Download SERVICE MANUAL
Transcript
SERVICE MANUAL MODEL KLV-26S550A KLV-32S530A COMMANDER DEST. RM-GA016 & GE, India, ME, RM-GA016W Philippines, Russia, South Africa, Thailand MODEL COMMANDER KLV-32S550A/L RM-GA016 & GE, ME, Philippines, (Blue) RM-GA016W Russia, South Africa KLV-32S550A/T RM-GA016 & ME, Thailand RM-GA016W KLV-32S550A EX2T CHASSIS RM-GA016 & GE, India, Iran, ME, RM-GA016W New Zealand, Philippines, Russia, South Africa, Thailand Tunisia (Brown) KLV-37S550A KLV-26S550A RM-GA016 & GE, ME, Philippines, RM-GA016W Russia, South Africa RM-GA016 & GE, India, Iran, ME, RM-GA016W Thailand, Tunisia Philippines, Russia, KLV-32S550A RM-GA016 KLV-37S550A DEST. RM-GA016W LCD COLOR TV KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W TABLE OF CONTENTS Section Title Page 1. SAFETY NOTES 1-1. Caution Handling of LCD Panel ..................................... 3 1-2. Safety Check Out ............................................................. 3 1-3. Leakage Test .................................................................... 3 1-4. WARNING ! .................................................................... 3 1-5. Lead Free Information ..................................................... 4 2. SELF DIAGNOSTIC FUNCTION 2-1. Overview of Control Buttons .......................................... 5 2-2. LED Display Specification .............................................. 5 2-3. LED Display Control ....................................................... 5 2-4. LED Pattern ..................................................................... 5 2-5. Viewing the Service Diagnosis Display .......................... 5 2-6. Standby LED Error Display ............................................ 6 2-7. Triage Chart ..................................................................... 6 Section Title Page 7. DIAGRAMS 7-1. Block Diagram ............................................................... 24 7-1-1. BT2 Board ......................................................... 24 7-1-2. GT3 Board (Except 37S550A) .......................... 27 7-1-3. HT1 Board ......................................................... 29 7-2. Connector Diagram ....................................................... 30 7-2-1. KLV-26S550A ................................................... 30 7-2-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T ......................................................... 31 7-2-3. KLV-37S550A ................................................... 31 7-3. Circuit Board Location .................................................. 32 7-3-1. KLV-26S550A ................................................... 32 7-3-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T ......................................................... 32 7-3-3. KLV-37S550A ................................................... 33 7-4. Schematic Diagram Information ................................... 34 7-5. Printed Wiring Boards ................................................... 34 7-6. Semiconductor ............................................................... 34 3. TROUBLE SHOOTING .................................................. 7 4. DISASSEMBLY 4-1. KLV-26S550A ................................................................. 8 4-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T ...... 9 4-3. KLV-37S550A ............................................................... 10 5. WIRE DRESSING 5-1. KLV-26S550A ............................................................... 12 5-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T .... 15 5-3. KLV-37S550A ............................................................... 18 8. EXPLODED VIEWS 8-1. KLV-26S550A ............................................................... 35 8-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T .... 37 8-3. KLV-37S550A ............................................................... 39 9. ELECTRICAL PARTS LIST 9-1. KLV-26S550A ............................................................... 41 9-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T .... 41 9-3. KLV-37S550A ............................................................... 42 OPERATING INSTRUCTIONS 6. SERVICE ADJUSTMENTS 6-1. Accessing Diagnostic Menu .......................................... 21 6-2. Viewing the Service Mode Display .............................. 21 6-3. Control Keys Via Remote Commander ......................... 21 6-4. Adjustment Method ....................................................... 21 6-5. Table 1 ............................................................................ 23 6-6. Board & Panel Replacement ......................................... 23 –2– KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 1 SAFETY NOTES 1-1. Caution Handling of LCD Panel When installing the LCD Panel, make sure you are grounded with a wrist band. When installing the LCD Panel on the wall, the panel must be secured using the 4 mounting holes on the rear cover. 1) Do not press the panel or frame edge to avoid the risk of electric shock. 2) Do not scratch or press on the panel with any sharp objects. 3) Do not leave the module in high temperature or in areas of high humidity for an extended period of time. 4) Do not expose the LCD panel to direct sunlight. 5) Avoid contact with water. It may cause short circuit within the module. 6) Disconnect the AC adapter when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms) 7) Always clean the LCD panel with a soft cloth material. 8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short circuit. 9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS). 1-3. Leakage Test The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis must not exceed 0.5mA (500 microamperes). Leakage current can be measured by any one of the three methods:1. A commercial leakage tester such as the SIMPSON 229 or RCA WT-540A. Follow the manufacturers instructions to use those instructions. 2. A battery-operated AC milliampmeter. The DATA PRECISION 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery operated AC voltmeter. The 'limit' indication is 0.75V so analog meters must have an accurate low voltage scale. The SIMPSON'S 250 and SANWA SH-63TRD are examples of passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2 VAC range are suitable. (see Figure 1.) To Exposed Metal Parts on Set 1-2. Safety Check-Out After correcting the original service problem, perform the following safety checks before releasing the set to the customer:- 0.15 μF 1) Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges. 2) Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3)Check all control knobs, shields, covers, ground straps and mounting hardware have been replaced. Be absolutely certain you have replaced all the insulators. 4) Look for unauthorized replacement parts, particularly transistors that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5) Look for parts which, though functioning show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6) Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7) Check the antenna terminals, metal trim, "metallized" knobs, screws and all other exposed metal parts for AC leakage. Check leakage test as described next. 1.5 k1 AC Voltmeter (0.75 V) Earth Ground Figure 1. AC voltmeter to check AC leakage 1-4. WARNING ! SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE EXPLODED VIEWS ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED. –3– KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 1-5. Lead Free Information The circuit boards used in these models have been processed using Lead Free Solder. The boards are identified by the LF logo located close to the board designation. Figure 2: LF logo Figure 3: LF logo on circuit board The servicing of these boards requires special precautions. It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints. Lead Free Solder is available under the following part numbers:Part number Diameter Remarks 7-640-005-19 0.3mm 0.25Kg 7-640-005-20 0.4mm 0.50Kg 7-640-005-21 0.5mm 0.50Kg 7-640-005-22 0.6mm 0.25Kg 7-640-005-23 0.8mm 1.00Kg 7-640-005-24 1.0mm 1.00Kg 7-640-005-25 1.2mm 1.00Kg 7-640-005-26 1.6mm 1.00Kg Due to high melting point of Lead Free Solder, the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com –4– KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 2 SELF DIAGNOSTIC FUNCTION 2-1. Overview of Control Buttons 2-4. LED Pattern When safety shutdown occurs, Standby LED display reports the cause by using the blinking patterns as indicated below. 2.0 sec 2.0 sec 0.3 sec 0.3 sec Example: Remote sensor Timer indicator Standby indicator The figure above shows LED display when SHUTDOWN is caused by audio failure. It repeats flashing for a specified number of times in 0.3sec/ cycle and has a 2 seconds interval of lighting off. Please note that a 2 seconds interval of lighting off is fixed regardless of abnormal state types. Power indicator Power indicator 2-5. Viewing the Service Diagnosis Display 1. While TV on standby mode, press the following sequence on the Remote commander. PROG Channel On screen display Volume S Menu 2-2. LED Display Specification POWER Remark Description Timer Amber : One LEDs 0 0 0 0 0 C H E 2 M 4 5 0 6 0 0 0 0 002: LED blinking times MAIN_POWER_ERROR: Detection name 00: Error Count (00-99) C K A I N _ P O W E R _ E R R V _ P O W E R _ E R R O R B A C K _ L I G H T _ E R R 7 T E M P _ E R R O R 8 A U D I O _ E R R O OFF 2 3 4 5 - 0 9 8 7 6 - 0 1 2. To Exit, press the <I/1> key. Amber lights during Timer activation. Display Power LED Standby LED POWER ON Green lights Failure F Red lights during standby. 