Download Installation manual for panic devices.
Transcript
AS45 IP2042EN - rev. 2012-07-24 EN Installation manual for panic devices. (Original instructions) DITEC S.p.A. 9ia 0ons. %an¿ - 21042 Caronno Pertusella (9A) - ITA/< Tel. 02 11 - )a[ 02 014 www.ditec.it - [email protected] INDEX TOPIC PAGE 2 2 4 10 1 17 18 24 2 2 2 /ist of pro¿les and seals /ist of utensils AST PANIC SYSTEM 1. AST mobile wing installation 2. AST ¿[ed wing installation . AST electrical connections ASME PANIC SYSTEM 4. ASME mobile wing installation . ASME electrical connections ASMI PANIC SYSTEM . ASMI mobile wing installation 7. ASMI electrical connections LIST OF PROFILES AND SEALS 100 80 81 87 81 24 88 800 820 2 8 80 821 0 SPAZ14 808 822 417 SPAZ4811 LIST OF UTENSILS Tape measure 10 mm socNet wrench Pencil Drill Pliers Phillips screwdriver Nippers )lathead screwdriver Saw Scissors mm Allen Ne\ 4 mm Allen Ne\ mm Allen Ne\ mm Allen Ne\ /evel .CP) mm Allen Ne\ for tightening the e[panders [18] with special bit All right reserved All data and speci¿cations have been drawn up and checNed with the greatest care. The manufacturer cannot however taNe an\ responsibilit\ for eventual errors ommisions or incomplete data due to technical or illustrative purposes. IP2042EN 2012-07-24 2 AST 2 wings automation kg 120+120 100+100 90+90 80+80 70+70 60+60 40+40 20+20 0 mm 600 800 1000 1200 1400 max MAX 120+120 VALOR B - VALOR N 0 MAX 100+100 TEN MAX 90+90 VALOR L - VALOR P MAX 70+70 REX If the width of the mobile panic wing (/M) is greater than 1000 mm add reinforcement 417 (see ¿g. 1) If the width of the mobile panic wing (/M) is greater than 1200 mm add reinforcement the third carriage. If the weight of the mobile panic wing is greater than 0 Ng add Nit .AS4 to the lower portion (see ref. 1 ¿g. 2). Note: 2nO\ Ior 3$0/ ,I the weight oI the door does not e[ceed Ng use the .,F Nit in the Oower Sart see reI ¿g The ma[imum height of the ¿[ed panic wing (+)) must not e[ceed 2400 mm. AST panic devices are TÜV approved for use with DITEC TEN and VA/O5 model automations. Each carriage installed must be connected to the mobile panic wing b\ at least two fastening points. The wings to be used are intended as having been built with DITEC PAM4/ and PAM4M series pro¿les. The ma[imum height of the mobile panic wing (+M) must not e[ceed 2400 mm. The dimensions (/M) and the ma[imum weight of the door that can be NnocNed out must compl\ with the following graphs for one and two mobile door automations. Note: For dimensions and/or weights which are not accounted Ior in the diagram con¿rm the IeasiEiOit\ oI the SroMect with our technicaOcommerciaO oI¿ces kg The width of the ¿[ed panic wing (/)) must not e[ceed 100 mm and the weight must not e[ceed 100 Ng. 1 wing automation 120 100 80 60 40 20 0 0 10 1 KIT Q.T. AST1 AST1 1 Q.T. AST2 Q.T. SE5IES 1 1 2 KAS4 AST2 2--4--7-2 10 820 24 100 417 SPAZ4811 1-11-12-114-1-117-18-120-21-222-24-2 KASM14 KASM24 KI)4 KASMG14 KASMN14 1 2 PAM4/ PAM4M KAST1A4) 1 2 PAM4/ PAM4M 27 1CE/P5 2 2 PAM4/ PAM4M REF. KIT SERIE PAM4/ PAM4/ PAM4M PAM4/ PAM4M PAM4/ Note: 8se .it &(/35 iI \ou wish to instaOO the ShotoceOOs that detect the Sresence oI SeoSOe and oEMects in the Sassage cham Eer see reI Sag mm 600 800 1000 1200 1400 max MAX 120 VALOR B - VALOR N i MAX 100 VALOR L - VALOR P - REX - TEN 3 $ttention: 8se the 3$0/ $67 or 3$00 $67 manuaOs to determine the cut measurements, the kits required and the required Sro¿Oe SreSarations IP2042EN 2012-07-24 1. AST MOBILE WING INSTALLATION () Onl\ with /M ! 1000 5 7 *4173 3820 340 3 6 SPAZ4811 35 33 4 16 35 33 3924 4xØ4,2 SPAZ4811 4xØ6,5 30 19 150 98 45 56 7 17 HM 4xØ6,5 30 330 24 24 2xØ6,5 40 30 3 600< LM 30x30 2 < 1400 1600 )ig. 1 IP2042EN 2012-07-24 4 () PAM4/ () Onl\ with mobile wing ! 0 Ng Adjustments to be performed during installation 6 3 3820+SPAZ4811 5 7 6 160 3924+SPAZ4811 4 1 8 4 1 26 6 3813 (*3822)+3839 8 3808 (*3821)+3839 8 3831+3838 3808 (*3821)+3839 3837 9 *10 *10 8 3805+SPAZ14 1600 2 ** 1 3800 (*3599)+3839 ** 1 )ig. 2 5 IP2042EN 2012-07-24 1.1 Insert the seal 8 into the PAM4M pro¿les 800 808 and 81 or else the PAM4/ pro¿les 821 and 822 as shown in the diagram. 