Download Durabrand DBTV2500 User's Manual

DBTV2500
SERVICE MANUAL
COLOR TELEVISION RECEIVER
ORIGINAL
MFR’S VERSION B
Design and specifications are subject to change without notice.
DBTV2500
SERVICE MANUAL
COLOR TELEVISION RECEIVER
REVISION 1
MFR’S VERSION D
MFR’S VERSION
IC101
B
OEC7044A
D
OEC7045A
Please file this revision with the original version.
Change of IC101
DIFFERENCES
MFR'S VERSION B
REF. NO.
IC101
PCB010
PART NO.
DESCRIPTION
MFR'S VERSION D
PART NO.
DESCRIPTION
I56F07044A IC
OEC7044A
I56F07045A
IC
OEC7045A
A3I058G01A MAIN PCB ASS'Y
TMX456A
A3I058G01B MAIN PCB ASS'Y
TMX456A
SPEC.NO.
M3I0-62G
O/R NO.
A073521
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
6. AVOID AN X-RAY
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
Safety is secured against an X-ray by considering about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage peripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathoderay tube.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
7. PERFORM A SAFETY CHECK AFTER
SERVICING
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
1. Unplug the plug from the AC outlet.
2. Remove the antenna terminal on TV and turn
on the TV.
3. Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note1] .
4. If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
A1-1
CONTENTS
SERVICING NOTICES ON CHECKING ......................................................................................................
HOW TO ORDER PARTS ...........................................................................................................................
IMPORTANT ................................................................................................................................................
CONTENTS .................................................................................................................................................
GENERAL SPECIFICATIONS ....................................................................................................................
DISASSEMBLY INSTRUCTIONS ...............................................................................................................
SERVICE MODE LIST .................................................................................................................................
CONFIRMATION OF USING HOURS .........................................................................................................
NOTE FOR THE REPLACING OF MEMORY IC ........................................................................................
ELECTRICAL ADJUSTMENTS ..................................................................................................................
MAJOR COMPONENTS LOCATION GUIDE .............................................................................................
BLOCK DIAGRAM ......................................................................................................................................
PRINTED CIRCUIT BOARDS
MAIN/CRT...........................................................................................................................................
SCHEMATIC DIAGRAMS
MICON/TUNER ..................................................................................................................................
CHROMA ...........................................................................................................................................
DEFLECTION/CRT ............................................................................................................................
POWER .............................................................................................................................................
SOUND ..............................................................................................................................................
WAVEFORMS .............................................................................................................................................
MECHANICAL EXPLODED VIEW ..............................................................................................................
MECHANICAL REPLACEMENT PARTS LIST ..........................................................................................
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................
A2-1
A1-1
A1-1
A1-1
A2-1
A3-1~A3-4
B-1, B-2
C-1
C-1
C-1
D1-1~D2-1
D3-1
E-1, E-2
F-1~F-4
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
G-9, G-10
H-1, H-2
I-1
J1-1
J2-1, J2-2
GENERAL SPECIFICATIONS
G-1.Outline of the Product
25
inch( 626 mmV):Measured diagonally
Color CRT
100 degree deflection
G-2.Broadcasting System
US
G-3.Color System
System
M
NTSC
PAL
SECAM or Monochrome signal
G-4.NTSC Playback(PAL 60Hz)
Yes
No
G-5.NTSC 3.58+4.43/PAL60Hz
Yes
No
G-6.Antenna Input Impedance
VHF/UHF 75 ohm unbalanced
G-7.Tuner and Receiving
Contactless Electric tuner
channel Tuner
Oscar(W/O HYPER)
France CATV)
Receiving channel
(USA)
2-69 ,
Tuning System
Frequency syn.
4A ,
A-5~A-1 ,
A~I ,
Voltage syn.
1Tuner System
2Tuner System
Oscar(W/ HYPER)
Others
J~W ,
W+1~W+84
Others
G-8.Preset Channel
-- channels
G-9.Intermediate Frequency
Picture(fP)
Sound (fS)
fP-fS
45.75 MHz
41.25 MHz
4.50 MHz
G-10.Stereo/Dual TV Sound
Yes( NICAM
GERMAN
G-11.Tuner Sound Muting
120
G-13.Power Consumption:
G-16.Cabinet Material
Cabinet Front:
Back Panel:
504
Net :
Gross:
mm(D)
27
29
MHz
MHz
MHz
JAPAN)
No
No
V
AC 50Hz
115 W at AC
W at DC
8 W at AC
- kWh / Year
Stand by:
Per Year:
G-15.Weight(Approx.)
USA
Yes
G-12.Power Source
G-14.Dimensions(Approx.)
618 mm(W)
MHz
MHz
MHz
525
120
120
V
V
V
AC 60Hz
60
Hz
60
Hz
mm(H)
kg ( 59.9 lbs)
kg ( 64.3 lbs)
PS
ABS
94HB
94V2
94V0
DECABROM
NON-DECA
PS
ABS
94HB
94V2
94V0
DECABROM
NON-DECA
A3- 1
GENERAL SPECIFICATIONS
G-17.Protector:
Power Fuse
G-18.Regulation
Safety
UL
BS
SEMKO
NOM
Radiation
FCC
SABA
CNS
X-Radiation
PTB
G-19.Temperature
Operation
Storage
CSA
NF
NZ
AS3159
SAA
NEMKO
HOMOLO
DENTORI
SI
FEMKO
SABS
UNE
CE
DEMKO
CNS
GOST
SEV
IEC65
SISIR
NONE
DOC
SI
CISPR13
FTZ
NF
DENTORI
PTT
NZ
AS/NZS
CE
HOMOLO
NONE
SEV
UNE
DHHS
HWC
DENTORI
NONE
5
-20
˚C~
˚C~
40 ˚C
60 ˚C
G-20.Operating Humidity
Less than
G-21.Clock and Timer
Sleep Timer
On/Off Timer
Wake Up Timer
Yes Max
Yes
Yes
80
%RH
120
Min.(
Programs
Programs
10
Min. Step)
No
No
No
G-22.Timer back up Time
More than
-- Minutes (at Power Off Mode)
G-23.Terminals
VHF/UHF Antenna Input
Front Video Input
(RCA
Rear Video Input
(RCA
Rear Video Output
(RCA
Front Audio Input
(RCA
Rear Audio Input
(RCA
Rear Audio Output
(RCA
21 Pin
Head Phone Jack(ø3.5)
Diversity
Din Type
F-Type
France Type
ø8.3)
ø8.3)
ø8.3)
ø8.3)
ø8.3)
ø8.3)
DC Jack(Center +)
AC Outlet
S Input(Front)
Ear Phone Jack(ø3.5)
Ext Speaker
S Input(Rear)
G-24.Indicator
(
Power
)
(
Stand By
)
(
On Timer
)
G-25.Display
On Screen Display
Menu
Clock Set( 12H 24H)
Hotel Lock
Sound 1/2
Guide CH Set
CATV
Control Level
Sound
Color
Tuning
Balance
Stereo,Audio Output,Bilingual
Stereo,Audio Output, SAP
Stereo,Audio Output
AV
Channel
Sleep Timer
Sound Mute
A3- 2
NONE
System Selec
Area Code
NICAM Auto Off
Audio
Pin Code Registration
Brightness
Tint(NTSC Only)
Bass
Back Light
Picture Menu
Mid Night Theater
GAME
Clock
Pin Code
On/Off Timer
CH Tuning
Picture
Language
V-Chip
Contrast
Sharpness
Treble
Hotel Lock
GENERAL SPECIFICATIONS
G-26.OSD Language
Eng
Ger
Fre
Spa
Ita
Por
Jpn
OSD Language Setting
Eng
Ger
Fre
Spa
Ita
Por
Jpn
Not Applicable
G-27.Speaker
P os i t i on
Front
Side
Bottom
Size
1.5 x 2.7 inches
Imp.
