Download HSM PS825s
Transcript
IMPORTA ANT SAFETY NOT TES Turn off and unplu ug the shredder beffore moving, emptying the waste bin, or if the shredder will not be used d for a long period of o time. Keep children and pets away from sh hredder. Do not place fingers, hands or any fo oreign objects in the e feed slot. Serious injury may y result. Shred only one cre edit card at a time. Keep ties, jewelry, hair and loose clotthing away from the e feed slot. Serious injury may y result. Do not use canned d air on shredder. Never use aerosol,, petroleum based or other flam mmable products on or near shredde er. Do not exceed the e recommended pap per capacity of 25 sheets. s One folded sheet of paper equals 2 sheets s. An occasional paper p clip or owed. metal staple is allo Shred only one CD D, DVD at a time. D Do not shred envelo opes or labels with a sticky substance e like glue. Do not sshred wet paper, ca arbon paper or viny yl bags. The shred will stick in the ccutters and may cause paper jams or lower shredding pe erformance. E Empty the wasteba asket regularly to prrevent paper jams. D Do not operate if th he power cord appe ears damaged. Do not alter this unit or o ccord in any way. D Do not place this sh hredder near waterr or any heat source e. Keep 6 inches a away from wall. D Do not use any oil or o lubricants not cle early specified for shredder s use in or a around this unit. So ome agents may co ombust causing serious injury. If an extension cord d is used, make surre that the total ampere ratings of the p products plugged in nto the extension co ord do not exceed the t extension cord a ampere rating, and that the total of all products plugged into i the wall outlet d does not exceed 15 5 amps. T This shredder shou uld be used only witth an operator in attendance. Keep sshredder in the ON/OFF position and unplug from the AC C outlet when not in n u use for an extended d period of time. A Avoid exposing the shredder to direct sunlight. TECHN NICAL DATA Part Number: y Level: Security Shred Size: S Throat: Maximu um Capacity: Shred Bin B Capacity: Voltage e: Noise le evel: Weight: Duty cycle: HSM1052 2 1/4” (5.8mm)(strip p cut) 9” (228.6 mm) 25 sheets 7.1 gallons (26,8 liters) 115 V/60 Hz 63 dB 26.4 lbs. (12 kg) 5 minutes on/30 m minutes off LLATION: INSTAL -Unpack k and set the machhine upright on leve el surface. -Make sure s the waste bin iis properly inserted d into the shredder cabinet. -Plug in the machine. Seee “TECHNICAL DAT TA” for necessary p precautions. -The ou utlet should be instaalled near the equip pment and be easilyy accessible. The ma ain connection at thee machine must be e freely accessible. MAINTE ENANCE INSTRUC CTIONS To ensu ure proper operatioon and function, perriodic oiling of the ccutting system is required d. Failure to oil youur cutting system co ould result in reducced sheet capacity perform mance, excess noisee, paper jams and possible machine ffailure. Oil yourr cutters every 5th-66th time you empty tthe basket if excesss squeaking and rubbing noise is coming froom the machine or if the shredder’s sh heet capacity has diminish hed. -Squeez ze the lubricant acrross the full width o of the cutters. -Clean the t shredder housinng using a soft clotth dampened with a mild solution of deterge ent (such as dish waashing liquid) and w warm water. DO NO OT use chemical cleaners s or solvents. CLEAN NING PHOTO EYE SENSORS 1. 2. 3. 4. 5. ety Unplug your macchine – for your safe nue machine (If no flap installed, disregard this line and contin Lift CD Flap on m on) Note: In the ccenter of the paperr slot, you should se ee (2) transparent squares - one on either side of the sslot. nd Use compressed air or take a dry tisssue or paper towe el and wipe back an forth a few times just to dust that are ea off Replace flap if neecessary Plug machine bacck in OPERATING INSTRUCTION NS 4. After shredding, ppress the stand-by button Ⓑ to turn offf the shredder and turn off the powerr switch in back of sshredder Ⓐ. 