Download JVC KD-G405 User's Manual

KD-G455/KD-G405
ENGLISH
CD RECEIVER
!"
KD-G455/KD-G405
‰∑¬
`a=
‡§√◊ËÕ߇≈Ëπ CD
KD-G455/KD-G405
SOUND
ATT
KD-G455
U
R SOURCE F
KD-G455
D
VOL
VOL
SOUND
ATT
KD-G405
U
R SOURCE F
KD-G405
D
VOL
VOL
•
This unit is equipped with the display demonstration. To cancel it, see page 8.
•
! !"#$%&'("#)*+,- 8 •
‡§√◊ËÕßπ’È ‰¥È√—∫°“√µ‘¥µ—Èß°“√ “∏‘µ¿“æª√–°Õ∫ À“°µÈÕß°“√¬°‡≈‘° ‚ª√¥¥Ÿ ÀπÈ“ 8
For installation and connections, refer to the separate manual.
!"#$%&'()*+,-./0
°√ÿ≥“¥Ÿ§ŸË¡◊Õ∑’Ë·¬°µË“ßÀ“° „π°“√µ‘¥µ—Èß·≈–°“√‡™◊ËÕ¡µËÕ
INSTRUCTIONS
!"
§”·π–π”
GET0180-001A
[U]
Cover001A_KD-G455_405[U]1.p65
1
8/12/03, 10:49 AM
ENGLISH
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
How to reset your unit
While holding SEL (select), press
This will reset the built-in microcomputer.
(standby/on attenuator) for more than 2 seconds.
(standby/on attenuator)
SEL (select)
Notes:
• Your preset adjustments—such as preset channels or sound adjustments—will also be erased.
• If a disc is in the unit, it will eject when you reset the unit. Be careful not to drop the disc.
How to use the MODE button
If you press MODE, the unit goes into functions mode, then the number buttons and 5/∞ buttons
work as different function buttons.
Ex.: When number button 2 works as MO (monaural) button.
Time countdown indicator
To use these buttons for original functions again after pressing MODE, wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared.
• Pressing MODE again also clears the functions mode.
2
EN02-03_KD-G455_405[U]f.p65
2
3/12/03, 6:56 PM
ENGLISH
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
How to reset your unit ...............................
How to use the MODE button ...................
2
2
LOCATION OF THE BUTTONS ............ 4
Control panel .............................................
Remote controller ......................................
Preparing the remote controller ................
4
5
6
BASIC OPERATIONS ....................... 7
Turning on the power ................................
Canceling the display demonstration ........
Setting the clock ........................................
7
8
9
RADIO OPERATIONS ...................... 10
Listening to the radio ................................. 10
Storing stations in memory ....................... 12
Tuning in to a preset station ...................... 13
CD OPERATIONS ........................... 14
Playing a CD .............................................
Locating a track or a particular portion
on a CD ..................................................
Selecting CD playback modes ..................
Playing a CD Text ......................................
Prohibiting disc ejection ............................
14
MP3 OPERATIONS ......................... 19
Playing an MP3 disc ................................. 19
Locating a file or a particular portion
on an MP3 disc ....................................... 20
Selecting MP3 playback modes ................ 22
SOUND ADJUSTMENTS ................... 23
Selecting preset sound modes
(C-EQ: custom equalizer) ....................... 23
Adjusting the sound .................................. 24
OTHER MAIN FUNCTIONS ................ 25
Changing the general settings (PSM) ....... 25
Detaching the control panel ...................... 27
CD CHANGER OPERATIONS
(only for KD-G455) .................................. 28
Playing discs ............................................. 28
Selecting the playback modes .................. 31
EXTERNAL COMPONENT OPERATIONS
15
16
17
17
TROUBLESHOOTING ...................... 33
MP3 INTRODUCTION ...................... 18
MAINTENANCE ............................. 36
What is MP3? ............................................ 18
How are MP3 files recorded and played
back? ...................................................... 18
Handling discs ........................................... 36
BEFORE USE
*For safety....
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
(only for KD-G455) .................................. 32
Playing an external component ................. 32
SPECIFICATIONS ........................... 37
*Temperature inside the car....
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
3
EN02-03_KD-G455_405[U]f.p65
3
3/12/03, 6:56 PM
LOCATION OF THE BUTTONS
ENGLISH
Control panel
Display window
KD-G455 KD-G405
1
(standby/on attenuator) button
2 SEL (select) button
3 FM/AM button
4 • For KD-G455
CD CD-CH (CD changer) button
• For KD-G405
CD button
5 Loading slot
6 Display window
7 0 (eject) button
8 EQ (equalizer) button
9 Remote sensor
p 5 (up) button
+10 button
q Control dial
w Number buttons
e MO (monaural) button
r SSM (Strong-station Sequential Memory)
button
t RPT (repeat) button
y RND (random) button
u MODE button
i DISP (display) button
4/¢
buttons
o
;
(control panel release) button
a ∞ (down) button
–10 button
Display window
s Tuner reception indicators
MO (monaural), ST (stereo)
d MP3 indicator
f CH (CD changer) indicator
• Only for KD-G455: Lights up only when
connecting to a CD changer.
g CD indicator
h Playback item/mode indicators
RND (random),
(disc),
(folder),
RPT (repeat)
j LOUD (loudness) indicator
k EQ (equalizer) indicator
l Sound mode (C-EQ: custom equalizer)
indicators
ROCK, CLASSIC, POPS, HIP HOP, JAZZ,
USER
/ Disc information indicators
TAG (ID3 Tag),
(folder),
(track/file)
z Main display
x Source display
Volume level indicator
c Tr (track) indicator
4
EN04-06_KD-G455_405[U]f.p65
4
3/12/03, 6:55 PM
SOUND
ATT
U
R SOURCE F
D
VOL
VOL
ENGLISH
3 • Selects the preset stations while listening to
the radio.
Each time you press the button, the preset
station number increases, and the selected
station is tuned in.
• Skips to the first file of the previous folder
while listening to an MP3 disc.
Each time you press the button, you can
move to the previous folder and start playing
the first file.
• For KD-G455:
While playing an MP3 disc on an MP3compatible CD changer;
– Skips to the previous disc if pressed briefly.
– Skips to the previous folder if pressed and
held.
Note: While playing a CD on a CD changer, this
always skips to the previous disc.
Remote controller
4 Functions the same as the control dial on the
main unit.
Note: These buttons do not function for the
preferred setting mode (PSM) adjustment.
1 • Turns on the unit if pressed when the unit is
turned off.
• Turns off the unit if pressed and held until
“SEE YOU” appears on the display.
• Drops the volume level in a moment if
pressed briefly.
Press again to resume the volume.
2 • Selects the band while listening to the radio.
Each time you press the button, the band
changes.
• Skips to the first file of the next folder while
listening to an MP3 disc.
Each time you press the button, you can
move to the next folder and start playing the
first file.
• For KD-G455:
While playing an MP3 disc on an MP3compatible CD changer;
– Skips to the next disc if pressed briefly.
– Skips to the next folder if pressed and held.
Note: While playing a CD on a CD changer, this
always skips to the next disc.
5 Selects the sound mode (C-EQ: custom
equalizer).
Each time you press the button, the sound
mode (C-EQ) changes.
6 Selects the source.
Each time you press the button, the source
changes.
7 • Searches for stations while listening to the
radio.
• Fast-forwards or reverses the track/file if
pressed and held while listening to a disc.
• Skips to the beginning of the next track/file
or goes back to the beginning of the current
(or previous) tracks/files if pressed briefly
while listening to a disc.
5
EN04-06_KD-G455_405[U]f.p65
5
16/12/03, 6:16 PM
ENGLISH
Preparing the remote controller
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
Remote sensor
• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of
the remote controller decreases, replace the
battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction
indicated by the arrow using a ball-point
pen or a similar tool.
2) Remove the battery holder.
(back side)
2. Place the battery.
Slide the battery into the holder with the +
side facing upwards so that the battery is
fixed in the holder.
3. Return the battery holder.
Insert again the battery holder by pushing it
until you hear a clicking sound.
(back side)
WARNING:
• Store the battery in a place where children
cannot reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble, or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery
to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off
heat, crack, or start a fire.
• When throwing away or saving the battery, wrap
it in tape and insulate; otherwise, the battery
may start to give off heat, crack, or start a fire.
• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack, or start a fire.
CAUTION:
DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight for
a long time. Otherwise, it may be damaged.
Lithium coin
battery (product
number: CR2025)
6
EN04-06_KD-G455_405[U]f.p65
6
3/12/03, 6:55 PM
ENGLISH
BASIC OPERATIONS
1
3
2
Turning on the power
1
Volume level appears.
Turn on the power.
Volume level indicator
Note on One-Touch Operation:
When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.
2
Adjust the sound as you want.
(See pages 23 and 24.)
To drop the volume in a moment
Select the source.
(For KD-G455)
(For KD-G405)
To operate the tuner (FM or AM),
see pages 10 – 13.
To play a CD,
see pages 14 – 17.
To play an MP3 disc,
see pages 19 – 22.
To operate the CD changer (only for
KD-G455), see pages 28 – 31.
To operate the external component (LINE IN)
(only for KD-G455), see page 32.
3
4
Press
briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
• If you turn the control dial, you can also restore
the sound.
To turn off the power
Press and hold
for more than one
second.
“SEE YOU” appears, then the unit turns off.
• If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.
Adjust the volume.
To increase the volume
To decrease the volume
CAUTION on Volume Setting:
Discs produce very little noise compared with
other sources. If the volume level is adjusted for
the tuner, for example, the speakers may be
damaged by the sudden increase in the output
level. Therefore, lower the volume before playing a
disc and adjust it as required during playback.
7
EN07-09_KD-G455_405[U]f.p65
7
3/12/03, 6:55 PM
ENGLISH
Canceling the display
demonstration
3
When shipped from the factory, display
demonstration has been activated, and starts
automatically when no operations are done for
about 20 seconds.
• It is recommended to cancel the display
demonstration before you use the unit for the
first time.
To cancel the display demonstration, follow
the procedure below:
1
Select “DEMO OFF.”
DEMO OFF
4
DEMO ON
Finish the setting.
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 25.)
To activate the display demonstration, repeat
the same procedure and select “DEMO ON” in
step 3.
2
Select “DEMO” if not shown on the
display.
8
EN07-09_KD-G455_405[U]f.p65
8
3/12/03, 6:55 PM
ENGLISH
Setting the clock
1
To check the current clock time or change the
display mode
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 25.)
Press DISP (display) repeatedly.
Each time you press the button, the
display changes as follows:
• During tuner operation:
Frequency
2
• During disc operation:
Set the hour.
1 Select “CLOCK H” (hour) if not shown on
the display.
2 Adjust the hour.
1
3
2
Elapsed
playing time
Track title
1 Select “CLOCK M” (minute).
2 Adjust the minute.
Disc title /
performer
2
• During external component operation (only
for KD-G455):
LINE IN
4
Clock
Notes:
• While playing an audio CD, “NO NAME” appears
for the disc title/performer and the track title.
• For indication change while playing a CD Text or
an MP3 disc, see also pages 17 and 20.
Set the minute.
1
Clock
Clock
• During power off:
The power turns on and the clock time is
shown for 5 seconds, then the power turns off.
Finish the setting.
9
EN07-09_KD-G455_405[U]f.p65
9
3/12/03, 6:55 PM
ENGLISH
RADIO OPERATIONS
2
Listening to the radio
You can use either automatic searching or manual
searching to tune in to a particular station.
Searching for a station automatically:
Auto search
1
Start searching for a station.
To search for stations of
higher frequencies
To search for stations of lower frequencies
When a station is received, searching stops.
Select the band (FM1 – 3, AM).
Each time you press the
button, the band changes as
follows:
FM1
FM2
FM3
To stop searching before a station is
received, press the same button you have
pressed for searching.