1.4 -oin the vertical pro¿les with the hori]ontal pro¿les and fasten them as shown in the diagram. Note: :ith 3$0/ Sro¿Oes, the gOass >@ must Ee inserted when Moining the YerticaO and hori]ontaO Sro¿Oes 7he gOass suSSort sSacers must Ee SroSerO\ aSSOied to the Iour sides and must Ee adMusted as shown in SaragraSh 1.2 Shorten the seal to the si]e of the pro¿le. 1. )asten pro¿le 80 to the lower portion of the wing as shown in the diagram. 1. Insert detail [1] into the PAM4M pro¿les 800 and 81 or else the PAM4/ pro¿les and 822 and fasten it as shown in the diagram. 1. Insert the brushes SPAZ14 as shown in the diagram and blocN them to prevent them from sliding. IP2042EN 2012-07-24 6 1.7 Insert detail [2] into the lower portion of the wing and fasten it as shown in the diagram. 1.11 )asten pro¿le 24 to the upper portion of the wing as shown in the diagram. 1.8 Insert detail [] into the upper portion of the wing as shown in the diagram. 1.12 )asten detail [4] to pro¿le 24 as shown in the diagram. Note: %e sure to take note oI the wing¶s oSening direction 1. )asten detail [] b\ tightening the eight fastening screws as shown in the diagram. 1.1 Trim the brush SPAZ4811 where it connects with detail [] as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction 1.10 Insert the brush SPAZ4811 into pro¿les 24 and 820 as shown in the diagram. 1.14 Insert pro¿le 820 into detail [] as shown in the diagram. 7 IP2042EN 2012-07-24 1.1 )asten detail [] to pro¿le 820 as shown in the diagram. 1.18 Position detail [] in correspondence to detail [4] and fasten it as shown in the diagram.a. Note: during the instaOOation of the ¿[ture, in order to oEtain the SroSer Ereakawa\ strength for the moEiOe wing, use the OateraO screws to adMust detaiO >@, as shown in the diagram Note: during the instaOOation of the ¿[ture, in order to oEtain the SroSer hori]ontaO Sosition of the moEiOe Sanic wing, Ooosen the fastening screws and adMust the screw shown in detaiO >@, as shown in the diagram 1.1 Insert detail [] into pro¿le 820 near detail [] as shown in the diagram. 1.1 Insert the seal 87 onto the PAM4M pro¿le 808 or else the PAM4/ pro¿le 821 as shown in the diagram. $ttention: 2rient seaO as indicated in the ¿[tures manuaO 0ake a hoOe in the seaO that corresSonds with the thickness adMustment of the Sush gOass >@ as shown in the Sicture 1.1 If the width of the mobile wing is greater than 1000 mm insert reinforcement 417 into pro¿le 820 as shown in the diagram. 1.21 Insert detail [7] into pro¿le 820 as shown in the diagram. $ttention: 2rient detaiO >@ in the same manner as seaO 1.17 Insert detail [] into pro¿le 820 as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction IP2042EN 2012-07-24 8 1.2 :ith PAM4M pro¿les insert the glass [] into the mobile wing as shown in the diagram. 1.22 Attach the supplied hooN to the lower part of the wing as shown in the diagram in order to prevent seal 87 from sliding. A A 1.27 Set the glass spacers [A] shown in the diagram so that the\ provide proper support. NB: when instaOOing the ¿tting, adMust the Sush gOass sSacers >@ as shown in the Sicture , for the moEiOe door wing to reach the hori]ontaO Sosition. 1.2 Attach pro¿le 81 to the PAM4M pro¿le 808 or else to the PAM4/ pro¿le 821 as shown in the diagram. 1.28 :ith PAM4M pro¿les insert the seals into the glass-blocNing pro¿les [8] as shown in the diagram. 1.24 Insert seal 88 into pro¿le 81 as shown in the diagram and blocN it to prevent it from sliding. 1.2 :ith PAM4M pro¿les insert the glass-blocNing pro¿les [8] onto the mobile wing until the\ clicN as shown in the diagram. 1.2 Close the visible holes with the supplied caps as shown in the diagram. 