Download Service Manual - Manuales de Service

DVP3560K
DVP3560K/55
Service Manual
TABLE OF CONTENTS
Page
. Technical Specifications…………....………………………..............1-2
. Safety Instruction, Warning & Notes….……………………....….....1-3
. DFU Instruction..............................................................................2-1
. Mechanical and Dismantling Instructions…………........................3-1
. Software Upgrades and Region Code Change..............................4-1
. Trouble Shooting Chart………………………………………………. 5-1
. Wiring Diagram………………………………………..………..….….6-1
. Electrical Diagrams and Print-layouts..….…………………....….…7-1
. Set Mechanical Exploded view & Part list.…………………..….….8-1
. Revision List..................................................................................9-1
©Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by SL - 952 BU AVM
Version 1.0
Printed in The Netherlands
Subject to modification
CLASS 1
LASER PRODUCT
GB
3141 785 34640
PHILIPS
1-2
(VSHFLÀFDFLRQHV
Nota
‡ /DVHVSHFLÀFDFLRQHV\HOGLVHxRTXHGDQVXMHWRVD
PRGLÀFDFLRQHVVLQSUHYLRDYLVR
USB
‡ Compatibilidad: USB (2.0) de alta velocidad
‡ Clases: UMS (clase de almacenamiento masivo
USB)
Video
‡ Sistema de señal: PAL/NTSC
‡ Salida de video compuesto: 1 Vpp ~ 75 ohmios
‡ Salida de video por componentes:
0,7 Vpp ~ 75 ohmios
‡ Salida HDMI: 480i, 480p, 576i, 576p, 720p,
1080i, 1080p
Audio
‡ Salida estéreo analógica
‡ 5HODFLyQVHxDOUXLGRN+]!G%
(ponderado A)
‡ 5DQJRGLQiPLFRN+]!G%3RQGHUDGR$
‡ ,QWHUIHUHQFLDN+]!G%
‡ 'LVWRUVLyQUXLGRN+]!G%
‡ MPEG MP3: MPEG Audio L3
‡ Salida digital
‡ Coaxial
‡ Salida HDMI
Unidad principal
‡ Dimensiones (An x Al x Pr): 360 x 39 x 209 (mm)
‡ Peso neto: 1,4 kg aproximadamente
Energía
‡ &ODVLÀFDFLyQGHODIXHQWHGHDOLPHQWDFLyQ
110 - 240 V, 50/60 HZ
‡ Consumo de energía: <10 W
‡ Consumo de energía en el modo de espera:
< 0,45 W
Accesorios incluidos
‡ Control remoto y baterías
‡ Cable HDMI
‡ Cables de audio/video
‡ Cable de suministro eléctrico de CA
‡ Adaptador de cable de alimentación
‡ Manual del usuario
(VSHFLÀFDFLyQGHOiVHU
‡ Tipo: láser semiconductor InGaAIP (DVD),
AIGaAs (CD)
‡ Longitud de onda: 658 nm (DVD), 790 nm (CD)
‡ Potencia de salida: 7,0 mW (DVD), 10,0 mW
(VCD/CD)
‡ Divergencia de haz: 60 grados
1-3
Safety instruction, Warning & Notes
Safety instruction
1. General safety
2.Laser safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol
,
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
attention to the following points:
. Route the wires/cables correctly, and fix them with the
mounted cable clamps.
. Check the insulation of the mains lead for external
damage.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
3)
Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4)
Repair
or
correct
unit
when
¡
measurement is less than 1M .
the
resistance
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
This unit employs a laser. Only qualified service personnel
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type
: Semiconductor laser GaAlAs
Wavelength
: 650nm (DVD)
: 780nm (VCD/CD)
Output power
: 7mW (DVD)
: 10mW (DVD /CD)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
beam.
1-4
Warning
1.General
2. Laser
. All ICs and many other semiconductors are susceptible to
. The use of optical instruments with this product, will
electrostatic discharges (ESD). Careless handing during
increase eye hazard.
repair can reduce life drastically. Make sure that, during
. Only qualified service personnel may remove the cover
repair, you are at the same potential as the mass of the
or attempt to service this device, due to possible eye
set by a wristband with resistance. Keep components and
injury.
tools at this same potential. Available ESD protection
with a disc loaded inside the player.
equipment:
1)
. Repair handing should take place as much as possible
Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
. Text below is placed inside the unit, on the laser cover
shield:
4822 310 10671.
2)
Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
Notes:
service
Laboratories. The double-D symbol is trademarks of Dolby
the
player.
Service
personnel
must
take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
Manufactured
under
licence
Laboratories, Inc. All rights reserved.
from
Dolby
1-5
Notes
Lead-Free requirement for service
INDENTIFICATION:
x
Regardless of special logo (not always indicated)
Use only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
One must treat all sets from 1.1.2005 onwards, according
next rules.
companies.
x
Important note: In fact also products a little older can also
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Special information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering
always
use
highest
lead-free
temperature profile, in case of doubt)
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
- lead free BGA-ICs will be delivered in so-called
‘dry-packaging’ (sealed pack including a silica gel
x Use only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste is
pack) to protect the IC against moisture. After
required, please contact the manufacturer of your
opening, dependent of MSL-level seen on
solder-equipment. In general use of solder-paste within
indicator-label in the bag, the BGA-IC possibly
workshops should be avoided because paste is not easy
still
to store and to handle.
communicated via AYS-website.
to
be
baked
dry.
This
will
be
Do not re-use BGAs at all.
x Use only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
has
x
For sets produced before 1.1.2005, containing
o To reach at least a solder-temperature of 400°C,
leaded soldering-tin and components, all needed
o To stabilize the adjusted temperature at the
spare-parts will be available till the end of the
solder-tip
o To exchange solder-tips for different applications.
x Adjust your solder tool so that a temperature around
360°C – 380°C is reached and stabilized at the solder
joint. Heating-time of the solder-joint should not exceed
service-period. For repair of such sets nothing
changes.
x On our website:
www.atyourservice.ce.Philips.com
You find more information to:
~ 4 sec. Avoid temperatures above 400°C otherwise
BGA-de-/soldering (+ baking instructions)
wear-out of tips will rise drastically and flux-fluid will be
Heating-profiles of BGAs and other ICs used in
destroyed. To avoid wear-out of tips switch off un-used
Philips-sets
equipment, or reduce heat.
x Mix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
strongly to avoid mixed
For additional questions please contact your local
solder alloy types (leaded and lead-free). If one cannot
repair-helpdesk.
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
2-1
QSG for DVP3560K/55:
Register your product and get support at
www.philips.com/welcome
DVP3560K
DVD PLAYER DVP3560K
HDMI
1
HDMI OUT
Y Pb Pr & AUDIO OUT
2-2
1
TV OUT & AUDIO OUT
2
2009 © Koninklijke Philips N.V.
All rights reserved.
DVP3560K_55_QSG_V1.0
DVD PLAYER DVP3560K
2-3
Descripción general del producto
Unidad principal
a
‡
Enciende la unidad o pasa al modo de
espera.
‡
Abre o cierra la bandeja de discos.
b
b Compartimiento para el disco
c DISC MENU
‡ Accede o sale del menú del disco.
