Download SATFINDER4 INTRODUCTION USER GUIDE AND CERTIFICATE

®
SATFINDER4
INTRODUCTION USER
GUIDE AND CERTIFICATE
OF GUARANTEE
CONTENTS :
General Safety...….…………………………………………..
Basic Properties….………………………………….………..
Front Panel Keys….…………………………………………..
Back Panel Details……………………………………………
Charger Adapters……………………………………….……….
Utilization of Satfinder4 …..….…………………………..……….
Satellite set-up Menu………………….….…………………….
Channel Scan Menu..…………………………….…….…
Spectrum Analysis Menu……………….………….…..…….
Automatic Diseq-C Scan…………………….……………..
Channel List……………….…………………….…………….
Satellite Identification……………………………………….……...
Settings Menu………………….…………………….……..
Memory Information Menu……….…………………….……..
Battery Information Menu………….…………………….……..
Signal Level Indicator Menu...…………………….……..
Screen Colour Settings………………….……………….……..
Troubleshooting ………………….…………………….……..
Technical Properties………………….…………………….……..
Notes...............………………...…………………….…..……
Terms of Warranty………………………………….….………….
3
4
5
5
6
7
7
8
9
11
11
12
12
13
13
13
14
15
16
17
18
SATFINDER4 User Guide ______________________________________________2
GENERAL SAFETY:
Topics to be considered:
Please strictly follow the below mentioned instructions so as to prevent damage
that can happen to you or your device.
Before cleaning your device, pull the power cord and turn it off via button of
Power on/off and clean it with dry cloth.
Do not use accessories or additional apparatus that are not recommended by
manufacturer as they may damage the device and may void the guarantee. When
moving your device, protect it against impacts and falls otherwise the device may be
damaged. Carry your device certainly in its bag and never carry it in boxes such as
toolkit and together with the equipment that may possibly damage the device; otherwise,
device will not be covered by guarantee.
Do not use your device outdoor so as to protect your device against liquid contact
during rainy and snowy weather. Liquid contact may damage your device and device is
not covered by guarantee.
Charge your device with recommended charging adapter and in-vehicle lighter
charger. The charging devices that are not fit for utilization may damage batteries
located in your device, excessive heating allows results such as explosion and you may
be damaged; thus, such situations are under responsibility of user. When using charger
adapters, pay attention to them to be 12 volt (middle +) supplied ones. Never leave the
device ON. Batteries located in device with ON position shall lose own function in
progress of time. As lifetimes of lighter charger, charger adapter and batteries may
change depending on their utilization, they are not covered by guarantee.
When connecting your device with LNB, please be careful against short circuit;
otherwise, LNB and your device may be damaged.
Service-related topics :
Do not attempt to repair your device on your own. When you open the cover of your
device, it will not be covered by guarantee. For all services related to device, keep in
contact with your seller or technical service.
SATFINDER4 User Guide ______________________________________________3
BASIC PROPERTIES:
-
Fast and Precise Navigation
Memory of 10000 Channels
6000 TP Memory
250 Satellite Memories
Spectrum Analyzer Indicator
3.5” Coloured TFT LCD Screen
Manual Frequency Change
Manual LOF Change
Protection against short circuit
Easy Lnb setting
dBm and dBuV Level Indicator
Offset deviation value
Sharp 0502 Tuner
Diseq-c Switch Support
Auto Diseqc Search
Multiswitch Support
6 Different language options
Rapid charge in 3 hours
4-hour-long Lit-_on Battery period
Long-lasting bag
10cm x 9cm x 15cm
Signal and power level
BER Level
C/N Level
Loading software and frequency from Pc via USB
Touch-sensitive Memran: Due to touch-sensitive keys in Satfinder4, allowing
opportunity for easy and rapid use.
USB Port Connection: Due to USB Port connection, you can easily update software
of your device and load frequency.
AV IN : Due to inputs of Audio and Video, camera can be easily connected.
Sharp 0502 Tuner: Due to Sharp Tuner, you can search signal both sensitively
and rapidly.
Easy Charging: You can easily charge under all circumstances due to charger
adapter and in your car due lighter charger.
