Download Philips DVP3320/55 User's Manual

DVP3320
DVP3320/55
Service Manual
TABLE OF CONTENTS
Page
. Technical Specifications…………....………………………..............1-2
. Safety Instruction, Warning & Notes….……………………....….....1-3
. DFU Instruction..............................................................................2-1
. Mechanical and Dismantling Instructions…………........................3-1
. Software Version & Upgrades, Region Code Change..……..........4-1
. Trouble Shooting Chart…………………..……………………………
. 5-1
. Wiring Diagram………………………………………..………..….….6-1
. Electrical Diagrams and Print-layouts..….…………………....….…7-1
. Set Mechanical Exploded view & Part list.…………………..….….8-1
. Revision List..................................................................................9-1
©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by FK-0912 BU AVM
Version 1.0
Printed in The Netherlands
Subject to modification
CLASS 1
LASER PRODUCT
GB
3141 785 33870
PHILIPS
1-2
Specification
Note
• 6SHFLÀFDWLRQDQGGHVLJQDUHVXEMHFWWRFKDQJH
without notice.
Accessories supplied
• Remote control and batteries
• Audio/video cables
• Power cable
Playback media
• DVD-Video, Video CD/SVCD, Audio CD,
CD-R/CD-RW, DVD+R/+RW, DVD-R/RW, Picture CD, MP3-CD, WMA-CD,
86%ÁDVKGULYH
USB
• Compatibility: USB
• Class support: UMS (USB Mass Storage
Class)
TV standard
• Number of lines:
• 625 (PAL/50Hz); 525 (NTSC/60Hz)
• Playback: Multi-standard (PAL/NTSC)
Video performance
• Video DAC: 14 bits, 108 MHz
• Y Pb Pr: 0.7 Vpp ~ 75 ohm
• Video output: 1 Vpp ~ 75 ohm
Video format
• Digital compression:
• MPEG 2: DVD/SVCD
• MPEG 1: VCD
• Horizontal resolution:
• DVD: 720 pixels (50 Hz); 720 pixels
(60 Hz)
• VCD: 352 pixels (50 Hz); 352 pixels
(60 Hz)
• Vertical resolution:
•
•
DVD: 576 pixels (50 Hz); 480 pixels
(60 Hz)
VCD: 288 lines (50 Hz); 240 lines
(60 Hz)
Audio performance
• DA converter: 24 bits, 192 kHz
• Frequency response:
• DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz
- 44 kHz (96 kHz)
• SVCD: 4 Hz - 20 kHz (44.1 kHz); 4
Hz - 22 kHz (48 kHz)
• CD/VCD: 4 Hz - 20 kHz (44.1 kHz)
• Signal-Noise (1 kHz): > 90 dB (Aweighted)
• Dynamic range (1 kHz): > 80 dB (Aweighted)
• Crosstalk (1 kHz): > 90 dB
• Distortion/noise (1 kHz): > 65 dB
• MPEG MP3: MPEG Audio L3
Audio format
• Digital:
• MPEG/AC-3/PCM: Compressed
digital (16, 20, 24 bits fs, 44.1, 48, 96
kHz)
• MP3 (ISO 9660): 96, 112, 128, 256
kbps & variable bit rate fs, 32, 44.1,
48 kHz
• Analog sound stereo
• Dolby surround compatible downmix
from Dolby Digital multi-channel sound
Connections
• Y Pb Pr output: Cinch 3x
• Video output: Cinch (yellow)
• Audio output (L+R): Cinch (white/red)
• Digital output:
• 1 coaxial: IEC60958 for CDDA/
LPCM; IEC61937 for MPEG 1/2,
Dolby Digital
Main unit
• Dimensions (w x h x d): 360 x 37 x 209
(mm)
• Net Weight: approximately 1.3 kg
Power
• Power supply rating: 110 V - 240 V; 50/60
Hz
• Power consumption: < 10 W
• Power consumption in standby mode: <
1W
/DVHUVSHFLÀFDWLRQ
• Type: Semiconductor laser InGaAIP
(DVD), AIGaAs (CD)
• Wave length: 655 nm (DVD), 790 nm
(CD)
• Output Power: 10 mW (DVD), 5 mW
(VCD/CD)
• Beam divergence: 60 degrees
1-3
Safety instruction, Warning & Notes
Safety instruction
1. General safety
2.Laser safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol
,
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
This unit employs a laser. Only qualified service personnel
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type
: Semiconductor laser GaAlAs
Wavelength
: 650nm (DVD)
: 780nm (VCD/CD)
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
Output power
attention to the following points:
. Route the wires/cables correctly, and fix them with the
. Check the insulation of the mains lead for external
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
Repair
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
damage.
4)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
mounted cable clamps.
3)
: 7mW (DVD)
: 10mW (DVD /CD)
or
correct
unit
when
¡
measurement is less than 1M .
the
resistance
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
beam.
1-4
Warning
1.General
2. Laser
. All ICs and many other semiconductors are susceptible to
. The use of optical instruments with this product, will
electrostatic discharges (ESD). Careless handing during
increase eye hazard.
repair can reduce life drastically. Make sure that, during
. Only qualified service personnel may remove the cover
repair, you are at the same potential as the mass of the
or attempt to service this device, due to possible eye
set by a wristband with resistance. Keep components and
injury.
tools at this same potential. Available ESD protection
with a disc loaded inside the player.
equipment:
1)
. Repair handing should take place as much as possible
Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
. Text below is placed inside the unit, on the laser cover
shield:
4822 310 10671.
2)
Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
Notes:
service
Laboratories. The double-D symbol is trademarks of Dolby
the
player.
Service
personnel
must
take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
Manufactured
under
licence
Laboratories, Inc. All rights reserved.
from
Dolby
1-5
Notes
Lead-Free requirement for service
INDENTIFICATION:
x
Regardless of special logo (not always indicated)
Use only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
One must treat all sets from 1.1.2005 onwards, according
next rules.
companies.
x
Important note: In fact also products a little older can also
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Special information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering
always
use
highest
lead-free
temperature profile, in case of doubt)
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
- lead free BGA-ICs will be delivered in so-called
x Use only lead-free solder alloy Philips SAC305 with
‘dry-packaging’ (sealed pack including a silica gel
order code 0622 149 00106. If lead-free solder-paste is
pack) to protect the IC against moisture. After
required, please contact the manufacturer of your
opening, dependent of MSL-level seen on
solder-equipment. In general use of solder-paste within
indicator-label in the bag, the BGA-IC possibly
workshops should be avoided because paste is not easy
still
to store and to handle.
communicated via AYS-website.
to
be
baked
dry.
