Download SERVICE MANUAL

SLV-LX40/LX50/LX60S/LX70S
RMT-V293A/V294A
SERVICE MANUAL
Chilean Model
SLV-LX50CL/LX50CS/LX70SCL/
LX70SCS
Mexican Model
SLV-LX40MX/LX50MX/LX60SMX/
LX70SMX
1
4
7
2
3
5
6
8
9
Panama Model
Venezuelan Model
0
SLV-LX50PA/LX50PC/LX50VZ/
LX70SPA/LX70SPC/LX70SVZ
g
S MECHANISM
SLV-LX70S
Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENT for MECHANICAL ADJUSTMENTS.
(9-921-748-11)
HiFi model : SLV-LX60S/LX70S
Mono model: SLV-LX40/LX50
SPECIFICATIONS
System
Format
VHS NTSC standard
Video recording system
Rotary head helical scanning FM system
Video heads
Double azimuth four heads
Video signal
16 W
LINE OUT
(SLV-LX50 (CL/CS/MX/PA/PC/VZ) and
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
AUDIO OUT, phono jacks (1 each) (SLV-LX50
and LX40), (2 each) (SLV-LX70S and LX60S)
Standard output: 327 mVrms
SP: 33.35 mm/s
EP: 11.11 mm/s
LP: 16.67 mm/s,
playback only
Maximum recording/playback time
9 hrs. in EP mode (with T-180 tape)
Fast-forward and rewind time
Approx. 3 min. (with T-120 tape)
Tuner section
Channel coverage
VHF 2 to 13
UHF 14 to 69
CATV A-8 to A-1, A to W, W+1 to W+84
Antenna
75-ohm antenna terminal for VHF/UHF
Output impedance: less than 10 kilohms
LINE-1 IN and -2 IN
VIDEO IN, phono jack (1 each)
Dimensions
Approx. 355 x 96 x 288.8 mm (w/h/d)
including projecting parts and controls
Timer section
Clock
Quartz locked
Timer indication
12-hour cycle
Timer setting
8 programs (max.)
Power back-up
Built-in self-charging capacitor
Back-up duration: up to 8 hours at a time
General
Power requirements
110 V AC to 240 V AC, 50/60 Hz
(SLV-LX70S (CL/CS) and LX50 (CL/CS))
120 V AC, 60 Hz
(SLV-LX70S (MX/PA/PC/VZ), LX60S (MX),
LX50 (MX/PA/PC/VZ), and LX40 (MX))
Power consumption
Input and outputs
5°C to 40°C (41°F to 104°F)
Storage temperature
–20°C to 60°C (–4°F to 140°F)
Load impedance: 47 kilohms
NTSC color, EIA standards
Tape speed
SLV-LX40 (MX))
Operating temperature
Mass
Approx. 3.6 kg
Supplied accessories
Remote commander (1)
Size AA (R6) batteries (2)
75-ohm coaxial cable with F-type connectors (1)
Audio/video cable (1) (3-phono to 3-phono)
(SLV-LX70S and LX60S only)
Plug adaptor (1)
(SLV-LX70S (CL/CS) and LX50 (CL/CS) only)
Design and specifications are subject to change
without notice
ENERGY STAR® is a U.S. registered mark.
As an ENERGY STAR® Partner, Sony Corporation
has determined that this product meets the
ENERGY STAR®
17 W
(SLV-LX70S (CL/CS/MX/PA/PC/VZ) and
SLV-LX60S (MX))
VIDEO CASSETTE RECORDER
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO IN, phono jacks (1 each) (SLV-LX50
and LX40), (2 each) (SLV-LX70S and LX60S)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
—1—
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
—2—
4.
5.
Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
Check the B+ voltage to see it is at the values specified.
Section
SERVICE NOTE
Title
TABLE OF CONTENTS
Page Section
1.
ERROR CODE INDICATION ........................................... 5
1
GENERAL
Getting Started ........................................................................... 1-1
Step 2 : Setting up the remote commander ............................. 1-1
Step 3 : Hookups ..................................................................... 1-1
Selecting a language ............................................................... 1-4
Setting the clock ...................................................................... 1-4
Presetting channels .................................................................. 1-6
Basic Operations ........................................................................ 1-8
Playing a tape .......................................................................... 1-8
Recording TV programs .......................................................... 1-8
Recording TV programs using the Dial Timer ........................ 1-9
Recording TV programs using the Timer ............................. 1-10
Additional Operations ............................................................. 1-11
Locking the VCR (Child Lock) ............................................. 1-11
Playing/searching at various speeds ...................................... 1-11
Setting the recording duration time ....................................... 1-12
Checking/changing/canceling timer settings ........................ 1-12
Recording stereo and bilingual programs ............................. 1-13
Searching using for the begining of a timer recorded
program ......................................................................... 1-13
Searching using the index function ....................................... 1-13
Searching using the time search function ............................. 1-14
Skip-searching automatically (Quick view) .......................... 1-14
Searching for a selected point on the tape ............................ 1-14
Adjusting the picture ............................................................. 1-15
Changing menu options ........................................................ 1-15
Editing with another VCR ..................................................... 1-16
Additional Information ............................................................ 1-16
General setup information ..................................................... 1-16
Index to parts and controls .................................................... 1-18
Title
Page
• MA-405 (4/79)(AUDIO PROCESS)
SCHEMATIC DIAGRAM ............................ 4-13
• MA-405 (5/7)(TUNER)
SCHEMATIC DIAGRAM ............................ 4-15
• MA-405 (6/7)(DISPLAY CONTROL)
SCHEMATIC DIAGRAM ............................ 4-17
• MA-405 (7/7)(POWER SUPPLY)
SCHEMATIC DIAGRAM ............................ 4-19
• FJ-32 (LINE-2 IN)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ............................ 4-23
• DI-80 (DIAL TIMER)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ............................ 4-24
5
INTERFACE, IC PIN FUNCTION
DESCRIPTION
5-1. SYSTEM CONTROL — MECHANISM BLOCK
INTERFACE (MA-405 BOARD IC160) ....................... 5-1
5-2. SYSTEM CONTROL — SERVO PERIPHERAL
CIRCUIT INTERFACE (MA-405 BOARD IC160) ...... 5-1
5-3. SYSTEM CONTROL — SYSTEM CONTROL
PERIPHERAL CIRCUIT INTERFACE
(MA-405 BOARD IC160) .............................................. 5-2
5-4. SYSTEM CONTROL AND RF MODULATOR
— INPUT SELECTION BLOCK INTERFACE
(MA-405 BOARD IC160) .............................................. 5-2
5-5. SYSTEM CONTROL — VIDEO/RP BLOCK
INTERFACE (MA-405 BOARD IC160) ....................... 5-2
5-6. SYSTEM CONTROL — AUDIO BLOCK INTERFACE
(MA-405 BOARD IC160) .............................................. 5-2
5-7. SERVO/SYSTEM CONTROL MICROPROCESSOR
PIN FUNCTIONS (MA-405 BOARD IC160) ............... 5-3
2
DISASSEMBLY
6
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
CASE, FRONT PANEL BLOCK ASSEMBLY .............. 2-1
DI-80 BOARD, FJ-32BOARD ........................................ 2-1
REAR PANEL ................................................................. 2-2
MA-405 BOARD ............................................................ 2-2
MECHANISM DECK ..................................................... 2-3
INTERNAL VIEWS ........................................................ 2-4
CIRCUIT BOARDS LOCATION ................................... 2-5
6-1 MECHANICAL ADJUSTMENTS ................................. 6-1
6-2. ELECTRICAL ADJUSTMENTS ................................... 6-1
2-1. PREPARATION BEFORE ADJUSTMENT ................... 6-1
2-1-1. Equipment Required ..................................................... 6-1
2-1-2. Equipment Connection ................................................. 6-1
2-1-3. Set-up of Adjustment .................................................... 6-1
2-1-4. Alignment Tape ............................................................. 6-1
2-1-5. Input/Output Levels and Impedance ............................. 6-2
2-1-6. Adjustment Sequence ................................................... 6-2
2-2. POWER SUPPLY CHECK ............................................. 6-2
2-2-1. Output Voltage Check (MA-405 Board) ...................... 6-2
2-3. SERVO SYSTEM CHECK ............................................. 6-3
2-3-1. RF Switching Position Adjustment (MA-405 Board) ... 6-3
2-4. AUDIO SYSTEM ADJUSTMENT ................................. 6-3
2-4-1. Hi-Fi Audio System Adjustment (Hi-Fi model only) ... 6-3
2-4-2. HiFi Switching Position Adjustment (MA-405 Board) 6-4
2-4-3. Normal Audio System Adjustment ............................... 6-4
2-4-4. Audio Level and Distortion Check ............................... 6-4
2-4-5. Audio Noise Check ....................................................... 6-4
2-4-6. ACE Head Adjustment .................................................. 6-4
2-4-7. E-E Output Level Check ............................................... 6-4
2-4-8. Frequency Response Check .......................................... 6-4
2-5. ADJUSTING PARTS LOCATION DIAGRAM ............. 6-6
3
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
OVERALL BLOCK DIAGRAM .................................... 3-1
VIDEO BLOCK DIAGRAM .......................................... 3-3
SERVO/SYSTEM CONTROL BLOCK DIAGRAM ..... 3-5
TUNER BLOCK DIAGRAM ......................................... 3-7
AUDIO BLOCK DIAGRAM .......................................... 3-9
POWER BLOCK DIAGRAM ....................................... 3-11
4
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ................................ 4-3
4-2. PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAMS .................................................................... 4-5
• MA-405 (VIDEO, AUDIO, SERVO/SYSTEM
CONTROL, TUNER, POWER)
PRINTED WIRING BOARD ......................... 4-5
• MA-405 (1/7)(REC/PB HEAD AMP)
SCHEMATIC DIAGRAM .............................. 4-7
• MA-405 (2/7)(Y/C, AUDIO PROCESS)
SCHEMATIC DIAGRAM .............................. 4-9
• MA-405 (3/7)(SERVO/SYSTEM CONTROL)
SCHEMATIC DIAGRAM ............................ 4-11
7
ADJUSTMENTS
REPAIR PARTS LIST
7-1. EXPLODED VIEWS ...................................................... 7-1
7-1-1. FRONT PANEL AND UPPER CASE SECTION ........ 7-1
7-1-2. CHASSIS SECTION .................................................... 7-2
7-1-3. MECHANISM DECK SECTION-1 ............................. 7-3
7-1-4. MECHANISM DECK SECTION-2 ............................. 7-4
7-1-5. MECHANISM DECK SECTION-3 ............................. 7-5
7-2. ELECTRICAL PARTS LIST .......................................... 7-6
—3—
SERVICE NOTE
1. ERROR CODE INDICATION
• Error codes are indicated using the lower 5 digits in the fluorescent display tube.
“At this time, Colon “:” between character is not indicated.”
Mode code indication when the error has occurred.
Error code
ERROR CODE
0 No error
1 Cam encoder error Loading direction
2 Cam encoder error Unloading direction
3 T reel error
4 S reel error
5 Capstan error
6 Drum error
7 Error on initializing
8 Cassette loading error
9 Reserve
MODE CODE
0 Power-on eject
1 Power-on initial
2 Power-off eject
3 Power-off stop
4 FF
5 REW
6 REC
7 REC- pause
8 Power-on stop
9 PB
10
11
12
13
14
15
16
17
18
19
FWD x1
FWD x2
CUE
PB-pause
RVS-pause
RVS x1
RVS x2
REV
Power-off initial
Mecha. error (Power off)
—4—
20
21
22
23
24
25
26
27
28
REW play
Cas. loading
Tape loading
Power-off loading
Mecha. error (Power on)
Power-on eject initial
Power-off eject initial
APC REC
Cas. loading
(No auto PB check)
SLV-LX40/LX50/LX60S/LX70S
This section is a translated version of
Instruction Manual SLV-LX70S model
Part number: 3-065-284-12
SECTION 1
GENERAL
Controlling other TVs with the remote commander
(SLV-LX70S and LX60S only)
Step 2 : Setting up the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer’s code number.
Inserting the batteries
1 Set •TV / VIDEO at the top of the remote commander to •TV.
down ?/1, and enter your TV’s code number using the number buttons.
2 Hold
Then release ?/1.
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Now you can use the ?/1, VOL +/–, CH +/–, and TV/VIDEO buttons to control your
TV. You can also use the buttons marked with a dot (•) to control a Sony TV. To
control the VCR, reset •TV / VIDEO to VIDEO.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
Remote sensor
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV.
•TV / VIDEO
1
2
3
Code
number
Code
number
TV brand
JVC
09
RCA
04, 10
KMC
03
Sampo
12
04
Magnavox
03, 08, 12
Sanyo
11
12
Marantz
04, 13
Scott
12
Coronado
03
MGA/Mitsubishi
04, 12, 13, 17
Sears
07, 10, 11
Curtis-Mathes
12
NEC
04, 12
Sharp
03, 05, 18
Daytron
12
Panasonic
06, 19
Sylvania
08, 12
03, 08, 14
TV brand
Code
number
TV brand
Sony
01
Akai
04
AOC
Centurion
Emerson
03, 04, 14
Philco
03, 04
Teknika
To operate
Set •TV / VIDEO to
Fisher
11
Philips
08
Toshiba
07
the VCR
VIDEO and point at the remote sensor at the VCR
General Electric
06, 10
Pioneer
16
Wards
03, 04, 12
a Sony TV
•TV and point at the remote sensor at the TV
Gold Star
03, 04, 17
Portland
03
Yorx
12
Hitachi
02, 03
Quasar
06, 18
Zenith
15
J.C.Penney
04, 12
Radio Shack
05, 14
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the
VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
• When you press the AUDIO MONITOR button, your TV’s menu may appear on the TV
screen. To exit the TV menu, press the MENU button on the TV remote commander or wait
until the menu disappears automatically.
continued
Setting up the remote commander
5
6
Setting up the remote commander
Audio/video (A/V) hookup
Step 3 : Hookups
If your TV has audio/video (A/V) input jacks, you will get a better picture and sound
if you hook up your VCR using these connections. If your TV doesn’t have A/V
inputs, see the following pages for antenna or cable hookups.
Selecting the best hookup option
If you’re not planning to use your VCR to record programs, you’re finished setting up
the VCR after you’ve made the connections shown on pages 8 and 9. If you want to
record regular or cable TV programs, complete these connections first, and then go to
the following pages for antenna or cable hookups.
There are many ways in which your VCR can be hooked up. To hook up your VCR
so that it works best for you, first scan through the table below. Then use the
accompanying diagrams and procedures on the following pages to set up your VCR.
If your TV has audio/video inputs, refer to pages 8 and 9 for audio/video (A/V)
hookup. Then follow one of the hookups below. If your TV doesn’t have A/V inputs,
go directly to one of the hookups below.
If you have
Use
Antenna only, no cable TV
Hookup 1
Pages 10 to 11
No cable box or cable box with only a few
scrambled channels
Hookup 2
Pages 12 to 14
For SLV-LX70S and LX60S
For a true “home theater” experience, you should connect the audio outputs of your
VCR or TV to your stereo system.
Refer to
A Use this hookup if your TV has stereo jacks
VCR
Stereo receiver
TV
AUDIO VIDEO
Cable box with many scrambled channels
Hookup 3
Pages 15 to 17
AUX IN
LINE-1 IN
IN
LINE OUT
VIDEO
After you’ve completed the connections, follow the instructions for setup. During
setup, if you need more details on the procedure described, page numbers are
provided where you can find complete, step-by-step instructions.
AUDIO OUT
AUDIO
After you’ve completed the setup, you’re ready to use your VCR. Procedures differ
depending on the hookup you used. For an overview, refer to “Quick reference to
using the VCR” on the back cover.
Audio/video cable (supplied)
Before you get started
• Turn off the power to all equipment.
• Do not connect the AC power cords until all of the connections are completed.
• Be sure to make connections firmly. Loose connections may cause picture
distortion.
• If your TV doesn’t match any of the examples provided, see your nearest Sony
dealer or qualified technician.
Audio cable (not supplied)
B Use this hookup if your TV doesn’t have stereo jacks
VCR
Stereo receiver
TV
AUDIO VIDEO
AUX IN
LINE-1 IN
LINE OUT
IN
VIDEO
AUDIO
Video cable (not supplied)
Audio cable (not supplied)
Notes
• If you don’t have a stereo receiver, connect the white LINE OUT/AUDIO L jack to the
AUDIO IN jack on your TV.
• To play a tape in stereo, you must use the A/V connection.
• If you use the Trinitron TV Synchro Play function (see page 34), the A/V connection is
necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO
IN 1 jacks.)
Hookups
7
8
1-1
Hookups
For SLV-LX50 and LX40
Hookup 1
A Use this hookup if your TV has stereo jacks
Antenna hookup
VCR
Make the following connections if you’re using an antenna (if you don’t have cable
TV).
TV
AUDIO VIDEO
LINE-1 IN
A Use this hookup if you’re using:
• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
IN
LINE OUT
VIDEO
AUDIO
Rear of TV
VHF/UHF
Audio/video cable (not supplied)
A
B Use this hookup if your TV doesn’t have stereo jacks
or
VHF
VCR
VCR
B
VHF/UHF
TV
IN
UHF
AUDIO VIDEO
or
OUT
LINE-1 IN
LINE OUT
Match the type of
connector on your
TV: A, B, or C.
VHF
IN
C
VIDEO
AUDIO
UHF
Audio/video cable (not supplied)
B Use this hookup if you’re using a VHF-only antenna (you get
channels 2–13 only)
Note
• If you use the Trinitron TV Synchro Play function (see page 34), the A/V connection is
necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO
IN 1 jacks.)
Rear of TV
VHF/UHF
A
Completing A/V hookup
or
After you’ve connected your TV and completed antenna or cable hookup, return to
this procedure to complete VCR set up. This will prevent unwanted noise in the RF
channel.
B
VHF/UHF
IN
UHF
or
OUT
Press MENU and select
OPCIONES.
VHF
VCR
Set SELEC. AUTO. ANT.
to NO and press OK.
PROG. / VERIF.
VHF
For connector types
B and C, no UHF
connection is
required.
C
OPCIONES
PÁGINA 1
AJUSTES
SELEC. AUTO. ANT.
ESTEREO AUTO.
SINTONIZ. AUDIO
SELC. DE CINTA
VEL. AUTO. CINTA
OPCIONES
,
SELECCIONAR
AJUSTAR
PARA SALIR
Match the type of
connector on your
TV: A, B, or C.
UHF
SI
NO
AUTO
SI
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external
antenna connector (not supplied) so you can connect the cable to the VHF/UHF IN
connector. If you have separate cables for VHF and UHF antennas, you should use a
U/V band mixer (not supplied). For details, see page 68.
PRÓXIMA
VOLVER
:
: OK
: MENU
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
For details, see page 62.
Hookups
9
10
Hookup 1 : VCR setup
Hookups
Hookup 2
Before you start…
• Turn on the VCR and the TV.
• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
You have no cable box, or a cable box with only a few
scrambled channels
the RF UNIT switch to CH3
1 Set
or CH4, whichever channel is not
Recommended use
Use this hookup if you do not have a cable box. Also use this hookup if your cable
system scrambles only a few channels.
2
3
used in your area. If both are
RF UNIT
used, set the switch to either
CH3 CH4
channel. For details, see page 67.
If you made A/V connections
(from page 8), you do not need to
adjust the RF UNIT switch.
Change the on-screen display language to English, if desired. For details, see
page 18.
Press EASY SET UP on the VCR.
What you can do with this hookup
• Record any unscrambled channel by selecting the channel on the VCR
What you can’t do
• Record scrambled channels that require a cable box
VCR
Wall
EASY SET UP
VHF/UHF
IN
OUT
1 The RELOJ menu appears. Select MANUAL
and press OK. Then set the clock. For details,
see page 24.
or
AJUSTE
RELOJ
AUTO
MANUAL
SELECCIONAR
SIGUIENTE
CANCELAR
2 The SINTONIZADOR menu appears. Set
ANTENA/CABLE to ANT and press OK.
For details, see page 26.
Connect this cable
directly to your TV
if you don’t have a
cable box.
:
: OK
: EASY SET UP
AJUSTE
SINTONIZADOR
OUT
ANT
CABLE
:
: OK
: EASY SET UP
3 The AJUSTE AUTO. starts.
AJUSTE
SINTONIZADOR
Cable box
IN
ANTENA / CABLE
SELECCIONAR
SIGUIENTE
CANCELAR
or
AJUSTE
CH 2 4
AJUSTE AUTO.
AJUSTE CONCLUIDO
EJECUTANDO
POR FAVOR ESPERE
You have now completed hookup.
Hookups
11
12
1-2
Hookups
Rear of TV
VHF/UHF
A Match the
type of
connector on
your TV: A,
VHF
B, or C.
B
For
connector
UHF
types B and
VHF
C, no UHF
connection
C
is required.
UHF
3 The SINTONIZADOR menu appears. Set
ANTENA/CABLE to CABLE and press OK.
For details, see page 26.
Hookup 2 : VCR setup
Before you start…
• Turn on the VCR and the TV.
AJUSTE
SINTONIZADOR
ANT
CABLE
ANTENA / CABLE
• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
SELECCIONAR
SIGUIENTE
CANCELAR
the RF UNIT switch to CH3
1 Set
or CH4, whichever channel is not
used in your area. If both are
used, set the switch to either
channel. For details, see page 67.
:
: OK
: EASY SET UP
4 The AJUSTE AUTO. starts.
RF UNIT
CH3 CH4
AJUSTE
SINTONIZADOR
AJUSTE
CH 2 4
AJUSTE AUTO.
2
3
AJUSTE CONCLUIDO
If you made A/V connections
(from page 8), you do not need to
adjust the RF UNIT switch.
Change the on-screen display language to English, if desired. For details, see
page 18.
Press EASY SET UP on the VCR.
EJECUTANDO
POR FAVOR ESPERE
EASY SET UP
You have now completed hookup.
1 The RELOJ menu appears. Select AUTO and
press OK. For details, see page 20.
Automatic clock setting
Once you’ve set up the VCR, it automatically sets the clock the first time you turn off
the VCR. “ACS” (Auto Clock Set) will flash in the display window and search for a
time signal provided by Sony Entertainment Television (SETV). After that,
whenever you turn off the VCR, it checks the time and adjusts the clock, even for
Daylight Saving Time.
AJUSTE
RELOJ
AUTO
MANUAL
SELECCIONAR
SIGUIENTE
CANCELAR
2 The PAIS/ZONA DE HORARIO menu
appears. Select the country you want to set
and press OK. You can select the following
countries:
BELIZE y BOLIVIA y CHILE y
COLOMBIA y COSTA RICA y CUBA
y REP. DOMIN. y ECUADOR y
EL SALVADR y GUATEMALA y
GUYANA y HONDURAS y JAMAICA
y MEX-CENTRO y MEX-MONT. y
MEX-PACIF. y MEX-S. ESTE y
NICARAGUA y PANAMA y PERU y
SURINAM y TRIN. & TOB. y
VENEZUELA
If you want to use the timer to record right away, or if the cable TV station in your
area does not broadcast SETV, or if SETV in your area does not carry time signals,
set the clock manually. For details, see page 23.
:
: OK
: EASY SET UP
Notes
• If the clock is not set, “ACS” will flash in the display window whenever the VCR is turned
off. During this time, the VCR will search for a time signal.
• The Daylight Saving Time start and end days may differ depending on the year. To ensure
correct switching, select SI or NO for the HORARIO VERANO setting (page 22).
AJUSTE
PAIS / ZONA DE HORARIO
BELIZE
BOLIVIA
CHILE
COLOMBIA
COSTA RICA
CUBA
REP. DOMIN.
ECUADOR
EL SALVADR
SELECCIONAR
SIGUIENTE
CANCELAR
:
: OK
: EASY SET UP
continued
Hookups
13
14
Hookups
Hookup 3 : VCR setup
Hookup 3
Before you start…
• Turn on the VCR and the TV.
Connecting a cable box with many scrambled channels
Recommended use
Use this hookup if your cable system scrambles all or most channels.
• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
the RF UNIT switch to CH3
1 Set
or CH4, whichever channel is not
What you can do with this hookup
• Record any channel by selecting the channel on the cable box
used in your area. If both are
used, set the switch to either
channel. For details, see page 67.
What you can’t do
• Record with the cable box turned off
• Record one channel while watching another channel
Cable box
Wall
A
OUT
CH3 CH4
If you made A/V connections
(from page 8), you do not need to
adjust the RF UNIT switch.
Turn on your cable box.
2
the on-screen display language to English, if desired. For details, see
3 Change
page 18.
Press EASY SET UP on the VCR.
4
EASY SET UP
Rear of TV
VHF/UHF
IN
RF UNIT
or
Match the type of
connector on your
TV: A, B, or C.
VHF
B
or
UHF
For connector
types B and C, no
UHF connection
is required.
1 The RELOJ menu appears. Select AUTO and
press OK. For details, see page 20.
VHF
VCR
AJUSTE
RELOJ
AUTO
MANUAL
C
VHF/UHF
IN
UHF
OUT
SELECCIONAR
SIGUIENTE
CANCELAR
2 The PAIS/ZONA DE HORARIO menu
appears. Select the country you want to set
and press OK. You can select the following
countries:
BELIZE y BOLIVIA y CHILE y
COLOMBIA y COSTA RICA y CUBA
y REP. DOMIN. y ECUADOR y
EL SALVADR y GUATEMALA y
GUYANA y HONDURAS y JAMAICA
y MEX-CENTRO y MEX-MONT. y
MEX-PACIF. y MEX-S. ESTE y
NICARAGUA y PANAMA y PERU y
SURINAM y TRIN. & TOB. y
VENEZUELA
continued
Hookups
15
16
1-3
Hookups
:
: OK
: EASY SET UP
AJUSTE
PAIS / ZONA DE HORARIO
BELIZE
BOLIVIA
CHILE
COLOMBIA
COSTA RICA
CUBA
REP. DOMIN.
ECUADOR
EL SALVADR
SELECCIONAR
SIGUIENTE
CANCELAR
:
: OK
: EASY SET UP
3 The SINTONIZADOR menu appears. Set
ANTENA/CABLE to ANT and press OK.
For details, see page 26.
AJUSTE
SINTONIZADOR
Selecting a language
ANT
CABLE
ANTENA / CABLE
You can change the on-screen display
language.
SELECCIONAR
SIGUIENTE
CANCELAR
:
: OK
: EASY SET UP
4 The AJUSTE AUTO. starts.
AJUSTE
SINTONIZADOR
MENU
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the VCR channel (channel 3
or 4). If your TV is connected to the VCR
using A/V connections, set the TV to video
input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
AJUSTE
CH 2 4
AJUSTE AUTO.
