Download Here - DCEmulation

TRINITRON® COLOR VIDEO MONITOR
BVM-14G1A/14G1E/14G1U
BVM-14G5A/14G5E/14G5U
BVM-20G1A/20G1E/20G1U
CHASSIS No. SCC-N52D-A (AUS)/J32H-A (AEP)/H99J-A (U/C)
CHASSIS No. SCC-N52E-A (AUS)/J32J-A (AEP)/H99K-A (U/C)
CHASSIS No. SCC-N52C-A (AUS)/J32G-A (AEP)/H99H-A (U/C)
MONITOR CONTROL UNIT
BKM-10R
OPERATION AND MAINTENANCE MANUAL [English]
1st Edition
Serial No. 2000001 and Higher
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injuly, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
WARNING!!
ATTENTION!!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BECAUSE
OF LIVE CHASSIS.
THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED
TO THE AC POWER LINE.
AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION PROVENANT
D’UN CHÁSSIS SOUS TENSION, UN TRANSFORMATEUR
D’ISOLEMENT DOIT ETRE UTILISÉ LORS DE TOUT DÉPANNAGE.
LE CHÁSSIS DE CE RÉCEPTEUR EST DIRECTEMENT
RACCORDÉ Á L’ALIMENTATION SECTEUR.
SAFETY-RELATED COMPONENT WARNING !!
ATTENTION AUX COMPOSANTS RELATIFS ÁLA
SÉCURITÉ!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE
CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS
MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL
COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS
SUSPECTED.
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET PAR UNE
MAPQUE ! SUR LES SCHÉMAS DE PRINCIPE, LES VUES
EXPLOSÉES ET LES LISTES DE PIECES CONT D’UNE
IMPORTANCE CRITIQUE POUR LA SÉCURITÉ DU
FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES
COMPOSANTS SONY DONT LE NUMÉRO DE PIÉCE EST INDIQUÉ
DANS LE PRÉSENT MANUEL OU DANS DES SUPPLÉMENTS
PUBLIÉS PAR SONY. LES RÉGLAGES DE CIRCUIT DONT
L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU
FONCTIONNEMENT SONT IDENTIFIES DANS LE PRÉSENT
MANUEL. SUIVRE CES PROCÉDURES LORS DE CHAQUE
REMPLACEMENT DE COMPOSANTS CRITIQUES, OU
LORSQU’UN MAUVAIS FONCTIONNEMENT EST SUSPECTÉ.
SAFETY CHECK-OUT
(US Model only)
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3.
Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain
that you have replaced all the insulators.
4.
Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair Point them out to the
customer and recommend their replacement.
5.
Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
6.
Check the line cord for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
7.
Check the condition of the monopole antenna (if any).
Make sure the end is not broken off, and has the plastic cap on
it. Point out the danger of impalement on a broken antenna to the
customer, and recommend the antenna’s replacement.
8.
Check the B+ and HV to see they are at the values specified.
Make sure your instruments are accurate; be suspicious of your
HV meter if sets always have low HV.
9.
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
HOW TO FIND A GOOD EARTH GROUND
A cold-water pipe is guaranteed earth ground; the cover-plate
retaining screw on most AC outlet boxes is also at earth ground. If
the retaining screw is to be used as your earth-ground, verify that it
is at ground by measuring the resistance between it and a coldwater
pipe with an ohmmeter. The reading should be zero ohms. If a coldwater pipe is not accessible, connect a 60-100 watts trouble light (not
a neon lamp) between the hot side of the receptacle and the retaining
screw. Try both slots, if necessary, to locate the hot side of the line,
the lamp should light at normal brilliance if the screw is at ground
potential. (See Fig. B)
To Exposed Metal
Parts on Set
Trouble Light
AC Outlet Box
0.15µF
1.5kΩ
AC
voltmeter
(0.75V)
Ohmmeter
Cold-water Pipe
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
Fig. B. Checking for earth ground.
1 (P)
TABLE OF CONTENTS
1. OPERATING INSTRUCTIONS
Operating Instructions (BVM-20G1U/14G1U/14G5U) .............................. 1-1
Operating Instructions (BKM-10R) ........................................................... 1-31
2. SERVICE INFORMATIONS
2-1.
2-2.
Circuit Boards Location ............................................................................... 2-1
2-1-1. BVM-14G5A/14G5E/14G5U ..................................................... 2-1
2-1-2. BVM-14G1A/14G1E/14G1U/20G1A/20G1E/20G1U ............... 2-1
2-1-3. BKM-10R .................................................................................... 2-2
Disassembly ................................................................................................. 2-3
2-2-1-1. Cabinet Removal
(14G1A/14G1E/14G1U/14G5A/14G5E/14G5U) ....................... 2-3
2-2-1-2. Cabinet Removal (20G1A/20G1E/20G1U) ................................ 2-3
2-2-2-1. FBT Block Assy Removal
(14G1A/14G1E/14G1U/14G5A/14G5E/14G5U) ....................... 2-4
2-2-2-2. FBT Block Assy Removal (20G1A/20G1E/20G1U) .................. 2-4
2-2-3. E and G Boards Removal and Check .......................................... 2-5
2-2-4. BC and BK Boards Removal and Check .................................... 2-5
2-2-5-1. Card Slot Assy Removal
(14G1A/14G1E/14G1U/14G5A/14G5E/14G5U) ....................... 2-6
2-2-5-2. Card Slot Assy Removal (20G1A/20G1E/20G1U) ..................... 2-6
2-2-6. TA and TB Boards Removal ....................................................... 2-7
2-2-7-1. YA, YB and YC Boards Removal (14G1A/14G1E/14G1U) ....... 2-7
2-2-7-1-1. Bezel Assy Removal (14G5A/14G5E/14G5U) ........................ 2-8
2-2-7-1-2. HA, HB, YA, YB and YC Boards Removal
(14G5A/14G5E/14G5U) .......................................................... 2-8
2-2-7-2. YA, YB and YC Boards Removal (20G1A/20G1E/20G1U) ....... 2-9
2-2-8-1. Picture Tube Removal
(14G1A/14G1E/14G1U/14G5A/14G5E/14G5U) ....................... 2-9
2-2-8-2. Picture Tube Removal (20G1A/20G1E/20G1U) ...................... 2-10
2-2-9. Upper Cover Removal (BKM-10R) .......................................... 2-11
2-2-10. HA and HB Board Removal (BKM-10R) ................................. 2-11
2-2-11. HC Board Removal (BKM-10R) .............................................. 2-12
3. SET-UP ADJUSTMENTS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
Preparations .................................................................................................. 3-1
Focus Adjustment ......................................................................................... 3-2
Landing Adjustment ..................................................................................... 3-2
H Blanking Adjustment ................................................................................ 3-3
V Blanking Adjustment ................................................................................ 3-5
Linearity Adjustment .................................................................................... 3-6
1
3-7.
3-8.
3-9.
Convergence Adjustment ............................................................................. 3-7
3-7-1. Static Convergence Adjustment .................................................. 3-8
3-7-2. 20-inch Model Convergence Adjustment .................................... 3-9
3-7-3. 14-inch Model Convergence Adjustment .................................. 3-10
G2 Adjustment ........................................................................................... 3-11
White Balance Adjustment ......................................................................... 3-12
4. SAFETY RELATED ADJUSTMENTS
+B (120V) Voltage Check ............................................................................ 4-1
High Voltage Regulator Check ..................................................................... 4-1
High Voltage Hold-Down Check .................................................................. 4-2
Beam Current Protector Check .................................................................... 4-2
5. CIRCUIT ADJUSTMENTS
5-1.
5-2.
5-3.
BK Board ..................................................................................................... 5-1
BC Board .................................................................................................... 5-10
E Board ....................................................................................................... 5-11
6. CIRCUIT DESCRIPTIONS
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
BK Board Descriptions ................................................................................ 6-1
BC Board Descriptions ................................................................................ 6-3
E Board Descriptions ................................................................................... 6-4
C Board Descriptions ................................................................................... 6-7
Power Supply Circuit Descriptions (G Board) ............................................. 6-7
Control Unit Descriptions (BVM-14G5, BKM-10R) .................................. 6-9
7. Semiconductors ................................................................................... 7-1
8. EXPLODED VIEWS
8-1.
8-2.
8-3.
8-4.
8-5.
8-6.
8-7.
2
Bezel, Cabinet (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U) ............... 8-2
Card Slot (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U) ........................ 8-4
Picture Tube (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U) .................. 8-6
Bezel, Cabinet (20G1A/20G1E/20G1U) ..................................................... 8-8
Card Slot (20G1A/20G1E/20G1U) ............................................................ 8-10
Picture Tube (20G1A/20G1E/20G1U) ....................................................... 8-12
Control Unit (BKM-10R) ........................................................................... 8-14
9. ELECTRICAL PARTS LIST ............................................................. 9-1
10. BLOCK DIAGRAM
Overall (1/2) ............................................................................................... 10-2
Overall (2/2) ............................................................................................... 10-3
BK (1/4) ..................................................................................................... 10-4
BK (2/4) ..................................................................................................... 10-5
BK (3/4) ..................................................................................................... 10-6
BK (4/4) ..................................................................................................... 10-7
BC (1/2) ...................................................................................................... 10-8
BC (2/2) ...................................................................................................... 10-9
E (1/2)....................................................................................................... 10-10
E (2/2)....................................................................................................... 10-11
G ............................................................................................................... 10-12
HA, HB, HC, HD ..................................................................................... 10-13
11. DIAGRAM
11-1. Printed Wiring Boards ................................................................................ 11-1
BK
................................................................................................... 11-2
BC
................................................................................................... 11-4
E
................................................................................................... 11-6
G
................................................................................................... 11-8
C
................................................................................................. 11-10
HD
................................................................................................. 11-10
P
................................................................................................. 11-10
YA
................................................................................................. 11-10
YB
................................................................................................. 11-10
YC
................................................................................................. 11-10
HA
................................................................................................. 11-11
HB
................................................................................................. 11-11
HC
................................................................................................. 11-12
TA
................................................................................................. 11-13
TB
................................................................................................. 11-14
11-2. Schematic Diagrams................................................................................. 11-15
FRAME (1/3) ......................................................................................... 11-17
FRAME (2/3) ......................................................................................... 11-18
FRAME (3/3) ......................................................................................... 11-19
BK (1/9) ................................................................................................. 11-20
BK (2/9) ................................................................................................. 11-21
BK (3/9) ................................................................................................. 11-22
BK (4/9) ................................................................................................. 11-23
BK (5/9) ................................................................................................. 11-24
3
BK (6/9) ................................................................................................. 11-25
BK (7/9) ................................................................................................. 11-26
BK (8/9) ................................................................................................. 11-27
BK (9/9) ................................................................................................. 11-28
BC (1/4) ................................................................................................. 11-31
BC (2/4) ................................................................................................. 11-32
BC (3/4) ................................................................................................. 11-33
BC (4/4) ................................................................................................. 11-34
E (1/4) ................................................................................................. 11-37
E (2/4) ................................................................................................. 11-38
E (3/4) ................................................................................................. 11-39
E (4/4) ................................................................................................. 11-40
C
................................................................................................. 11-43
P
................................................................................................. 11-44
YA
................................................................................................. 11-45
YB
................................................................................................. 11-45
YC
................................................................................................. 11-45
HD
................................................................................................. 11-45
G (1/2) ................................................................................................. 11-46
G (2/2) ................................................................................................. 11-47
HA
................................................................................................. 11-49
HB
................................................................................................. 11-50
HC
................................................................................................. 11-51
TA
................................................................................................. 11-53
TB
................................................................................................. 11-54
4
WARNING
TRINITRON® COLOR VIDEO MONITOR
BVM-20G1U/20G1E/20G1A
BVM-14G1U/14G1E/14G1A
BVM-14G5U/14G5E/14G5A
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended
by the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
ATTENTION
Il y a un risque d’explosion si la pile est mal insérée.
Remplacer la pile uniquement par une pile de même type ou
de type équivalent recommandé par le fabricant. Jeter les
piles usées conformément aux instructions du fabricant.
AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas
exposer cet appareil à la pluie ou à l’humidité.
WARNUNG
Um Feuergefahr und die Gefahr eines elektrischen SchIages
zu vermeiden, darf das Gerät weder Regen noch
Feuchtigkeit ausgesetzt werden.
Um einen elektrischen Schlag zu vermeiden, darf das
Gehäuse nicht geöffnet werden. Überlassen Sie
Wartungsarbeiten stets nur einem Fachmann.
ADVERTENCIA
Para evitar incendios o el riesgo de electrocución, no
exponga la unidad a la lluvia ni a la humedad.
Para evitar descargas eléctricas, no abra la unidad. En caso
de avería, solicite los servicios de personal cualificado.
ATTENZIONE
Per evitare incendi o cortocircuiti, l’apparecchio non deve
essere esposto alla pioggia o all’umidità.
Per evitare scosse elettriche, non aprite l’apparecchio. Per
le riparazioni rivolgetevi solo a personale qualificato.
PRECAUCION
Peligro de explosión en caso de haberse instalado
incorrectamente la betería.
Cambie sólo por una del mismo tipo o especificaciones
equivalentes, de entre las recomendadas por el fabricante.
Las baterías viejas se deben eliminar siguiendo las
instrucciones del fabricante.
ATTENZIONE:
Pericolo di esplosione se la pila viene sostituita
scorrettamente.
Sostituirla solo con un’altra uguale o di un tipo equivalente
consigliato dal fabbricante. Gettare via le pile usate secondo
le istruzioni del fabbricante.
Note
The socket-outlet should be installed near the equipment and
be easily accessible.
Remarque
La prise doit être près de l’appareil et facile d’accès.
Hinweis
Zur Trennung vom Netz ist der Netzstecker aus der
Steckdose zu ziehen, welche sich in der Nähe des Gerätes
befinden muß und leicht zugänglich sein soll.
Nota
La presa di corrente deve essere situata vicino
all’apparecchio e deve essere facilmente accessibile.
OPERATION MANUAL [English]
1st Edition
Serial No. 2000001 and Higher
1-1
This section is extracted from
operation manual.
Nota
La toma mural debe estar instalada cerca del equipo y debe
accederse a ésta con facilidad.
SECTION 1
OPERATING INSTRUCTIONS
Afin d’écarter tout risque d’électrocution, garder le coffret
fermé. Ne confier l’entretien de l’appareil qu’à un personnel
qualifié.
VORSICHT:
Es besteht Explosionsgefahr, wenn die Batterie inkorrekt
eingelegt wird.
Es darf nur eine identische oder eine vom Hersteller
empfohlene Batterie des gleichen Typs eingesetzt werden.
