Download Fujitsu PRIMERGY RX300 S7
Transcript
PRIMERGY RX300 S7 System configurator and order-information guide June 2012 Contents Instructions Configuration diagram Configurator 0 System software I Basic unit II Processor III Memory IV Graphics V Accessible drives VI Hard disk drives VII PCI Controller VIII Communication/Network IX System Management Products (RemoteView) X Miscellaneous XI Country specific power cord Change report PRIMERGY Server System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 Instructions This document contains basic product and configuration information that will enable you to configure your system via PC-/System-Architect. Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to adjust your specific requirements. The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. Section III Memory, example There are X memory slots which can be equipped with XXX MB. It is permissible to make up to X passes through the memory upgrade options S26361-XXX-XXX Memory XXX MB S26361-XXX-XXX Memory XXX MB max. X times per system max. X times per system X times In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x Please note that there are information symbols which indicate necessary information. For further information see: http://ts.fujitsu.com/products/standard_servers/index.html (internet) https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx (extranet) Fujitsu Technology Solutions x86 PRIMERGY Serve 2 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 Configuration diagram PRIMERGY RX300 S7 System unit ( I ) with up to 6x 3.5" Hard disk drives Motherboard Memory CPU1 front side Bay for LocalView LCD LSD 2 USB Air channel VGA, LAN Frontpanel Bay for 5,25"x 0,5" SATA-BR or DVD-ROM/RW ( Channel A + B + C ) Bank 1 (4 Modules) Bank 2 (4 Modules) Bank 3 (4 Modules) Xeon DP Memory CPU2 ( Channel D + E + F) Bank 1 (4 Modules) Bank 2 (4 Modules) Bank 3 (4 Modules) Memory (III ) Xeon DP Processor ( II ) Accessible drives ( V ) rear side Fan 1 - Fan 5 1. PSU Needs space for 2 hard disk drives! 2. PSU Redundant Fans are standard! Redundant power supply option 3.5"x1,6" Backup drive option Modular RAID Support Raid Card for IME, Raid 0 / 1E Raid Card for Raid 5 Low-profile extension slots for: SCSI Controller for backup( VII ) SAS Disk Array ( VIII ) Communication/Network ( IX ) Miscellaneous ( X ) Hard disk drives ( VI ) 3.5" SAS/SATA 3.5"x1" SAS or SATA Slot 6 PCIe-3 x16, 390mm @ CPU2 3.5"x1" SAS or SATA Slot 5 PCIe-3 x16, 390mm @ CPU2 Slot 4 PCIe-3 x8, max. 390mm @ CPU1 3.5"x1" SAS or SATA Possibility to install PCIe x16 cards Slot 3 PCIe-3 x8, max. 390mm @ CPU1 3.5"x1" SAS or SATA Slot 2 PCIe-3 x8, max. 312mm @ CPU1 3.5"x1" SAS or SATA Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored Dedicated for modular on-board LAN-Controller Slot 7 PCIe-3 x8, max. 168mm @ CPU1 3.5"x1" SAS or SATA Internal slot for modular RAID-Controller Key: Included in basic unit Option One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit. Fujitsu Technology Solutions x86 PRIMERGY Serve 3 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 Configuration diagram PRIMERGY RX300 S7 System unit ( I ) with up to 4, 8, 12 or 16x 2.5" Hard disk drives Motherboard Memory CPU1 front side Bay for LocalView LCD LSD 2 USB Air channel VGA, LAN Frontpanel Bay for 5,25"x 0,5" SATA-BR or DVD-ROM/RW ( Channel A + B + C ) Bank 1 (4 Modules) Bank 2 (4 Modules) Bank 3 (4 Modules) Xeon DP Memory CPU2 ( Channel D + E + F) Bank 1 (4 Modules) Bank 2 (4 Modules) Bank 3 (4 Modules) Memory (III ) Xeon DP Accessible drives ( V ) Processor ( II ) Needs space for 4 2.5" hard disk drives! 3.5"x1,6" rear side Fan 1 - Fan 5 1. PSU 2. PSU Redundant Fans are standard! Backup drive option 1 Redundant power supply option Needs space for 8 2.5" hard disk drives! 5.25"x1,6" Modular RAID Support Raid Card for IME, Raid 0 / 1E Backup drive option 2 Raid Card for Raid 5 Low-profile extension slots for: SCSI Controller for backup( VII ) SAS Disk Array ( VIII ) Communication/Network ( IX ) Miscellaneous ( X ) Hard disk drives ( VI ) 2.5" SAS/SATA Up to 4 blocks with 4 HDDs Slot 6 PCIe-3 x16, 390mm @ CPU2 2.5" SAS or SATA 2.5" SAS or SATA Slot 5 PCIe-3 x16, 390mm @ CPU2 2.5" SAS or SATA Slot 4 PCIe-3 x8, max. 390mm @ CPU1 2.5" SAS or SATA Possibility to install PCIe x16 cards Slot 3 PCIe-3 x8, max. 390mm @ CPU1 2.5" SAS or SATA Slot 2 PCIe-3 x8, max. 312mm @ CPU1 2.5" SAS or SATA Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored Dedicated for modular on-board LAN-Controller 2.5" SAS or SATA 2.5" SAS or SATA Slot 7 PCIe-3 x8, max. 168mm @ CPU1 Internal slot for modular RAID-Controller Key: Included in basic unit Option One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit. Fujitsu Technology Solutions x86 PRIMERGY Serve 4 of 28 PRIMERGY-Software Configurators and Release Lists PRIMERGY RX300 S7 Status 2012-05-30 Start PRIMERGY RX300 S7 SW Configurator 32 bit with OEM-Software for PRIMERGY Server without OEM-Software for PRIMERGY Server OEM- SW is bound to HW and is not allowed to be ordered separately. Exception: VMware SW VMware-Software - VirtualCenter Management Server for any server released for Windows Server 2003 - Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems - ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way For all SW products please refer to the corresponding software configurator accessible via the Extranet under Configuration & Tools, -All configurations, -Software, URL see below. Linux - Software **) - Open Enterprise Server ***) - SuSE Linux ES (OEM): LO - Red Hat EL (OEM): LO Microsoft - Windows Server 2008 Server Licenses - Windows Server 2008 Enterprise - Windows Server 2008 Standard - Windows Server 2008 Foundation - Windows Web Server 2008 PRIMECLUSTER *) - Clustering - Load Balancing Microsoft - Windows Server 2008 Client Access Licenses - Windows Server 2008 Device CAL - Windows Server 2008 User CAL - Windows Server 2008 Remote Desktop Services Device CAL - Windows Server 2008 Remote Desktop Services User CAL SCO - Software: **) - SCO OpenServer (only 1- and 2-way Tower servers) - SCO UnixWare (only 1-, 2, and 4-way Tower and Rack servers) x10sure *) x10sure Control Nodes and Compute Nodes Windows Server 2003 Compute Nodes for PRIMERGY BX600, RX/TX MultiPath, Duplex Data Manager (DDM) W2K; W2K3 Linux (W-DDM) for PRIMERGY except all mono PY systems Details eg. version numbers are published on the page referred to Manageability Software: V**) - iRMC advanced Pack - RemoteView Software - RemoteView Service Board - RemoteView Diagnosis - RemoteDeploy *) Pay attention to the x10sure release and ordering information in the Extranet under https://ts.fujitsu.com/x10sure *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx **) Pay attention to release and order information in PRINCE -> Operating System https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx Backup-Software / Application-Software: U - ARCserve - openSM2 ***) Supply over distribution or procurement from FSC VP BC Software You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: for internal users: for partners: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx Continue with PRIMERGY HW configurator Fujitsu Technology Solutions x86 PRIMERGY Server PRIMERGY-Software Configurators and Release Lists PRIMERGY RX300 S7 Status 2012-05-30 Start PRIMERGY RX300 S7 SW