AJUSTE CONCLUIDO
EJECUTANDO
M/m
OK
POR FAVOR ESPERE
Automatic clock setting
Once you’ve set up the VCR, it automatically sets the clock the first time you turn off
the VCR. “ACS” (Auto Clock Set) will flash in the display window and search for a
time signal provided by Sony Entertainment Television (SETV). After that,
whenever you turn off the VCR, it checks the time and adjusts the clock, even for
Daylight Saving Time.
1
MENU
Press MENU, then press M/m to highlight
AJUSTES and press OK.
To use the Auto Clock Set feature with this hookup, you need to manually select
SETV:
PLAY
SELECCIONAR
AJUSTAR
PARA SALIR
OK
1
2 Select AUTO in the RELOJ menu to turn on the Auto Clock Set feature.
off the VCR. It automatically sets the clock and adjusts for Daylight Saving
3 Turn
Time by picking up the time signal.
Tune the cable box to SETV.
2
PLAY
Press M/m to highlight SELECCION DEL
IDIOMA, then press OK.
ENGLISH
ESPAÑOL
SELECCIONAR
AJUSTAR
PARA SALIR
If you want to use the timer to record right away, or if the cable TV station in your
area does not broadcast SETV, or if SETV in your area does not carry time signals,
set the clock manually. For details, see page 23.
PLAY
OK
Tip
• If you want to return to the previous menu, highlight VOLVER and press OK.
17
18
Selecting a language
3
Setting the clock
PLAY
Using the Auto Clock Set
feature
Press M/m to highlight AUTO, then press
OK.
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
4
MENU
PLAY
The Auto Clock Set feature works only if
SETV in your area broadcasts time signals. If
SETV in your area does not broadcast time
signals or if you select Hookup 1 on page 10
set the time manually (page 23).
Press M/m to highlight TOTAL. AUTO.,
then press OK.
2
PLAY
SI
NO
CH AJUSTE RELOJ
HORARIO VERANO
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
Press M/m to highlight SI, then press OK.
5
PLAY
OK
6
7
AJUSTES
MENU
Press MENU to exit the menu.
To activate the Auto Clock Set function, turn off the VCR. “ACS” will flash
in the display window.
The VCR automatically sets the clock by searching for the SETV broadcast
that carries time signals and sets Daylight Saving Time (if applicable).
PREAJUSTE DEL SINTONIZADOR
AJUSTE DEL RELOJ
SELECCION DEL IDIOMA
VOLVER
If your clock is incorrectly set to Daylight Saving Time, you can adjust
these settings without turning off the Auto Clock Set feature (page 21).
SELECCIONAR
AJUSTAR
PARA SALIR
Press M/m to highlight AJUSTE DEL
RELOJ, then press OK.
AJUSTE AUTOMATICO RELOJ
TOTAL. AUTO.
M/m
OK
PLAY
OK
:
: OK
: MENU
VOLVER
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the VCR channel (channel 3
or 4). If your TV is connected to the VCR
using A/V connections, set the TV to video
input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
When using the EASY SET UP procedure,
skip steps 1 and 2.
SI
CH AJUSTE RELOJ
HORARIO VERANO
OK
Press MENU, then press M/m to highlight
AJUSTES and press OK.
AJUSTE AUTOMATICO RELOJ
TOTAL. AUTO.
OK
Sony Entertainment Television (SETV)
transmits time signals with its broadcasts. If
the cable TV station in your area broadcasts
SETV and transmits these time signals, your
VCR can pick up these time signals to
automatically set the clock.
MENU
:
: OK
: MENU
Press M/m to highlight ENGLISH or ESPAÑOL, then press OK.
3
Notes
• To use the Auto Clock Set feature, leave the cable box on.
• If the clock is not set, “ACS” will flash in the display window whenever the VCR is turned
off. During this time, the VCR will search for a time signal.
• The Daylight Saving Time start and end days may differ depending on the year. To ensure
correct switching, select SI or NO for the HORARIO VERANO setting (page 22).
1
:
: OK
: MENU
SELECCION DEL IDIOMA
OK
You have now completed hookup
Hookups
AJUSTES
PREAJUSTE DEL SINTONIZADOR
AJUSTE DEL RELOJ
SELECCION DEL IDIOMA
VOLVER
:
: OK
: MENU
Tip
• If you want to return to the previous menu, highlight VOLVER and press OK.
AJUSTE DEL RELOJ
Notes
• The clock cannot be set automatically if you don’t receive SETV broadcast that carries time
signals in your area. If so, set the clock manually (page 23).
• Depending on the channels allotted to SETV in your area, setting the clock automatically
may take up to about 30 minutes. If nothing happens even after you wait about 30 minutes
after turning off the VCR, turn the VCR on and then off again. If the clock is not set even
after about another 30 minutes, set the clock manually (page 23).
• If the clock is not set, “ACS” will flash in the display window whenever the VCR is turned
off. During this time, the VCR will search for a time signal.
AUTO
MANUAL
OK
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
continued
Setting the clock
19
20
1-4
Setting the clock
If the clock does not activate
Press M/m to highlight NO for TOTAL.
AUTO. and press OK.
2
PLAY
OK
AJUSTE AUTOMATICO RELOJ
TOTAL. AUTO.
NO
CH AJUSTE RELOJ
HORARIO VERANO
–––
AUTO
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
1
2
Press M/m to highlight the item you want to
set and press OK. Then press M/m to make
the setting and press OK.
3
3
PLAY
4
5
6
7
8
9
Number
buttons
:
: OK
: MENU
OK
0
1
2
3
4
5
6
7
8
9
0
• For CH AJUSTE RELOJ
Leave the setting to “– – –” to have the
VCR automatically search for the SETV
broadcast.
Or, press the number buttons to select the
SETV channel if you know it.
• For HORARIO VERANO
Select SI or NO (standard time), or
AUTO to have the VCR automatically set
the daylight saving time.
MENU
AJUSTE AUTOMATICO RELOJ
TOTAL. AUTO.
NO
CH AJUSTE RELOJ
HORARIO VERANO
123
AUTO
VOLVER
USE
AJUSTAR
PARA SALIR
: 0–9
: OK
: MENU
AJUSTE AUTOMATICO RELOJ
TOTAL. AUTO.
NO
CH AJUSTE RELOJ
HORARIO VERANO
VOLVER
M/m
OK
SELECCIONAR
AJUSTAR
PARA SALIR
4
1
Follow steps 1 to 4 in “Using the Auto
Clock Set feature.”
5
:
: OK
: MENU
Press MENU to exit the menu.
To activate the Auto Clock Set function, turn off the VCR. “ACS” will flash
in the display window.
AJUSTE AUTOMATICO RELOJ
TOTAL. AUTO.
The TOTAL. AUTO. menu is displayed.
MENU
AUTO
SI
NO
Tip
• If you want to return to the previous menu, highlight VOLVER and press OK.
SI
NO
CH AJUSTE RELOJ
HORARIO VERANO
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
Notes
• The Daylight Saving Time start and end days may differ depending on the year. To ensure
correct switching, select SI or NO for the HORARIO VERANO setting.
• If nothing happens even after you wait about 30 minutes after turning off the VCR, turn the
VCR on and then off again. If the clock is not set even after about another 30 minutes, set the
clock manually (page 23).
• Some cable TV stations broadcasting SETV do not transmit time signals. If so, set the clock
manually (page 23).
:
: OK
: MENU
continued
Setting the clock
21
22
Using Manual Clock Set
Setting the clock
3
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the VCR channel (channel 3
or 4). If your TV is connected to the VCR
using A/V connections, set the TV to video
input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
PLAY
Press M/m to highlight MANUAL, then
press OK.
AJUSTE DEL RELOJ
1 /
1 / 2 0 0 1 LUN
1 2 : 0 0 AM
OK
SELECCIONAR
AJUSTAR
FIN
PARA SALIR
:
:
: OK
: MENU
MENU
Press M/m to set the day.
4
AJUSTE DEL RELOJ
PLAY
28 /
M/m/</,
OK
1 / 2 0 0 1 DOM 1 2 : 0 0 AM
OK
SELECCIONAR
AJUSTAR
FIN
PARA SALIR
5
PLAY
Press , to highlight the month and press
M/m to set the month.
:
:
: OK
: MENU
AJUSTE DEL RELOJ
28 /
9 / 2 0 0 1 VIE
OK
SELECCIONAR
AJUSTAR
FIN
PARA SALIR
1
MENU
Press MENU, then press M/m to highlight
AJUSTES and press OK.
When using the EASY SET UP procedure,
skip steps 1 and 2.
6
AJUSTES
Set the year, hour, and minutes in the same way as the month.
The day of the week is set automatically.
PREAJUSTE DEL SINTONIZADOR
AJUSTE DEL RELOJ
SELECCION DEL IDIOMA
VOLVER
7
PLAY
:
:
: OK
: MENU
Press OK to start the clock.
PLAY
SELECCIONAR
AJUSTAR
PARA SALIR
OK
2
PLAY
Press M/m to highlight AJUSTE DEL
RELOJ, then press OK.
:
: OK
: MENU
OK
Tip
• If you want to return to the previous menu, highlight VOLVER and press OK.
AJUSTE DEL RELOJ
AUTO
MANUAL
OK
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
continued
Setting the clock
23
24
1-5
Setting the clock
1 2 : 0 0 AM
Press M/m to highlight ANTENA/CABLE, then press OK.
3
Presetting channels
PLAY
This VCR is capable of receiving VHF
channels 2 to 13, UHF channels 14 to 69 and
unscrambled CATV channels 1 to 125. First,
we recommend that you preset the receivable
channels in your area using automatic
presetting methods. Then, if there are any
unwanted channels, disable them manually.
If you have already decided which channels
you wish to preset, set them directly using
manual presetting methods.
OK
4
PLAY
MANUAL
AFT
SINTONIA FINA
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
PLAY
M/m
OK
OK
Presetting all receivable channels automatically
When using the EASY SET UP procedure,
skip steps 1 and 2.
:
: OK
: MENU
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
AJUSTES
PREAJUSTE DEL SINTONIZADOR
AJUSTE DEL RELOJ
SELECCION DEL IDIOMA
VOLVER
+
SI
Press M/m to highlight AJUSTE AUTO.,
then press OK.
:
: OK
: MENU
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
All receivable channels are preset in
numerical sequence. When no more
receivable channels can be found, presetting
stops and the picture from the lowest
numbered channel is displayed on the TV
screen.
CABLE
AJUSTE AUTO.
MANUAL
AFT
SINTONIA FINA
VOLVER
+
SI
POR FAVOR ESPERE
PLAY
SELECCIONAR
AJUSTAR
PARA SALIR
OK
2
PLAY
Press M/m to highlight PREAJUSTE DEL
SINTONIZADOR, then press OK.
OK
:
: OK
: MENU
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
1
CABLE
AJUSTE AUTO.
+
SI
MANUAL
AFT
SINTONIA FINA
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
continued
Presetting channels
25
26
Tips
• When receiving a VHF, UHF, or CATV channel, the display changes as follows each time
you press DISPLAY.
Presetting channels
Presetting/disabling channels manually
Channel number
Remaining tape length, and time counter
The bar indicator and pointer for searching for a specific place on a tape
No display
1
2
3
4
5
6
7
8
9
Number
buttons,
ENTER
0
• If you want to return to the previous menu, highlight VOLVER and press OK.
CH +/–
MENU
M/m
OK
1
MENU
Press MENU, then press M/m to highlight
AJUSTES and press OK.
AJUSTES
PREAJUSTE DEL SINTONIZADOR
AJUSTE DEL RELOJ
SELECCION DEL IDIOMA
VOLVER
PLAY
OK
continued
Presetting channels
27
28
1-6
Presetting channels
2
ANT
AJUSTE AUTO.
SELECCIONAR
AJUSTAR
PARA SALIR
OK
Press MENU, then press M/m to highlight
AJUSTES and press OK.
• To preset VHF and UHF channels:
Press M/m to set ANTENA/CABLE to
ANT, then press OK.
+
SI
MANUAL
AFT
SINTONIA FINA
VOLVER
5
1
CABLE
AJUSTE AUTO.
MENU
PLAY
MENU
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
OK
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the VCR channel (channel 3
or 4). If your TV is connected to the VCR
using A/V connections, set the TV to video
input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
1
• To preset cable TV channels:
Press M/m to set ANTENA/CABLE to
CABLE, then press OK.
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
1
Press M/m to highlight PREAJUSTE DEL
SINTONIZADOR, then press OK.
2
PLAY
If the picture is not clear
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
AJUSTE AUTO.
OK
MANUAL
AFT
SINTONIA FINA
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
3
1
2
3
4
5
6
7
8
9
0
• To preset a channel:
1 Press the number buttons to enter the
channel number, then press ENTER.
2 Press OK.
3 Press M/m to set MANUAL to +, then
press OK.
PLAY
• To disable a channel:
1 Press CH +/– to select the channel
number.
2 Press OK.
3 Press M/m to set MANUAL to –, then
press OK.
• CH
PLAY
OK
+
SI
:
: OK
: MENU
Channel to be preset
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
5
1
2
3
4
5
6
7
8
9
CABLE
AJUSTE AUTO.
+
SI
MANUAL
AFT
SINTONIA FINA
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
OK
4
Normally, the Auto Fine Tuning (AFT)
function automatically tunes in channels
clearly. If, however, the picture of a channel
is not clear, you can also use the manual
tuning function.
1
CABLE
Number
buttons,
ENTER
0
:
: OK
: MENU
Channel to be disabled
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
5
CABLE
MENU
AJUSTE AUTO.
–
SI
MANUAL
AFT
SINTONIA FINA
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
M/m/</,
OK
Repeat step 3 to preset or disable channels as required, then press MENU.
MENU
Tip
• If you want to return to the previous menu, highlight VOLVER and press OK.
1
MENU
Press MENU, then press M/m to highlight
AJUSTES and press OK.
AJUSTES
PREAJUSTE DEL SINTONIZADOR
AJUSTE DEL RELOJ
SELECCION DEL IDIOMA
VOLVER
PLAY
SELECCIONAR
AJUSTAR
PARA SALIR
OK
:
: OK
: MENU
continued
29
Presetting channels
30
Presetting channels
Basic Operations
Press M/m to highlight PREAJUSTE DEL
SINTONIZADOR, then press OK.
2
PLAY
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
MANUAL
AFT
SINTONIA FINA
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
3
1
2
3
4
5
6
7
8
9
Press the number buttons to select the
channel you want to fine-tune, then press
ENTER.
+
SI
:
: OK
: MENU
PREAJUSTE DEL SINTONIZADOR
CH
SELECCIONAR
AJUSTAR
PARA SALIR
OK
Press M/m to highlight SINTONIA FINA,
then press OK.
OK
3
5
6
7
8
9
Press </, to adjust to a clearer picture,
then press OK.
5
CABLE
CLEAR
+
X PAUSE
REPLAY
:
: OK
: MENU
PREAJUSTE DEL SINTONIZADOR
CH
ANTENA / CABLE
Note that the AFT setting switches to NO.
0
PREAJUSTE DEL SINTONIZADOR
CH
H PLAY
M FF
5
CABLE
x STOP
AJUSTE AUTO.
SELECCIONAR
AJUSTAR
PARA SALIR
MENU
2
4
AJUSTE AUTO.
MANUAL
AFT
SINTONIA FINA
VOLVER
6
1
:
: OK
: MENU
ANTENA / CABLE
The fine tuning meter appears.
SELECCIONAR
AJUSTAR
PARA SALIR
PLAY
5
CABLE
+
SI
MANUAL
AFT
SINTONIA FINA
VOLVER
5
TRINITRON TV
SYNCHRO PLAY
DISPLAY
AJUSTE AUTO.
MANUAL
AFT
SINTONIA FINA
VOLVER
PLAY
Z EJECT
Selected channel
ANTENA / CABLE
0
4
Playing a tape
1
CABLE
AJUSTE AUTO.
OK
+
NO
m REW
:
: OK
: MENU
Press MENU to exit the menu.
Tips
• To select the channel in step 3 above, you can also use the CH +/– buttons. In this case, you
don’t need to press ENTER.
• If you want to return to the previous menu, highlight VOLVER and press OK.
Note
• When adjusting SINTONIA FINA, the menu may become difficult to read due to interference
from the picture being received.
Presetting channels
31
1
Turn on your TV and set it to the video channel.
2
Insert a tape.
32
1-7
The VCR turns on and starts playing
automatically if you insert a tape with its
safety tab removed.
Playing a tape
Turning on the VCR and TV, and starting playback
automatically (Trinitron TV Synchro Play)
Press H PLAY.
3
PLAY
When the tape reaches the end, it will rewind automatically.
You can only use this function if your TV is made by Sony (Trinitron TV).
OK
How to connect to use this function
Connect the VCR and TV with the audio/video cable (see “Audio/video (A/V)
hookup” on pages 8 and 9). Be sure to connect the audio/video cable to the VIDEO
IN 1 jacks on the TV if the TV has two inputs or more. The TV must be placed
where it will respond to the remote commander while you are pointing it at the VCR.
Additional tasks
To
Press
Stop play
x STOP
Pause play
X PAUSE
Resume play after pause
X PAUSE or H PLAY
Fast-forward the tape
M FF during stop
Rewind the tape
m REW during stop
Eject the tape
Z EJECT
Operation
Make sure that the TV’s power is in standby mode.
Press TRINITRON TV SYNCHRO PLAY and hold the remote commander in place
for about two seconds.
The VCR and TV turn on, and the TV is set to the video channel. If there is a tape in
the VCR, playback starts automatically.
Notes
• If the Trinitron TV Synchro Play function does not work properly:
– Wait a few moments, and press the button again.
– Replace both of the batteries with new ones, and press the button again.
Note that this function may not operate some Sony TVs because of the remote commander’s
signal limitations.
• Do not press TRINITRON TV SYNCHRO PLAY during playback. If you do so, the TV’s
input source will momentarily switch to the TV’s tuner.
To play a recently watched scene
You can immediately rewind and playback the scene you want to watch again.
During playback, press REPLAY up to four times. The VCR rewinds the tape about
ten seconds on the counter for each press of the button, and restarts playback.
To use the time counter
Press CLEAR at the point on the tape that you want to find later. The counter in the
display window resets to “0:00:00.” Search for the point afterwards by referring to
the counter.
VIDEO APC
SP
To display the counter on the TV screen, press DISPLAY.
Notes
• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but the
picture quality cannot be guaranteed.
• While displaying a menu on the TV screen, you cannot use H PLAY, X PAUSE,
M FF, m REW, or x STOP buttons.
• The counter resets to “0:00:00” whenever a tape is reinserted.
• The counter stops counting when it comes to a portion with no recording.
continued
Playing a tape
33
34
3
Recording TV programs
Playing a tape
• CH
Press CH +/– to select the channel or line input video source you want to
record.
VIDEO APC
EP
TV/VIDEO
4
SP / EP
Press SP/EP to select the tape speed, SP or EP.
EP (Extended Play) provides recording time three times as long as SP
(Standard Play). However, SP produces better picture and audio quality.
DISPLAY
1
2
3
4
5
6
7
8
9
VIDEO APC
SP
5
0
REC
Press z REC to start recording.
The recording indicator lights up red in the display window.
CH +/–
Recording indicator
VIDEO APC
SP
z REC
To stop recording
Press x STOP.
SP/EP
To check the remaining tape length
Press DISPLAY repeatedly until the remaining tape length and the time counter
appear on the TV screen.
x STOP
Remaining tape length
SP
0 : 00 : 22
Time counter
To check the remaining tape length of a T-140 or T-180 tape, set SELC. DE CINTA in
the OPCIONES menu to 180. (For details, see page 62.)
1
Turn on your TV and set it to the video channel.
2
Insert a tape with its safety tab in place.
To record from a cable box, turn it on.
continued
Recording TV programs
35
36
1-8
Recording TV programs
To watch another TV program while recording
Recording TV programs using the Dial
Timer
1 Press TV/VIDEO to turn off the VIDEO indicator in the display window.
the TV is connected to the VCR’s LINE OUT jacks, set the TV to the TV’s
2 Ifantenna
input; if not, skip this step.
Select another channel on the TV.
3
To save a recording
To prevent accidental erasure, break
off the safety tab as illustrated. To
record on the tape again, cover the tab
hole with adhesive tape.
The Dial Timer function allows you to make
timer recordings of programs without turning
on your TV. Set the recording timer to record
up to eight programs that will be broadcast
within a month using the DIAL TIMER. The
recording start time and recording stop time
can be set at one minute intervals.
Before you start...
• When using a cable box, turn it on.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
Safety tab
Tips
• To select a channel, you can use the number buttons on the remote commander. Enter the
channel number, then press ENTER.
• You can select a video source from the LINE-1 IN or LINE-2 IN jacks using the INPUT
SELECT button.
• The display appears on the TV screen indicating information about the tape, but the
information won’t be recorded on the tape.
• If you don’t want to watch TV while recording, you can turn off theTV. When using a cable
box, make sure to leave it on.
1
2
3
4
5
6
7
8
9
0
?/1 POWER
DIAL TIMER
INPUT
SELECT
Notes
• The remaining tape length may not be indicated accurately for short tapes such as T-20 or T30, or tapes recorded in the LP mode.
• The display does not appear during still (pause) mode or slow-motion playback.
• It may take up to one minute for the VCR to calculate and display the remaining tape length
after you press DISPLAY.
CHANNEL +/–
1
DIAL TIMER
x STOP
Press DIAL TIMER.
“DIA” and “HOY” appear alternately in the display window.
If the date and time are not set, “DIA” flashes. See step 2 in the following
section “To set the clock” to set the date and time.
VIDEO APC
EP
VIDEO APC
EP
Recording TV programs
2
DIAL TIMER
37
38
6
Turn DIAL TIMER to set the recording date.
Recording TV programs using the Dial Timer
DIAL TIMER
Turn DIAL TIMER to set the recording stop time.
You can set the recording stop time in 15 minute intervals or adjust the time
in one minute intervals by pressing the CHANNEL +/– buttons.
VIDEO APC
EP
VIDEO APC
CHANNEL
3
DIAL TIMER
EP
Press DIAL TIMER.
“DESDE” and the current time appear alternately in the display window.
7
VIDEO APC
EP
DIAL TIMER
Press DIAL TIMER.
The channel number appears in the display window.
VIDEO APC
EP
VIDEO APC
EP
8
4
DIAL TIMER
DIAL TIMER
To record from a source connected to the LINE-1 IN or LINE-2 IN jacks,
turn DIAL TIMER or press INPUT SELECT on the remote commander to
display “L1” or “L2”.
Turn DIAL TIMER to set the recording start time.
You can set the recording start time in 15 minute intervals or adjust the time
in one minute intervals by pressing the CHANNEL +/– buttons.
Turn DIAL TIMER to set the channel number.
VIDEO APC
INPUT
SELECT
EP
VIDEO APC
CHANNEL
EP
9
5
DIAL TIMER
DIAL TIMER
Press DIAL TIMER to complete the setting.
“OK” appears in the display window for about five seconds.
The
indicator appears in the display window and the VCR stands by for
recording. When using a cable box, leave it on.
Press DIAL TIMER.
“HASTA” and the recording stop time appear alternately in the display
window.
To return to the previous step
To return to the previous step, press the CHANNEL + and – buttons on the VCR at
the same time during any of the Dial Timer settings.
VIDEO APC
EP
To stop recording
To stop the VCR while recording, press x STOP.
VIDEO APC
EP
continued
Recording TV programs using the Dial Timer
39
40
1-9
Recording TV programs using the Dial Timer
To use the VCR after setting the timer
Notes
• If eight programs have already been set using the PROG./VERIF. menu, “LLENO” appears in
the display window for about five seconds.
• If you set the clock using the Auto Clock Set function, the clock will adjust itself to the
incoming time signal regardless of adjustments made with the Dial Timer. Be sure you have
set ACS correctly.
To use the VCR before a timer recording begins, just press ?/1. The
indicator
disappears from the display window and the VCR switches on. Remember to press
?/1 to reset the VCR to the timer recording standby mode after using the VCR.
You can also do the following tasks while the VCR is recording:
•
•
•
•
indicator flashes in the display window when you complete the setting in step 9
• The
(page 40) with no tape inserted.
Reset the counter (page 33).
Display tape information on the TV screen (page 36).
Check the timer settings (page 50).
Watch another TV program (page 37).
About the Demonstration Mode
The Dial Timer function has a Demonstration Mode that allows the user, such as a
salesperson, to enter more than eight examples of timer settings when demonstrating
the use of the Dial Timer. It cancels the LLENO notice which appears if eight
programs have already been set. Do not use the Demonstration Mode for making
timer recordings. Doing so may cause the settings to be inaccurate.
To set the clock
1 Turn DIAL TIMER so that “RELOJ” appears in the display window.
DIAL TIMER.
2 Press
“DIA” appears in the display window.
Turn DIAL TIMER to set the day.
3
DIAL TIMER.
4 Press
“MES” appears in the display window.
Turn and press DIAL TIMER to set the month and then the year.
5 After you set the year, “RELOJ” appears in the display window again.
6 Turn and press DIAL TIMER to set the hour and minute.
7 When you have finished setting the time, press DIAL TIMER to start the clock.
To activate the Demonstration Mode
Press X PAUSE on the VCR while turning the DIAL TIMER. “DEMO” appears in
the display window for a few seconds.
To cancel the Demonstration Mode
Turn the power off and unplug the AC power cord. Although the Demonstration
Mode is canceled, the timer settings entered while using the Demonstration Mode
will remain. Be sure to manually cancel the timer settings before you use the Dial
Timer or any other timer method after reconnecting the AC power cord (see page 50).
Tips
• To cancel a Dial Timer setting, press x STOP on the VCR while you are making the setting.
• The program is recorded in the current tape speed. To change the tape speed, press SP/EP
before you complete the setting in step 9 (page 40).
• When you are recording a program in the SP mode and the remaining tape becomes shorter
than the recording time, the tape speed is automatically changed to the EP mode. Note that
some noise will appear on the picture when the tape speed is changed. If you want to keep
the tape speed, set VEL. AUTO. CINTA to NO in the OPCIONES menu (page 62).
• To check, change, or cancel the program setting, see “Checking/changing/canceling timer
settings” (page 50).
continued
Recording TV programs using the Dial Timer
41
42
Press M/m to highlight the line that is to be set, then press OK.
2
Recording TV programs using the timer
PLAY
You can preset up to eight programs together
with the Dial Timer settings at a time.
Before you start…
• Check that the VCR clock is set to the
correct time.
• Turn on your TV and set it to the video
channel. When using a cable box, turn it
on.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
Recording TV programs using the Dial Timer
OK
3
?/1
PLAY
OK
TIMER
1
2
INPUT
SELECT
3
4
5
6
7
8
9
• CH
Set the date, start and stop time, channel
number, and tape speed:
1 Press M/m to set each item.
2 Press , to highlight and set each item
in turn.
To correct a setting, press < to return to
that setting and reset.
PROG. / VERIF.
2 8 / 9 VIE
FECHA
3 0 / 9 DOM
–– / –
–– / –
–– / –
–– / –
–– / –
–– / –
–– / –
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
COM.
