Download Sandisk SD-ROM User's Manual

SanDisk SD-ROM Product Manual
Revision 1.0
SanDisk Corporation
Corporate Headquarters . 601 McCarthy Boulevard . Milpitas, California 95035
Phone: 408-801-1000 . Fax: 408-801-8657
www.sandisk.com
SanDisk Confidential
SanDisk® Corporation general policy does not recommend the use of its products in life support applications where
in a failure or malfunction of the product may directly threaten life or injury. Per SanDisk Terms and Conditions of
Sale, the user of SanDisk products in life support applications assumes all risk of such use and indemnifies SanDisk
against all damages. See "Disclaimer of Liability."
This document is for information use only and is subject to change without prior notice. SanDisk Corporation
assumes no responsibility for any errors that may appear in this document, nor for incidental or consequential
damages resulting from the furnishing, performance or use of this material. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrievable manner or translated into any language or computer
language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise,
without the prior written consent of an officer of SanDisk Corporation.
All parts of the SanDisk documentation are protected by copyright law and all rights are reserved.
SanDisk and the SanDisk logo are registered trademarks of SanDisk Corporation. Compact Flash is a
U.S. registered trademark of SanDisk Corporation.
Product names mentioned herein are for identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.
© 2007 SanDisk Corporation. All rights reserved.
SanDisk products are covered or licensed under one or more of the following U.S. Patent Nos. 5,070,032;
5,095,344; 5,168,465; 5,172,338; 5,198,380; 5,200,959; 5,268,318; 5,268,870; 5,272,669; 5,418,752; 5,602,987.
Other U.S. and foreign patents awarded and pending.
SanDisk Confidential
1 SD-ROM Card Overview
1.1 Introduction
SanDisk SD-ROM Cards provide permanent and secure read-only data storage for consumer
electronic and personal computer applications. SanDisk SD-ROM Cards are based on
SanDisk’s unique 3D one-time programmable (OTP) memory devices which safely store data
for 100 years. This compares favorably with cards based on flash memory devices, which are
typically rated to store data for 10 years or less. And unlike cards based on mask ROM memory
devices, SanDisk SD-ROM Cards can be programmed immediately before shipping to endusers or retail storefronts, reducing order turn time and inventory requirements.
SanDisk SD-ROM Cards are compatible with the Secure Digital memory card specifications,
with some modifications to maximize host device compatibility. Matsushita Electric Industrial Co.
Ltd., SanDisk Corporation and Toshiba Corporation (SD-3C, LLC) originally defined
specifications for the SD Card. SD card specifications are now maintained, controlled and
assigned by the SD-3C, LLC. While a formal SD-ROM card specification does not yet exist, the
SanDisk SD ROM Card has been designed to be compatible with most SD host devices today.
SanDisk SD-ROM Cards implement the 9-pin SD card interface and support a maximum
operating frequency of 25 MHz and an operating voltage range of 2.7 – 3.6v. The industrystandard SD interface allows for easy integration into any design, regardless of which type of
microprocessor is used. In addition to the SD interface, the SanDisk SD-ROM Card interface
offers an alternate communication protocol based on the SPI standard. With some additions,
the physical form factor, pin assignment, and data transfer protocol are forward compatible with
current and future SanDisk SD Card products.
SanDisk SD-ROM Cards are available in 32, 64, and 128 megabyte (MB) capacities.
1.2 Feature Summary
General features of SanDisk SD-ROM Cards include:
• Archival data storage with over 100 year data storage lifetime
• Convenient form-factor, ideal for portable and stationary applications for content storage
• Card capacities of 32, 64, and 128MB
• Supports industry-standard SD and SPI interfaces
• Voltage range of 2.7 to 3.6V
• Variable clock rate of 0 - 25 MHz
1.3 SD Card Standard
SanDisk SD-ROM Cards are compatible with the SDA Physical Layer Specification, Version
2.00. This specification is available from the SD Card Association (SDA).
SD Card Association 2400 Camino Ramon, Suite 375 San Ramon, CA 94583 USA Telephone:
+1 (925) 275-6615 Fax: +1 (925) 886-4870 E-mail: [email protected] Web site:
www.sdcard.org
SanDisk Confidential
2 SanDisk SD-ROM Card Functional Description
SanDisk SD-ROM Cards are compatible with the SD specifications, with some changes
necessary for a read-only memory.
