Download SDM-M51 - Linfotech.co.uk

SDM-M51
SERVICE MANUAL
US Model
Canadian Model
AEP Model
SPECIFICATIONS
LCD panel
Input signal format
Resolution
Input signal levels
Audio output
Headphones jack
AUDIO IN jack
Power requirements
DC input
Power consumption
Operating temperature
Panel type: a-Si TFT Active Matrix
Picture size: 15.1 inch
RGB operating frequency*
Horizontal: 28 – 64 kHz
Vertical: 48 – 75 Hz
Horizontal: Max.1024 dots
Vertical: Max.768 lines
RGB video signal
0.7 Vp-p, 75 Ω, positive
SYNC signal
TTL level, 2.2 kΩ,
positive or negative
(Separate horizontal and vertical,
or composite sync)
0.3 Vp-p, 75Ω, negative
(Sync on green)
1W×2
Stereo minijack
Accepts impedance of 16 – 48 Ω
Stereo minijack
Accepts impedance of 47 kΩ
Accepts level 0.5 Vrms
100 – 240 V, 50 – 60 Hz,
0.4 – 0.2 A
DC 18 V (supplied AC adapter)
Max. 19 W
Max. 22 W (including AC adapter)
5 – 35 ˚C
Dimensions (width/height/depth)
Display (upright):
Approx. 387 × 345 × 180 mm
(15 1/4 × 13 5/8 × 7 1/8 inches)
(with stand)
Approx. 387 × 296 × 48 mm
(15 1/4 × 11 3/4 × 1 15/16 inches)
(without stand)
Mass
Approx. 4.6 kg (10 lb 14 oz) (with
stand)
Plug & Play
DDC1/DDC2B/DDC2Bi
Accessories
See page 7.
* Recommended horizontal and vertical timing condition
• Horizontal sync width duty should be more than 4.8% of
total horizontal time or 0.8 µs, whichever is larger.
• Horizontal blanking width should be more than 2.5 µsec.
• Vertical blanking width should be more than 450 µsec.
Design and specifications are subject to change without notice.
TFT LCD COLOR COMPUTER DISPLAY
SDM-M51
Power saving function
Automatic picture quality
adjustment function
This monitor meets the power-saving guidelines set by VESA,
ENERGY STAR, and NUTEK. If the monitor is connected to a
computer or video graphics board that is DPMS (Display Power
Management Signaling) compliant, the monitor will automatically
reduce power consumption in three stages as shown below.
Power mode
Power
consumption*
1 (power)
indicator
normal
operation
19 W (22 W)
green
active off**
(deep sleep)*
1 W (2 W)
orange***
power off
1 W (2 W)
off
When the monitor receives an input signal, it automatically
matches the signal to one of the factory preset modes stored in the
monitor’s memory to provide a high quality picture at the center
of the screen. (See Appendix for a list of the factory preset
modes.)
For input signals that do not match one of the factory preset
modes, the automatic picture quality adjustment function of this
monitor automatically adjusts the picture position, phase, and
pitch, and ensures that a clear picture appears on the screen for
any timing within the monitor’s frequency range (horizontal: 28 –
64 kHz, vertical: 48 – 75 Hz).
Consequently, the first time the monitor receives input signals
that do not match one of the factory preset modes, the monitor
may take a longer time than normal for displaying the picture on
the screen. This adjustment data is automatically stored in
memory so that next time, the monitor will function in the same
way as when the monitor receives the signals that match one of
the factory preset modes.
In all modes as above, if the picture is adjusted, the adjustment
data is stored as a user mode and automatically recalled whenever
the same input signal is received.
*
“deep sleep” is the power saving mode defined by the Environmental
Protection Agency.
** When your computer enters the “active off” mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After 20 seconds,
the monitor enters the power saving mode.
*** If the horizontal or vertical sync signal is received by the monitor, the
power indicator may alternately blink green and orange.
Note
While the automatic picture quality adjustment function is activated, only
the 1 (power) switch will operate.
–2–
SDM-M51
TIMING SPECIFICATION
PRESET MODE
MODE 1
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
MODE 7
MODE 8
SIGNAL MODE
VESA 75Hz
VESA 60Hz
MAC 66Hz
VESA 75Hz
VESA 70Hz
VESA 56Hz
VESA 60Hz
VESA 72Hz
RESOLUTION
640 X 480
640 X 480
640 X 480
720 X 400
800 X 600
800 X 600
800 X 600
800 X 600
DOT CLOCK
25.175 MHz
30.240 MHz
31.500 MHz
28.350 MHz
36.000 MHz
40.000 MHz
50.000 MHz
49.500 MHz
usec
usec
usec
usec
usec
usec
usec
usec
H. TOTAL
31.778
28.571
26.667
31.746
28.444
26.400
20.800
20.110
H. SYNC
3.813
2.116
2.032
3.810
0.889
3.200
2.400
1.616
H. BP
1.907
3.175
3.810
1.905
4.667
2.200
1.280
3.232
H. ACTIV
25.422
21.164
20.317
25.397
22.222
20.000
16.000
16.162
VERTICAL
msec
msec
msec
msec
msec
msec
msec
msec
V. TOTAL
16.683
15.000
13.333
14.254
17.778
16.579
13.853
13.333
V. SYNC
0.064
0.086
0.080
0.095
0.057
0.106
0.125
0.064
V. BP
1.049
1.114
0.427
1.079
0.626
0.607
0.478
0.448
V. ACTIV
15.253
13.714
12.800
12.698
17.067
15.840
12.480
12.800
H/V POLARITY
N/N
N/N
N/N
N/P
N/N
P/P
N/N
P/P
PRESET MODE
MODE 9
MODE 10
MODE 11
MODE 12
MODE 13
SIGNAL MODE
PMAC 16"
VESA 60Hz
VESA 70Hz
VESA 75Hz
MAC 768 75Hz
RESOLUTION
832X 624
1024X 768
1024X 768
1024X 768
1024X 768
DOT CLOCK
57.285 MHz
65.000 MHz
75.000 MHz
78.750 MHz
80.000 MHz
usec
usec
usec
usec
usec
H. TOTAL
20.110
20.677
17.707
16.660
16.600
H. SYNC
1.117
2.092
1.813
1.219
1.200
H. BP
3.910
2.462
1.920
2.235
2.200
H. ACTIV
14.524
15.754
13.653
13.003
12.800
VERTICAL
msec
msec
msec
msec
msec
V. TOTAL
13.413
16.666
14.272
13.328
13.346
V. SYNC
0.060
0.124
0.106
0.050
0.050
V. BP
0.744
0.600
0.513
0.466
0.498
V. ACTIV
12.549
15.880
13.599
12.795
12.749
N/N
N/N
N/N
P/P
N/N
HORIZONTAL
HORIZONTAL
H/V POLARITY
–3–
SDM-M51
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values.
Make sure your instruments are accurate; be suspicious of
your HV meter if sets always have low HV.
8. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for AC
Leakage. Check leakage as described below.
To Exposed Metal
Parts on Set
0.15 µF
1.5 k Ω
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500
microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to
use these instruments.
2. A battery-operated AC milliammeter. The Data Precision
245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOMs that are suitable. Nearly all
battery operated digital multimeters that have a 2 V AC
range are suitable. (See Fig. A)
WARNING!!
NEVER TURN ON THE POWER IN A CONDITION IN
WHICH THE DEGAUSS COIL HAS BEEN REMOVED.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
¡ ON THE SCHEMATIC DIAGRAMS, EXPLODED
VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR
SAFE OPERATION. REPLACE THESE COMPONENTS
WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION
ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE
PROCEDURES WHENEVER CRITICAL COMPONENTS
ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED.
AVERTISSEMENT!!
NE JAMAIS METTRE SOUS TENSION QUAND LA
BOBINE DE DEMAGNETISATION EST ENLEVÉE.
ATTENTION AUX COMPOSANTS RELATIFS À LA
SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET
UNE MARQUE ¡ SONT CRITIQUES POUR LA SÉCURITÉ.
NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE
NUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT
L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU
FONCTIONNEMENT SONT IDENTIFIÉS DANS LE
PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS
DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU’UN MAUVAIS FONCTIONNEMENT
EST SUSPECTÉ.
–4–
SDM-M51
TABLE OF CONTENTS
Section
Title
Page
1. GENERAL .................................................................. 1-1
2. DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
Bezel Assy, and Back Cabinet Removal ........... 2-1
TFT Panel and H Board Removal ........................ 2-2
DC-AC Inverter Removal .................................. 2-2
A Board and J2 Board Removal ......................... 2-3
J1 Board Removal ............................................... 2-4
3. ADJUSTMENTS
3-1.
3-2.
Adjusment (1) ..................................................... 3-1
Adjusment (2) ..................................................... 3-2
4. DIAGRAMS
4-1.
4-2.
4-3.
(1)
(2)
(3)
4-4.
Block Diagrams .................................................... 4-1
Circuit Boards Location ...................................... 4-3
Schematic Diagrams and Printed Wiring Boards ... 4-3
Schematic Diagram of H Board ........................... 4-4
Schematic Diagram of A (a-c) Board .................. 4-5
Schematic Diagram of J, J2 Board ....................... 4-12
Semiconductors ................................................... 4-14
5. EXPLODED VIEWS
5-1.
5-2.
Chassis ................................................................. 5-1
Packing Materials ................................................ 5-2
6. ELECTRICAL PARTS LIST ............................ 6-1
–5–
SECTION 1
GENERAL
About the built-in stereo speaker
Precautions
Warning on power connections
• Use the supplied power cord. If you use a different power cord,
be sure that it is compatible with your local power supply.
For the customers in the U.S.A.
If you do not use the appropriate cord, this monitor will not
conform to mandatory FCC standards.
For the customers in the UK
If you use the monitor in the UK, be sure to use the appropriate
UK power cord.
Example of plug types
Be sure to keep magnetic recording equipment, tapes, and floppy
discs away from the speaker’s opening as the speakers generate a
magnetic field. This magnetic field may affect data stored on
magnetic tapes and discs.
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remein as in the manual.
See the pages in parentheses for further details.
Front of the LCD display
2 MENU button (pages 11, 12)
This button displays the main menu.
About the bright points of light or black dots
Bright points of light (red, blue or green) or black dots
may appear on the LCD screen. This is not a
malfunction. The LCD screen is made with highprecision technology and more than 99.99 % of the
picture element is intact. However, some of the picture
element may not appear or some of the picture element
may appear constantly.
MENU
OK
for 200 to 240 V AC
for 240 V AC only
For use only with power supply LIEN, LE-9702B-01A
The equipment should be installed near an easily accessible outlet.
1-1
Installation
Do not install or leave the monitor:
• In places subject to extreme temperatures, for example near a
radiator, heating vent, or in direct sunlight. Subjecting the
monitor to extreme temperatures, such as in an automobile
parked in direct sunlight or near a heating vent, could cause
deformations of the casing or malfunctions.
• In places subject to mechanical vibration or shock.
• Near any equipment that generates a strong magnetic field,
such as a TV or various other household appliances.
• In places subject to inordinate amounts of dust, dirt, or sand, for
example near an open window or an outdoor exit. If setting up
temporarily in an outdoor environment, be sure to take
adequate precautions against airborne dust and dirt. Otherwise
irreparable malfunctions could occur.
Handling the LCD screen
• Do not leave the LCD screen facing the sun as it can damage
the LCD screen. Take care when you place the monitor by a
window.
• Do not push on or scratch the LCD screen. Do not place a heavy
object on the LCD screen. This may cause the screen to lose
uniformity or cause LCD panel malfunctions.
• If the monitor is used in a cold place, a residual image may
appear on the screen. This is not a malfunction. The screen
returns to normal as the temperature rises to a normal operating
level.
• If a still picture is displayed for a long time, a residual image
may appear for a while. The residual image will eventually
disappear.
• The LCD panel becomes warm during operation. This is not a
malfunction.
A specially designed fluorescent tube is installed as the lighting
apparatus for this monitor. If the screen becomes dark, unstable,
or does not turn on, replace the fluorescent tube with a new one.
Consult your Sony dealer when replacing the fluorescent tube.
4 8 (brightness) button (page 12)
This button displays the BRITGHTNESS menu.
6 OK button (page 12)
This button selects the item or executes the settings in the
menu.
Maintenance
• Be sure to unplug the power cord from the power outlet before
cleaning your monitor.
• Clean the LCD screen with a soft cloth. If you use a glass
cleaning liquid, do not use any type of cleaner containing an
anti-static solution or similar additive as this may scratch the
LCD screen’s coating.
• Clean the cabinet, panel, and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder, or solvent, such as alcohol or
benzine.
• Do not rub, touch, or tap the surface of the screen with sharp or
abrasive items such as a ballpoint pen or screwdriver. This type
of contact may result in a scratched picture tube.
• Note that material deterioration or LCD screen coating
degradation may occur if the monitor is exposed to volatile
solvents such as insecticide, or if prolonged contact is
maintained with rubber or vinyl materials.
3 6 (contrast) button (page 12)
This button displays the CONTRAST menu.
