Download MS International SMOT-SGLS-DM8MM Use and Care Manual
Transcript
M. S.. Interrnatio onal, IInc. Installation of o Mosa aic She eets Toolls and Equ uipment: Diam mond disc fo or cutting mosaics Finish Nails 1/1 16 – 3/16 V No otch Trowel S Sponge Grout G Float B Bucket Level Non n-Sanded Grout strate Prep paration: Subs n to be e clean, com mpact, perfe ectly flat an nd free of diirt and The substrate needs ks. Nylon or o wire brus sh can be used u in clea aning the re esidues on tthe surface e. crack If the e brush can nnot remove e the entire residue usse bead bla asting or san nd blasting. Fix all a the uneve en area of the t surface e; leveling ccompound m might be ne eeded to make e the surfac ce perfectly y flat. Smalll cracks ca an be fixed u using crackk supp pression me embrane orr patch. Co onsult an en ngineer for an assessm ment of large e cracks because this might caus se a problem m in the future. NOTE: Make sure eno ough time is i given to llet the subsstrate settle e (as per manu ufacturer’s recommen ndation). Do o not installll the mosaiic tiles direcctly over plyw wood or dryw wall. Page | 1 alling Mosa aic Sheets: Insta Before starting the installation inspect all mosaicc sheets an nd make sure that erial is in go ood conditio on and has no defectss. Identify th he starting point using g mate guide elines that will w help ins stalling the mosaics sttraight and symmetrica al. The size of the trowel depe ends on the e thicknesss of the mossaic tiles, th hinner the erial the smaller the tro owel. mate The mosaic, unless otherw wise specifie ed by the ccustomer, iss usually laiid on white masttic or thinse et to avoid altering a its color. c NOTE: Wh hite thinset is i usually re ecommend ded to use ffor the glasss and otherr cts to avoid discoloratio on of the ba ackground.. light or transparrent produc Once O the sta arting grid has h been marked, m usin ng the flat side of the v-notched v trrowel, apply y a layer off thinset and d use the notc ched side to o go over th he thinset to o make s to apply only enou ugh adhesive uniform depth. Make sure to o area that you can tile e within 15 minutes be ecause it drries quickly. Once O the ad dhesive is spread s overr the surface e, start layiing down the mo osaic sheetts. Using U a grou ut float, pre ess the mos saic sheet a against the surface to gu uarantee pe erfect adhe esion. Usin ng the same e ool, correct any alignm ment errors by lightly ta apping the to sides of the sheet. If th he sheet sta arts to slide e down, place fe ew finish na ails on the first f grout lin ne on the to op to hold it in place and th hen move to o the next tile. Afterr one sectio on is done, use damp sponge s to cclean up an ny residue o of thinset that may m have squeezed s up u between the tiles. NOTE: Thiinset usuallly requires 24 2 hours fo or curing. F For more tim me, check m er’s recomm mendation. the manufacture Page | 2 uting and Finishing: F Grou Before applying g grout, mak ke sure tha at the adhessive is set a and firm and d the tiles c Non-sanded gro out is recom mmended fo or mosaic ssheets due to small are clean. groutt joints. NOTE: It is s not recom mmended to o use sande ed grout on polished g glass mosa aics as this s will scratch h the materrial. Unlesss specified by the man nufacturer, epox xy grout is also a not rec commended d for the gla ass mosaicc tiles. Using U grout float apply the grout on o the tiles. Use verticcal and horizonttal strokes to spread the grout evvenly. Applly a litttle pressurre to make sure that all the joints are well filled. While W the grrout is still frresh, stroke e diagonallyy with the lo ong edge off the grout float f to rem move excesss grout. W Wipe with w a wet sp ponge to clean. due left ove e the grout is set and dry, d if there e is still resid er, use nylo on brush to Once clean n. Apply grrout sealer according to t manufaccturer’s instrructions. TIP: Cuttiing mosaics s using a wet w saw – To o make a g good, straig ght cuts on a s put a tile t or a piece of hard plastic dow wn on the cu utting tray. This helps wet saw, supp port the mos saic and ke eeps it from falling thro ough the wide opening g on the blade e channel tray. Page | 3