Download Metra Electronics 95-8210 User's Manual

INSTALLATION INSTRUCTIONS FOR PART 95-8210
APPLICATIONS
Toyota 4-Runner Limited
2003-2009
95-8210
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double Din Trim Plate • B) Double DIN Brackets
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-1761 - Toyota harness 1987-up
• TYTO-01 - Toyota amp harness 2003-UP
Antenna Adapter:
• Not required
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932
www.metraonline.com
© COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION
95-8210
TABLE OF CONTENTS
Dash Disassembly
- Toyota 4-Runner Limited 2003-2009 . . . . . . . . . . . . . . . . . 1,2
Kit Assembly
- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
*Note:
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take
steps toward a better tomorrow.
95-8210 DASH DISASSEMBLY
Toyota 4-Runner Limited 2003-2009
A
1 Disconnect the negative battery terminal to prevent an accidental short
circuit.
2 Unsnap and remove trim from around
shifter. (Figure A)
3 Unsnap and remove center console
cover. (Figure B)
B
4 Unsnap trim ring from around ignition
key cylinder.
5 Remove (1) 10 mm bolt from bottom
right side of panel below steering column. Unsnap panel and pull away to
gain access behind panel. (Figure C)
C
6 Remove (1) 10 mm bolt on bottom left
of center panel behind panel below
steering column. ( (Figure D)
D
1
95-8210 DASH DISASSEMBLY
Toyota 4-Runner Limited 2003-2009
E
7 Remove (1) 10 mm bolt beneath climate control behind pocket door.
(Figure E) Unsnap climate control,
unplug and remove climate control.
(Figure F)
8 Remove (2) 10 mm bolts beneath
radio behind climate controls.
(Figure G)
F
9 Unsnap and remove entire center
panel around radio.
10 Remove (2) 10 mm bolts securing
radio. Unplug and remove radio.
(Figure H)
PASS
Continue to final assembly.
G
H
2
R
ENGE
95-8210 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1 Snap the factory brackets to the side
of the radio. (Figure A)
2 Snap the Double DIN brackets to the
outside edge of the Double DIN trim
plate. (Figure B)
3 Slide the Double DIN radio into the
bracket/trim plate assembly and
secure the radio to the assembly
using the screws supplied with the
radio. (Figure C)
B
Continue to final assembly.
C
3
95-8210 KIT ASSEMBLY
STACKED ISO UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1 Snap the factory brackets to the side
of the radio. (Figure A)
2 Snap the Double DIN brackets to the
outside edge of the Double DIN trim
plate. (Figure B)
3 Slide the stacked ISO mount units into
the bracket/trim plate assembly and
secure the units to the assembly
using the screws supplied with the
units. (Figure C)
B
Continue to final assembly.
C
4
95-8210 FINAL ASSEMBLY
FINAL ASSEMBLY
A
(A) Strip wire ends back 1/2"
B
B) Twist ends together
C) Solder
D) Tape
C
D
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Right Front (-). . . . . . . . . . . . . Gray/ Black
Ground. . . . . . . . . . . . . . . . . . Black*
Left Front (+) . . . . . . . . . . . . . White
Power Antenna. . . . . . . . . . . . Blue
Left Front (-). . . . . . . . . . . . . . White / Black
Amp Turn-On . . . . . . . . . . . . . Blue / White
Right Rear (+) . . . . . . . . . . . . Violet
Amp Ground. . . . . . . . . . . . . . Black / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Illumination . . . . . . . . . . . . . . Orange
Left Rear (+) . . . . . . . . . . . . . Green
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5
95-8210 INSTRUCTIONS
1-800-221-0932
www.metraonline.com
REV. 06/03/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST95-8210