This
will
be
Do not re-use BGAs at all.
x Use only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
has
x
For sets produced before 1.1.2005, containing
o To reach at least a solder-temperature of 400°C,
leaded soldering-tin and components, all needed
o To stabilize the adjusted temperature at the
spare-parts will be available till the end of the
solder-tip
o To exchange solder-tips for different applications.
x Adjust your solder tool so that a temperature around
360°C – 380°C is reached and stabilized at the solder
joint. Heating-time of the solder-joint should not exceed
service-period. For repair of such sets nothing
changes.
x On our website:
www.atyourservice.ce.Philips.com
You find more information to:
~ 4 sec. Avoid temperatures above 400°C otherwise
BGA-de-/soldering (+ baking instructions)
wear-out of tips will rise drastically and flux-fluid will be
Heating-profiles of BGAs and other ICs used in
destroyed. To avoid wear-out of tips switch off un-used
Philips-sets
equipment, or reduce heat.
x Mix of lead-free solder alloy / parts with leaded solder
You will find this and more technical information
alloy / parts is possible but PHILIPS recommends
within the “magazine”, chapter “workshop news”.
strongly to avoid mixed
For additional questions please contact your local
solder alloy types (leaded and lead-free). If one cannot
repair-helpdesk.
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
2-1
Opens or closes the disc
compartment.
•
Product overview
c DISC MENU
• Accesses or exits the disc menu.
• Switches to disc mode.
• For VCD and SVCD, turns PBC
(playback control) on or off in PBC
mode.
Main unit
d
•
•
6
a
•
(Standby-On)
Turns on the DVD player or switches
to standby mode.
b Disc compartment
•
e
c Display panel
d
(Open/Close)
• Opens or closes the disc
compartment.
e
•
(Play/Pause)
Starts, pauses or resumes disc play.
•
(USB) jack
&RQQHFWD86%ÁDVKGULYH
f
(Navigation buttons)
Navigates through the menus.
Searches fast-forward (right) or fastbackward (left). Press repeatedly to
change the search speed.
Searches slow-forward (up) or slowbackward (down). Press repeatedly
to change the search speed.
BACK
Returns to the previous menu.
For DVD, navigates to title menu.
For VCD version 2.0 or SVCD with
PBC turned on, returns to the menu.
•
•
•
f
/
•
•
g
Remote control
•
(Previous/Next)
Skips to the previous or next title,
chapter, or track.
Press and hold for fast-backward or
fast-forward search.
(USB)
Switches to USB mode and displays
the content.
1
2
3
18
4
17
5
16
6
7
15
14
8
9
13
10
12
11
a
b
(Standby-On)
• Turns on the DVD player or switches
to standby mode.
(Open/Close)
h Numeric buttons
• Selects an item to play.
i SUBTITLE
• Selects the subtitle language on a
disc.
j
ZOOM
Fits the picture format to the TV
screen.
• Zooms in or out of the picture.
•
k REPEAT
• Toggles between various repeat
modes.
l REPEAT A-B
2-2
•
Marks the section for repeat play, or
turns off repeat mode.
m AUDIO
• Selects an audio language or channel
on a disc.
n
•
o
•
p
(Stop)
Stops disc play.
(Play/Pause)
Starts, pauses or resumes disc play.
INFO
For discs, displays information about
the current status or the disc.
• For slideshows, displays a thumbnail
YLHZRISKRWRÀOHV
•
q OK
• &RQÀUPVDQHQWU\RUVHOHFWLRQ
r SETUP
• Accesses or exits the setup menu.
3-1
Mechanical and Dismantling Instructions
Dismantling Instruction
Detailed information please refer to the model set.
The following guidelines show how to dismantle the player.
Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1).
Figure 1
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2)
Note: Make sure to operate gently otherwise the guider would be damaged.
Please kindly note that dismantle
the front door
assembly carefully to avoid damage tray and the front door.
Figure 2
3-2
Mechanical and Dismantling Instructions
Detailed information please refer to the model set.
Dismantling Instruction
Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3).
Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 3
Step4: Dismantling Front Panel, disconnect the connectors (XP1), need release 4 snaps of Front Panel
and 2 snaps of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6)
XP7
XP5
XP6
XP8
XP9
Figure 4
XP10 XP2
XP1
3-3
Mechanical and Dismantling Instructions
Detailed information please refer to the model set.
Dismantling Instruction
Figure 5
Step5: Dismantling Loader, disconnect the 3 connectors (XP7, XP8, XP9 ) aiming in the below figure, and remove 1 screw that
connects the loader and the bottom cabinet. (Figure 5 & 6)
Figure 6
3-4
Mechanical and Dismantling Instructions
Dismantling Instruction
Detailed information please refer to the model set.
Step6: Dismantling Main Board, first disconnect the connector (XP2), and then remove 4 screws. (Figure 7)
Step7: Remove the 4 screws on Power Board to dismantle the Power Board. (Figure 7)
Figure 7
4-1
Software upgrade
B. Read out the Firmware version to confirm the
How to upgrade the software
1)
A.
Burn the data onto a blank CD-R or RW disc.
Procedure for software upgrade:
1) Power on the set and insert the prepared Upgrade
upgrading
1)
Power on the set and Open the tray door.
2)
Press <9><6><6>button to check the software
information.
The software version and other information are
display on the TV screen as follows:
CDR.
2) The set will starts reading disc & response with
the following display TV screen:
FE Version: XXXX.XXXXXX
DSP Version: DSP.XX
Loading
Firmware Upgrade Erase and program.
OK
BE Version: DVP33XX_XX.XX
Region Code: X
Cancel
Select OK to start upgrade.
3)
Press <OK> button to confirm, then screen will
display :
Firmware Upgrade Programming, Please Wait...
Do not Switch the Player Off !
4)
The upgraded disc will automatically out when
files coping complete, then take out the disc.
5)
About 1 minute later, the tray will automatically
close when upgrading complete.
Region Code Change
1) Power on the set and open the tray door;
2) Press "9" "8" "7" "9" and press the region
code number (0-6) on the remote control.
Notes:restart after above steps.
Caution: The set must not be power off during
upgrading, Otherwise the Main board will be
damaged entirely.
Trouble shooting chart
5-1
Spindle motor does not move
Motor no move
Go
Check the FFC connection
No
Correct connection
between 24P and the loader.