8 : 0 0 PM
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
TER.
9 : 0 0 PM
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
:
:
: MENU
FIN : OK
CH
35
––
––
––
––
––
––
––
SP
––
––
––
––
––
––
––
To record the same program every day or the same day every week, press m
while the date is highlighted. For details, see “Daily/weekly recording”
below.
0
To record from a source connected to the LINE-1 IN or LINE-2 IN jacks,
press INPUT SELECT or CH+/– to display “L1” or “L2” in the “CH”
position.
CH +/–
INPUT
SELECT
SP/EP
4
Press OK to confirm the setting.
PLAY
OK
5
M/m/</,
OK
x STOP
6
To enter another setting, press M/m to highlight the next line and repeat step
3.
Press TIMER.
TIMER
Press ?/1 to turn off the VCR.
The
indicator appears in the display window and the VCR stands by for
recording.
When using a cable box, leave it on.
To stop recording
To stop the VCR while recording, press x STOP.
1
TIMER
Press TIMER to display PROG./VERIF.
PROG. / VERIF.
Daily/weekly recording
In step 3 above, press m to select the recording pattern. Each time you press m, the
indication changes as shown below. Press M to change the indication in reverse order.
2 8 / 9 VIE
FECHA
–– / –
–– / –
–– / –
–– / –
–– / –
–– / –
–– / –
–– / –
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
COM.
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
TER.
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
:
: OK
: MENU
CANCELAR : CLEAR
CH
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
the current date t DOM-SAB t LUN-SAB t LUN-VIE t CADA SAB t ..... t
CADA LUN t CADA DOM t 1 month later t (dates count down) t the current
date
continued
Recording TV programs using the timer
43
44
1-10
Recording TV programs using the timer
To use the VCR after setting the timer
Locking the VCR (Child Lock)
To use the VCR before timer recording begins, just press ?/1. The
indicator
disappears from the display window and the VCR switches on. Remember to press
?/1 to reset the VCR to the timer recording standby mode after using the VCR.
After you have set the timer, you can lock all
of the buttons on the VCR so that the settings
are not canceled by mistake.
You can also do the following tasks while the VCR is recording:
•
•
•
•
Reset the counter (page 33).
Display tape information on the TV screen (page 36).
Check the timer settings (page 50).
Watch another TV program (page 37).
?/1 POWER
x STOP
Tips
• To set the channel, you can also use the CH+/– or number buttons.
• To show the PROG./VERIF. menu, you can also use the MENU button. Press MENU, then
press M/m to highlight PROG./VERIF. and press OK.
• To set the tape speed, you can also use the SP/EP button.
• When you are recording a program in the SP mode and the remaining tape becomes shorter
than the recording time, the tape speed is automatically changed to the EP mode. Note that
some noise will appear on the picture when the tape speed is changed. If you want to keep
the tape speed, set VEL. AUTO. CINTA to NO in the OPCIONES menu (page 62).
• To check, change or cancel the program setting, see “Checking/changing/canceling timer
settings” (page 50).
• If you want to return to the previous menu and continue with other operations after setting the
timer, press m to highlight VOLVER, then press OK.
The display returns to the MENU screen.
If you are finished using the VCR, turn off the power before timer recording starts.
To lock the VCR
When the VCR is turned on, hold down ?/1 POWER on the VCR until the indicator appears in the display window. The VCR turns off and the - indicator
remains lit. The VCR will not work except for timer recordings.
To unlock the VCR
Hold down ?/1 POWER on the VCR until the - indicator disappears from the
display window. The VCR is unlocked and turns on.
To stop timer recording while the VCR is locked, press x STOP. The recording
stops and the VCR is unlocked.
Note
• The VCR will be unlocked when:
– You stop timer recording by pressing x STOP.
– You insert a tape.
– The AC power cord is disconnected or power supply stops.
Recording TV programs using the timer
45
46
Locking the VCR (Child Lock)
Additional Operations
Tip
• Adjust the picture using the TRACKING +/– buttons if:
– Streaks appear while playing in slow motion.
– The picture shakes during pause.
To set tracking to the center position, press both buttons (+/–) at the same time.
Playing/searching at various speeds
0
Notes
• The sound is muted during these operations.
• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but the
picture quality cannot be guaranteed.
• The picture may show noise when playing at high speed in reverse.
x2
y SLOW
M FF
H PLAY
M FF
m REW
m REW
TRACKING +/–
Playback options
Operation
View the picture during fastforward or rewind
During fast-forward, hold down M FF. During rewind, hold down
m REW.
Play at high speed
• During playback, briefly press M FF or m REW on the remote
commander. The tape continues to play at high speed.
• During playback, hold down M FF or m REW. When you
release the button, normal playback resumes.
Play at twice the normal speed
During playback, press ×2.
Play in slow motion
During playback or pause, press y SLOW.
Play frame by frame
During pause, press M FF or m REW on the remote commander.
Hold down the button to play one frame each second.
Rewind and start play
While the tape is stopped, hold down m REW on the VCR and press
H PLAY on the VCR.
To resume normal playback
Press H PLAY.
continued
Playing/searching at various speeds
47
48
1-11
Playing/searching at various speeds
Setting the recording duration time
Checking/changing/canceling timer
settings
After you have started recording, you can
have the VCR stop recording automatically
after a specified duration.
Before you start…
• Turn on your TV and set it to the video
channel.
z REC
?/1
TIMER
1
2
3
4
5
6
7
8
9
0
1 While recording, press z REC.
The
indicator appears in the display window.
VIDEO APC
SP
CLEAR
MENU
z REC repeatedly to set the duration time.
2 Press
Each press advances the time in increments of 30 minutes.
0:30
5:30
1:00
6:00
Normal recording
M/m/</,
OK
The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.
To extend the duration
Press z REC repeatedly to set a new duration time.
To cancel the duration
Press z REC repeatedly until the
normal recording mode.
indicator disappears and the VCR returns to
1 Press ?/1 to turn on the VCR.
TIMER to display PROG./VERIF.
2 Press
• If you want to change a setting, go on to the next step.
To stop while recording
Press x STOP.
• If you do not need to change the settings, press MENU, then turn off the VCR
to return to recording standby.
Note
• You cannot display the current tape time in the display window when setting the recording
duration time.
Setting the recording duration time
M/m to highlight the setting you want to
3 Press
change or cancel.
• To change the setting, press OK and press </
, to highlight the item you want to change,
then press M/m to reset it.
• To cancel the setting, press CLEAR.
49
50
Checking/changing/canceling timer settings
PROG. / VERIF.
Recording stereo and bilingual programs
(SLV-LX70S and LX60S only)
2 8 / 9 VIE
FECHA
COM.
TER.
3 0 / 9 DOM 8 : 0 0 PM 9 : 0 0 PM
2 / 1 0 MAR 1 0 : 0 0 AM 1 1 : 3 0 AM
LUN – VIE
2 : 0 0 PM 3 : 0 0 PM
CADA MER
6 : 3 0 AM 7 : 0 0 AM
–– / –
– : ––
– : ––
–– / –
– : ––
– : ––
–– / –
– : ––
– : ––
–– / –
– : ––
– : ––
VOLVER
SELECCIONAR :
CANCELAR
AJUSTAR
: OK
PARA SALIR
: MENU
CH
35
20
60
42
––
––
––
––
SP
EP
EP
EP
––
––
––
––
Recording stereo programs
: CLEAR
This VCR automatically receives and records stereo programs. When a stereo
program is received, the STEREO indicator lights up. If there is noise in the stereo
program, set ESTEREO AUTO. in the OPCIONES menu to NO. The sound will be
recorded in monaural (on both hi-fi and normal audio tracks) but with less noise. For
details, see page 62.
4
MENU to exit the menu.
5 Press
If any timer settings remain, turn off the VCR to return to recording standby.
Press OK.
Recording bilingual programs
When the timer settings overlap
The program that starts first has priority and the second program starts recording only
after the first program has finished. If the programs start at the same time, the
program listed first in the menu has priority.
Normally, this VCR records only the main sound. When a SAP (Second Audio
Program) is received, the SAP indicator lights up. To record only SAP sound, set
SINTONIZ. AUDIO in the OPCIONES menu to SAP. For details, see page 62.
Program 1
Selecting the sound during playback
Press AUDIO MONITOR to select the sound you want.
Program 2
Will be cut off
Tip
• To show the PROG./VERIF. menu, you can also use the MENU button. Press MENU, then
press M/m to highlight PROG./VERIF. and press OK.
Checking/changing/canceling timer settings
51
52
1-12
To listen to
On-screen display
Display window
Stereo
ESTEREO
STEREO
Left channel
L
STEREO
Right channel
R
STEREO
Monaural sound on the
normal audio track
No indicator
No indicator
Recording stereo and bilingual programs (SLV-LX70S and LX60S only)
How sound is recorded on a video tape
Searching for the beginning of a timer
recorded program
The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the
main track along with the picture. Monaural sound is recorded onto the normal audio
track along the edge of the tape.
Monaural sound
If you record a program using the timer
function, you can easily find the beginning of
the recording with this SEARCH MODE
function. The SEARCH MODE button lights
up when the VCR finishes a timer recording
and the display window shows the
following:
Normal audio track
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
DIAL TIMER
SEARCH MODE
Notes
• To play a tape in stereo, you must use the A/V connections.
• When you play a tape recorded in monaural, the sound is heard in monaural regardless of the
AUDIO MONITOR setting.
Press DIAL TIMER.
The VCR turns on, rewinds to the beginning of the most recently recorded program
and starts playback automatically. The SEARCH MODE button turns off.
Tip
• To turn off the SEARCH MODE button, first turn the VCR on, then press the
SEARCH MODE button. (Do not press any other button at this point, otherwise
this SEARCH MODE function will be canceled.) To start the SEARCH MODE
function, press the SEARCH MODE button once. If you press the SEARCH
MODE button repeatedly, you can enter the index search or Time Search mode (for
details, see page 55 and 56).
Notes
• This SEARCH MODE function will be canceled (the SEARCH MODE button
turns off) if:
– The VCR starts recording other programs.
– You press H PLAY, M FF, m REW, or A EJECT button while the VCR is on.
– If there is a power failure.
Recording stereo and bilingual programs (SLV-LX70S and LX60S only)
53
54
Searching for the beginning of a timer recorded program
Searching using the index function
Searching using the Time Search function
The VCR marks the tape with an index signal
at the point where each recording begins.
Use these signals as references to find a
specific recording. The VCR can search up
to 9 index signals ahead of or behind the
current position.
You can easily find a specific point on a tape
by using the Time Search function.
For example, you can find a recorded portion
15 minutes ahead of or behind the current
position of a tape by using the Time Search
function.
DIAL TIMER
DIAL TIMER
SEARCH MODE
SEARCH MODE
SEARCH MODE on the VCR repeatedly until “INDEX” appears in the
1 Press
display window (the SEARCH MODE button lights up).
SEARCH MODE repeatedly until “TIME” appears in the display window
1 Press
(the SEARCH MODE button lights up).
APC
APC
SP
SP
DIAL TIMER to specify how many index signals ahead or behind you want
2 Turn
to search:
DIAL TIMER clockwise or counterclockwise to set the length of the time
2 Turn
portion you want the VCR to fast-forward or rewind the tape. Each turn on the
control increases or decreases the duration by 15 minutes.
• To search ahead, turn DIAL TIMER clockwise.
• To search backwards, turn DIAL TIMER counterclockwise.
For example, if you want to watch a recorded portion 15 minutes ahead of the
current position, turn DIAL TIMER once clockwise.
APC
SP
To change the time by one minute,
press CHANNEL +/–.
DIAL TIMER.
3 Press
The VCR starts searching. The playback starts (the SEARCH MODE button
APC
SP
DIAL TIMER.
3 Press
The VCR starts searching and the tape counter starts counting until it reaches the
turns off) from the point about five seconds ahead of the specified index mark.
specified point.
To stop searching
Press x STOP.
APC
SP
Note
• No index signal will be added when recording starts from recording pause.
However, an index signal will be marked if you change the channel during
recording pause.
The VCR starts playback automatically when the tape counter reaches the
specified point (the SEARCH MODE button turns off).
To stop searching
Press x STOP.
Tip
• The VCR can search up to six hours ahead of or behind the current position of a
tape.
Searching using the index function
55
56
1-13
Searching using the Time Search function
Searching using the index function
Searching using the Time Search function
The VCR marks the tape with an index signal
at the point where each recording begins.
Use these signals as references to find a
specific recording. The VCR can search up
to 9 index signals ahead of or behind the
current position.
You can easily find a specific point on a tape
by using the Time Search function.
For example, you can find a recorded portion
15 minutes ahead of or behind the current
position of a tape by using the Time Search
function.
DIAL TIMER
DIAL TIMER
SEARCH MODE
SEARCH MODE
SEARCH MODE on the VCR repeatedly until “INDEX” appears in the
1 Press
display window (the SEARCH MODE button lights up).
SEARCH MODE repeatedly until “TIME” appears in the display window
1 Press
(the SEARCH MODE button lights up).
APC
APC
SP
SP
DIAL TIMER to specify how many index signals ahead or behind you want
2 Turn
to search:
DIAL TIMER clockwise or counterclockwise to set the length of the time
2 Turn
portion you want the VCR to fast-forward or rewind the tape. Each turn on the
control increases or decreases the duration by 15 minutes.
• To search ahead, turn DIAL TIMER clockwise.
• To search backwards, turn DIAL TIMER counterclockwise.
For example, if you want to watch a recorded portion 15 minutes ahead of the
current position, turn DIAL TIMER once clockwise.
APC
SP
To change the time by one minute,
press CHANNEL +/–.
DIAL TIMER.
3 Press
The VCR starts searching. The playback starts (the SEARCH MODE button
APC
SP
DIAL TIMER.
3 Press
The VCR starts searching and the tape counter starts counting until it reaches the
turns off) from the point about five seconds ahead of the specified index mark.
specified point.
To stop searching
Press x STOP.
APC
SP
Note
• No index signal will be added when recording starts from recording pause.
However, an index signal will be marked if you change the channel during
recording pause.
The VCR starts playback automatically when the tape counter reaches the
specified point (the SEARCH MODE button turns off).
To stop searching
Press x STOP.
Tip
• The VCR can search up to six hours ahead of or behind the current position of a
tape.
Searching using the index function
55
56
Searching using the Time Search function
Skip-searching automatically (Quick View)
Searching for a selected point on the tape
You can spot check an entire tape quickly
using the Quick View function. At intervals,
the VCR skips playback while searching
forward or backward.
You can easily find a specific point by
moving the pointer on the TV screen.
The VCR fast-forwards or rewinds to the
point you indicate and starts playback
automatically.
DISPLAY
M FF
1
2
3
4
5
6
7
8
9
0
m REW
Hold down M FF (or m REW) more than two
seconds during stop. “SKIP” indicator appears on the
TV screen.
SKIP
</,
The VCR searches forward (or backward) for about
two minutes on the counter while showing the
contents of the tape. Then it fast-forwards (or rewinds)
for about ten minutes on the counter. The VCR
repeats this operation until it stops at the end (or
beginning) of the tape.
search forward while
showing the tape contents
M fast-forward
DISPLAY repeatedly until the bar
1 Press
indication appears on the TV screen.
search forward while
showing the tape contents
A cursor (x) indicating the current position of
the tape appears on the bar indication. If the
cursor does not appear, play the tape a few
moments (by pressing H PLAY, M FF, or
m REW) until the cursor appears.
M fast-forward
0
120
0
120
</, to move the pointer (V) to the point
2 Press
where you want to start playback.
To cancel skip-search
Press H PLAY or x STOP.
The VCR starts searching and the cursor (x)
moves toward the pointer. When the VCR locates
the marked point, playback starts.
Note
• The VCR automatically fast-forwards (or rewinds) any portion with no recording.
Skip-searching automatically (Quick View)
57
58
1-14
Searching for a selected point on the tape
To cancel searching
Press H PLAY or x STOP.
Adjusting the picture
To turn off the bar indication
Press DISPLAY again.
Adjusting the tracking
Although the VCR automatically adjusts the tracking
when playing a tape (the
indicator flashes in the
display window, then turns off), distortion may occur
if the recording is in poor condition. In this case,
manually adjust the tracking.
Notes
• The figure on the bar indication represents the total time length of the inserted tape as shown
below.
The total time length may not be displayed correctly for:
– Tapes other than T-60, T-120, or T-160.
– Tapes recorded in more than one tape speed mode.
Press TRACKING +/– to display the tracking meter.
The distortion should disappear as you press one of
the two tracking buttons (the
indicator lights up).
To resume automatic tracking adjustment, eject the
tape and reinsert it.
Total time length
Tape type
SEGUIMIENTO NORMAL
Tracking meter
SP
LP
EP
T-60 or shorter
60
120
180
from T-80 to T-140
120
240
360
About the Reality Regenerator function
T-160 or longer
160
320
480
The Reality Regenerator function automatically restores the picture to its original
quality during playback.
• If you move the pointer (V) on the bar indication while searching, the VCR searches for the
new reset point.
• With the bar indication on, the M FF/ , and m REW/ < buttons on the remote
commander work only for moving the pointer (V) and are not used for normal tape operation.
The M FF and m REW buttons on the VCR are used for normal tape operation. Note,
however, if you press these buttons on the VCR, searching is canceled.
To use the Reality Regenerator function
1 Press MENU, then select OPCIONES and press OK.
2 Press M/m to highlight PRÓXIMA, then press OK.
M/m to highlight REALITY REGENERATOR on PÁGINA2 of the
3 Press
OPCIONES menu, then press OK.
OPCIONES
PÁGINA 2
APC
REALITY REGENERATOR
SENSR CONDCIÓN CABEZA
NITIDEZ
SI
NO
ANTERIOR
VOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
M/m to set REALITY REGENERATOR to SI, then press OK.
4 Press
The RR indicator lights up in the display window.
5 Press MENU to return to the original screen.
To turn it off, select NO in step 4. The RR indicator turns off in the display window.
Searching for a selected point on the tape
59
60
Adjusting the picture
About the Adaptive Picture Control (APC) function
Changing menu options
The Adaptive Picture Control (APC) function automatically improves recording and
playback quality by adjusting the VCR to the condition of the video heads and tape.
To maintain better picture quality, we recommend that you set APC to SI on
PÁGINA2 of the OPCIONES menu (The APC indicator lights up in the display
window). For details, see page 63.
1 Press MENU, then select OPCIONES and press OK.
OPCIONES
APC playback
The APC function automatically works on all types of tapes, including rental tapes
and tapes that were not recorded with APC.
SI
SI
MAIN
AUTO
SI
SELECCIONAR
AJUSTAR
PARA SALIR
PÁGINA 2
APC
REALITY REGENERATOR
SENSR CONDCIÓN CABEZA
NITIDEZ
SI
SI
SI
B
A
ANTERIOR
VOLVER
PRÓXIMA
VOLVER
APC recording
Whenever you insert a tape and first start recording, the VCR adjusts to the tape using
the APC function (the APC indicator flashes rapidly). This adjustment is retained
until the tape is ejected.
:
: OK
: MENU
SELECCIONAR
AJUSTAR
PARA SALIR
:
: OK
: MENU
Press M/m to highlight the option to change, then press OK.
2 To go to PÁGINA2, highlight PRÓXIMA and press OK. To return to PÁGINA1,
highlight ANTERIOR and press OK.
M/m to change the setting, then press OK.
3 Press
To adjust the sharpness, press </, and press OK.
4 Press MENU to return to the original screen.
Notes
• The auto tracking adjustment cannot be guaranteed to work with tapes recorded in the LP
mode on other VCRs.
• The APC function does not work if the tape speed is automatically changed from the SP to
EP mode during a timer recording when VEL. AUTO. CINTA is set to SI in the OPCIONES
menu, unless the tape has been recorded in the EP mode with the APC function.
• There is a delay of about ten seconds before the VCR actually starts recording while the VCR
analyzes the tape. To avoid the delay, first set the VCR to recording pause (the APC indicator
flashes slowly) and press z REC to have the VCR analyze the tape (the APC indicator
flashes rapidly) and return to recording pause. After the APC indicator stops flashing, press
X PAUSE to start recording immediately.
If you want to start recording quickly without using the APC function, first set the VCR to
recording pause (the APC indicator flashes slowly) and press X PAUSE again to start
recording.
Adjusting the picture
OPCIONES
PÁGINA 1
SELEC. AUTO. ANT.
ESTEREO AUTO.
SINTONIZ. AUDIO
SELC. DE CINTA
VEL. AUTO. CINTA
Menu choices
Initial settings are indicated in bold print.
PÁGINA1
61
62
1-15
Menu option
Set this option to
SELEC. AUTO. ANT.
• SI if your TV is connected only to VHF/UHF OUT on the
VCR. To play a tape, set the TV to the VCR channel (channel
3 or 4).
• NO if your TV is connected to both VHF/UHF OUT and LINE
OUT on the VCR. To play a tape, set the TV to the VCR input.
ESTEREO AUTO.
(SLV-LX70S and
LX60S only)
• SI to receive stereo programs.
• NO to reduce noise. The sound changes to monaural.
SINTONIZ. AUDIO
(SLV-LX70S and
LX60S only)
• MAIN to record the main sound on both hi-fi and normal audio
tracks.
• SAP to record the SAP (Second Audio Program) sound on both
hi-fi and normal audio tracks.
SELC. DE CINTA
• AUTO when using a T-160 length tape or any tape shorter than
a T-140 length tape.
• 180 when using a T-140 or T-180 length tape.
For details, see page 36.
VEL. AUTO. CINTA
• SI to change the timer recording tape speed automatically to
the EP mode when the remaining tape length becomes shorter
than the recording time. To operate VEL. AUTO. CINTA, set
SELC. DE CINTA correctly.
• NO to keep the same tape speed.
Changing menu options
PÁGINA2
Editing with another VCR
Menu option
Set this option to
APC
• SI to switch on the APC (Adaptive Picture Control) function
and improve picture quality.
• NO to switch off APC.
REALITY
REGENERATOR
• SI to switch on the Reality Regenerator (Reality Regenerator)
function and restore the picture to its original quality during
playback.
• NO to switch off Reality Regenerator.
SENSR CONDCIÓN
CABEZA
• SI to allow the VCR to automatically check the condition of
the video heads and inform you when they are dirty.
• NO to turn off the sensor.
NITIDEZ
• B (Low) through A (High) to adjust the sharpness of the
picture. Select B to turn off the sharpness control.
How to connect to record on this VCR
SLV-LX70S and LX60S
This VCR (Recorder)
TV
LINE-2 IN
Other VCR (Player)
LINE OUT
Audio/video cable (not supplied)
: Signal flow
SLV-LX50 and LX40
TV
This VCR (Recorder)
LINE-2 IN
Other VCR (Player)
LINE OUT
Audio/video cable (not supplied)
: Signal flow
Changing menu options
63
64
Editing with another VCR
Operation (when recording on this VCR)
Notes
• Make sure you connect the plugs to jacks of the same color.
• If you connected this VCR to both the LINE IN and LINE OUT jacks of the other VCR,
select the input correctly to prevent a humming noise.
• You can use the LINE-1 IN jacks for editing.
• If the other VCR is a monaural type and connected to this VCR’s LINE-2 IN jacks, connect
the audio plug to the AUDIO L (white) jack. The sound is recorded on both right and left
channels. If you connect to the AUDIO R (red) jack, the sound is recorded only on the right
channel. (SLV-LX70S and LX60S only)
• If the other VCR is a monaural type and connected to this VCR’s LINE-1 IN jacks, the sound
is recorded only on the channel whose jack is connected to the audio plug. To record on both
right and left channels, connect the audio plugs to the AUDIO R/L jacks using a VMC910HG audio/video cable (not supplied). (SLV-LX70S and LX60S only)
Before you start editing
• Turn on your TV and set it to the
video channel.
• Press INPUT SELECT or
CHANNEL +/– to display “L2” (or
“L1”) in the display window.
• Press SP/EP to select the tape speed,
SP or EP.
X PAUSE
z REC
1
2
3
4 To start editing, press the X PAUSE buttons on both VCRs at the same time.
Insert a source tape with its safety tab removed into the other (playback) VCR.
Search for the point to start playback and set it to playback pause.
Insert a tape into this (recording) VCR. Search for the point to start recording
and press X PAUSE.
Press z REC on this VCR to set it to recording pause.
To stop editing
Press the x STOP buttons on both VCRs.
Tip
• To cut out unwanted scenes while editing, press X PAUSE on this VCR when an unwanted
scene begins. When it ends, press X PAUSE again to resume recording.
Note
• If you start recording following the procedure above, the VCR won’t start recording with the
APC function. To record a tape with the APC function, press z REC again during recording
pause in step 3 so that the VCR analyzes the tape. Then, press X PAUSE after the APC
indicator stops flashing to start recording. If you press X PAUSE before the APC indicator
stops flashing, the APC function is canceled.
continued
Editing with another VCR
65
66
1-16
Editing with another VCR
Additional Information
Attaching the external antenna connector
General setup information
When using a 300-ohm twin lead cable for a
VHF/UHF antenna, use the EAC-32 antenna
connector (not supplied) to connect the
antenna to the VCR.
Setting the RF unit
When connecting the VCR to the TV using
only the antenna cable, you must set the RF
UNIT switch on the rear of the VCR so that
the TV can receive the correct signal from
the VCR.
300-ohm twin
lead cable
EAC-32 antenna
connector (not
supplied)
TV/VIDEO
1 Loosen the screws on the antenna connector.
2 Wind the twin leads around the screws on the antenna connector.
3 Retighten the screws.
TV
RF UNIT
CH3 CH4
1
2
3
4
5
6
7
8
9
Attaching a UHF/VHF band mixer
0
When using both a 75-ohm coaxial cable and
a 300-ohm twin lead cable for a VHF/UHF
antenna, use the EAC-66 UHF/VHF band
separator/mixer (not supplied) to connect the
antenna to the VCR.
300-ohm twin
lead cable
EAC-66
UHF/VHF
band
separator/
mixer (not
supplied)
?/1 POWER CHANNEL +/–
the RF UNIT switch on the rear of the VCR to CH3 or CH4, whichever
1 Set
channel is not used in your area. If both are used, set the switch to either channel.
Press ?/1 POWER to turn on the VCR.
2
3 Press TV/VIDEO to turn on the VIDEO indicator in the VCR’s display window.
CHANNEL +/– to display a channel number in the display window.
4 Press
Select an active channel number in your area.
on your TV and set it to the channel you selected in step 1 (channel 3 or 4).
5 Turn
The channel you selected in step 4 appears on the TV screen. If the channels
75-ohm coaxial
cable
1 Loosen the screws on the mixer.
2 Wind the twin leads around the screws on the mixer.
3 Retighten the screws.
4 Connect the 75-ohm coaxial cable to the mixer.
change when you press CHANNEL +/–, you have made the correct setting.
