Download Weider WEEVSY2026 User's Manual

Model No. WEEVSY2026.0
Serial No.
Write the serial number in the
space above for future reference.
USER'S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, please call:
08457 089 009
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: [email protected]
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.iconeurope.com
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
The decal shown here has been placed on
the weight system. If the decal is missing or
illegible, please call the telephone number on
the front cover of this manual and order a
free replacement decal. Apply the decal in the
location shown.
VERTICAL WARNING
PN 218558 – Black Text/Clear Background
PN 218559 – White Text/Clear Background
WEIDER is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions before using the weight system.
1. Read all instructions in this manual and in
the accompanying literature and all warnings
on the weight system before using the
weight system. Use the weight system only
as described in this manual.
6. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
2. It is the responsibility of the owner to ensure
that all users of the weight system are adequately informed of all precautions.
8. Always wear athletic shoes for foot protection when using the weight system.
7. Keep children under the age of 12 and pets
away from the weight system at all times.
9. Keep hands and feet away from moving parts.
3. The weight system is intended for home use
only. Do not use the weight system in a commercial, rental, or institutional setting.
10. The weight system is designed to support a
maximum user weight of 135 kg (300 lbs).
4. Keep the weight system indoors, away from
moisture and dust. Place the weight system
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
system to mount, dismount, and use the
weight system.
11. Always stand on the foot plate when performing an exercise that could cause the
weight system to tip.
5. This weight system has an open weight
stack; the weight stack must not be accessible from any point outside of the user’s field
of view. To prevent access to the weight
stack, place the weight system in a corner or
bay of a room, as shown in the drawing
below. There must be no more than 1 meter
(3 ft. 4 in.) of clearance between the weight
system and the adjacent walls.
13. Always disconnect the lat bar from the
weight system when performing an exercise
that does not use the lat bar.
12. Never release the arms, leg lever, or lat bar
while weights are raised; the weights will fall
with great force.
14. The weight system is designed to be used
only with the included weight. Do not use the
weight system with dumbbells or any other
type of weight to increase the resistance.
15. Make sure that the cables remain on the pulleys at all times. If the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.
Wall
16. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® PRO
2000 weight system. The weight system offers a selection of weight stations designed to develop every
major muscle group of the body. Whether your goal is
to tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
weight system will help you to achieve the results you
want.
reading this manual, see the front cover of this manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number is WEEVSY2026.0. The serial
number can be found on a decal attached to the
weight system (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight system. If you have questions after
Lat Bar
High Pulley Station
Press Frame Lock
Butterfly Arm/Press Arm
Backrest
Weight Stack
Seat
Leg Lever
ASSEMBLED DIMENSIONS:
Height: 79 in. (200 cm)
Width: 37 in. (93 cm)
Depth: 52 in. (132 cm)
Foot Plate
4
PART IDENTIFICATION CHART—Model No. WEEVSY2026.0
M4 x 12mm Selftapping Screw (56)
M6 x 63mm Screw (67)
M8 x 63mm Bolt (66)
M6 x 58mm Screw (65)
M6 x 16mm
Screw (40)
M10 x 65mm Carriage Bolt (59)
M10 x 52mm Bolt (52)
M4 x 19mm Selftapping Screw (76)
M8 x 70mm Carriage Bolt (86)
M10 x 46mm Bolt (53)
M6 Washer (73)
M10 x 57mm Bolt Set (81)
M8 x 45mm Bolt (60)
M6 x 43mm Bolt (61)
M10 x 65mm Bolt (55)
M8 Washer (71)
M8 x 63mm Carriage Bolt (58)
M8 x 68mm Bolt (63)
M10 Washer (70)
M10 x 70mm Bolt (57)
M6 Nylon Locknut (72)
M10 x 78mm Bolt (54)
25mm Washer (29)
M8 Nylon Locknut (69)
M10 x 100mm Bolt (46)
M4 Washer (77)
M10 x 125mm Bolt (64)
M10 Nylon Locknut (68)
M10 x 155mm Bolt (62)
5
ASSEMBLY
• As you assemble the weight system, make sure
all parts are oriented as shown in the drawings.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight system can be assembled successfully by anyone. However, it is important to
realize that the versatile weight system has
many parts and that the assembly process will
take time. Most people find that by setting aside
plenty of time, assembly will go smoothly.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The following tools (not included) are required
for assembly:
• two adjustable spanners
• one rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• one standard screwdriver
• Assembly requires two people.