Entladene Batterien sind nach den Anweisungen des
Herstellers zu entsorgen.
1-2
WARNING: THIS WARNING IS APPLICABLE FOR USA
ONLY.
If used in USA, use the UL LISTED power cord specified
below.
DO NOT USE ANY OTHER POWER CORD.
Plug Cap
Cord
Length
Rating
Parallel blade with ground pin
(NEMA 5-15P Configuration)
Type SVT, three 16 or 18 AWG wires
Less than 2.5 m (8 ft 3 in)
Minimum 10 A, 125 V
Using this unit at a voltage other than 120V may require the
use of a different line cord or attachment plug, or both. To
reduce the risk of fire or electric shock, refer servicing to
qualified service personnel.
For customers in the USA
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with the
limits for a digital device pursuant to Subpart B of Part 15 of
FCC Rules.
For customers in Canada
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Pour les utilisateurs au Canada
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
Für Kunden in Deutschland
Dieses Produkt kann im kommerziellen und in begrenztem
Maße auch im industriellen Bereich eingesetzt werden. Dies
ist eine Einrichtung, welche die Funk-Entstörung nach
Klasse B besitzt.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
• Dit apparaat bevat een Li-ion batterij voor memory back-up.
• De batterij voor memory back-up is vastgesoldeerd op de
BC printplaat BAT1.
• Raadpleeg uw leverancier over de verwijdering van de
batterij op het moment dat u het apparaat bij einde
levensduur afdankt.
• Gooi de batterij niet weg, maar lever hem in als KCA.
Note
Be sure to use the supplied power cord for this monitor, or
this monitor may not conform with the FCC Rules or EEC
Directive 89/336/EEC.
Remarque
Utiliser le cordon d’alimentation fourni pour ce moniteur,
sinon il pourrait ne pas être conforme aux règles FCC ou à la
directive CEE 89/336/EEC.
Hinweis
Dieser Monitor darf ausschließlich mit dem mitgelieferten
Netzkabel betrieben werden, weil anderenfalls der Monitor
nicht mehr die FCC-Vorschriften oder die EG-Richtlinie 89/
336/EWG erfüllt.
Nota
Utilice sin falta el cable eléctrico que viene con este monitor;
de lo contrario el monitor puede no cumplir con los
reglamentos de la FCC o de la directiva 89/336/EEC de la
Comunidad Europea.
Nota
Assicurarsi di usare il cavo di alimentazione in dotazione per
questo monitor, altrimenti il monitor può non essere
conforme alle norme FCC o alla Direttiva CEE/89/336.
ATTENTION - When the product is installed in a rack:
a) Elevated operating ambient temperature
If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment
may be greater than room ambient. Therefore,
consideration should be given to installing the equipment
in an environment compatible with the manufacture’s
maximum rated ambient temperature (Tmra: 0°C to 35°C
(32°F to 95°F)).
b) Reduced air flow
Installation of the equipment in a rack should be such that
the amount of air flow required for safe operation of the
equipment is not compromised.
c) Mechanical loading
Mounting of the equipment in the rack should be such
that a hazardous condition is not achieved due to uneven
mechanical loading.
d) Circuit overloading
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that
overloading of circuits might have on overcurrent
protection and supply wiring.
Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern.
e) Reliable earthing
Reliable earthing of rack-mounted equipment should e
maintained. Particular attention should be given to supply
connections other than direct connections to the branch
circuit (e.g., use of power strips).
f) Gap keeping
Upper and lower gap of rack-mounted equipment should
be kept 44 mm (1 3⁄4 inches).
For the customers in the United Kingdom
WARNING
THIS APPARATUS MUST BE EARTHED
IMPORTANT
The wires in this mains lead are coloured in accordance with
the following code:
Green-and-yellow: Earth
Blue:
Neutral
Brown:
Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be
connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol Y or coloured green or
green-and-yellow.
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
Ensure that your equipment is connected correctly - if you
are in any doubt consult a qualified electrician.
Table of Contents
Table of contens
Chapter 1
Overview
Precaution ............................................................................................... 3
Overview .................................................................................................. 4
Features .......................................................................................... 4
Options ........................................................................................... 5
Connector Panel Configuration ...................................................... 7
Location and Function of Parts ............................................................. 9
Front Panel ..................................................................................... 9
Rear Panel .................................................................................... 15
Chapter 2
Menu
Menu Structure ..................................................................................... 18
Displaying the Menus................................................................... 18
ADDRESS Menu ......................................................................... 19
Menu Directories .......................................................................... 20
Basic Menu Operations ........................................................................ 22
Menu Operation Buttons .............................................................. 22
Menu Operation............................................................................ 22
Preset Adjustment of the Picture Level Control Knobs —
CONTROL PRESET ADJ Menu ................................................ 25
Overview ...................................................................................... 25
Structure of the CONTROL PRESET ADJ Menu [A] ................. 25
Setting Lists in the CONTROL PRESET ADJ Menu .................. 25
Adjusting the Color Temperature — COLOR TEMP ADJ
Menu ............................................................................................... 27
Overview ...................................................................................... 27
Structure of the COLOR TEMP ADJ Menu [B] .......................... 28
Setting Lists in the COLOR TEMP ADJ Menu ........................... 29
Setting the Input Configuration (SET UP 1) — INPUT
CONFIGURATION Menu ........................................................... 32
Overview ...................................................................................... 32
Structure of the INPUT CONFIGURATION Menu [C1] ............ 32
Setting Lists in the INPUT CONFIGURATION Menu ............... 33
Assigning the Remote Control Functions (SET UP 2) —
REMOTE Menu ............................................................................ 35
Overview ...................................................................................... 35
Structure of the REMOTE Menu [C2] ......................................... 35
Setting Lists of the REMOTE Menu ............................................ 35
Setting the Password (SET UP 3) — PASSWORD Menu ................ 37
Overview ...................................................................................... 37
Structure of the PASSWORD Menu [C3] .................................... 37
Setting Lists of the PASSWORD Menu ...................................... 37
Setting Power-Up Conditions and Decoder (SET UP 4) —
SYSTEM CONFIGURATION Menu .......................................... 39
Overview ...................................................................................... 39
Structure of the SYSTEM CONFIGURATION Menu [C4] ........ 39
Setting Lists of the SYSTEM CONFIGURATION Menu........... 40
(Continued)
1
Chapter 2
Menu
Setting the Screen Display (SET UP 5) —
ON SCREEN SET Menu .............................................................. 41
Overview ...................................................................................... 41
Structure of the ON SCREEN SET Menu [C5] ........................... 41
Setting Lists of the ON SCREEN SET Menu .............................. 41
Convergence Adjustments (SET UP 6) — ALIGNMENT Menu..... 42
Overview ...................................................................................... 42
Structure of the ALIGNMENT Menu [C6] .................................. 42
Setting Lists of the ALIGNMENT Menu .................................... 42
Using Extended Functions (SET UP 7) — EXTEND Menu ............. 44
Overview ...................................................................................... 44
Structure of the EXTEND Menu [C7] .......................................... 44
Setting Lists of the EXTEND Menu ............................................ 45
Monitor Memory Card Data Operations —
MEMORY CARD Menu .............................................................. 46
Overview ...................................................................................... 46
Structure of the MEMORY CARD Menu [D] ............................. 46
Setting Lists of the MENU CARD Menu .................................... 46
Monitor-to-Monitor Data Copy — COPY Menu .............................. 47
Overview ...................................................................................... 47
Structure of the COPY Menu [E] ................................................. 47
Setting Lists of the COPY Menu.................................................. 47
Displaying Information About the Monitor — STATUS Menu ...... 48
Overview ...................................................................................... 48
Structure of the STATUS Menu [F] ............................................. 48
Setting Lists of the STATUS Menu ............................................. 48
Selecting the Monitor to Control — ADDRESS Menu ..................... 49
Overview ...................................................................................... 49
Displaying the ADDRESS Menu ................................................. 49
Cancelling the Remote Control Mode.......................................... 50
Exiting the ADDRESS Menu ....................................................... 50
Chapter 3
Appendix
Specifications ......................................................................................... 51
Connection Cable Specifications for Color Temperature Probes 54
2
1-3
1-4
Precaution
Overview
• Operate the unit only with a power source as
specified in “Specifications” section.
• The nameplate indicating operating voltage, power
consumption, etc., is located at the rear.
• Should any solid object or liquid fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it any further.
• Do not drop or place heavy objects on the power
cord. If the power cord is damaged, turn off the
power immediately. It is dangerous to use the unit
with a damaged power cord.
• Unplug the unit from the wall outlet if it is not to be
used for several days or more.
• Disconnect the power cord from the AC outlet by
grasping the plug, not by pulling the cord.
• The socket-outlet shall be installed near the
equipment and shall be easily accessible.
Do not throw away the carton and packing materials.
They make an ideal container which to transport the
unit. When shipping the unit to another location,
repack it as illustrated on the carton.
On installation
• Allow adequate air circulation to prevent internal heat
build-up.
Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation holes.
• Do not install the unit in a location near heat sources
such as radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical vibration
or shock.
On cleaning
To keep the unit looking brand-new, periodically clean
it with a mild detergent solution. Never use strong
solvents such as thinner or benzine, or abrasive
cleansers since they will damage the cabinet. As a
safety precaution, unplug the unit before cleaning it.
If you have any questions about this unit, contact your
authorized Sony dealer.
Chapter 1 Overview
On repacking
Chapter 1 Overview
On safety
The BVM-20G1U/20G1E/20G1A are 20 -inch
Trinitoron®1) Color Monitors. The BVM-14G1U/
14G1E/14G1A/14G5U/14G5E/14G5A are 14-inch
Trinitoron® Color Monitors. They are suitable for
television stations or video production houses, where
precise image reproduction is required.
Features
High resolution picture tube
The HR Trinitron picture tube produces a clear, high
resolution image.
On magnetism
• Do not place the unit near any objects or pieces of
equipment which generate magnetism, such as
magnets, speakers, electric clocks, toys using
magnets, health appliances, etc. Magnetism will
cause picture bounce, oscillations or picture
discoloration.
• Also, the picture may become fuzzy or the colors
may not reproduce correctly due to earth magnetism.
This depends on direction that the unit is installed.
This is not equipment failure. In such a case, simply
degauss the unit.
On the CRT
• Dust accumulates on the CRT easily. Clean the CRT
when necessary with a soft cloth.
The surface of the CRT is easily scratched; therefore,
do not rub or touch the surface of the CRT
unnecessarily since this may result in a scratched
picture tube.
• If you touch the surface of the CRT, you may feel a
weak electrical shock. This is simply static electricity
that is generated on the surface of the CRT. It will not
affect the human body.
Aperture
grille pitch
Resolution at the
center of the picture
BV-20G1U/20G1E/
20G1A
0.3 mm
800 TV lines
BV-14G1U/14G1E/
14G1A/14G5U/
14G5E/14G5A
0.25 mm
800 TV lines
Model
Separate control unit (BVM-20G1U/20G1E/
20G1A/14G1U/14G1E/14G1A only)
The BVM-20G1U/20G1E/20G1A/14G1U/14G1E/
14G1A are controlled by a separate control unit, such
as an optional BKM-10R/11R Monitor Control unit.
Using a separate control unit reduces the space needed
for the equipment. The BVM-20G1U/20G1E/20G1A
can be connected to the BKM-10R via an optional
BKM-32H Monitor Control Unit Attachment Kit.
Controlling monitor groups
Up to 32 monitors can be controlled from this monitor.
First, using the monitor menus, assign a monitor
address number to each monitor, divide the monitors
into groups, and assign a group number to each group.
Then you can use this monitor to control individual
monitors or monitor groups simply by entering
monitor address or group numbers. You can also
execute the same operation on all connected monitors,
or use this monitor to put all connected monitors into
the same setup and adjustment state.
Setup and adjustment with the Monitor
Memory Card
You can use an optional BKM-12Y Monitor Memory
Card to save and load monitor setup and adjustment
data. If your system includes more than one monitor,
you can use the monitor memory cards to exchange
data between monitors. This makes it easy to put all
monitors in your system into the same setup and
adjustment state.
Standard auto alignment system
Decoder chroma and phase adjustment, as well as
color temperature control, may be performed with the
auto alignment system. This makes it possible to
coordinate settings among multiple monitors.
Expandable input capability
The input connector configuration may be easily
modified by simply sliding optional decoder adaptor or
the input expansion adaptor into input option slot at the
rear of the monitor.
4:3/16:9 dual aspect ratio design
This monitor can be changed to either 4:3 or 16:9
aspect ratio with just a simple switching operation. The
screen can be also changed to 4:3 or 16:9 display by
the replacement of a mask (no tools required).
Stable color temperature
The internal beam current feedback circuit maintains a
constant color temperature over long periods of time.
Blue-only mode convenient for monitoring
noise
All three CRT cathodes can be driven with a blue
signal, producing a monochrome display. This mode
is convenient for chroma and phase adjustment, and
for monitoring VTR noise.
Menu operation
The monitor’s various functions and operating
conditions can be set with on-screen menus.
........................................................................................................................................................................................................
1) Trinitron ® is a registered trademark of Sony Corporation.
3
4
Overview
BKM-33H14 Monitor 16:9 Mask
Adapts the BVM-14G1U/14G1E/14G1A/14G5U/
14G5E/14G5A screen for 16:9 aspect ratio display.
For installation
BKM-30E20 Rack Mount Kit
Rack mount kit for mounting the BVM-20G1U/
20G1E/20G1A in an EIA standard 19-inch rack.
For external control
BKM-10R/11R Monitor Control Unit
A controller for this monitor and other BVM-series
video monitors, allowing you to control multiple
monitors from one control unit.
BKM-12Y Monitor Memory Card
Memory cards which can be read and written by the
BVM-14G5U/14G5E/14G5A or BKM-10R/11R.
BKM-14L Auto Setup Probe
This probe allows automatic adjustment of this
monitor’s color temperature.
For screen
BKM-33H20 Monitor 16:9 Mask
Adapts the BVM-20G1U/20G1E/20G1A screen for
16:9 aspect ratio display.
BKM-21D SDI Multi Decoder Adaptor
Includes decoders for serial digital signals (525/625
component and NTSC/PAL composite) and analog
composite signals (NTSC and PAL). Input/output
connectors for three serial digital channels and three
analog channels are equipped. The input signal type
for each connector is set with the INPUT
CONFIGURATION menu, in accordance with the
configuration of the connector panel.
BKM-24N NTSC Decoder Adaptor
Includes decoders for analog composite NTSC signals
and input/output connectors for six analog channels.