4
ohm x
2
pcs
Power
Max
075 + 0.75 W
10%
0.5 + 0.5 W (Typical)
G-28.EXT Speaker
Yes
-- W
Imp
-ohm
G-29.Carton
Master Carton:
Need
No Need
Content:
---- Set
Material:
---- / ---Corrugated Carton
Dimensions:
---- mm(W)
---- mm(D)
---- mm(H)
Description of Origin
Yes
No
Gift Box
Material
Double/Brown Corrugated Carton ( with Photo Label)
Double/White Corrugated Carton ( with Photo Label)
Double Full Color Carton W/Photo
Dimensions:
689 mm(W)
577 mm(D)
620 mm(H)
Design:
As Per BUYER 's
Description of Origin:
Yes
No
Drop Test
Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height
25cm
31cm
46cm
62cm
80cm
Container Stuffing:
204 Sets / 40' container
G-30.Accessories
Owner's Manual ( W/Guarantee Card) [ English/French ]
AC Plug Adapter
Channel Film
Battery (UM- 4 x 2 )
Remote Control Unit
Safety Tip
Toll Free Insert Sheet
Guarantee Card
Audio-Video Cord (RCA)
Registration Card
Warning Sheet
Quick Set-Up Sheet
Schematic Diagram
Information Sheet
U/V Mixer
75 ohm Coaxial Cable ( Single Shield
Double Shield)
300 ohm to 75 ohm VHF Antenna Adaptor
21pin Cable
Car Cord
Rod Antenna
One Pole
Two Pole ( F-Type
Din Type
France Type)
Loop Antenna
( F-Type
Din Type
France Type)
G-31.Other Features
Auto Degauss
Auto Search
Full OSD
Auto Shut Off
CH Allocation
Premiere
Canal+
SAP
Comb Filter
CATV(181CH)
Channel Lock
Auto CH Memory
Anti-Theft
Just Clock Function
Hotel Lock
Rental
Game Position
Fastext
Unitext
TopText
Closed Caption
Picture Menu
Mid Night Theater
V-Chip
A3- 3
GENERAL SPECIFICATIONS
G-32.Switch
Front
Power(Tact)
System Select
Main Power SW
Channel Up/Reset
Channel Down/Enter
Sub Power
AC/DC
Degauss
TV/CATV Selector
Main Power SW
Volume Up/Set Up
Volume Down/Set Down
Menu:Vol UP + Vol Down
Rear
G-33.Magnetic Field
BV :
BH :
BV :
BH :
+0.45G
0.18G
-0.15G
0.15G
BV
BH
BV
BH
:
:
:
:
+0.35G
0.30G
-0.25G
0.15G
G-34.Remote Control Unit:
RC- 74
Glow in Dark Remocon
Yes
Power Source:
D.C
3 V
Battery UM - 4 x 2
Total 26 Key
Power
Quick View
Stand By
Status
0
Time Select
1
Time Set
2
Muting
3
CH Skip
4
CH1/CH2
5
Channel
6
Text/Mix/TV
7
Display Cancel
8
Initial
9
Store
10
Reveal
11
Sleep
12
Aft/Skip
1
Preset
2
5.5/6.5MHz
0/10
Auto Memory
Tone 1/2
Auto
Info
Call
Mono/Auto
Reset
TV/Caption/Text
Menu
Expand
Enter
Red
Add
Cyan
Delete
Normal
Yellow
Color System
Random
Wide Selecy
Tuning Up/Time Text
Auto Wide On/Off
Tuning Down/Reset
Picture Position
Navi
Direct Change/Auto Search
Picture Menu
Mid Night Theater
A3- 4
BV
BH
BV
BH
:
:
:
:
+0.25G
0.30G
-0.50G
0.30G
No
TV/AV
Bar Select
PAL/SECAM
Volume Up
Volume Down
CH Call
CH Down
CH Up
CH Down/Page Down
CH Up/Page Up
Page +/Program
F/T/B
Hold
List
Rotate
Browse
Std/Auto
Memory
Band Select
Search
Clock/Program
Clock/Set
Ch Set
Set +
Set Green
Nicam/Mono
Tone A/B
FM Transmitter
Back Light
Audio Select
DISASSEMBLY INSTRUCTIONS
3. After one side is removed, pull in the opposite direction to
remove the other.
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage.
* Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a small
amount of alcohol. (Refer to Fig. 1-3.)
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
Location of Anode Cap
GND on the CRT
Fig. 1-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
CRT
Screwdriver
Support
Alligator Clip
GND on the CRT
Fig. 1-1
2. Flip up the sides of the Rubber Cap in the direction of the
arrow and remove one side of the support.
(Refer to Fig. 1-2.)
Rubber Cap
Fig. 1-4
CRT
Support
Fig. 1-2
B-1
DISASSEMBLY INSTRUCTIONS
4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 1-5.
CRT
Support
Fig. 1-5
5. Confirm that the Support is securely connected.
6. Put on the Rubber Cap without moving any parts.
2. REMOVAL OF DEFLECTION YOKE
(Refer to Fig. 2-1)
1. Loosen the screw 1.
2. Remove the Convergence • Purity Magnet in the
direction of arrow (A).
3. Loosen the screw 2.
4. Remove the 3 Wedges.
5. Remove the Deflection Yoke in the direction of arrow
(B).
2
Wedge
1
(B)
(A)
Convergence •
Purity Magnet
Deflection Yoke
Wedge
Fig. 2-1
INSTALLATION
Install new Deflection Yoke in reverse steps of REMOVAL.
NOTE
After adjusting the purity and the convergence, fix the
screw 2 and lock the wedges.
B-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.
Set Key
Remocon Key
VOL. (-) MIN
0
Releasing of V-CHIP PASSWORD.
Operations
VOL. (-) MIN
1
Initialization of the factory.
NOTE: Do not use this for the normal servicing.
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF USING HOURS".
VOL. (-) MIN
6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".
VOL. (-) MIN
8
Writing of EEPROM initial data.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN
9
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
CONFIRMATION OF USING HOURS
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
ADDRESS
1. Set the VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel
button (6) on the remote control for more than 1 second.
3. After the confirmation of using hours, turn off the power.
INIT
DATA
00
83
0010
CRT ON
Initial setting content of MEMORY IC.
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
FIG. 1
NOTE FOR THE REPLACING OF MEMORY IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
ADDRESS
INI
00
INI
01
INI
02
INI
03
INI
04
INI
05
INI
06
INI
07
INI
08
INI
09
INI
0A
DATA
A0
01
A2
09
02
63
24
18
A1
21
44
Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
3. ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using SET + or - until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
C-1
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL
ADJUSTMENTS
2. BASIC ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
1. Receive an 80dB monoscope pattern.
2. Connect the digital voltmeter to TP001.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (02) on the remote control to
select "RF DELAY".
4. Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 1.80 ± 0.05V.
2-1: RF AGC DELAY
CAUTION
• Use an isolation transformer when performing any
service on this chassis.
• Before removing the anode cap, discharge electricity
because it contains high voltage.
• When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
Inferior silicon grease can damage IC's and transistors.
• When replacing IC's and transistors, use only specified
silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
2-2: CUT OFF
Prepare the following measurement tools for electrical
adjustments.
1. Adjust the unit to the following settings.
R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
B.BIAS=64, BRIGHTNESS=126, CONTRAST=100.
2. Place the set with Aging Test for more than 15 minutes.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "CUT OFF".