Whenever you use the VCR, set the TV to the channel selected in step 1.
continued
General setup information
67
68
Index to parts and controls
Symptoms caused by contaminated video heads
• Normal picture
• Rough picture
• Unclear picture
General setup information
• No picture (or
black & white
screen appears)
Refer to the pages indicated in parentheses ( ) for details.
Front panel
SLV-LX70S and LX60S
initial
contamination
terminal
Head Condition Sensor
The Head Condition Sensor checks the video heads’ condition. If the heads are dirty, a message
will instruct you to insert a video head cleaning cassette.
Be sure to use the Sony T-25CLD or T-25CLDR video head cleaning cassette. If these cleaning
cassettes are not available in your area, have the heads cleaned at your nearest Sony service
facility (a standard service charge will be required).
Note
• SENSR CONDCIÓN CABEZA in OPCIONES must be set to SI for the Head Condition
Sensor to operate.
• To turn off the head condition sensor message, set SENSR CONDCIÓN CABEZA to NO.
A ?/1 POWER switch (44)
I x STOP button (33) (66)
B Z EJECT button (33)
J X PAUSE button (33) (66)
C Tape compartment
K DIAL TIMER (38) (54) (55) (56)
D Remote sensor (5)
L SEARCH MODE button (54) (55) (56)
E m REW (rewind) button (33) (47)
M CHANNEL/TRACKING +/– buttons
(36) (60)
F H PLAY button (33) (47)
G M FF (fast-forward) button (33) (47)
H z REC (record) button (36) (49) (66)
N EASY SET UP button (11) (13) (16)
O LINE-2 IN VIDEO/AUDIO L/R jacks
(64)
continued
Troubleshooting
71
Index to parts and controls
1-17
73
SLV-LX50 and LX40
Display window
STEREO
VIDEO APC
SAP LP SP
EP
RR
A ?/1 POWER switch (44)
I x STOP button (33) (66)
A Timer indicator (40) (44)
G RR (Reality Regenerator) indicator (60)
B Z EJECT button (33)
J X PAUSE button (33) (66)
H Tracking indicator (60)
C Tape compartment
K DIAL TIMER (38) (54) (55) (56)
B SAP (Second Audio Program) indicator
(52) (SLV-LX70S and LX60S only)
D Remote sensor (5)
L SEARCH MODE button (54) (55) (56)
C STEREO indicator (52) (SLV-LX70S
and LX60S only)
E m REW (rewind) button (33) (47)
M CHANNEL/TRACKING +/– buttons
(36) (60)
D Tape speed indicator (36)
F H PLAY button (33) (47)
G M FF (fast-forward) button (33) (47)
H z REC (record) button (36) (49) (66)
J Time counter/clock/line/channel
indicator (33) (36) (66)
K Tape/recording indicator (36)
E VIDEO indicator (37) (67)
N EASY SET UP button (11) (13) (16)
I Child lock indicator (46)
F APC (Adaptive Picture Control)
indicator (61)
O LINE-2 IN VIDEO/AUDIO jacks (64)
continued
74
Index to parts and controls
Index to parts and controls
Rear panel
75
A •TV / VIDEO switch (5)
Remote commander
B Z EJECT button (33)
SLV-LX70S and LX60S
C TRINITRON TV SYNCHRO PLAY
button (34)
D DISPLAY button (36) (58)
E VOL (volume) +/– buttons (6)
F INPUT SELECT button (37) (66)
1
2
3
G z REC (record) button (36) (49)
4
5
6
7
8
9
H SP (Standard Play)/EP (Extended Play)
button (36)
0
A AC power cord (7)
D VHF/UHF IN connector (10) (12) (15)
B LINE-1 IN AUDIO R/L/VIDEO jacks
(65)
E VHF/UHF OUT connector (10) (12) (15)
C RF (Radio Frequency) UNIT switch (67)
I MENU button (18) (62)
J X PAUSE/M button (18) (33)
x STOP/m button (18) (33)
m REW (rewind)/ < button (33) (47)
M FF (fast-forward)/ , button (33)
(47)
H PLAY/OK button (18) (33)
F LINE OUT AUDIO R/L/VIDEO jacks
(8)
SLV-LX50 and LX40
A AC power cord (7)
D VHF/UHF IN connector (10) (12) (15)
B LINE-1 IN AUDIO/VIDEO jacks (65)
E VHF/UHF OUT connector (10) (12) (15)
C RF (Radio Frequency) UNIT switch (67)
F LINE OUT AUDIO/VIDEO jacks (9)
continued
76
Index to parts and controls
Index to parts and controls
1-18
77
K ?/1 (power) switch (6) (44)
L TV/VIDEO button (6) (37)
M AUDIO MONITOR button (52)
(SLV-LX70S and LX60S only)
N TIMER button (43) (50)
O Number buttons (31)
P ENTER button (31)
1
2
3
4
5
6
7
8
9
0
Q CH (channel) +/– buttons (6) (36)
R CLEAR button (33) (51)
S y SLOW button (47)
T ×2 button (47)
U REPLAY button (33)
78
Index to parts and controls
1-19E
1-19
SLV-LX40/LX50/LX60S/LX70S
SECTION 2
DISASSEMBLY
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. CASE, FRONT PANEL BLOCK ASSEMBLY
1 Two tapping screws
3 Upper case
4 Flat Cable FFJ-4
2 Two tapping screws
Hooks
5 Flat Cable FDM-10
Hooks
Hooks
Hooks
6 Front panel
(Engaged by the six hooks)
2-2. DI-80 BOARD, FJ-32 BOARD
5 FJ-32 board
6 Flat Cable FFJ-4
4 Two screws
(B2.6 x 8)
1 Two screws
(B2.6 x 8)
2 DI-80 board
3 Flat Cable FDM-10
2-1
2-3. REAR PANEL
2 Rear panel
(Engaged by the seven hooks)
Hooks
Hooks
Hooks
Hooks
1 POWER code stopper
2-4. MA-405 BOARD
1 Six screws
(Sumitite (B3) +BV)
2 MA-405 board with
mechanism deck
2-2
2-5. MECHANSIM DECK
4 Flat cable FMD-21
3 Flat cableFAC-9
5 Harness FE-127
6 Two screws
(BVTP 3 x 12)
9 Screw
(BVTP 3 x 12)
2 Screw
(Sumitite (B3), +BV)
qs Mechanism deck
1 Flexible cable
(CN260)
(CN101)
(CN351)
(CN350)
(CN600)
qa MA-405 board
0 MD base (R)
7 MD base (M)
8 MD base (R)
2-3
2-6. INTERNAL VIEWS
— Top View —
M901
Drum Assembly
DZH-0A0A/Z-RP
(LX60S/LX70S)
DZH-0A2A/Z-RP
(LX40/LX50)
8-839-047-53
ACE head block assembly
A-6759-620-A
8-839-049-53
Pinch press block assembly
A-6759-863-B
FE head
1-500-477-11
Reel (S) table
3-977-507-01
FL complete assembly
A-6759-619-B
Reel (T) table
3-977-508-01
— Bottom View —
M902
DC motor (capstan)
1-698-971-11
Rubber belt
3-977-510-01
M903
Cam motor assembly
X-3947-577-1
2-4
2-7. CIRCUIT BOARDS LOCATION
(
(POWER, EJECT SWITCH)
MA-405
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER, POWER SUPPLY
FJ-32 (LINE 2 IN)
DI-80 (DIAL TIMER)
2-5E
2-5
)
SLV-LX40/LX50/LX60S/LX70S
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
3-1
3-2
SLV-LX40/LX50/LX60S/LX70S
3-2. VIDEO BLOCK DIAGRAM
3-3
3-4
SLV-LX40/LX50/LX60S/LX70S
3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM
3-5
3-6
SLV-LX40/LX50/LX60S/LX70S
3-4. TUNER BLOCK DIAGRAM
LX40/LX50
3-7
3-8
SLV-LX40/LX50/LX60S/LX70S
3-5. AUDIO BLOCK DIAGRAM
3-9
3-10
SLV-LX40/LX50/LX60S/LX70S
3-6. POWER BLOCK DIAGRAM
3-11
3-12E
SLV-LX40/LX50/LX60S/LX70S
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
(For printed wiring boards)
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
Transistor
Diode
C
B
E
6 5 4
4 5 6
4
1 2 3
3 2 1
3 2 1
5
1
3
2
5 4 3
2
3
1
2
3
1
2
1
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µµF.
50V or less are not indicated except for electrolytics and
tantalums.
• Chip resistors are 1/10W unless otherwise noted.
kΩ=1000Ω, MΩ=1000kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name
XEDIT → EDIT PB/XREC → PB/REC
•
: non flammable resistor
•
•
•
•
•
•
•
•
•
•
: fusible resistor
: panel designation
: internal component.
: B+ Line.
B+
: B– Line.
B–
Circled numbers refer to waveforms.
Readings are taken with a color-bar signal input.
Voltage are dc between ground and measurement points.
Readings are taken with a digital multimeter (DC10MΩ).
Voltage variations may be noted due to normal production
tolerances.
•
: adjustment for repair.
• Circled numbers refer to waveforms.
When indicating parts by reference
number, please include the board name.
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
4-1
SLV-LX40/LX50/LX60S/LX70S
4-1. FRAME SCHEMATIC DIAGRAM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
E
F
G
H
I
J
FRAME SCHEMATIC DIAGRAM
4-3
4-4
SLV-LX40/LX50/LX60S/LX70S
MA-405 (VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER) PRINTED WIRING BOARD
— Ref. No. MA-405 Board:1,000 Series —
MA-405 BOARD
D101
D102
D103
D161
D162
D163
D189
D301
D302
D351
D352
D420
D421
D561
D562
D563
D600
D601
D602
D603
D604
D605
D607
D608
D609
D611
D612
D613
D621
D623
D625
D660
D661
D666
D702
H5
H9
F7
G8
G8
F13
F13
A11
A7
D9
D9
I5
J4
B4
B4
B4
B2
E2
C3
D3
E2
C5
D3
F2
F2
F2
F1
F1
C2
C1
D1
H3
I3
H3
C12
IC101
IC160
IC161
IC162
IC201
I4
H10
H12
H13
D6
There are few cases that the part printed on this diagram isn’t mounted in this model.
MA-405 BOARD (SIDE B)
IC260
IC301
IC350
IC403
IC404
IC570
IC600
IC601
IC660
C10
B9
B6
J5
I7
F9
D2
G1
I1
Q101
Q103
Q181
Q201
Q202
Q203
Q204
Q301
Q302
Q303
Q350
Q351
Q380
Q500
Q600
Q601
Q662
Q673
Q674
F11
F7
F3
C6
C5
E6
E7
A7
A7
A7
C8
D8
C7
H8
I1
I2
I2
I3
I2
CN101
CN103
CN104
CN182
CN260
CN270
CN351
CN358
CN402
CN600
CNJ562
G13
H6
I12
E3
B10
B11
D12
B6
I1
A2
B5
1
2
3
4
5
6
7
8
9
10
A
B
C
D
E
F
G
H
I
J
VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER
MA-405
4-6
11
12
13
SLV-LX40/LX50/LX60S/LX70S
MA-405 (REC/PB HEAD AMP) SCHEMATIC DIAGRAM
– Ref. No: MA-405 board; 1000 series –
• See page 4-21 for waveforms.
1
2
3
MA-405 BOARD(1/7)
REC/PB HEAD AMP(RP BLOCK)
A
XX MARK:NO MOUNT
4
5
6
7
8
9
10
11
12
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
13
CN270
4P
JL271
5
JL272
4
JL273
C285
0.01u
JL274
IC260
B+
3
D
AUDIO CH1 H
AUDIO REC
2
1
AUDIO CH2 L
3
2
1
JL266
R270
470
JL270
AUDIO CH1
C271
0.01u
B
C272
0.1u
B
12
H.SYNC
11
AGC
DET
13
R2.5/
P0
R1.6/P2.0
IC260
AN_GND
10
ATT
VCC
R273
R3.2/
P2.5
C283
0.01u
B
C281
0.01u B
R4.1/
P0
R3.4/
P0.4
0.60mm
JL279
R274 3900
JL280
R267
0
JL281
JL282
C282 B
0.01u
R3.4/
P0
1k
9
AGC
AMP
VCC
AN_GND
VA1
REC CURR ADJ
VA2
REC H
VA3
REC C
VA4
REC Y RF
VA5
PB RF
VS3
COMP SYNC
VA7
TRICK H
8
HA
SP
7
C284
0.22u B
6
R0/P2.6
JL284
R277
22k
0.3
JL286
1.8
JL287
RS1
RF ENV
VS6
RF SWP
VS7
HA SWP
RS2
ENV SW
2
MA-405 (3/7)
(SEE PAGE 4-11)
R278
22k
0
R0.2/P0.5
R279
22k
SW30
R2.0/P4.2
H
L
LA70011
C267
0.1u
B
3
B+
C286
100p
CH
C268
XX
SW_5V
AN_GND
AUDIO CH2
1
E
1
MA-405 (2/7)
(SEE PAGE 4-9)
R0/P1.6
5
15
R1.6/P2.0
JL268
JL269
16
R1.6/P2.0
JL267
JL278
4
4
JL262
4
CHECK
2
FE
4
5
R3.9/P2.0
RF SWP
1
AN_GND
5
JL263
PB OFF
SW30
AMP REC
SP OFF
EP OFF
EP
TO HA
H.SYNC
HA
ENVELOPE
CONT
DET
6
R2.5/
P0
C275
0.01u
B
PB RF
3
R276
6800
COMP
SP CH1 F
R3.8/
P2.0
BIAS
6
JL265
C276
0.1u
B
CURRENT
AMP
7
R271
470
BIAS
SP CH2 S
JL264
VCC
7
JL261
VCC
8
10k
SP CH2 F
AMP
9
8
CURRENT
AMP
10
EP CH1 F
17
EP CH2 S
9
PB OFF
REC
SP OFF
EP OFF
AMP 10k
SP CH1
10
JL260
20
C
11
R3.9/
P2.0
21
EP CH2 F
C278
0.022u
B
22
SP CH2
R1.4/P0
18
}0.5%
C279
0.1u B
CN260
11P
R4.2/
P4.9
19
R272
1800
ALL 5V
14
4.9
PB ON
REC OFF
EP CH1
23
6
JL277
3
L270
100uH
C280
100u
10V
HF ADJ
2
B+
VIDEO REC/PB AMP
24
B
1
3
EP CH2
11
14
MA-405 (7/7)
(SEE PAGE 4-19)
2
AU1 AUDIO CH2
LX60S/LX70S
AU2
AUDIO REC
AU3
AUDIO CH1
AN_GND
4
MA-405 (4/7)
(SEE PAGE 4-13)
AU_PB_RF
VIDEO HEAD
F
SIGNAL PATH
VIDEO SIGNAL
CHROMA
Y
Y/CHROMA
AUDIO
SIGNAL
(POWER, EJECT SWITCH)
(
MA-405
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER, POWER SUPPLY
)
REC
PB
FJ-32 (LINE 2 IN)
DI-80 (DIAL TIMER)
REC/PB HEAD AMP
4-7
4-8
MA-405(1/7)
SLV-LX40/LX50/LX60S/LX70S
MA-405 (Y/C, AUDIO PROCESSOR) SCHEMATIC DIAGRAM
– Ref. No: MA-405 board; 1000 series –
• See page 4-5 for printed wiring board.
• See page 4-21 for waveforms.
2
3
MA-405 BOARD(2/7)
Y/C, AUDIO PROCESSOR (VA BLOCK)
6
7
8
9
10
B+
C242
0.01u B
58
INV
AMP
P
84
OSD V OUT
C204 C205
1u
0.01u
B
B
C202
0.01u
B
3.7
1.3
R203
330
Q201
2SC2712Y-TE85L
BUFFER
D7
D8
R204
8200
R210
1500
C5
H
C574
10u
16V
1.8
R206
XX
5.0
16
15
14
13
12
11
REG
GND
SUB
SUB
SUB
SUB
35
34
33
JL209
32
3.0
C222
10u 16V
R576
100k
JS323
0.60mm
HV1
NORMAL_OUT
E7
9
24
25
26
27
R222
XX
R221 R220
0
0
C219
XX
C213
390p
28
29
HV2
NORMAL_IN
R219
100
AUDIO_R_OUT
30
3.4
23
0.3
22
1.8
21
0
20
HV4
AUDIO_L_OUT
HV5
11
L1_AUDIO_R
HV6
MAIN OFF
C576
100u
10V
JS324
0
C221
1u
B
D8
HT3
E8
C3
C217
0.022u
B
R211
4700
C216
1u
50V
R212
560
C2
C252
0.01u
C6
C4
C5
R2.4/
P2.1
C1
Y/C, AUDIO PROCESS
4-9
HM4
L2_AUDIO_L
RF_AUDIO_OUT
VS1
AUDIO_MUTE
VA1
REC CURR ADJ
VA2
REC H
VA3
REC C
VA4
REC Y RF
VA5
PB RF
R209
5600
R208
0
JL220
D7
HM5
JS325
0
FSC_FOR_ADJ
PB
JL217
9
MA-405(4/7)
(SEE PAGE 4-13)
L2_AUDIO_R
C220
0.01u
B
REC
JL218
L1_AUDIO_L
LX40/LX50
JL219
C575
0.01u
B
8
MA-405 (5/7)
(SEE PAGE 4-15)
HF_GND
E5
JL222
C573
0.33u
B
TU AU MONO
LX40/LX50
31
VIDEO
AGC
5.0
R571 R572
470
470
TU VIDEO IN
HT1
HT3 RF AUDIO
JS327
xx
VIDEO SIGNAL
10
VT2
JL368
E3
SIGNAL PATH
DATA
CLK
MONI 2
9
JL572
5.0
8
JL571
7
R570
10k
C572
4.7u
50V
L570
100uH
MONI 1
FIL ADJ
6
1.1
5
4.9
4
1.8
2.3
2.9
3
VCC
Y OUT
C OUT
IC570
JL570
2
JS321
xx
AN_GND
R1.8/
P1.4
IN
VS15 RF VIDEO
E1
C223
22u 16V
1.5
CHROMA
1
MA-405(2/7)
JL207
C224
0.1u B
R1.7/
P0
AFC
FILT
R0.1/P1.5
19
2.3
18
JL208
41
40
39
C225
1u 50V
10
4.6
17
SW GND
OUT
C226
0.1u B
R2.1/
P0
HV3
4.6
16
AGC
TC2
R
2.1
2.6
17
ARC
B+
2.4
1.9
1.8
2.8
4.1
18
Y IN
2.6
IC570
19
C IN
LA7277M-TLM
20
C228
C227 47u 16V
0.1u
C578 R574
0.01u
1k R573
B
8200 C577
0.01u
B
R575
4700
1.8
C571
1u
B
C570
0.01u
B
I
Q202
2SC2712Y-TE85L
BUFFER
L203
10uH
B+
R
P
15
R207
XX
VS15
J
14
C210
0.1u B
C251
0.1u C212
XX
B
VS13
CTL_Y
B
L
LX60S/LX70S
AUDIO
C231
47u 16V
JL206
C209
47u
16V
13
PB-H
3.0-3.7
12
3.1
11
C215
10p
CTL_X
C229
0.1u B
R3.2/
P1.3
VIDEO
R2.2/P0.3
SYNC
DET
JL204
10
Y GND
R3.1/
P2.5
VIDEO
PEAKING
9
R2.4/
P1.6
8
2.2
7
2.0
R201
330
C206
0.1u
B
R223
680
6
M-Em
FIL
R2.4/P1.6
JL203
5
1.1
4
C4
VIDEO OUT
3
Y-Vcc
N.L
FILT
2 3
1
6dB
AMP
R
SERIAL
DECODER
CLAMP
EQ
CTL
CLAMP
L204
100uH
D2
VS12
CLAMP
N.L
De-EM
DHP
NC
D4
VS11
FMAGC
DET
R0.8/P1.8
R0/
P2.5
2
Chara
INS.
CLAMP
P
SUB
LPF
D5
ARC CLK
ARC DATA
CNJ562
C3
VS8
Y/C
MIX
DETAIL
ENH
DEMOD
R205 100k
}0.5%
VS6
C ROT
R
SYNC
SEP
L202
100uH
1
C253
39p
R231
47k
R224
47k
D5
RF SW P
REG
R213
1k
C230
0.1u F
4.1
R
P
P
8
C211
33p
BAL
TC1
R202
I2C DATA(VIDEO) HS3
DOUBLE
LIM
PB
EQ
C6
6
S
5.0
ACC
DET
FILT
L207
220uH
D4
CLAMP
FBC
KIL
B.D.
N.L
EMPH
Main
EMPH
N
D2
JL215
R
P
PIC
CONT
SQPB
EQ
FM
AGC
JL213
I2C CLOCK(VIDEO) HS4
FM
MOD
R2.4/P2.0
TRICK-H
7
JL214
P
C232
1u B
5.0
1.8
REC
EQ
JL201
VS2
SW-Vcc
38
90
91
RF SWP
Q203
2SA1162Y-TE85L
BUFFER
C233
10u 16V
3.0
13
HASW
15
Q VD
R
FBC
IC201
LA71053M-MPB
VS1
P
ACC
AMP
92
C.ROT
12
A MUTE
B-UP
AMP
1/2
C214
180p
C201
0.047u
B
CLAMP
KIL
C208
0.01u B
R1.6/
P2.0
1
43
85
86
89
0.8
C1 4.2
F
VCA
R
L201
39uH
2
1.9
LPF
A MUTE
3.1
3
CTL (Y)
P
R
C-LPF
2.0
4
GND (AU)
CTL (X)
JL321
YNR
JL560
R
P
P
JL202
5
N.C
B+
C234
1u
B 2.1
4.9
REC
BGA
Main
CONV
Sub
BPF
C207
39p
A HEAD PB
60/50
R
2.0
A HEAD REC
BPF1
D561
RD8.2ES-T1B
1.4
C563
470u
10V
C564
XX
D562
XX
2.2
R564
68
R565
75
D563
XX
1.4
1H
D.L
R
R
REC-H
B
C235
0.1u B
9.0
2.0
0.8
R3.3/
P0.2
C363
4.7u
50V
JL322
Sub
COVN
R1.6/P1.7
6
C2
P
R
PB-LP.SP
820
7
GND (AU)
HEAD SWITCH
Y/C PROCESSOR
AUDIO PROCESSOR
C562
47u
25V
C561
0.01u
B
C236
0.01u
2.0
P
2.3
AERASE HEAD
JL323
JL305
R4.1/P0
P
PB
BGA-A
R561
330
3.1
EQ
AMP
2.6
ACE HEAD
0
R371
18k
IC350
REC
R2.4/
P0.3
CN350
7P
AU_GND
E
P
93
R367
R364
R365
5600 2.3
270
330k
C368
R366
R3.1/
0.01u
8200
P2.3
B
R369
C366
2.3
820 1u 50V
94
5
2.4
95
C362
47u
16V
R0.8/
P0
C365
0.01u
B
96
C364
10u 16V
97
6
ACC
AMP
PB
BGA-B
BPF2
98
7
4
2.4
8
3
AUTO
BIAS
2.4
99
2
R0.8/P0
B
REC
REC-EP.LP
PB-EP
100
BA7755AF-E2
1
Q350
2SC1815GR-TPE2
BIAS SWITCH
IC350
1
C361
XX
R1.6/
P5.0
CLK IN
LPF
RA
Vref
R0.6/P0
R1.6/P5.0
87
JL306
5.0
2
FE HEAD
C359
0.001u
R3.3/
P0.2
3
C360
2700p
R363
18k
R370
12k
0
GND (AU)
2.4
3.2
C237
0.01u
B
IC201
TH
88
C370
XX
CN351
3P
JL307
R362
1200
R563 R562
180
150
1/4W 1/4W
51
4Fsc
0.8
2.4
B+
52
1H/2H
D.L
D.L
EQ
REC
APC
53
49
REC
APC
54
R577
100k
ALC
R
LINE
AMP
A-GND
REC
APC
55
2.6
VCO
MUTE
2.5
2.5
56
48
VXO1
57
BUFFER
59
4.9
3.4
60
Q561
2SB709A-QRS-TX
61
4.9
C243
0.01u
3.3
3.3
62
50
63
N.C
47
64
3.3
3.4
65
4.9
C248
0.047u B
JL210
X201 3.579545MHz
66
L561
100uH
46
VXO2
KIL
DET
67
45
L1
68
L2(R)
HM5
C255
0.1u
B
44
69
N.C
AU_GND AU_GND
42
70
N.C
TU
REC
AMP
82
83
C358
1u 50V
71
MA-405(6/7)
(SEE PAGE 4-17)
B+
SLD
2.3
R359
4700
72
7
L2(L)
HM4
R225
680
37
R358
1800
73
N.C
L2
Vref
0
74
L2_VIDEO
L2_V
1.6
LX40/LX50
36
LX40/LX50
75
A-Vcc
E1
2.3
Q204
2SD601A-QRS-TX
C203
0.001u
CH
JL205
C380
0.047u
PET
76
C238
47u 16V
CCD GND
C
77
ALC
DET
R357
8200
C371
560p
78
5.0
C239
0.01u B
C240
47u
16V
C246
0.01u
R214
1500
C254
1u
B
LX60S/LX70S
AN_GND AN_GND
C245
1u
B
NTSC:H
BIAS OSCILLATOR
TRANSFORMER
R383
180
79
LX40/LX50
L205
100uH
L206
100uH
CCD VCC
80
R352
68k
1/4W
C350
1u
50V
C241
0.01u
B
C-Vcc
T380
C353
1u
3.8
C357
4.7u
50V
81
4
5
6
R372
560
MUTE
SWITCH
C355
1u
2.5
Q351
2SC2712Y-TE85L
16
2.2
8
7
C356
33u
25V
C250
0.047u
B
R215
8200
C247
0.022u
B
2.1
1/10W
C384
XX
0.60mm
JS303
R216
1800
JL211
R356
5600
R355
68k
1/4W
D352
1SS119-25TD
E3
E5
R354
2.2M
LX40/LX50
C249
1u
B
C-GND
1
D351
1SS119-25TD
1.9
C369
4.7u
C579
XX
14
C351 R351
47u 5600
R353 25V
R350
5600
68k
JL301
B+
JL320
C383
47u
16V
JS301
0.60mm
C244
1u
B
JL304
L380
100uH
C354
10u
16V
5.0
R380
47
R373
1k
1/4W
C352
0.1u
LX40/LX50
2.3
R381
3900
C382
0.01u
L350
XX
B+
2.3
C381
0.01u
JL302
R4.7/P5.0
R1.8
/P5.0
JL303
JL308
Q380
2SD1620-TD
BIAS OSC
3
B+
E7
E8
B
FE HEAD
14
R :REC MODE
P :PB MODE
B+
R1.7/P5.0
MA-405 (3/7)
(SEE PAGE 4-11)
13
B+
R382
1
G
12
B+
SW_5V
AU_GND
SW_12V
D
11
AN_GND
AN_GND
5
MA-405 (7/7)
(SEE PAGE 4-19)
5
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
2
A
4
HF_GND
1
4-10
Y
Y/CHROMA
AUDIO
SIGNAL
VS3
COMP SYNC
VA7
TRICK-H
1
MA-405 (1/7)
(SEE PAGE 4-7)
SLV-LX40/LX50/LX60S/LX70S
MA-405 (SERVO/SYSTEM CONTROL) SCHEMATIC DIAGRAM
– Ref. No: MA-405 board; 1000 series –
• See page 4-5 for printed wiring board.