5 2 (volume) +/– and M(+)/m(–) buttons (pages 9, 12)
These buttons display the VOLUME menu and function as
the M(+)/m(–) buttons when selecting the menu items and
making adjustments.
Replacement of the fluorescent tube
for 100 to 120 V AC
1 1 (Power) switch and indicator (pages 9, 17, 21)
This switch turns the display on and off.
The power indicator lights up in green when the display is
turned on, and either flashes in green and orange, or lights up
in orange when the monitor is in power saving mode.
Identifying parts and controls
7 Stereo speaker (page 9)
This outputs the audio signals as sound.
Side view of the LCD display
GB
8 Headphones jack (page 9)
This jack outputs audio signals to the headphones.
9 Security Lock Hole ( )
The security lock hole should be applied with the Kensington
Micro Saver Security System.
Micro Saver Security System is a trademark of Kensington.
Transportation
• Disconnect all cables from the monitor and grasp the support
and base sections of the display stand firmly with both hands
when transporting. If you drop the monitor, you may be injured
or the monitor may be damaged.
• When you transport this monitor for repair or shipment, use the
original carton and packing materials.
Rear of the display stand
Disposal of the monitor
• Do not dispose of this monitor with general
household waste.
• The fluorescent tube used in this monitor contains
mercury. Disposal of this monitor must be carried out
in accordance to the regulations of your local
sanitation authority.
(continued)
4
5
qd HD15 (RGB) input connector/HD15 (RGB) video
signal cable (page 7)
This connector inputs RGB video signals (0.7 Vp-p, positive)
and SYNC signals.
Rear of the LCD display
5 4 3 2 1
10 9 8 7 6
15 14 13 12 11
OPEN
x Connecting to a Macintosh or compatible
computer
Setup
Use the supplied Macintosh adapter.
Before using your monitor, check that the following accessories
are included in your carton:
• LCD display
• Power cord
• AC adapter
• HD15 (RGB) video signal cable (this cable is already
connected to the monitor)
• Audio cord (stereo miniplug)
• Cord clip (2)
• Macintosh adapter
• Windows Monitor Information/Windows Utility/Macintosh
Utility Disk
• Warranty card
• Notes for Macintosh users
• This instruction manual
1-2
Pin No.
Signal
1
Red
2
Green
(Sync on Green)
3
Blue
4
ID (Ground)
5
DDC Ground*
6
Red Ground
7
Green Ground
8
Blue Ground
Step 1: Connect the display to your
computer
9
DDC + 5V*
Turn off the monitor and computer before connecting.
10
Ground
11
ID (Ground)
12
Bi-Directional Data (SDA)*
13
H. Sync
14
V. Sync
15
Data Clock (SCL)*
Note
Do not touch the pins of the video signal cable connector as this might
bend the pins.
Macintosh adapter
(supplied)*
to video output
HD15 (RGB) video
signal cable (supplied)
Macintosh or
compatible computer
* Refer to the supplied “Notes for Macintosh users” for further details.
x Connecting to an IBM PC/AT or compatible
computer
* DDC (Display Data Channel) is a standard of VESA.
qf Cable holder (page 8)
This part secures cables and cords to the monitor.
0 Back cover (page 8)
Open this cover when you connect/disconnect cables or cords.
qa DC IN connector/AC adapter (page 8)
This connector provides DC power to the display. Connect the
AC adapter to this connector.
qs AUDIO IN jack/Audio cord (page 8)
This jack inputs audio signals when connecting to the audio
output jack of the computer or other audio equipment.
to VIDEO output
IBM PC/AT or
compatible computer
HD 15 (RGB) video
signal cable (supplied)
(continued)
6
7
GB
Step 2: Connect the audio cord
Open the back cover and turn off the display before connecting.
Note
Do not open the back cover more than 90 degrees, otherwise damage may
result to the back cover or latch.
Step 4: Secure the cords and close
the back cover
Step 5: Turn on the monitor and
computer
1 Remove the cable holder.
1 Press the 1 (power) switch.
The indicator of the monitor lights up in green.
Adjusting the monitor’s resolution and color number
Adjust the monitor’s resolution and color number by referring to your
computer’s instruction manual. The color number may vary according to
your computer or video board. The color palette setting and the actual
number of colors are as follows:
• High Color (16 bit) t 65,536 colors
• True Color (24 bit) t about 16.77 million colors
In true color mode (24 bit), speed may be slower.
Using the stereo speaker
to audio input
You can listen to music, sounds, and other audio files using the
stereo speaker of your monitor.
Cable holder
Adjusting the volume
2 Turn on the computer.
OPEN
2 Secure the cables and cords with the cable holder.
The installation of your monitor is complete. If necessary, use the
monitor’s controls to adjust the picture.
Volume adjustments are made using a separate VOLUME menu
from the main menu (page 11).
1 Press the 2 +/– buttons.
The VOLUME menu appears on the screen.
If no picture appears on your screen
Step 3: Connect the power cord
3 Close the back cover.
• Check that the monitor is correctly connected to the computer.
• If NO INPUT SIGNAL appears on the screen, the computer is
in the power saving mode. Try pressing any key on the
keyboard or moving the mouse.
• If CABLE DISCONNECTED appears on the screen, check that
the video input cable is properly connected.
• If OUT OF SCAN RANGE appears on the screen, reconnect
the old monitor. Then adjust the computer’s graphic board so
that the horizontal frequency is between 28 – 64 kHz, and the
vertical frequency is between 48 – 75 Hz.
With the monitor and computer switched off, first connect the AC
adapter and power cord to the monitor, then connect it to a power
outlet.
Bandle the cables and cords
For more information about the on-screen messages, see “Trouble
symptoms and remedies” on page 19.
to audio input of the
computer or other audio
equipment
audio cord (supplied)
Cable
holder
1-3
to DC IN
You can bandle the cables and cords by using the supplied cord
clip.
For customers using Windows 95/98/2000
To maximize the potential of your monitor, install the new model
information file from the supplied Windows Monitor Information Disk
onto your PC.
This monitor complies with the “VESA DDC” Plug & Play standard. If
your PC/graphics board complies with DDC, select “Plug & Play Monitor
(VESA DDC)” or this monitor’s model name as the monitor type in the
“Control Panel” of Windows 95/98/2000. If your PC/graphics board has
difficulty communicating with this monitor, load the Windows Monitor
Information Disk and select this monitor’s model name as the monitor
type.
OPEN
OPEN
Cord clip
VOL UME
40
GB
2 Press the 2 +/– button to adjust the volume.
The menu automatically disappears after about 5 seconds.
Using the headphones jack
You can listen to the audio signals from your computer or other
audio equipment using headphones. Connect your headphones to
the headphones jack. The speaker turns off when headphones are
connected to the headphones jack. Adjust the volume of the
headphones using the VOLUME menu.
Notes
• You cannot adjust the volume when displaying the main menu on the
screen.
• When your monitor is in power saving mode, no sound comes from the
speaker.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 is different from Windows 95/98/2000
and does not involve the selection of monitor type. Refer to the Windows
NT4.0 instruction manual for further details on adjusting the resolution,
refresh rate, and number of colors.
to a power outlet
power cord (supplied)
AC adapter (supplied)
8
9
3 Grasp the lower sides of the LCD panel, then adjust
Adjusting the tilt and height
screen height.
Customizing Your Monitor
This display can be adjusted within the angles shown below.
Before making adjustments
4 V CENTER (page 13)
Select the V CENTER menu
to adjust the picture’s vertical
centering.
V CENT ER
50
Connect the monitor and the computer, and turn them on.
Wait for at least 30 minutes before making adjustments for the
best result.
70˚
You can make numerous adjustments to your monitor using the
on-screen menu.
30˚
Navigating the menu
EX I T
5 COLOR (page 14)
Select the COLOR menu to
adjust the color temperature
of the picture. This adjusts
the tone of the screen.
COLOR
9 30 0K
6 5 00K
5 0 0 0K
USER
L A D J U ST
40˚
Press the MENU button to display the main menu on your screen.
See page 12 for more information on using the MENU button.
64˚
To adjust the angles, follow the procedure of the steps below.
1 Grasp the lower middle part of the display while
holding the display stand, then, tilt the LCD panel
adequately backward.
PHA SE
Note
When adjusting the screen tilt and height, proceed slowly and carefully,
being sure not to hit the LCD panel against the desk or the base of the
display stand.
EX I T
6 MENU POSITION
(page 14)
Select the MENU
POSITION to change the onscreen menu position.
MENU
,
MEN U POS I T I ON
To use the display comfortably
This display is designed so that you can set it up at a comfortable
viewing angle. Adjust the viewing angle of your display
according to the height of the desk and chair, and so that light is
not reflected from the screen to your eyes.
1-4
2 Grasp the lower sides of the LCD panel, then adjust
screen tilt.
EX I T
Use the M(+)/m(–) and OK buttons to select one of the following
menus. See page 12 for more information on using the
M(+)/m(–) and OK buttons.
1 PHASE (page 13)
Select the PHASE menu to
adjust the phase when the
characters or pictures appear
fuzzy throughout the entire
screen. Adjust the phase after
adjusting the pitch.
RESE T
GB
S CREEN RESE T
A L L RESE T
EX I T
PHA S E
30
EX I T
2 PITCH (page 13)
Select the PITCH menu to
adjust the pitch when the
characters or pictures are
unclear in some areas of the
screen.
7 RESET (page 15)
Select the RESET menu to
reset the adjustments.
P I TCH
8 Option (page 15)
Select m (option) menu to
adjust the monitor’s options.
The options include:
• BACKLIGHT
• POWER SAVE
• LANGUAGE
• MENU LOCK
BACK L I GH T
10 0
EX I T
1344
EX I T
3 H CENTER (page 13)
Select the H CENTER menu
to adjust the picture’s
horizontal centering.
H CENT ER
50
EX I T
(continued)
10
11
x Using the MENU, M(+)/m(–), and OK buttons
1 Display the main menu.
Press the MENU button to display the main menu on your
screen.
Adjusting the contrast (CONTRAST)
Contrast adjustment is made using a separate CONTRAST menu
from the main menu (page 11).
1 Press the 6 (contrast) button.
MENU
The CONTRAST menu appears on the screen.
CONTRAS T
70
2 Select the menu you want to adjust.
Press the M(+)/m(–) buttons to display the desired menu.
Press the OK button to select the menu item.
,
OK
4 8 . 4 kHz /
Horizontal frequency
of the current input
signal
6 0Hz
Vertical frequency of
the current input
signal
Displaying the current input signal
The horizontal and vertical frequencies of the current input signal are
displayed in the CONTRAST and BRIGHTNESS menu.
2 Press the M(+)/m(–) buttons to adjust the contrast.
3 Adjust the menu.
The menu automatically disappears after about 5 seconds.
Press the M(+)/m(–) buttons to make the adjustment, then
press the OK button.
When you press the OK button, the setting are stored, then the
display returns to the previous menu.
1-5
,
OK
Eliminating flicker or blurring
(PHASE/PITCH)
When the monitor receives an input signal, the automatic picture
quality adjustment function of this monitor automatically adjusts
the picture position, phase, and pitch, and ensures that a clear
picture appears on the screen. For more information about this
function, see “Automatic picture quality adjustment function” on
page 17.
For some input signals, this function may not completely adjust
the picture position, phase, and pitch. In this case, you can
manually set these adjustments according the following
instructions. If you manually set these adjustments, they are
stored in memory and automatically recalled whenever the
monitor receives the same input signals.
These settings may have to be repeated if you change the input
signal after reconnecting your computer.
1 Set the resolution to 1024 × 768 on the computer.
2 Load the Utility Disk.
3 Start the Utility Disk and display the test pattern.
For Windows 95/98/2000
Click [Utility] t [Windows]/[Win Utility.exe].
For Macintosh
Click [Utility] t [Mac]/[Mac Utility].
Adjusting the black level of an
image (BRIGHTNESS)
4 Press the MENU button.
Brightness adjustment is made using a separate BRIGHTNESS
menu from the main menu (page 11).
5 Press the M(+)/m(–) buttons to select
1 Press the 8 (brightness) button.
The BRIGHTNESS menu appears on the screen.
4 Close the menu.
Press the MENU button once to return to normal viewing. If
no buttons are pressed, the menu closes automatically after
about 30 seconds.
The main menu appears on the screen.
6 0Hz
and press the OK button.
The PITCH menu appears on the screen.
6 Press the M(+)/m(–) buttons until the vertical stripes
,
MENU
Horizontal frequency
of the current input
signal
Vertical frequency of
the current input
signal
2 Press the M(+)/m(–) buttons to adjust the
brightness.
x Resetting the adjustments
The menu automatically disappears after about 5 seconds.
You can reset the adjustments using the RESET menu. See
page 15 for more information on resetting the adjustments.
If the screen is too bright
9 Press the M(+)/m(–) buttons until the horizontal
stripes are at a minimum.
Adjust so that the horizontal stripes are at a minimum.
,
10 Click [END] on the screen to turn off the test pattern.
To reset the automatic picture quality adjustment
Select SCREEN RESET and activate it using the RESET menu. See
page 15 for more information on using the RESET menu.