4. Adjust the Screen Volume until a dim raster is obtained.
1. Synchro Scope
2. Digital Voltmeter
2-3: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
On-Screen Display Adjustment
1. Place the set with Aging Test for more than 10 minutes.
2. Receive the with 100% signal from the pattern generator.
3. Using the remote control, set the brightness and contrast to
normal position.
4. Activate the adjustment mode display of Fig. 1-1 and press
the channel button (10) on the remote control to select
"R.BIAS".
5. Using the VOL. UP/DOWN button on the remote control,
adjust the R.BIAS.
6. Press the CH. UP/DOWN button on the remote control to
select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".
7. Using the VOL. UP/DOWN button on the remote control,
adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS.
8. Perform the above adjustments 6 and 7 until the white
color is looked like a white.
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control for more than
1 second to appear the adjustment mode on the screen
as shown in Fig. 1-1.
TV
00 OSD
15
Fig. 1-1
2-4: FOCUS
2. Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
3. Press the MENU button on the remote control to end
the adjustments.
NO.
00
01
02
03
04
05
06
07
08
09
10
11
12
FUNCTION
OSD H
CUT OFF
RF DELAY
VIF VCO
H VCO
H PHASE
V SIZE
V SHIFT
R DRIVE
B DRIVE
R BIAS
G BIAS
B BIAS
NO.
13
14
15
16
17
18
19
20
21
22
23
24
1. Receive the monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.
2-5: SUB TINT/SUB COLOR
1. Receive the color bar pattern.
2. Connect the synchro scope to TP023.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "TINT".
4. Press the VOL. UP/DOWN button on the remote control
until the waveform becomes as shown in Fig. 2-1.
5. Connect the synchro scope to TP022.
6. Press the CH DOWN button once to set to "COLOR"
mode.
7. Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 110% of the white
level. (Refer to Fig. 2-2)
FUNCTION
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
FM LEVEL
LEVEL
SEPARATION 1
SEPARATION 2
TEST MONO
TEST STEREO
X-RAY TEST
Fig. 1-2
D1-1
ELECTRICAL ADJUSTMENTS
TV
Fig. 2-1
00 OSD
A
0%
15
B
Fig. 2-3
2-9: OSD HORIZONTAL
1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote
control until the difference of A and B becomes
minimum. (Refer to Fig. 2-3)
110%
100%
2-10: VERTICAL VCO
Fig. 2-2
1. Place the set with Aging Test for more than 15 minutes.
2. Receive an 80dB monoscope pattern.
3. Connect the digital voltmeter between the pin 5 of
CP601.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "VIF VCO".
5. Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.5V.
2-6: HORIZONTAL PHASE
1. Receive the center cross signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (05) on the remote control to
select "H.PHASE".
4. Press the VOL. UP/DOWN button on the remote
control until the SHIFT quantity of the OVER SCAN on
right and left becomes minimum.
2-11: SUB BRIGHTNESS
1. Receive the black pattern*. (RF Input)
2. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "BRIGHTNESS".
3. Press the VOL. UP/DOWN button on the remote control
unit the screen begin to shine.
2-7: VERTICAL SIZE
NOTE: Adjust after performing adjustments in section 2-6
1. Receive the crosshatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select "V.SIZE".
4. Press the VOL. UP/DOWN button on the remote control
until the rectangle on the center of the screen becomes
square.
5. Receive a broadcast and check if the picture is normal.
2-12: SUB CONTRAST
1. Receive the color bar pattern.
2. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (14) on the remote control to
select "CONTRAST".
3. Press the VOL. UP/DOWN button on the remote control
unit the nit for more than 200 nit.
2-8: VERTICAL SHIFT
NOTE: Adjust after performing adjustments in section 2-7
1. Receive the crosshatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1
and press the channel button (07) on the remote control to
select "V.SHIFT".
4. Press the VOL. UP/DOWN button on the remote
control until the horizontal line becomes fit to the notch
of the shadow mask.
D1-2
ELECTRICAL ADJUSTMENTS
3-3: STATIC CONVERGENCE
3. PURITY AND CONVERGENCE
ADJUSTMENTS
NOTE
Adjust after performing adjustments in section 3-2.
NOTE
1. Receive the crosshatch pattern from the color bar
generator.
2. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
1. Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.
2. Place the CRT surface facing east or west to reduce the
terrestrial magnetism.
3. Turn ON the unit and demagnetize with a Degauss Coil.
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
1. Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.
2. Receive the green raster pattern from the color bar
generator.
3. Slide the deflection yoke until it touches the funnel
side of the CRT.
4. Adjust center of screen to green, with red and blue on the
sides, using the pair of purity magnets.
5. Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
7. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
8. Adjust the crosshatch pattern to change to white
by repeating steps 6 and 7.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1. Adjust the differences around the screen by moving
the deflection yoke upward/downward and right/left.
(Refer to Fig. 3-2-a)
2. Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.
(Refer to Fig. 3-2-b)
RGB
R
G
B
RGB
R
G
B
3-2: PURITY
UPWARD/DOWNWARD SLANT
NOTE
RIGHT/LEFT SLANT
Fig. 3-2-a
Adjust after performing adjustments in section 3-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide.
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw.
WEDGE
WEDGE
WEDGE
DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW
PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1
D2-1
WEDGE POSITION
Fig. 3-2-b
MAJOR COMPONENTS LOCATION GUIDE
TU001
FB401
TP001
CP601
FOCUS VOLUME
SCREEN VOLUME
MAIN PCB
TP023
TP024
J801
TP022
CRT PCB
D3-1
BLOCK DIAGRAM
Q351
MUTE SW.
SDA
SCL
AGC
VOL UP
IF
TU001
CH UP
11
5
4
1
CHROMA IC
IC601 M61203BFP
X602
3.579545MHz
IC351 AN7523
32 X' TAL
AUDIO OUT 50
MICON IC
IC101 OEC7044A
CH DOWN
CF601
5
64 VIF IN (1)
AUDIO MUTE
1
26 KEY2
POWER
OS101
Q606
VIF IN (2)
R OUT 14
GREEN G 41
28 G IN
G OUT 15
BLUE B 40
20 B IN
B OUT 16
27 FAST BLK
REG OUT 41
H. SYNC
1
12 INV FBP OUT
3
V. SYNC
2
29 V PULSE OUT
SCL1 34
5 SCL
SDA1 32
10 SDA
RESET 25
5
20 XOUT
Q101
Q501
X_RAY_TEST 30
GREEN OUT
Q603
Q802
REG.
FBP IN
6
Q608
CUT OFF
START UP
19
VCC
H OUT 7
Q402
VREG VCC 55
6
MEMORY IC
SDA SCL IC199
S-24C02BDP-1A
17 V OUT
H. DRIVE
Q401
H. OUTPUT
X-RAY TEST SW
V-OUT IC
IC401 LA78041
POWER REG. IC
IC501
STR30110
4
Q803
42 MCU RESET
X101
8MHz
POWER
RED OUT
BLUE OUT
2
19 XIN
P. CON+15V
Q801
30 R IN
36 POWER
REG.
REG OUT 33
RED R 42
BLANK BL 39
10 REMOCON
1
SP351
4
40 Y SW OUT
CVIN 17
27 KEY1
2
SOUND IC
9
SAW FILTER
VOL DOWN
6
62 RF AGC OUT
PUMP UP
DEGAUSS COIL
L502
3
D501~D504
AMP
+
Q403
7
5
6
6
8
B
G
R
F
9
CRT
Heater
VCC
X-RAY TEST SW.