The input signal type for each connector is set with the
INPUT CONFIGURATION menu, in accordance with
the configuration of the connector panel.
BKM-30E14 Rack Mount Kit
Rack mount kit for mounting the BVM-14G5U/
14G5E/14G5A in an EIA standard 19-inch rack.
BKM-31E14 Rack Mount Kit
Rack mount kit for mounting the BVM-14G1U/
14G1E/14G1A in an EIA standard 19-inch rack.
BKM-32H Monitor Control Unit Attachment Kit
Assembly kit for attaching a BKM-10R Monitor
Control Unit to the BVM-20G1U/20G1E/20G1A.
Decoder and input expansion adaptors
Options
Chapter 1 Overview
Chapter 1 Overview
Other features
• Compatible with the ISR (Interactive Status
Reporting) system.
• Has both RS-485 serial remote and relay contact
parallel remote control connectors.
• Built-in safe area display and test signal generator for
crosshatch, 100% white signal, 20% gray signal, gray
scale, and PLUGE (Picture Line Up Generating
Equipment).
• Built-in Caption Vision decoder.
• Pulse cross function for simultaneous checking of the
horizontal and vertical synchronization signals. VITS
(Vertical Interval Test Signal) checking is also
possible.
• Auto and manual degaussing.
• Built-in CRT protection circuit.
• This monitor may be mounted in an EIA-standard 19inch rack, using an optional BKM-30E20/30E14/
31E14 Rack Mount Kit.
• Controllable from the optional BKM-10R/11R
Monitor Control Unit. (For details about connection
and operation, refer to the BKM-10R/11R Operation
Manual).
BKM-25P PAL Decoder Adaptor
Includes decoders for analog composite PAL signals
and input/output connectors for six analog channels.
The input signal type for each connector is set with the
INPUT CONFIGURATION menu, in accordance with
the configuration of the connector panel.
BKM-26M PAL-M Decoder Adaptor
Includes decoders for analog composite PAL-M
signals and input/output connectors for six analog
channels. The input signal type for each connector is
set with the INPUT CONFIGURATION menu, in
accordance with the configuration of the connector
panel.
The input connector panel is configured by sliding
optional decoder adaptor or input expansion adaptor
into the input option slot at the rear of the monitor.
Note
When installing the adaptor, be sure to perform the
necessary input signal setup with the INPUT
CONFIGURATION menu. If the setup is not
performed, the adaptors may not function correctly.
BKM-27T Tri-Standard Decoder Adaptor
Includes decoders for analog composite NTSC, PAL,
and SECAM signals and input/output connectors for
six analog channels. The input signal type for each
connector is set with the INPUT CONFIGURATION
menu, in accordance with the configuration of the
connector panel.
For information about the INPUT CONFIGURATION
menu, see “Setting the Input Configuration (SET UP 1)—
INPUT CONFIGURATION Menu” on page 32.
BKM-20D SDI 4:2:2 Decoder Adaptor
Includes decoders for serial digital component signals
(525/625). Input/output connectors for three serial
digital channels (component inputs only) and three
analog channels. The input signal type for each
connector is set with the INPUT CONFIGURATION
menu, in accordance with the configuration of the
connector panel.
5
BKM-28X Analog Input Expansion Adaptor
Increases the number of input/output channels.
Includes input/output connectors for six analog
channels. The input signal type for each connector is
set with the INPUT CONFIGURATION menu, in
accordance with the configuration of the connector
panel.
6
BKM-48X Analog Input Expansion Adaptor
Increases the number of input/output channels.
Includes input/output connectors for six analog
channels. For each input output connector, either
floating or ground can be selected by the switch inside
the board. The input signal type for each connector is
set with the INPUT CONFIGURATION menu, in
accordance with the configuration of the connector
panel.
1-5
1-6
Overview
Note on using the BKM-20D/21D
Connector Panel Configuration
Chapter 1 Overview
Notes
The BKM-20D and BKM-21D can not provide proper
active-through outputs if a signal whose format is not
selected in the INPUT CONFIGURATION menu is
input. (If AUTO is selected, input a signal which has
the same format with the signal monitored last.)
Chapter 1 Overview
The unit comes standard with connectors for one
channel of Y/R–Y/B–Y or RGB. By adding optional
decoder adaptor or input expansion adaptors, the input/
output connector panel can be assembled in a wide
variety of configurations. The signals that each of the
adaptors’ connectors supports are given in the table
below. The type of signal to be applied to each input/
output connector is set with the INPUT
CONFIGURATION menu.
When the input option slot on the rear of the monitor
has a BKM-20D/21D SDI Decoder Adaptor (option)
installed, if you remove and insert the analog input
connectors board, the radiation shield (see Fig. 2) of
the BKM-20D/21D may be damaged or detached.
Fig.1
For information about the INPUT CONFIGURATION
menu, see “Setting the Input Configuration (SET UP 1) —
INPUT CONFIGURATION Menu” on page 32.
Fig. 2
Input option slot (with a cover plate)
Radiation shield
Adaptor name
BKM-20D
SDI 4:2:2
Decoder
Adaptor
Serial
digital
input
Component
525/625
®
BKM-21D
SDI Multi
Decoder
Adaptor
BKM-24N
NTSC
Decoder
Adaptor
BKM-25P
PAL
Decoder
Adaptor
BKM-26M
PAL-M
Decoder
Adaptor
BKM-27T
TriStandard
Decoder
Adaptor
BKM-28X
Analog
Input
Expansion
Adaptor
BKM-48X
Analog
Input *
Expansion
Adaptor
®
Composite
NTSC
®
Composite
PAL
®
Analog Composite
input
NTSC
®
Composite
PAL
®
Analog input connectors board
®
®
®
When installing the analog input connectors board
again, remove the BKM-20D/21D temporarily while
carrying out the other operations, then reinstall it.
®
®
Composite
PAL-M
®
Composite
SECAM
Y/R–Y/B–Y
525/625
®
®
®
®
®
®
®
®
RGB
525/625
®
®
®
®
®
®
®
®
®
Y/C
NTSC
®
®
Y/C
PAL
Y/C
PAL-M
®
®
Number of digital
inputs
3
3
–
–
–
–
–
–
Number of analog
input
3
3
6
6
6
6
6
6
* : Equipped with floating/non-floating ground mode selector for HAM reduction
7
8
BKM-20D/21D
Analog input
connectors board
Location and Function of Parts
Front Panel
This manual explains the location and function of parts
and controls using the control panel of the BVM14G5U/14G5E/14G5A. The explanation applies to
BVM-14G1U/14G1E/14G1A/20G1U/20G1E/20G1A
with the BKM-10R/11R Monitor Control Unit.
Chapter 1 Overview
BVM-14G5U/14G5E/14G5A
1 Tally lamp
2 POWER switch
0 SHIFT button
3 DEGAUSS button
4 Numeric keypad
Chapter 1 Overview
Location and Function of Parts
1 Tally lamp
With factory settings, the Tally lamp lights when pins
No. 8 and No. 9 of the REMOTE 2 connector on the
rear panel are shorted. By changing the setting in the
REMOTE menu, different pins on the remote
connector can be used to control the tally lamp.
!¡ Function buttons
For information about the REMOTE menu, see “Assigning
the Remote Control Functions (SET UP 2) —REMOTE
Menu” on page 35.
5 MANUAL adjustment
buttons and knobs
!™ Monitor Memory
Card slot
6 Menu operation
buttons
!£ OPTION connector
7 POWER lamp
2 POWER switch
Press to turn on/off the monitor. By setting with the
ADDRESS menu, it is possible to turn on/off the
power of the specified monitors only, or of all
monitors at the same time.
8 STANDBY lamp
9 OVER LOAD lamp
For information about the ADDRESS menu, see “Selecting
the Monitor to Control - ADDRESS Menu” on page 49.
3 DEGAUSS button
Press to degauss the CRT (every time the monitor is
turned on, the CRT is degaussed automatically). To
degauss again, wait for more than five minutes.
BVM-20G1U/20G1E/20G1A/14G1U/14G1E/14G1A
Channel number entry method:
(In the explanation below, x and y represent any
digit between 1 and 9.)
When selecting a number from 1 to 9, press the x
button to display channel x. When selecting a
number from 10 to 99, press the 0, x, and y buttons
to display channel xy (a two-digit channel number).
5 MANUAL adjustment buttons and knobs
Each press of one of these buttons turns the button’s
green LED on or off. When the corresponding button
is on (lit), it is possible to manually adjust the contrast,
brightness, chroma and phase by turning the
corresponding knobs. They are also used to enter the
setting values with the menus. It is possible to set the
preset value for each adjusting item with the
CONTROL PRESET ADJ menu.
For Information about the CONTROL PRESET ADJ menu,
see “Preset Adjustment of the Picture Level Control Knobs CONTROL PRESET ADJ menu” on page 25.
Notes
When using the composite SECAM, composite PAL
D, component or SDI (component or composite serial
digital interface) format, note the following.
• The signal phase cannot be adjusted.
• The phase and chroma of RGB signals cannot be
adjusted.
CONTRAST
1 Tally lamp
4 Numeric keypad
Use to designate the channel number for the input
signal to be monitored, or to enter the setting values
with the menus.
MANUAL
CONTRAST button and
knob
BRIGHT
BRIGHT button and knob
INPUT
1
2
3
4
5
6
7
8
9
Del
0
Ent
CHROMA
Numeric buttons
CHROMA button and knob
PHASE
!£ OPTION connector
7 POWER lamp
Ent button: Confirms the
values and characters entered
(ENTER button of the menu
operation buttons 6 has the
same function).
8 STANDBY lamp
Del button: Deletes the values
and characters entered.
9 OVER LOAD lamp
(Illustration: BVM-20G1U/20G1E/20G1A)
9
10
PHASE button and knob:
Changes the items and
settings on the menus
1-7
1-8
Location and Function of Parts
6 Menu operation buttons
MENU button: Press to display the Menus.
DOWN
ENTER
UP/DOWN buttons: Press to select the
items and setting values.
ENTER button: Press to confirm the items
and values entered (Ent button on the
numeric keypad 4 has the same function).
For more information about menu operation, see “Basic
Menu Operations” on page 22.
Chapter 1 Overview
MENU
Chapter 1 Overview
UP
0 SHIFT button
Press to select one of the two functions designated to
the function buttons !¡.
Each time the SHIFT button is pressed, the LED turns
on (SHIFT ON: lit in orange) and off (SHIFT OFF: lit
in green).
SHIFT OFF: The functions indicated on the left side
of the function buttons can be used.
SHIFT ON: The functions indicated on the right side
of the function buttons can be used.
!¡ Function buttons
Change the operation conditions for the monitor.
Each time the button is pressed, the LED turns on and
turns off, and the operation conditions are changed.
Each button has two functions. Select one of the two
functions by pressing the SHIFT button 0. When the
SHIFT button is set to ON, the LED lights in orange,
and when the SHIFT button is set to OFF, the LED of
each button lights in green.
SHIFT OFF (LEDs of function buttons in green)
(Underscan) button: When this button is pushed in (ON), the picture is
underscanned by 3%, and four ends of the raster is displayed on the screen.
7 POWER lamp
Lights when the monitor is put into operation mode
from standby mode (see STANDBY lamp 8) by
pressing the POWER switch 2.
(H delay) button: When this button is pushed in (ON), the picture moves
horizontally, and a horizontal sync signal appears approximately one quarter in the
left edge of the screen.
• The brightness of the picture increases automatically, and it makes it easy to check
the sync part.
• If it is pressed together with the
button, a pulse cross picture is displayed.
Note
When the STANDBY lamp 8 is blinking, the monitor
cannot be put into operation mode (internal data
initialization is taking place). Wait until the
STANDBY lamp 8 is steadily lit.
(V delay) button: When this button is pushed in (ON), the picture moves vertically,
and a vertical sync signal appears approximately in the center of the screen.
• The brightness of the picture increases automatically, and it makes it easy to check
the sync part.
• If it is pressed together with
button, a pulse cross picture is displayed.
16 : 9
8 STANDBY lamp
Lights when the monitor is in standby mode. The
monitor will be in standby mode under the following
conditions:
• The MAIN POWER switch (on the rear panel) is
turned on (the STANDBY lamp will blink for a few
moments after the switch is turned on, then will
light).
• The monitor is changed from operation mode to
standby mode by external control.
SYNC
BLUE
ONLY
9 OVER LOAD lamp
Lights to warn of CRT overload.
MONO
R
APT
G
COMB
B
F1
F3
F2
F4
ADDRESS
SAFE
AREA
MONO button: When this button is pushed in (ON), a monochrome picture is displayed.
When the buttons is off, the monitor switches automatically between color and
monochrome mode, depending on the presence or absence of color burst signal.
APT (aperture) button: When this button is pushed in (ON), the frequency response
can be modified. The degree of modification is set with the menu.
This function is available when an optional decoder adaptor such as a BKM-24N is
installed.
COMB button: Turn the comb filter on and off.
This function is available when an optional decoder adaptor such as a BKM-24N is
installed.
F1 button: When this button is pushed in (ON), the characters disappear from the
monitor on the MANUAL menu of the level 2 of the CONTROL PRESET ADJ menu, the
MANUAL menu of the level 2 of the COLOR TEMP ADJ menu, and the ALIGNMENT
menu of the level 2 of SETUP menu.
F2 button: When this button is pushed in (ON), you can access directly the MANUAL
menu of the level 2 of the COLOR TEMP ADJ menu, if the short-cut function is assigned
to this button.
ADDRESS button: When this button is pushed in (ON), the ADDRESS menu appears
on the screen. By using the ADDRESS menu, operation conditions for multiple
monitors are set.
For more information about the ADDRESS menu, see “Selecting the Monitor to Control ADDRESS Menu” on page 49.
11
12
Location and Function of Parts
!™ Monitor Memory Card slot
Insert the BKM-12Y Monitor Memory Card
(optional).
SHIFT ON (LEDs of function buttons in orange)
SYNC button: When this button is pushed in (ON), the monitor synchronizes
to the sync signal input to the SYNC connectors on the rear panel (EXT
SYNC). When set to OFF, it synchronizes to the sync signal included in
the signals being monitored (INT SYNC).
Chapter 1 Overview
Chapter 1 Overview
16:9 button: When this button is pushed in (ON), the aspect ratio changes to
16:9, and when set to OFF, the aspect ratio changes to 4:3.
For information about operations on monitor memory card
data, see “Monitor Memory Card Data Operations —
MEMORY CARD menu” on page 46.
Note
Do not eject the monitor memory card while data is
being saved or loaded.
Proceed as illustrated to insert and eject the BKM-12Y
Monitor Memory Card.