9 IP2042EN 2012-07-24 2. AST FIXED WING INSTALLATION 3809+SPAZ4811 22 21 23 3924+SPAZ4811 15 14 17 3924 + SPAZ4811 3809 + SPAZ4811 HM 19 13 16 13 LM 11 12 24 20 )ig. IP2042EN 2012-07-24 10 () PAM4/ Adjustments to be performed during installation ------- Photocell and magnetic micro-switch cable route 3809+SPAZ4811 21 3924+SPAZ4811 18 22 23 15 17 18 13 14 25 4 6 19 10 8 6 3813+(*3822)+3839 16 10 18 6 8 3808 (*3821)+3839 8 3808 (*3821)+3839 3831 3924+ SPAZ4811 18 27 6 9 3809 + SPAZ4811 18 6 27 10 8 10 11 12 13 20 3800 (*3599)+3839 3805 + SPAZ14 24 )ig. 4 11 IP2042EN 2012-07-24 2.1 Insert the seal 8 into the PAM4M pro¿les 800 808 and 81 or else the PAM4/ pro¿les 821 and 822 as shown in the diagram. 2.4 Insert detail [11] into the lower portion of the wing and fasten it as shown in the diagram. 2. Insert the brushes SPAZ14 upon pro¿le 80 and blocN them to prevent them from sliding. )asten pro¿le 80 to the lower portion of the wing as shown in the diagram. 2.2 Shorten the seal to the si]e of the pro¿le. 2. Insert detail [12] into the lower portion of the wing and fasten it as shown in the diagram. 2. -oin the vertical pro¿les with the hori]ontal pro¿les and fasten them as shown in the diagram. Note: :ith 3$0/ Sro¿Oes, ,nsert detaiO >@ into Sro¿Oes and , as shown in the diagram Note: :ith 3$0/ Sro¿Oes, the gOass >@ must Ee inserted when Moining the YerticaO and hori]ontaO Sro¿Oes 7he gOass suSSort sSacers must Ee SroSerO\ aSSOied to the four sides and must Ee adMusted as shown in SaragraSh IP2042EN 2012-07-24 2.7 Insert the photocell [2] which detects the opening of the mobile wing into pro¿le 81 as shown in the diagram. NB: the ShotoceOOs >@ that detect the Sresence of SeoSOe and oEMects in the Sassage chamEer can Ee inserted as shown in Sicture 12 2.12 Attach the magnetic limit switch [1] to its relative bracNet as shown in the diagram. 2.8 )eed the cable through the upper portion of the wing and maNe it to come out in order to allow for the connection of the magnetic limit switch as shown in the diagram. 2.1 Insert the brush SPAZ4811 into pro¿les 24 and 80 as shown in the diagram and blocN it to prevent it from sliding. 2. MaNe the limit switch and photocells cables come out of the hinge side vertical upright as shown in the diagram. 2.10 Attach pro¿le 81 and insert detail [1] as shown in the diagram. 2.14 )asten detail [1] to pro¿le 24 as shown in the diagram. 2.11 Insert and fasten detail [14] as shown in the diagram. Note: 'uring the instaOOation of the ¿[ture, adMust detaiO >@ so that detaiO >@ is SroSerO\ connected Eetween the ¿[ed wing ad the Serimeter Sro¿Oe 2.1 )eed the cable through the upper portion of the wing and maNe it to come out in correspondence to the photocell cable as shown in the diagram. 13 IP2042EN 2012-07-24 2.20 )asten the e[panders [18] to the perimeter pro¿les 80 as shown in the diagram using the appropriate mm Allen Ne\. Note: 'uring the instaOOation of the ¿[ture, the Serimeter Sro ¿Oes must Ee attached to the waOO and OeYeOed with the e[Sanders 2.1 )asten pro¿le 24 to the upper portion of the wing and perform the proper connections as shown in the diagram maNing reference to page 1. 2.21 )asten detail [1] to pro¿le 80 as shown in the diagram. Note: 'uring the instaOOation of the ¿[ture, the caEOes coming out of the ¿[ed wing must Ee fed through detaiO >@ 2.17 )asten detail [1] to pro¿le 24 as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction 2.22 )asten detail [20] to the lower portion of pro¿le 80 as shown in the diagram. 2.18 )asten pro¿le 24 to the hinge side vertical upright as shown in the diagram. 2.2 )asten detail [21] to the upper portion of pro¿le 80 as shown in the diagram. 2.1 )asten detail [17] as shown in the diagram. IP2042EN 2012-07-24 14 2.24 )asten detail [22] to pro¿le 80 situated above the wing as shown in the diagram. Note: 'uring the instaOOation of the ¿[ture, detaiO >@ must Ee Sositioned in corresSondence to its internaO connection with de taiO >@ and the Erush 63$= must Ee trimmed ,n addition, in order to oEtain the SroSer Ereakawa\ strength for the ¿[ed wing, use the OateraO screws to adMust detaiO >@ 2.28 :ith PAM4M pro¿les insert the seals into the glass-blocNing pro¿les [8] as shown in the diagram. 2.2 During the installation of the ¿[ture detail [2] must be positioned in correspondence to the magnetic limit switch [1]. Drill the appropriate holes in order to fasten detail [2] to pro¿le 80 situated above the wing as shown in the diagram. 