Configurator 64 bit (EM64T / IA64) with OEM-Software for PRIMERGY Server without OEM-Software for PRIMERGY Server OEM- SW is bound to HW and is not allowed to be ordered separately. Exceptions: VMware SW, Citrix XenServer For all SW products please refer to the corresponding software configurator accessible via the Extranet under "Configuration & Tools, -All configurations, -Software, URL see below. VMware-Software - VirtualCenter Management Server for any server released for Windows Server 2003 - Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems - ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way Citrix XenServer / Essentials for XenServer - XenCenter Management Server for any server released for Windows 2000/XP/Vista and Server 2003/2008 - XenServer and Essentials for XenServer released for RX200S5, RX300S4/S5, RX600S4, BX620S4/S5, BX920S1 Microsoft Hyper-V Server and System Center - Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2 - Microsoft System Center Essentials Management Suite for any server released for Windows Server 2008 SP2 - Microsoft Hyper-V Server 2008 R2 Microsoft - Windows Server 2008 R2 Server Licenses - Windows HPC Server 2008 R2 Suite - Windows Server 2008 R2 Datacenter - Windows Server 2008 R2 Enterprise - Windows Server 2008 R2 Standard - Windows Web Server 2008 R2 only EM64T Microsoft - Windows Server 2008 Server Licenses - Windows Server 2008 Datacenter - Windows Server 2008 Enterprise - Windows Server 2008 Standard - Windows Web Server 2008 PRIMECLUSTER *) - Clustering - Load Balancing Microsoft - Windows Server 2008 Client Access Licenses - Windows Server 2008 Device CAL - Windows Server 2008 User CAL - Windows Server 2008 Remote Desktop Services Device CAL - Windows Server 2008 Remote Desktop Services User CAL only Linux - Software *) **) # Open Enterprise Server ***) - SuSE Linux ES (OEM): LO - Red Hat EL (OEM): LO QuickTransit (QT) only Transition Solaris Apps. EM64T to x86-64 PY with Linux MultiPath, Duplex Data EM64T Manager (DDM) Windows, Linux (W-DDM) Details eg. version numbers are published on the page referred to Manageability Software: V**) - iRMC advanced Pack only - RemoteView Software EM64T - RemoteView Service Board - RemoteView Diagnosis - RemoteDeploy *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx **) Pay attention to release and order information in PRINCE -> Operating System https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx ***) Supply over distribution or procurement from FSC VP BC Software You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: for internal users: for partners: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx Continue with PRIMERGY HW configurator Fujitsu Technology Solutions x86 PRIMERGY Server System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 Start PRIMERGY RX300 S7 I Section Basic unit System unit consisting of: * 2U Housing without power supply modules * Basic units with: - 2 Hot-Plug Power Supply Bays - 5 Fans (full redundancy) * SAS Backplane for 6x 3.5" HD or SAS Backplanes for 4, 8, 12 or 16x 2.5" HD with cable connection to on-board or modular RAID Controller * Drives/Bays - 6 bays 1" for hot plug 3.5" HD (1" high) or 4, 8, 12 or 16 bays for hot plug 2.5" HD - 1 bay for 3.5" and 1.6" high Backup device, consumes 2 bays for 3.5" HD for basic unit 6x 3.5" HD not possible for basic unit with 12 or 16 x 2,5" HD - 1 bay for 5.25" and 1.6" high Backup device, not possible for basic unit 6x 3.5" HD for basic unit with 12 or 16 x 2,5" HD - 1 bay SATA-CD- or DVD-ROM 0,5" height (option) - 1 bay for opt. LocalView LC-Display * Integrated ServerView Diagnostics Technology ( Diagnosis LED`s ) for indication of internal failed components Systemboard D2939 with: * Up to two Xeon 4C, 6C & 8C CPU`s (Socket-R) with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU First CPU has to be selected for an orderable basic unit, * Chipset Intel® C600 Series (codenamed Patsburg) * 7 PCI slots: - 2x PCIe-3 x16 (both slots are connected to CPU 2 and are useable with configured 2nd CPU only!) - 4x PCIe-3 x8 (one notched to install x16 cards) - 1x PCIe-3 x8 (for internal modular RAID controller only) * 24 memory slots for max. 768GB RAM DDR3 available - Memory is divided into 12 DIMMs per CPU ( 4 channels with 3 slots per channel ) Possible max. configurations are: 24x 32GB LRDIMM (quad rank modules) = 768GB 24x 16GB RDIMM (dual rank modules) = 384GB 16x 8GB UDIMM (dual rank modules) = 128GB First Memory ( one module ) has to be selected for an orderable basic unit per CPU - Memory upgrade is possible module wise - Memory mirrroring is supported with 2 identical modules in channel A+B CPU 1 or D+E CPU 2 - Hot Spare Memory is supported with 3 identical modules in channel A+B+C CPU 1 or D+E+F CPU 2 - SDDC (Chipkill) is supported for memory modules, * Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board * iRMC S3 (integrated Remote Management Controller) on-board server management controller with dedicated 10/100/1000 Service LAN-port and integrated graphics controller. The Service LAN-port can be switched alternatively on standard Gbit LAN port 1 * Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller): 1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz (1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off) Interfaces at the rear: * 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared) * 1x VGA (15 pins) * 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup * 2x LAN RJ45, 1x Service-LAN RJ45 Interfaces on the front: * 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup * 1x VGA (15 pins) as an option * 1x Service-LAN RJ45 as an option Interfaces internal: * 1x released internal USB Interfaces for backup devices, * 1x USB 2.0 (UHCI) with 480MBit/s for dongle funcionality (uSSD memory), no USB wakeup * 1x SATA interface for DVD (only usable with 4x 2.5" HDD + DVD Option) * 4x SATA/SAS interface for 4 SATA/SAS HD`s or SAS Backup device * 2x USB 2.0 ports for internal USB redirection connected to BMC Software: * ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates * Documentation engl. (multilingual on CD) A Fujitsu Technology Solutions x86 PRIMERGY Serve 7 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 A Cables included in basic unit Connections Cable PRIMERGY RX300 S7 1. SATA DVD 2. SAS cables to HDDs 3. 