‡ Pasa al modo de disco.
‡ Durante la reproducción de una
secuencia de diapositivas de fotos,
permite alternar entre el modo de
diversión y el modo simple.
‡ Para VCD y SVCD, activa o desactiva el
control de reproducción PBC (del inglés
Playback Control).
c Panel de visualización
d
DVD PLAYER DVP3560K
a
b
a
‡
d
c d ef g
(Modo de espera encendido)
Enciende el reproductor de DVD o pasa
al modo de espera.
‡
‡
(Abrir/Cerrar)
‡ Abre o cierra la bandeja de discos.
e
‡
(Play/Pause)
Inicia, hace una pausa o reanuda la
reproducción del disco.
‡
e
‡
f Toma
(USB)
‡ Conecta una unidad USB Flash.
f
g MIC
‡ Conexión de micrófono.
/
‡
BACK
Regresa al menú de pantalla anterior.
Pasa al título, capítulo o pista anterior o
siguiente.
g
‡
Pasa al modo de USB.
h Botones numéricos
‡ Selecciona la reproducción de un
elemento.
Control remoto
a
b
c
Navega a través de los menús.
Avanza ( ) o retrocede ( )
rápidamente.
Avanza ( ) o retrocede ( ) lentamente.
r
i SUBTITLE
‡ Selecciona el idioma de los subtítulos en
un disco.
‡ Permite acceder al menú de copia y
eliminación de archivos de audio USB.
j
ZOOM
Ajusta el formato de la imagen a la
pantalla del televisor.
‡ Acerca o aleja la imagen.
‡
d
k
‡
q
e
p
f
g
o
n
KOK RECORD
Graba la voz y la música durante el
NDUDRNHHQXQGLVSRVLWLYRÁDVK86%
l KARAOKE
‡ $FFHGHRVDOHGHOPHQ~GHFRQÀJXUDFLyQ
de karaoke.
m AUDIO/CREATE MP3
‡ Selecciona un canal o idioma de audio en
un disco.
‡ Permite acceder al menú de creación de
archivos MP3.
n
h
‡
Detiene la reproducción.
‡
Inicia, hace una pausa o reanuda la
reproducción del disco.
o
i
m
j
l
k
p
INFO
En discos: permite acceder a las opciones
de reproducción o muestra el estado
actual del disco.
‡ Para diapositivas, muestra una vista en
miniatura de archivos de fotos.
‡
q OK
‡ 3HUPLWHFRQÀUPDUODHQWUDGDRVHOHFFLyQ
r SETUP
‡ $FFHGHRVDOHGHOPHQ~GHFRQÀJXUDFLyQ
3-1
Mechanical and Dismantling Instructions
Dismantling Instruction
Detailed information please refer to the model set.
The following guidelines show how to dismantle the player.
Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1).
Figure 1
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2)
Note: Make sure to operate gently otherwise the guider would be damaged.
Please kindly note that dismantle
the front door
assembly carefully to avoid damage tray and the front door.
Figure 2
3-2
Mechanical and Dismantling Instructions
Detailed information please refer to the model set.
Dismantling Instruction
Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3).
Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 3
Step4: Dismantling Front Panel, disconnect the connectors (XP80 , XP7, XP476), need release 3 snaps of Front Panel & 2 snaps
of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6)
XP476
XP7
XP2
XP1
XP3
XP80
XP4
Figure 4
3-3
Mechanical and Dismantling Instructions
Dismantling Instruction
Detailed information please refer to the model set.
Step5: Dismantling Loader, disconnect the 3 connectors (XP2, XP3, XP4) aiming in the below figure, and remove 1 screw that
connects the loader and the bottom cabinet. (Figure 5)
Figure 5
Step6: Dismantling Main Board, first disconnect the connector (XP1), and then remove 4 screws. (Figure 6)
Step7: Remove the 4 screws on Power Board to dismantle the Power Board. (Figure 6)
Figure 6
4-1
Softeware upgrade and region code change
Preparation to upgrade software
1) Power on the set and open the tray, then press "5""5"
B. Read out the software versions to confirm upgrading
on remote control to check the SW File Name.
2) Start the CD Burning software and create a new CD
project (Data Disc) with the following setting:
Label: DVP3XXX(K) (No need the label name)
1)
2)
SW File Name: DVPXXXX(K)_XX.bin
Note: It is required to keep the SW file name accord.
3) Burn the data onto a blank CDR
Power on the set and press "Setup" button on the
remote control.
Press "1""3""7""9" button or press down cursor
on remote control to select "Preferences" and press
right & down cursor to select "Version Info".
The software version and other informations will be
displayed on the TV screen as follows:
Version
XX.XX.XX.XX (Main version)
Sub-Ver
XX.XX.XX.XX (version of applicaton software)
A) Upgrade software via CDR:
8032
XX.XX.XX.XX
1)
Power on the set and insert the prepared Upgrade CDR.
Servo
XX.XX.XX.XX (software version of Servo)
2)
The set will starts reading disc & response with the
RISC
XX.XX.XX.XX
following display TV screen:
DSP
XX.XX.XX.XX
A.
Procedure for software upgrade:
Upgrade file detected
Region Code
X
Upgrade ?
Press PLAY to start
3)
Press "PLAY" button to confirm, then screen will display:
Upgrade file detected
Do not power off
File Copying
4)
Upgrade file detected
Do not power off
Upgrading
The upgraded tray will automatically open when file
copying completed, then take out the disc.
5)
About 1 minute later, the trace will automatically close
when upgrading completed.
B) Upgrade software via USB Flash Drive:
1)
Create the correct software file onto the USB flash drive.
2)
Power on the set and keep no disc, then insert it to the
USB jack of the front panel.
3)
When the DVD player switchs to the USB state automatically,
pls follow the instructions on the TV screen to confrim the
upgrade operation.
Region Code Change
1) Power on the set and open the tray door;
2) Press the "Setup" button on the remote control, then the
setup interface will be displayed on the TV screen;
3) Move the down cursor on remote control to select "Preferences"
and press "1""3""8""9""3""1" on the remote control;
4) Then move the up or down cursor to select the region code.
Note: Restart after above steps.
Caution: The set must not be power off during
upgrading, Otherwise the Main board will be
damaged entirely.
Trouble shooting chart
5-1
Spindle motor does not move
Motor no move
Go
Check the FFC connection
No
Correct connection
between 24P and the loader.
Yes
Check whether “MO_VCC”
(+5V) voltage
No
Check the MO_VCC power
is normal.
supply
Yes
Check whether laser voltage
No
(1.9V for CD & 2.4V for DVD)
Check/Replace Q5,Q6,Q7,Q8.
on L9 and L10
Yes
1.Whether voltage on pin 15of U20
No
varies between 0 and 3.3V (3.3V for
CD and 0V for DVD),
Check/ Replace U20.
2.Whether peripheral components
are eroded or badly soldered.
Yes
Check opu focus
No
1. Check U20 pin17 FOCUS_PWM signals
2.If there are F+, F-, T+ and T- signals output
from U2.