In an SD host system, the host controls all communication between itself and the cards. For
detailed information, refer to Section 4 of the SDA Physical Layer Specification, Version 2.00.
This chapter contains the functional description for SanDisk SD-ROM Cards.
2.1 SD Bus Protocol
Communication over the SD bus is based on command and data-bit streams initiated by a start
bit and terminated by a stop bit. See Section 3.6.1 of the SDA Physical Layer Specification,
Version 2.00, for details.
2.2 SPI Mode
The SPI Mode is a secondary communication protocol for cards in the SanDisk SD-ROM Cards.
This interface mode is an alternate to the SD protocol and is designed to communicate with an
SPI channel, commonly found in Motorola and other vendors' microcontrollers. More
information about SPI Mode can be found in Section 7 of the SDA Physical Layer Specification,
Version 2.00.
2.3 Cyclic Redundancy Codes
Cyclic Redundancy Codes (CRC) protect against transmission errors that may occur on the bus
in SD systems. Detailed information and examples for CRC7 and CRC16 are provided in
Section 4.5 of the SDA Physical Layer Specification, Version 2.00.
2.4 Clock Control
The host can use the bus clock signal to SanDisk SD-ROM Cards to decrease power
consumption or to control data flow on the bus. See Section 4.4 of the SDA Physical Layer
Specification, Version 2.00.
2.5 Sleep Mode
SanDisk SD Cards implement a feature to automatically enter and exit from sleep mode. Upon
completion of an operation, cards enter sleep mode to conserve power if no additional
commands are received in less than 5 milliseconds (ms). The host does not have to take any
action for this to occur; however, in order to achieve the lowest sleep current, the host should
also shut down its clock to the card. In most systems, cards are in sleep mode except when
accessed by the host, thus conserving power.
When the host is ready to access a card in sleep mode, any command issued to the card will
cause it to exit sleep mode and respond.
2.6 Hot Insertion
SanDisk SD-ROM Cards support hot insertion into a powered host device through SD
connectors that have power pins that make contact before the signal pins. This approach is
similar to that used in PCMCIA and MMCA devices to allow for hot insertion. For more
information, refer to Section 6.1 and Section 6.2 of the SDA Physical Layer Specification,
Version 2.00.
SanDisk Confidential
2.7 Card State Transitions
SanDisk SD-ROM Cards operate the same as standard SD cards, where the state transition is
dependent on the received command along with responses sent on the command line. The
transitions are defined in Section 4.8 of the SDA Physical Layer Specification, Version 2.00
In Card Identification Mode, the host operates the card at a slower frequency as it identifies and
initializes the card. For more information see Section 4.2 in the SDA Physical Layer
Specification, Version 2.00.
In Data Transfer Mode, the host may increase the card interface frequency to the maximum
allowed frequency; it is in this mode that the host issues data read and write and other related
commands. For more detailed information, refer to Section 4.3 of the SDA Physical Layer
Specification, Version 2.00.
Error conditions are described in Section 4.6 of the SDA Physical Layer Specification, Version
2.00.
2.8 Supported Commands
SanDisk SD-ROM Card support the commands in the Basic (class 0), Block Read (class 2),
Application Specific (class 8), and Switch (class 10) command classes only. The commands in
the Write (class 4), Erase (class 5), Write Protection (class 6), and Lock/Unlock (class 7)
command classes are not applicable for a ROM card and are not supported; refer to the next
section for more information.
See the SDA Physical Layer Specification, version 2.00, Section 4.7 for detailed information
about card commands and Section 4.12 for timing diagrams and values.
2.9 SD-ROM Card Functional Behavior
In order to maximize compatibility and host interoperability, even though the SD-ROM card
provides read-only access to its memory contents, it will appear to the host system as a
standard read/write card. This is because many host devices assume all SD cards are
read/write and will reject a ROM-type card.
