Download Quickie® Enhanced Display

Enhanced Display
Quickie® Enhanced Display
QR-ED
Owner ’s Manual
Improving People’s Lives
Q R- E D
TA B L E O F C O N T E N T S
I.
II.
III.
IV.
V.
VI.
VII.
INTRODUCTION ..................................................
DRIVE DISPLAY ...................................................
DRIVER MENU .....................................................
MAIN MENU ........................................................
USER ACCESS LEVELS ........................................
TIMED FUNCTIONS ............................................
INFRARED (IR) FUNCTIONS...............................
A. DESCRIPTION .......................................................
B. USAGE ...................................................................
C. IR AV SETUP ...........................................................
1. Enter Setup Code .............................................
2. Train Function ....................................................
D. IR AV CONTROL ...................................................
E. IR ECU SETUP .......................................................
IR Mouse Configuration Setup ...............................
F. IR ECU CONTROL ...............................................
1. Mouse Screen ...................................................
2. X10 ...................................................................
3. Telephone...........................................................
-Answer .............................................................
-Speed Dial ........................................................
-Dial ...................................................................
4. Gewa .................................................................
5. Lights .................................................................
6. Blinds .................................................................
7. Curtains .............................................................
G. OTHER REMOTE-LOCATION
CONTROL OPTIONS............................................
1. X10 wire transition to a remote location .........
2. Infrared (IR) to Radio Frequency (RF) to
Infrared (IR) transmission...................................
3. Infrared (IR) to Radio Frequency (RF) to
Infrared (IR) to X-10 transmission .....................
VIII. FAULTS MENU .....................................................
IX. OPERATE MENU ...................................................
A. DESCRIPTION .......................................................
B. DRIVER MENU ......................................................
C. POWERED SEATING ............................................
D. IR CONTROL ........................................................
E. DRIVE PROFILES ...................................................
F. ECM .......................................................................
G. MISC. MENUS .......................................................
X. MONITOR MENU .................................................
A. MOTOR CONTROLLER .......................................
B. SYSTEM AND J/S 3-BUTTON ..............................
C. SCIM 1 ....................................................................
D. QMAC ....................................................................
E. ECM1 .....................................................................
F. ENHANCED DISPLAY ..........................................
XI. INFORMATION MENU ........................................
XII. PRIMARY PROGRAMMING MENU .....................
A. MOTOR CONTROLLER .......................................
B. QMAC & ENHANCED DISPLAY ..........................
XIII. ADVANCED PROGRAMMING MENU .................
A. MOTOR CONTROLLER ........................................
1. General .............................................................
2. Drive Profile ......................................................
3. System & Actuators ..........................................
B. SCIM 1 ....................................................................
C. QMAC ....................................................................
D. ECM 1 ....................................................................
E. ENHANCED DISPLAY ..........................................
XIV. MAINTENANCE AND CARE ..............................
XV. WARRANTY INFORMATION ..............................
2
4
6
7
8
8
9
9
9
9
9
11
13
14
15
16
16
17
20
20
20
21
22
23
24
25
26
26
26
27
28
28
28
29
30
31
32
33
34
34
35
36
37
38
39
40
41
41
42
43
43
43
44
45
46
47
48
49
50
50
26
I . I N T RO D U C T I O N
Alterations to the power chair and powered seating programming
should only be done with careful consideration by a trained professional. Ensure with your supplier that you can safely operate the
vehicle in all situations.
I. INTRODUCTION
Welcome to the Quickie Enhanced Display control system. Before
delving into the features of this exciting new product, please take a
moment to brief yourself with the following safety considerations.
QUICKIE ENHANCED DISPLAY
WARNING
The QR-ED or Quickie Enhanced Display provides a dashboard
view of the driving and non-driving status of your power chair. It is
an important device that is critical to safe driving and control of
powered seating systems as well as the option of controlling many
elements in your environment. This manual is intended to assist
with the understanding these important new features.
Please ensure that the cabling on your power chair
remains secure. Loose cabling can become caught
and cause damage or injury.
The display is intended to provide the driver with important information about the status of the power chair. Please make sure that
you can read clearly the display at all times.
If the display becomes damaged due to dropping or hitting an
object while driving, please check with your wheelchair supplier to
ensure proper function.
101519 Rev. A
NOTE:
2
If at any point in time while reviewing this manual
you become lost or stuck in a screen, either hit the
mode button (see button location on the next
page) or turn the chair off and start over.
Q R- E D
I.
TERMINOLOGY FOR OPERATING
YOUR SYSTEM
NOTE:
NOTE:
NOTE:
3 MAIN MENUS
There are three primary screens in the Quickie Enhanced Display:
The Drive display screen, the Driver Menu screen, and the Main
Menu screen. The majority of operations are accessible through the
first two. Movement between these menu screens is described
below.
The instructions throughout this manual refer to a “mode button” and a “toggle direction”. All systems will have either a
joystick or a specialized input device, such as proportional
head control, Sip & Puff control, etc, that is used to drive the
power chair. On a joystick (as shown below) there is a Mode
button located on the device. In the case of a specialized system, the mode button may be a switch plugged into the
Quickie Specialty Control Input Module (QR-SCM). If your system does not have another switch, you may be using time to
go from driving to non-driving functions. Please review this
with your supplier to understand your set-up. Throughout this
manual all “mode button” commands are equivalent, meaning the button on the joystick functions just like a button
plugged into the QR-SCM and just like using time.
Detailed descriptions of each screen are in the following pages.
Drive Display
This is the ready-to-drive screen. When
in this screen, inputs to your driver control will move the chair.
To move to the Driver Menu, press
the mode button or if a timed function,
wait the programmed number of
seconds to move to Driver Menu.
As you are using your driving system to navigate through
menus, a “toggle direction” command is equivalent to a
“directional input command”. Please contact the chair’s supplier or technician if there is any confusion concerning how to
operate a specialized input system.
If chair operation is through a
specialized control device, the
drive icon in the top left corner of
the menu screen will be different
from the handcontrol icon in the
menu illustrations at right.
(See specialized icons listed on
page 5.)
Purpose: The Drive Display features realtime
feedback on the chair’s performance.
It helps users more easily gauge the
chair’s operation.
Drive 4
Driver Menu
This screen is a short cut list of all the
functions you are most likely to use. To
return to the Driving Display, press
mode button or give a quick left command. If timed, wait the programmed
number of seconds.
Bat
00000 mi
0.0 mi
To enter the Main Menu, toggle left and
hold for 5 seconds. This opens the
Operate Menu. Left toggle again to the
Main Menu.
Purpose: The Driver Menu provides a list of
short-cuts to commonly used menu
items. The Driver Menu eliminates
time consuming navigation required
to locate these items in the electronic menu tree.
Mode Button
Main Menu
Press mode button to return to the
Drive Display.
Toggle Up
Toggle Left
Purpose: The Main Menu is the starting point
of the electronic menu tree. This
tree contains all the available electronic parameters accessible through
the Enhanced Display.
Drive 4
Bat
00000 mi
0.0 mi
Drive Display
+ +
1 2
3 4
Operate
Driver Menu
Horn
IR Control
Satellite
GEWA
All Lights On
All Lights Off
Driver Menu
1 2
3 4
Main Menu
Operate
Monitor
Information
Faults
Toggle Right
Main Menu
Toggle Down
3
101519 Rev. A
Q R- E D
I I . D R I V E D I S P L AY
II. DRIVE DISPLAY
To best understand the Quickie Enhanced Display, please read the
following pages describing the primary menu screens.
When the Quickie Enhanced Display is turned on, the first menu
screen that appears is the drive display menu. The drive display
menu features all the tools necessary to safely drive the chair.
Common features found on the drive display include:
A
B
A. Drive Profile #:
Indicates the current drive profile (4 total). Each profile provides a
different type of driving experience. For example, one profile might
be set for slow speeds and gradual acceleration, ideal for confined
conditions. Another profile might be set for greater acceleration
and maximum speeds, ideal for driving in more wide open spaces.
Each profile features its own drive input device.
C
H
G
D
F
B. Drive Input Device:
Indicates the type of input device used to drive the chair in that profile.
3, 4 & 5 Button Hand Controls
E
2 Button Hand Control (Compact Joystick)
Front of Enhanced Display (featuring the Drive Display Menu)
Attendant Control Joystick
Specialized Input Devices listed on page 5.
C. Speedometer:
Provides a visual representation of the current speed relative to the
maximum available speed.
D. Odometer:
Records the total number miles driven since QR-ED was built.
I
E. Power Switch:
Turns on and off both the Enhanced Display and the power chair.
J
F. Trip Odometer:
Records the total number of miles since either last charge or last
trip reset.
G. Battery Level Indicator:
Indicates the current battery’s state of charge. (See charge levels
on page 6.)
H. Speed Tick Mark:
Indicates the maximum speed available as set by either the potentiometer dial located in back of the handcontrol or programmed in
that profile. (Note: not all handcontrols have a potentiometer or
speed pot.) As the dial is turned or forward speed is reprogrammed,
i.e. the indicator’s position changes. The speed tick mark will also
change position when the chair is in “creep” mode.
Back of Enhanced Display
I. IR Transmitter/Receiver:
Transmits and receives Infrared signals used to control audio/visual
devices and environmental control devices, such as lights and appliances.
J. Serial Number of the Quickie Enhanced Display.
101519 Rev. A
4
Q R- E D
II.
