:32dB
AR+
PAM8610
ϡ⫼4558ᯊˈⷁ᥹
R242
10K
47K
C743
NC/1uF
C744
NC/10uF
+12V
R246
6 -
5 +
ROUT-
ROUT+
AMP_RIN C131 1uF
C746 NC/220nF C745 NC/220nF
+12V
C764 C765
FB705
FB706
NC/FB/1206 NC/1nFNC/1nFNC/FB/1206
33K
7
LINN
LINP
FADE
5
AGND1
REFGND
VOLUME
VREF
AVDD
RINP
RINN
NC/1nF
C749
+12V
C719
NC/10uF
NC/1uF
C715
LOUT-
FB707
NC/FB/1206
NC/220nF
C721
NC/1uF
C732
C763
NC/1nF
LOUT+
COSC
ROSC
AGND
MUTE
AVCC
V2P5
AGND
VCLAMPL
C736
NC/10uF
FB708
NC/FB/1206 +12V
NC/220nF
C731
NC/PAM8610
U27
SD
VCLAMPR
C747
NC/1uF
NC/10uF
C748
R243 100R
41
thermal
R241
11
C130
2.2uF
40
PGNDR
PGNDL
AMP_RIN0
U15B 4558
VCC-OP2
33K
R233 100R
12
ROUTN
4VA
R237
AMP_LINC127 1uF
PVCCR
PVCCL
ϡ⫼4558ᯊˈⷁ᥹
R231
10K
U15A
4558
1
C123
10uF
VCC-OP2
ROUTN
LOUTN
13
C125
2.2uF
2 -
3 +
+
LOUTN
14
BSRP
AMP_LIN0
8
BSLN
15
D
R226
10K
8
4
4
38
R227
47K
37
R236
10K
34
BSLP
16
BSRN
4VA
35
17
+
36
LOUTP
C122
10uF
39
NC
R245
R778
33R
33
ROUTP
LOUTP
18
ROUTP
C128
10nF
C132
10nF
AR+
R794
NC/1K
C738 NC/1uF
C740
NC/0.1uF
AMP-MUTE
C737
NC/10uF
+12V
NC/33R
R292
MUTE
4
4
Default:PAM8610
C739 NC/220pF
21
R785
NC/120K
MUTE_PAM
C741 NC/1uF
SD
C742 NC/1uF
22
23
24
25
26
27
28
29
30
AL+
12K
R235
12K
R244
+
470uF/25V
EC7
+12V
PWD_MT
AMP-MUTE
0.1uF
C135
MUTE
TDA1517
AMP_LIN
C124
470pF
EC12 +
R239
4.7K
1N4148
D12
100uF/25V
47K
R300
PWD_MT
FOR S2
2
R284
AR+
C134
2.2uF
ROUT#
SVRR
LOUT#
AL+
1
1
3904
Q33
3904
Q23
E45
1
2
3
4
5
6
7
8
9
10
Q35
3904
MUTE ON
AMP-MUTE
AR+
Q24
3904
1
1
IN1
SGND
SVRR
OUT1
PGND
OUT2
VCC
M/SB
IN2
GND/HS
U16
NC/V800AA
AL+
MUTE OFF
AMP-MUTE
1K
1K
PH_L
R230
1K
C133
2.2uF
+12V
Q20
3904
MUTEDD
1
R274
R228
22R
Q25
R299
0R
3904
R275
10K
3
NC/10K
R266
+3.3V_SB
20
19
18
17
16
15
14
13
12
11
MUTE
GND/HS
GND/HS
GND/HS
GND/HS
GND/HS
GND/HS
GND/HS
GND/HS
GND/HS
GND/HS
TPA1517
PH_L
R267
10K
+12V
AMP_RIN
EC9
220uF/16V
+
EC8
220uF/16V
3
470R
R260
1N4148
D13
1N4148
D9
PWD_MT
220uF/25V
270K
2
EC11
470uF/16V
1
2
1
R229
22R
1
1
R285
R322
Q21
3906
EC10
470uF/16V
R240
4.7K
EC14
R268
ROUT#
LOUT#
PWD_MT
FOR S2
C126
470pF
PH_Drive
3
2
NC
R234
32
PVCCR
PVCCL
19
PGNDR
2
+8V
31
PGNDL
20
1
2
3
Q19
3904
PH_R
R256
NC/0R
+12V
Q22
3904
NC/3K
R341
+5V
Mute Circuit
10K
Add
R261
10K
MUTEDD
SPEAKER
4
3
2
1
J11
R255 +5VSB
NC/0R R888
0R
NC/0R
E44
NC/V800AA
R232
1K
R249 R250
LOUT+
LOUTROUTROUT+
2
AUDIO Pre AMP
5
2
PH_R
2
R788 NC/1K
6
GAIN1
GAIN1
R366
0R
R363
10K
R365
GAIN0 NC/10K
VOLUME
+3.3V_SB
R755
NC/0R_0805
AR+ C753 NC/1uF
14
13
12
11
10
9
8
7
5
4
3
2
1
GAIN0
C720 NC/1uF +12V
AL1-
MUTE#
C726 NC/1uF
R789
R790 NC/10K NC/10K
C727 NC/1uF
C750 NC/1uF
AR1-
C751 NC/1uF
AL+ C752 NC/1uF
MUTE
For Pam860 gain set
R362
NC/10K
R364
NC/10K
2
PBTL
NC
RINP
RINN
PLIMIT
GVDD
AGND
AVCC
GAIN1
GAIN0
LINN
LINP
FAULT
SD
U19
TPA3110D2
27
28
+12V
NC/220nF
NC/FB/1206
NC/FB/1206
1
APPRD:
Date: Feb. 3,2010
VER:1.0
CHECKED:
7 OF 9
C713
NC/1nF
ROUT-
ROUT+
C707
NC/1nF
C709
NC/1nF
LOUT-
SHEET:
+12V
FB704 NC/FB/1206
NC/220nF
NC/220nF
FB703
FB702
LOUT+
NC/FB/1206 C706
NC/1nF
FB701
DESIGN:George Guo
C734
C735
C733
C730 NC/220nF
to subwoofer
to speaker
for subwoofer
for speaker
MODEL: MSAV3207-K3
15
16
17
18
19
20
21
22
23
24
25
26
Lout1/2#
RLout1/2
AL1/2 in
AL/R
in
1
TITLE: AUDIO
PVCCR
PVCCR
BSPR
OUTPR
PGND
OUTNR
BSNR
BSNL
OUTNL
PGND
OUTPL
BSPL
PVCCL
PVCCL
TPA3113D2
GND
29
+
1
2
3
2
3
2
3
2
3
+
+
1
- 28 2
0R
3
0R
A
B
C
D
4
3
2
1
J17
1
2
3
4
NC/USB1IN
CON4
J2
5
5VUSB1
R158
R162
LCD_OP
G2_RXE0G0_RXE1B6_RXE2B4_RXECB2_RXE3B0_RXE4-
R6_RXO0R4_RXO1R2_RXO2R0_RXOCG6_RXO3G4_RXO4-
4
4
ON_USB1
USB0_DM
USB0_DP
4
4
4
4
4
4
4
4
4
4
4
4
4
ON_USB1
I2C-SCL
I2C-SDA
VCC-Panel
OVERDRIVER
LCD_OP
G2_RXE0G0_RXE1B6_RXE2B4_RXECB2_RXE3-
R0_RXOC-
USB0_DM
5.1R USB0_DP
5.1R
J9 2X20,2.0,TCON
2
1 1
4
3 3
6
5 5
8
7 7
10
9 9
12
11 11
14
13 13
16
15 15
18
17 17
20
19 19
22
21 21
24
23 23
26
25 25
28
27 27
30
29 29
32
31 31
34
33 33
36
35 35
38
37 37
40
39 39
USB Interface
PANEL-ON/OFF#
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
V800AA
A
B
C
G3_RXE0+
G1_RXE1+
B7_RXE2+
B5_RXEC+
B3_RXE3+
R1_RXOC+
VCC-Panel
G3_RXE0+
G1_RXE1+
B7_RXE2+
B5_RXEC+
B3_RXE3+
B1_RXE4+
4
4
4
4
4
4
6
5
D
R7_RXO0+
R5_RXO1+
R3_RXO2+
R1_RXOC+
G7_RXO3+
G5_RXO4+
4
4
4
4
4
4
LVDS CONNECTOR
E80
+5V
+3.3V
R202
R203 NC
NC
1
1
2
3
4
NC
8
7
6
5
R205
NC
R201
U8
NC/TPS2051D
R204
NC
PANEL-ON/OFF#
OVERDRIVER
NC
R200
+3.3V
+5V
3
USB_DETEC1
+3.3V
USB_DETEC1
3
NC/NSMD050
5VUSB1
NC/10K
USB_DETEC1
R196
F1
Panel_ON
R320
4.7K
+12V
+5V
100uF/16V
+
APPRD:
VER:1.0
2
D
A
B
C
NC/220uF/16V
EC99
CHECKED:
1
C157 +
0.1uF
SHEET:
6 OF 9
C158
NC/0.1uF
PANEL-ON/OFF#
VCC-Panel
DESIGN:George Guo
Q34
3904
R318
100K
C156 NC/10nF
AO3407
3
MODEL: MSAV3207-K3
1
10K
R326
0.1uF
C155
Q31
2
4.99V 625mA (1080P)
Date: Feb. 3,2010
Q32
3904
R305
4.7K1
4.7K
R321
+5V
R323 NC
R313
0R/0805
1
TITLE: LVDS&USB IF
L: Panel active
C118
5VUSB1
4
2
1
4
2
R194
NC/51K
R195
3
2
3
2
1
2
5
R193
2
V800AA
1
E81
NC/100K
- 29 R192
10K
10K
A
B
C
D
R83
100R
MA_MCLKZ
5
C446
10nF
R84
100R
75R
MIUA_A13 R73
MA_MCLK
RP13
RP39
A_MVERF
C428
10nF
R107
10K
1 3 5 7
1 3 5 7
R116
10K
+1.8V
22RX4
MIUA_MCLK
MIUA_MCLKZ
22RX4
MIUA_DQS0
MIUA_DQSB0
2 4 6 8
2 4 6 8
MA_CKE
MA_A0
MA_A1
MA_A2
MA_A3
MA_A4
MA_A5
MA_A6
MA_A7
MA_A8
MA_A9
MA_A10
MA_A11
MA_A12
MA_A13
MA_BA0
MA_BA1
MA_BA2
MA_MCLK
MA_MCLKZ
MA_DQS0
MA_DQSB0
K8
K2
M8
M3
M7
N2
N8
N3
N7
P2
P8
P3
M2
P7
R2
R8
L2
L3
L1
J8
CK
CKE
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
BA0
BA1
BA2
CK
1UF
C433
4
+1.8V
Vpp
200mv
RAS
CAS
WE
CS
ODT
C432
0.1uF
C445
0.1uF
C441
0.1uF
C442
0.1uF
4
U9
DDRII512M(P3R12E4JFF-G8E)
75R
R13
C430
0.1uF
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
UDQS
UDQS
UDM
LDQS
LDQS
LDM
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
3
9
MIUA_DQ15
MIUA_DQ8
MIUA_DQ10
MIUA_DQ13
MIUA_DQ7
MIUA_DQ0
MIUA_DQ2
MIUA_DQ5
MA_A12
MA_A7
MA_A9
MA_A3
MA_A5
MA_A10
MA_A1
MA_BA2
RP3
RP4
RP7
RP6
1
