Transcript
S P E F C I L E ET-PKD110H Ceiling mount bracket for high ceilings D escription This ceiling mount bracket is used when mounting a PT-DZ570 series DLP ™ projector to high ceilings. Specifications Vertical correction angle: Horizontal slant correction angle: Horizontal turn correction angle: Dimensions (W × H × D): +5°, -17° ±2.5° ±1.2° 344 × 340 – 420 × 300 mm (13-17/32˝ × 13-3/8˝–16-17/32˝ × 11-13/16˝) Approx. 9.2 kg* (20.3 lbs*) Weight: * Average value. May differ depending on models. Parts Attachment plate . . . . . Projector mount bracket Adjuster pole A . . . . . . . Adjuster pole B . . . . . . . Angle adjuster . . . . . . . . Pole support bracket 1 . Pole support bracket 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1 1 1 1 1 Pole fixing bracket . . . . . . . . . Washer-fitted bolts (M6 × 80) . Washers (M6) . . . . . . . . . . . . . Hexagonal nuts (M6) . . . . . . . . Washer-fitted screws (M4 × 12) Washer-fitted screws (M6 × 12) Seal packing . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 2 . 2 . 2 . 4 30 . 1 Caution: • Mounting should be done by a qualified technician. • Make sure that the mounting (ceiling) area has sufficient strength. • Read the enclosed mounting instructions thoroughly before starting. • Do not use an electric screwdriver or impact driver to tighten screws. Use a torque driver or hexagon torque wrench and tighten screws to the torque specified in the instructions. • When the product is no longer going to be used, have it disposed of quickly by a professional disposal service. Dimensions Illustration shows the bracket attached to a projector. Attachment plate 344 (13-17/32) 200 (7-7/8 ) 431–511* (16-31/32– 20-1/8 ) ∅ 60.5 (∅ 2-3/8 ) 340 – 420 * (13-3/8 –16-17/32) 12 (∅ 15/32) Attachment plate 2-3-R6 (2-3-R1/4) * Adjustable in 40 mm (1-9/16˝) steps 253.5 ( 9-31/32) 231 ( 9-3/32) 200 (7-7/8 ) Projector 100 ( 3-15/16 ) 100 ( 3-15/16 ) 300 (11-13/16 ) unit : mm (inch) NOTE: This illustration is not drawn to scale. 100 ( 3-15/16 ) 100 ( 3-15/16 ) Attachment plate DLP and the DLP logo are trademarks of Texas Instruments. Weights and dimensions shown are approximate. Specifications subject to change without notice. As of October 2010 SFD10A015 1/1