AM
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Selected band appears.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
10
EN10-13_KD-G455_405[U]f.p65
10
3/12/03, 6:55 PM
1
1 Press MODE to enter the
Select the band (FM1 – 3, AM).
Each time you press the
button, the band changes as
follows:
FM1
FM2
FM3
AM
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2
3
When an FM stereo broadcast is hard to
receive:
Press and hold ¢
or
4
until “M” (manual) starts flashing on
the display.
functions mode while listening
to an FM stereo broadcast.
ENGLISH
Searching for a station manually:
Manual search
2 Press MO (monaural), while
“MODE” is still flashing on the
display, so that “MONO”
appears on the display.
Each time you press the button,
monaural mode turns on and off
alternately.
MO (monaural) indicator
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.
Tune in to a station you want while
“M” (manual) is still flashing.
To tune in to stations of
higher frequencies
To tune in to stations of lower frequencies
• If you release your finger from the button,
the manual mode will automatically turns
off after 5 seconds.
• If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for
FM and 9 kHz for AM) until you release
the button.
11
EN10-13_KD-G455_405[U]f.p65
11
16/12/03, 6:17 PM
ENGLISH
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strongstation Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).
1
Select the FM band (FM1 – 3) you
want to store FM stations into.
Each time you press the
button, the band changes as
follows:
FM1
2
FM2
FM3
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number
buttons—No.1 (lowest frequency) to No.6
(highest frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.
Ex.: Storing FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
1
AM
Each time you press the
button, the band changes as
follows:
Press MODE to enter the functions
mode.
FM1
2
3
Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
Press and hold SSM for about
2 seconds.
FM2
FM3
AM
Tune in to a station (in this example,
of 92.5 MHz).
To tune in to stations of
higher frequencies
To tune in to stations of lower frequencies
“SSM” flashes, then disappears when
automatic preset is over.
12
EN10-13_KD-G455_405[U]f.p65
12
3/12/03, 6:55 PM
Press and hold the number button
(in this example, 1) for more than
2 seconds.
Tuning in to a preset station
You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 12 and 13.
1
ENGLISH
3
Select the band (FM1 – 3, AM).
Each time you press the
button, the band changes as
follows:
FM1
Preset number flashes for a while.
4
Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
• A previously preset station is erased when a new
station is stored in the same preset number.
• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.
2
FM2
FM3
AM
Select the number (1 – 6) for the
preset station you want.
Note:
You can also use the 5 (up) or ∞ (down) button on
the unit to select the next or previous preset stations.
Each time you press the 5 (up) or ∞ (down) button,
the next or previous preset station is tuned in.
13
EN10-13_KD-G455_405[U]f.p65
13
3/12/03, 6:55 PM
ENGLISH
CD OPERATIONS
Refer “MP3 OPERATIONS” on pages 19 to 22 for
operating MP3 discs.
Playing a CD
Insert a CD into the loading slot.
The unit turns on, draws
the CD and starts
playback automatically.
Notes:
• When a CD is inserted upside down, “EJECT”
appears on the display and the CD automatically
ejects.
• If there is no CD in the loading slot, you cannot
select CD as the source. “NO DISC” appears on
the display.
• If the current disc is a CD Text, disc title/performer
and then track title will automatically appear.
To stop play and eject the CD
Note on One-Touch Operation:
When a CD is already in the loading slot, pressing
CD CD-CH (for KD-G455) or CD (for KD-G405)
turns on the unit and starts playback automatically.
CD indicator
Press 0.
CD play stops and the CD automatically ejects
from the loading slot. The source changes to the
previously selected source.
• If you change the source, CD play also stops
(without ejecting the CD).
Next time you select “CD” as the source, CD
play starts from where playback has been
stopped previously.
Current source indication
Total playing time Total track number
of the inserted disc of the inserted disc
Elapsed playing time
Notes:
• If the ejected disc is not removed for about 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust.
(Disc play will not start this time.)
• You can eject the disc even when the unit is turned
off.
Current track
number
All tracks will be played repeatedly until you stop
playback.
14
EN14-17_KD-G455_405[U]f.p65
14
3/12/03, 6:55 PM
To go to a track quickly (+10 and –10 buttons)
1 Press MODE to enter the functions mode
while playing a CD.
To fast-forward or reverse the track
Press and hold ¢
, while
playing a CD, to fast-forward the
track.
Press and hold
reverse the track.
ENGLISH
Locating a track or a
particular portion on a CD
2 Press +10 or –10.
4, while playing a CD, to
To skip 10 tracks* forwards
to the last track
To skip 10 tracks* backwards
to the first track
To go to the next or previous tracks
Press ¢
briefly, while
playing a CD, to go ahead to the
beginning of the next track.
Each time you press the button
consecutively, the beginning of
the next tracks is located and
played back.
Press
4 briefly, while playing a CD, to go
back to the beginning of the current track.
Each time you press the button consecutively,
the beginning of the previous tracks is located
and played back.
* First time you press +10 or –10 button, the
track skips to the nearest higher or lower
track with a track number of multiple ten (ex.
10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks (see “How to use the +10 and
–10 buttons” below).
• After the last track, the first track will be
selected, and vice versa.
How to use the +10 and –10 buttons
• Ex. 1: To select track number 32 while
playing track number 6
To go to a particular track directly
Press the number button corresponding to the
track number to start its playback.
Track 6
(Three times)
\ 10 \ 20 \ 30
(Twice)
\ 31 \ 32
• Ex. 2 : To select track number 8 while
playing track number 36
• To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than one
second.
Track 36
(Three times)
\ 30 \ 20 \ 10
(Twice)
\9\8
15
EN14-17_KD-G455_405[U]f.p65
15
3/12/03, 6:55 PM
ENGLISH
Selecting CD playback modes
To play back tracks repeatedly
(Track Repeat Play)
To play back tracks at random
(Disc Random Play)
You can play back the current track repeatedly.
You can play back all tracks on the CD at random.
1 Press MODE to enter the
functions mode while playing a
CD.
2 Press RND (random), while
“MODE” is still flashing on the
display, so that “DISC RND”
appears on the display.
Each time you press the button,
disc random play mode turns on
and off alternately.
RND and
1 Press MODE to enter the
functions mode while playing a
CD.
2 Press RPT (repeat), while
“MODE” is still flashing on the
display, so that “TRK RPT”
appears on the display.
Each time you press the button,
track repeat play mode turns on
and off alternately.
RPT indicator
(disc) indicators
When disc random play is turned on, the
RND and
indicators light up on the display. A
track randomly selected starts playing.
When track repeat play is turned on, the RPT
indicator lights up on the display. The current
track starts playing repeatedly.
16
EN14-17_KD-G455_405[U]f.p65
16
3/12/03, 6:55 PM
Prohibiting disc ejection
In a CD Text, some information about the disc (its
disc title, performer, and track title) is recorded.
This CD Text information will be shown
automatically when you play a CD Text.
You can prohibit disc ejection and can lock a disc
in the loading slot.
To change the CD Text information
manually, select text display mode while
playing a CD Text.
Press DISP (display) repeatedly.
Each time you press the button,
the display changes as follows:
ENGLISH
Playing a CD Text
While pressing CD CD-CH (for KD-G455)
or CD (for KD-G405), press and hold 0
for more than 2 seconds.
(For KD-G455)
or
Disc title / performer
(For KD-G405)
(
Track title
lights up on the display)
“EJECT” flashes on the display for about 5 seconds,
and the disc is locked and cannot be ejected.
Elapsed playing time and
Current track number
Clock and
Current track number
Notes:
• The display shows up to 8 characters at one time
and scrolls if there are more than 8 characters.
See also “To select the scroll mode—SCROLL” on
page 26.
Some characters or symbols will not be shown (and
be blanked) on the display.
(Ex. “ABCå!d#” ]“ABCA D ”)
• When you press DISP (display) while playing an
audio CD, “NO NAME” appears for the disc title/
performer and the track title.
• When track title is shown, the Tr indicator and
current track number also appear on the right side
of the display.
To cancel the prohibition and unlock the
disc
While pressing CD CD-CH (for KD-G455) or CD
(for KD-G405), press and hold 0 again for more
than 2 seconds.
“EJECT” appears on the display, and the disc
ejects from the loading slot.
17
EN14-17_KD-G455_405[U]f.p65
17
3/12/03, 6:55 PM
ENGLISH
MP3 INTRODUCTION
What is MP3?
MP3 is an abbreviation of Motion Picture Experts
Group (or MPEG) Audio Layer 3. MP3 is simply a
file format with a data compression ratio of 1:10
(128 Kbps*).
* Bit rate is the average number of bits that one
second of audio data will consume. The unit used is
Kbps. To get a better audio quality, choose a higher
bit rate. The most popular bit rate for encoding is
128 Kbps.
How are MP3 files recorded
and played back?
MP3 “files (tracks)” can be recorded in “folders”
—in PC terminology.
During recording, the files and folders can be
arranged in a way similar to arranging files and
folders of computer data.
“Root” is similar to the root of a tree. Every file
and folder can be linked to and be accessed from
the root.
The illustration below shows an example of how
MP3 files are recorded on a CD-R or CD-RW,
how they are played back, and how they are
searched for on this unit.
• For details information about the MP3
discs, refer to “A Guide to MP3/WMA”
(separate volume).
Compatible with ID3 Tag
Extra information data such as album title,
performer name, song title, recording year, music
genre and a brief comment can be stored within
an MP3 file.
This unit can show both ID3v1 (Version 1) and
ID3v2 (Version 2) tags on the display. (See page
20.)
• Some characters cannot be shown correctly.
• If both ID3v1 and ID3v2 are recorded on a
disc, ID3v2 information will be shown.
Notes:
• This unit can read a CD-ROM containing MP3
files. However, if non-MP3 files are recorded
together with MP3 files, this unit will take a longer
time to scan the disc. It may also cause the unit to
malfunction.
• This unit cannot read or play an MP3 file without
the extension code <.mp3>.
• This unit is not compatible with MP3 file encoded
with Layer 1 and Layer 2 formats.
• This unit is not compatible with Playlist**.
** A playlist is a simple text file, used on a PC, which
enables users to make their own playback order
without physically rearranging the files.
Hierarchy
Level 1
Level 2
Level 3
Level 4
01
02
03
ROOT
05
6
3
4
10
5
1
11
2
12
04
Level 5
7
01
: Folder and their playback
order
8
9
1
: MP3 files and their playback
order
18
EN18-18_KD-G455_405[U]f.p65
18
3/12/03, 6:55 PM
ENGLISH
MP3 OPERATIONS
Refer also to “CD OPERATIONS” on pages
14 to 17.
Playing an MP3 disc
Insert an MP3 disc into the loading slot.
Note on One-Touch operation:
When a disc is already in the loading slot, pressing
CD CD-CH (for KD-G455) or CD (for KD-G405)
turns on the unit and starts playback automatically.
CD indicator
Notes:
• MP3 discs require a longer readout time.
(It differs due to the complexity of the folder/file
configuration.)
• When playback starts, folder and file names (or ID3
tags) will automatically appear. (See also page 20.)
• If you change the source or turn the power off, disc
playback stops (without ejecting the disc).
Next time you select the CD player as the source or
turn the power on, disc play starts from where
playback has been stopped previously.
To stop play and eject the disc
Press 0.
Playback stops and the disc automatically ejects
from the loading slot.
Current source indication
MP3 indicator
Total folder
number
Total file
number
Ex.: When the disc contains 19 folders and
144 MP3 files
All files will be played repeatedly until you stop
playback.
19
EN19-22_KD-G455_405[U]f.p65
19
3/12/03, 6:55 PM
ENGLISH
To change the display information
While playing back an MP3 file, you can change
the MP3 disc information shown on the display.
Press DISP (display) repeatedly.