1x cable for SAS signaling SAS SATA Note: Rack Mounting kit and Power Cord for RX300S7 is not included in the basic unit and has to be configured separately Rack version for 19'' racks with Basic unit with 2.5" HDD bays is modular expandable with various modules for backup devices integration or up to 16x 2.5" HDDs. Details and pictures see Section Va: Possible configuration options for basic units No PSU included in Base Unit Basic unit is without CPU and Memory For an orderable basic unit one CPU = first CPU and one memory = first memory has to be selected Basic unit with 6x 3.5" HDD bays fixed S26361-K1373-V101 Full redundancy cannot be guaranteed for a max. config. with e.g. two 135W CPUs with 450W PSUs. In this case SysArch will generate a warning and Power Safeguard will throttle CPUs in case of a PSU failure. So, power consumption will be limited to 450W. Basic unit with 2.5" HDD bays expandable S26361-K1373-V401 Basic unit with 8x 2.5" HDD bays fixed S26361-K1373-V201 Basic unit with 12x 2.5" HDD bays fixed S26361-K1373-V301 as soon as available (June 2012) S26113-F575-E10 S26113-F574-E10 S26113-F609-E10 450W PSU module platinum 800W PSU module platinum 800W PSU module -48V DC gold 1st or 2nd PSU for redundancy 1st or 2nd PSU for redundancy 1st or 2nd PSU for redundancy 94% efficiency (platinum) 94% efficiency (platinum) 92% efficiency (gold) uses hot plug PSU slot uses hot plug PSU slot uses hot plug PSU slot min. 1 / max. 2x per system min. 1 / max. 2x per system min. 1 / max. 2x per system S26113-F574-E99 * For later redundancy upgrade the following kit is available: Power Supply Dummy One 450W power supply module hot plug must be ordered if 1x PSU only no power cable included!!! occupies one bay for One 800W power supply module hot plug hot plug power supply no power cable included!!! max. 1x per system One 800W -48V DC PSU hot plug no power cable included!!! S26113-F575-L10 S26113-F574-L10 S26113-F609-L10 Please order appropriate power cord additionally: *For order completeness only Powercord for rack, 4m, grey, IEC320 C13->C14 connector T26139-Y1968-L10 Not shown in system architect Power Cord USA / Canada, 1.8m, grey T26139-Y1742-L10 Version > V9.2 Power Cord -48V DC, 4m, black T26139-Y4024-L10 S26361-F3552-E1 TPM Module Trusted Platform Module on Motherboard Use according to import restrictions S26361-F3552-L1 max. 1x per system TPM Module add-on kit for later integration (loose delivery) Trusted Platform Module on Motherboard Be aware of import restrictions! Use according to import restrictions Loose delivery for later max. 1x per system integration possible for customer. B Fujitsu Technology Solutions x86 PRIMERGY Serve 8 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 B PRIMECENTER Rack S26361-F2735-E175 RMK-F1_DI_CMA_QRL_LV S26361-F2735-E111 telescopic drop-in rail, full extr. Only for loose deliveries S26361-F2735-L175 RMK-F1_DI_CMA_QRL_LV 1-hand-mounting No mounting in racks possible for loose delivery RMK - 1 pair consisting of max. 1x per system No Rackmount-Kit option - vario carrier length variable S26361-F2735-L10 Adapter angle PC/DC-Rack, till 50Kg with quick release lever support - telescopic drop-in rails with CMA adapter 1x per system necessary for mounting RMKs in asymmetrical racks C S26361-F2735-L7 S26361-F4530-E11 Mounting 1U server in S26361-F4530-E10 Mounting in Lateral cable management can only be mounted in asymmetrical PRIMECENTER asymmetrical racks symmetrical racks S2 or new M1 racks in 1U above RMK with 1U support bracket (no support bracket needed) S26361-F2735-E71 Lateral cable management S26361-F2735-E82 2U cable management arm (CMA) Cable Management Arm (CMA) can for 2U servers or higher for 2U Server CMA adapter - for asymmetrical racks PRIMECENTER S2 or M1 - 1 bracket PC Rack asym. 1x per system only be used for FTS RMKs with - for symmetrical racks M1 or 3rd party racks Fujitsu racks 1x per system S26361-F2735-L82 Cable management arm for 2U Server or higher for loose delivery can only be mounted at RMK with CMA adapter for loose delivery SNP:SY-F1647E301-P Installation ex works for one server or subsystem. Hereby the rack will be delivered "Rack-mounting ex factory" completely pre-mounted and This service is to be ordered once all wired connections are tested. per installable server/storage With PCR S2 12U, 24U, 38U and subsystem, in order to get the PRC M1 16U, 24U, 42U: server/storage subsystem Systems and components mounted into the racks. will be delivered installed in the rack In case of the 46 U PCR S2 With PCR S2 racks 46U: this service has to be ordered, Systems and components to get the mounting kits and the will be delivered separately cables installed. To be ordered only together with a PRIMECENTER rack PCR S2 e.g. S26361-K826-V10x new PCR M1 e.g. S26361-K827-Vxxx refer PCR S2 or M1 rack configurator max. 1x per System PRIMERGY Classic 19" rack is not supported C Fujitsu Technology Solutions x86 PRIMERGY Serve 9 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 C II Section Processor There are 2 processor sockets available. The first socket must always be equipped with the first CPU which can be selected via configurator It is also possible to upgrade a dual-processor system later on with a second CPU Both PCIe-3 x16 slots are connected to CPU 2 and are useable with configured 2nd CPU only! Two processors with different clock frequencies are not possible A multi-processor operating system is required for a dual-processor system. Note: Max. DDR3 Bus Speed depends on: Max. two CPU`s can be selected per basic unit One of following CPU´s has to be selected as first CPU for an orderable basic unit Optional second CPU has to be the same type like the first CPU - max. DDR3 Bus Speed from the CPU and - max. DDR3 Memory Speed and - max. memory modules on one memory channel Basic 4C CPU's - 1x 64-bit Intel Xeon (10MB Smart Cache) 1066 MHz DDR3 Bus; 6,40 GT/s QPI Bus and passive heat sink occupies socket for one CPU Xeon E5-2603 4C/4T 1.80GHz 10MB 6.40GT/s 1066MHz 80W Xeon E5-2609 4C/4T 2.40GHz 10MB 6.40GT/s 1066MHz 80W S26361-F3685-E180 S26361-F3685-E240 Standard Turbo 6C CPU's - 1x 64-bit Intel Xeon (15MB Smart Cache); Hyper-Threading (HT); 1333 MHz DDR3 Bus; 7,20 GT/s QPI Bus and passive heat sink occupies socket for one CPU Xeon E5-2620 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 95W Xeon E5-2630 6C/12T 2.30GHz 15MB 7.20GT/s 1333MHz 95W Xeon E5-2640 6C/12T 2.50GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3676-E200 S26361-F3676-E230 S26361-F3676-E250 Advanced Turbo+ 8C CPU`s - 1x 64-bit Intel Xeon (20MB Smart Cache); Hyper-Threading (HT); 1600 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink occupies socket for one CPU Xeon E5-2650 8C/16T 2.00GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3686-E200 Xeon E5-2660 8C/16T 2.20GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3686-E220 Xeon E5-2665 8C/16T 2.40GHz 20MB 8.00GT/s 1600MHz 115W Xeon E5-2670 8C/16T 2.60GHz 20MB 8.00GT/s 1600MHz 115W S26361-F3686-E240 S26361-F3686-E260 Xeon E5-2680 8C/16T 2.70GHz 20MB 8.00GT/s 1600MHz 130W Xeon E5-2690 8C/16T 2.90GHz 20MB 8.00GT/s 1600MHz 135W S26361-F3686-E270 S26361-F3686-E290 On special release only Frequency Optimized Turbo 2C, 4C & 6C CPU`s - 1x 64-bit Intel Xeon (5/10/15MB Smart Cache); Hyper-Threading (HT); 1600 MHz DDR3 Bus; 6,40/7,20 GT/s QPI Bus and passive heat sink occupies socket for one CPU Xeon E5-2637 2C/4T 3.00GHz 5MB 6.40GT/s 1600MHz 80W Xeon E5-2643 4C/8T 3.3GHz 10MB 6.40GT/s 1600MHz 130W Xeon E5-2667 6C/12T 2.90GHz 15MB 7.20GT/s 1600MHz 130W S26361-F3687-E300 S26361-F3687-E330 S26361-F3687-E290 Low Power 4C/6C/8C CPU's - 1x 64-bit Intel Xeon (15/20MB Smart Cache); Hyper-Threading (HT); 1333/1600 MHz DDR3 Bus; 7,20/8,00 GT/s QPI Bus and passive heat sink occupies socket for one CPU Xeon E5-2630L 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 60W Xeon E5-2650L 8C/16T 1.80GHz 20MB 8.00GT/s 1600MHz 70W S26361-F3688-E200 S26361-F3688-E180 D Fujitsu Technology Solutions x86 PRIMERGY Serve 10 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 D IV Section Graphics Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller): 1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz (1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off) S26361-F2571-E26 Optional Front-VGA for Onboard Controller only consists of internal cable and