11
10
2
RECTIFIER
+B
RY101
IC402
KIA7805API
1
4
2
3
P. CON+5V
REG IC
1
DY
3
FB401
D127
L501
3
1
4
P. CON+5V
D404
5
2
9
1
F
5
S
10
HV
3
F501
AC IN
E-1
E-2
R422
C448
R445_1
W018
R409
W017
D411
W020
C401
R421_1
C405
C434
W015
W021
R405
R408
R401
Q401
W006
C443
D501
C503
Q402
C446
W079
D502
D503
C440
C439
C427
C418
R418
C417_1
R446
W104
W801
C504
W085
W815
D504
D125
TH501
C132_1
W061
W820
C646
R643
W095
W097
D601
R623
D607
W023
W802
W028
W027
W026
C118
W093
C635
R647
C621
TP022
C115
C501
R802
R804
CP
80
1_
1
W078
W030
W031
W025
W024
C645
C638
C622
X602
L605
R501_1
CP501
R803
R805
R807
01
J8
CC
2
FH501
F501
L801
C121
C128
D614
D101
W070
C122
C130
W040
C609
C123
W073
C613_1
W032
W069
C124
C640
D604
Q608
W034
R644
C637
C601
W068
W038
W099
W035
S105X
W043
W067
L101
R135
C119
00
W838
*
W045
W044
C610
D615
C654
D616
C612
C607
C603
6.3A125V
D103
C444
C437
W103
W060
R416
C422
W098
W055
W047
W046
W058
W051
W052
C627
Q802
C619_1
C606
SW105
W003
C507
C430
D403
R434_1
D602
R632
W063
L607
W839
C614
S802X
W033
C644
C605
C632
R618
C623
C651
W806
FH502
CP803B
R815
S106X
W891
C416
C435
C433
R404
W022
W005
W090
C414
C352
C357_1
W814
W048
C604
C129
RY101
C647
L406
R424
R507_1
R410
1
C519
C506_1
W835
D609
W834
R443_1
Q801
W828
SW103
SW104
SW101
W014
C353_1
W823
CP806
D610
SW102
D612
X101_1
C802_1
W029
L603
D104
W011
W071
W041
S809Y
T401_1
*
W897
W088
CC004
W819
C125
S803X
R407_2
D404
C412
TP024
TP023
Q603
R640
D126
W810
W829
W050
W042
S803Y
W812
W108
IC401
R655
C133
R806
S105Y
Q501
IC199
IC402
W092
Q101
C625
CF601
C661
C639
Q606
R417
R502
*
CP802B
C630
W083
C002
D001
W813
W004
R412
R427
HS401
CP401_1
W831
W817
D617
CP351_1
Q403
R506
W007
D127
S801X
C351
Q351
R177
S801Y
C359_1
15
D408
C004
D422
C404
Q803
S106Y
W082
C003
W066
W818
F-2
F-1
D611
W039
W059
W824
R448_1
IC351_1
D608
S104X
C631
W805
C624
D410
R001
R428_
D402
R508
D407
R5
R503
W074
S104Y
IC501
W019
D401
CP502
L501
CF603
CF604
HS501
R002
D605
R429_1
W010
TP001
TU001
D603
W837
S809X
S802Y
C636
L601
R509
CP803A
TP501
W049
CP601
D405
CP802A
C
C
00
6
PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE
FB401
OS101
F-3
R630
R006
R007
R606
R406
C411
R420 R419
C642
R611
R615
1
R621
17
49
R622
IC601
C618_1 C626
C616
R633
C643
33
R609
R635
R646
R122 R124
R104
R608
R641
R642
R634
R639
R116
R120 R121
R638
R612
R354
R102
R103
R123
C113
R355 R358
R356
R111
C116
C117
R106
R105
R107
C114
IC101
R636
R119
R504
R505
C801
R816
C806
R814
C805
R811
C804
R809
R813
C699
R624
R128
R631
R620 R627
R114
R625
R619
R614
R605 R613
R602 R604
R601
R626
R616 R617
R110
R115
C120
R130
R129
R113 R126
R112
R131
R117
R101
PRINTED CIRCUIT BOARDS
MAIN/CRT (CHIP MOUNTED PARTS)
SOLDER SIDE
C634_1
R603
F-4
A
B
C
D
E
F
G
H
MICON/TUNER SCHEMATIC DIAGRAM
(MAIN PCB)
8
1.3
NC
6.2
NC
4.6
5.0
5.0
NC
5.0
0
NC
30.0
0
NC
13
12
2
1 AGC
3 ADRES
4 SCL
6 V.S
10
8
9 BTL
15
11 IF
0
14
ATC001
NXC0032-010010
5 SDA
NJH3021U268
ACCESORY
7 BPL
TU001
8
TM101
R25-1127
TP001
C003
C002
6.3V 470 YK
HZ30-3L
D001
C004
P_CON+5V
FROM POWER
GND
270
68K 1/2W
270
R007
+B
68K1/2W
R002
R006
3 GND
2 B+
7
50V4.7 KA
R001
S809X
0
4.7
4.7
1 Vout
OS101
PIC-28143SY-2
0.022 M
FROM DEFLECTION/CRT
7
FROM/TO CHROMA
AGC
16V10 KA
6
I2C_OFF
VD
HD
0
NC
4.9
R130
C122
C121
50V 1 KA
3.0
1K
200P CH
C120
0.001 Y
C124
P24
SDA2
P25/ON_TIMER
AD1/X_RAY_TEST
AVCC
X-RAY
HLF
AD4/AFT
V.HOLD
AD5/KEY1
11
36
35
34
0
NC
TO SOUND
AUDIO_MUTE
4.9
C117
0
NC
270P B
R105
5.0
4.7K
C116
TO POWER
0
NC
270P B
R106
0
4.7K
R107
0
0
W812
0
R112
4.9
4.9
VCC
3
4.1
AT+5V
R119
RESET
1K
0.68 TF
23
VSS
22
0
MTZJ6.8B
C129
OSC2
21
X101_1
CST8.00MTW
2.7K
24
Xout
D103
AFT
2.2K
C114
10P CH
3.6
R135
19
OSC1
20
1
Xin
2
3
4.2
MTZJ6.8B
2.2K
R113
1
3.7
D101
4.9
0.01 Y
RESET
X-RAY
FROM CHROMA
50V0.1
KA
C125
CNVSS
25
0
X-RAY_TEST
16.0
X-RAY TEST SW
Q101
DTC114TS
3.2
C115
AD6/KEY2
4
POWER
FROM/TO DEFLECTION/CRT
L101
3.3uH
0.001 B
CVIN
4.7K
SDA
POWER
10K
26
R129
50V 0.1 KA
17
3.4
Y_VIDEO
C130
SDA1
SCL
4.9
2
18
SYNC
3
0.8
P23/SYNC
5
GND
1M
FROM CHROMA
12
0
NC
13
47K
14
3.9
15
MTZJ6.8B
16
D104
R115
4
33
SCL2
32
INT1/REMOCON
31
SCL1
30
INT2/P.FAIL
29
4.8
28
4.8
10K
R124
0
NC
2.2K
42
41
0
NC
27
R114
P10/DEGAUSS_H
OSD_BLK
R104
P05/(Center_SP)
9
0
P22/POWER
10
C128
0.01 Y
0
OSD_B
4.7K
R120
0
2.2K
P04
P21/AV1
OSD_G
4.7K
R121
0
4.7K
10K
0
OSD_R
R103
P03/(Surround)
P20/AV2
40
2
P02/AUDIO MUTE
39
OUT1/BLANK BL
4.7K
R122
2.2K
0
BLUE B
0
R102
47K
P01/I2C_OFF
0
R123
38
R111
P00/EXT MUTE
GREEN G
3
37
R117
47K
5
3
4.9
P51/V.SYNC
4
R116
0
5
1K
R110
4
RED R
6
4.9
P50/H.SYNC
7
4.9
1
MICON IC
IC101
OEC7044A
8
R131
6
47
C123
IF
C113
10P CH
4.9
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
A
G-1
B
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
C
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
D
ARE
2
R128
CH UP
SW101
SKHVBED010
560
25"
25"
CH DOWN
SW102
SKHVBED010
2.7K
VOL UP
SW103
SKHVBED010
R126
560
25"
1
0
POWER
SW105
SKHVBED010
2
0
R101
25" VOL DOWN
SW104
SKHVBED010
0
VCC
MODE
3
0
8
25"
4
E1
E2
VSS
6.3V 470 YK
5.0
7
IC199
0
6
E0
5.0
5
SCL
5.0
SDA
0.68 TF
C118
MEMORY IC
S-24C02BDP-11
C119
2
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
E
CAUTION: DIGITAL TRANSISTOR
F
TUNER VIDEO SIGNAL
R.SIGNAL
G.SIGNAL
B.SIGNAL
DEFLECTION SIGNAL
G
PCB010
TMX456
1
H
G-2
A
B
C
D
E
F
G
H
CHROMA SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
TO MICON/TUNER
SYNC
Y_VIDEO
FROM POWER
8.2
KA
C619_1
50V 1 KA
C622 0.015 M
C625
8.2K
R633
C627
7
P_CON+15V
REG.
