Download Olympus CAMEDIA E-100RS Quick Start Guide
Transcript
䢇 Quick-Start Guide 䢇 http://www.olympus.com Thank you for purchasing the Olympus E-100RS. This Quick-Start Guide has been designed for those who want to become familiar with the E-100RS in a very short time. The “Names of parts” section is especially helpful for identifying parts easily without having to read through the complete Instruction manual. For detailed operations, please refer to the complete Instruction manual. Names of parts Setting the date/time Self-timer lamp/AF assist lamp Control panel (See the other side for details.) 1. Set the Mode dial to P. Mode dial Diopter adjustment dial 5-pin external flash socket Shutter button 1 Getting Ready... Zoom lever/Indexdisplay lever Microphone Loading the batteries Remote cable jack 1. Follow the procedure below. Open the battery compartment cover. Lens Load the batteries. AA batteries (provided) Lithium battery packs Close the battery compartment cover. 2 2. Press (Menu button). The Menu appears on the screen. Press (Monitor buton) to select whether to display the menu on the Monitor or the Viewfinder. 3. Press on the Arrow pad to move the green frame in the Menu, then select “MODE SETUP”. Remote control receiver Slide the battery compartment lock toward . OLYMPUS AMERICA INC. Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000 (Customer support) Tel. 1-888-553-4448 USB connector Slide the battery compartment lock toward . DC-IN jack External microphone jack Strap eyelet “SETUP” appears on the screen. The selected item appears in green. 4. Press OK. The MODE SETUP screen appears. P F2.8 1/800 0.0 Flash (built-in) A/V OUT jack SM MODE SETUP CF ISO PRE-CAPTURE 2 WB [SM] Connector cover [1/5] [SM] Lens cap 5. Press 多 Close the battery compartment cover while pressing the batteries with the cover. 多 Manganese batteries cannot be used. Flash mode button 640 x 480 OFF [1/3] [SM] Menu screen 5/5 , then press /Erase button MODE SETUP screen 1/3 . SHOT CANCEL Metering mode button Macro button For CompactFlash 1360x1024 SQ [5/5] DRIVE button Open the Card cover and push in the card* as shown below. (*The pictures you take will be stored in the card.) NORMAL TIFF OK “SETUP” appears on the screen. To go to the previous page, move the cursor to the top item and press the on the Arrow pad. 2. Inserting a SmartMedia or CompactFlash card. * Before inserting, check that the Power switch is off and there are no images on the Viewfinder/Monitor. * To choose SmartMedia or CompactFlash, select one (SM/CF) on the menu or simply insert a Card into the camera. to select ON SETUP S-Prg Menu screen 1/5 For SmartMedia 0.0 ALL RESET SM/CF 1 1 P F2.8 1/800 Flash switch m/ft INFO button [SM] OFF button SHOT CANCEL 12.23.’00 12:34 m SETUP m/ft [3/3] [SM] [3/3] MODE SETUP screen 3/3 Viewfinder 6. Press OK. Open the Card cover. Push the Card in and close the Card cover. Tab Push the Card in. Tab The Date/time setting screen appears. When the tab pops out, pull it down as shown, then close the Card cover. 3. Turn on the camera. Power switch (POWER OFF/ON/RESET) Arrow pad Set the Power switch to ON. Power switch AE lock button (AEL)/ Multi-metering button/Print button OK button/ Manual focus button (MF)/ Protect button Date/time setting screen 7. Press Monitor Tripod socket / on the Arrow pad to select the date order. (Date order selections: date/month/year, month/date/year, year/month/date) Monitor button You can select camera functions using the Mode dial. You will probably want to try the Program mode first, which lets you take properly-exposed pictures by simply pressing the Shutter button. Mode dial E DIA L S-Prg M S A P MO D [Still picture shooting mode] P: Simply press the Shutter button to take a picture. A: Set the desired aperture manually. S: Set the desired shutter speed manually. M: Set the desired aperture and shutter speed manually. S-Prog: Take pictures under a variety of conditions. (Portrait/ Sports/Landscape/Night Scene) [Movie record mode] : Records movies. Menu button 8. Press Card cover , then press / to adjust the date/time. Speaker Card access lamp To go to the next setting (i.e. month to year, etc.), press previous setting (i.e. year to month, etc.), press . Battery compartment cover . To go back to the Battery compartment lock Adjusting the Diopter Turn the Diopter adjustment dial until you see the AF target mark clearly in the Viewfinder. Diopter adjustment dial Viewfinder P F2.8 1/30 9. Press OK when you complete your settings. 