Download Snapper 4564 User's Manual
Transcript
Attachment Illustrated Parts List Attachment Mfg. No. Description 1694693 Catcher, Turbo Clean Sweep Twin MANUFACTURING, INC. 500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA www.simplicitymfg.com © Copyright 2007 Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA. Part No.: 1734848 Rev. 04/2007 TP 400-4564-00-AT-SMA Table Of Contents PRODUCT COMPONENTS PAGES Cover & Bag Group - Twin ................................................................................................................................... Hitch Group .......................................................................................................................................................... Tube Group .......................................................................................................................................................... 4 6 8 Torque Specification Chart ..................................................................... Inside Back Cover Cover & Bag Group - Twin 983952 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. The above parts group applies to the following Mfg. Nos.: 1694693 - Catcher Briggs and Stratton Yard Power Products Group Copyright © 2007 by Briggs and Stratton Corporation Milwaukee, WI, USA. All rights reserved 4 TP 400-4564-00-AT-SMA Cover & Bag Group - Twin REF NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 1704615SM 1960381SM 1704075SM 1704135SM 1704508SM 1960399SM 1930642SM 1960096SM 1704507SM 1929000SM 1960077SM 1960252SM 1727129ASM 1727129ASM 1921966SM 1928352SM 1960221SM 1703700SM 1917372SM 1917356SM 1672023ASM 1703807ASM 1931333SM 1703855ASM 1703764SM 1675707SM 1704057SM 1930531SM 1675043SM 1703853SM 1928919SM 2860367SM 1910531SM 1667248SM 1732820SM 1704056SM 1704180SM 1933886SM 1705876SM 1921319SM 1960400SM 1704056SM QTY. DESCRIPTION 1 7 1 1 3 1 5 2 1 2 2 5 1 1 4 4 2 1 4 4 2 2 4 2 2 2 1 2 4 1 2 2 4 6 1 1 2 1 1 1 1 1 TUBE ASSEMBLY Support (Incl. Ref. Nos. 2, 3, 4, 5, 6, 8, 9 & 11) RIVET, Pop SUPPORT, Tube SEAL, Cover BRACKET, Seal SCREW, Round Head, #8-32 x 7/8 LOCKNUT, Flange, 1/4-20 WASHER STRAP, Tube Support SCREW, Taptite, 1/4-20 x 3/8 NUT, Hex, Lock, #8-32 CARRIAGE BOLT, 1/4-20 x 5/8 CROSS ASSEMBLY CROSS ASSEMBLY CAPSCREW, Hex Head, 3/8-16 x 7/8 NUT, Hex, Whizlock, 3/8-16 CLIP, Hairpin SCREEN NUT, Hex, 5/16-18 LOCKWASHER, 5/16 CLAMP HANGER CARRIAGE BOLT, 5/16-18 x 3/4 HOOP, Bag BAG, Grass TUBE CLIP, Grass Bag SEAL, Clip SCREW, Truss Head, #10-32 x 1/2 RIVET, Pop HANDLE, Latch NUT, Hex, #10-32 PIN, Round Head WASHER CLIP, Canoe DECAL, Safety COVER WINDOW NUT, Speed CABLE, Double Loop WASHER, 1/4 SCREW, Self-tapping, #10-12 x 5/8 COVER ASSEMBLY (Incl. Ref. Nos. 17, 26, 28, 32, 37, 38, 39 & 40) Footnotes The above parts group applies to the following Mfg. Nos.: 1694693 - Catcher Briggs and Stratton Yard Power Products Group Copyright © 2007 by Briggs and Stratton Corporation Milwaukee, WI, USA. All rights reserved 5 TP 400-4564-00-AT-SMA Hitch Group 986032 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. The above parts group applies to the following Mfg. Nos.: 1694693 - Catcher Briggs and Stratton Yard Power Products Group Copyright © 2007 by Briggs and Stratton Corporation Milwaukee, WI, USA. All rights reserved 6 TP 400-4564-00-AT-SMA Hitch Group REF NO PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1960462SM 1924361SM 1668662SM 1960355SM 1916950SM 1916965SM 1707526ASM 1921210SM 1703744ASM 1723067ASM 1920415SM 1723044ASM 1960033SM 1931348SM 1723065SM 1723064ASM 1917372SM 1917356SM 1729281SM 1960236SM 1960223SM 1707526ASM QTY. DESCRIPTION 4 