front VGA connector max. 1x per system The hight end optional NVIDIA NVS300 graphic card offers dual head operation and fully 3D video support. The cables for either two times DVI-I or VGA (cable kit) connections are part of the delievery. Remote Video direction via iRMC must be disabled. This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot. Only one card per server is allowed. S26361-F2748-E637 PY VGA LP card 256MB PCI-e x1 NVIDIA NVS300 512 MB PCIe-x1 Connectors: 1x LFH 59 cable kit for 2x DVI or 2x VGA cable kits included Dual head + professional 2-D + 3-D supported for Windows OS native driver support for Linux OS low profile bracket max. 1x per system S26361-F2748-L637 PY VGA LP card 512MB PCI-e x1 for loose delivery E Fujitsu Technology Solutions x86 PRIMERGY Serve 11 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 E III Section Memory - There are 12 memory slots per CPU for max. 384GB LRDIMM (12x 32GB 4R) 192GB RDIMM (12x 16GB 2R) 32GB UDIMM (8x 4GB) => max. 768GB for two CPU`s ( 384GB per CPU ), using LRDIMM - The memory area is divided into 4 channels per CPU with 3 slots per channel - Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2, slot 3 belongs to memory bank 3 Registered, LR DIMMs and unbuffered memory modules can be selected No mix of registered, load reduced and unbuffered modules allowed. Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type. Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed). In a 2 DIMMs per channel configuration, following frequencies are supported: - 1.5V - 1600MHz max (depending on CPU, special memory modules) - 1.35V - 1333MHz max (depending on CPU) In a 3 DIMMs per channel configuration, memory will operate at 1.5V only. SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only 1.) In the "Independent Channel Mode" is following configuration possible Channels can be populated in any order in Independent Channel Mode. All four channels may be populated in any order and have no matching requirements. All channels must run at the same interface frequency but individual channels may run at different DIMM timings (RAS latency, CAS latency, and so forth) No mix of registered, load reduced and unbuffered modules allowed. 2.) "Rank Sparing Mode" configuration - Within a memory channel, one rank is a spare of the other ranks. The Spare Rank is held in reserve and is not available as system memory For the effective memory capacity, please refer to the spreadsheet below. The BIOS is set to the rank sparing setting. Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel This mode is not supported by unbuffered memory modules 3.) "Performance Mode" configuration - In this configuration, the memory module population ex factory is spread across all channels. The BIOS is set to the max. performance for memory. Minimum configuration is: 4x identical modules 4.) In the "Mirrored Channel Mode" is following configuration possible - Each memory bank can optionally be equipped with 4x registered or load reduced or unbuffered DDR3 modules In each memory bank channel A and B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be equipped with identical modules for mirrored channel mode. In channel B / D is always the mirrored memory of channel A / B of CPU 1 In channel F / H is always the mirrored memory of channel E / G of CPU 2 Minimum configuration is: 4x identical modules This mode is not supported by unbuffered memory modules F Fujitsu Technology Solutions x86 PRIMERGY Server 12 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 F S26361-F3694-E10 Independent Mode Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined Requires min 1 memory Module per CPU S26361-F3694-E1 Rank Sparing Mode Installation BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shown in System Memory. For effective capacity within a channel, please have a look below. 1x per CPU Supported for RDIMM / LRDIMM only. Requires min 2x 1R/2R or 1x 4R modules per CPU S26361-F3694-E2 Performance Mode Installation BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used. Multiple of 4 identical modules to be configured per CPU S26361-F3694-E3 Mirrored Channel Mode Installation as soon as available BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data Supported for RDIMM / LRDIMM only. Multiple of 4 identical modules to be configured per CPU Effective Memory capacity / Rank Sparing Mode, 1 Channel populated UDIMM RDIMM LRDIMM 2GB 1R 2GB 2R 4GB 1R 8GB 2R 16GB 2R 16GB 4R 32GB 4R 1DPC na na na na na 12GB 24GB 2DPC na na 4GB 12GB 24GB 28GB 56GB 3DPC na na 8GB 20GB 40GB 40GB 80GB Minimum one memory module or order code per CPU = first memory Note 1.) Unbuffered Memory (UDIMM) no SDDC (chipkill) support Max. DDR3 memory speed depends on the memory configuration - one DDR3 unbuffered ECC mem. Module, 1.35V (No of mem modules per channe) as well as on the CPU type. Choose up to 8 order codes per CPU 2GB (1x2GB) 1Rx8 L DDR3-1600 U ECC 4GB (1x4GB) 2Rx8 L DDR3-1600 U ECC The memory channel with the lowest speed defines the speed S26361-F3694-E513 S26361-F3694-E514 of all CPU channels in the system, also for the channels of the second CPU if configured. Registered Memory (RDIMM) no SDDC (chipkill) support For real memory speed (depending on memory type / population), - one DDR3 registered ECC mem. Module, 1.35V please check the spreadsheet "Memory speed" below No mix with any other types of memory modules possible Choose up to 12x for 1R/2R or 8x for 4R per CPU For performance reasons, we do not recommend to configure more than 8 DIMMs per CPU 4GB (1x4GB) 2Rx8 L DDR3-1600 R ECC S26361-F3695-E514 Registered Memory (RDIMM) with SDDC (chipkill) support 8/12x per - one DDR3 registered ECC mem. Module, 1.35V CPU, max. 1333MHz supported with up to 2DPC (8 modules/CPU) 2/3 modules Choose up to 12 order codes per CPU per channel 4GB (1x4GB) 1Rx4 L DDR3-1333 R ECC 8GB (1x8GB) 2Rx4 L DDR3-1333 R ECC Mix of memory modules is only possible within the same group S26361-F3696-E514 S26361-F3696-E515 new due to supply new due to supply Registered Memory (RDIMM) with SDDC (chipkill) support - one DDR3 registered ECC mem. Module, 1.35V 1600MHz supported with up to 2DPC (8 modules/CPU) at 1.5V Choose up to 12 order codes per CPU 4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC S26361-F3697-E514 8GB (1x8GB) 2Rx4 L DDR3-1600 R ECC 16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E515 S26361-F3697-E516 Load Reduced Memory (LRDIMM) with SDDC (chipkill) support - one DDR3 load reduced ECC mem. Module, 1.35V Choose up to 12 order codes per CPU 16GB (1x16GB) 4Rx4 L DDR3-1333 LR ECC 32GB (1x32GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E516 S26361-F3698-E517 as soon as available as soon as available G Fujitsu Technology Solutions x86 PRIMERGY Server 13 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 Memory Configuration PRIMERGY RX300 S7 Each CPU offers 12 Slots for DDR3 Memory Modules organised in 3 Banks and 4 Channels. If you need more than 12 Slots you have to configure the 2nd CPU. Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below). There are 3 different kinds of DDR3 Memory Modules available: UDIMM / RDIMM and LRDIMM UDIMM / RDIMM / LRDIMM offer different functionality. Mix of UDIMM / RDIMM / LRDIMM is not alloved. If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V Mode Configuration UDIMM RDIMM RDIMM Application LRDIMM x4 x8 x8 SDDC (chipkill) support any no no yes Independant Channel 1, 2 or 3 Modules per Bank yes yes yes Mode Mirrored Channel Mode *) 4 identical Modules / Bank no no yes Performance Mode 4 identical Modules / Bank yes yes yes Rank Sparing Mode *) min. 2 Ranks / Channel no no yes *) For the delivery ex works the system will be prepared with dedicated BIOS setting. Capacity Min. Memory per CPU Max. Memory per CPU Max. Memory per System Configuration 1 Module / CPU 8/12 Modules / CPU 16/24 Modules / System detect multi-bit errors offers max. flexibility, upgradeability, capacity use UDIMM modules for lowest cost offers maximum security offers maximum performance and capacity balances security and capacity UDIMM RDIMM LRDIMM 1x2GB 1x4GB 1x 16GB 8x4GB 12x16GB 12x 32GB 64GB 192GB 768GB Notes with one CPU with one CPU if second CPU is configured Memory-Speed: Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU The memory channel with the lowest speed defines the speed of all CPU channels in the system Mem. Speed provided by CPU Real maximum memory-bus speed depending on CPU type, memory configuration (DPC) and voltage setting (BIOS) UDIMM 1600MHz Voltage setting (BIOS) 1.5V [default] 1 2 DPC CPU with 1600MHz DDR3 Bus 1333 RDIMM 1600MHz 1.35V 3 1 2 1.5V [default] 3 1 2 3 LRDIMM 1333MHz 1.35V 1 2 1.5V [default] 3 1 2 3 1.35V 1 2 DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC 1333 1600 - 1066 - 1333 1066 - 1600 1600 1066 1333 1333 - - 1333 1333 1066 1066 1066 - 3 DPC - CPU with 1333MHz DDR3 Bus 1333 1333 - 1066 1066 - 1333 1333 1066 1333 1333 - 1333 1333 1066 1066 1066 - CPU with 1066MHz DDR3 Bus 1066 1066 - 1066 1066 - 1066 1066 1066 1066 1066 - 1066 1066 1066 1066 1066 - 1R - Single Rank 2R - Dual Rank 4R - Quad Rank on special release as soon as available 1DPC = 1 DIMM per Channel 2DPC = 2 DIMM per Channel 3DPC = 3 DIMM per Channel Configuration hints: - The memory sockets on the systemboard offer a color coding: Bank I black sockets Bank II blue sockets Bank III green sockets - A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below) Bank I on CPU 1/2 up to 4 memory modules connected to Channel A - H on the 1st/2nd CPU Bank II on CPU 1/2 up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU Bank III on CPU 1/2 up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU (can not be populated by UDIMM or 4R RDIMM memory modules) - See below and next page for a detailed descriptions of the memory configuration supported. Fujitsu Technology Solutions x86 PRIMERGY Server 14 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 Channel C Channel D Channel E Channel F Channel G Channel H Bank I Data (black sockets) Bank II Data (blue sockets) Bank III Data (green sockets) Channel B Channel A 1. Independent Channel Mode Data Data Data Data Data Data Data optional, same type in Bank per CPU Data Data Data Data Data Data Data optional, any type Data Data Data Data Data Data Data 1st XEON CPU (4/6/8 Core) required required if 2nd CPU is configured -------- not used 2nd XEON CPU (4/6/8 Core) Independent Channel Mode allows all channels to be populated in any order Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system Channel C Channel D Channel E Channel F Channel G Channel H Bank I Data (black sockets) Bank II Data (blue sockets) Bank III Data (green sockets) Channel B Channel A 2. Mirrored Channel Mode Mirror Data Mirror Data Mirror Data Mirror Mirror Data Mirror Data Mirror Data Mirror Mirror Data Mirror Data Mirror Data Mirror 1st XEON CPU (4/6/8 Core) required required if 2nd CPU is configured optional, same type in Bank per CPU -------- not used 2nd XEON CPU (4/6/8) Core) Mirrored Channel Mode requires identical modules on channel A,B, C, D (1st CPU) or channel E, F, G and H (2nd CPU) 50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory If this mode is used, a multiple of 4 identical modules has to be ordered. Channel C Channel D Channel E Channel F Channel G Channel H Bank I Data (black sockets) Bank II Data (blue sockets) Bank III Data (green sockets) Channel B Channel A 3. Performance Channel Mode Data Data Data Data Data Data Data optional, same type in Bank per CPU Data Data Data Data Data Data Data optional, any type Data Data Data Data Data Data Data 1st XEON CPU (4/6/8 Core) required required if 2nd CPU is configured -------- not used 2nd XEON CPU (4/6/8) Core) Performance Channel Mode requires identical modules on all channels of each Bank per CPU. If this mode is used, a multiple of 4 identical modules has to be ordered. Fujitsu Technology Solutions x86 PRIMERGY Server 15 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 4. Rank Sparing Mode Channel C Channel D Channel E Channel F Channel G Channel H Bank I Spare (black sockets) Bank II Data (blue sockets) Bank III Data (green sockets) Channel B Channel A 1-Rank Memory modules (RDIMM) Spare Spare Spare Spare Spare Spare Spare optional, same type in Channel per CPU Data Data Data Data Data Data Data optional, any type Data Data Data Data Data Data Data 1st XEON CPU (4/6/8 Core) required required if 2nd CPU is configured -------- not used 2nd XEON CPU (4/6/8) Core) Channel B Channel C Channel D Channel E Channel F Channel G Channel H Channel A 2-Rank Memory modules (RDIMM) Bank I (black) R1 Spare R2 Data Spare Data Spare Data Spare Data Spare Data Spare Data Spare Data Spare Data Bank II (blue) R1 Data R2 Data Data Data Data Data Data Data Data Data Spare Data Spare Data Spare Data Bank III (green) R1 Data R2 Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data required required if 2nd CPU is configured optional, same type in Channel per CPU optional, any type -------- 1st XEON CPU (4/6/8 Core) not used 2nd XEON CPU (4/6/8) Core) Channel B Channel C Channel D Channel E Channel F Channel G Channel H Bank I (black) Channel A 4-Rank Memory modules (LRDIMM) R1 R2 R3 R4 Spare Data Data Data Spare Data Data Data Spare Data Data Data Spare Data Data Data Spare Data Data Data Spare Data Data Data Spare Data Data Data Spare Data Data Data R1 R2 R3 R4 Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Spare Data Data Data Spare Data Data Data Spare Data Data Data R1 R2 R3 R4 Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data required required if 2nd CPU is configured optional, same type in Channel per CPU Bank II (blue) Bank III (green) 1st XEON CPU (4/6/8 Core) optional, any type -------- not used 2nd XEON CPU (4/6/8) Core) Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel. The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above "Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max. available memory, e.g. 6 DIMMs will be spread across two channels, each with 3DPC Fujitsu Technology Solutions x86 PRIMERGY Server 16 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 G Va Section Possible configuration options for basic units Config 1: 6x or 4x 3.5” HDD + 3.5" DDS/RDX drive Is fixed due to selection of basic unit with: 6x 3,5" HDD bays fixed S26361-K1373-V101 Basic unit S26361-K1373-V401 with expandable Config 2: 4x 2.5” HDD S26361-F1373-E420 Available Upgrade kits for this configuration option: Upgrade kit to 8x 2.5" HDD S26361-F1373-L424 Upgrade kit to 12x 2.5" HDD S26361-F1373-L427 Upgrade kit to 4x 2.5" HDD + LTO S26361-F1373-L423 Basic unit S26361-K1373-V401 with Config 3: 4x 2.5” HDD + LTO expandable S26361-F1373-E430 Available Upgrade kits for this configuration option: Upgrade kit to 8x 2.5" HDD S26361-F1373-L436 Basic unit S26361-K1373-V201 with Config. 