3,5” TFT LCD Screen : Due to Tft LCD screen, you can see coloured image and use
both during daytime and nighttime.
Bag: Satfinder4 is more durable due to own rigid and long-lasting bag that can be
put on neck.
Automatic Satellite and Diseqc search: Due to AUTOMATIC Diseqc selection from
Menu, Satfinder4 displays the satellite that you are ON.
6 different languages: Turkish – English – Russian– German – Spanish - French
IMPORTANT : Design and properties can be renewed without notice.
SATFINDER4 User Guide ______________________________________________4
FRONT PANEL
:
LNB AND
BATTERY
WARNING
EDITING
DIRECTION AND
DIGIT KEYS
MENÜ
TV AND
RADIO
SELECTION
LEVEL
INDICATOR
ON/OFF
A/V ENTRY
SELECTION
BACK PANEL :
SATFINDER4 User Guide ______________________________________________5
AC 220 V / 12 V DC Charger Adapter:
Due to your electrical charger adapter with 12 volt of output, you
can ensure device to remain charged continuously and thanks to that, you
can use your device in environments that do not have electricity. Keep
charger adapter away from situations such as compression, impact and
overloading. Do not open it for the purpose of repair and examination.
In-vehicle lighter charger adapter:
Due to your electrical charger adapter with 12 volt of output, you
can ensure device to remain charged continuously and thanks to that, you
can use your device in environments that do not have electricity. You can
easily charge your device during your travel due to your lighter charger
adapter in car. Keep lighter charger adapter away from situations such as
compression, impact and overloading. Do not open it for the purpose of
repair and examination.
USB Cable:
You can load software, frequency changes and various updates to
your Satfinder4 device over computer via USB cable.
SATFINDER4 User Guide ______________________________________________6
UTILIZATION OF SATFINDER4
Please turn on your SATFINDER4 device by button of POWER ON/OFF.
TV/Radio channel list will display on TV broadcast Screen via OK key.
SATELLITE SEARCH MENU :
When pressing MENU key, MAIN MENU is displayed on the screen and by
pressing UP/DOWN keys here, select SATELLITE SEARCH menu.
SATFINDER4 User Guide ______________________________________________7
Firstly control Satellite, Inb, Diseq-c settings on SATELLITE SEARCH menu,
select FREQUENCY to have a look at signal level and then press OK key and pass
to signal screen. When pressing LEVEL key, you can easily see SIGNAL REPORT.
CHANNEL SEARH MENU :
Please set your dish antenna at the highest level by using values available on screen
of SIGNAL LEVEL. And then, press OK key so as to make NETWORK scanning of
all satellite or single frequency or together with all satellite and you can receive
channels into memory.
SATFINDER4 User Guide ______________________________________________8
SPECTRUM ANALYZER MENU:
Select SPECTRUM ANALYZER from MAIN MENU by pressing MENU key.
After satellite, LNB voltage, Scanning Width and Diseq-c settings are made, press
OK key after you select your IF frequency.
You can see IF frequency and power on the screen of SPECTRUM
ANALYSIS. When you press LEVEL key once on this screen, C/N value will display
on the screen.
By pressing MENU key on the screen of SPECTRUM ANALYSIS, you can
automatically fit levels, convert spectrum levels into lines, save SCANNING lines and
display these lines from memory.
SATFINDER4 User Guide ______________________________________________9
By pressing EDIT key on the screen of SPECTRUM ANALYSIS, YOU can
change parameters such as FREQUENCY, BANDWIDTH, Maximum measurement
value of screen, minimum measurement value of screen and LNB voltages.
You can limit scanning bandwidth on the menu of SPECTRUM ANALYSIS. If
you also mark the signal and press OK key, NETWORK SEARCH will be conducted.
It will be automatically found the values of related TP and matching of dish antenna
with satellite ( under some sensitive circumstances, automatic network scanning can
be out of order) If you press OK key again, Channel Scanning will be conducted.
When you press MENU key and display screen settings of SPECTRUM
ANALYSIS, if you display spectrum screen after selecting DiSEq-C 1.2 Engine,
ENGINE screen will display at the bottom of the screen after you press LEVEL key.
Due to right and left arrows, you can direct DiSEq-C engine towards EAST and
WEST.
