Download Woodstock D3277 User's Manual
Transcript
Instruction Sheet Model D3277 Gravity Feed Spray Gun INTRODUCTION This gravity feed spray gun with a 1.4mm nozzle includes an in-line regulator for precise control and a chrome finish for easy clean-up. Nozzle Control Fluid Control SETUP Attach the regulator to the base of the spray gun, then attach the airline to the regulator with a 1⁄4 NPT fitting. Use the adjustment knob on the regulator to set the air pressure to 30 PSI. ADJUSTMENTS See Figure 1 to identify the location of the spray gun controls and adjust in the following order: 1. 2. 3. 4. Fluid Control—Adjusts the trigger travel, which affects the volume of paint released. Air Flow Control—Adjusts the volume of air that mixes with the paint, and thus, increases or decreases the paint atomization. Pattern Control—Variably adjusts the spray pattern from round to a wide fan. Nozzle Control—Adjusts the spray pattern from vertical to horizontal. OPERATIONS Hold the sprayer 6"–8" from the workpiece, and keep the spray gun perpendicular to the workpiece during strokes. DO NOT pivot your wrist when spraying! MAINTENANCE 1. Clean the spray gun by flushing it with thinner; however, DO NOT immerse the gun in the thinner! 2. Regularly clean the filter between the container and spray gun. 3. To avoid internal damage, only use the included brush when cleaning inside the spray gun orifices. Air Flow Control Pattern Control Figure 1. Model D3277. EXPLOSION HAZARD! Do not spray flammable fluids near an open flame or ignition source. EYE INJURY AND RESPIRATORY HAZARD! Always use safety glasses and respirator rated for paint and solvent vapors while using sprayer. CUSTOMER SERVICE For questions contact Woodstock International Technical Support at (360) 734-3482, or send email to: [email protected]. COPYRIGHT © BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS DOCUMENT MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. SEPTEMBER 2003, PRINTED IN CHINA. D3277 Parts Diagram 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 4 5 6 7 8 9 10 11 12 13 34 33 32 31 39 3 2 1 38 37 36 35 40 41 42 43 44 REF 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 PART # XD3277001 XD3277002 XD3277003 XD3277004 XD3277005 XD3277006 XD3277007 XD3277008 XD3277009 XD3277010 XD3277011 XD3277012 XD3277013 XD3277014 XD3277015 XD3277016 XPEC02M XPEC02M XD3277019 XD3277020 XD3277021 XD3277022 DESCRIPTION REF DOMED SEAL WASHER SWITCH KNOB SWITCH POLE LOCKED SPRING NOZZLE NUT SEAL WASHER 30MM ATOMIZATION FLUID NOZZLE FLUID NOZZLE PLUG SEAL WASHER 10MM DIRECTION SCREW DOMED SEAL WASHER SPRING TRIGGER PIN I TRIGGER PIN II TRIGGER E-CLIP 4MM E-CLIP 4MM BREATHER PLUG CONTAINER COVER CONTAINER FILTER 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 PART # XD3277023 XPEC09M XD3277025 XD3277026 XD3277027 XD3277028 XD3277029 XPFH31M XD3277031 XD3277032 XD3277033 XD3277034 XD3277035 XD3277036 XD3277037 XD3277038 XD3277039 XD3277040 XD3277041 XD3277042 XD3277043 XD3277044 DESCRIPTION FLUID INLET JOINT E-CLIP 6MM O-RING PATTERN ADJ. COPPER WASHER 8MM PATTERN ADJ. KNOB PATTERN ADJ. SCREW FLAT HD SCR M6-1 X 8 FLUID ADJ. KNOB JOINT CAP FLUID NEEDLE SPRING FLUID ADJ. NEEDLE MODULATOR SWITCH SPRING SWITCH BLOCK O-RING SPECIAL SET SCREW M4 X 14 GUN BODY AIR INLET PLUG MULTI-TOOL WRENCH HEX SOCKET TOOL BRUSH