DISPLAY ICONS
Chairs with specialized input devices and powered seating systems,
such as power lift, power tilt, power recline, power elevating
legrests, feature a slightly different set of screen icons:
Specialized
Control Icon
Specialty Input Devices
Drive 1
Power Seat
Actuator Icon
4-Directional Proportional – provides proportional
command with all 4 directions available (e.g. chin
control, mini joystick)
Bat
00000 mi
3-Directional Proportional – provides proportional
control with 3 directions available (e.g. proportional head control)
4-Switch Discrete – Provides non-proportional
control with 4 directions available (e.g. star or
wafer board)
0.0 mi
Power Seating Systems
Tilt actuator activated.
3-Switch Discrete – Provides non-proportional
control with 3 directions available (e.g. proximity
Head Array)
Recline actuator activated.
2-Switch Discrete – Provides a scheme in which all
4 directions of driving are available with just 2 nonproportional switches.
Lift actuator activated.
1-Switch Discrete– Provides directional movement
in 4 discrete directions. Usually a scanner scrolls
between 4 directions.
Right legrest actuator activated.
1-Switch Discrete– Provides directional movement
in 8 discrete directions. Usually a scanner scrolls
between 8 different directions.
Left legrest actuator activated.
Sip and Puff 4-Pressure Discrete– Uses a sip & puff
to provide directional movement in 4 discrete
directions using 4 different commands.
Dual legrest actuators activated.
Sip and Puff 2-Pressure Discrete– Uses a sip & puff
to provide directional movement in 4 discrete
directions using 2 commands.
Sip and Puff with 2-Switch Discrete– Uses a sip &
puff to provide movement in forward and reverse
with 2 switches to provide left and right turning.
5
101519 Rev. A
Q R- E D
II.
Other icons which may appear are as follows:
The charging icon appears when the chair
is charging.
Drive 3
The Sip & Puff pressure gauge icon is used to provide a visual representation of pressures while
using Sip & Puff driving. The bar graph represents
current pressure. The far left pointer represents a
hard sip trigger point. The far right pointer represents a hard puff trigger point. The inner pointers
represent soft sip and soft puff trigger points.
Bat
00000 mi
0.0 mi
The State-of-Charge (SOC) battery indicator key:
Bat
Battery State Of
Charge
BSOC ≥ 80%
80% > BSOC ≥ 70%
70% > BSOC ≥ 60%
60% > BSOC ≥ 50%
50% > BSOC ≥ 40%
40% > BSOC ≥ 30%
30% > BSOC ≥ 20%
BSOC < 20%
Bar Graph state (left to
right)
7 Black
6 Black
5 Black
4 Black
3 Black
2 Black
1Black
1 Black - Flashing
(1.5 Hz ± 10%, 50% duty
cycle)
III. DRIVER MENU
III. DRIVER MENU
+ +
1
Operate
Driver Menu
This patent pending concept from Quickie allows you to access any
menu item through a single menu. These menu items act as shortcuts to save time and easily alternate between driving and the most
pertinent non-driving activities.
Horn
IR Control
To access the Driver Menu immediately see instructions listed on
page 3.
NOTE: Items listed may
differ, but “IR Control” should
be listed. If it is not, please
contact Customer Support
@ 1-800-456-8166.
The Driver Menu displays the most common non-driving related
menu items (or functions). When leaving the factory, the Driver
Menu contains a selection of menu items (varies depending on chair
configuration) (#1). Once the supplier receives the chair, these and
other menu items can be added or deleted by the supplier using the
Quickie PC Set Up Station (PCSS) available Fall 2006. Number 2 is
an example of a Driver Menu that was modified by a supplier. To
create a custom Driver Menu, please contact the chair’s supplier.
+ +
Operate
Driver Menu
Horn
IR Control
Satellite
GEWA
All Lights On
All Lights Off
101519 Rev. A
1 2
3 4
6
1 2
3 4
2
Q R- E D
I V. M A I N M E N U
IV. MAIN MENU
If the necessary menu item (or function) is not located in the
Driver Menu, it may be located in the Main menu tree (Fig 3). The
Main Menu is the top menu in an expansive menu tree (Fig. 4) that
includes all the functions and adjustable parameters found on the
chair. To access the menu tree, follow the steps on page 3. To
move down in the menu tree, toggle right. To move up in the menu
tree, toggle left. In most cases, menu levels are indicated by the
“+” signs at the top of the screen. Up and down toggle commands
scroll through the items listed on each individual menu screen.
Toggle Up
Toggle up (or up command) to move up in a
menu screen.
3
1 2
3 4
Main Menu
Program
Operate
Monitor
Information
Faults
Toggle Down
Toggle down (or down
command) to move down
in a menu screen.
4
Main Menu
Toggle Left
Toggle left (or left
command) to move up in
the menu tree.
+
+
1 st l000e vel
sub-menu
+
1st level
sub-menu
+
1st level
sub-menu
1st level
sub-menu
Toggle Right
+
+
2nd level
sub-menu
Toggle right (or right
command) to move down
in the menu tree.
+ + +
IR Control
IR Setup
IR AV Setup
IR ECU Setup
7
+
+
+
+
+
+
2nd level
sub-menu
2nd level
sub-menu
2nd level
sub-menu
1 2
3 4
+
+
+
+
3rd level
sub-menu
+
+
3rd level
sub-menu
Level in the menu tree is
indicated by plus “+” signs
at the top of the screen.
101519 Rev. A
Q R- E D
V. U S E R A C C E S S L E V E LS
V. USER ACCESS LEVELS
1 2
3 4
1
1 2
3 4
Main Menu
There are 5 different user access levels in the Quickie Enhanced
Display. For this reason, the main menu may appear different from
user to user. User access-levels are as follows:
Main Menu
Driver Menu
Faults
Level 1 (Fig. 1) allows users to access the Driver Menu and fault
codes.
2
Operate
Faults
Level 2 (Fig. 2) allows users to operate power seat options (power
tilt, power recline, power lift, etc.) as well as specialized control
systems (sip & puff, switch driving, proportional head control, etc.).
Level 3 (Fig. 3) includes level 2 access and adds the ability to monitor critical chair functions and access manufacturing information on
each power module connected to the chair. All chairs ship from the
factory preset to level 3.
1 2
3 4
3
1 2
3 4
Main Menu
Level 4 (Fig. 4) includes level 3 access and adds the ability to
program many basic chair functions.
Level 5 (Fig. 4) includes level 4 access and adds the ability to
program more advanced chair functions.
Operate
Monitor
Information
Faults
This manual covers topics relevant to Level 1 first and progresses
on to higher levels of access. If the Main Menu does not appear,
there is a chance its access has been has been restricted by the
supplier. Please check with your supplier if this is the case or call
customer support @ 1-800-456-8166.
4
Main Menu
Program
Operate
Monitor
Information
Faults
V I . T I M E D F U N C T I ON S
VI. TIMED FUNCTIONS
In cases where accessing a button or switch for the mode command is not desired, then time can be used to navigate between
driving and non-driving functions. This time limit is programmed by
the supplier and can range between 1 and 60 seconds. If no input is
given to the system within the programmed time limit, then it will
change screens from the Drive Display to the Driver Menu. Once
in the Driver Menu, the chair will not drive. To return to driving,
wait the programmed number of seconds or give the system a
quick left command.
SUSPEND
ACTIVATED
Additionally, there are features that will put the chair to sleep. This
is helpful in cases where it is not convenient to turn power off, but
you do not want to accidentally drive.
This sleep mode is indicated by the screen shown at right,
“Suspend Activated”. Usually a long mode command will send the
chair to sleep and wake it up again.
101519 Rev. A
8
Q R- E D
VII. INFRARED (IR) FUNCTIONS
C. IR AV SETUP
VII. INFRARED (IR) FUNCTIONS
1. Enter Setup Code
Follow these screen menu instructions to set up any one or all of
the following AV devices: TVs, cable boxes, stereos, satellite control systems, VCRs, TiVo boxes, DVD players, radio receivers, and
CD players .
(Accessible to all user levels)
A. DESCRIPTION
The Quickie Enhanced Display is also designed to function as a universal remote control unit by emitting InfraRed (or IR) command
signals to infrared receptive devices, such as TVs, stereos, DVD
players etc. It is also capable of sending infrared signals to environmental control modules that operate electrical devices throughout
the house.
Press
Mode
Button
Bat
00000 mi
Both AV and ECU devices are grouped into their own set-up
menus (which configure the devices for use) and operate menus
(which provide a means of actually controlling each device).
Because none of these devices function until they are set up, setup
instructions precede operation instructions.
+ +
In most cases, Quickie Enhanced Display screen-menus appear
identical to the screen-menu illustrations on the following pages.
However, the number of “+” signs at the top may vary by one and
the number of listed devices may also vary depending on factory or
dealer setup preferences.
3
1 2
3 4
Operate
IR Control
Toggle
Down to
IR Setup
then
toggle
right
IR AV Control
IR ECU Control
IR Setup
The IR or infrared functions on the Quickie Enhanced Display work
by broadcasting infrared light signals to an IR receiver. For IR to
work, you must maintain line-of-sight with the device you want to
control. Because of this, it is important that the IR
transmitter/receiver (Fig. 1-A) on the back of the Enhanced Display
is pointed at the IR receiver on the AV or ECU device. The beam
emitted from the IR transmitter/receiver spreads out at a 15
degree angle and has strong reception at distances up to 20 feet
(see Fig 2). Reception may or may not work at angles greater than
15 degrees or distances greater than 20 feet. Much depends on the
reflective surfaces in the area and the type of lighting. Strong florescent lighting or sunlight, for instance, can sometimes impede IR signals. If the intended IR receiver is not picking up the signal, try
changing angle and distance. Sometimes if the distance is too close,
the beam misses the target. If the signal is too far away, it may not
generate sufficient strength to overcome competing light sources.