SATFINDER4 User Guide _____________________________________________10
DiSEq-C SEARCH MENU:
After you select LNB type and ve DiSEq-C type from menu of DiSEq-C
SCANNING and press OK key, you can see which satellite is connected at which
port.
CHANNEL LIST :
After you press MENU key and mark box of CHANNEL LIST with OK, RADIO
and TV channel list will display on the screen.
If you press MENU key when channel list is open, you can make SATELLITE
selection and see channels pertaining to satellite selected by you.
SATFINDER4 User Guide _____________________________________________11
If you press EDIT key when channel list is open, you can delete channels and
change their locations by moving the channels.
MENU OF SATELLITE DEFINITIONS:
You can make settings of LNB and DiSEq-C on menu of Satellite Identifications and
change DEFAULT TP selection used on menu of AUTOMATIC SCANNING. Thus,
Satellite Search and settings used for other menus shall display from memory.
SETTINGS MENU:
Settings that you will make on menu of SETTINGS shall allow convenience to you
when using device.
SATFINDER4 User Guide _____________________________________________12
MEMORY INFORMATION MENU:
You can see satellite, TP and channel number details on the menu of
MEMORY INFORMATION together with detail about which software is installed on
device. You can also restore the FACTORY DEFAULT SETTINGS and can
completely delete TP and channels from this menu.
BATTERY INFORMATION MENU:
You can see rated current and battery values on the menu of BATTERY
INFORMATION while charging device or operating the device with battery. Thus, you
can see whether remaining period is sufficient or not. You can see warnings related
to temperature and battery in device.
LEVEL INDICATIOR MENU :
When you press LEVEL key while watching selected channel, you can see on
the displayed screen whether signal levels are sufficient or not.
SATFINDER4 User Guide _____________________________________________13
MENU FOR COLOUR VALUES OF SCREEN:
When you press EDIT key on Channel display screen, settings menu
respectively COLOUR, CONTRAST AND BRIGHTNESS will display on the screen.
Thus, you can change screen values according to current light level.
If there is not any image on the screen, the CHANNEL may be encrypted or
there is not sufficient signal level. The warning as above is displayed on the screen.
If you press POWER OFF key on any menu for a few seconds, device will be
turned off automatically. When battery level is low or based on automatic shut-off
time, device will be turned off automatically.
SATFINDER4 User Guide _____________________________________________14
TROUBLESHOOTING:
In the case the screen and the device are not powered on, the following
possibilities may have been the cause:
The charge of device has depleted. If the charger adapter is plugged in and
wait for 10 minutes, it will have power
The ON/OFF switch of the device was not powered.
There may be short circuit on LNB or LNB cable. This may damage your
device otherwise it is not covered by guarantee.
Your device may be damaged or broken down. Apply to your service or dealer
in parallel with the Terms of Guarantee. Do not attempt to repair it on your own
otherwise it is not covered by guarantee.
In the case the device can not be charged, the following possibilities may have
been the cause:
Check that the LED lights on the charger and behind your device are ON. If
the LED lights are not ON, adapters may not have been plugged in well or may have
been broken down. When you plug in your charger, the battery indicator on the right
side of LCD screen will appear as full.
Your device may be damaged or broken down. Apply to your service or dealer
in parallel with the Terms of Guarantee. Do not attempt to repair it on your own
otherwise it is not covered by guarantee.
In case after your satellite direction adjustment, there is no signal and quality
indicator showing any level, the following possibilities may have been the cause:
Check that you made the dish antenna adjustment in correct direction.
Check that whether there is such a tree, building or electric mast before dish antenna
Check that you made correct LNB selection on menu. Quit the menu and check your
LNB adjustment again and the LNB values on your dish antenna.
Check that you made correct satellite selection on menu. Quit the menu and check
the related satellite adjustment again.
Check that whether the frequency you entered is not used anymore. Check the
frequency on www.flysat.com and you can load the current frequencies by the
downloader application Satfinder4 (www.satfinder4.com )
Check that your LNB cable is short circuited or contact problem.
Your LNB may have been broken down.
Your device may be damaged or broken down. Apply to your service or dealer
in parallel with the Terms of Guarantee. Do not attempt to repair it on your own
otherwise it is not covered by guarantee.