Notes
16 : 9
• When INT SYNC is selected, use a component or YC signals including a
sync signal on the Y signal, and use RGB signal including a sync signal
on the G signal.
• To monitor serial digital signals, select INT SYNC.
To insert the BKM-12Y Monitor Memory Card
SYNC
BLUE
ONLY
MONO
R
APT
G
COMB
B
F1
F3
BLUE ONLY button: When this button is pushed in (ON), red and green
signals are cut, and only the blue signal is displayed as a monochrome
picture. It makes it easy to adjust CHROMA and to check VTR noise.
Monitor memory card insertion slot
R/G/B buttons: When these buttons are pushed in (ON), R(red), G(green),
and B(blue) beams are cut respectively.
Be careful not to let your hands
touch the connectors on the front
edge of the monitor memory card.
Push the monitor
memory card in
until the EJECT
button comes out.
EJECT button
Monitor memory card
F3/F4 buttons: For future expansion.
To eject the BKM-12Y Monitor Memory Card
F2
ADDRESS
F4
SAFE
AREA
SAFE AREA button: When this button is pushed in (ON), a safe area is
displayed on the screen.
EJECT button
Press the EJECT button to eject
the monitor memory card.
!£ OPTION connector
Connector for expansion.
13
14
Take out the
monitor memory
card.
1-9
1-10
Location and Function of Parts
Rear Panel
3 Analog input/output
connectors
Chapter 1 Overview
Chapter 1 Overview
BVM-14G5U/14G5E/14G5A
1 MAIN POWER switch
When turned on, the monitor enters standby mode. By
setting in the SYSTEM CONFIGURATION menu, the
monitor can also be set to enter operation mode when
the MAIN POWER switch is turned on.
For information about the SYSTEM CONFIGURATION
menu, see “Setting Power-Up Conditions and Decoder (SET
UP 4) —SYSTEM CONFIGURATION Menu” on page 39.
4 Input option slot
2 AC IN connector (3-pin)
Connects the monitor to an AC power source, via the
supplied AC power cord.
5 REMOTE 1 connectors
For information about the INPUT CONFIGURATION
menu, see “Setting the Input Configuration (SET UP 1)—
INPUT CONFIGURATION Menu” on page 32.
4 Input option slot
One optional decoder adaptor or input expansion
adaptor can be installed into this option slot.
5 REMOTE 1 connectors (female, D-sub 9-pin)
REMOTE 1
IN
REMOTE 1 IN connector
AC power cord (supplied)
6 REMOTE 2 connector
7 ISR connector
1 MAIN POWER switch
Cord stopper (supplied)
2 AC IN connector
Plug holder
OUT
Attach the cord stopper to the AC power cord, and connect it
to the plug holder so that the cord does not come loose.
3 Analog input/output connectors
BVM-20G1U/20G1E/20G1A/14G1U/14G1E/14G1A
ANALOG
IN
Y/G
Y/G connectors (BNC)
OUT
3 Analog input/output
connectors
IN
B-Y/B
4 Input option slot
B-Y/B connectors (BNC)
OUT
IN
R-Y/R
5 REMOTE 1 connectors
R-Y/R connectors (BNC)
OUT
IN
SYNC
6 REMOTE 2 connector
1 MAIN POWER switch
7 ISR connector
2 AC IN connector
SYNC connectors (BNC)
OUT
RGB signals, component signals (Y/R-Y/B-Y), or
composite sync signals can be fed in the IN
connectors. The type of signal applied to each
connector is set with the INPUT CONFIGURATION
menu. The OUT connectors are used for loop-through
output of the input signal. When not using loopthrough, connect a 75-ohm terminator (not supplied) to
the OUT connectors.
8 CONTROL UNIT connector
(Illustration: BVM-20G1U/20G1E/20G1A)
15
16
REMOTE 1 OUT connector
These are RS-485 serial interface connectors, used for
connecting two or more BVM/HDM-series monitors.
The IN and OUT connectors form a loop-through
connection.
Connect two monitors using a cable with D-sub 9-pin
plugs such as an RCC-5G (not supplied) as shown in
the figure on the next page.
Menu Structure
Monitor 2
REMOTE 1
REMOTE 1
IN
IN
To switch each function between on and off or
between enable and disable, change pin connections in
the following way.
ON or enabled: Short each pin and pin 9 together.
OFF or disabled: Leave each pin open.
OUT
OUT
8 CONTROL UNIT connector (female, D-sub 9pin)
Connects a monitor control unit such as the BKM-10R
using a cable with D-sub 9-pin plugs such as an RCC5G (not supplied).
The various functions and operating conditions of the
monitor can be set with on-screen menus. Menus
consist of multiple levels of sub menus. The overview
of the menu tree is described in “Menu Directories” on
pages 20 and 21.
Chapter 2 Menu
7 ISR (Interactive Status Reporting) connector
(female, D-sub 9-pin)
Connect to the ISR system.
Chapter 1 Overview
Monitor 1
Detailed information on the levels of menus is
described at the top of explanation of each menu.
Displaying the Menus
Press the MENU button.
The menu list is displayed on the screen.
Cable with D-sub 9-pin plugs (not supplied)
M E N U
p
C O N T R O L
C O L O R
6 REMOTE 2 connector (female, D-sub 9-pin)
Forms a pararell switch and controls the monitor
externally. The pin assignment and factory setting
function assigned to each pin are given below.
5
1
9
6
S E T
M
C
S
M
E
O
T
A
M
P
A
I
P R E SE T
T E M P
A D J ...
A D J ...
U P ...
O R Y C A R D ...
Y ...
T U S ...
N T E N A N C E ...
K E Y
P R O T E C T
O F F
”A
”B
”C
”D
”E
”F
”G
”H
When you select one item on the main menu, the level
1 menu corresponding to the selected item on the main
menu appears.
The adjustments and settings which can be made with
the menus are described below.
Note
On this monitor, menu settings displayed in blue
cannot be changed.
Menu List
Pin number Function
1
Set input signal channel 1 (numeric keypad
function)
2
Set input signal channel 2 (numeric keypad
function)
3
Select sync signal (SYNC button function)
4
Set the screen to monochrome, or set for
automatic switching based on the input signal
(MONO MODE button function)
5
Safe area on/off (SAFE AREA button
function)
6, 7
Not connected
8
Tally lamp on/off
9
Ground
All pin function assignments can be changed with the
REMOTE menu.
Display of the main menu level
Functions
A
CONTROL PRESET ADJ menu
Sets the preset values for the input signal contrast, brightness, chroma, and phase.
B
COLOR TEMP ADJ menu
Sets the color temperature.
C
SET UP menus
D
MEMORY CARD menu
A menu group for performing monitor setup, consisting of the following.
• INPUT CONFIGURATION menu: Sets the input channel.
• REMOTE menu: Sets the remote control functionality.
• PASSWORD menu: Sets passwords for menus.
• SYSTEM CONFIGURATION menu: Sets power-up conditions and decoder.
• ON SCREEN SET menu: Sets data about the screen display.
• ALIGNMENT menu: Used to adjust the screen convergence and geometry.
• EXTEND menu: Loads the factory default data for the board installed.
Reads and writes setting and adjustment data from/into the memory card.
Operates on data in the memory card.
E
COPY menu
Copies set-up data from other connected monitors.
F
STATUS menu
Displays the information about the monitor or options installed in the monitor.
G
MAINTENANCE menu
Menu for maintenance (typically not used).
H
KEY PROTECT
When set to ON, function buttons on the control unit (with the exception of menu
operation buttons) will be disable. When set to OFF, key protection is removed.
For information about the REMOTE menu, see “Assigning
the Remote Control Functions (SET UP 2)—REMOTE
Menu” on page 35.
17
18
1-11
1-12
Menu Structure
About menu numbers
Menu Directories
For purposes of explanation in this manual, each menu
is preceded by menu numbers. The alphabet
determines the classification of Menus on the Menu
list (Main Menu), and the numbers determine the level
and the order. These menu numbers are not shown on
the screen.
Menus consist of three to five levels. The Main Menus
displayed on the Menu List and Levels 1 and 2 are
shown below.
The first menu in Level 1
Chapter 2 Menu
Chapter 2 Menu
The CONTROL PRESET ADJ menu
All menus including those in lower levels are shown at
the top of the explanation of each Main Menu.
Main Menu
Level 1
Level 2...
CONTROL PRESET ADJ A
MANUAL [A1]
AUTO [A2]
COPY [A3]
COLOR TEMP ADJ B
MANUAL [B1]
PROBE [B2]
SET UP C
INPUT CONFIGURATION [C1]
FORMAT [C11]
SLOT NO
REMOTE [C2]
REMOTE 1 CONFIG [C21]
REMOTE 2 CONFIG [C22]
PASSWORD [C3]
ENTER PASSWORD [C31]
SYSTEM CONFIGURATION [C4]
STANDBY MODE
DEFAULT CH
ON SCREEN SET [C5]
CAPTION VISION [C51]
ANCILLARY DATA
CH NO [C52]
CH NAME [C52]
ALIGNMENT [C6]
ROTATION (1/3)
The third menu in Level 2
The fifth menu in Level 3
The fourth menu in Level 4
...
e.g. A 1 3 5 4
...
Only the menus which require explanation are
preceded by menu numbers. Thus, the menu number is
counted without menus which do not require
explanation.
...
ADDRESS Menu
... ...
...
In addition to the menus listed in the table, the
ADDRESS menu is provided. This ADDRESS menu
is used to select the monitor or the monitor group, so
that when several monitors are connected together via
serial remote ports, the control panel can select which
monitor to control.
To display or exit the ADDRESS menu, press the
ADDRESS button. The method of choosing menu
items and changing settings is the same as with the
other menus.
...
For information about the ADDRESS menu, see “Selecting
the Monitor to Control —ADDRESS Menu” on page 49.
H STATIC CONV (2/3)
...
H CV RC (3/3)
...
EXTEND MENU [C7]
19
20
ENTER PASSWORD [C71]
Basic Menu Operations
Main Menu
Level 1
Level 2...
MEMORY CARD D
SAVE [D1]
LOAD [D2]
DELETE [D3]
FORMAT [D4]
NEW NAME [D11]
COPY E
MONITOR ADDRESS [E1]
ALL [E11]
CONTROL PRESET [E12]
COLOR TEMP [E13]
SET UP [E14]
The menus are operated using the menu operation
buttons on the front panel.
INPUT
Chapter 2 Menu
Chapter 2 Menu
STATUS F
Menu Operation Buttons
STATUS (1/3) [F1]
STATUS (2/3) [F2]
STATUS (3/3) [F3]
1
2
4
5
6
7
8
9
Del
0
Ent
Menu Operation
Follow the steps described below to display the menu
and perform the adjustment or setup you wish.
1
Press the MENU button 5.
The Menu List is displayed.
2
Using the UP/DOWN buttons 6 or PHASE knob
4, move the cursor to the desired item. (Example:
select the SET UP menu by pressing the DOWN
button.)
3
1 Numeric keypad
2 Ent button
M E N U
C O N T R O L
3 Del button
C O L O R
PHASE
p
5 MENU button
UP
MENU
DOWN
ENTER
KEY PROTECT H
S E T
M
C
S
M
4 PHASE knob
MAINTENANCE G
E
O
T
A
M
P
A
I
K E Y
P R E SE T
T E M P
A D J ...
A D J ...
U P ...
O R Y C A R D ...
Y ...
T U S ...
N T E N A N C E ...
P R O T E C T
O F F
6 UP/DOWN buttons
Cursor
Menu List
7 ENTER button
The functions of the menu operation buttons are
described below.
Button
Function
5MENU button
Displays the Menus. Goes back to the
menu of the upper level (on the Main
Menu, goes back to the normal
picture).
6UP button
Moves the cursor upward. In setting
mode, increases the setting and
adjustment values.
6DOWN button
Moves the cursor downward. In setting
mode, decreases the setting and
adjustment values.
4PHASE knob
By turning this knob clockwise, the
cursor moves upward. In setting mode,
increases the setting and adjustment
values (has the same function as UP
button).
By turning this knob counterclockwise,
the cursor moves downward. In setting
mode, decreases the setting and
adjustment values (has the same
function as DOWN button).
2Ent button
7ENTER button
Executes the items selected and
settings.
3Del button
Deletes the values and characters
entered.
1Numeric keypad Enters the numerical values.
21
22
3
Press the ENTER button 7.
The Level 1 of the selected menu is displayed.
S E T
p
I N P U T
U P
C O N F I G U R A T I O N...
R E M O T E ...
P A S S W O R D ...
S
O
A
E
Y S T E M C O N F I G U R A T I O N ...
N S C R E E N S E T ...
L I G N M E N T ...
X T E N D M E N U ...
1-13
1-14
Basic Menu Operations
4
Repeat steps 2 and 3 until the desired menu is
displayed.
For more information about setting and
adjustments, see the next page.
[ ↓ ] indicates that
I N P U T
C O N F I G U R A T I O N ↑↓
F O R M A T ...
S L O T
I
Y
S
S
N T S C - 7 .5
N O
2
N P U T N O
C S E P
3L I N E S C O M
Y N C
M OD E
I N
C R E E N M O D E ...
4 : 3 - N O R
S A F E
1
B
T
M
A R E A
O F F
S C A L E ...
8 0 %
A P E R T U R E
V A LU E
O F F
1 0 0
3
Press the ENTER or Ent button.
The setting is confirmed (The item is displayed in
white text again).
Selecting from the setting list
1
Using the UP/DOWN buttons or PHASE knob, move
the cursor to the desired item in the setting list.
Selects from
various options.
Indicates that
this item has
sub-list. Thus,
you can go to
the lower level.
Enters
numerical
values.
To abort menu operation
Press the MENU button. The menu of the upper level
is displayed.
The setting or adjustment being performed is canceled,
and data loading or saving is aborted.
S C R E E N
p
MO D E
1
1
p
I
Y
S
S
C H A N N E L
N O
I
Y
S
S
2
S A F E
1
B
T
M
2
A R E A
O F F
S C A L E ...
8 0 %
A P E R T U R E
V A LU E
O F F
1 0 0
A R E A
S C A L E ...
A P E R T U R E
V A LU E
N A M E
C H A N N E L
E D I T
E D I T
C A M
V T R
C A M
V T R
N E W
N A M E
p
Press the ENTER button.
“?” is displayed in yellow. The “?” indicates the
position where character input is possible.
C H A N N E L
N E W
N A M E
N A M E
E D I T
p
N E W
?
1
B
T
M
O F F
8 0 %
O F F
0 8 5
(Continued)
24
5
Repeat steps 3 and 4 until all the characters are
entered, then press the ENTER button.
