Download American Standard Cadet 3 Round Front Rough-In Toilet 2384.012 User's Manual
Transcript
CADET® 3 ROUND FRONT ROUGH-IN TOILET VITREOUS CHINA CADET® 3 ROUND FRONT TOILET ❑ 2384.012 •Vitreous china •Low-consumption (6.0 Lpf/1.6 gpf) • EverClean® surface inhibits the growth of stain- and odor-causing bacteria, mold, and mildew on the surface •Features the Cadet ® 3 Flushing System •Space saving round front siphon action jetted bowl •Fully-glazed 2-1/8" trapway with 2" ball pass •Generous 9" x 8" water surface area •Close-coupled tank with flat tank cover for superior storage •Oversized 3" flush valve with chemical resistant flapper •Chrome trip lever •Speed Connect ® tank-to-bowl coupling system •Sanitary dam on bowl with four point tank stabilization •2 color-matched bolt caps •100% factory flush tested • 5 year warranty ❑ 3011.016 Round Front Bowl ❑ 4021.016 Tank Nominal Dimensions: 718 x 438 x 733mm (28-1/4" x 17-1/4" x 28-7/8") Fixture only, seat and supply by others SEE REVERSE FOR ADDITIONAL ROUGHING-IN DIMENSIONS To Be Specified: ❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen ❏ Black Alternative Tank Configurations Available: ❏ Seat: #5330.010 Round front Champion ® Slow Close ❑ 4021.500 Tank complete with Aquaguard Liner solid plastic seat and cover with easy lift off feature ❑ 4021.600 Tank complete with tank cover ❏ Seat: #5282.011 Round Front EverClean ® solid locking device plastic seat and cover ❑ 4021.700 Tank complete with Aquaguard Liner ❏ Seat: #5320.110 EverClean ® Round Front Seat with and tank cover locking device Slow Close Snap-Off Hinges ❑ 4021.800 Tank complete with trip lever located ❏ Supply with stop: on right side ❑ 4021.900 Tank complete with tank cover locking device and trip lever located on right side ❑ 4021.950 Tank complete with Aquaguard liner, tank cover locking devise, and trip lever on right side Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112.19.2M for Vitreous China Fixtures includes Flush Performance, Ball Pass Diameter, NOTES: Trap Seal Depth and all Dimensions THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. • Los Angeles Department of Water and Power SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED Supplementary Purchase Specification for SEPARATELY. Non-Adjustability * DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. © 2008 AS America Inc. K67 Revised 2/08 CADET® 3 ROUND FRONT ROUGH-IN TOILET VITREOUS CHINA FINISHED WALL 718mm (28-1/4) 25mm ± 6mm (1 ± 1/4) 438mm (17-1/4) 216mm (8-1/2) 416mm (16-3/8) C/L OF SEAT POST HOLES 140mm (5-1/2 CENTERS) 733mm (28-7/8) 102mm (4) SUPPLY AS REQ'D. *381mm (15) *203mm (8) 216mm (8-1/2) 305mm (12) 333mm (13-1/8) FINISHED FLOOR C/L OF OUTLET 352mm (13-7/8) 235mm (9-1/4) *152mm (6) NOTES: THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. * DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. © 2008 AS America Inc. K68 Revised 2/08