APPRD:
CHECKED:
RP18 MA_A2
MA_A0
MA_CASZ
MA_RASZ
DESIGN:George Guo
OF
MIUA_DQ6
MIUA_DQ1
MIUA_DQ3
MIUA_DQ4
RP2
RP5 MA_A4
MA_A6
MA_A8
MA_A11
MIUA_DQ11
MIUA_DQ12
MIUA_DQ9
MIUA_DQ14
RP1
VER:1.0
5
MIUA_A2 75RX4
MIUA_A0
MIUA_CASZ
MIUA_RASZ
MIUA_A4 75RX4
MIUA_A6
MIUA_A8
MIUA_A11
MIUA_A5 75RX4
MIUA_A10
MIUA_A1
MIUA_BA2
MIUA_A1275RX4
MIUA_A7
MIUA_A9
MIUA_A3
MA_DQ7 22RX4
MA_DQ0
MA_DQ2
MA_DQ5
MA_DQ15 22RX4
MA_DQ8
MA_DQ10
MA_DQ13
MA_DQ6 22RX4
MA_DQ1
MA_DQ3
MA_DQ4
MA_DQ11 22RX4
MA_DQ12
MA_DQ9
MA_DQ14
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
SHEET:
2
MIUA_DQM0
R1 MIUA_DQM1
R66
MIUA_DQS1
MIUA_DQSB1
C468
0.1uF
MIUA_MCLK
MIUA_MCLKZ
MIUA_MCKE
MIUA_WEZ
MIUA_CASZ
MIUA_RASZ
MIUA_BA0
MIUA_BA1
MIUA_BA2
MIUA_ODT
MIUA_DQSB0
MIUA_DQS0
MIUA_DQSB1
MIUA_DQS1
MIUA_DQM0
MIUA_DQM1
MIUA_DQ[15:0]
MIUA_A[13:0]
1
MODEL: MSAV3207-K3
22R
22R
RP12
MA_BA0
MA_BA1
MA_CKE
MA_WEZ
C444
0.1uF
MIUA_MCLK
MIUA_MCLKZ
MIUA_MCKE
MIUA_WEZ
MIUA_CASZ
MIUA_RASZ
MIUA_BA0
MIUA_BA1
MIUA_BA2
MIUA_ODT
MIUA_DQSB0
MIUA_DQS0
MIUA_DQSB1
MIUA_DQS1
MIUA_DQM0
MIUA_DQM1
MIUA_DQ[15:0]
MIUA_A[13:0]
TITLE: DDR2_16
MA_DQ8
MA_DQ9
MA_DQ10
MA_DQ11
MA_DQ12
MA_DQ13
MA_DQ14
MA_DQ15
MA_DQS1
MA_DQSB1
MA_DQM1
C8
C2
D7
D3
D1
D9
B1
B9
B7
A8
B3
RP15
C431
0.1uF
2
Date: Feb. 3,2010
MA_DQS0
MA_DQSB0
MA_DQM0
MA_DQ0
MA_DQ1
MA_DQ2
MA_DQ3
MA_DQ4
MA_DQ5
MA_DQ6
MA_DQ7
1 3 5 7
F7
E8
F3
G8
G2
H7
H3
H1
H9
F1
F9
22RX4
MA_DQS1
MA_DQSB1
MIUA_BA075RX4
MIUA_BA1
MIUA_MCKE
MIUA_WEZ
C443
0.1uF
3
2 4 6 8
+1.8V
A_MVERF
J9
M9
R1
E1
A1
C1
A9
C3
C7
C9
G1
G3
G7
G9
E9
J1
J2
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDL
VREF
5
1 3 5 7
2 4 6 8
7 5 3 1 1 3 5 7
- 30 MA_RASZ
K7
MA_CASZ
L7
MA_WEZ
K3
L8
MA_ODT K9
8 6 4 2 2 4 6 8
MIUA_ODT
1 3 5 7
8 6 4 2
2 4 6 8
8 6 4 2
7 5 3 1 1 3 5 7
8 6 4 2 2 4 6 8
7 5 3 1
VSSDL
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSS
VSS
VSS
VSS
VSS
8 6 4 2
7 5 3 1
J7
B8
B2
D2
D8
E7
F2
F8
H8
H2
A7
J3
N1
P9
E3
A3
7 5 3 1
A
B
C
D
A
B
C
D
REAR_AV
DVD_AV
SIDE_AV
IPOD_CVBS_IN
IPOD_SV-Yin
IPOD_SV-Cin
VCOM0
LINE_IN_0L
LINE_IN_0R
LINE_IN_1L
LINE_IN_1R
LINE_IN_2L
LINE_IN_2R
IPOD-Rin
IPOD-Lin
DVD_IN_R
DVD_IN_L
AOUT_R1
AOUT_L1
AMP_RIN0
AMP_LIN0
SPDIF_OUT
R289
R308
MIUA_MCLK
MIUA_MCLKZ
MIUA_MCKE
MIUA_WEZ
MIUA_CASZ
MIUA_RASZ
MIUA_BA0
MIUA_BA1
MIUA_BA2
MIUA_ODT
MIUA_DQSB0
MIUA_DQS0
MIUA_DQSB1
MIUA_DQS1
MIUA_DQM0
MIUA_DQM1
MIUA_DQ[15:0]
MIUA_A[13:0]
HDMI-CEC
HDMI0-RX0P
HDMI0-RX0N
HDMI0-RX1P
HDMI0-RX1N
HDMI0-RX2P
HDMI0-RX2N
HDMI0-CLKP
HDMI0-CLKN
HDMI0-HPDIN
HDMI1-RX0P
HDMI1-RX0N
HDMI1-RX1P
HDMI1-RX1N
HDMI1-RX2P
HDMI1-RX2N
HDMI1-CLKP
HDMI1-CLKN
HDMI1-HPDIN
HDMI2-RX0P
HDMI2-RX0N
HDMI2-RX1P
HDMI2-RX1N
HDMI2-RX2P
HDMI2-RX2N
HDMI2-CLKP
HDMI2-CLKN
HDMI2-HPDIN
3 HDMI2-SCL
3 HDMI2-SDA
3
3
3
3
3
3
3
3
3
3 HDMI1-SCL
3 HDMI1-SDA
3
3
3
3
3
3
3
3
3
3 HDMI0-SCL
3 HDMI0-SDA
3
3
3
3
3
3
3
3
3
3
HDMI Block
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
DTV-IFN
DTV-IFP
HDMI2-SCL
HDMI2-SDA
HDMI2-RX0P
HDMI2-RX0N
HDMI2-RX1P
HDMI2-RX1N
HDMI2-RX2P
HDMI2-RX2N
HDMI2-CLKP
HDMI2-CLKN
HDMI2-HPDIN
HDMI1-SCL
HDMI1-SDA
HDMI1-RX0P
HDMI1-RX0N
HDMI1-RX1P
HDMI1-RX1N
HDMI1-RX2P
HDMI1-RX2N
HDMI1-CLKP
HDMI1-CLKN
HDMI1-HPDIN
HDMI0-SCL
HDMI0-SDA
HDMI-CEC
HDMI0-RX0P
HDMI0-RX0N
HDMI0-RX1P
HDMI0-RX1N
HDMI0-RX2P
HDMI0-RX2N
HDMI0-CLKP
HDMI0-CLKN
HDMI0-HPDIN
MIUA_MCLK
MIUA_MCLKZ
MIUA_MCKE
MIUA_WEZ
MIUA_CASZ
MIUA_RASZ
MIUA_BA0
MIUA_BA1
MIUA_BA2
MIUA_ODT
MIUA_DQSB0
MIUA_DQS0
MIUA_DQSB1
MIUA_DQS1
MIUA_DQM0
MIUA_DQM1
MIUA_DQ[15:0]
MIUA_A[13:0]
D_RF_AGC
DEMOD_IF_AGC
220R/0R
220R/0R
AOUT_R1
AOUT_L1
AMP_RIN0
AMP_LIN0
SPDIF_OUT
LINE_IN_0L
LINE_IN_0R
LINE_IN_1L
LINE_IN_1R
LINE_IN_2L
LINE_IN_2R
IPOD-Rin
IPOD-Lin
DVD_IN_R
DVD_IN_L
CVBS_OUT
REAR_AV
DVD_AV
SIDE_AV
IPOD_CVBS_IN
IPOD_SV-Yin
IPOD_SV-Cin
VCOM0
YPbPr_RINYPbPr_RIN+
YPbPr_GINYPbPr_GIN+
YPbPr_BINYPbPr_BIN+
YPbPr_SOG
DDR2-SDRAM Block
8 D_RF_AGC
10nF
C141
8 IFC140
8 IF+
10nF
8 DEMOD_IF_AGC
DIF BLOCK
2
2
7
7
2
LINE OUT
2
2
2
2
2
2
9
9
2
2
LINE IN
Audio Block
2 CVBS_OUT
2
2
2
9
9
9
2
CVBS Block
YPbPr_RINYPbPr_RIN+
YPbPr_GINYPbPr_GIN+
YPbPr_BINYPbPr_BIN+
YPbPr_SOG
5
I2C-SDA
I2C-SCL
DVD_ON/OFF
RF_AGC_SEL
BRI_ADJ-PWM3
Panel_ON
AMP-MUTE
IPOD_TX
IPOD_RX
IPOD_DETECT
CP_RESET
LCD_OP
SIF_INSIF_IN+
C369
10uF
+3.3V_SB
R51
1M
C3
12pF
R56
10K
D3
BAV99
2
Q1
3906
R61
47K
R57
+5VSB
C370
10uF
4.7K
4.7K
100R System-RST
AUVRP
AUVAG
AUVRM
C4
12pF
XTALO
C6
1uF
24.000MHz
Y1
Close to IC
with width trace
1uF
C5
Reset
XTALI
R9
USB0_DP
USB0_DM
SIF_INSIF_IN+
VIF_P
VIF_M
B4_RXECB5_RXEC+
G2_RXE0G3_RXE0+
G0_RXE1G1_RXE1+
B6_RXE2B7_RXE2+
B2_RXE3B3_RXE3+
B0_RXE4B1_RXE4+
R0_RXOCR1_RXOC+
R6_RXO0R7_RXO0+
R4_RXO1R5_RXO1+
R2_RXO2R3_RXO2+
G6_RXO3G7_RXO3+
G4_RXO4G5_RXO4+
PH_DETECT
UART-RX
UART-TX
BLK_ON
R23
PW_ON/OFF R30
RF_AGC_SEL R26
BRI_ADJ-PWM3 R24
Panel_ON
R21
AMP-MUTE
R28
IPOD_TX
R64
IPOD_RX
R65
IPOD_DETECTR75
CP_RESET R72
LCD_OP
R89
I2C-SDA
R309
I2C-SCL
R307
DVD_ON/OFFR324
+3.3V
4.7K
4.7K
4.7K
10K
10K
10K
10K
4.7K
4.7K
10K
10K
1K
TUNER_I2C_SCL R306 4.7K
TUNER_I2C_SDA
4.7K
R304
System XTAL
6 USB0_DP
6 USB0_DM
USB Block
8
8
8
8
VIF_P
VIF_M
B4_RXECB5_RXEC+
G2_RXE0G3_RXE0+
G0_RXE1G1_RXE1+
B6_RXE2B7_RXE2+
B2_RXE3B3_RXE3+
B0_RXE4B1_RXE4+
6
6
6
6
6
6
6
6
6
6
6
6
NTSC RF
R0_RXOCR1_RXOC+
R6_RXO0R7_RXO0+
R4_RXO1R5_RXO1+
R2_RXO2R3_RXO2+
G6_RXO3G7_RXO3+
G4_RXO4G5_RXO4+
6
6
6
6
6
6
6
6
6
6
6
6
LVDS Block
PH_DETECT
2 UART-RX
2 UART-TX
1 BLK_ON
1 PW_ON/OFF
9
9
2
8
1
6
7
9
9
9
9
6
8 TUNER_I2C_SCL
8 TUNER_I2C_SDA
+5V
PWM
GPIO
Debug Port
MSD318-ATSC
DP_P1
DM_P1
DP_P0
DM_P0
A_RX0N
A_RX0P
A_RX1N
A_RX1P
A_RX2N
A_RX2P
A_RXCN
A_RXCP
DDCDA_CK
DDCDA_DA
HOTPLUGA
B_RX0N
B_RX0P
B_RX1N
B_RX1P
B_RX2N
B_RX2P
B_RXCN
B_RXCP
DDCDB_CK
DDCDB_DA
HOTPLUGB
C_RX0N
C_RX0P
C_RX1N
C_RX1P
C_RX2N
C_RX2P
C_RXCN
C_RXCP
DDCDC_CK
DDCDC_DA
HOTPLUGC
CEC
XTAL_OUT
XTAL_IN
DDCR_DA
DDCR_CK
IRIN
RESET
SAR0
SAR1
SAR2
SAR3
GPIO_PM0
GPIO_PM1
GPIO_PM2
GPIO_PM3