4 4 4 6 6 1 6 1 2 6 2 2 4 1 1 2 2 2 2 2 1 CAPSCREW, Hex Head, 1/2-13 x 2-1/2 WASHER SPACER LOCKNUT, Hex, 1/2-13 NUT, Hex, 3/8-16 LOCKWASHER, 3/8 SUPPORT, Upright CAPSCREW, Hex Head, 3/8-16 x 1 BRACKET, Lower Hitch SUPPORT, Side Hitch CAPSCREW, Hex Head, 3/8-16 x 1-1/4 PLATE, Side CLIP, Hair Pin CARRIAGE BOLT, 3/8-16 x 3/4 CLAMP, Hitch CLAMP, Plate NUT, Hex, 5/16-18 LOCKWASHER PIN, Round Head, Drilled SPACER CARRIAGE BOLT, 5/16-18 x 1-1/4 SUPPORT, Upright Footnotes The above parts group applies to the following Mfg. Nos.: 1694693 - Catcher Briggs and Stratton Yard Power Products Group Copyright © 2007 by Briggs and Stratton Corporation Milwaukee, WI, USA. All rights reserved 7 TP 400-4564-00-AT-SMA Tube Group T986032 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. The above parts group applies to the following Mfg. Nos.: 1694693 - Catcher Briggs and Stratton Yard Power Products Group Copyright © 2007 by Briggs and Stratton Corporation Milwaukee, WI, USA. All rights reserved 8 TP 400-4564-00-AT-SMA Tube Group REF NO PART NO. 1 2 4 5 6 7 8 9 10 1933896SM 1960096SM 1704283SM 1960404SM 2810542SM 1705063SM 1707712SM 1960252SM 1930641SM QTY. DESCRIPTION 2 6 1 2 2 1 1 1 1 NUT, Hex Nylock, #10-32 WASHER ELBOW, Upper SCREW, Truss Head, #10-32 x 1/2 RIVET CLIP, Spring TUBE & SPRING ASSEMBLY (Incl. Ref. Nos. 2, 6, & 7) CARRIAGE BOLT, 1/4-20 x 5/8 NUT, Hex Flange Lock, 1/4-20 Footnotes The above parts group applies to the following Mfg. Nos.: 1694693 - Catcher Briggs and Stratton Yard Power Products Group Copyright © 2007 by Briggs and Stratton Corporation Milwaukee, WI, USA. All rights reserved 9 TP 400-4564-00-AT-SMA Hardware Identification & Torque Specifications Common Hardware Types Torque Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Washer Hardware Grade Lockwasher Carriage Bolt No Marks SAE Grade 2 Hex Nut Size Of Hardware Standard Hardware Sizing 8-32 8-36 10-24 10-32 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 7/16-14 7/16-20 1/2-13 1/2-20 9/16-12 9/16-18 5/8-11 5/8-18 3/4-10 3/4-16 7/8-9 7/8-14 1-8 1-12 When a washer or nut is identified as 1/2”, this is the Nominal size, meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2 - 16 x 2”, this means the Nominal size, or body diameter is 1/2 inch; the second number represents the threads per inch (16 in this example, and the final number is the body length of the bolt or screw (in this example 2 inches long). The guides and ruler furnished below are designed to help you select the appropriate hardware and tools. 0 1/4 Nut, 1/2” 1/2 Inside Diameter 3/4 1 1/4 1/2 3/4 Screw, 1/2 x 2 2 1/4 Body Diameter in/lbs ft/lbs 19 20 27 31 66 76 11 12 20 23 30 35 50 55 65 75 90 100 160 180 140 155 220 240 Nm. 2.1 2.3 3.1 3.5 7.6 8.6 15.0 16.3 27.2 31.3 40.8 47.6 68.0 74.8 88.4 102.0 122.4 136 217.6 244.8 190.4 210.8 299.2 326.4 SAE Grade 5 in/lbs ft/lbs 30 31 43 49 8 10 17 19 30 35 50 55 75 90 110 120 150 180 260 300 400 440 580 640 SAE Grade 8 Nm. in/lbs ft/lbs Nm. 3.4 3.5 4.9 5.5 10.9 13.6 23.1 25.8 40.8 47.6 68.0 74.8 102.0 122.4 149.6 163.2 204.0 244.8 353.6 408.0 544.0 598.4 788.8 870.4 41 43 60 68 12 14 25 27 45 50 70 80 110 120 150 170 220 240 386 420 600 660 900 1,000 4.6 4.9 6.8 7.7 16.3 19.0 34.0 34.0 61.2 68.0 95.2 108.8 149.6 163.2 204.0 231.2 299.2 326.4 525.0 571.2 816.0 897.6 1,244.0 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. 1/2 Body Length 3/4 3 1/4 1/2 3/4 4 Wrench & Fastener Size Guide 1/4 5/16 3/8 1/4” Bolt or Nut Wrench—7/16” 5/16” Bolt or Nut Wrench—1/2” 3/8” Bolt or Nut Wrench—9/16” 7/16 DIA. 7/16” Bolt or Nut Wrench (Bolt)—5/8” Wrench (Nut)—11/16” 1/2 DIA. 1/2” Bolt or Nut Wrench—3/4”