Specifically, even though the SanDisk SD-ROM card does not support Write (class 4), Erase
(class 5), Write Protection (class 6), and Lock/Unlock (class 7) commands, it will be configured
to report to the host system that it supports those commands by setting the Card Command
Class field in the CSD register to 5F5h. If a command from these groups is issued by the host,
the card will accept the command without generating an error, but will not perform it.
In addition, the card will also appear to be non-write-protected (the PERM_WRITE_PROTECT
and TEMP_WRITE_PROTECT bits in the CSD will be clear). If the host issues a write
command, the card will accept the command without generating an error, but will not perform it.
Finally, the SD-ROM card does not support SD security commands. The SD_Security field in
the SCR register is set to 0h, indicating no security support.
SanDisk Confidential
3 SanDisk SD-ROM Card Specifications
3.1 Operating Specifications
The table below summarizes the SD-ROM operating specifications.
Parameter
Supply Voltage
Value
2.0 – 3.6v
2.7 – 3.6v
Notes
during card identification for version 1.1 cards
all supported commands
Operating Temperature
Storage Temperature
Data Retention
Data Endurance
Interface speed
Read Bandwidth
-25 – 85 °C
-40 – 85 °C
100 years minimum
1x109 read cycles
0 – 25MHz
1.8MB/s minimum
50mA typical
75mA maximum
250uA maximum
300ms
100ms
variable clock rate
sequential read, 25MHz interface speed
Read Current
Sleep Current
Reset to Read Latency
Read Command Response
maximum at 3.6v, 85 °C
3.2 Memory Capacity
SanDisk SD-ROM Cards are sold preloaded with an OEM-specified image which may or may
not have a file system. In general, a file system provides structure for data; the SD Card File
System Specification, published by the SDA, describes the file format system that is typically
implemented on SD cards.
SanDisk SD-ROM cards do not support the SD security features (CPRM), and are therefore
organized as a single non-secure partition. The content data can be accessed by the host
system using standard read commands.
The following table lists the available user space for 32, 64, and 128MB cards. Note that some
hosts cannot handle non-standard image sizes, so the allowable space for a particular
application may be less than shown in the table.
Capacity
32 MB
64 MB
128 MB
Maximum User LBA
63,488
129,024
260,096
Maximum User Data Image Size
31.0MB (32505856 bytes)
63.0MB (66060288 bytes)
127.0MB (133169152 bytes)
3.3 Register Values
The SD specifications define a set of eight registers within the card interface. However, the DSR
Register is optional and is not used in the SanDisk SD Card Product Family. For specific
information about all registers, refer to Section 5 of the SDA Physical Layer Specification,
Version 2.00.
SanDisk Confidential
Register Abbreviation
CID
CSD
SCR
RCA
OCR
SSR
CSR
Width (in bits)
128
128
64
16
32
512
32
Register Name
Card IDentification
Card-Specific Data
SD Configuration Register
Relative Card Address
Operation Condition Register
SD Status Register
Card Status Register
All card registers are also accessible in SPI Mode. Their format is identical to the format in the
SD Bus Mode; however, a few fields are not used in SPI Mode. In SPI Mode, the Card Status
Register has a different, shorter format as well. Refer to Section 7.4 in the SDA Physical Layer
Specification, Version 2.00, for more details.
3.3.1 Card Identification Register
The Card Identification (CID) Register is 16 bytes long and contains the unique card
identification number and other informational data. It is programmed during card content
programming and cannot be changed by card hosts.
The following table lists the default configuration of the CID register for SanDisk SD-ROM Cards.
More information can be found in Section 5.2 of the SDA Physical Layer Specification, Version
2.00.
