1
Download Graco 3A0239F User's Manual
Transcript
Instructions - Parts Power Distribution Module 3A0239F EN For use with HFR, VRM, and VPM plural-component proportioners. For professional use only. Not approved for use in European explosive atmosphere locations. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 3 for model information. US Patent Pending r_24C860_3A0239_1a Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Replace Power Supply . . . . . . . . . . . . . . . . . . . . 6 Replace Circuit Breaker . . . . . . . . . . . . . . . . . . . 6 Electrical Schematics . . . . . . . . . . . . . . . . . . . . . . . 7 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 HFR Power Distribution Modules . . . . . . . . . . . 20 VRM Power Distribution Modules . . . . . . . . . . . 23 VPM Power Distribution Modules . . . . . . . . . . . 26 Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 30 Graco Information . . . . . . . . . . . . . . . . . . . . . . . . 30 2 3A0239F Models Models Description Maximum Amperes Description HFR Power Distribution Modules 230V, 1 Phase, Basic 55 A 230V, 1 Phase, Fully Loaded 116 A 230V, 3 Phase, Basic 29 A 230V, 3 Phase, Fully Loaded 73 A 400V, 3 Phase, Basic 55 A 400V, 3 Phase, Fully Loaded 63 A 200-240VAC, 1 phase, 50/60 Hz 2 wire and PE 200-240VAC, 3 phase Δ, 50/60 Hz 3 wire and PE 380-415VAC, 3 phase Y, 50/60 Hz 3 wire, neutral, and PE VRM Power Distribution Modules 230V, 3 Phase, Basic 60 A 230V, 3 Phase, Fully Loaded 105 A 400V, 3 Phase, Basic 55 A 400V, 3 Phase, Fully Loaded 75 A 200-240VAC, 3 phase Δ, 50/60 Hz 3 wire and PE 380-415VAC, 3 phase Y, 50/60 Hz 3 wire, neutral, and PE VPM Power Distribution Modules 230V, 3 Phase 75 A 200-240VAC, 3 phase Δ, 50/60 Hz 3 wire and PE 400V, 3 Phase 55 A 400V, 3 Phase 55 A 380-415VAC, 3 phase Y, 50/60 Hz 3 wire, neutral, and PE The Residual Current Device (RCD) must be rated at 300 mA if it is installed. Basic modules provide power to the control dispense system only. Fully loaded modules provide power to the control dispense system, four heat zones, and two feed tanks. See 400 V Power Requirements. 400 V Power Requirements • 400 V systems are intended for International voltage requirements. Not for voltage requirements in North America. • If a 400 volt configuration is operated in North America, a special transformer rated for 400 V (“Y” configuration (4 wire)) may be required. • North America mostly employs a 3 wire or Delta configuration. The two configurations are not interchangeable. 3A0239F 3 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. WARNING ELECTRIC SHOCK HAZARD This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock. • Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment. • Connect only to grounded power source. • All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations. EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. • Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure in this manual when equipment is not in use. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your distributor for information. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. • Do not kink or over bend hoses or use hoses to pull equipment. • Keep children and animals away from work area. • Comply with all applicable safety regulations. 4 3A0239F Troubleshooting Troubleshooting Problem Cause Solution No power received from DC power supply. Defective power supply. Check circuit breaker. Check power supply. Replace power supply. No power to MCM, heat zones, or tanks. Circuit breaker is tripping. Check circuit breaker for tripping and defects. Diagnose cause of circuit breaker tripping before resetting it. Replace defective parts if required. 3A0239F 5 Repair Repair Replace Power Supply Replace Circuit Breaker 1. Turn off system power. 1. Turn off system power. 2. Open electrical enclosure door. 2. Open electrical enclosure door. 3. Disconnect power supply (1a) wires from the filter (1c) and the electrical enclosure connector. 3. Disconnect wire harness from circuit breaker. 4. Remove circuit breaker. 4. Remove nuts and washers that secure power supply to electrical enclosure. 5. Install new power supply to electrical enclosure. Secure with nuts and washers. 5. Install new circuit breaker, and connect wire harness. 6. Close electrical enclosure door and turn on system power. 6. Connect power supply wires to the filter and the electrical enclosure connector. Wire Harness 7. Close electrical enclosure door and turn on system power. Wire Harness 1c 1a Connector r_24C680_3A0239_10a r_24C686_3A0239_2a Circuit Breaker 6 3A0239F Electrical Schematics Electrical Schematics 230V, 1 Phase, Basic HFR Module Schematic 3A0239F 7 Electrical Schematics 230V, 1 Phase, Loaded HFR Module Schematic 8 3A0239F Electrical Schematics 230V, 3 Phase, Basic HFR Module Schematic 3A0239F 9 Electrical Schematics 230V, 3 Phase, Basic VRM Module Schematic 10 3A0239F Electrical Schematics 230V, 3 Phase, Loaded HFR Module Schematic 3A0239F 11 Electrical Schematics 230V, 3 Phase, Loaded VRM Module Schematic 12 3A0239F Electrical Schematics 400V, 3 Phase, Basic HFR Module Schematic 3A0239F 13 Electrical Schematics 400V, 3 Phase, Basic VRM Module Schematic 14 3A0239F Electrical Schematics 400V, 3 Phase, Loaded HFR Module Schematic 3A0239F 15 Electrical Schematics 400V, 3 Phase, Loaded VRM Module Schematic 16 3A0239F Electrical Schematics 230V, 3 Phase, Loaded VPM Module Schematic 3A0239F GND 1L3 1 HARNESS 1L1 1L2 1L3 PG105 GND L3 L2 1L1 DISC-1 1 GND 1L1 1080 BLK 1080 1L2 1100 RED 1100 WHT 1120 1L3 1120 CB1 30A L1 331 L2 PG116 1L2 1L2 1L3 1L3 1160 1160 1180 1180 CB2 20A 1L3 1L3 PRIMARY HT B VOLUME HARNESS 1220 1220 1240 1240 1 GND 1L1 1 511 PG121 1L1 MCM B VOLUME L3 HARNESS CB3 15A TANK VOLUME HARNESS PG133 1L2 1L1 1340 1L2 1360 1340 1360 1340 MISC B VOLUME 1390 BR L1/P 1400 BL L2/N LINE 1360 