Download American Standard 1340M Series User's Manual
Transcript
Installation Instructions 1340 SERIES 1340M SERIES SINGLE TAP PUSH BUTTON FAUCET METERING FAUCET 1340 SERIES FOR COLD AND TEMPERED SUPPLIES 1340M SERIES INCLUDES BELOW DECK MIXING VALVE WITH STRAINER PUSH Certified to comply with ANSI A112.18.1M U.S. PATENT NOS. Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. WARNING: SUPPLY INLET MUST BE FILTERED WITH A 60 MESH SCREEN. USE AMERICAN STANDARD MIXING VALVE WITH STRAINER OR COMMERCIAL 60 MESH STRAINER. SET SCREWS BODY AERATOR 2 HANDLE ASSEMBLING MOUNTING KIT LOCK RING Thread (3) SCREWS into LOCK RING. KEY SCREWS should extend half-way thru RING. SPRING GASKET RETAINING RING LEVER ESCUTCHEON KIT (OPTIONAL) VALVE CARTRIDGE DECK HANDLE RETAINER WASHER, BRASS RISER TUBE (NOT INCLUDED) 1340 SERIES 1 1340M SERIES ASSEMBLING ESCUTCHEON KIT (OPTIONAL) CAUTION Turn off hot and cold water supplies before beginning. Peel off paper backing from PADS and stick both PADS to underside of ESCUTCHEON about 1/4" from ends. Peel off paper backing from WASHER and stick WASHER into circular groove of SUPPORT PLATE. Apply a bead of PUTTY around the inside of ESCUTCHEON edge. PAD Turn ESCUTCHEON over and center it with SUPPORT PLATE over center hole PUTTY of sink deck. Install faucet through the ESCUTCHEON being sure the rubber GASKET is between the FAUCET and the ESCUTCHEON. Install brass WASHER and turn LOCK-RING onto SHANK. Tighten (3) SCREWS in the LOCK-RING to secure fitting. STRAINER FOR 1340M SERIES Connect FLEXIBLE FAUCET SUPPLIES (1/2" faucet cone on one end, 3/8" compression on the other) to the MIXING MIXING VALVE INLETS and the VALVE hot/cold wall stops. ADJUSTMENT The FLEXIBLE FAUCET FLEXIBLE SUPPLIES are NOT FAUCET included. Turn on WALL SUPPLIES STOPS and check WALL for leaks. HOT STOPS FILTER SCREEN Place SUPPORT PLATE in center of ESCUTCHEON with WASHER visible. MOUNTING FITTING Connect RISER TUBE to COLD or TEMPERED water supply. SUPPLY NUT DUCK BILL CHECKS 3 SCREWS FOR 1340 SERIES ONLY Warning; 60 MESH STRAINER required for supply water. Install RISER TUBE (not included) and tighten SUPPLY NUT. LOCK-RING AND SCREWS MIXING STRAINER VALVE ASSEMBLY 012692D WASHER With WALL STOPS open and water flowing, adjust MIXING VALVE to temper water. MIXING VALVE PAD SUPPORT PLATE ESCUTCHEON MIXING VALVE HOTTER COLDER MIXING VALVE INLETS COLD 4 7 sec. TO OPERATE PUSH Start + 40 sec. Lever Stop Automatic Retaining Ring 10 sec. minimum Lift off retaining ring then slide out lever horizontally. Press down to start. 5 Cycle time is factory set but can be changed as shown. TO SERVICE TIGHTEN SET SCREWS TO remove HANDLE use a 3/32" ALLEN WRENCH to loosen three set screws in the HANDLE as shown in Figure A. Remove VALVE CARTRIDGE for cleaning or replacement, see in Figure B. VALVE CARTRIDGE Reassemble in reverse order, Figures C & D. TIGHTEN VALVE CARTRIDGE HANDLE REMOVE REPLACE Figure D 3/32" ALLEN WRENCH Figure A 6 Figure B SPRAY INSTALLATION/REMOVAL 7 Figure C ROUGHING-IN DIMENSIONS 48mm (1-55/64) 111mm (4-3/8) 45mm (1-3/4DIA.) 53mm (2) 30° Use included key to install SPRAY into spout end. HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Product names listed herein are trademarks of American Standard Inc. C American Standard Inc. 1996 25mm (1" MAX) 21mm (53/64 DIA.) 1/2"-14 NPSM THREAD 90mm (3-9/16) All dimensions are approximate and for reference only. 012692D