2-3. LED Display Control STANDBY L R O O R R 0 0 0 0 0 0 0 0 0 0 12345: Total operation time by hour (0-65535) 09876: Boot count (0-65535) 01234: Panel operation time by hour (0-65535) 1 Red: One LED Status E Green: One LED Green lights at power ON. STANDBY POWER Volume (-) (if wrong key is pressed or passed 3 seconds during each process, cancel entering the self-diagnosis display.) Input Select LED Type Channel 5 Remark OFF Microcomputer is in a normal state. Red lights Microcomputer is in a sleep state. Classify the trouble causes by the no. of red blinking. –5– 2 3 4 KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 2-6. STANDBY LED ERROR DISPLAY Blinking times Detection items Countermeasure Replace either/both z BT2 board z G4T board (37”) z GT3 board (26”/32”) 2 Main power failure 4 5V power failure 8 Audio failure Replace either/board. z BT2 board z G4T board (37”) z GT3 board (26”/32”) z Speaker z Woofer 6 Back light failure Replace either/board. z BT2 board z G4T board (37”) z GT3 board (26”/32”) 7 Internal temperature failure Replace either/both z G4T board (37”) z GT3 board (26”/32”) Replace BT2 board. Note: Each of the above blinking repeats every 2 seconds. 2-7. Triage Chart Please refer page 46 for Triage Chart. –6– KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 3 TROUBLE SHOOTING Please refer page 47~50 for Trouble Shooting. –7– KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 4 DISASSEMBLY Note: 1) The illustrations provided in this section might have slight difference from actual sets. 2) Refer to Removal & Installation of Rear Cover and Switch Unit Procedure in Section 1 Safety Notes. 4-1. KLV-26S550A 4-1-1. Rear Cover Removal 4-1-2. Stand Assy Removal 1 Four screws (+PSW M5 X 16) 3 Two screws (+BVTP 3 X 12) 2 Two screws (+PSW M3 X 5) 2 Stand assy 1 Twelve screws (BVTP2 4 X 16) 4 Two screw (+PSW M4 X 8) 5 Lift to remove Rear Cover 4-1-3. Switch Unit Removal 4-1-4. GT3 Board Removal 1 Six screws (+BVST 3 X 8) 2 Three connectors 3 Switch unit 2 Lift tabs to remove board 3 GT3 board 1 4-1-5. BT2 Board Removal 3 Side Jack Bracket 4-1-6. Speaker and Bracket Removal 3 One screw (+BVTP2 4 X 16) 4 Nine screws (+BVST 3 X 8) 1 One screw (+PSW M4 X 8) 4 Speaker Baffle 1 One screws (+PSW M4 X 8) 2 Frame Spine 6 BT2 board 6 Loudspeaker (4 X 10cm) 5 Five connectors 5 Four screws (+BVTP2 4 X 16) 7 Two screws (+BVTP 3 X 12) 8 Main Frame 2 Under Cover 9 Four screws (+BVTP2 4 X 16) 7 One screw (+BVTP2 4 X 16) 8 Speaker Baffle q; Loudspeaker (4 X 10cm) qa Bezel assy –8– KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 4-1-7. Vesa Frame Removal 4-1-8. LCD Panel Bezel Assy Removal 2 Two screws (+PSW M4 X 8) 1 One screw (+PSW M4 X 8) 2 Harness with connector 3 Frame Spine (R) 1 Two screws (+BVTP2 4 X 16) 3 LCD panel 5 One screw (+BVTP 3 X 12) 6 HT1 Board 4 Frame Bottom 4 Bezel assy 4-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T 4-2-2. Stand Assy Removal 4-2-1. Rear Cover Removal 3 Three screws (+BVTP 3 X 12) 1 Four screws (+PSW M5 X 16) 2 Two screw (+PSW M3 X 5) 2 Stand assy 1 Twelve screws (BVTP2 4 X 16) 4 Two screw (+PSW M4 X 8) 5 Lift to remove Rear Cover 4-2-3. Switch Unit Removal 4-2-4. GT3 Board Removal 1 Six screws (+BVST 3 X 8) 2 Lift tabs to remove board 2 Three connectors 3 Switch unit 3 GT3 board 1 –9– KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 4-2-5. BT2 Board Removal 1 Side Jack Bracket Assy 4-2-6. Speaker and Bracket Removal 2 Nine screws (+BVST 3 X 8) 3 One screw (+BVTP2 4 X 16) 4 Speaker Baffle 4 BT2 board 5 One screw (+BVTP2 3 X 12) 2 Under Cover 5 Loudspeaker (3.4 X 17.5cm) 3 Five connectors 1 One screw (+PSW M4 X 8) 9 Four screws (+BVTP2 4 X 16) 7 One screw (+BVTP2 4 X 16) 8 Speaker Baffle 6 Four screws (+BVTP2 4 X 16) 6 Main Bracket q; Loudspeaker (3.4 X 17.5cm) qa Bezel assy 4-2-8. LCD Panel Bezel Assy Removal 4-2-7. Vesa Frame Removal 1 One screw (+PSW M4 X 8) 2 Harness with connector 2 One screw (+PSW M4 X 8) 6 One screw (+PSW M4 X 8) 4 Frame Spine (L) 1 Two screws (+BVTP2 4 X 16) 7 Frame Spine (R) 5 One screw (+PSW M4 X 8) 3 Two screws (+BVTP 4 X 16) 3 LCD panel 8 One screw (+PSW M4 X 8) qa One screw (+BVTP 3 X 12) 9 One screw (+PSW M4 X 8) qs HT1 Board 0 Frame Bottom 4 Bezel assy 4-3. KLV-37S550A 4-3-1. Rear Cover Removal 2 Two screws (+BVTP 3 X 12) 4-3-2. Stand Assy Removal 1 Four screws (+PSW M5 X 16) 3 Two screws (+PSW M3 X 5) 4 Four screws (+PSW 4 X 16) 2 Stand assy 1 Twelve screws (BVTP2 4 X 16) 5 Lift to remove Rear Cover – 10 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 4-3-3. Switch Unit Removal 4-3-4. G4T Board Removal 2 Three connectors 2 Lift tabs to remove board 1 Four screws (+BVST 3 X 8) 3 Switch unit 3 G4T board 1 4-3-6. Speaker and Bracket Removal 4-3-5. BT2 Board Removal 1 Side Jack Bracket Assy 1 One screw (+PSW M4 X 8) 2 Nine screws (+BVST 3 X 8) 3 One screw (+BVTP2 4 X 16) 4 Speaker Baffle 4 BT2 board 6 Loudspeaker (3.4 X 17.5cm) 3 Five connectors 5 One screw (+BVTP2 3 X 12) 5 Four screws (+BVTP2 4 X 16) 6 Main Bracket 2 Under Cover 9 Four screws (+BVTP2 4 X 16) 7 One screw (+BVTP2 4 X 16) 8 Speaker Baffle q; Loudspeaker (3.4 X 17.5cm) qa Bezel assy 4-3-7. Vesa Frame Removal 4-3-8. LCD Panel Bezel Assy Removal 2 Harness with connector 1 One screw (+PSW M4 X 8) 2 One screw (+PSW M4 X 8) 4 Frame Spine (L) 5 One screw (+PSW M4 X 8) 0 One screw (+BVTP 3 X 12) qa HT1 Board qs Guide Light 3 Two screw (+BVTP 4 X 16) 6 One screw (+PSW M4 X 8) 1 Four screws (+BVTP2 4 X 16) 3 LCD panel 7 Frame Spine (R) 8 Two screws (+BVTP2 4 X 16) 9 Frame Bottom 4 Bezel assy – 11 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 5 WIRE DRESSING CAUTION : 1. Do not overpull the wires during dressing --> avoid disconnection of wires. 2. Make sure wires are kept away from sharp edges, heatsinks & other high-temperature parts. Legend: Hook 5-1. KLV-26S550A 5-1-1. Wire Dressing overview. CISPR model Non CISPR model P5-6 P5-6 P4 P4 P P8 P7 P 5-1-2. Insert Connector Assy 10p and Speaker Connector Assy 4P. 3) Insert Connector Assy 10P to SW unit. Attach SW unit to Bezel and dress with Tape (LCD) (X2). 1) Insert Connector Assy 10P to HT1 PWB. Attach HT1 PWB to Light Guide on Bezel. 2) Insert SP Conn Assy 4P to speaker as shown. Attach Sheet Core, C (X1) as shown. Left speaker 1 Conn Assy 10P (HT1 PWB) behind speaker Attach Sheet Core, C to SP Conn Assy 4P; Lead Assy, Earth and conn Assy 10P (X1). Use daturm line to position Sheet core, C. 2 – 12 – 1 Left speaker Dress Conn Assy 10P (SW unit) using Tape (LCD) (X2). KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-1-3. Insert Connector Assy 14P 1) Attach Sheet Core, C (X2) to frame bottom as shown. 2) Insert Conn Assy 14P to inverter and GT3 PWB as shown. Attach Sheet Core, C as shown. Dress SP Conn Assy 4P; Lead Assy, Earth and Conn Assy 10P Wires along this path (behind Under cover) and below raised area of frame bottom 1 1 A Attach Sheet Core, C towards the left side of frame bottom. Dress SP Conn Assy 4P and Conn Assy 10P using Sheet Core, C. Use datum line to position Sheet Core, C. 2 Frame bottom Insert Conn Assy 14P to GT3 PWB. Attach Sheet Core, C (X1). For Non-CISPR models For CISPR models 3) Attach Sheet Core, C (X2) to LVDS harness. 4) Attach Sheet Core, C to Connector Assy 14P and LVDS harness. 3) Attach Tape, Shield followed by Sheet Core, C on to LVDS harness. 4) Insert screw on to earth clamp on LVDS harness. 5) Attach Sheet Core, C to Connector Assy 14P and LVDS harness. 6) Attach Sheet Core, C on to LVDS harness 4 3 Attach Sheet Core, C to conn Assy 14P and LVDS harness 5 NonCISPR model Attach Sheet Core, C to Conn Assy 14P and LVDS 4 Attach Sheet Core, C (X2) to LVDS harness. 3 Attach Sheet Core, C to LVDS harness. Note: When inserting LVDS harness to panel, make sure it is fully inserted and in the correct direction as shown. OK NG 5-1-4. Attach Sheet Core, C (X3) to main bracket as shown. Attach Sheet Core, C to Conn Assy 14P and SP Conn Assy 4P. Dress Conn Assy 10P; Lead Assy, Earth and SP Conn Assy 4P together. Dress SP Conn Assy 4P to the left of this line (edge of BT2 PWB) 1 – 13 – Insert screw on to earth clamp on LVDS harness. Attach Tape, Shield followed by Sheet Core, C to LVDS harness. 6 Attach Sheet Core, C to main bracket (X3). CISPR model KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-1-5. Power Cord Wire Dressing CISPR model Non CISPR model 1) Install AC cord holder to AC power cord at specified position as shown. 2) Then install the AC power cord with holder on to under cover. 3) Lastly, dress AC power cord using pin, wire A6101 as shown. 4) Keep the AC power cord away from surrounding parts. AC Cord Holder 1) Install Ferrite core to AC power cord at specified position as shown. 2) Install AC cord holder to AC power cord at specified position as shown. 3) Attach Sheet Core, E to Ferrite Core and frame bottom. 4) Then install the AC power cord with holder on to under cover. 5) Lastly, dress AC power cord using pin, wire A6101 as shown. 6) Keep the AC power cord away from surrounding parts. Ferrite Core 1 110 ± 5mm 4 150 ± 5mm 2 Make sure distance of >4mm is kept from F6102, C6102 and C6111 leads to single insulated portion of AC power cord (Blue and Brown wire). This can be controlled by using pin, wire A6101 to dress AC power cord away from conductive parts. 2 70± AC Cord 4mm 4mm 3 3 Attach Sheet Core, E to Ferrite Core. Dress AC power cord using pin, wire A6101. AC power cord's wire is facing to the right Insert the AC cord holder on to under cover Caution: 1. Ensure that AC power cord is not stressed whilst inserting it into AC cord bracket. Dress AC power cord using pin, wire A6101. 5 4mm 4mm 4mm 6 4 – 14 – Insert the AC cord holder on to under cover Make sure distance of >4mm is kept from F6102, C6102 and C6111 leads to single insulated portion of AC power cord (Blue and Brown wire). This can be controlled by using pin, wire A6101 to dress AC power cord away from conductive parts. KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T 5-2-1. Wire Dressing overview . CISPR model Non-CISPR model P6 P4-5 P6 P4-5 P3 P3 P8 P7 5-2-2. Insert Connector Assy 10P and SP Connector Assy 4P Left Speaker Right Speaker 1) Insert Connector Assy 10P to HT1 PWB. Attach HT1 PWB to Light Guide on Bezel. 2) Insert SP Conn Assy 4P to speaker as shown. Attach Sheet Core, C (X1) as shown. 