GPIO_PM4
GPIO_PM5
GPIO_PM6
GPIO_PM7
SPI_CSZ
SPI_DO
SPI_DI
SPI_CK
GPIO0(UART_TX1)
GPIO1(UART_RX1)
GPIO2
DDCA_DA
DDCA_CK
PWM0
PWM1
PWM2
PWM3
NAND_IO_0
NAND_IO_1
NAND_IO_2
NAND_IO_3
NAND_IO_4
NAND_IO_5
NAND_IO_6
NAND_IO_7
PF_OND_D8
PF_OND_D9
PF_OND_D10
PF_OND_D11
PF_OND_D12
PF_OND_D13
PF_OND_D14
PF_OND_D15
PF_OND_A0
PF_OND_A1
PF_OND_A2
PF_OND_A3
PF_OND_A4
PF_OND_A5
PF_OND_A6
PF_OND_A7
PF_OND_A8
PF_OND_A9
PF_OND_A10
PF_OND_A11
PF_OND_A12
PF_OND_A13
PF_OND_A14
PF_ALE
PF_CE0Z
PF_CE1Z
PF_OEZ
PF_WEZ
PF_RBZ
NAND_WPZ/PF_OND_A15
USB Hostx2
HDMI Inx3
XTAL
I2C-Master
PM Domain
Parallel Flash
U11C
H6
H4
K5
N6
M6
4
W15
Y15
AA15
V13
K21
K20
K19
L20
L19
M20
M21
M19
L16
K16
K17
M18
M17
R19
K18
N18
V15
V17
R16
R18
V16
V18
N16
R17
M16
N17
P16
P17
L17
T15
U15
P19
N19
P20
N20
R20
N21
R21
W14
Y14
IPOD_TX
IPOD_RX
UART-TXD
UART-RXD
PWM0
PWM1
Panel_ON
BRI_ADJ-PWM3
USB0_DP
USB0_DM
HDMI0-RX0N
HDMI0-RX0P
HDMI0-RX1N
HDMI0-RX1P
HDMI0-RX2N
HDMI0-RX2P
HDMI0-CLKN
HDMI0-CLKP
HDMI0-SCL
HDMI0-SDA
HDMI0-HPDIN
HDMI1-RX0N
HDMI1-RX0P
HDMI1-RX1N
HDMI1-RX1P
HDMI1-RX2N
HDMI1-RX2P
HDMI1-CLKN
HDMI1-CLKP
HDMI1-SCL
HDMI1-SDA
HDMI1-HPDIN
HDMI2-RX0N
HDMI2-RX0P
HDMI2-RX1N
HDMI2-RX1P
HDMI2-RX2N
HDMI2-RX2P
HDMI2-CLKN
HDMI2-CLKP
HDMI2-SCL
HDMI2-SDA
HDMI2-HPDIN
HDMI-CEC
C5
B5
XTALO
XTALI
E3
F2
F3
G2
G1
G3
E1
E2
K6
G4
J5
B3
C2
C3
D2
D1
D3
B1
B2
A2
D5
D6
Y12
AA12
W12
AA13
Y13
W13
Y11
W11
Y10
W10
AA10
K4
I2C-SDA
I2C-SCL
AA5
Y5
U14
T14
IRIN
System-RST
SAR0
SAR1
E4
B6
E5
J6
A6
C7
BLK_ON
LCD_OP
PH_DETECT
DVD_ON/OFF
PW_ON/OFF
AMP-MUTE
LED_CTL
FLASH_WPN
SPI-CS0N
SPI-SDO
SPI-SDI
SPI-SCK
U9
V9
T10
T9
G5
U10
V10
T8
A3
C4
A4
B4
4
RGB Inx3
WPN
VCC-FLASH
8 6 4 2
C356
LINE_IN_0L
LINE_IN_0R
LINE_IN_1L
LINE_IN_1R
LINE_IN_2L
LINE_IN_2R
LINE_IN_3L
LINE_IN_3R
LINE_IN_4L
LINE_IN_4R
IFAGC
RF_TAGC
TGPIO0/UPGAIN
TGPIO1/DNGAIN
TGPIO2/ I2C_CLK
TGPIO3/ I2C_SDA
IP
IM
VIFP
VIFM
SSIF/SIFP
SSIF/SIFM
SPDIF IN
SPDIF OUT
I2S_IN_BCK
I2S_IN_SD
I2S_IN_WS
I2S_OUT_BCK
I2S_OUT_MCK
I2S_OUT_WS
I2S_OUT_SD
I2S_OUT_SD1
I2S_OUT_SD2
I2S_OUT_SD3
VRP
VAG
VRM
LINE_OUT_0L
LINE_OUT_0R
LINE_OUT_1L
LINE_OUT_1R
EARPHONE_OUTL
EARPHONE_OUTR
7
8
SP_SDO
6
5
4
3
2
1
DO
SO16-CS
NC4
NC3
NC2
NC1
VCC
HOLD
VCC-FLASH
SPI_CSN_1
0.1uF
7 5 3 1 RP40
22RX4
VCOM0
CVBS0P
CVBS1P
CVBS2P
CVBS3P
CVBS4P
CVBS5P
RIN0M
RIN0P
GIN0M
GIN0P
BIN0M
BIN0P
SOGIN0
HSYNC0
VSYNC0
RIN1M
RIN1P
GIN1M
GIN1P
BIN1M
BIN1P
SOGIN1
HSYNC1
VSYNC1
RIN2M
RIN2P
GIN2M
GIN2P
BIN2M
BIN2P
SOGIN2
CVBS_OUT1
Boot Loader SPI Flash
MSD318-ATSC
Front End
SPDIF
I2S IN/OUT
Audio In/Out
CVBS Inx6
U11D
AA6
Y6
Y7
V7
AA7
W6
W7
Y8
W8
Y9
AA9
W9
M5
C6
P4
P5
L4
F5
H5
F6
G6
L5
L6
D4
T7
U7
U8
V5
W5
U5
V6
U6
T6
AA3
Y3
W2
W1
AA2
W3
Y2
Y1
V4
W4
R5
U1
U3
U2
T3
T4
T1
T2
K1
K2
J3
J2
H2
H1
H3
N4
N5
M3
N2
K3
L1
L3
M2
L2
R4
P6
R2
R3
N1
N3
P2
P3
P1
SOIC8
208mil
WP/Vpp
VSS
NC5
NC6
NC7
NC8
DI
CLK
U7
MX25L3205D
9
10
11
12
13
14
15
16
DEMOD_IF_AGC
D_RF_AGC
CP_RESET
RF_AGC_SEL
TUNER_I2C_SCL
TUNER_I2C_SDA
C358
SPI_SCK
SPI_SDI
3
C181 0.1uF
WPN
R59
4.7K
FLASH_WPN
NC/20pF
R54
4.7K
+3.3V
A0
A1
A2
GND
U26
24C04
+3.3V
VCC
WP
SCL
SDA
8
7
6
5
I2C-SCL
I2C-SDA
C357
0.1uF
C359 C360
12pF 12pF
R60
10K
GND_EFUSE
I2C-SCL
DO not use Microchip EEPROM for I2C-SDA
U9
1
2
3
4
H16
U4
V3
Y4
AA4
N9
P9
P10
P11
P12
P13
P14
P15
B15
C20
C12
C17
T5
R6
R7
P7
N7
M7
P8
V1
V2
N10
N11
N12
N13
N14
N15
L7
M11
M12
M13
M14
M15
L10
L11
L12
L13
L14
L15
K11
K12
K13
K14
K15
D9
100R UART-RXD
100R UART-TXD
I2C address
at A4
R129
R128
R225R222
4.7K 4.7K
HDCP KEY
UART-RX
UART-TX
+3.3V_SB
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
GND_EFUSE
PWR/GND
MSD318-ATSC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
AVSS_PGA
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
DVDD
AVDD1P2_ADC
DVDD_NODIE
AVDD3.3V_ADC
AVDD3.3V_DVI
AVDD3.3V_DVI
AVDD3.3V_DVI
AVDD3.3V_DMPLL
AVDD_AU33
AVDD_EAR33
AVDD3.3V_MEMPLL
AVDD3.3V_MEMPLL
VDDP3.3V
VDDP3.3V
VDDP3.3V
AVDD2.5V_PGA
AVDD2.5V_ADCB
AVDD2.5V_ADCB
AVDD2.5V_AU
AVDD2.5V_REF_Demod
AVDD2.5V_MOD
AVDD2.5V_MOD
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
U11E
DEBUG PORT
K10
K7
J9
J10
J11
J12
J13
J14
J15
J16
SPDIF_OUT
DTV-IFP
DTV-IFN
VIF_P
VIF_M
SIF_IN+
SIF_IN-
AVSS_PGA M9
H7
H8
J7
J8
D10
D11
D12
D13
D14
E9
E10
E11
E12
E13
E14
F9
F10
F11
F12
F13
F14
G9
G10
G11
G12
G13
G14
H9
H10
H11
H12
H13
H14
H15
L49
FB/60R/0.3A
LC0603
C523
1uF
D15
D16
D17
D18
E16
E17
E15
E18
F15
DVDD_NODIE G15
VDDC
+3.3V_SB
+3.3V_SB
+3.3V_SB
+3.3V_SB
+3.3V_SB
AVDD2P5_PGA
2.5V_MAINCHIP
D7
D8
E8
F7
E7
G7
F8
F16
G16
F17
G17
H17
M10
K8
K9
L9
L8
M8
N8
AVDD_MEMPLL
VDDP
H18
H19
H20
H21
J18
J19
J20
J21
F18
G18
+1.8V
I2S_OUT_BCK
I2S_OUT_MCK
IPOD_DETECT
I2S_OUT_SD
AUVRP
AUVAG
AUVRM
AUOUTL0
AUOUTR0
AUOUTL1
AUOUTR1
LINE_IN_0L
LINE_IN_0R
LINE_IN_1L
LINE_IN_1R
LINE_IN_2L
LINE_IN_2R
IPOD-Lin
IPOD-Rin
DVD_IN_L
DVD_IN_R
CVBS_OUT
VCOM0
REAR_AV
IPOD_CVBS_IN
IPOD_SV-Yin
IPOD_SV-Cin
DVD_AV
SIDE_AV
VGA_HSYNC0
VGA_VSYNC0
YPbPr_RINYPbPr_RIN+
YPbPr_GINYPbPr_GIN+
YPbPr_BINYPbPr_BIN+
YPbPr_SOG
RINRIN+
GINGIN+
BINBIN+
3
TESTPIN
LVSYNC
LHSYNC
LDE
LCK
R_ODD6/LB0N/RLV6N
R_ODD7/LB0P/RLV6P
R_ODD4/LB1N/RLV7N
R_ODD5/LB1P/RLV7P
R_ODD2/LB2N/RLV8N
R_ODD3/LB2P/RLV8P
R_ODD0/LBCKN/LLV0N
R_ODD1/LBCKP/LLV0P
G_ODD6/LB3N/LLV1N
G_ODD7/LB3P/LLV1P
G_ODD4/LB4N/LLV2N
G_ODD5/LB4P/LLV2P
G_ODD2/LA0N/LLV3N
G_ODD3/LA0P/LLV3P
G_ODD0/LA1N/LLV4N
G_ODD1/LA1P/LLV4P
B_ODD6/LA2N/LLV5N
B_ODD7/LA2P/LLV5P
B_ODD4/LACKN/LLV6N
B_ODD5/LACKP/LLV6P
B_ODD2/LA3N/LLV7N
B_ODD3/LA3P/LLV7P
B_ODD0/LA4N/LLV8N
B_ODD1/LA4P/LLV8P
R10
T12
U12
T13
U13
T21
T20
T19
U20
U19
V20
V21
V19
W21
W20
Y21
Y20
AA20
Y19
AA19
W19
AA18
Y18
W18
Y17
W17
Y16
AA16
W16
MVREF
0RX4
0RX4
RP46
TESTPIN
USB_DETEC1
PWM1
PWM0
1K 1K
R41 R37
SPI_CSN_1
SP_SDO
WPN
1
2
3
4
2
CE#
VDD
SO
HOLD#
WP#
SCK
VSS
SI
U66
8
7
6
5
VCC-FLASH
SPI_SCK
SPI_SDI
C557
10uF
51R/0805
51R/0805
+3.3V_SB
Vpp
330mv
C555 C399
22uF 0.1uF
+1.8V
C400
0.1uF
