Download Datalogic Scanning TC1100-1100 User's Manual

CODE SELECTION
EAN/UPC disable
EAN 8/EAN 13/UPC A/UPC E enable
EAN 8/EAN 13 enable
UPC A/UPC E enable
EAN 8 enable
EAN 13 enable
UPC A enable
UPC E enable
Code 39 disable
Code 39 Standard enable
Code 39Full ASCII enable
Code 2/5 family disable
Interleaved 2/5 enable
Normal 2/5 5 bars enable
Industrial 2/5 (IATA) enable
Matrix 2/5 3 bars enable
Codabar family disable
Codabar standard enable
Code 128 family disable
Code 128 enable
EAN 128 enable
Code Length
Code 93 family disable
Code 93 enable
PDF417 disable
PDF417 enable
Pharmacode disable
Pharmacode enable
Overflow ratio
xxyy = ASCII numbers that define:
xx = min. acceptable code length
AA0
AA1
AA5
AA8
AA3
AAK
AAL
AA6
AA4
AAM
AAN
AA7
AAG0
AAG1
AAH0
AAH1
AAI0
AAI1
AAJ0
AAJ1
AB0
AB11xxyy
AB12xxyy
AB13xxyy
AB21xxyy
AB22xxyy
AC0
AC11xxyy
AC12xxyy
AC13xxyy
AC21xxyy
AC22xxyy
AC23xxyy
AC31xxyy
AC32xxyy
AC33xxyy
AC41xxyy
AC42xxyy
AC43xxyy
AD0
AD111xxyy
AD112xxyy
AD121xxyy
AD122xxyy
AD212xxyy
AI0
AI11 xxyy
AI21 xxyy
AILxxyy
AK0
AK1 xxyy
AR0
AR1
AQ0
AQ1xxyy
AQ2xxyy
AQAzz
without ADD ON
with ADD ON
with and without ADD ON
without ADD ON
with ADD ON 2 ONLY
with ADD ON 5 ONLY
with ADD ON 2 AND 5
without ADD ON
with ADD ON 2 ONLY
with ADD ON 5 ONLY
with ADD ON 2 AND 5
check digit transmission disable
check digit transmission enable
check digit transmission disable
check digit transmission enable
check digit transmission disable
check digit transmission enable
check digit transmission disable
check digit transmission enable
TC1100
CCD Scanner
Quick Reference Guide
The TC1100 is a linear CCD Scanner for OEM applications. It is available in two different versions:
Model
TC1100-1100
TC1100-1200
Description
CCD scanner for linear codes
CCD scanner for linear and PDF417
Technical Specifications
no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission
Power supply
5 Vdc ± 5%
Consumption
1.5 W
Interfaces
RS232, WEDGE, PEN Emulation
Max Scans/sec
270
Max resolution
0,076mm (3mils)
EAN/UPC, Code 39, 2/5 family, Codabar, Code 128, EAN 128, ISBT 128, Code 93,
pharmaceutical codes, Delta IBM, Code 16K, Code 49, (Telepen, MSI/Plessey, Pharmacode
only TC1100-1100), (Codablock-A, Codablock-F Std, Codablock-F EAN, PDF417 only
TC1100-1200)
Readable codes:
no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission
check digit control without transmission
Default Configuration
Power Save
Reading Parameters
Code Selection
Enabled codes
no start/stop character equality control - nor transmission
no start/stop character equality control but transmission
start/stop character equality control but no transmission
start/stop character equality control and transmission
ABC Codabar no start/stop character equality control but transmission
control without transmission of check digit
control without transmission of check digit
(Only TC1100-1200)
Data Format
Decoding Parameters
Enabled interface
270 scans/sec, sleep disabled, standby disabled
On-Line
• Interleaved 2 of 5: Check Digit transmitted, length: min 4, max 99
• Code EAN8, EAN13, UPCA, UPCB: without ADD ON, Check Digit transmitted, no conversions
• Code 39: length: min 1, max 99
• Code 128: Check Digit not transmitted, length: min 1, max 99
• PDF417
Code ID disabled, Header = <STX>, Terminator = <CR> <LF>, no Field Adjustment, Code
length TX disabled, character replacement disabled, No Read Character = <CAN>
Ink spread enabled, overflow control enabled, interdigit control enabled, Puzzle Solver™
disabled, decoding safety = 1 read
RS232, 9600, N, 8, 1, no handshaking, ACK/NAK disabled, RX timeout 100 ms, FIFO
enabled, inter-character delay disabled
Reading Diagrams
mm
160
control without transmission of check digit
0
20
40
60
80
100 120
140
160
180
200 220
240 260
280 300
forward code tx direction
reverse code tx direction
20
30
40
50
60
70
80
90
100 110 120 130 140 150 160 170 180
40
0.17 mm
30
(6.6 mils)
20
20
For more detailed information on the TC1100 programmability and complete parameter list, please refer to the
TC1100 Reference Manual.