1) Insert Connector Assy 10P to SW unit. Attach SW unit to Bezel and dress with Tape (LCD) (X2). 2) Insert SP Conn Assy to speaker and attach Sheet Core, C as shown. 3) Attach Sheet Core, C to Frame Bottom as shown. Left speaker 1 Conn Assy 10P (HT1 PWB) behind speaker 2 Right speaker Dress SP Conn Assy 4P and Conn Assy 10P using Sheet Core, C. Use datum line to position Sheet Core , C. Do not cover speaker hole 2 Attach Sheet Core, C to SP Conn Assy 4P and Conn Assy 10P (X1). Use datum line to position Sheet Core, C. Do not cover p speaker hole with Sheet Core, C. 1 Conn Assy 10P (HT1 PWB) behind speaker Do not cover speaker hole – 15 – Dress Conn Assy 10P (SW unit) using Tape (LCD) (X2). 3 Attach Sheet Core, C to SP Conn Assy 4P and Conn Assy 10P to Frame Bottom KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-2-3. Attach C Sheet Core and Insert Connector Assy 14P 1) Attach Sheet Core, C to frame bottom as shown. 2) Attach Sheet Core, C to main bracket as shown. 3) Insert Conn Assy 14P to inverter and GT3 PWB as shown. Attach Sheet Core, C as shown. Attach Sheet Core, C to Frame Bottom (X1). 1 Frame Bottom Dress SP Conn Assy 4P; Lead Assy, Earth and Conn Assy 10P wires w along this path (behind under cover) and below raised area of Frame Bottom. Attach Sheet Core, C to Main Bracket (X1). 2 Dress Lead Assy, Earth along this path 3 Insert Conn Assy 14P to GT3 PWB. Attach Sheet Core, C (X1) For all models 3) Attach Sheet Core, C to LVDS harness. 4) Attach Sheet Core, C to Connector Assy 14P and LVDS harness. For CISPR models only 5) Insert screw on to earth clamp on LVDS harness. Attach Sheet Core, C (X1) to Conn Assy 14P and LVDS harness on frame spine. 4 5 4 Attach Sheet Core, C (X1) to Conn Assy 14P and LVDS harness on frame spine. 3 Insert screw on to earth clamp on LVDS harness. 3 Attach Sheet Core, C (X1) to LVDS harness. Attach Sheet Core, C (X1) to LVDS harness. 2 CISPR model Non-CISPR model Note: When inserting LVDS harness to panel, make sure it is fully inserted and in the correct direction as shown. OK NG 5-2-4. Attach C Sheet Core to Main Bracket and Frame Bottom 1) Attach Sheet Core, C (X3) to main bracket as shown. 2) Attach Sheet Core, C (X1) to frame bottom as shown. 3) Attach Sheet Core, C (X1) to main bracket as shown. Dress Conn Assy 14P and SP Conn Assy 4P together. Dress SP Conn Assy 4P using Sheet Core, C. Dress SP Conn Assy 4P to the left of this line (edge of BT2 PWB) 1 Attach Sheet Core, C to main bracket (X3). Dress Conn Assy 10P and SP Conn Assy 4P together. 2 Dress SP Conn Assy 4P and Conn Assy 10P together using Sheet Core, C to frame bottom. 3 Dress Lead Assy, Earth to main bracket using Sheet Core, C. – 16 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-2-5. AC Power Cord Wire Dressing Non-CISPR model 1) Install AC cord holder to AC power cord at specified position as shown. 2) Then install the AC power cord with holder into under cover. 3) Lastly, dress AC power cord using pin, wire A6101 as shown. 4) Keep the AC power cord away from surrounding parts. Make sure distance of >4mm is kept from F6102 and C6111 lead to single insulated portion of AC power cord (Blue and Brown wire). This can be controlled by using pin, wire A6101 to dress AC power cord away from conductive parts. Non-CISPR model 4mm 1 AC Cord Holder 4mm 150 ± 5mm 3 Dress AC power cord using pin, wire A6101. Keep AC cord away from fuse F6102 (4mm or more). 2 Inset the AC Cord Holder on to Under Cover. Caution: 1. Ensure that AC power cord is not stressed whilst inserting it into AC cord bracket. CISPR model 1) Install Ferrite core to AC power cord at specified position as shown. 2) Install AC cord holder to AC power cord at specified position as shown. 3) Then install the AC power cord with holder into under cover. 4) Attach Sheet Core, E to Ferrite Core. Place AC cord underneath frame spine. 5) Dress AC power cord using pin, wire A6101 as shown. 6) Lastly, keep the AC power cord away from surrounding parts. 4 Attach Sheet Core, E to Ferrite Core. 5 Dress AC power cord using pin, wire A6101. 1 4mm 4mm 4mm 2 Ferrite Core 110± 5mm 200 ± 5mm AC Cord Holder AC cord is underneath frame spine. 3 Insert the AC cord holder on to under cover CISPR model 6 Make sure distance of >4mm is kept from F6102 and C6111 lead to single insulated portion of AC power cord (Blue and Brown wire). This can be controlled by using pin, wire A6101 to dress AC power cord away from conductive parts. – 17 – Caution: 1. Ensure that AC power cord is not stressed whilst inserting it into AC cord bracket. KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-3. KLV-37S550A 5-3-1. Wire Dressing overview. CISPR model Non-CISPR model P4 P5-6 P3-4 P P3-4 P5-6 P4 P 5-3-2. Insert Connector Assy 10P and SP Connector Assy 4P 1) Insert Connector Assy 10P to HT1 PWB. Attach HT1 PWB to Light Guide on Bezel. 2) Insert SP Conn Assy 4P to speaker as shown. Attach Sheet Core, C (X1) as shown. Left speaker 1 Conn Assy 10P (HT1 PWB) behind speaker Attach Sheet Core, C to SP Conn Assy 4P and Conn Assy 10P. Use datum line to position Sheet Core, C. Do not cover speaker hole with Sheet Core, C. 2 Conn Assy 10P (HT1 PWB) behind speaker Do not cover speaker hole 5-3-3. Insert Connector Assy 10, SP Connector Assy and attach C Sheet Core 1) Insert Connector Assy 10P to SW unit. Attach SW unit to Bezel and dress with Tape (LCD) (X2). 2) Insert SP Conn Assy to speaker and attach Sheet Core, C as shown. 3) Attach Sheet Core, C to panel as shown. Right speaker 2 Dress SP Conn Assy 4P and Conn Assy 10P using Sheet Core, C. Use datum line to position Sheet Core, C. Do not cover speaker hole with Sheet Core, C. Keep wire away from screw hole --> Prevent wire from being sandwiched by screw when docking rear cover. Do not cover speaker hole 1 Dress Conn Assy 10P (SW unit) using Tape (LCD) (X2). 3 – 18 – Attach Sheet Core, C to SP Conn Assy 4P and Conn Assy 10P to panel. Dress wires towards bottom of panel as shown. KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-3-4. Attach C Sheet Core and Insert Connector Assy 14P 1) Attach Sheet Core, C (X3) to frame bottom as shown. 2) Insert Conn Assy 14P to inverter and G4T PWB as shown. Attach Sheet Core, C as shown. 1 Do not cover screw hole with Sheet Core, C Attach Sheet Core, C to frame bottom (X3). 2 Frame bottom Dress SP Conn Assy 4P and Conn Assy 10P wires along this path (behind under cover) and below raised area of bottom bracket. Insert Conn Assy 14P to G4T PWB. Attach Sheet Core, C (X1). For all models 3) Attach Sheet Core, C to LVDS harness. 4) Attach Sheet Core, C to Connector Assy 14P and LVDS harness on frame spine. For CISPR models only Do not cover screw hole with 5) Insert screw on to earth clamp on LVDS harness. Sheet Core, C. Keep LVDS harness away from screw hole. Non-CISPR model 3 Do not cover screw hole with Sheet Core, C. Keep LVDS harness away from screw hole. 5 3 Attach Sheet Core, C (X1) to LVDS harness. 4 Attach Sheet Core, C (X1) to LVDS harness. Attach Sheet Core, C (X1) to Conn Assy 14P and LVDS harness. 4 NG 5-3-5. Attach C Sheet Core and Insert Connector Assy 14P 1) Attach Sheet Core, C (X3) to main bracket as shown. 2) Attach Sheet Core, C (X1) to panel as shown. 3) Attach and screw Lead Assy, Earth on to G4T PWB as shown. 4) Attach Sheet Core, C (X1) to main bracket as shown. Attach Sheet Core, C to Conn Assy 13P, Conn Assy 14P and SP Conn Assy 4P. Dress SP Conn Assy 4P to the left of this line (edge of BT2 PWB) Dress Conn Assy 10P and SP Conn Assy 4P together. 1 3 Attach and screw Lead Assy, Earth. 2 Attach Sheet Core, C to main bracket (X3). 4 Dress SP Conn Assy 4P and Conn Assy 10P together using Sheet Core, C to panel. 4 Attach Sheet Core, C to Lead Assy, Earth on main bracket. – 19 – Insert screw on to earth clamp on LVDS harness. Attach Sheet Core, C (X1) to Conn Assy 14P and LVDS harness. Note: When inserting LVDS harness to panel, make sure it is fully inserted and in the correct direction as shown. OK CISPR model KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 5-3-6. Install AC Cord Holder and Power Cord Non-CISPR model 1) Install AC cord holder to AC power cord at specified position as shown. 2) Then install the AC power cord with holder into under cover. 3) Keep the AC power cord away from surrounding parts. 3 1 Make sure distance of >4mm is kept from F101 and NR101 lead to single insulated portion of AC power cord (Blue and Brown wire). Dress AC power cord away from conductive parts. 2 AC Cord Holder 4mm 130 ± 5mm 4mm Insert the AC cord holder on to under cover CISPR model 1) Install Ferrite core to AC power cord at specified position as shown. 2) Install AC cord holder to AC power cord at specified position as shown. 3) Attach Sheet Core, E to Ferrite Core and frame bottom. 4) Then install the AC power cord with holder into under cover. 5) Keep the AC power cord away from surrounding parts. 1 Ferrite Core 70± 5mm 170 ± 5mm 2 AC Cord Holder 5 3 Make sure distance of >4mm is kept from F101 and NR101 lead to single insulated portion of AC power cord (Blue and Brown wire). Dress AC power cord away from conductive parts. Attach Sheet Core, E to Ferrite Core and Frame Bottom. 4 Caution: 1. Ensure that AC power cord is not stressed whilst inserting it into AC cord bracket. – 20 – Insert the AC cord holder on to under cover 4mm 4mm 4mm KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 6 SERVICE ADJUSTMENTS 6-1. Accessing Diagnostic Menu 1. While TV set on standby, press the following sequence on the Remote commander (RMGA016). On screen display Channel 5 6-3. Control keys via Remote Commander. Buttons on the Remote Commander to access the service menu items and adjust the data values. POWER Volume (-) The following menu will appear on the screen MAIN_POWER_ERROR 0 5V_POWER_ERROR 0 AUDIO_ERROR 0 BALK_LIGHT_ERROR 0 TEMP_ERROR 0 Figure 1 2. To quit the diagnostic menu, turn off and on the set. 6-2. Viewing the Service Mode Display 6-4. Adjustment Method 1. While TV on standby mode, press the following sequence on the Remote commander. 