Download Meade LX70 Operating Instructions

Operating Instructions
The Meade LX70 Polar Scope
For use with all LX70 Series Mounts
For most telescope observers casual polar alignment is all that is needed,
which will not require use of the polar finder. However, for those observers
who need to meet the more demanding requirements of astrophotography,
the polar scope allows the telescope mount to be more precisely aligned
with the celestial poles. The polar scope contains a reticle pattern which
is used in assisting the user in achieving a more accurate polar alignment.
Remove
Remove
Installing the Polar Scope:
1. Begin by removing the polar axis front and rear covers (see figure 1).
2. Remove the rear part of polar axis (see figure 2) by rotating it counterclockwise. This part will not be used.
3. Thread in the Meade LX70 polar scope until firmly seated. The polar
scope is now installed and should remain installed in the mount. When finished using the polar scope, replace the front and rear covers.
Figure 1: Remove polar covers
Figure 2: Remove rear part
Figure 3A: Position A
Figure 4A: Aligned when object stays
centered at position A & B
Figure 3B: Position B
Figure 4B: Misaligned when object
moves off center between position A/B
Before the polar scope can be properly used with any precision, it must first
be calibrated to the mount’s polar axis.
Aligning the Polar Scope to the Polar Axis:
1. Set the telescope mount & tripod up outside in the daytime with the optical tube, counterweight and counterweight shaft removed.
2. Unlock the DEC axis and rotate it to DEC 0. In this position, the optical
tube (if installed) would be at 90 degrees to the mount. With the DEC axis
in this position and polar scope covers removed, you can now view thru the
polar scope at a distant terrestrial target.
3. Look through the polar viewfinder and notice the reticle pattern (see
figure 6). Note, some reticle patterns may appear different but the alignment
procedure is identical. If the reticle is not in focus, rotate the focus ring (fig
5, #11) until the reticle pattern is sharp.
4. Adjust the mount and tripod so the polar axis is pointing at a distant
terrestrial object. The further the target, the more accurate the alignment.
1
5. Placing the reticle center cross hair over the target, unlock the RA and
rotate the RA axis 180 degrees, from one side of the mount to the other (see
figure 3A & 3B). Re-lock the RA axis.
2
If the polar scope is not aligned with the mount’s polar axis, the target will
move off center (see figure 4A & 4B) and the reticle adjustment screws (see
fig 5, #9) will need to be adjusted.
3A
3B
6. To adjust the polar scope so the target does not move off the reticle
cross hair, slightly loosen the reticle adjustment screw which is closest to
the cross hair and opposite of the movement. You then need to tighten the
adjustment screw on the side closest to the target. Notice that a small turn
of each screw will result in a large movement of the reticle. Only adjust the
screws to correct for half the movement off the cross hair at a time, moving
the target approximately halfway to the center of the reticle.
7
8
4
5
6
9
10
NOTE: The reticle adjustment screws work in a push-pull motion. When
loosening these screws, never loosen more than 1/8 of a turn at a time.
Doing so could cause the reticle to fall out. When one adjustment screw is
loosened, an adjustment screw on the opposite side should be tightened.
Do not over tighten or you may damage the reticle.
11
7. Next, unlock the RA axis and rotate this axis 180 degrees, back to the
starting point. Re-lock the RA axis. Repeat steps 4-7 until the target no longer moves off the reticle cross hair.
Figure 5: Polar Scope Dials
1. RA setting circle locking screw
2. RA setting circle indicator
3A. RA setting circle (Northern hemisphere users)
3B. RA setting circle (Southern hemisphere users)
4. Calendar-dial scale
8. The polar scope is now properly aligned with the mounts polar axis.
Calibrating the Dials and Indicators:
There are several additional parts on the mount and polar scope that need
to be calibrated; the RA setting circle(fig 5, #3), Calendar-dial scale(fig 5,
1
5. Longitude offset scale
6. Longitude-offset scale indicator
7. Longitude indicator locking set-screw
8. Assembly set screw (not used)
9. Reticle adjustment screws (3)
10. Polar scope
11. Focusing ring
#4), and Longitude-offset indicator (fig 5, #6). All are located adjacent
to the polar scope. For the part locations of these dials, see figure 5. To
calibrate the dials and indicators:
1. Unlock the RA setting circle locking screw(fig 5, #1) and position the
RA setting circle dial (fig 5, #3) until the 0 mark is aligned with the RA setting circle indicator (fig 5, #2). Re-tighten the locking screw.
2. Look through the polar scope and note the reticle cross-hair. Unlock
the RA axis and rotate the RA until “Polaris” is at the bottom of the polar
scope field of view as shown in figure 6. Re-lock the RA axis.
3. Now adjust the calendar dial (fig 5, #4) so the large line between the Figure 6: Polar scope reticle
10 & 11 is aligned with the mount RA indicator (see fig 7).
