Download Chief KRA212B mounting kit
Transcript
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation K2C Single to Dual Arm Conversion Accessory Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description KRA212 Installation Instructions KRA212 DISCLAIMER WARNING: Failure to provide adequate structural strength Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the converted K2C mount up to (and including) the display does not exceed 25 lbs (11.34 kg) per arm. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury. Chief® is a registered trademark of Milestone AV Technologies. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS! WARNING: Use this mounting system only for its intended WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. use as described in these instructions. Do not use attachments not recommended by the manufacturer. CAUTION: A CAUTION alerts you to the possibility of WARNING: Never operate this mounting system if it is damage or destruction of equipment if you do not follow the corresponding instructions. damaged. Return the mounting system to a service center for examination and repair. WARNING: Failure to read, thoroughly understand, and WARNING: Do not use this product outdoors. follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. --SAVE THESE INSTRUCTIONS!-- DIMENSIONS (AFTER CONVERSION) MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 28.8" [731.5] EXTENSION MIN 2.98 [75.7] MAX 17.4 [450.7] 100 3.94 90 INTERFACE ROTATION 75 2.95 PITCH RANGE 15 PITCH TENSION KNOB MANUAL HEIGHT ADJUSTMENT RANGE 242.9 9.56 CABLE MANAGEMENT HEIGHT ADJUSTMENT KNOB DESKTOP THICKNESS RANGE 12.7 .50 MAX 3.25 [82.6] 291.3 11.47 MAX 21.04 [534.2] 76.2 3.00 133.3 5.25 2 Installation Instructions KRA212 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Phillips Screwdriver Adjust Destornillador Phillips Ajustar Kreuzschlitzschraubendreher Einstellen Chave de fendas Phillips Ajustar Cacciavite a stella Regolare Kruiskopschroevendraaier Afstellen Tournevis à pointe cruciforme Ajuster Open-Ended Wrench Remove Llave de boca Quitar Gabelschlüssel Entfernen Chave de bocas Remover Chiave a punte aperte Rimuovere Steeksleutel Verwijderen Clé à fourche Retirez By Hand Optional A mano Opcional Von Hand Optional Com a mão Opcional A mano Opzionale Met de hand Optie À la main En option Hex-Head Wrench Security Wrench Llave de cabeza hexagonal Llave de seguridad Sechskantschlüssel Sicherheitsschlüssel Chave de cabeça sextavada Chave de segurança Chiave esagonale Chiave di sicurezza Zeskantsleutel Veiligheidssleutel Clé à tête hexagonale Clé de sécurité 3 KRA212 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" (included) 1/8" (included) PARTS A (1) [KRA212 assembly] B (4) M4x14mm E (1) 5/16-18 x 1" H (1) [metallic ring] C (4) M4x25mm F (1) [UHMW washer] J (1) [pivot ring] L (1) 3/16" 4 D (4) M10x5.3x10 G (1) [spacer] K (1) [pocket washer] Installation Instructions KRA212 Assembly And Installation K2C100 Disassembly 3 1. Remove top cap from column. (See Figure 1) 2. Loosen clamp and slide mount assembly off of column. (See Figure 1) remove and discard NOTE: Set aside column and desk clamp for reuse. 1 remove and discard remove and reuse coupler (discard) 2 2 remove and reuse Figure 2 K2C200 Conversion 1. Slide KRA212 assembly (A) onto desk mount column. (See Figure 3) 2. Tighten clamp on back of KRA212 assembly (A) to secure at desired height. (See Figure 3) 3. Replace top cap onto column. (See Figure 3) Figure 1 3. Remove arm from column clamp by removing button head cap screw and additional hardware. (See Figure 2) NOTE: Set aside arm for reuse. Discard removed hardware and coupler may be discarded if it will not be converted back to a single arm mount in the future. 2 3 (A) 1 Figure 3 5 KRA212 Installation Instructions (E) 4 (F) (G) (K) removed arm (J) (H) (A) 5 removed clip and screw Figure 4 4. Use 5/16-18 x 1" button head cap screw (E), UHMW washer (F), spacer (G), pocket washer (K), pivot ring (J), and metallic ring (H) to secure removed arm onto vacant pin on KRA212 assembly. (See Figure 4) 5. Attach removed cable clip and screw to bottom of KRA212 coupler. (See Figure 4) 6. Refer to K2 Series installation instructions to install converted mount to desk, install displays, manage cables and make adjustments. 6 Installation Instructions KRA212 7 KRA212 Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002359 Rev00 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 03/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No. 1 on 12/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477