DDR2 Power
R22
10K
Vpp
140mv
Vpp
140mv
C354
0.1uF
C353
0.1uF
C379
0.1uF
0R/0603
1
2
3
4
5
6
7
8
9
10
J12
NC/10p,2.0
1
2
3
4
5
6
7
8
9
10
SAR0
SAR1
KS0
KS1
C345
0.1uF
4.7K
R183
Vpp
150mv
C328
0.1uF
VDDC
C329
0.01uF
R556
R558
AUOUTL1
AUOUTR1
SHEET:
CHECKED:
DESIGN:George Guo
1
C86
10uF
KS0
KS1
APPRD:
VER:1.0
Date: Feb. 3,2010
LED_G
R179
2K
Q16
3904
+5VSB
4 OF 9
IRIN
AOUT_R1
AOUT_L1
AMP_RIN0
AMP_LIN0
3p,2.0,Keypad
1
2
3
J7
IRIN
+5VSB
10nF 22K
C532 R559
100R
R159 0R
R181 4.7K
SAR0
MODEL: MSAV3207-K3
Q18
3904
LED_R
0R
+5VSB
0R
R189
10K
R178
R176
LED_G
LED_R
100R
10nF 22K
C530 R555
100R
10nF 22K
C529 R553
100R
R557
C531
10nF 22K
R165 22R
R554
AUOUTR0
R164
4.7K
R552
AUOUTL0
Place close to MSD318
C330
10UF
VDDC 1.2V_MAIN
1
AUDIO_OUT
KEY_STB
C95
100pF
R177
5.1K
TITLE: MSD318
LED_CTL
C93
100pF
R182
5.1K
+3.3V_SB
J6
6p,2.0,FrontPanel
1 1
2 2
3 3
4 4
5 5
6 6
C377
NC/0.1uF
2.5V_MAINCHIP
C534
0.1uF
AVDD2P5_PGA
NC/0.1uF
C336
VDDP AVDD_MEMPLL
AVSS_PGA
0R/0603
NC/0.1uF
C42
+3.3V_SB
R212
R215
1uF
C524
KEY PAD
+2.5V
L6 FB220/100mA
Vpp
250mv
+1.8V
B_MDDR_VREF
R15
10K
MSTIC_POWER_MAIN
+3.3V
C556
47uF
USB_DETEC1
ON_USB1
R6_RXO0R7_RXO0+
R4_RXO1R5_RXO1+
R2_RXO2R3_RXO2+
R0_RXOCR1_RXOC+
G6_RXO3G7_RXO3+
G4_RXO4G5_RXO4+
G2_RXE0G3_RXE0+
G0_RXE1G1_RXE1+
B6_RXE2B7_RXE2+
B4_RXECB5_RXEC+
B2_RXE3B3_RXE3+
B0_RXE4B1_RXE4+
R355
R354
All Config Pin should be LOW
when SYSTEM power on
I2S_OUT_BCK
I2S_OUT_MCK
I2S_OUT_SD
1K 1K
1K
R44 R43 R45 R42
NC/1K
+3.3V
0RX4
0RX4
0RX4
0RX4
RP45
RP44
RP43
RP42
RP41
B_MDDR_VREF
MIUA_DQ0
MIUA_DQ1
MIUA_DQ2
MIUA_DQ3
MIUA_DQ4
MIUA_DQ5
MIUA_DQ6
MIUA_DQ7
MIUA_DQ8
MIUA_DQ9
MIUA_DQ10
MIUA_DQ11
MIUA_DQ12
MIUA_DQ13
MIUA_DQ14
MIUA_DQ15
MIUA_DQS1
MIUA_DQSB1
MIUA_DQS0
MIUA_DQSB0
MIUA_DQM1
MIUA_DQM0
MIUA_A0
MIUA_A1
MIUA_A2
MIUA_A3
MIUA_A4
MIUA_A5
MIUA_A6
MIUA_A7
MIUA_A8
MIUA_A9
MIUA_A10
MIUA_A11
MIUA_A12
MIUA_A13
MIUA_BA0
MIUA_BA1
MIUA_BA2
MIUA_CASZ
MIUA_RASZ
MIUA_MCKE
MIUA_MCLK
MIUA_MCLKZ
MIUA_WEZ
MIUA_ODT
ON_USB1
J17
C13
A20
A12
B20
B21
B12
B19
A13
B14
A18
C14
A19
C19
B13
B18
C15
C16
A15
B16
A16
C18
B17
A9
E20
B9
F21
C9
F20
B8
G21
C8
G19
F19
B7
G20
A7
D20
D21
E19
C10
A10
D19
B11
C11
C21
B10
IC Configuration Selection
MSD318-ATSC
GPIO
LVDS
MSD318-ATSC
U11B
DDR2 16bit
2
PAD_IO[14](A-DQ0)
PAD_IO[32](A-DQ1)
PAD_IO[15](A-DQ2)
PAD_IO[33](A-DQ3)
PAD_IO[34](A-DQ4)
PAD_IO[13](A-DQ5)
PAD_IO[31](A-DQ6)
PAD_IO[17](A-DQ7)
PAD_IO[18](A-DQ8)
PAD_IO[29](A-DQ9)
PAD_IO[19](A-DQ10)
PAD_IO[30](A-DQ11)
PAD_IO[28](A-DQ12)
PAD_IO[16](A-DQ13)
PAD_IO[27](A-DQ14)
PAD_IO[20](A-DQ15)
PAD_IO[21](A-UDQSP)
PAD_IO[22](A-UDQSM)
PAD_IO[23](A-LDQSP)
PAD_IO[24](A-LDQSM)
PAD_IO[25](A-UDQM)
PAD_IO[26](A-LDQM)
PAD_IO[8](A-AD0)
PAD_IO[41](A-AD1)
PAD_IO[5](A-AD2)
PAD_IO[44](A-AD3)
PAD_IO[3](A-AD4)
PAD_IO[43](A-AD5)
PAD_IO[6](A-AD6)
PAD_IO[45](A-AD7)
PAD_IO[4](A-AD8)
PAD_IO[46](A-AD9)
PAD_IO[42](A-AD10)
PAD_IO[2](A-AD11)
PAD_IO[35](A-AD12)
PAD_IO[0](A-AD13)
PAD_IO[39](A-BA0)
PAD_IO[38](A-BA1)
PAD_IO[40](A-BA2)
PAD_IO[7](A-CAS)
PAD_IO[9](A-RAS)
PAD_IO[37](A-CKE)
PAD_IO[12](A-CLK+)
PAD_IO[10](A-CLK-)
PAD_IO[36](A-WEZ)
PAD_IO[11](A-ODT)
U11A
7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1
GPIO PULL-UP
8 6 4 2 8 6 4 2 8 6 4 2 8 6 4 2 8 6 4 2 8 6 4 2
2
2
2
2
2
2
2
5
C558
RINRIN+
GINGIN+
BINBIN+
VGA_HSYNC0
VGA_VSYNC0
0.1uF
RINRIN+
GINGIN+
BINBIN+
VGA_HSYNC0
VGA_VSYNC0
C89
2
2
2
2
2
2
2
2
3
1
SPI-SCK
SPI-SDI
SPI-SDO
SPI-CS0N
SPI_SCK
SPI_SDI
SP_SDO
SPI_CSN_1
22pF
RGB Block
R444NC/10K
R445NC/10K
24
23
22
21
SOP8-VCC
SOP8-HOLD
SOP8-CLK
SOP8-DI
SOP8-CS
SOP8-DO
SOP8-WP/Vpp
VSS
17
18
19
20
2K
R180
- 31 -
10K
A
B
C
D
NC
E54
NC
E53
NC
NC
- 32 -
5
NC
E55
DIP-20(2*10)
1 1
3 3
5 5
7 7
9 9
11 11
13 13
15 15
17 17
19 19
NC
E69
NC
E68
NC
E67
NC
E66
NC
E65
NC
E64
NC
E63
NC
E62
NC
E61
NC
E60
NC
E78
NC
E79
NC
4
SCL_2
SDA_2
NC
2
4
6
8
10
12
14
16
18
20
NC
E56
CN1
2
4
6
8
HDMI_CEC
10
12
HDMI2/5V
14
16
HOTPLUG_2# 18
20
NC
E57
SIDE HDMI CONNECTOR
E52
HDMI1/5V
HOTPLUG_1#
SCL_1
SDA_1
HDMI_CEC
NC
E58
A
B
20
GND1
21
GND2
22
GND3 DATA0 SHIELD
DATA023
CLK+
GND4
CLK SHIELD
CLKCEC
NC
SCL
SDA
DDC/CEC GND
+5V POWER
HOT PLUG
HDMI
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
E46
DATA2+
DATA2 SHIELD
DATA2DATA1+
DATA1 SHIELD
DAT1ADATA0+
NC
CN3
E47
HDMI0/5V
HOTPLUG_0#
E39
SCL_0
SDA_0
HDMI_CEC
NC
C
D
DATA2+
DATA2 SHIELD
DATA2DATA1+
DATA1 SHIELD
DAT1ADATA0+
20
GND1
21
GND2
22
GND3 DATA0 SHIELD
DATA023
CLK+
GND4
CLK SHIELD
CLKCEC
NC
SCL
SDA
DDC/CEC GND
+5V POWER
HOT PLUG
HDMI
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
4
HDMI2-RX2P
HDMI2-RX2N
HDMI2-RX1P
HDMI2-RX1N
HDMI2-RX0P
HDMI2-RX0N
HDMI2-CLKP
HDMI2-CLKN
HDMI_CEC
SCL_1
SDA_1
HOTPLUG_1#
HDMI1-RX2P
HDMI1-RX2N
HDM1-RX1P
HDMI1-RX1N
HDMI1-RX0P
HDMI1-RX0N
HDMI1-RXCP
HDMI1-RXCN
HDMI_CEC
SCL_0
SDA_0
HOTPLUG_0#
NC
NC
NC
NC
2
2
2
2
2
2
2
2
E74
E75
E76
E77
NC
NC
NC
NC
2
2
2
2
2
2
2
2
HDMI0-RX2P
HDMI0-RX2N
HDMI0-RX1P
HDMI0-RX1N
HDMI0-RX0P
HDMI0-RX0N
HDMI0-CLKP
HDMI0-CLKN
HDMI1-RX2P
HDMI1-RX2N
HDMI1-RX1P
HDMI1-RX1N
HDMI1-RX0P
HDMI1-RX0N
HDMI1-CLKP
HDMI1-CLKN
E70
E71
E73
E72
HDMI0-RX2P
HDMI0-RX2N
HDMI0-RX1P
HDMI0-RX1N
HDMI0-RX0P
HDMI0-RX0N
HDMI0-CLKP
HDMI0-CLKN
3
3
4
4
4
4
4
4
4
4
R311
R330
R312
R331
SCL_1
SDA_1
SCL_2
SDA_2
HDMI_CEC
3
R342
NC/0R
Q301
NC/2N7002
2
22K
100R HDMI2-SCL
100R HDMI2-SDA
100R HDMI1-SCL
100R HDMI1-SDA
1
APPRD:
CHECKED:
2
VER:1.0
SHEET:
DESIGN:George Guo
3 OF 9
Q303
3904
HOTPLUG_2#
R316
1K
HDMI2/5V
MODEL: MSAV3207-K3
2
Q304
3904
HOTPLUG_1#
R334
1K
HDMI1/5V
Date: Feb. 3,2010
HDMI-CEC
2
2
2
2
R339 1
1K
R353
10K
R340 1
1K
Q305
3904
HOTPLUG_0#
R338
1K
HDMI0/5V
1
TITLE: HDMI IF
R327
NC/27K
R332
NC/100R HDMI-CEC
HDMI2-SCL
HDMI2-SDA
HDMI1-SCL
HDMI1-SDA
2
2
HDMI2-HPDIN
HDMI1-HPDIN
R352
10K
R343 1
1K
R351
10K
HOTPLUG
HDMI0-HPDIN
HDMI0-SCL
HDMI0-SDA
2 HDMI2-HPDIN
SCL_2
SDA_2
2 HDMI1-HPDIN
SCL_1
SDA_1
100R HDMI0-SCL
100R HDMI0-SDA
