Transcript
YORKVILLE™ 16-1/8" ELONGATED PRESSURE-ASSISTED TOILET VITREOUS CHINA BARRIER FREE YORKVILLE™ 16-1/8" ELONGATED PRESSURE-ASSISTED TOILET ❏ 2325.101 • Vitreous china • Low-consumption (6.0 Lpf/1.6 gpf) • Floor-mounted, back-outlet toilet • Elongated 16-1/8" high bowl • Pressure-assisted siphon jet flush action • Side-mounted chrome trip lever • Close-coupled flushometer tank* • Speed Connect ® tank/bowl coupling system • 4 bolt caps • Fully glazed 2" ballpass trapway • 10" x 12" water surface area • 100% factory flush tested ❏ 3125.016 Elongated 16-1/8" high bowl with four bolt caps and two floor screws ❏ 4099.100 Flushometer tank complete with coupling components Component parts: ❏ 735084-400 Tank cover (specify color) Replaces 2325.100 Nominal Dimensions: 819 x 495 x 803mm (32-1/4" x 19-1/2" x 31-5/8") FINISHED WALL Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112.19.2 for Vitreous China Fixtures To Be Specified: ❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver ❏ Fawn Beige ❏ Black ❏ Seat: American Standard #5324.019 Elongated “Rise and Shine” (with easy to clean lift-off hinge system) solid plastic closed front seat with cover. ❏ Seat: American Standard #5325.024 Elongated “Rise and Shine” (with easy to clean lift-off hinge system) solid plastic open front seat with cover. ❏ Alternate Seat: ❏ Supply with Stop: * Flushmate III tank system by Flushmate ® Div. of Sloan Valve Co © 2008 AS America Inc. 470mm (18-1/2) C/L C/L OF SEAT POST HOLES 140 mm (5-1/2) CENTER 64mm (2-1/2) Recommended working pressure range 20 psi - 80ps 495mm (19-1/2) 279mm (11) Alternate Configurations: ❏ 4099.700 Tank and tank cover only with tank cover locking device ❏ 4099.800 Tank and tank cover only with right hand trip lever Fixture only, seat and supply by others 819mm (32-1/4) 19mm ± 6mm (3/4 ± 1/4) 381mm (15) FLEX SUPPLY AS REQ. 410mm (16-1/8) * 222mm 102 mm (4) (8-3/4) 13 x 19mm (1/2 x 3/4) SLOTS 76mm (3) 152 mm (6) 76mm (3) C/L OF WASTE OUTLET 324mm (12-3/4) C/L OF 1/2" DIA HOLES 152mm (6) CENTERS 803mm (31-5/8) 235mm (9-1/4) FINISHED FLOOR 648mm (25-1/2) NOTES: WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITEFELT (WAX RING NOT RECOMMENDED). SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. *FOR ADDITIONAL INFORMATION REFER TO INSTALLATION INSTRUCTIONS SUPPLIED. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES-CHECK LOCAL CODES. M42 Revised 2/08