Q606
2SD734
8.8
50V 1 KA
100
10V 47 KA
C635
33K
R636
C644
W828
R635
CF604
EFCT4R5MW5
10V100 YK
R622
L607
R623
120 1/4W
FROM POWER
7
15.0
50V 3.3
S802Y S802X
RESET
C631
470P B
7
6
10.6
5.5
15uH
4.8
REG.
Q603
2SD734
120
AT+5V
C616
X602
29
28
27
26
30
31
32
CHROMA APC FILTER
TV/Y IN
VIDEO/CHROMA GND
5v REG
Y SW OUT
R642
50V4.7 NA
D605
100K
11E1-EIC
5
C610
POWER ON CONT
R OUT
3.5
4.9
G OUT
4.9
11
12
25
24
23
22
21
ABCL
C613_1
1 TF
P_CON+5V
R641
V_FEEDBACK
20
20K
19
INV FBP OUT
4.9
15
16
4.0 4.0
4.8
FROM/TO DEFLECTION/CRT
MTZJ6.2B
2.5
0
8.2
18
AFC FILTER
14
5.6
D614
8.2
17
SDA
13
5.0
C645
16V 47 YK
4.5
D615
MTZJ6.2B
C654
0.022 F
4
R644
V_OUT
100 1/4W
D616
10
10V470 YK
0
12
0
NC
5.0
C612
0
11
MTZJ6.2B
GND
13
9
H_OUT
H_SYNC
D611
MTZJ12B
R627 100
B.OUT
G.OUT
R631 100
D603
D604
CUT OFF
Q608
2SA1015Y
0.1
50V10 KA
R620
C609
330
R616
1SS133 1SS133
CLAMP
0.8
0
1K
2.7K
R608
D612
MTZJ12B
2.2K
R.OUT
R617 2.7K
GND
HD
3
R630 100
R625
0.01 Y
8
2.2K
6.2
10
R619
6.2
9
MTZJ12B
2.2K
4.9
3.579545MHz 15P CH
0.001 Y
C643
C630
MCU RESET
8
C607
C651
7
C603
50V 1 KA
C639
10uH
2.7
6
B IN
STRAT UP Vcc
D610
R614
IF
6.3V 470 YK
R603
AGC
1.5K
1.2uH
C640 16V47 YK
C601
L601
AFT
5.0
5
R605
4.7K
5.0
C634_1
0.01 B
L603
2.7K
1uH
R621
L605
FROM/TO MICON/TUNER
4
3
R604 100
2
1.5
3
5.7V REG OUT(FOR CPU)
Hi Vcc
49
50
51
52
1
H OUT
2
RF AGC FILTER
DEF
3
RF AGC OUT
W837
4
QIF IN
2.7K
5
50V 0.1 KA
1.8
CHROMA IC
IC601
M61203BFP
17 V OUT
16 B OUT
64 VIF IN
1 VIF IN
R601
SAW FILTER
CF601
SAF45MFY220ZR
2.9
V RAMP FEEDBACK
1K
C606
AFT OUT
R602
10K
0
7.3
V RAMP CAP
FBP IN
1.8
FAST BLK
6
12K
C638
0
5.0
VIDEO CHROMA Vcc
R626 10K
0.001 Y
R606
4
2.9
VIF GND
100
C626
VIF VIDEO OUT
R646
2.6
0
SPOT KILLER
C661 0.01 Y
3.5
G OUT
fsc OUT
H VCO F/B
3.2
W819
V PULSE OUT
R638 6.8K
50V 0.22 YK
SCL
0
0.01 B
34 EXT C in
33 8.7V REG OUT
32 X’TAL
31 ACL/ABCL
R IN
VIF APC FILTER
0.01 Y
0
VREG Vcc
R624 2K
C618_1
2.6
46 SW REG CONT
47 LIMITER IN
48 IF AGC
49 QIF OUT
50 AUDIO OUT
R613
C621
22P CH
470 50V 0.47 KA
3.0
10V 2200 YK
R609
C605
D602
D601
S106Y
1SS133
MTZJ8.2B
C624
9.2
VIF VCO F/B
C637
0.01 Y
10M1/4W
FM DIRECT OUT
470P B
C699
0.01 Y
R618
3.1
VIF Vcc
C632 50V 2.2 KA
EXT AUDIO IN
53
R632
120 1/2W
5
3.8
54
3.2
55
C642 0.001 Y
C623 0.0033 M
AUDIO BYPASS
56
2.3
57
C604 50V 1 KA
58
5.6K
2.9 3.3 2.0 8.8
36
35
34
33
59
3.0
AUDIO_OUT
60
2.3
61
R612
10K
62
5
R634
10K
R611
63
GND
0
2.9 2.3
48
47
46
64
TO SOUND
D607
1SS133
0
0
8.2
8.2 3.9 4.8 5.5 3.4 0 NC
45
44
43
42
41
40
39
38
37
INTELLIGENT MONI
W805
6
0.01 Y
C614 0.01 Y
1.8K
C636
W839
470
0.01 Y
R647
R615
CF603
EFCT4R5YS5A
R639 100
AT+15V
POWER
TEST POINT
CP601
TKC-M06X-A1
B.OUT
6
INT.MONI
5
IIC_OFF
4
SDA
3
SCL
2
GND
1
OSD_B
2
2
OSD_BLK
OSD_G
VD
OSD_R
I2C_OFF
SDA
SCL
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
A
G-3
B
C
D
E
DEFLECTION SIGNAL
AUDIO SIGNAL
LUMINANCE SIGNAL
TUNER VIDEO SIGNAL
F
R.SIGNAL
G.SIGNAL
B.SIGNAL
PCB010
TMX456
G
1
H
G-4
A
B
C
D
E
F
DEFLECTION/CRT SCHEMATIC DIAGRAM
H
(MAIN PCB)
CD802
2E054401
8
1
+-1%
K001
8115529
C444
2KV 220P BP
-1.9
0
C446
C404
160V 1 MHE
10V 470 YK
500V 22PSL
1.5
2.0
2
4
3
VIDEO
SCREEN
S
B+
ABL
7
330
4.7K
C805
680P W
R811
R815
W838
3
E12
GND
8 NC
E25
E8
5
0.8
C405
FBT+12V
16V470 YK
+B
GND
GND
GND
180V
HEATER
4
GND
3
GND
2
180V
1
CD803
2E044101
CP803A
51052-0400
D404
HEATER
4
99.6
GND
3
GND
2
12
11
NC
F
9
1
8
6
HEATER
5
C435
FROM/TO POWER
101.6
0
W802
100K 1/4W
7
R445_1
100V 22 YK
0
R421_1
100K 1/4W
D422
AU02A-EIC
96.4
6.4
10
D407
AU02A-EIC
100V 0.1 TF
2W
330
1.7
GND
C433
C412
4.7
2
1
CP806
005P-2100
GND 0
11
C448
R443_1
C806
FOCUS
F
AU02A-EIC
P_CON+5V
SOUND+B
4
G
HV
AFC
9
HEA
10 TER
8
B
D408
W824
3.3K 5W
TO SOUND
R
W806
R448_1
0
6.8K 1/2W
C401
6
COL
C802_1
OUT
3
5.0
W823
135.0
R422
10V 470 YK
GND
2
7.8
0
135.0
1.8 2W
AU02A-EIC
W891
3
IN
1
D410
1
C801
C437
R428_1
8.2 2W
1.6KV 0.01 ECWH
C443
0
21
R429_1
FB401
3225010F
130.0
MTZJ6.2B
1
16
130.0
K002
8115529
35V 470 YK
200V 0.018 PP
T401_1
5013001
H.OUTPUT
Q401
2SD2499(LBOEC1)
0
D405
L406 18uH
C416
-0.1
22
5
CP401_1
TS-80P-04-V1
K003
8115529
W897
17
R427
R446
P.CON+5V REG IC
IC402 KIA7805API
4.7K 1/2W
45.7
0
0
100 1/4W
0.3
H_SYNC
P_CON+5V
2
0
5
17.7
4
C440
27.0
ABCL
