Download Sharp AR-M350U/M450U User's Manual

CODE : 00ZARM350UA1E
LASER PRINTER
AR-M350U/M450U
MODEL AR-M350N/M450N
OPTIONS
AR-P14
[1] INTRODUCTION
The AR-M350U/M450U and AR-M350N/M450N are minor change models based on the AR-M350/M450.
This service manual only provides information on these minor changes.
In addition to this service manual, the documents listed below are required to properly maintain these machines.
•AR-M350/M450
Service Manual : 00ZARM350/A1E
Parts Guide : 00ZARM450/P1E
Circuit Diagram : 00ZARM350/C1/
•AR-P350/P450
Service Manual : 00ZARP350/A2E
Parts Guide : 00ZAR350LPP1/
Circuit Diagram : 00ZARP350/C1/
•AR-NC5J
Service Manual : 00ZARNC5J/A1E
Note: Depending on the option, additional service documentation may be required.
[2] LIST OF DIFFERENCES FROM AR-M350/M450
A.Product composition
Printer Option Model
NIC Standard Model
Base Engine
Model Name
AR-M350U
AR-M450U
AR-M350N
AR-M450N
Print Speed
35ppm
45ppm
35ppm
45ppm
Multi Function Controller
Multi Function Controller(for U-Model)
Print Server Card
Printer Extension Kit
AR-M11
Not Available
Standard
Not Available
Standard
Not Available
AR-NC5J
Not Available
Standard
AR-P14
Option
Not Available
Note
Not registered as a product
*1
*1: Installation of the AR-P14 on the AR-M350U/M450U will provide similar functionality to that of the AR-M350/M450.
Parts marked with “ “ are important for maintaining the safety of the set.
Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
!"#"$
[3] CONFIGURATION
1.System Configurations
Exit tray
(AR-TE3 or AR-DU4 Standard)
B/W scanner module/DSPF(AR-EF1)
Duplex
module/bypass
tray(AR-DU4)
Finisher
(AR-FN6)
Upper exit tray
extension
(AR-TE4)
Duplex module
(AR-DU3)
Mail-bin stacker
(AR-MS1)
Saddle stitch
finisher
(AR-FN7)
Stand/3 x 500 sheet
paper drawer
(AR-D14)
Power supply unit
(AR-DC1)
Stand/MPD & 2000 sheet
paper drawer
(AR-D13)
2. Standard
Category
Model Name
MFP model (35ppm)
AR-M350
MFP model (45ppm)
AR-M450
MFP model (35ppm)
AR-M350U
MFP model (45ppm)
(Without network printer function)
AR-M450U
MFP model (35ppm)
(With NIC card (standard))
AR-M350N
MFP model (45ppm)
AR-M450N
Other options required for the installation/mounting.
(Options must be ordered separately.)
• B/W Scanner module/DSPF (AR-EF1)
• Scanner Rack(AR-RK1)
• Stand/MPD&2000 sheet paper drawer (AR-D13) or Three paper drawer stand
(AR-D14)
• Power supply unit (AR-DC1)
AR-M350U CONFIGURATION 3-1
Remarks
% !"#"$
3. List of combination of peripheral devices
A.AR-M350U/M450U
As shown in the table below, some other peripheral devices ( B ) may be needed for installation of a peripheral device ( A ) and some peripheral devices
cannot be installed together.
B/W scanner module/DSPF
AR-EF1
Scanner rack
AR-RK1
Power supply unit
Hard disk drive
Network printer kit
Network scanner expansion kit
Facsimile expansion kit
Fax memory (8 MB)
PS3 expansion kit
Multi-function controller board
Print server card
Upper exit tray extension
Punch unit
Exit tray
Mail-bin stacker
Finisher
Duplex module
Saddle stitch finisher
Duplex module/bypass tray
Stand/MPD & 2000 sheet
Stand/3 x 500 sheet paper drawer
B/W scanner module/DSPF
Related for scanner feature
Scanner rack
B
*1
*1
Related for paper feed unit
Stand/3 x 500 sheet
paper drawer
AR-D14
Stand/MPD & 2000 sheet
paper drawer
AR-D13
Duplex module/bypass tray AR-DU4
*1
*2
Duplex module
AR-DU3
*1
*2
*1
Finisher
AR-FN7
AR-FN6
Mail-bin stacker
AR-MS1
*1
Output units
Saddle stitch finisher
A
Exit tray
*1
*1
*4 AR-TE3
Upper exit tray extension
AR-TE4
Punch unit
AR-PN1
*1
Related for extension of
functions and others
PS3 expansion kit
AR-PK1
Network scanner
expansion kit
AR-NS2
Facsimile expansion kit
Fax memory (8 MB)
AR-FX5
*1
AR-MM9
*1
Power supply unit
AR-DC1
*1
Hard disk drive
AR-HD3
Multi-function controller
*5 AR-M11
board
Print server card
Network printer kit
*1
*1
*1
*6 AR-NC5J
AR-P14
= Must be installed together.
*1 = Any of the units must be installed together.
*2 = Must be installed for installation of the stand/3 x 500 sheet paper drawer or
the stand/MPD & 2000 sheet paper drawer.
= Cannot be installed together.
*3 = Standard
*4 = AR-DU4 Standard
*5 = Attachment of the AR-P14 provides the similar functions.
*6 = Not Available
AR-M350U CONFIGURATION 3-2
*1
!"#"$
B.AR-M350N/M450N
As shown in the table below, some other peripheral devices ( B ) may be needed for installation of a peripheral device ( A ) and some peripheral devices
cannot be installed together.
B/W scanner module/DSPF
AR-EF1
Scanner rack
AR-RK1
*1
*1
Related for paper feed unit
Stand/3 x 500 sheet
paper drawer
AR-D14
Stand/MPD & 2000 sheet
paper drawer
AR-D13
Duplex module/bypass tray AR-DU4
*1
*2
1
*2
AR-DU3
*
*1
Finisher
AR-FN7
AR-FN6
*1
Mail-bin stacker
AR-MS1
*1
Duplex module
Output units
Saddle stitch finisher
A
Exit tray
*1
*4 AR-TE3
Upper exit tray extension
AR-TE4
Punch unit
AR-PN1
*1
Related for extension of
functions and others
PS3 expansion kit
AR-PK1
Network scanner
expansion kit
AR-NS2
Facsimile expansion kit
Fax memory (8 MB)
AR-FX5
*1
AR-MM9
*1
Power supply unit
AR-DC1
*1
Hard disk drive
AR-HD3
Multi-function controller
*3 AR-M11
board
Print server card
Network printer kit
*1
*1
*3 AR-NC5J
*6 AR-P14
= Must be installed together.
*1 = Any of the units must be installed together.
*2 = Must be installed for installation of the stand/3 x 500 sheet paper drawer or
the stand/MPD & 2000 sheet paper drawer.
= Cannot be installed together.
*3 = Standard
*4 = AR-DU4 Standard
*6 = Cannot be attached.
AR-M350U CONFIGURATION 3-3
Hard disk drive
Network printer kit
Power supply unit
Network scanner expansion kit
Facsimile expansion kit
Fax memory (8 MB)
PS3 expansion kit
Multi-function controller board
Print server card
Punch unit
Upper exit tray extension
Exit tray
Mail-bin stacker
Finisher
Duplex module
Saddle stitch finisher
Duplex module/bypass tray
Stand/MPD & 2000 sheet
Stand/3 x 500 sheet paper drawer
B/W scanner module/DSPF
Related for scanner feature
Scanner rack
B
!"#$
[4] SPECIFICATIONS
(in mm)
1. Basic Specification
A
B
C
D
E
A3
297
420
4
289
4
A. Base Engine (AR-M350U/M350N/M450U/M450N)
B4
257
364
4
242
4
A4
210
297
4
202
4
B5
182
257
4
168
4
A5
148
210
4
140
4
Japanese postcard
100
148
4
92
4
Ledger
279
432
4
271
4
4
Paper size
(1) Form
AR-M350U/M350N/M450U/M450N Console type
(2) Engine speed
Paper size
AR-M350U/N
AR-M450U/N
A4, 8.5" x 11"
35ppm
45ppm
Legal
216
356
4
208
A5R/5.5" x 8.5"R
35ppm
45ppm
Foolscap
216
330
4
208
4
B5
35ppm
45ppm
Letter
216
279
4
208
4
B4/8.5" x 14
20ppm
22ppm
Executive
184
267
4
183
4
A3/11" x 17"
17ppm
20ppm
Invoice
140
216
4
132
4
(3) Engine composition
Photoconductor type
Record method
Development method
Charge method
Transfer method
Cleaning method
Fusing method
Used toner disposal
OPC (diameter of photoconductor : ø30mm)
Electrophotograph (laser)
Dry-type dual-component magnetic brush
development
Charged saw-tooth method
Transfer roller
Counter blade
Heat roller
Toner recycling system
Com-10(envelope)
105
241
4
97
4
C5(envelope)
162
229
4
154
4
Monarch(envelope)
98
191
4
90
4
DL(envelope)
110
220
4
102
4
ISO B5(envelope)
176
250
4
168
4
(6) Warm-up
Warm-up time
Pre-heat requirement
Jam recovery time
(4) Engine resolution
Resolution
Smoothing
Gradation
Write :600dpi
Write :1200dpi equivalent
Write :2 levels
less than 80 seconds
Required
Target: about 30 seconds
(Under standard condition of 60 seconds left
after side cover opening, polygon motor halt)
(7) Power source
Voltage
(5) Printable area
100V system
100-127V
50/60Hz
Frequency
The print area of this product is shown below.
200V system
220-240V
50/60Hz
(8) Power consumption
E
AR-M350U/N
Max. Power consump.
C
C
1440W
AR-M450U/N
1440W
(9) Energy Star benchmark
AR-M350U/N
B
AR-M450U/N
Low power mode
40W
75W
Transition time to Low power mode
60min
60min
(10) Noise
AR-M350U/N
AR-M450U/N
At working
less than 6.8B
less than 6.8B
At waiting mode
less than 5.0B
less than 5.0B
*
Showing noise benchmark in each model as a whole system.
(11) Dimensions
E
External dimensions
(WxDxH)
Occupied space
dimensions
(WxD)
Weight
D
A
Paper size
Printable area
If a printer driver for Windows or Macintosh is used for printing, the
printable area will be smaller. The actual printable area depends on the
printer driver to be used.
*1:
428x552x469 (Only main unit) (mm)
16.9"x21.7"x18.5"
963x685 (mm) *1
25.7"x22.3"
AR-M350U/M450U:Approx.38.9kg
(Only main unit)
Approx.99kg *1
AR-M350N/M450N:Approx.39.9kg
(Only main unit)
Approx.100kg *1
With B/W scanner module/DSPF, Scanner rack, Large capacity
paper feed desk, Power supply unit and Upper exit tray extension
AR-M350U SPECIFICATIONS 4-1
% !"#$
B. Document Feeding Equipment
(4) Print Function
(1) One-drawer tray (included in the base engine)
a. General
Paper feed method
Sizes to be fed
Paper capacity
Media available for
paper feeding
Paper type
Paper size switching
Dehumidification
heater
Balance detection
Default size setting
Mounting/demounting
of the tray
One-drawer tray
A4, B5, 8.5" x 11"
500 sheets (at 80g/m²)
Plain paper 60 - 105g/m², 16 - 28lbs
Plain, recycled, pre-printed, pre-punched,
color, letter head
To be switched by user
(paper size to be entered from the operation
panel).