2.2 :ith PAM4M pro¿les insert the glass-blocNing pro¿les [8] onto the mobile wing until the\ clicN as shown in the diagram. 2.2 :ith PAM4M pro¿les insert the glass [] into the ¿[ed wing as shown in the diagram. 2.0 During the installation of the ¿[ture position detail [24] in correspondence to detail [11] on the ¿[ed wing and fasten it to the Àoor so that it is aligned with the ¿[ture as shown in the diagram. A A 2.1 During the installation of the ¿[ture fasten pro¿le 100 to the Àoor as shown in the PAM4/ AST or PAM4M AST manual. Note: 'o not Saint Sro¿Oe after it has Eeen fastened to the Àoor 2.27 Set the glass spacers [A] shown in the diagram so that the\ provide proper support. 15 IP2042EN 2012-07-24 9 STOP Brown Blue Brown Blue OPEN Magnetic switch 9 Black Blue 1 0 Brown 23 COMH-K AST ELECTRICAL CONNECTIONS CONTROL PANEL 3 23 OPEN 15 15 TX RX Magnetic switch Black Brown Blue Black DO NOT CONNECT 25 RX 25 TX LED Black Grey - - 103 - 25 - 13 - IP2042EN 2012-07-24 16 Perform the electrical connections as shown in the diagram. $ttention: ,f the &20+. function seOector is used, connect the receiYer¶s Erown caEOe to terminaO on the seOector An\ other arrest devices must be connected in series to terminal (STOP). :hen the receiver (5;) and the transmitter (T;) of the photocell SIC852 are powered and correctl\ aligned the green /ED on the transmitter T; and the \ellow /ED on the receiver 5; will light up. The \ellow /ED on the receiver will go out when the\ are no longer correctl\ aligned. Once installation has been completed checN to maNe sure that the force required to open each single wing does not e[ceed 220 N. This reading must be taNen at 1 m from Àoor level in correspondence to the closure side of the wing (opposite to the hinges). The breaNawa\ force can be adjusted as indicated in paragraph 1.18 and 2.24. ChecN that the door¶s automatic movement stops when the wings (mobile and ¿[ed) are released. The SIC852 photocell serves the purpose of detecting the release of the mobile wings while the magnetic micro-switch serves the purpose of detecting the release of the ¿[ed wings. If installed the photocells CE/P5 [27] that detect the presence of people and objects in the passage chamber must be connected as shown in the manual of the electronic control panel of the automation s\stem. ASME 1 wing automation kg 120 100 80 60 40 20 0 mm 600 800 1000 1200 1400 max 0 MAX 120 VALOR B - VALOR N MAX 100 VALOR L - VALOR P - REX - TEN 2 wings automation kg 120+120 100+100 90+90 80+80 70+70 60+60 40+40 20+20 0 mm 600 800 1000 1200 1400 max MAX 120+120 VALOR B - VALOR N 0 ASME panic devices are TÜV approved for use with DITEC TEN and VA/O5 model automations. Each carriage installed must be connected to the mobile panic wing b\ at least two fastening points. The wings to be used are intended as having been built with DITEC PAM4/ and PAM4M series pro¿les. Note: 7he $60( Sanic s\stem can aOso Ee aSSOied to wings which haYe Eeen EuiOt with non'itec Sro¿Oes 7he kits .$60, .$60 and .$60*/.$60N must Ee used, as indicated in the taEOe 7he si]e and weight Oimits indicated EeOow must Ee resSected when assemEOing the wings 7he aOuminum Sro¿Oes used to construct the Sanic wings must Ee comSatiEOe with the $60( Sanic s\stem 3erform an\ work required in order to adaSt the kits, making reference to the measurements indicated in the 3$0 $60( manuaOs 7h9 aSSroYaO wiOO Ee Yoid in the case that non'itec Sro¿Oes are emSOo\ed The ma[imum height of the mobile panic wing (+M) must not e[ceed 2400 mm. MAX 100+100 TEN MAX 90+90 VALOR L - VALOR P MAX 70+70 REX If the width of the mobile panic wing (/M) is greater than 1000 mm add reinforcement 417 (see ¿g. ) If the width of the mobile panic wing (/M) is greater than 1200 mm add reinforcement the third carriage. If the weight of the mobile panic wing is greater than 0 Ng add Nit KAS4 to the lower portion (see ref. 1 ¿g. ). Note: onO\ for 3$0/ ,f the weight of the wing is not greater than kg, use kit .,F to the Oower Sortion see ref ¿g The following table lists the