6-4-1. Aging 1. On screen display Channel 5 Volume (+) While TV on standby mode, press the following sequence on the Remote commander. POWER (if wrong key is pressed or passed 3 seconds during each process, cancel entering the self-diagnosis display.) Item [Category/Item name] Within 17 characters [Data] Within 7 characters S E R V I C E T V 0 0 0 W B 0 0 0 W P R _ C W L O C T O P 4. M E P R O G R A M G T V : N V M : : 2 5 5 T M 0 . 0 M R 1 . 0 7 . 0 2 T 0 0 D 0 . 1 Channel 5 Volume (+) POWER Select AGING with 2 or 5 On the Remote Commander. Select AGING MODE with 1 or 4 On the Remote Commander. Select data value with 3 or 6 On the Remote Commander to 1 to enable. Refer to Service Items (Table 1) page 23. Press <I/1> to exit. When exit it will have the new data value and start aging. Aging condition: a) Supply voltage : Rating b) Time: More than 20 minutes c) Ambient Temp: 22-28 degrees d) Input : Set no signal except digital and analog RF(Video/Component/PC) 2. 3. Example on screen display: Categry On screen display 5. 6. 7. PROGRAM: Show the Application version GTV: Show the GTV Library version NVM: Show the NVM version in the NVM data (4bytes ASCII data) Example on screen display: 2. 3. To reset, press 8 – 0 – . To Exit, press the <I/1> key . S T V 0 0 0 A G I N G 0 0 0 A G I N G L O T O P C M O D E R E R V I 1 P R O G T M 0 . 0 7 0 G T V : A M : M R 1 . 0 . 2 N V M : T D 0 . 1 0 0 PROGRAM: Show the Application version GTV: Show the GTV Library version NVM: Show the NVM version in the NVM data (4bytes ASCII data) – 21 – C E KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 6-4-2. Resetting the User Menu- Factory Reset 6-4-3. White Balance Adjustment 1. Test Pattern: a) Connect video signal of white to video input b) Restort to original value : Color temp=0, Picture=Max,Brightness=50,Backlight=max While TV on standby mode, press the following sequence on the Remote commander. 1. On screen display Channel 5 Volume (+) POWER Select SERVICE with 2 or 5 On the Remote Commander. Select AUTO SET FACTORY with 1 or 4 On the Remote Commander. Select data value with 3 or 6 On the Remote Commander to 0 to current condition. Refer to Service Items (Table 1) page 23 Press <I/1> to exit. 2. 3. 4. 5. V 0 0 0 S 0 0 0 A L O S C T E U O R V I C E T O G S E P T On screen display F R A A C M T : O R Y E R V I 0 C E Channel 5 Volume (+) POWER Select WB with 2 or 5 On the Remote Commander. Select WPR_C with 1 or 4 On the Remote Commander. Select data value with 3 or 6 On the Remote Commander. Press <I/1> to exit. 2. 3. 4. 5. Example on screen display: T While TV on standby mode, press the following sequence on the Remote commander. Note: Refer to Service Items (Table 1) page 23 for other item and data value. Example on screen display: P R O G T M 0 . 0 7 0 G T V : M R 1 . 0 . 2 T V N V M : T D 0 . 1 0 0 0 0 0 W B 0 0 0 W P R L O T O P PROGRAM: Show the Application version GTV: Show the GTV Library version NVM: Show the NVM version in the NVM data (4bytes ASCII data) C _ C R A M : S E R 2 5 5 P R O G T M 0 . 0 7 0 G T V : M R 1 . 0 . 2 N V M : T D 0 . 1 0 0 V I PROGRAM: Show the Application version GTV: Show the GTV Library version NVM: Show the NVM version in the NVM data (4bytes ASCII data) – 22 – C E KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 6-5. Table 1 Category Item WPR C Description Remarks W/B R adjustment for Cool bit Min Max Initial 8 0 255 ADJ value Change color temperature to Cool WB SERVICE PRODUCTION W PG C W/B G adjustment for Cool 8 0 255 ADJ value WPB C W/B B adjustment for Cool 8 0 255 ADJ value W PR N W/B R adjustment for Cool 8 0 255 ADJ value 8 0 255 ADJ value 8 0 255 ADJ value 8 0 255 ADJ value 8 0 255 ADJ value 8 0 255 ADJ value 8 0 255 ADJ value W PG N W/B G adjustment for Cool WPB N W/B B adjustment for Cool WPR W1 W/B R adjustment for Warm1 W PG W 1 W/B G adjustment for Warm1 WPB W1 W/B B adjustment for Warm1 WPR W2 W/B R adjustment for Warm2 Change color temperature to Neautral Change color temperature to Warm1 Change color temperature to Warm2 WPG W2 W/B G adjustment for Warm2 8 0 255 ADJ value W PB W 2 W/B B adjustment for Warm2 8 0 255 ADJ value TUNING SYSTEM "TV" system FIX. "Auto" or "BG" or "DK" or "I" or "M" 3 0 0x08 0 "0:Auto, 1:BG, 2:DK, 3:I, 4:M, 5_:No use" NO SIGNAL MUTE When RF is no signal, select ON/OFF of audio mute. 1 0 1 0 0:OFF, 1:ON 0:current condition 1:SOEM(NORTH) 2:SOEM(SOUTH) 3:STT 4:SSV 5-:No use AUTOSET FACTORY Select a factory, and preset factory signal. Refer to the followings and sheet "AUTOSET FACTORY" 3 0 0x08 0 AGC Control of AGCOUT(66pin) of SMIC This value is adjust by production. Initial value is adjustment value. AGC Take Over 8 0 0xFF ADJ value Forced 2D Select "2D" and "Current" 0 OVMADAPT FM over-moduration adaptation Initial data is BG/DK/I : 1 M : 0 Radio :1 FILTBW Sound carrier filter bandwith. Initial data is BG/DK/I : 1 M : 0 Radio :1 1 0 0x01 1 0 0x01 current 0:Disable condition 1:Enable 2 0 0x03 0:Narrow current 1:Extra wide condition 2:Medium 3:Wide ADC AD auto calibration AD Cal. 1 0 0x01 0 SER1 Serial Number 1 SONY VERSION NO CHAR1 INDEX 8 0 0xFF ADJ value SER2 Serial Number 2 SONY VERSION NO CHAR2 INDEX 8 0 0xFF ADJ value SER3 Serial Number 3 SONY VERSION NO CHAR3 INDEX 8 0 0xFF ADJ value SER4 Serial Number 4 SONY VERSION NO CHAR4 INDEX 8 0 0xFF ADJ value SER5 Serial Number 5 SONY VERSION NO CHAR5 INDEX 8 0 0xFF ADJ value SER6 Serial Number 6 SONY VERSION NO CHAR6 INDEX 8 0 0xFF ADJ value SER7 Serial Number 7 SONY VERSION NO CHAR7 INDEX 8 0 0xFF ADJ value SER8 Serial Number 8 SONY VERSION NO CHAR8 INDEX 8 0 0xFF ADJ value AGING MODE Aging mode APRV_AGING_ENABLE_INDEX 1 0 1 0 AGING TIME Aging expire time APRV AGING TIME INDEX 8 0 0xFF 0 AGING AGING COLOR Aging color APRV_AGING_COLOUR_INDEX 8 0 0xFF 0 TEMP Read resister "TEMPERATURE" Same as NXP service mode 8 0 0xFF current condition SIG_BOOSTER_LEV Read A/D port for RF signal level A/D port: SARIN1 8 0 0xFF current condition STATUS 6-6. Board & Panel Replacement When replacing the BT board and Panel readjust the W/B. – 23 – 0:Current, 1:2D 1:Start auto ADC 0:Disable 1:Enable 0:Black 1:White 2:Red 3:Green 4:Blue – 24 – HDMI2_D2- HDMI2_D2+ HDMI2_D1- HDMI2_D1+ HDMI2_D0- HDMI2_D0+ HDMI2_CLK- HDMI2_CLK+ HDMI1_D2- HDMI1_D2+ HDMI1_D1- HDMI1_D1+ HDMI1_D0- HDMI1_D0+ HDMI1_CLK- HDMI1_CLK+ Q1005 Q1001 Q1000 Q1002 Q1003 5 IC1000 7 6 5 7 +5V_SW * Q1201 * IC1200 64 63 14 15 11 12 8 9 5 6 +3V3_STB +5V_SW +3V3_STB 21 39 64 22 38 63 5 26 25 29 76 77 73 28 32 74 70 35 34 31 IC1201 71 67 68 6 IC1202 Q1203 +3V3_STB 7 6 Q1006 HP_R HP_L 7 HP_DET HPD_DET2 HDMI_SEL1 HDMI_SEL2 HDMI_SDA HDMI_SCL HDMI_D2- HDMI_D2+ HDMI_D1- HDMI_D1+ HDMI_D0- HDMI_D0+ HDMI_CLK- HDMI_CLK+ HPD_DET1 PC_R PC_G PC_B PC_H PC_V VGA_L VGA_R MONIOUT_MUTE MONITOR_OUTL MONITOR_OUTR MOMITOR_CVBSOUT A_V2_IN_V A_V2_L A_V2_R A_V1_IN_V A_V1_L A_V1_R PB PR YUV_L YUV_R Y AUDIO_MUTE 4 2 6 3 IC2012 1 AGC SIG_BOOSTER I2C_SDA I2C_SCL SAW_SW SP_PROT LS_R LS_L HP_DET SP_MUTE Q8003 * Q8002 TV- TUNER MONIOUT_MUTE 1 5 4 * TU8000/ TU8001 7 11 +9V_TUNER +9V_TUNER Q2004 Q2009 Q2010 Q2007 Q2008 Q2012 * Q8000 * Q8001 Q2003 Q2002 33 32 23 22 20 * Q8010 * Q8004 25 16 17 10 11 21 * Q8005 * SWF801 * SWF800 IC2012 MAIN_VCC FM MIXER Q2012 OFF- MUTE * CF8001 * Q8007 FM_SIF FM_CLKP * Q8008 FM_RADIO _SW SIFP SIFN VIFP A BT2_BOARD (1/3) VIFN CN2000 4 R+ CN2000 3 RCN2000 1 L+ CN2000 2 L- KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 7 DIAGRAMS 7-1. BLOCK DIAGRAM 7-1-1. BT2 Board 4 – 25 – * CN3007 WAKE UP INT * CN3007 SCL * CN3007 SDA To Clock To HT1 * CN3001 REMOTE * CN3001 STANDBY * CN3001 ON OFF * CN3001 KEYBOARD * CN3001 ON TIMER To R2 * CN3003 RXD * CN3003 TXD * CN3003 SIRCS CN3002 RESETN CN3002 MD2 CN3002 MD0 CN3002 MD1 CN3002 NC CN3002 B INT CN3002 TXD CN3002 RXD IC3004 4 Q3002 1,2,3 IC3006 K1 A BT2_BOARD (1/3) 9 8 6 4 2 1 2 5 10 6 3 Q3002 NVM_WP SP_PROT 5V_DET HDMI_SEL2 HDMI_SEL1 AUDIO_MUTE POWER_ON_LED_A P_ON1_A ON_TIMER SIG_BOOSTER DC_DET FM_SIF TUN_SIF IC3002 IC3005 334_SCL BUS_SEL 334_SDA HDMI_D2- HDMI_D2+ HDMI_D1- HDMI_D1+ HDMI_D0- HDMI_D0+ HDMI_CLK- HDMI_CLK+ FM_CLKP HDMI_SCL HDMI_SDA HDMI_HPD2 HPD_DET1 LS_L TUN_R TUN_L BL_ON_OFFN LS_R MOMITOR_MUTE INV_ERR PLL_SW MAIN_L EDID_WP HPD_DET2 FM_RADIO_SW FM_CLKP MAIN_R MAIN_CVBS_Y SMIC_CLKP PR SMIC_CLKN DCDC_ON_OFF HPD_DET1 Y TIMER_LED PB 5 AA1 HP_DET HDMI_RXTERM PC_R PC_G 11 1 Y10 AA1 Y12 Y9 AA1 AB12 J3 C1 M4 J3 U2 PWR_DET PC_B P_ON2_A BL_ADJ STANDBY_LED_A PC_H PC_V 12 C1 B14 3 A14 AA9 * FB3027 * FB3026 A19 AA1 2 3 4 MAIN_VCC +5V_SW C1 1 5 B18 AB 9 B19 M3 6 5 AB1 4 6 Y1 B13 U1 W1 AA Y2 N2 N1 K2 C1 E20 E19 2 4 2 3 3 2 15 12 D2 E2 A18 7 D1 B22 F1 IC3001 Q3000 6 8 4 B2 C2 C1 C1 A17 9 11 IC4503 A1 B16 7 Hardware Reset A2 A3 A16 5 * IC3000 C1 2 BT2 BOARD 003 To ECS 3 CN3005 JTRSTN CN3005 JTDI CN3005 JTDO CN3005 JTMS CN3005 JCLK CN3005 RESETN To JTAG A20 A7 B7 A8 B8 A9 B9 A10 B10 AA AB AB AB AA AB AA AA AB A13 B13 A20 AA AB AB AB AA AB AA AA AB A13 B13 * IC3000 C2 P21 P22 R20 AB2 AA2 AB2 AB1 AB1 Y18,AB17 AA17,Y17 AB16,AA1 6 Y16,AB15 AA15,Y15 T22,T21 T20,U22 U21,U20 V22,V21 V20,W22 W21,W20 Y22,Y21 Y20,AA2 Y10 G2 G2 F21 F22 E21 E22 D21 D22 C2 SDCLKP SDCLKN CKE WEN RASN CASN BA1 BA0 MA[0- 11] MD[0:16] B_INT +3V3_STB FL3000 FL3002 FL3006 FL3005 FL3007 FL3011 FL3012 I G IC3003 O D13 W15 W6 Y6 D14 D16 M19 F20,G19 H20,J19 K20,L19 Y7 W8 W10 W12 J2,N4 P4,R4 V3,B4 C3,D 4 E3,F4 H4,K4 * IC3000 P19,N20 N22,W1 8 J8,L8 N8,R8 H9,R10 H11,R12 H13,R14 H15,K15 M15,P1 5 A11 W17 C6 D12 C1 C10,D9 C8,D7 B6 D1 B +1V8_STB +3V3_STB_SPV * CN3000 1 * CN3000 3 * CN3000 5 * CN3000 7 * CN3000 9 * CN3000 11 * CN3000 13 * CN3000 15 * CN3000 17 * CN3000 19 * CN3007 2 BT2_BOARD (3/3) FL3008 FL3009 FL3014 FL3015 FL3016 FL3001 FL3004 FL3003 B- INT RXO3+ RXO3- RXOC+ RXOC- RXO2+ RXO2- RXO1+ RXO1- RXO0+ RXO0- B- INT RX03+ RXO3- RX02+ RXO2- RXO1- RXO0- To LVDS KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W B BT2_BOARD (2/3) Q8501 +3V3_STB – 26 – VIFN VIFP SAW_SW AGC IF_PLL I IC8500 SIFN Q8501 G SIFP IC4000 68 67 71 72 79 66 58 33 32 53 29 O 64 63 52 51 48 45 19 18 41 