Yes
Check whether “RFA5V”
No
Check
(+5V) voltage is normal.
the
RFA5V
power
supply
Yes
Check whether laser voltage
No
(2.3V for DVD & 1.9V for CD)
Check/Replace Q4ǃQ5.
on Collector of Q4 and Q5
Yes
1.Whether voltage on pin 97 of U2
No
varies between 0 and 3.3V (3.3V for
CD and 0V for DVD),
Check/ Replace U2.
2.Whether peripheral components
are eroded or badly soldered.
Yes
Have no
focus
No
1.
Check U2 pin89 FOCUS_PWM
signals
2.If there are F+, F-, T+ and Tsignals output from U4.
Yes
Check/Replace the loader
FOCUS_PWN waveform
Trouble shooting chart
5-2
The power can not be on or off
The power can’t be
on or off
Go
Check the power supply
No
Repair the power board
on the power board is
normal.
Yes
Check if the CON2 on the
Check/Correct
No
power board to XP2 on the
Yes
connection
decoder board is in good
contact.
Yes
Check
if
the
xp1
on
the
decoderboard to XS301 on the
frontboard is in good contact
Yes
No
Correct the connection
5-3
All output voltages on the power board is 0V or deviated.
Trouble shooting chart
All output voltages on
the power board is 0V or
deviated
Yes
Check whether
Yes
Replace F1
F1 is blown
No
Check whether there is
Replace C1&C2 if D1, D2, D3, D4 are
No
normal.
300V on C1 or C2.
Yes
Check whether 100KHz
oscillating signal on
Pin6 of U1
No
Check/ replace U1.
U1(PIN 3 - RC waveform)
U1(PIN 8 - Drain waveform)
Yes
Check if +5V,
+12V are
short.
Yes
Check whether the components in the
short-circuit voltage are defected or eroded.
No
Check whether U1 are eroded.
Trouble shooting chart
5-4
Disc cannot be read.
Disc cannot be read.
Yes
Check the FFC connection
No
Check the loaded circuit
between 24P and the loader.
Yes
1.Check voltage on pin 97 of U2 varies
Check whether there is laser
voltage (2.3V for DVD and 1.9V
No
between 0 and 3.3V:
Æ3.3V for CD
Æ0V for DVD
for CD) on Collector of Q4 &Q5
2.Check whether peripheral components
are eroded or defect
Yes
Check
U2,
U4,
and
No
peripheral components are
Re-solder or replace the defective parts
eroded or badly soldered.
Yes
Check if there is RFO signal on
pin10 of XP7. (The normal RFO
No
Check U1 and peripheral components
signal is a clear reticulated wave)
Yes
Check the connection
between U2
Yes
Replace U2 or loader.
No
Correct connection
Trouble shooting chart
5-5
Only DVD disc or only disc except DVD can be played
Only DVD disc, or only disc
except DVD can be Played.
Go
Check
the
FFC
connection between
24pin and the loader.
No
Check the loaded circuit
Yes
Check laser voltage (2.3V) output
Check the solder status on U2 and
No
on Collector of Q4 if pin87 of U2 is
peripheral components
at low level.
Yes
No
Check whether there
is voltage variance on
pin 88 of U2.
check if bad solder exist on U2 and
peripheral components
Yes
Check whether pins of U2 and
peripheral
components
No
are
badly soldered, defected
Replace the bad spare parts
Yes
Check Q4 whether
in good condition
Yes
Change U2 or the loader.
No
Correct connection
Trouble shooting chart
5-6
No display on LED, and buttons do not work
No display on LED, and
buttons do not work
Yes
Check whether there is
correct
contact
between
No
Correct connection
XS301 and XP1
Yes
Check VCC(+5v) voltage
on the power and front
No
Fix power supply board top
a power supply for should
electric circuit
board
Yes
Check there are CS, DATA
and CLK signals on XS301
on the front board.
No
Check the U2’s pin 48,95,96 arrive
the XP1 connect condition
XP1 (PIN 1 CLK)
XP1 (PIN3 DOUT)
Yes
1.Check whether bad solder exists on
U600 and pins of LED,
2.Check whether the circuit connected to
K301,K302,is broken,
3.Check whether R303,R301,R302 are
open-circuit.
Yes
Replace U301 or LED
No
Correct connection
5-7
Distorted audio and loud noise
Distorted audio and
loud noise
Yes
Check whether the output of
Check the power supply voltages
No
+12VA
the power board is normal.If
abnormal ,change the power
board
Yes
Check whether R73
and R77 are normal
No
Replace R77 and R73
Yes
Check
muting
whether
the
transistor
No
Replace Q8,Q10 ,Q12
Q8,Q10.Q12 are normal
Yes
Checking the U5 leads the
No
feet has no to break to
open
&RUUHFWFRQQHFWLRQ
Yes
Check whether the U7 or
U8 powersupply normal
Yes
Replace U7 or U8
No
Check U7,U8
Trouble shooting chart
Trouble shooting chart
5-8
Abnormal color of video picture
Abnormal color of
video picture
Yes
Check
whether
the
No
Check Y2, R28, C31 and C33
27MHz output signal
Yes
Check whether the 3.3V
and 1.8V power supply
voltages on the decoder
board are normal.
No
Check other of power supply electric
circuit
Yes
Check whether the
video filter network
circuit is normal.
No
Correct the connection
Yes
Check if the video signals on Pin
58,60,61,63 of U1 are normal.
No
change U2
Trouble shooting chart
5-9
Remote reception is insensitive or fails.
Remote reception is
insensitive or fails.
Go
Check if the remote
control works properly.
No
Check battery
Yes
Check if the power supply
No
Check
voltage to the remote censor
L2
is normal
Yes
Use an oscilloscope to check if there is
No
output waveform from the first pin IR of the
IR600 (PIN1 - RC waveform)
remote censor after pressing button on the
remote control.
Yes
Check if there is IR
signal on pin 49 of U2
Yes
Change U2
IR waveform
No
Correct connection
Trouble shooting chart
5-10
No video picture, no sound.
No video picture,
no sound.
Check whether all the voltages
No
Check the loaded circuit
from the power board to the
CVBS(R1 point) waveform
decoder board are normal.
Yes
Check if the reset circuit consisting
of CE3, D6 and R21 is normal (at a
No
Change CE3, D6 and R21.
high level for tens of milliseconds,
then constantly at 3.3V).
27Mhz waveform
Yes
Check whether there is
Crystal oscillator Y2 and
No
peripheral components
27MHz signal output.
are defected or eroded.
Yes
Check if there is 135MHz
No
signal output on R31.
Check whether
short-circuit or bad
solder on U1,U3
SDRAM(R31 PCLK) waveform
No
Yes
Check if short-circuit and
bad solder exist on Pin 60
Check U2.
