No category

Download SLV-662HF/679HF

Transcript

SLV-662HF/679HF
RMT-V266
SERVICE MANUAL
US Model
Canadian Model
SLV-662HF/679HF
PX Model
SLV-679HF
G
j
Photo: SLV-679HF
RMT-V266
S MECHANISM
Refer to the SERVICE MANUAL of VHS
MECHANICAL ADJUSTMENT for
MECHANICAL ADJUSTMENTS. (9-921-647-11)
SPECIFICATIONS
VIDEO CASSETTE RECORDER
MICROFILM
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
7.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the line cord for cracks and abrasion.
Recommend the replacement of any such line cord to the
customer.
Check the B+ voltage to see it is at the values specified.
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.
2.
3.
A commercial leakage tester, such as the Simpson 229 or RCA
TW-540A. Follow the manufacturers' instructions to use these
instruments.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indication
is 0.75V, so analog meters must have an accurate low voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
—2—
TABLE OF CONTENTS
SERVICE NOTE
1.
ERROR CODE INDICATION ··········································· 4
1.
GENERAL
Index to parts and controls ························································ 1-1
Step 1 Unpacking ······································································ 1-2
Step 2 Setting up the remote commander ·································· 1-2
Step 3 Hookups ········································································· 1-3
Selecting a language ·································································· 1-7
Setting the clock ········································································ 1-7
Presetting channels ···································································· 1-9
Setting up the VCR Plus+ system ············································ 1-11
Playing a tape ·········································································· 1-12
Recording TV programs ·························································· 1-13
Recording TV programs using the VCR Plus+ system ··········· 1-13
Setting the timer manually ······················································ 1-14
Playing/searching at various speeds ········································ 1-15
Setting the recording duration time ········································· 1-15
Checking/changing/canceling timer settings ··························· 1-16
Recording stereo and bilingual programs ································ 1-16
Adjusting the picture ······························································· 1-17
Changing menu options ··························································· 1-17
Editing with another VCR ······················································· 1-17
General setup information ······················································· 1-18
Troubleshooting ······································································· 1-18
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
UPPER CASE, PANEL BLOCK ASSEMBLY ·················· 1
DS-84 BOARD ··································································· 1
REAR PANEL ···································································· 2
MA-341 BOARD ······························································· 2
MECHANISM DECK ························································ 3
INTERNAL VIEWS ··························································· 4
CIRCUIT BOARDS LOCATION ······································ 5
3.
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
OVERALL BLOCK DIAGRAM ···································· 3-1
VIDEO BLOCK DIAGRAM ·········································· 3-3
SERVO/SYSTEM CONTROL BLOCK DIAGRAM ····· 3-5
AUDIO/TUNER BLOCK DIAGRAM ··························· 3-7
POWER BLOCK DIAGRAM ········································· 3-9
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ································ 4-3
4-2. PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAMS ···································································· 4-5
• MA-341(1/7) (VIDEO)
SCHEMATIC DIAGRAMS ······················· 4-5
• MA-341(2/7) (AUDIO)
SCHEMATIC DIAGRAMS ······················· 4-7
• MA-341(3/7) (SERVO/SYSTEM CONTROL)
SCHEMATIC DIAGRAMS ······················· 4-9
• MA-341(4/7) (AUDIO PROCESS)
SCHEMATIC DIAGRAMS ····················· 4-11
• MA-341(5/7) (TUNER)
SCHEMATIC DIAGRAMS ····················· 4-13
• MA-341(6/7) (MODE CONTROL)
SCHEMATIC DIAGRAMS ····················· 4-15
• MA-341(7/7) (POWER SUPPLY)
SCHEMATIC DIAGRAMS ····················· 4-17
• MA-341 (VIDEO, AUDIO, SERVO/SYSTEM
CONTROL, TUNER, POWER SUPPLY)
PRINTED WIRING BOARD ·················· 4-19
• DS-84 (TAPE OPARATION)
SCHEMATIC DIAGRAMS ····················· 4-22
• DS-84 (TAPE OPERATION)
PRINTED WIRING BOARD ·················· 4-22
5.
INTERFACE, IC PIN FUNCTION
DESCRIPTION
5-1. SYSTEM CONTROL –
MECHANISM BLOCK INTERFACE
(MA-341 BOARD IC160) ··············································· 5-1
5-2. SYSTEM CONTROL –
SERVO PERIPHERAL CIRCUIT INTERFACE
(MA-341 BOARD IC160) ··············································· 5-1
5-3. SYSTEM CONTROL –
SYSTEM CONTROL PERIPHERAL
CIRCUIT INTERFACE (MA-341 BOARD IC160) ······· 5-2
5-4. SYSTEM CONTROL AND RF MODULATOR –
INPUT SELECTION BLOCK INTERFACE
(MA341 BOARD IC160) ················································ 5-2
5-5. SYSTEM CONTROL – VIDEO/RP BLOCK INTERFACE
(MA-341 BOARD IC160) ··············································· 5-2
5-6. SYSTEM CONTROL – AUDIO BLOCK INTERFACE
(MA-341 BOARD IC160) ··············································· 5-2
5-7. SERVO/SYSTEM CONTROL MICROPROCESSOR
PIN FUNCTIONS (MA-341 BOARD IC160) ················ 5-3
6.
ADJUSTMENTS
6-1 MECHANICAL ADJUSTMENTS ································· 6-1
6-2. ELECTRICAL ADJUSTMENTS ··································· 6-1
1.
PREPARATION BEFORE ADJUSTMENT ··················· 6-1
1-1. Equipment Required ························································ 6-1
1-2. Equipment Connection ···················································· 6-1
1-3. Set-up of Adjustment ······················································· 6-1
1-4. Alignment Tape ······························································· 6-1
1-5. Input/Output Levels and Impedance ······························· 6-2
1-6. Adjustment Sequence ······················································ 6-2
2.
POWER SUPPLY CHECK ············································· 6-2
2-1. Output Voltage Check (MA-341 Board) ························· 6-2
3.
SERVO SYSTEM CHECK ············································· 6-3
3-1. RF Switching Position Adjustment (MA-341 Board) ····· 6-3
4.
AUDIO SYSTEM ADJUSTMENT ································· 6-3
4-1. Hi-Fi Audio System Adjustment (Hi-Fi model only) ······ 6-3
4-2. HiFi Switching Position Adjustment (MA-341 Board) ··· 6-4
4-3. Normal Audio System Adjustment ·································· 6-4
4-3-1. ACE Head Adjustment ···················································· 6-4
4-3-2. E-E Output Level Check ················································· 6-4
4-3-3. Frequency Response Check ············································· 6-4
5.
ADJUSTING PARTS LOCATION DIAGRAM ············· 6-6
7.
REPAIR PARTS LIST
7-1. EXPLODED VIEWS ······················································ 7-1
7-1-1. FRONT PANEL AND UPPER CASE SECTION ·········· 7-1
7-1-2. CHASSIS SECTION ······················································· 7-2
7-1-3. MECHANISM DECK SECTION-1 ······························· 7-3
7-1-4. MECHANISM DECK SECTION-2 ······························· 7-4
7-1-5. MECHANISM DECK SECTION-3 ······························· 7-5
7-2. ELECTRICAL PARTS LIST ·········································· 7-6
—3—
SERVICE NOTE
1. ERROR CODE INDICATION
• Error codes are indicated using the lower 5 digits in the fluorescent display tube.
“At this time, Colon “:” between character is not indicated.”
Mode code indication when the error has occurred.
Error code
ERROR CODE
0 No error
1 Cam encoder error Loading direction
2 Cam encoder error Unloading direction
3 T reel error
4 S reel error
5 Capstan error
6 Drum error
7 Error on initializing
8 Cassette loading error
9 Reserve
MODE CODE
0 Power-on eject
1 Power-on initial
2 Power-off eject
3 Power-off stop
4 FF
5 REW
6 REC
7 REC- pause
8 Power-on stop
9 PB
10
11
12
13
14
15
16
17
18
19
FWD x1
FWD x2
CUE
PB-pause
RVS-pause
RVS x1
RVS x2
REV
Power-off initial
Mecha. error (Power off)
—4—
20
21
22
23
24
25
26
27
28
REW play
Cas. loading
Tape loading
Power-off loading
Mecha. error (Power on)
Power-on eject initial
Power-off eject initial
APC REC
Cas. loading
(No auto PB check)
SECTION 1
GENERAL
1-1
SLV-662HF/672HF
This section is extracted from
instruction manual.
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19E
SLV-662HF/679HF
SECTION 2
DISASSEMBLY
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE, PANEL BLOCK ASSEMBLY
1 Tapping screw
3 Upper case
2 Tapping screw
Hooks
Hooks
!º Panel block assembly
(Engaged by the hook.)
5 Connector
Hooks
Hooks
2-2. DS-84 BOARD
2 DS-84 board
1 B2.6 × 8
Front panel assembly
2-1
2-3. REAR PANEL
2 Rear panel
(Engaged by the hook.)
Hooks
Hooks
Hooks
1 POWER code stopper
2-4. MA-341 BOARD
1 Sumitite (B3) +BV
1 Sumitite (B3) +BV
2 MA-341 board with
mechanism deck
2-5. MECHANISM DECK
3 Two connectors
6 Two screws
(BVTP 3 × 12)
4 Screw
(BVTP 3 × 12)
2 Screw
(BVTP 3 × 12)
0 Mechanism deck
1 Flexible board
9 MA-341 board
5 MD base (R)
8 MD base (M)
7 MD base (R)
2-6. INTERNAL VIEWS
— Top View —
M901
Drum Assembly
DZH-0A7A/Z-RP 8-839-057-51
ACE head block assembly
A-6759-620-A
Pinch press block assembly
A-6759-615-A
FE head
1-500-144-11
FL complete assembly
A-6759-619-C
Reel (T) table
3-977-508-01
Reel (S) table
3-977-507-01
— Bottom View —
M902
DC motor (capstan)
1-698-971-11
Rubber belt
3-977-510-01
M903
Cam motor assembly
X-3947-577-1
2-7. CIRCUIT BOARDS LOCATION
MA-341
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER, POWER SUPPLY
DS-84
(TAPE OPERATION)
2-5E
SLV-662HF/679HF
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
MA-341 BOARD
IC160
(SEE PAGE 4-5,7,9,11,13,15,17)
SYSTEM
CONTROL
DRUM MOTOR
(2/2)
DRUM
SERVO
D VS
M
DRUM
MOTOR
D PG
DRUM
PG
D FG
DRUM
FG
IN
OSD
RF VIDEO
VIDEO
(1/2)
AUDIO
4CH
S701
R
CJ561
3CH
LINE 1
IN
L VIDEO 1
VIDEO
CAPSTAN MOTOR
M
CJ561
LINE
OUT
L
Y/C
PROCESSOR
CAPSTAN
SERVO
CAP VS
RF CH
TU VIDEO
JS202
RF AUDIO
VIDEO
IC201
TU701
OUT
(1/2)
RF VIDEO
IC160
VHF/
UHF
TV/VTR
CAP FG
CAPSTAN
MOTOR
CAPSTAN
FG
PLL DATA
PLL CLOCK
PLL ENB
AFT
CTL REC/PB
CTL
AMP
TU VIDEO
VIDEO
HEAD
PB Y/C
SP
CH 1
IC260
SP
CH 2
IC101
REC Y/C
Q VD
Q VD
CAM +,-
LOADING
MOTOR
I2C DATA
VIDEO
REC/PB
QAMP
M
I2C CLK
MODE1-4
EP
CH 1
EP
CH 2
C SYNC
C SYNC
HA SWP
HA SWP
RF SWP
RF SWP
RF ENV
RF ENV
ROTARY
SWITCH
T REEL FG
SW12V
PH102
T REEL
S REEL FG
AL
CH 1
IC360
AUDIO
HEAD
AUDIO
PROCESSOR
(HIFI)
CH 2
PH101
S REEL
AR
RF AUDIO
T SENS
Q101
T SENS
CJ561
I2C DATA
I2C DATA
L 1(L)
L
LINE 1
IN
AUDIO
L 1(R)
D103
(T/S LED)
S SENS
I2C CLK
I2C CLK
R
AF ENV
AF ENV
AF SWP
AF SWP
Q102
S SENS
Q103
T/S LED
LED
DRIVE
IC201
NORM OUT
NORM IN
ND420
FLUORESCENT
INDICATOR TUBE
SIGNAL
CONTROL
IC420
IC161
(SEE PAGE 4-22)
S401,402,404,405
S408,412,422,423
FUNC KEY 1
IC162
A HEAD PB
POWER
FAIL DET
IC331
A HEAD REC
HEAD
SW
FUNC KEY 2
RESET
PULSE GEN
T301,Q303
BIAS
ERASE
OSC
ERASE
HEAD
+F
FL
DRIVE
EEPROM
NORMAL
AUDIO
-F
(2/2)
AUDIO
PROCESSOR
(MONO)
REC/
PB
LOADING
MOTOR
IC403
REMOTE
CONTROL
RECEIVER
FULL
ERASE
HEAD
16
3-1
3-2
FUNCTION
KEY
DS-84 BOARD
S442,443,444,446
FUNCTION
KEY
SLV-662HF/679HF
3-2. VIDEO BLOCK DIAGRAM
IC201 @ª PB
IC201 @ª REC
H
2.2Vp-p
H
2.3Vp-p
IC160 %™
MA-341 BOARD
FROM
SYSCON IC160 13
BLOCK
(SEE PAGE 3-5)
OSD V OUT
REC
2.2Vp-p
H
Q VD
IC160 %™ OSD V OUT PB
IC201 @£ PB
H
H
FROM
TUNER
BLOCK
(SEE PAGE 3-6)
CJ561
25
IC201 #¶ REC
TU701 28 TU VIDEO
H
IC160
Q VD
LINE 1
IN
IC201
1.0Vp-p
CHARA
INS
6dB
AMP
JS202
29
Q502
(1/2)
OSD
KIL
B.D
39
CLP
37
CLP
35
CLP
(1/3)
OSD
Y/C PROCESSOR
VIDEO
50 OSD V IN
OSD V OUT 52
CJ561
Q500
Q561
BUFFER
BUFFER
RF VIDEO
23
VIDEO
AGC
31
IC160 %º OSD V IN REC
R
FBC 1/2
P
YNR
43
46
1H
DL
BUFFER
H
2.2Vp-p
IC160 %º OSD V IN PB
CLP
41
PIC
CONT
P
4.2Vp-p
H
47
P R
R
SYNC
SEP
28
LPF
P
Y/C
MIX
IC201 @• REC/PB
H
CLK IN 50
IC260 7 PB
DHP
NC
61
53
59
55
2.3Vp-p
IC260
VIDEO REC/PB AMP
DRUM
VIDEO
HEAD
SW5V
PB
CN260
16
11
L270
SP
CH1
INV
N.L
De-EM
0.4Vp-p
V
PB
0.4Vp-p
R
6
R
PB
24
EP
CH1
COMP
PB
ENV SW
4
BPF2
Q202
R
SUB
BPF
P
BUFFER
10
17
CLP
SQPB
EQ
FM
AGC
IC201 ^¶ REC/PB
HA
CONT
12
MAIN
CONV.