40 39 14 13 50 46 44 16 10 9 7 5 4 2 1 RAM_VCC 49 44 23 22 21 YUV_L YUV_R VGA_L VGA_R A_V1_L A_V1_R A_V2_L A_V2_R MONITOR_OUTL MONITOR_OUTR MONITOR_CVBSOUT I2C_SDA I2C_SCL A_V2_IN_V A_V1_IN_V Y MAIN_CVBS_Y MAIN_R MAIN_L TUN_SIF Q8503 Q8502 Q8501 Q8501 SMIC_CLKP SMIC_CLKN IC4002 28.,29,30,31,32,33,3 5, 16,20, 51,47 45,4 6 26,2 7 2,4,5,7,8,10,11,13,5 4, BT2 BOARD 003 TUN_R TUN_L MD[0- 15] BA0,BA1 SDCLKN,SDCLKP CKE RASN CASN WEN DQSH,DQMH,DQSL,DQML MA[0- 11] VREF PWR_DET DCDC_ON_OFF P_ON2 +9V_TUNER DC_DET +3V3_STB_PLL PWR_DET P_ON1 IC4500 Hardware Reset MD0 MD2 RESETN 2 4 STANDBY MAIN_DONE BUS_SEL USB_INT ECS_TX ECS_RX Q7010 Q7004 RST_MICRO 1 2 5 2 90 89 87 63 62 93 50 24 12 11 1 5 2 STB_MAIN_VCC IC7002 IC7001 IC7003 IC4501 USB_HVP USB_HVM P_ON1_B IC7006 STB_MAIN_VCC 4 IC7004 Q4503 STANDBY_LED_B P_ON2_B POWER_ON_LED_B MAIN_SUB_SW MONITOR_SW MONITOR_SDA MONITOR_SCL UART_SW 334_TX 334_RX USB_POWER 3V3_STB 4 5 1 1 31 78 77 55 52 54 53 51 94 28 27 95 19 18 Q4502 3 16 FL7001 Q7004 FL7000 5 IC7000 5V TO 30V TUVIF TUVI F7004 5 1 Q4505 10 6 13 1 8 6 9 10 14 1 2 3 12 2 4 11 9 5 7 14 12 5 4 11 Q7008 1 1 2 * F7002 Q7005 3 1 IC4502 IC4505 IC7005 UART_RX POWER_ON_LED 15 3 Q7006 Q7007 F7005 F7004 P_ON1_A P_ON1 STANDBY_LED_A STANDBY_LED P_ON2_A P_ON2 POWER_ON_LED_A AUDIO VCC LOC_SCL LOC_SDA UART_TX +3V3_STB +1V8_STB +33V_SW_TUNER CN4500 CN7000 CN7000 CN7000 CN7000 CN7000 CN7000 CN7000 CN4500 CN4500 2 9 8 2 1 7 6 5 1 3 HVM MAIN VCC MAIN VCC AUDIO VCC AUDIO VCC STB Y VCC AC_OFF_DE T P_ON1 VCC HVP KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W CN6102 AC_L 3 F6102 GT3 BOARD FL6103 FL6102 7-1-2. GT3 Board (except 37S550A) D6101 – 27 – D6143 D6103 PH6106 Q6102 Q6103 D6106 D6145 D6109 D6138 IC6101 Q6105, Q6106 Q6108 IC6103 D6122 D6105,D6108 D6115 Q6107 Q6110 Q6109 Q6104 Q6111 Q6112 T6101 T6202 IC6104 D6129 D6122 PH6104 RM-GA016 RM-GA016W RM-GA016 RM-GA016W IC6105 KLV-32S530A, 26, 32, 37 S550A KLV-32S530A, 26, 32, 37 S550A – 28 – PH6104 T6201 PH6103 PH6102 T6102 IC6202 Q6201 IC6201 D6201 D6206 Q6202, Q6203 REG24V REG24V REG24V REG24V 1 REG12V 2 REG12V 3 REG12V 1 2 3 4 CN6202 12 AC_ON/OFF 9 AU_VCC 10 AU_VCC CN6202 CN6202 CN6201 CN6202 13 POWER_ON CN6202 11 STBY5.8V KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 7-1-3. HT1 Board HT 1 BO ARD IC 1000 C N1000 2 3 Q 1000 C N1000 5 TO BT BO ARD C N1000 7 Q 1001 C N1000 4 Q 1002 C N1000 6 Q 1003 D1001 D1004 – 29 – +3V 3_S W KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 7-2. CONNECTOR DIAGRAM 7-2-1 KLV-26S550A T-CON CNF1(30) LVDS CN2000(4) Hotel CN3003(6) CN7001(4) CN6202(13 ) CN6201(8) CN1(14) INVERTER 24V, Inv Err, BL, Dimmer CN3001(10) Power, Standby, Audio VCC, Main VCC CN7000(11) Speaker L, R CN3000(40) CN(3) ECS GT3 CN3002(18) BT2 SW CN6102(3) Switch CN8002(1) AC Power Remote, LED CN2801(6) HT1 Speaker L Speaker R – 30 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 7-2-2 KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T T-CON CNF1(30) LVDS CN2000(4) CN7000(11) CN3003(6 ) CN3000(40) CN1(14) CN3001(10) CN6202(13 ) 24V, Inv Err, BL, Dimmer CN6201(8) Hotel CN7001(4) Power, Standby, Audio VCC, Main VCC INVERTER Speaker L, R ECS CN(3) CN3002(18) BT2 GT3 SW CN6102(3) CN8002(1) Switch AC Power Remote, LED CN2801(6) HT1 Speaker L Speaker R 7-2-3 KLV-37S550A T-CON CNF1(30) LVDS CN3003(6) CN3001(10) CN2000(4) CN3000(40) CN1(14) CN3(13) CN2(10) 24V, Inv Err, BL, Dimmer INVERTER Hotel CN7001(4) Power, Standby, Audio VCC, Main VCC CN7000(11) Speaker L, R ECS CN(3) CN3002(18) BT2 G4T SW CN6102(3) Switch CN8002(1) AC Power Remote, LED CN2801(6) HT1 Speaker L Speaker R – 31 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 7-3. CIRCUIT BOARD LOCATION 7-3-1 KLV-26S550A GT3 Board BT2 Board HT1 Board 7-3-2 KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T GT3 Board BT2 Board HT1 Board – 32 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 7-3-3 KLV-37S550A PS Unit (G4T) Board BT2 Board HT1 Board – 33 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 7-4. SCHEMATIC DIAGRAM Board Function 7-5. PRINTED WIRING BOARDS Note BT2 I/O, AV INPUT/OUTPUT, HDMI, Due to complexity of the board, performing PC,I, HP/AUDIO/LOC TOP/DDR/ component level field repairs are not POWER DC/ TUNER.FM.IF/ recommended. Complete board AV SWITCH.SMIC replacement is required if service is G4T(37S550A) Power Supply necessary. GT3(26S550A, For part number information, refer to 32S530A, Exploded View or Electrical Parts List 32S550A, section in this manual. 32S550A/L, 32S550A/T) HT1 Key / LED / SIRCS 7-6. SEMICONDUCTOR Due to complexity of the board, performing component level field repairs are not recommended. Complete board replacement is required if service is necessary. – 34 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 8 EXPLODED VIEWS • • Components not identified by a part number or description are not stocked because they are not required for routine service. The component parts of an assembly are indicated by the reference numbers in the far right column of the part list and within the dotted lines of the diagram. a b c d e f g h i NOTE: The components identified by shading and ! mark are critical for safety. Replace only with part number specified. Note: The components identified by mark contain confidential information. Strictly follow the instructions whenever the components are repaired and /or replaced. 2-580-591-01 2-580-600-01 2-580-602-01 2-580-608-01 2-580-626-01 2-580-629-01 2-580-639-01 2-580-640-01 7-685-648-79 • Item marked with an asterisk (*) are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these components. SCREW, +PSW M3X5 SCREW, +PSW M4X8 SCREW, +PSW M4X12 (37S550A) SCREW, +PSW M5X16 SCREW, SP 4-4O UNC SCREW, +BVST 3X8 SCREW, +BVTP2 4X12 SCREW, +BVTP2 4X16 SCREW +BVTP 3X12 TYPE2 IT-3 Note: The illustrations provided in this section might have slight difference from actual set. 8-1. KLV-26S550A 8-1-1. REAR CABINET AND STAND ASSY a h i h h 2 b / 3 4 e 6 1 h 5 d REF. NO. PART NO. – 35 – 1 2 3 4 5 X-2345-184-1 * 3-106-086-01 * 4-115-101-01 * 4-127-924-01 X-2345-158-1 6 4-138-855-01 DESCRIPTION REAR COVER (26) ASSY COVER, ECS COVER, ECS COVER, ECS(S) STAND ASSY (M1) COVER, MS/USB REMARK KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 8-1-2. BOARDS, SPEAKERS, BEZEL AND PANEL 51 52 i 58 h 54 53 56 60 b h 53 h h 57 h 59 55 f REF. NO. PART NO. DESCRIPTION REMARK 51 X-2345-183-1 52 ! 1-802-866-12 53 1-858-210-11 54 X-2345-363-1 55 X-2345-364-1 BEZEL (26) ASSY LCD PANEL (26 INCH WXGA TFT) LOUDSPEAKER (4.2X10CM) BAFFLE, SP (26L) ASSY BAFFLE, SP (26R) ASSY 56 57 58 59 BRACKET, SIDE JACK (EX2T) COVER, UNDER (26/32) HT1 MOUNT GT3 COMPLETE (EXCEPT 26S550A RUSSIA) GT3(26) COMPLETE (26S550A RUSSIA) BT2 MOUNT (SERVICE) (26S550A RUSSIA) BT2 MOUNT (SERVICE) (EXCEPT 26S550A RUSSIA) 60 4-125-782-01 4-125-785-01 * A-1663-488-A * A-1665-115-A A-1704-566-A A-1708-543-A A-1665-501-A – 36 – b f KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 8-2.KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T 8-2-1. REAR CABINET AND STAND ASSY a h i h h 2 b e d 1 2 3 4 5 X-2345-139-1 * 3-106-086-01 * 4-115-101-01 * 4-127-924-01 X-2345-158-1 6 4-138-855-01 * 3-292-896-01 6 1 5 DESCRIPTION 3 4 h REF. NO. PART NO. / REMARK REAR COVER (32) ASSY COVER, ECS COVER, ECS COVER, ECS(S) STAND ASSY (M1) COVER, MS/USB (32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) COVER, MS/USB (EXCEPT 32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) – 37 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 8-2-2. BOARDS, SPEAKERS, BEZEL AND PANEL 51 h 60 56 52 58 i h f 53 b 54 b b 59 b h b h 53 b f b 55 REF. NO. PART NO. 51 X-2345-137-1 X-2345-370-1 X-2348-561-1 X-2348-562-1 52 ! 1-802-807-11 53 1-826-873-11 1-858-209-11 54 55 X-2345-361-1 X-2345-362-1 56 57 58 59 4-125-782-01 4-125-785-01 * A-1663-488-A * A-1663-495-A A-1704-563-A 60 A-1665-502-A A-1707-902-A A-1663-500-A DESCRIPTION b 57 REMARK BEZEL(32) ASSY (32S550A) BEZEL(32) ASSY (32S530A) BEZEL(32)(L) ASSY (32S550A/L) BEZEL(32)(T) ASSY (32S550A/T) LCD PANEL (31.5 INCH WXGA TFT) LOUDSPEAKER (3.4X17.5CM) (32S550A (IRAN, NEW ZEALAND), 32S550A/L RUSSIA, 32S550A/T RUSSIA) LOUDSPEAKER (3.4X17.5CM) (EXCEPT 32S550A (IRAN, NEW ZEALAND), 32S550A/L RUSSIA, 32S550A/T RUSSIA) BAFFLE, SP (32/37L) ASSY BAFFLE, SP (32/37R) ASSY BRACKET, SIDE JACK (EX2T) COVER, UNDER (26/32) HT1 MOUNT GT3 COMPLETE (EXCEPT 32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) GT3(32) COMPLETE (32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) BT2 MOUNT (SERVICE) (32S530A (ME, THAILAND)) BT2 MOUNT (SERVICE) (32S550A (RUSSIA, TUNISIA), 32S550A/L RUSSIA, 32S550A/T RUSSIA) BT2 MOUNT (SERVICE) (EXCEPT 32S530A (ME, THAILAND), 32S550A (RUSSIA, TUNISIA), 32S550A/L RUSSIA, 32S550A/T RUSSIA) – 38 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 8-3. KLV-37S550A 8-3-1. REAR CABINET AND STAND ASSY a h c c h 2 h / 3 4 e 1 h 5 d REF. NO. PART NO. 1 2 3 4 5 X-2345-203-1 * 3-106-086-01 * 4-115-101-01 * 4-127-924-01 X-2345-159-1 6 4-138-855-01 DESCRIPTION 6 REMARK REAR COVER (37) ASSY COVER, ECS COVER, ECS COVER, ECS(S) STAND ASSY (ML1) COVER, MS/USB – 39 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 8-3-2. BOARDS, SPEAKERS, BEZEL AND PANEL 51 h 53 52 54 58 h h 60 i 57 h f b 53 h h 55 63 b 61 62 b h b 59 56 f REF. NO. PART NO. 51 X-2345-202-1 52 ! 1-802-864-11 53 1-826-873-11 1-858-209-11 54 55 X-2345-361-1 X-2345-362-1 56 57 58 59 60 4-125-786-01 4-125-782-01 * A-1663-488-A 1-474-161-11 A-1671-483-A 61 62 63 * 4-125-862-01 * 4-125-863-01 * 4-125-861-01 DESCRIPTION REMARK BEZEL(37) ASSY LCD PANEL (37 INCH WXGA TFT) LOUDSPEAKER (3.4X17.5CM) (37S550A (GE, NEW ZEALAND, SOUTH AFRICA)) LOUDSPEAKER (3.4X17.5CM) (EXCEPT 37S550A (GE, NEW ZEALAND, SOUTH AFRICA)) BAFFLE, SP (32/37L) ASSY BAFFLE, SP (32/37R) ASSY COVER, UNDER (37) BRACKET, SIDE JACK (EX2T) HT1 MOUNT PS UNIT(G4T) BT2 MOUNT (SERVICE) (EXCEPT 37S550A(RUSSIA, TUNISIA)) A-1707-902-A BT2 MOUNT (SERVICE) (37S550A (RUSSIA, TUNISIA)) FRAME, SPINE(37L) FRAME, SPINE(37R) FRAME, BOTTOM(37) – 40 – b KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 9 ELECTRICAL PARTS LIST NOTE: REF NO. PART NO. DESCRIPTION The components identified by mark contain confidential information. Strictly follow the instructions whenever the components are repaired and /or replaced. Due to complexity of the board, performing component level field repairs are not recommended. Complete board replacement is required if service is necessary. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. • Items marked " " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. REMARK REF NO. PART NO. 1-487-326-11 1-500-386-11 * A-1665-115-A GT3 COMPLETE (EXCEPT 26S550A RUSSIA) A-1704-566-A GT3(26) COMPLETE (26S550A RUSSIA) ******************* 4-022-115-00 ! 1-836-510-11 A-1708-543-A BT2 MOUNT (SERVICE) (26S550A RUSSIA) A-1665-501-A BT2 MOUNT (SERVICE) (EXCEPT 26S550A RUSSIA) ********************* 1-836-511-11 ! 1-836-512-11 *********************************************************************** 1-569-008-33 1-770-019-71 * 4-127-333-01 * 4-127-334-01 1-821-926-11 ADAPTOR, CONVERSION (26S550A PHILIPPINES) ADAPTOR, CONVERSION PLUG 3P (26S550A GE) CUSHION, UPPER CUSHION, LOWER PLUG CONVERSION ADAPTOR (26S550A SOUTH AFRICA) * 4-127-335-01 4-130-985-11 INDIVIDUAL CARTON MANUAL, INSTRUCTION (ENGLISH) (26S550A (GE, ME, SOUTH AFRICA)) MANUAL, INSTRUCTION (CHINESE) (26S550A GE, ME) MANUAL, INSTRUCTION (ARABIAN) (26S550A ME) MANUAL, INSTRUCTION (PERSIAN) (26S550A ME) 4-130-985-51 4-130-985-61 4-130-985-71 4-137-767-11 4-137-767-21 X-2190-783-1 1-487-316-11 1-487-316-31 9-885-123-43 9-885-131-73 SWITCH UNIT FILTER, CLAMP (FERRITE CORE) (26S550A RUSSIA) HOLDER, AC CORD POWERSUPPLYCORD(WITHCONNECTOR) (EXCEPT 26S550A (INDIA, THAILAND)) POWER SUPPLY CORD (26S550A THAILAND) POWER SUPPLY CORD (26S550A INDIA) REMOTE COMMANDER (RM-GA016) (DARK GRAY) REMOTE COMMANDER (RM-GA016) (DARK GRAY) REMOTE COMMANDER BATTERY COVER (DARK GRAY) REMOTE COMMANDER BATTERY COVER (DARK GRAY) *********************************************************************** 9-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T A-1665-502-A BT2 MOUNT (SERVICE) (32S530A (ME, THAILAND)) A-1707-902-A BT2 MOUNT (SERVICE) (32S550A (RUSSIA, TUNISIA), 32S550A/L RUSSIA, 32S550A/T RUSSIA) A-1663-500-A BT2 MOUNT (SERVICE) (EXCEPT 32S530A (ME, THAILAND), 32S550A (RUSSIA, TUNISIA), 32S550A/L RUSSIA, 32S550A/T RUSSIA) ********************** MANUAL, INSTRUCTION (RUSSIAN) (26S550A ME, RUSSIA) MANUAL, INSTRUCTION (FRENCH) (26S550A ME) MANUAL, INSTRUCTION (UKHRAINE) (26S550A RUSSIA) MANUAL, INSTRUCTION (ENGLISH) (26S550A (INDIA, PHILIPPINES, THAILAND)) MANUAL, INSTRUCTION (THAILAND) (26S550A (PHILIPPINES, THAILAND)) * A-1663-495-A GT3 COMPLETE (EXCEPT32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) * A-1704-563-A GT3 COMPLETE (32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) ************************************ * A-1663-488-A HT1 MOUNT *********** BAG ASSY, RUDDER LOCK (26S550A (INDIA, PHILIPPINES, THAILAND)) <CONNECTORS> 1-836-562-11 1-910-053-23 1-910-053-35 1-910-053-36 1-910-053-37 REMARK REMOTE COMMANDER ********************** *********************************************************************** * * * * DESCRIPTION *********************************************************************** ACCESORIES AND PACKING MATERIALS ************************************** 4-130-985-41 COILS • MMH : mH, UH : μH MISCELLANEOUS ***************** * A-1663-488-A HT1 MOUNT ************ 4-130-985-31 CAPACITORS • MF : μF, PF : μμF *********************************************************************** 9-1. KLV-26S550A 4-130-985-21 DESCRIPTION REMARK • All resistors are in ohms • F : nonflammable ************************************************************************ LEAD WIRE WITH CONNECTOR(LVDS) CONNECTOR ASSY 13P CONNECTOR ASSY 10P CONNECTOR ASSY 14P SP CONNECTOR ASSY 4P – 41 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. 4-146-351-11 ACCESORIES AND PACKING MATERIALS ************************************** X-2190-783-1 1-569-008-33 ADAPTOR, CONVERSION (32S550A PHILIPPINES, 32S550A/L PHILIPPINES, 32S550A/T PHILIPPINES) 1-770-019-71 ADAPTOR, CONVERSION PLUG 3P (32S550A GE, 32S550A/L GE, 32S550A/TGE) PLUG CONVERSION ADAPTOR (32S550A SOUTH AFRICA, 32S550A/L SOUTH AFRICA, 32S550A/T SOUTH AFRICA) BAG, POLYETHYLENE (32S550A (THAILAND, PHILIPPINES, INDIA), 32S550A/L PHILIPPINES, 32S550A/T PHILIPPINES) 1-821-926-11 2-669-511-11 * 4-127-336-01 * 4-140-607-01 * 4-127-337-01 * 4-140-608-01 * 4-127-338-01 * 4-136-041-01 * 4-137-768-01 * 4-140-524-01 * 4-146-350-01 4-130-985-11 4-130-985-21 4-130-985-31 4-130-985-41 4-130-985-51 4-130-985-61 4-130-985-71 4-137-767-11 4-137-767-21 CUSHION, UPPER (EXCEPT 32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) CUSHION UPPER (32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) CUSHION, LOWER (EXCEPT 32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) CUSHION LOWER (32S550A NEW ZEALAND, 32S550A/L RUSSIA, 32S550A/T RUSSIA) INDIVIDUAL CARTON (EXCEPT (32S530A, 32S550A(India, Philippines, Thailand)) DESCRIPTION REMARK MANUAL, INSTRUCTION (ENGLISH & PERSIAN) (32S550A(IRAN)) BAG ASSY, RUDDER LOCK (32S550A (INDIA, PHILIPPINES, THAILAND), 32S550A/L (PHILIPPINES), 32S550A/T (PHILIPPINES)) *********************************************************************** <CONNECTORS> * 1-910-053-22 * 1-910-053-23 * 1-910-053-24 1-836-565-11 1-836-564-11 1-836-564-11 * 1-910-053-25 CONNECTOR ASSY 10P CONNECTOR ASSY 13P CONNECTOR ASSY 14P LEAD WIRE WITH CONNECTOR(LVDS) (32S550A (NEW ZEALAND, RUSSIA, TUNISIA)) LEAD WIRE WITH CONNECTOR(LVDS) (EXCEPT 32S550A (NEW ZEALAND, RUSSIA, TUNISIA)) LEAD WIRE WITH CONNECTOR(LVDS) (32S530A) SP CONNECTOR ASSY 4P *********************************************************************** INDIVIDUAL CARTON (32S530A(ME)) INDIVIDUAL CARTON (32S550A(India, Philippines, Thailand)) INDIVIDUAL CARTON (32S530A(Thailand)) INDIVIDUAL CARTON (32S550A(Iran)) * 3-292-896-01 1-500-386-11 4-022-115-00 4-145-540-01 MANUAL, INSTRUCTION (ENGLISH) (32S530A(ME), 32S550A (GE, ME, NEW ZEALAND, SOUTH AFRICA, TUNISIA), 32S550A/L (SOUTH AFRICA, GE), 32S550A/T (GE, ME, SOUTH AFRICA)) 4-136-079-01 ! 1-836-510-11 MANUAL, INSTRUCTION (CHINESE) (32S550A (GE, ME, SOUTH AFRICA), 32S550A/L (GE, SOUTH AFRICA), 32S550A/T (GE, ME)) MANUAL, INSTRUCTION (ARABIAN) (32S530A(ME), 32S550A (ME, TUNISIA) , 32S550A/L SOUTH AFRICA, 32S550A/T ME) MANUAL, INSTRUCTION (PERSIAN) (32S530A(ME), 32S550A ME , 32S550A/L SOUTH AFRICA, 32S550A/T ME) MANUAL, INSTRUCTION (RUSSIAN) (32S530A(ME), 32S550A (ME, RUSSIA), 32S550A/L (RUSSIA, SOUTH AFRICA), 32S550A/T (ME, RUSSIA)) MANUAL, INSTRUCTION (FRENCH) (32S530A(ME), 32S550A ME, TUNISIA, 32S550A/L SOUTH AFRICA, 32S550A/T ME ) ! 1-836-511-11 ! 1-836-512-11 ! 1-836-513-11 1-487-326-11 4-103-642-11 MISCELLANEOUS ***************** COVER, MS/USB FILTER, CLAMP (FERRITE CORE) (32S550A (IRAN, NEW ZEALAND, TUNISIA, RUSSIA), 32S550A/L RUSSIA, 32S550A/T RUSSIA) HOLDER, AC CORD LABEL, POP(32S55-RUSS) (32S550A/L RUSSIA, 32S550A/T RUSSIA) LABEL, REAR TERMINAL(DERI) (32S530A) POWERSUPPLYCORD(WITHCONNECTOR) (EXCEPT 32S530A ( THAILAND), 32S550A(INDIA, NEW ZEALAND)) POWER SUPPLY CORD (32S530A THAILAND) POWER SUPPLY CORD (32S550A INDIA) POWER SUPPLY CORD (32S550A(NEW ZEALAND)) SWITCH UNIT EMBLEM, SONY NO8 (32S550A(IRAN)) *************************************************************************** REMOTE COMMANDER ********************** 1-487-316-11 MANUAL, INSTRUCTION (UKHRAINE) (32S550A RUSSIA, 32S550A/L RUSSIA, 32S550A/T RUSSIA) MANUAL, INSTRUCTION (ENGLISH) (32S530A(Thailand), 32S550A (INDIA, THAILAND, PHILIPPINES), 32S550A/L PHILIPPINES, 32S550A/T PHILIPPINES) MANUAL, INSTRUCTION (THAILAND) (32S530A(Thailand), 32S550A (PHILIPPINES, THAILAND), 32S550A/L PHILIPPINES, 32S550A/T PHILIPPINES) 1-487-316-31 9-885-123-43 9-885-131-73 REMOTE COMMANDER (RM-GA016) (DARK GRAY) REMOTE COMMANDER (RM-GA016) (DARK GRAY) REMOTE COMMANDER BATTERY COVER (DARK GRAY) REMOTE COMMANDER BATTERY COVER (DARK GRAY) *********************************************************************** – 42 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. 9-3. KLV-37S550A 4-137-767-21 4-146-351-11 A-1671-483-A BT2 MOUNT (SERVICE) (EXCEPT 37S550A (RUSSIA, TUNISIA)) A-1707-902-A BT2 MOUNT (SERVICE) (37S550A (RUSSIA, TUNISIA)) ********************** * 1-910-053-47 * 1-910-053-48 * 1-910-053-49 1-836-566-11 PS UNIT(G4T) ************* 1-836-567-11 ACCESORIES AND PACKING MATERIALS ************************************** 2-669-511-11 * 4-127-339-01 * 4-141-724-01 * 4-127-340-01 * 4-141-725-01 * 4-127-341-01 * 4-147-046-01 4-130-985-11 4-130-985-21 4-130-985-31 4-130-985-41 4-130-985-51 4-130-985-61 4-130-985-71 4-137-767-11 * 1-910-053-50 ADAPTOR, CONVERSION (37S550A PHILIPPINES) ADAPTOR, CONVERSION PLUG 3P (37S550A GE) PLUG CONVERSION ADAPTOR (37S550A SOUTH AFRICA) BAG, POLYETHYLENE (37S550A (INDIA, PHILLIPINES, TAIWAN)) CUSHION, UPPER (EXCEPT 37S550A (GE, NEW ZEALAND, SOUTH AFRICA)) CONNECTOR ASSY 10P CONNECTOR ASSY 13P CONNECTOR ASSY 14P LEAD WIRE WITH CONNECTOR(LVDS) (EXCEPT 37S550A NEW ZEALAND) LEAD WIRE WITH CONNECTOR(LVDS) (37S550A NEW ZEALAND) SP CONNECTOR ASSY 4P *********************************************************************** <MISCELLANEOUS> 1-500-386-11 4-022-115-00 4-143-818-11 CUSHION UPPER (37S550A IRAN, GE, NEW ZEALAND, SOUTH AFRICA)) CUSHION, LOWER (EXCEPT 37S550A (IRAN, GE, NEW ZEALAND, SOUTH AFRICA)) CUSHION LOWER (37S550A (IRAN, GE, NEW ZEALAND, SOUTH AFRICA)) INDIVIDUAL CARTON (EXCEPT 37S550A(IRAN)) INDIVIDUAL CARTON (37S550A IRAN) MANUAL, INSTRUCTION (ENGLISH) (37S550A (GE, ME, NEW ZEALAND, SOUTH AFRICA, TUNISIA)) MANUAL, INSTRUCTION (CHINESE) (37S550A (GE, ME)) MANUAL, INSTRUCTION (ARABIAN) (37S550A (ME, TUNISIA)) MANUAL, INSTRUCTION (PERSIAN) (37S550A ME) MANUAL, INSTRUCTION (RUSSIAN) (37S550A (ME, RUSSIA)) MANUAL, INSTRUCTION (THAILAND) (37S550A (PHILIPPINES, THAILAND)) MANUAL, INSTRUCTION (37S550A(IRAN)) <CONNECTORS> *********************************************************************** 1-569-008-33 1-770-019-71 1-821-926-11 REMARK *********************************************************************** * A-1663-488-A HT1 MOUNT *********** 1-474-161-11 DESCRIPTION 4-140-368-01 ! 