• See page 4-21 for waveforms.
1
2
3
MA-405 BOARD(3/7)
SERVO/SYSTEM CONTROL (SS BLOCK)
A
4
5
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
6
7
8
9
10
11
12
13
14
R :REC MODE
P :PB MODE
OSD_VCC
JL110
D_GND
MTR_GND
10
AN_GND
MA-405 (7/7)
(SEE PAGE 4-19)
B+
B+
B+
B+
B+
B+
B+
B+
SW_5V
D_6V
SW_12V
MTR_12V
JL114
C146
2200p
B
R143
4700
JL111
CTL
P CONT M12 PS1
CTL_Y
6
CTL_X
MA-405 (2/7)
(SEE PAGE 4-9)
JL112
JS101
0.60mm
M2
M1
M7
B
M6
P CONT SW12 PS2
D109
D163 XX
MPG06D-6052PKG3
JS522
0.60mm
REMOCON MS1
M1
FUNC KEY1 MS2
S102
M2
FUNC KEY2 MS3
S CLK0 MS4
MA-405 (6/7)
(SEE PAGE 4-17)
S OUT0 MS6
B+
C143
22u
50V
M6
C142
0.022u
B
MODE2
JL116
MODE1
C186
XX
JL117
GND
C185
1u
S6
JL118
S7
JL120
29 R170
C164 C165 C168
24p 24p 100u
10V
B+
IN 2
VCL
VCH
V REF
VCC 1
VCC 2
CAM(+)
4
5
6
7
8
9
10
JS103
XX
JL123
JL106
SW 5V
1
2
CAP RVS
2
3
CAP FG
3
4
CTL-REF
4
5
CAP VS
5
6
LIMITER
JL104
6
7
MTR 12V
7
JL125
8
MTR_GND
8
9
AN_GND
9
1
CAM(-)
1
2
CAM(+)
2
3
CAM(+)
3
M
M902
CAPSTAN MOTOR
L101
2.2uH
T3
0
T2
R507
470
JL501
L501
100uH
R102
15k
PH102
GP3S120S
T.REEL FG
D101
XX
C102
0.001u
B
C510
0.1u
B
PH101
GP3S120S
S.REEL FG
C513
Q502
0.001u
2SA1162Y-TE85L
B
BUFFER
1.8
2.5 R513
470
1/4W
R512
0
C101
0.001u
B
R103
15k
R104
22k
4.9
C103
0.001u
B
13.5
REC PROOF
MA-405 (7/7)
(SEE PAGE 4-19)
S13
S15
R105
22k
1/4W
JL132
R101
470
1/4W
S16
B+
B+
C509
3900p
B
JL128
MTR_GND2
S101
JS161
0.60mm
5.0
1.8
10
MTR_GND2
S14
C508
1u
B
R508
1500
2.0
M
M903
LOADING MOTOR
R509
1M
C507 680p CH
JL101
C109
0.1u
B
C108
0.1u
B
S18
21
C504
0.001u
CH
C107
1u
F
C106
47u
16V
T4
0
CN103
3P
JL102
C110
XX
JL134
R502
0
M
M901
DRUM MOTOR
CN102
9P
1
S11
R118 R119
47k 15k
B+
V1
4.9
2.6
13.5
4.8
2.2
R121
470
M3
R187 0
2.0-3.1
JL130
4.9
1.9
1
0.2
IN 1
3
6.3
CAM(-)
2
0.2
1
JL142
0
MTR 12V
C189
XX
MTR GND
R188
6800
R189
3300
R192
1k
JL141
R185
0
R191
1k
JL140
0
2
1
LB1943N
3.1-3.9
R183
4.6
0
4.9
JL107
JL124
C192
XX
LOADING MOTOR DRIVE
C514
0.001u B
C511
0.1u F
C512
100u 10V
OSD GND
S9 R112 4700
R117
470
JL170
4.9
D VS
JL109
JL108
IC101
S10
JL139
4.9
3
2
R106
39
1/4W
R107
39
1/4W
4.9
C104
0.001u
B
1.6
C105
330u
6.3V
D102
XX
D103
GL528V1
T/S.LED
0.4
R111
2200
R120
1k
1/4W
Q103
2SC1815GR-TPE2
LED DRIVER
C502
0.01u
B
C500 C501
15p 15p
JS520
XX
C171
0.33
5.5V
JL500
B+
I
6
MA-405 (2/7)
(SEE PAGE 4-9)
L162
22uH
B+
ARC CLK VS11
C174
XX
JL129
SIGNAL PATH
REC
REC/PB
PB
DRUM SPEED SERVO
ARC DATA VS12
D161
MPG06D-6052PKG3
L161
22uH
MM1256XF-BE
4
1
6
3
2
VCC 1
WP
2
3
OUT 2
1
4
VCC 2
5.0
8
5
OUT 1
CLK
7
R178
220k
DATA
4.8
5.0
4.9
R504
1k
5
5.0
5.0
C162
0.1u
F
IC161
EEPROM
C505
10p
CH
R505
680
B+
DRUM PHASE SERVO
DRUM SERVO (SPEED AND PHASE)
CAPSTAN SPEED SERVO
R179 470k
4.8
JL186
C175
XX
R503
1k
6
JL185
JS163
0.60mm
M24C04-WMN6T
JL162
7
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
8
J
D162
MPG06D-6052PKG3
V7
V6
S11
3300
2.6
4
D PG
C187
1u
F
C188
1u
B
R109
47k
B+
2.7
5
D FG
3
S10
S5
19
OSD V IN
1.8
SP
LPF
NUB
OSC OUT
OSC IN
I2C CLK EEP
JL169
R195
0.60mm
S17
4.8
R123
XX
R110
47k
R190
0.60mm
0
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
R194
10k
0.1-4.9
JL126
0.1-4.9
JL122
MTR GND
4
C191
XX
C114
XX
S8
JL131
Q102
PT380F3
SUPPLY END SENSOR
WHITE LEVEL/ LECHA
REC PRF
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
DMS -
DMS +
1.4
2.3
2.3
5.0
4.9
5.0
OSD V OUT
MODE1
R193
0
H
OSD Vcc
C112
0.01u
B
S17
JL136
JL138
JL137
5.0
F MONO
MAIN/SAP
SAP
CAP FG
STEREO
AMP Vss
DRUM FG
DRUM PG
RC CHECK
AMP Vref IN
AMP Vref OUT
HLF
MODE2
R500 1k
4
VHOLD
MODE3
C503 4700p B
RESET
C VIDEO IN
R114
10k
R113
10k
S18
5
B+
PS101
ICP-N5
JL127
CN101 5P
JL119
C190
47u
16V
B+
Q101
PT380F3
TAKE END SENSOR
R177
470 1/4W
JL135
5.0
2.3
1/4W 470
R175
R176
470 1/4W
2.8
2.4
22u
C144 50V
R2.8/P2.4
MODE4
JL166
JL161
18 20
2.2uH
3
NUA
17
N.C
L500
2
CTL - IN
CAP RVS
R172
10k
1
S-CLK
CTL + IN
N.C
N.C
C163 0.047u B
D_GND
AMP C
AVcc
PLL CLK
5.0
S-DATA
AMP Vcc
AF REC P
CLK SEL
5.0
PLL DATA
R180 JL133
3300
S14
PLL ENABLE
ANT SEL
ARC DATA
0
S4
END LED
ARC CLK
G
NC
C169
0.1u
F
0
AF SWP
2.2
0
S3
A MUTE
2.1
S2
P CONT M12
RF SWP
Vss
T5
ENV SW
4fsc(out)
S1
FLD CS
P CONT SW12
SERVO SYSTEM
CONTROL
4fsc(in)
5.0
T4
HA SWP
JL164
S8
T3
IC160
C ROT
R174
C167
390
18p R510
0.60mm
R511
0.60mm
T2
V-SET CS
REMOCON
5.0
R0/P5.0
S IN0
S OUT0
QVD
1.4
2.5
S CLK0
KKP -
Vcc
2.5
5.0
(OPEN)
CAP ERR
KKP +
C166
15p
S13
T1
CN104
DRUM ERR
I2C CLK
32kHz(out)
V11
4P
P FAIL
26
X161
32.768kHz
X160
14.31818MHz
RS2
TS5
S REEL
CBC ON
1.5
ENV SW
TS4
T REEL
I2C DATA
32kHz(in)
2.5
TU AFT
24
CBC SIRCS OUT
JL163
VS7
PLL ENABLE
2.4
4.8
V11
HA SWP
TS3
AF ENV
4.8
0
0.6
TS2
V RF ENV
2.2
2.5
VS6
PLL DATA
JL115
S4
C116
0.01u
B
C115
0.01u
B
22
23
CLKOUT
RESET
V9
4.9
V4
RS1
PLL CLOCK
T SENS
CAM
0
RF ENV
TS1
S3
JL121
C111
0.01u
B
NICOLE
5.0
4.9
R0/
P5.0
RF SWP
TV/VTR
S9
25
28
5.0
LX60S/LX70S
V2
T1
13
S SENS
I2C DATA EEP
R164
47k
R165
47k
V7
R167
15k
1/4W
MA-405 (5/7)
(SEE PAGE 4-17)
FUNC KEY1
4.9
R0.1/P3.2
R166
10k
2
C170
680p
CH
R0/P2.5
R160
1k
V6
VIDEO OUT VS13
OSD V OUT VS15
MA-405 (1/7)
(SEE PAGE 4-7)
4.9
V4
C ROT VS8
F
S16
V9
R159
100k
V2
Q VD VS2
4.9
7
V1
A MUTE VS1
S15
8
6
C161
0.047u
B
9
C113
0.1u
B
RF SWP VS6
MA-405 (2/7)
(SEE PAGE 4-9)
S6
27
TU AFT
FUNC KEY2
4.9
I2C CLK HS4
I2C DATA HS3
CTL AMP OUT
V-SET RESET
4.7
E
MPX MODE
3
T5
DEST
0
C160
0.047u
B
MPX MODE HS7
1
LX60S/LX70S
2
R162
1500
1/4W
4
HS5
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
AF ENV
R161
10k
5
HS4
MODE3
R115
47k
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
6
I2C CLK
JS521
0
R169 10k
HS3
B+
I2C DATA
R116
47k
LX40/LX50
JL160
MA-405 (4/7)
(SEE PAGE 4-13)
HS2
R168 10k
12
HS1
AF SWP
2.4
R171
47k
R142
1200
L163
22uH
S5
S7
4.8
C141
0.1u
F
C145
470u
10V
R2.0/P2.4
C140
100u
10V
C176
0.1u
B
AF REC P
MODE4
JL105
R173
XX AN_GND
0.2
M7
4.8
KKP + MS11
2.4
D5V MS10
KKP - MS12
D
JL103
M3
FLD CS MS7
C
S1
S2
MTR_GND
11
C172
0.01u
B D_GND
C173
0.01u
B
C515
XX
2.5
1.5
CAPSTAN SERVO (SPEED AND PHASE)
Q500
2SB709A-QRS-TX
SERVO REF SIGNAL
IC162
POWER FAIL DET
RESET PULSE GEN
SERVO/SYSTEM CONTROL
4-11
4-12
MA-405(3/7)
SLV-LX40/LX50/LX60S/LX70S
MA-405 (AUDIO PROCESS) SCHEMATIC DIAGRAM
– Ref. No: MA-405 board; 1000 series –
• See page 4-5 for printed wiring board.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
MA-405 BOARD(4/7)
AUDIO PROCESS (AU BLOCK)
A
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
LX60S/LX70S
JL331
14
SIF
MA-405 (6/7)
(SEE PAGE 4-17)
AN_GND
JS302
B
JL325
JL326
JL327
SW_5V
B+
XX
B+
2.5
2.5
0.4-0.7
HF_GND
1.7
GND R
N.C.
VCC5V
REC ADJ
5.0
0-5
0-5
SCL
32
31
29
30
C334
0.22u
C335
XX
B
28
L
H
ENV
DET
0-5
SWP
58
VCC12V
RFC OUT
2.1
RPVCC5V
25
56
57
OUT L
OFF
PB IN1
INSW
MUTE
C337
0.01u
5.0
PNR Lch
EE
moniter
C336
0.1u
26
VCO L
MPX
MODE
27
OUT
SEL
R2.1/P0.7
ON
R/P GND
PB IN2
C338
0.01u
60
NA OUT
61
R2.1/P0.7
2.6
RFC AGC
REC OUT
R2.1/P0
20
C339
0.1u
AU_PB_RF
C340
0.015u
19
IN SEL
C341
10u
16V
0.4-0.7
2
VS1
HF_GND
IC301
H
AUDIO_REC
AU1
3
4
5
7
AFM
AUDIO PROCESS
ONLY LX60S/LX70S
8
9
10
11
12
R312
XX
13
R315
XX
14
15
R317
XX
4
MA-405 (1/7)
(SEE PAGE 4-7)
AUDIO_CH2
AN_GND
C342
10u
16V
JS304
16
2.5
1
L2 L
}10%
JL324
L1 L
*C316
3.3u
50V
0
JL319
C306
0.022u
0
R307
XX
JL318
GND L
6
JL316
INREF L
JL315
JL317
AUDIO_CH1
AU2
AN_GND
17
0.3
JL314
64
2.5
JL313
AU3
2.5
2.5
18
JL312
dbx
NR.
NA IN
63
R308
56k
C303
0.1u
62
2.5
2.2
AUDIO MUTE
+
ON
6
XX
24
GND
L2 R
HM4
2.2
49
51
{
L+R
REF
R334
5.0
L1 R
L2_AUDIO_L
R322
XX
FM
LIMITER
0
HM5
6
HS2 AF_SWP
33
NOISE
DET
0
L2_AUDIO_R
34
23
2.2
INREF R
HV6
35
1.8
BPF
2.2
HV5
L1-AUDIO_L
36
OUT R
VREF
L1_AUDIO_R
37
ON
INSW
MUTE
(L-R)/SAP
Switch
2.5
HV2
38
R2.1/P0
JL311
HV1
39
VCO R
6
12
FSC_FOR_ADJ
NORMAL_IN
40
HS5 AF_ENV
JL330
R323
0
VCC5V
59
C312
10u
50V
R306
220
JL310
NORMAL_OUT
41
22
R305
220
F
MA-405 (2/7)
(SEE PAGE 4-9)
12
MA-405 (3/7)
(SEE PAGE 4-11)
21
C310
10u
50V
C311
2.2u
50V
C313
10u
50V
C315
10u
50V
C314
10u
50V
HT3
42
SDA
2.2
C305
47u
25V
Q303
2SC2712Y-TE85L
MUTE
HV4
43
OFF
0.66
RF_AUDIO_OUT
44
OFF
52
C309
0.1u
R303
1k
AUDIO_L_OUT
45
PNR Rch
5
0.66
HV3
I2C_CLOCK
C333
0.1u
SAP DEMOD
50
C302
0.01u
HF_GND
53
E
R302
1k
Q302
2SC2712Y-TE85L
MUTE
46
C330
0.015u
0
54
1.5
D302
1SS119-25TD
Q301
2SA1162Y-TE85L
POWER MUTE
AUDIO_R_OUT
I2C_DATA
HS4
HS1 AF_REC
C332
47u
16V
DEM/FILTER
C308
1u
0.66
47
SIF
50V
2.2u
C307
R301
1k
1.5
48
IC301
AN3668FBPEBV
55
JS311
D
R321
3300
C326 C328 C329
33u 10u 10u
25V 16V 16V
2.5
C317
0.1u
C343
0.22u
L301
XX
C345
0.01u
R316
33k
}5%
L302
XX
C304
47u
25V
C320 R310 R311
4.7u
0
0
50V
C318 C319
3.3u 0.1u
50V
0
C301
0.1u
G
L303
100uH
JL328
MPX_MODE
HS3
JL329
C
9
D301
1SS119-25TD
HF_GND
FSC
MA-405 (7/7)
(SEE PAGE 4-19)
SW_12V
JS313
JS312
15
B+
HS7
R320
XX
C331
33u
25V
C325 C327
4.7u 1u
50V 50V
C321 C322 C323 C324
0.1u 10u 4.7u 10u
B
16V 50V 16V
}10%
R313* R314
47k 47k
1/4W 1/10W
R318 R319
47k 47k
I
SIGNAL PATH
AUDIO
SIGNAL
REC
J
PB
AUDIO PROCESS
MA-405(4/7)
4-13
4-14
SLV-LX40/LX50/LX60S/LX70S
MA-405 (TUNER) SCHEMATIC DIAGRAM
– Ref. No: MA-405 board; 1000 series –
• See page 4-5 for printed wiring board.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
MA-405 BOARD(5/7)
TUNER (TU BLOCK)
XX MARK:NO MOUNT
DET OUT
AFT
AUDIO OUT
SIF
IF
IF
B+
R704
560
C701
47u
25V JL717
JL715
JL716
VS15
RF V OUT
8
21 22 23 24
JS753
B+
B+
A5
R703
390
1/4W
NC
10 11 12 13 14 15 16 17 18
B+
C
30V
NC
5V
NC
DATA
CLOCK
6
ENABLE
5
A2
VIDEO IN
4
A3
CONT
3
A4
5V
2
A1
B
CH SW
TU701
AUDIO IN
A
TU VIDEO IN
VT2
TU AUDIO MONO
HT1
MA-405 (2/7)
(SEE PAGE 4-9)
LX40/LX50
RFCH
C705
XX
S701
D
C796
10µ
16V
C709
100u
16V
C797
0.033u
25V
B
C702
0.01u
B
C710
0.01u
B
C712
100u
16V
3CH
+30V
R712
0
2.2uH
L703
RD33ES-T1B3
D702
4CH
2.2uH
L704
+30V
B+
C706
0.01u
B
C704
50V
4.7u
R724
470k
1/10W
JL711
R723
560
1/4W
16
E
MA-405 (7/7)
(SEE PAGE 4-19)
SW_5V
C794
0.22u
B
B+
AN_GND
AN_GND
F
TV/VTR
TS1
PLL CLOCK
TS2
R701
1k
R709
1k
1/4W
JL701
A1
JL702
A2
JL703
A3
JL704
A4
JL705
A5
470p
C798
G
13
PLL DATA
TS3
PLL ENABLE
TS4
R710
1k
R711
1k
MA-405 (3/7)
(SEE PAHE 4-11)
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
C707
2200p
B
470p
C799
470p
C800
TU AFT
H
TS5
SIGNAL PATH
8
JL713
MA-405 (2/7)
(SEE PAHE 4-9)
RF AUDIO OUT
HT3
VIDEO SIGNAL
R702
3300
1/10W
CHROMA
Y
Y/CHROMA
AUDIO
SIGNAL
REC
I
PB
14
MA-405 (4/7)
(SEE PAGE 4-13)
SIF
AN GND
AN_GND
J
TUNER
4-15
4-16
MA-405(5/7)
SLV-LX40/LX50/LX60S/LX70S
MA-405 (DISPLAY CONTROL) SCHEMATIC DIAGRAM
– Ref. No: MA-405 board; 1000 series –
• See page 4-5 for printed wiring board.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
MA-405 BOARD(6/7)
DISPLAY CONTROL (FRONT BLOCK)
A
XX MARK:NO MOUNT
AN_GND
AN_GND
AN_GND
7
HM5
L2(R)
MA-405 (2/7)
(SEE PAGE 4-9)
AU_GND
AU_GND
AU_GND
L2(L)
HM4
L2_VIDEO
L2_V
B
CN401
9P
FJ-32 BOARD
CN801
(SEE PAGE 4-24)
C
JL464
9
L2_VIDEO
AN_GND
8
L2(L)
7
AU_GND
6
L2((R)
5
AU_GND
4
EJECT
3
POWER
2
D_GND
1
R440
12k
JL465
R409
1500
R410
2200
R412
12k
R411
2700
R413
15k
JL467
JL402
JL469
JS401
0.60mm
JL466
ADJ
JL438
JL439
JL440
JL441
S404
S406
JL468
JL427
JL461
JS403
0.60mm
JL463
S412
S408
GND
JL462
R415
1500
D
R416
1500
R417
2200
ESU
CH+
REW
REC
R441
33k
R418
2700
R407
33
JL443
JL444
JL445
S411
S410
S413
STOP
JL447
JL446
S405
S409
PLAY
FF
PAUSE
CH-
JL460
S429
SEARCH
ND420
1
E
F-
S CLK0 MS4
FLD CS MS7
D 5V MS10
4.9
4.9
2.0-3.1
D_GND
C422
47u
16V
L420
22uH
G10
LED1
S18
LED2
S17
LED3
IC404
LED4
VEE
S16
DISPLAY CONTROL
OSC
S15
DOUT
IC404
UPD16315GB-3BS
DIN
S14
S13
CLK
S12
STB
S11
KEY1
S10
KEY2
FS16
FS15
-13.3
FS14
R-8.6/P-6.2
FS16
-6.3
FS15
-4.0-0.6
FS14
-13.1--10.8
FS13
-13.1--10.8
FS12
-13.1--10.8
FS11
-10.8--3.9
FS10
FS13
FS12
FS11
FS10
FS9
FS8
FS7
FS6
JS420
XX
FS5
S9
S8
S7
S6
S5
S4
S3
S2
FS4
S1
VSS
C423
0.01u
B
H
VDD
KKP - MS12
FS3
FS2
12 13 14 15 16 17 18 19 20 21 22
I
KKP -
2
KKP +
1
JL478
D420
RD5.6ES-T1B2
B-
B-
-13V
17
MA-405 (7/7)
(SEE PAGE 4-19)
J
F+
C425
10u
16V
FD_GND
R427
1500
C426
XX
C424
0.1u
F
AN_GND
AN_GND
C427
0.1u
B
DISPLAY CONTROL
MA-405(6/7)
4-17
4-18
4
5
6
8
30 29
-3.9--1.6
FS9
FS8 -10.8--6.5
FS7 -10.8--6.5
FS5
JL477
FS6 -10.8--6.5
-8.5--3.9
-1.7--0.6
-13.1
-10.8
B+
JL410
FS4
3
JL409
FS3
SEARCH
JL408
-6.2--1.7
4
FS2
DI-80 BOARD
CN901
(SEE PAGE 4-25E)
5
FS1
D_GND
TIMER SET
4.9
FS1
CN402
5P
7
FG6
9
G9
G8
G7
G6
G5
FG5
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
-11.1
-11.0
-11.0
-11.0
G4
G3
G2
G1
FG4
23 24 25 26 27 28 29 30 31 32 33
6
1.8
7
S OUT0 MS6
2
5
JS453
0
R425
82k
4
3
R445
1k
R422
1k
R423
1k
R424
1k
KKP + MS11
0
8
MA-405 (3/7)
(SEE PAHE 4-11)
1
SLR-342DCT31
D421
9
C406
100u
10V
FUNC KEY2 MS3
11
VDD
VSS
1
R402
47k
1/4W
FUNC KEY1 MS2
-11.0
4.9
OUT
2
44 43 42 41 40 39 38 37 36 35 34
C405
0.01u
B
REMOCON MS1
G
FG3
11 10
L421
XX
3
R401
100
GND
VCC
F
FG2
JL401
JS402
0.60mm
-11.0
FG1
REMOTE CONTROL
RECEIVER
C421
XX
G1
G2
G3
G4
G5
G6
N.C
N.C
P16
P15
P14
P13
P12
P11
P10
P9
P8
P7
P6
P5
P4
P3
P2
P1
F+
F+
FLUORESCENT TUBE INDICATOR
FG6
FG4
FG5
FG3
B+
FG2
FG1
IC403
F-
2
IC403
SFH5110-40
SLV-LX40/LX50/LX60S/LX70S
MA-405 (POWER SUPPLY) SCHEMATIC DIAGRAM
– Ref. No: MA-405 board; 1000 series –
• See page 4-5 for printed wiring board.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
MA-405 BOARD(7/7)
POWER SUPPLY (PS BLOCK)
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
B
L660
68uH
JL618
13.5
SW_5V
JS606
ET601
C601
0.1u
AC IN
110,120,220V
50/60Hz
R600
XX
C605
120u
200V
C602
470p
250V
R602
150k
1/4W
8
11
7
14
6
VDR601
XX
R605
1500
1/4W
C606
820p
R604
12k
12
4
15
3
16
3
4
5
6
R650
0.60mm
ET600
TERMINAL
GROUND
D623
C608
2200p
800V
PP
MTZJ-T-77-18B
C610
1200p
10V
C615
820u
25V
C624
47u
50V
R641
10 1/4W
JS614
XX
XX
AK04V0
C632
XX
JS630
XX
C627
0.01u
B
C626
47u
50V
JS631
XX
D666
1SS119-25TD
D661
1SS119-25TD
0.60mm
R642
D624
D1NL20U-TA2
R647
68k
R651
39k
R607
8200
1/4W
G
L606
1uH
C636
470u
16V
C630
0.01u
B
R648
2200
PH600
PC123FY2
4
1
R616
R618
47
1/4W 220
1/4W
R615
2200
C612
1u
50V
2
C613
0.12u
PET
R617
1k
1/4W
H
2
3
4.7
GND
3
JS617
MTR_GND2
JL617
C616
470u
25V
JL620
2.4
C629
470u
10V
R669
3300
R613
120
1/4W
P CONT M12
PS2
P CONT SW 12
MA-405 (3/7)
(SEE PAGE 4-11)
D_GND
C665
22u
16V
AN_GND
D_6V
JL613
C662
22u
50V
0.60mm
JS628
OSD_VCC
C664
47u
25V
SW_12V
JS625
XX
C666
47u
16V
0.01u
B
R678
220
1/4W
JS605
C660
47u
16V
JL612
R679
220
1/4W
Q673 10.2
2SC3311A-RTA
+B SWITCH
AU_GND
HF_GND
JS604
0
6.5
R680
1k
1/4W
0.60mm
JL611
JL625
5.8
R643
XX
JL614
-13V
F+
F-
5.9
17
MA-405 (6/7)
(SEE PAGE 4-17)
D_GND
5.1
Q662
2SD2394-EF
5V REG
MA-405 (2/7)
(SEE PAGE 4-9)
JS603
0
R676
1k 1/4W
5.8
AN_GND
AU_GND
PS662
1.6A
C669
5
SW_5V
AN_GND
5.9
R612
2k
±0.5%
10
SW_5V
PS1
SW_12V
C611
470u
16V
JS608
0.60mm
L603
1uH
C631
0.01u
L604 B
1uH
MTR_GND
MTR_12V
4
AN_GND
5.8
5.2
Q674
2SD1664-T100-R
OSD VCC REG
C672
0.1u
F
1
IC601
HA17431PA-TZ
IC601
2
MTR_GND2
MTR_GND
JL615
C607
560p
3
JL604
JS616
0
D660
RD5.1ES-T1B2
RD6.2ES-T1B2
D625
JL619
C628
R606
9100
7
L602
22uH
L601
22uH
D601
D1NL20U-TA2
2
1
D609
31DQ06-FC5
D605
XX
D602
XX
1
JS601
XX
IC POWER MODULE
F
17
JS602
XX
IC600
MA8910
D612
AU02A-V0
D613
R649
47
IC600
D608
D2S4MF
13
5
R640
10
1/4W
C617
XX
10
R603
330k
1/4W
EXCEPT LX50:CL,CS/
LX70S:CL.CS.