Yes
Check/Replace the loader
FOCUS_PWN waveform
Trouble shooting chart
5-2
The power can not be on or off
The power can’t be
on or off
Go
Check the power supply
No
on the power board is
Repair the power board
normal.
Yes
Check if the XS301 on the
front board to XP5 on the
Yes
No
Check/Correct connection
decoder board is in good
contact.
Yes
Whether the connection
No
to K303 is broken.
Correct the connection
Yes
Whether there is 0V and
3.3V voltage difference on
Pin 39 PCON of U20.
Yes
No
Replace U20.
5-3
All output voltages on the power board is 0V or deviated.
Trouble shooting chart
All output voltages on
the power board is 0V or
deviated
Yes
Check whether
Yes
Replace F1
F1 is blown
No
Check whether there is
Replace C1&C2 if D1, D2, D3, D4 are
No
normal.
300V on C1 or C2.
Yes
Check whether 100KHz
oscillating signal on
Pin6 of U20
No
Check/ replace U20.
U1(PIN 3 - RC waveform)
U1(PIN 8 - Drain waveform)
Yes
Check if +5V and +12V are
short.
Yes
Check whether the components in the
short-circuit voltage are defected or eroded.
No
Check whether U20 are eroded.
Trouble shooting chart
5-4
Disc cannot be read.
Disc cannot be read.
Yes
Check the FFC connection
No
Check the loaded circuit
between 24P and the loader.
Yes
1.Check voltage on pin 15 of U20 varies
Check whether there is laser
voltage (1.9V for CD and 2.4V for
No
between 0 and 3.3V:
Æ3.3V for CD
Æ0V for DVD
DVD) on L9 and L10.
2.Check whether peripheral components
are eroded or defect
Yes
Check
U20,
peripheral
U2,
components
and
No
are
Re-solder or replace the defective parts
eroded or badly soldered.
Yes
Check if there is RFO signal on
pin17 of XP2. (The normal RFO
No
Check U20 and peripheral components
signal is a clear reticulated wave)
Yes
Check the connection
between U20
Yes
Replace U20 or loader.
No
Correct connection
Trouble shooting chart
5-5
Only DVD disc or only disc except DVD can be played
Only DVD disc, or only disc
except DVD can be Played.
Go
Check
the
FFC
connection between
24pin and the loader.
No
Check the loaded circuit
Yes
Check
laser
voltage
(2.4V)
Check the solder status on U20 and
No
output on L10, if pin10 of U20 is
peripheral components
at low level.
Yes
No
Check whether there
is voltage variance on
pin 17 of U20.
check if bad solder exist on U20 and
peripheral components
Yes
Check whether pins of U20
No
and peripheral components
are badly soldered, defected
Replace the bad spare parts
Yes
Check Q5, Q7 whether
in good condition
Yes
Change U20 or the loader.
No
Correct connection
Trouble shooting chart
5-6
No display on LED, and buttons do not work
No display on LED, and
buttons do not work
Yes
Check whether there is
correct
contact
between
No
Correct connection
XS301 and XP5
Yes
Check VCC(+5v) voltage
on the power and front
No
board
Fix power supply board top a
power supply for should
electric circuit
Yes
Check there are STB, SDA
and SCK signals on XS301
on the front board.
No
Check the U20’s pin 36,37,38
arrive the XP5 connect condition
XP5 (PIN 1 CLK)
XP5 (PIN3 DOUT)
Yes
1.Check whether bad solder exists on
U301 and pins of LED,
2.Check whether the circuit connected to
K302, K303 and K301 is broken,
3.Check whether R300, R301 and R302
are open-circuit.
Yes
Replace U301 or LED
No
Correct connection
5-7
Distorted audio and loud noise
Distorted audio and
loud noise
Yes
Check the power supply
voltages +12V to the
operation amplifying Q3 is
normal.
No
Check Q3
Yes
Check whether the muting
transistor R167ˈR152 are
No
Replace R167ˈR152
normal
Yes
Check whether the muting
transistor
normal
Q48,Q50,
No
are
Replace Q48,Q50,
Yes
Checking the U12 leads
No
the feet has no to break to
open
Correct connection
Yes
Check the voltage on
No
pin3 or pin5 of U12 is OK
(Should be 2.5~3.1V)
Replace R76, CE38, C152
Yes
Check whether the U1 or
U12 powersupply normal
Yes
Replace U20
No
Check U12
Trouble shooting chart
Trouble shooting chart
5-8
Abnormal color of video picture
Abnormal color of
video picture
Yes
Check
whether
the
No
Check Y2, R20,R27,C22 and C23
27MHz output signal
Yes
Check whether the 3.3V
and 1.8V power supply
voltages on the decoder
board are normal.
No
Check other of power supply electric
circuit
Yes
Check whether the
video filter network
circuit is normal.
No
Correct the connection
Yes
Check if the video signals on Pin
98,100,101,102, of U1 are normal
No
Change U20
Trouble shooting chart
5-9
Remote reception is insensitive or fails.
Remote reception is
insensitive or fails.
Go
Check if the remote
control works properly.
No
Check battery
Yes
Check if the power supply
voltage to the remote censor
is normal
No
Check
R315ǃC315
Yes
Use an oscilloscope to check if there
No
is output waveform from the first pin
REM301(PIN1 - RC waveform)
IR of the remote censor after pressing
button on the remote control.
Yes
Check if there is IR
signal on pin 33 of U20
Yes
Change U20
IR waveform
No
Correct connection
Trouble shooting chart
5-10
No video picture, no sound.
No video picture,
no sound.
Check whether all the voltages
No
Check the loaded circuit
from the power board to the
CVBS(R21 point) waveform
decoder board are normal.
Yes
Check if the reset circuit consisting
ofCE7, D2 is normal (at a low level
for
tens
of
milliseconds,
No
Change CE7, D2.
then
constantly at 3.3V).
27Mhz waveform
Yes
Check whether there is
27MHz signal output.
Crystal oscillator Y2 and
No
peripheral components
are defected or eroded.
Yes
Check if there is 128MHz
Check whether
short-circuit or bad
solder on U4,U5ˈU8ˈ
U7
No
signal output on R67.
SDRAM(R67 DCLK) waveform
No
Yes
Check if short-circuit and
bad solder exist on Pin
98
Check U20.