755 1360 POWER FILTER CB5 5A 1 1340 POWER SUPPLY CAN SPLITTER 123466 121808 LOAD 1L1 GND 151 151 151 1L1 1L2 1L3 1L1 1L2 1L3 148 148 148 HARNESS 1L1 1L2 1L3 PG156 GND 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 1L2 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 L1 230V/ 3PH/ 50-60HZ 1L1 1580 BLK 1580 1L2 1600 RED 1600 WHT 1620 1L3 1620 CB10 30A L1 469 L2 1L1 1L2 1L2 1660 1660 1680 1680 MCM A VOLUME L3 HARNESS PG166 1L1 2 GND 2 649 PRIMARY HT A VOLUME CB9 20A HARNESS PG184 1L1 1L1 1L3 1L3 1840 1840 1860 1860 2 824 MISC A VOLUME CB6 5A 17 Electrical Schematics 400V, 3 Phase, Loaded, Non-CE, VPM Module Schematic 18 GND 1N 1L3 1 HARNESS 1L1 1N PG105 GND N L3 GND 1L1 1080 BLK 1080 1N 1100 WHT 1100 CB1A 63A L1 331 L2 PG116 1L2 1L2 1N 1N 1160 1160 1180 1180 CB2 20A 1N 1N PRIMARY HT B VOLUME HARNESS 1220 1220 1240 1240 1 GND 1L2 1 511 PG121 1L2 MCM B VOLUME L3 HARNESS CB3 15A TANK B VOLUME HARNESS PG133 1L2 1N 1L2 1340 1N 1360 1340 1360 1340 MISC B VOLUME 1390 BR L1/P 1400 BL L2/N LINE 1 755 1360 POWER FILTER CB5 5A 1360 1340 POWER SUPPLY CAN SPLITTER 123466 121808 LOAD L1 1L1 DISC-1 1 GND 151 151 151 1L2 1L3 1N 1L2 1L3 1N 148 148 148 HARNESS 1L3 1N PG156 GND 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 1L2 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 L2 400V/ 3PH/ 50-60HZ 1L3 1580 BLK 1580 1N 1600 WHT 1600 CB10A 63A L1 469 L2 PG166 1N MCM A VOLUME L3 HARNESS 1L2 2 GND 1L2 1660 1660 1N 1680 1680 2 649 PRIMARY HT A VOLUME CB9 20A HARNESS PG184 1L2 1L2 1N 1N 1840 1840 1860 1860 2 824 MISC A VOLUME CB6 5A 3A0239F Electrical Schematics 400V, 3 Phase, Loaded, CE approved, VPM Module Schematic 3A0239F GND 1N HARNESS POWER FILTER 1L1 1N 1L1 1081 1N 1101 L2/N LINE CB1A 63A L1/P BLK 1080 1100 WHT 1100 1L2 1N 1N L1 331 L2 PG116 1160 1160 1180 1180 CB2 20A 1N 1N PRIMARY HT B VOLUME HARNESS 1220 1220 1240 1240 1 GND 1L2 1 511 PG121 1L2 MCM B VOLUME L3 HARNESS GND 1L2 GND 1080 LOAD 1L3 1 PG105 GND N L3 CB3 15A TANK B VOLUME HARNESS PG133 1N 1340 1N 1360 1340 1340 1360 1340 1400 BL L2/N LINE MISC B VOLUME 1390 BR L1/P 1360 1 755 1360 POWER FILTER CB5 5A POWER SUPPLY CAN SPLITTER 123466 121808 LOAD 1L2 1L2 GND 151 151 151 1L3 1N 1L2 1L3 1N 148 148 148 HARNESS POWER FILTER 1L3 1N 1L3 1581 1N 1601 CB10A 63A L1/P L2/N GND 1L2 1L2 1N 1N PG156 GND 1L2 2 GND 1580 BLK 1580 1600 WHT 1600 LOAD L1 1L1 DISC-1 1 LINE 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 1L2 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 L2 400V/ 3PH/ 50-60HZ L1 469 L2 MCM A VOLUME L3 HARNESS PG166 1660 1660 1680 1680 2 649 PRIMARY HT A VOLUME CB9 20A HARNESS PG184 1L2 1L2 1N 1N 1840 1840 1860 1860 2 824 MISC A VOLUME CB6 5A 19 Parts Parts HFR Power Distribution Modules 400V, 3 Phase, Basic Module Shown 19 56 62 18, 48 56 4 9 5, 6 1 3 14 69 2 8 23 7 21 8 r_24C686_3A0239_2b 3 13 39 12 11 10 35 46 8 46 44 Circuit Breaker Detail for 400V, 3 Phase, Loaded Module 10 7 11 r_24C688_3A0239_4a 39 