No
Yes
Reconnect the component in
Yes
6-1
6-1
A
B
C
D
E
DVP3320(2CH+USB) WIRING DIAGRAM
4
4
COAX
Pr
Y
Pb
CVBS
R
L
XP5
P1
AUDIO
AMP&LPF
VIDEO LPF&DRIVE
24
XP7
24PIN*0.5
1
2
XP9
5PIN*2.0
64M/16M
SDRAM
AM5888S
6
1
LOAD+
LOADTROUT
GND
TRIN
MOTER
DRIVER
1
1
SPSP+
LIMIT
GND
SLSL+
6PIN*2.0
XP8
ZR36966XE2/XF2
GND
+12V
G ND
5
5
XP11
4PIN*2.0
1
1
6
2
4
XS302
1
XS301 (3-8PIN)
6PIN*2.0
4PIN*2.0
1
4
4PIN*2.0
LED-
POWER+
POWER-K
6
USB
1
LED+
XP601 (4-7PIN)
4
SWITCH
XP1
BOARD 4PIN*2.0
4
CON2
5PIN*2.5
+5V
IR
5V
GND
DATA
CS
CLK
MAIN BOARD
MP-1
+5V
3
8M/16M
FLASH
XP1
6PIN*2.0
5
1
POWER
SUPPLY
1
ASA + SANYO DV38
3
P2
XP2 5PIN*2.5
DVD LOADER
DOWN-LOAD
1
1
A
B
C
D
E
7-1
7-1
5
4
3
2
1
Front Board Electric Diagram for DVP3320:
VCC
D
U5V
D
R315
REM301
)5200$,1%2$5'
5
5
4
4
VCC
GND
IR
3
2
1
100 ohm R318
IR
1
2
3
4
100R/NC
+
for dvp331x
IR
VCC
GND
DATA
CS
CLK
1
2
3
4
5
6
7
8
9
10
11
C306
0.1u
C315
47p
WAKE_SW
U5V
R320
0R
U5V
STB_LED
XS302
CON4(2.0)
REM
XS301
LED+
LEDPOWER_K1
POWER_K
CE301
47uF
C316
100p
C307
100p
C308
100p
IR
V CC
DATA
CS
CLK
VCC
POWER_K
STB_LED
R303 R304 R305
5VL
CON11(2.0)
LEDC309 C310
0.1uF 0.1uF
R306
4K7
4K7
4K7
R317 33R
51K
U301
ET6202
C
DATA
CLK
CS
R300
R301
R302
1
2
3
4
5
6
7
8
9
10
11
12
13
14
100
100
100
R307
R308
10K
10K
R309
R310
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
C300 C301 C302
100P 100P
100P
C303
1K
1K
CE300
+
0.1u
LED1
GRID[1:7]
OSC
DI/O
CLK
STB
KEY1
KEY2
VDD
SEG1/KS1
SEG2/KS2
SEG3/KS3
SEG4/KS4
SEG5/KS5
SEG6/KS6
SEG7/KS7
GND
GRID1
GRID2
GND
GRID3
GRID4
GND
VDD
SEG14/GRID5
SEG13/GRID6
SEG12/GRID7
SEG10/KS10
SEG9/KS9
SEG8/KS8
28
27
26
25
24
23
22
21
20
19
18
17
16
15
GRID1
GRID2
GRID3
GRID4
5VL
GRID7
GRID6
GRID5
LED+
GRID1
GRID2
GRID3
GRID4
GRID5
GRID6
GRID7
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
1
2
3
4
5
6
7
8
9
10
11
12
13
R316 33R
C
GRID1
GRID2
GRID3
GRID4
GRID5
GRID6
GRID7
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
JDD350501AG
47uF
SEG[1:6]
K302
KEY1
KEY2
K301
B
1N4148
D301
R312
1N4148
D302R311
1K
1K
R313
KS2
1K
WAKE_SW
POWER_K
B
R314
R319
0R
play/pause
open/close
0R/nc
POWER_K1
C304
100p
C305
100p
A
A
5
4
3
2
1
7-2
A
7-2
B
C
D
E
Switch Board Electric Diagram for DVP3320:
1
1
K303
1
2
3
4
2
XP1
CON4(2.0)
POWER
2
LED3
C319
47p
SWITCH
C317
47p
C318
47p
BOARD
3
3
4
4
A
B
C
D
E
7-3
7-3
1
2
3
4
5
OK Board Electric Diagram for DVP3320:
A
A
R210
12V
12VA
R202
12VA
CE200
CE201
22uF
22uF
R203
22K
C205
47p
R205
180K
B
C210
2
20K
C211
100K
1
2.2uF
R200
10K
U5A
3
C203
2.2uF/NC
NJM4558 OPA
CE202
8
R201
1
2
3
4
R211
8
KARAOKE
47-EAR024-XX0
ĭ3.5mm
0.1u
+
P601
KARAOKE INPUT
22K
-
1000p
5
REF
12VA
C208
100p
10uF
C204
100p
C
6
NJM4558 OPA
+
MIC_OUT
7
4
B
REF
C201
150
U5B
C
R206
R207
100K
20K
C206
47p
C209
2.2uF
R208
MIC_OUT
MIC
12V
1K
D
1
2
3
D
R209
3PIN/2.0mm
XP601
750R
E
E
1
2
3
4
5
7-4
7-4
A
B
C
D
E
Power Board Electric Diagram for DVP3320:
1
1
F1
T2AL/250ac
TR1
NTC 10&20
D1
1N4007
2
1
P3
D2
1N4007
+
+
1
+
2
+
L1
CON1
AC INPUT
680uH
RV1
10K471
AC INPUT
+ C1
D3
1N4007
1
1
AC INPUT
C N1
D4
1N4007
+ C2
10uF/400V(250V/450V)
P2
15uF/400V(250V/450V)
L6
⺕⦴
T1
EEL19
5
D5
FR102
R2
R3
1/4W120K 1/4W120K
4
C3
+
C5
152/1KV
10uF/50V
6
CON2
6
5
4
3
2
1
7
2
3
R4
D8
IN4007
D7
FR102
9
+
C6
47uF/25V
1/6W10k
-22V
GND
+12V
GND
+5V
+5V
2
6X2.5 HEADER
C9
104/50V
8
1
D10
SR360/SR340
12
R1
NU
C14
NU
L2
6.8uH
EN/UV
+
10
1/6W22
S
+
C7
1000uF/16V
C8
470uF/16V
R5
1/6W12K 1%
R10
1/6W100
R13
8
4
1/6W100k
1
S
S
7
6
S
U1
TNY176/177
5
11
1
2
BP/M
3
NC
Drain
4
R11
R8
1/6W1k
C11
0.1uF/63V
R9
1/6W10k
3
2
3
U2
PC123X92
1
R7
1/6W11.3k 1%
2
U3
TL431
3
3
CY1
102/400Vac
* CAUTION :
THE PARTS MARKED WITH
ARE IMPORTANT PARTS ON THE SAFETY.
PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL.
4
4
A
B
C
D
E
7-5
7-5
A
B
C
D
E
R1
0R
CE1
DSPVCC33
CVBS_C
CVBS_C
L1
0R
RCA_CVBS_OUT
+
Main Board Electric Diagram for DVP3320: Power
C1
150pF
220uF/16V
C2
100pF
R2
4.7K
1
1
XP1
6PIN/2.0mm
CLK
CS
DAT
GND
LED_5V
IR
R90
R91
R86
1
2
3
4
5
6
100R
100R
100R
FPC_CLK
FPC_STB
FPC_DOUT
L2
R3
500
33R
FPC_CLK
FPC_STB
FPC_DOUT
M5V
Imax 60mA
Y_R_V
Y_R_V
L3
IRRCV
0R
V_OUT
C3
150pF
C4
150pF
C10
100p
C5
C6
C8
C7
0.1uF 100pF 100pF 100pF
CVBS_G_Y
CVBS_G_Y
L4
0R
Y_OUT
C11
150pF
2
C12
150pF
2
M5V
RFA5V
RFA5V
Imax=17mA
C13
10nF
C_B_U
C_B_U
L6
0R
U_OUT
C14
150pF
C15
150pF
TO POWER BOARD
Imax 800mA
U11
V_OUT
XP2
1
2
3
4
5
+P12V
U_OUT
6
2
5
3
4
RCA_CVBS_OUT
Y_OUT
P1
RCA/AUDIO OUT
5PIN/2.5mm
PESD3V3L5UY
20mA
1
2
3
4
5
6
R9
C16
0.1uF
C17
0.1uF
RCA_CVBS_OUT
Y_OUT
U_OUT
V_OUT
[NM]
Q3
4.7K
Q2
BT3904
1
2
1
2
1
1
C18
47pF
D12
PESD5V0S(L)1BA
LED/PCON
D11
PESD5V0S(L)1BA
R7
PCON
2
4.7K
D10
PESD5V0S(L)1BA
C88
0.1uF
R6
2
R13
4.7K
PESD5V0S(L)1BA
D9
DSPVCC33
LED/PCON:
L: STBY.
H:
Working.
4
A
3
+12V
8550D
R12
22K
RCA
47-RCA151-XX1
3
M5V
1
4
B
C
D
E
7-6
7-6
A
B
C
D
RESET Circuit
Important power supply!
DSPVCC33I
INSW
DRVSB
IN_OUT_SW
CLOSE
OPEN
HOMESW
INSW
DRVSB
IN_OUT_SW
CLOSE
OPEN
HOMESW
R97
15k
Main Board Electric Diagram: Vaddis_SDRAM_Flash
URST#
R98
3.3k
C19
10nF
2N3904
CE19
10uF/16v
CEL5-5
C89
120MA
L7
1uF
8
7
6
5
R19
0.1U
RFN
R FP
C26
10nF
VFE_YIN
R F_F
SPDL_SENS+
R F_E
SPDL_SENSR F_D
R F_C
DSPVCC33
500
RF_B
RF_A
VFE_YIN
R F_F
SPDL_SENS+
RF_E
SPDL_SENSR F_D
R F_C
C27
0.1U
9MA
VDDAFE
R F_B
R F_A
VDDPLL
R18
4.7
DSPVCC18
C29
0.1U
VDDAFE
15.4K 1%
0.1uF
VC
RESOUT
V REF
VC
R15
C25
LD_DVD
LD_CD
MD_DVD
MD_CD
165MA
L8
VDD DAC
SFDO
SF DI
[FUSE(500MA)]
SFCLK R85
XP11
R104
PCON
27R/NC
R105
27R/NC
SFDO_0
SFDI_0
33R
SFCLK_0
USB_DP
USB_DN
USB5V
C91
R107
C92
RAMADD2
RAMADD6
RAMADD1
RAMADD7
C90
15K/NC 0.1U
15K/NC
RAMADD4
RAMADD3
RAMADD5
0.1U
Gen_4/VID7
SFCS
GND
SFDO/RS_SF
SFDI/RS128_Bootsel2
VDDC
VDDP
SFCLK/RS128_Bootsel1
GPIO[5]
SD_D/IGPIO[7]
PWM5
SD_CMD/GPIO[6]
SD_CLK/IGPIO[7]
VDDP
DP
DN
RAMADD[4]
RAMADD[3]
RAMADD[5]
VDDIP
RAMADD[2]
RAMADD[6]
RAMADD[1]
RAMADD[7]
VDDC
GND
R23
392 Ohm 1%
RSET
DAC1
VDDDAC
DAC2
DAC3
VDDDAC
DAC4
GNDC
XIN
XO
VDDPLL
GNDPLL
RESET#
VDDC
VDDP
IGPIO[44]
GPIO[43]/DUPRD0/TDO/SSCTXD
GND
GPIO[32]/SPDIFO
VDDP
GPIO[29]/AMCLK/APWM0GPIO[28]/APWM1GPIO[26]/APWM2GPIO[25]/AOUT2/APWM3GPIO[24]/DUPRD1/ALRCLK/APWM4IGPIO[23]/DUPTD1/ABCLK/APWM5-
Vaddis-966XE/XF
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
Close to
Vaddis
2
C_B_U
C_B_U
VDD DAC
Y_R_V
CVBS_C
Y_R_V
CVBS_C
VDD DAC
CVBS_G_Y
OSCIN
OSCOUT
VDDPLL
CVBS_G_Y
RESET#
OSCOUT
IR RCV
DU PRD0/FPC_DOUT
S/PDIF_OUT
S/PDIF_OUT
VDDAPWM
GP-0
GP-1
R30
100
C31
33pF
IR RCV
FPC_DOUT
APWM_LAPWM_R-
C32
0.1uF
Crystal
Y2
27.000MHz
R28
220K
GP-4
GP-5
OSCIN
C33
33pF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
0.1U
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
1%
1%
1%
1%
M5V
MUTE_CTL
SFCS_0
S FCS
MBRX120
2USB5V
RAMADD[0]
RAMADD[8]
RAMADD[10]
VDDP
RAMADD[9]
RAMADD[11]/GPO[64]
RAMCS0#
RAMBA
RAMCS1#/GPO[65]
RAMRAS#
RAMCAS#
VDDP
RAMWE#
RAMDQM
GNDPCLK
PCLK
VDDPCLK
RAMDAT[8]
RAMDAT[7]
RAMDAT[9]
RAMDAT[6]
RAMDAT[10]
RAMDAT[5]
RAMDAT[11]
RAMDAT[4]
RAMDAT[12]
RAMDAT[3]
VDDIP
RAMDAT[13]
RAMDAT[2]
VDDC
RAMDAT[14]
RAMDAT[1]
RAMDAT[15]
RAMDAT[0]
VDDP
GNDAPWM
VDDAPWM
D1
1
75R
75R
75R
75R
U2A
R22
4.7K
MUTE_CTL
R106
RF
C82
NC
2
4PIN/2.0mm