No
Yes
Reconnect the component in
Yes
6-1
6-1
A
B
C
D
MT1389G 128 PIN GPIO LIST
DVP3560K WIRING DIAGRAM
E
E
NAME
COAX
Y
R
VR_CD
TRAY_CLOSE
15
VR_DVD
FG / GPIO2
18
TRIN
UP1_6
28
HDM_SCL
29
HDMI_SDA
GPIO3
HDMI
Pb
CVBS
L
P5
P1
ASA F8829 + SANYO DV38
AUDIO
AMP&LPF
VIDEO LPF&DRIVE
24
XP2
24PIN*0.5
1
XP1 5PIN*2.5
U20
6
1
LOAD+
LOADTROUT
GND
TRIN
C
16M
FLASH
XP3
5PIN*2.0
XP7
4PIN*2.0
10
1
1
4
1
XS302
2PIN*2.0
5
1
USB_DM
USB_DP
GND
VCC_USB
XS601
1
U_CEC
34
GPIO4
35
VSCK
GPO5
7
TRCLOSE
GPIO6
31
TxD
GPIO7
39
PCON
GPIO8
38
POWER_K
GPIO9
37
VSDA
GPIO10
81
HPD
GPIO11
30
RxD
GPIO12
80
SPDIF
GPIO13
36
VSTB
GPO14
96
AUDIO_MUTE
GPIO19
103
STANDBY_LED
D
GPIO20
104
AVCM
GPIO21
105
AKIN1
ARF
109
AUDIO_ARF
ARS
110
AUDIO_ARS
ALS
114
AUDIO_ALS
ALF
115
AUDIO_ALF
GPIO34
107
TROPEN
GPIO35
108
STBY
RFIN / OPOUT
120
LIMIT
3
+12VA
GND
MIC
STANDBY_LED
POWER_K
GND
VSCK
VSTB
VSDA
GND
5V
IR
DV33
10
1
GND
POWER-K
LED+
LED-
XS201
5PIN*2.5
E
5
XP6
3PIN*2.0
MAIN BOARD
MP-1
4
SWITCH
XS303
BOARD 4PIN*2.0
1
U176
XP5
10PIN*2.0
5
+5V
+5V
GND
+12V
GND
POWER
SUPPLY
AM5888S
U10
SPS+
LIMIT
GND
SLSL+
40-D89G2U-MA*2G
MOTER
DRIVER
1
1
64M U186
SDRAM
MT1389G
6PIN*2.0
XP4
DVD LOADER
D
P2
FEATURES
14
UP1_7
Pr
PIN
TRAY_OPEN
7PIN*2.0
XS301
10PIN*2.0
1
7
LED/KEY&LEDˇET6202
USB+OK BOARD
40-P3380K-KUD2G
4
VIDEO/YUV
LDSW
TROUT
98
V_CVBS
102
V_R/V
101
V_B/U
V_G/Y
100
B
C
AR
111
AR
AL
113
AL
A
B
A
A
B
C
D
E
7-1
7-1
5
4
3
Front Board Circuit Diagram:
VCC
2
1
U5V
R315
REM301
5
)5200$,1%2$5'
4
5
4
VCC
GND
IR
3
2
1
100 ohm R318
100R/NC
IR
+
REM
for dvp352x
IR
VCC
GND
DATA
CS
CLK
U5V
1
2
3
4
5
6
7
8
9
10
C306
0.1u
C315
47p
XS301
D
R320
VCC
0R
1
2
3
4
LED+
LEDPOWER_K1
POWER_K
U5V
STB_LED
XS302
CON4(2.0)
CE301
47uF
C316
100p
IR
DATA
CS
CLK
C307
100p
D
C308
100p
VCC
R319
POWER_K
STB_LED
5VL
R303 R304 R305
0 ohm
LED-
CON10(2.0)
R306
4K7
DATA
CLK
CS
R300
R301
R302
4K7
51K
4K7
100
100
100
R307
R308
10K
10K
C300 C301 C302
C
100P 100P
R317 33R
R309
R310
5VL
0.1u
1K
1K
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
100P
C303
U301
ET6202
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CE300
+
OSC
DI/O
CLK
STB
KEY1
KEY2
VDD
SEG1/KS1
SEG2/KS2
SEG3/KS3
SEG4/KS4
SEG5/KS5
SEG6/KS6
SEG7/KS7
LED1
GRID[1:7]
GND
GRID1
GRID2
GND
GRID3
GRID4
GND
VDD
SEG14/GRID5
SEG13/GRID6
SEG12/GRID7
SEG10/KS10
SEG9/KS9
SEG8/KS8
28
27
26
25
24
23
22
21
20
19
18
17
16
15
GRID1
GRID2
GRID3
GRID4
GRID5
GRID6
GRID7
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
GRID1
GRID2
GRID3
GRID4
VCC
GRID7
GRID6
GRID5
LED+
R316 33R
1
2
3
4
5
6
7
8
9
10
11
12
13
GRID1
GRID2
GRID3
GRID4
GRID5
GRID6
GRID7
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
C
JDD350501AG
47uF
SEG[1:6]
KEY1
KEY2
K301
1N4148
D301
1N4148
D302
R312
K302
open/close
play/pause
1K
R311
1K
KS2
POWER_K
R313
0R
POWER_K1
B
B
R314
0R/NC
C304
100p
R311
C305
100p
R313
R314
0.3W
N
N
Y
1W
Y
Y
N
A
A
5
4
3
2
1
7-2
7-2
A
B
C
D
E
Switch Board Circuit Diagram:
1
1
K303
1
2
3
4
2
POWER
2
LED3
XP1
CON4(2.0)
C319
47p
SWITCH
C317
47p
C318
47p
BOARD
3
3
4
4
A
B
C
D
E
7-3
7-3
1
2
3
4
5
OK Board & USB Board Electric Diagram
12V
R210
12VA
150
CE201
22uF
C201
REF
22K
0.1u
A
CE200
22uF
R203
22K
C205
47p
R205
180K
R211
C203
U200A
B
C211
100K
1
NJM4558
2.2uF
1000p
REF
12VA
C208
100p
5
+
6
-
C204
100p
R206
C
20K
P600
USB
47-USB003-XX2
USB
1
2
3
4
5
6
MGND
MGND
VCC
SGND
MGND
L200
USB_DN
USB_DP
L201
U200B
R207
100K
C206
47p
C
R208
MIC_OUT
MIC
12V
1K
VCC
SGND
USB_DN
USB_DP
680
1
2
3
4
5
6
7
D
AGND
8PIN/2.0mm
XP601
500Z
MGND
MIC_OUT
C209
2.2uF
R209
D
NJM4558
7
4
ĭ3.5mm
3
8
R200
10K
2.2uF
2
8
5.6K
C210
4
R201
1
2
3
+
KARAOKE
B
47-EAR024-XX0
P601
KARAOKE INPUT
R202
12VA
-
A
AGND
500Z
MGND
L202
SGND
500Z
E
E
1
2
3
4
5
7-4
7-4
A
B
C
D
E
Power Board Circuit Diagram:
1
1
* CAUTION :
THE PARTS MARKED WITH
ARE IMPORTANT PARTS ON THE SAFETY.
PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL.