1-836-510-11 ! 1-836-511-11 ! 1-836-512-11 ! 1-836-513-11 4-131-527-11 1-487-326-11 4-100-136-01 4-103-642-21 FILTER, CLAMP (FERRITE CORE) (37S550A (NEW ZEALAND, RUSSIA, TUNISIA)) HOLDER, AC CORD LABEL, ENERGY RATING(S) (37S550A NEW ZEALAND) LABEL, MRP (37S550A INDIA) POWERSUPPLYCORD(WITHCONNECTOR) (EXCEPT 37S550A (INDIA, NEW ZEALAND, THAILAND)) POWER SUPPLY CORD (37S550A THAILAND) POWER SUPPLY CORD (37S550A INDIA) POWER SUPPLY CORD (37S550A NEW ZEALAND) SPACER, G BOARD SWITCH UNIT SHEET(CORE), C (32S550A(IRAN)) EMBLEM, SONY NO. 8 (37S550A(IRAN)) *********************************************************************** REMOTE COMMANDER ********************** 1-487-316-11 1-487-316-31 9-885-123-43 MANUAL, INSTRUCTION (FRENCH) (37S550A (ME, TUNISIA)) MANUAL, INSTRUCTION (UKHRAINE) (37S550A RUSSIA) MANUAL, INSTRUCTION (ENGLISH) (37S550A (INDIA, PHILIPPINES, THAILAND)) 9-885-131-74 – 43 – REMOTE COMMANDER (RM-GA016) (DARK GRAY) REMOTE COMMANDER (RM-GA016) (DARK GRAY) REMOTE COMMANDER BATTERY COVER (DARK GRAY) REMOTE COMMANDER BATTERY COVER (DARK GRAY) SUPPLEMENT-1 MODEL COMMANDER KLV-26S550A KLV-32S530A EX2T CHASSIS DEST. RM-GA016 & GE, India, ME, RM-GA016W Philippines, Russia, South Africa, Thailand COMMANDER KLV-32S550A/L RM-GA016 & GE, ME, Philippines, (Blue) RM-GA016W Russia, South Africa KLV-32S550A/T RM-GA016 & ME, Thailand (Brown) RM-GA016W KLV-32S550A MODEL RM-GA016 & GE, India, Iran, ME, RM-GA016W New Zealand, Philippines, Russia, South Africa, Thailand Tunisia KLV-37S550A RM-GA016 & GE, ME, Philippines, RM-GA016W Russia, South Africa RM-GA016 & GE, India, Iran, ME, RM-GA016W Philippines, Russia, Thailand, Tunisia SUBJECT : Part Information Change: Addition of: 1. Removal of Rear Cover and Switch Unit Procedure 2. Triage Chart 3. Trouble Shooting This supplement applies only to the models listed above. Other information remains the same as in the original issue and previous supplements. Please refer: 1) Removal of Rear Cover and Switch Unit Procedure (Page 45) 2) Triage Chart (Page 46) 3) Trouble Shooting (Page 47~50) – 44 – DEST. KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 1 SAFETY NOTES 1-7. Removal of Rear Cover Procedure Note: For Screws informations, Please refer to Section 4 : Disassembly . Push point at Switch Unit. 2 1 3 3) Remove Rear Cover from Switch Unit while pushing at Switch Unit towards inner set. Photo show the position during rear cover opening: 1) Raise Point 1. 2) Press 'Push point' towards inner side of set. 1-8. Removal of Switch Unit Procedure 1 2 Push this position to remove Switch Unit more easily Push and slant towards inner side of set. Push and slant towards inner side of set to remove Switch Unit correctly. – 45 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 2 SELF DIAGNOSTIC FUNCTION 2-7. Triage Chart 2-7-1. KLV-26S550A, 32S530A, 32S550A, 32S550A/L, 32S550A/T Failure 2x 4x 6x 7x 8x No Power Sound NG Picture NG 4x 6x 7x 8x No Power Sound NG Picture NG BT2 GT3 Panel Speaker 2-7-2. KLV-37S550A Failure 2x BT2 G4 Panel Speaker – 46 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 3 TROUBLE SHOOTING 3-1. Flowchart 3-1-1. NO POWER NO POWER No Power YES Check AC cable connection NO AC cable NG YES STBY_VCC(GT3:6.2V, G4T:5.6V) CN7000_7pin on BT2 Board NO GT3, G4T Board NG YES BT2 or Switch Unit NG 3-1-2. SOUND NG SOUND NG Sound NG Only speaker out? NO BT2 Board NG YES AUDIO_VCC(GT3:13V, G4T:15V) CN7000_1, 2pin on BT2 Board NO GT3, G4T Board NG YES UI of Audio setting correct? Volume,TV speaker YES NO Set correctly or reset by menu – 47 – BT2 Board or Speaker NG KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 3-1-3. PICTURE NG PICTURE NG PICTURE NG All input have problem NO BT2 Board NG YES Backlight on? NO BT2 Board GT3, G4T Board NG YES UI of some picture setting correct? YES NO Set correctly or reset by menu – 48 – LVDS harness connection or BT2 board or Panel NG KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 3-2. Board Replacement Order 3-2-1. LED 2x or 4x BLINKING LED 2x or 4 x BLINKING Replace(OK) GT3 or G4T NO Finish Replace BT2 3-2-2. LED 8x BLINKING LED 8x BLINKING Replace(OK) Speaker NO Replace BT2 – 49 – Finish KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W 3-2-3. LED 6x BLINKING LED 6x BLINKING Replace(OK) GT3 or G4T NO Replace(OK) BT2 NO Replace Panel Module Finish 3-2-4. LED 7x BLINKING LED 8x BLINKING BT2 Replace(OK) NO Replace Panel Module – 50 – Finish KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SUPPLEMENT-2 MODEL COMMANDER KLV-26S550A EX2T CHASSIS DEST. MODEL COMMANDER RM-GA016 & GE, India, Sogul, Iran, RM-GA016W Saudi Arabia, Singapore, ARM, Indonesia, Philippines, Russia, South Africa, Thailand Vietnam. SUBJECT : Part Information Change: Addition of: i) Stand Assy ii) Fall lock belt bag assy This supplement shows only variant information for the new model(s). Other information remains the same as in the original issue. Please refer: 1) Stand Assy (Page 52) 2) Fall lock belt bag assy (Page 53) – 51 – DEST. KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 8 EXPLODED VIEWS 8-1. KLV-26S550A 8-1-1. REAR CABINET AND STAND ASSY 5 REF. NO. PART NO. 5 DESCRIPTION REMARK X-2349-157-1 STAND ASSY (M1) (26S550A (INDIA, PHILIPINES, THAILAND, VIETNAM)) – 52 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 RM-GA016W SECTION 9 ELECTRICAL PARTS LIST REF NO. PART NO. DESCRIPTION REMARK X-2348-140-2 BAG ASSY, FALL LOCK BELT (26S550A) – 53 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 SUPPLEMENT-3 MODEL KLV-32S530A KLV-32S550A EX2T CHASSIS COMMANDER DEST. MODEL COMMANDER DEST. RM-GA016 SOGUL, Thailand KLV-32S550A/L RM-GA016 Hong Kong, Malaysia, SOGUL, Iran, Saudi Arabia, Singapore, ARM, Indonesia, Phillipines, Vietnam South Africa (Blue) RM-GA016 Hong Kong, Malaysia, India, Iran, SOGUL, Saudi Arabia, Singapore, ARM, Indonesia, New Zealand, Phillipines, Vietnam, Russia, South Africa, Tunisia KLV-32S550A/T RM-GA016 Hong Kong, Malaysia, SOGUL, Iran, Saudi Arabia, Singapore, ARM, Indonesia, Phillipines, Russia, Thailand, Vietnam (Brown) SUBJECT : Part Information Changed - LCD Panel Part Number This supplement applies only to the models listed above. Other information remains the same as in the original issue and previous supplements. Please refer: 1) Exploded View (Page 55) 2) Electrical Part List (Page 56) Note: LCD Panel Part Number changed from CMO to SLCD. Related to this matter, some connectors are changed accordingly. Please refer to page mentioned above for details informations. – 54 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 8-2-2. BOARDS, SPEAKERS, BEZEL AND PANEL (refer page 38) 52 REF. NO. PART NO. 52 ! 1-802-932-11 ! 1-802-932-32 DESCRIPTION REMARK LCD PANEL (32 INCH WXGA TFT) LCD PANEL (32 INCH WXGA TFT) – 55 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 SECTION 9 ELECTRICAL PARTS LIST REF NO. PART NO. DESCRIPTION REMARK 9-2. KLV-32S530A, 32S550A, 32S550A/L, 32S550A/T (REFER PAGE 42) 1-836-846-11 1-836-846-21 1-836-847-11 1-836-847-21 1-910-053-52 LEAD WIRE WITH CONNECTOR(LVDS) (except 32S550A (NEW ZEALAND, RUSSIA, TUNISIA)) LEAD WIRE WITH CONNECTOR(LVDS) (except 32S550A (NEW ZEALAND, RUSSIA, TUNISIA)) LEAD WIRE WITH CONNECTOR(LVDS) (32S550A (NEW ZEALAND, RUSSIA, TUNISIA)) LEAD WIRE WITH CONNECTOR(LVDS) (32S550A (NEW ZEALAND, RUSSIA, TUNISIA)) CONNECTOR ASSY 14P – 56 – KLV-32S530A, 26, 32, 37 S550A RM-GA016 SUPPLEMENT-4 MODEL KLV-26S550A/1 KLV-26S550A/3 KLV-32S550A/1 KLV-32S550A/3 KLV-37S550A/1 KLV-37S550A/3 COMMANDER DEST. RM-GA016 SOGUL RM-GA016 SOGUL RM-GA016 SOGUL RM-GA016 SOGUL RM-GA016 SOGUL RM-GA016 SOGUL EX2T CHASSIS MODEL COMMANDER SUBJECT : New Model Addition This supplement shows only variant information for the new model(s). Other information remains the same as in the original issue. SECTION 4: DISASSEMBLY 4-1. KLV-26S550A/1, 26S550A/3 4-1-1. R2 Board and Rear Cover Removal (Refer Page 8) 1 Remove R Bracket (Top) 2 Disconnect CN001 6 Two screws (+PSW M3 X 5) 7 Two screws (+BVTP 3 X 12) 5 Twelve screws (BVTP2 4 X 16) 8 Two screw (+PSW M4 X 8) 9 Lift to remove Rear Cover – 57 – 3 Two screws (+BVTP 3 X 14) 4 R2 Board DEST. KLV-26, 32, 37 S550A RM-GA016 4-2. KLV-32S550A/1, 32S550A/3 4-2-1. R2 and Rear Cover Removal (refer page 9) 1 Remove R Bracket (Top) 2 Disconnect CN001 3 Two screws (+BVTP 3 X 14) 4 R2 Board 6 Two screw (+PSW M3 X 5) 7 Three screws (+BVTP 3 X 12) 5 Twelve screws (BVTP2 4 X 16) 8 Two screw (+PSW M4 X 8) 9 Lift to remove Rear Cover 4-3. KLV-37S550A/1, 37S550A/3 4-3-1. R2 and Rear Cover Removal (refer page 10) 1 Remove R Bracket (Top) 2 Disconnect CN001 7 Two screws (+PSW M3 X 5) 8 Four screws (+PSW 4 X 16) 6 Two screws (+BVTP 3 X 12) 5 Twelve screws (BVTP2 4 X 16) 9 Lift to remove Rear Cover – 58 – 3 Two screws (+BVTP 3 X 14) 4 R2 Board KLV-26, 32, 37 S550A RM-GA016 SECTION 5 SERVICE ADJUSTMENT (refer page 21) Preset "Test" button on remote commander 1. 5 + The following menu appears on the screen. Function Settings Press the following buttons simultaneously on the remote commander RM-GA016 for a few seconds. Equipment List display 2. 6. + Channel 5 Hotel Mode Off TV / Remote Controls Both Controls Freeze Use Display Key Use AC Power On Setting Unspecify Wide Mode Key Use Standby LED On Initialize Hotel Settings Once completed, the below button operates as a TEST button. 7. Press B/b to select 'Hotel Mode'. Then press 8. Now press B/b then V/v to select 'ON' and press Red Button . . Function settings Hotel Mode On Off Entering Hotel Menu Mode 1. While TV set is on standby, press the following sequence on the remote commander(RM-GA016). 9. The TV set resets and restarts. 10. Now press 'Menu' on the remote commander. 11. The following menu confirms the hotel mode is ON. Language On screen display Red Button Volume (+) Sleep Timer POWER Exiting Hotel Menu Mode 2. When the TV turns on, the indication "Hotel Mode Settings in Progress" appears on the bottom center of the screen. 