Download American Standard Cadet 3 Elongated Toilet 2383.012 User's Manual
Transcript
CADET® 3 ELONGATED TOILET VITREOUS CHINA CADET® 3 ELONGATED TOILET ❑ 2383.012 •Vitreous china •Low-consumption (6.0 Lpf/1.6 gpf) • EverClean® surface inhibits the growth of stain- and odor-causing bacteria, mold, and mildew on the surface •Features the Cadet ® 3 Flushing System •Elongated siphon action jetted bowl •Fully-glazed 2-1/8" trapway with 2" ball pass •Generous 9" x 8" water surface area •Close-coupled tank with flat tank cover for superior storage •Oversized 3" flush valve with chemical resistant flapper •Chrome trip lever •Speed Connect ® tank-to-bowl coupling system •Sanitary dam on bowl with four point tank stabilization •2 color-matched bolt caps •100% factory flush tested • 5 year warranty ❑ 3014.016 Elongated Bowl ❑ 4021.016 Tank Nominal Dimensions: 768 x 438 x 733mm (30-1/4" x 17-1/4" x 28-7/8") Fixture only, seat and supply by others SEE REVERSE FOR ADDITIONAL ROUGHING-IN DIMENSIONS To Be Specified: Alternative Tank Configurations Available: ❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen ❏ Black ❑ 4021.500 Tank complete with Aquaguard Liner ❏ Seat: #5325.010 Elongated Champion ® Slow Close ❑ 4021.600 Tank complete with tank cover solid plastic seat and cover with easy lift off feature locking device ❏ Seat: #5284.016 Elongated EverClean® solid plastic ❑ 4021.700 Tank complete with Aquaguard Liner seat and cover ❏ Seat: #5321.110 EverClean ® Elongated Seat with and tank cover locking device Slow Close Snap-Off Hinges ❑ 4021.800 Tank complete with trip lever located ❏ Supply with stop: on right side ❑ 4021.900 Tank complete with tank cover locking device and trip lever located on right side ❑ 4021.950 Tank complete with Aquaguard liner, tank cover locking devise, and trip lever on right side Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112.19.2M for Vitreous China Fixtures NOTES: includes Flush Performance, Ball Pass Diameter, THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF Trap Seal Depth and all Dimensions 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED • Los Angeles Department of Water and Power SEPARATELY. Supplementary Purchase Specification for * DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. Non-Adjustability IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. © 2008 AS America Inc. K61 Revised 2/08 CADET® 3 ELONGATED TOILET VITREOUS CHINA FINISHED WALL 768mm (30-1/4) 25mm ± 6mm (1 ± 1/4) 438mm (17-1/4) 216mm (8-1/2) 470mm (18-1/2) C/L OF SEAT POST HOLES 140mm (5-1/2 CENTERS) 733mm (28-7/8) 102mm (4) SUPPLY AS REQ'D. 381mm (15) *203mm (8) 216mm (8-1/2) 305mm (12) 348mm (13-11/16) FINISHED FLOOR C/L OF OUTLET 352mm (13-7/8) 237mm (9-5/16) *152mm (6) NOTES: THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. * DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. © 2008 AS America Inc. K62 Revised 2/08