+5VSB +3.3V_SB
R310
R301
SCL_0
SDA_0
R317
SCL_0
SDA_0
2 HDMI0-HPDIN
22K
22K
22K
22K
22K
R315
HDMI2/5V
R335
R314
HDMI1/5V
R337
R319
HDMI0/5V
2
3
2
CN2
E40
3
5
NC
E48
E59
1
E49
2
NC
3
NC
E50
2
E51
A
B
C
D
- 33 -
+
SPDIF_OUT
0.1uF
C33
1K
R31
R29
220R
C34
0.1uF
3906
Q7
1
+5V
SCART1_VOUT
AGND
Scart1_Lout
AGND
Scart1_Rout
R134
220R
R32
150R
R27
150R
1uF
C29
R131
10K
C68
10uF
CVBS_OUT
C37
33pF
SPDIFOUT
FB_11_OHM_500MA
L2
Gain=Rf/Rg
Rg
R133
75R
1
R95
75R
R93
NC
CN6
12K
4
6
5
4
3
2
1
6
5
4
3
2
1
R102
10K
OUTPUT
1
2
J4
C28
47nF
47nF
VCOM0
REAR_AV
C489 47nF
C501 47nF
C490 47nF
C502 47nF
R542 33R
R543 68R
R544 33R
Q8
3904
R100
100R
+8V
PH_DETECT
R109
47R
1
R99
4.7k
SIDE_CVBS
SIDE-AU-L
+8V
R91
47R
R110
10K
47k
E14
4.7uF
C200
R357
R92
10K
R104
+3.3V
100K
C58
1uF
R86
4.7k
33R
4
4
4
4
4
4
4
R358
R356
100K
3
LINE_IN_2L
LINE_IN_2R
HP_DET
AOUT_L1
SIDE_AV
100R
AOUT_R1
C56
1uF
47nF
2.2uF
R108
12K
22K C59
C27
2.2uF
R136
12K
22K C55
YPbPr_RIN-
YPbPr_RIN+
YPbPr_BIN-
YPbPr_BIN+
YPbPr_GIN-
YPbPr_GIN+
YPbPr_SOG
R105
R112
R118
75R
R85
47k
R333
4.7k
1
R79
4.7k
R106
Q5
3904
R80
100R
13pin 1.25mm
1
2
3
4
5
6
7
8
9
10
11
12
13
J8
PH_R
Location
Near RCA.
R87
10K
C53
2.2uF
SIDE-AU-R
SIDE-AU-L
SIDE_CVBS
PH_L
YPbPr_RIN-
YPbPr_RIN+
YPbPr_BIN-
YPbPr_BIN+
YPbPr_GIN-
YPbPr_GIN+
YPbPr_SOG
HP_DET
SIDE-AU-R
C491 47nF
C488 47nF
R545 68R
C492 1nF
4
VCOM0
R541 68R
4
REAR_AV
R540 33R
4
LINE_IN_0L
R539 0R
Closed to MST IC
C57
2.2uF
E27
NC/V800AA
1
2
E35
NC/V800AA
68R
C26
Closed to MST IC
R94
Scart1_Lout
Scart1_Rout
CVBS_OUT
12K
33R
LINE_IN_0L
4
LINE_IN_0R
3
4
4
VGA IN
CN12
VGA
DDC_SCL_D
DDC_SDA_D
1
2
3
4
5
6
7
CON4
J5
DVD POWER
4
3
2
1
7pin 2.0mm
J3
+5V
DVD_CVBS
DVD_AR
DVD_AL
DVD INPUT
1
4
5
2
3
6
VGA Audio IN
CN11
R147
100R
R146
100R
R149 R148
10K
10K
15
14
13
12
11
1
6
2
7
3
8
4
9
5
10
2
2
R78
22R
C35
100R
100R
R71
NC
+3.3V_SB
47R
R74
150R
R67
75R
R69
R68
R76
22K
R210
DVD_AV
IRIN
DVD_ON/OFF
47nF
DVD-Rin
DVD-Lin
12K 12K
R213R214
22K
4
VGA_VSYNC0
R211
4
VGA_HSYNC0
NC
5
SPDIF_OUT
SPDIF Output
5
4
3
2
1
5p,2.0 AV OUT
CN7
㢹AVৠ
ৠℹ᳝༅ⳳˈⷁ᥹EC4
2Vp-p
Q10
3904
R135
22K
NC
EC4 220uF/16V
Rf
R120
220R
E10
E41
NC/V800AA
1
+5V
E9
Q11
3906
HD_Pr
HD_Pb
HD_Y
R111
2.2uF
LINE_IN_0R
NC
C666
33pF
SIDE_Pr
SIDE_Pb
SIDE_Y
HD_Pr
REAR_CVBS
HD_Pb
HD_Y
R77
C54
22K
2.2uF
E7
R130 75R
C67
0.1uF
7
5
6
8
3
4
REAR_CVBS
R82
REAR_AUDIO_L
C52
22K
NC
A
B
R889 NC/0R
6
5
4
3
2
1
7
5
6
8
3
4
9
R81
REAR_AUDIO_R
E6
SCART1_VOUT
6
5
4
3
2
1
V
R
9
REAR_AUDIO_L
REAR_AUDIO_R
4
E5
AV Output
NC
CN5
AV-JACK-1
Pr
Pb
L
1
2
NC
C
D
Y
1
2
R132
75R
CN4
5
R345
R88
75R
R90
75R
16
17
YPbPr & AV IN
E24
8
NC
7
NC
E25
8
E26
7
R346
NC
R347
E8
NC
2
NC
3
NC
3
E3
2
NC
2
E16
3
NC
NC
E4
NC
NC
NC
NC
E1
8
E2
7
C70
C518 LINE_IN_1L
1
APPRD:
Date: Feb. 3,2010
VER:1.0
9
CHECKED:
4
4
4
4
SHEET:
OF
4
4
4
DESIGN:George Guo
2
DVD_IN_R
DVD_IN_L
4
4
BIN-
GIN-
RIN-
BIN+
GIN+ 4
RIN+
MODEL: MSAV3207-K3
IRIN
DVD_IN_R
DVD_IN_L
Closed to MST IC
C533 2.2UF
C528 2.2UF
DVD_ON/OFF
12K
R70
LINE_IN_1L
Closed to MST IC
VGA_LIN 2.2UF
LINE_IN_1R
UART-TX 4
UART-RX 4
C517 LINE_IN_1R
100R
100R
2.2UF
R58
R62
47nF
47nF
47nF
47nF
47nF
47nF
Closed to MST IC
C497
C487
R549 68R
R551 68R
C485
R547 68R
C496
R550 33R
R-
C486
R548 33R
GB-
C495
R546 33R
1
TITLE: YPBPR VGA AV IN/OUT
12K
R63
DDC_SDA_D
DDC_SCL_D
VGA_RIN
560pF 560pF
C69
NC
8
75R
E11
7
NC
3
R143
2
75R
E12
3
R144
2
NC
8
75R
E13
7
R145
E15
NC
A
B
C
D
A
R208
R207
+
+
10uF
C174
+5V
R303
5.6K
R325
100K
5
4
8
7
6
2
AGND
SS
EN
COMP
VCC
U17
MP1482
+5VSB
Q2
3904
H:ON
L:OFF
POWER-ON/OFF
EC2
470uF/25V
EC3
220uF/16V
FB
SW
BS
CN9
2
3
1
2
3
1
POWERJACK
5
3
R286
10nF
R287
1 C154
4.7K
1.8K
15H_2A
1.02A
1.27V
L1
1
R18
+
Q3
1
R3
1K
1
2
3
4
NC/CON4
J20
R17
R16
4.7K
NC
1
2
3
4
H:ON
L:OFF
PW_ON/OFF 4
CON4
H3
C168
4
NC/0.1uF 0.1uF
C165
VDDC
1.28V 826mA (1080P)
3904
4.7K
5.08V 61mA
R4
1K
+5VSB
DC12V
Adapter connector,For LED
4
11.89V 208mA (1080P/MUTE)
EC1
470uF/16V
+12V
CCFL: Mount R207,R208
LED : Mount R206,R209
NC
0R
0R
NC
FB42R/4A
FB2
+
+1.2V FOR MST CORE
BL-ON/OFF R209
C175 3.3nF
B
J15
BL-ADJUST R206
C166 0.1uF
C
13
12
11
10
9
8
7
6
5
4
3
2
1
MAINPOWER
FB42R/4A
FB1
+5V
5.05V 1.32A (1080P)
1
2
D
C173 0.1uF
3
2
1
2
1
2
3
2
+5V
+5V
C19
0.1uF
D40
1N4001
C289
0.1uF
+5V
3
C21
0.1uF
3
NEW
VIN
3
3
NEW
2
0.1uF
R33
+
220uF/16V
EC18
R34
220R
0.1uF
10uF
0R/0805
+2.5V
Vpp:150mV
+1.8V
5_14 MODIFY
220uF/16V
FB42R/4A
EC19
FB10
BLK_ON
2
R302
3904
1
C7
Add
NC/10K
CCFL: Add J16
LED : Delete J16
+
EC23
Vpp
150mv
APPRD:
CHECKED:
1
VER:1.0
SHEET:
1 OF 9
220uF/16V
+3.3V_SB
+3.3V_SB
DESIGN:George Guo
0.1uF
C163
0.1uF
3.29V 76mA (1080P)
Modify
2.2uF
J16
5p,2.0,inverter
10K
1 1
BL-ON/OFF 2
BL-ADJUST 3 2
3
4 4
5 5
R999
MODEL: MSAV3207-K3
0.1uF
C2
+5VSB
NC
BL-ON/OFF
100R BL-ADJUST
C164
+5V
R296
Date: Feb. 3,2010
0R
R5
NC
R2
Q36 R294
NC/4.7K
4.7K
R295
+3.3V
R291
1
TITLE: POWER
820R
510R
4.7K
R297
Q37
3904
U2
AMS1117-3.3
4.7K1
R293
4.7K
R298
+5V
Inverter Connector
BRI_ADJ-PWM3
2
Vpp:230mV
1.81V 256mA (1080P)
5_14 MODIFY
0.1uF
C23
R349
U10
470R
AMS1117-ADJ
C998
220uF/16V
Vpp:220mV
2.52V 183mA (1080P)
0.1uF
C22 +
C24 +
2
220R
R25
220R
0R
R19
NC
R20
FB42R/4A
EC17
FB7
+3.3V
3.29V 29mA (1080P)
R35
VOUT
U6
AMS1117-ADJ
2
U3
AMS1117-3.3
VOUT
VOUT
C999
VIN
VIN
3
4
TAB
1
1
2
POWER INPUT
470uF/16V
C171
C167
10uF
4
TAB
ADJ
1
1
3
2
5
C169 0.1uF
1
2
3
2
2
4
3
ADJ
4
TAB
ADJ
1
1
2
- 34 -
1
ADJ
2
IN
OUT
A
B
C
D
7-2 .Wiring Connection Diagram
1
2
5 7
6
NO.N ame
Connection Wire(For Speaker)
1
Connection Wire(Power For Mainboard)
2
LVDS Wire
3
Connection Wire(For Keyboard and Remote)
4
Connection Wire(Control for Backlight on/off)
5
6
Connection Wire(Control for DVD POWER)
Connection Wire(Control for DVD)
7
- 35 -
3
4
8. TV Operation
1. PICTURE MENU
The first item of the MENU is the PICTURE MENU.
This menu provides several video adjustment options