Each time you press the button,
the display changes to show the
following:
• When “TAG DISP” is set to “TAG ON”
(initial setting: see page 26)
Album name / performer
(folder name*)
(TAG lights up on the display)
Track title (file name*)
(TAG lights up on the display)
Elapsed playing time and
Current file number
Clock and
Current file number
* If an MP3 file does not have ID3 tags, folder
name and file name appear. In this case, the
TAG indicator will not light up on the display.
• When “TAG DISP” is set to “TAG OFF”
(
Folder name
lights up on the display)
(
File name
lights up on the display)
Elapsed playing time and
Current file number
Clock and
Current file number
Notes:
• The display shows up to 8 characters at a time and
scrolls if there are more than 8 characters.
See also “To select the scroll mode—SCROLL” on
page 26.
• When folder or file name is shown, current folder
number or the Tr indicator and current file number
also appear on the right side of the display.
Locating a file or a particular
portion on an MP3 disc
To fast-forward or reverse the file
Press and hold ¢
while
playing an MP3 disc, to fastforward the file.
Press and hold
4 while playing an MP3
disc, to reverse the file.
Note:
During this operation, you can only hear intermittent
sounds. (The elapsed playing time also changes
intermittently on the display.)
To skip to the next or previous files
briefly while
Press ¢
playing, to skip ahead to the
beginning of the next file.
Each time you press the button
consecutively, the beginning of
the next files is located and
played back.
Press
4 briefly, while playing, to skip back
to the beginning of the current file.
Each time you press the button consecutively,
the beginning of the previous files is located and
played back.
To go to a particular file quickly within the
current folder (+10 and –10 buttons)
1 Press MODE to enter the functions mode
while playing an MP3 disc.
2 Press +10 or –10.
To skip 10 files* forwards to
the last file
To skip 10 files* backwards to
the first file
20
EN19-22_KD-G455_405[U]f.p65
20
3/12/03, 6:55 PM
How to use the +10 and –10 buttons
• Ex. 1: To select file number 32 while playing
file number 6
(Three times)
File 6
(Twice)
\ 10 \ 20 \ 30
\ 31 \ 32
• Ex. 2 : To select file number 8 while playing
file number 36
File 36
(Three times)
\ 30 \ 20 \ 10
(Twice)
\9\8
To go to a particular folder directly
IMPORTANT:
To directly select the folders using the number
button(s), it is required that folders are
assigned 2 digit numbers at the beginning of
their folder names. (This can only be done
during the recording of CD-Rs or CD-RWs.)
Ex.: If folder name is “01 ABC”
= Press 1 to go to Folder 01 ABC.
If folder name is “1 ABC,” pressing 1
does not work.
If folder name is “12 ABC”
= Press and hold 6 (12) to go to Folder
12 ABC.
Press the number button corresponding to the
folder number to start playing the first file in the
selected folder.
ENGLISH
* First time you press +10 or –10 button, the
file skips to the nearest higher or lower file
with a file number of multiple ten (ex. 10th,
20th, 30th).
Then each time you press the button, you
can skip 10 files (see “How to use the +10
and –10 buttons” below).
• After the last file, the first file will be
selected, and vice versa.
• To select a folder number from 01 – 06:
Press 1 (7) – 6 (12) briefly.
• To select a folder number from 07 – 12:
Press and hold 1 (7) – 6 (12) for more than one
second.
Notes:
• If
indicator flashes on the display after you have
selected a folder, it means that the folder does not
contain any MP3 files.
• You cannot directly select a folder with a number
greater than 12.
To select a particular file in a folder, press
or
4 after selecting the folder.
¢
To skip to the next or previous folder
Press 5 (up) while playing an
MP3 disc to skip to the next
folder.
Each time you press the button
consecutively, the next folder is
located (and the first file in the
folder starts playing, if recorded).
Press ∞ (down) while playing an MP3 disc to
skip back to the previous folder.
Each time you press the button consecutively,
the previous folder is located (and the first file in
the folder starts playing, if recorded).
Note:
If the folder does not contain any MP3 files, it is
skipped.
21
EN19-22_KD-G455_405[U]f.p65
21
3/12/03, 6:55 PM
ENGLISH
Selecting MP3 playback modes
To play back files repeatedly
(Track Repeat/Folder Repeat Play)
To play back files at random
(Folder Random/Disc Random Play)
You can play back the current file or all the files
in the current folder repeatedly.
1 Press MODE to enter the
You can play back all files of the current folder or
all files on the MP3 disc at random.
functions mode while playing an
MP3 disc.
1 Press MODE to enter the
functions mode while playing an
MP3 disc.
2 Press RPT (repeat), while
“MODE” is still flashing on the
display, so that “TRK RPT” or
“FLDR RPT” appears on the
display.
Each time you press the button,
the repeat play mode changes
as follows:
2 Press RND (random), while
“MODE” is still flashing on the
display, so that “FLDR RND” or
“DISC RND” appears on the
display.
Each time you press the button,
the random play mode changes
as follows:
TRK RPT
FLDR RPT
Canceled
FLDR RND
DISC RND
RPT indicator
Canceled
RND and
(folder) indicators
Ex.: When you select “TRK RPT”
Ex.: When you select “FLDR RND”
Mode
Mode
Active
indicator
Plays at random
FLDR RND RND and
indicators
light up.
All files of the
current folder, then
files of the next
folder and so on.
DISC RND RND and
indicators
light up.
All files on the disc.
Active
indicator
Plays repeatedly
TRK RPT
RPT indicator The current (or
lights up.
specified) file.
FLDR RPT
and RPT
indicators
light up.
All files of the
current (or
specified) folder.
22
EN19-22_KD-G455_405[U]f.p65
22
3/12/03, 6:55 PM
Selecting preset sound modes
(C-EQ: custom equalizer)
You can select a preset sound mode (C-EQ:
custom equalizer) suitable to the music genre.
Select the sound mode you want.
Each time you press the
button, the sound modes
change as follows:
USER
JAZZ
ROCK
CLASSIC
HIP HOP
POPS
Indication
For:
Preset values
BAS
TRE
LOUD
USER
(Flat sound)
00
00
OFF
ROCK
Rock or
disco music
+03
+01
ON
CLASSIC
Classical
music
+01
–02
OFF
POPS
Light music
+04
+01
OFF
HIP HOP
Funk or rap
music
+02
00
ON
JAZZ
Jazz music
+02
+03
OFF
ENGLISH
SOUND ADJUSTMENTS
Note:
You can adjust each sound mode to your preference.
Once you make an adjustment, it is automatically
stored for the currently selected sound mode. See
“Adjusting the sound” on page 24.
Indication pattern changes for each
sound mode except for “USER.”
Ex.: When you select “ROCK”
23
EN23-24_KD-G455_405[U]f.p65
23
3/12/03, 6:54 PM
ENGLISH
Adjusting the sound
*1 When you adjust the bass, treble, or loudness, the
You can adjust the sound characteristics to your
preference.
1
Select the item you want to adjust.
Each time you press the
button, the adjustable items
change as follows:
TRE
(treble)
FAD
Adjust the setting.
VOL
LOUD
BAL
(loudness)
(balance)
To increase the level or
turn on the loudness
Range
To decrease the level or
turn off the loudness
–06 (min.)
|
+06 (max.)
Indication pattern changes as
you adjust the bass or treble.
To do:
Adjust the bass.
TRE*1
Adjust the treble.
–06 (min.)
|
+06 (max.)
FAD*2
Adjust the front
and rear speaker
balance.
R06 (Rear only)
|
F06 (Front only)
BAL
Adjust the left
and right speaker
balance.
L06 (Left only)
|
R06 (Right only)
LOUD*1
Boost low and high
frequencies to
LOUD ON
produce a well|
balanced sound
LOUD OFF
at low volume
level.
VOL*3
2
(fader)
(volume)
Indication
BAS*1
BAS
(bass)
adjustment you have made is stored for the
currently selected sound mode (C-EQ) including
“USER.”
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 Normally the control dial works as the volume
control. So you do not have to select “VOL” to
adjust the volume level.
*4 Depending on the amplifier gain control setting.
(See page 26 for details.)
Adjust the volume. 00 (min.)
|
30 or 50 (max.)*4
Ex. 1: When you adjust “TRE” (treble)
LOUD indicator
Ex. 2: When you turn on the loudness
3
Repeat steps 1 and 2 to adjust the
other items.
To reset each sound mode to the factory
settings, repeat the same procedure and
reassign the preset values listed in the table on
page 23.
24
EN23-24_KD-G455_405[U]f.p65
24
13/12/03, 2:11 PM
OTHER MAIN FUNCTIONS
Adjust the PSM item selected.
ENGLISH
3
Changing the general settings
(PSM)
You can change the items listed in the table
below by using the PSM (Preferred Setting
Mode) control.
Basic Procedure
1
2
4
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(See below.)
5
Repeat steps 2 and 3 to adjust the
other PSM items if necessary.
Finish the setting.
Select the PSM item you want to
adjust.
Preferred Setting Mode (PSM) items
• For detailed operations of each PSM items, refer to the pages listed in the table.
Indications
Selectable values/items
DEMO
Display demonstration
CLOCK H
Hour adjustment
CLOCK M
Minute adjustment
DIMMER
Dimmer mode
SCROLL
Scroll mode
DEMO OFF
DEMO ON
Factory-preset See
settings
page
DEMO ON
1 – 12
1 (1:00)
00 – 59
00 (1:00)
8
9
OFF
ON
ONCE
AUTO
OFF
EXT IN*
External component
TAG DISP
Tag display
AMP GAIN
Amplifier gain control
OFF
26
ONCE
26
CHANGER
LINE IN
CHANGER
26
TAG OFF
TAG ON
TAG ON
26
LOW PWR
HIGH PWR
HIGH PWR
26
* Only for KD-G455: Displayed only when one of the following sources is selected—FM, AM, and CD.
25
EN25-27_KD-G455_405[U]f.p65
25
3/12/03, 6:54 PM
ENGLISH
To select the dimmer mode—DIMMER
You can dim the display at night (according to
your preference).
When shipped from the factory, dimmer is
deactivated.
• OFF:
• ON:
Cancels the dimmer.
Activates the dimmer.
To select the scroll mode—SCROLL
You can select the scroll mode for the disc
information (when the entire text cannot be
shown at once).
When shipped from the factory, scroll mode is set
to “ONCE.”
• ONCE:
• AUTO:
• OFF:
Scrolls only once.
Repeats the scroll (5-second
intervals in between).
Cancels scroll mode.
Note:
Even if the scroll mode is set to “OFF,” you can scroll
the display by pressing DISP (display) for more than
one second.
To select the external component to use
—EXT IN (only for KD-G455)
You can connect the external component to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
To use the external component as the playback
source through this unit, you need to select
which component—CD changer or external
component—to use.
When shipped from the factory, CD changer is
selected as the external component.
• CHANGER: To use the CD changer.
• LINE IN:
To use the external component
other than CD changer.
To turn the tag display on or off
—TAG DISP
An MP3 file can contain file information called
“ID3 Tag” where its album name, performer, track
title, etc. are recorded.
There are two versions–ID3v1 (ID3 Tag version
1) and ID3v2 (ID3 Tag version 2). If both ID3v1
and ID3v2 are recorded on a disc, ID3v2
information will be shown.
When shipped from the factory, “TAG ON” is
selected.
• TAG ON:
• TAG OFF:
Turns on the ID3 tag display while
playing MP3 files.
• If an MP3 file does not have ID3
tags, folder name and file name
appear.
Turns off the ID3 tag display while
playing MP3 files. (Only the folder
name and file name can be
shown.)
To select the amplifier gain control
—AMP GAIN
You can change the maximum volume level of
this unit. When the maximum power of the
speakers is less than 50 W, select “LOW PWR”
to prevent them from being damaged.
When shipped from the factory, “HIGH PWR” is
selected.
• LOW PWR: You can adjust the volume level
from “VOL 00” to “VOL 30.”
Note:
If you change the setting from
“HIGH PWR” to “LOW PWR” while
listening at a volume level more than
30, the unit automatically changes the
volume level to “VOL 30.”