Not provided
Provided (paper empty and 3 steps)
100V system
200V system
8.5" x 11"
A4
Provided
When an optional PS3 expansion kit is
installed
Function
PCL5e/
PCL6
PS
PPD
(Windows)
PPD
(Macintosh)
Copies
1 - 999
1 - 999
1 - 999
1 - 999
Orientation
Yes
Yes
Yes
Yes
Duplex print
Yes
Yes
Yes
Yes
Saddle stitch
Yes
Yes
No
N/A
Binding edge
Left/top/
right
Left/top/
right
Long/short
Long/short
N-up
2/4/6/8
2/4/6/8
2/4*3*4
2/4/6/9/16
N-up direction
Fixed
Fixed
Fixed
Selectable
N-up border line
Yes
Yes
Yes(always) Yes
b. Paper input
When an optional PS3 expansion kit is
installed
C. Output Equipment
(1) Face-down Exit Tray (included in the base engine)
Output position/
method
Output paper capacity
Output paper size
Spec of media for
paper output
Remaining paper
detection
Exit tray full detection
Face-down output at the upper side of main
unit
400 sheets (80g/m² sheet)
A3, B4, A4, A4R, B5, B5R, A5R
11 " x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11 ",
8.5" x 11 "R, 5.5" x 8.5"R
Executive, postal card, Monarch (98 x 191)
Com-10 (105 x 241), DL (110 x 220),
C5 (162 x 229), ISO B5 (176 x 250)
Tracing paper : 52 ~ 59g/m² / 14 ~ 15lbs
Plain paper : 60 ~ 128g/m² / 16 ~ 34lbs
Index paper : 176g/m² / 47lbs
Cover paper : 205g/m² / 54 ~ 55lbs
Transparency firm
Not provided
Provided
2. Specific Function
Function
PCL5e/
PCL6
Yes
Yes
Yes
Yes
Custom paper size
1 size
1 size
3 sizes*3*5
N/A
Source selection
Yes
Yes
Yes
Yes
Different first page
Yes
Yes
N/A
Yes
Transparency inserts Yes
Yes
N/A
Yes
c. Paper output
When an optional PS3 expansion kit is
installed
Function
PCL5e/
PCL6
PS
PPD
(Windows)
PPD
(Macintosh)
Output tray selection Yes
Yes
Yes
Yes
Mail bin
Yes
Yes
Yes
Yes
Staple
Yes
Yes
Yes
Yes
Offset
Yes
Yes
Yes
Yes
Punch
Yes
Yes
Yes
Yes
When an optional PS3 expansion kit
is installed
IBM PC/AT (Include compatible machine)
Macintosh (680x0), Power Macintosh, iMac, G3Macintosh
For Macintosh OS, the PS3 expansion kit and NIC card are required.
(2) Support OS
Custom
PCL5e/6(XL)
SPDL
PPD
*
PPD
(Macintosh)
d. Graphic
(1) Platform
Custom PS
PPD
(Windows)
Paper size
A. Printer Function
*
PS
Windows 95/98/Me/XP
Windows NT 4.0
Windows 2000
Windows 95/98/Me/XP
Windows NT 4.0
Windows 2000
Windows 95/98/Me/XP
Windows NT 4.0
Windows 2000
Mac OS 8.5.1 - Mac OS 9
For Macintosh OS, the PS3 expansion kit and NIC card are required.
Function
PCL5e/
PCL6
PS
PPD
PPD
(Windows) (Macintosh)
Resolution
600/300
dpi
600 dpi
600 dpi
600 dpi
Halftone
N/A
Yes
Yes
N/A
Graphic mode
Yes
N/A
N/A
N/A
Smoothing
Yes
Yes
Yes
Yes
Toner save
Yes
Yes
Yes
Yes
Photo enhancement
Yes*8
Yes
N/A
N/A
Negative image
N/A
Yes
Yes
Yes
Mirror image
N/A
Horizontal/
vertical
Horizontal Yes
Zoom
N/A
N/A
Yes
Yes
Fit to page
Yes
Yes
N/A
N/A
(3) PDL emulation
PCL6, PCL5e compatible,
PostScript Level 2, PostScript 3 compatible
(PS3 expansion kit is required.)
AR-M350U SPECIFICATIONS 4-2
!"#$
B. Expanded RAM
e. Font
When an optional PS3 expansion kit is
installed
Installation of an expanded RAM will avoid the following status.
1) Time out error reduction
2) Spool time reduction
3) Avoidance of VM error / memory full
Function
PCL5e/
PCL6
PS
PPD
PPD
(Windows) (Macintosh)
Resident font
45 fonts
136 fonts
136
fonts*6
35 fonts
Download font
Bitmap
TrueType,
Graphic
Bitmap
Type1
TrueType
Bitmap
Type1
TrueType
N/A
Use commercially available RAM with the following specifications.
Note: If RAM used does not meet the follow specifications, the copier
may not recognize the additional RAM or its capacity correctly.
f. Others
When an optional PS3 expansion kit is
installed
<Spesification>
DIMM TYPE
168pin 3.3V Unbuffered SDRAM DIMM Non-ECC
DIMM capacity
64MByte, 128MByte, 256MByte
CAS LATENCY
CL=2
Function
PCL5e/
PCL6
PS
PPD
PPD
(Windows) (Macintosh)
Watermark*7
Yes
Yes
Yes
Yes
Overlay
Yes
Yes
N/A
N/A
Job retention*1
Yes
Yes
N/A
Yes
SDRAM CLOCK For PC100, PC133
SPD
Supporting
Parity
Not support
ECC
Not support
Account control Yes
Yes
N/A
Yes
Custom settings Yes
Yes
N/A
N/A
Automatic
configuration*2
Yes
Yes
N/A
Yes
<Operation-assured Memory> (As of March / 2001)
Job end
notification
Yes
Yes
N/A
N/A
Kingston
Technology
Manufacture Capacity
* 1 In the models without a hard disk drive, an optional hard disk drive
must be installed .
* 2 Functions when peripheral devices are installed.
* 3 Not supported in the Windows NT 4.0 environment.
* 4 2/4/6/9/16 is supported in the Windows 2000 environment.
* 5 Only one size is supported in the Windows 2000 environment.
* 6 Only 35 fonts are supported in the Windows NT 4.0 environment.
* 7 This function is limited for PPD.
* 8 PCL6 only
Model name
KVR133X64C3/
128
HYB39S64800BT
-7.5
128MB
KVR133X64C3
-128
D456821G-A75
-9JF
256MB
KVR133X64C3
-256
HY57V28820AT-H
Viking
64MB
Compornents
VIK8641CL2
µPD456841G5
-A80-9JF
64MB
VIK8641CL2
D456841G5-A80
-9JF
128MB
VIK6642CL2
TC59SM708FT-80
128MB
VIK6642CL2
D4564841G5-A80
-9JF
VIK2642CL2
TC59SM708FT-80
(5) Compatibility
PCL 5e
compatibility
PCL6
compatibility
PostScript
Compatibility
Target for PCL5e is to be compatible with HP LaserJet
4000.
Small margin difference, rendering difference by
different font family, default and transfer function
difference are not to be included in the compatibility.
All the PJL commands are not necessarily included in
the compatibility.
Target for PCL6 is to be compatible with HP LaserJet
4000.
Small margin difference, rendering difference by
different font family, default and transfer function
difference are not to be included in the compatibility.
All the PJL commands are not necessarily included in
the compatibility.
Roman PostScript is targeted to be compatible with
Adobe PostScript as performed in HP LaserJet 4000.
Small margin difference, rendering difference by
different font family, default and transfer function
difference are not to be included in the compatibility.
RAM CHIP name
128MB
256MB
Memory Card 64MB
Technology
128MB
Note
DM864VS65804X GM72V66841XT75
-7G
DM1665VS65804 HY57V64820HG
X-7G
C. Scanner function
*Scanner function, the NIC card and Network Scanner kit are required.
(1) Scanner function
Scanner mode
Scan to E-mail (Internet FAX)
Scan to Server (Client PC)
(2) Support System
Embedded server
Protocol
SMTP server
FTP server
TCP/IP
(3) Support Image
Format
Compression method
TIFF, PDF, TIFF-F
* Selectable for each page
Uncompressed, G3(1-dimension) *1, G4 *2
*1 G3 (1-dimension) = MH (Modified Huffman)
*2 G4 = MMR (Modified MR)
(4) Transmission Mode
DSPF/OC
Available
transmission switching (Switching during the reading is not feasible)
AR-M350U SPECIFICATIONS 4-3
!"#$
(5) Image Process
Half tone reproduction
Exposure adjustment
Quality selection
Resolution*
D. Copy function
Equivalent to 256 levels
Light / Auto / Dark
Half-tone ON/OFF
Normal ( 200x200dpi )
Fine ( 300x300dpi )
Super fine ( 400x400dpi )
Ultra fine ( 600x600dpi )
Varies with the file type/transmission method
(1) Copy Speed
AR-M350U/N
AR-M450U/N
Actual Reduction Enlargement Actual Reduction Enlargement
A4,
8.5"x11"
35
35
35
45
45
45
A4R,
8.5"x11"R
25
25
25
30
30
30
A5R,
5.5"x8.5"R,
Invoice-R
35
35
35
45
45
45
(7) Specified Destination
B5
35
35
35
45
45
45
Specified destination
One-touch*
B5R,
Exective-R
25
25
25
30
30
30
B4,
8.5"x14"
20
20
20
22
22
22
A3,
11"x17"
17
17
17
20
20
20
Extra,
Envelope
17
17
17
20
20
20
(6) Original Memory
Standard
Memory expansion
Group*
Program
Commonly use ERDH area of memory.
Special : As per ERDH memory
Specifying by one-touch or group
Max. 500 destinations
(in conjunction with the one-touch dial of FAX)
Max. 100 destinations can be registered
for FTP and Desktop.
To be registered in one-touch
Available
(8) Specified Multiple Destinations
Specified destination Specifying by one-touch or group
No. of registration
Max. 300 items
(in conjunction with those of FAX)
Sequential
Available
broadcasting
(E-mail only. It is not available for FTP/Desktop.)
Simultaneous FAX
Available
transmission
(Specifying multiple destinations of FAX, E-mail or FTP
and broadcasting by a single scan)
O : Available
Japan P/C In case of printing on post card, engine speed can vary with system
configuration, because next paper is fed after machine completely output
previous page.
*
Figures in reduction/enlargement are represented by those at the
ratio to show slowest speed
(2) First Copy Time
Conditions: A4 or 8.5"x11"P from front tray of PPC, without HDD and
with polygon motor running.
(9) Functions
Transmitting Rotating transmission
functions
Report/list
functions
Long length original
transmission
Verification stamp function
Transmit/receive record
Transmit/receive result
Address/phone directory
list
Group list
ID/sender list
Program list
AR-M350U/N
Available
(to be matched with FAX
specification)
Not Available
Option
Available
Available
Available
Available
Available
Available
AR-M450U/N
Document glass *1
Less than 5.3 seconds Less than 4.6 seconds
DSPF
Less than 6.0 seconds Less than 5.3 seconds
*1
During OC/high-speed mode
(3) Job Speed
AR-M350U/N
AR-M450U/N
S
S
*1
33 cpm (94%)
42 cpm (93%)
S
D
*2
32 cpm (91%)
40 cpm (88%)
D
D
*3
32 cpm (91%)
40 cpm (88%)
*1 S
*2 S
*3 D
S : A4 / 8.5" x 11"P
D : A4 / 8.5" x 11"P
D : A4 / 8.5" x 11"P
original 5 sheets
copy 5sets
original 10 sheets
copy 5sets
original 5 sheets (10 pages) copy 5sets
Note: First copy time has been factored into calculation resulting in
reduced CPM.