for fine tuning the video display.
Press
to select, press
to adjust, press MENU
to exit.
1). Picture Mode: Select the user picture mode (Standard,
Sports, Movie, Custom, Vivid).
2). Brightness: This will adjust the light output of the
complete picture. This will mainly affect the darker
areas of the picture.
3). Contrast: This will adjust the intensity of bright parts
in the picture but keep the dark parts unchanged.
4). Color: This will adjust the saturation level of the
colors to suit your personal preference.
5). Tint: Allows you to select color mix (tint) of the
picture.
6). Sharpness: This will adjust sharpness of fine details
in the picture.
<
Picture Mode
2. AUDIO menu
The second item of the MENU is the AUDIO MENU.
You can adjust sound options here.
Press
to select, press
to adjust, press MENU
to exit.
1). Sound Mode: Select the user sound mode (Standard, News,
Music, Theater, Sports, Custom).
2). Bass: Adjust to increase or decrease lower-pitched sounds.
3). Treble: Adjust to increase or decrease higher-pitched sounds.
4). Balance: Adjust to emphasize left or right speaker balance.
5). Surround: Turn on or off the simulated surround sound
feature.
6). AVL: Auto Volume Leveler, This will reduce the differences in
volume level during commercials or when changing the channel.
7). Digital Output: Select the digital sound signal that will be
output from the coaxial audio output.
8). Audio Language: Select the audio language (English,
French, Spanish).
Sound Mode
Bass
Treble
Balance
Surround
AVL
Digital Output
>
Standard
Contrast
50
Brightness
50
Color
50
Tint
0
Sharpness
50
Audio Language
>
Advanced Video
Adjust
Menu
Select
Adjust
Exit
Note:
If you want to adjust contrast, brightness, color,
and sharpness, the picture mode must be set to
"Custom". Standard mode is the default setting, if you
select other options, the power consumption may
change.
Advanced Video:
Press
to select Advanced Video, press , and
the screen shown below will be displayed.
Aspect
Noise Reduction
Adjust
<
<
<
Select
Normal
Wide
Middle
Menu
>
>
>
>
Standard
50
50
0
<
<
<
<
>
>
>
>
Off
Off
PCM
English
Select
Menu
Exit
Note:
The Audio language option is only available for ATSC (DTV)
programs.
3. SETUP MENU
The third item of the MENU is the SETUP MENU.
You can set system settings here.
Press
to select, press
to adjust, press MENU to exit.
1). Color Temp: This will increase or decrease Warm (red)
and Cool (blue) colors to suit your personal preference.
Select Cool to give the white colors a blue tint, Normal
to give the white colors a neutral tint, Warm to give the
white colors a red tint.
2). Aspect: This will vary the size of the image on the TV
screen. There are four modes which can be selected
(Wide, Zoom, Cinema and Normal).
3). Noise Reduction: Adjust to reduce the appearance of
noise in the picture (dots). There are five modes to
choose from (Strong, Auto, Off, Weak and Middle).
Color Temp.
<
>
>
>
>
>
>
Parental Controls
Timer
Closed Caption
Menu Settings
VGA Settings
Restore Default
Adjust
Select
Menu
Exit
Note:
Restore Default: Reset all settings to the factory
default value.
Channel names that have been changed through the option
in the Channel Menu are not reset when a restore default is
initiated.
Exit
- 36 -
OPERATION
3.1. Parental Controls:
Press
to select Parental Controls , press
screen shown below will be displayed.
, and the
1): TV: Press , and the screen shown below will be
displayed.
ALL
Enter Password
FV
----
V
S
L
D
Adjust
Adjust
Menu
Select
Menu
Select
Exit
Exit
Content
Input the password, and you will enter the Parental
Control menu. The factory default password is 0000.
Rating
FV
V
L
D
S
(Fantasy (Violence) (Sexual
(Adult
(Sexually
violence)
situation) language) suggestive
dialog)
Content
TV-Y (All
children)
TV-Y7(Direct to
<
<
<
<
<
P.G switch
US
Canada
RRT setting
Reset RRT
Adjust
Off
Menu
Select
Suggested order children)
TV-G(General
age
>
>
>
>
>
>
Change password
audience)
Exit
TV-PG(Parental
Guidance
suggested)
X
X
X
X
TV-14(Parents
strongly
cautioned)
X
X
X
X
TV-MA(Mature
audience only)
X
X
X
Press the ENTER key to lock/unlock Parental Controls .
Change Password:
Press
, and the screen shown below will be
displayed.
2). MPAA: switch the movie-rating control level: N/A,
G, PG, PG-13, R, NC-17, X.
Rating
Description
G
----------
Old password
New password
Confirm password
General audiences, All Ages admitted
Parental Guidance suggested. Some material may not be
Suitable for children.
PG
Age PG-13
Menu
Select
NC-17
Exit
1). Old password: Input the old password
2). New password: Input the new password
3). Confirm password: Input the new password again
X
Parents strongly cautioned. Some material .may be
Inappropriate for children under 13.
Restrict. Under 17 requires accompanying parent or adult
guardian (age varies in some jurisdictions).
R
Adjust
X
No one 17 and under admitted.
X is an older rating that is unified with NC-17 but may be
encoded in the data of older movies.
Canada: Press
displayed.
, and the screen shown below will be
P.G switch:
When the Parental Control is ON, the options shown
below can be adjusted.
US: Press , and the screen shown below will be displayed.
Canada English
Canada French
TV
<
MPAA
N/A
<
<
EXEMPT
EXEMPT
>
>
>
>
Adjust
Select
Menu
Exit
1): Canada English: switch the English-rating control level:
EXEMPT, C, C8+, G, PG, 14+, 18+.
Adjust
Select
Menu
Exit
- 37 -
OPERATION
Description
Rating
E
C
Exempt: Includes news, sports, documents and other information
programming: talk shows, music videos, and variety programming.
Children: Intended for younger children under the age of 8 years.
Pays careful attention to themes that could threaten their sense of
securityand well-being.
