Download Installation Manual

SA-02
Supervised Wireless Magnetic
Contact Sensor
Installation Instructions
1. General Description
The SA-02 Supervised Wireless Magnetic Contact Sensor is
a high-performance intrusion sensor, developed with the
highest level of technology to make it ideal for residential
and commercial applications.
1.1. Standard Features
•
•
Supervisor
Case and Back Tamper Detectors
•
•
•
•
•
•
ASIC and Microprocessor Technology
Up to 3-yr. battery life with SPS
Ultra-low current consumption
Readily replaceable 3.6V- 1/2 AA Lithium battery
SMD component technology
L.E.D. Test Function
2. Technical Specifications
2.1. Electrical Characteristics
Battery: Lithium Primary cell; 3.6-volt Lithium 900 mAh
Tadiran/Varta/Tekcell (SB-AA-02); 1/2 AA Size. (Low Battery
Signal when V-2.5V)
CAUTION! Dispose of properly. Do not recharge,
disassemble, heat, or incinerate.
Current: Standby - 23 uA; Transmit - 5 mA
Pulse Count: Fixed at single pulse
Detect Range: Sensitivity of up to 2 cm from magnet
Alarm Transmit: One second
2.2. Environmental Characteristics
Operating Temperature: -20°C to +50°C (-4°F to +122°F)
Operating Humidity: Up to 95% non-condensing (max.)
RF Frequency: Available in 433.92 MHz or 868.35 MHz, with
1m Watt
Installation: Indoor
Magnet: Standard magnet with plastic housing and wall
spacer, adjustable height
Tamper Switch 1: Detects removal of Magnetic Contact
Sensor Front Cover (protected by case tamper switch)
Tamper Switch 2: Detects removal of Magnetic Contact
Sensor from the wall or from corner mount (protected by
rear tamper switch)
Supervisor: The supervisory signal is routinely transmitted to
the panels every 20 minutes, advising the Tamper Status,
Battery Status, and Event Activation Status to the panel.
2.3. Physical Characteristics
Dimensions: 87mm(h)x35mm(w)x25mm(d)(3.5"x13/8"x1")
Weight: 37 grams (1.30 oz) without battery
3. Installation – Performance Criteria
The SA-02 Magnetic Contact Sensor detects the opening
and closing of doors and windows, and transmits this
information to the receiver panel.
•
AVOID placing the Magnetic Contact Sensor near
strong magnetic or electrical fields other than the
magnet with which it is intended to be used.
Otherwise, performance may be affected and false
alarms may occur.
•
AVOID mounting on or near large metal surfaces
and multiple concrete/steel walls, as this may
interfere or block the wireless signals. Make sure to
test the range from any location by using the RF Test
Procedure to ensure reception.
NOTE: Install the Magnetic Contact Sensor on windows or
doors that have firm hinges and firm locking action, to
prevent false alarms associated with wind or bumping.
4. Installation Instructions
4.1. Installing the Battery
Use only the 3.6 V Lithium battery (see battery
specifications in section 2.1).
1) Unscrew the case locking screw and remove the
front cover.
5)
a door opening and closing. The LED lights up to
indicate RF transmission.
Close the front cover and replace the locking
screw.
CAUTION: Do not touch the magnetic element
or the electronic components inside, as doing
so may cause damage.
2)
For a new unit, simply remove the plastic strip
contact breaker. For replacement, remove the
battery using a small screwdriver.
CAUTION: Notice the polarity. Replace with a
fresh battery.
3)
4)
1
Dispose of the old battery properly. Do not
recharge, disassemble, heat, or incinerate.
To test, depress both the back-tamper and the
case- tamper buttons, or use a magnet to simulate
Figure 1: Front of PCB
4.2. Selecting the Location
The location and mounting of the SA-02 affects both the
transmission range and the wear and tear of the
transmitter. Preferably the transmitter should be installed
as close as possible to the receiver, and mounted in a
0706-0960238+00
high location so that the transmission has less
interference.
1) Select a DOOR or WINDOW within a room or
hallway that best matches the criteria in section 3
(see Figure 2).
2) Make sure that the Magnetic Contact Sensor is
mounted on a sturdy, non-vibrating door or
window frame.
Note: Following this instruction reduces bumping
and vibration effects on the sensor, and extends
the life of the product.
3)
4)
Perform the RF Test from the proposed mounting
location to ensure that the sensor can be received.
Select the appropriate height for the magnet
assembly that suits the location of the sensor.
optionally activated for additional protection against the
theft or removal of the sensor from the mounting
location.
The back tamper can be activated to work in unison with
the case tamper by cutting the jumper R18 which is on
the top side of the PCB.
1) Remove the case locking screw and front cover.
You can now see the front of the PCB with the
antenna showing (see Figure 5).