H_OUT
3
GND
500V 470P B
H.DRIVE
Q402
2SC2621
FROM/TO CHROMA
250V 0.56 ECWF
15
20
MG801
29MMSTAR
330P B
2
1
R804
3
2
TP024
2.7K 1/4W
3
TP023
12K 2W
4
R805
4
C434
100V 22 YK
500V 22P SL
6
DY801
7M062505
TP022
P_CON+5V
C439
R809
CC004
2.7
BLUE OUT
Q802
2SC4075-YAC
4.7K
470 1/2W
100V0.068
TF
R412
R410
470 1/2W
C430
TO DY
D411
6.2K
GREEN OUT
Q803
2SC4075-YAC
CC006
R409
12K +-1%
95.4
CC002
AU02A-EIC
HZ11B1L
3.2
2.7
R806
C427
R
G
B
3.2
98.4
RED OUT
Q801
2SC4075-YAC
5 7 1
50V10 MHE
C422
100V 0.15
TF
9
10
8
6
11
2.7
R807
R406
3.3K
R408
100.6
X-RAY
X-RAY_TEST
7
C804
19
16.1
R424
2
V801
A63AHC26X
X-RAY TEST SW.
Q403
16.0
DTA144ES
18K +-1%
D401
HZ27-1L
D402
1
2
3.2
S803X
100K 1/4W
+-1%
1
D403
1 1/2W
C418
1 1W
R407_2
R416
25V 2200 MHE
R419
6.8K
C417_1
1 TF
R417
11K +-1%
C411
150P SL
1.5K
R420
6
FROM/TO MICON/TUNER
CP801_1
TS-80P-02-V1
4.4
22K +-1%
9.6
R.OUT
CP802B
51048-0510
7
52.0
B.OUT
2.7K 1/4W
VCC
6
5
53.0
11E1-EIC
R401
R.OUT
R813
4
0
R418
R405
18K 1/4W
+-1%
1
L802
HF57T18.5*10*10
CD801_1
8M82025A
18
5
1
2.7K 1/4W
C414
14
R404
2.7K 1/4W
R.OUT
G.OUT
R803
3
27.0
W817
B.OUT
12K 2W
R802
2
25.1
2
PUMP
UP
35V100 MHE
1
4.5
2
CLAMP
12K 2W
THERMAL
PROTECTION
W831
B.OUT
CP802A
51048-0510
AMP+
7
G.OUT
L801
HS401
763WAA0119
CLAMP
3
2KV 0.001 B
V_FEEDBACK
4
3
100uH 0607
V_OUT
4
G.OUT
560P W
V-OUT IC
IC401 LA78041
CLAMP
GND
R814
R.OUT
R.OUT
GND
R816
B.OUT
B.OUT
5
560P W
G.OUT
G.OUT
5
330
CLAMP
CLAMP
8
GND
4.7K
GND
FROM/TO CHROMA
4
G
2
0
J801
CVT3275-5102
180V
1
CP803B
51052-0400
AU02A-EIC
PCB110
TCX315
PCB010
TMX456
R.SIGNAL
G.SIGNAL
B.SIGNAL
DEFLECTION SIGNAL
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
A
G-5
B
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
C
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
D
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
E
F
CAUTION: DIGITAL TRANSISTOR
G
1
H
G-6
A
B
C
D
E
F
G
H
POWER SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
CAUTION:
6.3A 125V
ATTENTION:
7
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE 6.3A 125V (F501)
FUSE.
POUR UNE PROTECTION CONTINUE LES RISQUES
D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 6.3A 125V (F501).
DEGAUSS COIL
L502
8R250009
C647
R655
500V 0.001 B
2.2K 10W
D501
RM11C-EIC
MS501
23MICA
6.9
1
2
H
2
TH501
PTAD14K2-3R0Q141
2
500V 0.001 B
5
4
NC
6.3A 125V
L501
9-000074
6.3A 125V
F501
1
AC120V_60HZ
CD501
0R614909
FH502
EYF-52BC
2
C501
BLACK
WHITE
FH501
EYF-52BC
23706.3
WIDE
BLADE
R177
1.2K 10W
1
D126
EM1C-EIC
C133
3
20W
0
2
180
0
0.7
68K
4.7K
1SS133
1
R504
R505
250V 0.22 ECQUL
D617
C646
C132_1
25V 2200 YK
D608
R643
4
S803Y
RD15FB
S106X
FBT+12V
+B
GND
25V 2200 MHE
33 1/2W
D127
11E1-EIC
W801
R501_1
3W
1M 1/2W
+-10%
1.5
CP501
THL-P03P-B1
11E1-EIC
C506_1
R515
200V 680 MXR
R509
18K +-1%
10K 1/2W
3
P
160V 100 MHE
160V 10 MHE
C519
D503
RM11C-EIC
D125
POWER
Q501
2SC1815Y
R506
R507_1
W818
47 1/4W
5
C507
R503
HS501
763WAA0112
330K 1/4W
R508
TP501
RM11C-EIC
2
0 137.3 179.6 136.6
D504
RY101
ALKS321
5
5
4
6
D502
RM11C-EIC
4
3
1
3
2
1
1
2
CP502
TV-50P-02-A1
C503
2.2K 10W
C504
EM1C-EIC
1.2 7W
500V
500V
0.001 B 0.001 B
POWER REG.IC
IC501
STR30110
6
R640
1
R502
D609
7
4
W815
FROM/TO MICON/TUNER
FROM/TO DEFLECTION/CRT
GND
+B
3
3
POWER
TO CHROMA
P_CON+15V
AT+15V
2
2
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
A
G-7
B
C
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
D
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
E
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
ARE
F
G
1
PCB010
TMX456
H
G-8
A
B
C
D
E
F
G
H
SOUND SCHEMATIC DIAGRAM
8
8
FROM MICON/TUNER
(MAIN PCB)
AUDIO_MUTE
7
FROM CHROMA
7
AUDIO_OUT
GND
6
6
5
5
FROM DEFLECTION/CRT
SPEAKER
P_CON+5V
SP351_2
SA04A05AWA
CP351_1
TID-X02P-B2
SOUND+B
SOUND IC
IC351_1
AN7523
1
1
2
2
SPEAKER
7
1.6
8
0
NC 0
23
2.9
C359_1
5.6K
24
3
50V 2.2 KA
C353_1
W835
S801X
9
W834
S801Y
S809Y
3.9K
R355
6
4.1
C352
C351
5
4.6
R358
4
0
0.0033 M
3
4.6
50V 1 MHE
2
10V 3300 YK
W820
4
SP351_2
SA04A05AWA
GND
VCC
1
5.7
3
+ -
+ +
120K
R356
4
W829
W813
W810
2.9
R354
2
0
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
A
G-9
B
C357_1
W814
50V 10 KA
47K
2
0
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
C
MUTE SW.