The selected characters are confirmed, and the
display returns to the menu of the previous level.
N A M E
To correct the entered character
Press the Del button on the numeric keypad. The
character on the left side of the “?”(in yellow) is
deleted.
P R O G
2
23
Press the ENTER button.
The selected character is entered.
P R O G
C A M
V T R
N T S C - 7 .5
N O
N P U T N O
C S E P
3L I N E S C O M
Y N C
M OD E
I N
C R E E N M O D E ...
4 : 3 - N O R
S A F E
p
4
C ?
C O N F I G U R A T I O N ↑↓
F O R M A T ...
N T S C - 7 .5
If you press the DOWN button or turn the PHASE
knob to the left, the characters and symbols appear
in the reverse order described above.
P R O G
0 1 C H
C O N F I G U R A T I O N ↑↓
N P U T N O
C S E P
3L I N E S C O M
Y N C
M OD E
I N
C R E E N M O D E ...
4 : 3 - N O R
Display the setting menu and set the cursor to
NEW NAME using the UP/DOWN buttons or
PHASE knob.
Select the character you wish to enter using the
UP/DOWN buttons or PHASE knob. When you
press the UP button, or turn the PHASE knob
clockwise, the characters and symbols appear in
the order shown below.
A, B, .............Y, Z, 0, 1, ...............8, 9, ( , ), :, ;, .,
-, +, /, &, CH, (space), ?
Entering characters
Using the UP/DOWN buttons or PHASE knob,
move the cursor to the desired item and press the
ENTER or Ent button.
The selected item is displayed in yellow text and
set to setting mode.
I N P U T
0 1 C H
3
Press the ENTER button.
The display returns to the menu of the upper level,
and the selected setting is executed.
S L O T
S L O T
Press the ENTER button.
The setting is confirmed (The item is displayed in
white text again).
p
2
Using the UP/DOWN buttons or PHASE knob,
move the cursor to the desired item and press the
ENTER or Ent button.
The selected item is displayed in yellow text and
set to setting mode.
F O R M A T ...
3
1 6 : 9 - N O R M
1 6 : 9 - U N D R
Selecting in yellow text
I N P U T
Set the value in one of the following three ways:
• Enter the value directly using the numeric keypad
• Select the value using the UP/DOWN buttons
• Select the value using the PHASE knob
4 : 3 - N O R M
Entering a numerical value
1
2
4 : 3 - U N D R
If “NG” or “ERROR” appears during menu operation
Press the MENU button to return to the menu in use.
Choosing one of two or more selections
Chapter 2 Menu
p
Using the UP/DOWN buttons or PHASE knob,
change the setting.
Chapter 2 Menu
0 1 C H
the menu
continues onto
next page.
[ ↑ ] indicates that
the menu is
continued from
previous page.
2
N A M E
Preset Adjustment of the Picture Level Control
Knobs — CONTROL PRESET ADJ Menu
Preset Adjustment of the Picture Level Control Knobs — CONTROL
PRESET ADJ Menu
Overview
The preliminary adjustment of contrast, brightness,
chroma, and phase are carried out with the CONTROL
PRESET ADJ menu to set the preset values to the
knobs for the above-mentioned adjustments.
Level 1
MANUAL [A1]
AUTO [A2]
COPY [A3]
Level 2
FULL FIELD CB 100
FF CB 75 (WHITE 100)
SMPTE CB
EIA CB
OTHER MONITOR [A31]
MEMORY CARD [A32]
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see “About
menu numbers” on page 19.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
[A] CONTROL PRESET ADJ menu
Select the setting method.
MANUAL: Set with the MANUAL knobs. ÷[A1]
AUTO: Set by automatic adjustment. ÷[A2]
COPY: Copy data from elsewhere. ÷[A3]
[A3] COPY menu
Select the source to be copied from.
OTHER MONITOR: Copy data from another
monitor. ÷[A31]
MEMORY CARD: Copy data from a memory card.
÷[A32]
[A31] OTHER MONITOR menu
Input the address of the monitor from which the data
will be copied. ÷ Copy is carried out.
MONITOR ADDRESS: Input the address.
[A32] MEMORY CARD menu
Select the file name. ÷ Copy is carried out.
FILE NAME: Select the file name.
Setting Lists in the CONTROL PRESET ADJ Menu
This section explains the setting lists displayed in the
menu.
Chapter 2 Menu
Structure of the CONTROL PRESET ADJ Menu [A]
Chapter 2 Menu
Preset values can be set in the following ways:
• Adjustment with the MANUAL knobs
• Automatic adjustment (An external color bar signal is
necessary.)
• Copying data from other BVM-series monitors that
have been connected via the serial remote connector,
or from data stored in monitor memory cards.
[A2] AUTO menu
Select the color bar signal to be used for automatic
adjustment. ÷Adjustment is carried out.
FULL FIELD CB 100: 100% full-field color bar
FF CB 75 (WHITE 100): 75% full-field color bar
(with 100 % white signal)
SMPTE CB: SMPTE standard color bar
EIA CB: EIA standard color
[A1] MANUAL menu
Adjust values by turning the CHROMA, BRIGHT,
CONTRAST and/or PHASE knobs. After the
adjustment, press the ENTER button to confirm the
adjusted values.
PHASE: xxxx
CHROMA: xxxx
BRIGHT: xxxx
CONTRAST: xxxx
When you want to erase characters from the screen
while adjusting manually
Press the [F1] button. The characters disappear. To
display characters, press the [F1] button again.
To reset the setting to the default
Press the corresponding MANUAL button. The
adjusted value is reset to 1000 (default).
25
26
1-15
1-16
Adjusting the Color Temperature — COLOR TEMP
ADJ Menu
Adjusting the Color Temperature — COLOR TEMP ADJ Menu
Structure of the COLOR TEMP ADJ Menu [B]
Overview
The color temperature is adjusted with the COLOR
TEMP ADJ menu. The color temperature can be set to
one of STD, COL1 or COL 2 for each channel.
Use the factory setting value or the adjusted value as
an original values to shorten the adjustment time.
Level 1
Probe Model Name
BKM-14L (no cable required)
GRASEBY
SLS 9400
MINOLTA
CA-100
PHILIPS
PM 5639
THOMA
TF6
Chapter 2 Menu
Chapter 2 Menu
• Knob adjustment
Adjust the color temperature with the bias and gain
knobs manually.
• Automatic adjustment using a probe
You can use the following probes for automatic
adjustment of color temperature. Except for the Sony
BKM-14L, a cable is required to connect the color
analyzer to the monitor.
SONY
Level 3
Level 4
Level 5
MANUAL [B1]
Color temperature adjustment can be made in the
following three ways:
Manufacturer
Level 2
PROBE [B2]
COPY [B3]
SONY BKM-14L [B21]
GRASEBY SLS9400
MINOLTA CA-100
PHILIPS PM5639
THOMA TF6
OTHER VALUE [B31]
OTHER
MONITOR [B32]
For more information about the cable specification required
and about the connection, see “Connection Cable
Specifications for Color Temperature Probes” on page
54.
• Copying other data
Copying data from other BVM-series monitors that
have been connected via the serial remote connector,
or from data stored in monitor memory cards.
MEMORY CARD [B33]
TRIM [B4]
ADJUST [B211]
ANALYZE [B212]
START [B213]
X
Y
LOWLIGHT (20 IRE)
HIGHLIGHT (100IRE)
D65
D93
START [B2111]
SET PROBE
X
ON CRT
Y
LOWLIGHT (20 IRE)
HIGHLIGHT (100IRE)
D65
D93
SET PROBE
ON THIS CRT [B2121]
SET PROBE
ON CRT
STD
COL1
COL2
D65
D93
MONITOR
ADDRESS [B321]
FILE NAME [B331]
STD
COL1
COL2
STD
COL1
COL2
ADJUST
TRIM
SIGNAL
The lower levels of GRASEBY SLS9400, MINOLTA CA-100, PHILIPS PM5639 and THOMA TF6 are the
same as [B213] in level 3 and lower than that.
27
28
Adjusting the Color Temperature — COLOR TEMP ADJ Menu
Setting Lists in the COLOR TEMP ADJ Menu
This section explains the setting lists displayed in the
menu.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
[B] COLOR TEMP ADJ menu (STD/COL1/
COL2)
Select the adjustment method.
MANUAL: Set with the MANUAL knob. ÷[B1]
PROBE: Set using a probe. ÷[B2]
COPY: Copy data from elsewhere. ÷[B3]
TRIM: Perform fine adjustments after setting the
color temperature. ÷[B4]
[B1] MANUAL menu (STD/COL1/COL2)
Adjust the gain and bias manually.
ADJUST: Adjust the gain and bias. To shift between
gain adjustment and bias adjustment, press UP/
DOWN buttons. Use appropriate knobs in each
adjustment as described below. After the
adjustment, press the ENTER button to confirm the
adjusted values.
RED: CONTRAST knob (Adjust the R gain or
bias with the CONTRAST knob.)
GREEN: BRIGHT knob (Adjust the G gain or
bias with the BRIGHT knob.)
BLUE: CHROMA knob (Adjust the B gain or bias
with the CHROMA knob.)
LUMINANCE: PHASE knob (Adjust luminance
with the PHASE knob.)
To reset RED/GREEN/BLUE to the value
before adjustment
When you are adjusting the gain or bias using the
MANUAL adjustment knobs, you can reset the
setting to the one before adjustment by pressing the
corresponding MANUAL button.
To reset all of settings at the same time, press the
PHASE button.
To access the MANUAL menu directly
When the [F2] button is assigned as the short-cut
key to the MANUAL menu, you can directly
access the MANUAL menu that corresponds to the
color temperature setting set to the image on the
screen.
Chapter 2 Menu
For more information about the menu number, see “About
menu numbers” on page 19.
ORIGINAL VALUE: Set the initial value.
STD: Use common data (factory setting: D93).
COL1: Use common data (factory setting: D65).
COL2: Use common data (factory setting: D93).
SIGNAL: Select the white signal to be used for
adjustment.
INT: Use an internal signal. Simultaneously with
the adjustment of the gain and bias, the 100
IRE and 20 IRE signals are automatically
switched.
EXT: Use an external input signal. When adjusting
the gain and bias, input the proper signal.
Chapter 2 Menu
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
Note
You cannot reset the setting after you press the
ENTER button.
[B13] COPY SOURCE menu (STD/COL1/COL2)
Select the adjustment method and the source to be
copied from.
OTHER VALUE: Copy data from one of STD, COL
1 or COL 2. ÷[B31]
OTHER MONITOR: Copy data from another
monitor. ÷[B32]
MEMORY CARD: Copy data from a memory card.
÷[B33]
SIGNAL: Select the white signal to be used for
adjustment.
INT: Use an internal signal. Simultaneously with
the adjustment of the gain and bias, the 100
IRE and 20 IRE signals are automatically
switched.
EXT: Use an external input signal. When adjusting
the gain and bias, input the proper signal.
[B4] TRIM menu (STD/COL1/COL2)
Trim the original setting by selecting ADJUST.
ADJUST: Adjust the gain and bias. To shift between
gain adjustment and bias adjustment, press UP/
DOWN buttons. Use appropriate knobs in each
adjustment as described below. After the
adjustment, press the ENTER button to confirm the
adjusted values.
RED: CONTRAST knob (Adjust the R gain or
bias with the CONTRAST knob.)
GREEN: BRIGHT knob (Adjust the G gain or
bias with the BRIGHT knob.)
BLUE: CHROMA knob (Adjust the B gain or bias
with the CHROMA knob.)
LUMINANCE: PHASE knob (Adjust luminance
with the PHASE knob.)
Even if NOT APPLY of the TRIM item is selected,
pressing the ENTER button to confirm the adjusted
values results in that APPLY will be selected.
For details of how to assign the short-cut key, see
“Setting the Power-Up Conditions (SET UP 4) SYSTEM CONFIGURATION Menu” on page 39.
[B2] PROBE menu(STD/COL1/COL2)
Select the probe for color temperature adjustment.
SONY
BKM-14L...: Use the BKM-14L.
÷[B21]
GRASEBY SLS 9400...: Use the SLS 9400.
÷[B213]
MINOLTA CA-100...: Use the CA-100. ÷[B213]
PHILIPS
PM 5639...: Use the PM 5639.
÷[B213]
THOMA
TF6...: Use the TF6. ÷[B213]
• If you cannot execute an ADJUST or ANALYZE
menu operation when using the Sony BKM-14L
probe, try again after disconnecting and reconnecting
the probe.
• When using the Thoma TF6 probe, set the TF6
PRINT menu to off.
29
To reset RED/GREEN/BLUE to the value
before adjustment
When you are adjusting the gain or bias using the
MANUAL adjustment knobs, you can reset the
setting to the one before adjustment by pressing the
corresponding MANUAL button.
To reset all of settings at the same time, press the
PHASE button.
TRIM: Select whether to add the fine adjustment to
the original setting (gain and bias set in MANUAL
menu [B1]).
APPLY: Adds the fine adjustment to the original
setting.
When APPLY is selected, “XX/TRIM”
(XX: the selected color temperature among
STD, COL 1 or COL 2) appears on the left
top on the COLOR TEMP ADJ menu.
NOT APPLY: Reset the setting to the original
setting (gain and bias set in MANUAL menu
[B1]).
30
Note
[B21] PROBE menu (STD/COL1/COL2)
Select the BKM-14L operation.
ADJUST: Perform automatic color temperature
adjustment. ÷[B211]
ANALYZE: Display readout values on the screen.
÷[B212]
[B31] OTHER VALUE menu (STD/COL1/
COL2)
Select STD, COL1,or COL2. ÷ Copy is carried out.
STD: Copy common data (factory setting: D93).
COL1: Copy common data (factory setting: D65).
COL2: Copy common data (factory setting: D93).
D65: Copy the color temperature of D65.
D93: Copy the color temperature of D93.
[B32] OTHER MONITOR menu (STD/COL1/
COL2)
Specify the address number of the monitor.
MONITOR ADDRESS: Input the address number of
the monitor from which the data will be copied.
÷[B321]
[B33] MEMORY CARD menu
Select the file name. ÷[B331]
FILE NAME: Select the file name.
1-17
1-18
Setting the Input Configuration (SET UP 1) —
INPUT CONFIGURATION Menu
[B212] ANALYZE menu (STD/COL1/COL2)
The following message appears. Perform operation
according to the message to enable the BKM-14L to
read the color system and luminace value.
[B2111] COLOR TEMP ADJ menu
(STD/COL1/COL2)
The following message appears. Perform operation
according to the message to start adjustment.