C604
470p
250V
D611
AU02A-V0
CONT
CONVERTER
TRANSFORMER
R601
3.3M
1/2W
D607
RD5.6ES-T1B2
CP601
XX
T600
D603
XX
MA-405 (1/7)
(SEE PAGE 4-7)
SW_5V
4.9
VDR600
C603
470p
250V
R668 XX
LF600
R611
1M
1/2W
3
AN_GND
IC660
PQ12RD08
C625
XX
13V
3
12V REG
D600
DF06M-6031
12V
NEUTRAL
JL602
D
D_GND
JS618
0.60mm
IC660
C600
0.1u
250V
FH601
13.5
1
F600
2A
125V
11.7
LIVE
FH600
C621
22u
16V
R619
XX
MA-405 (4/7)
(SEE PAGE 4-13)
SW_5V
R623
3300
0.7
RD16F-T8B1
D614
JL601
HF_GND
R614
1500
±0.5%
2P
D604
XX
CN600
0
15
SW_12V
TERMINAL
GROUND
R622
390
1W
Q601
2SD601A-QRS-TX
PWR CONT SW
EXCEPT LX50:CL,CS/
LX70S:CL.CS.
MA-405 (5/7)
(SEE PAGE 4-15)
AN_GND
12.8
C661
0.01u
B
C
E
Q600
2SB1398-Q(TA).S0
MTR 12V REG
R621
10k
1/4W
C671
22u
50V
16
+30V
13.5
JS609
A
REG
I
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
J
POWER SUPPLY
4-19
4-20
MA-405(7/7)
SLV-LX40/LX50/LX60S/LX70S
MA-405 BOARD (1/7)
(R/P BLOCK)
MA-405 BOARD (2/7)
MA-405 BOARD (3/7)
(VA BLOCK)
(SS BLOCK)
7 IC201 2 REC
1 IC260 4 REC/PB
qf IC201 yj REC/PB
qj IC160 el
4fsc (OUT)
REC/PB
wd IC160 i;T REEL
4.8Vp-p
V
3.6Vp-p
2 IC260 5 REC/PB
H
8 IC201 7 REC
0.1µsec/div
0.1V/div
3.5Vp-p
H
3 IC260 7 PB
0.1µsec/div
50mV/div
360mVp-p
H
0.5Vp-p
5.0Vp-p
OSC OUT
REC/PB
25.3MHz
69.9kHz
4.6Vp-p
ql IC160 t; OSC V IN REC wg IC160 il
DRUM FG
REC/PB
50Vp-p
2.2Vp-p
H
ql IC160 t; OSC V IN PB
4.2Vp-p
H
qa IC201 wl REC
SP
4.4Vp-p
1078Hz
0.6Vp-p
V
wf IC160 ij CAP FG
360Hz
wh IC160 o;
4.5Vp-p
DRUM PG
REC/PB
4.6Vp-p
30Hz
170mVp-p
5 IC260 0 REC
14.31818MHz
qk IC160 rg
qh T380 6 REC
0 IC201 wk REC/PB
4 IC260 9 REC
3.579545MHz R 460mVp-p
qg IC201 1 PB
9 IC201 wd PB
0.6Vp-p
V
380mVp-p
1.6sec (TAPE TOP)
H
w; IC160 ts
2.3Vp-p
OSD V OUT
REC
wj IC160 og CTL+IN
REC
2.2Vp-p
5.0Vp-p
30Hz
H
380mVp-p
6 IC260 qj REC
H
2.1Vp-p
H
AMP OUT
w; IC160 ts OSD V OUT PB wk IC160 oj CTL
PB
qa IC201 wl PB
4.0Vp-p
0.1µsec/div
1V/div
3.8Vp-p
2.3Vp-p
H
qs
RF SW P
IC201 ok REC/PB
2.3Vp-p
H
wa
C VIDEO IN
IC160 th
REC/PB
30Hz
wl IC160 eh
32kHz (OUT)
REC/PB
2.0Vp-p
30Hz
1.6Vp-p
32.768kHz
H
qd IC201 ej REC
H
4-21
3.0Vp-p
ws IC160 ul S REEL
1.0Vp-p
4.8Vp-p
0.9sec (TAPE TOP)
4-22
FJ-32 (LINE 2 IN) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
— Ref. No. FJ-32 Board: 1,000 Series —
There are few cases that the part printed on this
diagram isn’t mounted in this model.
FJ-32 BOARD
1
2
3
4
5
6
7
FJ-32 BOARD
LINE 2 IN
A
•REF.NO.: 1,000 SERIESR801
0
LX40/LX50
CN801 9P
JL801
L2_VIDEO
9
JS801
XX
JL802
8
L2(L)
7
AU_GND
6
L2(R)
5
AU_GND
4
EJECT
3
POWER
2
D GND
1
C803
0.001u
R802
0
JL803
JL804
C805
0.001u
LX60S/LX70S
JL805
C806
0.001u
D803
MA8051-TX
B
MA-405 (6/7)
CN401
(SEE PAGE 4-18)
AN_GND
D801
HZM6.8ZWA1TL
D804
HZM6.8ZWA1TL
D802
HZM6.8ZWA1TL
R803
75
8
7
6
5
4
3
1
2
C
R805
1500
V
R806
33
L
R
CNJ801
JL810
S803
D
S802
JL806
JL807
JL808
POWER
EJECT
E
SIGNAL PATH
F
(POWER, EJECT SWITCH)
(
MA-405
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER, POWER SUPPLY
VIDEO SIGNAL
)
CHROMA
Y
Y/CHROMA
AUDIO
SIGNAL
REC
PB
G
FJ-32 (LINE 2 IN)
H
DI-80 (DIAL TIMER)
LINE 2 IN
4-23
FJ-32
DI-80 (DIAL TIMER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
— Ref. No. DI-80 Board:1,000 Series —
There are few cases that the part printed on this
diagram isn’t mounted in this model.
DI-80 BOARD
1
2
3
4
5
6
7
DI-80 BOARD
DIAL TIMER
A
•REF.NO.: 1,000 SERIES-
B
S901
CN901
5P
D_GND
TIMER SET
MA-405 BOARD(6/7)
CN403
(SEE PAGE 4-17)
SEARCH
C
KKP KKP +
JL901
5
JL902
4
3
2
1
D
(POWER, EJECT SWITCH)
(
MA-405
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER, POWER SUPPLY
)
E
F
FJ-32 (LINE 2 IN)
DI-80 (DIAL TIMER)
G
DIAL TIMER
DI-80
4-24E
4-24
D
JL903
E
JL904
A
JL905
B
COM
DIAL TIMER
(PUSH/TURN)
SLV-LX40/LX50/LX60S/LX70S
SECTION 5
INTERFACE, IC PIN FUNCTION DESCRIPTION
5-1. SYSTEM CONTROL — MECHANISM BLOCK INTERFACE
(MA-405 BOARD IC160)
CASSETTE CASSETTE
TAPE
TAPE
STOP
LOARDING UNLOARDING THREADING UNTEREADING
FF
REW
PB
REC
*5
*5
*5
*5
*5
—
H
H
H
H
H
—
—
L
L
L
H
H
—
—
—
H
H
H
L
L
—
—
—
—
H
L
L
L
L
L
*1
*1
*1
*1
*1
*1
*1
*1
*1
I
H/L
H/L
H/L
H/L
H/L
H/L
*2
*2
*2
*2
MA-405 Board
IC160 ul
I
H/L
H/L
H/L
*2
*2
H/L
*2
*2
*2
*2
END LED
MA-405 Board
IC160 w;
O
L
*3
*3
*3
*3
*3
*3
*3
*3
*3
T SENS
MA-405 Board
IC160 7
I
*3
*3
*3
*4
*4
*4
*4
*4
*4
*4
S SENS
MA-405 Board
IC160 6
I
*3
*3
*3
*4
*4
*4
*4
*4
*4
*4
Signal
Pin No.
I/O
EJECTED
CAM
MA-405 Board
IC160 ed
O
*5
H
L
H
L
MODE 1
MA-405 Board
IC160 wl
I
—
—
—
—
MODE 2
MA-405 Board
IC160 wk
I
—
—
—
MODE 3
MA-405 Board
IC160 wj
I
—
—
MODE 4
MA-405 Board
IC160 wh
I
—
REC PRF
MA-405 Board
IC160 e;
I
T REEL
MA-405 Board
IC160 8
S REEL
*1
*2
*3
*4
*5
“L” When erasing protection tab is bent. “H” when not bent.
Pulse of period in proportion to reel rotating speed.
Approx. 2 msec period “H” pluse when tape top or end is detected.
Normally “L”. 2 msec period “H” puise when tape top or end is detected.
Hi-Z
5-2. SYSTEM CONTROL — SERVO PERIPHERAL CIRCUIT INTERFACE
(MA-405 BOARD IC160)
Signal
CTL IN+
DRUM PG
DRUM FG
CAP FG
CAP RVS
CAP ERR
DRUM ERR
*1.
*2.
*3.
*4.
*5.
*6.
*7.
Pin No.
MA-405 Board
IC160 og
MA-405 Board
IC160 o;
MA-405 Board
IC160 il
MA-405 Board
IC160 ij
MA-405 Board
IC160 ef
MA-405 Board
IC160 uh
MA-405 Board
IC160 uj
TAPE
TAPE
*7
*7
*3
*3
*4
*4
I
H/L
O
I/O
STOP
FF
O
*7
*7
I
*3
I
REW THREADING UNTEREADING
PB
REC
*7
*7
*1
*3
*3
*3
*3
*4
*4
*4
*4
*4
*2
*2
*5
*5
*2
*2
H/L
L
H
L
H
L
L
O
L
*6
*6
*6
*6
*6
*6
O
*6
*6
*6
*6
*6
*6
*6
30Hz pulse.
Pulse of period in propotion to tape speed.
30Hz “H” pluse.
720 Hz pulse.
Unstable period pulse.
DC voltage 1 – 5V.
Hi-Z (2.5V)
5-1
5-3. SYSTEM CONTROL — SYSTEM CONTROL PERIPHERAL CIRCUIT INTERFACE
(MA-405 BOARD IC160)
Signal
RESET
I2C DATA 1
I2C CLOCK 1
I2C DATA VIDEO
I2C CLOCK VIDEO
(ARC) S OUT 1
(ARC) CLK 1
Pin No.
MA-405 Board
IC160 ef
MA-405 Board
IC160 es
MA-405 Board
IC160 ea
MA-405 Board
IC160 us
MA-405 Board
IC160 ua
MA-405 Board
IC160 rs
MA-405 Board
IC160 ra
I/O
I
I/O level
Normally “H”, “L” when service interruption detected or restored.
I/O
Serial communication data to EEPROM I2C161.
O
Serial communication clock to EEPROM I2C161.
I/O
Serial communication data to video and audio microprocessor.
O
Serial communication clock to video and audio microprocessor.
I/O
Serial communication data to ARC microprocessor.
O
Serial communication clock to ARC microprocessor.
5-4. SYSTEM CONTROL AND RF MODULATOR — INPUT SELECTION BLOCK INTERFACE (MA405 BOARD IC160)
Signal
ANT SEL
Pin No.
MA-405 Board
IC160 wa
I/O
O
I/O level
“H” when RF modulator through.
5-5. SYSTEM CONTROL — VIDEO/RP BLOCK INTERFACE (MA-405 BOARD IC160)
Signal
RF SWP
QVD
C SYNC
Pin No.
MA-405 Board
IC160 qk
MA-405 Board
IC160 qd
MA-405 Board
IC160 tk
I/O
STOP/FF
/REW
TAPE
LOADING
TAPE
UNLOADING
PB
REC
REC/
PAUSE
O
*1
*1
*1
*1
*1
*1
O
L
L
L
*2
L
L
I
*3
*3
*3
*3
*3
*3
*1. Synchronized with drum rocation, 30Hz 50% duty pulse.
*2. Normal “L”, “H” when video signal is not rgenerated.
*3. Composite sync signal (positive).
5-6. SYSTEM CONTROL — AUDIO BLOCK INTERFACE (MA-405 BOARD IC160)
Signal
A MUTE
AF REC P
Pin No.
MA-405 Board
IC160 yd
MA-405 Board
IC160 ws
I/O
STOP/FF
/REW
TAPE
LOADING
TAPE
UNLOADING
PB
REC
REC/
PAUSE
O
L
L
L
L
L
L
O
L
L
L
L
H
L
5-2
5-7. SERVO/SYSTEM CONTROL MICROPROCESSOR PIN FUNCTIONS
(MA-405 BOARD IC160)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Pin Name
DEST
MPX MODE
TU AFT
FUNC KEY2
I/O
I
I
I
I
Destination control input
STEREO/MONO/SAP DETECTION
Tuner analog AFT input
Key input
Function
FUNC KEY1
S SENS
T SENS
V RF ENV
AF ANV
CBC ON
KKP+
KKP–
QVD
REMOCON
C ROT
HA SWP
ENV SW
RF SWP
AF SWP
END LED
ANT SEL
AF REC P
FE ON
CAP RVS
SUR ON
MODE4
MODE3
MODE2
MODE1
REC PRF
I2C CLK EEP
I2C DATA EEP
CAM
RESET
32kHz (in)
32kHz (out)
Vcc
4fsc (in)
4fsc (out)
Vss
ARC CLK
ARC DATA
CLK SEL
OSC IN
OSC OUT
NUB
LPF
SP
OSD GND
OSD V IN
I
I
I
I
I
O
I
I
O
I
O
O
I
O
O
O
O
O
—
O
—
I
I
I
I
I
I/O
I/O
O
I
I
O
I
I
O
—
O
O
I
I
O
—
I/O
O
—
I
Key input
Tape end sensor input
Tape top sensor input
Video playback signal envelope input
Hi-Fi audio playback signal envelope input
Cable box control signal output
ETR pulese signal input
ETR pulese signal input
Quasi VD pulese output
Remote sires signal input
Head AZ signal output
SP/EP changed head signal
SP/EP head output lebel ditaction signal
VIDEO RF switching pulse output.
AF switching pulse output.
END sensor LED output
TV/VTR RF modulator control output
Hi-Fi record control pulse output.
NC
Capstan reverse control
NC
Mechanism section CAM encoder input (data4)
Mechanism section CAM encoder input (data3)
Mechanism section CAM encoder input (data2)
Mechanism section CAM encoder input (data1)
Erasing protection tab, cassette IN detection input
HC CLOCK line (EEPROM)
HC DATA line (EEPROM)
Cam motor control signal output
System reset input
Sub clock 32MHz
Sub clock 32MHz
5V
Main clock input
Main clock output
Ground
Realityregenarator (ARC) control clock signal
Realityregenarator (ARC) control data signal
CLOCK seleal “L” Sub clock, “H” main and sub clock.
OSD clock input
OSD clock output
Ground
fsc filter
“L” output when SP mode.
Ground
OSD Video signal input.
5-3
Pin No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Pin Name
WHITE LEVEL
OSD V OUT
OSD Vcc
HLF
V HOLD
C VIDEO IN
NUA
C SYNC
PLL CLK
PLL DATA
PLL ENABLE
TA MUTE
A MUTE
P CONT M12
P CONT SW12
FLD CS
V-SET CS
S OUT0
I/O
I
O
—
I/O
I/O
I
—
I
O
O
O
O
O
O
O
O
O
O
Function
White level signal input
OSD Video signal output
SW 5V (OSD block)
External low-pass filter for slicer/AFC is connected to this terminal
External capacitor for slicer is connected to this terminal
Control video signal input (osd, tuner, sorvo)
D Ground
NC
Tuner PLL clock output
Tuner PLL data output
Tuner enable output
NC
AUDIO mute output
Motor 12V control output
SW 12V control output
FLD drive chip select signal output
V-set micon chip select signal output
Serial communication signal (FLD, V-SET)
S IN 0
S CLK 0
I2C CLK
I2C DATA
CBC SIRCS OUT
CLK OUT
NICOLE
CAP ERR
DRUM ERR
P FAIL
S REEL
T REEL
DMS+
DMS–
MAIN/SAP
F MONO
STEREO
SAP
CAP FG
AMP Vss
DRUM FG
DRUM PG
AMP Vref OUT
AMP Vref IN
RC CHECK
CTL–IN
CTL+IN
AMP C
CTL AMP OUT
AMP Vcc
A Vcc
V-SET RESET
I
O
I/O
I/O
O
—
O
O
O
I
I
I
I
I
O
O
I
I
I
—
I
I
O
I
I
I/O
I/O
I
O
—
—
O
NC
Serial communication signal (FLD, V-SET)
IIC clock signal (VIDEO, HiFi)
IIC data signal (VIDEO, HiFi)
Cable mouse sircs signal output
NC
NC
Capstan error D/A output
Drum error D/A output
Power fail detection input
Supply reel sensor input
Take up reel sensor input
Ground
Ground
Capstan FG signal input
Ground
Drum FG input.
Drum PG input.
Analog AMP reference Vcc output
Analog AMP reference Vcc input
Check input
Control signal IN/OUT
Control signal IN/OUT
Control signal AC conect
Control signal AMP output
D-5V
D-5V
NC
5-4E
5-4
SLV-LX40/LX50/LX60S/LX70S
SECTION 6
ADJUSTMENTS
6-1
MECHANICAL ADJUSTMENTS
For the mechanical adjustments, please refer to the
“VHS MECHANICAL ADJUSTMENT MANUAL
(S MECHANISM)” (9-921-647-11).
6-2. ELECTRICAL ADJUSTMENTS
See the adjusting part location diagram from on page 6-6
for the adjustment.
2-1.
2-1-3. Set-up of Adjustment
In this adjustment, NTSC pattern generator is connected with LINE
input terminal. When check to tuner, connected AERIAL terminal.
Check that the synchronizing signal of the Y signal has an amplitude
of approximately 0.7 V and that the burst signal has an amplitude of
approximately 0.3 V and its waveform is flat. And check that the
level ratio of burst signal to “red” signal is 0.30 : 0.66. The video
signal (color bar) used for electrical aligning this unit is shown in
Fig. 6-2-2.
NTSC model
White (100%)
PREPARATION BEFORE ADJUSTMENT
2-1-1. Equipment Required
The measuring instruments used for this alignment include:
1) Monitor TV
2) Oscilloscope, dual-trace, bandwidth of 30 MHz or more, with
delay mode (A probe 10:1 should be used unless otherwise
specified.)
3) Frequency counter
4) NTSC Pattern generator
5) Remote commander
6) Digital voltmeter
7) Audio generator
8) Audio level meter
9) Audio attenuator
10) Alignment tapes
KRV-51N2 (NTSC) Part No. : 8-192-605-32
About 0.7 V
Red
Horizontal sync signal
VIDEO LINE IN
Pattern generator
Video output
(75Ω)
VCR
Burst signal
(It must be flat.)
Fig. 6-2-2 Color Bar Signals of Pattern Generator
2-1-4. Alignment Tape
• Contents of KRV-51N2
Mode
2-1-2. Equipment Connection
Unless otherwise specified, connect and adjust the measuring
instruments as shown in the following diagram.
About
0.3 V
About
0.3 V
1
2
3
4
Monitor TV
VIDEO LINE OUT
Fig. 6-2-1
6-1
SP
LP
Period
Video signal
Audio signal
Normal
Hi-Fi
7 minutes
3 minutes
7 minutes
3 minutes
Color bar
Monoscope
Color bar
Monoscope
400Hz
(L/R)
400Hz
2-1-5. Input/Output Levels and Impedance
Video input: LINE IN
Input signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
Video output: LINE OUT
Output signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
Audio input: LINE IN
Input level: –7.5 dBs
(0 dBs= 0.775 Vrms)
Input impedance: more than 47 kilohms
Audio output:LINE OUT
Standard level: –7.5 dBs at load impedance 47
kilohms
Output impedance: less than 10 kilohms
2-2.
POWER SUPPLY CHECK
2-2-1. Output Voltage Check (MA-405 Board)
Mode
STANDBY
+30 V Check
Measurement point
2-1-6. Adjustment Sequence
The adjustments should be performed in the following sequence.
Power Supply Check
Servo/Video System Adjustments
Audio System Adjustments
C671 3
Specified value
–11 V Check
31.0 to 39.0 V
Measurement point
Specified value
Anode of D420
–12.5 to – 9.5 V
D+6 V Check
Measurement point
Collector of Q674
Specified value
5.56 to 6.25 V
Mode
Measuring Instrument
E-E
Digital voltmeter
SW+12 V Check
Measurement point
IC660 pin 2
Specified value
SW+5 V Check
11.7 to 12.3 V
Measurement point
Specified value
Emitter of Q662
4.8 to 5.4 V
MTR12 V Check
Measurement point
Collector of Q600
Specified value
F Check
12.5 to 14.5 V
Measurement point
Specified value
ND420 e; to 1
2.0 to 5.0V
[Check Method]
1) Each of these supply voltages must meet its specified value.
6-2
2-3.
SERVO SYSTEM CHECK
2-3-1.
RF Switching Position Adjustment
(MA-405 Board)
[Adjustment Purpose]
To adjust the link of the A-ch and B-ch of the tape playback outputs.
To make the unit compatible with other tapes and units. If this
specification is not satisfied, the link will appear on the screen and
the screen will be disrupted, etc.
2-4.
AUDIO SYSTEM ADJUSTMENT
• Adjust both L ch and R ch.
[Connecting Instruments]
Audio line OUTPUT L/R
Audio line INPUT L/R
Audio oscillator
Mode
600 Ω
Playback
Signal
Measurement point
Alignment tape: SP color bar portion
CH1: CN270 pin 2 (PB RF)
CH2: CN270 pin 3 (RF SWP)
Measuring instrument
Adjusting element
Oscilloscope
Remote Commander CH+/–
Specified value
A=minimize
[Adjustment Method]
1) Playback the alignment tape.
2) Short JS401 to Ground.
3) Check that “A P” is indicated on FL display.
4) Adjust so that part A becomes minimized at CH +/–.
5) Write data in EEPROM by pressing PAUSE button.
Monoral model:
6) The display “A P” disappears and then the Adjustment mode
terminates.
Hi-Fi model:
6) The display changes to “A H” and the mode goes to the HiFi
switching position Adjustment.(2-4-2.)
Audio level meter
or distortion meter
47 kΩ
Attenuator
VTR
Fig. 6-2-4
2-4-1.
Hi-Fi Audio System Adjustment
(Hi-Fi model only)
• Perform the adjustment setting the switch on the following
positions.
• AUDIO MONITOR STEREO
[Adjustment Method]
1. ACE head adjustment.....Refer to the VHS mechanical
adjustment manual (S MECHANISM)(9-921-647-11).
2. E-E output level check
3. “Recording Bias Adjustment”
A
CH1
PB RF
CH2
RF SWP
Fig. 6-2-3
6-3
2-4-2.
HiFi Switching Position Adjustment
(MA-405 Board)
[Adjustment Purpose]
To adjust the link of the A-ch and B-ch of the tape playback outputs.
To make the unit compatible with other tapes and units. If this
specification is not satisfied, the link will appear on the screen and
the screen will be disrupted, etc.
Mode
Playback
Signal
Measurement point
Alignment tape: SP color bar portion
CH1: Pin 1 of CN270 (HF ADJ)
CH2: Pin 3 of CN270 (RF SWP)
Measuring instrument
Adjusting element
Oscilloscope
Remote Commander CH +/–
Specified value
B=minimize
[Adjustment Method]
1) Check that “A H” is indicated on FL display.
2) Adjust so that part B becomes minimized at CH +/–.
3) Write data EEPROM by pressing PAUSE button.
4) Check that “A H” indicator turns off.
5) If “A H” indicator is still on, restart RF switching position
Adjustment from the beginning.
B
CH1
HFADJ
CH2
RF SWP
2-4-5. Audio Noise Check
[Adjustment purpose]
Confirm that the noise level is within the specification.
Mode
REC and PB (SP mode)
Signal
Measurement point
No signal input
Audio output terminal
Measuring instrument
Specified value
Audio level meter
Less than –67,5dBs (HIFI)
Less than –45.5dBs (MONO)
[Confirmation method]
1) Audio line input L and R channels are shorted to the ground.
2) Record the tape.
3) Playback a recorded portion of the tape.
4) Confirm that the output level is less than –67.5dBs for HIFI
and –45.5dBs for MONO.
2-4-6. ACE Head Adjustment
Refer to the VHS mechanical adjustment manual
MECHANISM) (9-921-647-11).
(S
2-4-7. E-E Output Level Check
[Adjustment purpose]
Confirm that the output level adjust the reference input is within the
specification.
Mode
Signal
E-E
400 Hz, –7.5 dBs
Measurement point
Measuring instrument
CNJ562 L/R
Audio level meter
Specified value
–7.5 ± 2 dBs
[Check Method]
1) Input signal of 400 Hz and –7.5 dBs to the CNJ562 L/R.
2) Check that the audio output level is –7.5 ± 2 dBs.
Fig. 6-2-5
2-4-3. Normal Audio System Adjustment
• Make adjustment in the SP mode unless otherwise specified. Use
a normal VHS cassette for an adjustment tape.
• Set AUDIO MONITOR to normal.
2-4-4. Audio Level and Distortion Check
[Adjustment purpose]
Confirm that the audio level and distortion is within the specification.
Mode
Signal
REC and PB (SP mode)
400 Hz, –7.5 dBs
Measurement point
Measuring instrument
Audio output terminal
Audio level meter and distortion
meter
Specified value
PB level
PB level
Distortion
Distortion
2-4-8. Frequency Response Check
[Adjustment purpose]
Confirm that the frequency characteristic is within the specification.
Mode
Signal
REC and PB (SP mode)
400 Hz, –17.5 dBs
7 kHz, –17.5 dBs
Measurement point
Measuring instrument
CNJ562 L/R
Audio level meter
Specified value
0 ± 3 dB
Note: Tape path adjustment must have been completed.
: –7.5±2dBs (HIFI)
: –7.5±3dBs (MONO)
: less than 1% (HIFI)
: less than 4% (MONO)
[Confirmation Method]
1) Supply a signal of 400 Hz, –7.5 dBs to both L and R channels
of Audio Line Input.
2) Record the tape.