(4) Continuous Copy
Max. multiple number
999 pages
(5) Copy Ratio
Copy ratio
AB series :
25%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 400%
Inch series :
25%, 64%, 77%, 100%, 121%, 129%, 400%
Zoom
25 - 400%
25 - 200% (Copy from DSPF)
Independent Not provided
scaling
(6) Exposure/Copy Quality Process
Exposure mode
Manual steps
Smoothing
Toner save mode
AR-M350U SPECIFICATIONS 4-4
Binary: Text(auto/manual), Text/photo, Photo
256 levels: Not provided
9 steps
Standard
Standard
' !"#$
(7) Copy Function
Function APS
AMS
Paper type select
Special
function
Standard Function
Standard Function
Standard Function
(By type setting)
Auto tray switching
Standard Function
Rotation copy
Standard Function
Electronic sort
Standard Function
Rotation sort
Not provided
Reserved copy
Standard Function
Prior tray setting
Not provided
Recall/register of program
Standard Function
Proof copy
Not provided
Preheat function
Standard Function
(To be set up by key
operator)
Auto power shut-off function
Standard Function
(To be set up by the key
operator program)
Account control
Standard Function
(100 accounts)
Communication support (RIC)
Standard Function
Card counter support
Only
provided the connector
Coin vendor support
Only
provided the connector
Margin shift
Standard Function
Edge erase / Center erase
Standard Function
Dual page copying
Standard Function
Covers
Not provided
Transparency insert
Not provided
Centering
Not provided
Multi shot (N in 1)
Standard Function
(2 in 1 / 4 in 1)
Pamphlet copy
Standard Function
2-sided copy orientation change Standard Function
Large capacity original mode
0 (Max. 140 pages)
B/W reverse
Not provided
Shading
Not provided
Mirror image
Not provided
Repeat
Not provided
Date stamp
Not provided
Stamp
Not provided
Page stamp
Not provided
Zaurus print
Not provided
AR-M350U SPECIFICATIONS 4-5
"
#$%&'(
[5] CONSUMABLE PARTS
1.Supply system table
Note: The consumable parts are the same as those of the AR-M350/M450 and the AR-P350/P450.
A.USA
NO
Name
1 Toner CA(Black)
2
3
4
Developer
Drum
50K maintenance kit
5
100K maintenance kit
6
Upper heat roller kit
7
Lower heat roller kit
8
9
Cleaner blade
Cleaning roller
Content
Toner(Toner : Net Weight 814g)
Life
27K
10 Staple cartridge
Developer(Developer : Net Weight 450g)
Drum
Cleaner blade
Drum separation pawl
Screen grid
Toner reception seal
Side malt F
Side malt R
Charging plate
Transfer roller
Discharging plate
Paper dust removing unit
DV blade
DV side seal F
DV side seal R
Upper heat roller
Fusing separation pawl (Upper)
Lower heat roller
Fusing separation pawl (Lower)
Cleaner blade
Cleaning roller
Bearing
Staple cartridge
x1
x1
x4
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x4
x1
x2
x10
x10
x20
x3
11 Staple cartridge
Staple cartridge
x3
100K
50K
50K
Product name
Remark
AR-450NT
*Life setup is based on A4 6%
(*1 AR-450NT-J)
AR-450ND
AR-450DR
AR-450KC1
100K
AR-450KA1
200K
AR-450UH
200K
AR-450LH
50K(x10) AR-450CB
200K(x10) AR-450CR
AR-450CB=(AR-450BL)x10
AR-450CR=(AR-450RC)x10
3000x3
AR-SC1
5000x3
AR-SC2
Common with cartridge for AR-FN4 &
AR-FN6
Common with cartridge for AR-FN7
*1: For USA Government
Note1: Print on Master/individual carton:Toner/Developer in 2 languages (English/French), DR in 4 languages (English/French/German/Spanish).
Note2: Packed with machine: DR 50K/Developer UN/Process UN
Note3: The other maintenance parts which are not listed above are registered as service parts.
B.Europe
NO
1
2
3
4
Name
Toner CA(Black)
Developer
Drum
50K PM kit
5
100K PM kit
6
200K PM kit
7
Staple cartridge
Content
Toner(Toner : Net Weight 814g)
Developer(Developer : Net Weight 450g)
Drum
Cleaner blade
Drum separation pawl
Screen grid
Toner reception seal
Side malt F
Side malt R
Charging plate
Transfer roller
Discharging plate
Paper dust removing unit
DV blade
DV side seal F
DV side seal R
Upper heat roller
Lower heat roller
Fusing separation pawl (Upper )
Fusing separation pawl (Lower)
Cleaning roller
Bearing
Staple cartridge
8
Staple cartridge
Staple cartridge
x1
x1
x4
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x4
x2
x1
x2
x3
x3
Life
27K
100K
50K
50K
Product name
AR-450T
AR-450DV
AR-450DM
AR-450KC
100K
AR-450KA
200K
AR-450KB
3000x3
AR-SC1
5000x3
AR-SC2
Note1: Print on Master/individual carton:4 languages (English/French/German/Spanish).
Note2: Packed with machine: DR 50K/Developer UN/Process UN
Note3: The other maintenance parts which are not listed above are registered as service parts.
AR-M350U CONSUMABLE PARTS 5-1
Remark
*Life setup is based on A4 6%
Common with cartridge for AR-FN4 &
AR-FN6
Common with cartridge for AR-FN7
"#
$%&'(
2.Production number identification
A. Drum cartridge
C. Developer
The lot number, printed on the front side flange, is composed of 10 digits,
each digit showing the following content:
The lot number is composed of 8 digit, and each digit indicates as
following.
The lot number shall be printed on the bag.
1
2
3
4
5
6
7
8
9
10
1
1
2
3
4
5/6
7
8/9
10
Number
For this model, this digit is 2.
Alphabet
Indicates the model conformity code. T for this model.
Number
Indicates the end digit of the production year.
Number or X, Y, Z
Indicates the production month.
X stands for October, Y November, and Z December.
Number
Indicates the production day on the month.
Number or X, Y, Z
Indicates the month of packing.
X stands for October, Y November, and Z December.
Number
Indicates the day of the month of packing.
Alphabet
Indicates the production factory. "A" for Nara Plant.
1
2
3/4
5/6
7
8
2
3
4
5
6
7
Alphabet
Indicates the production factory.
Figure
Indicates the production year.
Figure
Indicates the production month.
Figure
Indicates the production day.
Hyphenation
Figure
Indicates the production lot.
3. Environmental conditions
A. Operating conditions
30
85%
B. Toner cartridge
The lot number is composed of 7 digits, and each digit indicates as
following.
The lot number shall is printed in the position shown below.
1
2
3
4
5,6
7
2
3
4
5
6
7
Version number (A - sequentially revised)
Numeral figure
Indicates the end digit of the production year.
Alphabet
Indicates the production factory. (B for SOCC)
Destination code
Numeral figures
Indicates the production day.
Numeral figure or X, Y, Z
Indicates the production month.
X stands for October, Y November, and Z December.
35
60%
20
10
35
Temperature
(Without dew condensation)
B. Storage conditions
90
Humidity (%)
1
Humidity (%)
85
Lot No. Location
20
-10
Temperature
40
(Without dew condensation)
Lot No. Location
Heat seal
Aluminum bag
AR-M350U CONSUMABLE PARTS 5-2
8
"
#$%&'
[6] UNPACKING AND INSTALLATION
1. Installing procedure flowchart
There are many combinations between this machine and option units. For installing option units, observe the following procedures for efficiency.
To install the devices efficiently, follow the procedure below.
Some peripheral devices may have been installed as standard devices depending on the main unit model.
Part of descriptions and illustrations may be different.
Scanner/document feeder device
Finishing device
Scanner/document feeder device
Finishing device
Duplex/bypass device
Finishing device
Main unit
Duplex device
Main unit
Paper feeding device
Paper feeding device
Start of installation
Install controller board,
facsimile unit or other electric
devices.
Main unit, paper feeding
device, and power supply
unit.
Controller board,
facsimile unit or other
electric devices
installed?
AR-D13 /AR-DC1
AR-D14 /AR-DC1
Main unit
Yes
No
AR-HD3
AR-FX5/AR-MM9
AR-PK1
AR-NS2
AR-NC5J
(Not required for the AR-M350N/M450N)
AR-P14
(Only AR-M350U/M450U)
[Electrical setting/adjustment]
Install duplex/pypass device.
Duplex/bypass
device installed?
Yes
AR-DU3
AR-DU4
No
Yes
AR-MS1/AR-DC1
AR-FN6 /AR-DC1
AR-FN7
AR-PN1A / B / C / D
No
Scanner/document
feeder installed?
No
*
Main unit/AR-EF1/AR-NC5J/AR-HD3/
AR-FX5/AR-PK1/AR-NS2/AR-P14
2) Paper guide position adjustment/off center adjustment
Install finishing device.
Finishing device
installed?
Extended memory
1) Installation of driver software, setting,
and operation check
Yes
Install scanner/document feeder.
* AR-EF1 /AR-RK1
AR-D13/AR-D14/
AR-DU3/AR-DU4
End
When installing a paper feeding device, an optional power supply unit or a duplex/bypass device, be
sure to re-attach the rear cabinet, the AC inlet cover, and the harness cover of the main unit at the
end of installation as needed.
When installing a controller board, a facsimile unit, and other electric devices, be sure to install them
one at a time.
Only off center adjustment is needed for AR-DU3.
When installing an option, refer to the Service Manual for that option and or the AR-M350 / M450 Service Manual.
AR-M350U UNPACKING AND INSTALLATION 6-1
( "
#$%&'
2. AR-P14 installing procedure
<Before installation>
*
*
*
This installation procedure is provided for use with the AR-M350U/
M450U series.
To connect this machine to a network, a Print Server Card (NIC) ARNC5J must be installed to the multi-function controller board in
advance.
<3>Remove the control PWB unit.
Remove the five screws that fix the control PWB unit to the main unit of
the printer.
Then, hold the two grips and pull out the control PWB unit to remove it
from the main unit.
To enable the printer expansion function, the product key must be
acquired.
The application number, machine serial number, and product key
number are important information.
Keep the above information for future reference.
1) Mount the printer expantion kit ROMs to the control PWB.
<1>Turn off the main switch of the main unit of the printer
Turn the main switch located on the front side of the main unit to the
"OFF" position.
If the machine is equipped with a facsimile unit, also turn off the FAX
power switch.
Then remove the power plug from the outlet.
.
<2>Remove the cables connected to the control PWB unit.
Remove all the cables connected to the control PWB unit of the main unit
of the printer.
<4>Mount the printer expansion kit ROMs(2 pcs.)to the control PWB.
Remove the ROMs(main and boot ROMs)from the control PWB and
replace them with the two ROMs(main and boot ROMs)of the printer
expansion kit.
The main and boot ROMs are indicated with "MAIN" and "BOOT" on the
labels on the ROMs respectively.
When mounting the printer expansion kit ROMs, insert them to the same
positions in the same direction as those before replacement and ensure
that the inserted printer expansion kit ROMs are locked with the fittings
of the sockets.
<5>Re-attach the control PWB.
Attach the control PWB to the main unit of the printer and fix it using five
screws.
AR-M350U UNPACKING AND INSTALLATION 6-2
) "
#$%&'
<6>Connect the cables to the control PWB.
Connect all the cables that have been removed in <2> to the original
positions of the control PWB unit.
3) Prepare to enable the printer expansion function.
To enable the printer expansion function, use the keys on the operation
panel to enter the product key.
For entry of the product key, see the key operator's guide of the operation
manual for the main unit.
Carry out the network setting for the Print Server Card.
Use a key operator program to carry out the network setting for this
machine. For this network setting, the customer's network environment
must be checked. Consult the network administrator to carry out the
setting.
If another peripheral device must be installed, carry out the
following steps at the end of the installation work.
2) Turn on the main switch of the main unit of the printer.
Insert the power plug of the main unit of the printer to the outlet.
Then, turn the main switch located on the front side of the main unit to
the "ON" position.
If the machine is equipped with a facsimile unit, turn on the FAX power
switch.
In addition to the network setting for this machine, to use the
machine in the network environment:
According to the customer's network environment, install the driver
software from the CD-ROM supplied with this machine and use the utility
software supplied with the Print Server Card to set the network printer for
the server computer.