4: 8x 2,5" HDD bays fixed S26361-K1373-V201 Available Upgrade kits for this fixed configuration: Upgrade kit to 12x 2.5" HDD S26361-F1373-L247 Upgrade kit to 16x 2.5" HDD S26361-F1373-L248 Basic unit S26361-K1373-V401 with Config 5: 8x 2.5“ HDD + 3.5“ drive No Upgrade kit available! expandable S26361-F1373-E450 Basic unit S26361-K1373-V401 with Config 6: 8x 2.5” HDD + LTO expandable S26361-F1373-E460 no ODD and LSD bay available! No Upgrade kit available! Basic unit S26361-K1373-V301 with Config 7: 12x 2,5" HDD bays fixed S26361-K1373-V301 Available Upgrade kits for this fixed configuration: Upgrade kit to 16x 2.5" HDD S26361-F1373-L378 Basic unit S26361-K1373-V401 with Config 8: 16x 2.5” HDD no ODD and LSD bay available! No Upgrade kit available! expandable S26361-F1373-E480 Includes all necessary bezels, cages, backplanes and cables H Fujitsu Technology Solutions x86 PRIMERGY Serve 17 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 H Vb Section Accessible drives Setup RX300 S7 by ServerStart is supported with following configurations: no DVD, no CD: remote installation only ( PXE service & DHCP server required) built in CD/DVD or USB CD/DVD disk drive: UNC Network share reachable or USB Floppy connected USB Floppy, no CD/DVD: USB CD/DVD connected If installation is done locally, make sure you have external FDD available for driver installation. Following USB Components are available 1) USB DVD SM / Blu-Ray External SuperMulti Drive S26341-F103-L126 External Blu-Ray Drive S26341-F103-L127 2) USB Memorybird: MyUSBS A910 8GB, MLC Flash S26391-F6048-L208 MyUSBS A910 16GB, MLC Flash S26391-F6048-L216 as soon as available S26361-F3269-E2 S26361-F3641-E2 DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA all formats, DUAL/DL, DVD-RAM 6x BD-RW, 8x DVD, 24x CD 1x BD DL and all CD/DVD formats 0.5 x 5.25", black bezel 0.5 x 5.25" max. 1x per system max. 1x per system Only for basic unit V1xx S26361-F3324-E7 S26361-F3857-E7 Tape drive DDS Gen5 USB 3.5" RDX drive USB 3.5" internal 36GB, 3MB/s, USB 2.0 80-320GB, 25MB/s, USB 2.0 1.6 x 3.5", black bezel 1.6 x 3.5", black bezel within a tape cage incl. description (Ger/US) within a tape cage incl. description (Ger/US) cleaning cartridge without RDX cartridges occupies 2 x 1" hard disk bays occupies 2 x 1" hard disk bays max. 1x per system max. 1x per system S26361-F3324-E5 S26361-F3325-E2 S26361-F3857-E5 Tape drive DDS Gen5 USB 3.5" Tape drive DDS Gen6 USB 3.5" RDX drive USB 3.5" internal 36GB, 3MB/s, USB 2.0 Connector: USB "B" 80GB, 6MB/s, USB 2.0 Connector: USB "B" 80-320GB, 25MB/s, USB 2.0 Connector: USB "B" with USB cable incl. description (Ger/US) with USB cable incl. cleaning cartridge with USB cable incl. description (Ger/US) cleaning cartridge without data cartridge without RDX cartridges 1.6 x 3.5", black bezel 1.6 * 3.5", black bezel 1.6 x 3.5", black bezel max. 1x per system max. 1x per system max. 1x per system 1x Only for basic unit V4xx RDX cartridges must be ordered separately RDX 160GB = S26361-F3857-L160 RDX 320GB = S26361-F3857-L320 RDX 500GB = S26361-F3857-L500 RDX 1TB = S26361-F3857-L600 * 10x RDX160 = S26361-F3857-L169 10x RDX320 = S26361-F3857-L329 * as soon as available H Fujitsu Technology Solutions x86 PRIMERGY Serve 18 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 H SAS Controller for internal Backup Drives S26361-F3674-E1 For internal SAS Backup drives Onboard 4 port SAS Controller an additional 4-port SAS controller has to be configured LSI Patsburg B RAID 0, 1 & 10 no controller cache Only for basic unit V4xx SAS 1.0 (3Gb/sec) 4 internal ports PCIe x4 no PCI slot required max. 1x per system 1x S26361-F3561-E4 S26361-F3626-E2 S26361-F3627-E1 Tape drive LTO3HH Ultrium SAS Tape drive LTO4 HH SAS IBM V2 Tape drive LTO5HH Ultrium SAS 400GB, 60MB/s, SAS 3Gb 800GB, 120MB/s, SAS 6Gb 1500GB, 140MB/s, SAS 6Gb Connector: mini-SAS Connector: mini-SAS Connector: mini-SAS incl. SAS cable incl. cleaning cartridge incl. SAS cable incl. cleaning cartridge incl. SAS cable incl. cleaning cartridge without data cartridge without data cartridge without data cartridge 1.6 * 5.25", black bezel 1.6 * 5.25" 1.6 * 5.25" max. 1x per system max. 1x per system max. 1x per system I Fujitsu Technology Solutions x86 PRIMERGY Serve 19 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 I VI Section Hard disks drives Modular Raid controller is connected to internal HDDs For basic units V1xx up to 6 SAS 3.5" hard disks can be configured also in mixed configuration. If the option "Tape drive" is configured only 4 bays for hard disks are available Mixed configurations with Eco SATA drives and SAS drives are not allowed 3.5" SAS drives and 3.5" BC SATA drives can be mixed, but not used in one logical RAID volume 6x / 4x with Backup drive for basic unit V1xx S26361-F3700-E250 HD 250GB 7.2krpm 3.5" ECO 7200rpm,<9.0 ms, 8MB Cache SATA 6Gb/s Economy hot plug/hot replace tray max. 6x per system S26361-F3700-E500 HD 500GB 7.2krpm 3.5" ECO 7200rpm,<9.0 ms, 8MB Cache SATA 6Gb/s Economy hot plug/hot replace tray max. 6x per system S26361-F4005-E530 HD 300GB 15krpm 3.5" 15.000rpm,<4ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 6x per system S26361-F4005-E545 HD 450GB 15krpm 3.5" 15.000rpm,<4ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 6x per system S26361-F4005-E560 HD 600GB 15krpm 3.5" 15.000rpm,<4ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 6x per system S26361-F3670-E500 HD 500GB 7.2krpm 3.5" 7200rpm,<9.0 ms, 64MB Cache BC-SATA 6Gb/s hot plug/hot replace tray max. 6x per system S26361-F3294-E200 HD 2000GB 7.2krpm 3.5" 7200rpm,<9.0 ms, 8MB Cache BC-SATA 3Gb/s hot plug/hot replace tray max. 6x per system S26361-F3670-E200 HD 2000GB 7.2krpm 3.5" 7200rpm,<9.0 ms, 64MB Cache BC-SATA 6Gb/s hot plug/hot replace tray max. 6x per system S26361-F3670-E300 HD 3000GB 7.2krpm 3.5" 7200rpm,<9.0 ms, 64MB Cache BC-SATA 6Gb/s hot plug/hot replace tray max. 6x per system as soon as available S26361-F3670-E100 HD 1000GB 7.2krpm 3.5" 7200rpm,<9.0 ms, 64MB Cache BC-SATA 6Gb/s hot plug/hot replace tray max. 6x per system J Fujitsu Technology Solutions x86 PRIMERGY Serve 20 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 J No mix of 2.5" BC-SATA HDD and 2.5" 10K SAS HDD max 8x for V2xx, 12x for V3xx, 16x for V4xx S26361-F4555-E100 SSD SATA 100GB, MLC Solid State Disk SATA 3Gb/s Mainstream Perfomance hot plug/hot replace tray max. 8/12/16x per system S26361-F4555-E200 SSD SATA 200GB, MLC Solid State Disk SATA 3Gb/s Mainstream Perfomance hot plug/hot replace tray max. 8/12/16x per system S26361-F4555-E400 SSD SATA 400GB, MLC Solid State Disk SATA 3Gb/s Mainstream Perfomance hot plug/hot replace tray max. 8/12/16x per system S26361-F4541-E100 SSD 100GB SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4541-E200 SSD 200GB SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4541-E400 SSD 400GB SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F3708-E250 HD 250GB 7.2krpm 2.5" 7200rpm,<9,5ms, 64MB Cache BC SATA 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F3708-E500 HD 500GB 7.2krpm 2.5" 7200rpm,<9,5ms, 64MB Cache BC SATA 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F3708-E100 HD 1000GB 7.2krpm 2.5" 7200rpm,<9,5ms, 64MB Cache BC SATA 