5. Empty the waste bin regularly to pre event jams and dam mage to cutting mechanism. JAM-ALER RT gy. The jam-alert iccon Ⓕ will blink This uniit is equipped with jjam-alert technolog indicatin ng that the maximuum sheet capacity h has been exceeded d. Reduce the num mber of sheetts and place the paaper back into the p paper feed. SHREDDER CONTROLS Buttons Switch Main Powe er Switch Ⓐ to ON position. Press Power Butto on Ⓑ to turn on. Press Power Butto on Ⓑ to turn the po ower off. Press and hold FW WD to manually ope erate shredder in fo orward Ⓔ. Press and hold RE EV to manually operate shredder in rev verse Ⓗ. OPERATION 1. T Turn on the main po ower switch in back k of shredder Ⓐ. Press P the stand-by b button Ⓑ. The follo owing function butto ons will illuminate: stand-by s button Ⓑ,, tthe FWD Ⓔ and RE EV Ⓗ. 2. Insert paper into pa aper feed slot Ⓒ. Do D not fee more tha an 25 sheets at one e ttime. The shredderr will stop after pap per has passed thro ough. 3. T To shred a CD, DVD or credit card ins sert through designated slot Ⓖ. STAND DBY MODE The shrredder is equipped with an energy savving standby mode which will activate after 30 minutes of being iddle. To resume, prress the stand-by b button Ⓑ. TROUBLESHOOTING STANDARD PRODUCT WARRANTY SHREDDER WILL NOT OPERATE Quality is part of the company philosophy and all products are manufactured to the highest quality standards. All technical data and measurements are approximate values and based upon single shift operations. All products are subject to different limits and specifications due to operation length, paper size, grain, weight, misuse/abuse and power configurations. 1. Make sure shredder is plugged into power source and the main power switch Ⓐ is switched on. 2. Make sure the waste bin is fully inserted into the shredder housing. PAPER JAM 1. 2. 3. Press and hold REV Ⓗ button to clear the jam. Press power button to continue shredding. CAUTION: Sharp cutter blades. Do not reach underneath the shredder head to remove jammed paper. Serious injury can result. If the paper jam cannot be cleared by pressing the REV button: a. Tear or cut the remaining paper just above the shredder throat. b. Press power button Ⓑ to switch off the machine. c. Press power button Ⓑ again to switch on the machine in order to d. clean the jammed paper inside the throat. Repeat steps (b) and (c) until all paper is cleared from inside the throat. SHREDDER STOPS WHILE SHREDDING Prior to operation read the Manufacturers Operating Instructions included with this product. This will help ensure all precautions are taken to avoid cancellation of the manufacturer’s warranty. The manufacturer warrants that any new products sold will be free from defects in material and workmanship when used under specified and normal operating conditions. This warranty is void if repairs are necessitated by accident, misuse, abuse, water damage or fire. The capabilities of all products are in each specification flier. Exceeding model specifications causing product failure is not covered by this warranty. Modifications, alterations and repairs must be performed by an authorized technician. Lubrication for cross cut shredders is required every fifteen to thirty minutes of operation, to maintain top working condition and this warranty. Compact Shredders & Shredstar Models 1. Switch off the main power switch Ⓐ and unplug the shredder from the power 2. Plug the shredder into power source. Switch on the main power switch Ⓐ in Failure caused by defect is limited to two (2) years from date of invoice. A maximum of one replacement unit is authorized during the warranty period. Strip and cross cut cutting rollers are warranted to be free of manufacturer defects for the life of the shredder from date of invoice. back of shredder and press the stand-by button Ⓑ. Notes: source. 3. For further troubleshooting, please contact product support 800-613-2110. Freight or transportation damage is not classified as a warranty repair in any case. Proof of purchase invoice is required from the end-user warranty validation or warranty registration date. All parts under warranty will be shipped and invoiced using standard costs and will be credited for the full amount only when the defective part is returned.