For installation in the server computer and network setting, see the
operation manual supplied with the main unit.
This setting must be carried out by the network administrator or based on
consultation with the network administrator.
4) To check the operation of the printer expansion function.
When the network settings and the driver settings are complete, perform
a test print to check if printing can be performed successfully.
(When test printing is completed successfully, use the "list print" key
operator program to print the network settings and keep the printout for
future reference.)
Installation of AR-P14 is now complete.
AR-M350U UNPACKING AND INSTALLATION 6-3
!
[7] MAINTENANCE
1. Self print of set values
Use SIM 22-6 to print the set values (machine settings) and jam history.
These values must be printed before execution of maintenance or disassembly procedures.
2. Maintenance System Table
The maintenance system table is the same as that of the AR-M350/M450.
A. Scanner / DSPF
Maintenance cycle : 50K
Check (Clean, replace, or adjust as necessary.)
Unit name
Clean
Replace
Adjust
Lubricate
Move position
When
50K 100K 150K 200K 250K 300K 350K 400K
calling
Part name
Remark
Optical section Mirror/Lens/Reflector/Sensors
Table glass/OC
White reference glass
Rails
Drive belt/Drive wire/Pulley
DSPF
Paper feed section
Transport section
Take-up roller
Note 2
Separation pad
Note 2
Paper feed roller
Note 2
PS roller
Exposure section
(Dust-proof glass)
Paper exit section
Paper feed roller SPF
Other
Sensors
Finish stamp section
[Option]
(Japan only)
Stamp solenoid
For cleaning, blow air.
Stamp individual part
Note 2: Replacement reference: Same as above or 2 years.
AR-M350U MAINTENANCE 7-1
User replacement
at 10K or 1 year.
" !
B. Engine section
*
For disassembly procedures, refer to the AR-P350/P450 Service Manual.
Maintenance cycle : 50K
Check (Clean, replace, or adjust as necessary.)
Unit name
Drum peripheral
Clean
When
calling
Part name
Replace
Adjust
Lubricate
50K 100K 150K 200K 250K 300K 350K 400K
Drum
Move position
Remark
Installed when shipping
Cleaner blade
Toner reception seal
Side molt
Transfer roller
Discharge plate
TR bearing (F/R)
Transfer roller collar
After-transfer star ring
TR gear
Screen grid
(
)
(
)
Drum separation pawl UN
Charger case (M/C)
Charging plate
(saw teeth)
Developing section
Developer
Supplied when installing
DV blade
DSD collar
DV side seal F
DV side seal R
Toner cartridge
Fusing section
Attached when installing./
EX Japan: 814g,
user replacement for every 27K.
Upper heat roller
Lower heat roller
Upper separation pawl
Lower separation pawl
Thermistor
Clean and remove paper dust.
Upper heat roller gear
Paper guides
Gears
Cleaning roller
CL roller collar
Filters
Paper feed section
Ozone filter
Paper feed roller
Note 1
Torque limiter
Note 1
Transport section
PS follower roller
Paper exit reverse section Transport rollers
Transport paper guides
Paper dust remover
Drive section
Specified position
Belts
Image quality
Other
Sensors
Note 1:Replacement reference: Use the counter value of each paper feed port as the replacement reference.
Paper feed roller/Torque limiter section: 80K or 2 years
AR-M350U MAINTENANCE 7-2
# !
C. Peripheral devices
Maintenance cycle : 50K
Check (Clean, replace, or adjust as necessary.)
Clean
Option name
When
calling
ADU
+ Manual feed
Part name
Paper feed
Paper feed
separation section rollers
Transport section
(
Replace
Adjust
Lubricate
50K 100K 150K 200K 250K 300K 350K 400K
)
Move position
Remark
Note 3
Separation pad
(
)
Note 3
Torque limiter
(
)
Note 3
Transport rollers
Transport paper
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Desk
Paper feed
Paper feed
(Multi stage LCC) separation section rollers
Multi purpose
Torque limiter
Transport section
(
)
(
)
Note 3
Note 3
Transport roller
Transport paper
guides
Drive section
Gears
(Specified position)
Belts
Finisher
Other
Sensors
Transport section
Transport rollers
De-curler roller
(
)
Transport paper
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Discharge brush
Mail-bin
stacker
Staple un
Replace UN
at 100K staple.
Staple cartridge
User replacement
for every 3000pcs.
Transport section
Transport roller
Transport paper
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Transport section
Transport roller
Discharge brush
Saddle finisher
Transport paper
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Discharge brush
Staple UN
Replace UN at 100K staple
(including the staple UN
and the holder section).
Staple cartridge
User replacement
for every 5000 pcs.
Note 3: Replacement reference: Use the counter value of each paper feed port as the replacement reference.
Paper feed roller/Separation pad/Torque limiter section: 80K or 2 years
AR-M350U MAINTENANCE 7-3
!"#$
[8] SIMULATION
<List of machine model codes>
Item
For the simulation, the following items have been changed.
MACHINE
22-10
Purpose
Function (Content)
Display
Content
AR-P350/350LP
AR-P450/450LP
Adjustment, setup, operation data output, check
(display)
Used to check the system configuration
(option, internal hardware).
AR-M350/350M (Include the N model)
AR-M450/450M (Include the N model)
AR-310M
AR-M350U
Section
Item
Spec
Operation/Procedure The machine composition below is displayed.
AR-M450U
AR-310S/310F
AR-350S/350F
SIMULATION 22-10
SYSTEM INFORMATION.
MACHINE: *******
SPF: ******* XXXXXXXXXXX
FINISHER : *******
MAIL BIN : *******
PUNCH : ******
DESK/LCC : *******
ADU: ******* XXXXXXXXXXXX
PROCESS TYPE : *
SYSTEM MEMORY: **MB
HDD: ***MB ICU F ******
NIC : ******* NSCN : ******
PS3 : ******
FAX: ******* FAX MEMORY : **MB
HAND SET: *******
STAMP : *******
AR-450S/450F
SPF
AR-EF2
AR-EF1
FINISHER
AR-FN6
AR-FN7
MAIL BIN
<List of display value>
MACHINE
SPF
FINISHER
MAIL BIN
PUNCH
DESK/LCC
ADU
PROCESS TYPE
SYSTEM MEMORY
HDD
ICU
NIC
NSCN
PS3
FAX
FAX MEMORY
HAND SET
STAMP
AR-MS1
Model codes
NONE/ (Model code)
NONE/ (Model code)
NONE/ (Model code)
NONE/ (Model code)
NONE/ (Model code)
NONE/ (Model code)
Process control spec
(1, 2: AR machine 3: DM machine)
Memory capacity (MB)
Hard disk capacity (MB)
PRINTER/MFP
NONE/ (Model code)
NONE/ (Network scanner)
NONE/ (PS3 expansion kit)
NONE/ (Model code)
FAX expansion memory capacity (MB)
NONE/ (Model code)
Finisher stamp NONE/ (Model code)
Punch unit
-
NIC
FAX
Expansion
memory
Punch unit 4 holes
-
Duplex module installed
AR-DU4
Duplex module +
manual feed unit installed
-
Multi-purpose tray installed
AR-D14/D15
Paper feed desk installed
AR-D13
Tandem desk installed
PRINTER