SUB
COMV.
1
2
21
13
EP
CH2
7
BACK UP
AMP
C
LPF
P
PB RF
8
ACC
AMP
P
R
DL
EQ
BPF1
P
ENV RF ENV
6
DET
9
63
LPF
19
7
SP
CH2
52
AMP
5
C SYNC
1H/2H
DL
IC201 1 PB
13
SW3
10
HA SWP
IC260 4 REC/PB
S
PB
EQ
Q201
3
REC
6
BUFFER
DOUBLE
LIM
N
SUB
LPF
DEM
PB
BGA-B
8
B
PB
BGA-A
17
V
REC
APC
PA
VXO1
4
66
R
IC260 5 REC/PB
AGC
DET
3.579545MHz 460mVp-p
67
X201
3.579545MHz
P
3.6Vp-p
RF SWP
REC
BGA
IC201 2 REC
65
KIL
ATT
22
REC C
VCO
3.4Vp-p
H
REC
10
REC RF
AGC
2
9
7
REC H 11
60
REC Y RF REC
EQ
FM
MOD
2
3
N.L
EMPH.
MAIN
EMPH.
95 REC H
SERIAL
DECODER
16 REC CUR ADJ
TRICK H
99 TRICK H
PB RF
IC260 9 REC
RF SWP
DETAIL
ENH
RF SW P
REC/PB
IC201 (•
REC CUR ADJ
CHECK
PIN
480mVp-p
SLD
1 12
CN270
62
REC C
H
30Hz
1.5Vp-p
RW SWP
HA SWP
C ROT
98
97
96
21
20
IC201 7 REC
IC260 @™ REC
0.1µsec/div
50mV/div
0.1µsec/div
0.1V/div
0.1µsec/div
0.5V/div
I2C DATA
IC160 72
I2C CLK
IC160 71
C ROT
IC160 15
C SYNC
IC160 58
RF ENV
IC160
ENV SW
IC160 17
8
HA SWP
IC160 16
RF SWP
IC160 18
FROM/TO
SYSCON
BLOCK
(SEE PAGE 3-5)
16
3-3
C VIDEO IN
REC/PB
IC160 %§
Q203
R
LINE
OUT
VIDEO
56 C VIDEO IN
24
32
2.3Vp-p
480mVp-p
3-4
H
2.1Vp-p
TU701 5
TO
TUNER
BLOCK
(SEE PAGE 3-6)
SLV-662HF/679HF
3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM
MA-341 BOARD
(SEE PAGE 4-9,13)
IC160
UNSW 5V
1
VCC
M901
L162
D162
IC160
IC162
(2/3)
3
3
D PG
90 DRUM PG
4
D FG
M12V
CN102
VM
7
7
VCC
1
1
TL
6
6
PH102
T REEL
FG
79 S REEL FG
PS101
PH101
S REEL
FG
U
3
3
CAPSTAN
FG
CAP RVS
CAP FG
L
R
MUTE
F MONO
SAP 86
F MONO 84
FL DRIVER
6 S SENS
6 D IN
S CLK 70
8 CLK
15
ND420
S16 30
9 CS
G2
43
G7
38
VACUUM FLUORESCENT
INDICATOR TUBE
F-
LED
DRIVE
87 CAP FG
S OUT 68
FLD CS 66
Q102
SUPPLY END
SENSOR
Q103
24 CAP RVS
S1
5 D OUT
S IN 69
T/S LED
76 CAP ERR
IC420
Q101
TAKE END
SENSOR
D103
2
MODE
STEREO 85
TA MUTE 62
W-
2
DET
PLL CLK 59
7 T SENS
W
SAP IND
PLL DATA 60
MAIN/SAP 83
4.0Vp-p
360Hz
LIMITER
CVS
32 33 34 35 36
TU AFT 3
DRUM FG
REC/PB
D5V
5
27 4
ANT SEL 21
SW5V
W+
5
VIDEO
13 12 11
PLL ENABLE 61
V-
V
SW
14 REMCON
80 T REEL FG
89 DRUM FG
IC160 *ª
SW5V
V+
1
38 37
OUT
2
SW12V
4
IN
VHF/
UHF
28
ST IND
REMOTE
2 CONTROL
RECEIVER
FG
U-
4 CH
4.4Vp-p
PG
U+
3 CH
78 POWER FAIL
IC403
30Hz
DRUM MOTOR
8
TU701
AUDIO
POWER
FAIL
DET.
7
DRUM PG
REC/PB
MATRIX
CAPSTAN
MOTOR
5 1
S701
CONT
IC160 (º
M902
34 RST
RF UNIT
OUTPUT
HALL
DEVICE
6
AFT
5
77 DRUM ERR
ENABLE
D VS
CLOCK
2
RESET
PULSE
GEN.
DATA
2
HALL
DEVICE
RF AUDIO IC360 13
SERVO CONTROL
OUTPUT
M
99 AVCC
L163
98 AMP VCC
1
F+
20 END LED
S101
REC
PROOF
CN161
30 REC PRF
95 CTL +
1
CTL
HEAD
4fsc (out)
REC/PB
IC160 #¢
38 4fSC IN
X160
14.31818MHz
94 CTL -
3
39 4fSC OUT
IC160 #§
IC101
CAM
MOTOR
CN103
M
32kHz (OUT)
REC/PB
14.31818MHz
2
35 32kHz IN
5.0Vp-p
X160
32.768kHz
LOADING
MOTOR DRIVE
36 32kHz OUT
2 CAM -
1
32.768kHz
(SEE PAGE 4-22)
2.9Vp-p
IN2 4
S401,402,404,405
S408,412,422,423
33 CAM
10 CAM +
3
S102
FUNCTION
KEY
FUNC KEY1 5
CAM
ENCODER
4
MECHA
POSITION
2
3
1
MODE1
MODE1
MODE2
MODE2
MODE3
MODE3
MODE4
IC160 $∞
OSC OUT
REC/PB
MODE4
27 MODE3
FF
2
29 MODE1
28 MODE2
DS-84 BOARD
REW
4
FUNC KEY2 4
3
PB/STOP
IC161
L500
24.9MHz
4.6Vp-p
45 OSC OUT
I2C DATA 32
5
I2C CLK 31
6
IC160 %•
IC201 25
IC201 28 ,IC260 5
IC260
TO/FROM
VIDEO
IC260
BLOCK
(SEE PAGE 3-4) IC201 97 ,IC260
IC201 98 ,IC260
Q VD
C SYNC
8 V RF ENV
ENV SW
17 ENV SW
3
HA SWP
16 HA SWP
4
RF SWP
18 RF SWP
C ROT
IC201 20
I2C DATA
IC201 21
I2C CLK
H
72 I2C DATA
71 I2C CLK
IC360 42
I2C DATA
I2C CLK
IC360 44
AF ENV
9 AF ENV
IC360 41
AF SWP
19 AF SWP
TO AUDIO BLOCK Q301 B ,IC360 94
(SEE PAGE 3-8)
A MUTE
4.2Vp-p
1
15 C ROT
IC360 43
TO/FROM
AUDIO
BLOCK
(SEE PAGE 3-7)
C SYNC
REC/PB
58 C SYNC
RF ENV
2
IC201 96
EEPROM
13 Q VD
6
4
2
FUNCTION
KEY
3
S442,443,444,446
26 MODE4
44 OSC IN
Q401
P CONT M12 64
D405
LED
DRIVE
POWER
P CONT M12
P CONT SW12 65
P CONT SW12
TO
POWER BLOCK
(SEE PAGE 3-10)
22 AF REC P
63 A MUTE
16
3-5
FROM
VIDEO
BLOCK
(SEE PAGE 3-4)
37 VCC
D109
CN101
C
TU VIDEO IC201 39
SYSTEM CONTROL
D5V
L161
D161
D6V
M12V
RF VIDEO Q500
(3/3)
3-6
AUDIO L
IC360
2
AUDI R
IC360
3
TO/FROM
AUDIO
BLOCK
(SEE PAGE 3-8)
SLV-662HF/679HF
3-4. AUDIO/TUNER BLOCK DIAGRAM
MA-341 BOARD
(SEE PAGE 4-7,11)
IC360
AUDIO
PROCESSOR
(HIFI)
DRUM
AUDIO
HEAD
CN260
16
37
3
PNR
L
CH1
H
2
BPF
VCO
CH2
35
1
36
MUTE
18
Q380
MUTE
14
MUTE
SW
NA IN
PNR
R
RF AUDIO
NA OUT
LINE 1
IN
SDA
SCL
CJ561
43 42
10 11 6
7
3
2
L
IC201
R
AUDIO
PROCESSOR
(MONO)
AUDIO
REC
(2/2)
EQ
93
89
92
P
R
74
76
78
LINE
AMP
MUTE
80
L1
L2
ALC
TU
81
88 A-H SW
VREF
REC
REC
87
AUTO
BIAS
85
84
82
A MUTE
CHECK
1
REC:EP,LP
PB:EP
HF ADJ
CN270
94
86
A MUTE
CN301
4
AUDIO
REC/PB
HEAD
NOMAL
AUDIO
IC160 63
FROM
SYSCON (SEE PAGE 3-5)
BLOCK
IC331
2
3
AUDIO
ERASE
HEAD
HEAD
4
SW
1
FULL
ERASE
HEAD
1
T301,Q303
Q302
BIAS
ERASE
OSC
BIAS
SW
CN302
TU AUDIO L
TU701 38
TU AUDIO R
TU701 37
I2C DATA
IC160 72
I2C CLK
IC160 71
AF ENV
IC160
AF SWP
IC160 19 22
9
FROM
TUNER
BLOCK
(SEE PAGE 3-6)
FROM/TO
SYSCON (SEE PAGE 3-5)
BLOCK
16
3-7
TU701 1
TO
TUNER
BLOCK
(SEE PAGE 3-6)
21
INPUT SEL
44
MUTE
C389
22
41
R
Q381
MUTE
3-8
CJ561
AUDIO
13
VCO
LEVEL
DET
L
Q382
15
17
OUTPUT SEL
L
MUTE
LINE
OUT
SLV-662HF/679HF
3-5. POWER BLOCK DIAGRAM
MA-341 BOARD
(SEE PAGE 4-17)
TU701
T600
D609
CN600
3
AC
IN
1
F600
LF600
LINE
FILTER
D600
R614
L604
+30V
POWER
TRANS
L601
1
RECT
12V
REG
17 30V
L703
IC601
D608
R705
3 5V
L704
2
15 5V
SW12V
IC160
SERVO/SYSTEM
CONTROL
4
P CONT
65 P CONT SW12
64 P CONT M12
53 OSD VCC
L501
D607
D606
Q601,602,606
L602
PS600
L603
Y/C PROC
AUDIO PROC
Q607
SW5V
SW 5V
REG
L203
L206
PH600
PHOTO
INTERRUPTER
37 VCC
IC201
SWITCHING
REG.