• HIGH PWR: You can adjust the volume level
from “VOL 00” to “VOL 50.”
Note:
For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).
26
EN25-27_KD-G455_405[U]f.p65
26
3/12/03, 6:54 PM
You can detach the control panel when leaving
the car.
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel
holder.
Attaching the control panel
1
Insert the left side of the control
panel into the groove on the panel
holder.
ENGLISH
Detaching the control panel
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
1
2
Unlock the control panel.
2
Press the right side of the control
panel to fix it to the panel holder.
Lift and pull the control panel out of
the unit.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.
3
Put the detached control panel into
the provided case.
Connectors
27
EN25-27_KD-G455_405[U]f.p65
27
3/12/03, 6:54 PM
ENGLISH
CD CHANGER OPERATIONS
This section is only for KD-G455.
Playing discs
We recommend that you use the JVC MP3compatible CD changer with your unit.
Select the CD changer (CD-CH).
By using this CD changer, you can play back
your original CD-Rs (Recordable) and CD-RWs
(Rewritable) recorded either in audio CD format
or in MP3 format.
• You can also connect other CH-X series
CD changers (except CH-X99 and CH-X100).
However, they are not compatible with MP3
discs, so you cannot play back MP3 discs.
• You cannot use the KD-MK series CD
changers with this unit.
Before operating your CD changer:
• Refer also to the Instructions supplied for
your CD changer.
• If no discs are in the magazine of the CD
changer or the discs are inserted upside
down, “NO DISC” will appear on the display.
If this happens, remove the magazine and
set the discs correctly.
• If no magazine is loaded in the CD changer,
“NO MAG” appears on the display. If this
happens, insert the magazine in the CD
changer.
• If “RESET 1” – “RESET 8” appears on the
display, something is wrong with the
connection between this unit and the CD
changer. If this happens, check the
connection and make sure the cords are
connected firmly. Then, press the reset
button of the CD changer.
CD
CD-CH*
* If you have changed “EXT IN” setting to “LINE IN”
(see page 26), you cannot select the CD changer.
• When the current disc is an MP3 disc:
Playback starts from the first folder of the
current disc once file check is completed.
Selected disc number
MP3 indicator
(folder) indicator
Selected folder
number
Note:
Folder name appears on the display instead of
“ROOT,” if an MP3 disc contains a folder.
28
EN28-31_KD-G455_405[U]f.p65
28
3/12/03, 6:54 PM
Selected disc number
Elapsed playing
time
Current track
number
Notes:
• When you press CD CD-CH, the power
automatically comes on. You do not have to press
to turn on the power.
• If you change the source, CD changer play also
stops. Next time you select the CD changer as the
source, CD changer play starts from where
playback has been stopped previously.
• When you start playing back a CD Text or MP3
disc, disc information will automatically appear on
the display. (See pages 17 and 20.)
To go to a particular disc directly
Press the number button corresponding to the
disc number to start its playback (while the CD
changer is playing).
ENGLISH
• When the current disc is a CD:
Playback starts from the first track of the
current disc.
• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than
one second.
To fast-forward or reverse the track/file
Press and hold ¢
, during
play, to fast-forward the track/file.
Press and hold
the track/file.
4, during play, to reverse
Note:
During this operation, you can only hear intermittent
sounds. (The elapsed playing time also changes
intermittently on the display.)
To skip to the next or previous tracks/files
Press ¢
briefly during play,
to skip ahead to the beginning of
the next track/file.
Each time you press the button
consecutively, the beginning of
the next tracks/files is located
and played back.
Press
4 briefly during play, to skip back to
the beginning of the current track/file.
Each time you press the button consecutively,
the beginning of the previous tracks/files is
located and played back.
29
EN28-31_KD-G455_405[U]f.p65
29
3/12/03, 6:54 PM
ENGLISH
This operation is only possible when
using JVC MP3-compatible CD changer
(CH-X1500).
To go to a track/file quickly (+10 and –10
buttons)
1 Press MODE to enter the functions mode
while playing a disc.
2 Press +10 or –10.
To skip 10 tracks/files* forwards
to the last track/file
To skip 10 tracks/files*
backwards to the first track/file
* First time you press +10 or –10 button, the
track/file skips to the nearest higher or lower
track/file with a track/file number of multiple
ten (ex. 10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks/files (see “How to use the +10
and –10 buttons” below).
• After the last track/file, the first track/file will
be selected, and vice versa.
Note:
If the current playing disc is an MP3 disc, files are
skipped within the same folder.
To skip to the next or previous folder
(only for MP3 discs)
Press 5 (up) while playing an
MP3 disc, to go to the next folder.
Each time you press the button
consecutively, the next folder is
located, and the first file in the
folder starts playback.
Press ∞ (down) while playing an MP3 disc, to go
to the previous folder.
Each time you press the button consecutively,
the previous folder is located, and the first file in
the folder starts playback.
To show the disc information for CD Text
and MP3 discs
This is possible only when connecting a JVC CD
changer equipped with CD Text and/or MP3 disc
information reading capability.
Select text display mode while playing a
CD Text or an MP3 disc.
• For details, see page 17 about CD Text disc
information and page 20 about MP3 disc
information.
How to use the +10 and –10 buttons
• Ex. 1: To select track/file number 32 while
playing track/file number 6
(Three times)
Track/File 6 \ 10 \ 20 \ 30
(Twice)
\ 31 \ 32
• Ex. 2 : To select track/file number 8 while
playing track/file number 36
(Three times)
Track/File 36 \ 30 \ 20 \ 10
(Twice)
\9\8
30
EN28-31_KD-G455_405[U]f.p65
30
3/12/03, 6:54 PM
To play back tracks/files at random
(Folder Random/Disc Random/Magazine
Random Play)
To play back tracks/files repeatedly
(Track Repeat/Folder Repeat/Disc Repeat
Play)
1 Press MODE to enter the
functions mode during play.
ENGLISH
Selecting the playback modes
1 Press MODE to enter the
2 Press RPT (repeat), while
functions mode during play.
“MODE” is still flashing on the
display.
Each time you press the button,
the repeat play mode changes
as follows:
2 Press RND (random), while
“MODE” is still flashing on the
display.
Each time you press the button,
the random play mode changes
as follows:
For MP3 discs:
For MP3 discs:
FLDR RND
DISC RND
Canceled
MAG RND
DISC RND
MAG RND
TRK RPT
FLDR RPT
Canceled
DISC RPT
TRK RPT
DISC RPT
For CDs:
For CDs:
Canceled
(disc) and RPT indicators
Canceled
RND indicator
Ex.: When you select “DISC RPT”
Ex.: When you select “MAG RND”
Note:
MP3 indicator also lights up if the current playing disc
is an MP3 disc.
Mode
Active
indicator
Plays at random
FLDR RND* RND and
indicators
light up.
All files of the
current folder, then
files of the next
folder and so on.
DISC RND
All tracks/files of
the current (or
specified) disc.
MAG RND
RND and
indicators
light up.
RND indicator All tracks/files of
lights up.
the inserted discs.
Note:
MP3 indicator also lights up if the current playing disc
is an MP3 disc.
Mode
Active
indicator
Plays repeatedly
TRK RPT
RPT indicator
lights up.
The current (or
specified) track/
file.
FLDR RPT*
and RPT
indicators
light up.
All files of the
current (or
specified) folder of
the current disc.
DISC RPT
and RPT All tracks/files of
indicators light the current (or
up.
specified) disc.
* “FLDR RPT” is only applicable for MP3 discs.
* “FLDR RND” is only applicable for MP3 discs.
31
EN28-31_KD-G455_405[U]f.p65
31
3/12/03, 6:54 PM
ENGLISH
EXTERNAL COMPONENT OPERATIONS
This section is only for KD-G455.
Playing an external component
2
3
Turn on the connected component
and start playing the source.
Adjust the volume.
You can connect the external component to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
Preparations:
• For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).
• Before operating the external component using the
following procedure, select the external input
correctly. See “To select the external component to
use—EXT IN” on page 26.
1
4
Adjust the sound as you want.
(See pages 23 and 24.)
Select the external component
(LINE IN).
CD
LINE IN
• If “LINE IN” does not appear on the display, see
page 26 and select the external input (“LINE IN”).
Note on One-Touch Operation:
When you press CD CD-CH, the power automatically
comes on. You do not have to press
to turn
on the power.
32
EN32-32_KD-G455_405[U]f.p65
32
13/12/03, 2:12 PM
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms
Remedies
The volume level is set to the
minimum level.
Adjust it to the optimum level.
Connections are incorrect.
Check the cords and
connections.
• This unit does not work
at all.
The built-in microcomputer may
have functioned incorrectly due
to noise, etc.
While holding SEL (select),
press
(standby/on
attenuator) for more than
2 seconds to reset the unit.
(Your preset adjustments will
also be erased.) (See page 2.)
• SSM (Strong-station
Sequential Memory)
automatic preset does
not work.
Signals are too weak.
Store stations manually.
• Static noise while
listening to the radio.
The antenna is not connected
firmly.
Connect the antenna firmly.
• Disc automatically ejects.
Disc is inserted upside down.
Insert the disc correctly.
• CD-R/CD-RW cannot be
played back.
• Tracks on the CD-R/
CD-RW cannot be
skipped.
CD-R/CD-RW is not finalized.
• Insert a finalized CD-R/
CD-RW.
• Finalize the CD-R/CD-RW
with the component which
you used for recording.
• Disc can be neither
played back nor ejected.
Disc is locked.
Unlock the disc.
(See page 17.)
The CD player may have
functioned incorrectly.
While holding
(standby/on attenuator), press
0 (eject) for more than
2 seconds. Be careful not to
drop the disc when it is ejected.
You are driving on rough roads.
Stop playback while driving on
rough roads.
Disc is scratched.
Change the disc.
Connections are incorrect.
Check the cords and
connections.
No disc in the loading slot.
Insert a disc into the loading slot.
Disc is inserted incorrectly.
Insert the disc correctly.
Disc Playback
FM/AM
General
• Sound cannot be heard
from the speakers.
Causes
• Disc sound is sometimes
interrupted.
• “NO DISC” appears on
the display.
ENGLISH
TROUBLESHOOTING
33
EN33-37_KD-G455_405[U]f.p65
33
16/12/03, 6:20 PM
ENGLISH
Symptoms
Causes
MP3 Playback
• Disc cannot be played
back.
Remedies
No MP3 files are recorded on
the disc.
Change the disc.
MP3 files do not have the
extension code <.mp3> in their
file names.
Add the extension code <.mp3>
to their file names.
MP3 files are not recorded in
the format compliant with ISO
9660 Level 1, Level 2, Romeo,
or Joliet.
Change the disc.
(Record MP3 files using a
compliant application.)
• Noise is generated.
The file played back is not an
MP3 file (although it has the
extension code <.mp3>).
Skip to another file or change
the disc. (Do not add the
extension code <.mp3> to nonMP3 files.)
• A longer readout time is
required (“CHECK”
keeps flashing on the
display).
Readout time varies due to the
complexity of the folder/file
configuration.
Do not use too many hierarchies
and folders. Also, do not record
any other types of audio tracks
together with MP3 files.
• Files cannot be played
back as you have
intended them to play.
Playback order is determined
when the files are recorded.
• Elapsed playing time is
not correct.
This sometimes occurs during
play. This is caused by how the
files are recorded on the disc.
•
The current folder does not
contain any MP3 file.
Select another folder.
• “NO FILES” appears on
the display.
The current disc does not
contain any MP3 file.
Insert a disc that contains MP3
files.
• Correct characters are
not displayed (e.g. album
name).
This unit can only display
alphabets (capital: A–Z),
numbers, and a limited number
of symbols.
indicator flashes on
the display.
34
EN33-37_KD-G455_405[U]f.p65
34
3/12/03, 6:53 PM
• “NO DISC” appears on the
display.