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4482-E573 HD 73GB 15krpm 2.5" 15000rpm,<4,5ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4482-E514 HD 146GB 15krpm 2.5" 15000rpm,<4,5ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4482-E530 HD 300GB 15krpm 2.5" 15000rpm,<4,5ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4482-E190 HD 900GB 10krpm 2.5" 10000rpm,<4,5ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4482-E130 HD 300GB 10krpm 2.5" 10000rpm,<4,5ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4482-E145 HD 450GB 10krpm 2.5" 10000rpm,<4,5ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system S26361-F4482-E160 HD 600GB 10krpm 2.5" 10000rpm,<4,5ms, 8MB Cache SAS 6Gb/s hot plug/hot replace tray max. 8/12/16x per system PCIe SSD (occupies PCIe slot), as soon as available S26361-F4522-E781 S26361-F4522-E121 PCIe-SSD 781GB MLC ioDrive2 781GB PCIe-SSD 1,2TB MLC ioDrive2 1.2 TB PCIe 2.0 PCIe x4, Low Profile max. 2 per system PCIe 2.0 PCIe x4, Low Profile max. 2 per system No mix of 781GB and 1.2TB SSD possible K Fujitsu Technology Solutions x86 PRIMERGY Serve 21 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 K VII Section Modular Raid 0/1, Raid5 for SAS or SATA HD`s. On-board Controller for max. 4x 2.5" SATA or SAS HD`s On board SATA Controller with 3 Gb/sec and up to 4x 2.5" SATA HDDs (no additional controller required) For up to 4x 2.5" SAS HDDs with RAID 0/1 functionality a Patsburg Upgrade Kit is required For all other HDD configurations a modular RAID-controller is required Following optional onboard SAS RAID can be selected for 4x2.5" HDDs or one SAS Tape device S26361-F3674-E1 Onboard 4 port SAS Controller LSI Patsburg B RAID 0, 1 & 10 no controller cache SAS 1.0 (3Gb/sec) 4 internal ports PCIe x4 no PCI slot required max. 1x per system For more than 4 hard disks or 6 Gb/sec one of the following modular RAID-controllers is required Modular Raid 0/1 controller with IME support for SAS/SATA This RAID controller supports max. 8 HDDs on internal SAS ports Modular Raid 5 controller for SAS/SATA RAID levels 0, 1, 10, 5, 50, 6 and 60 are supported. This RAID controller supports max. 16 HDDs combined with internal SAS expander The FBU is an option for the controller which can be used once per controller. If the FBU option has been choosen, the TFM Module is needed once per FBU. as soon as available S26361-F3554-E8 RAID Ctrl SAS 6G 8port internal Based on chip LSISAS2008 LSI MegaRAID no Cache, no BBU RAID 0, 1 & 10 S26361-F3554-E512 RAID Ctrl SAS 6G 8port internal Based on chip LSISAS2108 LSI MegaRAID 512MB Cache with ECC RAID 0, 1, 10, 5, 50, 6, 60 S26361-F3669-E1 RAID Ctrl SAS 6G 8port internal Based on chip LSISAS2208 LSI MegaRAID 1GB Cache with ECC RAID 0, 1, 10, 5, 50, 6, 60 Support for 3Gb/s and 6Gb/s optional BBU optional FBU SATA and SAS hard drives PCIe x8 Low-profile MD2 form factor max. 1x per system Support for 3Gb/s and 6Gb/s SATA and SAS hard drives PCIe x8 Low-profile MD2 form factor max. 1x per system Support for 3Gb/s and 6Gb/s SATA and SAS hard drives PCIe x8 Low-profile MD2 form factor max. 1x per system S26361-F3257-E216 Cache Battery Backup Unit with 16 cm cable set max. 1x per Controller 1x S26361-F3669-L660 RAID Key FastPath License Activation Key for 1 Controller S26361-F3669-L661 RAID Key CacheCade License Activation Key for 1 Controller Lose delivery FBU option S26361-F3669-L100 TFM Module for FBU option S26361-F3669-E100 TFM Module for FBU option max. 1x per Controller max. 1x per Controller S26361-F3669-L110 Flash Backup Unit with 25cm, 55cm, 70cm cable set max. 1x per Controller S26361-F3669-E125 Flash Backup Unit with 25cm cable set max. 1x per Controller L Fujitsu Technology Solutions x86 PRIMERGY Serve 22 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 L SAS-/SCSI-/ Fibre-Channel Controller Low Profile SAS controller for external backup drives S26361-F3628-E201 SAS Controller 6Gb/s 8 port LP LSI SAS9200-8e LP PCIe 2.0 x4, ext: 8 port max. 3x per system No mix and match of different FC or FCoE controllers possible. All controllers for the connection of external storage system are delivered without cables. For the configuration of external cabling see the configurator for external storage system. Fibre Channel Controller for external storage systems For Fibre Channel SAN also other componets like 4x S26361-F3631-E201 S26361-F3631-E202 switches, SFPs and optical wires are orderable 8GBit/s FC Controller 8GBit/s FC Controller (for details see price liste) Qlogic Qlogic QLE2560, low profile bracket QLE2562, low profile bracket 1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller LC Interface for 50µm Fiber LC Interface for 50µm Fiber PCIe x8, 170mm PCIe x8, 170mm max. 4x per system max. 4x per system S26361-F3961-E201 S26361-F3961-E202 8GBit/s FC Controller 8GBit/s FC Controller Emulex Emulex LPe1250, low profile bracket LPe12002, low profile bracket 1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller LC Interface for 50µm Fiber LC Interface for 50µm Fiber PCIe x4, 170mm PCIe x4, 170mm max. 4x per system max. 4x per system Loose Component: S26361-F3631-L201 Loose Component: S26361-F3631-L202 Loose Component: S26361-F3961-L201 Loose Component: S26361-F3961-L202 M Fujitsu Technology Solutions x86 PRIMERGY Serve 23 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 M SAS RAID controller for JBOD subsystems as soon as available S26361-F3593-E201 S26361-F3713-E201 8 port SAS RAID Controller RAID Ctrl SAS 6G 8port external LSI LSI MegaRAID SAS 9285-8e MegaRAID SAS9280-8e 6Gb/s 1GB Cache with ECC 512MB Cache with ECC RAID 0, 1, 5, 6, 10, 50 & 60 RAID 0, 1, 10, 5, 50, 6 & 60 without FBU without iBBU SAS 6Gb/sec SAS 6Gb/sec 8 port external 8 port external PCIe x8, MD2 form factor PCIe x4, 167mm low profile bracket max. 1x per system low profile bracket max. 1x per system S26361-F3257-E216 BBU max. 2x per system possible Cache Battery Backup Unit for loose delivery please order S26361-F3257-L210 with 16cm cable set max. 1x per Controller S26361-F3669-E125 Flash Backup Unit with 25cm cable set Lose delivery FBU option max. 1x per Controller as soon as available S26361-F3669-L110 Flash Backup Unit with 25, 55, 70 cable set max. 1x per Controller N Fujitsu Technology Solutions x86 PRIMERGY Serve 24 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 N Section VIII Communication / Network Modular On-Board LAN is a flexible extension of a cost-optimized Motherboard with basic 2x Gbit LAN on-board. 