1. While TV set is ON, press the following sequence on the remote commander(RM-GA016). MUTE On screen display Hotel Mode Settings in Progress 3. Press 'Menu' on the remote commander. 4. The following menu appears on the screen: 2. MENU Volume (+) The TV set restarts and show "Hotel Mode Settings in Progress" on the bottom center of the screen. Menu Favourites Programme List Hotel Mode Settings in Progress External Inputs FM Radio 3. Now press 'Menu' on the remote commander. 4. The following menu confirms the hotel mode is OFF. Settings Hotel Mode Settings 5. Press V/v to select 'Hotel Mode Settings' and press Menu . Favourites Programme List External Inputs FM Radio Settings Hotel Mode Settings – 59 – KLV-26, 32, 37 S550A RM-GA016 Disable Hotel Menu Mode 1. While TV set is on standby, press the following sequence on the remote commander(RM-GA016). TEST On screen display Red Button Volume (-) 2. Press 'Menu' on the remote commander. 3. The below menu appears on the screen. POWER Menu Favourites Programme List External Inputs FM Radio Settings 4. This menu confirms the hotel menu mode is disabled. – 60 – KLV-26, 32, 37 S550A RM-GA016 7-3. CIRCUIT BOARD LOCATION 7-3-1 KLV-26S550A/1, 26S550A/3 (refer page 32) R2 Board (In actual case, R2 board is attached at Rear Cover) 7-3-2 KLV-32S550A/1, 32S550A/3 (refer page 32) R2 Board (In actual case, R2 board is attached at Rear Cover) – 61 – KLV-26, 32, 37 S550A RM-GA016 7-3-3 KLV-37S550A/1, 37S550A/3 (refer page 33) R2 Board (In actual case, R2 board is attached at Rear Cover) – 62 – KLV-26, 32, 37 S550A RM-GA016 7-4. SCHEMATIC DIAGRAM (refer page 34) Board R2 Function Hotel Mode 7-5. PRINTED WIRING BOARDS Note Due to complexity of the board, performing component level field repairs are not recommended. Complete board replacement is required if service is necessary. For part number information, refer to Exploded View or Electrical Parts List section in this manual. – 63 – KLV-26, 32, 37 S550A RM-GA016 SECTION 8 EXPLODED VIEWS 8-1. KLV-26S550A/1, 26S550A/3 8-1-1. R2 BOARD, REAR CABINET AND STAND ASSY (refer page 35) 7 2 REF. NO. PART NO. 2 3 7 8 DESCRIPTION REMARK ---------Not Supply-------------------Not Supply----------* 4-111-643-01 R BRACKET (TOP) * A-1565-554-A R2 MOUNT – 64 – / 3 8 KLV-26, 32, 37 S550A RM-GA016 8-1-2. BOARDS, SPEAKERS, BEZEL AND PANEL (refer Page 36) 58 60 59 REF. NO. PART NO. 58 59 60 DESCRIPTION REMARK * A-1663-488-B HT1 MOUNT * A-1665-115-B GT3 COMPLETE A-1738-901-A BT2 MOUNT (SERVICE) – 65 – KLV-26, 32, 37 S550A RM-GA016 8-2. KLV-32S550A/1, 32S550A/3 8-2-1. R2 BOARD, REAR CABINET AND STAND ASSY (refer Page 36) 7 2 / 3 8 4 1 REF. NO. PART NO. 1 2 3 4 7 8 DESCRIPTION REMARK X-2345-139-2 REAR COVER (32) ASSY X-2348-751-1 REAR COVER (32) ASSY ----------Not Supply------------------Not Supply--------* 4-127-924-02 COVER, ECS(S) * 4-111-643-01 R BRACKET (TOP) * A-1565-554-A R2 MOUNT – 66 – KLV-26, 32, 37 S550A RM-GA016 8-2-2. BOARDS, SPEAKERS, BEZEL AND PANEL (refer Page 37) 60 52 61 58 54 59 55 REF. NO. PART NO. DESCRIPTION 52 ! ! 54 55 58 * 59 * 1-802-932-11 1-802-932-32 X-2515-157-1 X-2515-158-1 A-1663-488-B A-1663-495-B 60 61 A-1739-081-A BT2 MOUNT (SERVICE) 4-103-642-21 EMBLEM, SONY NO.8 REMARK LCD PANEL (32 INCH WXGA TFT) LCD PANEL (32 INCH WXGA TFT) BAFFLE, SP (32/37L) ASSY BAFFLE, SP (32/37R) ASSY HT1 MOUNT GT3 COMPLETE – 67 – KLV-26, 32, 37 S550A RM-GA016 8-3. KLV-37S550A/1, 37S550A/3 8-3-1. R2 BOARD, REAR CABINET AND STAND ASSY (refer Page 38) 7 2 5 REF. NO. PART NO. 2 3 5 7 8 DESCRIPTION REMARK ----------Not Supply------------------Not Supply--------X-2345-159-2 STAND ASSY (ML1) * 4-111-643-01 R BRACKET (TOP) * A-1565-554-A R2 MOUNT – 68 – / 3 8 KLV-26, 32, 37 S550A RM-GA016 8-3-2. BOARDS, SPEAKERS, BEZEL AND PANEL (refer Page 39) 54 64 58 60 55 59 REF. NO. PART NO. 54 55 56 58 59 60 64 X-2515-157-1 X-2515-158-1 4-125-786-02 * A-1663-488-B 1-474-161-12 DESCRIPTION REMARK BAFFLE, SP (32/37L) ASSY BAFFLE, SP (32/37R) ASSY COVER, UNDER (37) HT1 MOUNT POWER UNIT A-1739-123-A BT2 MOUNT (SERVICE) 4-103-642-21 EMBLEM, SONY NO.8 – 69 – 56 KLV-26, 32, 37 S550A RM-GA016 SECTION 9 ELECTRICAL PARTS LIST REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. 9-1. KLV-26S550A/1, 26S550A/3 * 1-910-053-52 * 1-910-049-38 ********************************************************************** 1-836-846-11 ACCESORIES AND PACKING MATERIALS ************************************** 4-130-985-23 4-130-985-33 4-130-985-43 4-130-985-54 4-130-985-63 1-836-846-21 * 1-910-053-25 BAG ASSY, FALL LOCK BELT CUSHION LOWER CUSHION UPPER INDIVIDUAL CARTON MANUAL, INSTRUCTION MISCELLANEOUS ***************** MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION 4-100-136-01 SHEET(CORE), C (FRM MAIN(5) FRM BTM(2) FRM SPN(2) PANEL(1) SP(2) ********************************************************************* 9-3. KLV-37S550A/1, 37S550A/3 CONNECTORS ************** CONNECTOR ASSY 6P (CN001(R2)-C9003(BG1)(1)(FOR EG1L(GA)ONLY)/ CN001(R2)-CN3003(BT2)(1)(FOR EX2T ONLY)) A-1739-123-A * A-1663-488-B 1-474-161-12 * A-1565-554-A BT2 MOUNT (SERVICE) HT1 MOUNT POWER UNIT R2 MOUNT ********************************************************************* ********************************************************************** ACCESORIES AND PACKING MATERIALS ************************************** MISCELLANEOUS ***************** 4-100-136-01 CONNECTOR ASSY 14P (INV-CN6201(GT3)-CN7001(BT2)(1) CONNECTOR ASSY 6P (CN001(R2)-C9003(BG1)(1)(FOR EG1L(GA)ONLY)/ CN001(R2)-CN3003(BT2)(1)(FOR EX2T ONLY) LEAD WIRE WITH CONNECTOR(LVDS) (CN3000(BT2)-TCON(1) LEAD WIRE WITH CONNECTOR(LVDS) (CN3000(BT2)-TCON(1) SP CONNECTOR ASSY 4P (CN2000(BT2)-SP(1) *********************************************************************** *********************************************************************** * 1-910-049-38 REMARK CONNECTORS ************** A-1738-901-A BT2 MOUNT (SERVICE) * A-1665-115-B GT3 COMPLETE * A-1663-488-B HT1 MOUNT * A-1565-554-A R2 MOUNT X-2342-530-2 * 4-140-605-01 * 4-140-604-01 * 4-127-335-02 4-130-985-13 DESCRIPTION X-2342-530-2 * 4-140-603-01 4-130-985-13 4-130-985-23 4-130-985-33 SHEET(CORE), C (MAIN BKT(4) FRM BTM(1) FRM SPN(1) PANEL(2)) BAG ASSY, FALL LOCK BELT INDIVIDUAL CARTON MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION ********************************************************************** 4-130-985-43 4-130-985-54 4-130-985-63 9-2. KLV-32S550A/1, 32S550A/3 A-1739-081-A BT2 MOUNT (SERVICE) * A-1663-495-B GT3 COMPLETE * A-1663-488-B HT1 MOUNT * A-1565-554-A R2 MOUNT ********************************************************************** ********************************************************************** ACCESORIES AND PACKING MATERIALS ************************************** X-2348-141-2 * 4-140-606-01 4-130-985-13 4-130-985-23 4-130-985-33 4-130-985-43 4-130-985-54 4-130-985-63 MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION BAG ASSY(L), FALL LOCK BELT INDIVIDUAL CARTON MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION MANUAL, INSTRUCTION ********************************************************************** – 70 – KLV-26, 32, 37 S550A RM-GA016 REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK CONNECTORS ************** * 1-910-049-38 1-836-566-21 CONNECTOR ASSY 6P (CN001(R2)-C9003(BG1)(1) (FOR EG1L(GA)ONLY)/ CN001(R2)-CN3003(BT2)(1)(FOR EX2T ONLY)) LEAD WIRE WITH CONNECTOR(LVDS) (CN3000(BT2)-TCON(1)) Sony Corporation 9-888-103-06 Sony EMCS (Malaysia) Sdn. Bhd. TVEG – 71 – English ¹ 2009.7 Specifications Model name System Panel System TV System Colour System Channel Coverage Sound Output Input/Output jacks Antenna 1, 2 1, 2 KLV-37S550A KLV-32S550A KLV-32S530A KLV-26S550A LCD (Liquid Crystal Display) Panel B/G, I, D/K, M PAL, PAL60, SECAM, NTSC4.43, NTSC3.58 B/G: VHF: E2 to E12/ UHF: E21 to E69/ CATV: S01 to S03, S1 to S41 VHF: 1 to 11/UHF: 21 to 69/ CATV: S01 to S03, S1 to S41 (New Zealand only) I: UHF: B21 to B69/ CATV: S01 to S03, S1 to S41 D/K: VHF: C1 to C12, R1 to R12/ UHF: C13 to C57, R21 to R60/ CATV: S01 to S03, S1 to S41, Z1 to Z39 M: VHF: A2 to A13/ UHF: A14 to A79/ CATV: A-8 to A-2, A to W+4, W+6 to W+84 10 W + 10 W 8W+8W 75 ohm external terminal Video input (phono jack) Audio input (phono jacks): 500 mVrms, Impedance: 47 kilohms Supported formats: 1080p (50/60 Hz), 1080i (50/60 Hz), 720p (50/60 Hz), 576p, 576i, 480p, 480i Y: 1 Vp-p, 75 ohms, 0.3V sync negative/PB/CB: 0.7 Vp-p, 75 ohms/PR/CR: 0.7 Vp-p, 75 ohms Audio input (phono jacks): 500 mVrms, Impedance: 47 kilohms Video output (phono jack) Audio output (phono jacks) HDMI IN (KLV-32S530A) HDMI IN 1, 2 (KLV-37S550A/ KLV-32S550A/KLV-26S550A) PC IN (RGB) PC IN i Power and others Power Requirements Video: 1080p (50/60 Hz), 1080i (50/60 Hz), 720p (50/60 Hz), 576p, 576i, 480p, 480i PC Input (D-sub 15-pin) (see page 21) G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/ R: 0.7 Vp-p, 75 ohms/HD: 1-5 Vp-p/VD: 1-5 Vp-p PC audio input (minijack) Headphones jack 110–240 V AC, 50/60 Hz 220–240 V AC, 50/60 Hz (New Zealand and Tunisia only) 37 32 Screen Size (inches) 1,366 pixels (horizontal) × 768 lines (vertical) Display Resolution Indicated on the rear of the TV. Power Consumption 927 × 627 × 259 807 × 557 × 222 Dimensions with stand (mm) (w × h × d)* without stand 927 × 574 × 103 807 × 508 × 102 (mm) 16.1 13.1 Mass* with stand (kg) without stand 14.3 12.0 (kg) Optional Wall-Mount SU-WL500 or SU-WL50B Accessories bracket 26 807 × 557 × 222 679 × 485 × 222 807 × 508 × 102 679 × 435 × 101 13.1 10.0 12.0 8.7 SU-WL100 * Dimensions and mass are approximate values. Design and specifications are subject to change without notice. Instructions on “Installing the Wall-Mount Bracket” are not supplied in the form of a separate leaflet with this TV. These installation instructions are included within this TV’s instructions manual. Printed on 70% or more recycled paper using VOC (Volatile Organic Compound)-free vegetable oil based ink. Printed in Malaysia Customer support