Causes
Remedies
No disc is in the magazine.
Insert discs into the
magazine.
Discs are inserted upside down.
Insert discs correctly.
• “NO MAG” appears on the
display.
No magazine is loaded in the
CD changer.
Insert the magazine.
• “RESET 8” appears on the
display.
This unit is not connected to the
CD changer correctly.
Connect this unit and the
CD changer correctly and
press the reset button of
the CD changer.
• “RESET 1” – “RESET 7”
appears on the display.
• The CD changer does not
work at all.
Press the reset button of
the CD changer.
The built-in microcomputer may
function incorrectly due to noise,
etc.
CD Changer
Symptoms
ENGLISH
This section is only for KD-G455.
While holding SEL (select),
(standby/
press
on attenuator) for more
than 2 seconds to reset the
unit. (Your preset
adjustments will also be
erased.) (See page 2.)
About mistracking:
Mistracking may result from driving on extremely rough roads. This does not damage the unit and the disc,
but will be annoying.
We recommend that you stop disc play while driving on such rough roads.
35
EN33-37_KD-G455_405[U]f.p65
35
4/12/03, 12:56 PM
ENGLISH
MAINTENANCE
Handling discs
When playing a CD-R or CD-RW
This unit has been designed to reproduce CDs,
CD-Rs (Recordable), CD-RWs (Rewritable), and
CD Texts.
• This unit is also compatible with MP3 discs.
How to handle discs
When removing a disc
Center holder
from its case, press down
the center holder of the case
and lift the disc out, holding
it by the edges.
• Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
• Make sure to store discs into the cases after
use.
To keep discs clean
A dirty disc may not be played
correctly. If a disc does become
dirty, wipe it with a soft cloth in a
straight line from center to edge.
To play new discs
New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
unit may reject the disc.
To remove these rough spots, rub
the edges with a pencil or ball-point pen, etc.
Moisture condensation
Moisture may condense on the lens inside the
CD player in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and leave
the unit turned on for a few hours until the
moisture evaporates.
Sticker
Warped
disc
Before playing back CD-Rs or CD-RWs, read
their instructions or cautions carefully.
• Use only “finalized” CD-Rs or CD-RWs.
• Some CD-Rs or CD-RWs may not be played
back on this unit because of their disc
characteristics, and for the following reasons:
– Discs are dirty or scratched.
– Moisture condensation on the lens inside the
unit.
– The pickup lens inside the unit is dirty.
• CD-RWs may require a longer readout time
since the reflectance of CD-RWs is lower than
that of regular CDs.
• CD-Rs or CD-RWs are susceptible to high
temperatures or high humidity, so do not leave
them inside your car.
• Do not use following CD-Rs or CD-RWs:
– Discs with stickers, labels, or protective seal
stuck to the surface.
– Discs on which labels can be directly printed
by an ink jet printer.
Using these discs under high temperatures or
high humidity may cause malfunctions or
damage to discs. For example,
– Stickers or labels may shrink and warp a
disc.
– Stickers or labels may be peeled off so discs
cannot be ejected.
– Print on discs may get sticky.
Read instructions or cautions about labels and
printable discs carefully.
CAUTIONS:
• Do not insert 8 cm discs (single CDs) into the
loading slot. (Such discs cannot be ejected.)
• Do not insert any disc of unusual shape—like a
heart or flower; otherwise, it will cause a
malfunction.
• Do not expose discs to direct sunlight or any
heat source or place them in a place subject to
high temperature and humidity. Do not leave
them in a car.
• Do not use any solvent (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean discs.
Sticker
residue
Disc
36
EN33-37_KD-G455_405[U]f.p65
36
3/12/03, 6:53 PM
Stick-on
label
AUDIO AMPLIFIER SECTION
CD PLAYER SECTION
Maximum Power Output:
Front: 50 W per channel
Rear: 50 W per channel
Continuous Power Output (RMS):
Front: 19 W per channel into 4 Ω, 40 Hz to
20 000 Hz at no more than 0.8%
total harmonic distortion.
Rear: 19 W per channel into 4 Ω, 40 Hz to
20 000 Hz at no more than 0.8%
total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range
Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.0 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Type: Compact disc player
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
MP3 decoding format:
MPEG 1/2 Audio Layer 3
Max. Bit Rate:
320 Kbps
TUNER SECTION
Frequency Range
FM:
87.5 MHz to 108.0 MHz
AM:
531 kHz to 1 602 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB
ENGLISH
SPECIFICATIONS
GENERAL
Power Requirement
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):
182 mm × 52 mm × 150 mm
Panel Size (approx.):
188 mm × 58 mm × 11 mm
Mass (approx.):
1.4 kg (excluding accessories)
Design and specifications are subject to change
without notice.
[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
37
EN33-37_KD-G455_405[U]f.p65
37
16/12/03, 6:20 PM
CD qÒGA l u¹œ«—
wd
KD-G455/KD-G405
SOUND
ATT
KD-G455
U
R SOURCE F
KD-G455
D
VOL
VOL
SOUND
ATT
KD-G405
U
R SOURCE F
KD-G405
D
VOL
VOL
Æ∏ W×H# dE½« ¨÷«dF²Ýô« WHOþË ¡UGô Æ÷dF« WýUA ÷«dF²Ý« WHOþuÐ œË
Ò e “UN'« «c¼ •
ÆqBHM*« ULOKF²« VO² WFł«d vłd¹ ¨ öOu²«Ë VOd²« UOKLF
ULOKF²« VO²
EN, CT, TH, AR
1203KKSMDTJEIN
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
CoverARKD-G455_405[U]1
2
12/12/03, 5:24 PM
KD-G455/KD-G405
Installation/Connection Manual
!"#$
°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß
GET0180-003A
[U]
1203KKSMDTJEIN
EN, CT, TH, AR
qOu²«ØVOd²« ULOKFð VÒO²
ENGLISH
This unit is designed to operate on 12 V DC,
NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage
inverter is required, which can be purchased at
JVC car audio dealers.
The following parts are provided for this unit.
After checking them, please set them correctly.
—UOð WDÝ«uÐ jI qLFO “UN'« «c¼ rL bI
WOzUÐdN WLE½« ¨Xu ±≤ ¨DC dýU³% wzUÐdN
«c¼ q¦% œułË ÂbŽ WUŠ w ÆVUÝ i¹—Qð
‰u×% «b<²Ý« V−¹ ¨pð—UOÝ w ÂUEM«
…eNłô« ¡öË s% ‰u;« «c¼ ¡«dý sJ1Ë ¨ÃU²u
ÆJVC W—U% «—UOJK WOðuB«
!"#$% 1 2 V !"#$%&' ™ÿ¥ª√–°Õ∫π’È ‰¥È√—∫°“√ÕÕ°·∫∫¡“‡æ◊ËÕ„™Èß“π°—∫√–∫∫
!"#$%&'()*+,-./'0( °√–· ‰øøÈ“ “¬¥‘π¢—È«≈∫°√–· µ√ß 12 ‚«≈∑Ï
!"#$% JVC !"#$%&'( À“°√∂¬πµÏ¢Õߧÿ≥‰¡Ë ‰¥È „™È√–∫∫π’È
µÈÕß„™È‡§√◊ËÕß·ª≈ß°√–· ‰ø™Ë«¬
´÷Ëß “¡“√∂À“´◊ÈÕ‰¥È®“°√È“π¢“¬‡§√◊ËÕ߇ ’¬ß√∂¬πµÏ
Parts list for installation and
connection
wÐdŽ
‰∑¬
A/B
Hard case/Control panel
!
!"#$%&'(
JVC
√“¬°“√ Ë«πª√–°Õ∫ ”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π
!"#$%&'()
!"#$%&'()*
qOu²«Ë VOd²« ¡«eł« WLzUK
Æ“UN'« l% …œËe% WOU²« ¡«ełô«
qJAÐ rN³Odð vłd¹ ¨¡«ełô« Ác¼ h× bFÐ
Æ`O×
Ë«πª√–°Õ∫µËÕ‰ªπ’È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È À≈—
ß®“°µ√«® Õ∫·≈È« ª√—∫µ—È߇§√◊ËÕß„ÀÈ∂Ÿ°µÈÕß
C
Sleeve
!
E
Power cord
!"#$
D
Trim plate
≈—ß∫√√®ÿ/ÀπÈ“ª—¥
ª≈Õ°ÀÿÈ¡
·ºËπ‚≈À–¢Õ∫·µËß
“¬‡§‡∫‘≈°”≈—ß
rJײ« WŠuØVK ‚ËbM
wK«u« qJON«
WM¹e« WŠu
WKUD« pKÝ
WOzUÐdNJ«
G
Battery
F
Remote controller
√’‚¡µ§Õπ‚∑√≈
·∫µ‡µÕ√’Ë
bFÐ sŽ rJײ« …bŠË
U¹—UD³«
J
Mounting bolt (M5 x 20 mm)
!=EM5 x 20 mmF
≈—°µ‘¥ (M5 x 20 ¡‘≈≈‘‡¡µ√)
©r?K% ≤∞ x M5® VOd²« —ULJ%
H
Washer (ø5)
=Eø5F
ª√–‡°Áπ«ß·À«π (ø5)
©µ dDK® qOu²« ÂUJŠ« WIKŠ
CR2025
K
Rubber cushion
!"
L
Handles
!"
¬“ß°—π°√–·∑°
§—π∫—ߧ—∫
WOÞUD*« …uA(«
UUJ*«
INSTALLATION
(IN-DASH MOUNTING)
The following illustration shows a typical
installation. If you have any questions or require
information regarding installation kits, consult
your JVC car audio dealer or a company
supplying kits.
• If you are not sure how to install this unit
correctly, have it installed by a qualified
technician.
!"#$%&'()*+,-./
!"#$%&'()*+,- JVC !"#$%&'()*+,-.
• !"#$%&#'()*+,-./
!"#$%&'
!"#$%&
!
uKÐUð ‡ qš«œ ® “UN'« VOdð
©…—UOJ«
°“√µ‘¥µ—ßÈ (°“√ª√–°Õ∫·ºßÀπÈ“ª—∑¡Ï‡¢È“)
¿“æµ—«Õ¬Ë“ßµËÕ‰ªπ’È· ¥ß∂÷ß°“√µ‘¥µ—Èß·∫∫∑—Ë«‰ª À“°§ÿ≥¡’ª—
≠À“À√◊ÕµÈÕß°“√¢ÈÕ¡Ÿ≈‡°’ˬ«°—∫™ÿ¥µ‘¥µ—Èß °√ÿ≥“ª√÷°…“°—
∫ºŸÈ¢“¬‡§√◊ËÕ߇ ’¬ß√∂¬πµÏ JVC ¢Õß∑Ë“πÀ√◊Õ∫√‘…—
• ™ÿ¥ª√–°Õ∫ ∂È“§ÿ≥‰¡Ë·πË„®«Ë“µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’È∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë
„ÀÈÀ“™Ë“ߺŸÈ‡™’ˬ«™“≠‡ªÁπºŸÈµ‘¥µ—Èß
4
2
1
B
I
Lock nut (M5)
!=EM5F
πÕµ≈ÁÕ§ (M5)
©M5® XO³¦²« WuL
VOd²« WI¹dÞ wU²« w×O{u²« rÝd« sO³¹
Ò
WłUŠ Ë« «—UJH²Ý« „UM¼ ÊU «–« ÆWOU¦*«
vłd¹ ¨VOd²« «Ëœ« ’uB<Ð U%uKF*
W—U% «—UOJK WOðuB« …eNłô« Ÿ“u% …—UA²Ý«
Æ «Ëœô« …cN WŽ“u*« WdA« Ë« JVC
“UN'« VOdð WOHOJÐ p²dF% ÂbŽ WUŠ w •
“UN'« VOdð WOKLŽ „dð vłd¹ ¨`O× qJAÐ
Æ…eNłô« Ác¼ q¦% VOd² q¼R%Ë h²<% h<A
!