3 different Upgrade-Kits are offered, which consume a dedicated PCIe slot and can be ordered once per system. Every Upgrade-Kit is supported with special TP reduction 2x Gigabit (Dualport) Ethernet Contr. onboard Intel LAN I350 (Powerville) ext: 2x RJ 45 connector NEW) Modular On-Board LAN Adapter S26361-F3610-E702 Upgrade-Kit to 4x Gbit LAN on-board Eth Ctrl 2x1Gbit PCIe x4 D2735-2 Cu Intel Kawela based 2 port Server Adapter S26361-F3611-E701 Upgrade-Kit to 6x Gbit LAN on-board Eth Ctrl 4x1Gbit PCIe x4 D2745 Cu Intel Barton Hills based 4 Port Server Ad. PCIe x4, low profile ext: for RJ45-plug, Cat 5 max. 1x per system PCIe x4, Low Profile ext: for RJ45-plug, Cat 5 max. 1x per system The 10Gb upgrade kit is delivered without SFP+ modules for optical cables, these must be ordered separately. Without SFP+ modules copper twinax cables are supported. The SFP+ Module is also available as loose delivery S26361-F3986-L3 Instead SFP+ Modules, SFP+ twinax cables from S26361-F3629-E702 Upgrade-Kit to 2xGbit+2x10Gbit LAN on-board Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ Intel Niantic based dual port 10Gb NIC PCIe x8, Low Profile, Low Profile Bracket ext: 2x SFP+ cage max. 1x per system S26361-F3986-E3 SFP+ Module MMF 10GbE LC SFP+ module for 10 Gbit Ethernet FO cabling ext:LC-connector max. 2x per adapter the switch vendors may be used S26361-F3629-E750 This is an option if Shared Management LAN over the 10Gb port is required instead Management LAN over 1Gb Shared 10Gb Management LAN Install and configure Management LAN on 10Gb Shared LAN port max. 1x per 10Gb upgrade kit A) 1-Port Copper PCIe Adapter 1000TX S26361-F3516-E201 (Shelter Island) Gigabit Ethernet Controller 1000TX LP Eth Ctrl 1x1Gbit PCI-e Gigabit CT DT Cu LP Intel® Gigabit CT Desktop Adapter PCIe x1 ext: for RJ45-connector, Cat 5 max. 4x per system Loose delivery with: S26361-F3516-L201 B) 1-Port MMF PCIe Adapter 1000SX S26361-F3242-E201 (Sheepshead Bay) Gigabit Ethernet Contr. 1000SX Eth Ctrl 1x1Gbit PCI-e Pro/1000PF LC Intel PRO/1000 PF Server Adapter PCIe x4 ext:LC-connector max. 4x per system C) 2-Port Copper PCIe Adapter 1000TX 4x S26361-F3610-E202 (D2735-2) Gigabit Ethernet Controller Dual 1000TX LP Eth Ctrl 2x1Gbit PCIe x4 D2735-2 Cu Intel Kawela based 2 port Server Adapter PCIe x4, Low Profile ext: for RJ45-plug, Cat 5 max. 3x per system Loose delivery with: S26361-F3610-L502 D) 4-Port Copper PCIe Adapter 1000TX S26361-F3611-E201 (D2745) Gigabit Ethernet Controller Quad 1000TX LP Eth Ctrl 4x1Gbit PCIe x4 D2745 Cu Intel Barton Hills based 4 Port Server Ad. PCIe x4, low profile ext: for RJ45-plug, Cat 5 max. 3x per system Loose delivery with: S26361-F3611-L501 E) 10GbE 2-Port SFP+ for MMF Module S26361-F3629-E202 (D2755) 10 Gigabit Ethernet Contr. dual port SFP+ Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ Intel Niantic based dual port 10Gb NIC PCIe x8, Low Profile, Low Profile Bracket ext: 2x SFP+ cage max. 2x per system S26361-F3986-E3 SFP+ Module MMF 10GbE LC SFP+ module for 10 Gbit Ethernet FO cabling ext:LC-connector The controller is delivered without SFP+ modules for optical cables, these must be ordered separately. Without SFP+ modules copper twinax cables are supported. The adapter is also available as loose delivery with FH and LP bracket included: S26361-F3629-L502 The SFP+ Module is also available as loose delivery S26361-F3986-L3 Instead SFP+ Modules, SFP+ twinax cables from the switch vendors may be used max. 2x per adapter O Fujitsu Technology Solutions x86 PRIMERGY Serve 25 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 O F) Fibre Channel over Ethernet Loose Delivery: S26361-F3592-L202 S26361-F3592-E202 10GBit/s CNA Emulex OCe10102 2 channel 10GBit/sec CNA SFP+ Cage PCIe x8, 170mm max. 2 per system All controllers for the connection of external storage systems are delivered without cables. For the configuration of external cabling see the configurator for external storage systems. S26361-F3592-E108 SFP+ Module MMF 10GbE LC SFP+ module for 10 Gbit Ethernet FO cabling ext:LC-connector The SFP+ Module is also available as loose delivery S26361-F3592-L108 Instead SFP+ Modules, SFP+ twinax cables from the switch vendors may be used max. 2x per adapter G) Infiniband HCA's S26361-F4475-E102 IB HCA 40Gb 1 port QDR IB HCA 1x 40Gb loose delivery: S26361-F4475-L102 Low Profile PCIe form factor with exchangeable Full Height (FH) or Low Profile (LP) bracket PCIe 2.0 (5,0GT/s) PCIe x8, low profile ext: 1x QSFP-connector max. 2x per system 2x S26361-F3996-E500 InfiniBand Cu Cable 40Gb QSFP, customized length max. 1x per adapter S26361-F4475-E202 IB HCA 40Gb 2 port QDR IB HCA 2x 40Gb If additional length of copper cable or optical cable are needed, then they must be ordered from the cable vendor directly Copper cable are also available for loose delivery as S26361-F3996-L101, QSFP, 40Gb, 1m S26361-F3996-L103, QSFP, 40Gb, 3m loose delivery: S26361-F4475-L202 Low Profile PCIe form factor with exchangeable Full Height (FH) or Low Profile (LP) bracket PCIe 2.0 (5,0GT/s) PCIe x8, low profile ext: 2x QSFP-connector max. 2x per system S26361-F3996-E500 InfiniBand Cu Cable 40Gb QSFP, customized length max. 1x per adapter S26361-F4533-E102/E202 IB HCA 56Gb 1 and 2 port FDR IB HCA 2x 56Gb PCIe 3.0 (5,0GT/s) PCIe x16, low profile ext: 2x QSFP-connector max. 1x per system If additional length of copper cable or optical cable are needed, then they must be ordered from the cable vendor directly Copper cable are also available for loose delivery as S26361-F3996-L101, QSFP, 40Gb, 1m S26361-F3996-L103, QSFP, 40Gb, 3m loose delivery: S26361-F4533-L102/202 Low Profile PCIe form factor with exchangeable Full Height (FH) or Low Profile (LP) bracket No mix and match of different IB HCA 40Gb and 56Gb possible. 1x S26361-F3996-E556 InfiniBand Cu Cable 56Gb customized QSFP, 1m and 3m max. 2x per adapter If additional length of copper cable or optical cable are needed, then they must be ordered from the cable vendor directly Copper cable are also available for loose delivery as S26361-F3996-L561, QSFP, 56Gb, 1m S26361-F3996-L563, QSFP, 56Gb, 3m P Fujitsu Technology Solutions x86 PRIMERGY Serve 26 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 P Section IX System Management Products (RemoteView) iRMC S3 (integrated Remote Management Controller) onboard server management Controller with dedicated 10/100/1000 Service LAN-port and integrated graphics. Optional 10/100 Service LAN-port on front panel. The Service LAN-port can be switched alternatively on standard Gbit LAN port S26361-F1790-E242 iRMC S3 advanced pack integrated remote management controller activation key for graphical console redirection and remote media redirection max. 1x per system S26361-F2557-E106 Local Service Display incl. mount. kit Customer Self Service LSD module incl. mounting kit 0.5" x 5.25" max. 1x per system S26361-F2571-E27 Maintenance LAN Front management LAN Port In combination with iRMC adv. pack For local maintenance / console redirection, Integrated in front (operating panel) max. 1x per system Section X Miscellaneous Options and other peripherals For other options, refer to SystemArchitect and Pricelist These options are supplied lose with the shipment For suitable peripherals for this product, please refer to SystemArcitect Section XI Country specific power cord S26361-F1452-E100 S26361-F1452-E110 REGION KIT EMEA AP For Shipments to EMEA / Asia and Pacific regions 1x per system REGION KIT JP For Shipments to Japan regions 1x per system Power cord has to be ordered separately Power cord options (1x per PSU) max. 2x T26139-Y1968-E100 Powercord for rack, 4m, grey, IEC 320 C14 connector T26139-Y1742-E10 USA, Canada, 1.8m, grey T26139-Y4024-E10 for -48V DC PSU only, 4m, black T26139-Y3850-E10 Option "no powercord", for Countries without specific cable orderable like e.g. China End PRIMERGY RX300 S7 Fujitsu Technology Solutions x86 PRIMERGY Serve 27 of 28 System configurator and order-information guide PRIMERGY RX300 S7 Status 2012-05-30 Change Report Date Order number Changes 2012-04-23 2012-04-20 2012-02-29 S26361-F3713-E201 new RAID Controller added Memory voltage / frequency spreadsheet, 3DPC at 1.5V only First Release Fujitsu Technology Solutions x86 PRIMERGY Serve 28 of 28