A
1 2
3 4
+ + + +
Toggle
Down to
IR Control
Horn
then
IR Control
Toggle
NOTE: Items listed may Right
differ, but “IR Control” should
be listed. If it is not, please
contact Customer Support
@ 1-800-456-8166.
0.0 mi
B. USAGE
1
2
+ +
Operate
Driver Menu
Devices such as TVs, cable boxes, stereos, satellite control systems,
VCRs, TiVo boxes, DVD players, radio receivers, and CD players
are referred to as Audio Visual or “AV” devices. Environmental
controls, such as remote computer-mouse operation, X10 control
systems, IR telephones, Gewa controls, Lutron lights, Hunter
Douglas Blinds, and Makita Curtains are referred to as
Environmental Control Units or “ECU” devices.
NOTE:
1
Drive 4
+ + +
4
1 2
3 4
IR Control
IR Setup
IR AV Setup
IR ECU Setup
Toggle
Right
5
1 2
3 4
IR Setup
IR AV Setup
Repeat Time
TV
Cable
Satellite
VCR
TIVO
Toggle down to
the device
you
2s
wish to set up.
This example
uses a TV.
2
Once in the “IR Setup/IR AV Setup” menu (#6- next page) toggle
down to enable the device of your choice. Enable the item by highlighting the device and toggling right. You will also see “Repeat
Time”. This should only be changed if you encounter issues transmitting a command. It will change how quickly the signal is repeated.
max. range
20’
15˚
max.
angle
9
101519 Rev. A
Q R- E D
VII.
C.
(The example setup below is for a Television set.
Setups for other AV devices are identical.)
The “Yes” (#8) Enable command activates a device for use in the IR AV Control menu.
To disable remote operation at any time, return Enable to “No”.
+ + + +
6
1 2
3 4
IR Setup
IR AV Setup
Repeat Time
TV
Cable
Satellite
VCR
TIVO
7
+ + + + +
+ + + + +
1 2
3 4
IR AV Setup
TV
Toggle
2s
Right
8
1 2
3 4
IR AV Setup
TV
Enable
TV Setup
TV Train
Enable
TV Setup
TV Train
No
Toggle
Right
Yes
Toggle
Down
Once a device is enabled, set up the Quickie Enhanced Display for the brand of AV device
by using a 4-digit setup code (#10). (See Manufacturer Setup Code Appendix A to find
each manufacturer’s 4-digit setup code.) If a device setup code (or group of device setup
codes) is found for the device, enter the first 4-digit code in the device setup menu (#10)
as shown below. If more than one code exists for the device, it may be necessary to test
the operation for each code (see IR AV Control on page 3). If none of the codes work,
contact Customer Support @ 1-800-456-8166.
+ + + + +
9
1 2
3 4
IR AV Setup
Toggle right
TV
Enable
TV Setup
TV Train
101519 Rev. A
and follow
menu
Yes
instructions.
“Escape” is
the mode
button.
Press when
done.
10
+ + + + +
IR AV Setup
TV
TV Setup
4
0
9
5
Adjust the code using the
following commands
Forward – Increment digit
Reverse – Decrement digit
Right – Move to the next digit
Left – Move to previous digit
Escape – When done.
10
+ + + + +
Press
Mode
button
Enable
TV Setup
TV Train
11
1 2
3 4
Press
Mode
Yes
button
when
finished
Q R- E D
VII.
C.
2. Train Function
If the IR setup codes do not work (after going through IR AV Control – page 13) or the
device does not have a code, the Quickie Enhanced Display can still be “trained” to operate the device. Training essentially programs the Quickie Enhanced Display to mimic the IR
transmitter codes that are sent out by the device’s remote. (See photograph on the next
page.) Most audio-visual devices with IR capability ship with a hand held IR remote control.
1
Drive 4
2
+ +
+ +
1 2
3 4
Operate
Driver Menu
Press
Mode
Button
Bat
00000 mi
4
1 2
3 4
IR Control
IR Setup
IR AV Setup
IR ECU Setup
+ + + + +
+ + + +
IR Setup
IR AV Setup
Toggle
Right
7
1 2
3 4
IR AV Setup
TV
Enable
TV Setup
TV Train
Operate
IR Control
IR AV Control
IR ECU Control
IR Setup
Toggle
down to
IR Setup
then
toggle
right
be listed. If it is not, please
contact Customer Support
@ 1-800-456-8166.
0.0 mi
+ + +
Toggle
down to
Horn
IR Control
IR Control
then
toggle
NOTE: Items listed may
differ, but “IR Control” should right
3
1 2
3 4
Repeat Time
TV
Cable
Satellite
VCR
TIVO
+ + + + +
5
+ + + +
1 2
3 4
IR Setup
IR AV Setup
Toggle
Down to
the device
2s wish
you
to set up.
Repeat Time
TV
Cable
Satellite
VCR
TIVO
TV is used
in this
example.
8
+ + + + +
1 2
3 4
TV
TV Train
IR AV Setup
TV
No
Toggle
Right
(Must say
“Yes” or the
device will
not appear
for use.)
Enable
TV Setup
TV Train
6
1 2
3 4
Power
Ch Up
Ch Dn
Vol Up
Vol Dn
Mute
Yes
Toggle
down to
TV Train
then
toggle
right
11
Toggle
2s
Right
9
1 2
3 4
Toggle
down
to the
function.
(“Channel
Up” in this
example)
101519 Rev. A
Q R- E D
VII.
C.
Theory Behind Training the Enhanced Display
Whenever a button on a remote controller is pressed, the controller emits an infrared code
for that button’s function. On the backside of the Quickie Enhanced Display is an IR sensor
that both sends and receives infrared coded signals. Aiming a hand held remote at the backside of the Quickie Enhanced Display and pressing the button for a particular function (such
as “Channel Up”) beams that function’s infrared code into the Quickie Enhanced Display IR
receiver. Using the steps outlined on the next page, this code is logged as the function displayed on the Quickie Enhanced Display “Train” menu (#11). Once logged, any time this
function (“Channel Up” in this example) is selected in the Quickie Enhanced Display user
menu, it automatically broadcasts from the Enhanced Display.
IR receiver/transmitter
Hand held remote
To Program:
a. Toggle right from the highlighted function to open the train menu (#11).
b. Position the hand held remote directly in front of the IR sensor about 8” – 12” from
the backside of the Enhanced Display (see figure above). Make sure the remote control LED (looks like a small flashlight bulb located in front of the hand held remote)
is pointed at the Enhanced Display IR Receiver/Transmitter (see photo).
c. Execute a quick toggle right. The remote icon (#11-B) will start flashing. Immediately
press the function button on the remote control. If the signal was successfully
received, the remote icon will stop flashing and the Enhanced Display icon (#11-A)
will start flashing. If unsuccessful, an “X” will appear over the remote icon. In this
case, toggle left to exit the train screen and then toggle right to re-enter the train
screen. Repeat steps a, b & c.
d. Once the Enhanced Display icon flashes (#11-A) toggle left to exit. An asterisk (*)
(#12) will appear next to the function to indicate that is is now “trained”.
+ + + + +
TV
TV Train
Power
Ch Up
Ch Dn
Vol Up
Vol Dn
Mute
101519 Rev. A
10
1 2
3 4
Toggle
right and
follow
instruction
on screen
or above
11
+ + + + +
Train
Ch Up
A
Toggle left
once
Enhanced
Display
icon (A)
is flashing
B
To program IR follow these steps
1. Position a transmitter as shown
2. Give a RIGHT command.
3. Immediately press REMOTE
BUTTON.
4. Use a LEFT command to exit.
12
+ + + + +
TV
TV Train
Power
Ch Up *
Ch Dn
Vol Up
Vol Dn
Mute
12
1 2
3 4
Press
Mode
button
when
finished
Q R- E D
VII.
D.
D.IR AV CONTROL
Once an IR Audio Visual device has been setup for use, operation is simply a matter of toggling to the appropriate screen menu. Follow the screen-menu illustrations below to locate
the device’s control functions. The roadmap starts from the main drive menu (#1), which
appears when the chair is turned on.
1
Drive 4
2
+ +
Operate
Driver Menu
Press
Mode
Button
0.0 mi
+ + + + +
IR AV Control
TV
TV Mode
TV List
Toggle
down to
IR Control
then
toggle
right
NOTE: Items listed may
differ, but “IR Control” should
be listed. If it is not, please
contact Customer Support
@ 1-800-456-8166.
Bat
00000 mi
Horn
IR Control
1 2
3 4
Driver Menu
IR Menu
IR AV Control
IR ECU Control
IR Setup
TV
TV List
Make sure the
Enhanced Display is
pointed at the device
(TV in this example)
Power
Ch Up
Ch Dn
Vol Up
Vol Dn
Mute
+ + + +
IR Menu
IR AV Control
Toggle
Right
TV
Cable
Satellite
VCR
TIVO
DVD
4
1 2
3 4
Toggle
right or
down to
the device
of choice
then
toggle
right
6
+ + + + -
5
1 2
3 4
Toggle
down to
TV List
then
toggle
right
3
+ + +
1 2
3 4
1 2
3 4
Quick
Toggle
right to
turn on
and quick
toggle
right to
turn off
A device’s “List” (#6-8) always contains the “power on/off” command. The device’s
“Mode” (#5) does in some cases and not in others. This “List” contains all the available
commands for the device. The “Mode” only contains the 4 most common commands,
such as volume, channel, play, stop, etc. To activate any of the list commands, toggle right
as demonstrated in #6.