Do the required electrical connections.
!"#$%&'
D
µËÕ “¬‰øµ“¡∑’Ë°”À𥉫È∑—ÈßÀ¡¥
ÆWÐuKD*« WOzUÐdNJ« öOu²« qLŽ«
K
C
3
L
*1 When you stand the unit, be careful
not to damage the fuse on the rear.
*1 !"#$%&'()*+,
!
*1 ‡¡◊ËÕ§ÿ≥µ—Èß™ÿ¥ª√–°Õ∫¢÷Èπ √–«—
@
D
*1
B
!"#$%&!"'()*+,-.(/0
1
2
B
!
D
1
J
ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀȵËÕ°—π‡¢È“∑’Ë
XO³¦² VÝUM% qJAÐ WMJô« w¦½«
ÊUJ*« w rJ×% qJAÐ wK«u« qJON«
Æ`O×B«
…—UOJ« uKÐUð s% “UN'« Ÿe½
ÆwHK)« ¡e'« —dŠ ¨“UN'« Ÿe½ q³K
Insert the two handles, then pull them as illustrated so that
the unit can be removed.
!"#$%&'()*+,-."/01234$56
!"#$%&'()*
„ ˧π— ∫—ߧ—∫ 2 Õ—π≈ß„π√ËÕß ”À√—∫„™Èæπ— ≈«¥ ¥—ß¿“æ ®“°π—πÈ „Àȇ≈◊ÕË π™ÿ¥ª√–°Õ∫ÕÕ° „π¢≥–
∑’˧ËÕ¬ Ê ¥÷ߧ—π∫—ߧ—∫∑—Èß Õß Õ—πÕÕ°®“°°—π
sJ1 YO×Ð sÒO³% u¼ UL rN³×Ý« p– bFÐË ¨5²UJ*« qšœ«
Æ“UN'« Ÿe½
Install1-2KD-G455_405-1
m
°ËÕπ®–∂Õ¥™ÿ¥ª√–°Õ∫ „ÀȪ≈¥ÀπÈ“µ—¥ Ë«π∑È“¬°ËÕπ
1
16/12/03, 1:56 PM
m
Ÿ
°“√∂Õ¥™ÿ¥ª√–°Õ∫
3
m
Bend the appropriate tabs to hold the
sleeve firmly in place.
!"#$%&'()
!"
¤
Before removing the unit, release the rear
section.
m
⁄
qł« s% t³²½« ¨“UN'« nOKuð bMŽ ±*
vKŽ œułu*« “uOH« —dCð ÂbŽ
ÆWOHK)« WN'«
Removing the unit
4
53
~
ßլ˓∑”„ÀÈø«‘ Ï∫√‘‡«≥ Ë«π∑È“¬‡ ’¬À“¬
C
18
L
‡¡◊ËÕ„™Èµ—«¬÷¥·∫∫‡≈◊Õ°‰¥È (“¡“√∂‡≈◊Õ°‡ª‘¥§È“߉«È ‰¥È) /
When installing the unit without using the sleeve / !"#$%&'($ /
‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫‚¥¬‰¡Ë „™Èª≈Õ°ÀÿÈ¡ / wK«u« qJON« «b<²Ý« ÊËbÐ “UN'« Vdð U%bMŽ
WOU{ô« W%UŽb« «b<²Ý« bMŽ
In a Toyota for example, first remove the car radio and install the unit in its place.
When using the optional stay / !"# /
!"TOYOTA !"#$%&' ()*+,-./*0123'4567
Fire wall
µ—«Õ¬Ë“߇™Ëπ „π√∂¬πµÏ‚µ‚¬µÈ“ „ÀÈ∂Õ¥«‘∑¬ÿµ‘¥√∂¬πµÏÕÕ°°ËÕπ·≈–µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’ȇ¢È“‰ª·∑π
ºπ—ß°—π‰ø
Stay (option)
!"#$
o¹d(« s% W¹UL(« —«bł
Æt½UJ% w “UN'« VÒ— p– bFÐ ôË« …—UOJ« u¹œ«— Ÿe½« ¨Uðu¹uð Ÿu½ «—UOÝ w ¨‰U¦*« qO³Ý vKŽ
Flat type screws (M5 x 8 mm)*
!" EM5 x 8 mmF*
°√ŸÀ—«‡√’¬∫ (M5 x 8 ¡‘≈≈‘‡¡µ√)*
*©rK% ∏ x M5® …bŽUI« W¹u²J% wž«dÐ
µ—«¬÷¥ (‡≈◊Õ°‰¥È)
Dashboard
J
H
©WOU{«® W%UŽb«
I
·ºßÀπÈ“ª—∑¡Ï
Bracket*
*
Screw (option)
!"#$%
…—UOJ« uKÐUð
·∑Ëπ√Õß√—∫*
°√Ÿ (‡≈◊Õ°‰¥È)
C
* Not included with this unit.
* !"#$%
* ‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π
Æ“UN'« «c¼ l% œÒËe% dOž *
Flat type screws (M5 x 8 mm)*
!" EM5 x 8 mmF*
°√ŸÀ—«‡√’¬∫ (M5 x 8 ¡‘≈≈‘‡¡µ√)*
*©rK% ∏ x M5® …bŽUI« W¹u²J% wž«dÐ
*XO³¦²« WOH²
©wU{«® wždÐ
Pocket
Bracket*
*
°–‡ª“–
VOł
·∑Ëπ√Õß√—∫*
*XO³¦²« WOH²
Note
Install the unit at an angle of less than 30˚.
!"#$% 30° !
µ‘¥µ—ßÈ ™ÿ¥ª√–°Õ∫∑’¡Ë ¡ÿ µË”°«Ë“ 30 Õß»“
ÆWł—œ ≥∞ s% qK« W¹Ë«“ vKŽ “UN'« V—
Ò
À¡“¬‡Àµ
: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer
screws are used, they could damage the unit.
: !"#$%&'()*+,=8 mm= !"#$%&' !"()*+,-#
: ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫≈ß„π·∑Ëπ√Õß√—∫‰«È „ÀÈ„™È °√Ÿ¬“«¢π“¥ 8 ¡‘≈≈‘‡¡µ√ ∂È“„™È °√Ÿ¬“«°«Ë“π’ÈÕ“®∑”„ÀÈ™ÿ¥ª√–°Õ∫‡ ’¬À“¬‰¥ô
s% ‰uÞ« wž«dР«b<²Ý« WUŠ w ÆrK% ∏ ‰uÞ wž«dÐ ‰ULF²Ý« s% bQð ¨VOd²« UOH² vKŽ “UN'« VOdð bMŽ ∫WEŠö%
Æ“UN−K —d{ Ë« nKð p– V³J¹ Ê« sJ1 ¨rK% ∏
ELECTRICAL CONNECTIONS
!
To prevent short circuits, we recommend that
you disconnect the battery’s negative terminal
and make all electrical connections before
installing the unit.
• Be sure to ground this unit to the car’s
chassis again after installation.
!"#$%&'()*+,#-./01
!"#$%&'()*+
• !"#$%&'()*+,-./01
Notes:
• Replace the fuse with one of the specified
rating. If the fuse blows frequently, consult
your JVC car audio dealer.
• It is recommended to connect to the speakers
with maximum power of more than 50 W (both
at the rear and at the front, with an impedance
of 4 Ω to 8 Ω). If the maximum power is less
than 50 W, change “AMP GAIN” setting to
prevent the speakers from being damaged
(see page 26 of the INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of
the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be
careful not to touch it when removing this unit.
• !"#$%&'()* !+,-
!"#$% JVC !"#$%&'
• !"#$%&'()*+,'50 W !" 4 Ω – 8 Ω !"#$%&
50 W ! “AMP GAIN” !"#$%
!" !"#$%&'=26 • !"#$%&'()*+,-.'!/
°“√‡™◊ËÕ¡‚¥¬„™È ‰øøÈ“
‡æ◊ËÕªÈÕß°—π°“√‡°‘¥‰øøÈ“≈—¥«ß®√ ¢Õ·π–π”„ÀȪ≈¥¢—È«·∫µ‡µÕ√’Ë≈∫ÕÕ°
·≈È«®÷ßµËÕ “¬‰ø°ËÕ𵑥µ—È߇§√◊ËÕß
• µ√«® Õ∫„ÀÈ·πË „®«Ë“‰¥È‡¥‘𠓬¥‘πµËÕ√–À«Ë“߇§√◊ÕË ß°—∫µ—«∂—ß
√∂¬πµÏ „À¡Ë·≈È«À≈—ß®“°µ‘¥µ—ßÈ
À¡“¬‡Àµÿ :
• „™Èæ°‘ ¥— ®”‡æ“–·∑πø‘« À“°ø‘« Ï¢“¥∫ËÕ¬ „ÀȪ√÷°…“√È“
π¢“¬‡§√◊ÕË ß‡ ’¬ß√∂¬πµÏ JVC
• ¢Õ·π–π”„ÀȵËÕ≈”‚æß ∑’Ë¡’°”≈—ߢ—∫ Ÿß ÿ¥‡°‘π°«Ë“ 50 W
(∑—ÈߥȓπÀπÈ“·≈–¥È“πÀ≈—ß ¡’§Ë“§«“¡µÈ“π∑“π 4 Ω ∂÷ß 8 Ω)
∂È“°”≈—ߢ—∫µË”°«Ë“ 50 W „Àȇª≈’ˬπ§Ë“ “AMP GAIN”
‡æ◊ËÕªÈÕß°—π‰¡Ë„ÀÈ≈”‚æß™”√ÿ¥ (¥ŸÀπÈ“ 26 „π§ŸË¡◊Õ„™Èß“π)
•
°“√ªÈÕß°—π°“√≈—¥«ß®√ ®–µÈÕßæ—π¢—È« “¬µ–°—Ë«
∑’Ë ‰¡Ë„™È·≈È«¥È«¬‡∑ ªæ—𠓬‰ø
!
• !"#$%&'(%)*+#,-. • ·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ÈÕπ¡“°À≈—ß®“°„™È √–¡—¥√–«—ßլ˓‰ª
—¡º— ‡¡◊ËÕ∂Õ¥™ÿ¥ª√–°Õ∫π’È
!"#$%&'()*
WOzUÐdNJ« öOu²«
wu½ ¨WOzUÐdNJ« dz«Ëb« w dOBIð ÀËbŠ lM*
q qLŽË VUJ« W¹—UD³« qOuð ·dÞ qBHÐ
Æ“UN'« VOdð q³K WOzUÐdNJ« öOu²«
…d% …—UOJ?« qJO¼ l% “UN'« i¹—Qð s% bQð •
ÆVOd²« bFÐ WO½UŁ
∫ UEŠö%
UÝUOI« f?H½ qL×¹ dš¬ “uOHÐ “uOH« ‰b³²Ý •
qOË dA²?Ý« ¨“uOH« ‚«d²Š« —dJð «–« ÆWuu*«
ÆWOðuB« …—UOJ« …eNłô JVC
ÈuBK WKUÞ «– UŽULÝ l% qOu²« `BM¹ •
l% ¨ÂU%ô«Ë nK)« s% ö vKŽ® ◊«Ë µ∞ s% d¦«
ÈuBI« WKUD« X½U «–« Æ©ÂË« ∏ v« ÂË« ¥ WF½U2
“AMP GAIN” W¾?ONð l{Ë dOÒž ¨◊«Ë µ∞ s% qK«
Æ—dC« s% UŽULJ« lM*
Æ© ULOKF²« VO² s% ≤∂ W×H dE½«®
l{ ¨WOzUÐdNJ« ‡ …dz«b« dOBIð lM% qł« s% •
dOž „öÝô« ·«dÞ« vKŽ oô j¹dý
ÆWKLF²J*«
bFÐ «bł WMšUÝ …—«d(« iHš W×OH `³Bð •
Ÿe½ bMŽ UN²J%ö% ÂbŽ s% bQð Æ«b<²Ýô«
Æ“UN'«
Heat sink
·ºËπ√–∫“¬§«“¡√ÈÕπ
…—«d(« iHš W×OH
PRECAUTIONS on power supply
and speaker connections:
!"#$%&'()*
¢ÈÕ§«√√–«—ß ”À√—∫°“√µËÕ·À≈Ë߮˓¬°”≈—ß·≈–≈”‚æß:
• !"#$%&'&()*+,-./0
• DO NOT connect the speaker leads of the
!"#
power cord to the car battery; otherwise,
• !"#$%&%' !"()*+,the unit will be seriously damaged.