Overview
SET PROBE ON CRT
PRESS ENTER
Adjustment starts when the probe is placed against the
center of the screen and the ENTER button is pressed.
[B2121] ANALYZE menu
(STD/COL1/COL2)
Display color temperature and luminance readout
values from the BKM-14L.
X: xxxx: Display the x coordiate of the color system.
Y: xxxx: Display the y coordiate of the color system.
L: xxxx: Display the luminance value.
Chapter 2 Menu
START: Start adjustment. ÷[B2111]
X: Enter the x coordinate.
Y: Enter the y coordinate.
LOW LIGHT (20IRE): Enter the luminance (cd/m2)
for low light.
HIGH LIGHT (100IRE): Enter the luminance (cd/
m2) for high light.
D65: Use D65 setting.
D93: Use D93 setting.
[B331] FILE NAME menu (STD/COL1/COL2)
Select STD, COL1, or COL2 of the memory card data.
÷ Copy is carried out.
STD: Copy common data (factory setting: D93).
COL1: Copy common data (factory setting: D65).
COL2: Copy common data (factory setting: D93).
Chapter 2 Menu
[B211] ADJUST menu (STD/COL1/COL2)
To start adjustment, proceed as follows.
When you use the previously adjusted values for
adjustment, you can make start adjustment by selecting
START without perform operations step (1) and step
(2).
(1) Select either D65 or D93.
Rather than selecting D65 or D93, you may instead
enter the values of the CIE 1931 color system x
and y coordinates.
(2) Enter values for LOWLIGHT and HIGHLIGHT.
(3) Select START.
Data pertaining to the input signals are set with the
INPUT CONFIGURATION menu.
When a channel number (1 to 90) is entered with the
numeric keypad, it is then possible to set which input
connector on the rear panel will be assigned to that
channel number, and select the type of signal that will
be connected. The channel numbers from 91 to 99 are
assigned to internal signals.
091: PLUGE signal (Picture Line Up Generating
Equipment)
092: 20% gray signal
093: 100% white signal
094: five-step gray scale signal
095: cross hatch signal
096: cross hatch signal
097: dot signal
098: cross hatch signal
099: 0% black signal
Attach the BKM-14L on the center of the CRT and
press the ENTER button. ÷[B2121]
Once the BKM-14L has carried out calibration, the
BKM-14L can start analyze the monitor’s
performance.
Level 1
[B321] MONITOR ADDRESS menu (STD/COL1/
COL2)
Select STD, COL1 or COL2. ÷ Copy is carried out.
STD: Copy common data (factory setting: D93).
COL1: Copy common data (factory setting: D65).
COL2: Copy common data (factory setting: D93).
31
Set which input connector on which slot will be
assigned to the current channel. The slots are
numbered from the left, as seen when facing the rear
panel, with the REMOTE connectors slot being
number 1, the input option slots number 2, and the
analog input connectors slot being number 6. The
connectors are numbered 1 to 6 (from the top) for the
slot.
Assigning the signal type and format
The signal type and format which can be assigned to
each channel number vary, depending on what
adaptors (not supplied) are installed in the rear panel.
Structure of the INPUT CONFIGURATION Menu [C1]
INPUT CONFIGURATION [C1]
REMOTE [C2]
PASSWORD [C3]
SYSTEM CONFIGURATION [C4]
ON SCREEN SET [C5]
ALIGNMENT [C6]
EXTEND MENU [C7]
SET PROBE ON THIS CRT
PRESS ENTER
Assigning slot and connector numbers
32
Level 2
FORMAT [C11]
SLOT NO
INPUT NO
YC SEP [C12]
SYNC MODE
SCREEN MODE [C13]
SAFE AREA
SCALE [C14]
APERTURE
VALUE
FILTER
CHANNEL NAME [C15]
COLOR TEMP
H PHASE
SAD H POSITION
COPY [C16]
Level 3
COMPOSITE [C111]
YC [C112]
COMPONENT [C113]
SDI [C114]
4:3 NORM
4:3 - UNDR
16:9- NORM
16:9 UNDR
80
90
100
16:9 - 80
16:9 - 90
16:9 - 100
4 : 3 - 80
4 : 3 - 90
4 : 3 - 100
PROG
EDIT
CAM
VTR
NEW NAME
OTHER CH
OTHER MONITOR [C161]
MEMORY CARD [C162]
Level 4
NTSC
PAL
PAL-M
SECAM
AUTO
NTSC
PAL
PAL-M
AUTO
YUV SMPTE/EBU-N10
YUV BETACAM
RGB
NTSC
PAL
4:2:2
AUTO
MONITOR ADDRESS
FILE NAME
Setting the Input Configuration (SET UP 1) — INPUT CONFIGURATION Menu
Setting Lists in the INPUT CONFIGURATION Menu
This section explains the setting lists displayed in the
menu.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
[C1] INPUT CONFIGURATION menu (1/2)
Set input signal data for each channel.
xxCH: Current channel is indicated. To change the
channel, enter a channel number with the numeric
keypad. The settings below will be stored as
information about the signal to be connected to this
channel.
FORMAT: Select the input signal type. ÷[C11]
SLOT NO: Enter the slot number.
INPUT NO: Enter the input connector number.
YC SEP: Select Y/C separation filter. ÷[C12]
SYNC MODE: Select the sync signal.
INT: Use an internal sync signal.
EXT: Use an external sync signal.
SCREEN MODE: Select the scan size. ÷[C13]
SAFE AREA: Choose whether or not to display the
safe area (OFF or ON).
SAFE AREA SCALE: Select the modes for safe area.
÷[C14]
APERTURE: Choose whether to use aperture
adjustment or not (OFF or ON).
APERTURE VALUE: Enter the aperture adjustment
value (0 to 200).
[C1] INPUT CONFIGURATION menu (2/2)
Set input signal data for each channel.
xxCH: Current channel is indicated. To change the
channel, enter a channel number with the numeric
keypad. The settings below will be stored as
information about the signal to be connected to this
channel.
FILTER: Switch the filter operation (OFF or ON)
when the monochrome display is selected.
CHANNEL NAME: Give the channel a name.
÷ [C15]
Note
For H PHASE and SAD H POSITION data, if values
above or below the allowable range are entered, the
monitor will not operate correctly.
[C11] FORMAT menu (xxCH)
Select the signal format.
COMPOSITE: Composite signal ÷ [C111]
YC: Y/C signal ÷ [C112]
COMPONENT: Component or RGB signal
÷ [C113]
SDI: Serial digital signal ÷ [C114]
Note
If there is no input connector or decoder corresponding
to a format, that format will not be selectable (the
cursor will skip over that item).
[C12] YC SEP menu
Select a Y/C separation filter.
TRAP/BPF: Select TRAP/BPF filter.
2 LINES COMB: Select 2 LINES COMB filter.
3 LINES COMB: Select 3 LINES COMB filter.
[C13] SCREEN MODE menu (xxCH)
Select the scan size.
4:3-NORM: Overscanned 4:3 aspect ratio. (when not
using 16:9 mask)
4:3-UNDR: Underscanned 4:3 aspect ratio. (when not
using 16:9 mask)
16:9-NORM: Overscanned 16:9 aspect ratio.
16:9-UNDR: Underscanned 16:9 aspect ratio.
[C14] SAFE AREA SCALE
Select the setting for each items of SAFE AREA
setting list.
80: Displays a 80% safe area in 4:3 screen.
90: Displays a 90% safe area in 4:3 screen.
100: Displays an 100% safe area in 4:3 screen.
16:9-80: Displays a 80% of 16:9 aspect ratio safe area
in 4:3 screen.
33
Chapter 2 Menu
For more information about the menu number, see “About
menu numbers” on page 19.
Chapter 2 Menu
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
COLOR TEMP: Set the color temperature. Select
STD, COL1 or COL2.
STD: Use common data (factory setting: D93).
COL1: Use common data (factory setting: D65).
COL2: Use common data (factory setting: D93).
H PHASE: Set the horizontal picture position (–128 to
+127).
SAD H POSITION: Adjust the horizontal display
position of the safety area (–128 to +127).
COPY: Select a method for copying data from
elsewhere. ÷[C16]
16:9-90: Displays a 90% s16:9 aspect ratio safe area in
4:3 screen.
16:9-100: Displays an 100% 16:9 aspect ratio safe
area in 4:3 screen.
4:3-80: Displays a 80% 4:3 aspect ratio safe area in
16:9 screen.
4:3-90: Displays a 90% 4:3 aspect ratio safe area in
16:9 screen.
4:3-100: Displays an 100% 4:3 aspect ratio safe area
in 16:9 screen.
• If there is no input connector or decoder
corresponding to a format, that format will not be
selectable (the cursor will skip over that entry).
[C15] CHANNEL NAME menu (xxCH)
Give the channel a name. Select a preset name, or
enter a new one.
PROG: Program signal.
EDIT: Signal from an editor.
CAM: Camera signal.
VTR: Signal from a VTR.
NEW NAME: Enter a new name. (Up to 20 characters
can be entered and up to six characters from the
head of the name are displayed in the INPUT
CONFIGURATION menu.)
1) It will take a few seconds to detect the format of an input
signal when AUTO is selected. It is recommended that a
particular format be selected if it is determined.
[C16] COPY menu (xxCH)
Select the source to be copied from.
OTHER CH: Copy data from another channel. Enter
the channel number.
When the input channel number is deleted with the
Del button, the number “1” appears instead.
Restore the previous setting by pressing the
MENU button, then re-enter the channel number.
(Setting with the UP/DOWN buttons or PHASE
knob is possible.)
OTHER MONITOR: Copy data from another
monitor. ÷[C161]
MEMORY CARD: Copy data from a memory card.
÷[C162]
[C111] COMPOSITE menu (xxCH)
Select the format of a composite signal.
NTSC: SETUP 7.5 or 0.
PAL: S (simple) or D (delay)
PAL-M: S (simple) or D (delay)
SECAM
AUTO: The format of the input signal is detected and
switched automatically. 1)
1) It will take a few seconds to detect the format of an input
signal when AUTO is selected. It is recommended that a
particular format be selected if it is determined.
Notes
• Even when selecting AUTO, also select the NTSC,
PAL, or PAL-M format.
34
[C112] Y/C menu (xxCH)
Select the format of a Y/C signal.
NTSC: SETUP 7.5 or 0.
PAL: S (simple) or D (delay)
PAL-M: S (simple) or D (delay)
AUTO: The format of the input signal is detected and
switched automatically. 1)
Notes
• Even when selecting AUTO, also select the NTSC,
PAL, or PAL-M format.
• If there is no input connector or decoder
corresponding to a format, that format will not be
selectable (the cursor will skip over that entry).
[C113] COMPONENT menu (xxCH)
Select the component signal format, or RGB.
YUV SMPTE/EBU-N10
YUV BETACAM: SETUP 7.5 or 0.
RGB
[C114] SDI menu (xxCH)
Select the format of the serial digital signal 1).
NTSC: SETUP 7.5 or 0.
PAL: S (simple) or D (delay)
4:2:2
AUTO: The format of the input signal is detected and
switched automatically. 1)
1) • It will take a few seconds to detect the format of an
input signal when AUTO is selected. It is
recommended that a particular format be selected if it
is determined.
• If the serial digital signal is not properly displayed in
SDI AUTO mode, re-enter the channel number.
[C161] OTHER MONITOR menu (xxCH)
Enter the address number of the source monitor.
÷ Copy is carried out.
MONITOR ADDRESS: Enter the address number of
the monitor from which to copy data.
[C162] MEMORY CARD menu (xx CH)
Select the file name.÷ Copy is carried out.
FILE NAME: Select the file name.
1-19
1-20
Assigning the Remote Control Functions
(SET UP 2) — REMOTE Menu
Assigning the Remote Control Functions (SET UP 2) REMOTE Menu
Overview
About monitor address and group numbers
For information about the ADDRESS menu, see “Selecting
the Monitor to Control —ADDRESS Menu” on page 49.
The address number must differ from one monitor to
another. If two or more monitors have the same address
number, an operation error occurs.
Structure of the REMOTE Menu [C2]
Level 1
INPUT CONFIGURATION [C1]
REMOTE [C2]
PASSWORD [C3]
SYSTEM CONFIGURATION [C4]
ON SCREEN SET [C5]
ALIGNMENT [C6]
EXTEND MENU [C7]
Level 2
Level 3
REMOTE 1 CONFIG [C21]
REMOTE 2 CONFIG [C22]
REMOTE 2
MONITOR ADDRESS
GROUP ADDRESS
REMOTE MODE [C211]
1 PIN [C221]
2 PIN
3 PIN
4 PIN
5 PIN
6 PIN
7 PIN
8 PIN
Setting Lists of the REMOTE Menu
This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see “About
menu numbers” on page 19.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
35
Chapter 2 Menu
The monitor control units BKM-10R/11R or control
unit monitors HDM-14E5U, BVM-14E5U/14E5E/
14F5U/14F5E/14G5U/14G5E/14G5A are able to
control up to 32 monitors connected via serial remote
connector (using the REMOTE 1 connector). By
giving each monitor a monitor address and group
number, it is possible to control just a specific monitor
or monitor group.
With the REMOTE menu, each monitor can be set
with a monitor address and group number, between 1
and 99.
The ADDRESS menu is used to select a particular
monitor or group by entering a monitor number or
group number.
Chapter 2 Menu
The remote control functions are set with the
REMOTE menu. With this monitor, both serial remote
control (REMOTE 1) and parallel remote control
(REMOTE 2) are possible. It is possible to
simultaneously use the REMOTE 1, and REMOTE 2
provided with BKM-10R/11R, the integrated control
unit monitors HDM-14E5U, BVM-14E5U/14E5E/
14F5U/14F5E/14G5U/14G5E/14G5A, for control, but
commands from REMOTE 2 have priority. Therefore,
it is impossible for the control panel or REMOTE 1 to
change items set by REMOTE 2.
There is no priority order between commands from
REMOTE 1 and the BKM-10R/11R control panel; it is
possible to set APERTURE to ON from REMOTE 1
and then set it to OFF with a control panel operation.
[C2] REMOTE menu
Select the type of remote control.
REMOTE 1 CONFIG: Set the address and group
number of the monitor controlled via the
REMOTE 1 (serial remote control) connector.
÷[C21]
REMOTE 2 CONFIG: Set the pin assignments for
the REMOTE 2 (parallel remote control)
connector. ÷[C22]
REMOTE 2: Select whether parallel remote control
will be used or not (ON or OFF).
[C21] REMOTE 1 CONFIG menu
Set the monitor address and group number.
MONITOR ADDRESS: Enter a number.
GROUP ADDRESS: Enter a number.