Adjusting the picture position
(H CENTER/V CENTER)
1 Start the Utility Disk and display the test pattern.
(PITCH)
50
4 8 . 4 kHz /
(PHASE)
and press the OK button.
The PHASE menu appears on the screen.
If the picture is not in the center of the screen, adjust the picture’s
centering as follows.
These settings may have to be repeated if you change the input
signal after reconnecting your computer.
disappear.
Adjust so that the vertical stripes disappear.
B R I GHT NESS
8 Press the M(+)/m(–) buttons to select
7 Press the OK button.
The main menu appears on the screen.
If horizontal stripes are observed over the entire screen, adjust
the phase as the next step.
Repeat steps 2 and 3 of “Eliminating flicker or blurring
(PHASE/PITCH).”
2 Press the MENU button.
The main menu appears on the screen.
3 Press the M(+)/m(–) buttons to select
(H
CENTER) or
(V CENTER) and press the OK
button.
The H CENTER or V CENTER menu appears on the screen.
4 Move the picture up, down, left, or right until the
frame at the perimeter of the test pattern
disappears.
Press the M(+)/m(–) buttons to adjust the picture’s
centering using the H CENTER menu for horizontal
adjustment, or the V CENTER menu for vertical
adjustment.
5 Click [END] on the screen to turn off the test pattern.
Adjust the backlight. For more information about adjusting the
backlight see “Adjusting the backlight” on page 15.
Note
You can adjust neither contrast nor brightness when displaying the main
menu on the screen.
12
13
GB
Adjusting the color temperature
(COLOR)
The COLOR settings allow you to adjust the picture’s color
temperature by changing the color level of the white color field.
Colors appear reddish if the temperature is low, and bluish if the
temperature is high.
9300K is generally suitable for word processing and other text
oriented applications, and 6500K is generally suitable for video
images.
You can set the color temperature to 9300K, 6500K, 5000K or
user adjustment.
1 Press the MENU button.
The main menu appears on the screen.
2 Press the M(+)/m(–) buttons to select
(COLOR)
and press the OK button.
3 Press the M(+)/m(–) buttons to select the desired
color temperature and press the OK button.
The preset color temperatures are 9300K, 6500K, and 5000K.
Since the default setting is 9300K, the whites will change
from a bluish hue to a reddish hue as the temperature is
lowered to 6500K and 5000K.
4 If necessary, fine tune the color temperature.
1-6
First press the M(+)/m(–) buttons to select ADJUST and
press the OK button. Then press the M(+)/m(–) buttons to
select R (Red) or B (Blue) and press the OK button, and then
press the M(+)/m(–) buttons to adjust the color temperature
and press the OK button. Since this adjustment changes the
color temperature by increasing or decreasing the R and B
components with respect to G (green), the G component is
fixed.
USE R AD J UST MENT
R
G
B
GAMMA
16 8
17 0
17 5
1
2
EX I T
3
To change the GAMMA setting
You can select the GAMMA setting from [1] - [3]. The highest
setting is [3].
1 Press the MENU button.
The main menu appears on the screen.
2 Press the M(+)/m(–) buttons to select
USE R AD J UST MENT
16 8
17 0
17 5
2
You can adjust the following options:
• BACKLIGHT
• POWER SAVE
• LANGUAGE
• MENU LOCK
The main menu appears on the screen.
and press the OK button.
Reset the settings according to the following instructions.
First press the M(+)/m(–) buttons to select ADJUST and
press the OK button. Then press the M(+)/m(–) buttons to
select GAMMA and press the OK button, and then press the
M(+)/m(–) buttons to select [1] -[3] and press the OK button.
1
This monitor has the following two reset methods. Use the
RESET menu to reset the adjustments.
2 Press the M(+)/m(–) buttons to select 0 (RESET)
3 Change the GAMMA setting.
GAMMA
Additional settings (Option)
1 Press the MENU button.
(COLOR)
and press the OK button.
The COLOR menu appears on the screen.
R
G
B
Resetting the adjustments (RESET)
3
If you fine tune the color temperature or change the GAMMA
setting, the new setting is stored in memory for USER
ADJUSTMENT and automatically recalled whenever USER
is selected.
To return to the main menu
Press the M(+)/m(–) buttons to select
button.
, then press the OK
The main menu appears on the screen.
2 Press the M(+)/m(–) buttons to select m.
Resetting the adjustment data most appropriately
for the current input signal
Press the M(+)/m(–) buttons to select SCREEN RESET
and press the OK button.
The automatic picture quality adjustment function of this monitor
automatically adjusts the picture position, phase, and pitch, to the
most appropriate value.
The RESET menu is automatically returned to the main menu
after the adjustment data is reset.
Resetting all of the adjustment data
EX I T
1 Press the MENU button.
Press the M(+)/m(–) buttons to select ALL RESET and
press the OK button.
The RESET menu is automatically returned to the main menu
after the adjustment data is reset.
The option menu appears on the screen.
3 Press the M(+)/m(–) buttons to select the desired
option item and press the OK button.
Adjust the selected option item according to the following
instructions.
Adjusting the backlight
If the screen is too bright, adjust the backlight.
First press the M(+)/m(–) buttons to select
(BACKLIGHT) and press the OK button. Then press
the M(+)/m(–) buttons to adjust the desired light level.
BACK L I GH T
GB
To cancel resetting
10 0
Press the M(+)/m(–) buttons to select
and press the
OK button.
The RESET menu returns to the main menu without resetting the
adjustment data.
EX I T
Setting up the power saving mode
Changing the menu’s position
(MENU POSITION)
You can change the menu position if it is blocking an image on
the screen.
1 Press the MENU button.
The main menu appears on the screen.
2 Press the M(+)/m(–) buttons to select
(MENU
POSITION) and press the OK button.
This monitor has a function which enables it to enter the power
save mode automatically according to the power saving settings
of the computer. You can prevent the monitor from entering the
power saving mode by setting the following option to OFF.
For more information of the power saving mode, see page 17.
First press the M(+)/m(–) buttons to select ZZ... (POWER
SAVE) and press the OK button. Then press the
M(+)/m(–) buttons to select either ON or OFF.
POWER S A V E
ON
OF F
3 Press the M(+)/m(–) buttons to select the desired
position and press the OK button.
There are three positions each for the top of the screen and the
bottom of the screen, and one for the screen center.
EX I T
(continued)
14
15
Selecting the on-screen menu language
English, German, French, Spanish, Italian and Japanese versions
of the on-screen menus are available. The default setting is
English.
First press the M(+)/m(–) buttons to select
(LANGUAGE) and press the OK button. Then press
the M(+)/m(–) button to select a language and press the
OK button.
L ANGUAGE
ENGL I SH
DEUT SCH
F RAN Ç A I S
E S PA Ñ O L
I T A L I AN O
EX I T
•
•
•
•
•
•
ENGLISH
DEUTSCH: German
FRANÇAIS: French
ESPAÑOL: Spanish
ITALIANO: Italian
: Japanese
Technical Features
Power saving function
This monitor meets the power-saving guidelines set by VESA,
ENERGY STAR, and NUTEK. If the monitor is connected to a
computer or video graphics board that is DPMS (Display Power
Management Signaling) compliant, the monitor will automatically
reduce power consumption in three stages as shown below.
Power mode
Power
consumption*
1 (power)
indicator
normal
operation
19 W (22 W)
green
active off**
(deep sleep)*
1 W (2 W)
orange***
power off
1 W (2 W)
off
*
Locking the menus and controls
First press the M(+)/m(–) buttons to select
(MENU
LOCK) and press the OK button. Then press the M(+)/
m(–) buttons and select ON.
“deep sleep” is the power saving mode defined by the Environmental
Protection Agency.
** When your computer enters the “active off” mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After 20 seconds,
the monitor enters the power saving mode.
*** If the horizontal or vertical sync signal is received by the monitor, the
power indicator may alternately blink green and orange.
Automatic picture quality
adjustment function
When the monitor receives an input signal, it automatically
matches the signal to one of the factory preset modes stored in the
monitor’s memory to provide a high quality picture at the center
of the screen. (See Appendix for a list of the factory preset
modes.)
For input signals that do not match one of the factory preset
modes, the automatic picture quality adjustment function of this
monitor automatically adjusts the picture position, phase, and
pitch, and ensures that a clear picture appears on the screen for
any timing within the monitor’s frequency range (horizontal: 28 –
64 kHz, vertical: 48 – 75 Hz).
Consequently, the first time the monitor receives input signals
that do not match one of the factory preset modes, the monitor
may take a longer time than normal for displaying the picture on
the screen. This adjustment data is automatically stored in
memory so that next time, the monitor will function in the same
way as when the monitor receives the signals that match one of
the factory preset modes.
In all modes as above, if the picture is adjusted, the adjustment
data is stored as a user mode and automatically recalled whenever
the same input signal is received.
Note
While the automatic picture quality adjustment function is activated, only
the 1 (power) switch will operate.
MENU LOC K
1-7
ON
OF F
EX I T
Only the 1 (power) switch, and
(MENU LOCK) of the
option menu will operate. If any other items are selected, the
mark appears on the screen.
To cancel the menu lock
Repeat the procedure above and set and
16
(MENU LOCK) to OFF.
17
GB
If CABLE DISCONNECTED appears on the screen
Troubleshooting
This indicates that the video signal cable has been disconnected
from the currently selected connector.
Before contacting technical support, refer to this section.
Trouble symptoms and remedies
If a problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual.
Use the self-diagnosis function (page 21) if the following recommendations do not resolve the problem.
I NFORMA T I ON
On-screen messages
CAB L E D I SCONNECT ED
Symptom
GO TO POWER SAVE
No picture
If there is something wrong with the input signal, one of the
following messages appears on the screen. To solve the problem,
see “Trouble symptoms and remedies” on page 19.
If OUT OF SCAN RANGE appears on the screen
This indicates that the input signal is not supported by the
monitor’s specifications. Check the following items.
I NFORMA T I ON
GO TO POWER SAVE
The monitor will enter the power saving mode after about 5
seconds from the message is displayed.
If the 1 (power) indicator is not lit,
or if the 1 (power) indicator will not
light up when the 1 (power) switch
is pressed
• Check that the power cord is properly connected.
• Check that the 1 (power) switch is in the “on” position.
If the 1 (power) indicator is green
or flashing orange
• Use the self-diagnostics function (page 21).
If CABLE DISCONNECTED
appears on the screen
• Check that the video signal cable is properly connected and all plugs are firmly seated in
their sockets (page 7).
• Check that the video input connector’s pins are not bent or pushed in.
• A non-supplied video signal cable is connected. If you connect a non-supplied video
signal cable, CABLE DISCONNECTED may appear on the screen before entering the
power saving mode. This is not a malfunction.
If NO INPUT SIGNAL appears on
the screen, or the 1 (power)
indicator is either orange or
alternating between green and
orange
• Check that the video signal cable is properly connected and all plugs are firmly seated in
their sockets (page 7).
• Check that the video input connector’s pins are not bent or pushed in.
OUT OF SCAN RANGE
x x . x kHz /
x xHz
If “xx.x kHz/xx Hz” is displayed
This indicates that either the horizontal or vertical frequency
is not supported by the monitor’s specifications.
The figures indicate the horizontal and vertical frequencies of
the current input signal. The horizontal frequencies above
100 kHz and the vertical frequencies above 100 Hz are
represented by 99.9 kHz and 99 Hz, respectively.
1-8
If “RESOLUTION > XGA” is displayed
This indicates that the resolution is not supported by the
monitor’s specifications.
xProblems caused by the connected computer or other equipment
• The computer is in the power saving mode. Try pressing any key on the keyboard or
moving the mouse.
• Check that your graphic board is attached to the computer properly.
• Check that the computer’s power is “on.”
GB
If OUT OF SCAN RANGE appears
on the screen
xProblems caused by the connected computer or other equipment
• Check that the video frequency range is within that specified for the monitor. If you
replaced an old monitor with this monitor, reconnect the old monitor and adjust the
frequency range to the following:
Horizontal: 28 – 64 kHz, Vertical frequency: 48 – 75 Hz
If using Windows 95/98/2000
• If you replaced an old monitor with this monitor, reconnect the old monitor and do the
following. Select “SONY” from the “Manufactures” list and select “SDM-M51” from the
“Models” list in the Windows 95/98/2000 device selection screen. If “SDM-M51” does
not appear in the “Models” list, try “Plug & Play” or install the newest information of the
Sony Computer Display from the Windows Monitor Information Disk (page 9).
If using a Macintosh system
• When connecting to a Power Mac G3/G4 that has 3 rows of pins, check that the supplied
Macintosh adapter and the video signal cable are properly connected (page 7).
• If you connect to the other version of Macintosh series computer that has 2 rows of pins,
you will need a different adapter (not supplied).
If NO INPUT SIGNAL appears on the screen
This indicates that no signal is input.
Check these items
I NFORMA T I ON
NO I NPUT S I GNA L
GO TO POWER SAVE
GO TO POWER SAVE
The monitor will enter the power saving mode after about 5
seconds from the message is displayed.
Picture flickers, bounces,
oscillates, or is scrambled
• Adjust the pitch and phase (page 13).