C8+
Children over 8 years old: Contains no portrayal of violence as the
preferred, acceptable, or only way to resolve conflict; nor encourage
children to imitate dangerous acts which they may see on the screen .
G
General: Considered acceptable for all age groups, Appropriate
viewing for the entire family, contains very little violence, physical,
verbal or emotional.
Parental Guidance: Intended for a general audience, but may not be
suitable for younger children (under the age of 8) because it could
contain controversial themes or issues.
Age PG
14+
Over 14 Years: Could contain themes where violence is one of the
dominant elements of the storyline, but it must be integral to the
development of plot or character. Language usage could be profane
and nudity, present within the context of the theme.
18+
Adults: Intended for viewers 18 years and older and might contain
depictions of violence, which while related to the development of
plot, character or themes, are intended for adult viewing. Could
contain graphic language and portrayals of nudity.
3.2 Timer
You can adjust the sleep timer and time related settings here.
Press
to select, press
to adjust, press MENU
to exit.
Sleep timer
Time zone
DST
<
<
<
Clock
>
>
>
Off
Pacific
Off
1999/12/31 04:03PM
Adjust
Select
Menu
Exit
Sleep Timer: You can set the sleep timer.
Note:
Time zone, DST and Clock are available in ATSC mode ,
and the Clock can't be adjust ed .
2).Canada French: switch the French-rating control
level: E, G,8ANS+,13 ANS+,16ANS+,18ANS+.
3.3 Closed Caption: switch the closed caption mode.
Rating
Press
to select Closed Caption, press
screen shown below will be displayed.
Description
E
Exempt programming
G
General: All ages and children, contains minimal direct violence,
but may be integrated into the plot in a humorous or unrealistic
manner .
8ans+
General but inadvisable for young children: May be viewed by a
wide public audience, but could contain scenes disturbing to
children under 8 who cannot distinguish between imaginary and
real situations. Recommended for viewing with paren tal guidance .
13ans+
Over 13 years: Could contain scenes of frequent violent scenes
and intense violence.
Age
CC Mode
Basic Selection
Advanced Selection
<
<
<
, and the
>
>
>
>
Off
CC1
Service 1
Option
16ans+ Over 16 years: Could contain frequent violent scenes and violence.
18ans+ Over 18 years: Only for adult viewing. Could contain frequent
violent scenes and extreme violence.
RRT setting: in ATSC digital TV mode, this option
could can be adjusted
Reset RRT: Press
displayed.
, and the screen shown below will be
Adjust
Font style
Font size
Font Edge style
Are you sure?
Font Edge color
FG color
BG color
FG opacity
YES
BG opacity
Press ENTER Key To Select
Adjust
Adjust
Select
Menu
Menu
Exit
1): Advanced selection: only available in ATSC mode.
2): Option: You can edit the closed caption options.
Press , and the screen shown below will be displayed.
Mode
NO
Select
<
<
<
<
<
<
<
<
Select
Default
Default
Default
Default
Default
Default
Default
Default
Menu
Exit
NOTE: Only available in ATSC mode.
- 38 -
>
>
>
>
>
>
>
>
Custom
Exit
OPERATION
3.4 Menu Settings
You can adjust Menu Settings here.
Press
to select, press
to adjust, press MENU
to exit.
Menu Language
<
1). Air/Cable: Select Air TV signal or Cable TV signal.
2). Auto Scan: If it's the first time using the TV, you
should perform a full channel scan in order to capture
and store all available channels.
Press the to confirm, and the screen shown below
will be displayed.
>
English
Are you sure?
YES
NO
Adjust
Select
Menu
Exit
Press ENTER Key To Select
3.5 VGA Settings: Only available in VGA (PC input)
mode.
Press
to select VGA Settings, press
shown below will be displayed.
Adjust
, and the screen
H-pos
50
V-pos
50
Clock
50
RF CH:
Found:
Analog:
Digital:
>
Auto
Adjust
Select
Menu
Adjust
4. Channel MENU
Here you add/skip TV channels and customize displayed
channel info.
Press
to select, press
to adjust.
<
Air
<
2-1
Favorite
Show/Hide
Channel Lable.
DTV signal:
Adjust
Good
Select
Menu
Select
Menu
Exit
3). Favorite: Press ENTER to add/delete favorite channels.
4). Show/Hide: Press the ENTER button to display or
hide channels.
5). Channel NO. : Display the current channel number.
Press
to change the channel.
6). Channel label: Press
and
to edit the current
channel name.
7). DTV signal: Display DTV signal strength.
Signal strength indicator is for reference only, it
cannot be selected or adjusted.
>
>
>
>
>
>
Auto Scan
Channel NO.
4
4
1
3
Exit
1). H-Pos: Adjust the horizontal position of the screen.
2). V-Pos: Adjust the vertical position of the screen.
3). Clock: Fine tune the screen width.
4). Phase: Fine tune the phase of the screen. Usually
you don't need to adjust this item option .
5). Auto: Auto adjust to fit the screen.
Air/cable
Exit
Select "YES" and press the ENTER to confirm,
and the screen shown below will be displayed,
which indicates that the auto search is progressing.
50
Phase
Menu
Select
Exit
- 39 -
OPERATION
5. Multimedia MENU
: play
With an external storage device attached to the USB input,
you can use the Multimedia Menu to display JPEG pictures
and play MP3 music.
: pause
: stop
Before starting operation, verify that the USB storage device
is using the FAT32 file system format. This television does
not support NTFS or other formats. Please use a high-speed
USB 2.0 device with a maximum capacity of 50GB.
: fast backward
: previous
: next
1. Select a Photo
The screen shown below will be displayed.
: fast forward
: repeat all
USB
Photo
C:
Music
Random
C:\photo\
..
011.jpg
011.jpg
200812222178878787.jpg
20081.jpg
20087.jpg
20287.jpg
20787.jpg
20087.jpg
20787.jpg
20087.jpg
:17
001/018
Total size:3.7 GB
Unused size: 3.7 GB
1024 x 768
372.72KB
2006:07:14 15:37:42
Use
select the .jpg files or folders, press ENTER
to display the photo or open the folder, press EXIT to
stop playing or go to the previous menu.
2. Select Music
The screen shown below will be displayed.
USB
Photo
C:
Music
..
Everything I do.mp3
Everything I do.mp3
Title:
Sealed With A Kiss.mp3
.mp3
.mp3
.mp3
.mp3
.mp3
.mp3
.mp3
:17
Total size:3.7 GB
Unused size: 3.7 GB
C:\laoge\
Artist:
Album:
Year:
Bit Rate: 128kbps
Play
05:49
06:33
001/018
Random
Use
select the .mp3 files or folders, press ENTER to
play or open the folder, press EXIT to go to the previous menu.
- 40 -
: random play
8.1 How to enter into the factory model
1. You can press "source-2-5-8-0" to go into factory setting. Presse the key "exit"
to shut the factory setting.
Content:
1: ADC setting: set ADC value of YUV,VGA. It can also be auto-set. Adopt 100%
color bar to yuv and Checkerboard signal to vga.
2:Color Temp.:
3:Video Quality:
4:Sound Quality:
5:Curve Setting:
6:Aging Mode:
7:Other Setting:
8:SW Upgrade:
9:Shipment:
7KH¿UVWOLQHLV6:9HU1R
- 41 -
8.2 How to update software
Haier MSD318QT F/W upgrade with USB SOP
Step 1: Ready for F/W Upgrade
1.1 Prepare a USB memory .
&RS\WKHVRIWZDUH¿OHPHUJHIURP\RXUFRPSXWHUWRWKH86%PHPRU\DQGUHPRYHLW
from computer’s USB port!
Step 2: F/W Upgrade
2.1 AC ON
2.2,Then input USB, press POWER.
2.3 Then press "source-2-5-8-0" and choose "SW Upgrade",and then press "ENTER".
2.4,Now you should choose "Yes" and then press "ENTER" TV begin to update.You should
remove the USB memory and reset TV after update.
Note: When Upgrade on the process, please don’t Power-Off!
- 42 -
9. Trouble shooting
9-1. Simple check
- 43 -
Service Manual
Model No.:
9-2. Main board failure check
1) Black creen
Is power LCD normal?
