Transcript
NCD-61K/62K User's Manual ■ Specification Power Supply AC 100 - 240V, 50/60Hz Power Consumption 11W Max. CONCH Current Value (CV) Preset Value (RS-2) OUT 1 Output Index Lamp K/P 2 Left Key RS1 RS Key Protection Index Lamp Reset CV RS2 mode Setting Activating Key Up / Down Key V1.0 ■ Parameter Display Setting 1 (Press mode to activate.) Function Discription Level Prewarning Value PS-1: (not available for NCD-61K) To set OUT1 prewarning value. For multiple comparing output types, please see Section “Output Type”. Range: 0 - 999999. Preset Value PS-2: 1 To set OUT2 value. For multiple comparing output types, please see Section “Output Type”. Range: 0 . - 999999. Aux. Power Input Frequency Input Signal Input Level Input Imedance Display Output Dimension Memory Operating Temp. 11mA @ +12V Max. 10KHz Max. (multiple levels available) Non-voltage contact or NPN pen collector input Residual voltage, Hi: 7.2V; Lo: 8.5V (approx.) 4.7KΩ 2 rows of 6-digit red LED display Relay contact(s), 3A/250V (resistive load) 48 x 48mm; Cut-out: 45 x 45mm EEPROM, lasts 10 years Min. -10 ~ +50°C Relative Humidity 35% ~ 85% Storage Temp. -25 ~ +65°C ■ Reset Press RS2 , input NPN signals at Terminal RS, or Auto Reset under Return R or C mode, and CV will load RS value. If counting mode is set as DN (Count Down), CV will load the set value PS-2 . ■ Output Modes Return N: CV ≥PS1, OUT1 ON; CV≥PS2, OUT2 ON and hold; RS resets manually. . PV PS2 OUT2 Hold Time PS-2: (tr) PV PS2 PS1 To set the hold time OUT2 when output type is set at R, C or D. Range: 00.01 -99.99 t 0 Scaling: (SCALE) ON OFF OUT1 Formula: CV = Pulse x Scale Range: 00.01 -99.99 ON OFF ON OFF O UT2 RS Decimal Place: (Pnt) To change the decimal place of CV (non-related to the accuracy of CV). Range: 0 - 5 (Preset as 0). Input Frequency Limit: (Cnt F) 2 To limit the max. Input speed of CP1 and Cp2 to fit the characteristic of different signal. Options: 20, 100, 300, 500, 2K, 10K Hz Output Type: (OUTPUT) Return C: CV ≥PS1, OUT1 ON; CV≥PS2, OUT2 ON and CV resets. OUT2 resets with OUT1 automatically after “tr Time”. Setting 2 RS2 on the panel or external PV PS2 PS1 t 0 OUT1 OUT1 OUT2 OUT2 HL Output: Upper/lower limit output. PS1 is lower-limit comparing; PS2 is upper- limit comparing. Gate: (GATE) ■ Wiring Diagram (NCD-62K) 3 0V RS CP2 CP1 PS2 6 7 PS1 Lock RS2 Key: (RS LCK) To lock RS2 key to avoid from pressed accidentally. Yes = RS2 disabled, K/P Index Lamp lit. No = RS2 activated for resetting CV manually. t 0 Parameter Protecting Level 2 (Press mode + to activate.) Function Discription Parameter Protecting Settings: (PROTECT) 0: Disables all settings of parameters. 1: PS-1 & PS-2 are adjustable. 2: Parameters from PS-1 to OUTPUT are adjustable. 3: Opens “Parameter Setting 2” for adjustment. (Preset) Note 1: To finish setting, hold mode for 2sec. It will also finish automatically after 15sec. Note 2: If the output mode (OUTPUT) is set as HH, LL, or HL, the counting mode will change into up/down counting mode(UD). 8 9 10 +12V OUT1 11 12 OUT1 OUT2 1 OUT2 Display t 0 PV To disable or activate counting when OUT2 ON. Option: Yes / No (Preset: No) ■ LL Output: Lower limit output. If PS1 & PS2 ≤ CV, OUT1 & OUT2 On;. If PS1 & PS2 ≥ CV, OUT1 & OUT2 Off. PV Level t 0 OUT2 PS2 Initial Value of Manual Return: (rs) To set the initial CV when reset. Press RS terminal. Range: 0 - 999999. (Preset: 000000) PV OUT1 HH Output: Upper limit output. If PS1 & PS2 ≥ CV, OUT1 & OUT2 On;. If PS1 & PS2 ≤ CV, OUT1 & OUT2 Off. for 5 sec. to activate.) Function Discription Display Return D: CV=PS1, OUT1 ON; CV=PS2, OUT2 ON and resets automatically after “tr Time”. PS1 PS1 ■ Parameter OUT2 PS1 OUT2 Counting Type: (Cnt In) OUT1 PS2 t t 0 PV OUT1 UD: Count up / down. The input of CP1 and Cp2 is 90° quadrature. (signals from the encoder) UP: CP1 input (count up), CP2 disabled. DN: CP1 input (count down), Cp2 disabled. PS1 PS2 0 Options of multiple types of comparing output. NCD-62K: N, R, C, D, HH, LL, HL; NCD-61K: N, R, C, D, H, L. (Hold mode Return N: CV ≥PS1, OUT1 ON. CV≥PS2, OUT2 ON and resets with OUT1 and CV automatically after “tr Time”. ■ Dimension ~ 2 3 4 5 100-240V (NCD-61K) 0V RS CP2 CP1 6 7 8 9 10 +12V 11 12 OUT2 1 ~ 2 3 4 5 AC 100 - 240V Conch Electronic Co., Ltd. Tel: 886-6-3842111 Fax: 886-3840855