Figure 7: Calibrated dials
Note: The calendar dial is numbered 1-12 with the longest lines separating the months. The short lines are two days apart and medium sized
lines are ten days apart.
4. With the RA in this position, the Longitude-offset scale indicator (fig 5,
#6) needs to be aligned with the 0 mark on the Calendar-dial (fig 5, #4).
If it is not aligned with the calendar dial 0 mark, use a tiny flat head
screwdriver(user supplied) to loosen the Longitude indicator locking setscrew and align the marks. Tighten the screw when aligned. When com- Figure 8: Longitude-offset scale adjusted 2.18 degrees East for Irvine, CA.
plete the reference dials should appear as in figure 7.
The dials and reticle pattern are now adjusted for a specific calendar date
and time where Polaris is directly above the North Celestial Pole(NCP)
crossing the meridian. This occurs at midnight on November 1st. The “Polaris” mark in the reticle was placed at the bottom of the viewfinder field of
view since the polar scope image is inverted.
Time Zone
Reference Time Zone Meridian
Hawaiian
150° West
Alaskan
135° West
Pacific
120° West
Adjust for Site Longitude:
Mountain
105° West
Depending on your observing site longitude, you may need to further adCentral
90° West
just the Calendar-dial scale(see fig 5, #4) to compensate for your site
Eastern
75° West
longitude. First determine your observing site longitude by looking at a
map, GPS, or the internet. You will also need to determine the reference
Alantic
60° West
time zone meridian for your time zone. For observers in the USA, see
Figure 9: Reference time zone meridians for the USA
Figure 9. This can also be found using the internet. Once both values are
known, subtract your site longitude from the reference time zone meridian
to determine the longitudinal-offset needed.
4. Unlock the RA axis and rotate it so the current time on the RA setting circle
(fig 5, #3) is aligned with the current date on the calendar dial(fig 5, #4). Note
Reference Time Zone Meridian - Observing Site Longitude = Longitudinal-Offset
all times are in standard time and daylight saving times should not be used.
If the longitudinal-offset is a positive value, you’re East of the reference Lock the RA. Remember the top row of numbers on the RA setting circle are
meridian. If the longitudinal-offset is a negative value, you’re West of the for Northern Hemisphere users. The bottom row of numbers on the RA setting
circle are for Southern Hemisphere users.
reference meridian.
For example: The longitude in Irvine, California is 117.82° West. The 5. For Northern Hemisphere: Move the telescope mount using the azimuth
and latitude controls until Polaris (the North Star) is placed within the “Polaris”
reference time zone meridian for the Pacific Time zone is 120°.
reference circle on the reticle. If done correctly, the reference stars in the Big
Dipper and Cassiopeia should be in the same orientation as the markings in the
120° - 117.82° = 2.18° East
polar scope. The center cross hair denotes the location for the North Celestial
To compensate for this longitudinal-offset, the Calendar-dial scale(fig 5, Pole (NCP). It may be helpful to shine a red light over the front of the mount to
#4) will be adjusted. Note each line on the longitude-offset scale is 5° illuminate the reticle.
apart. Therefore, the longitudinal-offset scale should be adjusted to 2.2°
East, between the 0 mark and first line left of the 0 mark (see figure 8). 6. For Southern Hemisphere: Move the telescope mount using the azimuth
Do not change this longitudinal-offset unless your observing sites differ and latitude controls until the four-sided figure labeled “Octans” in the reticle are
superimposed on the four star group in the southern night sky. The grouping of
significantly in longitude.
four stars in Octans (Sigma, Tau, Chi, and Upsilon) are the closest reference
objects near the South Celestial Pole (SCP) and are often used in obtaining a
Using the Polar Scope:
Now that the polar scope is aligned to the polar axis and dial indicators precise polar alignment. It may be helpful to shine a red light over the front of
properly calibrated, the polar scope is ready for use in obtaining a precise the mount to illuminate the reticle.
polar alignment.
Note: Not all pointing positions are possible with the polar alignment reticle, as
the tripod is a limiting factor as to how far the optical tube and mount can be
1. At night, fully assemble your LX70 and point it to True North.
moved.
2. Remove both polar scope front and rear covers. See figure 1.
7. Once the celestial pole is centered, tighten the latitude and azimuth adjust3. Rotate DEC to 0 (perpendicular to the mount) so you can view through ment knobs. The mount is now precisely aligned on the night sky. Remember
to replace the polar scope covers to protect the polar scope.
the polar axis.
© 2015 Meade Instruments Corp. reserves the right to change product specifications or to discontinue proudct without notice.
14-9282-00 Rev 0
2
27 Hubble, Irvine, California 92618
(800) 626-3233 www.meade.com