List commands are named with their appropriate function. The “Open” list commands can
be reprogrammed for additional funcitons (see #8-A) not found on the list. For example,
the TV remote might have a button that switches between TV and Video. If this remote
button-function is not found on the list, “TV Open 1, 2, or 3” can be “trained” to duplicate
this function (see “train” setup on page 11).
+ + + + -
TV
TV List
Power
Ch Up
Ch Dn
Vol Up
Vol Dn
Mute
7
1 2
3 4
Toggle
down to
highlight an
“open”
function
(see
instructions
above)
8
+ + + + -
+ + + + +
1 2
3 4
IR AV Control
TV
TV
TV List
Vol Dn
Mute
Input
TV Open 1
TV Open 2
TV Open 3
TV Mode
TV List
Toggle
left to
exit List
9
1 2
3 4
Toggle
up to
TV Mode
then
toggle
right
A
13
101519 Rev. A
Q R- E D
VII.
D/E.
The mode menu (#11) provides 4 of the most common commands. Toggle in the direction of the screen arrows to activate any of the displayed commands. Press (or activate)
the mode button (or command) to exit the Mode menu when finished (#11). (4-choice
menu screens can only be exited by pressing the mode button (or command).)
10
11
Ch Up
Vol Dn
TV
+ + + + +
Vol Dn
TV Mode
Press
Mode
button to
exit
Press
Mode
button
when
finished
TV Mode
TV List
Vol Up
Ch Dn
13
Drive 4
3 4
IR AV Control
TV
Ch Up
Toggle
in the
direction
Mode of the
screen
Vol Up arrows.
12
1 2
Bat
00000 mi
Ch Dn
0.0 mi
E. IR ECU SETUP
Environmental Control Unit (ECU) devices include: remote computer-mouse operation,
X10 control systems, IR telephones, Gewa controls, Lutron lights, Hunter Douglas Blinds,
and Makita Curtains. Each device can be controlled using infrared signals.
All IR Environmental Control Units require the function be enabled before it appears in the IR
ECU Control menu (#5). Follow the menu illustrations below to locate the device’s (or system’s) control functions. Some additional setups may be required in the IR ECU Control
menu. (This will be covered in the individual function explanations later in this section.) “IR
Mouse Cfg” is covered on the next page of this manual.
1
Drive 4
+ +
2
+ +
1 2
3 4
Operate
Driver Menu
Press
Mode
Button
Bat
00000 mi
+ + + -
+ + +
Operate
IR Control
IR AV Control
IR ECU Control
IR Setup
Toggle
down to
IR Setup
then
toggle
right
IR Control
IR Setup
IR AV Setup
IR ECU Setup
be listed. If it is not, please
contact Customer Support
@ 1-800-456-8166.
0.0 mi
5
1 2
3 4
IR Setup
Toggle
IR ECU Setup down to
any ECU
device you
Mouse Cfg
Enable Mouse Scree wish
No to
enable
Enable X10
No
then
Enable Tele
No
toggle
Enable GEWA
No
right
Enable Lights
No
101519 Rev. A
Toggle
Horn
down to
IR Control
IR Control,
then toggle
NOTE: Items listed may
right
differ, but “IR Control” should
3
1 2
3 4
+ + + -
6
+ + + -
1 2
3 4
IR Setup
IR ECU Setup
Mouse Cfg
Enable Mouse Scree Yes
Enable X10
No
Enable Tele
No
Enable GEWA
No
Enable Lights
No
Continue
to toggle
down and
right to
open all
necessary
ECU
devices.
14
7
1 2
3 4
IR Setup
IR ECU Setup
Mouse Cfg
Enable Mouse Scree Yes
Enable X10
No
Enable Tele
No
Enable GEWA
Yes
Enable Lights
Yes
Press
Mode
button
when
finished
4
1 2
3 4
Toggle
down to
IR ECU
Setup then
toggle
right
Q R- E D
VII.
E.
IR Mouse Configuration Setup
Unlike the other ECU functions, IR Mouse configuration setup is
located in its own section of the IR ECU Setup menu. An IR Mouse
allows you to control the cursor on the computer screen using the
joystick or a specialized input control. Follow the screen menu
illustrations below to access the “Mouse Cfg” menu.
1
Drive 4
2
+ +
+ +
1 2
3 4
Operate
Driver Menu
Toggle
Horn
down to
IR Control
IR Control,
then toggle
NOTE: Items listed may
right
differ, but “IR Control” should
Press
Mode
Button
Bat
00000 mi
5
+ + + + +
1 2
3 4
IR Setup
IR ECU Setup
Mouse Cfg
Enable Mouse Scree
Enable X10
Enable Tele
Enable GEWA
Enable Lights
6
Operate
IR Control
IR AV Control
IR ECU Control
IR Setup
+ + + + -
1 2
3 4
IR ECU Setup
Mouse Cfg
Min Mouse
Mouse Start Time
Mouse Accel
Max Mouse
Mouse Latch Time
Toggle
No
Right
No
No
No
No
+ + + + +
Toggle
down to
IR Setup
then
toggle
right
3
2.0s
5
Toggle
8
Right
2.0s
IR Control
IR Setup
IR AV Setup
IR ECU Setup
+ + + + -
4
1 2
3 4
Toggle
down to
IR ECU
Setup and
then
toggle
right
8
1 2
3 4
Mouse Cfg
Min Mouse
Max
10
Current
5
Min
1
Toggle
up to
increase,
down to
decrease
Units - NA
Max
10
Current
7
Min
1
Units - NA
9
A
1 2
3 4
Program
another
mouse
3
configuration
2.0s
function or
5 Mode
press
button
to
8
2.0sfinish
Min
Mouse
Speed
Max
Mouse
Mouse Speed
Accel
}
fast – (Mouse Speed) – slow
Min Mouse
Mouse Start Time
Mouse Accel
Max Mouse
Mouse Latch Time
7
1 2
3 4
Mouse Cfg
Min Mouse
IR ECU Setup
Mouse Cfg
Toggle
Left
+ + +
be listed. If it is not, please
contact Customer Support
@ 1-800-456-8166.
0.0 mi
+ + + -
3
1 2
3 4
Time in seconds
Mouse
Start Time
Mouse Accel determines the acceleration rate the cursor accelerates from the minimum mouse tracking-speed to the maximum
mouse tracking-speed once the mouse start-time ends.
Each function within the Mouse Cfg menu provides a detailed
adjustment of the IR Mouse operation on the computer screen.
Above is an example of how one of the operation parameters is
modified. For more information on the operation parameters, contact Customer Service @ 1-800-456-8166. Also, see graph “A”
above. The operation parameters (#6) are defined as follows:
Max Mouse sets the maximum mouse tracking speed.
Mouse Latch Time is the amount of time required for a sustained
right or left mouse-button command to engage latch mode. Latch
mode, from a functional standpoint, is the same as continuously
holding your finger down on a computer mouse button. This makes
it easy for individuals with minimal hand control to perform latched
mouse functions, such as highlighting a block of text. When the
same mouse button is engaged again the button is released.
Min Mouse sets the minimum mouse tracking speed across the
screen.
Mouse Start Time determines the amount of time in seconds the
command must be held before the minimum mouse tracking-speed
accelerates to the maximum mouse tracking-speed.
15
101519 Rev. A
Q R- E D
VII.
F.
F. IR ECU CONTROL
Because each IR ECU device functions in its own unique way, a separate section is devoted
to the control operation of each individual ECU device. To navigate to the device-selection
starting point, follow the menu illustration instructions listed below.
1
Drive 4
2
+ +
+ + +
1 2
3 4
Driver Menu
IR Menu
Operate
Driver Menu
Press
Mode
Button
Bat
00000 mi
Toggle
down to
Horn
IR Control
then
IR Control
toggle
NOTE: Items listed may
right
IR AV Control
IR ECU Control
IR Setup
differ, but “IR Control” should
be listed. If it is not, please
contact Customer Support
@ 1-800-456-8166.
0.0 mi
3
+ + + +
1 2
3 4
Toggle
down to
IR ECU
Control
then
toggle
right
1. Mouse Screen
The IR Mouse Screen is designed to work in conjunction with the Remote Point ™
(Interlink Electronics) IR mouse receiver (See IR device list appendix C). This receiver
must be installed and plugged into the computer before the Mouse Screen control functions will work. Please follow all Remote Point instructions when installing.
4
1 2
3 4
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
IR Mouse Receiver
Mouse screen movement operates in 4 directions for discrete (straight line) input devices
and in proportional (380°) for proportional devices. Right and left mouse button control
will vary depending on the input device used (handcontrol, mini-joystick, Sip & Puff,
Proportional head array, etc). Once in the Mouse Screen, move the joystick (or input
device) in the direction of the screen arrows (#2-below). The mouse will move in a similar
proportional or discrete direction. To adjust movement speed, refer to page 15.
The right and left mouse button can be emulated using the bottom left and bottom right
buttons ONLY on a Quickie 7-Button hand controller. If the hand controller is a 2-Button,
3-Button, or specialized input device, you can purchase the following screen software to
provide mouse button control:
Dragger 32
http://www.orin.com/chi-bin/miva?Merchang2/merchant.mv+Screen=PROD&Store_
Code=O&Product_Code=AC-0841-32&Category_Code=B
Dwell
http://www.gusinc.com/dwell.html
Operation instructions are included with both software packages. Software is easily
downloaded from the internet.
+ + + +
1
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
101519 Rev. A
3
2
1 2
3 4
Press lower
left button
on a 7Left
Button
hand conMouse Screentrol to
emulate a
Rightleft mouse
button on a
Down
computer
mouse.
Up
Up
Toggle
Right
Toggle
in the
Left
direction of
the screen
arrows for
Mouse Screen
computer
Right screen
mouse
movement.