• Isolate and eliminate any potential sources of electric or magnetic fields such as other
monitors, laser printers, electric fans, fluorescent lighting, or televisions.
• Move the monitor away from power lines or place a magnetic shield near the monitor.
• Try plugging the monitor into a different AC outlet, preferably on a different circuit.
• Change the orientation of the display.
xProblems caused by the connected computer or other equipment
• Check your graphics board manual for the proper monitor setting.
• Confirm that the graphics mode (VESA, Macintosh 19" Color, etc.) and the frequency of
the input signal are supported by this monitor (Appendix). Even if the frequency is within
the proper range, some graphic boards may have a sync pulse that is too narrow for the
monitor to sync correctly.
• Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture.
(continued)
18
19
Symptom
Check these items
Picture is fuzzy
• Adjust the brightness and contrast (page 12).
• Adjust the pitch and phase (page 13).
Self-diagnosis function
xProblems caused by the connected computer or other equipment
• Set the resolution to XGA (1024 x 768) on your computer.
Picture is ghosting
• Eliminate the use of video cable extensions and/or video switch boxes.
• Check that all plugs are firmly seated in their sockets.
Picture is not centered or sized
properly
• Adjust the pitch and phase (page 13).
• Adjust the picture position (page 13). Note that some video modes do not fill the screen to
the edges.
The picture is dark
• Adjust the brightness (page 12).
• Adjust the backlight (page 12).
• It takes a few minutes for the display to become bright after turning on the monitor.
Wavy or elliptical pattern (moire)
is visible
• Adjust the pitch and phase (page 13).
Color is not uniform
• Adjust the pitch and phase (page 13).
White does not look white
• Adjust the color temperature (page 14).
Monitor buttons do not operate
(
appears on the screen)
• If the menu lock is set to ON, set it to OFF (page 16).
The monitor turns off after a while
• Set the power saving function to OFF (page 15).
xProblems caused by the connected computer or other equipment
• Set the computer’s power saving setting to off.
Displaying this monitor’s name, serial number,
and date of manufacture.
1-9
While the monitor is receiving a video signal, press and
hold the MENU button for more than 5 seconds.
The monitor’s information box appears.
MENU
If any problem persists, call your authorized Sony dealer and give
the following information:
• Model name: SDM-M51
• Serial number
• Name and specifications of your computer and graphics board.
Specifications
This monitor is equipped with a self-diagnosis function. If there is
a problem with your monitor or computer(s), the screen will go
blank and the 1 (power) indicator will either light up green or
flash orange. If the 1 (power) indicator is lit in orange, the
computer is in power saving mode. Try pressing any key on the
keyboard or moving the mouse.
1 (power)
indicator
If the 1 (power) indicator is green
1 Turn off the 1 (POWER) switch and disconnect the
video signal cables from the monitor.
2 Turn the monitor on by pressing the 1 (POWER)
switch.
If all four color bars appear (white, red, green, blue), the monitor
is working properly. Reconnect the video input cables and check
the condition of your computer(s).
If the color bars do not appear, there is a potential monitor failure.
Inform your authorized Sony dealer of the monitor’s condition.
If the 1 (power) indicator is flashing orange
Example
INFORMATION
MODEL : SDM-M51
SER NO : 1234567
MANUFACTURED : 2000-52
Model name
Serial number
Week and year
of manufacture
20
Press the 1 (power) switch twice to turn the monitor off
and then on.
If the 1 (power) indicator lights up green, the monitor is working
properly.
If the 1 (power) indicator is still flashing, there is a potential
monitor failure. Count the number of seconds between orange
flashes of the 1 (power) indicator and inform your authorized
Sony dealer of the monitor’s condition. Be sure to note the model
name and serial number of your monitor. Also note the make and
model of your computer and graphic board.
LCD panel
Panel type: a-Si TFT Active Matrix
Picture size: 15.1 inch
Input signal format
RGB operating frequency*
Horizontal: 28 – 64 kHz
Vertical: 48 – 75 Hz
Resolution
Horizontal: Max.1024 dots
Vertical: Max.768 lines
Input signal levels
RGB video signal
0.7 Vp-p, 75 Ω, positive
SYNC signal
TTL level, 2.2 kΩ,
positive or negative
(Separate horizontal and vertical,
or composite sync)
0.3 Vp-p, 75Ω, negative
(Sync on green)
Audio output
1W×2
Headphones jack
Stereo minijack
Accepts impedance of 16 – 48 Ω
AUDIO IN jack
Stereo minijack
Accepts impedance of 47 kΩ
Accepts level 0.5 Vrms
Power requirements
100 – 240 V, 50 – 60 Hz,
0.4 – 0.2 A
DC input
DC 18 V (supplied AC adapter)
Power consumption
Max. 19 W
Max. 22 W (including AC adapter)
Operating temperature
5 – 35 ˚C
Dimensions (width/height/depth)
Display (upright):
Approx. 387 × 345 × 180 mm
(15 1/4 × 13 5/8 × 7 1/8 inches)
(with stand)
Approx. 387 × 296 × 48 mm
(15 1/4 × 11 3/4 × 1 15/16 inches)
(without stand)
Mass
Approx. 4.6 kg (10 lb 14 oz) (with
stand)
Plug & Play
DDC1/DDC2B/DDC2Bi
Accessories
See page 7.
* Recommended horizontal and vertical timing condition
• Horizontal sync width duty should be more than 4.8% of total
horizontal time or 0.8 µs, whichever is larger.
• Horizontal blanking width should be more than 2.5 µsec.
• Vertical blanking width should be more than 450 µsec.
Design and specifications are subject to change without notice.
21
GB
SDM-M51
SECTION 2
DISASSEMBLY
2-1. BEZLE ASSY AND BACK CABINET REMOVAL
1 Two screws
(+PTP 3 x 14)
2 Back cabinet
3 TFT panel
Claw
4 Bezel a'ssy
Cushion
2-1
SDM-M51
2-2. TFT PANEL AND H BOARD REMOVAL
1 Four screws
(+PVM 3 x 8)
CN801
2 TFT panel
3 H board
to CN3
to CN2
2-3. JI BOARD REMOVAL
1 Tree screws
(+PM 3 x 4)
2 Shield cover(B)
3 Tree screws
(+PM 3 x 4)
4 Insulstor
CN3
CN1
5 DC-AC inverter
CN2
2-2
SDM-M51
2-4. A BOARD AND J2 BOARD REMOVAL
1 Three screws
(+PM 3 x 4)
2 Shield cover (A)
3
4 A board
CN702
CN4
3 Three screws
(+PM 3 x 4)
CN5
CN1
CN6
CN2
5 Screw
(+PTP 3 x 6)
CN3
6 J2 board
2-3
SDM-M51
2-5.
J1 BOARD REMOVAL
3 Two screws
(+PM 3 x 4)
1 Three screws
(+PM 3 x 4)
CN906
4 J1 board
CN904
CN905
CN908
2 Two screws
2-4
SDM-M51
SECTION 3
ADJUSTMENTS
3-1. FUNCTIONAL ALIGINMENT (1)
• Procedures of how to go to service mode.
1.
2.
3.
4.
5.
6.
7.
Hold "+" and "-" key power on, SDM-M51 goes into service mode.
Press "MENU" key-----ODS display.
Press "-" key to go to second page's late icon.
Press "OK" key----service menu display.
Select one of features.
Press "MENU" key to exit OSD.
Power OFF then ON again, monitor go to normal mode.
If you would like to enter service mode again, performing the above procedures cycle.
CONFIGURATION
(N/A)
CHIPS
(N/A) COMMUNICATION
SYNC SLICE
(N/A) SHARPNESS
EXIT
OK
OK
COLOR TEMP
INITIAL EE PROM
9300K
6500K
5000K
CLEAR ETI TIME
(N/A) PRESET B/C/C
OK
(N/A) BRT
(N/A) EEPROM TEST
EXIT
EXIT
PERFORM
INITIAL EE PROM
On
Off
Note
1. N/A means "Not applied".
2. This service menu only provides both Configuration & Sync slice fuctions.
This other were used for design engineering. There is no guarantee of using those N/A functions.
3-1
SUB-BRIGHTNESS
R
G
B
SUB-CONTRAST
R
G
B
EXIT
SDM-M51
3-2. FUNCTIONAL ALIGINMENT (2)
• Equipment
3. An error message would pop up should communication fail.
A 'BREAK' icon would show up on the dialog screen. If this
happens, check the hardware setup, communication cable,
and the connection.
Computer:
• Warm up time
This paper documents the functional alignment (Used Color meter
) procedure of Sony LCD monitor SDM-M51.
PC workstation with Wndows 95 installed
PS/2 mouse is required
Software:
Capetronic engineering alignment software
tool
Color meter:
Option
Signal generator: Option
Cable:
Special RS232 interface cable
Allow 30 minutes warm up time before doing any adjustment.
• Color Adjustment
1. 9300K color adjustment
--Center adjustment-a. Click 'Color Temperature' as '9300'.
b. Apply 40% IRE white video field, primary mode.
c. Make sure 'backlight' register data is 0 (100%).
d. Click 'Refresh' .
Refer to table 1 for default data for color adjustment.
e. Adjust 'sub_brt_R' and 'sub_brt_B' to achieve color
temperature. Refer to table 2 for specifications.
f. Click 'Save this color' for a 9300K color save.
• Setup
1. Copy ECS software <ALIGN.EXE> into a new PC directory.
2. Prepare timing and pattern data for signal generator according to Sony's timing specifications.
3. Prepare timing files for <ALIGN.EXE>.
4. Connect monitor interface cable between flat panel monitor
and PC com port.
5. Connect monitor video cable to signal generator.
6. Put Topcon 50cm from the this monitor; Point it perpendicularly at the center of the display; Achieve the best focus
throught the eyepiece.
7. Enclose the this monitor and Topcon in a light-shield chamber.
8. Set up[SERVICE MODE]the this monitor and click as
'RS232C' by[COMUNICATION] of <SERVICE MENU>.
2. 5000K color adjustment
a. Click 'Color Temperature' as '5000'
b. Repeat alignment procedure as 9300 steps b - f.
3. 6500K color adjustment
a. Click 'Color Temperature' as '6500'
b. Repeat alignment procedure as 9300 steps b - f.
• Geometry Adjustment
• Download
1.
2.
3.
4.
5.
6.
7.
8.
9.
In order to enhance productivity, a software utility is provided to download default data to LCD monitor. The default
data includes color balance data and geometry timing data.
• Operation
1.
2.
3.
4.
5.
6.
Execute software <ALIGN.EXE>.
Click on 'Setup' menu.
Select 'Monitor' type as 'Sony SDM-M51'.
Select 'COM PORT' according to hardware connection.
Click <OK> to save the new setup configuration.
Quit this application and Re-enter to make the new settings
effective.
• On Screen Adjustment
1. Click on the 'Monitor' icon; an virtual monitor panel would
show up.
2. On entry, the software tires to establish a communication
link with the monitor. The monitor internal DACs are read
and shown on screen sliders. A 'CONNECT' icon would
show up on the lower left corner of the dialog screen.
3-2
Connect the personal computer which has alignment data.
Click 'Refresh' (inside Geometry Register Box).
Adjust 'Pitch' for optinum screen performance.
Adjust 'Phase' for optinum screen performance.
Adjust 'H position' to make the screen center horizontally.
Adjust 'V position' to make the screen center vertically.
Repeat steps 3-6 for best pictre performance.
Click 'Save Geomtory' to perform a user timing mode save.
Repeat step 1-7 for each of the user preset timings.