!"#$%&
• BEFORE connecting the speaker leads of the
power cord to the speakers, check the
speaker wiring in your car.
+
L -
-
+
R -
-
+
+
TROUBLESHOOTING
• լ˓µËÕ “¬µ–°—Ë«‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫·∫µ‡µÕ√’Ë√∂¬πµÏ ¡‘©–π—Èπ
™ÿ¥ª√–°Õ∫®–‰¥È√—∫§«“¡‡ ’¬À“¬¡“°
• °ËÕπ∑’®Ë –µËÕ “¬µ–°—«Ë ‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫≈”‚æß
„Àȵ√«® Õ∫°“√‡¥‘𠓬‰ø≈”‚æß„π√∂¢Õߧÿ≥„Àȇ√’¬∫√ÈÕ¬‡ ’¬°ËÕπ
+
L -
-
+
R -
-
+
+
!
°“√µ√«® Õ∫ª—≠À“¢—¥¢ÈÕß
• The fuse blows.
* Are the red and black leads connected
correctly?
• !"#
* !"#$%&'!"#$%()$*+
• Power cannot be turned on.
* Is the yellow lead connected?
• * !"#$
!"#$%&'$()
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• * !"#$
!"#$%&'()*+,-
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
• !"
* !"#$%&'()*+
* !"#$%L !R
– !"#$%
• Noise interfere with sounds.
* Is the rear ground terminal connected to the
car’s chassis using shorter and thicker cords?
• * • Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
• !"
* !"#$%&'()*+
* !"#$%L !R
– !"#$\
•
*
•
*
•
*
•
*
*
!"#
•
*
!"#
!"#$%&'()*+,*-./0
•
*
*
ø‘« Ï¢“¥
¡’°“√‡™◊ÕË ¡ “¬µ–°—«Ë ’¥”·≈– ’·¥ßլ˓ß∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë
‰¡Ë “¡“√∂‡ª‘¥‡§√◊ËÕ߉¥È
¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë« ’‡À≈◊ÕßÀ√◊Õ‰¡Ë
‰¡Ë¡’‡ ’¬ßÕÕ°®“°≈”‚æß
“¬µ–°—Ë« Ë«π∑’ËÕÕ°∑“ß≈”‚æ߇°‘¥‰øøÈ“≈—¥«ß®√À√◊Õ‰¡Ë
‡ ’¬ß‡æ’Ȭπ
“¬µ–°—Ë« Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
“¬¢—È«≈∫ ¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
‡ ’¬ß√∫°«π
¡’°“√„™È “¬ —ÈπÊ À√◊ÕÀπ“Ê µËÕ®“°‡§√◊ËÕß Ë«π∑’˵‘¥µ—Èß
‰«È∫πæ◊Èπ¥È“πÀ≈—ß°—∫µ—«∂—ß√∂¬πµÏÀ√◊Õ‰¡Ë
™ÿ¥ª√–°Õ∫√ÈÕπ¢÷Èπ
“¬µ–°—Ë« Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
“¬¢—È«≈∫ ¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
!"#
2
Install1-2KD-G455_405-1
2
16/12/03, 1:57 PM
WOzUÐdNJ« WKUD« b¹Ëeð ‰uŠ UNO³Mð
∫ UŽULJ« qOuðË
l% UŽULJ« WKUÞ b¹Ëeð „öÝ« qÒuð ô •
‰uBŠ v« ÍœR¹ p– Êô ¨…—UOJ« W¹—UDÐ
Æ UŽULJK —d{
l% UŽULJ« WKUÞ b¹Ëeð „öÝ« qOuð q³K •
UŽULJ« „öÝ« WJ³ý h׫ ¨ UŽULJ«
Æpð—UOÝ qš«œ
+
L -
-
+
R -
-
+
+
Õöô«Ë ‰UDŽô« sŽ Y׳«
Æ“uOH« ‚d²×¹
qJAÐ Wuu% œuÝô«Ë dLŠô« pKJ« q¼
ø`O×
ÆWOzUÐdNJ« WKUD« qOuð sJ1 ô
øôuu% dHô« pKJ« q¼
Æ UŽULJ« s% u —bB¹ ô
Ãdš pKÝ …dz«œ w dOBIð pUM¼ q¼
øWŽULJ«
ÆÁuA% uB«
ø÷—ôUÐ ôuu% WŽULJ« Ãdš pKÝ q¼
L ÈdJO« WŽULJK “≠” W³UJ« ·«dÞô« q¼
øiFÐ l% ÷—ôUÐ Wuu% R vMLO«Ë
Æ «uô« l% ZO−{ qš«bð
qJO¼ l% ‰uu% wHK)« w{—ô« ·dÞ q¼
øpLÝ«Ë dBK« „öÝ« ‰ULF²ÝUÐ …—UOJ«
Æ“UN'« s<J¹
ø÷—ôUÐ ôuu% WŽULJ« Ãdš pKÝ q¼
L ÈdJO« WŽULJK “≠” W³UJ« ·«dÞô« q¼
øiFÐ l% ÷—ôUÐ Wuu% R vMLO«Ë
•
*
•
*
•
*
•
*
*
•
*
•
*
*
ENGLISH
A
Typical Connections / !"#$ /
Before connecting: Check the wiring in the
vehicle carefully. Incorrect connection may
cause serious damage to this unit.
The leads of the power cord and those of the
connector from the car body may be different in
color.
1
2
3
Connect the colored leads of the power cord
in the order specified in the illustration
below.
°“√‡™◊ËÕ¡µËÕ·∫∫ª°µ‘ / WOł–uLM« öOu²«
!"#$%&'()*+%,&
!"#$%&'
!" #$%!&'(" )*+,-.
!"
1
2
3
wÐdŽ
‰∑¬
!"#$%&'()*+,-./+0
!"
!"#$%&'&()*+
°ËÕ•∑”°“•‡™•ËÕ¡µËÕ : µ•«®†Õ•°“•‡¥‘•†“¬‰ø„•••¬•µÏլ˓ߕ–¡—
¥•–«—լ˓„ÀȺ‘¥æ•“¥„•°“•‡™•ËÕ¡µËÕ™ÿ¥ª•–°Õ•™ÿ¥•’
°“•‡™•ËÕ¡µËÕº‘¥æ•“¥Õ“®∑”„Àȇ°‘¥§«“¡‡†’¬À“¬•È“¬·•ß°—•™ÿ¥ª•–
°Õ••’È ‰¥È“•µ–°—Ë«¢Õ߆“¬‰ø ·•–¢ÕßÕÿª°••ÏµËÕ‡™•ËÕ¡®“°µ—«•
ß••Õ“®¡’†’∑’Ë ‰¡Ë‡À¡•Õ•°—•
…—U?O??« w? „ö?Ýô« WJ³ý s# b$Qð ∫q?O?u?²?UÐ ¡b³« q³
Ê« s?J?1 Æ“U?N?'« qOuð WOKLŽ w QDš Àb×¹ ô v²Š WbÐ
Æ“UN−K wIOIŠ qDŽ ‰uBŠ v« ¡vÞU)« qOu²« V³¹
qu*« pKÝË WOzUÐdNJ« WUD« pKÝ Êu nK²C¹ Ê« sJ1
Æ…—UO« qJO¼ Êu sŽ
1 µËÕ “¬‰ø ’µ“¡≈”¥—∫∑’Ë√–∫ÿ„π√Ÿª¥È“π≈Ë“ß
2 ‡™◊ÕË ¡µËÕ°—∫ “¬Õ“°“»
3 ÿ¥∑È“¬ µËÕ Ë«π§«∫§ÿ¡°“√‡¥‘𠓬‰ø‡¢È“°—∫™ÿ¥ª√–°Õ∫™ÿ¥π’È
#$%&'
WOzUÐdNJ« WUD« pK W½uK*« „öÝô« qË«
ÆqHÝô« w œułu*« rÝd« w ·uu*« VOðd²UÐ
±
Æwz«uN« pKÝ qË«
≤
≥
Æ“UN'« l# „öÝô« q#UŠ qË« ¨«dOš«
Connect the antenna cord.
Finally connect the wiring harness to the unit.
Only for KD-G455: To CD changer jack or another external component (see diagram )
=KD-G455: =CD !"#$%&'=( ! )
KD-G455 ‡∑Ë“π—Èπ: ™ËÕ߇ ’¬∫µËÕ¢Õ߇§√◊ËÕ߇≈Ëπ´’¥ CD ≈À–Õÿª°√≥Ï¿“¬πÕ° (¥Ÿ·ºπ¿Ÿ¡
© jD<« dE½«® wł—U)« X½U½u³LJ« “UNł Ë« W−#b*« W½«uDÝô« ‰Òb³# f³I# CD ∫KD-G455 q¹œuLK jI
Rear ground terminal
!"#$%
®ÿ¥‡™◊ËÕ¡µËÕ “¬¥‘π¥È“πÀ≈—ß
wHK)« i¹—Q²« ·dÞ
15 A fuse
15 A 15
1
ø‘« Ï¢π“¥ 15 A
dO³#« ±µ “uO
Antenna terminal
!
¢—È« “¬Õ“°“»
Line out (see diagram )
!"#$%& “¬ÕÕ° (Line out) (¥Ÿ·ºπ¿Ÿ¡
©
*1 Not included for this unit
*1 !"#$
*1 ‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π
“UN'« «c¼ l# œÒËe# dOž±*
)
jD<« dE½«® j)« Ãdš
Black
wz«uN« ·dÞ
’¥”
2
3
1
«‘∑™Ï®ÿ¥√–‡∫‘¥
‰UF²ýô« ÕU²H#
*1
To metallic body or chassis of the car
!"#$%&'
œuÝ√
Ignition switch
!
*1
µËÕ°—∫‚§√ß‚≈À–À√◊Õ‡™ ´‘ ¢Õß√∂¬πµÏ
w½bF*« …—UO« qJO¼ Ë« w½bF*« r'« v«
Yellow*2
*2
’‡À≈◊Õß*2
dHò*
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
!"#$%&'()*+ !"#$,-./012
!"#$%&'()=12 V
2
Fuse block
!"
·ºßø‘« “uOH« WŽuL−#
µËÕ°—∫¢—È«∑’Ë¡’°√–· ‰øøÈ“„π·ºßø‘« Ï ´÷ËßµËÕ°—∫·∫µ‡µÕ√’Ë√∂¬πµ
(‚¥¬‰¡ËµÈÕß„™È «‘∑™Ï®ÿ¥√–‡∫‘¥) (12 ‚«≈∑ϧß∑’Ë)
«—Ëd#® W¹—UD³« l# Wuu*« “uOH« WŽuL−# w w(« ·dD« v«
©Xu ±≤ XÐUŁ® ©‰UF²ýô« ÕU²H0
*2 Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise power
cannot be turned on.