Down
16
4
Press lower
right button
on a 7Left
Button
handcontrol
Mouse Screen
to emulate a
right mouse
Rightbutton on a
computer
Down
mouse.
Up
Q R- E D
VII.
F.
If using a 7-Button handcontroller, press the bottom left-hand button to execute a
left mouse click (#3) or the bottom right-hand button to execute a right mouse click
(#4– previous page). Holding either the right or left mouse button down for more than
“X” seconds (determined by the Mouse Latch Time setting; see page 15) latches the
mouse button down. (This is the same as continuously holding a computer mouse button
down with your finger.) When the button is pressed again, the mouse button is released.
This function is helpful in highlighting text or moving (dragging) objects on the screen.
+ + + +
5
1 2
3 4
6
Drive 4
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
Press
Mode
button
when
finished
Bat
00000 mi
0.0 mi
2. X10
X10® devices are used to control home, office, and business environmental systems, such
as lights and appliances. (See IR Device List Appendix C.) Entire households can be set up
with X10 systems so that every light and most appliances can be controlled from the
Quickie Enhanced Display.
Here is how X10 works:
The Quickie Enhanced Display broadcasts an infrared beam to an X10 IR Controller
“Powerhouse”. (The controller must be in the sight line of the Quickie Enhanced Display.)
(Figure A)
The controller converts the infrared signal into a coded electrical pulse that travels through
the house wiring. (Figure B)
When an X10 module or switch receives the coded pulse, it either opens or closes the circuit to the lamp or appliance. (Figure C)
X10 IR Controller
“Powerhouse”
B
A
C
X10 IR
Lamp
Module
17
101519 Rev. A
Q R- E D
VII.
F.
Each X10 IR controller “Powerhouse” is assigned an alphabetical (A-P) “house code”.
Usually, each room in a house has its own X10 controller set to a specific numerical house
code that operates the lights/appliances in that room. To operate, they must be within lineof-sight of the Quickie Enhanced Display. Each Powerhouse controller can add up to 10
new associated modules. All 10 modules must use the same house code. Up to 16 “house
code” letters are available (one for each Powerhouse controller), which means up to 160
modules are available for any given house or building. For this reason, the same “Unit 1”,
“Unit 2”, “Unit 3”, etc. on the Quickie Enhanced Display screen may operate light/appliances in more than one room. If more than 10 modules are required for a given house or
installation, additional controllers and modules must be added.
Controller “house code”
set to “A”.
Setting to a different letter
on another controller provides control of a different
set of Unit #’s 1-10.
X10 Powerhouse
IR Controller
+ + + + +
IR ECU Control
X10
These “unit codes”
correspond to the unit
numbers on the
Enhanced Display.
Module set
to “A”
X10 Module
To operate an X10 device, toggle down and highlight “X-10” in the IR ECU Control list;
then toggle right. (NOTE: The X10 system must be properly set up before using. Refer to
page 17 for setup hints. Consult X10 instructions for full setup details.) A list of available
units is posted on the next page.
(See page 16 to navigate to #1.)
+ + + +
1
1 2
3 4
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
Toggle
down to
X10 then
toggle
right
+ + + + +
2
1 2
3 4
IR ECU Control
X10
Unit 1
Unit 2
Unit 3
Unit 4
Unit 5
Unit 6
Toggle
Right
Toggle right (#2) and then up to turn on the device (#3– next page). Follow screen
arrows for other commands. If the commands do not work, then press the mode button
to go back to the unit screen (#2) and try again. The problem may be that the unit selected did not signal the X10 receiver that it is now in a new unit. Following each IR transmission, a red light will illuminate on the Powerhouse controller.
101519 Rev. A
18
Unit 1
Unit 2
Unit 3
Unit 4
Unit 5
Unit 6
1 2
3 4
Q R- E D
VII.
F.
3
On
To activate
a different
Dim
function,
press the
X10 Unit 1 mode
button to
Bright return to
the Unit
list.
Off
+ + + + +
IR ECU Control
X10
Unit 1
Unit 2
Unit 3
Unit 4
Unit 5
Unit 6
+ + + + +
4
Toggle
down to a
different
unit
Unit 1
Unit 2
Unit 3
Unit 4
Unit 5
Unit 6
7
+ + + + +
1 2
3 4
Right.
Follow the
arrows to
access
other
commands.
IR ECU Control
X10
If there is a need to turn
all lights on or off, toggle
down to either “All Light
On” or “All Lights Off”
command and then right
toggle to activate these
functions.
Unit 7
Unit 8
Unit 9
Unit 10
All Lights On
All Lights Off
6
1 2
3 4
IR ECU Control
X10
Toggle
IR ECU Control
X10
Unit 1
Unit 2
Unit 3
Unit 4
Unit 5
Unit 6
5
+ + + + +
1 2
3 4
8
1 2
3 4
Press
mode
button
when
finished
On
Dim
X10 Unit 3
Press the
mode
button to
exit
Bright
Off
9
Drive 4
Bat
00000 mi
0.0 mi
Control of X10 devices requires an X10 IR controller “Powerhouse” (see previous page)
and any of the following components (see page 18 for photos). These items listed below
are available in most electronics stores. They can also be found on the web at
www.x10.com – click on the automation tab.
• Wall Switch
Wall Switch w/ Dim and 3-Way
Decorator Style Wall Switch
• Wall Switch Module
Wall Switch Module - 3-way
Appliance Module - 2-way, 2-pin
Appliance Module 2-Pin Polarized
Appliance Module 3-Pin Grounded
Heavy Duty 220V 15A Appliance Module
Heavy Duty 220V 20A Appliance Module
• Lamp Module
• Lamp Module - 2-way
• Remote Chime
• Socket Rocket Screw-in Lamp Module
• Universal Module
• Wall Receptacle Module
19
101519 Rev. A
Q R- E D
VII.
F.
3. Telephone– Answer
The telephone function is designed to work in conjunction with the Gewa® Jupiter IR telephone. All the necessary telephone options are already pre-programmed, with the exception of the speed dial functions, to interface with the Gewa Jupiter IR telephone. (See IR
Device Appendix C.) To program the speed dial functions, refer to page 6 of the GEWA
Jupiter phone instruction manual. In addition, the Jupiter phone is designed to work only
with analogue phone lines. To answer an in-coming call, follow the 6 screen menus below.
An IR indicator will
flash red
when IR
signal
commands
are
received.
To test the answer function, dial the Gewa telephone from a phone with a different number. When the Gewa phone rings, right toggle (#2). Once in the 4-selection box (#3), toggle left to answer the phone.
To increase, decrease the volume, or mute the phone, toggle in the direction of the arrow
on the display (#3). Toggle left to hang up. Once the line is disconnected, press the mode
button to return to the telephone menu.
(See page 16 to navigate to #1)
1
+ + + +
1 2
3 4
IR Menu
IR ECU Control
Toggle
down to
Telephone
then
toggle
right
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
2
+ + + + +
3
1 2
3 4
IR ECU Control
Telephone
Answer
Speed Dial
Dial
Volume Up
Ans/Hang (S)
Answer
Toggle
Right
Toggle left
to answer
Mute
Vol Dn
4
Volume Up
+ + + + +
Ans/Hang (S)
Toggle left
again to
hang up
Press
Mode
button
Answer
Mute
Answer
Speed Dial
Dial
Mute
Vol Dn
6
1 2
3 4
IR ECU Control
Telephone
Volume Up
Ans/Hang (S)
Answer
5
Vol Dn
Telephone – Speed Dial
To access the speed dial function, highlight “Speed Dial” and toggle right. See Gewa phone
instructions (page 6) to program memory slots M1-K11.
+ + + + +
1
1 2
3 4
IR ECU Control
Telephone
Answer
Speed Dial
Dial
101519 Rev. A
Highlight
Speed
Dial then
toggle
right
+ + + + -
Telephone
Speed Dial
Dial (S)
M1
M2
M3
M4
M5
2
+ + + + -
1 2
3 4
Telephone
Speed Dial
Toggle
down to
the
desired
speed dial
memory
location
Dial (S)
M1
M2
M3
M4
M5
20
3
1 2
3 4
Toggle
right to
display the
# on the
phone
Speed dial
# will
appear
in the LED
display
Q R- E D
VII.
F.
4
+ + + + -
1 2
3 4
Telephone
Speed Dial
Telephone
Speed Dial
Dial (S)
M1
M2
M3
M4
M5
+ + + + -
Toggle
up to
Dial (S)
Dial (S)
M1
M2
M3
M4
M5
6
+ + + + +
1 2
3 4
Telephone
Speed Dial
Dial (S)
M1
M2
M3
M4
M5
5
+ + + + -
1 2
3 4
Toggle
right to
dial the
number,
which may
take a few
seconds.
Toggle right
to diconnect
once the call
has ended.
7
1 2
3 4
IR ECU Control
Telephone
Toggle left
to return
to the
telephone
menu
Answer
Speed Dial
Dial
Telephone – Dial
To access the dial function from the telephone menu, highlight “Dial” then toggle right (#1).
NOTE:
To enter a phone number, toggle down to the first digit of the number and toggle right to
display it on the phone’s LED screen. The “-” sign indicates a slight pause in dialling, which
is helpful for numbers that require reaching an outside access line first. Once the full phone
number is displayed on the phone LED, highlight “Dial (S)” and then right toggle to dial the
#. Toggle right on “Dial (S)” to disconnect when the call has ended.