contents of the Nits. REF. 10 1 The dimensions (/M) and the ma[imum weight of the door that can be NnocNed out must compl\ with the following graphs for one and two mobile door automations. Note: For dimensions and/or weights which are not accounted for in the diagram, con¿rm the feasiEiOit\ of the SroMect with our technicaOcommerciaO of¿ces KIT KIT Q.T. ASME1 1 KAS4 1 1-2 KASM1A4) 1 2--4--7-2 KASM14 KASM24 1 - 2 KASME4 1 Q.T. SERIES ASME2 1 PAM4/ PAM4/ 2 PAM4M PAM4/ 2 PAM4M 1 PAM4/ PAM4M 1 PAM4/ 1 PAM4M 820 24 PAM4/ KASMG14 1 2 100 PAM4M KASMN14 417 SPAZ4811 $ttention: 8se the 3$0/ $60( or 3$00 $60( manuaOs to determine the cut measurements, the kits required and the required Sro¿Oe SreSarations i 17 IP2042EN 2012-07-24 4. ASME MOBILE WING INSTALLATION () Onl\ with /M ! 1000 5 7 *4173 3820 340 3 6 SPAZ4811 35 33 4 16 35 33 3924 4xØ4,2 SPAZ4811 4xØ6,5 30 19 150 98 45 56 7 17 HM 4xØ6,5 30 330 24 24 2xØ6,5 40 30 3 600< LM 30x30 2 < 1400 1600 )ig. IP2042EN 2012-07-24 18 () PAM4/ () Onl\ with mobile wing ! 0 Ng Adjustments to be performed during installation 6 3 3820+SPAZ4811 5 7 6 160 3924+SPAZ4811 4 1 8 4 1 26 6 3813 (*3822)+3839 8 3808 (*3821)+3839 8 3925 3808 (*3821)+3839 3837 9 *10 *10 8 3805+SPAZ14 1600 2 ** 1 3800 (*3599)+3839 ** 1 )ig. 19 IP2042EN 2012-07-24 4.1 Insert the seal 8 into the PAM4M pro¿les 800 808 and 81 or else the PAM4/ pro¿les 821 and 822 as shown in the diagram. 4.4 -oin the vertical pro¿les with the hori]ontal pro¿les and fasten them as shown in the diagram. Note: :ith 3$0/ Sro¿Oes, the gOass >@ must Ee inserted when Moining the YerticaO and hori]ontaO Sro¿Oes 7he gOass suSSort sSacers must Ee SroSerO\ aSSOied to the four sides and must Ee adMusted as shown in SaragraSh 4.2 Shorten the seal to the si]e of the pro¿le. 4. )asten pro¿le 80 to the lower portion of the wing as shown in the diagram. 4. Insert detail [1] into the PAM4M pro¿les 800 and 81 or else the PAM4/ pro¿les and 822 and fasten it as shown in the diagram. 4. Insert the brushes SPAZ14 as shown in the diagram and blocN them to prevent them from sliding. IP2042EN 2012-07-24 20 4.7 Insert detail [2] into the lower portion of the wing and fasten it as shown in the diagram. 4.11 )asten pro¿le 24 to the upper portion of the wing as shown in the diagram. 4.8 Insert detail [] into the upper portion of the wing as shown in the diagram. 4.12 )asten detail [4] to pro¿le 24 as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction 4. )asten detail [] b\ tightening the eight fastening screws as shown in the diagram. 4.1 Trim the brush SPAZ4811 where it connects with detail [] as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction 4.10 Insert the brush SPAZ4811 into pro¿les 24 and 820 as shown in the diagram and blocN it to prevent it from sliding. 4.14 Insert pro¿le 820 into detail [] as shown in the diagram. 21 IP2042EN 2012-07-24 4.1 )asten detail [] to pro¿le 820 as shown in the diagram. 4.18 Position detail [] in correspondence to detail [4] and fasten it as shown in the diagram. Note: during the instaOOation of the ¿[ture, in order to oEtain the SroSer Ereakawa\ strength for the moEiOe wing, use the OateraO screws to adMust detaiO >@, as shown in the diagram 4.1 Insert detail [] into pro¿le 820 near detail [] as shown in the diagram. Note: during the instaOOation of the ¿[ture, in order to oEtain the SroSer hori]ontaO Sosition of the moEiOe Sanic wing, Ooosen the fastening screws and adMust the screw shown in detaiO >@, as shown in the diagram 4.20 Insert the seal 87 onto the PAM4M pro¿le 808 or else the PAM4/ pro¿le 821 as shown in the diagram. $ttention: 2rient seaO as indicated in the ¿[tures manuaO 0ake a hoOe in the seaO that corresSonds with the thickness adMustment of the Sush gOass >@ as shown in the Sicture 4.1 If the width of the mobile wing is greater than 1000 mm insert reinforcement 417 into pro¿le 820 as shown in the diagram. 4.21 Insert detail [7] into pro¿le 820 as shown in the diagram. $ttention: 2rient detaiO >@ in the same manner as seaO 4.17 Insert detail [] into pro¿le 820 as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction IP2042EN 2012-07-24 22 A A 4.22 Attach the supplied hooN to the lower part of the wing as shown in the diagram in order to prevent seal 87 from sliding. 