L205
Q608
+B
ADJ
Q603
IC602
L204
NA5V
NA 5V
REG
L304
REG
CONT
98 AMP VCC
IC162
56 CCD VCC
40 SW VCC
RESET
5 VCC2 PULSE
GEN.
5
5 RESET
POWER
FAIL
DET.
8
78 P FAIL
75 A VCC
MTR12V
7 VCC1
T301,Q303
BIAS
ERASE
OSC
IC161
IC403
EEPROM
IC331
REMOTE
CONTROL
RECEIVER
8 VCC
HEAD SW
P CONT
99 AVCC
L163
9 Y VCC
BIAS
SW
Q604,605
L162
D162
58 C VCC
Q302
MOTOR
12V SW
L161
D161
D6V
1 VCC
2 VCC
IC420
D405
IC360
POWER
L420
14 VDD
FLUORESCENT
INDICATOR TUBE
33 VDD
AFM.
AUDIO PROC
ND420
FL DRIVER
45 VDD
L360
F-
40 VCC
34 VCC
34 VEE
F+
PS101
MTR 12V
PH101,102
LOADING
MOTOR
DRIVE
Q101,102
L101
8 VCC1
9 VCC2
L605
L606
16
3-9
1
7
CAPSTAN
MOTOR
IC101
T/S
REEL
T/S
SENSOR
CN102
SW 5V
3-10E
D109
CN101
MTR 12V
1
DRUM
MOTOR
SLV-662HF/679HF
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
MA-341 BOARD
(VIDEO BLOCK (IC260))
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
MA-341 BOARD (VIDEO BLOCK (IC201))
!¶ IC201 2 REC
@¡ IC201 @ª PB
1 IC260 4 REC/PB
For Printed Wiring Boards.
b: Pattern from the side which enables seeing.
For Schematic Diagrams.
Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, because it is damaged by the heat.
All resistor are in ohms, 1/4 W unless otherwise noted.
Chip resistor are 1/10 W unless otherwise noted.
kΩ: 1000 Ω, M Ω, : 1000 kΩ.
All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
C: panel designation.
: internal component.
U : B+ Line.
V : B– Line.
Circled numbers refer to waveforms.
Readings are taken with a PAL color-bar signal input.
Voltage are dc between ground and measurement points.
Readings are taken with a digital multimeter (DC10MΩ).
Voltage variations may be noted due to normal production
tolerances.
H
3.6Vp-p
V
480mVp-p
!• IC201 7 REC
H
2.3Vp-p
@™ IC201 (•
2 IC260 5 REC/PB
0.1µsec/div
0.1V/div
3.4Vp-p
H
RF SW P
REC/PB
30Hz
!ª IC201 @£ PB
1.5Vp-p
@£ IC201 #¶ REC
3 IC260 7 PB
H
0.4Vp-p
V
480mVp-p
@º IC201 @• REC/PB
H
1.0Vp-p
@¢ IC201 ^¶ REC/PB
4 IC260 9 REC
When indicating parts by reference number, please
include the board name.
H
0.1µsec/div
50mV/div
4.2Vp-p
@¡ IC201 @ª REC
3.579545MHz 460mVp-p
@∞ IC201 1 PB
5 IC260 !º REC
• Abbreviation
CND : Canadian
0.4Vp-p
H
H
480mVp-p
6 IC260 @™ REC
0.1µsec/div
0.5V/div
4-1
4-2
2.2Vp-p
SLV-662HF/679HF
4-1. FRAME SCHEMATIC DIAGRAM
FRAME SCHEMATIC DIAGRAM
4-3
4-4
SLV-662HF/679HF
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
MA-341(1/7) (VIDEO) SCHEMATIC DIAGRAMS
— Ref. No. MA-341 Board; 1,000 Series —
For schematic diagram
• Refer to page 4-19 for printed wiring board.
• Refer to page 4-2 for waveforms.
EP_L_IN
_EP_OUT
PB FELT
EP_H_IN
4-5
4-6
VIDEO
MA-341(1/7)
SLV-662HF/679HF
GND
N.C
N.C
CTRL1
VCC.
HEAD
SWITCH
N.C
CTRL2
For schematic diagram
• Refer to page 4-19 for printed wiring board.
• Refer to page 4-2 for waveforms.
MA-341(2/7) (AUDIO) SCHEMATIC DIAGRAMS
— Ref. No. MA-341 Board; 1,000 Series —
AUDIO
MA-341(2/7)
4-7
4-8
SLV-662HF/679HF
MA-341(3/7) (SERVO/SYSTEM CONTROL) SCHEMATIC DIAGRAMS
— Ref. No. MA-341 Board; 1,000 Series —
For schematic diagram
• Refer to page 4-19 for printed wiring board.
• Refer to page 4-21 for waveforms.
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
4-9
4-10
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
SERVO/SYSTEM CONTROL
MA-341(3/7)
SLV-662HF/679HF
MA-341(4/7) (AUDIO PROCESS) SCHEMATIC DIAGRAMS
— Ref. No. MA-341 Board; 1,000 Series —
AUDIO PROCESS
MA-341(4/7)
4-11
For schematic diagram
• Refer to page 4-19 for printed wiring board.
4-12
SLV-662HF/679HF
MA-341(5/7) (TUNER) SCHEMATIC DIAGRAMS
— Ref. No. MA-341 Board; 1,000 Series —
For schematic diagram
• Refer to page 4-19 for printed wiring board.
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
4-13
4-14
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
TUNER
MA-341(5/7)
SLV-662HF/679HF
For schematic diagram
• Refer to page 4-19 for printed wiring board.
MA-341(6/7) (MODE CONTROL)SCHEMATIC DIAGRAMS
— Ref. No. MA-341 Board; 1,000 Series —
MODE CONTROL
MA-341(6/7)
4-15
4-16
SLV-662HF/679HF
MA-341(7/7) (POWER SUPPLY) SCHEMATIC DIAGRAMS
— Ref. No. MA-341 Board; 1,000 Series —
For schematic diagram
• Refer to page 4-19 for printed wiring board.
US, CND:TNR10V241k
PX:TNR10V431k
US, CND:2A 125V
PX:T2AL 250V
C650 0.1uF B
C638
US, CND:470u/10V
PX:22u/25V
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
4-17
4-18
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
POWER SUPPLY
MA-341(7/7)
SLV-662HF/679HF
MA-341 (VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER SUPPLY) PRINTED WIRING BOARD
— Ref. No. MA-341 Board; 1,000 Series —
There are few cases that the part printed on this diagram isn’t mounted in this model.
1-672-475-
VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER SUPPLY
MA-341
4-20
13
SLV-662HF/679HF
DS-84 (TAPE OPERATION) PRINTED WIRING BOARD
— Ref. No. DS-84 Board; 2000 Series —
There are few cases that the part printed on this diagram isn’t mounted in this model.
MA-341 BOARD
CN101
CN102
CN103
CN104
CN161
CN260
CN270
CN301
CN302
CN404
CN600
H-9
F-3
B-6
B-12
A-13
I-10
I-11
G-12
G-12
B-1
I-3
D103
D109
D161
D162
D301
D302
D405
D410
D561
D600
D601
D602
D603
D604
D605
D606
D607
D608
D609
D610
D611
D612
D614
D615
D616
D617
D618
D619
D702
D-7
G-4
D-8
D-8
I-6
I-6
A-13
A-10
I-4
H-1
G-3
F-2
G-1
G-2
F-1
D-1
E-1
E-2
E-2
B-2
C-3
C-3
G-2
H-2
G-2
G-1
C-3
C-1
H-13
IC101
IC160
IC161
IC162
IC201
IC260
IC331
IC360
IC403
IC420
IC601
IC602
A-4
C-10
C-12
C-12
F-10
H-10
G-11
J-9
A-5
A-7
B-2
E-1
MA-341 BOARD (SERVO/SYSTEM CONTROL BLOCK)
4fsc (out)
C VIDEO IN
7 IC160 #¢ REC/PB
!¡ IC160 %§ REC/PB
14.31818MHz
PH101 C-9
PH102 C-6
PH600 F-1
Q101
Q102
Q103
Q201
Q202
Q203
Q302
Q303
Q380
Q381
Q382
Q401
Q500
Q502
Q561
Q601
Q602
Q603
Q604
Q605
Q606
Q607
Q608
8
E-3
E-11
E-7
H-9
G-8
F-9
G-11
G-12
J-8
J-7
J-8
A-13
C-9
C-8
I-6
G-2
H-1
C-3
B-1
C-1
G-2
B-3
F-6
5.0Vp-p
OSC OUT
IC160 $∞ REC/PB
24.9MHz
H
!™ IC160 %•
4.6Vp-p
2.1Vp-p
C SYNC
REC/PB
4.2Vp-p
H
9 IC160 %º OSD V IN REC !£
3
DRUM FG
IC160 *ª REC/PB
MA-341
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER, POWER SUPPLY
H
2.2Vp-p
9 IC160 %º OSD V IN PB
360Hz
DRUM PG
REC/PB
!¢ IC160 (º
4.4Vp-p
30Hz
H
!º IC160 %™
4.0Vp-p
DS-84
(TAPE OPERATION)
2.3Vp-p
OSD V OUT
REC
CTL AMP OUT
!∞ IC160 (¶ REC/PB
MA-341
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER, POWER SUPPLY
DS-84 (TAPE OPARATION) SCHEMATIC DIAGRAMS
— Ref. No. DS-84 Board ; 2000 Series —
4.0Vp-p
2.2Vp-p
H
30Hz
!º IC160 %™ OSD V OUT PB !§ IC160 #§
DS-84
(TAPE OPERATION)
H
4-21
2.3Vp-p
32kHz (OUT)
REC/PB
32.768kHz
2.9Vp-p
4-22E
TAPE OPERATION
DS-84
SLV-662HF/679HF
SECTION 5
INTERFACE, IC PIN FUNCTION DESCRIPTION
5-1. SYSTEM CONTROL — MECHANISM BLOCK INTERFACE
(MA-341 BOARD IC160)
*1
*2
*3
*4
*5
CASSETTE CASSETTE
TAPE
TAPE
STOP
LOARDING UNLOARDING THREADING UNTEREADING
FF
REW
PB
REC
*5
*5
*5
*5
*5
—
H
H
H
H
H
—
—
L
L
L
H
H
—
—
—
H
H
H
L
L
—
—
—
—
H
L
L
L
L
L
*1
*1
*1
*1
*1
*1
*1
*1
*1
I
H/L
H/L
H/L
H/L
H/L
H/L
*2
*2
*2
*2
MA-341 Board
IC160&ª
I
H/L
H/L
H/L
*2
*2
H/L
*2
*2
*2
*2
END LED
MA-341 Board
IC160@º
O
L
*3
*3
*3
*3
*3
*3
*3
*3
*3
T SENS
MA-341 Board
IC1607
I
*3
*3
*3
*4
*4
*4
*4
*4
*4
*4
S SENS
MA-341 Board
IC1606
I
*3
*3
*3
*4
*4
*4
*4
*4
*4
*4
Signal
Pin No.
I/O
EJECTED
CAM
MA-341 Board
IC160#£
O
*5
H
L
H
L
MODE 1
MA-341 Board
IC160@ª
I
—
—
—
—
MODE 2
MA-341 Board
IC160@•
I
—
—
—
MODE 3
MA-341 Board
IC160@¶
I
—
—
MODE 4
MA-341 Board
IC160@§
I
—
REC PRF
MA-341 Board
IC160#º
I
T REEL
MA-341 Board
IC160*º
S REEL
“L” When erasing protection tab is bent. “H” when not bent.
Pulse of period in proportion to reel rotating speed.
Approx. 2 msec period “H” pluse when tape top or end is detected.
Normally “L”. 2 msec period “H” puise when tape top or end is detected.
Hi-Z
5-2. SYSTEM CONTROL — SERVO PERIPHERAL CIRCUIT INTERFACE
(MA-341 BOARD IC160)
Signal
Pin No.
TAPE
TAPE
*7
*7
*3
*3
*4
*4
I
H/L
O
I/O
STOP
FF
O
*7
*7
I
*3
I
REW THREADING UNTEREADING
PB
REC
*7
*7
*1
*3
*3
*3
*3
*4
*4
*4
*4
*4
*2
*2
*5
*5
*2
*2
H/L
L
H
L
H
L
L
O
L
*6
*6
*6
*6
*6
*6
O
*6
*6
*6
*6
*6
*6
*6
MA-341 Board
CTL IN+
DRUM PG
DRUM FG
CAP FG
CAP RVS
CAP ERR
DRUM ERR
*1.