Name
Type
Size
Value
Manufacturer ID (MID)
binary
8
0x03 (SanDisk)
OEM / Application ID (OID)
ASCII
16
0x53, 0x44 (“SD”)
Product Name (PNM)
ASCII
40
SD032
SD064
SD128
Product Revision (PRV)
Serial Number (PSN)
Reserved
BCD
Binary
8
32
4
Manufacture Date (MDT)
Binary
12
CRC7 Checksum (CRC)
7
unused (always 0)
1
Comments
Controlled and assigned by SD3C, LLC.
Identifies the card OEM and/or
the card contents. Controlled
and assigned by SD-3C, LLC.
5-character ASCII string
2-digit revision number
32-bit unsigned integer
YYM code
(offset from 2000)
ex: April 2001 = 0x014
calculated from register
contents
3.3.2 Card Specific Data Register
The Card Specific Data (CSD) Register configuration information is required to access card data.
The CSD defines the data format, error correction type, maximum data access time, and other
parameters. The field structures of the CSD Register vary depending on the physical
specifications and card capacity. The CSD_STRUCTURE field in the CSD Register indicates
which structure version is used. All current SanDisk SD-ROM are standard capacity cards and
so implement CSD Version 1.0 structure.
The following table provides an overview of the CSD Register. More field-specific information
can be found in Table 5-4 (Section 5.3.2) of the SDA Physical Layer Specification, Version 2.00.
SanDisk Confidential
Field
CSD_STRUCTURE
Reserved
TAAC
Value
1.0
NSAC
0
TRANS_SPEED
CCC
READ_BL_LEN
READ_BL_PARTIAL
WRITE_BLK_MISALIGN
READ_BLK_MISALIGN
DSR_IMP
Reserved
C_SIZE
25MHz
0x5F5
512 bytes
Yes
No
No
No
VDD_R_CURR_MIN
VDD_R_CURR_MAX
VDD_W_CURR_MIN
VDD_W_CURR_MAX
C_SIZE_MULT
ERASE_BLK_EN
SECTOR_SIZE
WP_GRP_SIZE
WP_GRP_ENABLE
Reserved
R2W_FACTOR
WRITE_BL_LEN
WRITE_BL_PARTIAL
FILE_FORMAT_GRP
COPY
PERM_WRITE_PROTECT
TMP_WRITE_PROTECT
FILE_FORMAT
Reserved
CRC
1.5ms
depends on card
size
100mA
80mA
100mA
80mA
depends on card
size
Yes
32 blocks
128 sectors
Yes
x16
512 bytes
No
0
Has been copied
Not protected
Not protected
HD w/partition
CRC7
Comments
CSD structure
Reserved
Data read access time – 1
Data read access time – 2 in CLK cycles
(NSAC*100)
Maximum data transfer rate
Card Command Classes
Maximum read data block length
Partial blocks for read allowed
Write block misalignment
Read block misalignment
DSR implemented
Reserved
Device Size
Maximum read current @VDD minimum
Maximum read current @VDD maximum
Maximum write current @VDD minimum
Maximum write current @VDD maximum
Device size multiplier
Erase single block enable
Erase sector size
Write protect group size
Write protect group enable
Reserved for MMC compatibility
Write speed factor
Maximum write data block length
Partial blocks for write allowed
File format group
Copy flag (OTP)
Permanent write protection
Temporary write protection
File format
Reserved
CRC
Not used, always “1”
3.3.3 SD Card Configuration Register
The SD Card Configuration Register (SCR) provides information about special features in the
SanDisk SD Card products. For more information, refer to Section 5.6 in the SDA Physical
Layer Specification, Version 2.00.
SanDisk Confidential
3.3.4 Card Status Register
The Card Status Register (CSR) transmits the card's status information to the host. The CSR is
defined in Section 4.10.1 in the SDA Physical Layer Specification, Version 2.00.
3.3.5 SD Status Register
The SD Status Register (SSR) contains status bits that are related to the SD Card proprietary
features and may be used for future applications. The SD Status structure is described in
Section 4.10.2 in the SDA Physical Layer Specification, Version 2.00.
3.3.6 Relative Card Address Register
The 16-bit Relative Card Address (RCA) Register carries the card address published by the
card during the card identification process. Refer to Section 5.4 in the SDA Physical Layer
Specification, Version 2.00 for more information.