4.2 Set the glass spacers [A] shown in the diagram so that the\ provide proper support. NB: when instaOOing the ¿tting, adMust the Sush gOass sSacers >@ as shown in the Sicture , for the moEiOe door wing to reach the hori]ontaO Sosition 4.2 :ith PAM4M pro¿les insert the seals into the glass-blocNing pro¿les [8] as shown in the diagram. 4.2 Attach pro¿le 2 to the PAM4M pro¿le 808 or else to the PAM4/ pro¿le 821 as shown in the diagram. 4.27 :ith PAM4M pro¿les insert the glass-blocNing pro¿les [8] onto the mobile wing until the\ clicN as shown in the diagram. 4.24 :ith PAM4M pro¿les insert the glass [] into the mobile wing as shown in the diagram. 23 IP2042EN 2012-07-24 COMH-K ASME ELECTRICAL CONNECTIONS 9 STOP DO NOT CONNECT Brown Blue Black Blue 1 0 Brown OPEN 9 CONTROL PANEL 5. OPEN TX RX Grey Black 25 RX 25 TX LED Black Grey - - 96,5 - - 25 13 - IP2042EN 2012-07-24 24 The SIC852 photocell must be installed upon the head of the automation. Perform the electrical connections as shown in the diagram. $ttention: ,f the &20+. function seOector is used, connect the receiYer¶s Erown caEOe to terminaO on the seOector An\ other arrest devices must be connected in series to terminal (STOP). :hen the receiver (5;) and the transmitter (T;) of the photocell SIC852 are powered and correctl\ aligned the green /ED on the transmitter T; and the \ellow /ED on the receiver 5; will light up. The \ellow /ED on the receiver will go out when the\ are no longer correctl\ aligned. Once installation has been completed checN to maNe sure that the force required to open each single wing does not e[ceed 220 N. This reading must be taNen at 1 m from Àoor level in correspondence to the closure side of the wing (opposite to the hinges). The breaNawa\ force can be adjusted as indicated in paragraph 4.18. ChecN that the door¶s automatic movement stops when the mobile wings are released. The SIC852 photocell serves the purpose of detecting the release of the mobile wings. ASMI 1 wing automation kg 120 100 80 60 40 20 0 mm 600 800 1000 1200 1400 max 0 MAX 120 VALOR B - VALOR N MAX 100 VALOR L - VALOR P - REX - TEN 2 wings automation kg 120+120 100+100 90+90 80+80 70+70 60+60 40+40 20+20 0 mm 600 800 1000 1200 1400 max MAX 120+120 VALOR B - VALOR N 0 ASMI panic devices are TÜV approved for use with DITEC TEN and VA/O5 model automations $ttention: 7he $60, Sanic s\stem wiOO onO\ function whiOe the wings are comSOeteO\ cOosed Each carriage installed must be connected to the mobile panic wing b\ at least two fastening points. The wings to be used are intended as having been built with DITEC PAM4/ and PAM4M series pro¿les. Note: 7he $60, Sanic s\stem can aOso Ee aSSOied to wings which haYe Eeen EuiOt with non'itec Sro¿Oes 7he kits .$60, .$60 and .$60*/.$60N must Ee used, as indicated in the taEOe 7he si]e and weight Oimits indicated EeOow must Ee resSected when assemEOing the wings 7he aOuminum Sro¿Oes used to construct the Sanic wings must Ee comSatiEOe with the $60, Sanic s\stem 3erform an\ work required in order to adaSt the kits, making reference to the measurements indicated in the 3$0 $60, manuaOs 7h9 aSSroYaO wiOO Ee Yoid in the case that non'itec Sro¿Oes are emSOo\ed The ma[imum height of the mobile panic wing (+M) must not e[ceed 2400 mm. The dimensions (/M) and the ma[imum weight of the door that can be NnocNed out must compl\ with the following graphs for one and two mobile door automations. Note: For dimensions and/or weights which are not accounted for in the diagram, con¿rm the feasiEiOit\ of the SroMect with our technicaOcommerciaO of¿ces MAX 100+100 TEN MAX 90+90 VALOR L - VALOR P MAX 70+70 REX If the width of the mobile panic wing (/M) is greater than 1000 mm add reinforcement 417 (see ¿g. 7) If the width of the mobile panic wing (/M) is greater than 1200 mm add reinforcement the third carriage. If the weight of the mobile panic wing is greater than 0 Ng add Nit KAS4 