F501
T2AL/250ac
TR501
NTC 10
1
P501
+
RV501
+
+
2
2
CX501
CON502
10K471
AC INPUT
D502
1N4007
L501
680uH
0.1uF/275Vac
C501 +
D504 (10uF)22uF/400V(250V)
C502 +
1N4007
(10uF)22uF/400V(250V)
D503
1N4007
1
1
AC INPUT
1
+
AC INPUT
CN501
D501
1N4007
L503
20mH
P502
2
FB501
FB
7
2
T501
6
CON503
C504
152/1KV
R502
R503
1/4W120K 1/4W120K
FR102
4
D507
IN4007
R15
D506
5
8
1/6W 10K
10
3
+
C509
10uF/16V
+
C512
10uF/50V
D508
FR102
C513
0.1uF/63V
+
D509
L502
6.8uH
1
9
EN/UV
C507
2200uF/10V
+
C508
470uF/16V
R505
1/6W12K 1%
R509
1/6W100
1/6W100k
1
R513
4
S
S
7
S
6
S
5
3
8
2
3
NC
BP/M
Drain
4
+
U1
TNY177PN
1/6W10k
SR360
11
1
C505
GND
+12V
GND
+5V
+5V
5X2.5 HEADER
2
R5061/6W 680
R504
47uF/25V
R516
1/6W10k
5
4
3
2
1
R508
1/6W1k
R510
1/6W10k
3
C511
0.1uF/63V
3
2
3
U502
PC123X92
1
R507
1/6W11.3k 1%
2
U503
AZ431
CY501
102/400Vac
4
4
* No use the Class 1 environment management materials of SS-00259
* All of moulding resinous, ink, paint and coating electric wire must be ordered from designated GP supplier of SONY
A
B
C
D
E
7-5
7-5
A
B
TO POWER BOARD
XP1
5pin/2.5mm
C
D
Main Board Circuit Diagram: POWER SUPPLY
MO_VCC
+5VD
+5VP
GND
+P12V
1
2
3
4
5
L1
960mA
FB AXIAL
DV33
R10
C112
0.1uF
C1
0.1uF
NC/0
VCC
Q10
SS8550
VCC
R113
4.7K
+12V: +12V(+-10%)
1
E
C77
1uF
+5V: +5V(+-2.5%)
Q3
SS8550
C109
0.1uF
C111
0.1uF
R13
22K
R14
1.3K
DV33
R50
VSDA
VSTB
VSCK
POWER_K
STANDBY_LED
+12V
100mA
C12
0.1uF
R115
4.7K/NC
DV33
TO FRONT PANEL
R118
4.7K/NC
10PIN/2.0mm XP5
IR
R58
2.2K
+12V
R120
4.7K/NC
PCON
R12
4.7K
R51
R52
R53
R99
R109
10
9
8
7
6
5
4
3
2
1
100
100
100
100
1K
1K
STANDBY_LED
C44
C45
NC(47pF)
NC(47pF)
C81
C42
C43
NC(47pF)
100pF 100pF
C82
100pF
C46
NC(100pF)
R29
PCON
R33
4.7K
URST#
MO_VCC
C25
NC(0.1UF)
USBPC
R22
4.7K
1
OFF-PAGE CONNECTION
SD33
VCC
DV33
RFV33
89M_3V3
2
VSDA
RFV33
0/FB500
CE23
47uF/6.3V
+
VSTB
C73
0.1uF
IR
810mA
D30
RL207
370mA
440mA
R48
1R/1W
USBPC
100uF/16V
3
TR_B1
C4
3
(3)
VSCK
3
VSDA
3
3
AADVDD
2
3
3
3
POWER_K
3
USBPC
3
V12
DV33
R97
0R/5.1K 1%
+
CE4
220uF/16V
C108
0.1uF
AUDIO ADC
R95
20K 1%
+ CE5
0.1uF
3
3
89M_3V3
Q16
SS8550
AADVDD
4.7/0603
Q17
SS8550
TR_B2
+ CE6
AADVDD
RFV33
4.3R/2W
3
R6
(2,3,4,7)
R40
SD33
C76
0.1uF
DV33
PCON
POWER_K
C75
0.1uF
FB6
500
(2,3,6,7)
IR
AADVDD
CE24
47uF/6.3V
4
VCC
MO_VCC
89M_3V3
+
(2,3,6)
SD33
VSTB
PCON
FB1
500
MO_VCC
V12
VSCK
RFV33
R8
(3,4)
Q2
BT3904
1K
V12
DV33
URST#
+
REGO2
CE3
220uF/16V
47uF/16V
3
3
R98
NC/10K 1%
REGO1
R96
12K 1%
3
C107
0.1uF
RESET Circuit
DV33
R15
15K
R19
22K
R18
3.3K
R17
R16
4.7K
URST#
3.3K
Q21
1N4148/NC
D2
Q22
2N3904
2N3904
R26
URST#
1K
+
CE7
22uF/16V
CEL5-5
C21
1uF
4
4
A
B
C
D
E
7-6
7-6
A
0.1uF
SP-A
R28
D3
BAT54C
2
RFV12-2
R127 0
OPO
10K
0.1uF
RFV12-1
R126 0
3
+
0.1uF
RFV33
SERVO RF DeCAP.
1
SP-A
SP+
R128
10K LIMIT
R23
0.01uF
XP4
6PIN/2.0mm
1
2
3
4
5
6
1K
SLSL+
V20
C71
+
0.1uF
C36
C34
C48
0.1uF
0.1uF
DQM[0..1]
BA[0..1]
Crystal
CE8
47uF/6.3V
+
0.1uF
R20
CE9
47uF/6.3V
C28
CE2
R27 51
27MHz
XO
C31
NC/15pF
SF_CK
SF_CS
SF_DI
SF_DO
Put these circuits as
closer as possible to
MT1389
CVBS_OUT
V_R
V_B
V_G
STBY
2SK3018
SC-70
XI
2
R200
R1
VCC
0.1uF
C6
0.1uF
100uF/16V
100
R60
NC/0R
89M_3V3
C3
FB3 0R 0.1uF
LD-DVD
C7
10uF/10V
R3
Very Important to
reduce Noise
V12
FB4
MDI1
LD-CD
5.1K 1%
C8
10uF/10V
0.1uF
C78
NC/0.1uF
0.1uF
L10
10uH
L9
10uH
NC
LDO2
Q7
CE11
27
28
R45
4.7
R46
4.7
Q23
47uF/6.3V
9012
R49
10K
D4
1N4148
Q24
47uF/6.3V
R32
R41
R42
R43
R44
C38
TP11
SL+
SLR54
10K
R55
10K
30
G2
22
23
24
25
26
27
28
FMSO
C95
VOTK+
VOTKVOLD+
VOLDVCC2
NC
VCTL
TR_B2
TRSO
V1P4
STBY
0.1uF
GND
VINLD
NC
TRB2
VINTK
BIAS
MUTE
VOFC+
VOFCVOSLVOSL+
VOTR+
VOTRVCC
14
13
12
11
10
9
8
G1
29
REV
FWD
REGO1
VINSL+
REGO2
TRB1
VINFC
7
6
5
4
3
2
1
89M_3V3
SPSP+
LOAD+
LOAD-
TROPEN
TRCLOSE
R56
FOSO
TP16
TP17
10K
TP13
TP15
C96
10K
0.1uF
AR
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
TXC+
TXC-
C40
27k
27k
15k
10k
MT1389G
MT1389M
2.5K 1%