3) Playback a recorded portion of the tape.
4) Confirm that the playback output level of audio level meter is
within of range –7.5±2dBs for HIFI and –7.5±3dBs for MONO.
5) Confirm that the output of distortion meter is less than 1% for
HIFI and 4% for MONO.
6-4
[Confirmation Method]
1) Supply a signal of 400 Hz, –17.5 dBs to CNJ562 L/R.
2) Connect the audio level meter to CNJ562 L/R.
3) Adjust the attenuator so that the audio level meter will indicate
–17.5 dBs.
4) Make recording in the SP mode.
5) Set an audio line input signal to 7 kHz and make recording.
6) Playback a recorded portion, and measure output levels at 400
Hz and 7 kHz.
7) Confirm that the 7 kHz playback output level within a range of
the 400 Hz playback output level 0 ± 3 dB.
2-5.
ADJUSTING PARTS LOCATION DIAGRAM
MA-405 BOARD
(CONDUCTOR SIDE)
CNJ562
CN270
4
VIDEO/AUDIO LINE
IN/OUT
1
RF/HF SWP
C671
+
B
E
Q600
MTR12 V
+30 V
+12V
B
4
E
1
Q662
+6V
SW5V
-11V
D420
IC660
ND420
30
6-5E
6-5
JS401
ADJ
1
SLV-LX40/LX50/LX60S/LX70S
SECTION 7
REPAIR PARTS LIST
7-1. EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
7-1-1. FRONT PANEL AND UPPER CASE SECTION
10
11
12
11
8
4
9
7
2
3
13
5
6
1
Ref. No.
Part No.
Description
1
1
1
1
2
X-3951-118-1
X-3951-120-1
X-3951-119-1
X-3951-121-1
3-951-089-01
PANEL ASSY, FRONT (LX40)
PANEL ASSY, FRONT (LX50)
PANEL ASSY, FRONT (LX60S)
PANEL ASSY, FRONT (LX70S)
SPRING (GE), FL (LX40/LX50)
2
3
4
* 5
6
3-951-089-01
3-058-039-11
4-921-277-41
A-6794-813-A
1-757-552-12
SPRING (GE), FL (LX60S/LX70S)
DOOR,CASSETTE
SCREW(B2.6 × 8), TAPPING, BIND
DI-080 MOUNT
CABLE, FLAT FDM-010
* 7
* 7
8
A-6794-814-A FJ-032 MOUNT (LX60S/LX70S)
A-6794-815-A FJ-032 MOUNT (LX40/LX50)
1-757-556-11 CABLE, FLAT FFJ-004
Remarks
Ref. No.
Part No.
!9
1-777-852-12 CORD, POWER (LX40/LX50:MX,PA,PC,VZ/
LX60S/LX70S:MX,PA,PC,VZ)
1-782-000-33 CORD, POWER (LX50:CL,CS/LX70S:CL,CS)
3-053-307-61 CASE, UPPER
3-710-901-01 SCREW, TAPPING
1-476-436-11 COMMANDER, STANDARD (RMT-V293A)
(LX40/LX50)
!9
10
11
12
12
13
7-1
Description
Remarks
1-476-437-11 COMMANDER, STANDARD (RMT-V294A)
(LX60S/LX70S)
3-943-995-51 EMBLEM (NO.5), SONY
7-1-2. CHASSIS SECTION
54
55
#1
#1
#1
54
54
54
54
53
56
52
51
54
not supplied
not supplied
not supplied
Ref. No.
51
52
53
* 53
* 53
Part No.
Description
3-959-383-01 BASE (R), MD
3-987-076-11 PANEL, REAR
A-6713-826-A MA-405 COMPLETE PC BOARD
(LX50:CL,CS)
A-6713-827-A MA-405 COMPLETE PC BOARD
(LX60S/LX70S:MX,PA,PC,VZ)
A-6713-828-A MA-405 COMPLETE PC BOARD
(LX70S:CL,CS)
Remarks
Ref. No.
Part No.
* 53
54
55
56
A-6713-829-A MA-405 COMPLETE PC BOARD
(LX40/LX50:MX,PA,PC,VZ)
3-970-608-21 SUMITITE (B3), +BV
1-791-857-11 CABLE, FLAT (FMD-21)
X-3950-107-1 PANEL ASSY, REAR
#1
7-685-648-79 SCREW + BVTP 3 x 12 TYPE2 IT-3
7-2
Description
Remarks
7-1-3. MECHANISM DECK SECTION-1
707
#2
708
712
711
709
706
723
704
710
705
702
713
720
722
725
703
701
724
701
721
714
716
719
715
717
718
Ref. No.
Part No.
Description
Remarks
701
702
703
704
705
3-977-509-01
3-977-507-01
3-977-508-01
1-500-144-11
3-977-495-01
WASHER, THRUST
TABLE, REEL (S) (GRAY)
TABLE, REEL (T) (BLACK)
HEAD, FE
SHAFT, TG2
706
707
708
709
710
3-977-494-01
A-6759-619-B
3-977-535-01
3-977-536-01
3-977-443-01
HOLDER, FEH
FL COMPLETE ASSY BOARD, COMPLETE
PLATE, LUMINOUS (END SENSOR)
PLATE, LUMINOUS (TOP SENSOR)
WASHER, STOPPER
711
712
713
A-6759-863-B PRESS BLOCK ASSY, PINCH
3-958-455-01 SPRING (PINCH), TENSION
3-977-447-01 GEAR, ELEVATOR
7-3
Ref. No.
Part No.
Description
714
715
716
717
718
3-977-514-01
3-977-441-03
3-977-445-02
3-977-465-01
3-977-446-01
OPENER, LID (SL)
GEAR, PINCH PRESSING
GEAR, TG8 ARM DRIVING
SPRING, EXTENSION (RVS BRAKE)
ARM ASSY, RVS BRAKE (SL)
719
720
721
722
723
3-977-446-01
X-3947-590-1
A-6759-620-A
3-974-556-11
3-979-508-01
GEAR, TG8 ARM
TG8 ASSY
HEAD BLOCK ASSY, ACE
+ HEXA TT 2.6 x 9 (TAPER)
SCREW + HEXA TP SW 3 x 8
724
725
#2
3-059-958-01 SPRING, TG8
3-051-300-03 LOCK ACE SCREW
7-685-646-79 SCREW + BVTP 3 x 8 TYPE2 IT-3
Remarks
7-1-4. MECHANISM DECK SECTION-2
767
770
768
769
761
758
#2
764
762
763
759
760
762
757
763
#3
766
756
765
755
754
752
753
751
Ref. No.
Part No.
Description
751
752
753
754
755
X-3947-581-4
3-977-462-01
X-3947-573-1
X-3947-580-5
3-977-513-02
BRAKE ASSY,MAIN(T)
SPRING,EXTENTION. (MAIN BRAKE)
ARM ASSY, PENDULUM
BRAKE ASSY, MAIN(S)
LEVER, REC PROOF
756
757
758
759
760
3-976-767-01
3-977-487-01
X-3947-587-1
X-3947-589-1
3-977-488-01
SPRING, TENS. (REC. PROOF)
BOSS, TG1 FULCRUM
TG1 ASSY
BAND ASSY, TG1
SPRING (POWER TENSION)
761
A-6750-324-A SHUTTLE (S) BLOCK ASSY
Remarks
Ref. No.
Part No.
Description
762
763
764
765
766
X-3944-378-1
3-965-178-01
3-062-687-01
A-6750-328-G
3-977-501-01
ROLLER ASSY, GUIDE
SPRING
BASE, DRUM
SHUTTLE (T) BLOCK ASSY
PLATE, LUMINOUS
767
768
769
770
770
A-6746-074-G
X-3947-255-1
3-975-724-07
8-839-047-53
8-839-049-53
ROLLER BLOCK ASSY, HC
ROLLER ASSY, HC
ARM, HC
DRUM ASSY, DZH-0A0A/Z-RP
DRUM ASSY, DZH-0A2A/Z-RP
#2
#3
7-685-646-79 SCREW + BCTP 3 x 8 TYPE IT-3
7-682-647-09 SCREW + P3 x 6
7-4
Remarks
(LX60S/LX70S)
(LX40/LX50)
7-1-5. MECHANISM DECK SECTION-3
816
815
817
M902
803
818
803
814
#2
812
813
828
811
829
810
808
809
819
820
827
821
826
807
805
822
804
806
823
824
832
831
830
M903
803
801
825
802
833
#4
Ref. No.
Part No.
Description
801
802
803
804
805
3-977-437-01
X-3947-584-1
3-977-443-01
3-977-438-01
3-977-506-01
RETAINER,CAM MOTOR
ASSY, REEL DIRECT
WASHER, STOPPER
WORM - WHEEL
ARM, LIMITTER SELECTION
806
807
808
809
810
3-977-444-01
3-977-515-01
3-977-517-01
3-977-519-01
3-977-518-02
811
812
813
814
815
3-977-516-01
3-977-877-01
3-977-504-01
X-3947-585-1
3-977-510-01
816
817
818
3-056-824-01 WASHER, STOPPER
3-977-439-01 GEAR, CAM
3-977-442-03 SLIDER
Remarks
Part No.
Description
819
820
821
822
823
3-977-455-01
3-977-456-03
X-3947-579-1
3-977-451-01
3-977-452-01
GEAR, LOADING(T)
SPRING, TORSION (LOAD T)
LEVER ASSY, LOADING(T)
GEAR, LOADING(S)
SPRING, TORSION (LOAD S)
GEAR, PINCH TRANSMISSION
GUIDE, FL SLIDER
PLATE, SLIDE, FL
SPRING, TENS. (LIMIT, FL)
PLATE, LIMITTER, FL
824
825
826
827
828
X-3947-578-1
X-3947-576-2
3-977-468-01
3-977-467-02
X-3947-583-1
LEVER ASSY, LOADING (S)
CHASSIS ASSY, MECHANICAL
SHAFT, CAPSTAN BRAKE
SPRING, CAP BRAKE
BRAKE ASSY, CAPSTAN
HOLDER, FL SLIDER
PLATE, RETAINER
GEAR, CLUTCH
GEAR ASSY, PULLEY
BELT, RUBBER
829
830
831
832
833
3-977-489-01
A-6759-616-A
1-766-723-21
3-977-436-01
3-989-917-01
ARM, TG1 DRIVING
GEAR BLOCK ASSY, LOADING (S)
CONNECTOR, BOARD TO BOAR 3P
WORM
SPACER (REC PROOF)
M902
M903
1-698-971-11 MOTOR, DC (CAPSTAN)
X-3947-577-1 MOTOR ASSY, CAM (LOADING)
#2
#4
7-685-646-79 SCREW + BVTP 3 x 8 TYPE IT-3
7-685-133-19 SCREW + P2.6 x 6 TYPE2 NON-SLIT
7-5E
7-5
Ref. No.
Remarks
MA-405
Ref.
No.
7-2.
Part No.
Description
ELECTRICAL
PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they may
have some difference from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
• CAPACITORS:
uF: µF
Ref. No.
Part No.
•
•
•
Remarks
Ref. No.
Part No.
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
COILS
uH: µH
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
Description
Remarks
Ref. No.
Part No.
Description
DI-80
Remarks
When indicating parts by reference number,
please include the board name.
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
Description
Remarks
<RESISTOR>
A-6794-813-A D1-080 BOARD MOUNT
*******************
CN901
FJ-32
R801
R802
R803
R805
R806
1-770-514-31 CONNECTOR, FFC/FPC 5P
1-216-295-00
1-216-295-00
1-216-022-00
1-216-053-00
1-216-013-00
SHORT
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
0
0 (LX60S/LX70S)
75
5%
1/10W
1.5K
5%
1/10W
33
5%
1/10W
<SWITCH>
S901
<SWITCH>
1-418-156-11 ENCODER, ROTARY
S802
S803
1-762-196-21 SWITCH, TACT
1-762-196-21 SWITCH, TACT
A-6794-814-A FJ-032 BOARD MOUNT (LX60S/LX70S)
A-6794-815-A FJ-032 BOARD MOUNT (LX40/LX50)
******************
A-6713-829-A MA-405 N3 BOARD COMPLETE
(LX40/LX50:PA,PC,MX,VZ)
A-6712-826-A MA-405 N3A BOARD COMPLETE (LX50:CL,CS)
A-6713-827-A MA-405 N5 BOARD COMPLETE
(LX-60S/LX70S:PA,PC,MX,VZ)
A-6713-828-A MA-405 N5A BOARD COMPLETE
(LX70S:CL,CS)
**************************
<CAPACITOR>
C803
C805
C806
1-163-009-11 CERAMIC CHIP
0.001µF 10%
1-163-009-11 CERAMIC CHIP
0.001µF 10%
(LX60S/LX70S ONLY)
1-163-009-11 CERAMIC CHIP
0.001µF 10%
50V
50V
50V
<CONNECTOR>
CN801
3-065-135-01 HOLDER, FL
3-960-273-11 SPACER, TOP END
3-065-718-11 SINK, HEAT (LX50:CL,CS)
1-568-852-11 CONNECTOR, FFC/FPC 9P
<JACK>
C101
C102
C103
C104
C105
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-128-057-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001µF
0.001µF
0.001µF
0.001µF
330µF
10%
10%
10%
10%
20%
50V
50V
50V
50V
6.3V
C106
C107
C108
C109
C111
1-124-589-11
1-164-346-11
1-164-004-11
1-164-004-11
1-164-232-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47µF
1µF
0.1µF
0.1µF
0.01µF
20%
DIODE HZM6.8ZWA1TL
DIODE HZM6.8ZWA1TL
DIODE MA8051-TX
DIODE HZM6.8ZWA1TL
10%
10%
10%
16V
16V
25V
25V
50V
<CHIP CONDUCTOR>
C112
C113
0.01µF
0.1µF
10%
10%
50V
25V
C115
C116
C140
1-164-232-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
(LX60S/LX70S)
1-164-232-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
1-124-584-00 ELECT
0.01µF
0.01µF
100µF
10%
10%
20%
50V
50V
10V
C141
C142
1-163-038-00 CERAMIC CHIP
1-163-037-11 CERAMIC CHIP
0.1µF
0.022µF 10%
25V
50V
CNJ801 1-785-622-11 JACK, PIN 2P (LX40/LX50)
CNJ801 1-770-021-11 JACK, PIN 3P (LX60S/LX70S)
<DIODE>
D801
D802
D803
D804
JR801
8-719-071-15
8-719-071-15
8-719-422-37
8-719-071-15
1-216-296-00 SHORT
0
<JUMPER SELECTOR>
JS801
1-216-295-00 SHORT
0 (LX40/LX50)
7-6
MA-405
Ref. No.
Part No.
Description
Remarks
C143
C144
C145
1-126-965-11 ELECT
1-126-965-11 ELECT
1-126-935-11 ELECT
22µF
22µF
470µF
20%
20%
20%
50V
50V
10V
C146
C160
C161
C162
C163
1-164-161-11
1-163-809-11
1-163-809-11
1-163-038-00
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022µF
0.047µF
0.047µF
0.1µF
0.047µF
10%
10%
10%
10%
50V
25V
25V
25V
25V
C164
C165
C166
C167
C168
1-163-102-00
1-163-102-00
1-163-231-11
1-163-233-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
24PF
24PF
15PF
18PF
100µF
5%
5%
5%
5%
20%
50V
50V
50V
50V
10V
C169
C170
C171
C172
C173
1-163-038-00
1-163-137-00
1-127-737-11
1-164-232-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
DOUBLE LAYER
CERAMIC CHIP
CERAMIC CHIP
0.1µF
680PF
0.33F
0.01µF
0.01µF
C176
C185
C187
C188
C190
1-164-004-11
1-109-982-11
1-164-346-11
1-109-982-11
1-124-589-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1µF
1µF
1µF
1µF
47µF
C201
C202
C203
5%
10%
10%
10%
10%
25V
50V
5.5V
50V
50V
Ref. No.
Part No.
Description
Remarks
C237
C238
1-164-232-11 CERAMIC CHIP
1-124-589-11 ELECT
0.01µF
47µF
10%
20%
50V
16V
C239
C240
C241
C242
C243
1-164-232-11
1-124-589-11
1-164-232-11
1-164-232-11
1-162-306-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
0.01µF
47µF
0.01µF
0.01µF
0.01µF
10%
20%
10%
10%
20%
50V
16V
50V
50V
16V
C244
C245
C246
C247
C248
1-109-982-11
1-109-982-11
1-162-306-11
1-163-037-11
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
CERAMIC CHIP
1µF
1µF
0.01µF
0.022µF
0.047µF
10%
10%
20%
10%
10%
10V
10V
16V
50V
25V
C249
C250
C251
C252
C253
1-109-982-11
1-163-809-11
1-164-004-11
1-162-306-11
1-163-241-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
1µF
0.047µF
0.1µF
0.01µF
39PF
10%
10%
10%
20%
5%
10V
25V
25V
16V
50V
C254
1µF
10%
10V
0.1µF
10%
25V
C267
C271
C272
1-109-982-11 CERAMIC CHIP
(LX60S/LX70S)
1-164-004-11 CERAMIC CHIP
(LX60S/LX70S)
1-164-004-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
0.1µF
0.01µF
0.1µF
10%
10%
10%
25V
50V
25V
1-164-232-11
1-164-004-11
1-163-037-11
1-164-004-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01µF
0.1µF
0.022µF
0.1µF
100µF
10%
10%
10%
10%
20%
50V
25V
50V
25V
10V
10%
20%
25V
10V
16V
10V
16V
0.047µF 10%
0.01µF 10%
0.001µF 5%
25V
50V
50V
C204
C205
1-163-809-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
1-163-275-11 CERAMIC CHIP
(LX40/LX50)
1-109-982-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
1µF
0.01µF
10%
10%
10V
50V
C275
C276
C278
C279
C280
C206
C207
C208
C209
C210
1-164-004-11
1-163-241-11
1-164-232-11
1-124-589-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1µF
39PF
0.01µF
47µF
0.1µF
10%
5%
10%
20%
10%
25V
50V
50V
16V
25V
C281
C282
C283
C284
C285
1-164-232-11
1-164-232-11
1-164-232-11
1-164-489-11
1-162-306-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
0.01µF
0.01µF
0.01µF
0.22µF
0.01µF
10%
10%
10%
10%
20%
50V
50V
50V
16V
16V
C211
C213
C214
C215
C216
1-163-239-11
1-163-131-00
1-163-257-11
1-163-227-11
1-126-160-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
33PF
390PF
180PF
10PF
1µF
5%
5%
5%
0.50PF
20%
50V
50V
50V
50V
50V
C286
C301
C302
C303
C304
1-163-251-11
1-164-004-11
1-164-232-11
1-164-004-11
1-104-664-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
0.1µF
0.01µF
0.1µF
47µF
5%
10%
10%
10%
20%
50V
25V
50V
25V
25V
C217
C220
C221
C222
C223
1-163-037-11
1-164-232-11
1-109-982-11
1-126-157-11
1-124-234-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.022µF
0.01µF
1µF
10µF
22µF
10%
10%
10%
20%
20%
50V
50V
10V
16V
16V
C305
C306
C307
C308
C309
1-104-664-11
1-163-037-11
1-124-257-00
1-164-346-11
1-164-004-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
47µF
0.022µF
2.2µF
1µF
0.1µF
20%
10%
20%
10%
25V
50V
50V
16V
25V
C224
C225
C226
C227
C228
1-164-004-11
1-126-160-11
1-164-004-11
1-164-004-11
1-124-589-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1µF
1µF
0.1µF
0.1µF
47µF
10%
20%
10%
10%
20%
25V
50V
25V
25V
16V
C310
C311
C312
C313
C314
1-126-964-11
1-124-257-00
1-126-964-11
1-126-964-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
10µF
2.2µF
10µF
10µF
10µF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C229
C230
C231
C232
C233
1-164-004-11
1-163-038-00
1-124-589-11
1-109-982-11
1-126-157-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.1µF
0.1µF
47µF
1µF
10µF
10%
20%
10%
20%
25V
25V
16V
10V
16V
C315
C316
C317
C318
C319
1-126-964-11
1-109-979-81
1-164-004-11
1-126-162-11
1-164-004-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
10µF
3.3µF
0.1µF
3.3µF
0.1µF
20%
10%
10%
20%
10%
50V
50V
25V
50V
25V
C234
C235
C236
1-109-982-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
1µF
0.1µF
0.01µF
10%
10%
10%
10V
25V
50V
C320
C321
C322
1-126-163-11 ELECT
1-164-004-11 CERAMIC CHIP
1-126-157-11 ELECT
4.7µF
0.1µF
10µF
20%
10%
20%
50V
25V
16V
7-7
C255
MA-405
Ref. No.
Part No.
Description
Remarks
C323
C324
1-126-163-11 ELECT
1-109-978-81 ELECT
4.7µF
10µF
20%
10%
50V
16V
C325
C326
C327
C328
C329
1-126-163-11
1-124-242-00
1-126-160-11
1-126-157-11
1-126-157-11
ELECT
ELECT
ELECT
ELECT
ELECT
4.7µF
33µF
1µF
10µF
10µF
20%
20%
20%
20%
20%
50V
25V
50V
16V
16V
C330
C331
C332
C333
C334
1-163-023-00
1-124-242-00
1-124-589-11
1-164-004-11
1-164-489-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.015µF
33µF
47µF
0.1µF
0.22µF
10%
20%
20%
10%
10%
50V
25V
16V
25V
16V
C336
C337
C338
C339
C340
1-164-004-11
1-164-232-11
1-164-232-11
1-164-004-11
1-163-023-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1µF
0.01µF
0.01µF
0.1µF
0.015µF
10%
10%
10%
10%
10%
25V
50V
50V
25V
50V
C341
C342
C343
C345
C350
1-126-157-11
1-126-157-11
1-164-489-11
1-164-232-11
1-126-160-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
10µF
10µF
0.22µF
0.01µF
1µF
20%
20%
10%
10%
20%
16V
16V
16V
50V
50V
C351
C352
C353
1-104-664-11 ELECT
1-163-038-00 CERAMIC CHIP
1-126-160-11 ELECT
(LX40/LX50)
1-126-157-11 ELECT
1-126-160-11 ELECT
(LX40/LX50)
47µF
0.1µF
1µF
20%
20%
25V
25V
50V
10µF
1µF
20%
20%
16V
50V
C356
C357
C358
C359
C360
1-124-242-00
1-126-163-11
1-126-160-11
1-163-009-11
1-163-014-00
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
33µF
4.7µF
1µF
0.001µF
0.0027µF
20%
20%
20%
10%
10%
25V
50V
50V
50V
50V
C362
C363
C364
C365
C366
1-124-589-11
1-126-163-11
1-126-157-11
1-164-232-11
1-126-160-11
ELECT
ELECT
ELECT
CERAMIC CHIP
ELECT
47µF
4.7µF
10µF
0.01µF
1µF
20%
20%
20%
10%
20%
16V
50V
16V
50V
50V
C368
C369
0.01µF
4.7µF
10%
20%
50V
50V
C371
C380
C381
1-164-232-11 CERAMIC CHIP
1-126-163-11 ELECT
(LX40/LX50)
1-163-135-00 CERAMIC CHIP
1-137-374-11 MYLAR
1-164-232-11 CERAMIC CHIP
560PF
5%
0.047µF 5%
0.01µF 10%
50V
50V
50V
C382
C383
C405
C406
C422
1-164-232-11
1-124-589-11
1-164-232-11
1-124-584-00
1-124-589-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.01µF
47µF
0.01µF
100µF
47µF
10%
20%
10%
20%
20%
50V
16V
50V
10V
16V
C423
C424
C425
C427
C500
1-164-232-11
1-163-038-00
1-126-157-11
1-164-004-11
1-163-231-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01µF
0.1µF
10µF
0.1µF
15PF
10%
20%
10%
5%
50V
25V
16V
25V
50V
C501
C502
1-163-231-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
15PF
0.01µF
5%
10%
50V
50V
C354
C355
Ref. No.
Part No.
Description
Remarks
C503
C504
C505
1-163-017-00 CERAMIC CHIP
1-163-275-11 CERAMIC CHIP
1-162-199-31 CERAMIC
0.0047µF 10%
0.001µF 5%
10PF
5%
50V
50V
50V
C507
C508
C509
C510
C511
1-163-137-00
1-109-982-11
1-163-016-00
1-164-004-11
1-163-038-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
680PF
1µF
0.0039µF
0.1µF
0.1µF
5%
10%
10%
10%
50V
10V
50V
25V
25V
C512
C513
C514
C561
C562
1-124-584-00
1-163-009-11
1-163-009-11
1-164-232-11
1-104-664-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100µF
0.001µF
0.001µF
0.01µF
47µF
20%
10%
10%
10%
20%
10V
50V
50V
50V
25V
C563
C564
C570
C571
C572
1-126-935-11
1-164-004-11
1-164-232-11
1-109-982-11
1-126-163-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
470µF
0.1µF
0.01µF
1µF
4.7µF
20%
10%
10%
10%
20%
10V
25V
50V
10V
50V
C573
C574
C575
C576
C577
1-110-501-11
1-126-157-11
1-164-232-11
1-124-584-00
1-164-232-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.33µF
10µF
0.01µF
100µF
0.01µF
10%
20%
10%
20%
10%
16V
16V
50V
10V
50V
C578
! C600
! C601
! C602
! C603
1-164-232-11
1-104-705-11
1-104-705-11
1-113-900-11
1-113-900-11
CERAMIC CHIP
MYLAR
MYLAR
CERAMIC
CERAMIC
0.01µF
0.1µF
0.1µF
470PF
470PF
10%
20%
20%
10%
10%
50V
250V
250V
250V
250V
! C604
! C605
1-113-900-11 CERAMIC
470PF
1-127-932-41 ELECT
150µF
(LX50:CL,CS/LX70S:CL,CS)
1-119-882-51 ELECT(BLOCK)
120µF
(LX40/LX50:MX,PA,PC,VZ/
LX60S/LX70S:MX,PA,PC,VZ)
1-130-470-00 MYLAR
820PF
1-107-737-11 MYLAR
560PF
10%
20%
250V
400V
20%
200V
5%
5%
50V
50V
! C608
C610
C611
C612
C613
1-131-974-11
1-137-921-11
1-126-935-11
1-126-160-11
1-130-496-00
FILM
ELECT
ELECT
ELECT
MYLAR
2200PF
1500µF
470µF
1µF
0.12µF
5%
20%
20%
20%
5%
800V
10V
16V
50V
50V
C615
C616
C621
C624
C626
1-131-976-21
1-126-941-11
1-124-234-00
1-126-967-11
1-126-967-11
ELECT
ELECT
ELECT
ELECT
ELECT
820µF
470µF
22µF
47µF
47µF
20%
20%
20%
20%
20%
25V
25V
16V
50V
50V
C627
C629
C630
C631
C636
1-164-232-11
1-135-372-31
1-164-232-11
1-164-232-11
1-126-935-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01µF
470µF
0.01µF
0.01µF
470µF
10%
20%
10%
10%
20%
50V
10V
50V
50V
16V
C660
C661
C662
C664
C665
1-124-589-11
1-164-232-11
1-126-965-11
1-104-664-11
1-124-234-00
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
47µF
0.01µF
22µF
47µF
22µF
20%
10%
20%
20%
20%
16V
50V
50V
25V
16V
!C605
C606
C607
7-8
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
MA-405
Ref. No.