SATFINDER4 User Guide _____________________________________________15
TECHNICAL PROPERTIES :
• IF 950 Mhz – 2150 Mhz
• 2 Mb Flash Memory
• 2000 Frequency Memory
• 2000 – 45000 Baud
• Automatic FEC
• Entry -65 dBm ~ -25dBm
• Automatic 22Khz
• All Lnb types
• Convertible LOF
• Convertible TP frequency
• Lnb feeding LnbP21PD
• Diseq-C 1.0 - 1.2 Engine
• 950-2150 mhz Spam Spectrum
• BER , C/N and Power Levels
• 3.5” 960x420 LCD Screen
• 9cm x 15cm x 10cm
• 900 gr Net
• 13V & 18V (+- 1V)
• 500-600 mA LNB CURRENT
• 1950maH 14.8V Lit-Ion Battery
• 3-hour-long battery period
• 220V AC / 12V DC / 800mAH
• F type convertible connector
• Loading software via USB
• Windows 98/Xp/Vista
Supporting
• Sharp Tuner
• 6 Languages option
• User friendly menu
• Quick Software Support
• SMD Component
- 3.5" Lcd Screen
- Broadcast Monitoring from LCD
screen
- 200mhz processor
- 2mB Memory
- Software from USB
- Fast and Precise Navigation
- Direction setting according to
satellite
- Full Band Spectrum Analyzer
- Manual Frequency Change
- Manual LOF Change
- Protection against short circuit
- Sharp 0502 Tuner
- Diseq-c Switch Support
- Auto Diseqc Search
- Multiswitch Support
– One year of guarantee
- 6 different languages option
- Quick charging in 2 hours
- 3-hour-long Lit-_on Battery
period
- Quick Channel Change
- Easy Keyboard
- Camera input from A/V
- Long-lasting bag
- 15cm x 10cm x 9cm
- Signal and power level
- BER , C/N , dBuV level
- Frequencies of 64 satellites
- Memory of 2000 frequencies
- Loading frequency from Pc
- Lightweight and easy carriage
SATFINDER4 User Guide _____________________________________________16
NOTES:……………………………………………………………………………….………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
SATFINDER4 User Guide _____________________________________________17
WARRANTY CONDITIONS
1) Warranty period is minimum a year after the delivery of the device.
2) The life of the charge adaptors and chargeable batteries changes on the basis of
their use all the other components of the product are under the warranty
coverage given by our Company. Charge adaptors and chargeable batteries shall
be delivered by our Company under supply warranty but they are not included in
the warranty coverage herein.
3) If the device has a disorder during the warranty period, the time during the device
was at the service for repair shall be added to the warranty period. The repair
period can not exceed 30 (thirty) work days. This period starts as of the delivery
of the disorder device to the service station or if the service station does not exist,
as of the delivery to the seller, agent, representative, dealer or manufacturer. If
the industrial good can not be repaired within 5 working days, the manufacturer
has to allocate another device with the same or similar characteristics to the
consumer.
4) If the device is subject to a disorder due to workmanship or materials during the
warranty period, the device shall be repaired free of charge without demanding
any payment for workmanship, components or for any other reason. The device
can be delivered to the service by person, if the device is not delivered by person,
the cargo and forwarder fees shall be paid by the consumer. The disorders stem
from the misuse of the consumer shall be repaired against the relevant fees.
5) If the same disorder repeats more than twice within a year during the warranty
period or four different disorders are seen in the device within one year and the
device can not be used continuously for that reason or the time determine for the
repair exceeds or there is no service station or a report stating that the disorder
can not be repaired by the dealer, agent, representative or the manufacturer of
the device, it shall be changed free of charge.
6) The disorders stem from the use of the device for any purpose other than those
stated in the user’s manual are not under the warranty coverage.
7) During the warranty period, no workmanship or other fee is demanded from the
customer for the periodic maintenance services that are said to be compulsory by
the service stations.
8) The consumers have the right to apply to the Ministry of Trade and Industry
Protection of the Customers and Competition General Management for any
problems related to the Warranty Certificates.
SATFINDER4 User Guide _____________________________________________18