0.015uF
C11
0.1uF
MO_VCC
C85
C86
C87
0.1uF
0.1uF
0.1uF
C91
C92
0.1uF
0.1uF
0.1uF
REGO1
DMSO
REGO2
TR_B1
+ CE15
220uF/16V
C49
0.1uF
R62
10K
TROUT
R63
10K
TRIN
C18
0.1uF
R9
R11
LOADLOAD+
1K
1K
XP3
5PIN/2.0mm
1
2
3
4
5
C80
4.7uF
R114
89M_3V3
1K
C133
10uF/10V
V1P4
R31
180
R59
180
DV33
AADVDD
V12
RFV33
MO_VCC
R102
NC/4.7K
XP8
B
7
7
TX1+
TX1-
7
7
TX2+
TX2-
7
7
HPLG
7
2
7
C10
C2
NC(100pF) NC(100pF)
RXD
TxD
GND
1
2
3
4
4pin/2.0mm
RXD
GPIO6
TXD
(2,3,4,7)
AADVDD
2
89M_3V3
1
V12
RFV33
(2)
1
2
(2,3,7)
3
IR
IR
2
TR_B1
2
REGO1
REGO2
PCON
VSTB
USBPC
(2,4)
DV33
Power
TR_B2
GPIO11
URST#
VCC
USBPC
2
TR_B2
2
REGO2
2
PCON
2
VSCK
2
VSDA
2
VSTB
2
USBPC
2
POWER_K
2
XP7
4PIN/2.0mm
4
C74
0.1uF
U3
C
7
7
TX0+
TX0-
MO_VCC
VCC
1
2
3
4
USB_DM
USB_DP
TXC+
TXC-
89M_CEC 7
3
VCC_USB
PRTR5V0U2X
A
6
6
UP1_[6..7]
VSDA
4
6
ASPDIF
AKIN1
89M_CEC
POWER_K
MotorDriver
AUDIO_MUTE
URST#
R101
NC/4.7K
MO_VCC
1
6
6
HPLG
Front
2
AR
AL
TMDS I/F
Default
0.1uF
5
5
5
5
TX2+
TX2-
REGO1
C19
CVBS_OUT
V_R
V_B
V_G
89M_3V3
NC(100pF)
Q9
PBSS5320T
DV33
4
4
4
4
UP1_[6..7]
[FUSE(500MA)]
C90
SF_CK
SF_CS
SF_DI
SF_DO
TX1+
TX1-
Q1
NC(CES2302)
3
2
MO_VCC
F1
V12
1
TXC+
TXC-
V12
RS-232
FOO
TRO
FMO
DMO
C41
4
4
4
4
TX0+
TX0R5 2.2R
R4
HPLG
ASPDIF
RAS#
CAS#
WE#
MA4
MA5
MA6
V12
DV33
V12
Chip Decap.
AM5888
R61
TX0+
TX0-
MA3
MA2
MA1
MA0
MA10
BA1
BA0
0R
C13
0.1uF
VSCK
U2
4
C39
330pF 330pF 0.1uF
TP10
FB2
TX1+
TX1-
TR_B1
FOSO
TRSO
FMSO
DMSO
+ CE33
100uF/10V
4
DCLK
RAS#
CAS#
WE#
AUDIO I/F
10K
FF+
15
16
17
18
19
20
21
AUDIO_MUTE
0.1uF/NC
3V3
89M_3V3
LDO1
TP9
C14
9012
9012
TT+
GPO14
DACVDD3
TX2+
TX2-
C16
33K
4
BA[0..1]
89M_3V3
RFV33
R57
+ CE12
Q8
TP8
V1.0
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
RFV33
9012
C79
LQFP 128
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
C37
MT1389G
AUDIO_MUTE
ASPDIF
AKIN1
VREF / GPO14
DACVDDC
TX2P
TX2N
AVDD12_D
TX1P
TX1N
AVSS12
TX0P
TX0N
AVDD12_C
TXCP
TXCN
AVDD33_12
EXT_RES
GPIO10 / HPLG
SPDIF / GPIO12
DVDD12
RA3
RA2
RA1
RA0
RA10
BA1
BA0
DVDD33
RAS#
CAS#
RWE#
RA4
RA5
RA6
VCC_USB
F
B
A
RFO
IOA
D
C
TT+
F+
F-
AVDD12_2
AVDD33_1
XTALI
XTALO
V20
V14
REXT / GPO5
MDI1
LDO1
LDO2
AVDD33_2
DMO
FMO
TRAY_OPEN
TRAY_CLOSE
TRO
FOO
FG / GPIO2
USB_DP
USB_DM
VDD33_USB
PAD_VRT / GPIO37
VDD12_USB
SF_CS_
SF_DO
SF_DI
SF_CK
UP1_6 / SCL
UP1_7 / SDA
GPIO11
GPIO6
PRST#
IR
GPIO3
VSCK
VSTB
VSDA
POWER_K
PCON
E
AVCC1
V20
C94
MO_VCC
USB_V12
SF_CS
SF_DO
SF_DI
SF_CK
UP1_6
UP1_7
GPIO11
GPIO6
URST#
0R
C9
NC/0.1uF
TP12
TP14
XO
V20
V1P4
GPO5
MDI1
LDO1
LDO2
AVDD33
DMO
FMO
PIN_14
PIN_15
TRO
FOO
TRIN
USB_DP
USB_DM
USB_V33
15K/NC
C5
4.7uF
+ CE10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
GPO14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQM1
DCLK
MA11
MA9
MA8
MA7
100
51
89M_3V3
+
TOP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
C32
R39
25
26
XP2
SMD0.5 TOP
R38
L6
FB
VR_CD
VR_DVD
SONY 313
3
RFV12-2
RFVDD3
1S
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQM0
DQ15
DQ14
2
129
TROPEN
1
3
G
IOA
GPIO35
AR
AL
RFF
RFE
RFD
RFC
RFB
RFA
RFH / OPINN
RFG / OPINP
RFIN / OPOUT / GPI36
RFIP
AVDD12
ADACVDD2
ADACVDD1
CENTER / GPIO
ALS / GPIO
AL / GPIO
AVCM
AR / GPIO
ARS / GPIO
LFE / GPIO
PAD_APLLCAP / GPIO35
APLLVDD_GPIO / GPIO34
AADVDD
AKIN1 / GPIO21
ADVCM / GPIO20
AKIN2 / GPIO19
R
B
G
DACVDDB
CVBS
FS
GPIO34
D
U20
89M_CEC
DQM[0..1]
VIDEO I/F
R108
560
VR_DVD
GPIO3
E-PAD/GND
PIN_15
V_R
V_B
V_G
DACVDD3
CVBS_OUT
VR_CD
GPIO35
GPIO34
AADVDD
AKIN1
ADVCM
PIN_14
AL
TRCLOSE
ADACVDD
C29
1uF
TROUT
E
F
D
A
B
C
OPOPO
GPI36 220pF
C30
RFV12-1
LIMIT
GPO5
4
S-FLASH
IR
GPIO3 / INT#
GPIO4
GPIO13
GPIO9
GPIO8
GPIO7 / CKE
DVDD33
RD0
RD1
RD2
RD3
RD4
RD5
RD6
RD7
DQM0
RD15
RD14
DVDD12
RD13
RD12
RD11
RD10
RD9
RD8
DQM1
RCLK
RA11
RA9
RA8
RA7
GPI36
4
MA[0..11]
DRAM I/F
C23
33pF
0R/FB500R
10uF/10V
RFO
RF Reference
DCLK
RAS#
CAS#
WE#
100K
Y2
XI
V1P4
C72
DQ[0..15]
MA[0..11]
C22
FB10 33pF
C20
0.1uF
DQ[0..15]