+ + + + +
1
1 2
3 4
IR ECU Control
Telephone
Answer
Speed Dial
Dial
+ + + + -
Toggle
down to
Dial then
toggle
right
5
1 2
3 4
Telephone
Dial
Dial (S)
*
#
R
P
Vol Up
Toggle
Left
+ + + + -
Telephone
Dial
Redial
1
2
3
4
+ + + + +
2
3
+ + + + -
1 2
3 4
Toggle
down or
up to any
function or
#, then
toggle right
to enter
the # on
the phone
display.
6
1 2
3 4
1 2
3 4
Telephone
Dial
Dial (S)
*
#
R
P
Vol Up
Toggle
right to
dial the #
once the
complete
phone #
is entered.
The letters “R” and “P” are not
currently active.
+ + + + -
Telephone
Dial
Dial (S)
*
#
R
P
Vol Up
4
1 2
3 4
Toggle
right to
disconnect
when the
call has
ended
7
Drive 4
IR ECU Control
Telephone
Answer
Speed Dial
Dial
Press
Mode
button
when
finished
Bat
00000 mi
21
0.0 mi
101519 Rev. A
Q R- E D
VII.
F.
4. GEWA
Gewa AB, located in Sweden, manufactures a large selection of IR environmental receiving
devices. Unlike X10, which uses a central IR receiver to broadcast electrical pulses to
remote receivers through the house wiring, each Gewa module contains its own IR receiver. Visit http://www.zygo-usa.com/envctrl.htm for a more complete listing of Gewa products. (See IR Device Appendix C.)
IR indicator light
Set
Buttons
To activate a Gewa device, the outgoing IR code must be first “trained” (or programmed)
into the Gewa IR receiver. This process is easier to accomplish with two people. Point the
Quickie Enhanced Display directly at a Gewa receiver (see photo). Push and hold one of
the small set-buttons on the side of the receiver. Broadcast the IR command by quick-toggling right while continuing to maintain pressure on the set-button on the side of the Gewa
receiver. Two clicks should sound signalling that the receiver has been set. Let go of the set
button. Similar instructions are located in the Gewa receiver instruction manual. Make sure
the electrical device (lamp, door opener, etc) is plugged into the Gewa receiver. Right toggle again. If the receiver was properly trained, the device should turn on or off with each
right toggle. The IR indicator light will also blink when an IR signal is received. Please contact customer support if this procedure fails 1-800-456-8166.
Gewa IR Receiver
(See page 16 to navigate to #1)
1
+ + + +
1 2
3 4
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
+ + + + -
4
1 2
3 4
IR ECU Control
GEWA
1
2
3
4
5
6
101519 Rev. A
Toggle
down to
GEWA
then
toggle
right
Toggle
left to exit
or down
to select
another
device
2
+ + + + -
1 2
3 4
IR ECU ControlToggle right
to set the
GEWA
code.
Should hear
the GEWA
receiver
make 2
cicks.
1
2
3
4
5
6
(See instructions above.)
+ + + +
5
3
+ + + + -
1 2
3 4
IR ECU Control
GEWA
Toggle
right to
test on/off
function
1
2
3
4
5
6
6
Drive 4
1 2
3 4
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
Press
Mode
button
when
finished
Bat
00000 mi
22
0.0 mi
Q R- E D
VII.
F.
5. Lights
“Lights” refers to programmable Lutron® Maestro IR multi-location dimmer switch. The
Maestro IR switch is pre-programmed to interface with the “Lights” option on the IR ECU
Control menu. Ensure you are using this designated Lutron equipment or the “Lights”
function will not work. (See IR Device Appendix C.)
NOTE:
Lutron lights may be used only with filament/incandescent lights not florescent lights.
To turn on a light fixture using the Maestro switch, toggle into the “Lights Mode” menu
(#1-3). In this menu, the boxed arrows indicate the toggle direction for each command.
Lutron®
Maestro IR
multi-location
dimmer
switch
(replaces
existing wall
switches)
(See page 16 to navigate to #1)
1
+ + + +
1 2
3 4
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
Toggle
down to
lights then
toggle
right
3
2
+ + + + -
1 2
3 4
IR ECU Control
Lights
Preset/Off
Lights Mode
4
Bright
Toggle
right to
turn on the
Off
lights.
Follow
Lights Mode screen
arrows to
On execute
other
Dim
commands.
Toggle
down to
Lights
Mode
Bright
Off
Lights Mode
On
Press
Mode
button to
exit
Dim
The “Preset/Off” value turns the light off or on to the previous bright or dim value last
established in the “Light Mode” screen (#7).
+ + + + +
IR ECU Control
Lights
Preset/Off
Lights Mode
5
1 2
3 4
+ + + + +
+ + + + -
6
1 2
3 4
IR ECU Control Toggle
right to
Lights
IR ECU Control
Lights
Preset/Off
Lights Mode
7
1 2
3 4
Toggle
up to
Preset/Off
then
toggle
right to
turn the
light off.
Preset/Off
Lights Mode
23
turn the
light on
to the
previous
bright/dim
value last
set in
screen #3
+ + + + -
8
1 2
3 4
IR ECU Control
Lights
Preset/Off
Lights Mode
Press
Mode
button
when
finished
101519 Rev. A
Q R- E D
VII.
F.
6. Blinds
The blinds function is designed to work in conjunction with Hunter Douglas® remote controlled Alustra Duette Honeycomb Shades. These shades feature an IR receiver for remote
control operation.
IR Receiver
The “Blinds” menu (#3) features two options: Blinds 1 and Blinds 2. These options correspond to two channels built into the blind’s motor. The “Channel Selection” section of the
Blind’s Owner’s Guide details how the blinds can be programmed to respond to either
channel 1 (Blinds 1) or channel 2 (Blinds 2) commands. (Note: Blinds ship from the factory
set to channel 1 (Blinds 1) by default.)
NOTE:
The blinds require only a quick toggle command in the direction indicated by the arrow boxes.
A second toggle command in the same direction stops the blind’s motion.
1
+ + + +
1 2
3 4
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
Toggle
down to
Blinds
then
toggle
right
+ + + + +
Blinds 1
Blinds 1
Blinds 2
Blinds1 Open
Blinds 1
Toggle
Right
Quick
toggle up
again stops
the blind’s
motion
Quick
toggle up
to open
the blinds
Blinds 1 Close
5
+ + + +
Blinds 1
Blinds 1 Close
6
1 2
3 4
IR Control
IR ECU Control
Blinds1 Open
Blinds 1 Close
101519 Rev. A
3
IR ECU Control
Blinds
4
Blinds1 Open
2
1 2
3 4
Quick
toggle
down to
close the
blinds.
Toggle left
to exit.
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
24
Press
Mode
button
when
finished
Hunter Douglas
Remote Controlled
Alustra Honeycomb
Shades
Q R- E D
VII.
F.
7. Curtains
The “Curtains” function is programmed for use with the CM101 Makita® Automatic
Drapery Opener System. Setup instructions are included with the packaging.
Once the system is installed, toggle down and right to the “Curtains” menu (#2). The boxed
arrows indicate the toggle direction for each command. Unlike the blinds, each direction features its own independent stop command. Make sure the Enhanced Display is pointing at the
black IR remote receiver connected to the motor housing (see photo below).
An IR indicator will
flash red
when
commands
are
received.
CM101 Makita®
Automatic Drapery
Opener System
(See page 16 to navigate to #1)
+ + + +
IR Menu
IR ECU Control
Mouse Screen
X10
Telephone
GEWA
Lights
Blinds
2
1
1 2
3 4
+ + + +
Curtain Open
Toggle
down to
Curtains
(off screen)
then
toggle
right
Curtain Stop
Curtains
Curtain Stop
Toggle up to open.
Toggle left to stop.
Toggle down to close.
Toggle right to stop.
Press Mode Button to exit.
Curtain Close
25
3
1 2
3 4
IR Control
IR ECU Control
X10
Telephone
GEWA
Lights
Blinds
Curtains
Press
Mode
button
when
finished
101519 Rev. A
Q R- E D
VII.
G.
G. OTHER REMOTE-LOCATION CONTROL
OPTIONS
1
Both IR and X10 devices require line-of-sight access to the IR signal
receivers. In some cases, this presents a problem for individuals
who need to access electronic devices that are not within their
visual field. There are three ways to accomplish this:
1. X10 wire transmission to a remote location
2. Infrared (IR) to Radio Frequency (RF) to Infrared (IR) transmission
3. Infrared (IR) to Radio Frequency (RF) to Infrared (IR) to X-10
transmission
1. X10 Wire Transition to a Remote Location
As mentioned in a previous section, the X10 system broadcasts
through the house wiring. As long as the IR controller
(Powerhouse) is set to the same letter code as the X10 receiver,
the signal can be broadcast to any location that connects to the
house wiring. For example, the X10 receiver for “Unit 1” on the
Enhanced Display X10 menu could be located inside the switch
controlling the outside porch lights. If the upstairs bedroom controller and this porch light receiver are set to the same letter code,
a user could turn on the outside porch lights from the upstairs bedroom.
2
2. Infrared (IR) to Radio Frequency (RF) to Infrared (IR)
Transmission
A second way to access a remote location is to convert the infrared
(IR) signal into a radio frequency (RF) signal and then back into an
infrared (IR) signal. In this example, a TV in the living room is
turned off from the upstairs bedroom.
This transmission is accomplished by transforming the IR signal into
an RF signal using an RF Powermid® pyramid transmitter and
then back into an IR signal using a Powermid® pyramid receiver.
Other products, such as the Leapfrog® transmitter accomplish the
same end. Local electronics specialty stores and the internet feature lists of available products.
