Download Lightolier FAEM3 User's Manual

INSTRUCTION SHEET NO.
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
IS:FAEM3
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
C0506
Page 2 of 4
Retain these instructions for maintenance reference.
NEW INSTALLATION
A. INSTALLING EMERGENCY BALLAST TO STANDARD FRAME-IN KIT (Fig. 1 and 8).
1. Before placing FRAME-IN KIT in the ceiling, install EMERGENCY BALLAST to the center
of MOUNTING FRAME BRACKET as shown.
2. Tighten SCREW to secure two units together.
3. Remove JUNCTION BOX COVER and appropriate J-Box K.O., then attach
EMERGENCY BALLAST BX CONNECTOR.
WIRING - Read and understand all instructions before proceeding.
• Make sure AC power is off at the fuse box.
• Regular ballast and emergency ballast must be fed from the same branch circuit.
• Be sure all electrical connections are made and junction box is closed before
connecting inverter connectors in switch/indicator light box.
• In switched fixtures, emergency ballast must be connected ahead of any local switching.
• Emergency ballast is shipped from the factory ready for 120V or 277V supply connection.
Line Voltage selecton is made at switch box. For 120V, remove wire nut from 120V
lead (black) and connect to black lead of test switch, then cap the 277V lead (orange).
B. INSTRUCTIONS FOR WIRING EMERGENCY BALLAST FOR (1)
OR (2) 4-PIN LAMPS ELECTRONIC A.C. BALLAST FRAME-IN KIT
1. Before converting to emergency lighting, please identify no. of lamps and wattage of
frame-in kit, then select appropriate Wiring Diagram A, B or C for rewiring. There is a
requirement to remove lamp leads from A.C. ballast, and reconnect to emergency ballast.
2. Disconnect either BLUE LAMP LEAD from BALLAST by inserting conductor of RED JUMPER
(provided) into open terminal of QUICK CONNECTOR of BALLAST as shown in Fig. 2.
Gently pull BLUE LAMP LEAD out. Then remove RED JUMPER for later use.
3. Repeat step 2 (above) to remove other BLUE LAMP LEAD, and one appropriate RED OR
YELLOW LAMP LEAD from BALLAST (Fig. 2) and wiring diagrams.
4. Insert appropriate RED OR YELLOW JUMPER into the terminal where the RED
OR YELLOW LAMP LEAD was previously removed from QUICK CONNECTOR (Fig. 3).
5. Follow WIRING DIAGRAM A, or B, or C to complete the wiring at FLEX “A”.
Fig. 1
EMERGENCY
BALLAST
FRAME-IN KIT
BX
CONNECTOR
MOUNTING
FRAME
BRACKET
SWITCH/
INDICATOR
BRACKET
J-BOX
COVER
SOCKET
CUP
SCREW
Fig. 2
BLUE LAMP
LEADS
INSERT
RED
JUMPER
RED LAMP
LEADS
QUICK
CONNECTOR
Fig. 3
RED
JUMPER
INSERT
QUICK
CONNECTOR
WIRING DIAGRAM A (1-LAMP FIXTURE)
(1 LAMP EMERGENCY)
WIRING DIAGRAM B (2-LAMP FIXTURE) UP TO 2-42W
(1 LAMP EMERGENCY)
NOTE: FOR UNSWITCHED CIRCUIT, CONNECT
BOTH WHITE/RED AND ORANGE/BLACK LEADS
IN JUNCTION BOX TO UNSWITHCHED 120V
OR 277V. VOLTAGE SELECTION IS MADE IN
SWITCH BOX.
NOTE: FOR UNSWITCHED CIRCUIT, CONNECT
BOTH WHITE/RED AND ORANGE/BLACK LEADS
IN JUNCTION BOX TO UNSWITHCHED 120V
OR 277V. VOLTAGE SELECTION IS MADE IN
SWITCH BOX.
UNSWITCHED
120V OR COMMON
277V
(NETURAL)
For dimming ballast, connect
dimming leads to dimmer
BLK 120V
WHITE
RED
INVERTER
CONNECTOR
EMERGENCY
BALLAST
TEST
SWITCH
FLEX
"B"
FLEX
"A"
WHITE
ORG / BLK
ORG/BLK
W G
RED
ELECTRONIC
A.C. BALLAST
WHT/BLK
WHT / RED
ORG 277V
BLACK
B
INVERTER
CONNECTOR
BLUE/WHT
EMERGENCY
BALLAST
FLEX
"B"
FLEX
"A"
RED
WHITE
Y Y R R
B
YEL
B
SWITCH BOX
RED
B Y Y R R
BLUE
JUNCTION
BOX
BLUE / WHT
RED
RED**
BLUE**
YELLOW*
YELLOW
STAB-IN CONNECTOR (2 CONDUCTORS)
RED
STAB-IN CONNECTOR (3 CONDUCTORS)
STAB-IN CONNECTOR (3 CONDUCTORS)
LAMPHOLDER
RED
LAMPHOLDER 1
(EMERGENCY)
RED
YEL**
YEL
BLUE**
* WHITE AND YELLOW JUMPERS PROVIDED
** (2) BLUE AND (1) RED LEADS REMOVED
FROM ELECTRONIC BALLAST
RED
BLUE**
* WHITE AND RED JUMPERS PROVIDED
** (2) BLUE AND (1) RED LEADS REMOVED
FROM ELECTRONIC BALLAST
B
YEL
VIOLET +
RED*
JUNCTION
BOX
BLUE**
STAB-IN CONNECTOR (2 CONDUCTORS)
BLUE
YEL/BLK
BROWN -
CHARGE
LIGHT
VIOLET +
SWITCH BOX
W G
ELECTRONIC
A.C. BALLAST
WHT/BLK
RED
WHITE
YEL/BLK
BROWN -
B
WHITE
BLUE / WHT
BLUE
CHARGE
LIGHT
WHITE
WHT / BLK
BLACK
ORG / BLK
ORG/BLK
GREEN
BLK 120V
WHT / RED
ORG 277V
BLACK
GREEN
GROUND
For dimming ballast, connect
dimming leads to dimmer
WALL
SWITCH
WHT / BLK
BLACK
UNSWITCHED
120V OR COMMON
277V
(NETURAL)
WHITE*
WHITE*
WALL
SWITCH
TEST
SWITCH
GROUND
LAMPHOLDER 2
VIOLET
TAN
®
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720