Q351
2SC1815Y
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
D
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
E
F
PCB010
TMX456
AUDIO SIGNAL
G
1
H
G-10
WAVEFORMS
MICON/TUNER
1 200mV 5ms/div
6 0.5V 20µs/div
11 1V 20µs/div
2 0.5V 20µs/div
7 200mV 20µs/div
12 1V 20µs/div
3 200mV 20µs/div
8
20V 20µs/div
13 1V 20µs/div
DEFLECTION/CRT
4 200mV 5ms/div
9
200mV 20µs/div
14 0.5V 5ms/div
CHROMA
5 0.5V 2ms/div
10 0.5V 5ms/div
15 20V 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
WAVEFORMS
16 2V 20µs/div
21 50V 20µs/div
17 200V 20µs/div
22 50V 20µs/div
SOUND
18 10V 5ms/div
23 0.5V 1ms/div
19 10V 5ms/div
24 1V 1ms/div
20 50V 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2
MECHANICAL EXPLODED VIEW
111
204
204
204
204
204
113
J801
205
204
119
204
110
116
205
105
119
PCB110
(CRT PCB)
203
L502
205
114
202
205
102 MS501 202
103
115
101
FB401
V801
104
115
ATC001
112
203
TU001
203
SP351
PCB010
(MAIN PCB)
201
201
117
108
201
118
107
120
106
I-1
109
MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
101
102
103
104
105
106
107
108
109
8995034000
------741WUA0021
701APJA036
713WPA0096
7230006856
735WPA0426
CORD CLIP UL CO.
HEAT SINK
HEAT SINK
METAL SPACER
SPRING,EARTH
CABINET,FRONT
GUIDE,REMOCON
SHEET,CAUTION
BUTTON ASS'Y
110
111
112
113
114
115
116
117
118
119
702APA0086
722552A004
723000B179
7232020733
899HV3T001
762WPA0009
8994201000
7220001109
7240001041
---
CABINET,BACK
SHEET,RATING
FILM,DECORATION
SHEET,BRAND
HOLDER,ANODE WIRE
HOLDER,CRT WIRE
HOLDER,CRT WIRE
SHEET,HWC
SHEET,CSA WARNING
COATING CLIP
120
A3I062G720 CABINET,FRONT ASS'Y
201
202
203
204
205
8110630A04
8117D30A04
8109630802
8117540B04
8111J50D04
SCREW,TAP TITE (P)
SCREW,TAPPING (B0)
SCREW,TAP TITE (B)
SCREW,TAPPING (B0)
SCREW,TAPPING (A)
-------------
J3I06201
JB5U0100
792AHA0073
792AHA0074
791AHA0021
793ACDA087
INSTRUCTION BOOK
POLYBAG
PACKAGE,TOP
PACKAGE,BOTTOM
FILM BAG
GIFT BOX
J1-1
BRAZIER
WH8 BRAZIER
BRAZIER
TRUSS
GW22
3x10
3x10
3x8
4x20
5x40
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
DESCRIPTION
RESISTORS
R135
R177
R401
R404
R405
R406
R407
R408
R409
R417
R418
R424
R428
R429
R430
R443
R448
R501
R502
R506
R507
R509
R515
R640
R647
R655
R803
R805
R807
R001T6272J
R5W2CF122J
R4X5T4104F
R002T4272J
R4X5T4183F
R903N8332J
R65581010J
R4X5T6183F
R4X5T6622F
R4X5T6113F
R4X5T6223F
R4X5T6123F
R3X28A8R2J
R6558A1R8J
R00106104J
R6558A4R7J
R5X2CD332J
R21202105K
R5X2CE1R2J
R5W2CH181J
R655U4470J
R4X5T6183F
R3X28B1R5J
R5X2CF222J
R00106182J
R5X2CF222J
R3X18A123J
R3X18A123J
R3X18A123J
RC
R, CEMENT
R, METAL
RC
R, METAL
RC
R, FUSE
R, METAL
R, METAL
R, METAL
R, METAL
R, METAL
R, METAL
R, FUSE
RC
R, FUSE
R, CEMENT
R, SOLID
R, CEMENT
R, CEMENT
R, FUSE
R, METAL
R, METAL
R, CEMENT
RC
R, CEMENT
R, METAL OXIDE
R, METAL OXIDE
R, METAL OXIDE
C132
C351
C404
C405
C412
C414
C416
C418
C433
C434
C437
C443
C444
C446
C448
C501
C506
C507
C519
C624
C646
C699
E5EZF3222M
E02LF1332M
E02LT1471M
E02LT2471M
E02LT1471M
E5EZT4101M
P3N1F2183J
E5EZF3222M
E02LT4471M
E02LT8220M
P411F3564J
P414F9103H
C01BBP7H2K
E5EZTB010M
E02LT8220M
P2122B224M
E52SFC681M
E5EZFB101M
E5EZTB100M
E02L01222M
E02LF3222M
CHGTY0214M
CE
CE
CE
CE
CE
CE
CPP
CE
CE
CE
CMPP
CMPP
CC
CE
CE
CMP
CE
CE
CE
CE
CE
CC
D001
D101
D103
D104
D125
D126
D127
D401
D402
D403
D404
D405
D407
D408
D410
D411
D422
D501
D502
D503
D504
D601
D602
D603
D94TA30013 DIODE, ZENER
D97U06R81B DIODE, ZENER
D97U06R81B DIODE, ZENER
D97U06R81B DIODE, ZENER
D1VT001330 DIODE, SILICON
D2WT0EM1C0 DIODE, SILICON
D2WT011E10 DIODE, SILICON
D94TA27011 DIODE, ZENER
D94TA11B11 DIODE, ZENER
D2WT011E10 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D97U06R21B DIODE, ZENER
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTRM11C0 DOIDE, SILICON
D2WTRM11C0 DOIDE, SILICON
D2WTRM11C0 DOIDE, SILICON
D2WTRM11C0 DOIDE, SILICON
D1VT001330 DIODE, SILICON
D97U08R21B DIODE, ZENER
D1VT001330 DIODE, SILICON
REF. NO. PART NO.
2.7K OHM 1/6W
1.2K OHM 10W
100K OHM 1/4W
2.7K OHM 1/4W
18K OHM 1/4W
3.3K OHM 1/8W
1 OHM 1W
18K OHM 1/6W
6.2K OHM 1/6W
11K OHM 1/6W
22K OHM 1/6W
12K OHM 1/6W
8.2 OHM 2W
1.8 OHM 2W
100K OHM 1/6W
4.7 OHM 2W
3.3K OHM 5W
1M OHM 1/2W
1.2 OHM 7W
180 OHM 20W
47 OHM 1/4W
18K OHM 1/6W
1.5 OHM 3W
2.2K OHM 10W
1.8K OHM 1/6W
2.2K OHM 10W
12K OHM 2W
12K OHM 2W
12K OHM 2W
D604
D605
D607
D608
D609
D610
D611
D612
D614
D615
D616
D617
D1VT001330
D2WT011E10
D1VT001330
D9201150B1
D2WT0EM1C0
D97U01201B
D97U01201B
D97U01201B
D97U06R21B
D97U06R21B
D97U06R21B
D2WT011E10
IC101
IC199
IC351
IC401
IC402
IC501
IC601
I56F07044A
A3I051G015
I0FSP75230
I03TD80410
I1KA97805A
I2B4901100
I06FC12030
IC
IC
IC
IC
IC
IC
IC
!