SDM-M51
Table 1: Default data for color adjustment
Color
Brightness (G)
Contrast (G)
Sub-Brt-R
Sub-Brt-B
Sub-Brt-G
Sub-Cont-R
Sub-Cont-B
Sub-Cont-G
9300K
128
75
152
162
140
75
75
75
6500K
128
75
180
154
140
75
75
75
5000K
128
75
192
122
140
75
75
75
y
298
328
358
10
Y (40% IRE)
10
10
10
3
Table 2: Specifications for Color adjustment
Color
9300
6500
5000
Tole
x
283
314
345
10
Y: Luminance measurements are in cd/m2
3-3
SDM-M51
MEMO
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
3-4
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAMS
J1
1
1
2
RED
GREEN
3
BLUE
HS IN
VS IN
13
14
D-SUB
ADC GND
ADC GND
2
3
GREEN
GREEN
3
4
ADC GND
BLUE
4
5
ADC GND
BLUE
6
ADC GND
ADC GND
6
7
HS IN
HS IN
7
10
15
5
DDC SDA
15
DDC SCL
9
DDC VCC
D902
TO
RS-232C
+5V
2
RXD
3
TXD
4
VS IN
9
DDC SDA
1
2
DDC VCC
DDC VCC
2
3
DDC SCL
DDC SCL
3
4
TXD
+5V
TXD
+5V
4
2
Y0
5
1
YI
6
RXD
RXD
6
12 X0
15
28 SDA / TXD
X 14
29 SCL / RXD
Y
CN908
1
2
3
1
TO
AC ADAPTER
20
104 H DATA 2
62
HDATA3
21
102 H DATA 3
57
SW
24
EEPROM
5
SCL 14
6
SCK
25
7
WP
3
GND
4
DC IN
SCL
6
1
7 SDA
12 X1
X1
12.0 MHz
8 SCL
/TEST
HFS
7
S807
KEY -
3
KEY +
4
KEY DOWN
5
D801
H
+5V
1 V IN
RST
OUT
100 RESET
Q3
BUFFER
3
7
PDG 5
55
141 TCLK
54
PDB 0
50
H REF
5
115
OSD H REF
V REF
10
116
OSD V REF
PDB 5
48
GND
R 0
10
R1
R 2
KEY PWR
LED AMB
9
LED GRN
38 HALF V
LED AMB
2
LED
39 HALF H
LED GRN
3
R 4
R 5
16
GND
17
GND
18
GND
19
G 0
20
G 1
21
G 2
22
GND
23
G 3
24
G 4
25
G 5
26
GND
27
GND
28
GND
29
B 0
30
B 1
31
B 2
32
GND
33
34
B 3
B 4
G
14
119
OSD DATD 1
35
B 5
R 15
120 OSD DATD 2
36
GND
H TONE 11
121 OSD DATD 3
122 OSD FSW
37
DE
38
VDD
39
VDD
40
VDD
41
VDD
FBKG 12
PDISPE 43
3.3V
76
PWR SW 19
7
R 3
15
118 OSD DATD 0
KEY UP
8
GND
14
13
PPWR
Q3
Q7,Q8
BUFFER
SW
Q6
3.3V SW
TO
LCD PANEL
F3
1.5A
113 KEY PWR
5V
GND
9
B
RST
KEY MENU
11
101 IRQ
IC6
RESET
6
10
103 H CLK
V SYNC 44
KEY AUTO
2
98 H FS
23
H CLK 22
VCLK
CN801
S801
X OUT 3
.
.
8 VCC
1
4
64
PDG 0
IC8
OSD
11 X2
SDA
5
DC IN
IC1
50Hz
+3.3V
(RV DDA)
SI
SDA 13
WP
IC4
EEPROM
AR
H DATA 0
HDATA2
99
IC7
9
7
8
11
12
105 H DATA 1
AL
GND
PDR 5
18
AUD GND
2
71
17
CN904
J901
GND
HDATA1
10
J907
V SYNC
6
13
11
PHONE
H SYNC
PVS
HDATA0
13 XI
GND
5
IC11
MICRO CONTROLER
IC3
MULTIPLEXER
DDC SDA
DCLK
3
4
66
148 V SYNC
2
73
150 H SYNC / CS
V
GND
74
PDR 0
H
1
PHS
87 BLUE
1
5
1
8
91 GREEN
44
B
CN3
CN905
CN902
GND
ADC GND
VS IN
9
G
5
ADC GND
PCLKA
95 RED
1
2
8
12
R
RED
RED
1
CN7
CN6
CN906
11
IC10
ADC/ZOOM ENGINE
A
112 KEY MENU
111 KEY UP
110 KEY DOWN
GND
109 KEY +
124 KEY -
IC2(2/2)
7
BIAS
123 KEY AUTO
IC5
AUDIO AMP
5
75
IC2(1/2)
3
1
R +
2
VC 1
OUT 1 + 16
8
VC 2
OUT 1 -
13
OUT 2 -
12
OUT 2 +
9
R-
CN2
AL
1
AUD GND
2
AR
3
6
VI 2
4
VI 1
L L +
CN5
J2
11
10
2
4
8
6
9
3
KEY MENU
4
LED AMB
5
KEY UP
6
KEY AUTO
KEY DOWN
7
9
10
11
13
3
OPL -
OPL -
14
2
OPR -
OPR -
15
1
12
16
OPR +
CN1
1
2
F1
1.5A
D3
3
SPK R -
4
SPK L+
3
SPK L -
2
SPK R -
1
SPK R +
4-1
5
D2
L+
L+
R+
R+
F2
1.5A
Q3
Q4
BUFFER
3.3V SW
+3.3V
23 V IN
VL
25 BST 3
BST 5 18
27 DH 3
DH 5 16
22
26 LX 3
LX 5 17
24 DL 3
DL 5
19
GND
1
2
1 CS 3
CS 5 15
GND
3
28 FB 3
FB 5 21
DC IN
4
ON 3
SPK L -
4
IC9
DC-DC CONVERTER
Q5
3.3V SW
CN4
DC IN
+5V
8
GND
KEY +
OPL +
7
5
2
GND
KEY -
CN702
SPK L+
SPK R +
1
KEY PWR
LED GRN
4
1
3
LED 5V
Q2
5V SW
+5V
Q1
5V SW
3
ON 5 13
L
SPEAKER
/SH ON 12
R
4-2
DC IN
GND
BKLT ADJ
GND
BKLT ON
TO
DC-AC
INVERTER
(1) Schematic Diagram of H Board
4-2. CIRCUIT BOARDS LOCATION
1
3
2
4
5
J1
A
A
SW801
SW-DPST
SW802
SW-DPST
B
H
SW803
SW-DPST
SW804
SW-DPST
1
3
2
4
1
3
2
4
1
3
2
4
1
3
2
4
1
3
2
4
1
3
2
4
1
3
2
4
KEY PWR
KEY MENU
KEY UP
KEY DOWN
C
SW805
SW-DPST
KEY PLUS
J2
D
SW806
SW-DPST
SW807
SW-DPST
DC-AC INVERTER
KEY MINUS
KEY AUTO
CN801
B11B-PH-K
GND
E
TO A BOARD
CN5
1-12pin
1
2
3
4
5
6
7
8
9
10
11
LED801
3
LED AMB
LED GRN
LED 5V
2
1
DUAL_LED_CA
F
4-3. SCHEMATIC DIAGRAMS AND PRINTED
WIRING BOARDS
GND
H
Note:
• All capacitors are in µF unless otherwise noted. (pF: µµF)
Capacitors without voltage indication are all 50 V.
• Indication of resistance, which does not have one for rating
electrical power, is as follows.
Note: The components identified by shading and mark
! are critical for safety. Replace only with part
number specified.
G
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP : 1/10 W)
• All resistors are in ohms.
• f : nonflammable resistor.
• F : fusible resistor.
•
¢ : internal component.
• p : panel designation, and adjustment for repair.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
e : earth-ground.
•
E : earth-chassis.
•
• All voltages are in V.
• Readings are taken with a 10 M digital multimeter.
• Readings are taken with a color-bar signal input.
• Voltage variations may be noted due to normal production
tolerances.
•
* : Can not be measured.
• Circled numbers are waveform references.
• s : B + bus.
• S : B – bus.
Note: Les composants identifiés per un tramé et une
marque ! sont critiques pour la sécurité. Ne les
remplacer que par une pièce portant le numéro
spécifié.
4-3
— H BOARD (Conductor Side) —
4-4
6
(2) Schematic Diagram of A( a - c ) Board
3
2
4
5
L9
3
A- a
7
Z501
8
10
9
11
12
14
13
DVDDA
1
C89
C21
C68
C69
10µF
10µF
0.1µF
0.1µF
C86
C4
C71
C70
10µF
0.1µF
0.1µF
+
2
+3.3V
3 L1 1
SVDDA
+
+
Z501 2
10µF
1
L2
+
C23
C67
C81
C30
C72
C82
C51
C52
10µF
0.1µF
0.1µF
0.1µF
0.1µF
0.1µF
0.1µF
0.1µF
C87
C5
C16
10µF
10µF
0.1µF
C91
C35
C37
C49
C80
C79
C8
C31
C32
C36
C42
C17
C83
10µF
0.1µF
0.1µF
0.1µF
0.1µF
0.1µF
10µF
0.1µF
0.1µF
0.1µF
0.1µF
0.1µF
L8
Z501
+3.3V
3
2
RVDDA
1
+
Z501
+
3
C90
+
A
6
+
1
10µF
2
++
L11
C88
+
B
VDDA
+
+
Z501
10µF
2
1 TP3
1 TP5
1 TP8
10µF
150
C40
D
R54
R
R55
R
R70
2.2K
R71
#
94
90
86
R57
150
C46
0.01µF
R69
150
C48
0.01µF
ADC_GNDA
Sync GRN
H sync IN
TP16
GND
R60
TP17
100
V sync IN
R59
100
1
C55
100pF
C56
100pF
E
4 H sync_MCU
H
4 V sync_MCU
V
RVDDA
1
+5V
GND
L19
Z102
OSC1
50MHz
4
VCC
2
C59
0.1µF
1
XOUT 3
L6
BMK400
1
GND
L4
STC104B
3
1
SB
IC8
MTV130P-10
C22
0.1µF
9 VDD2
2
4 VDD1
C25 16
VSS2
0.1µF
1 VSS1
C101
2
F
33pF
HREF 5
VREF 10
OSD_CLK 2
R
G
B
HTONE
3 NC
R27
100
13
14
15
11
12
FBKG
GND
PLL_GDNA
GND
SDA 7
SCL 8
6 SSB
G
HDATA0
HDATA1
HDATA2
HDATA3
MFB7
MFB8
MFB9
MFB0
MFB1
MFB2
MFB3
MFB4
MFB5
MFB6
MFB7
MFB8
MFB9
MFB10
MFB11
2
4
5
59
60
83
97
130
135
145
147
152
156
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
NC
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
150
148
HSYNC/CS
VSYNC
141
142
TCLK
XTAL
153
154
155
157
159
160
3
ST1_TM1
ST1_TM2
SCAN_IN1
SCAN_IN2
SCAN_OUT1
SCAN_OUT2
PSCAN
115
116
117
118
119
120
121
122
OSD_HREF
OSD_VREF
OSD_CLK
OSD_DATA0
OSD_DATA1
OSD_DATA2
OSD_DATA3
OSD_FSW
98
103
99
100
101
HFS
HCLK
HDATA
RESETn
IRQ
113
112
111
110
109
107
106
105
104
102
124
123
MFB0
MFB1
MFB2
MFB3
MFB4
MFB5
MFB6
MFB7
MFB8
MFB9
MFB10
MFB11
MFB[0_11]
2 SW[0-6]
H
SW0 R52
R66
10K
Z102
R65
10K
R63
10K
R62
10K
108
148
12
33
40
65
RVDD1
RVDD2
CVDD1
RVDD3
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
PD9
PD10
PD11
PD12
PD13
PD14
PD15
PD16
PD17
PD18
PD19
PD20
PD21
PD22
PD23
PD24
PD25
PD26
PD27
PD28
PD29
PD30
PD31
PD32
PD33
PD34
PD35
PD36
PD37
PD38
PD39
PD40
PD41
PD42
PD43
PD44
PD45
PD46
PD47
71
70
69
68
67
66
64
63
62
57
56
55
54
53
52
51
50
48
47
46
42
39
38
37
36
35
34
32
31
29
28
27
26
25
24
23
22
20
19
17
16
15
14
13
10
9
7
6
PCLKA
PCLKB
PDISPE
44
45
43
PVS
PHS
PPWR
PBIAS
ZDR0
ZDR1
ZDR2
ZDR3
ZDR4
ZDR5
ZDG0
ZDG1
ZDG2
ZDG3
ZDG4
ZDG5
ZDB0
ZDB1
ZDB2
ZDB3
ZDB4
ZDB5
3
2
1
PDR0
PDR1
PDR2
PDR3
PDR0
PDR1
PDR2
PDR3
Z121
4
PDR4
PDR4
PDR5
PDR0
RP2
5
6
7
8
3
2
1
PDR5
PDR0
RP3
5
6
7
8
Z121
4
3
2
1
PDG1
PDG2
PDG3
PDG4
RP4
5
6
7
8
Z121
4
PDG5
3
PDB0
2
1
PDB1
RP5
5
6
7
8
Z121
4
3
2
4
GND
22
R74
22
CP3
MFB0
SW1 R51
Z10Z key menu
MFB1
SW2 R50
Z102 key up
MFB2
PDB[0.5]