2)
3)
Activate the back tamper switch by cutting the
jumper.
Replace the front cover and locking screw.
Figure 5: Activating the Back Tamper
4.6. Performing Radio Transmission Test
Figure 2: Selecting a Location
4.3. Selecting the Magnet Height
The SA-02 comes equipped with a standard magnet of
adjustable height, suitable for most applications.
When there is a mismatch in height between the door
and the frame, simply press on the sides of the
mechanism on the magnet, to adjust the height of the
magnet assembly to suit the location of the sensor.
Figure 3: Magnet
4.4. Wiring the External Sensor
When the internal magnetic sensor in the SA-02 is not
applicable, or an additional set of contacts is needed for
the SA-02, you can install a remote external magnetic
contact sensor to the SA-02 with a wire, using the
following procedure.
Note: The maximum distance between the external
contact and the SA-02 is about 8.5 meters or 25 feet.
1) Remove the case locking screw and front cover.
2) Connect the external magnet(s) in series to the
wired input terminal block of the magnetic contact
sensor.
3) Move the jumper cover to the two right-most pins
to activate the external magnetic contact input.
4) Replace the front cover and locking screw.
This test is used to check the range and reception of the
sensor to the control panel receiver. If reception is poor,
try to change the location of the Magnetic Contact
Sensor.
1) Ensure that all the settings of the Magnetic Contact
Sensor are adjusted as necessary for the location,
according to the steps in sections 4.1 to 4.5, and
that the Magnetic Contact Sensor case is closed,
with the locking screw firmly secured.
2) Hold the sensor as close as possible to the
mounting location, and transmit using the magnet.
3) During this mode, each time the LED flashes, the
sensor transmits to the panel. If the panel is armed,
an alarm is activated. If the panel is in test mode,
the signal strength can be measured.
4) It is recommended to try several locations until the
best reception is attained.
4.7. Mounting the Magnetic Contact Sensor
The SA-02 Magnetic Contact Sensor is designed to be
mounted onto a flat wooden or stucco surface.
1) Remove the PCB from the back case.
2) Remove the knockouts from the back case labeled
B, by using a sharp tool or using a nail.
3) Affix the two screws onto the wall, so that the Back
Tamper arm is pressed in.
4) Replace the PCB and tighten the PCB locking
screw.
5) Replace the top cover of the Magnetic Contact
Sensor.
Note: When mounting the SA-02 to the surface,
it is important to see that the surface is flush with
the back tamper device.
Figure 4: Wiring an External Sensor
4.5. Activating the Back Tamper
Each SA-02 Magnetic Contact Sensor is equipped with
both a Back and Case Tamper detector. The Case
tamper detector is always active; however, the wall
(back) tamper detector (normally inactive) can be
2
Figure 6: Mounting the SA-02
0706-0960238+00
4.8. Post-Installation Testing
After mounting the back of the sensor housing to the
window or door frame, it is important to check the
reliability of the RF transmission to the receiver or security
panel.
1) Perform a range test as indicated in section 4.6.
If the sensor is used with a receiver, check to see
that the receiver is receiving the sensor.
It is suggested that you arm the system, and test
that the SA-02 transmits to the desired control
panel.
Note: If the back tamper has been activated in previous
steps, check the security panel to ensure that there is no
tamper signal, and that the sensor is properly installed.
Caution: Dispose of the old battery properly. Do not
recharge, disassemble, heat, or incinerate.
1) Open the SA-02 sensor, and observe the correct
polarity labeled on the PCB and the holder.
2) Remove the old battery and dispose of it properly.
3) Insert the new battery (according to the
specifications in section 2.1).
Figure 7: Replacing the Battery
4.9. Replacing the Battery in the SA-02
Batteries in the SA-02 should be replaced following a Low
Battery indication on the receiver or security panel.
5. Limited Warranty
ROSSLARE ENTERPRISES LIMITED S (Rosslare) TWO YEAR LIMITED
WARRANTY is applicable worldwide. This warranty supersedes any other
warranty. Rosslare's TWO YEAR LIMITED WARRANTY is subject to the
following conditions:
Warranty
Warranty of Rosslare's products extends to the original purchaser (Customer) of
the Rosslare product and is not transferable.
Products Covered By This Warranty and Duration
ROSSLARE ENTERPRISES LTD. AND / OR SUBSIDIARIES (ROSSLARE)
warrants that the SA-02 Supervised Wireless Magnetic Contact Sensor is free
from defects in materials and assembly in the course of normal use and service.
The warranty period commences with the date of shipment to the original
purchaser and extends for a period of 2 years (24 months).