RF
C24
33pF
C9
DSPVCC33
4
3
2
1
1nF
DSPVCC18
DSPVCC33I
4.7K
SFCLK
SFDO
SPI FLASH-SOP8
Atmel: AT26DF081A
F1
C23
1
R24
R25
R26
R27
4.7K
/CS
VDD
SO /HOLD
/WP
SCK
GND
SI
1nF
C21
0.1U
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
R20
1
2
3
4
C22
DSPVCC33
500
C20
10nF
Gen_5/GPIO[0]
Gen_6
VDDP
Gen_7
Gen_8
Gen_9
Gen_11
Gen_12/VID0
VDDC
GPIO[52]/PWMCO[3]/HSYNC
GPIO[51]/PWMCO[2]/FIELD
GPIO[50]/PWMCO[1]/VCLKx2
VDDPWM
GPIO[49]/PWMCO[0]
DVD_LD
CD_LD
DVD_MD
CD_MD
VDDSAFE
GNDREF
RESOUT
VREF
VC
GND1AFE
VFE_YIN
F
K
E
J
D
C
VDDAFE
B
A
VDD1AFE
RFN
RFP
GNDDACBS2
S FCS
SF DI
VDDAFE
DSPVCC33
U1
DSPVCC33
FOCUS_PWM
LD_DVD
LD _CD
MD_DVD
MD_CD
C28
1nF
SLED_PWM
SPDL_PWM
TRACK_PWM
CD_DVD
CLOSE
HOMESW
CD_DVD
VDDPWM
FPC_STB
FPC_CLK
OPEN
DRVSB
CD_DVD_1
FPC_STB
FPC_STB
DUPTD0/FPC_CLK FPC_CLK
SPDL_PWM
SLED_PWM
1K
VDDAFE
Close to Vaddis!
FOCUS_PWM
TRACK_PWM
1K
DSPVCC33
Q14
1
R17
4.7
+ CE2
100U/16V
RESET#
Q13
+
R16
R14
R100 1k
R101 3.3k
2N3904
INSW
1MA
VDDPWM
D8
1N4148
R99
22k
R102
4.7k
IN_OUT_SW
E
RAMDAT14
RAMDAT1
RAMDAT15
RAMDAT0
RAMDAT13
RAMDAT2
RAMDAT8
RAMDAT7
RAMDAT9
RAMDAT6
RAMDAT10
RAMDAT5
RAMDAT11
RAMDAT4
RAMDAT12
RAMDAT3
IPCLK
RAMRASRAMCAS-
RAMWERAMDQM
Net has fewer than two connections N21830557:
C38
0.1U
C39
0.1U
C40
0.1U
C44
0.1U
RAMDQM
PCLK
RAMCKE
RAMDAT8
RAMDAT10
RAMDAT9
RAMDAT12
RAMDAT11
RAMDAT14
RAMDAT13
RAMDAT15
RAMDAT14
RAMDAT15
RAMDAT12
RAMDAT13
RAMDAT10
RAMDAT11
Download & debug
APWM_LAPWM_R-
(165.10, 185.42)
Down load
Close to pin 38
VSYNC_VGA
HSYNC_VGA
DSPVCC33
GP-5
GP-4
‫ݐ‬ᆍ64Msdram ᴧ
2ch internal Audio output
VGA support
internal KOK support
XP6
4PIN/2.0mm
1
2
3
4
DUPTD1
DUPRD1
GP-0
GP-1
AMCLK
AOUT0
GP-4
GP-5
ALRCLK
ABCLK
Hyper Terminal
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
VSS
NC
DQMH
CLK
CKE
NC
A11
A9
A8
A7
A6
A5
A4
VSS
External 2ch Audio DAC amd ADC
[64Mbit:K4S641632H-UC70]
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
4
DUPTD0
DUPRD0
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
VDD
DQML
WE#
CAS#
RAS#
CS#
BA0
BA1
A10
A0
A1
A2
A3
VDD
C43
0.1U
1
2
3
4
4
A
B
RAMDQM
RAMWERAMCASRAMRASRAMCS1RAMBA
RAMCS0RAMADD10
RAMADD0
RAMADD1
RAMADD2
RAMADD3
R33
10K
RAMCKE
RAMDAT7
RAMDAT5
RAMDAT6
RAMDAT3
RAMDAT4
RAMDAT1
RAMDAT2
C49
0.1U
RAMDAT0
C48
0.1U
RAMDAT1
RAMDAT0
C47
0.1U
RAMDAT3
RAMDAT2
C46
0.1U
RAMDAT5
RAMDAT4
C45
0.1U
RAMDAT7
RAMDAT6
DSPVCC33I
C84
0.1U
RAMADD3
RAMADD2
RAMADD1
RAMADD0
RAMADD10
RAMBA
RAMCS0RAMRASRAMCASRAMWERAMDQM
DSPVCC33
C83
0.1U
3
DUPRD1
DUPTD1
DUPRD0
DUPTD0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
C42
0.1U
SCHEMATIC1, 3.Vaddis_SDRAM_Flash
GP-4
GP-5
DU PRD0/FPC_DOUT
DUPTD0/FPC_CLK
XP5
4PIN/2.0mm
DUPTD0/FPC_CLK
DU PRD0/FPC_DOUT
NM
U10
16Mbit: K4S161622C-TC/L70
VDD
A3
A2
A1
A0
A10/AP
BA
CS
RAS
CAS
WE
LDQM
VDDQ
DQ7
DQ6
VSSQ
DQ5
DQ4
VDDQ
DQ3
DQ2
VSSQ
DQ1
DQ0
VDD
C41
0.1U
U3
DSPVCC33
VSS
A4
A5
A6
A7
A8
A9
NC
CKE
CLK
UDQM
NC
VDDQ
DQ8
DQ9
VSSQ
DQ10
DQ11
VDDQ
DQ12
DQ13
VSSQ
DQ14
DQ15
VSS
L10
500
SDRAM3V3
10R
CE4
470uF/6.3V
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
C37
0.1U
SDRAM3V3
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
C36
0.1U
RAMDAT8
RAMDAT9
RAMADD4
RAMADD5
RAMADD6
RAMADD7
RAMADD8
RAMADD9
DSPVCC18
RAMCKE
PCLK
RAMDQM
SFCLK
DSPVCC18
R32
DSPVCC33
XXmA
C35
0.1uF
Close to
Vaddis
Down load
DSPVCC33
+
RAMADD11
WARNING [DRC0006]
VDDAPWM
3.30V
RAMADD9
RAMADD8
RAMADD7
RAMADD6
RAMADD5
RAMADD4
RAMADD11
down load
C34
5P
RAMCS1-
HYPER
1
.