• one Phillips screwdriver
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end spanners, or a set of ratchet spanners.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1
FRAME ASSEMBLY
1.
68
Before beginning assembly, be sure that
you have read and understand the information in the box above.
These
holes are
smaller
than on
the opposite side.
1
Orient the Stabilizer (2) as shown with the
indents around the holes facing downward.
Attach the Base (1) to the Stabilizer with two
M10 x 65mm Carriage Bolts (59) and two M10
Nylon Locknuts (68). Do not tighten the Nylon
Locknuts yet.
Indent
58
59
2
59 Indent
Insert two M8 x 63mm Carriage Bolts (58) into
the bottom of the Base (1). Note: It may be
helpful to place tape over the bolt heads to
hold them in place.
6
2. Attach the Upright (3) to the Base (1) with the two
M8 x 63mm Carriage Bolts (58) and two M8
Nylon Locknuts (69). Do not tighten the Nylon
Locknuts yet.
2
66
Attach the Press Frame Lock (39) to the Upright
(3) with an M8 x 63mm Bolt (66), two M8
Washers (71), and an M8 Nylon Locknut (69). Do
not overtighten the Nylon Locknut; the Press
Frame Lock must pivot easily.
39
71
71
69
3
69
69
1
58
3. Set two Weight Bumpers (17) over the indicated
holes in the Stabilizer (2). Insert two Weight
Guides (10) into the same holes. Make sure that
the indicated holes are closer to the bottom of
the Weight Guides. Secure the Weight Guides in
place with two M10 x 70mm Bolts (57), two M10
Washers (70), two Small Spacers (37), and two
M10 Nylon Locknuts (68).
3
Tighten the M10 Nylon Locknuts (68) used in
steps 1 and 3.
10
Holes
70
17
68
37
17
68
7
57
2
4. Slide ten Weights (15) onto the Weight Guides
(10), with the slot for the Weight Pin (not shown)
on the bottom and on the side facing away from
the Upright (3).
4
10
Lubricate
15
Insert the Weight Tube (12) into the Weights (15).
Lubricate the indicated holes in a Weight (15)
with grease. Slide the Weight onto the Weight
Guides (10).
3
12
15
5. Attach the Top Frame (4) to the Upright (3) with
two M8 x 68mm Bolts (63) and two M8 Nylon
Locknuts (69). Do not tighten the Nylon
Locknuts yet.
5
4
Attach the Top Frame (4) between the Weight
Guides (10) with an M10 x 155mm Bolt (62), two
M10 Washers (70), and an M10 Nylon Locknut
(68).
10
62
70
70
63
Tighten the Nylon Locknuts (68, 69) used in
steps 2 and 5.
68
3
6. Attach the Seat Frame (8) to the Upright (3) with
an M8 x 70mm Carriage Bolt (86) and an M8
Knob (82).
69
6
3
86
Attach the Bumper (75) to the Seat Frame (8)
with an M4 x 19mm Self-tapping Screw (76) and
an M4 Washer (77).
8
82
76
77 75
8
7
ARM ASSEMBLY
Grease
8
81
7. Grease the M10 x 57mm Bolt Set (81) and attach
the Leg Lever to the Seat Frame (8) with the Bolt
Set. Make sure that the barrel of the Bolt Set
is inserted through both sides of the bracket
on the Seat Frame. Do not overtighten the
Bolt Set; the Leg Lever must pivot easily.
81
9
8. Apply grease to an M10 x 125mm Bolt (64).
Orient the Press Frame (5) with the bracket on
the side shown. Attach the Press Frame to the
Top Frame (4) with the Bolt, two M10 Washers
(70), and an M10 Nylon Locknut (68). Do not
overtighten the Nylon Locknut; the Press
Frame must pivot easily.
8
64
4
70
Grease
70
68
5
Bracket
9. Attach an Arm Pad (20) to the Left Arm (7) with
two M6 x 58mm Screws (65) and two M6
Washers (73).
9
Repeat this step with the Right Arm (6).
6
7
73
65
73
9
20
10. Insert the post on the Left Arm (7) through the
hole in the Press Frame (5). Make sure the
Arm is behind the indicated bracket on the
Press Frame.