Warranty Remedy Coverage
In the event of a breach of warranty, ROSSLARE will credit Customer with the
price of the Product paid by Customer, provided that the warranty claim is
delivered to ROSSLARE by the Customer during the warranty period in
accordance with the terms of this warranty. Unless otherwise requested by
ROSSLARE ENTERPRISES LTD. AND / OR SUBSIDIARIES representative,
return of the failed product(s) is not immediately required.
If ROSSLARE has not contacted the Customer within a sixty (60) day holding
period following the delivery of the warranty claim, Customer will not be required
to return the failed product(s). All returned Product(s), as may be requested at
ROSSLARE ENTERPRISES LTD. AND / OR SUBSIDIARY’S sole discretion,
shall become the property of ROSSLARE ENTERPRISES LTD. AND / OR
SUBSIDIARIES.
To exercise the warranty, the user must contact Rosslare Enterprises Ltd. to
obtain an RMA number after which, the product must be returned to the
Manufacturer freight prepaid and insured.
In the event ROSSLARE chooses to perform a product evaluation within the
sixty (60) day holding period and no defect is found, a minimum US$ 50.00 or
equivalent charge will be applied to each Product for labor required in the
evaluation.
Rosslare will repair or replace, at its discretion, any product that under normal
conditions of use and service proves to be defective in material or
workmanship. No charge will be applied for labor or parts with respect to
defects covered by this warranty, provided that the work is done by Rosslare or
a Rosslare authorized service center.
Product is incorporated. This warranty shall not extend to any ancillary
equipment not furnished by ROSSLARE, which is attached to or used in
conjunction with a Product, nor to any Product that is used with any ancillary
equipment, which is not furnished by ROSSLARE.
This warranty does not cover expenses incurred in the transportation, freight
cost to the repair center, removal or reinstallation of the product, whether or not
proven defective.
Specifically excluded from this warranty are any failures resulting from
Customer's improper testing, operation, installation, or damage resulting from
use of the Product in other than its normal and customary manner, or any
maintenance, modification, alteration, or adjustment or any type of abuse,
neglect, accident, misuse, improper operation, normal wear, defects or damage
due to lightning or other electrical discharge. This warranty does not cover
repair or replacement where normal use has exhausted the life of a part or
instrument, or any modification, abuse of, or tampering with the Product, if
Product disassembled or repaired in such a manner as to adversely affect
performance or prevent adequate inspection and testing to verify any warranty
claim.
ROSSLARE does not warrant the installation, maintenance, or service of the
Product. Service life of the product is dependent upon the care it receives and
the conditions under which it has to operate.
In no event shall Rosslare be liable for incidental or consequential damages.
Limited Warranty Terms
THIS WARRANTY SETS FORTH THE FULL EXTENT OF ROSSLARE ENTERPRISES LTD. AND ITS
SUBSIDIARIES’ WARRANTY.
THE TERMS OF THIS WARRANTY MAY NOT BE VARIED BY ANY PERSON, WHETHER OR NOT
PURPORTING TO REPRESENT OR ACT ON BEHALF OF ROSSLARE.
THIS LIMITED WARRANTY IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES. ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
SPECIFICALLY EXCLUDED.
IN NO EVENT SHALL ROSSLARE BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE
PRICE OF THE PRODUCT, OR FOR ANY OTHER INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF USE, LOSS OF TIME, COMMERCIAL
LOSS, INCONVENIENCE, AND LOSS OF PROFITS, ARISING OUT OF THE INSTALLATION, USE,
OR INABILITY TO USE SUCH PRODUCT, TO THE FULLEST EXTENT THAT ANY SUCH LOSS OR
DAMAGE MAY BE DISCLAIMED BY LAW .
THIS WARRANTY SHALL BECOME NULL AND VOID IN THE EVENT OF A VIOLATION OF THE
PROVISIONS OF THIS LIMITED WARRANTY.
Exclusions and Limitations
ROSSLARE shall not be responsible or liable for any damage or loss resulting
from the operation or performance of any Product or any systems in which a
6. Technical Support
Asia Pacific, Middle East, Africa
Europe
Headquarters:
Global Technical Support & Training Center:
905-912 Wing Fat Industrial Bldg, 12 Wang Tai Road, Kowloon Bay Hong
Kong
Tel: +852 2795-5630 Fax: +852 2795-1508 E-mail:
[email protected]
HaMelecha 22 Rosh HaAyin, Israel 48091
Tel: +972 3 938-6838 Fax: +972 3 938-6830 E-mail:
[email protected]
United States and Canada
1600 Hart Court, Suite 103 Southlake, TX, USA 76092
Toll Free: +1-866-632-1101 Local: +1-817-305-0006 Fax: +1-817-305-0069
E-mail: [email protected]
3
South America
Pringles 868, 1640 Martinez Buenos Aires Argentina Tel: +54 11 47980095 Fax: +54 11 4798-2228
Web Site: www.rosslaresecurity.com
0706-0960238+00