PCLK
RAMCS0RAMBA
R31
56R
SF DI
TP1
RAMADD0
RAMADD8
RAMADD10
R29
1K
[NM]
RAMADD9
IPCLK
DSPVCC33
3
SDRAM3V3
C
D
E
7-7
7-7
A
B
C
D
E
Main Board Electric Diagram for DVP3320: FE_Regulator
Close to CN201
DSPVCC33
C DLD
DV DLD
EMC
C50
NM
[470pF]
R34
4.7R
C51
NM
[470pF]
1
OPU
Sony310
DL3
IAT510
TOP1100S
SEMCO-SP1
MITSM820W
HD8(DV23)
HOP1200W
HD65/HD62
502W
Arima681
+ CE5
220uF/16V
Q4
9012
R36
220R
LD_DVD
DSPVCC33
OPU
R34:
R38:
HD65PS
3.3R
3.3R
Others
4.7R
4.7R
CN201 is used for Sanyo/Samsung/Sony OPUs
R38
4.7R
25
26
XP7
SMD0.5 TOP
C52
1nF
TOP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
C53
1nF
+ CE6
220uF/16V
Q5
9012
DV DLD
R42
220R
R43
LD_CD
OPU
HOP1200W
Arima681
Others
R202=300R, for HOP1200W only
BEMF
Current Type(Default)
R40
100R
0
100R
10R
0
91R
0
NM
0
91R
NM
R270
100R
100R
NM
R35
2K
SP_M-
SPDL_SENS-
SPDL_SENS-
D5
1
2
DSPVCC33
R37
1R 0603-R
3
1
MD_DVD
R39
100R
[NM]
R283
100R
100R
NM
VR _CD
MD_CD
R41
BAT54C
2K
SP_MOT-
R40
100R
[NM]
SPDL_SENS+
SPDL_SENS+
VR_DVD
0R [300R]
OPU_HFM
RFA5V
C DLD
VR_DVD
VR _CD
OPU5V
VC1
R39
100R
0
100R
10R
0
91R
0
NM
0
91R
NM
C54
1nF
+
CE7
100uF/16V
L11
R44
10uH
33R
RF_E
2.1V
RFA5V
U4
VC
R45
3.3K
R F_F
RF_B
RF_A
RF
PDIC Control:
DVD=LOW
CD=HIGH
CD_DVD
1
VINFC
MUTE
28
TR_B1
2
TR_B1
BIAS
27
REGO2
CD_DVD
R F_D
R F_C
TACTTACT+
FACT+
FACT-
SLED_S
REGO1
3
REGO2
VINTK
26
4
VINSL
TR_B2
25
5
REGO1
NC
24
6
FWD
VINLD
23
7
REV
GND
22
29
GND
GND
30
8
VCC1
VCTL
21
OPEN
2
AM5888S(HSOP-28)
FOCUS_S
C55
100pF
TR_B2
R46
1K
SPDL_S
2
27
28
CLOSE
DRVSB
VC2
TRACK_S
C56
0.1uF
C57
0.1uF
+ CE8
47uF/16V
M5V
CE9
100uF/16V
LOAD-
C58
0.1uF
SLEDSLED+
HOMESW
GND
SP+
SP-
6
5
4
3
2
1
M5V
VOTR-
NC
20
10
VOTR+
VCC2
19
SL_MOT- 11
VOSL+
VOLD-
18
SP_M-
SL_MOT+
SL_MOTHOMESW
SL_MOT+12
VOSL-
VOLD+
17
SP_MOT+
FACT-
13
VOFC-
VOTK-
16
TACT-
SP_MOT+
SP_MOT-
FACT+
14
VOTK+
15
TACT+
LOAD+
XP8
6PIN/2.0mm
9
VOFC+
Close to Vaddis!
FOCUS_S
TRACK_S
R47
R48
51K [27K]
51K [27K]
SPDL_S
SLED_S
R49
R50
22K [22K]
51K [33K]
C59
C60
C61
C62
1nF
1nF
27nF
27nF
FOCUS_PWM
TRACK_PWM
SPDL_PWM
SLED_PWM
M5V
DSPVCC33
XP9
5PIN/2.0mm
Imax=600mA
Õǂ?540mA
R51
2.2 OHM 2W
R52
4.7K
HOMESW
IN_OUT_SW
INSW
Imax=300mA
Õǂ?I=290mA
HOMESW
IN_OUT_SW
INSW
5.6 OHM 1W
3
C63
NM
[1nF]
C64
NM
[1nF]
R53
Imax=300mA
Õǂ?250mA
C65
NM
[1nF]
DSPVCC18
DSPVCC33
TR_B1
TR_B2
Q6
SS8550D
SS8550D
C66
+
0.1uF
DSPVCC33
b
Q7
R56
CE10
220uF/16v
20k/1%
R57
R54
1K 1%
CE11
+
REGO2
R59
R55
33K
VC2
R58
1K 1%
4.7K/1%
REGO1
3
Close to motor driver.