10
27
6
29
Slide a 25mm Washer (29) over the post on the
Left Arm (7). Attach an M6 x 43mm Bolt (61) to
the post with an M6 Nylon Locknut (72). Make
sure the Nylon Locknut and the head of the
Bolt are over the edge of the Washer, as
shown in the inset drawing.
5
Bracket
72
7
61
Press a 25mm Round Outer Cap (27) onto the
post on the Left Arm (7).
Post
61
Repeat this step with the Right Arm (6).
72
29
CABLE ASSEMBLY
11
50
4
55
34
37
11. See the CABLE DIAGRAM on page 19 for
proper cable routing.
70
37
Locate the High Cable (50). Route the threaded shaft end of the Cable up through the Top
Frame (4) and over a 90mm Pulley (34). Attach
the Pulley inside the Top Frame with an M10 x
65mm Bolt (55), two M10 Washers (70), two
Small Spacers (37), and an M10 Nylon Locknut
(68).
70
68
12. Route the High Cable (50) over a 90mm Pulley
(34) and down through the Top Frame (4).
Attach the Pulley and a Cable Trap (36) to the
bracket on the Top Frame with an M10 x 52mm
Bolt (52) and an M10 Nylon Locknut (68). Make
sure the Cable Trap is oriented to hold the
Cable in the groove of the Pulley.
12
13. Route the High Cable (50) under a 90mm
Pulley (34). Attach the Pulley, a Cable Trap
(36), and two Finger Guards (35) to the second
set of holes from the top of the two Pulley
Plates (44) with an M10 x 52mm Bolt (52) and
an M10 Nylon Locknut (68). Make sure that
the Cable Trap is oriented to hold the Cable
in the groove of the Pulley.
13
34
36
68
50
52
35
52
50
35
44
36 34
44
10
68
4
14. Wrap the High Cable (50) over a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Top Frame (4) with an M10 x 46mm
Bolt (53) and an M10 Nylon Locknut (68).
53
14
35
4
35
Repeat this step with another 90mm Pulley
(34), two Finger Guards (35), an M10 x 46mm
Bolt (53), and an M10 Nylon Locknut (68).
35
34
15. Attach the end of the High Cable (50) to the
Small “U”-bracket (11) with an M8 Washer (71)
and an M8 Nylon Locknut (69). Note: Do not
completely tighten the Nylon Locknut; it
should be threaded onto the Cable so that
two threads show past the Nylon Locknut,
as shown in the inset drawing.
15
50
60
11
69
71
69
12
Attach the Small “U”-bracket (11) to the Weight
Tube (12) with an M8 x 45mm Bolt (60) and an
M8 Nylon Locknut (69). Do not overtighten
the Nylon Locknut; the Weight Tube must
pivot easily in the Small “U”-bracket.
16. Locate the Press Cable (49). Slide the Cable
onto the hook on the Left Arm (7).
68
50
50
11
69
16
Hook
49
7
17. Apply grease to an M10 x 78mm Bolt (54).
Attach the Pulley Arm (38) to the Upright (3)
with the Bolt and an M10 Nylon Locknut (68).
Do not overtighten the Nylon Locknut; the
Pulley Arm must pivot easily.
17
54 35
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an
M10 Washer (70), and two Finger Guards (35)
to the indicated side of the Pulley Arm (38) with
an M10 x 52mm Bolt (52) and an M10 Nylon
Locknut (68). Make sure that the Cable Trap
is oriented to hold the Cable in the groove
of the Pulley.
38
36
52
68
34 35
70
3
11
49
18. Wrap the Press Cable (49) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Double “U”-bracket (42) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68).
18
49
34
35
35
53
68
19. Apply grease to an M10 x 78mm Bolt (54).
Attach a Pulley Arm (38) to the Upright (3) with
the Bolt and an M10 Nylon Locknut (68). Do
not overtighten the Nylon Locknut; the
Pulley Arm must pivot easily.
42
19
Grease
52
54
38
35
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an
M10 Washer (70), and two Finger Guards (35)
to the indicated side of a Pulley Arm (38) with
an M10 x 52mm Bolt (52) and an M10 Nylon
Locknut (68). Make sure that the Cable Trap
is oriented to hold the Cable in the groove
of the Pulley.
68
36
34
49
70
35
3
68
20. Slide the end of the Press Cable (49) onto the
hook on the Right Arm (6).