3. Infrared (IR) to Radio Frequency (RF) to Infrared (IR) to
X-10 Transmission
A third way to access a remote location is to convert the IR signal
into an RF signal and then back into the IR signal using Powermid®
pyramids. The receiver pyramid then broadcasts the IR signal to an
X10 controller (powerhouse), which converts it into an electronic
pulse that travels through the house wiring to an X10 receiver
switch. This switch opens the circuit of the electric light or appliance.
This setup is often used to open garage doors using an IR transmitter.
101519 Rev. A
Powermid® Transmitter
Powermid® Receiver
3
26
Q R- E D
V I I I . FAU LT S M E N U
VIII. FAULTS MENU
(Accessible to all user levels)
DESCRIPTION
“Faults” in general describe error messages for any electro/mechanical problems a chair may
have. For example, let’s say the chair is intermittently turning off due to a loose connection
between the handcontrol and the controller. Navigating to the Handcontrol fault menu provides information on any possible faults with the handcontrol. In this case, a “Communication
Error” message will appear. When this fault code is reported to a supplier or wheelchair
technician, it allows them to quickly diagnose the problem. Like a warning light on the dashboard of a car, the fault code pinpoints the problem with speed and accuracy.
+ -
1 2
3 4
Faults
Motor Controller
If you encounter a fault, contact your wheelchair supplier.
Sample menu breakdown for the
Handcontrol fault menu. All fault
codes are listed in the Menu Item
Appendix of this manual.
1 2
3 4
27
Sample Faults
menu
Comms err
2
101519 Rev. A
Q R- E D
I X . O P E R AT E M E N U
IX. OPERATE MENU
(Accessible to user levels 2-5)
A. DESCRIPTION
The Operation Menu is designed to provide a user with the ability to operate, test, and control various aspects of the chair through means other than the handcontrol.
+ +
B. DRIVER MENU
Operate
Driver Menu
The driver menu, as outlined on page 8 provides a list of commonly used menu items.
Sample Driver
menu
101519 Rev. A
28
Horn
IR Control
Satellite
GEWA
All Lights On
All Lights Off
1 2
3 4
Q R- E D
IX.
C. POWERED SEATING
The Powered Seating menu controls the various user-powered seating functions. The 1st
level sub-menus list all the powered seating functions provided on the chair. These may be
one or up to six depending on the chair. Operation of each function is found on the third
level in the form of a 4-choice operation box. These boxes provide the option to extend
(or move up) the actuator, retract (or move down) the actuator, return to the Drive
Display, or exit to the 2nd level menu.
Up
Escape
Sample of
Tilt 4-choice
operation
menu*
29
Tilt
Drive
Down
101519 Rev. A
Q R- E D
IX.
D. IR CONTROL
IR controls are accessible through either the Drive Menu or through the Main Menu. IR
Control Functions are in the InfraRed (IR) Control functions menu (see page 13).
+ +
Sample of IR
Control menu
101519 Rev. A
30
1 2
3 4
Operate
IR Control
IR AV Control
IR ECU Control
IR Setup
Q R- E D
IX.
E. DRIVE PROFILES
The Drive Profiles sub-menu provides a user the option of switching from the current
drive profile to a new drive profile. Each drive profile contains operational settings, such as
max speed, min speed, turning speed, acceleration values, etc. The Drive profile also specifies the input device used to drive the chair. A user often switches drive profiles when
transitioning from one type of input device to another. From the factory, each drive profile
is set with progressively faster settings: Drive Profile 1, slowest; Drive Profile 4, fastest.
Drive Profiles can be re-programmed by a qualified supplier or technician.
Drive Profile 1
Drive Profile 4
*Drive Profile
4-choice
operation
menu
Drive 1
Drive 2
Bat
00000 mi
Drive 3
Bat
0.0 mi
00000 mi
00000 mi
31
Drive Profile 3
Drive Profile 2
Drive 4
Bat
0.0 mi
Drive Profiles
Bat
0.0 mi
00000 mi
0.0 mi
101519 Rev. A
Q R- E D
IX.
F. QR-ECM
The QR-ECM (Environmental Control Module) module is used to interface with environmental controls, such as a computer or communication device. Each module contains one
channel with 5 relays and a second channel with 4 relays. These relays are used to translate input commands into output operations on an external device, such as a computer.
For example, a relay might move a computer cursor in a specific direction on the computer screen: activating relay 1 moves the cursor up, relay 2 moves the cursor to the right,
etc. Individual relay activation is available on each Channel sub-menu (see below). See
chair supplier or technician for more details on ECM instruction and setup.
+ + -
1 2
3 4
ECM
Channel 1
Sample of
Channel 1
sub-menu
Enhanced Display Module
101519 Rev. A
32
Relay 1 M
Relay 2 M
Relay 3 M
Relay 4 M
Relay 5 M
off
off
off
off
off
Q R- E D
IX.
G. MISC. MENUS
There are three “misc.” sub-menus. The functions of each are listed below.
+ -
1 2
3 4
Operate
Misc.
Sleep
Mode
Horn
+ -
1 2
3 4
Operate
ECM Misc.
Select 1
+ -
1 2
3 4
Operate
ED Misc.
Backlight On/Off
Contrast
Trip Reset
0%
Definitions
Definitions
Definitions
Sleep: Places the chair in a
sleep (or suspended) state
that is designed to conserve
power. Hold the mode
command for 6 seconds to
re-awaken the chair.
Select 1: Activates the
select relay in port 1
(relay 5).
Backlight On/Off: Turns on
and off the Enhanced
Display backlight.
Mode: Duplicates a mode
command input.
Contrast: Increases or
decreases the screen contrast.
Trip Reset: Resets the
“trip” odometer.
Horn: Sounds the horn.
33
101519 Rev. A
Q R- E D
X . M O N I TO R M E N U
X. MONITOR MENU
(Accessible to user levels 3-5)
A. MOTOR CONTROLLER
The Monitor Menu is designed to monitor real-time electrical systems without actually
physically accessing these systems with testing equipment. For example, if a supplier needs
to know how many ohms of resistance the left break is producing, a user can view this
information in the monitor menu and relay it to the supplier/technician. The following
pages contain various menu trees that outline where this information resides. More technical definitions of specific menu items, such as Actuator 1/counts, can be found in the
Menu-Item Appendix B.
+ + -
1 2
3 4
Motor Controller
Motor I R and V
Quickie Motor Controller
101519 Rev. A
Sample of a
Monitor
sub-menu with
technical data
34
Left Right
Current
0.00 0.00A
Voltage
0.0
0.0V
Resistance 0.050 0.050Ω
RPM
0
0
Q R- E D
X.
B. SYSTEM AND J/S 3-BUTTON
System is an excellent way to determine the actual state of the batteries.
J/S 3-Button helps technicians to determine whether a handcontrol button is functional
or if the problem is somewhere else. This sub-menu also helps quantify joystick displacement.
Specific menu items are defined in the Menu-Item Appendix B.
Group 24 Battery
Quickie 3-Button Hand Control
35
101519 Rev. A
Q R- E D
X.
C. QR-SCM
The QR-SCM (Specialty Control Module #1) is used to interface with specialized input
devices. The sub-menu is designed to monitor specialized input functions and Sip & Puff
pressure levels. These menus are excellent ways to test input signals from a wide variety of
specialized control devices, including the built-in Sip & Puff port.
Quickie electronics is designed to accommodate up to two SCIM modules. The second
module will appear as “SCIM 2”.
QR-Specialty Control Module
Example of a proportional
head array
Example of a Sip & Puff system
Example of a starboard
101519 Rev. A
36
Q R- E D
X.
D.QR-MAC
The QR-MAC (Quickie Multiple Actuator Controller) is designed to accommodate more
than two power seating actuators. It can handle up to 6 actuators. Each one is fully programmable. The recline system features Quickie Enhanced Recline™. (See supplier for
more details.) Specific menu items are defined in the Menu-Item Appendix B.
QR– Multiple Actuator Controller
Shear
2nd level
sub-menu
CRS Status
SW1 Status
SW2 Status
CRS Status
SW1 Status
SW2 Status
Counts
Current
CRS Status
SW1 Status
SW2 Status
Shear Points
3rd level
sub-menu
CRS Status
SW1 Status
SW2 Status
CRS Status
SW1 Status
SW2 Status
CRS Status
SW1 Status
SW2 Status
37
101519 Rev. A
Q R- E D
X.
E. QR-ECM
The QR-ECM (Environmental Control Module) sub-menus contain basic relay status information. Each relay is set for either momentary activation (M), latched activation (L), or
Latched and Hold activation (H), as well as “on” or “off”. The QR-ECM channel submenus provide status information on each relay as well as the stereo jack. If only one ECM
is present, only Channel 1 and Channel 2 will appear. If 2 ECMs are present, ECM2 and
Channel 3 and Channel 4 will appear. For more information on the ECM usage, contact
the chair’s supplier or technician.
QR-Environmental Control Module
101519 Rev. A
38
Q R- E D
X.
F. QR-ED
The QR-ED (Quickie Enhanced Display) monitor sub-menu provides information on the
Enhanced Display’s current screen settings. These include contrast, backlight timer, and
backlight status. Definitions of each are listed below.
Quickie Enhanced Display
Definitions
Contrast: Displays the screens current contrast level.
Backlight Timer: Displays the number of seconds
before the backlight turns off. This is assuming the
backlight is currently turned on.
Backlight Status: Indicates whether or not the backlight
is currently turned on or off. Useful in very bright light.
39
101519 Rev. A
Q R- E D
X I . I N F O R M AT I O N M E N U
XI. INFORMATION MENU
(Accessible to user levels 3-5)
DESCRIPTION
The Information for each 1st-level menu is identical in the Information sub-menu. It provides important registration information that suppliers and technicians may need to access
to update software and firmware or to troubleshoot a module. A listing of the information
contained on these menus is provided below:
Each 2nd level menu screen contains the following information:
OEM Information:
Displays Sunrise Medical manufacturer setup information
Reconfigured:
Indicates whether or not the Motor Control Module has
been reconfigured.