REMOTE MODE: Select the remote mode.
÷[C211]
[C22] REMOTE 2 CONFIG
Select the REMOTE 2 connector pins for which you
want to change the function. The factory settings for
each pin are given below. ÷[C221]
1 PIN: CH01
2 PIN: CH02
3 PIN: EXT SYNC
4 PIN: MONO
5 PIN: SAFE AREA ON
6 PIN: unused
7 PIN: unused
8 PIN: TALLY
[C211] REMOTE MODE menu
Select a remote mode according to the type of
monitors connected through the REMOTE 1
connector.
When only Sony BVM-xxE/F/G or HDM-xxE series
monitors are connected: set REMOTE MODE to
0.
When a Sony BVM-xx11/16 series monitor or a
Sony PVM monitor (with BKM-103 Serial
Remote Interface Kit installed) is connected: set
REMOTE MODE to 1 and enter a number over 64
as the MONITOR ADDRESS for each connected
Sony BVM-xxE/F/G and HDM-xxE series
monitor.
36
[C221] 1-8 PIN (1/2) menu
Assign a function to the selected pin.
CH: Select a channel number. Enter the desired
channel number with the numeric keypad.
----: Set to unused.
UNDER SCAN: Set underscan on or off.
16:9: Set a 16:9 aspect ratio on or off.
H DELAY: Set the horizontal sync display on or off.
V DELAY: Set the vertical sync display on or off.
EXT SYNC: Set the synchronization to external sync
signals enabled or disabled.
APERTURE: Set the correction of frequency
characteristics enabled or disabled.
MONO: Set monochrome display on or off.
1-8 PIN (2/2) menu
Assign a function to the selected pin.
BLUE ONLY: Set the blue signal pictures display
(monochrome) on or off.
R OFF: Set cutting red beams enabled or disabled.
G OFF: Set cutting green beams enabled or disabled.
B OFF: Set cutting blue beams enabled or disabled.
SAFE AREA ON: Set the safe area display on or off.
CAPTION VISION: Set Caption Vision on or off.
TALLY: Set tally signals on or off.
DEGAUSS: Set degaussing on or off.
POWER OFF: Set the monitor power on or off.
Setting the Password (SET UP 3) — PASSWORD
Menu
Setting the Password (SET UP 3) — PASSWORD Menu
[C31] ENTER PASSWORD menu
Enter the password for the PASSWORD menu.
Choose what action to perform with the password.
CHANGE PASSWORD: Change the password.
÷[C311]
APPLY PASSWORD: Assign the password to a
menu item. ÷[C312]
Overview
A four-digit password can be specified and applied to
desired menu options to prohibit the menu settings
from being changed without permission. The password
is set with the PASSWORD menu.
A password is always assigned to the PASSWORD
menu (factory setting: 9999).
A password for a service man can be created with the
MAINTENANCE menu.
Use of the password
Structure of the PASSWORD Menu [C3]
Level 1
INPUT CONFIGURATION [C1]
REMOTE [C2]
PASSWORD [C3]
SYSTEM CONFIGURATION [C4]
ON SCREEN SET [C5]
ALIGNMENT [C6]
EXTEND MENU [C7]
Level 2
ENTER [C31]
PASSWORD
Level 3
Level 4
Level 5
CHANGE
PASSWORD [C311] ENTER
RE-ENTER
PASSWORD [C3111] PASSWORD
APPLY
CONTROL PRESET ADJ
PASSWORD [C312] COLOR TEMP ADJ
SET UP
MEMORY CARD
COPY
KEY PROTECT
Chapter 2 Menu
If the password is not entered correctly
If an incorrect password is entered, the display returns
to the menu of the previous level.
Chapter 2 Menu
The message “ENTER PASSWORD” is displayed
when an attempt is made to select a menu item for
which the password has been applied. Then, enter the
password using numeric keypad.
[C311] CHANGE PASSWORD menu
Change the password.
ENTER PASSWORD: Enter a new password.
÷[C3111]
[C312] APPLY PASSWORD menu
Choose whether or not to apply the password to each
menu.
CONTROL PRESET ADJ: Select YES or NO.
CONTROL TEMP ADJ: Select YES or NO.
SET UP: Select YES or NO.
MEMORY CARD: Select YES or NO.
COPY: Select YES or NO.
KEY PROTECT: Select YES or NO.
[C3111] ENTER PASSWORD menu
Create a new password.
RE-ENTER PASSWORD
Enter the new password again and press the
ENTER button. ÷ The password is required.
To change it, press the MENU button. ÷ Return
to the PASSWORD [C31].
Setting Lists of the PASSWORD Menu
This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
For more information about the menu number, see “About
menu numbers” on page 19.
37
38
1-21
1-22
Setting Power-Up Conditions and Decoder (SET UP 4) —
SYSTEM CONFIGURATION Menu
Setting the Channel Selection Method and Power-Up Conditions (SET UP 4)
— SYSTEM CONFIGURATION Menu
Overview
Setting Lists of the SYSTEM
CONFIGURATION Menu
The SYSTEM CONFIGURATION menu is used for
the following settings:
Main Menu
SET UP C
Level 1
INPUT CONFIGURATION [C1]
REMOTE [C2]
PASSWORD [C3]
SYSTEM CONFIGURATION [C4]
ON SCREEN SET [C5]
ALIGNMENT [C6]
EXTEND MENU [C7]
Level 2
STANDBY MODE
DEFAULT CH
DEGAUSS DELAY
RESIDUAL SC SW
ACC SW
CONT/BRT HOLD
COL TEMP SHORT-CUT
39
Chapter 2 Menu
Structure of the SYSTEM CONFIGURATION Menu [C4]
This section explains the setting lists displayed in the
menu.
Chapter 2 Menu
• Power-up condition
This menu sets the condition of the monitor when the
MAIN POWER switch on the rear panel is switched
on.
ON: Standby mode
OFF: Operation mode
• Power-up input channel
LAST: Set the channel to the channel that was
selected at the time the power was last turned off.
CH xx: Set the channel to a specific channel number.
• Time from power-up until degauss
If several monitors are turned on at the same time and
all start degaussing at the same time, there will be a
very large current draw on the power supply for a few
moments. To prevent this, the delay time between
power-up and degaussing can be set for each monitor
independently.
• Residual subcarrier detection (when using the BKM24N/25P)
It is possible to detect residual subcarrier signals from
phase change by setting the decoder adpator’s
residual subcarrier switch on.
• Auto chroma control (ACC) (when using the BKM27T)
• Setting of the contrast and brightness after adjusting
the white balance or auto adjustment of CONTROL
PRESET.
ON: The contrast and brightness are set to the value
before adjusting.
OFF: The contrast and brightness are set to the center
value (1000) after adjusting.
• Assigning shortcut to the menu to the [F2] key
Assigns the shortcut to the MANUAL menu of the
COLOR TEMP ADJ menu to the [F2] key. This
allows you to jump directly to the MANUAL menu
corresponding to the color temperature set to the
currently displayed image (STD/COL 1/COL 2).
ON: Assigns the shortcut to the MANUAL menu of
the COLOR TEMP ADJ menu.
OFF: Does not assign the shortcut to the MANUAL
menu of the COLOR TEMP ADJ menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see “About
menu numbers” on page 19.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
[C4] SYSTEM CONFIGURATION menu
Set each of the various items.
STANDBY MODE: Select the power-up condition
when the MAIN POWER switch is turned on (OFF
or ON).
DEFAULT CH: Select the power-up input channel
(LAST or CH xx).
DEGAUSS DELAY: Set the time between power-up
and the beginning of degaussing. Enter the desired
time (in seconds).
RESIDUAL SC SW: Switch the residual switch (OFF
or ON).
ACC SW: Switch the ACC switch (OFF or ON).
CONT/BRT HOLD: Select the contrast and
brightness settings to the center or adjusted value
after adjusting the white balance or auto
adjustment of CONTROL PRESET (OFF or ON).
COL TEMP SHORT-CUT: Assign the shortcut
function to the MANUAL menu of the COLOR
TEMP ADJ menu to [F2] key (OFF or ON).
40
Setting the Screen Display (SET UP 5) —
ON SCREEN SET Menu
Convergence Adjustments (SET UP 6) —
ALIGNMENT Menu
Overview
Overview
The ON SCREEN SET menu is used to select the type
of information that will be displayed on the screen and
how that information will be displayed. The types of
information that can be set are as follows.
• Caption vision
• SDI signal ancillary data blanking (when using the
BKM-20D/21D)
• Channel number and name
Main Menu
SET UP C
OFF
CAPTION 1
CAPTION 2
TEXT 1
TEXT 2
Level 1
INPUT CONFIGURATION [C1]
REMOTE [C2]
PASSWORD [C3]
SYSTEM CONFIGURATION [C4]
ON SCREEN SET [C5]
ALIGNMENT [C6]
EXTEND MENU [C7]
Level 2
ROTATION (1/3)
H STATIC CONV (2/3)
...
CAPTION VISION [C51]
ANCILLARY DATA
CH NO [C52]
CH NAME [C52]
CH NO POSITION [C53]
CH NAME POSITION [C53]
Level 3
...
INPUT CONFIGURATION [C1]
REMOTE [C2]
PASSWORD [C3]
SYSTEM CONFIGURATION [C4]
ON SCREEN SET [C5]
ALIGNMENT [C6]
EXTEND MENU [C7]
Level 2
Chapter 2 Menu
SET UP C
Level 1
Structure of the ALIGNMENT Menu [C6]
Chapter 2 Menu
Structure of the ON SCREEN SET Menu [C5]
Main Menu
The ALIGNMENT menu is used for adjusting
convergence and geometry.
H CV R C (3/3)
Setting Lists of the ALIGNMENT Menu
Setting Lists of the ON SCREEN SET Menu
This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see “About
menu numbers” on page 19.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
[C5] ON SCREEN SET menu
Select items to be displayed on the screen.
CAPTION VISION: Select the caption display mode.
÷[C51]
ANCILLARY DATA: Select whether or not to
display the ancillary data in the serial digital signal
(OFF or ON).
CH NO: Select the display mode of the channel
number. ÷[C52]
CH NAME: Select the display mode of the channel
name. ÷[C52]
CH NO POSITION: Select the display position for
the channel number. ÷[C53]
CH NAME POSITION: Select the display position
for the channel name. ÷[C53]
This section explains the setting lists displayed in the
menu.
[C51] CAPTION VISION menu
Select the caption display mode.
OFF: Not displayed
CAPTION 1: Displayed in Caption 1 mode.
CAPTION 2: Displayed in Caption 2 mode.
TEXT 1: Displayed in Text 1 mode.
TEXT 2: Displayed in Text 2 mode.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see “About
menu numbers” on page 19.
[C51] CH NO or CH NAME menu
Select the channel number and channel name display
mode.
AUTO: Disappear after displayed for a while.
ON: Displayed.
OFF: Not displayed.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
[C52] CH NO POSITION or CH NAME NAME
POSITION menu
Select the display position.
TL: Top left
TC: Top center
TR: Top right
BL: Bottom left
BC: Bottom center
BR: Bottom right
41
42
[C6] ALIGNMENT menu (1/3)
Adjust each item with the UP and DOWN buttons or
PHASE knob.
ROTATION: Compensates for the screen rotation
which occurs when the monitor is installed facing
north or south.
V SIZE: Adjust the height of the picture.
V CENTER: Adjust the vertical picture position.
H SIZE: Adjust the width of the picture.
H PHASE: Adjust the horizontal picture position.
H PIN: Correct side pincushion distortion.
H KEY: Correct trapezoid distortion.
SUB CONTRAST: Adjust the center value of the
contrast when the image size is changed.
This item can not be selected when 4:3-NORM is
selected in the SCREEN MODE menu.
1-23
1-24
Using Extended Functions (SET UP 7) — EXTEND
Menu
[C6] ALIGNMENT menu (2/3)
Adjust each item with the UP and DOWN buttons or
PHASE knob.
H STATIC CONV: Adjust horizontal static
convergence.
V STATIC CONV: Adjust vertical static
convergence.
V CONV TOP: Adjust vertical convergence at the top
of the screen.
V CONV BOTTOM: Adjust vertical convergence at
the bottom of the screen.
Overview
The following 4 functions can be executed with the
EXTEND menu.
Chapter 2 Menu
Chapter 2 Menu
Note
• Loading factory default data for installed boards into
memory.
• Writing monitor setting and adjustment data to the
monitor memory card or read setting and adjustment
data from the monitor memory card.
• Restarting the monitor.
• Automatically adjusting the setup level and 100 IRE
level of the internal white signal which is used in the
COLOR TEMP ADJ menu ([B]).
Structure of the EXTEND Menu [C7]
Items from H CONV UPPER to HCV LB are only
available for BVM-20G1U/20G1E/20G1A.
Level 1
H CONV UPPER: Adjust horizontal convergence at
the top of the screen.
H CONV LOWER: Adjust horizontal convergence at
the bottom of the screen.
Level 2
Level 3
Level 4
Level 5
INPUT CONFIGURATION [C1]
REMOTE [C2]
PASSWORD [C3]
SYSTEM CONFIGURATION [C4]
[C6] ALIGNMENT menu (3/3)
Adjust each item with the UP and DOWN buttons or
PHASE knob.
H CV R C: Adjust horizontal convergence at the
center right of the screen.
H CV R T: Adjust horizontal convergence at the top
right of the screen.
H CV R B: Adjust horizontal convergence at the
bottom right of the screen.
H CV L C: Adjust horizontal convergence at the
center left of the screen.
H CV L T: Adjust horizontal convergence at the top
left of the screen.
H CV L B: Adjust horizontal convergence at the
bottom left of the screen.
ON SCREEN SET [C5]
ALIGNMENT [C6]
EXTEND MENU [C7]
ENTER
PASSWORD
[C71]
RE-LOAD FACTORY DATA
[C711]
MEMORY CARD [C712]
SLOT 1 CONTROL
SLOT2 SDI4:2:2/4FSC1)
SLOT6 VIDEO AMP
SLOT 7 DEFLECTION
SLOT 9 POWER SUPPLY
[C7111]
Confirmation
message 2)
BACK UP SYSTEM DATA
[C7121]
Confirmation
RE-STORE SYSTEM DATA message 3)
[C7122]
RE-START MONITOR [C713]
ADJ INT SIGNAL [C714]
1) This is displayed when the BKM-21D is installed in the SLOT 2.
2) The confirmation message appears. Selecting OK results in resetting the data and automatically turning the
monitor off and on again. Selecting CANCEL results in returning to the RE-LOAD FACTORY DATA [C711]
menu.
3) The confirmation message appears. Selecting OK results reading the data from the monitor memory card.