PDG[0.5]
PDR[0.5]
LCD_ CLK
LCD_ HS
CN7
DF9-41S-1V
C84
22pF
SW4 R47
GND
C58
100pF
PDB0
PDB2
PDB3
PDB5
LCD DE
GND
C57
100pF
GND
GDN
GDN
Vsync
GDN
R0
R2
R3
R5
GDN
G0
G2
G3
G5
GDN
B0
B2
B3
B5
DE
VDD
VDD
DCLK
Hsync
GDN
GDN
R1
GDN
R4
GDN
GDN
G1
GDN
G4
GDN
GDN
B1
GDN
B4
GDN
VDD
VDD
PLL_GNDA
I
R80
4.7K
MFB10
+3.3V
R77
100K
Q6
S12304
ab5
ab4
MFB11
3
Q8
MMBT3904
ab8 ab9
ab10
ab10
ac1
4-5
GND
L16
STC104B
2
3
GND
3
F3
1.5A
1
Q7
MMBT3904
1
R82
270K
C54
0.1µF
R98
47K
C50
100µF
1
GND
GND
ab7
ab6
PDB4
2
R78
4.7K
GDN
ab3
PDB1
1
R76
100K
2
C34
1000pF
ab1 ab2
PDG4
GND
MFB4
Z102 key auto
CN7
TO LCD
PDG1
+
SW6 R48
PDR4
3
ADC_GNDA
R79
10K
Z102 key minus
PDR1
R89
#
2
SW5 R46
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
+18V
R90
10K
MFB3
Z102 key plus
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
PDG0
PDG2
PDG3
PDG5
+5V
0Z102 key down
PDB0
PDB2
PDB3
PDB4
PDB5
GND
SW3 R49
22pF
MFB5
MFB6
R64
10K
CP4
22pF
PDB1
GND
76
75
22pF
PDG1
PDG2
PDG3
PDG4
22
R75
CP5
22pF
PDR5
PDR4
PDR3
PDR2
PDR0
PDR2
PDR3
PDR5
73
74
7
6
5
CP2
LCD VS
R96
22pF
8
2
3
4
L15
BMK400
1
3
2
C85
33pF
R97
33
R113
100
93
89
85
82
81
80
78
4 PWR_SW
R67
10K
CVDD4
SYN_VDD
REDGREENBLUE-
+3.3V
R68
10K
11
21
58
0.01µF
+5V
ac1
ac1
RED+
GREEN+
BLUE+
CVSS4
DVSS
SVSS
SYN_VSS
SRVSS2
R45
95
91
87
1
CP1
Z121
4
RP1
5
6
7
8
114
126
140
151
158
R42
75
0.01µF
CVSS1
RVSS1
SRVSS1
RVSS2
CVSS2
RVSS3
RVSS4
CVSS3
R43
75
C47
1
8
18
30
41
49
61
72
R44
75
150
SUB_SGNDA
SUB_DGNDA
SUB_RGNDA
R61
SRVDD1
SRVDD2
CVDD2
0.01µF
125
139
C41
DVDD
SVDD
150
B IN
79
77
R56
B GND
133
132
146
G GND
ADC_VDD1
ADC_VDD2
0.01µF
143
137
136
129
128
C38
G IN
PLL_RVDDA
DAC_SVDDA
PLL_SVDDA
PLL_DVDDA
DAC_DVDDA
150
ADC_RVDDA
ADC_GVDDA
ADC_BVDDA
ADC_VDDA
TO J1 BOARD
CN906
C
R39
R GND
DAC_DGNDA
PLL_DGNDA
PLL_SGNDA
DAC_SGNDA
PLL_RGNDA
R IN
1
2
3
4
5
6
7
8
9
IC10
GMZAN1
ADC_GNDA
127
131
134
138
144
GND
ADC_RGNDA
ADC_GGNDA
ADC_BGNDA
ADC_GNDA
SUB_GNDA
ADC_CND1
ADC_GND2
PLL_GNDA
96
92
88
84
GND
CN6
B9B-PH-K
ac2
ac2
4-6
1
A
3
2
ab3
ab1 ab2
ab5
ab4
4
5
6
7
8
10
9
11
12
14
13
ab7
ab6
ab8 ab9
ab10
+5V
+5V
+5V
IC6
M51951B
+5V
R15
15K
RST_OUT
GND
VIN
TP6
bc11
R21
10K
R87
4.7K
R19
4.7K
R118
4.7K
R34
4.7K
1
R95
470
R94
480
bc6
RESET
1
B
3
2
R20
10K
3
2
RESETn
C66
0.1µF
Q3
MMBT3901
1
TP18
GND
GND
1
R31
0
LED_GRN2
R30
0
LED_AMB2
CN2
B3B-PH-K
1
2
3
TP19
1
C105
1000pF
AUD_GND
SOG SELn
C
V
V sync_MGU5
H sync_MGU5
H
H Slice
+5V
TP4
6
5
4
3
2
1
44
43
42
41
40
DP/NC
DM/NC
V33CAP/NC
P5.0/DA0
P5.1/DA1
P5.2/DA2
VSYNC
HSYNC
P5.3/DA3
P5.4/DA4
P5.5/DA5
XTAL1
11.0592MHz
TP7
C29
30pF GND
1
1
1
+5V
C20
0.1µF
R41
4.7K
R19
4.7K
R24
4.7K
C63
0.1µF
IC5
TDA7053A
R15
5.6K
DA8/HALFH
DA9/HALFV
P4.1/HBLANK
P4.0/VBLANK
DA7/HCLAMP
P5.6/DA
P2.7/DA13
P2.6/DA12
P2.5/DA11
P2.4/DA10
P3.0/HSCL/RXD
39
38
37
36
35
34
33
32
31
30
29
1
2
3
4
C62
0.47µF
C13
2.2µF
GND
6
7
8
C64
0.47µF
NC
VC1
NC
VI1
VI2
SGND
VC2
C12
100µF
5
OUT1+
NC
PGND1
OUT1OUT2NC
PGND2
OUT2+
16
15
14
13
12
11
10
9
AUD_GND
bc2
bc3
R130
#
bc5
R85
4.7K
R86
4.7K
R129
#
bc4
TP10
TP9
1
C130
#
1
C114
#
+5V
18
19
20
21
22
23
24
25
26
27
28
R117
#
E
R14
4.7K
VP
RST
VDD
R2.3/AD3
VSS
X2(o/p)
X1(i/p)
P3.4/ISDA/T0
P3.5/ISL/T1
P4.2/STOUT
P2.2/AD2
P1.0
P1.1
P3.2/INTO
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P2.1/AD1
P2.2/AD0
P3.1/HSDA/TXD
D
7
8
9
10
11
12
13
14
15
16
17
C28
30pF
+5V
+
C27
0.1µF
2
C106
1000pF
+3.3V
IC11
MTV212M
GND
AUD_GND
R7
1K
+3.3V
GND
R114
4.7K
R25
4.7K
R35
4.7K
R36
4.7K
R37
4.7K
R38
4.7K
IC7
24C16
1 A0
2 A1
3 A2
4 VSS
R40
4.7K
R3
15K
+5V
bc1
8
7
6
5
VCC
WP
SCK
SI
+5V
R122
10K
R123
1K
+5V
R121
10K
5 DATA[0-3]
F
HDATA0
HDATA1
HDATA2
HDATA3
R116
Q12
MMBT3904
H sync IN
Sync GRN
G
2
D6
3.3V
R128
150
1
C94
10µF
R99
Z102
R103
2.7K
+
1
R105
2.2K
1
R106
1K
R102
300k
1
IC14A
LM358
IC12A
74F14 GND
2
R84
4.7K
R102
300k
C93
0.1µF
I
3
3
R107
100
1
2
IC13A
74F125
3
C99
0.1µF
C100
0.1µF
5
6
11
2
1
SDA 2Bi
Z0
Z1
5
3
VCC INH
A
VEE
B
GND
C
TXD
SDA 2Bi
6
11
10
9
CN3
B6B-PH-K
1
2
3
4
5
6
R12
4.7K
+5V
DDC_VC
TXD
RXD
R8
10K
10
DDC SDA
4 IC13B
74F125
R11
10K
IC12E
74F14
R9
R10
33
5
VCC /TEST
NC
SDA
/WP
1
2
3
6
SCL
7
GND
GDN
33
C7
220pF
C19
0.1µF
IC12C
74F14
1
GND
GND
V sync-IN
9
IC12D
74F14
8
GND
GND
GND
IC12F
74F14
13
12
A- b
J
Schematic diagram
Schematic diagram
- a board
VCLK
6
3
Q9
RN1203
Ò A
2
C15
0.1µF 1
IC4
24C21
DDC SCL
C6
220pF
SOG SELn 2
ADC_GNDA
SCL 2Bi
Y0
Y1
8
4
5
12 RXD
13 SCL 2Bi
+18V
TO J1 BOARD
CN905
1
R126
0
H Slice
7
8
X0
X1
C98
2.2µF
GND
ADC_GNDA
Q10
MMBT3904
2
Z
GND
GND
IC12B
74F14
4
R100
100K
R101
100K
C95
0.1µF
C60
0.1µF
2
GND
ADC_GNDA
IC15A
LM393M
-
R109
#
R112
1K
3
4
R110
0
3 +
2
-
4
R111
15K
8
2.7K
2
C92
10µF
H
C97
0.1µF
1
1
2
Q11
MMBT3906
2
X
Y
16
R125
470
R104
14
15
+5V
R108 470
R127
0
3
D4
D5
1N4148 1N4148
#
+5V
+3.3V
+5V
IC3
74HC4053
0
R115
C3
2.2µF
R124
1K
4-7
A
- b board
l
4-8
D1
5.1V
1
3
2
4
5
6
7
8
10
9
11
12
A
bc1
ac2
L5
27µH
C61
0.1µF
C11
100µF
GND
F2
1.5A
1
D3
1N4148
2
1
R93
0
C74
10µF
TP11
D2
1N4148
1
2
GND
8
L12
Z501
R58
0.045R
L13
15µH
1
5
6
C44
47µF
+
4
GND
TP15
23
25
27
GND
2
+
C43
47µF
7
Q2
SI4808
26
C39
0.1µF
24
V+
BST3
DH3
VL
BST5
DH5
LX3
LX5
DL3
DL5
22
18
16
C18
0.1µF
Q1
SI4808
GND
2
17
1
5
6
19
4
TP2
PA_GND
L3
27µH
GND
+5V
R13
0.045R
L10
Z501
C9
47µF
GND
GND
1
28
5V_ON
C77
0.01µF
R91
0
R92
47K
2
CS2
FB3
CS5
FB5
GND
TP1
SS3
SS5
15
21
1
14
GND
PA_GND
3
13
12
11
9
10
R88
0
C78
0.1µF
C10
47µF
GND
1
GND
1
3
3
E
C24
22µF
7
8
IC9
SI786
C76
0.1µF
+
C33
22µF
+3.3V
1
5V_ON
C25
100µF
GND
D
L18
Z102
+18V
+
+
C75
0.1µF
L14
3µH
TO DC-AC INVERTER
+
C
1
2
3
4
5
L17
Z102
GND
TP11
CN1
B5B-PHK
L7
Z501
+
TO J1 BOARD
CN904
B
F1
1.5A
1
2
3
4
+
CN4
B4B-EH
F
ON3
ON5
/SHDN
SYNC
GND
REF
VH
D1
Q1
D2
Q2
PGND
C65
0.01µF
6
4
8
5
7
20
PA_GND
GND
bc2
bc3
TP13
C73
1µF
bc4
TP14
R81
0
R1
0
bc5
1
bc6
1
GND
LDE_5V
LDE_GRN
LDE_AMB
G
PA_GND
GND
CHAS_GND
GND
R4
0
SPK_R+
SPK_R-
SPK_L+
SPK_L-
CHAS_GND
R88
0
2.Micro Controller
GND
CN5
B16B-PHDSS
H
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
R29
0
I
GND
GND
CHAS_GND
1-12pin
TO H BOARD
CN801
13-16pin
TO J2 BOARD
CN702
SW5
SW4
SW3
SW2
SW1
SW0
SW6
R28
0
CHAS_GND
A- C
GND
ac1
J
4-9
4-10
— A BOARD (Conductor Side) —
1
3
2
4
5
6
7
A
L901
2.5T
CN901
EIAJ-5
B
+
D901
SB-540
CN904
S4B-EH
+
C902
220µF
C901
0.1µ
1
2
3
4
L902
3µH
C
CN906
S9B-PH-K
GND
RED
1
2
3
4
5
6
7
8
9
GREEN
BLUE
D903
#
D904
#
1
6
2
7
3
8
4
9
5
10
D905
#
D
CN903
RGB Connector 11 DB15
12
DDCSDA
13
HS IN
14
VS IN
DDCSCL
15
E
D906
HZ5C1
D909
HZ5C1
CN905
S6B-PH-K
TXD
RXC
+5V
TXD
+5V
RXD
D910
HZ5C1
MINI_DIN_4
CN907
F
D908
HZ5C1
CN902
4
3
2
1
PHONEJACK
STEREO
3
2
1
C903
1000pF
D911
HZ5C1
CN908
S3B-PH-K
AL
AR
AUD GND
1
2
3
TO
A BOARD
CN2
GND
J1
C904
1000pF
AUD GND
G
CN701
PHONEJACK
STEREO SW
C701
10µF
+
R701
150
+
R702
150
H
CN702
B5BPH-PH-K
C702
10µF
OPL+
OPL-
OPR-
OPR+
5
4
3
2
1
Input From
M/B`s Amp
CN703
S4B-PH-K
I
GND
J2
Schematic diagram
Schematic diagram
Ò A
- c board
4-11
J1 J2
board
l
TO
A BOARD
CN6
ADC_GND
D907
HZ5C1
AUD GND
D902
1N4148
TO
A BOARD
CN4
4-12
SPK
SPK
SPK
SPK
L+
L-
R-
R+
4
3
2
1
Speakers
1
2
3
4
5
6
TO
A BOARD
CN3
(j1)(j2)
— J1 BOARD (Conductor Side) —
— J2 BOARD (Conductor Side) —
4-13
4-4. SEMICONDUCTORS
GMZAN1
M5195BML
DTC124EA-T106
RLS-4148
RLZ5.1B
CATHODE
OUT
IN
VIN
GND
VOUT
n
GND
ANODE
1
TOP VIEW
160 pin QFP
M24C16-MN6T
LM358D
LM393D
24LC21AT/SN
TDA7053A
CATHODE
n
n
1
n
SB540
SI4808DY
TOP VIEW
1
ANODE
1
16 pin DIP
8 pin CHIP
TOP VIEW
8 pin SOP
MC74F14M
MC74F125M
SI786LG-T1
SI2304DS-T
SST3904T
SST3906T
n
n
C
B
1
1
E
TOP VIEW
TOP VIEW
14pin SOP
28 pin SOP
MC74HC4053F
MTV130
n
1
TOP VIEW
16 pin SOP
4-14
SDM-M51
SECTION 5
EXPLODED VIEWS
NOTE:
• Items with no part number and no
description are not stocked because they
are seldom required for routine service.