20 35 36 38 36 35 3A0239F Parts 1c 24 26 61 26 27 20 1a 27 r_24C680_3A0239_5a Parts Used on All HFR Modules Ref. 1 1a Part Description Qty. --ENCLOSURE 1 24D207 SUPPLY, power; 24 Vdc, 4A, 1 100W, 230 Vac 1b 196548 LABEL, caution 1 (on enclosure door) 1c 123718 FILTER 1 2 --PANEL, electrical 1 3 123396 NUT, flange, serrated; 3/8-16 4 4 117666 TERMINAL, ground 1 5 113783 SCREW, mach, pan hd 1 6 100985 WASHER, lock ext 1 7 16A647 RAIL, din, 17.7 in. 1 9 16A649 HARNESS, ground wire; 8 awg 1 10 123363 BLOCK, terminal, ground, 10mm 4 11 --LABEL, identification 1 12 24D217 HARNESS, wire,16 awg, ferrule 2 13 24D218 HARNESS, wire,16 awg, ferrule, 1 terminal ground 14 24D220 HARNESS, wire,18 awg, ring, 1 terminal, ground 3A0239F Ref. 24 25 26 27 29 61 69 25 29 r_24C680_3A0239_6a Part Description Qty. 122487 CABLE, CAN, male-female,1.5 m 1 123589 BUSHING, wire protector, 2 snap-in 111800 SCREW, cap, hex head 10 123679 BUSHING, wire protector; 3 1 3/8 OD 123590 PLUG, hole; 2 in. diameter 2 --BRACKET, support, electric 2 --LABEL, identification 1 Not shown. --- Not for sale. Replacement Danger and Warning labels, tags, and cards are available at no cost. 21 Parts Parts that Vary by HFR Module Use the following table to locate parts that vary by module. See Parts Used on All HFR Modules, page 21, for parts used on all HFR modules. Ref. Description 230V, 1 phase, basic 230V, 1 phase, loaded 8 SCREW, machine 103833(4) 103833(4) 103833(4) 103833(4) 103833(8) 103833(8) 18 SWITCH, disconnect 123969 123360 123969 123969 123969 123969 1 19 KNOB, operator disconnect 123967 123362 123967 123967 123967 123967 1 20 HARNESS, wire, MCM; 6/3 24C515 24C515 24C515 24C515 1 HARNESS, wire, MCM; 10/4 230V, 3 phase, basic 24C516 230V, 3 phase, loaded 400V, 3 phase, basic 4000V, 3 phase, loaded Qty. 24C516 - 1 21 FILTER, 55A, 3P 123785 123785 1 23 HARNESS, wire, 8 awg, ground 24D216 24D216 1 35 CIRCUIT, breaker, 2P, 5A 36 CIRCUIT, breaker, 2P, 15A 123350 123350 123350 2 38 CIRCUIT, breaker, 2P, 40A 123455 123455 123455 4 39 CIRCUIT, breaker, 2P, 63A 123668 1 40 CIRCUIT, breaker, 3P, 30A 41 BUSS BAR, 3P, 6 PIN, 115A 1 43 BUSS BAR, 3P, 18 PIN, 115A 1 44 BUSS BAR, 2P, 6 PIN, 115A 123310 (1) 45 BUSS BAR, 2P, 12 PIN, 115A 123474 46 CONNECTOR, lug, power, 115A 47 CAP, lug, power 48 SWITCH, disconnect, ph exp 100A 56 HARNESS, wire 6 awg, 14 awg 57 HARNESS, wire 6 awg 58 HARNESS, wire 4 awg, ferruled 59 HARNESS, wire, plug, tanks 62 HARNESS, wire, 6 awg, ferruled 72 LATCH, plug, 30A 123296 (1) 123296 (2) 123296 (1) 123296 (2) 123296 (1) 123296 (2) 123668 123668 123668 123302 123302 - 1 123310 (3) 1 123306 (2) 123306 (3) 123306 (3) 123306 (8) --- 1 123968 16A650 123968 16A650 1 2 16A694 (3) - 24D221 (4) 24D221 (3) 24D221 (6) - 24C517 24C517 24C517 2 16D536 2 24E823 2 16D536 24E823 24E823 Not shown. --- Not for sale. 22 3A0239F Parts VRM Power Distribution Modules 400V, 3 Phase, Basic Module Shown 19 57 56 55 18, 48 8, 49, 