to the lower portion (see ref. 1 ¿g. 8). Note: onO\ for 3$0/ ,f the weight of the wing is not greater than kg, use kit .,F to the Oower Sortion see ref ¿g The following table lists the contents of the Nits. KI)4 Q.T. ASMI1 1 Q.T. ASMI2 1 KAS4 1 2 1-2 KASM1A4) 1 2 2--4--7-2 820 24 100 417 SPAZ4811 KASM14 KASM24 1 - 1 1 KASMG14 KASMN14 1 2 RIF. 10 1 i 25 KIT SERIES PAM4/ PAM4/ PAM4M PAM4/ PAM4M PAM4/ PAM4M PAM4/ PAM4M $ttention: 8se the 3$0/ $60, or 3$00 $60, ma nuaOs to determine the cut measurements, the kits required and the required Sro¿Oe SreSarations IP2042EN 2012-07-24 6. ASMI MOBILE WING INSTALLATION () Onl\ with /M ! 1000 5 7 *4173 3820 3 6 SPAZ4811 150 98 4 16 3924 4xØ4,2 SPAZ4811 30 19 4xØ6,5 3930 HM 30 4xØ6,5 330 24 40 30 2xØ6,5 24 LM 2 1600 )ig. 7 IP2042EN 2012-07-24 26 () PAM4/ () Onl\ with mobile wing ! 0 Ng Adjustments to be performed during installation 6 3 3820+SPAZ4811 5 7 6 160 3924+SPAZ4811 4 1 8 4 1 26 6 3813 (*3822)+3839 8 3808 (*3821)+3839 8 3930 3808 (*3821)+3839 3837 9 *10 *10 8 3805+SPAZ14 1600 2 ** 1 3800 (*3599)+3839 ** 1 )ig. 8 27 IP2042EN 2012-07-24 .1 Insert the seal 8 into the PAM4M pro¿les 800 808 and 81 or else the PAM4/ pro¿les 821 and 822 as shown in the diagram. .4 -oin the vertical pro¿les with the hori]ontal pro¿les and fasten them as shown in the diagram. Note: :ith 3$0/ Sro¿Oes, the gOass >@ must Ee inserted when Moining the YerticaO and hori]ontaO Sro¿Oes 7he gOass suSSort sSacers must Ee SroSerO\ aSSOied to the four sides and must Ee adMusted as shown in SaragraSh .2 Shorten the seal to the si]e of the pro¿le.. . )asten pro¿le 80 to the lower portion of the wing as shown in the diagram. . Insert detail [1] into the PAM4M pro¿les 800 and 81 or else the PAM4/ pro¿les and 822 and fasten it as shown in the diagram. . Insert the brushes SPAZ14 as shown in the diagram and blocN them to prevent them from sliding. IP2042EN 2012-07-24 28 .7 Insert detail [2] into the lower portion of the wing and fasten it as shown in the diagram. .11 )asten pro¿le 24 to the upper portion of the wing as shown in the diagram. .8 Insert detail [] into the upper portion of the wing as shown in the diagram. .12 )asten detail [4] to pro¿le 24 as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction . )asten detail [] b\ tightening the eight fastening screws as shown in the diagram. .1 Trim the brush SPAZ4811 where it connects with detail [] as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction .10 Insert the brush SPAZ4811 into pro¿les 24 and 820 as shown in the diagram and blocN it to prevent it from sliding. .14 Insert pro¿le 820 into detail [] as shown in the diagram. 29 IP2042EN 2012-07-24 .1 )asten detail [] to pro¿le 820 as shown in the diagram. .18 Position detail [] in correspondence to detail [4] and fasten it as shown in the diagram. Note: during the instaOOation of the ¿[ture, in order to oEtain the SroSer Ereakawa\ strength for the moEiOe wing, use the OateraO screws to adMust detaiO >@, as shown in the diagram Note: during the instaOOation of the ¿[ture, in order to oEtain the SroSer hori]ontaO Sosition of the moEiOe Sanic wing, Ooosen the fastening screws and adMust the screw shown in detaiO >@, as shown in the diagram .1 Insert detail [] into pro¿le 820 near detail [] as shown in the diagram. .1 If the width of the mobile wing is greater than 1000 mm insert reinforcement 417 into pro¿le 820 as shown in the diagram. .20 Insert the seal 87 onto the PAM4M pro¿le 808 or else the PAM4/ pro¿le 821 as shown in the diagram. $ttention: 2rient seaO as indicated in the ¿[tures manuaO 0ake a hoOe in the seaO that corresSonds with the thickness adMustment of the Sush gOass >@ as shown in the Sicture .17 Insert detail [] into pro¿le 820 as shown in the diagram. Note: Be sure to take note of the wing¶s oSening direction .21 Insert detail [7] into pro¿le 820 as shown in the diagram. $ttention: 2rient detaiO >@ in the same manner as seaO IP2042EN 2012-07-24 30 .2 :ith PAM4M pro¿les insert the glass [] into the mobile wing as shown in the diagram. .22 Attach the supplied hooN to the lower part of