10
50
40
The minimum code length must always be less than or equal to the maximum.
0
90
60
0.20 mm
60
zz = overflow ratio value
mm
70
100
80
320
80
140
120
yy = max. acceptable code length
Order Number
939501020
939501030
10
0
0
-20
-10
-40
-20
0.25 mm
-30
(10 mils)
-60
-40
-80
-50
-100
-60
-120
-140
-160
0.13 mm
0.20 mm
0.30 mm
0.50 mm
-70
0.38 mm
(5 mils)
(8 mils)
(12 mils)
(20 mils)
-80
(15 mils)
-90
N2468
821000676 (Rev. H)
Reading Diagram TC1100-1100 (code 39)
Reading Diagram TC1100-1200 (PDF417)
Electrical Connections
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
25-pin connector
Shield
earth ground
TX
transmit data
RX
receive data
RTS
request to send
CTS
clear to send
nc
not connected
SGND
signal ground
EXT BEEPER
external beeper connection
VCC+
+5Vdc
nc
not connected
OUT+
See Figure 1
OUTVCC+
+5Vdc
nc
not connected
nc
not connected
nc
not connected
nc
not connected
EXT TRIG+
See Figure 2
EXT TRIGDATAIN_WAND
DATAOUT
OUTCLKIN
CLKOUT
GND
power ground
11
12
Vext 40 Vdc max
ON = Good Read
18
19
Vext 30 Vdc max.
TC1100
Vext 30 Vdc max. EXTERNAL TRIGGER
+ 5V
V
EXT TRIG+
+ 5V
V
Signal
18 EXT TRIG+
EXT TRIG19
Signal
OUT -
Input NPN command using external power
TC1100
EXT TRIG-
Ground
Input PNP command using external power
+ 5V
Return to RS232 Interface
EXTERNAL TRIGGER
13 Vcc 5Vdc
V
+ 5V
18 EXT TRIG+
18 EXT TRIG+
19 EXT TRIG-
19
EXT TRIG-
25
GND
25 GND
Ì$+CP0$-$Î
TC1100
EXTERNAL TRIGGER
13 Vcc 5Vdc
Ground
Signal
Input NPN command using TC1100 power
V
Signal
Ground
Input PNP command using TC1100 power
Figure 2 - Trigger Connections
For WEDGE Users
Basic Commands for TC1100
The TC1100 default configuration can be changed by receiving commands through the RS232
Interface. The command syntax is given below with an example.
70.7 mm
68.6 mm
30.5 mm
2.78 inches
2.70 inches
1.20 inches
GOOD READ (the LED will remain ON until status changes)
OFF = No Read
Command syntax
$+ Command(s) $- <CR> the new setting will be definitive (stored in FLASH EPROM)
Example:
Multiple command programming sequence:
$+
BK0 CD7
AC410132
$-
CR
Enter configuration environment
Carriage return character (0D Hex.)
Exit and save new configuration
30.5
[1.20]
Serial On-Line Operating Mode
Baud Rate = 19200
Matrix 2/5 3 bars: no check digit,
variable length code from 1 to 32 characters
Commands:
24
[0.94]
68.6
[2.70]
10.4
[0.41]
9.5
[0.37]
7.6
[0.30]
54
[2.13]
OPERATING MODES
70.7
[2.78]
EXTERNAL TRIGGER
Figure 1 - Output Connection (Good Read). Example NPN
Width
Length
Height
ON = Power ON
OFF = Power OFF
TC1100
OUT +
Physical Dimensions
Led Status
POWER ON
USER INTERFACE
TC1100
On-line
Serial On-line
Automatic
Automatic / Lighting System Standby
To enter in Test mode
To exit Test mode
BK1
BK0
BK3
BK2
#+DStat1<CR> (does not require $+ or $-)
#+DStat0<CR> (does not require $+ or $-)
RS232 interface selection
RS232 Baud Rate
WEDGE AT
WEDGE Notebook
Keyboard Nationality
CP0
CD0
for 150 Baud up to CD8 for 38400 Baud
CP500
CP505
FJ7
Belgian
FJ1
FJ4
English
FJ6
FJ2
French
FJ5
FJ3
German
FJ0
BT0
67 scans/sec
BT1
135 scans/sec
BT2
270 scans/sec
AU1
enable
AU0
AX1
enable
AX0
ED0
1 read
ED2
ED1
2 reads
ED3
$+$*<CR> (does not require $-)
$+$&<CR> (does not require $-)
GENERAL FEATURES
31.6
[1.25]
mm
[in.]
CCD Scan Rate
17.7
[0.70]
Optical Axis
Puzzle Solver
Ink Spread
Decoding safety
To restore the default configuration
To get configuration from the scanner
Italian
Spanish
Swedish
USA
disable
disable
3 reads
4 reads