3.3.7 Operation Conditions Register
The Operation Conditions Register (OCR) stores a card's VDD voltage profile. Refer to
Section 5.1 of the SDA Physical Layer Specification, Version 2.00 for more information.
3.4 Bus Topology
The family of SanDisk SD products supports two communication protocols: SD and SPI. For
more details, refer to Section 3.5 of the SDA Physical Layer Specification, Version 2.00. Section
6 of the specification contains a bus circuitry diagram for reference.
NOTE: SD Card pin assignments are provided by the SDA Physical Layer Specification, Version
2.00; refer to Section 8.2.
#
1
2
3
4
5
6
7
8
9
SD Bus Mode Pin Assignment
Function
I/O Type Description
Card Detect /
CD/DAT31,2 push-pull
Data [bit 3]
Command /
CMD
push-pull
Response
supply
Supply
Ground
VSS1
supply
Supply Voltage
VDD
SPI Bus Mode Pin Assignment
Function
I/O Type Description
input
CS1
Chip Select (active low)
DataIn
supply
supply
Clock
Supply Ground
VSS1
VDD
SCLK
VSS2
output
CLK
VSS2
input
supply
DAT0
push-pull
Data [bit 0]
DataOut
push-pull
push-pull
Data [bit 1]
Data [bit 2]
RSV
RSV
2
DAT1
DAT22
input
input
supply
Host-to-Card
commands and data
Supply Ground
Supply Voltage
Clock
Supply Ground
Card-to-Host Data and
Status
Reserved
Reserved
Notes:
1. At power up this line has a 50KOhm pullup enabled in the card. This resistor serves two
functions: Card Detection and Mode Selection. For Mode Selection, the host can drive the
line high or let it be pulled high to select SD mode. If the host wants to select SPI mode it
should drive the line low. For Card detection, the host detects that the line is pulled high.
This pull-up should be disconnected by the user, during regular data transfer, with the
SET_CLR_CARD_DETECT (ACMD42) command.
2. The extended DAT lines (DAT1-DAT3) are input on power up. They start to operate as DAT
lines after the SET_BUS_WIDTH command. It is the responsibility of the host designer to
SanDisk Confidential
connect external pullup resistors to all data lines even if only DAT0 is to be used. Otherwise,
non-expected high current consumption may occur due to the floating inputs of DAT1 and
DAT2 (in case they are not used).
For more details regarding the SD Bus topology, refer to Section 3.5.1 of the SDA Physical
Layer Specification, Version 2.00.
For more details regarding the SPI Bus topology, refer to Section 3.5.2 of the SDA Physical
Layer Specification, Version 2.00.
3.5 Electrical Interface
The power scheme of SanDisk SD products is handled locally in each card and in the bus
master. Refer to Section 6.4 of the SDA Physical Layer Specification, Version 2.00.
3.5.1 Power Up
Refer to Section 6.4.1 of the SDA Physical Layer Specification, Version 2.00, for information
about power sequencing.
3.5.2 Bus Operating Conditions
SPI Mode bus operating conditions are identical to SD Card Bus Mode operating conditions. For
details, see Section 6.6 of the SDA Physical Layer Specification, Version 2.00.
3.5.3 Bus Timing
SanDisk SD-ROM cards operate at a maximum clock frequency of 25MHz. See Section 6.7 of
the SDA Physical Layer Specification, Version 2.00, for bus timing specifications.
3.6 Physical / Mechanical
The following table specifies the physical attributes of the SanDisk SD Card.
Parameter
Weight
Length
Width
Thickness
Value
2.0g maximum
32mm +/- 0.1mm
24mm +/- 0.1mm
2.1mm +/- 0.15mm
Notes
SanDisk SD-ROM Cards are available in an SD card compatible form factor without a physical
(sliding) write-protect switch. As shown in the following package diagram, the SD-ROM Card
package has the write-protect "notch” in the write-enabled position, even though the card itself
is read-only.
SanDisk Confidential
SanDisk Confidential