*2.
*3.
*4.
*5.
*6.
*7.
IC160(∞
MA-341 Board
IC160(º
MA-341 Board
IC160*ª
MA-341 Board
IC160*¶
MA-341 Board
IC160@¢
MA-341 Board
IC160&§
MA-341 Board
IC160&¶
30Hz pulse.
Pulse of period in propotion to tape speed.
30Hz “H” pluse.
720 Hz pulse.
Unstable period pulse.
DC voltage 1 – 5V.
Hi-Z (2.5V)
5-1
5-3. SYSTEM CONTROL — SYSTEM CONTROL PERIPHERAL CIRCUIT INTERFACE
(MA-341 BOARD IC160)
Signal
RESET
I2C DATA 1
I2C CLOCK 1
I2C DATA VIDEO
I2C CLOCK VIDEO
(ARC) S OUT 1
(ARC) CLK 1
Pin No.
MA-341 Board
IC160#¢
MA-341 Board
IC160#™
MA-341 Board
IC160#¡
MA-341 Board
IC160&™
MA-341 Board
IC160&¡
MA-341 Board
IC160$™
MA-341 Board
IC160$¡
I/O
I
I/O level
Normally “H”, “L” when service interruption detected or restored.
I/O
Serial communication data to EEPROM I2C161.
O
Serial communication clock to EEPROM I2C161.
I/O
Serial communication data to video and audio microprocessor.
O
Serial communication clock to video and audio microprocessor.
I/O
Serial communication data to ARC microprocessor.
O
Serial communication clock to ARC microprocessor.
5-4. SYSTEM CONTROL AND RF MODULATOR — INPUT SELECTION BLOCK
INTERFACE (MA-341 BOARD IC160)
Signal
Pin No.
MA-341 Board
IC160@¡
ANT SEL
I/O
O
I/O level
“L” when RF modulator through.
5-5. SYSTEM CONTROL — VIDEO/RP BLOCK INTERFACE (MA-341 BOARD IC160)
Signal
RF SWP
QVD
C SYNC
Pin No.
MA-341 Board
IC160!•
MA-341 Board
IC160!£
MA-341 Board
IC160%•
I/O
STOP/FF
/REW
TAPE
LOADING
TAPE
UNLOADING
PB
REC
REC
PAUSE
O
*1
*1
*1
*1
*1
*1
O
L
L
L
*2
L
L
I
*3
*3
*3
*3
*3
*3
*1. Synchronized with drum rocation, 30Hz 50% duty pulse.
*2. Normal “L”, “H” when video signal is not rgenerated.
*3. Composite sync signal (positive).
5-6. SYSTEM CONTROL — AUDIO BLOCK INTERFACE (MA-341 BOARD IC160)
Signal
A MUTE
AF REC P
•
Pin No.
MA-341 Board
IC160^£
MA-341 Board
IC160@™
I/O
STOP/FF
/REW
TAPE
LOADING
TAPE
UNLOADING
PB
REC
REC
PAUSE
O
L
L
L
L
L
H
O
L
L
L
L
L
H
Abbreviation
CND : Canadian
5-2
5-7. SERVO/SYSTEM CONTROL MICROPROCESSOR PIN FUNCTIONS
(MA-341 BOARD IC160)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Pin Name
DEST
FULL ERS
TU AFT
FUNC KEY2
FUNC KEY1
S SENS
T SENS
V RF ENV
AF ANV
CBC ON
KKP+
KKP–
QVD
REMOCON
C ROT
HA SWP
ENV SW
RF SWP
AF SWP
END LED
ANT SEL
AF REC P
FE ON
CAP RVS
SUR ON
MODE4
MODE3
MODE2
MODE1
REC PRF
I2C CLK EEP
I2C DATA EEP
CAM
RESET
32kHz (in)
32kHz (out)
Vcc
4fsc (in)
4fsc (out)
Vss
ARC CLK
ARC DATA
CLK SEL
OSC IN
OSC OUT
NUB
LPF
SP
OSD GND
OSD V IN
I/O
I
I
I
I
I
I
I
I
O
I
I
O
I
O
O
I
O
O
O
O
O
O
I
I
I
I
I
I/O
I/O
O
I
I
O
I
I
O
O
O
I
I
O
I/O
O
I
Function
Destination control input
NC
Tuner analog AFT input
Key input
Key input
Tape end sensor input
Tape top sensor input
Video playback signal envelope input
Hi-Fi audio playback signal envelope input
Cable box control signal output
ETR pulese signal input
ETR pulese signal input
Quasi VD pulese output
Remote sires signal input
Head AZ signal output
SP/EP changed head signal
SP/EP head output lebel ditaction signal
VIDEO RF switching pulse output.
AF switching pulse output.
END sensor LED output
TV/VTR RF modulator control output
Hi-Fi record control pulse output.
NC
Capstan reverse control
NC
Mechanism section CAM encoder input (data4)
Mechanism section CAM encoder input (data3)
Mechanism section CAM encoder input (data2)
Mechanism section CAM encoder input (data1)
Erasing protection tab, cassette IN detection input
HC CLOCK line (EEPROM)
HC DATA line (EEPROM)
Cam motor control signal output
System reset input
Sub clock 32MHz
Sub clock 32MHz
5V
Main clock input
Main clock output
Ground
Rearityregenarator (ARC) control clock signal
Rearityregenarator (ARC) control data signal
CLOCK seleal “L” Sub clock, “H” main and sub clock.
OSD clock input
OSD clock output
Ground
fsc filter
“L” output when SP mode.
Ground
OSD Video signal input.
5-3
Pin No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Pin Name
WHITE LEVEL
OSD V OUT
OSD Vcc
HLF
V HOLD
C VIDEO IN
NUA
C SYNC
PLL CLK
PLL DATA
PLL ENABLE
TA MUTE
A MUTE
P CONT M12
P CONT SW12
FLD CS
V-SET CS
S OUT0
S IN 0
S CLK 0
I2C CLK
I2C DATA
CBC SIRCS OUT
BUZZER
NICOLE
CAP ERR
DRUM ERR
P FAIL
S REEL
T REEL
DMS+
DMS–
MAIN/SAP
F MONO
STEREO
SAP
CAP FG
AMP Vss
DRUM FG
DRUM PG
AMP Vref OUT
AMP Vref IN
RC CHECK
CTL–IN
CTL+IN
AMP C
CTL AMP OUT
AMP Vcc
A Vcc
V-SET RESET
I/O
I
O
I/O
I/O
I
I
O
O
O
O
O
O
O
O
O
O
I
O
I/O
I/O
O
O
O
O
I
I
I
I
I
O
O
I
I
I
I
I
O
I
I
I/O
I/O
O
O
Function
White level signal input
OSD Video signal output
SW 5V (OSD block)
External low-pass filter for slicer/AFC is connected to this terminal
External capacitor for slicer is connected to this terminal
Control video signal input (osd, tuner, sorvo)
D Ground
Composite sync input
Tuner PLL clock output
Tuner PLL data output
Tuner enable output
Tuner audio mute output
AUDIO mute output
Motor 12V control output
SW 12V control output
FLD drive chip select signal output
V-set micon chip select signal output
Serial communication signal (FLD, V-SET)
Serial communication signal (FLD, V-SET)
Serial communication signal (FLD, V-SET)
IIC clock signal (VIDEO, HiFi)
IIC data signal (VIDEO, HiFi)
Cable mouse sircs signal output
NC
Timing signal output
Capstan error D/A output
Drum error D/A output
Power fail detection input
Supply reel sensor input
Take up reel sensor input
DMS control input
DMS control input
Tuner MAIN/SAP select signal
Tuner audio normal select
Tuner Stereo ditection “L” when Stereo mode.
Tuner SAP ditection “L” when SAP mode.
Capstan FG signal input
Ground
Drum FG input.
Drum PG input.
Analog AMP reference Vcc output
Analog AMP reference Vcc input
Check input
Control signal IN/OUT
Control signal IN/OUT
Control signal AC conect
Control signal AMP output
D-5V
D-5V
NC
5-4E
SLV-662HF/679HF
SECTION 6
ADJUSTMENTS
1-3. Set-up of Adjustment
In this adjustment, NTSC pattern generator is connected with LINE
input terminal. When check to tuner, connected AERIAL terminal.
Check that the synchronizing signal of the Y signal has an amplitude
of approximately 0.7 V and that the burst signal has an amplitude of
approximately 0.3 V and its waveform is flat. And check that the
level ratio of burst signal to “red” signal is 0.30 : 0.66. The video
signal (color bar) used for electrical aligning this unit is shown in
Fig. 6-2-2.
6-1 MECHANICAL ADJUSTMENTS
For the mechanical adjustments, please refer to the
“VHS MECHANICAL ADJUSTMENT MANUAL
(S MECHANISM)” (9-921-647-11).
6-2. ELECTRICAL ADJUSTMENTS
See the adjusting part location diagram from on page 6-6
for the adjustment.
NTSC model
1.
PREPARATION BEFORE ADJUSTMENT
1-1. Equipment Required
The measuring instruments used for this alignment include:
1) Monitor TV
2) Oscilloscope, dual-trace, bandwidth of 30 MHz or more, with
delay mode (A probe 10:1 should be used unless otherwise
specified.)
3) Frequency counter
4) NTSC Pattern generator
5) Remote commander
6) Digital voltmeter
7) Audio generator
8) Audio level meter
9) Audio attenuator
10) Alignment tapes
KRV-51N2 (NTSC) Part No. : 8-192-605-32
About 0.7 V
Red
Horizontal sync signal
1-4. Alignment Tape
• Contents of KRV-51N2
1
2
3
4
VIDEO LINE IN
Video output
(75Ω)
Burst signal
(It must be flat.)
Fig. 6-2-2 Color Bar Signals of Pattern Generator
1-2. Equipment Connection
Unless otherwise specified, connect and adjust the measuring
instruments as shown in the following diagram.
VCR
About
0.3 V
About
0.3 V
Mode
Pattern generator
White (100%)
Monitor TV
VIDEO LINE OUT
Fig. 6-2-1
6-1
SP
LP
Period
Video signal
Audio signal
Normal
Hi-Fi
7 minutes
3 minutes
7 minutes
3 minutes
Color bar
Monoscope
Color bar
Monoscope
400Hz
(L/R)
400Hz
1-5. Input/Output Levels and Impedance
Video input: LINE IN
Input signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
Video output: LINE OUT
Output signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
Audio input: LINE IN
Input level: –7.5 dBs
(0 dBs= 0.775 Vrms)
Input impedance: more than 47 kilohms
Audio output:LINE OUT
Standard level: –7.5 dBs at load impedance 47
kilohms
Output impedance: less than 10 kilohms
2.
POWER SUPPLY CHECK
2-1. Output Voltage Check (MA-341 Board)
Mode
STANDBY
+30 V Check
Measurement point
C627 ‘
Specified value
–11 V Check
31.0 – 39.0 V
Measurement point
Specified value
C642 ’
–12.5 – – 9.5 V
+6 V Check
1-6. Adjustment Sequence
The adjustments should be performed in the following sequence.
Power Supply Check
Servo/Video System Adjustments
Audio System Adjustments
Measurement point
Specified value
Corrector of Q607
5.56 – 6.25 V
Mode
Measuring Instrument
E-E
Digital voltmeter
+12 V Check
Measurement point
IC601 pin 2
Specified value
+5 V Check
11.7 –12.3 V
Measurement point
Specified value
Emitter of Q603
4.8 –5.4 V
MTR12 V Check
Measurement point
Correcter of Q605
Specified value
12.5 –14.5 V
[Check Method]
1) Each of these supply voltages must meet its specified value.
6-2
3.
SERVO SYSTEM CHECK
3-1. RF Switching Position Adjustment
(MA-341 Board)
[Adjustment Purpose]
To adjust the link of the A-ch and B-ch of the tape playback outputs.
To make the unit compatible with other tapes and units. If this
specification is not satisfied, the link will appear on the screen and
the screen will be disrupted, etc.
4.
AUDIO SYSTEM ADJUSTMENT
• Adjust both L ch and R ch.
[Connecting Instruments]
Audio line OUTPUT L/R
Audio line INPUT L/R
Audio oscillator
Mode
Signal
Measurement point
Alignment tape: SP color bar portion
CH1: CN270 pin 2
(PB RF)
CH2: CN270 pin 3 (RF SWP)
Measuring instrument
Adjusting element
Oscilloscope
REMOCON CH+/–
Specified value
A=minimize
47 kΩ
600 Ω
Playback
Audio level meter
or distortion meter
Attenuator
VTR
Fig. 6-2-4
4-1. Hi-Fi Audio System Adjustment
(Hi-Fi model only)
• Perform the adjustment setting the switch on the following
positions.
• AUDIO MONITOR ..................................................... STEREO
[Adjustment Method]
1) Playback the alignment tape.
2) Short JS401 to Ground.