Printer board
AR-M11
MFP board
AR-M12 *
MFP board (U model)
AR-M13 *
MFP board (S model)
0MB
No expansion memory
***MB
Expansion memory ***MB
0MB
Hard disk not installed
****MB
Hard disk installed (AR-HD3)
-
NIC installed
PS3 expansion kit not installed
PS3 expansion kit installed
-
FAX expansion kit installed
AR-NS2F
-
-
Not registered as a product.
AR-M350U SIMULATIONS 8-1
NIC not installed
AR-PK1
AR-SU1
*:
Paper feed desk not installed
AR-MU1
AR-HN5
Finish stamp
Punch unit 4 holes wide hole
Duplex module not installed
AR-DU3
AR-MM9
Handset
Mail bin installed
Punch unit not installed
Punch unit 3 holes
AR-FX5
Network
scanner
Console finisher installed
Mail bin not installed
AR-PN1C
AR-NC5J
PS3
expansion kit
Built-in finisher installed
Punch unit 2 holes
DESK
HD
Duplex document feed unit installed
After-work unit not installed
AR-PN1B
ADU
MEMORY
Document feed unit (SPF) installed
AR-PN1A
AR-PN1D
ICU
Document feed unit not installed
FAX expansion kit not installed
Network expansion kit not installed
Network expansion kit installed
Expansion memory for FAX not
installed
Expansion memory for FAX 8MB
(AR-MM9) installed
handset not installed
Handset installed
Finish stamp unit not installed
Finish stamp unit installed
!"#!$
[9] CIRCUIT DIAGRAM
1. MFP Control PWB(for AR-M350U/M450U)
A.Block Diagrams
General
MEMD[31:0]
SRAM
(256KB)
LA[22:2]
MAA[12:0]
SDRAM
SDRAM DIMM
64MByte
64/128/
(128Mbit x 4)
256MB
Address
Buffer
I/O G/A
(ASIC1)
IEEE1284
I/F
IOA[15:1]
EEPROM
(64Kbit)
SYSTEM Controller
LVX161284
LDATA[15:0]
RTC
DS14C238
MD[63:0]
FAX I/F
Buffer
SysAD[54:33]
Flash
Mask DIMM
DIMM
(32MB)
(8MB)
PS Kanji
Slot1,2,3
RIC I/F
Address Buffer
Gate
SysAD[31:0]
ICU ASIC
HDD PWB
(IDE)
JCI-NIC
no support for
STD control PWB J
AR-M350U CIRCUIT DIAGRAM 9-1
PM2500
PCI Bus
Scanner I/F
LCD
Controller
IOD[7:0]
Engine I/F
Data
Gate
TD62503F
Dracula
SDRAM
(24MB)
SysCMD[8:0]
CPU
TMPR4955AF-200
% !"#!$
CPU Block
Regulator
IC2
1.5V(Core)
5V
Engine I/F
CN13
3.3V(I/O)
Clock buffer
IC9
OSC
X3
66.666Mhz
TDI, TMS, TDO ,TCK, TRST*
CPU
TMPR4955AF
200Mhz
IC20
160pin-QFP
JTAG
CN10
5V
COLDRST
CPURST
3_EXTRQST
PONRST
NMI, INT0*
Reset IC
PST598DN
IC47
3.3V
System
Controller
IC19
Reset IC
PST598IN
IC48
SysCMD[8:0], SysAD[31:0]
SysAD[54:33]
Address
Buffer
IC12, 21
LCX16245
IC16, 24
I/O G/A
IC32
Mask DIMM
CN7
MEMD[31:0]
VCC_B
SRAM
IC55,56
Address
Buffer
IC49, 50
IC51, 52
AR-M350U CIRCUIT DIAGRAM 9-2
Flash DIMM
CN4,5,6
FAX I/F (CN16)
INT1*,INT2*,INT3*
LA[22:2]
& !"#!$
ROM Block ( Flash & Mask )
3.3V
SysAD[54:32]
VCCW
Address
Buffer
IC12, 21
LA[22:2]
GND
SysAD[31:0]
LCX16245
IC16, 24
MEMD[31:0]
DIMM Slot
CN4:8MB-Flash
CN5:8MB-Flash
CN6:8MB-Flash
ROMBUFOE*
ROMBUFDIR*
FMCS8:CN4
System
Controller
IC19
456pinBGA
CODECS0*
CODECS1*
CODECS2*
CODECS3*
FONTCS0*
FONTCS1*
FONTCS2*
FONTCS3*
FONTCS4*
FONTCS5*
FONTCS6*
FONTCS7*
FMCS10:CN5
FMCS12:CN6
I/O G/A
IC32
240pinQFP
AR-M350U CIRCUIT DIAGRAM 9-3
' !"#!$
SDRAM Block ( Standard & Option )
OSC
X3
66.666Mhz
DRCLK
MEMCLK0
Clock
buffer
IC9
MAA[12:0]
MD[63:0]
SDRAM
SDQMA[7:0]
MWE
MCS0
MRASA
MCASA
BSEL0A,1A
CKEA
System
Controller
IC4, 5,6,7
128Mbit x 4
IC19
456pinBGA
MEMCLK1,2,3,4
MWE
MCS1A,2A
MRASA
MCASA
BSEL0A,1A
CKEA
DIMM Slot
CN3
(64,128,256MB)
SDA,SCL
AR-M350U CIRCUIT DIAGRAM 9-4
( !"#!$
PCI Block ( ICU & Option )
PCI-Bus
System
Controller
IC19
456pin-BGA
SDRAM
IC22, IC27
24MB
Scanner I/F
LVDS
IC18
CN8
ICU ASIC
IC13
160pin-QFP
OSC
X1
66.66Mhz
Selector
IC14
OSC
X5
68.5Mhz
Engine I/F
CN13
OSC
X2
40.57Mhz
Buffer
IC8
IC25
304pin-QFP
PM2500
OSC
X4
31.55.Mhz
JCI-NIC
(100Base-T)
CN2
no support for
STD control PWB J
CN12
AR-M350U CIRCUIT DIAGRAM 9-5
HDD-PWB
(2.5inch HDD)
) !"#!$
I/O Block ( EEPROM & Misc I/O )
LVX161284
IC15
IEEE1284 I/F
System
Controller
IC19
456pin-BGA
DS14C238
IC42
RIC I/F (RS232C)
IOA[15:1]
LDATA[15:0]
CN1
CN14
16373
IC34
I/O G/A
CN13
Scanner I/F
CN8
LCD
Controller
IC53
JP4,5
TD62503F
IC38
245
IC31
IC32
240pin-QFP
TD62503F
IC41
IOD[7:0]
Engine I/F
OSC
X7
14.7456Mhz
RTC
NJU6356
IC40
Xtal
32.768khz
IOA[15:1]
IOD[7:0]
EEPROM
IC36
64Kbit
AR-M350U CIRCUIT DIAGRAM 9-6
Switcher
VCC_B
5V
Battery
* !"#!$
AR-M350U CIRCUIT DIAGRAM 9-7
+ !"#!$
B. Circuit Diagram
5
4
3
[DRAGON-D10][CPU TX4955]
+ C125
D
3.3V
10uF/16V
R127
R126
10
10
C130
C129
0.1uF
1000pF
BR26
SYSADC2
SYSADC3
SYSADC0
SYSADC1
8
7
6
5
1
2
3
4
R136
R137
10
10
SYSADC[3:0]
SYSADC3
SYSADC0
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
3.3V
C
R123
R122
10K
4.7K
3
3
3
3
JTDO_A
JTDI
JTCLK
JTMS
A_SYSAD4
A_SYSAD5
A_SYSAD6
A_SYSAD7
A_SYSAD8
A_SYSAD9
A_SYSAD10
A_SYSAD11
A_SYSAD12
B
A_SYSAD13
A_SYSAD14
VSS
BUFSEL1
JTDO
JTDI
JTCK
JTMS
VCCIO
VSS
SYSAD4
SYSAD5
VCCINT
VSS
SYSAD6
VCCIO
VSS
SYSAD7
SYSAD8
VCCINT
VSS
SYSAD9
VCCIO
VSS
SYSAD10
SYSAD11
VCCINT
VSS
SYSAD12
VCCIO
VSS
SYSAD13
SYSAD14
VCCINT
VSS
SYSAD15
BUFSEL0
PCST3
PCST2
PCST1
PCST0
VCCIO
IC20
TMPR4955AF-200
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
A_SYSAD15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
VCCIO
MASTERCLOCK
VSS
VCCPLL
PLLCAP
VSSPLL
VCCIO
VSS
VCCIO
PCST4
PCST5
PCST6
PCST7
PCST8
SYSAD3
VSS
VCCINT
SYSAD2
SYSAD1
VSS
VCCIO
SYSAD0
SYSADC1/(GND)
VSS
VCCINT
SYSADC0/(GND)
VSS
VCCIO
SYSADC3/(GND)
VSS
VCCINT
SYSADC2/(GND)
Y AD31
3.3V
SYSADC2
A SYSAD31
3.3V
A_SYSAD2
A_SYSAD1
A_SYSAD3
CPUCLK
VSS
TRST*
RDRDY*/(GND)
WRRDY*/(EOK*)
VALIDIN*/(EVALID*)
VALIDOUT*/(PVALID*)
RELEASE*/(PMASTER*)
VCCIO
PLLRESET*
VCCINT
TINTDIS
VSS
SYSCMD0
SYSCMD1
SYSCMD2
SYSCMD3
SYSCMD4
SYSCMD5/(GND)
VCCIO
VSS
SYSCMD6/(GND)
SYSCMD7/(GND)
SYSCMD8/(GND)
SYSCMDP/(GND)
VCCINT
VSS
VCCIO
HALT/DOZE
INT0*
INT1*
INT2*
INT3*
INT4*
21
A_SYSAD0
SYSADC1
4 A_SYSAD[31:0]
10K
3
2
JTRST
RDY
2
2
2
2
3_VALIDIN
3_VALIDOUT
3_RELEASE
VCCOK
R118
R116
10
10
A_SYSCMD0
A_SYSCMD1
A_SYSCMD2
A_SYSCMD3
A_SYSCMD4
A_SYSCMD5
R112
A
4 A_SYSCMD[8:0]
R119
3.3K
5
4
AR-M350U CIRCUIT DIAGRAM 9-8
3
A_SYSCMD6
A_SYSCMD7
A_SYSCMD8
3.3V
R100
4.7K
D15
EL0
3
2
1
0
O
VCCIO
MASTERCLOCK
VSS
VCCPLL
PLLCAP
VSSPLL
VCCIO
VSS
VCCIO
PCST4
PCST5
PCST6
PCST7
PCST8
SYSAD3
VSS
VCCINT
SYSAD2
SYSAD1
VSS
VCCIO
SYSAD0
SYSADC1/(GND)
VSS
VCCINT
SYSADC0/(GND)
VSS
VCCIO
SYSADC3/(GND)
VSS
VCCINT
SYSADC2/(GND)
SYSAD31
VSS
VCCIO
SYSAD30
VSS
VCCINT
SYSAD29
SYSAD28
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
D6
O
D7
D8
NT
3
D12
O
D13
D14
NT
O
D4
D5
NT
IC20
D9
O
TMPR4955AF-200
A_SYSAD29
A_SYSAD28
A_SYSAD30
SYSADC2
A_SYSAD31
SYSADC3
SYSADC0
A_SYSAD0
SYSADC1
A_SYSAD2
A_SYSAD1
A_SYSAD3
A_SYSCMD6
A_SYSCMD7
A_SYSCMD8
D10
D11
NT
VSS
TRST*
RDRDY*/(GND)
WRRDY*/(EOK*)
VALIDIN*/(EVALID*)
VALIDOUT*/(PVALID*)
RELEASE*/(PMASTER*)
VCCIO
PLLRESET*