• The construction parts of an assembled
part are indicated with a collation number
in the remark column.
• Items marked " * " are not stocked since
they are seldom required for routine
service. Some delay should be
anticipated when ordering these items.
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque ¡ sont critiques pour la
sécurité. Ne les remplacer que par une
pièce portant le numéro spécifié.
5-1. CHASSIS
12
3
5
7
4
2
8
1
10
11
6
9
REF.NO. PART NO.
DESCRIPTION
1
2
3
4
5
1-476-422-11 INVERTER, DC-AC
1-803-808-11 PANEL, LCD
CABINET, BACK ASSY
4-079-642-01 COVER, REAR
A-1272-202-A A MOUNT
6
A-1372-905-A H MOUNT
REMARK
REF.NO. PART NO.
241-SM15011
245-151LG01
422-S-0305010
422-0145010
209-5010010
209-5010030
5-1
DESCRIPTION
REMARK
7
8
9
10
A-1388-293-A J1 MOUNT
A-1388-294-A J2 MOUNT
X-4038-369-1 BEZEL ASSY
1-529-902-11 SPEAKER (20X40MM)
209-5010020
209-5010040
422-S-0105010
KSI40X20
11
12
X-4038-370-1 STAND ASSY
* 4-079-418-11 LABEL, INFORMATION
422-S-0205010
6100605011
SDM-M51
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
5-2. PACKING MATERIALS
Les composants identifiés par une
marque ¡ sont critiques pour la
sécurité. Ne les remplacer que par une
pièce portant le numéro spécifié.
54 55 56 57 58 59 60 61
52
53
51
REF.NO. PART NO.
51
52
53
54
55
56
* 4-079-078-01
4-079-619-01
4-079-620-01
1-476-397-11
1-757-371-11
DESCRIPTION
INDIVIDUAL CARTON
CUSHION (L)
CUSHION (R)
ADAPTOR, AC
CABLE ASSY (HD15X2)
REMARK
REF.NO. PART NO.
DESCRIPTION
REMARK
601-9115010
404-9135010
404-9145010
201-6018010
186-5010001
57
58
58
59
1-772-979-11 DISK, INFORMATION (CD-ROM)
617-0105010
¡ 1-765-719-21 CORD SET, POWER (AEP)
¡ 1-765-720-21 CORD SET, POWER (U/C)
1-778-967-21 ADAPTOR, CONVERSION (U/C)
1-757-372-11 CORD, CONNECTION (WITH PLUG)
1865010002
60
61
¡ 1-792-179-11 CONNECTOR, D SUB (15P CHANGER)
4-079-344-11 MANUAL, INSTRUCTION
6120105011
(AEP) 204-TRYG301
5-2
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
REF.NO. PART NO.
NOTE:
SECTION 6
(a)
ELECTRICAL PARTS LIST
DESCRIPTION
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque ¡ sont critiques pour la
sécurité. Ne les remplacer que par une
pièce portant le numéro spécifié.
When indicating parts by reference
number, please include the board name.
REF.NO. PART NO.
SDM-M51
Les composants identifiés par une
marque ¡ sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
REMARK identified
REF.NO.byPART
The components
[ in NO.
this
manual have been carefully factoryselected for each set in order to satisfy
regulations regarding X-ray radiation.
Should replacement be required, replace
only with the value originally used.
DESCRIPTION
RESISTORS
• All resistors are in ohms
• F : nonflammable
REMARK
• Items marked " * " are not stocked since
they are seldom required for routine
service. Some delay should be
anticipated when ordering these items.
• All variable and adjustable resistors have
characteristic curve B, unless otherwise • CAPACITORS
MF : µF
noted.
• COILS
UH : µH
DESCRIPTION
REMARK
REF.NO. PART NO.
A MOUNT
************
<CAPACITOR>
C003
C004
C005
C006
C007
1-164-505-11
1-117-370-11
1-117-370-11
1-164-230-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2UF
10UF
10UF
220PF
220PF
16V
10V
10V
50V
50V
122-CY225Z16TX
122-CY106Z10TW
122-CY106Z10TW
122-CC221J50TV
122-CC221J50TV
C008
C009
C010
C011
C012
1-117-370-11
1-126-513-11
1-126-513-11
1-128-126-11
1-117-681-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT CHIP
10UF
47UF
47UF
100UF
100UF
10V 122-CY106Z10TW
6.3V 164-RE470M06
6.3V 164-RE470M06
25V 162-RV3101M25
16V 162-RV2101M16
C013
C015
C016
C017
C018
1-164-505-11
1-131-992-11
1-131-992-11
1-131-992-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2UF
100000PF
100000PF
100000PF
0.1UF
16V
35V
35V
35V
50V
122-CY225Z16TX
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z50TX
C019
C020
C021
C022
C023
1-131-992-11
1-115-339-11
1-117-370-11
1-131-992-11
1-117-370-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100000PF
0.1UF
10UF
100000PF
10UF
35V
50V
10V
35V
10V
122-CY104Z25TV
122-CY104Z50TX
122-CY106Z10TW
122-CY104Z25TV
122-CY106Z10TW
C024
C025
C026
C027
C028
1-126-796-11
1-131-992-11
1-128-126-11
1-131-992-11
1-164-457-51
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
22UF
100000PF
100UF
100000PF
30PF
25V
164-RE220M20
35V 122-CY104Z25TV
25V 162-RV3101M25
35V 122-CY104Z25TV
50V 122-CC300J50TV
C029
C030
C031
C032
C033
1-164-457-51
1-131-992-11
1-131-992-11
1-131-992-11
1-126-796-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
30PF
100000PF
100000PF
100000PF
22UF
50V
35V
35V
35V
25V
122-CC300J50TV
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
164-RE220M20
C034
C035
C036
C037
C038
1-115-416-11
1-117-370-11
1-131-992-11
1-131-992-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1000PF
10UF
100000PF
100000PF
0.01UF
25V
10V
35V
35V
25V
122-CX102K50TV
122-CY106Z10TW
122-CY104Z25TV
122-CY104Z25TV
122-CX103K50TV
C039
C040
C041
C042
1-115-339-11
1-162-970-11
1-162-970-11
1-131-992-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1UF
0.01UF
0.01UF
100000PF
50V
25V
25V
35V
122-CY104Z50TX
122-CX103K50TV
122-CX103K50TV
122-CY104Z25TV
6-1
DESCRIPTION
REMARK
C043
1-126-513-11 ELECT
47UF
6.3V
164-RE470M06
C044
C046
C047
C048
C049
1-126-513-11
1-162-970-11
1-162-970-11
1-162-970-11
1-131-992-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47UF
0.01UF
0.01UF
0.01UF
100000PF
6.3V 164-RE470M06
25V 122-CX103K50TV
25V 122-CX103K50TV
25V 122-CX103K50TV
35V 122-CY104Z25TV
C050
C051
C052
C054
C055
1-117-681-11
1-131-992-11
1-131-992-11
1-131-992-11
1-162-927-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100UF
100000PF
100000PF
100000PF
100PF
16V
35V
35V
35V
50V
162-RV2101M16
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
122-CC101J50TV
C056
C057
C058
C059
C060
1-162-927-11
1-162-927-11
1-162-927-11
1-131-992-11
1-131-992-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100000PF
100000PF
50V
50V
50V
35V
35V
122-CC101J50TV
122-CC220J50TV
122-CC220J50TV
122-CY104Z25TV
122-CY104Z25TV
C061
C062
C063
C064
C065
1-115-339-11
1-164-005-11
1-131-992-11
1-164-005-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1UF
0.47UF
100000PF
0.47UF
0.01UF
50V
25V
35V
25V
25V
122-CY104Z50TX
122-CY474Z50TX
122-CY104Z25TV
122-CY474Z50TX
122-CX103K50TV
C066
C067
C068
C069
C070
1-131-992-11
1-131-992-11
1-131-992-11
1-131-992-11
1-131-992-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100000PF
100000PF
100000PF
100000PF
100000PF
35V
35V
35V
35V
35V
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
C071
C072
C073
C074
C075
1-131-992-11
1-131-992-11
1-164-346-11
1-117-370-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100000PF
100000PF
1UF
10UF
0.1UF
35V
35V
16V
10V
50V
122-CY104Z25TV
122-CY104Z25TV
122-CY105Z25TX
122-CY106Z10TW
122-CY104Z50TX
C076
C077
C078
C079
C080
1-115-339-11
1-162-970-11
1-131-992-11
1-131-992-11
1-131-992-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1UF
0.01UF
100000PF
100000PF
100000PF
50V
25V
35V
35V
35V
122-CY104Z50TX
122-CX103K50TV
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
C081
C082
C083
C084
C085
1-131-992-11
1-131-992-11
1-131-992-11
1-162-919-11
1-162-921-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100000PF
100000PF
100000PF
22PF
33PF
35V
35V
35V
50V
50V
122-CY104Z25TV
122-CY104Z25TV
122-CY104Z25TV
122-CC220J50TV
122-CC330J50TV
C086
1-117-370-11 CERAMIC CHIP 10UF
10V 122-CY106Z10TW
SDM-M51
Les composants identifiés par une
marque ¡ sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
(a)
REF.NO. PART NO.
DESCRIPTION
REMARK
REF.NO. PART NO.