*2 !"#$%&'()*+,-.$/012345
!"#$%&'(
*2 °ËÕπ°“√µ√«® Õ∫°“√∑”ß“π¢Õß™ÿ¥ª√–°Õ∫π’È°ËÕπ∑’Ë®–µ‘¥µ—Èß
Red
µÈÕßµËÕ “¬µ–°—Ë«π’È°ËÕπ ¡‘©–π—Èπ®–‰¡Ë “¡“√∂‡ª‘¥‡§√◊ËÕ߉¥
’·¥ß
V−¹ ¨VO$d²« q³ “UN'« «c¼ qOGAð h× q³ ∫≤*
WUD« qOuð sJ1 ô p– ·öCÐ ¨pK« «c¼ qOuð
ÆWOzUÐdNJ«
dLŠ√
3
To an accessory terminal in the fuse block
!"#$%&'()*
µËÕ°—∫¢—È« Ë«πª√–°Õ∫„π·ºßø‘« “uOH« WŽuL−# qš«œ wU{ô« ·dD« v«
Blue with white stripe
!"#$
’πÈ”‡ß‘π≈“¬¢“«
iOÐôUÐ jDC# ‚—“« pKÝ
4
To the remote lead of other equipment or automatic antenna if any (200 mA max.)
!"#$%&'()*+,-.*/01234 200 mA
µËÕ “¬°—∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡ “Õ“°“»Õ—µ‚π¡—µ‘∂È“¡’ (¢π“¥ Ÿß ÿ¥ 200 mA)
błË Ê« wJOðU#uðËô« wz«uN« Ë« dšô« “UN−K bFÐ sŽ rJײ« pKÝ v«
©dO³#« wKO# ≤∞∞ bŠ vB«®
5
White with black stripe
!"#$
White Gray with black stripe
!"#$
’¢“«·∂∫¥”
’¢“« ’‡∑“·∂∫¥”
’‡∑“
œuÝôUÐ jDC# iOЫ pKÝ
iOÐ√ œuÝôUÐ jDC# ÍœU#— pKÝ
ÍœU#—
Left speaker (front)
!"#$%
Gray
Green with black stripe
!"#$
Green
Purple with black stripe
!"#$
’‡¢’¬«·∂∫¥”
’‡¢’¬«
’¡Ë«ß·∂∫¥”
’¡«Ë ß
œuÝôUÐ jDC# dCš« pKÝ
dCš«
œuÝôUÐ jDC# w½«uł—« pKÝ
w½«uł—«
Right speaker (front)
!"#$%
Left speaker (rear)
!"#$%
3
Right speaker (rear)
!"#$%
≈”‚æß´È“¬ (ÀπÈ“)
≈”‚æߢ«“ (ÀπÈ“)
≈”‚æß´È“¬ (À≈—ß)
≈”‚æߢ«“ (À≈—ß)
©WO#U#ô«® ÈdO« WŽUL«
©WO#U#ô«® vMLO« WŽUL«
©WOHK)«® ÈdO« WŽUL«
©WOHK)«® vMLO« WŽUL«
3
Install 3-4KD-G455_405-1
Purple
18/12/03, 3:40 PM
B
Connections Adding Other Equipment / !"#$%&'( /
°“√µËÕ‡æ‘Ë¡‡µ‘¡‡¢È“°—∫Õÿª°√≥ÏÕ◊Ëπ Ê / WOU{ô« Èdšô« …eNłô« qOuð
Amplifier / !" / ‡§√◊ËÕߢ¬“¬ / uB« rCC#
You can connect an amplifier and other
equipment to upgrade your car stereo system.
• Connect the remote lead (blue with white
stripe) to the remote lead of the other
equipment so that it can be controlled
through this unit.
• For amplifier only:
Disconnect the speakers from this unit,
connect them to the amplifier. Leave the
speaker leads of this unit unused.
!"#$%&'()*+, -./01
!"
• !"#$%&'(%)*+,-./0
!"#$%&'()*+),-./0
!
• !"#$%&'
!"#$%&'()*+,-.!/
!"#$%&'()*
§ÿ≥ “¡“√∂µËÕ°—∫·Õ¡æ≈‘ø“¬‡ÕÕ√Ï ·≈–Õÿª°√≥ÏÕπË◊ ʉ¥È ‡æ◊ÕË ‡æ‘¡Ë §ÿ≥
¿“æ‡ ’¬ß„ÀÈ°—∫√–∫∫ ‡µÕ√‘‚Õ¢Õß√∂¬πµÏ
• µËÕ “¬µ–°—«Ë √–¬–‰°≈ ( ’π”È ‡ß‘π≈“¬¢“«) ‡¢È“°—∫ “¬µ–°—«Ë √–¬–
‰°≈¢ÕßÕÿª°√≥ÏÕπË◊ Ê ‡æ◊ÕË ®– “¡“√∂§«∫§ÿ¡‚¥¬™ÿ¥ª√–°Õ∫π’ȉ¥È
• ”À√—∫‡§√◊ËÕߢ¬“¬‡∑Ë“π—Èπ :
∂Õ¥≈”‚æßÕÕ°®“°™ÿ¥ª√–°Õ∫π’È ·≈È«µËÕ‡¢È“°—∫‡§√◊ËÕߢ¬“¬
∑‘Èß “¬µ–°—Ë«≈”‚æߢÕß™ÿ¥ª√–°Õ∫π’È ‰«È
Rear speakers
!"
Y-connector (not supplied for this unit)
Y !"#$%&'()*
¢ÈÕµËÕ√Ÿªµ—« Y (‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’)È
©“UN'« l# œÒËe# dOž® Y qu#
Ò
Remote lead
!
≈”‚æßÀ≈—ß
WOHK)« UŽUL«
“¬µ–°—Ë«•–¬–‰°•
bFÐ sŽ rJײ« pKÝ
L
INPUT
L
R
R
Èdš« …eNł« Ë« u rCC# qOuð pMJ1
Æ…—UO« u¹dO²Ý “UNł ¡«œ« 5ײ
bFÐ sŽ rJײ« pKÝ qË« •
sŽ rJײ« pKÝ l# ©iOÐôUÐ jD<« ‚—“ô«®
“UN'UÐ rJײ« r²¹ YO×Ð dšô« “UN−K bFÐ
Æ“UN'« «c¼ ‰öš s#
∫ uB« rCC* jI •
l# rNKË« ¨“UN'« «c¼ s# UŽUL« qB«
«c¼ UŽULÝ „öÝ« „dð« Æ uB« rCC#
ƉULF²Ý« ÊËbÐ “UN'«
JVC Amplifier
JVC !"
‡§√◊ËÕߢ¬“¬‡ ’¬ß JVC
JVC W$—U# u rCC#
Remote lead (blue with white stripe)
!=E !"#$F
“¬µ–°—Ë«•–¬–‰°• ( ’πÈ”‡ß‘π≈“¬¢“«)
*3
©iOÐôUÐ jD<« ‚—“ô«® bFÐ sŽ rJײ« pKÝ
LINE OUT
L
L
R
R
To the remote lead of other equipment or automatic antenna if any
KD-G455
KD-G405
!"#$%&'()*+,-.*/01234
µËÕ “¬°—∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡ “Õ“°“»Õ—µ‚π¡—µ‘∂È“¡’
REAR FRONT
błË Ê« wJOðU#uðËô« wz«uN« Ë« dšô« “UN−K bFÐ sŽ rJײ« pKÝ v«
Signal cord (not supplied for this unit)
!"#$% !
Front speakers
!"
“¬‡§‡∫‘≈ —≠≠“≥ (‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
©“UN'« l# œÒËe# dOž® œdH# pKÝ
≈”‚æßÀπÈ“
WO#U#ô« UŽUL«
*3 Firmly attach the ground wire to the
metallic body or to the chassis of the car—
to the place not coated with paint (if coated
with paint, remove the paint before
attaching the wire). Failure to do so may
cause damage to the unit.
CD Changer / CD *3 !"#$%&'($)*+,-./-.
!"#$%&'()*+,-$%./0
!"#$%&'()*+,-./"01
!"#
*3
µËÕ≈«¥ “¬¥‘π„ÀÈ·πËπ‡¢È“°—∫µ—«∂—߇À≈Á° À√◊Õµ—«∂—ß√∂ ˙
µ√ß Ë«π ∑’Ë ‰¡Ë¡’ ’‡§≈◊Õ∫ (À“°¡’ ’‡§≈◊Õ∫Õ¬ŸË „ÀÈ¢Ÿ¥ ’ÕÕ°°ËÕπ
°ËÕπµËÕ≈«¥ “¬¥‘π) À“°‰¡ËªØ‘∫—µ‘µ“¡§”·π–π”π’È
‡§√◊ËÕßÕ“®™”√ÿ¥À√◊Õ‡ ’¬À“¬‰¥
Ë« qJO¼ l# rJ×# qJAÐ w{—ô« pK« qË« ∫≥*
wKD*« dOž l{u*« l# ‡‡ w½bF*« …—UO« rł
‰“« ¨ÊU¼bUÐ wKD# l{u*« ÊU$ «–«® ÊU¼bUÐ
qOuð WUŠ w Æ©pK« qOuð q³ ÊU¼b«
Ê« sJ1 ÊU¼b« W«“« ÊËœ qJON« l# pK«
Æ“UN'« «cN —d{ p– V³¹
/ ‡§√◊ÕË ß‡≈Ëπ´’¥’ CD / W−#b*« W½«uDÝô« ‰bÒ ³#
Only for KD-G455 / =KD-G455 / KD-G455 ‡∑Ë“π—Èπ / KD-G455 q¹œuLK jI
Refer also to page 28 of the INSTRUCTIONS.
!"#$%&'(=28 Connecting cord supplied for your CD changer
! !"#=CD ¥Ÿ¢ÈÕ·π–π”„πÀπÈ“ 28
“¬µËÕ„ÀÈ¡“æ√ÈÕ¡‡§√◊ËÕ߇≈Ëπ´’¥’
Æ ULOKF²« VO²$ s# ≤∏ W×H ÎUC¹√ lł«—
W−#b*« W½«uDÝô« ‰Òb³* œËe*« pK« qOuð
CAUTION / /
¢ÈÕ§«√√–«—ß / tO³Mð
• Before connecting the CD changer, make sure that the unit
is turned off.
• CD !"#$%&'()
•
°ËÕπ®–‡™◊ËÕ¡µËÕ‡§√◊ËÕ߇≈Ëπ´’¥’ °√ÿ≥“µ√«® Õ∫„ÀÈ·πË„®«Ë“‡§√◊ËÕ߇≈Ëπ´’¥’π—Èπª‘¥Õ¬
ÆqOGA²« sŽ …bŠu« ·UI¹« s# b$Qð ¨W−#b*« W½«uDÝô« ‰Òb³# qOuð q³
JVC CD changer
JVC CD ‡§√◊ËÕ߇≈Ëπ´’¥’ JVC
W−#b*« W½«uDÝô« ‰Òb³# JVC
KD-G455
External Component / ! / Õÿª°√≥Ï¿“¬πÕ° / wł—U)« X½U½u³LJ« “UNł
Only for KD-G455 / =KD-G455 / KD-G455 ‡∑Ë“π—Èπ / KD-G455 q¹œuLK jI
*4
*4
*4
Line Input Adapter KS-U57 (not supplied
for this unit)
!"#KS-U57
!"#$%
KS-U57 *4
Õ·¥ª‡µÕ√Ï “¬ —≠≠“≥‡¢È“
KS-U57 (‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
KS-U57 j)« qšœ ¨v¹UN# ¥*
©“UN' «cŽ l# œËd# dOž®
KD-G455
L
L
L
L
R
R
R
R
™ËÕ߇ ’¬∫µËÕ¢Õ߇§√◊ËÕ߇≈Ëπ´’¥
Signal cord (not supplied with this unit)
!"#$%&'()
CD
“¬‡§‡∫‘≈ —≠≠“≥ (‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
W−#b*« W½«uDÝô« ‰Òb³# f³I# CD
©“UN'« l# œÒËe# dOž® œdH# pKÝ
4
4
Õÿª°√≥Ï¿“¬πÕ°
wł—U)« X½U½u³LJ« “UNł
CD changer jack
CD !"
Install 3-4KD-G455_405-1
External component
!
18/12/03, 3:41 PM
•