2200pF
4.7uF
DV33
RFVDD3
C35
RFV33
OFF-PAGE CONNECTION
R21
0
DACVDD3
C84
C83
0.1uF
0
10uF/10V
0.1uF
C27
R30
E
C17
C15
0.1uF
ADACVDD
C33
V12
DV33
CE1
1
1
10uF/6.3V
C24
C93
OP-
10K
D
89M_3V3
470uF/10V
R24
R25
C
+
SP-
B
Main Board Circuit Diagram: MT1389G
D
E
7-7
7-7
A
B
C
D
E
Main Board Circuit Diagram: SDRAM & FLASH
SDR_DRAM (Dual Layout)
U4
1
SD33
DCLK
R65
10K
SDCKE
R66
10K
DCS#
R67
SDCLK
C51
47
NC/5P
BA0
BA1
R68
R69
DBA0
DBA1
33
33
RAS#
R202
0
CAS#
WE#
R203
R204
0
MA0
MA1
MA2
MA3
MA4
MA5
MA6
MA7
MA8
MA9
MA10
MA11
DBA0
DBA1
23
24
25
26
29
30
31
32
33
34
22
35
20
21
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
BA0/A13
BA1/A12
SDCLK
SDCKE
38
37
CLK
CKE
DCS#
DRAS#
DCAS#
DWE#
19
18
17
16
CS
RAS
CAS
WE
DQM0
DQM1
DRAS#
DCAS#
DWE#
0
15
39
DQML
DQMH
36
40
NC
NC
54
41
28
VSS
VSS
VSS
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
1
OFF-PAGE CONNECTION
DQ[0..15]
MA[0..11]
DQM[0..1]
BA[0..1]
SD33
VCC
VCC
VCC
1
14
27
VCCQ
VCCQ
VCCQ
VCCQ
3
9
43
49
VSSQ
VSSQ
VSSQ
VSSQ
6
12
46
52
DCLK
RAS#
CAS#
WE#
SD33
SF_CK
SF_CS
SF_DI
SF_DO
SD33
SerialFlash
R73
3
BA[0..1]
3
DCLK
RAS#
CAS#
WE#
3
3
3
3
SF_CK
SF_CS
SF_DI
SF_DO
3
3
3
3
DV33
(2,3,4,7)
SD33
2
2
Power
URST#
FV33
3
DQM[0..1]
S-FLASH
DV33
SF_CS
SF_DO
10K
3
DRAM I/F
ESMT M12L64164A/N.C
2
DQ[0..15]
MA[0..11]
FV33
U5
1
2
3
4
8
7
6
5
CE# VDD
SO HOLD#
WP# SCK
VSS
SI
SF_CK
SF_DI
(2,3,4)
DV33
R72
10K
FV33
C54
AT25FS040/EN25B80
URST#
0.1uF
R47
0/68
R132
NC/68
FV33
4M/8M bit
FV33
R74
10K
SF_CS
R75
R131
NC/10K
3
R129
NC/15K
10K/NC
NC/2SK3018
Q25
R130
NC/3.3K
SD33
3
1
2
Q26
NC/2N3904
C97
C98
C99
C100
0.1uF
0.1uF
0.1uF
0.1uF
3
4
4
A
B
C
D
E
7-8
7-8
A
B
C50
75 1%
100pF
E
R/V_O
0R/1.8uH
R64
D
Main Board Circuit Diagram: VIDEO OUT & AV-CONNECTOR
L11
V_R
C
OFF-PAGE CONNECTION
1
1
CVBS_OUT
L12
V_B
B/U_O
0R/1.8uH
R70
C52
75 1%
100pF
V_R
V_B
V_G
CVBS_OUT
3
V_R
V_B
V_G
3
3
3
VIDEO I/F
U11
R/V_O
B/U_O
1
6
2
5
3
4
CVBSO
G/Y_O
PESD3V3L5UY/NA
L13
V_G
G/Y_O
0R/1.8uH
R71
C53
75 1%
100pF
2
2
R76
0R
L14
CE16
0R/1.8uH
470uF/6.3V/NC
CVBSO
+
CVBS_OUT
R77
C55
75 1%
100pF
P1
RCA/VIDEO OUT
D6
D7
3
D8
2
2
2
D5
1
47pF
2
C59
47pF
1
C58
47pF
1
C57
47pF
1
3
C56
RCA
47-RCA150-XX1
1
2
3
4
5
6
CVBSO
G/Y_O
B/U_O
R/V_O
4
4
A
B
C
D
E
7-9
7-9
A
B
C60
4
R81
5.1K
2
refa
9012
8
NJM4558 OPA
1000pF
1
R82
LCH
470
R83
10uF/16V
+12VA
A_MUTE
AL
AR
(Power on MUTE)
CE18
1
+
C64
3
Q13
U6A
-
10K 1%
E
OFF-PAGE CONNECTION
MO_VCC
100pF
+
30K 1%
R80
D
Main Board Circuit Diagram: AUDIO OUTPUT
R78
AL
C
470
4.7K
C65
100K
R84
AL
AR
3
3
R100
NC/1000pF
R133
Q11
2N3904
10K
R137
3.3K
R85
AUDIO_MUTE
CE27
ASPDIF
AKIN1
A_MUTE
Q14
AUDIO_MUTE
3
ASPDIF
AKIN1
3
3
1
9012
+
220uF/16V
(Power off MUTE)
AUDIO I/F
30K 1%
4
5
U6B
1000pF
3
ASPDIF
ASPDIF
R92
+
7
NJM4558 OPA
R88
R93
10uF/16v
R94
470
100
C68
AUDIO_MUTE
NC/1000pF
R149
4.7K
Q12
2N3904
(2,6,7)
Q15
R171
22K
AKIN1
COAXIAL
C61
0.1uF
R79
100
MIC
+12VA
0.1uF
C62
C101
C63
3300pF
0.1uF
100pF
XP6
3PIN/2.0mm
1
2
3
2
OPTICAL
33
P2
RCA/AUDIO OUT
+12VA
refa
33K
R87
CE19
10K
100uF/16V
LCH
RCH
C47
+
0.1uF
VCC
OPTICAL
R110
22/NC
CE28
47uF/16V/NC
+12V
R134
1
2
3
4
5
6
7
8
9
COAXIAL
100
CE36
100uF/25V
+
C155
0.1uF/NC
RCA+OPTICAL
R86
3
2
MO_VCC
BT3904
100pF
R119
VCC
POWER
C70
100k
C67
R89
100
MO_VCC
RCH
470
+12VA
A_MUTE
2
VCC
4.7K
CE21
8
C69
6
+
refa
-
10K 1%
100pF
R147
R91
5.1K
R90
AR
C66
C114
NC
3
+12VA
C103
0.1uF
4
4
A
B
C
D
E
7-10
7-10
A
B
C
D
E
Main Board Circuit Diagram: HDMI I/F
OFF-PAGE CONNECTION
1
1
DV33
VCC
MO_VCC
DV33
(2,3,4,7)
VCC
(2,3,7)
MO_VCC
Power
TXC+
TXC-
TX2+
TX2TX1+
TX1TX0+
TX0TXC+
TXC-
89M_CEC
R103 0 CEC
HDMI_SCL
HDMI_SDA
2
47K
HPLG
DV33
R201
27K
FB19
MO_VCC
FB500R
TX0+
TX0-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
TX1+
TX1TX2+
TX2HPLG
UP1_[6..7]
TXC+
TXC-
3
3
TX0+
TX0-
3
3
TX1+
TX1-
3
3
TX2+
TX2-
3
3
HPLG
3
UP1_[6..7]
89M_CEC
3
89M_CEC 3
TMDS I/F
20
21
R165
23
22
Differential Signal !