!
!
!
!
!
!
!
!
!
!
Q101
Q351
Q401
Q402
Q403
Q501
Q603
Q606
Q608
Q801
Q802
Q803
TNYTJ03001
TC5T018154
TDUU024990
TC3Q026210
TPYTD03001
TC5T018154
TD3T007340
TD3T007340
TA5T010154
TC3Q040750
TC3Q040750
TC3Q040750
COMPOUND TRANSISTOR
TRANSISTOR, SILICON
TRANSISTOR, SILICON
TRANSISTOR, SILICON
COMPOUND TRANSISTOR
TRANSISTOR, SILICON
TRANSISTOR, SILICON
TRANSISTOR, SILICON
TRANSISTOR, SILICON
TRANSISTOR, SILICON
TRANSISTOR, SILICON
TRANSISTOR, SILICON
L101
L406
! L501
! L502
L601
L603
L605
L607
L801
L802
T401
021LA63R3K
021U6D180K
029K000074
028R250009
0216731R2K
021673100K
0216731R0J
021LA6150K
02167D101K
02A6A8A0A1
045013001J
COIL
COIL
COIL, LINE FILTER
COIL, DEGAUSS
COIL
COIL
COIL
COIL
COIL
CORE, FERRITE
TRANS, HORIZONTAL DRIVE
! J801
066C130015
SOCKET, CRT
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
OEC7044A
S-24C02BDP-1A
AN7523
LA78041
KIA7805API
STR30110
M61203BFP
DTC114TSTP
2SC1815Y(TPE2)
2SD2499(LBOEC1)
2SC2621(D,E)-RAC
DTA144ESTP
2SC1815Y(TPE2)
2SD734(E,F)-AA
2SD734(E,F)-AA
2SA1015Y(TPE2)
2SC4075-YAC
2SC4075-YAC
2SC4075-YAC
COILS &TRANSFORMERS
3.3 UH
18 UH
9-000074
8R250009
1.2 UH
10 UH
1 UH
15 UH
100 UH
HF57T18.5*10*10
5013001
JACK
CVT3275-5102
SWITCHES
SW101
SW102
DIODES
!
1SS133T-77
11E1-EIC
1SS133T-77
RD15FB
EM1C-EIC
MTZJ12B T-77
MTZJ12B T-77
MTZJ12B T-77
MTZJ6.2B T-77
MTZJ6.2B T-77
MTZJ6.2B T-77
11E1-EIC
TRANSISTORS
2200 UF 25V
3300 UF 10V
470 UF 10V
470 UF 16V
470 UF 10V
100 UF 35V
0.018 UF 200V
2200 UF 25V
470 UF 35V
22 UF 100V
0.56 UF 250V ECWF
0.01 UF 1.6KV ECWH
220 PF 2KV BP
1UF 160V
22 UF 100V
0.22 UF 250V ECQUL
680 UF 200V
100 UF 160V
10UF 160V
2200 UF 10V
2200 UF 25V
0.01 UF 16V Y
SW103
HZ30-3L TD
MTZJ6.8B T-77
MTZJ6.8B T-77
MTZJ6.8B T-77
1SS133T-77
EM1C-EIC
11E1-EIC
HZ27-1L TD
HZ11B1L TD
11E1-EIC
AU02A-EIC
MTZJ6.2B T-77
AU02A-EIC
AU02A-EIC
AU02A-EIC
AU02A-EIC
AU02A-EIC
RM11C-EIC
RM11C-EIC
RM11C-EIC
RM11C-EIC
1SS133T-77
MTZJ8.2B T-77
1SS133T-77
DIODE, SILICON
DIODE, SILICON
DIODE, SILICON
DIODE, ZENER
DIODE, SILICON
DIODE, ZENER
DIODE, ZENER
DIODE, ZENER
DIODE, ZENER
DIODE, ZENER
DIODE, ZENER
DIODE, SILICON
ICS
CAPACITORS
!
!
!
!
DESCRIPTION
DIODES
SW104
SW105
0504201T31
0504101T34
0504201T31
0504101T34
0504201T31
0504101T34
0504201T31
0504101T34
0504201T31
0504101T34
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SWITCH, TACT
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
or
or
or
or
or
P.C.BOARD ASSEMBLIES
PCB010
PCB110
A3I058G01A
A3I057G11A
! ATC001
! CD501
0632400008
120R614909
1207614909
068M82025A
122E054401
122E044101
1022T45R72
1011T4R504
1011T4R517
069W120019
069W340018
0697320039
069W420029
0697260650
069W320018
PCB ASS'Y
PCB ASS'Y
TMX456A
TCX315A
MISCELLANEOUS
CD801
CD802
CD803
CF601
CF603
CF604
CP351
! CP401
! CP501
! CP502
CP601
CP801
J2-1
ANT, UNIT
CORD, AC
CORD, AC
CORD, CONNECTOR
CORD, JUMPER
CORD, JUMPER
FILTER, SAW
FILTER, CERAMIC
FILTER, CERAMIC
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CORD, UX CONNECTOR
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
NXC0032-010010
0R614909
or
7614909
8M82025A
122E054401
122E044101
SAF45MFY220ZR
EFCT4R5YS5A
EFCT4R5MW5
TID-X02P-B2
TS-80P-04-V1
THL-P03P-B1
TV-50P-02-A1
TKC-M06X-A1
TS-80P-02-V1
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
!
!
!
!
!
!
!
!
!
!
!
CP806
CP802A
CP802B
CP803A
CP803B
DY801
F501
FB401
FH501
FH502
K001
K002
K003
MG801
MS501
OS101
RY101
SP351
TH501
TM101
TU001
V801
X101
X602
069W010010
067R005019
067R005019
067R104019
067R104019
027M062505
081PA6R302
043225010F
06710T0006
06710T0006
129A000010
129A000010
129A000010
026A062704
128B000018
077Q014003
0560V20115
070C533016
DF40A3R0Q0
076R074180
0145W00049
0984250502
1002T00801
100CT3R505
DESCRIPTION
MISCELLANEOUS
CONNECTOR PCB SIDE
WIRE HOLDER
WIRE HOLDER
WIRE HOLDER
WIRE HOLDER
DY
FUSE
TRANSFORMER, FLYBACK
HOLDER, FUSE
HOLDER, FUSE
WEDGE
WEDGE
WEDGE
MAGNET, CONVERGENCE
SHEET
REMOTE RECEIVER
RELAY
SPEAKER
DEGAUSS, ELEMENT
TRANSMITTER
TUNER, VHF-UHF
COLOR, PICTURE TUBE
CERAMIC OSILLATOR
CRYSTAL HC-49/C
005P-2100
51048-0510
51048-0510
51052-0400
51052-0400
7M062505
23706.3
3225010F
EYF-52BC
EYF-52BC
8115529
8115529
8115529
29MMSTAR
23MICA
PIC-28143SY-2
ALKS321
SA04A05AWA
PTAD14K2-3R0Q141
R25-1127
NJH3021U268
A63AHC26X
8MHz
3.579545MHz
RESISTOR
RC................... CARBON RESISTOR
CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................. METAL POLYESTER CAPACITOR
CMPL............... METAL PLASTIC CAPACITOR
CMPP.............. METAL POLYPROPYLENE CAPACITOR
J2-2
SPEC.NO.
M3I0-62G
O/R NO.
A063519