3) Check that “A P” is indicated on FL display.
4) Adjust so that part A becomes minimized at CH +/–.
5) Write data in EEPROM by pressing PAUSE button.
Monoral model:
6) The display “A P” disappears and then the Adjustment mode
terminates.
Hi-Fi model:
6) The display changes to “A H” and the mode goes to the HiFi
switching position Adjustment.
[Adjustment Method]
1. ACE head adjustment.....Refer to the VHS mechanical
adjustment manual (S MECHANISM)(9-921-647-11).
2. E-E output level check
3. “Recording Bias Adjustment”
A
CH1
PB RF
CH2
RF SWP
Fig. 6-2-3
6-3
4-2. HiFi Switching Position Adjustment
(MA-341 Board)
[Adjustment Purpose]
To adjust the link of the A-ch and B-ch of the tape playback outputs.
To make the unit compatible with other tapes and units. If this
specification is not satisfied, the link will appear on the screen and
the screen will be disrupted, etc.
Mode
Playback
Signal
Measurement point
Alignment tape: SP color bar portion
CH1: Pin 1 of CN270 (HF ADJ)
CH2: Pin 3 of CN270 (RF SWP)
Measuring instrument
Adjusting element
Oscilloscope
REMOCON CH +/–
Specified value
B=minimize
4-3. Normal Audio System Adjustment
• Make adjustment in the SP mode unless otherwise specified. Use
a normal VHS cassette for an adjustment tape.
• Set AUDIO MONITOR to normal.
4-3-1. ACE Head Adjustment
Refer to the VHS mechanical adjustment manual
MECHANISM) (9-921-647-11).
(S
4-3-2. E-E Output Level Check
[Adjustment purpose]
Confirm that the output level adjust the reference input is within the
specification.
Mode
E-E
[Adjustment Method]
1) Check that “A H” is indicated on FL display.
2) Adjust so that part B becomes minimized at CH +/–.
3) Write data EEPROM by pressing PAUSE button.
4) Check that “A H” indicator turns off.
5) If “A H” indicator is still on, restart RF switching position
Adjustment from the beginning.
Signal
Measurement point
400 Hz, –7.5 dBs
CJ561 L/R
Measuring instrument
Specified value
Audio level meter
–7.5 ± 2 dBs
[Check Method]
1) Input signal of 400 Hz and –7.5 dBs to the CJ561 L/R.
2) Check that the audio output level is –7.5 ± 2 dBs.
4-3-3. Frequency Response Check
[Adjustment purpose]
Confirm that the frequency characteristic is within the specification.
Mode
REC and PB (SP mode)
B
Signal
CH1
HFADJ
CH2
RF SWP
Measurement point
Measuring instrument
400 Hz, –17.5 dBs
7 kHz, –17.5 dBs
Audio output terminal
Audio level meter
Specified value
0 ± 3 dB
Note: Tape path adjustment must have been completed.
Fig. 6-2-5
[Confirmation Method]
1) Supply a signal of 400 Hz, –17.5 dBs to both L and R channels
of Audio Line Input.
2) Connect the audio level meter to the Audio Line Output.
3) Adjust the attenuator so that the audio level meter will indicate
–17.5 dBs.
4) Make recording in the SP mode.
5) Set an audio line input signal to 7 kHz and make recording.
6) Playback a recorded portion, and measure output levels at 400
Hz and 7 kHz.
7) Confirm that the 7 kHz playback output level within a range of
the 400 Hz playback output level 0 ± 3 dB.
6-4
5.
ADJUSTING PARTS LOCATION DIAGRAM
MA-341 BOARD
(CONDUCTOR SIDE)
CJ561
CN270
4
VIDEO/AUDIO LINE
IN/OUT
1
RF/HF SWP
+
B
E
Q605
MTR12 V
C627
+30 V
Q603
B
E
B
+12 V
4
Q607
1
E
IC601
JS401
+
C642
-11 V
6-6E
SLV-662HF/679HF
SECTION 7
REPAIR PARTS LIST
7-1. EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
•
The mechanical parts with no reference number
in the exploded views are not supplied.
Abbreviation
CND : Canadian
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
7-1-1. FRONT PANEL AND UPPER CASE SECTION
12
9
10
13
9
11
EXCEPT PX MODEL
14
11
6
5
PX MODEL
4
8
7
1
2
Ref. No.
3
Part No.
Description
Ref. No.
Part No.
Description
1
1
2
2
3
X-3949-095-1
X-3949-201-1
3-052-785-01
3-052-785-11
3-052-786-01
PANEL ASSY, FRONT (662)
PANEL ASSY, FRONT (679)
BUTTON (S), CENTER (679)
BUTTON (S), CENTER (662)
RING (S), BUTTON (679)
9
9
10
10
! 11
3-710-901-11
3-710-901-41
3-054-142-01
3-054-142-11
1-782-000-13
SCREW, TAPPING
SCREW, TAPPING
CASE, UPPER (679)
CASE, UPPER (662)
CORD, POWER (679: PX)
3
4
5
6
* 7
3-052-786-11
3-052-779-01
3-052-787-01
3-953-432-01
A-6791-732-A
RING (S), BUTTON (662)
PLATE (NA), FROSTED
PLATE (NA), DOOR ORNAMENTAL
SPRING (GE), FL
DS-84 BOARD, COMPLETE
! 11
! 11
12
13
14
1-782-001-13
1-790-293-21
1-418-153-11
3-709-432-01
3-052-778-31
CORD, POWER (679: PX)
CORD, POWER (EXCEPT PX)
COMMANDER,STANDARD (RMT-V266)
COVER,REMOTE CONTROL BATTERY
DOOR (NA), CASSETTE (679: US)
8
Remarks
4-921-277-41 SCREW (B2.6 × 8), TAPPING, BIND
14
7-1
3-052-778-41 DOOR (NA), CASSETTE (662: US)
Remarks
7-1-2. CHASSIS SECTION
#1
#1
#1
53
53
53
53
52
54
53
51
not supplied
not supplied
Ref. No.
Part No.
Description
Remarks
* 51
* 52
* 52
3-959-383-01 BASE (R), MD
A-6791-731-A MA-341 BOARD, COMPLETE (662)
A-6791-734-A MA-341 BOARD, COMPLETE (679:US,CND)
Ref. No.
Part No.
* 52
53
* 54
A-6791-778-A MA-341 BOARD, COMPLETE (679: PX)
3-970-608-21 SUMITITE (B3), +BV
3-979-652-11 PANEL (M), REAR
7-2
Description
Remarks
7-1-3. MECHANISM DECK SECTION-1
707
#701
710
708
709
706
not
supplied
723
704
712
711
703
705
702
722
701
713
726
724
721
720
701
716
714
719
715
717
718
Ref. No.
Part No.
Description
Remarks
701
702
703
704
705
3-977-509-01
3-977-507-01
3-977-508-01
1-500-144-11
3-977-495-01
WASHER, THRUST
TABLE, REEL (S) (GRAY)
TABLE, REEL (T) (BLACK)
HEAD, FE
SHAFT TG2
706
707
708
709
710
3-977-494-01
A-6759-619-C
3-977-535-01
3-977-536-01
3-970-471-01
HOLDER, FEH
FL COMPLETE ASSY BOARD, COMPLETE
PLATE, LUMINOUS (END SENSOR)
PLATE, LUMINOUS (TOP SENSOR)
SPRING (DECK OPEN), TORSION
711
712
713
A-6759-615-A PRESS BLOCK ASSY, PINCH
3-958-455-01 SPRING (PINCH), TENSION
3-977-447-01 GEAR, ELEVATOR
Ref. No.
7-3
Part No.
Description
714
715
716
717
718
3-977-514-01
3-977-441-01
3-977-445-01
3-977-465-01
X-3947-582-1
OPENER, LID
GEAR, PINCH PRESSING
GEAR, TG8 ARM DRIVING
SPRING, EXTENSION (RVS BRAKE)
ARM ASSY, RVS BRAKE
719
720
721
722
723
3-977-446-01
X-3947-590-1
A-6759-620-A
3-974-556-01
3-979-508-01
GEAR, TG8 ARM
TG8 ASSY
HEAD BLOCK ASSY, ACE (TDK)
+HEXA TT 2.6 × 9 (TAPER)
SCREW +HEXA TP SW 3 × 8
724
726
3-719-381-01 SCREW (M2 × 4)
3-736-045-01 BEARING (NO FLANG), BALL
Remarks
7-1-4. MECHANISM DECK SECTION-2
776
771
772
773
#701
761
#701
767
764
760
763
762
758
759
762
763
757
#702
766
756
765
755
754
752
753
751
Ref. No.
Part No.
Description
751
752
753
754
755
X-3947-581-1
3-977-462-01
X-3947-573-1
X-3947-580-2
3-977-513-02
BRAKE ASSY,MAIN(T)
SPRING,EXTENTION. (MAIN BRAKE)
ARM ASSY, PENDULUM
BRAKE ASSY, MAIN(S)
LEVER, REC PROOF
756
757
758
759
760
3-976-767-01
3-977-487-01
X-3947-587-1
X-3947-589-1
3-977-488-01
SPRING, TENS. (REC. PROOF)
BOSS, TG1 FULCRUM
TG1 ASSY
BAND ASSY, TG1
SPRING (POWER TENSION)
761
A-6750-324-A SHUTTLE (S) BLOCK ASSY
Remarks
Ref. No.
7-4
Part No.
Description
762
763
764
765
766
X-3944-378-1
3-965-178-01
3-969-632-04
A-6750-328-E
3-977-501-01
ROLLER ASSY, GUIDE
SPRING
BASE, DRUM
SHUTTLE (T) BLOCK ASSY
PLATE, LUMINOUS
767
771
772
773
776
X-3943-899-8
A-6746-074-G
X-3947-255-1
3-975-724-07
8-839-057-51
GROUND ASSY, SHAFT
ROLLER BLOCK ASSY, HC
ROLLER ASSY, HC
ARM, HC
DRUM ASSY DZH-0A7A/Z-RP
Remarks
7-1-5. MECHANISM DECK SECTION-3
816
815
817
M902
803
818
803
814
#701
812
813
828
811
829
819
820
810
808
809
827
821
826
807
805
822
804
806
823
824
833
831
832
830
M903
803
801
825
802
835
#703
Ref. No.
Part No.
Description
801
802
803
804
805
3-977-437-01
X-3947-584-1
3-977-443-01
3-977-438-01
3-977-506-01
RETAINER,CAM MOTOR
ASSY, REEL DIRECT
WASHER, STOPPER
WORM - WHEEL
ARM, LIMITTER SELECTION
806
807
808
809
810
3-977-444-01
3-977-515-01
3-977-517-01
3-977-519-01
3-977-518-02
811
812
813
814
815
3-977-516-01
3-977-877-01
3-977-504-01
X-3947-585-1
3-977-510-01
816
817
818
3-977-440-01 WASHER, STOPPER
3-977-439-01 GEAR, CAM
3-977-442-01 SLIDER
Remarks
Ref. No.
Part No.
Description
819
820
821
822
823
3-977-455-01
3-977-456-03
X-3947-579-1
3-977-451-01
3-977-452-01
GEAR, LOADING(T)
SPRING, TORSION (LOAD T)
LEVER ASSY, LOADING(T)
GEAR, LOADING(S)
SPRING, TORSION (LOAD S)
GEAR, PINCH TRANSMISSION
GUIDE, FL SLIDER
PLATE, SLIDE, FL
SPRING, TENS. (LIMIT, FL)
PLATE, LIMITTER, FL
824
825
826
827
828
X-3947-578-1
X-3947-576-2
3-977-468-01
3-977-467-02
X-3947-583-1
LEVER ASSY, LOADING (S)
CHASSIS ASSY, MECHANICAL
SHAFT, CAPSTAN BRAKE
SPRING, CAP BRAKE
BRAKE ASSY, CAPSTAN
HOLDER, FL SLIDER
PLATE, RETAINER
GEAR, CLUTCH
GEAR ASSY, PULLEY
BELT, RUBBER
829
830
831
832
833
3-977-489-01
A-6759-616-A
1-666-524-11
1-766-723-21
3-977-436-01
ARM, TG1 DRIVING
GEAR BLOCK ASSY, LOADING (S)
CA-55 BOARD
CONNECTOR, BOARD TO BOAR 3P
WORM
835
M902
M903
3-989-917-01 SPACER (REC PROOF)
1-698-971-11 MOTOR, DC
X-3947-577-1 MOTOR ASSY, CAM
7-5
Remarks
DS-84
MA-341
7-2. ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•
CAPACITORS:
uF: µF
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
COILS
uH: µH
•
•
When indicating parts by reference number,
please include the board name.
Ref. No.
Part No.
Description
Remarks
Ref. No.