20
49
6
21. Locate the Short Cable (47). Attach the eyelet
on the Cable to the Base (1) with an M10 x
70mm Bolt (57), an M10 Washer (70), and an
M10 Nylon Locknut (68). Do not overtighten
the Nylon Locknut.
21
68
1
12
70
47
57
22. Wrap the Short Cable (47) over a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Double “U”-bracket (42) with an M10
x 46mm Bolt (53) and an M10 Nylon Locknut
(68).
22
53
35
35
42
68
47
34
23. Attach the end of the Short Cable (47) to the
“U”-bracket (43) with an M8 Washer (71) and
an M8 Nylon Locknut (69). Note: Do not completely tighten the Nylon Locknut; it should
be threaded onto the Cable so that two
threads show past the Nylon Locknut, as
shown in the inset drawing.
23
47
47
43
43
71
69
24. Locate the Low Cable (48). Attach the Cable
inside the Base (1) with an M10 x 65mm Bolt
(55), two M10 Washers (70), two Large
Spacers (51), and an M10 Nylon Locknut (68).
69
24
48
55
70
51
51
70
1
25. Route the Low Cable (48) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), and
two Finger Guards (35) to the second set of
holes from the bottom of the two Pulley Plates
(44) with an M10 x 52mm Bolt (52) and an M10
Nylon Locknut (68). Make sure that the Cable
Trap is oriented to hold the Cable in the
groove of the Pulley.
25
52
44
35
35
36
34 68
48
13
68
26. Wrap the Low Cable (48) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the bracket on the Base (1) with an M10
x 46mm Bolt (53) and an M10 Nylon Locknut
(68).
26
34
48
53
35
35
1
68
27. Route the Low Cable (48) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), and
two Finger Guards (35) to the lower set of holes
in the “U”-bracket (43) with an M10 x 52mm
Bolt (52) and an M10 Nylon Locknut (68). Make
sure that the Cable Trap is oriented to hold
the Cable in the groove of the Pulley.
27
52 43
35 68
35
36
34
48
28. Route the Low Cable (48) under a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), and
two Guards (14) to the Upright (3) with an M10
x 100mm Bolt (46), two M10 Washers (70), and
an M10 Nylon Locknut (68). Make sure that
the Cable Trap is oriented to hold the Cable
in the groove of the Pulley.
28
3
68
70
34
14
14
70
48
36
46
29. Attach the Cable Hook (30) to the Leg Lever (9)
with an M10 Washer (70) and an M10 Nylon
Locknut (68).
29
Attach the Low Cable (48) to the Chain (83)
and to the Cable Hook (30) with two Cable
Clips (33).
9
83
48
30
70
33
68
14
SEAT ASSEMBLY
30
30. Attach the Backrest (18) to the Upright (3) with
two M6 x 63mm Screws (67) and two M6
Washers (73).
73
67
3
73
18
67
Wide End
31. Attach the Seat (19), oriented as shown, to the
Seat Frame (8) with four M6 x 16mm Screws
(40).
31
19
Wide
End
8
40
40
32. Slide a Pad Tube (45) through the hole in the
Leg Lever (9). Slide two Foam Pads (21) onto
the ends of the Pad Tube. Then, press two Pad
Caps (22) onto the Pad Tube.
32
45
22
Repeat this step with the other Pad Tube
(45) and the Seat Frame (8).
8
21
9
21
45
15
22
33. Attach the Right and Left Shroud Frames (84, 85)
to the Top Frame (4) with an M8 x 68mm Bolt
(63) and an M8 Nylon Locknut (69). Do not tighten the Nylon Locknut yet.
33
84
63
4
85
69
18
34. Attach the Left Shroud (87) to the Left Shroud
Frame (85) and the Top Frame (4) with two M4 x
12mm Self-tapping Screws (56) and two M4
Washers (77).
34
88
4
85
Attach the Left Shroud (87) to the Base (1) and
the Stabilizer (2) with two M4 x 12mm Self-tapping Screws (56) and two M4 Washers (77).
77
77
56
56
Repeat this step for the Right Shroud (88).
87
Tighten the Nylon Locknut (69) used in
step 33.
2
1
56 77
56
77
35. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in
ADJUSTMENTS, on the next page. Before using the weight system, pull each cable a few times to make
sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and
correct the problem. IMPORTANT: If the cables are not properly routed, they may be damaged when
heavy weight is used. See the CABLE DIAGRAM on page 19 of this manual for proper cable routing. If
there is any slack in the cables, you will need to remove it by tightening the cables; see TROUBLESHOOTING AND MAINTENANCE on page 20.