6
5
J2
J15
2
Check Q2,Q3 and the
11
2
2) White screen
on VCC pins of J9
Check if Q31 is working
Signal on J9
Check if J9is
- 44 -
Service Manual
Model No.:
3)
Panel display abnormally
connector
- 45 -
J9
is at normal level
Service Manual
Model No.:
4) No sound
No sound
Check the
input
source
Reset
volume
N
Check if there is sound input
signal
Y
N
Y
Check if the volume control is
at 0 level or muted
N
Check the
speakers
Check if there is output at
J11
Y
N
Check if the power supply
system is damaged, short
circuit or mis-connected
N
Check if there is +12V input at
PIN 8 of U19
Y
Check the volume control
circuit from
U19
Y
Check if MUTE PIN7 of U19 is low
voltage
N
Check the volume input
circuit from U8 to
U19
N
Check if there is signal input at PIN1
& PIN12 of U19
Y
Replace U19
- 46 -
Service Manual
Model No.:
5˅TV failure
TV no channel
Fix the RF
set
N
Check if there is RF
signal input
Y
Check if there
is I2C signal
at PIN4 &
PIN7 of TUNER1
N
Check the I2C
circuit
between
U1
1 and
U24
4
Y
Check if there is
+5V at PIN2 of
U24
4
Y
Check if there is
intermediate
frequency signal
output at PIN12 of
U24
4
Check the
tuner
- 47 -
N
Y
Check the signal
circuit between
U1
1 and U24
4
Check the power
supply circuit to
this PIN2
Service Manual
Model No.:
(6) HDMI no picture or picture abnormal
HDMI no picture or picture abnormal
If CN2 is disconnected
Y
Re-solder it
N
Check if R301,R310,R319,R317,R351,
R338 are un-soldered
N
Check Q35 and the circuit around it
- 48 -
Y
Re-solder them
Service Manual
Model No.:
(7)PC no picture or picture abnormal
PC no picture or picture abnormal
Picture abnormal
NO SIGNAL
AUTO ADJUST
Check the VGA cable
N
Check the circuit from PIN14,PIN13 to U11
N
Check the RGB circuit from PIN1,PIN2,PIN3 to U11
N
Replace U11
- 49 -
Service Manual
Model No.:
(8)YPBPR,AV,SCART NO Picture or picture abnormal
YPBPR,AV,SCART
YPBPR,SCART,RGB
All NO SIGNAL
color sast
N
Check Y,PB,PR or
Check power
R,G,B input circuit
- 50 -
Failure Mode
Part
Name
White Screen
Description
Phenomena
B/L normal,
only white screen
display
Black Screen
B/L normal,
only Black screen
display
FIIcker
Crosstalk
Failure cause
Maybe caused
by surge current
and EDS
LCD
Vcom imbalance
Circuit
Abnormal Color
Abnormal Color
Only
color abormal
Capacitance
improper bring
crosstalk inside
LCD pannel
Only
color abnormal
- 51 -
1.Chip
lose action
2.IC short or
jointion bad
3.Pannel and vsc
connect bad
Part
Name
Description
Phenomena
Dot Defect
Bright dot dark dot in
pannel
Failure cause
Incoming Inspection
Standard
Bladder between Polarizer
and top glass
Polarizer Bubble
Bladder in Polarizer
Panel or
Polarlzer
Tine or rigidity arose
Polarizer Scratch Polarizer Scratch
Eyewinker inside Polarizer
F / M i n s i d e Eyewinker inside
Polarizer
Polarizer
Abnormal Display Abnormal Display
Circuit
Flashing
Bright and dark
display alternately
- 52 -
1.Chip lose action
2.IC ahort or jointiog bad
3.Pannel and vsc connect
bad
9-3. Pannel failure
Failure Mode
Part
Name
Description
V B/D
Vertical bar
V Dim
Vertal gray line
V L/D
Vertical color
line(light or dark
forever)
H B/D
Horizontal bar
H Dim
Horizontal gary
line
H L/D
Horizontal
line(light or dark
forever)
TCP
Phenomena
- 53 -
Failure cause
Block Defect :TCP cracking or cracking
Dim or L/D :TCP Sunken
:TCP lead cracking
:ACF bonding short
:Awful environment and
something electric enter
into LCD
:Mis-align between TCP and
Panel
:Panel failure
:TCP failure
Failure Mode
Part
Name
Mechanlcal
Nolse
Description
Phenomena
When
turn panel,appear
cacophony
Ripple
Connectric circle
B/L off
B/L lose action
*Connect
badness
between wire and
electrode
B/L dark
B/L brightness
darker than
normal
*Connect
badnessShort
between wire and
electrode
B/L
wire damaged
B/L
wire damaged
B/L wire open
Without backlight
B/L shut down
B/L shutdown in
sometime
F/M
F/M
inB/L ,white,balck
Rotundity
or wirelike
Operation
abnormal
or systemic noise
Operation
abnormal
or systemic noise
Short bitween
lamp housing and
wire, Because
consume power
too much
F/M in B/L unit
- 54 -
Failure cause
Caused
by Mechanica
noise of backlight
unit
Causeed by
between
mechanism and
pannel
Failure Mode
Part
Name
Light leakage
Mechanlcal or B/
L
Uniformity
Mount hole
Description
Phenomena
Brightness
at bottom of LCM
brighter
than normal
Failure cause
B/L unit badness
B/L brightness
asymmetric
Sheet in B/L unit
is uneven
Lack screw
or screw damage
*Lack screw
Screw damage
- 55 -
10. DVD OPERATION
DVD SIDE PANEL
9
Dolby Digital
32
Disc with its content side
(shiny side) facing the front
of the unit, insert vertically
into the disc tray
PLAY/PAUSE
OPEN/CLOSE
Multi-angle
MP3 files on
CD-R/CD-RW
Subtitle choices
8
Audio choices
DVD video
How to play a DVD disc
R RESTRICTED
1. Change the TV input source to "DVD" mode by pressing
the SOURCE button on the remote or
SOURCE
on the side of the TV.
2. Place the DVD disc in the slot with the content side
(shiny side) facing the front of the unit.
3. The DVD disc will automatically be loaded in to the player
and begin to play.
4. To eject the DVD disc, press the CH LIST/ button on
remote or the OPEN/CLOSE button on the side of the unit.
Caution
This DVD Player has a Class 1 laser which may
be harmful to your eyes. Do not attempt to
disassemble the cabinet or make any adjustments.
Refer all servicing to a qualified professional.
Features
Disc formats supported by this player:
- 56 -
Parental Lock
16:9
LB
TV Aspect
Ratio modes
This product incorporates copyright
protection technology that is protected
by method claims of certain
U.S.patents and other intellectual
property rights owned by Macro vision
Corporation and other rights owners.
Use of this copyright protection
technology must be authorized by
Macro vision Corporation, and is
intended for home and other limited
viewing uses only. Unless otherwise
authorized by Macro vision Corporation.
Reverse engineering or disassembly is
prohibited.
Manufactured under license from Dolby
Laboratories."Dolby" and the double-D
symbol are trademarks of Dolby
Laboratories. Confidential Unpublished
Works. 1992-1997 Dolby Laboratories, Inc.
All rights reserved.
DVD OPERATION
MENU OPERATION
Press the SETUP button on the remote control, the SETUP MENU will be
displayed. After accessing the setup menu, press
to select an item,
and press to select the SUBMENU item. Then press the ENTER/OK
button to confirm. Press to return to the previous menu. To exit the
setup, press the SETUP button again. In the SETUP MENU, you may
choose adjust any of the following options.
LANGUAGE SETUP
Select Language in the setup menu, and display the Language submenu:
SYSTEM SETUP
Aspect Ratio
Select the aspect ratio.
Notes:
The image display ratio is related to the recorded disc format. Somes
discs can not display images in the aspect ratio you choose. If you play a
disc recorded in 4:3 format on a wide screen TV, black bars will appear
on the left and right side of the screen. You must adjust the screen setting
depending on the type of the television you have.
TV System
Select the TV system.
Note: The DVD player setting should be matched to your TV set. F o r
more information on output format, refer to the instructions or your TV
set.
RATING SETUP
Select Rating in the setup menu, and display the Rating
submenu:
OSD Language
Use this item to select the desired language for the
setup menu and screen display.
Subtitle
This option provides the preset subtitle language.
Audio
Select the built-in disc dubbing language options.
Parental Control
Set the parental control feature of the player
Note : T h e password is needed to set up the Parental Control.
DVD Menu
This option provides the film's menu language
options.
Set Password
Input four digits (password), then press ENTER /Ok to confirm.
Note: If you forget your password, please use the universal password
6666 to unlock.
VIDEO SETUP
Select Video in the setup menu, and display the
Video submenu:
MISC SETUP
Select MISC in the setup menu, and display the submenu:
Use Default Settings
Reset setup data to factory default value.
- 57 -
DVD OPERATION
MP3/JPEG PLAYBACK
PICTURE CD PLAYBACK
The PICTURE CD disc has such a directory structure structure as shown
in the following picture.
The MP3 disc has a directory structure as shown picture above.
Press
to choose the root directory and then press ENTER/OK button
to enter into the sub directory. Press
to choose the desired track and
then press ENTER/OK or PLAY to enjoy the music or movie. If you
want to return to the previous menu, press
to choose the
icon and press the ENTER/OK button.
Press Direction key to choose the root
directory and then press ENTER/OK button to
enter into the sub directory. Press Direction
key to choose the desired picture and then
press ENTER/OK or PLAY to enjoy the
picture. If you want to return to the upper menu,
press Direction key to choose
the icon and
press ENTER/OK button.
Image rotation
In picture play state, press Direction key to
rotate the picture.
Filter: Select the categories of files that are displayed in the browser
list.
Repeat: Change the repeat playing mode
Mode: Select different play mode s :
Normal: Play chapters/tracks in normal order.
Shuffle: Play tracks/chapters in a random order until all tracks/chapters
have been played.
Edit Mode: Program tracks/chapters to play. When you select the mode,
press to directory and press ENTER/OK to choose the desired track.
Select Add to program. Select Program view and select Edit mode to
cancel the edit mode. Press to display the programmed tracks and
press ENTER/OK to start playback.
Program view: Display the programmed tracks.
Browser view : Display the track directory.
Add to program: Choose the track select Add to program to add the
track to the program play list.
Clear program : In the complete stop state (press the STOP button
twice), select Edit mode to enable the edit mode. Press to program
track and press ENTER/OK to cancel the desired track. Select Clear
program to delete all tracks in the program play list.
- 58 -
DVD OPERATION
Function Buttons
INSERT/EJECT
Press this button to insert/eject the disc.
SUBTITLE
Press this button to select different subtitles subtitles (This
function must be supported on the disc)
GOTO
For DVD discs, press this button to jump to a selected title
time and chapter time.For Super VCD,VCD,CD discs, press
this button to search the desired disc time and track time and
choose the desired track.
Note: During VCD playback, the PBC mode must be set to
OFF.
0-9 keys
These buttons are used to input the time, as well as title,
chapter and track numbers.When a numeric item is displayed
on the screen, press the 0-9 keys to select the desired entry,
and press ENTER/OK to confirm.
When a VCD is playing(with PBC off), press the 0-9 keys to
select a track directly.
MENU
During DVD playback, press MENU to display the disc menu
of the current title.
During VCD/SVCD playback, press MENU to control PBC
ON/OFF.
SETUP
Press this button to enter the system setting menu. Press the
button again to exit the menu.
RETURN
When a DVD/SVCD/VCD is playing, press the RETURN
button to return to the menu(PBC ON only).
DISPLAY
Press this button to show the information of the current
disc.
ENTER
Press the button to confirm your choice on the screen.
REV
During DVD, CD MP3 or VCD playback, press REV to
scan in reverse.
Press PLAY/PAUSE to resume normal playback.
FWD
During DVD, CD,MP3, or VCD playback, press FWD to
scan forward. Press PLAY/PAUSE to resume normal
playback.
PREV
During DVD, CD,MP3, or VCD playback, press PREV to
play the previous chapter, title or track.
NEXT
During DVD,CD,MP3, or VCD playback, press NEXT to
play the next chapter, title or track.
STOP
Press the button once and the player will be in the memory
stop state. Press this button twice and the player will be in
the complete stop state.
Play/Pause
Press this button to play/pause the disc.
REPEAT
Press to select between different
repeat modes — Repeat Chapter / Repeat
Title / Repeat Off（for DVD discs）,
Repeat Single/ Repeat Folder/All/ Repeat
Off(for VCD/CD/MP3 discs)
AUDIO
Changes the audio language or audio channel.
- 59 -
11.DVD TROUBLE SHOOTING
If you have any questions, please consult the troubleshooting guide below:
REMOTE NOT WORKING
NO PICTURE OR SOUND
Ensure the power button is on.
Ensure the power outlet is operational.
Ensure the batteries in the remote control are working.
Ensure the power cord is not damaged.
Point the remote control directly at the player s IR sensor.
Remove any obstacles between the remote and the IR sensor.
Ensure the power plug is connected
firmly to the outlet.
PICTURE BUT NO SOUND
Ensure the audio is not set to mute.
UNIT NOT WORKING
Ensure you have set the AUDIO settings correctly.
Turn off the power, and then turn it on again.
POOR PICTURE OR SOUND
“NO DISC”DISPLAYED
Ensure you have set the player s AUDIO
settings correctly
Ensure you have put the disc in the DVD player.
Ensure the disc is not scratched or stained.
Ensure the disc is inserted properly
(shiny side facing out).
“BAD DISC”DISPLAYED
Ensure the disc is not distorted, stained or
scratched.
Ensure the disc is not warped, damaged or deformed.
Ensure the disc is not badly stained or damaged.
Ensure the disc format is compatible with the player.
Please check whether you have tried to play a software CD. If
so, please restart the player.
- 60 -
Sincere Forever
Haier Group
Haier Industrial Park, No.1, Haier Road
266101, Qingdao, China
http://www.haier.com
Printed in China