*
A-6791-732-A DS-84 BOARD, COMPLETE
************************
(Ref.No: 2,000 Series)
< JUMPER RESISTOR >
JR441
JR442
1-216-295-00 METAL CHIP
1-216-295-00 METAL CHIP
0
0
5%
5%
1/10W
1/10W
1.5K
1.5K
33
5%
5%
5%
1/10W
1/10W
1/10W
< RESISTOR >
R451
R452
R453
1-216-053-00 METAL CHIP
1-216-053-00 METAL CHIP
1-216-013-00 METAL CHIP
< SWITCH >
S442
1-762-196-21 SWITCH, TACT (PLAY)
S443
1-762-196-21 SWITCH, TACT (STOP)
S444
1-762-196-21 SWITCH, TACT (REW)
S446
1-762-196-21 SWITCH, TACT (FF)
************************************************************
A-6791-731-A MA-341 BOARD, COMPLETE (662)
***********************
*
*
A-6791-734-A MA-341 BOARD, COMPLETE (679: US, CND)
***********************
*
A-6791-778-A MA-341 BOARD, COMPLETE (679: PX)
***********************
(Ref.No: 1,000 Series)
3-951-893-01
3-960-273-01
3-960-274-01
3-966-865-01
3-970-608-21
*
*
*
*
HEAT SINK (EXCEPT PX)
SPACER, TOP END
SPACER, LED
BASE, INDICATION TUBE
SUMITITE (B3), +BV
4-017-441-01 CUSHION (B)
•
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
Part No.
Description
Remarks
C112
C113
C115
C116
C140
1-164-232-11
1-164-004-11
1-164-232-11
1-164-232-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.1uF
0.01uF
0.01uF
100uF
C141
C142
C143
C144
C145
1-163-038-00
1-163-037-11
1-128-131-11
1-128-131-11
1-126-935-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.1uF
0.022uF
22uF
22uF
470uF
C146
C160
C161
C162
C163
1-164-161-11
1-163-809-11
1-163-809-11
1-163-038-00
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.047uF
0.047uF
0.1uF
0.047uF
10%
10%
10%
10%
100V
25V
25V
25V
25V
C164
C165
C166
C167
C168
1-163-237-11
1-163-102-00
1-163-231-11
1-163-233-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
27PF
24PF
15PF
18PF
100uF
5%
5%
5%
5%
20%
50V
50V
50V
50V
10V
C169
C170
C171
C172
C173
1-163-038-00
1-163-007-11
1-104-905-11
1-164-232-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CAPACITOR
CERAMIC CHIP
CERAMIC CHIP
0.1uF
680PF
0.22F
0.01uF
0.01uF
C176
C201
C202
C203
C204
1-164-004-11
1-104-760-11
1-164-232-11
1-164-004-11
1-109-982-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.047uF
0.01uF
0.1uF
1uF
C205
C206
C207
C208
C209
1-164-232-11
1-164-004-11
1-163-241-11
1-164-232-11
1-124-589-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.1uF
39PF
0.01uF
47uF
C210
C211
C213
C214
C215
1-164-004-11
1-163-239-11
1-163-131-00
1-163-257-11
1-163-227-11
CERAMIC CHIP 0.1uF
CERAMIC CHIP 33PF
CERAMIC CHIP 390PF
CERAMIC CHIP 180PF
CERAMIC CHIP 10PF
C216
C217
C218
C220
C221
1-126-160-11
1-163-037-11
1-162-306-11
1-164-232-11
1-109-982-11
ELECT
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
CERAMIC CHIP
20%
50V
25V
50V
50V
10V
10%
20%
20%
20%
25V
25V
50V
50V
6.3V
10%
10%
10%
10%
10%
10%
10%
5%
20%
25V
50V
5.5V
50V
50V
25V
50V
50V
25V
10V
50V
25V
50V
50V
16V
< CAPACITOR >
C101
C102
C103
C104
C105
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-128-057-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001uF
0.001uF
0.001uF
0.001uF
330uF
10%
10%
10%
10%
20%
50V
50V
50V
50V
6.3V
C106
C107
C108
C109
C111
1-124-589-11
1-164-346-11
1-164-004-11
1-164-004-11
1-164-232-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
1uF
0.1uF
0.1uF
0.01uF
20%
16V
16V
25V
25V
50V
10%
10%
7-6
1uF
0.022uF
0.01uF
0.01uF
1uF
10%
25V
5%
50V
5%
50V
5%
50V
0.5PF 50V
20%
10%
20%
10%
50V
25V
16V
50V
10V
MA-341
Ref. No.
Part No.
Description
Part No.
Description
C222
C223
C225
C226
C227
1-124-261-00
1-128-131-11
1-126-160-11
1-164-004-11
1-164-004-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
10uF
22uF
1uF
0.1uF
0.1uF
20%
20%
20%
10%
10%
Remarks
50V
50V
50V
25V
25V
C323
C324
C325
C361
C362
1-163-135-00
1-164-232-11
1-164-232-11
1-126-964-11
1-163-020-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
560PF
5%
0.01uF
0.01uF
10uF
20%
0.0082uF 10%
50V
50V
50V
50V
50V
C228
C229
C230
C231
C232
1-124-589-11
1-164-004-11
1-164-159-21
1-124-589-11
1-109-982-11
ELECT
CERAMIC CHIP
CERAMIC
ELECT
CERAMIC CHIP
47uF
0.1uF
0.1uF
47uF
1uF
20%
10%
16V
25V
50V
16V
10V
C363
C364
C365
C366
C367
1-104-664-11
1-126-964-11
1-126-964-11
1-126-964-11
1-104-664-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
10uF
10uF
10uF
47uF
20%
20%
20%
20%
20%
16V
50V
50V
50V
16V
C233
C234
C235
C236
C237
1-124-261-00
1-109-982-11
1-164-004-11
1-164-232-11
1-164-232-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
1uF
0.1uF
0.01uF
0.01uF
20%
10%
10%
50V
10V
25V
50V
50V
C368
C369
C370
C371
C372
1-163-020-00
1-126-964-11
1-164-232-11
1-164-004-11
1-124-589-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.0082uF
10uF
0.01uF
0.1uF
47uF
10%
20%
50V
50V
50V
25V
16V
C238
C239
C240
C241
C242
1-124-589-11
1-164-232-11
1-124-589-11
1-164-232-11
1-164-232-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
47uF
0.01uF
47uF
0.01uF
0.01uF
20%
16V
50V
16V
50V
50V
C373
C374
C375
C376
C381
1-124-589-11
1-163-038-00
1-164-232-11
1-126-964-11
1-164-222-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
47uF
0.1uF
0.01uF
10uF
0.22uF
20%
C243
C244
C245
C246
C247
1-164-232-11
1-109-982-11
1-109-982-11
1-164-232-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
1uF
1uF
0.01uF
0.022uF
10%
50V
10V
10V
50V
25V
C382
C383
C384
C385
C386
1-164-222-11
1-126-960-11
1-126-960-11
1-126-960-11
1-126-964-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.22uF
1uF
1uF
1uF
10uF
20%
20%
20%
20%
25V
50V
50V
50V
50V
C248
C249
C250
C251
C267
1-163-809-11
1-109-982-11
1-163-809-11
1-164-004-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
1uF
0.047uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
25V
10V
25V
25V
25V
C387
C388
C389
C390
C391
1-126-964-11
1-126-964-11
1-126-964-11
1-126-960-11
1-126-160-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
10uF
10uF
1uF
1uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C271
C272
C275
C276
C278
1-164-232-11
1-164-004-11
1-164-232-11
1-164-004-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.01uF
0.1uF
0.022uF
50V
25V
50V
25V
25V
C405
C422
C423
C424
C425
1-164-232-11
1-124-589-11
1-164-232-11
1-164-159-21
1-124-261-00
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC
ELECT
0.01uF
47uF
0.01uF
0.1uF
10uF
C279
C280
C281
C282
C283
1-164-004-11
1-124-584-00
1-164-232-11
1-164-232-11
1-164-232-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.01uF
0.01uF
0.01uF
10%
20%
25V
10V
50V
50V
50V
C427
C500
C501
C502
C503
1-164-004-11
1-163-098-00
1-163-098-00
1-164-232-11
1-163-017-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
16PF
16PF
0.01uF
0.0047uF
10%
5%
5%
5%
25V
50V
50V
50V
50V
C284
C285
C286
C301
C303
1-164-489-11
1-164-232-11
1-163-251-11
1-163-038-00
1-126-160-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.22uF
0.01uF
100PF
0.1uF
1uF
10%
20%
16V
50V
50V
25V
50V
C504
C505
C507
C508
C509
1-163-275-11
1-162-199-31
1-163-137-00
1-109-982-11
1-163-016-00
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
10PF
680PF
1uF
0.0039uF
5%
5%
5%
10%
10%
50V
50V
50V
10V
50V
C305
C307
C308
C310
C311
1-124-261-00
1-126-966-11
1-126-963-11
1-126-160-11
1-163-014-00
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
10uF
33uF
4.7uF
1uF
0.0027uF
20%
20%
20%
20%
10%
50V
16V
50V
50V
50V
C510
C511
C512
C513
C514
1-164-004-11
1-163-038-00
1-124-584-00
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
100uF
0.001uF
0.001uF
10%
25V
25V
10V
50V
50V
C312
C313
C314
C315
C316
1-163-016-00
1-164-232-11
1-126-964-11
1-126-160-11
1-163-024-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.0039uF
0.01uF
10uF
1uF
0.018uF
10%
50V
50V
50V
50V
50V
C561
C562
C563
C600
! C601
1-164-232-11
1-104-664-11
1-126-935-11
1-104-705-11
1-113-920-11
CERAMIC CHIP
ELECT
ELECT
FILM
CERAMIC
0.01uF
47uF
470uF
0.1uF
0.0022uF
C317
C318
C319
C320
C322
1-124-589-11
1-164-232-11
1-164-232-11
1-137-374-11
1-126-963-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
47uF
0.01uF
0.01uF
0.047uF
4.7uF
20%
10%
20%
10%
10%
10%
10%
10%
5%
20%
20%
10%
20%
5%
20%
Ref. No.
16V
50V
50V
50V
50V
7-7
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Remarks
10%
20%
20%
20%
20%
20%
10%
10%
20%
20%
20%
20%
16V
25V
50V
50V
25V
50V
16V
50V
50V
50V
50V
16V
6.3V
250V
250V
(EXCEPT PX)
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-341
Ref. No.
Part No.
! C601
1-104-705-11 FILM
0.1uF
! C602
! C603
1-119-892-51 CERAMIC
1-113-900-11 CERAMIC
470PF
470PF
! C603
1-119-911-51 CERAMIC
470PF
! C604
1-113-900-11 CERAMIC
470PF
! C604
Description
1-119-912-51 CERAMIC
1000PF
C605
1-127-932-41 ELECT
150uF
C605
1-119-882-51 ELECT(BLOCK)
120uF
C606
1-107-905-11 ELECT
4.7uF
C606
1-107-925-11 ELECT
1uF
C607
1-113-681-11 FILM
0.033uF
C607
1-136-203-11 FILM
C608
1-162-558-11 CERAMIC
C609
1-107-974-11 CERAMIC
C610
1-104-683-11 MYLAR
Remarks
Ref. No.
250V
(PX)
10%
250V
10%
250V
(PX)
10%
250V
(EXCEPT PX)
10%
250V
(PX)
C639
1-164-232-11 CERAMIC CHIP
C642
1-126-967-11 ELECT
C701
C706
C707
1-104-664-11 ELECT
1-126-963-11 ELECT
1-164-161-11 CERAMIC CHIP
50V
(EXCEPT PX)
47uF
20%
50V
(EXCEPT PX)
47uF
20%
16V
4.7uF
20%
50V
0.0022uF 10%
100V
C709
C710
C712
1-126-933-11 ELECT
1-164-232-11 CERAMIC CHIP
1-126-933-11 ELECT
100uF
0.01uF
100uF
20%
20%
250V
(EXCEPT PX)
20%
400V
(PX)
20%
200V
(EXCEPT PX)
20%
50V
(EXCEPT PX)
20%
100V
(PX)
10%
400V
(EXCEPT PX)
0.01uF
10%
400V
(PX)
100PF
10%
2KV
(EXCEPT PX)
47PF
5%
2KV
(PX)
0.0047uF 5%
50V
(PX)
C610
1-115-322-91 FILM
0.047uF
C611
1-115-322-91 FILM
0.047uF
C611
1-136-160-00 FILM
0.039uF
C612
C613
1-126-160-11 ELECT
1-115-739-31 ELECT
1uF
0.0015F
50V
(EXCEPT PX)
5%
50V
(EXCEPT PX)
5%
50V
(PX)
20%
50V
20%
10V
C614
C615
C616
C617
C618
1-115-789-11
1-126-967-11
1-126-941-11
1-126-935-11
1-126-934-11
0.001F
47uF
470uF
470uF
220uF
20%
20%
20%
20%
20%
ELECT
ELECT
ELECT
ELECT
ELECT
Part No.