16
ADJUSTMENTS
This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ATTACHING THE LAT BAR
Attach the Lat Bar (31) to the High Cable (50) with a
Cable Clip (33). Note: The Lat Bar can be attached to
the Low Cable (not shown). Remove the Lat Bar
when performing exercises that do not require it.
50
6
33
39
USING THE Butterfly Arms
To do press arm exercises, push the Press Frame
Lock (39) to the position shown to lock the Right and
Left Arms (6, 7). To do fly exercises, lift the Press
Frame Lock until the Press Arms are free.
31
7
CHANGING THE WEIGHT SETTING
To change the weight setting, insert a Weight Pin (16)
under the desired Weight (15) until the bent end of
the Weight Pin touches the Weights. Turn the bent
end downward. Note: Due to the cables and pulleys, the amount of resistance at each exercise
station may vary from the weight setting. Use the
WEIGHT RESISTANCE CHART on page 18 to find
the approximate amount of resistance at each
weight station.
16
15
REMOVING THE SEAT
Disconnect the Low Cable (48) from the Chain (83).
Remove the M8 Knob (82) and the M8 x 70mm
Carriage Bolt (86). Lift the Seat Frame (8) off the pin
on the Upright (3).
86
3
Pin
8
17
83
48
WEIGHT RESISTANCE CHART
The chart below shows the approximate weight resistance at each exercise station. Weight resistance shown for
the butterfly arm station is for each butterfly arm. Note: The actual resistance at each station may vary due
to differences in individual weight plates as well as friction between the cables, pulleys, and weight
guides.
WEIGHT
PRESS
ARM
(lbs.)
BUTTERFLY
ARM
(lbs.)
HIGH
PULLEY
(lbs.)
LOW
PULLEY
(lbs.)
LEG
LEVER
(lbs.)
1
35
19
26
29
48
2
50
28
38
43
71
3
66
36
53
55
91
4
81
45
68
69
114
5
94
55
80
84
139
6
111
69
98
96
158
7
132
75
116
119
197
8
155
84
127
139
230
9
170
94
139
160
265
10
189
105
155
172
285
11
215
113
171
188
312
Note: 1 lb. = 0.454 kg
18
CABLE DIAGRAMS
The cable diagrams below show the proper routing of the Short Cable (47), the Low Cable (48), the Press
Cable (49), and the High Cable (50). Use the diagrams to make sure that the cables have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly and damage may
occur. The numbers show the correct route for each cable.
5
2
5
1
4
2
4
High Cable (50)
1
3
3
Press Cable (49)
6
Short Cable (47)
2
2
3
Low Cable (48)
4
1
5
1
3
6
19
TROUBLESHOOTING AND MAINTENANCE
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight
system, can stretch slightly when it is first used. If
there is slack in the cables before resistance is felt,
the cables should be tightened.
52
Slack can be removed by moving a 90mm Pulley
(34), the Cable Trap (36), and two Finger Guards (35)
to a set of holes closer to the center of the two Pulley
Plates (44). Remove the M10 Nylon Locknut (68) and
the M10 x 52mm Bolt (52) and re-attach the Pulley,
Cable Trap, and Finger Guards to the new set of
holes in the Pulley Plates with the Bolt and Locknut.
44
35
35
68
36
34
Slack can also be removed by moving the 90mm
Pulley (34), the Cable Trap (36), and two Finger
Guards (35) to the higher set of holes in the “U”-bracket (43). Remove the M10 Nylon Locknut (68) and the
M10 x 52mm Bolt (52) and re-attach the Pulley, the
Cable Trap, and two Finger Guards to the higher set
of holes in the “U”-bracket with the Bolt and Nylon
Locknut.
47
43
71
52
Finally, slack can be removed from the cables by tightening the M8 Washer (71) and M8 Nylon Locknut (69)
attaching the Short Cable (47) to the “U”-bracket (43).
The High Cable (not shown) and the Small “U”-bracket
(not shown) can be adjusted in the same manner.
69
68
35
36
34
35
Make sure that the cables are not too tight or the
Top Weight (not shown) will be lifted off the weight
stack.
20
PART LIST—Model No. WEEVSY2026.0
Key No.
Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
1
1
1
1
1
1
1
1
1
2
1
1
1
2
11
1
2
1
1
2
4
4
2
8
3
4
2
2
2
1
1
2
3
13
20
7
4
2
1
4
2
1
1
2
2
1
Base
Stabilizer
Upright
Top Frame
Press Frame
Right Arm
Left Arm
Seat Frame
Leg Lever
Weight Guide
Small “U”-bracket
Weight Tube
Weight Tube Bumper
Guard
Weight
Weight Pin
Weight Bumper
Backrest
Seat
Arm Pad
Foam Pad
Pad Cap
25mm Round Inner Cap
45mm Square Inner Cap
25mm x 50mm Inner Cap
50mm Square Inner Cap
25mm Round Outer Cap
25mm x 68mm Round Bushing
25mm Washer
Cable Hook
Lat Bar
Handgrip
Cable Clip
90mm Pulley
Finger Guard
Cable Trap
Small Spacer
Pulley Arm
Press Frame Lock
M6 x 16mm Screw
50mm Square Outer Cap
Double “U”-bracket
“U”-bracket
Pulley Plate
Pad Tube
M10 x 100mm Bolt
R0706A
Key No.
Qty.
Description
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
#
#
#
#
1
1
1
1
2
6
5
2
2
8
3
2
2
1
2
1
3
1
4
1
2
24
9
16
4
2
6
2
1
1
9
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Short Cable
Low Cable
Press Cable
High Cable
Large Spacer
M10 x 52mm Bolt
M10 x 46mm Bolt
M10 x 78mm Bolt
M10 x 65mm Bolt
M4 x 12mm Self-tapping Screw
M10 x 70mm Bolt
M8 x 63mm Carriage Bolt
M10 x 65mm Carriage Bolt
M8 x 45mm Bolt
M6 x 43mm Bolt
M10 x 155mm Bolt
M8 x 68mm Bolt
M10 x 125mm Bolt
M6 x 58mm Screw
M8 x 63mm Bolt
M6 x 63mm Screw
M10 Nylon Locknut
M8 Nylon Locknut
M10 Washer
M8 Washer
M6 Nylon Locknut
M6 Washer
25mm Round Thin Cap
Bumper
M4 x 19mm Self-tapping Screw
M4 Washer
Butterfly Grip
Lock
Lock Pin
M10 x 57mm Bolt Set
M8 Knob
Chain
Right Shroud Frame
Left Shroud Frame
M8 x 70mm Carriage Bolt
Left Shroud
Right Shroud
User’s Manual
Exercise Guide
Grease Packet
Hex Key
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
21
EXPLODED DRAWING A—Model No. WEEVSY2026.0
R0706A
25
70
64
27
26
70
27
29
5
49
61
84
63
68
29
53
34
36
69
34
28
55
26
37
4
28
72
6
72
68
52
53
70
68 68
35
68
73
49
24
65
61
20
73
37
85
26
70
34
35
50
7
35
34
23
35
24
73
74
20
65
35
24
73
78
52
36
34
74
35
78
35 44
36
34
22
68
44
35
19
21
45
86
24
47
43
24
82
81
71
52
69
68
8
22
21
76 77
81
9
21
75
40
24
40
30
45
21
22
70
24
22
36
34
35
22
48
68
35
EXPLODED DRAWING B—Model No. WEEVSY2026.0
32
52
31
70
70
10
39
68
66
69
54 35 36
71
25 71
70
68
63
54
38
35
36
34
62
33
R0706A
35
68
56
79
77
68
68
67
18
77
52
70 34 35
69
32
38
50
56
56
73
80
77
60
71
69
35
73 67
11
34
35
68
53
42
68
3
69
12
53
87
88
13
35
68
69
14
70
16
34
35
70
15
14
69
46
34
56
36
70
51
55
77
48
51
56
70
77
77
68
35
34
35
68
56
41
68
70
2
53
68
70
41
68
47
1
57
37 70
17
59
83
57
26
33
58
23
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Tel:
08457 089 009
Outside the UK: 0 (044) 113 387 7133
Fax: 0 (044) 113 387 7125
Please provide the following information when ordering replacement parts:
• the MODEL NUMBER of the product (WEEVSY2026.0)
• the NAME of the product (WEIDER PRO 2000 weight system)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING on
pages 21, 22, and 23)
Part No. 241877 R0706A
Printed in China © 2006 ICON IP, Inc.