Download DGP-848 : Reference and Installation Manual

Figure 19: Example of Keyswitch Numbering
5.2.5 Generates a Utility Key Event on Open and Close
SECTIONS [149] TO [156]: SECOND DIGIT = 4
When option [4] is enabled, a Utility Key Event will be generated
whenever the keyswitch input is opened or closed. As a result, the
Utility Key Events increase from 32 to 64 events when option [4] is
enabled; one event for each state (open and closed). See Table 12
on page 35. This option can be used to activate or deactivate one
or more of DGP-848’s PGM outputs. When a keyswitch is defined
with the Generate a Utility Key Event on Open and Close option,
the Keyswitch Partition Assignment and Keyswitch Options are
disabled. To program a Keyswitch to generate a Utility Key Event:
1)
2)
Program the Activation Event of a PGM output with the Utility
Key Event corresponding to the desired keyswitch (see PGM
Programming Table in the Programming Guide).
Enable option [4] in the section corresponding to the desired
keyswitch.
5.3 Keyswitch Partition Assignment
5.2 Keyswitch Definitions
Select one of the keyswitch definitions (also see Figure 18 on page 17):
SECTIONS [149] TO [156]: SECOND DIGIT = 1 TO 4
The control panel provides the option of partitioning the security
system into two, three, or four completely independent systems.
Therefore, each keyswitch must be assigned to one partition as
described in Figure 18 on page 17. For more information on
Partitioning, refer to section 12.5 on page 36.
5.2.1 Keyswitch Disabled
5.4 Keyswitch Options
SECTIONS [149] TO [156]: FIRST DIGIT = 0
Disables keyswitch input.
Each keyswitch zone can be programmed with one or more of the
options (also see Figure 18 on page 17):
5.2.2 Momentary Keyswitch
5.4.1 Stay/Instant Disarm (Keyswitch)
SECTIONS [149] TO [156]: FIRST DIGIT = 1
To arm a partition using the Momentary Keyswitch, turn on the
keyswitch for approximately three seconds then turn it off.
Repeating this sequence will disarm the system. The selected
Keyswitch Option (see section 5.4) determines the type of arming.
5.2.3 Maintained Keyswitch
SECTIONS [149] TO [156]: OPTION [4]
When option [4] is enabled, the keyswitch can only disarm
assigned Stay or Instant armed partitions. The Arm Only Option
(see section 5.4.2) must be disabled for this feature to function.
When option [4] is disabled, the keyswitch can disarm partitions
armed using any arming method.
SECTIONS [149] TO [156]: FIRST DIGIT = 2
To arm a partition using the Maintained Keyswitch, turn the switch
from the ON to the OFF position. To disarm a partition set the
keyswitch in the ON position. In the case of an Arm Only option, the
control panel will not perform any action when the switch is in the
ON position. The selected Keyswitch Option (see section 5.4)
determines the type of arming.
5.4.2 Arm/Disarm (Keyswitch)
5.2.4 Generates a Utility Key Event on Open
5.4.3 Stay Arming (Keyswitch)
SECTIONS [149] TO [156]: SECOND DIGIT = 3
When option [3] is enabled, a Utility Key Event will be generated
whenever the keyswitch input is opened (see Table 12 on
page 35). This option can be used to activate or deactivate one or
more of Digiplex’s PGM outputs. When a keyswitch is defined with
the Generate a Utility Key Event on Open option, the Keyswitch
Partition Assignment and Keyswitch Options are disabled. To
program a Keyswitch to generate a Utility Key Event:
1)
2)
Program the Activation Event of a PGM output with the Utility
Key Event corresponding to the desired keyswitch (see PGM
Programming Table in the Programming Guide).
Enable option [3] in the section corresponding to the desired
keyswitch.
18 Reference & Installation Manual
SECTIONS [149] TO [156]:
Option [5] ON = Arm Only
Option [5] OFF = Arm & Disarm
Only one of the arming options (Stay, Force, Instant and
Regular) can be selected.
SECTIONS [149] TO [156]: OPTION [6]
Activating the keyswitch will bypass any zones defined as Stay
Zones (see section 4.4.3 on page 14) in the selected partition. All
other zones will remain activated. For more information on Stay
arming, refer to section 16.1.2 on page 45.
5.4.4 Force Arming (Keyswitch)
SECTIONS [149] TO [156]: OPTION [7]
Activating the keyswitch will arm the selected partition bypassing
any open zones defined as Force Zones (see section 4.4.4 on
page 14) at the time of arming. For more information on Force
arming, refer to section 16.1.6 on page 45.