CJ561
C619
C620
C621
C622
1-164-232-11
1-164-232-11
1-164-232-11
1-128-131-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.01uF
0.01uF
22uF
50V
(EXCEPT PX)
50V
50V
50V
20%
50V
C623
C624
C625
C626
C627
1-124-589-11
1-124-589-11
1-104-664-11
1-126-965-11
1-126-965-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
47uF
47uF
22uF
22uF
20%
20%
20%
20%
20%
16V
16V
16V
50V
50V
C628
C629
C631
1-164-232-11 CERAMIC CHIP
1-124-234-00 ELECT
1-163-259-91 CERAMIC CHIP
0.01uF
22uF
220PF
20%
5%
50V
16V
50V
C638
1-128-551-11 ELECT
22uF
20%
25V
C638
1-126-925-11 ELECT
470uF
20%
(PX)
10V
(EXCEPT PX)
20%
16V
50V
16V
1-779-011-11 JACK, PIN 6P (LINE OUT/LINE-1 IN)
CN101
CN102
* CN103
CN104
CN161
1-779-724-11
1-779-723-11
1-766-716-11
1-506-469-11
1-506-468-11
CONNECTOR, BOARD TO BOARD 5P
CONNECTOR, BOARD TO BOARD 9P
CONNECTOR, BOARD TO BOARD 3P
PIN, CONNECTOR 4P
PIN, CONNECTOR 3P
CN260
* CN270
CN301
CN302
CN404
1-766-986-11
1-560-892-00
1-506-469-11
1-506-468-11
1-506-469-11
CONNECTOR, FFC/FPC 13P
PIN, CONNECTOR 4P
PIN, CONNECTOR 4P
PIN, CONNECTOR 3P
PIN, CONNECTOR 4P
* CN600
1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
(PX)
47uF
20%
< CONNECTOR >
25V
50V
25V
16V
16V
1-126-967-11 ELECT
Remarks
0.01uF
< JACK >
5%
C618
Description
20%
(PX)
7-8
< DIODE >
D103
D109
D161
D162
D405
8-719-048-26
8-719-200-82
8-719-200-82
8-719-200-82
8-719-056-07
DIODE
DIODE
DIODE
DIODE
DIODE
GL528V1
11ES2
11ES2
11ES2
SLR-342MC3F (POWER)
D420
D561
D600
D601
D602
8-719-109-90
8-719-110-08
8-719-051-93
8-719-054-32
8-719-058-91
DIODE
DIODE
DIODE
DIODE
DIODE
RD5.6ESB3
RD8.2ES-B2
DF06M-6031
ERA15-06TP3
AG01A-V0 (EXCEPT PX)
D602
D603
D604
D604
D605
8-719-030-25
8-719-200-82
8-719-109-59
8-719-109-62
8-719-911-19
DIODE
DIODE
DIODE
DIODE
DIODE
EG01C-V0 (PX)
11ES2 (EXCEPT PX)
RD2.7ES-B1 (PX)
RD3.0ES-B1 (EXCEPT PX)
1SS119
D606
D607
D608
D609
D610
8-719-313-17
8-719-022-97
8-719-073-18
8-719-313-17
8-719-160-64
DIODE
DIODE
DIODE
DIODE
DIODE
AU02A-V0
D2S4MF
S3L20UF34
AU02A-V0
RD16F-B1
D611
D612
D614
D615
D616
8-719-911-19
8-719-109-85
8-719-911-19
8-719-109-89
8-719-110-47
DIODE
DIODE
DIODE
DIODE
DIODE
1SS119
RD5.1ES-B2
1SS119 (PX)
RD5.6ESB2 (PX)
RD18ES-T1B (PX)
D617
D618
D619
D702
8-719-911-19
8-719-911-19
8-719-313-17
8-719-150-92
DIODE
DIODE
DIODE
DIODE
1SS119 (PX)
1SS119
AU02A-V0 (EXCEPT PX)
RD33EB3T
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-341
Ref. No.
Part No.
Description
Remarks
Ref. No.
< EARTH >
ET600
ET601
1-537-770-21 TERMINAL BOARD, GROUND
1-537-770-21 TERMINAL BOARD, GROUND
Part No.
Description
JR128
JR131
JR132
JR133
JR134
1-216-295-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/8W
1/10W
Remarks
JR135
JR136
JR137
JR139
JR140
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/8W
1/10W
JR141
JR142
JR143
JR144
JR145
1-216-295-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/8W
1/8W
JR146
JR147
JR148
JR149
JR150
1-216-296-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/10W
1/8W
1/8W
1/8W
JR152
JR153
JR154
JR155
JR156
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/8W
1/10W
JR157
JR158
JR159
JR160
JR161
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
JR162
JR163
JR164
JR166
JR169
1-216-296-00
1-216-295-00
1-216-295-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/8W
1/8W
JR170
JR172
JR173
JR174
JR175
1-216-296-00
1-216-296-00
1-216-295-00
1-216-296-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/10W
1/8W
1/10W
JR176
JR180
JR181
JR182
JR183
1-216-296-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
JR184
JR190
JR197
JR198
JR199
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/8W
1/8W
1/8W
1/10W
JR200
JR201
JR202
1-216-295-00 METAL CHIP
1-216-296-00 METAL CHIP
1-216-295-00 METAL CHIP
0
0
0
5%
5%
5%
1/10W
1/8W
1/10W
< FUSE >
! F600
! F600
1-532-388-31 FUSE (PX)
1-533-296-11 FUSE, GLASS CYLINDRICAL (DIA.5)
(EXCEPT PX)
< FERRITE BEAD >
FB101
FB601
1-414-235-22 INDUCTOR CHIP 0UH
1-410-858-21 INDUCTOR
0UH
< FUSE HOLDER >
FH600
FH601
1-533-399-31 HOLDER, FUSE
1-533-399-31 HOLDER, FUSE
< IC >
IC101
IC160
IC161
IC161
IC162
8-759-481-46
8-759-580-37
8-759-518-23
8-759-575-71
8-759-248-87
IC
IC
IC
IC
IC
LB1943
M37760M8A120GP
X24C04S8
M24C04-WMN6T
MM1256XF-BE
IC201
IC260
IC331
IC360
IC403
8-759-564-37
8-759-564-36
8-759-499-30
8-759-559-37
8-742-042-00
IC
IC
IC
IC
HY
LA71050M-MPB
LA70011
BA7755AF-E2
TDA9605H/N1,557
B IC SBX1986-51
IC420
IC601
IC602
8-759-438-82 IC uPD16311GC-AB6
8-759-438-18 IC PQ12RD08
8-759-321-95 IC HA17431PA-TZ
< JUMPER RESISTOR >
JR045
JR046
JR047
JR048
JR100
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/8W
JR101
JR102
JR104
JR105
JR107
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/10W
1/10W
JR109
JR113
JR114
JR115
JR116
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/10W
1/8W
JR117
JR118
JR119
JR120
JR121
1-216-295-00
1-216-295-00
1-216-296-00
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/8W
JR123
JR124
JR125
JR126
JR127
1-216-295-00
1-216-295-00
1-216-296-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/10W
7-9
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-341
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
< METAL CHIP >
1-216-296-00 METAL CHIP
0
5%
JS364
JS412
JS414
JS612
1-216-296-00
1-216-295-00
1-216-295-00
1-216-295-00
0
0
0
0
5%
5%
5%
5%
1/8W
(EXCEPT PX)
1/8W
1/10W
1/10W
1/10W
(PX)
JS614
1-216-295-00 METAL CHIP
0
5%
JS615
JS616
JS617
JS618
1-216-295-00
1-216-296-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
5%
5%
5%
5%
1/10W
1/8W
1/10W
1/10W
(EXCEPT PX)
JS619
1-216-295-00 METAL CHIP
0
5%
JS620
1-216-295-00 METAL CHIP
0
5%
JS621
1-216-295-00 METAL CHIP
0
5%
JS622
1-216-295-00 METAL CHIP
0
5%
JS623
1-216-295-00 METAL CHIP
0
5%
1/10W
(PX)
1/10W
(PX)
1/10W
(PX)
1/10W
(EXCEPT PX)
1/10W
(PX)
JS624
1-216-295-00 METAL CHIP
0
5%
! LF600
1-217-666-11 SHORT
ND420
PH101
PH102
PH600
PH600
1-414-930-21
1-414-936-21
1-414-936-21
1-414-936-21
1-414-946-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
2.2uH
22uH
22uH
22uH
39uH
L202
L203
L204
L205
L206
1-414-940-21
1-414-934-21
1-414-940-21
1-414-940-21
1-414-940-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100uH
10uH
100uH
100uH
100uH
L270
L304
L328
L360
L420
1-414-940-21
1-414-940-21
1-410-071-11
1-414-940-21
1-414-936-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100uH
100uH
10mH
100uH
22uH
L500
L501
L561
L601
L602
1-414-930-21
1-414-940-21
1-414-940-21
1-403-588-11
1-403-588-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
2.2uH
100uH
100uH
22uH
22uH
L603
L603
L604
L605
L606
1-410-509-11
1-410-526-11
1-410-519-11
1-414-142-11
1-414-142-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH (EXCEPT PX)
10uH (PX)
68uH
1uH (EXCEPT PX)
1uH (EXCEPT PX)
L703
L704
1-414-930-21 INDUCTOR
1-414-936-21 INDUCTOR
8-749-013-23
8-749-013-23
8-749-010-64
8-749-014-24
PHOTO INTERRUPTER GP3S120
PHOTO INTERRUPTER GP3S120
PHOTO COUPLER PC123F2 (PX)
COUPLER, PHOTO ON3131-S(LF) (EXCEPT PX)
< IC LINK >
! PS101
! PS600
1/10W
(PX)
1/6W
< COIL >
L101
L161
L162
L163
L201
1-517-732-11 TUBE, FLUORESCENT INDICATOR
< PHOTO INTERUPTER >
1/10W
0.01
1-416-929-11 FILTER, LINE
< FLUORECENT INDICATOR >
< JUMPER RESISTOR >
JW193
Remarks
< LINE FILTER >
JS363
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
Description
1-532-727-11 LINK, IC
1-532-841-21 LINK, IC
0.25A
< TRANSISTOR >
Q101
Q102
Q103
Q201
Q202
8-729-043-84
8-729-043-84
8-729-281-53
8-729-230-49
8-729-230-49
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
PT380F3
PT380F3
2SC1815-GR
2SC2712-YG
2SC2712-YG
Q203
Q302
Q303
Q380
Q381
8-729-216-21
8-729-804-41
8-729-821-15
8-729-216-21
8-729-230-49
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1162-Y
2SB1122-S
2SD1620
2SA1162-Y
2SC2712-YG
Q382
Q401
Q500
Q502
Q561
8-729-230-49
8-729-421-22
8-729-010-05
8-729-216-21
8-729-010-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2712-YG
UN2211
MSB709-RT1
2SA1162-Y
MSB709-RT1
Q601
Q601
Q602
Q603
Q604
8-729-043-47
8-729-904-98
8-729-012-31
8-729-119-78
8-729-010-25
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SK2671 (PX)
2SC4054P (EXCEPT PX)
2SC4040-TL2-Q
2SC403SP-51
MSD601-RT1
Q605
Q606
Q607
Q608
8-729-047-92
8-729-230-49
8-729-140-98
8-729-106-68
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1398-Q(TA).S0
2SC2712-YG (PX)
2SD773-34
2SD1615A-GP
< RESISTOR >
2.2uH
22uH
7-10
R101
R102
R103
R104
R105
1-249-413-11
1-216-089-00
1-249-437-11
1-216-081-00
1-247-863-91
CARBON
METAL CHIP
CARBON
METAL CHIP
CARBON
470
47K
47K
22K
22K
5%
5%
5%
5%
5%
1/4W F
1/10W
1/4W
1/10W
1/4W
R106
R107
R109
R110
R111
1-249-400-11
1-249-400-11
1-216-089-00
1-216-089-00
1-216-057-00
CARBON
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
39
39
47K
47K
2.2K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/10W
1/10W
1/10W
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-341
Ref. No.
Part No.
Description
Part No.
Description
R112
R115
R116
R117
R118
1-216-065-00
1-216-089-00
1-216-089-00
1-216-041-00
1-216-089-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
47K
470
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remarks
Ref. No.