VCCINT
TINTDIS
VSS
SYSCMD0
SYSCMD1
SYSCMD2
SYSCMD3
SYSCMD4
SYSCMD5/(GND)
VCCIO
VSS
SYSCMD6/(GND)
SYSCMD7/(GND)
SYSCMD8/(GND)
SYSCMDP/(GND)
VCCINT
VSS
VCCIO
HALT/DOZE
INT0*
INT1*
INT2*
INT3*
INT4*
INT5*
VCCIO
VSS
TPC3
TPC2
TPC1
DCLK
EL1
A_SYSCMD0
A_SYSCMD1
A_SYSCMD2
A_SYSCMD3
A_SYSCMD4
A_SYSCMD5
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
!"#!$
3
2
VSS
DIVMODE0
DIVMODE1
MODE43*
VCCIO
SYSAD27
SYSAD26
VSS
VCCINT
SYSAD25
VSS
VCCIO
SYSAD24
SYSAD23
VSS
VCCINT
SYSAD22
VSS
VCCIO
SYSAD21
SYSAD20
VSS
VCCINT
SYSAD19
VSS
VCCIO
SYSAD18
SYSAD17
VSS
VCCINT
SYSAD16
VSS
VCCIO
ENDIAN
VCCIO
COLDRESET*
RESET*
EXTRQST*/(EREQ*)
NMI*
VCCINT
1
26
3.3V
37
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
R100
4.7K
2
AR-M350U CIRCUIT DIAGRAM 9-9
1.5V
0.1uF
C89
0.1uF
C92
0.1uF
C82
0.1uF
C107
0.1uF
C110
0.1uF
C78
0.1uF
C108
0.1uF
C102
0.1uF
C121
0.1uF
C122
0.1uF
C72
0.1uF
C73
0.1uF
C71
0.1uF
C70
3.3V
A_SYSAD25
A_SYSAD21
A_SYSAD20
A_SYSAD18
A_SYSAD17
A2_INT
TDPOF
INT2
INT1
INT0
DRINT
R76
R74
4.7K
4.7K
A_SYSAD16
10K
COLDRST
CPURST
3_EXTRQST
NMI_DR
3.3V
R86
10K
11
10,22
10
10
10
2
1
2,7,9
2,10,11,17,18
2
2
D
1.5V
3.3V
C
A_SYSAD27
A_SYSAD26
R75
0
NO ASM
A_SYSAD24
A_SYSAD23
A_SYSAD22
A_SYSAD19
3.3V
R73
B
!"#!$
A
B
C
[Print Controller (for AR-M350U / M450U) (1/3)]
5
4 SYSCMD[8:0]
IC19A
CKE
SYSCMD8
SYSCMD7
SYSCMD6
SYSCMD5
SYSCMD4
SYSCMD3
SYSCMD2
SYSCMD1
SYSCMD0
AA1
AA2
AA3
Y4
AB1
AB2
Y5
AA5
AA4
Y3
W4
Y2
V5
W3
Y1
W2
V4
W1
V3
V2
V1
U4
U3
T5
U2
U1
T4
T3
T2
R5
R4
T1
R3
R2
P4
R1
P3
P2
P1
N1
N2
N3
M1
N4
M2
M3
L1
M4
L2
L3
L4
K1
K2
L5
K3
K4
J1
J2
J3
H1
J4
H2
G1
J5
H3
H4
G2
G3
F1
F2
G4
F3
E1
6 SYSAD[54:33]
4
4,6
SYSAD54
SYSAD53
SYSAD52
SYSAD51
SYSAD50
SYSAD49
SYSAD48
SYSAD47
SYSAD46
SYSAD45
SYSAD44
SYSAD43
SYSAD42
SYSAD41
SYSAD40
SYSAD39
SYSAD38
SYSAD37
SYSAD36
SYSAD35
SYSAD34
SYSAD33
SYSAD[31:0]
SYSAD31
SYSAD30
SYSAD29
SYSAD28
SYSAD27
SYSAD26
SYSAD25
SYSAD24
SYSAD23
SYSAD22
SYSAD21
SYSAD20
SYSAD19
SYSAD18
SYSAD17
SYSAD16
SYSAD15
SYSAD14
SYSAD13
SYSAD12
SYSAD11
SYSAD10
SYSAD9
SYSAD8
SYSAD7
SYSAD6
SYSAD5
SYSAD4
SYSAD3
SYSAD2
SYSAD1
SYSAD0
3
2
1
1
3_VALIDOUT
3_RELEASE
AB3
AC2
AC3
AB4
AD3
BR16
1
1
1
1
1
2
3
4
3_VALIDIN
RDY
3_EXTRQST
DRINT
8
7
6
5
AC4
AD4
AC5
AD5
AE4
AB7
BR6
1
2
3
4
1
NMI_DR
1
VCCOK
1,10,11,17,18 CPURST
1,7,9 COLDRST
3,10,11,12,22 PONRST
21
DRCLK
8
7
6
5
D4
AC6
5
SYSCMD8
SYSCMD7
SYSCMD6
SYSCMD5
SYSCMD4
SYSCMD3
SYSCMD2
SYSCMD1
SYSCMD0
SYSAD63
SYSAD62
SYSAD61
SYSAD60
SYSAD59
SYSAD58
SYSAD57
SYSAD56
SYSAD55
SYSAD54
SYSAD53
SYSAD52
SYSAD51
SYSAD50
SYSAD49
SYSAD48
SYSAD47
SYSAD46
SYSAD45
SYSAD44
SYSAD43
SYSAD42
SYSAD41
SYSAD40
SYSAD39
SYSAD38
SYSAD37
SYSAD36
SYSAD35
SYSAD34
SYSAD33
SYSAD32
SYSAD31
SYSAD30
SYSAD29
SYSAD28
SYSAD27
SYSAD26
SYSAD25
SYSAD24
SYSAD23
SYSAD22
SYSAD21
SYSAD20
SYSAD19
SYSAD18
SYSAD17
SYSAD16
SYSAD15
SYSAD14
SYSAD13
SYSAD12
SYSAD11
SYSAD10
SYSAD9
SYSAD8
SYSAD7
SYSAD6
SYSAD5
SYSAD4
SYSAD3
SYSAD2
SYSAD1
SYSAD0
VALIDIN_
VALIDOUT_
READY_
EXTRQST_
RELEASE_
INTR_
NMI_
VCCOK
CPURST_
COLDRST_
POR_
MASTERCLK
SYSBUS64EN
MRAS_
MCAS_
MWE_
BSEL1
BSEL0
MCS_4
MCS_3
MCS_2
MCS_1
MCS_0
MAD12
MAD11
MAD10
MAD9
MAD8
MAD7
MAD6
MAD5
MAD4
MAD3
MAD2
MAD1
MAD0
MD63
MD62
MD61
MD60
MD59
MD58
MD57
MD56
MD55
MD54
MD53
MD52
MD51
MD50
MD49
MD48
MD47
MD46
MD45
MD44
MD43
MD42
MD41
MD40
MD39
MD38
MD37
MD36
MD35
MD34
MD33
MD32
MD31
MD30
MD29
MD28
MD27
MD26
MD25
MD24
MD23
MD22
MD21
MD20
MD19
MD18
MD17
MD16
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
DQM7
DQM6
DQM5
DQM4
DQM3
DQM2
DQM1
DQM0
AB11
AC12
AF11
AD12
AC13
AE12
AE11
AD11
AC11
AF10
AE10
AE16
AB15
AC15
AF16
AD15
AE15
AF15
AD14
AE14
AF14
AF13
AE13
AD13
M26
N24
N25
N26
P26
P25
P24
R26
P23
R25
R24
T26
R23
T25
T24
T23
U26
U25
T22
U24
U23
V26
V24
W26
V23
W25
Y26
V22
W24
W23
Y24
AA26
AA25
Y23
AA24
AB26
AB25
AA22
Y22
AB24
AC25
AB23
AC24
AC23
AD24
AC22
AD23
AD22
AC21
AB21
AB20
AE22
AF22
AC20
AD21
AF21
AD20
AC19
AE20
AB18
AD19
AF20
AE19
AD18
MD63
MD62
MD61
MD60
MD59
MD58
MD57
MD56
MD55
MD54
MD53
MD52
MD51
MD50
MD49
MD48
MD47
MD46
MD45
MD44
MD43
MD42
MD41
MD40
MD39
MD38
MD37
MD36
MD35
MD34
MD33
MD32
MD31
MD30
MD29
MD28
MD27
MD26
MD25
MD24
MD23
MD22
MD21
MD20
MD19
MD18
MD17
MD16
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
AE18
AF18
AC17
AD17
AB16
AE17
AF17
AD16
SDQMA[7:0]
KS5M0U1347CBP
1
BR10
SDQMA0
SDQMA1
SDQMA2
SDQMA3
1
2
3
4
SDQMA4
SDQMA5
SDQMA6
SDQMA7
1
2
3
4
8
7
6
5
BR20
A
8
7
6
5
B
AR-M350U CIRCUIT DIAGRAM 9-10
C
C
!"#!$
D
E
BR18
8
7
6
5
1
2
3
4
R64
R65
BR7
8
7
6
5
10
10
1
2
3
4
MAA12
1
2
3
4
MAA11
MAA10
MAA9
MAA8
1
2
3
4
MAA7
MAA6
MAA5
MAA4
1
2
3
4
MAA3
MAA2
MAA1
MAA0
CKEA
MRASA
MCASA
MWE
5
5
5
5
BSEL1A
BSEL0A
5
5
MCS2A
MCS1A
MCS0
5
5
5
MAA[12:0]
5
5
BR19
CKE
MRAS_
MCAS_
MWE_
BSEL1
BSEL0
MCS_4
MCS_3
MCS_2
MCS_1
MCS_0
MAD12
MAD11
MAD10
MAD9
MAD8
MAD7
MAD6
MAD5
MAD4
MAD3
MAD2
MAD1
MAD0
MD63
MD62
MD61
MD60
MD59
MD58
MD57
MD56
MD55
MD54
MD53
MD52
MD51
MD50
MD49
MD48
MD47
MD46
MD45
MD44
MD43
MD42
MD41
MD40
MD39
MD38
MD37
MD36
MD35
MD34
MD33
MD32
MD31
MD30
MD29
MD28
MD27
MD26
MD25
MD24
MD23
MD22
MD21
MD20
MD19
MD18
MD17
MD16
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
DQM7
DQM6
DQM5
DQM4
DQM3
DQM2
DQM1
DQM0
AB11
8
7
6
5
AC12
AF11
AD12
AC13
AE12
BR9
8
7
6
5
AE11
AD11
AC11
AF10
AE10
BR8
8
7
6
5
AE16
AB15
AC15
AF16
AD15
AE15
AF15
AD14
AE14
AF14
AF13
AE13
AD13
M26
N24
N25
N26
P26
P25
P24
R26
P23
R25
R24
T26
R23
T25
T24
T23
U26
U25
T22
U24
U23
V26
V24
W26
V23
W25
Y26
V22
W24
W23
Y24
AA26
AA25
Y23
AA24
AB26
AB25
AA22
Y22
AB24
AC25
AB23
AC24
AC23
AD24
AC22
AD23
AD22
AC21
AB21
AB20
AE22
AF22
AC20
AD21
AF21
AD20
AC19
AE20
AB18
AD19
AF20
AE19
AD18
3_MD[63:0]
5
BR41
5
6
7
8
4
3
2
1
3_MD63
3_MD62
3_MD61
3_MD60
4
3
2
1
3_MD59
3_MD58
3_MD57
3_MD56
4
3
2
1
3_MD55
3_MD54
3_MD53
3_MD52
4
3
2
1
3_MD51
3_MD50
3_MD49
3_MD48
4
3
2
1
3_MD47
3_MD46
3_MD45
3_MD44
4
3
2
1
3_MD43
3_MD42
3_MD41
3_MD40
4
3
2
1
3_MD39
3_MD38
3_MD37
3_MD36
4
3
2
1
3_MD35
3_MD34
3_MD33
3_MD32
4
3
2
1
3_MD31
3_MD30
3_MD29
3_MD28
4
3
2
1
3_MD27
3_MD26
3_MD25
3_MD24
4
3
2
1
3_MD23
3_MD22
3_MD21
3_MD20
4
3
2
1
3_MD19
3_MD18
3_MD17
3_MD16
4
3
2
1
3_MD15
3_MD14
3_MD13
3_MD12
4
3
2
1
3_MD11
3_MD10
3_MD9
3_MD8
4
3
2
1
3_MD7
3_MD6
3_MD5
3_MD4
4
3
2
1
3_MD3
3_MD2
3_MD1
3_MD0
4
BR39
5
6
7
8
MD63
MD62
MD61
MD60
MD59
MD58
MD57
MD56
MD55
MD54
MD53
MD52
MD51
MD50
MD49
MD48
MD47
MD46
MD45
MD44
MD43
MD42
MD41
MD40
MD39
MD38
MD37
MD36
MD35
MD34
MD33
MD32
MD31
MD30
MD29
MD28
MD27
MD26
MD25
MD24
MD23
MD22
MD21
MD20
MD19
MD18
MD17
MD16
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
BR40
5
6
7
8
BR33
5
6
7
8
BR34
5
6
7
8
3
BR28
5
6
7
8
BR29
5
6
7
8
BR25
5
6
7
8
BR24
5
6
7
8
BR15
5
6
7
8
2
BR23
5