e
1
2
3
4
5
c
LOADLOAD+
OUTSW
GND
INSW
LOADLOAD+
220uF/16v
R60
C67
0.1uF
GND
10k/1% GND
12k/1%
GND
GND
4
4
A
B
C
D
E
7-8
7-8
A
B
C
D
E
Main Board Electric Diagram for DVP3320: Audio Input Output
M5V
Q8
R61
82K
R63
4.7K
9012
39K
APWM_L-
75pF
4
C69
1.2nF
6
OP+
5
C70
0.1uF
R68
R69
3.3K
4.7K
Q10
470
R66
10K
MUTE
LMAIN_OUT
1
Q9
3904
R67
R70
82K
470
R72
4.7K
39K
C71
75pF
4
C72
1.2nF
2
4.7K
CE16
10uF/16V
R74
1
+12VA
R75
10K
MUTE
C73
0.1uF
Q12
2N3904
470
RMAIN_OUT
+
3
8
OP+
+
+6VA
U5A
LM4558
-
OP-
R73
4.7K
R77
R65
+
R71
MUTE_CTL
10uF/16V
9012
CE14
APWM_R-
MUTE_CTL
CE13
MUTE
220U/16V
2
U5B
LM4558
7
8
+6VA
OP-
+
1
-
R64
4.7K
C68
+
R62
Q11
3904
R76
470
2
R78
22K
DSPVCC33
+6VA
VFE_YIN
R96
VFE_YIN
R103
4.7K/NC
C74
1k
1uF/NC
XP10
R81
0R
MIC
+6VA
1
2
3
+12VA
R79
100K
+12VA
R80
+
CE20
C77
C76
3300p
100p
0.1uF
10uF/16V
+12V
+12V
+
+ CE17
CE18
47uF/16V
33K
100U/16V
C75
100R
R82
pitch=2.0mm*3
3
THE OK USE C74 or CE20
R108
4.7K/NC
2
BAT54S/NC
1
3
D7
3
DSPVCC33
P2
RCA/AUDIO OUT
C78
COAX_SPDIF
100
R84
1
2
3
4
5
6
LMAIN_OUT
RMAIN_OUT
COAX_SPDIF
0.1uF
100
RCA
47-RCA151-XX1
R83
S/PDIF_OUT
C79
C80
100pF
C81
100pF
100pF
4
4
A
B
C
D
E
7-9
Front Board & Switch Board Print-layout (Bottom side):
7-9
7-10
7-10
OK Board Print-layout (Top side):
OK Board Print-layout (Bottom side):
7-11
Power Board Print-layout (Bottom side):
7-11
7-12
7-12
Main Board Print-layout (Top side):
7-13
7-13
Main Board Print-layout (Bottom side):
8-1
Exploded View for DVP3320/55:
12
13
11
10
8
9
7
6
5
4
3
14
15
16
17
2
18
1
20
21
19
It's a general mechanical view for DVP3320/55, pls refer to the model set
for detailed information.
Assy 1 component includes:1.3.4.5.21
8-2
DVP3320/55 SERVICE PARTLIST
MECHANICAL PARTLIST
ELECTRICAL PARTLIST
No
12NC No.
Description
9
996510022398
ASSY-MAIN BD
16
996510022397
ASSY-PW BD
20
996510020922
ASSY-FB BD
6
996510020934
ASSY-SW BD
19
996510022401
ASSY-US BD
10
996510021457
LOADER
OPU
996510021449
SANYO LOADER (DV38)
Q'ty
No
12NC No.
1
1
1
1
1
1
1
11
996510022399
TOP COVER
13A
996510020885
POWER SOCKET TRANSITION
ASSY-MAIN BD COMPONENT PARTLIST
Description
Q'ty
Description
Q'ty
13B
996510001175
POWER CORD
15
996510022429
BACK PANEL
17
996510006463
PAD
2
996510022395
FRONT DOOR
1
1
1
1
4
1
8
996510020928
BOTTOM PLATE
1
AVCABLE
996510001106
VIDEO CABLE 1500MM
1
Assy1
996510022396
ASSY - FRONT DOOR
1
CON2
996510010962
5PIN CBL TJC3-5Y/SCN-5P L=90MM
1
No
12NC No.
D1
996510022393
SMD. DIODE MBRX140
1
RC
996510020682
REMOTE CONTROL
1
D10
996510020926
IC PESD5V0S1BA
1
XP11
996510022394
4PIN CABLE WITH SHIELD L=180MM
1
D11
996510020926
IC PESD5V0S1BA
1
XP7
996510001168
24PIN HS
1
D12
996510020926
IC PESD5V0S1BA
1
XP8
996510021448
6PIN HS
1
D5
996510009668
BAT54C
1
XP9
996510004063
CABLE PH-5Y/PH-5Y L=130MM
1
D8
996510009667
SMD. SWITCHING DIODE LL4148
1
XS301
996510012698
HS 6P PH-6Y/JC20-6Y 150MM
1
D9
996510020926
IC PESD5V0S1BA
1
Q10
996510009670
TRANSISTOR SMT 3CG9012M
1
SCREWS LIST:
Q11
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
No
Q12
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
7
—
S/T SCREW B 2.6 X 8 BF
6
Q13
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
12
—
S/T SCREW B3 X 6 BF
9
Q14
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
14
—
S/T SCREW B 3 X 7 BF
5
Q2
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
Q3
996510009671
PNP TRANSISTOR
1
Q4
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
Q5
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
Q6
996510009671
PNP TRANSISTOR
1
Q7
996510009671
PNP TRANSISTOR
1
Q8
996510009670
TRANSISTOR SMT 3CG9012M
1
Q9
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
U1
996510020916
16M SPI FLASH EON
1
U10
996510021455
64M SDRAM -6NS TSP54
1
U2
996510021459
IC ZR36966PQCG-XE2
1
U4
996510011055
IC CD5888CB
1
U5
996510010924
DUAL OPERATIONAL AMPLIFIER
1
Y2
996510009675
27MCL20PF
1
ASSY-PW BD COMPONENT PARTLIST
No
12NC No.
D1
996510011047
Description
DIODE IN4007
Q'ty
1
D10
996500027866
DIODE SR360 3A/60V
1
D2
996510011047
DIODE IN4007
1
D3
996510011047
DIODE IN4007
1
D4
996510011047
DIODE IN4007
1
D7
996500014043
DIODE FR102 (FAST RECOVERY)
1
D8
996510011047
DIODE IN4007
1
L1
996510009942
COIL WIDTH
1
L2
996500032509
COIL SL0811-6R8K2R4
1
T1
996510010954
TRANSFORMER CONV
1
U1
996510010953
IC TNY176PN
1
U2
996500027867
PHOTOCOUPLER PS2561L1-1-V(WF)
1
U3
996500014609
IC AM431LP
1
ASSY-FB BD COMPONENT PARTLIST
No
12NC No.
Description
Q'ty
LED1
996510020917
J2808AG
1
REM301
996510020925
HM338-12 RECEIVER MOD H=12MM
1
U301
996510009665
IC ET6202 SOP-2
1
12NC No.
Description
Q'ty
9-1
REVISION LIST
Version 1.0
* Initial release for DVP3320/55