No through hole & length less than 5cm !
100 ohm - Impedance
P3
HDMI TYPE-A
HDMI_TYPE_A
2
HDMI_VCC
C104
0.1uF
D50
+
CE37
10uF/16V
1N4148
MO_VCC
CEC
R104
C105
1.5K
0.1uF
R105
1.5K
HDMI_SCL
R106
0R UP1_6
HDMI_SDA
R107
0R UP1_7
C106
C113
0.1uF
0.1uF
3
3
4
4
A
B
C
D
E
7-11
Front Board & Switch Board Print-layout (Bottom side):
7-11
7-12
OK Board and USB Board Print-layout (Top and Bottom side):
7-12
7-13
Power Board Print-layout (Bottom side):
7-13
7-14
7-14
Main Board Print-layout (Top side):
7-15
7-15
Main Board Print-layout (Bottom side):
8-1
Exploded view for DVP3560K/55:
It is a general mechanical exploded view for DVP3560K/55, pls refer to the model set
for detailed information.
ASSY1 includes components:1.3.4.5.21
8-2
DVP3560K/55 SERVICE PARTLIST
ELECTRICAL PARTLIST
No
12NC No.
ASSY-KU BD COMPONENT PARTLIST
Description
Q'ty
NO
12NC NO.
Description
Q'ty
9
996510031366
ASSY-MAIN BOARD
1
16
996510031358
ASSY-POWER BOARD
1
19
996510020951
ASSY-KU BD
1
ASSY-FRONT CONTROL BD COMPONENT PARTLIST
6
996510031364
ASSY-SWITCH BOARD
1
NO
20
996510031359
ASSY-FRONT CONTROL BOARD
1
LED1
996510020917
J2808AG
1
10
996510031298
ASSY-LOADER
1
REM301
996510020925
HM338-12 RECEIVER MOD H=12MM
1
OPU
996510031294
SANYO DV38
1
U301
996510009665
IC ET6202 SOP-2
1
ASSY-MAIN BD COMPONENT PARTLIST
NO
12NC NO.
D3
996510009668
D4
Description
U200
996500032494
12NC NO.
IC AS4558M
Description
1
Q'ty
MECHANICAL PARTLIST
Q'ty
No
12NC No.
BAT54C
1
11
996510027798
Description
BOTTOM PLATE
Q'ty
1
996510014439
SMD. SWITCHING DIODE LL4148
1
13
996510001175
POWER CORD
1
D5
996510020926
IC PESD5V0S1BA
1
15
996510031361
BACK PANEL
1
D50
996510014439
SMD. SWITCHING DIODE LL4148
1
17
996510006463
PAD
4
D6
996510020926
IC PESD5V0S1BA
1
2
996510031362
FRONT DOOR
1
D7
996510020926
IC PESD5V0S1BA
1
8
996510031367
TOP CABINET
1
D8
996510020926
IC PESD5V0S1BA
1
AVCABLE
996510001106
VIDEO CABLE 1500mm
1
L10
996500014082
COIL CHOKE 10UH +/-10%
1
Assy1
996510031363
ASSY-FRONT DOOR
1
L9
996500014082
COIL CHOKE 10UH +/-10%
1
CON503
996510011060
5PINCBLE TJC3-5Y/SCN-5P L=70MM
1
Q1
996510010922
ASM3402M/TR-LF SOT-23
1
HDMIL
996510031365
HDMI CABLE 1.5M
1
Q10
996510009671
PNP TRANSISTOR
1
PSOCKET
996510020885
POWER SOCKET transition
1
Q11
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
RC
996510031299
REMOTE CONTROL
1
Q12
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XP2
996510001168
24PIN HS
1
Q13
996510009670
TRANSISTOR SMT 3CG9012M
1
XP3
996510004063
CABLE PH-5Y/PH-5Y L=130MM
1
Q14
996510009670
TRANSISTOR SMT 3CG9012M
1
XP4
996510021448
6PIN HS
1
Q15
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XP601
996510020962
7PIN CABLE WITH SHIELD(XP7:
1
Q16
996510009671
PNP TRANSISTOR
1
XS301
996510001530
CABLE 10P HS
1
Q17
996510009671
PNP TRANSISTOR
1
Q2
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
SCREWS LIST:
Q21
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
No
Q22
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
7
—
S/T SCREW B 2.6 X 8 BF
6
Q23
996510009670
TRANSISTOR SMT 3CG9012M
1
12
—
S/T SCREW B3 X 6 BF
9
Q24
996510009670
TRANSISTOR SMT 3CG9012M
1
14
—
S/T SCREW B 3 X 7 BF
5
Q3
996510009671
PNP TRANSISTOR
1
Q7
996510009937
TRANSISTOR S8550LT1(PNP)
1
Q8
996510009937
TRANSISTOR S8550LT1(PNP)
1
Q9
996510022279
PNP TRANSISTOR SOT-23PBSS5320T
1
U2
996510009674
IC AM5888IC
1
U20
996510031368
IC 1389DX DECODE
1
U3
996510013349
HDMI USB ESD PYOTECTION IC
1
U4
996510009863
64M SDRAM TSOP54 M12L64164A-7T
1
U5
996510031293
16M FLASH 86MHZ MX25L1605DM2
1
U6
996510010924
Dual operational amplifier
1
Y2
996510009675
27MCL20PF
1
ASSY-POWER BD COMPONENT PARTLIST
NO
12NC NO.
Description
Q'ty
D501
996510011047
DIODE IN4007
1
D502
996510011047
DIODE IN4007
1
D503
996510011047
DIODE IN4007
1
D504
996510011047
DIODE IN4007
1
D506
996500014043
DIODE FR102 (FAST RECOVERY)
1
D507
996510011047
DIODE IN4007
1
D508
996500014043
DIODE FR102 (FAST RECOVERY)
1
D509
996500027866
DIODE SR360 3A/60V
1
L501
996510009942
COIL WIDTH
1
L502
996500032509
COIL SL0811-6R8K2R4
1
T501
996510031291
TRANSFORMER EE-19\\BCK-03EE19
1
U1
996510012685
IC TNY177PN
1
U502
996500027867
PHOTOCOUPLER PS2561L1-1-V(WF)
1
U503
996510010419
REG DE PRECISAO AJUSTAVEL
1
12NC No.
Description
Q'ty
9-1
REVISION LIST
Version 1.0
* Initial release for DVP3560K/55