the wing as shown in the diagram in order to prevent seal 87 from sliding. A A .2 Set the glass spacers [A] shown in the diagram so that the\ provide proper support. NB: when instaOOing the ¿tting, adMust the Sush gOass sSacers >@ as shown in the Sicture , for the moEiOe door wing to reach the hori]ontaO Sosition .2 Attach pro¿le 0 to the PAM4M pro¿le 808 or else to the PAM4/ pro¿le 821 as shown in the diagram. .27 :ith PAM4M pro¿les insert the seals into the glass-blocNing pro¿les [8] as shown in the diagram. .24 Close the visible holes with the supplied caps as shown in the diagram. .28 :ith PAM4M pro¿les insert the glass-blocNing pro¿les [8] onto the mobile wing until the\ clicN as shown in the diagram. 31 IP2042EN 2012-07-24 9 STOP DO NOT CONNECT Brown Blue 9 Black Blue 1 0 Brown OPEN COMH-K ASMI ELECTRICAL CONNECTIONS CONTROL PANEL 7. OPEN TX RX Grey Black 25 RX 25 TX LED Black Grey - - - 103 - 25 13 - IP2042EN 2012-07-24 32 The SIC852 photocell must be installed upon the perimeter pro¿le or else upon the ¿[ed wing as shown in the diagram and in the PAM4 ASMI manual. Perform the electrical connections as shown in the diagram. $ttention: ,f the &20+. function seOector is used, connect the receiYer¶s Erown caEOe to terminaO on the seOector An\ other arrest devices must be connected in series to terminal (STOP). :hen the receiver (5;) and the transmitter (T;) of the photocell SIC852 are powered and correctl\ aligned the green /ED on the transmitter T; and the \ellow /ED on the receiver 5; will light up. The \ellow /ED on the receiver will go out when the\ are no longer correctl\ aligned.0 Once installation has been completed checN to maNe sure that the force required to open each single wing does not e[ceed 220 N. This reading must be taNen at 1 m from Àoor level in correspondence to the closure side of the wing (opposite to the hinges). The breaNawa\ force can be adjusted as indicated in paragraph .18. ChecN that the door¶s automatic movement stops when the mobile wings are released. The SIC852 photocell serves the purpose of detecting the release of the mobile wings. OPERATING INSTRUCTION FOR BREAK OUT SLIDING DOORS The label supplied must be attached in a visible position on each mobile door that can be breaN out [a] in the direction of the escape. b a a b TEAR OFF AND DELIVER TO USER The breaN out of mobile doors [a] and semi-¿[ed doors [b] if present is obtained b\ pushing the doors in the direction of the escape. A force of no more than 220 N near the closing edge at a height of appro[imatel\ 1 m from ground level is suf¿cient. %\ breaN out the doors the motorised function is interrupted and the door can onl\ be moved manuall\. b a a To restore automatic function of the sliding door partiall\ open the breaN-out mobile doors and manuall\ reposition each door. Start with the mobile doors [a] and then the semi-¿[ed doors [b] bringing them bacN to their initial position. :arning: 'oors must not Ee comSOeteO\ cOosed b Le ante non devono essere completamente chiuse. Wings must not be completely closed. a b a b Installer: TM DITEC S.p.A. Via Mons. %an¿ 21042 Caronno Pertusella (VA) - ITA/< Tel. 02 11 - )a[ 02 014 www.ditec.it - [email protected] 33 IP2042EN 2012-07-24 TM DITEC S.p.A. Via Mons. %an¿ 21042 Caronno P.lla (VA) Ital\ Tel. 02 11 )a[ 02 014 www.ditec.it [email protected] DITEC BELGIUM /OKE5EN Tel. 2 001 )a[ 2 002 www.ditecbelgium.be DITEC DEUTSCHLAND O%E585SE/ Tel. 4 171 1410 )a[ 4 171 141 www.ditec-german\.de DITEC ESPAÑA A5EN<S DE MA5 Tel. 4 78 )a[ 4 702 www.ditecespana.com DITEC FRANCE MASS< Tel. 1 4280 )a[ 1 4281 www.ditecfrance.com DITEC GOLD PORTA E5MESINDE-PO5T8GA/ Tel. 1 22 7720 )a[ 1 22 77288 www.goldporta.com DITEC SVIZZERA %A/E5NA Tel. 41 848 88 )a[ 41 1 4127 www.ditecswiss.ch DITEC ENTREMATIC NORDIC /ANDSK5ONA-S:EDEN Tel. 4 418 14 0 )a[ 4 418 11 www.ditecentrematicnordic.com DITEC TURCHIA ISTAN%8/ Tel. 0 21 287780 )a[ 0 21 287778 www.ditec.com.tr DITEC AMERICA O5/ANDO-)/O5IDA-8SA Tel. 1 407 8880 )a[ 1 407 888227 www.ditecamerica.com DITEC CHINA S+ANG+AI Tel. 8 21 2812 )a[ 8 21 28 www.ditec.cn