0.0 10. To cancel the Menu, press OK until the Menu disappears. [SM] [Playback mode] : Plays back your recording. AF target mark 1AG6P1P0845– – VT1579-01 䢇 Quick-Start Guide 䢇 http://www.olympus.com 2 Flash intensity control Card error Slow shutter synchronization flash Card writing Taking still pictures Flash mode 1. Set the Mode dial to P. Macro mode Full-time AF Sound record Auto bracket Prg M S A P P F2.8 1/30 Exposure compensation 0.0 Self-timer/ Remote control ISO Manual focus AF target mark Number of storable still pictures Metering mode Stabilizer [To enlarge your subject] Press the Zoom lever toward “T” to enlarge your subject. To return to normal magnification, press the Zoom lever back toward “W”. AE memory Record mode Press fully 3 AF confirmation mark 0.0 Erasing pictures Playing back pictures . OK NO Confirmation screen [SM] CARD SETUP YES MODE SETUP NO 12.23.,00 21:56 [SM] 10 [SM] Still picture display (1-frame) [2/2] Erasing a still picture YES OK NO Confirmation screen 0.0 Arrow pad Memory gauge * Press the Zoom lever toward “W” to display multiple pictures at the same time (Index-display). * Press the Zoom lever toward “T” to display a close-up. 1234 1235 1236 1237 1238 1239 1240 1241 1242 Index-display [Movie pictures] Card access lamp (1) (2) (3) . 2. Press the Shutter button fully to start movie recording and press it again fully to stop. [SM] HQ [SM] The maximum available recording time appears on the Viewfinder. NO x10 ● Use the Arrow pad to select the desired picture for playback. : Plays back next picture. : Plays back preceding picture. : Jumps to the picture 10 frames ahead. : Jumps to the picture 10 frames behind. 4. Press the Shutter button fully to take a picture. Taking movie pictures YES Press , then select “CARD SETUP”—“ ” using the Arrow pad. Press OK. Select “YES” on the confirmation screen, then press OK again. (To cancel, select “NO”, then press OK.) The last picture taken is played back. P F2.8 1/30 Unwanted images can be erased. You can erase one frame or all frames, depending on your requirements. To erase an unwanted image, first display it on the screen as described in “ 3 Playing back pictures” on this page. All-frame erase Set the Mode dial to AF target mark 1. Set the Mode dial to 4 YES [SM] The free part of the memory gauge lights up and the card access lamp blinks while the picture is being recorded. Continuous shooting is available even if the card access lamp is blinking, unless the entire memory gauge is lit. If you are taking a picture in a dark environment, the built-in flash will fire automatically if it has been popped up. [1/2] [SM] Press (Erase button) on the camera and select “YES” on the confirmation screen using the Arrow pad. Then, press OK. Card Sequential shooting P F2.8 1/30 COPY 1-frame erase Seconds that movies can be shot Pre-capture 3. Press the Shutter button halfway to focus. Press halfway START AF system [SM] Press (Monitor button) to select whether to display your image on the Monitor or the Viewfinder. SM/CF MOVIE PLAY Battery check White balance Viewfinder The AF confirmation mark lights up in green in the upper left corner and the camera beeps. Focus and exposure (shutter speed/aperture) become locked. If the AF confirmation mark blinks, then the camera is out of focus. If this happens, release the Shutter button and move the AF target mark slightly. Then, press the shutter button halfway again. ● Use the Arrow pad to select the desired picture for playback. : Plays back movie pictures when held down continuously. : Plays back movie pictures in reverse when held down continuously. : Jumps to the beginning of the movie. : Jumps to the end of the movie. ● Press OK to pause the movie. Control panel indications Taking pictures 2. Compose the picture by turning the camera towards the subject and centering the AF target mark on the image you want to shoot. OLYMPUS AMERICA INC. Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000 (Customer support) Tel. 1-888-553-4448 (4) will appear with pictures that can be played back as movies. Press (Menu button) to display the Menu. Select “MOVIE PLAY” and press on the Arrow pad. When “START” appears, press the OK button. The card access lamp blinks for a moment, then the movie starts. Press when you are finished watching. The Menu reappears. Press exit the Menu. 5 Turning off the power When you are finished using the camera, turn the power off after checking that the card access lamp is not on. ● The picture on the screen will disappear when you turn the power off. ● If no operation is performed for 1 minute or more, the image on the screen goes off automatically to avoid battery exhaustion (this function is called Sleep). To end Sleep, perform any operation on your camera. ● When you store the camera, make sure to put the lens cap on. again to The card access lamp blinks while the picture is being recorded. Continuous shooting is available when the card access lamp stops blinking. Printed in Japan