50 23 4 5, 6 2 56 3 14 69 1 21 23 7 21 8 3 13 12 39 35 11 10 8 9 r_24C687_3A0239_3a 46 Circuit Breaker Detail for 400V, 3 Phase, Loaded Module 46 44 10 7 11 39 3A0239F 35 36 38 36 35 39 r_24C689_3A0239_7a 23 Parts 63, 64, 65 24 26 1c 20 20 1a 27 28 27 26 25 29 Parts Used on All VRM Modules Ref. 1 1a Part Description Qty. --ENCLOSURE 1 24D207 SUPPLY, power; 24 Vdc, 4A, 1 100W, 230 Vac 1b 196548 LABEL, caution 1 (on enclosure door) 1c 123718 FILTER 1 2 --PANEL, electrical 1 3 123396 NUT, flange, serrated; 3/8-16 4 4 117666 TERMINAL, ground 1 5 113783 SCREW, mach, pan hd 1 6 100985 WASHER, lock ext 1 7 16A647 RAIL, din, 17.7 in. 1 9 16A649 HARNESS, ground wire; 8 awg 1 10 123363 BLOCK, terminal, ground, 10mm 4 11 --LABEL, identification 1 12 24D217 HARNESS, wire,16 awg, ferrule 2 13 24D218 HARNESS, wire,16 awg, ferrule, 1 terminal ground 14 24D220 HARNESS, wire,18 awg, ring, 1 terminal, ground 24 122487 CABLE, CAN, male-female; 2 1.5 m 25 123589 BUSHING, wire protector, 2 snap-in 24 r_24C683_3A0239_9a r_24C683_3A0239_8a Ref. 26 27 28 29 35 63 64 65 66 69 Part Description 111800 SCREW, cap, hex head 123679 BUSHING, wire protector; 1 3/8 OD 123398 PLUG, hole,1.5 in. diameter 123590 PLUG, hole; 2 in. diameter 123296 CIRCUIT, breaker, 2P, 5A 24C477 BRACE, wireway, divided 24C478 COVER, wireway 102040 NUT, lock, hex 124128 BUSHING, wire protector --LABEL, identification Qty. 10 3 2 2 2 1 1 2 1 1 Not shown. --- Not for sale. Replacement Danger and Warning labels, tags, and cards are available at no cost. 3A0239F Parts Parts that Vary by VRM Module Use the following table to locate parts that vary by module. See Parts Used on All VRM Modules, page 24, for parts used on all VRM modules. 230V,3 phase, basic 230V, 3 phase, loaded 400V, 3 phase, basic 400V, 3 phase, loaded 103833 (4) 103833 (4) 103833 (14) 103833 (12) - SWITCH, disconnect 123969 123360 123969 123969 1 19 KNOB, operator disconnect 123967 123362 123967 123967 1 20 HARNESS, wire, MCM; 6/3 24C515 24C515 2 Ref Description 8 SCREW, machine 18 HARNESS, wire, MCM; 10/4 24C516 24C516 Qty 2 21 FILTER, 55A, 3P 123785 123785 2 23 HARNESS, wire, 8 awg, ground 24D216 24D216 2 36 CIRCUIT, breaker, 2P, 15A 123350 123350 2 38 CIRCUIT, breaker, 2P, 40A 123455 123455 4 39 CIRCUIT, breaker, 2P, 63A 123668 2 40 CIRCUIT, breaker, 3P, 30A 123302 123302 2 42 BUSS BAR, 2P, 6 PIN, 115A 123308 123308 1 43 BUSS BAR, 3P, 12 PIN, 115A 123309 1 44 BUSS BAR, 2P, 6 PIN, 115A 46 CONNECTOR, lug, power, 115A 47 CAP, lug, power 48 SWITCH, disconnect, ph exp 100A 123968 49 BLOCK, power distribution, 1 pole, 4 wire 123489 1 50 COVER, power distribution block 123490 1 55 HARNESS, wire, 2 awg 16A646 (1) - 56 HARNESS, wire, 6 awg, 14 awg 16A650 4 57 HARNESS, wire, 6 awg 58 HARNESS, wire, 4 awg 59 HARNESS, wire, plug, tanks 62 HARNESS, wire, 4 awg; 23 in. 72 LATCH, plug, 30A 123668 123306 (3) 123306 (3) 123310 4 123306 (8) - 123311 1 16A646 (3) 123968 16A694 (3) 1 24C517 16D536 24E823 24D221 6 24C517 2 16D536 4 24E823 2 Not shown. 