6
7
8
BR13
5
6
7
8
BR12
5
6
7
8
AE18
AF18
AC17
AD17
AB16
AE17
AF17
AD16
BR22
5
6
7
8
BR21
5
6
7
8
1
BR11
5
6
7
8
C
D
AR-M350U CIRCUIT DIAGRAM 9-11
E
% !"#!$
A
B
C
[Print Controller (for AR-M350U / M450U) (2/3)]
3.3V
IC19B
C54
C106
22uF/16V
22uF/16V
+
C100
0.1uF
C64
+
0.1uF
C57
2.5V
E14
N5
P22
AB13
4
C96
0.1uF
C53
0.1uF
C88
0.1uF
C128
22uF/16V
+
22uF/16V
+
0.1uF
CVDD
CVDD
CVDD
CVDD
C114
C115
3
2
A1
A2
A3
A4
A8
A12
A23
A24
A25
A26
B1
B2
B3
B24
B25
B26
C1
C2
C25
C26
D1
D11
D26
E8
E15
E19
H5
H22
L11
L12
L13
L14
L15
L16
M5
M11
M12
M13
M14
M15
M16
N11
N12
N13
N14
N15
N16
P11
P12
P13
P14
P15
P16
R11
R12
R13
R14
R15
R16
R22
T11
T12
T13
T14
T15
T16
V25
W5
W22
Y25
AA23
AB8
AB12
AB19
AC1
AC14
AC16
AC26
AD1
AD2
AD25
AD26
AE1
AE2
AE3
AE21
AE23
AE24
AE25
AE26
AF1
AF2
AF3
AF4
AF12
AF19
AF23
AF24
AF25
AF26
BR42
10
10
DREQ0
DREQ3
10
DACK3
10
DACK0
4
3
2
1
5
6
7
8
BR46
10
1
2
3
4
STC0
10
8
7
6
5
SIOCLK
3.3V
BR45
4
3
2
1
3.3V
5
6
7
8
ROMCLK
R135
4.7K
NO ASM
5
5
SCL
SDA
3.3V
10K
0.1uF
C85
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
3.3V
IC28
1
2
3
4
A0
VCC
A1
WP
A2
SCL
VSS
SDA
8
NO ASM
0.1uF
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
R171
5
E5
E10
E13
E17
E22
K5
K22
N22
P5
U5
U22
AB5
AB10
AB14
AB17
AB22
AC18
7
EEPWP
6
EEPCLK
5
EEPDATA
10
3.3V
R63
3.3V
CAT24WC64K
NO ASM
4.7K
C152
R128
4.7K
R132
4.7K
R133
4.7K
R146
R111
4.7K
4.7K
R150
R110
4.7K
4.7K
R145
R114
75
75
0.1uF
NO ASM
A
C133
C109
0.1uF
0.01uF
NO ASM
A
NO ASM
NO ASM
R144
R115
10K
10K
2,10,11,12,22 PONRST
2.5V
2.5V
C118
C113
C127
C126
0.1uF
0.1uF
0.1uF
0.1uF
KS5M0U1347CBP
3.3V
1K
3.3V
NO ASM
CN10
4
6
8
1
10
2
VCC
NC
NC
FG
GND
TDI
TMS
TDO
TCK
TRST_
9
5
3
1
JTDO
7
9A12-1034
A
B
AR-M350U CIRCUIT DIAGRAM 9-12
C
1K R129
1K R134
1K R130
R151
& !"#!$
C
D
E
IC19D
L26
M24
M25
N23
BR42
4
3
2
1
5
6
7
8
L24
L25
M22
M23
BR46
1
2
3
4
8
7
6
5
L22
K25
K26
L23
B20
C20
B21
3.3V
BOOTCS_
DREQ3_
DREQ2_
DREQ1_
DREQ0_
CODECS3_
CODECS2_
CODECS1_
CODECS0_
DACK3_
DACK2_
DACK1_
DACK0_
FONTCS7_
FONTCS6_
FONTCS5_
FONTCS4_
FONTCS3_
FONTCS2_
FONTCS1_
FONTCS0_
DMA_TC3_
DMA_TC2_
DMA_TC1_
DMA_TC0_
SCLK
ADV_
BUFOE_
BUFDIR
TXD1
RXD1
BR45
4
3
2
1
3.3V
5
6
7
8
A21
D20
D19
C19
ROMOE_
ROMWE_
TXD0
RXD0
TxRDY
RxRDY
ROMCLK
AB6
AF7
AB9
AD8
AC8
AE7
AD7
AF6
AE6
6,10
CODECS2
CODECS1
CODECS0
10
10
10
FONTCS7
FONTCS6
FONTCS5
FONTCS4
FONTCS3
FONTCS2
FONTCS1
FONTCS0
10
10
10
10
10
10
10
12
3.3V
AE8
AC9
AF8
BR17
8
7
6
5
AD9
AE9
AF9
BOOTCS
5
AC7
AD6
AF5
AE5
1
2
3
4
ROMBUFOE
ROMBUFDIR
6
6
ROMOE
ROMWE
8,10,12
6,10,12
R62
R61
10K
10K
ROMCLK
ROMCLK
R135
4.7K
NO ASM
4
E21
A22
EECLK0
EEDAT0
NO ASM
LCS3_
LCS2_
LCS1_
LCS0_
ALE
LWE_
B22
C21
EEPWP
LOE_
EECLK1
EEDAT1
10
WAIT_
3.3V
EEPCLK
BR48
J25
J26
K23
K24
8
7
6
5
J24
1
2
3
4
BR62
H26
1
2
3
4
J23
8
7
6
5
H25
LCS0
LCS1
LCS2
10
10
10
ALE
6
LWE
10
LOE
6,10
WAIT
11
3_LDATA[15:0] 6
EEPDATA
R63
BR58
3.3V
4.7K
R128
4.7K
R132
4.7K
R133
4.7K
R146
R111
4.7K
4.7K
R150
R110
4.7K
4.7K
R145
R114
75
75
AD10
C133
C109
0.1uF
0.01uF
NO ASM
AC10
C18
B18
A18
D17
D23
F5
D22
D2
D21
G5
NO ASM
NO ASM
R144
R115
10K
10K
C22
F4
D3
E2
2.5V
TYPESEL1
TYPESEL0
TESTMODE_
THR_MODE
SCANTEST
SCANEN
VSEL[1]
VSEL[0]
VCOIN[1]
VCOIN[0]
CPOUT[1]
CPOUT[0]
PLL_EN[1]
PLL_EN[0]
PLL_TEST
PLL_RST
2.5V
LDATA15
LDATA14
LDATA13
LDATA12
LDATA11
LDATA10
LDATA9
LDATA8
LDATA7
LDATA6
LDATA5
LDATA4
LDATA3
LDATA2
LDATA1
LDATA0
C118
C113
C127
C126
0.1uF
0.1uF
0.1uF
0.1uF
E4
C23
1
2
3
4
8
7
6
5
3_LDATA15
3_LDATA14
3_LDATA13
3_LDATA12
8
7
6
5
3_LDATA11
3_LDATA10
3_LDATA9
3_LDATA8
8
7
6
5
3_LDATA7
3_LDATA6
3_LDATA5
3_LDATA4
8
7
6
5
3_LDATA3
3_LDATA2
3_LDATA1
3_LDATA0
BR59
1
2
3
4
3
BR60
1
2
3
4
BR61
1
2
3
4
VFCLK
PAGE_
HSYNC_
VDATAEN
VDATA_
E3
B23
E24
F23
F22
G22
E25
E26
G23
F24
F25
F26
G24
H23
G25
J22
H24
G26
3.3V
E20
C24
D25
D24
R121
4.7K
E23
PLL_VDD
PLL_VDD
PLL_GND
PLL_GND
2
JTCLK
JTMS
JTDO
JTRST_
JTDI
A20
B19
A19
E18
D18
JTDO_A
1
KS5M0U1347CBP
3.3V
1K
JTDO
C
1K R129
1K R134
1K R130
R151
JTDI
JTMS
1
1
JTCLK
1
JTRST
1
D
AR-M350U CIRCUIT DIAGRAM 9-13
1
E
' !"#!$
A
B
C
[Print Controller (for AR-M350U / M450U) (3/3)]
IC19C
5
1 A_SYSCMD[8:0]
SYSCMD[8:0]
A_SYSCMD8
R96
10
SYSCMD8
8
7
6
5
SYSCMD3
SYSCMD2
SYSCMD1
SYSCMD0
8
7
6
5
SYSCMD7
SYSCMD6
SYSCMD5
SYSCMD4
2
PCICLKI
PCICLKO
BR44
A_SYSCMD3
A_SYSCMD2
A_SYSCMD1
A_SYSCMD0
1
2
3
4
A_SYSCMD7
A_SYSCMD6
A_SYSCMD5
A_SYSCMD4
1
2
3
4
PCIMODE
PCI_CBE3
PCI_CBE2
PCI_CBE1
PCI_CBE0
BR43
1 A_SYSAD[31:0]
SYSAD[31:0]
2,6
PCIAD31
PCIAD30
PCIAD29
PCIAD28
PCIAD27
PCIAD26
PCIAD25
PCIAD24
PCIAD23
PCIAD22
PCIAD21
PCIAD20
PCIAD19
PCIAD18
PCIAD17
PCIAD16
PCIAD15
PCIAD14
PCIAD13
PCIAD12
PCIAD11
PCIAD10
PCIAD9
PCIAD8
PCIAD7
PCIAD6
PCIAD5
PCIAD4
PCIAD3
PCIAD2
PCIAD1
PCIAD0
BR66
A_SYSAD0
A_SYSAD1
A_SYSAD2
A_SYSAD3
5
6
7
8
A_SYSAD4
A_SYSAD5
A_SYSAD6
A_SYSAD7
5
6
7
8
A_SYSAD8
A_SYSAD9
A_SYSAD10
A_SYSAD11
5
6
7
8
A_SYSAD12
A_SYSAD13
A_SYSAD14
A_SYSAD15
5
6
7
8
A_SYSAD16
A_SYSAD17
A_SYSAD18
A_SYSAD19
5
6
7
8
A_SYSAD20
A_SYSAD21
A_SYSAD22
A_SYSAD23
5
6
7
8
A_SYSAD24
A_SYSAD25
A_SYSAD26
A_SYSAD27
5
6
7
8
A_SYSAD28
A_SYSAD29
A_SYSAD30
A_SYSAD31
5
6
7
8
4
3
2
1
SYSAD0
SYSAD1
SYSAD2
SYSAD3
4
3
2
1
SYSAD4
SYSAD5
SYSAD6
SYSAD7
4
3
2
1
SYSAD8
SYSAD9
SYSAD10
SYSAD11
4
3
2
1
SYSAD12
SYSAD13
SYSAD14
SYSAD15
4
3
2
1
SYSAD16
SYSAD17
SYSAD18
SYSAD19
4
3
2
1
SYSAD20
SYSAD21
SYSAD22
SYSAD23
4
3
2
1
SYSAD24
SYSAD25
SYSAD26
SYSAD27
4
3
2
1
SYSAD28
SYSAD29
SYSAD30
SYSAD31
4
BR65
BR64
BR63
BR38
3
E16
C17
B17
C8
A7
B8
D9
C9
B9
A9
D10
C10
E11
B10
A10
C11
B11
E12
D12
A11
C12
B12
D13
C13
B13
A13
A14
B14
C14
A15
D14
B15
C15
A16
D15
B16
C16
D16
A17
BR37
BR36
BR35
2
PCI_PARITY
PCI_FRAME_
PCI_IRDY_
PCI_TRDY_
PCI_DEVSEL
PCI_STOP_
PCI_PERR_
PCI_SERR_
PCI_LOCK
PCI_GNT3_
PCI_GNT2_
PCI_GNT1_
PCI_REQ3_
PCI_REQ2_
PCI_REQ1_
PCI_IDSEL
PCI_INTO_
PCI_INTI_
KS5M0U1347CBP
1
A
B
AR-M350U CIRCUIT DIAGRAM 9-14
C
E9
B7
D8
C7
A6
B6
C6
D7
A5
E6
E7
B5
B4
C5
D6
C4
D5
C3
( !"#!$
C
D
E
PCLK_D
21
PCLK_DR
21
IC19C
SYSCMD[8:0]
2
5
PCICLKI
PCICLKO
PCIMODE
PCI_CBE3
PCI_CBE2
PCI_CBE1
PCI_CBE0
E16
C17
B17
C8
A7
B8
D9
1 BR68
2
3
4
PCBE03
PCBE02
PCBE01
PCBE00
8
7
6
5
PCBE0[3:0]
17,18
PCIAD[31:0]
SYSAD[31:0]
2,6
PCIAD31
PCIAD30
PCIAD29
PCIAD28
PCIAD27
PCIAD26
PCIAD25
PCIAD24
PCIAD23
PCIAD22
PCIAD21
PCIAD20
PCIAD19
PCIAD18
PCIAD17
PCIAD16
PCIAD15
PCIAD14
PCIAD13
PCIAD12
PCIAD11
PCIAD10
PCIAD9
PCIAD8
PCIAD7
PCIAD6
PCIAD5
PCIAD4
PCIAD3
PCIAD2
PCIAD1
PCIAD0
PCI_PARITY
PCI_FRAME_
PCI_IRDY_
PCI_TRDY_
PCI_DEVSEL
PCI_STOP_
PCI_PERR_
PCI_SERR_
PCI_LOCK
PCI_GNT3_
PCI_GNT2_
PCI_GNT1_
PCI_REQ3_
PCI_REQ2_
PCI_REQ1_
PCI_IDSEL
PCI_INTO_
PCI_INTI_
C9
B9
A9
D10
C10
E11
B10
A10
C11
B11
E12
D12
A11
C12
B12
D13
C13
B13
A13
A14
B14
C14
A15
D14
B15
C15