Part No.
Description
C666
C669
C671
C672
C701
1-124-589-11
1-164-232-11
1-126-965-11
1-164-159-21
1-104-664-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC
ELECT
47µF
0.01µF
22µF
0.1µF
47µF
20%
10%
20%
20%
16V
50V
50V
50V
25V
Remarks
C702
C704
C706
C707
C709
1-164-232-11
1-126-163-11
1-164-232-11
1-164-161-11
1-126-933-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01µF
4.7µF
0.01µF
0.0022µF
100µF
10%
20%
10%
10%
20%
50V
50V
50V
50V
16V
C710
C712
C794
C798
C799
1-164-232-11
1-126-933-11
1-164-489-11
1-163-133-00
1-163-133-00
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01µF
100µF
0.22µF
470PF
470PF
10%
20%
10%
5%
5%
50V
16V
16V
50V
50V
C800
1-163-133-00 CERAMIC CHIP
470PF
5%
50V
Ref. No.
Part No.
Description
Remarks
D607
D608
8-719-109-89 DIODE RD5.6ES-T1B2
8-719-022-97 DIODE D2S4MF
D609
D611
D612
D613
D614
8-719-083-43
8-719-313-17
8-719-313-17
8-719-043-76
8-719-160-64
DIODE 31DQ06-FA7
DIODE AU02A-V0
DIODE AU02A-V0
DIODE AK04V0
DIODE RD16F-T8B1
D623
D624
D625
D660
D661
8-719-109-93
8-719-063-70
8-719-110-49
8-719-109-85
8-719-911-19
DIODE RD6.2ES-T1B2
DIODE D1NL20U-TA2
DIODE MTZJ-T-77-18B
DIODE RD5.1ES-T1B2
DIODE 1SS119-25TD
D666
D702
8-719-911-19 DIODE 1SS119-25TD
8-719-150-92 DIODE RD33ES-T1B3
<TERMINAL>
<CONNECTOR>
ET600
ET601
CN101 1-766-978-31
CN101 1-784-484-11
CN102 1-779-723-11
CN103 * 1-766-716-11
CN104 1-506-469-11
CONNECTOR, FFC/FPC 5P
CONNECTOR, FFC/FPC 5P
CONNECTOR, BOARD TO BOARD 9P
CONNECTOR, BOARD TO BOARD 3P
PIN, CONNECTOR 4P
CN260 1-766-984-41
CN260 1-784-490-11
CN260 1-691-038-31
CN260 1-784-485-11
CN270 * 1-560-892-00
CONNECTOR, FFC/FPC 11P (LX60S/LX70S)
CONNECTOR, FFC/FPC 11P (LX60S/LX70S)
HOUSING, CONNECTOR 6P (LX40/LX50)
CONNECTOR, FFC/FPC 6P (LX40/LX50)
PIN, CONNECTOR 4P
CN350
CN350
CN351
CN401
CN402
CONNECTOR, FFC/FPC 7P
CONNECTOR, FFC/FPC 7P
PIN, CONNECTOR 3P
CONNECTOR, FFC/FPC 9P
CONNECTOR, FFC/FPC 5P
1-766-980-71
1-784-486-11
1-506-468-11
1-784-488-11
1-766-978-31
1-537-771-21 TERMINAL BOARD, GROUND
1-537-771-21 TERMINAL BOARD, GROUND
<FUSE>
! F600
! F600
1-532-203-00 FUSE 50CS-CL (LX50:CL,CS/LX70S:CL,CS)
1-532-743-11 FUSE, GLASS CYLINDRICAL(DIA.5)
(LX40/LX50:MX,PA,PC,VZ/
LX60S/LX70S:MX,PA,PC,VZ)
<FUSE HOLDER>
FH600
FH601
1-533-217-31 HOLDER, FUSE
1-533-217-31 HOLDER, FUSE
<IC>
CN402 1-784-484-11 CONNECTOR, FFC/FPC 5P
! CN600 * 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
IC101
IC160
IC161
IC162
IC201
8-759-645-07
6-800-024-01
8-759-672-79
8-759-248-87
8-759-826-70
IC LB1943N
IC M37760M8H119GP
IC M24C02-WMN6T(A)
IC MM1256XF-BE
IC LA71053M-MPB
IC260
IC301
IC301
IC350
IC403
8-759-564-36
8-759-696-38
8-759-696-39
8-759-499-30
8-749-015-48
IC LA70011
IC AN3668FBPEBV
IC AN3668FBP-V
IC BA7755AF-E2
IC RPM6940
IC404
IC570
! IC600
! IC601
IC660
8-759-643-83
8-759-566-07
8-749-018-38
8-759-420-19
8-759-438-18
IC UPD16315GB-3BS
IC LA7277M-TLM
IC MA8910
IC AN1431T-TA
IC PQ12RD08
<JACK>
CNJ562 1-793-001-21 JACK, PIN (6P) (LX60S/LX70S)
CNJ562 1-779-010-11 JACK, PIN 4P (LX40/LX50)
<DIODE>
D103
D109
D161
D162
D301
8-719-048-26
8-719-200-82
8-719-200-82
8-719-200-82
8-719-911-19
DIODE GL528V1
DIODE MPG06D-6052PKG3
DIODE MPG06D-6052PKG3
DIODE MPG06D-6052PKG3
DIODE 1SS119-25TD
D302
D351
D352
D420
D421
8-719-911-19
8-719-911-19
8-719-911-19
8-719-109-89
8-719-056-06
DIODE 1SS119-25TD
DIODE 1SS119-25TD (LX40/LX50)
DIODE 1SS119-25TD (LX40/LX50)
DIODE RD5.6ES-T1B2
DIODE SLR-342DCT31
D561
D600
D601
8-719-110-08 DIODE RD8.2ES-T1B
8-719-051-93 DIODE DF06M-6031
8-719-063-70 DIODE D1NL20U-TA2
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
<CHIP CONDUCTOR>
JR001
JR002
JR003
JR004
JR006
7-9
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
MA-405
Ref. No.
Part No.
Description
JR007
JR008
JR009
JR010
JR011
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
Remarks
Ref. No.
JR012
JR013
JR014
JR015
JR016
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR017
JR018
JR101
JR102
JR103
1-216-295-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L101
L161
L162
L163
L201
1-414-179-51
1-414-185-51
1-414-185-51
1-414-185-51
1-414-946-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
2.2µH
22µH
22µH
22µH
39µH
JR104
JR105
JR106
JR107
JR108
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L202
L203
L204
L205
L206
1-414-857-51
1-414-856-51
1-414-857-51
1-414-857-51
1-414-857-51
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100µH
10µH
100µH
100µH
100µH
JR109
JR110
JR111
JR112
JR113
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L207
L270
L303
L380
L420
1-414-193-51
1-414-857-51
1-414-857-51
1-414-857-51
1-414-185-51
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
220µH
100µH
100µH
100µH
22µH
JR114
JR115
JR116
JR117
JR118
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L500
L501
L561
L570
L601
1-414-930-21
1-414-857-51
1-414-857-51
1-414-857-51
1-403-588-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
2.2µH
100µH
100µH
100µH
22µH
JR119
JR120
JR121
JR122
JR123
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L602
L603
L604
L606
L660
1-403-588-11
1-414-142-11
1-414-142-11
1-414-142-11
1-410-519-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
22µH
1µH
1µH
1µH
68µH
JR124
JR125
JR126
JR127
JR128
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L703
L704
1-414-179-51 INDUCTOR
1-414-179-51 INDUCTOR
2.2µH
2.2µH
JR129
JR130
JR131
JR132
JR133
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR134
JR135
JR136
JR137
JR138
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR139
1-216-296-00 SHORT
0
0
0 (LX40/LX50)
Remarks
0 (LX40/LX50)
0 (LX40/LX50)
0
JS521
JS603
JS604
JS616
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
0 (LX40/LX50)
0
0
0
SHORT
SHORT
SHORT
SHORT
<COIL>
<FILTER>
! LF600
1-416-929-11 FILTER, LINE
<FLUORESCENT INDICATOR TUBE>
1-517-925-11 TUBE, FLUORESCENT INDICATOR
<PHOTO COUPLER>
! PH101
! PH102
! PH600
<JUMPER SELECTOR>
1-216-295-00 SHORT
1-216-295-00 SHORT
Description
1-216-296-00 SHORT
1-216-295-00 SHORT
1-216-295-00 SHORT
ND420
JS304
JS323
Part No.
JS324
JS325
JS453
8-749-015-86 PHOTO INTERRUPTER GP3S120S
8-749-015-86 PHOTO INTERRUPTER GP3S120S
8-749-010-64 PHOTO COUPLER PC123FY2
<IC LINK>
! PS101
! PS662
7-10
1-532-727-11 LINK, IC 0.25A/150V
1-533-710-11 FUSE (SMD)
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
MA-405
Ref. No.
Part No.
Description
Remarks
<TRANSISTOR>
TRANSISTOR PT380F3
TRANSISTOR PT380F3
TRANSISTOR 2SC1815GR-TPE2
TRANSISTOR 2SC2712Y-TE85L
TRANSISTOR 2SC2712Y-TE85L
Ref. No.
Part No.
Description
Remarks
R166
R167
1-216-073-00 RES-CHIP
1-249-431-11 CARBON
10K
15K
5%
5%
1/10W
1/4W
R168
R169
R170
R171
R172
1-216-073-00
1-216-073-00
1-247-843-11
1-216-089-00
1-216-073-00
RES-CHIP
RES-CHIP
CARBON
RES-CHIP
RES-CHIP
10K
10K
3.3K
47K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/10W
Q101
Q102
Q103
Q201
Q202
8-729-043-84
8-729-043-84
8-729-281-53
8-729-230-49
8-729-230-49
Q203
Q204
Q301
Q302
Q303
8-729-216-21 TRANSISTOR 2SA1162Y-TE85L
8-729-422-27 TRANSISTOR 2SD601A-QRS-TX
(LX60S/LX70S)
8-729-216-21 TRANSISTOR 2SA1162Y-TE85L
8-729-230-49 TRANSISTOR 2SC2712Y-TE85L
8-729-230-49 TRANSISTOR 2SC2712Y-TE85L
R174
R175
R176
R177
R178
1-216-039-00
1-249-413-11
1-249-413-11
1-249-413-11
1-216-105-91
RES-CHIP
CARBON
CARBON
CARBON
RES-CHIP
390
470
470
470
220K
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
1/4W
1/10W
Q350
Q351
Q380
Q500
Q502
8-729-281-53
8-729-230-49
8-729-821-15
8-729-216-22
8-729-216-21
TRANSISTOR 2SC1815GR-TPE2
TRANSISTOR 2SC2712Y-TE85L (LX40/LX50)
TRANSISTOR 2SD1620-TD
TRANSISTOR 2SB709A-QRS-TX
TRANSISTOR 2SA1162Y-TE85L
R179
R180
R183
R185
R187
1-216-113-00
1-216-061-00
1-216-295-00
1-216-295-00
1-216-295-00
RES-CHIP
RES-CHIP
SHORT
SHORT
SHORT
470K
3.3K
0
0
0
5%
5%
1/10W
1/10W
Q561
Q600
Q601
Q662
Q673
8-729-216-22
8-729-047-92
8-729-422-27
8-729-019-01
8-729-119-78
TRANSISTOR 2SB709A-QRS-TX
TRANSISTOR 2SB1398-Q(TA).S0
TRANSISTOR 2SD601A-QRS-TX
TRANSISTOR 2SD2394-EF
TRANSISTOR 2SC3311A-RTA
R188
R189
R191
R192
R193
1-216-069-00
1-216-061-00
1-249-417-11
1-249-417-11
1-216-295-00
RES-CHIP
RES-CHIP
CARBON
CARBON
SHORT
6.8K
3.3K
1K
1K
0
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
Q674
8-729-106-68 TRANSISTOR 2SD1664-T100-R
R194
R201
R202
R203
R204
1-216-073-00
1-216-037-00
1-216-047-91
1-216-037-00
1-216-071-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
330
820
330
8.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R205
R208
R209
R210
R211
1-208-830-11
1-216-295-00
1-216-067-00
1-216-053-00
1-216-065-00
METAL CHIP
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
100K
0
5.6K
1.5K
4.7K
0.5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R212
R213
R214
R215
R216
1-216-043-91
1-216-049-00
1-216-053-00
1-216-071-00
1-249-420-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
CARBON
560
1K
1.5K
8.2K
1.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W
R219
R220
R221
R223
R224
1-247-807-31
1-216-295-00
1-216-295-00
1-216-045-00
1-216-089-00
CARBON
SHORT
SHORT
RES-CHIP
RES-CHIP
100
0
0
680
47K
5%
1/4W
5%
5%
1/10W
1/10W
R225
680
5%
1/10W
R231
R267
R270
R271
1-216-045-00 RES-CHIP
(LX60S/LX70S)
1-216-089-00 RES-CHIP
1-216-295-00 SHORT
1-216-041-00 RES-CHIP
1-216-041-00 RES-CHIP
47K
0
470
470
5%
1/10W
5%
5%
1/10W
1/10W
R272
R274
R276
R277
R278
1-208-788-11
1-216-061-00
1-216-069-00
1-216-081-00
1-216-081-00
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.8K
3.3K
6.8K
22K
22K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R279
R301
R302
R303
R305
1-216-081-00
1-249-417-11
1-216-049-00
1-216-049-00
1-216-033-00
RES-CHIP
CARBON
RES-CHIP
RES-CHIP
RES-CHIP
22K
1K
1K
1K
220
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
<RESISTOR>
R101
R102
R103
R104
R105
1-249-413-11
1-216-077-91
1-216-077-91
1-249-433-11
1-249-433-11
CARBON
RES-CHIP
RES-CHIP
CARBON
CARBON
470
15K
15K
22K
22K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/4W
1/4W
R106
R107
R109
R110
R111
1-249-400-11
1-249-400-11
1-249-437-11
1-216-089-00
1-216-057-00
CARBON
CARBON
CARBON
RES-CHIP
RES-CHIP
39
39
47K
47K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/10W
1/10W
R112
R113
R114
R115
R116
1-216-065-00
1-216-073-00
1-216-073-00
1-216-089-00
1-216-089-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
10K
10K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R117
R118
R119
R120
R121
1-216-041-00
1-216-089-00
1-216-077-91
1-249-417-11
1-249-413-11
RES-CHIP
RES-CHIP
RES-CHIP
CARBON
CARBON
470
47K
15K
1K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/4W
R142
R143
R159
1-216-051-00 RES-CHIP
1-216-065-00 RES-CHIP
1-216-097-11 RES-CHIP
(LX60S/LX70S)
1-216-049-00 RES-CHIP
(LX60S/LX70S)
1-216-073-00 RES-CHIP
(LX60S/LX70S)
1.2K
4.7K
100K
5%
5%
5%
1/10W
1/10W
1/10W
1K
5%
1/10W
10K
5%
1/10W
1-249-419-11 CARBON
(LX60S/LX70S)
1-216-089-00 RES-CHIP
1-216-089-00 RES-CHIP
1.5K
5%
1/4W
47K
47K
5%
5%
1/10W
1/10W
R160
R161
R162
R164
R165
7-11
MA-405
Ref. No.
Part No.
Description
R306
R308
R310
R311
R313
1-216-033-00
1-216-091-00
1-216-295-00
1-216-295-00
1-249-437-11
RES-CHIP
RES-CHIP
SHORT
SHORT
CARBON
220
56K
0
0
47K
5%
5%
1/10W
1/10W
R427
R440
R441
1-216-053-00 RES-CHIP
1-216-075-00 RES-CHIP
1-216-085-00 RES-CHIP
1.5K
12K
33K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/4W
RES-CHIP
RES-CHIP
CARBON
RES-CHIP
RES-CHIP
47K
33K
47K
47K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/10W
RES-CHIP
RES-CHIP
SHORT
CARBON
RES-CHIP
1K
1K
0
1K
1K
1/10W
1/10W
1-216-089-00
1-216-085-00
1-249-437-11
1-216-089-00
1-216-061-00
1-216-049-00
1-216-049-00
1-216-295-00
1-249-417-11
1-216-049-00
5%
5%
R314
R316
R318
R319
R321
R445
R500
R502
R503
R504
5%
5%
1/4W
1/10W
R323
R350
R351
R352
1-216-295-00
1-216-093-91
1-216-067-00
1-249-439-11
SHORT
RES-CHIP
RES-CHIP
CARBON
(LX40/LX50)
1-216-067-00 RES-CHIP
(LX40/LX50)
0
68K
5.6K
68K
5%
5%
5%
1/10W
1/10W
1/4W
R505
R507
R508
R509
R512
1-216-045-00
1-216-041-00
1-216-053-00
1-216-121-11
1-216-295-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
680
470
1.5K
1M
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
5.6K
5%
1/10W
2.2M
68K
5%
5%
1/10W
1/4W
1-249-413-11
1-216-037-00
1-249-407-11
1-249-408-11
1-216-021-00
CARBON
RES-CHIP
CARBON
CARBON
RES-CHIP
470
330
150
180
68
5%
5%
5%
5%
5%
1/4W
1/10W
1/4W
1/4W
1/10W
5.6K
5%
1/10W
R357
R358
1-216-129-00 RES-CHIP
1-249-439-11 CARBON
(LX40/LX50)
1-216-067-00 RES-CHIP
(LX40/LX50)
1-216-071-00 RES-CHIP
1-216-055-00 RES-CHIP
R513
R561
R562
R563
R564
8.2K
1.8K
5%
5%
1/10W
1/10W
R565
R570
R571
R572
R573
1-216-022-00
1-208-806-11
1-249-413-11
1-249-413-11
1-216-071-00
RES-CHIP
METAL CHIP
CARBON
CARBON
RES-CHIP
75
10K
470
470
8.2K
5%
0.5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/10W
R359
R362
R363
R364
R365
1-216-065-00
1-216-051-00
1-216-079-00
1-216-035-00
1-216-109-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
1.2K
18K
270
330K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R574
R575
R576
R577
1-216-049-00
1-249-425-11
1-216-097-11
1-216-097-11
R366
R367
R369
R370
R371
1-216-071-00
1-216-067-00
1-216-047-91
1-216-075-00
1-216-079-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
8.2K
5.6K
820
12K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R372
R373
560
1K
5%
5%
1/10W
1/4W
R380
R381
R382
1-216-043-91 RES-CHIP
1-249-417-11 CARBON
(LX40/LX50)
1-216-017-91 RES-CHIP
1-216-063-91 RES-CHIP
1-217-671-11 RES-CHIP
47
3.9K
1
5%
5%
5%
R383
R401
R402
R407
R409
1-216-031-00
1-216-025-11
1-249-437-11
1-216-013-00
1-216-053-00
RES-CHIP
RES-CHIP
CARBON
RES-CHIP
RES-CHIP
180
100
47K
33
1.5K
R410
R411
R412
R413
R415
1-216-057-00
1-216-059-00
1-216-075-00
1-216-077-91
1-216-053-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
R416
R417
R418
R422
R423
1-216-053-00
1-216-057-00
1-216-059-00
1-249-417-11
1-249-417-11
R424
R425
R353
R354
R355
R356
Remarks
Ref. No.
Part No.
Description
Remarks
1K
4.7K
100K
100K
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
R601
RES-CHIP
CARBON
RES-CHIP
RES-CHIP
(LX60S/LX70S)
1-214-949-21 METAL
3.3M
1%
1/2W
R602
R603
R604
R605
R606
1-247-883-00
1-247-891-00
1-249-430-11
1-249-419-11
1-215-444-00
CARBON
CARBON
CARBON
CARBON
METAL
150K
330K
12K
1.5K
9.1K
5%
5%
5%
5%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
1/10W
1/10W
1/10W
R607
! R611
R612
R613
R614
1-249-428-11
1-260-364-11
1-208-789-11
1-249-406-11
1-216-655-11
CARBON
CARBON
METAL CHIP
CARBON
METAL CHIP
8.2K
1M
2K
120
1.5K
5%
5%
0.5%
5%
0.5%
1/4W
1/2W
1/10W
1/4W
1/10W
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/10W
R615
R616
R617
R618
R621
1-216-057-00
1-249-401-11
1-249-417-11
1-249-409-11
1-249-429-11
RES-CHIP
CARBON
CARBON
CARBON
CARBON
2.2K
47
1K
220
10K
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
1/4W
1/4W
2.2K
2.7K
12K
15K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R622
R623
! R640
! R641
R643
1-216-430-11
1-247-843-11
1-219-153-11
1-219-153-11
1-216-353-00
METAL OXIDE
CARBON
FUSIBLE
FUSIBLE
METAL OXIDE
390
3.3K
10
10
2.2
5%
5%
5%
5%
5%
1W
1/4W
1/4W
1/4W
1W
RES-CHIP
RES-CHIP
RES-CHIP
CARBON
CARBON
1.5K
2.2K
2.7K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/4W
R647
R648
R649
R651
R669
1-215-465-00
1-216-057-00
1-216-017-91
1-215-459-00
1-216-061-00
METAL
RES-CHIP
RES-CHIP
METAL
RES-CHIP
68K
2.2K
47
39K
3.3K
1%
5%
5%
1%
5%
1/4W
1/10W
1/10W
1/4W
1/10W
1-249-417-11 CARBON
1-216-095-00 RES-CHIP
1K
82K
5%
5%
1/4W
1/10W
R676
R678
R679
1-249-417-11 CARBON
1-249-409-11 CARBON
1-249-409-11 CARBON
1K
220
220
5%
5%
5%
1/4W
1/4W
1/4W
7-12
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
MA-405
Ref. No.
Part No.
Description
Remarks
R680
R701
1-249-417-11 CARBON
1-249-417-11 CARBON
1K
1K
5%
5%
1/4W
1/4W
R702
R703
R704
R709
R710
1-216-061-00
1-249-412-11
1-216-043-91
1-216-049-00
1-216-049-00
RES-CHIP
CARBON
RES-CHIP
RES-CHIP
RES-CHIP
3.3K
390
560
1K
1K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R711
R712
! R723
R724
1-216-049-00
1-216-295-00
1-240-307-81
1-216-113-00
RES-CHIP
SHORT
FUSIBLE
RES-CHIP
1K
0
560
470K
5%
1/10W
5%
5%
1/4W
1/10W
Ref. No.
1-762-108-11
1-771-155-11
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, PUSH (1 KEY) REC PROOF
SWITCH, ROTARY MODE
SWITCH, TACT CHANNEL/TRACKING+
SWITCH, TACT CHANNEL/TRACKINGSWITCH, TACT EASY SET-UP
S408
S409
S410
S411
S412
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (0 REW)
SWITCH, TACT (P PAUSE)
SWITCH, TACT (· PLAY)
SWITCH, TACT (p STOP)
SWITCH, TACT (r REC)
S413
S429
S701
1-762-196-21 SWITCH, TACT () FF)
1-762-196-21 SWITCH, TACT (SEARCH)
1-571-588-11 SWITCH, SLIDE RF UNIT (CH3˜CH4)
1-757-551-11
1-500-477-11
4-6759-621-A
1-698-971-11
X-3947-577-1
FLAT CABLE FAC-009
FLAT CABLE FE HEAD
HEAD BLOCK ASSY, ACE
MOTOR DC
MOTOR ASSY, CAM
8-839-049-53 DRUM ASSY,DZH-0A2A/Z-RP
(LX40/LX50)
8-839-047-53 DRUM ASSY, DZH-0A0A/Z-RP
(LX60S/LX70S)
ACCESSORIES
***********
1-569-008-21 ADAPTOR, CONVERSION 2P
(LX50:CL,CS/LX70S:CL,CS)
1-575-795-61 CORD, CONNECTION (LX50/LX60S/LX70S)
1-696-592-41 CORD, CONNECTION (NTSC)
(LX40/LX60S/LX70S)
1-476-436-11 COMMANDER, STANDARD(RMT-V293A)
(LX40/LX50)
1-476-437-11 COMMANDER, STANDARD(RMT-V294A)
(LX60S/LX70S)
3-709-432-11 COVER, REMOTE CONTROL BATTERY
3-065-284-12 MANUAL, INSTRUCTION
1-431-097-11 TRANSFORMER, BIAS OSCILLATION
1-435-790-11 TRANSFORMER, CONVERTER
<TUNER>
TU701
Remarks
1-777-852-12 CORD, POWER
(LX40/LX50:MX,PA,PC,VZ/
LX60S/LX70S:MX,PA,PC,VZ)
1-777-854-22 CORD, POWER
(LX50:CL,CS/LX70S:CL,CS)
1-757-552-12 FLAT CABLE FDM-010
1-757-556-11 FLAT CABLE FFJ-004
1-757-550-11 FLAT CABLE FMD-021
<TRANSFORMER>
T380
! T600
Description
MISCELLANEOUS
**************
<SWITCH>
S101
S102
S404
S405
S406
Part No.
1-693-532-21 TUNER (BTF-3MA413)
<VARISTOR>
HARDWARE LIST
**************
! VDR600 1-801-267-31 VARISTOR TNR10V431K660
(LX50:CL,CS/LX70S:CL,CS)
! VDR600 1-804-048-31 VARISTOR (240NS10D)
(LX40/LX50:MX,PA,PC,VZ/
LX60S/LX70S:MX,PA,PC,VZ)
<VIBRATOR>
X160
X161
X201
1-767-857-11 VIBRATOR, CRYSTAL
1-579-463-11 VIBRATOR, CRYSTAL
1-577-380-11 VIBRATOR, CRYSTAL
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
14.3181MHz
32.768KHz
3.579545MHz
7-13E
7-13
#1
#2
#3
#4
3-710-901-01
3-970-608-21
3-974-556-11
3-979-508-01
4-921-277-41
SCREW, TAPPING
SUMITITE (B3), +BV
+HEXA TT2.6X9 (TAPER)
SCREW +HEXA TP SW3X8
SCREW (B2.6X8), TAPPING, BIND
7-685-648-79
7-685-646-79
7-682-647-09
7-685-133-19
SCREW +BVTP
SCREW +BVTP
SCREW +P3X6
SCREW +P2.6X6
3X12 TYPE2 IT-3
3X8 TYPE2 IT-3
TYPE2 NON-SLIT
Ref. No.
Part No.
Description
Remarks
Ref. No.
7-14
Part No.
Description
Remarks
SLV-LX40/LX50/LX60S/LX70S
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Sony Corporation
9-921-786-11
NETWORK ENTERTAINMENT GROUP
–7-15
86 –
Description
Remarks
20001B0800-1
 2001. 2
Published by Quality Assurance Dept.