3A0239F 25 Parts VPM Power Distribution Modules 400V, 3 Phase, Basic Module Shown 1 23 18, 48 19 57 55 49, 50, 8 23 2 62 14 3 69 8 21 5, 6 4 13 9 57 8 3 ti18046a 7 12 46 Circuit Breaker Detail for 400V, 3 Phase, Loaded Module 44 39 8 35 36 37 35 39 10, 47 7 ti18047a 26 3A0239F Parts 25 26 1c 61 1b 1a 70 20 24 70 71 28 27 29 3A0239F ti18048a 71 27 Parts Parts Used on All VPM Modules Ref. 1 1a Part Description --ENCLOSURE 24D207 SUPPLY, power; 24Vdc, 4A, 100W, 230 Vac 1b 196548 LABEL, caution (on enclosure door) 1c 123718 FILTER 2 16A360 PANEL, electrical 3 123396 NUT, flange, serrated; 3/8-16 4 117666 TERMINAL, ground 5 113783 SCREW, mach, pan hd 6 100985 WASHER, lock ext 7 16A647 RAIL, din, 17.7 in. 8 103833 SCREW, mach, crbh 9 16A649 HARNESS, ground wire; 8 awg 10 123363 BLOCK, terminal, ground, 10mm 12 24D217 HARNESS, wire, 16 awg, ferrule 13 24D218 HARNESS, wire, 16 awg, ferrule, terminal ground 14 24D220 HARNESS, wire, 18 awg, ring, terminal, ground Qty 1 1 1 Ref. 18 19 24 25 26 27 28 29 35 36 37 46 61 69 71 Part 123969 123967 122487 123589 111800 123679 123398 123590 123296 123350 123298 123306 ----123652 1 1 4 1 1 1 1 6 1 5 Not shown. 2 --- Not for sale. 1 Description SWITCH, disconnect KNOB, operator disconnect CABLE, can, male-female, 1.5 m BUSHING, wire protector, snap-in SCREW, cap, hex hd BUSHING, wire protector, snap-in PLUG, hole, 1 1/2 diameter PLUG, hole, 2 in. diameter CIRCUIT, breaker, 2P, 5A CIRCUIT, breaker, 2P, 15A CIRCUIT, breaker, 2P, 20A CONNECTOR, lug, power, 115A BRACKET, support, electric LABEL, identification CABLE, can, male / female 3.5m Qty 1 1 1 4 10 6 6 4 2 1 2 3 2 1 1 Replacement Danger and Warning labels, tags, and cards are available at no cost. 1 Parts that Vary by VPM Module Use the following table to locate parts that vary by module. See Parts Used on All VPM Modules, page 28, for parts used on all VPM modules. Ref. Description 20 21 23 39 42 44 47 48 49 50 55 57 62 70 28 HARNESS, wire, MCM FILTER, 55A, 3P HARNESS, wire, 8 awg, ground CIRCUIT, breaker, 2P, 63A CIRCUIT, breaker, 3P, 30A BUSS BAR, 3P, 12 PIN, 115A BUSS BAR, 3P, 18 PIN, 115A BUSS BAR, 2P, 6 PIN, 115A CAP, lug, power (not shown) SWITCH, disconnect, ph exp 100A BLOCK, power distribution, 1 pole, 4 wire COVER, power distribution block HARNESS, wire, 2 awg HARNESS, wire, 6 awg HARNESS, wire, 4 awg, ferruled HARNESS, wire, 6 awg, ferruled HARNESS, wire, MCM 400V, 3 phase, non-CE 230V, 3 phase 24E624 24E625 123688 400v, 3 phase, CE 24E624 123785 24D216 123668 123302 123308 123309 123310 123310 123311 123968 123489 123490 16A646 16A694 123968 123489 123490 16A646 16A694 24D221 24E620 24E621 16D536 24E620 Qty. 1 2 2 2 2 1 1 2 1 1 1 1 1 6 3 4 1 3A0239F Parts 3A0239F 29 Graco Standard Warranty Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www.graco.com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505 30 3A0239F