A16
D15
B16
C16
D16
A17
E9
B7
D8
C7
A6
B6
C6
D7
A5
E6
E7
B5
1 BR53
2
3
4
8
7
6
5
1 BR67
2
3
4
8
7
6
5
R149
8
7
6
5
PCIAD31
PCIAD30
PCIAD29
PCIAD28
1 BR69
2
3
4
8
7
6
5
PCIAD27
PCIAD26
PCIAD25
PCIAD24
1 BR55
2
3
4
8
7
6
5
PCIAD23
PCIAD22
PCIAD21
PCIAD20
1 BR70
2
3
4
8
7
6
5
PCIAD19
PCIAD18
PCIAD17
PCIAD16
1 BR56
2
3
4
8
7
6
5
PCIAD15
PCIAD14
PCIAD13
PCIAD12
1 BR71
2
3
4
8
7
6
5
PCIAD11
PCIAD10
PCIAD9
PCIAD8
1 BR57
2
3
4
8
7
6
5
PCIAD7
PCIAD6
PCIAD5
PCIAD4
1 BR72
2
3
4
8
7
6
5
PCIAD3
PCIAD2
PCIAD1
PCIAD0
17,18
4
3
2
PAR
PFRAME0
PIRDY0
PTRDY0
PDEVSEL0
PSTOP0
PPERR0
PSERR0
PLOCK0
17,18
10,17,18
17,18
17,18
17,18
17,18
17,18
17,18
17
PCIGNT0
10
3.3V
10
1 BR52
2
3
4
B4
C5
D6
1 BR54
2
3
4
8
7
6
5
C4
D5
C3
KS5M0U1347CBP
PCIREQ0
10,17
1
C
D
AR-M350U CIRCUIT DIAGRAM 9-15
E
) !"#!$
A
B
C
[SDRAM]
5
2
MWE
2
2
2
MCS0
MRASA
MCASA
2
2
2
2
3_MD[63:0]
2
SDQMA[7:0]
2
MAA[12:0]
2
2
BSEL0A
BSEL1A
IC4
4
MAA0
MAA1
MAA2
MAA3
MAA4
MAA5
MAA6
MAA7
MAA8
MAA9
MAA10
MAA11
MAA12
23
24
25
26
29
30
31
32
33
34
22
35
36
3.3V
40
C11
0.1uF
1
14
27
28
41
54
SDQMA1 39
SDQMA0 15
20
21
21
2
38
37
MEMCLK0
CKEA
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
NC
VCC
VCC
VCC
VSS
VSS
VSS
UDQM
LDQM
BS0
BS1
CLK
CKE
IC6
QD0
QD1
QD2
QD3
QD4
QD5
QD6
QD7
QD8
QD9
QD10
QD11
QD12
QD13
QD14
QD15
VCCQ
VCCQ
VCCQ
VCCQ
VSSQ
VSSQ
VSSQ
VSSQ
CAS#
RAS#
CS#
WE#
3_MD0
3_MD1
3_MD2
3_MD3
3_MD4
3_MD5
3_MD6
3_MD7
3_MD8
3_MD9
3_MD10
3_MD11
3_MD12
3_MD13
3_MD14
3_MD15
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
MAA0
MAA1
MAA2
MAA3
MAA4
MAA5
MAA6
MAA7
MAA8
MAA9
MAA10
MAA11
MAA12
23
24
25
26
29
30
31
32
33
34
22
35
36
3.3V
40
3.3V
3
9
43
49
6
12
46
52
C13
C297
0.1uF
0.1uF
1
14
27
28
41
54
17
18
SDQMA5 39
SDQMA4 15
20
21
19
16
38
37
MT48LC8M16A2TG-75
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
NC
VCC
VCC
VCC
VSS
VSS
VSS
UDQM
LDQM
BS0
BS1
CLK
CKE
QD0
QD1
QD2
QD3
QD4
QD5
QD6
QD7
QD8
QD9
QD10
QD11
QD12
QD13
QD14
QD15
VCCQ
VCCQ
VCCQ
VCCQ
VSSQ
VSSQ
VSSQ
VSSQ
CAS#
RAS#
CS#
WE#
3_MD32
3_MD33
3_MD34
3_MD35
3_MD36
3_MD37
3_MD38
3_MD39
3_MD40
3_MD41
3_MD42
3_MD43
3_MD44
3_MD45
3_MD46
3_MD47
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
3.3V
3
9
43
49
6
12
46
52
C299
0.1uF
2
17
18
19
16
MT48LC8M16A2TG-75
21
MEMCLK0
2
2
3
2
IC5
MAA0
MAA1
MAA2
MAA3
MAA4
MAA5
MAA6
MAA7
MAA8
MAA9
MAA10
MAA11
MAA12
23
24
25
26
29
30
31
32
33
34
22
35
36
40
1
14
27
28
41
54
0.1uF
C12
SDQMA3
SDQMA2
39
15
20
21
2
21
38
37
MEMCLK0
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
NC
VCC
VCC
VCC
VSS
VSS
VSS
UDQM
LDQM
BS0
BS1
CLK
CKE
IC7
QD0
QD1
QD2
QD3
QD4
QD5
QD6
QD7
QD8
QD9
QD10
QD11
QD12
QD13
QD14
QD15
VCCQ
VCCQ
VCCQ
VCCQ
VSSQ
VSSQ
VSSQ
VSSQ
CAS#
RAS#
CS#
WE#
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
3
9
43
49
6
12
46
52
3_MD16
3_MD17
3_MD18
3_MD19
3_MD20
3_MD21
3_MD22
3_MD23
3_MD24
3_MD25
3_MD26
3_MD27
3_MD28
3_MD29
3_MD30
3_MD31
MAA0
MAA1
MAA2
MAA3
MAA4
MAA5
MAA6
MAA7
MAA8
MAA9
MAA10
MAA11
MAA12
40
3.3V
C14
C298
0.1uF
0.1uF
SDQMA7
SDQMA6
1
14
27
28
41
54
17
18
39
15
20
21
19
16
38
37
MT48LC8M16A2TG-75
21
23
24
25
26
29
30
31
32
33
34
22
35
36
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
NC
VCC
VCC
VCC
VSS
VSS
VSS
UDQM
LDQM
BS0
BS1
CLK
CKE
QD0
QD1
QD2
QD3
QD4
QD5
QD6
QD7
QD8
QD9
QD10
QD11
QD12
QD13
QD14
QD15
VCCQ
VCCQ
VCCQ
VCCQ
VSSQ
VSSQ
VSSQ
VSSQ
CAS#
RAS#
CS#
WE#
3_MD48
3_MD49
3_MD50
3_MD51
3_MD52
3_MD53
3_MD54
3_MD55
3_MD56
3_MD57
3_MD58
3_MD59
3_MD60
3_MD61
3_MD62
3_MD63
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
3.3V
3
9
43
49
6
12
46
52
C300
0.1uF
17
18
19
16
MT48LC8M16A2TG-75
MEMCLK0
1
A
B
AR-M350U CIRCUIT DIAGRAM 9-16
C
* !"#!$
C
D
E
5
2
MAA[12:0]
2
SDQMA[7:0]
2
3_MD[63:0]
3.3V
3.3V
SDRAM DIMM Slot
CN3
IC6
23
24
25
26
29
30
31
32
33
34
22
35
36
40
3
uF
1
14
27
28
41
54
DQMA5 39
DQMA4 15
20
21
38
37
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
NC
VCC
VCC
VCC
VSS
VSS
VSS
UDQM
LDQM
BS0
BS1
CLK
CKE
QD0
QD1
QD2
QD3
QD4
QD5
QD6
QD7
QD8
QD9
QD10
QD11
QD12
QD13
QD14
QD15
VCCQ
VCCQ
VCCQ
VCCQ
VSSQ
VSSQ
VSSQ
VSSQ
CAS#
RAS#
CS#
WE#
3_MD59
3_MD58
3_MD57
3_MD56
3_MD47
3_MD46
3_MD45
3_MD44
3_MD43
3_MD42
3_MD41
3_MD40
3.3V
3
9
43
49
6
12
46
52
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
3_MD63
3_MD62
3_MD61
3_MD60
3_MD32
3_MD33
3_MD34
3_MD35
3_MD36
3_MD37
3_MD38
3_MD39
3_MD40
3_MD41
3_MD42
3_MD43
3_MD44
3_MD45
3_MD46
3_MD47
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
C299
0.1uF
2
17
18
MWE
SDQMA7
SDQMA5
19
16
MAA0
MAA2
MAA4
MAA6
MAA8
MAA10
MT48LC8M16A2TG-75
2
2
BSEL1A
MCS1A
21
MEMCLK1
IC7
23
24
25
26
29
30
31
32
33
34
22
35
36
40
1
14
27
28
41
54
39
15
20
21
38
37
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10/AP
A11
A12
NC
VCC
VCC
VCC
VSS
VSS
VSS
UDQM
LDQM
BS0
BS1
CLK
CKE
QD0
QD1
QD2
QD3
QD4
QD5
QD6
QD7
QD8
QD9
QD10
QD11
QD12
QD13
QD14
QD15
VCCQ
VCCQ
VCCQ
VCCQ
VSSQ
VSSQ
VSSQ
VSSQ
CAS#
RAS#
CS#
WE#
3_MD48
3_MD49
3_MD50
3_MD51
3_MD52
3_MD53
3_MD54
3_MD55
3_MD56
3_MD57
3_MD58
3_MD59
3_MD60
3_MD61
3_MD62
3_MD63
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
SDQMA3
SDQMA1
3_MD31
3_MD30
3_MD29
3_MD28
3_MD27
3.3V
3
9
43
49
6
12
46
52
2
CKEA
3_MD26
3_MD25
3_MD24
C300
0.1uF
3_MD15
3_MD14
3_MD13
3_MD12
17
18
3_MD11
3_MD10
3_MD9
3_MD8
19
16
MT48LC8M16A2TG-75
21
MEMCLK3
3.3V
R45
10K
R44
10K
GND
DQ32
DQ33
DQ34
DQ35
+3.3V
DQ36
DQ37
DQ38
DQ39
DQ40
GND
DQ41
DQ42
DQ43
DQ44
DQ45
+3.3V
DQ46
DQ47
NC
NC
GND
NC
NC
+3.3V
CE
DQMB4
DQMB5
S1
RE
GND
A1
A3
A5
A7
A9
BA0
A11
+3.3V
CK1
NC
GND
CKE0
S3
DQMB6
DQMB7
NC
+3.3V
NC
NC
NC
NC
GND
DQ48
DQ49
DQ50
DQ51
+3.3V
DQ52
NC
NC
NC
GND
DQ53
DQ54
DQ55
GND
DQ56
DQ57
DQ58
DQ59
+3.3V
DQ60
DQ61
DQ62
DQ63
GND
CK3
NC
SA0
SA1
SA2
+3.3V
GND
DQ0
DQ1
DQ2
DQ3
+3.3V
DQ4
DQ5
DQ6
DQ7
DQ8
GND
DQ9
DQ10
DQ11
DQ12
DQ13
+3.3V
DQ14
DQ15
NC
NC
GND
NC
NC
+3.3V
W(WE0)
DQMB0
DQMB1
S0
NC(OE0)
GND
A0
A2
A4
A6
A8
A10
BA1
+3.3V
+3.3V
CK0
GND
NC(OE2)
S2
DQMB2
DQMB3
NC(WE2)
+3.3V
NC
NC
NC
NC
GND
DQ16
DQ17
DQ18
DQ19
+3.3V
DQ20
NC
NC
NC(CKE1)
GND
DQ21
DQ22
DQ23
GND
DQ24
DQ25
DQ26
DQ27
+3.3V
DQ28
DQ29
DQ30
DQ31
GND
CK2
NC
NC
SDA
SCL
+3.3V
DMM168-FLAA2-3A133
3
3
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
3_MD55
3_MD54
3_MD53
3_MD52
3_MD51
3_MD50
3_MD49
3_MD48
3_MD39
4
3_MD38
3_MD37
3_MD36
3_MD35
3_MD34
3_MD33
3_MD32
2
MCS2A
MRASA
2
2
BSEL0A
CKEA
2
2
MEMCLK2
21
MAA1
MAA3
MAA5
MAA7
MAA9
MAA11
3
MAA12
SDQMA2
SDQMA0
3_MD23
3_MD22
3_MD21
3_MD20
3_MD19
3_MD18
3_MD17
3_MD16
3_MD7
3_MD6
3_MD5
3_MD4
2
3_MD3
3_MD2
3_MD1
3_MD0
MEMCLK4
21
C24
0.1uF
SDA
SCL
1
3.3V
C
MCASA
SDQMA6
SDQMA4
C23
C31
C44
C32
C41
C42
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
D
AR-M350U CIRCUIT DIAGRAM 9-17
E