Model Number:
Displays Motor Control Module model number
Serial Number:
Displays Motor Control Module serial number
Manufacturing date: Displays Motor Control Module manufacture date
101519 Rev. A
Software Version:
Displays Motor Control Module software version
Hardware Version:
Displays Motor Control Module hardware version
40
Q R- E D
X I I . P R I M A RY P RO G R A M M I N G M E N U
XII. PRIMARY PROGRAMMING MENU
(Accessible to user levels 4-5)
A. MOTOR CONTROLLER
The Primary Programming Menu provides access to many basic chair functions, such as
volume levels, actuator speed & acceleration, and Quickie Enhanced Display fine tuning.
The motor controller programming sub-menu provides programming access to the following functions:
Quickie Motor Controller
Definitions
Horn Volume: Sets the volume of the horn as a %
of maximum volume.
Command and Beep: Enables an audio backup
“beep” for all commands.
Beep Volume: Sets the volume of the command
beep.
Backup Alarm: Enables an audio “beep” when the
chair is in reverse.
Keyless Lock: Allows the user to “lock” the power
chair when not in use by holding the mode button
and pushing the joystick forward for more than 5
seconds. This prevents the chair from being turned
on until it is unlocked with the same command.
Speed: Sets the percent of maximum actuator speed.
Acceleration: Sets the percent of maximum actuator
acceleration.
41
101519 Rev. A
Q R- E D
XII.
B. QR-MAC AND QR-ED
The QR-MAC sub-menus provide the ability to program the speed and acceleration of the
recline, tilt, and lift actuators.
The QR-ED (Quickie Enhanced Display) provides adjustment of the contrast and backlight.
See definitions below.
QR– Multiple Actuator Controller
Quickie Enhanced Display
Level 5
access
only
Level 5
access
only
Definitions
Speed: Sets the percent of maximum actuator speed.
Acceleration: Sets the percent of maximum actuator acceleration.
Contrast: sets the contrast level of the enhanced display screen.
Backlight: Enables the backlight feature on the enhanced display
screen.
Backlight Tier: Sets the amount of time the backlight remains
illuminated after the last input command.
101519 Rev. A
42
Q R- E D
X I I I . A D VA N C E D P RO G R A M M I N G M E N U
XIII. ADVANCED PROGRAMMING MENU
(Accessible to user level 5)
A. MOTOR CONTROLLER
1. General
The Advanced Programming sub-menu structure features many of the same menu screens
as the primary programming menu with a few extras. The General sub-menu, for example,
features more sensitive driving parameters. Please contact your chair’s supplier or technician for more detailed instructions on how to set General sub-menu structure menu items.
Quickie Motor Controller
43
101519 Rev. A
Q R- E D
XIII.
2. Drive Profile
The Drive Profile sub-menu allows users to custom program the chair’s performance for
each drive profile. Specific menu items, such as forward speed, reverse speed, turn speed,
etc. are defined in the Menu-Item Appendix B.
Because Quickie controlled wheelchairs are designed to meet a wide range of needs and
conditions, it may be possible to program its operating characteristics beyond the user’s
ability to control the chair. We recommend starting with settings below the desired performance and work up. We also recommend that users disengage the motors (place in
freewheel) while programming. When programming is complete, the motors should be reengaged to test the new profiles. We recommend seeking assistance from the chair’s supplier or technician when first learning how to program the drive profiles.
NOTE:
It is important to remember, when adjusting individual parameters, speed (forward or turning) is
independent of acceleration, and acceleration (forward or turning) is independent of deceleration.
Quickie Motor Controller
101519 Rev. A
44
Q R- E D
XIII.
3. System & Actuators
Primary programming menu-item definitions for the System and Actuator sub-menus are
listed on page 41. Advanced programming menu items not included in the primary programming menu are:
Enable: Ability to turn on or off actuator.
Limit Count Up & Limit Count Down: Please contact your chair’s supplier or technician
for instructions on setting the Limit Count Up and the Limit Count Down.
Quickie Motor Controller
45
101519 Rev. A
Q R- E D
XIII.
B. QR-SCM 1
The QR-SCM sub-menu structure provides menu options to fine-tune the control of specialized control devices (such as proportional head controls, Sip & Puff controls, touch-pad
controls, etc) so these systems are more user friendly. Please contact your chair’s supplier
or technician for more detailed instructions on how to program SCIM 1 sub-menu structure
menu items.
NOTE:
If two SCIMs are present, SCIM 2 will also appear. The menu structure is identical.
Specialty Control Input Module
Example of a Head Array
Example of a Star Board
101519 Rev. A
46
Q R- E D
XIII.
C. QR-MAC
The QR-MAC sub-menu structure allows a user to fine tune the function of the chair’s
power actuators (power tilt, power recline, power lift, power elevating footrests, etc.).
Using the QR-MAC controls, a user can turn the power seating actuators on and off, set the
actuators speed, acceleration, and (in the case of the lift) maximum actuator extension. See
definitions below.
QR– Multi Actuator Controller
Definitions
Enabled: Enables the actuator function.
Speed: Sets the percent of maximum actuator speed.
Acceleration: Sets the percent of maximum actuator acceleration.
Max Limit: Determines the maximum extension of the actuator
(or height of the lift).
47
101519 Rev. A
Q R- E D
XIII.
D. QR-ECM
The QR-ECM sub-menu structure provides greater control of the channel relay functions
used in operating environmental controls, such as a Dynavox communication system. Relay
switches can be set for momentary, latched, and latched & hold modes. Please contact your
chair’s supplier or technician for more detailed instructions on how to program ECM 1 submenu items.
NOTE:
If two ECMs are present, ECM 2 will also appear. The menu structure is identical.
Environmental Control Module
101519 Rev. A
48
Q R- E D
XIII.
E. QR-ED
The QR-ED (Quickie Enhanced Display) advanced programming sub-menu provides almost
complete control over every facet of the Enhanced Display. It allows a user to customize
scroll speeds, display language and display lighting. See definitions below.
Quickie Enhanced Display
Definitions
Contrast: Sets the contrast level of the enhanced display screen.
Back Light: Enables the backlight feature on the enhanced display screen.
Backlight Timer: Sets the amount of time the back light remains illuminated after the
last input command.
Language: Determines the language used for all Enhanced Display text.
Caution: It is important to be able to read the language selected. Users who switch to a
different language are sometimes unable to find this menu selection again to switch back
to their native language. If this occurs, please contact Sunrise Medical customer support at
1-800-456-8166. (“Language” is “Sprache” in German and “Taal” in Dutch.)
Units: Determines whether the numerical units used on the Enhanced Display are English
or Metric.
Trip Reset: Determines whether the trip odometer resets when the chair is charged or is
manually reset.
Auto Scroll Mode: Signals the highlight bar to automatically start scrolling down any list
of menu options on the Enhanced Display. When an option appears that the user wants to
select, the right command must be executed.
Auto Scroll Speed: Sets the speed the auto-scroll highlight bar moves from one item to
the next.
Manual Scroll Start: If the up or down input command is maintained for a length of
time specified by this menu item, the highlight bar will start scrolling through the menu
automatically. The minute this command is released, the highlight bar stops scrolling.
Manual scroll is often used to increase scrolling speed.
Manual Scroll Speed: Sets the speed the highlight bar moves from one item to the next
when the up or down input command is held in place.
49
101519 Rev. A
Q R- E D
X I V. M A I N T E NA N C E A N D C A R E
Clean the screen and case as needed using a soft, dry cloth. A small
amount of isopropyl alcohol on the cloth dampened with water
may also be used if dirt and smudges are resistant. Do not use
abrasive cleaning agents or dirty fabric as they may scratch the
screen. Avoid using ammonia or other harsh chemicals.
X V. WA R R A N T Y
1. TWO YEAR WARRANTY
4. WHAT YOU MUST DO
a. Return the warranty card.
b. Obtain from us, while this warranty is in effect, prior
approval for return or repair of covered parts.
c. Return the QR-ED, freight pre-paid, to Sunrise Mobility
Products Division at: 2842 Business Park Ave., Fresno, CA
93727-1328.
d. Pay the cost of labor to install or repair parts.
Sunrise Medical warrants the QR-ED (Quickie Enhanced Display)
against defects in materials and workmanship for 2 years from the
date of first consumer purchase.
2. LIMITATIONS
a. We do not warranty damage due to:
• Neglect, misuse, or improper installation of repair.
• Use of parts or changes not authorized by Sunrise.
b. This warranty is void if the original Enhanced Display serial
number tag is removed or altered.
c. This warranty applies to the USA only. Check with your supplier to find out if international warranties apply.
5. NOTICE TO CONSUMER
There are no other express warranties. To the extend permitted by
law, any implied warranty (including a warranty of merchantability
or fitness for a particular purpose) is limited too:
a. One (1) year from the first consumer purchase, and
b. Repair or replacement of the defective part only.
This warranty gives you certain legal rights. You may also have
other rights that may vary from state to state.
3. WHAT WE WILL DO
Our sole liability is to repair or replace covered parts. This is your
only remedy for consequential damages.
101519 Rev. A
50
Sunrise Medical Inc.
7477 East Dry Creek Parkway
Longmont, Colorado 80503
USA
(800) 333-4000
In Canada (800) 263-3390
www.sunrisemedical.com
©2006 Sunrise Medical Inc. 7.06
101519 Rev. A