Download Havis C-SM-SA car kit
Transcript
INSTALL INSTRUCTIONS C-SM SERIES ANGLED HEAVY DUTY CONSOLE & ACCESSORIES TOOLS REQUIRED: Standard socket set w/ 6”extension Metric socket set w/ 6” extension Standard wrench set Monitor Platform (C-SM-MMP) Metric wrench set Torx bit set w/ driver Keyboard/Laptop Platform (C-SM-SA-1) Angled Heavy Duty Console (C-SM-830 or 1225) Pentex Printer Mount (C-PMS) Slide ¼” nuts into extrusion. This can be done on inside of console at top of extrusion. Tunnel Plate (C-TMW-xx) (Part # varies depending on vehicle type) Console Extension (C-SM-600, 800 or 1200) C-SM_INST_9-10 Always! ¾ Read all instructions before installing any Havis, Inc. products. ¾ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes! ¾ Use hardware provided with install kit Height Adjustment Figure #1 SUB ASSEMBLY: 1. Install Tunnel Mount into vehicle. (See Tunnel Mount specific install instructions.) 2. Determine desired height of console and console accessories prior to mounting in vehicle. INSTALLATION: 1. ADJUST CONSOLE HEIGHT: (See Figure #1) • To adjust height remove carriage bolts on side of console. • Mount necessary accessories to side of console. (Monitor platform, keyboard/laptop platform, printer, etc. See instructions below.) • With all accessories and height determined, re-attach carriage bolts and nuts to console. Figure #2 2. ATTACH MONITOR PLATFORM: (See Figure #2) • Mounting platform attaches to side of console using supplied carriage bolts and serrated nuts. • Monitor mounting platform will mount to front row of holes on console. • Attach C-UMM-101 and C-MM-XXX brackets to monitor platform prior to attaching to console. Note: Prior to mounting accessories to side of Angled Heavy Duty console be sure to adjust height. Mounts to sides of Console 3. ATTACH KEYBOARD/LAPTOP PLATFORM: Figure #3 (See Figure #3) • • • • • Mounting platform attaches to side of console using supplied carriage bolts and serrated nuts. When using platform for a keyboard, mount on rear rows of holes on console. When using platform for a laptop, you have the option of using any row of holes for desired height. Attach tilt / swivel, keyboard/laptop mount to swing arm assembly. RE: C-MD-202, C-KBM-101 (sold separate) Note: Prior to mounting accessories to side of Angled Heavy Duty console be sure to adjust height. Mounts to sides of Console C-SM_INST_9-10 Figure #4 Mounting Hardware Figure #5 Mounts to Angled Heavy Duty console A spare plastic end cap is provided in case you choose not to attach consoles together Tunnel Plate Hardware 4. ATTACH PENTEX PRINTER BRACKET: (See Figure #4) • Printer bracket attaches to front side of console. • When mounted properly, printer housing will slide toward passenger side seat. • Attach to Angled Heavy Duty console using supplied screws and Keps nuts. 5. MOUNT CONSOLE TO TUNNEL PLATE: • Slide ¼-20 x ¾” bolts into slots of Tunnel Plate. • Place Angled Heavy Duty console over ¼” bolts. • Position console and attach to Tunnel using ¼-20 serrated nuts. 6. ATTACH CONSOLE EXTENSION: (C-SM-600, 800, 1200 see Figure 5) • With Angled Heavy Duty console attached to Tunnel, position and attach 6” console extension. **A spare plastic end cap is provided in case you choose not to attach consoles together. Simply peel and stick to console end plate if desired. • Slide (2) ¼-20 x ¾” hex head bolts into slots of Tunnel Plate. • Place console extension and bolt down using ¼-20 serrated nuts. • Connect opposite end-to-end plate of Angled Heavy Duty housing. (Slot to slot). Adjust height as desired. • Wire and install control heads and accessories. C-SM_INST_9-10 C-SM-SA-1-HD ASSEMBLY WITH C-MD-200 SERIES 5/16-24 JAM NUT GSM30070 5/16-24 CONICAL NUT GSM30160 5/16" BELLEVILLE WASHER GSM31091 C-MD-203 TOP REMOVED FOR CLARITY PLASTIC WASHER COMES WITH C-MD-200 ASSEMBLY CM003105 METAL PLATE CM003103-1 COMES WITH C-MD-200 ASSEMBLY SWING ARM 1/4-20 X 1-1/2" LG BOLT CM86504 STANDARD C-SM-SA-1-HD ASSEMBLY 5/16-24 JAM NUT GSM30070 5/16-24 CONICAL NUT GSM30160 5/16" BELLEVILLE WASHER GSM31091 C-3075-3 OR ANY OTHER NON C-MD-200 SERIES ASSEMBLY METAL PLATE GSM31020 COMES WITH SWING ARM ASSEMBLY PLASTIC WASHER CM003105 LARGE COMES WITH SWING ARM ASSEMBLY SWING ARM 1/4-20 X 1-1/2" LG BOLT CM86504 C-SM-SA-1 ASSEMBLY WITH C-MD-200 SERIES 5/16-24 JAM NUT GSM30070 5/16-24 CONICAL NUT GSM30160 5/16" BELLEVILLE WASHER GSM31091 C-MD-203 TOP REMOVED FOR CLARITY METAL PLATE CM003103-1 COMES WITH C-MD-200 ASSEMBLY PLASTIC WASHER CM003105 COMES WITH C-MD-200 ASSEMBLY STAINLESS STEEL FENDER WASHER (SPACERS) GSM31059 SWING ARM 1/4-20 X 1-1/2" LG BOLT CM86504