R224
R225
R231
R232
R267
1-216-089-00
1-216-295-00
1-216-089-00
1-216-089-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
0
47K
47K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R119
R120
R121
R142
R143
1-216-077-00
1-249-417-11
1-216-041-00
1-216-051-00
1-216-065-00
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
15K
1K
470
1.2K
4.7K
5%
5%
5%
5%
5%
1/10W
1/4W F
1/10W
1/10W
1/10W
R270
R271
R272
R273
R274
1-216-041-00
1-216-041-00
1-208-788-11
1-216-295-00
1-216-063-91
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
470
470
1.8K
0
3.9K
5%
5%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R159
R160
R161
R162
1-216-097-91
1-216-049-00
1-216-073-00
1-249-419-11
RES,CHIP
METAL CHIP
METAL CHIP
CARBON
100K
1K
10K
1.5K
5%
5%
5%
5%
R276
R277
R278
R279
R301
1-216-069-00
1-216-081-00
1-216-081-00
1-216-081-00
1-216-067-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.8K
22K
22K
22K
5.6K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R163
1-216-049-00 METAL CHIP
1K
5%
1/10W
1/10W
1/10W
1/4W F
(679)
1/10W
R164
R165
R166
R167
R168
1-216-089-00
1-216-089-00
1-216-073-00
1-249-431-11
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
47K
47K
10K
15K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/10W
R302
R305
R309
R310
R311
1-216-093-91
1-216-129-00
1-216-043-91
1-216-071-00
1-216-061-00
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
68K
2.2M
560
8.2K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R169
R170
R171
R172
R174
1-216-073-00
1-216-061-00
1-216-089-00
1-216-073-00
1-216-039-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
3.3K
47K
10K
390
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R312
R313
R314
R315
R316
1-216-057-00
1-216-051-00
1-216-073-00
1-216-035-00
1-216-109-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
1.2K
10K
270
330K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R175
R176
R177
R178
R179
1-216-041-00
1-216-041-00
1-216-041-00
1-216-105-91
1-216-113-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
470
470
470
220K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R317
R318
R319
R320
R321
1-216-071-00
1-216-065-00
1-216-033-00
1-217-671-11
1-216-063-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
8.2K
4.7K
220
1
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R180
R183
R184
R185
R187
1-216-061-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R322
R323
R324
R325
R326
1-216-017-91
1-216-081-00
1-216-031-00
1-216-075-00
1-216-079-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
22K
180
12K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R188
R189
R191
R192
R193
1-216-069-00
1-216-061-00
1-249-417-11
1-249-417-11
1-216-295-00
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
6.8K
3.3K
1K
1K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W F
1/4W F
1/10W
R327
R361
R362
R363
R364
1-216-033-00
1-216-083-00
1-216-057-00
1-208-820-11
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
220
27K
2.2K
39K
2.2K
5%
5%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R194
R196
R201
R202
R203
1-216-073-00
1-216-295-00
1-216-037-00
1-216-047-91
1-216-037-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
10K
0
330
820
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R365
R366
R368
R369
R370
1-216-083-00
1-216-041-00
1-216-079-00
1-216-133-00
1-216-049-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
27K
470
18K
3.3M
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R204
R205
R208
R209
R210
1-216-061-00
1-208-830-11
1-216-295-00
1-216-055-00
1-249-419-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
CARBON
3.3K
100K
0
1.8K
1.5K
5%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W F
R371
R372
R373
R374
R375
1-216-049-00
1-216-073-00
1-216-295-00
1-216-295-00
1-216-025-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
1K
10K
0
0
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R211
R212
R213
R214
R215
1-216-065-00
1-216-043-91
1-216-049-00
1-216-055-00
1-216-071-00
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
560
1K
1.8K
8.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R376
R377
R378
R380
R381
1-216-025-91
1-216-295-00
1-216-295-00
1-216-073-00
1-216-061-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
0
0
10K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R216
R218
R219
R220
R221
1-216-055-00
1-216-295-00
1-216-025-91
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
1.8K
0
100
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R382
R383
R385
R386
R401
1-216-049-00
1-216-049-00
1-216-295-00
1-216-295-00
1-216-029-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
0
0
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
7-11
Remarks
MA-341
Ref. No.
Part No.
Description
R402
R409
R414
R415
R417
1-216-089-00
1-216-013-00
1-216-053-00
1-216-053-00
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
33
1.5K
1.5K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remarks
R418
R419
R420
R421
R422
1-216-057-00
1-216-059-00
1-216-059-00
1-216-295-00
1-216-049-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.7K
2.7K
0
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R423
R424
R425
R426
R427
1-216-049-00
1-216-049-00
1-216-085-00
1-216-065-00
1-216-053-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
33K
4.7K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R440
R441
R442
R500
R502
1-216-075-00
1-216-075-00
1-216-077-00
1-216-049-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
12K
12K
15K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R503
R504
R505
R507
R508
1-216-049-00
1-216-049-00
1-216-045-00
1-216-041-00
1-216-053-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
680
470
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R509
R512
R513
R561
R562
1-216-121-91
1-216-295-00
1-216-041-00
1-216-037-00
1-249-407-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
1M
0
470
330
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W F
R563
R564
R565
! R600
1-249-408-11
1-216-021-00
1-216-022-00
1-219-779-51
CARBON
METAL CHIP
METAL CHIP
CARBON
180
68
75
6.8M
5%
5%
5%
10%
R601
1-249-441-11 CARBON
100K
1/4W F
1/10W
1/10W
1/2W
(EXCEPT PX)
5%
1/4W
R602
1-249-441-11 CARBON
100K
5%
R602
1-247-883-00 CARBON
150K
5%
R606
1-249-415-11 CARBON
680
5%
R603
1-249-439-11 CARBON
68K
5%
R603
1-249-429-11 CARBON
10K
5%
R604
1-215-889-00 METAL OXIDE
330
5%
R604
1-216-451-11 METAL OXIDE
120
5%
R605
1-215-416-00 METAL
620
1%
R605
1-249-411-11 CARBON
330
5%
R606
1-249-402-11 CARBON
56
5%
R607
R608
R609
R610
R611
1-215-927-41
1-249-401-11
1-249-406-11
1-208-789-11
1-216-655-11
47K
47
120
2K
1.5K
5%
5%
5%
0.50%
0.5%
METAL OXIDE
CARBON
CARBON
RES,CHIP
METAL CHIP
1/4W
(EXCEPT PX)
1/4W
(PX)
1/4W F
(PX)
1/4W
(PX)
1/4W
(EXCEPT PX)
F
(PX)
2W
F
(EXCEPT PX)
1/4W
(EXCEPT PX)
1/4W
(PX)
1/4W F
(EXCEPT PX)
Ref. No.
Description
Remarks
1-219-786-81 FUSIBLE
22
5%
R613
! R614
1-260-091-11 CARBON
1-219-153-11 FUSIBLE
220
10
5%
5%
! R614
1-240-306-81 FUSIBLE
15
5%
R615
1-249-417-11 CARBON
1K
5%
1/4W
(EXCEPT PX)
1/2W
1/4W F
(PX)
1/4W
(EXCEPT PX)
1/4W F
R616
R617
R618
R619
R620
1-247-815-91
1-249-417-11
1-260-091-11
1-249-413-11
1-249-413-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
1K
220
470
470
5%
5%
5%
5%
5%
1/4W
1/4W F
1/2W
1/4W F
1/4W F
R623
R624
R625
! R626
1-216-061-00
1-216-430-11
1-249-429-11
1-260-364-11
METAL CHIP
METAL OXIDE
CARBON
CARBON
3.3K
390
10K
1M
5%
5%
5%
5%
1/10W
1W
F
1/4W
1/2W
(PX)
1/4W
(PX)
R627
1-249-441-11 CARBON
100K
5%
R628
1-216-093-91 RES,CHIP
68K
5%
R629
1-216-341-11 METAL OXIDE
0.22
5%
R630
R633
1-216-049-00 METAL CHIP
1-216-295-00 METAL CHIP
1K
0
5%
5%
R633
1-216-047-91 RES,CHIP
820
5%
R634
1-216-073-00 METAL CHIP
10K
5%
R635
1-216-017-91 RES,CHIP
47
5%
R636
1-216-047-91 RES,CHIP
820
5%
R637
1-247-815-91 CARBON
220
5%
! R641
1-219-123-11 FUSIBLE
0.47
5%
1/4W F
(EXCEPT PX)
! R642
1-216-374-41 METAL OXIDE
2.7
5%
! R642
1-215-907-11 METAL OXIDE
22
5%
R643
R645
1-216-061-00 METAL CHIP
1-260-073-11 CARBON
3.3K
5.6
5%
5%
R646
1-260-073-11 CARBON
5.6
5%
2W
(EXCEPT PX)
3W
F
(PX)
1/10W
1/2W
(PX)
1/2W
(PX)
R647
1-215-857-11 METAL OXIDE
10
5%
R701
R702
R703
R704
1-216-049-00
1-216-061-00
1-216-039-00
1-216-043-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
1K
3.3K
390
560
5%
5%
5%
5%
F
(PX)
1/10W
1/10W
1/10W
1/10W
! R705
R706
R707
R709
R710
1-240-307-81
1-216-113-00
1-216-065-00
1-216-061-00
1-216-061-00
FUSIBLE
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
560
470K
4.7K
3.3K
3.3K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
2W
3W
1/4W F
1/4W F
1/10W
1/10W
Part No.
R612
7-12
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
1/10W
(PX)
1W
F
(PX)
1/10W
1/10W
(EXCEPT PX)
1/10W
(PX)
1/10W
(PX)
1/10W
(PX)
1/10W
(PX)
1/4W
1W
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-341
Ref. No.
Part No.
Description
R711
R712
R713
R731
R732
1-216-061-00
1-216-295-00
1-216-295-00
1-216-049-00
1-216-049-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
0
0
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remarks
R733
R734
R735
R736
R737
1-216-065-00
1-216-049-00
1-216-049-00
1-216-295-00
1-216-081-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
1K
1K
0
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R738
1-216-081-00 METAL CHIP
22K
5%
1/10W
< SWITCH >
S101
S102
S401
S402
S403
1-762-108-11
1-771-155-11
1-771-574-21
1-771-574-21
1-771-574-21
SWITCH, PUSH (1 KEY)
SWITCH, ROTARY
SWITCH, TACTILE (EJECT)
SWITCH, TACTILE (POWER)
SWITCH, TACTILE (CHANNEL–)
S406
S410
S421
S431
S701
1-771-574-21
1-771-574-21
1-771-574-21
1-771-574-21
1-571-588-11
SWITCH, TACTILE (EASY SET UP)
SWITCH, TACTILE (PAUSE)
SWITCH, TACTILE (CHANNEL+)
SWITCH, TACTILE (REC)
SWITCH, SLIDE
Ref. No.
Part No.
Description
Remarks
MISCELLANEOUS
***************
! 11
! 11
! 11
12
1-779-725-11
1-782-000-13
1-782-001-13
1-790-293-21
1-418-153-11
CONNECTOR, BOARD TO BOARD 5P
CORD, POWER (PX)
CORD, POWER (PX)
CORD, POWER (EXCEPT PX)
COMMANDER,STANDARD (RMT-V266)
704
1-500-144-11 HEAD, FE
776
8-839-057-51 DRUM ASSY DZH-0A 7A/Z-RP
832
1-766-723-21 CONNECTOR, BOARD TO BOAR 3P
M902
1-698-971-11 MOTOR, DC
M903
X-3947-577-1 MOTOR ASSY, CAM
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
3-961-581-01
3-979-710-01
1-575-334-11
1-696-592-11
3-865-038-11
*
*
SHEET, PROTECTION
SPACER
CORD, CONNECTION
CORD, CONNECTION (NTSC)
MANUAL, INSTRUCTION (ENGLISH)
3-865-038-21 MANUAL, INSTRUCTION
(FRENCH/CHINESE)(CND)
************************************************************
< TRANSFORMER >
!T301 1-433-479-11 TRANSFORMER, BIAS OSCILLATION
!T600 1-431-694-11 TRANSFORMER, CONVERTER (RCC) (PX)
!T600 1-433-568-11 TRANSFORMER, CONVERTER (RCC)
(EXCEPT PX)
< TUNER >
TU701
**************
HARDWARE LIST
**************
#1
#701
#702
#703
7-685-648-79
7-685-646-79
7-682-147-01
7-685-133-19
SCREW +BVTP 3 × 12 TYPE2 IT-3
SCREW +BVTP 3 × 8 TYPE2 IT-3
SCREW +P 3 × 6
SCREW (DIA. 2.6) (IT3B)
8-598-473-00 TUNER, FSS BTF-MA431 (VHF/UHF)
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
< VARISTOR >
! VDR600 1-801-267-31 VARISTOR TNR10V431K660 (PX)
! VDR600 1-801-445-31 VARISTOR TNR10V241K660 (EXCEPT PX)
< VIBRATOR >
X160
1-767-857-11 VIBRATOR, CRYSTAL (14.31818MHz)
X161
1-579-463-11 VIBRATOR, CRYSTAL (32.768kHz)
X201
1-577-380-11 VIBRATOR, CRYSTAL (3.579545MHz)
************************************************************
7-13E
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
SLV-662HF/679HF
Sony Corporation
9-921-709-11
Home A&V Products Company
— 92 —
99A1630-1
Printed in Japan ©1999.1
Published by Quality Assurance Dept.
(Shinagawa)

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Download SLV-662HF/679HF