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
DESCRIPTION
C087
C088
C089
C090
1-117-370-11
1-117-370-11
1-117-370-11
1-117-370-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10UF
10UF
10UF
10UF
10V
10V
10V
10V
122-CY106Z10TW
122-CY106Z10TW
122-CY106Z10TW
122-CY106Z10TW
IC009
IC010
IC011
IC012
8-759-541-69
8-759-712-44
8-759-712-43
8-759-033-07
C091
C092
C093
C094
C095
1-117-370-11
1-117-370-11
1-164-346-11
1-164-346-11
1-131-992-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10UF
10UF
1UF
1UF
100000PF
10V
10V
16V
16V
35V
122-CY106Z10TW
122-CY106Z10TW
122-CY105Z25TX
122-CY105Z25TX
122-CY104Z25TV
IC013
IC014
IC015
8-759-033-19 IC MC74F125M
8-759-467-94 IC LM358D
8-759-510-72 IC LM393D
C097
C098
C099
C100
C101
1-131-992-11
1-164-505-11
1-131-992-11
1-131-992-11
1-162-921-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100000PF
2.2UF
100000PF
100000PF
33PF
35V
16V
35V
35V
50V
122-CY104Z25TV
122-CY225Z16TX
122-CY104Z25TV
122-CY104Z25TV
122-CC330J50TV
C102
C105
C106
1-162-915-11 CERAMIC CHIP 10PF
1-115-416-11 CERAMIC CHIP 1000PF
1-115-416-11 CERAMIC CHIP 1000PF
REMARK
IC SI786LG-T1
IC GMZAN1
IC MTV212M
IC MC74F14M
160-SI786CG
160-00ZAN1T
610-5010V03
160-F0140T
160-F1250T
160-035800T
160-039300T
<COIL>
50V 122-CC100J50TV
25V 122-CX102K50TV
25V 122-CX102K50TV
L001
L002
L003
L004
L005
1-469-977-11 INDUCTOR 0UH
1-469-977-11 INDUCTOR 0UH
1-469-974-11 INDUCTOR 27UH
1-469-974-11 INDUCTOR 27UH
143-NG3216501
143-NG3216501
141-3L105270
280-STC104B
141-3L105270
L006
L007
L008
L009
1-469-976-11
1-469-977-11
1-469-977-11
1-469-977-11
INDUCTOR 0UH
INDUCTOR 0UH
INDUCTOR 0UH
INDUCTOR 0UH
280-NGBMK400
143-NG3216501
143-NG3216501
143-NG3216501
INDUCTOR 0UH
INDUCTOR 0UH
INDUCTOR 0UH
INDUCTOR 15UH
143-NG3216501
143-NG3216501
143-NG3216501
<#########>
CP001
CP002
CP003
CP004
CP005
L010
1-469-977-11
L011
1-469-977-11
L012
1-469-977-11
L013
1-469-975-11
141-3L105150
L014
1-469-978-11
137-010220T
137-010220T
137-010220T
137-010220T
137-010220T
<DIODE>
D001
D002
D003
D004
D005
1-807-635-11
8-719-976-19
8-719-976-19
8-719-976-19
8-719-976-19
DIODE RLZ5.1B
DIODE RLS-4148
DIODE RLS-4148
DIODE RLS-4148
DIODE RLS-4148
D006
8-719-010-19 DIODE UZ-3.3BSA
150-RLZ5V1B
151-RLS4148
151-RLS4148
151-RLS4148
151-RLS4148
150-RLZ3V3B
L015
L016
L017
L018
L019
143-3L350908
1-469-976-11 INDUCTOR 0UH
280-NGBMK400
280-STC104B
281-NG2012102
281-NG2012102
281-NG2012102
1-469-973-11 INDUCTOR 0UH
1-469-973-11 INDUCTOR 0UH
1-469-973-11 INDUCTOR 0UH
<OSCILLATOR>
OSC1
<FUSE>
F001
F002
F003
INDUCTOR 0UH
1-795-092-11 OSCILLATOR, CRYSTAL
131-50000031
<TRANSISTOR>
1-576-491-11 FUSE
1-576-491-11 FUSE
1-576-491-11 FUSE
147-BLMQ015
147-BLMQ015
147-BLMQ015
Q001
Q002
Q003
Q006
Q007
8-729-054-62
8-729-054-62
8-729-054-61
8-729-044-58
8-729-054-61
TRANSISTOR SI4808DY
TRANSISTOR SI4808DY
TRANSISTOR SST3904T
TRANSISTOR SI2304DS-T1
TRANSISTOR SST3904T
160-SI4808DY
160-SI4808DY
170-SST3904
160-SI2304DS
170-SST3904
Q008
Q009
Q010
Q011
Q012
8-729-054-61
8-729-029-06
8-729-054-61
8-729-054-60
8-729-054-61
TRANSISTOR SST3904T
TRANSISTOR DTC124EUA-T106
TRANSISTOR SST3904T
TRANSISTOR SST3906T
TRANSISTOR SST3904T
170-SST3904
170-C124EUA
170-SST3904
170-SST3906
170-SST3904
<#########>
FBA1
FBA2
FBA3
FBA4
FBA5
282-1206A4Z121
282-1206A4Z121
282-1206A4Z121
282-1206A4Z121
282-1206A4Z121
<RESISTOR>
<IC>
IC003
IC004
IC005
IC006
IC007
8-759-011-65
8-759-661-55
8-759-478-64
8-759-634-77
8-759-527-77
IC MC74HC4053F
IC 24LC21AT/SN
IC TDA7053A
IC M51951BML
IC M24C16-MN6T
IC008
8-759-712-45 IC MTV130
160-HC4053T
160-024021T
160-07053A0
160-051951T
160-024016T
160-MTV130T
6-2
R001
R003
R004
R007
R008
1-216-295-00
1-216-835-11
1-216-295-00
1-216-821-11
1-216-833-11
SHORT
RES-CHIP
SHORT
METAL CHIP
METAL CHIP
R009
R010
1-216-803-11 RES-CHIP
1-216-803-11 RES-CHIP
0
15K
0
1K
10K
100-CR00JT10
1/16W 100-C153JT16
100-CR00JT10
1/16W 100-C102JT16
1/16W 100-C103JT16
33
33
1/16W 100-C330JT16
1/16W 100-C330JT16
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
REF.NO. PART NO.
SDM-M51
Les composants identifiés par une
marque ¡ sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DESCRIPTION
REMARK
(a)(h)
REF.NO. PART NO.
R011
R012
R013
1-216-833-11 METAL CHIP
1-216-829-11 METAL CHIP
10K
4.7K
1/16W 100-C103JT16
1/16W 100-C472JT16
100-C457JT08
R014
R015
R019
R020
R021
1-216-829-11
1-216-830-11
1-216-829-11
1-216-833-11
1-216-833-11
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
5.6K
4.7K
10K
10K
1/16W
1/16W
1/16W
1/16W
1/16W
R024
R025
R027
R030
R031
1-216-829-11
1-216-829-11
1-216-809-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
SHORT
4.7K
4.7K
100
0
0
1/16W 100-C472JT16
1/16W 100-C472JT16
1/16W 100-C101JT16
100-CR00JT16
100-CR00JT16
R034
R035
R036
R037
R038
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
4.7K
4.7K
4.7K
1/16W
1/16W
1/16W
1/16W
1/16W
100-C472JT16
100-C472JT16
100-C472JT16
100-C472JT16
100-C472JT16
R039
R040
R041
R042
R043
1-216-811-11
1-216-829-11
1-216-829-11
1-216-624-11
1-216-624-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150
4.7K
4.7K
75
75
1/16W
1/16W
1/16W
1/10W
1/10W
100-C151JT16
100-C472JT16
100-C472JT16
100-C750JT10
100-C750JT10
R044
R045
R046
R047
R048
1-216-624-11
1-216-811-11
1-469-973-11
1-469-973-11
1-469-973-11
METAL CHIP
75
RES-CHIP
150
INDUCTOR 0UH
INDUCTOR 0UH
INDUCTOR 0UH
1/10W 100-C750JT10
1/16W 100-C151JT16
281-NG2012102
281-NG2012102
281-NG2012102
R049
R050
R051
R052
R056
1-469-973-11
1-469-973-11
1-469-973-11
1-469-973-11
1-216-811-11
INDUCTOR 0UH
INDUCTOR 0UH
INDUCTOR 0UH
INDUCTOR 0UH
RES-CHIP
150
281-NG2012102
281-NG2012102
281-NG2012102
281-NG2012102
1/16W 100-C151JT16
R057
R058
R059
R060
R061
1-216-811-11 RES-CHIP
150
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-811-11 RES-CHIP
100
100
150
1/16W 100-C151JT16
100-C457JT08
1/16W 100-C101JT16
1/16W 100-C101JT16
1/16W 100-C151JT16
R062
R063
R064
R065
R066
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
1/16W
1/16W
1/16W
1/16W
1/16W
100-C103JT16
100-C103JT16
100-C103JT16
100-C103JT16
100-C103JT16
R067
R068
R069
R070
R074
1-216-833-11
1-216-833-11
1-216-811-11
1-216-659-11
1-216-801-11
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
10K
10K
150
2.2K
22
1/16W
1/16W
1/16W
1/10W
1/16W
100-C103JT16
100-C103JT16
100-C151JT16
100-C222JT10
100-C220JT16
R075
R076
R077
R078
R079
1-216-801-11
1-216-845-11
1-216-845-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
100K
100K
4.7K
10K
1/16W
1/16W
1/16W
1/16W
1/16W
100-C220JT16
100-C104JT16
100-C104JT16
100-C472JT16
100-C103JT16
R080
R081
R082
1-216-829-11 METAL CHIP
1-216-295-00 SHORT
1-216-850-11 RES-CHIP
4.7K
0
270K
1/16W 100-C472JT16
100-CR00JT10
1/16W 100-C274JT16
100-C472JT16
100-C562JT16
100-C472JT16
100-C103JT16
100-C103JT16
DESCRIPTION
REMARK
R084
R085
1-216-829-11 METAL CHIP
1-216-829-11 METAL CHIP
4.7K
4.7K
1/16W 100-C472JT16
1/16W 100-C472JT16
R086
R087
R088
R090
R091
1-216-829-11
1-216-829-11
1-216-864-11
1-216-833-11
1-216-864-11
METAL CHIP
METAL CHIP
SHORT
METAL CHIP
SHORT
4.7K
4.7K
0
10K
0
1/16W 100-C472JT16
1/16W 100-C472JT16
100-CR00JT16
1/16W 100-C103JT16
100-CR00JT16
R092
R093
R094
R095
R096
1-216-841-11
1-216-295-00
1-216-817-11
1-216-817-11
1-216-801-11
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
47K
0
470
470
22
1/16W 100-C473JT16
100-CR00JT10
1/16W 100-C471JT16
1/16W 100-C471JT16
1/16W 100-C220JT16
R097
R098
R099
R100
R101
1-216-803-11
1-216-841-11
1-216-864-11
1-216-850-11
1-216-850-11
RES-CHIP
METAL CHIP
SHORT
RES-CHIP
RES-CHIP
33
47K
0
270K
270K
1/16W 100C330JT16
1/16W 100-C473JT16
100-CR00JT16
1/16W 100-C274JT16
1/16W 100-C274JT16
R102
R103
R104
R105
R106
1-216-850-11
1-216-850-11
1-216-850-11
1-216-825-11
1-216-821-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
270K
270K
270K
2.2K
1K
1/16W
1/16W
1/16W
1/16W
1/16W
R107
R108
R110
R111
R112
1-216-809-11
1-216-817-11
1-216-864-11
1-216-835-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT
RES-CHIP
METAL CHIP
100
470
0
15K
1K
1/16W 100-C101JT16
1/16W 100-C471JT16
100-CR00JT16
1/16W
1/16W 100-C102JT16
R113
R114
R116
R118
R119
1-216-809-11
1-216-829-11
1-216-864-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
100
4.7K
0
4.7K
4.7K
1/16W 100-C101JT16
1/16W 100-C472JT16
100-CR00JT16
1/16W 100-C472JT16
1/16W 100-C472JT16
R120
R121
R122
R123
R124
1-216-833-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
1K
1K
1/16W
1/16W
1/16W
1/16W
1/16W
R125
R126
R127
R128
R131
1-216-817-11
1-216-864-11
1-216-864-11
1-216-811-11
1-216-817-11
METAL CHIP
SHORT
SHORT
RES-CHIP
METAL CHIP
470
0
0
150
470
1/16W 100-C471JT16
100-CR00JT16
100-CR00JT16
1/16W 100-C151JT16
1/16W 100-C471JT16
100-C274JT16
100-C274JT16
100-C274JT16
100-C222JT16
100-C102JT16
100-C103JT16
100-C103JT16
100-C103JT16
100-C102JT16
100-C102JT16
<CRYSTAL>
X001
1-795-093-11 OSCILLATOR, CRYSTAL
131-11059201
****************************************************************************************
H MOUNT
****************
<DIODE>
6-3
D801
153-12597G418
SDM-M51
(h)(j1)(j2)
DESCRIPTION
REMARK
REF.NO. PART NO.
<SWITCH>
DESCRIPTION
REMARK
<JACK>
S801
S802
S803
S804
S805
1-571-404-11
1-571-404-11
1-571-404-11
1-571-404-11
1-571-404-11
SWITCH, KEY BOARD
SWITCH, KEY BOARD
SWITCH, KEY BOARD
SWITCH, KEY BOARD
SWITCH, KEY BOARD
202-HJTSAC2
202-HJTSAC2
202-HJTSAC2
202-HJTSAC2
202-HJTSAC2
S806
S807
1-571-404-11 SWITCH, KEY BOARD
1-571-404-11 SWITCH, KEY BOARD
202-HJTSAC2
202-HJTSAC2
J901
J902
J903
J907
1-779-745-21
1-573-792-11
1-774-361-11
1-507-834-31
JACK, DC
CONNECTOR, MINIATURE DIN 4P
CONNECTOR, D SUB 15P
JACK
203-0139001
203-0411041
203-1511201
203-013509D
SDM-M51
REF.NO. PART NO.
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque ¡ sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
<COIL>
L901
L902
143-BWR6H0610
143-3L350908
1-469-978-11 INDUCTOR 0UH
****************************************************************************************
J1 MOUNT
****************
****************************************************************************************
J2 MOUNT
****************
<CAPACITOR>
C901
C902
C903
C904
1-130-495-00
1-104-666-11
1-102-074-00
1-102-074-00
MYLAR
ELECT
CERAMIC
CERAMIC
0.1UF
220UF
0.001UF
0.001UF
50V 122-10425ZYF
25V
120-22725SM
50V
122-102
50V
122-102
<CAPACITOR>
C701
C702
<DIODE>
1-126-791-11 ELECT
1-126-791-11 ELECT
10UF
10UF
16V
16V
120-10616SS
120-10616SS
<JACK>
D901
D902
D906
D907
D908
1-808-077-11
8-719-991-33
8-719-109-85
8-719-109-85
8-719-109-85
DIODE SB540
DIODE 1SS133T-77
DIODE MTZJ-T-72-5.1B
DIODE MTZJ-T-72-5.1B
DIODE MTZJ-T-72-5.1B
150-00SB540
152-0141480
150-01051B0
150-01051B0
150-01051B0
D909
D910
D911
8-719-109-85 DIODE MTZJ-T-72-5.1B
8-719-109-85 DIODE MTZJ-T-72-5.1B
8-719-109-85 DIODE MTZJ-T-72-5.1B
150-01051B0
150-01051B0
150-01051B0
J701
1-507-899-31 JACK (SMALL TYPE)
<RESISTOR>
R701
R702
1-215-401-11 METAL
1-215-401-11 METAL
150
150
1/4W
1/4W
100-151
100-151
9-978-683-01 2000IL24189-1
Sony Corporation
9-978-683-01
Computer Display Division Company
Computer Display Div.
– 6-4
42 –
English
2000IL24189-1
Printed in Japan
© 2000.9