Selecting CANCEL results in returning to the MEMORY CARD [C712] menu.
43
44
Monitor Memory Card Data Operations
— MEMORY CARD Menu
Overview
Setting Lists of the EXTEND Menu
This section explains the setting lists displayed in the
menu.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
[C713] RE-START MONITOR menu
Turn the monitor off and on again automatically.
[C714] ADJUST SIGNAL menu
Adjust the SETUP level and 100 IRE level of the
internal white signal which is used with the COLOR
TEMP ADJ menu ([B]).
[C7] EXTEND menu
Enter the password (ENTER PASSWORD [C71])
When the correct password is entered, the following
item appears.
Choose the function to execute.
RE-LOAD FACTORY DATA: Restore factory
default data for the board installed in the selected
slot. ÷[C711]
MEMORY CARD: Read and write setting and
adjustment data by using the monitor memory
card. ÷[C712]
RE-START MONITOR: Restart the monitor.
÷[C713]
ADJ INT SIGNAL SETUP: Automatically adjust the
SETUP level and 100 IRE level of internal signals.
÷[C714]
[C7111] RE-LOAD FACTORY DATA menu
The following message appears to confirm the data
reload operation.
[C711] RE-LOAD FACTORY DATA menu
Select a slot where a board is installed to reload
factory default data to the board.÷[C7111]
[C7121] BACK UP SYSTEM DATA menu
While the system is writing the data, a “–” mark blinks
at the top right of the menu. (It takes some time to save
the data.)
[C712] MEMORY CARD menu
Insert the monitor memory card into the MEMORY
CARD slot and select the operation to perform.
BACK UP SYSTEM DATA: Write the data to the
monitor memory card. ÷[C7121]
RE-STORE SYSTEM DATA: Read the data from
the monitor memory card. ÷[C7122]
Notes
• Before using a monitor memory card, it must be
formatted it with the FORMAT menu ([D4]).
SAVE [D1]
LOAD [D2]
DELETE [D3]
FORMAT [D4]
Level 2
Level 3
NEW NAME
FILE NAME
FILE NAME
FILE NAME
Confirmation message
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
Note
ALL DATA WILL BE RESTORED
ARE YOU SURE?
OK: ENTER KEY
CANCEL: MENU KEY
MEMORY CARD D
Level 1
This section explains the setting lists displayed in the
menu.
OK: To continue, press the ENTER button. ÷ Resets
the data and automatically turn the monitor off and
on again.
CANCEL: To cancel, press the MENU button. ÷
Returns to the RE-LOAD FACTORY DATA
menu. ([C711])
[C7122] RE-STORE SYSTEM DATA menu
The following message appears to confirm the data
restore operation.
Main Menu
Confirmation message
Setting Lists of the MENU CARD Menu
DATA RESET TO
ITS FACTORY SETTING
AND MONITOR WILL RESTART
ARE YOU SURE?
OK: ENTER KEY
CANCEL: MENU KEY
Slots you can select are slot 6 and slot 7 only. When
the optional board has been installed, you can also
select slot 2.
Structure of the MEMORY CARD Menu D
Chapter 2 Menu
For more information about the menu number, see “About
menu numbers” on page 19.
Operations on monitor memory card data are
performed with the MEMORY CARD menu.
Chapter 2 Menu
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
• System data and MEMORY CARD data ([D1])
cannot be stored on the same memory card. To store
memory card data, use another memory card.
• The BKM-12Y monitor memory card has a capacity
of 256 Kbytes. It can store either system data for up
to 8 monitors or 38 files of memory card data.
OK: To continue, press the ENTER button. ÷ Read
the data from the monitor memory card and
automatically turn the monitor off and on again.
CANCEL: To cancel, press the MENU button. ÷
Return to the MEMORY CARD menu ([C712]).
45
For more information about the menu number, see “About
menu numbers” on page 19.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
D MEMORY CARD menu
Select MEMORY CARD from the menu list.
CONTROL PRESET ADJ
COLOR TEMP ADJ
SET UP
MEMORY CARD ÷[D1] to [D4]
COPY
STATUS
MAINTENANCE
KEY PROTECT OFF
Select the operation to perform. (It takes some time to
load and save the data.)
SAVE: Write data to a monitor memory card. ÷[D1]
LOAD: Read data from a monitor memory card.
÷[D2]
DELETE: Delete a file. ÷[D3]
FORMAT: Format a monitor memory card. ÷[D4]
46
[D1] SAVE menu
Select the name of the file to which to write data,or
create a new file name.
NEW NAME: Enter a new name (max. 20 characters).
[D2] LOAD menu
Select the name of the file from which to read data.
[D3] DELETE menu
Select the name of the file to delete.
The following confirmation message appears.
DELETE THIS FILE?
OK: ENTER KEY
CANCEL: MENU KEY
OK: To continue, press the ENTER button. ÷ The
file is deleted.
CANCEL: To cancel, press the MENU button. ÷
Return to the level 2 of the DELETE menu [D3] (File
name list).
[D4] FORMAT menu
Confirm the format operation. The following
confirmation message appears. All files will be deleted
at formatting.
ALL FILES WILL BE DELETED!
ARE YOU SURE?
OK: ENTER KEY
CANCEL: MENU KEY
OK: To continue, press the ENTER button. ÷ The
format is performed.
CANCEL: To cancel, press the MENU button. ÷
Return to the MEMORY CARD menu ([D]).
1-25
1-26
Monitor-to-Monitor Data Copy — COPY Menu
Displaying Information About the Monitor
— STATUS Menu
Overview
Overview
When multiple monitors are connected via their serial
remote ports, data can be shared between the monitors
by data copy. The data copy from one monitor to
another is accomplished with the COPY menu.
The STATUS menu is used to view general data about
the monitor and information about signals assigned to
the slots in the rear panel.
Main Menu
COPY E
Level 1
MONITOR ADDRESS [E1]
Level 2
For more information about the menu number, see “About
menu numbers” on page 19.
• The arrow mark (÷) refers you to another setting
list that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
Main Menu
Level 1
STATUS (1/3) [F1]
STATUS (2/3) [F2]
STATUS (3/3) [F3]
Level 2
CH STATUS [F11]
SLOT STATUS [F31]
Setting Lists of the STATUS Menu
Setting Lists of the COPY Menu
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
Structure of the STATUS Menu [F]
STATUS F
ALL [E11]
CONTROL PRESET [E11]
COLOR TEMP [E11]
SET UP [E11]
This section explains the setting lists displayed in the
menu.
Chapter 2 Menu
Chapter 2 Menu
Structure of the COPY Menu E
This section explains the setting lists displayed in the
menu.
[E1] MONITOR ADDRESS menu
Select the copy source monitor.
MONITOR ADDRESS: Enter the address number.
÷[E11]
[E11] COPY menu
Select the data to be copied. ÷ Copy is carried out.
ALL: Copy data for all menu settings.
CONTROL PRESET: Copy the data for the
CONTROL PRESET ADJ menu settings.
COLOR TEMP: Copy the data for the COLOR
TEMP ADJ menu settings.
SET UP: Copy the data for the SET UP menu settings.
E COPY menu
Select COPY from the menu list.
CONTROL PRESET ADJ
COLOR TEMP ADJ
SET UP
MEMORY CARD
COPY ÷[E1]
STATUS
MAINTENANCE
KEY PROTECT OFF
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see “About
menu numbers” on page 19.
• The arrow mark (÷) refers you to another setting
list that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not
have any sub-list.
F STATUS menu
Select STATUS from the menu list.
CONTROL PRESET ADJ
COLOR TEMP ADJ
SET UP
MEMORY CARD
COPY
STATUS ÷[F1]
MAINTENANCE
KEY PROTECT OFF
[F1] STATUS menu (1/3)
Specify the channel block to be detected from channel
1 to channel 99.
47
48
[F11] CH STATUS menu
Data about the current channel is displayed.
CH: channel number
SL: slot number
IN: input connector number
FORMAT: format of the input signal
NAME: channel name
[F2] STATUS menu (2/3)
Data about the monitor is displayed.
MODEL NAME: model name
SERIAL NO: serial number
OPERATION TIME: operation time (in hours)
SOFTWARE VERSION: software version
[F3] STATUS menu (3/3)
Data about circuit boards installed into the respective
slots in the rear panel is displayed.
When the BKM-21D is installed in SLOT 2, the
following is displayed. When it is not installed,
EMPTY is displayed for SLOT 2.
SLOT1: CONTROL
SLOT2: SDI4:2:2/4FSC
SLOT6: VIDEO AMP
SLOT7: DEFLECTION
SLOT9: POWER SUPPLY
[F31] SLOT STATUS menu
Select the desired slot. Data about the optional board
installed in the selected slot is displayed.
MODEL NAME: Model name of that optional board
SERIAL NO: Serial number of that circuit board
Selecting the Monitor to Control — ADDRESS
Menu
Selecting the Monitor to Control — ADDRESS Menu
By pressing the ENTER button after selecting the item,
serial remote operation becomes activated.
Overview
A D D R ES S
S I N G L E
* *
G R O U P
* *
P O W E R
P O W E R
D I S P L A Y
O N
O FF
M O N IT O R
A D D R E SS
D I S P L A Y G R O UP A D D R E S S
S E T U P P V M ( BK M - 1 0 3 )
Press the ADDRESS button.
Chapter 2 Menu
A L L
A L L
Displaying the ADDRESS Menu
To cancel the remote control mode, press the
ADDRESS button.
A L L
Chapter 2 Menu
When multiple monitors are connected by a serial
remote connection, the ADDRESS menu is used to
choose whether one particular monitor or monitor
group will be controlled, or whether operations are to
be performed on all monitors together.
Cancelling the Remote Control
Mode
Exiting the ADDRESS Menu
To exit the ADDRESS menu, press the ADDRESS
button or the MENU button.
ADDRESS Menu
The ADDRESS button lights, and the ADDRESS
menu is displayed on the screen.
Settings made with the menu items are as follows:
Item
Function
SINGLE
Control only a specified monitor. Enter the monitor address number.
GROUP
Control only a specified monitor group. Enter the group address number.
ALL
Control all monitors.
ALL POWER ON
Turn all connected monitors on.
ALL POWER OFF
Turn all connected monitors off.
DISPLAY MONITOR ADDRESS When this item is selected, each connected monitor displays its monitor address on its
screen.
DISPLAY GROUP ADDRESS
When this item is selected, each connected monitor displays its group address on its screen.
SET UP PVM (BKM-103)
Transfer the INPUT CONFIG settings of a BVM monitor to a PVM monitor. The BKM-103
Serial Remote Interface Kit must be installed in the PVM monitor, and the monitor address
of the PVM monitor must be selected using the SINGLE menu item.
Notes
• To remotely control monitors connected in serial,
MONITOR ADDRESS or GROUP ADDRESS of
monitors should be correctly set in the REMOTE
menu.
For details of the REMOTE menu, see “Assigning the
Remote Control Functions (SET UP 2) – REMOTE Menu”
on page 35.
- In GROUP mode, when the KEY PROTECT
function is set to ON, the LED on the pressed
function button lights, but it is deactivated. (LED
of other monitors in the same group will not light.)
- In GROUP or ALL mode, the LEDs of the
function buttons will not light with controlled
from the menu. (LEDs light only when you press
the function button.)
- In GROUP or ALL mode, LEDs of controlled
monitor will light as follows.
In case of SHIFT OFF before remote control
operation: LEDs light in green when the SHIFT
button is remotely set to OFF.
In case of SHIFT ON before remote control
operation: LEDs light in orange when the SHIFT
button is remotely set to ON.
For details, see “SHIFT button” on page 12.
• In SINGLE mode, when the data is saved or load in
or from the memory card, the error message may
appear due to data communication error. In such a
case, clear the remote mode, then try again.
It is recommended to save or load data to or from the
memory card with the monitor which is free from the
remote operation.
• When Sony BVM-xxE/F and HDM-xxE series
monitors are connected together, select these
monitors for each series in SINGLE mode or GROUP
mode to remotely control them.
49
50
1-27
1-28
Specifications
Specifications
y
0.640
0.330
G
0.290
0.600
B
0.150
0.060
BVM-20G1U/20G1E/20G1A:
414 × 444 × 570 (163/8 × 173/8 ×
221/2 inches) (w/h/d)
BVM-14G1U/14G1E/14G1A:
280 × 346 × 530 (111/8 × 135/8 ×
207/8 inches) (w/h/d)
BVM-14G5U/14G5E/14G5A:
280 × 482 × 573 (111/8 × 19 ×
225/8 inches) (w/h/d)
257 (101/8)
Dimensions
x
R
51.7 (21/8)
EBU phosphor (BVM-14G1E/14G1A/
14G5E/14G5A)
414 (163/8)
0.070
399 (153/4)
0.155
15 (19/32)
B
30
(13/16)
26 (11/16)
26 (11/16)
30 (13/16)
BVM-14G1U/14G1E/14G1A
346 (135/8)
y
0.330
G
0.290
0.600
B
0.150
0.060
BVM-14G5U14G5E/14G5A
Unit: mm (inches)
BVM-14G1U/14G1E/14G1A/
14G5U/14G5E/14G5A
Aperture grille pitch: 0.25 mm
90-degree deflection, 29.4 mm
diameter in-line gun.
Effective picture size:
267 × 200 mm (10 5/8 × 7 7/8
inches) (w/h)
331 mm (13 inches) (diagonal
size)
CRT protection: EHT (extremely
high tension) protection type
BVM-20G1U/20G1E/20G1A:
approx. 36 kg
(79 lb 6 oz)
BVM-14G1U/14G1E/14G1A:
approx. 21 kg
(46 lb 5 oz)
BVM-14G5U/14G5E/14G5A:
approx. 24kg
(52 lb 15 oz)
Power consumption
BVM-20G1U/20G1E/20G1A:
125W
When an optional adaptor is
installed: 140 W
BVM-14G1U/14G1E/14G1A:
105W
When an optional adaptor is
installed: 120 W
BVM-14G5U/14G5E/14G5A:
105W
When an optional adaptor is
installed: 120 W
Power requirements
BVM-20G1U: AC100 - 120 V,
1.6 A, 50/60 Hz
BVM-20G1E/20G1A:
AC 100 - 120/220 - 240 V,
1.6/0.7 A, 50/60 Hz
BVM-14G1U/G5U:
AC 100 - 120 V, 1.3 A, 50/60 Hz
BVM-14G1E/14G1A/14G5E/
14G5A: AC 100 - 120/220 240 V, 1.3/0.6 A, 50/60 Hz
Input/output connectors
482 (19)
Video input
426 (167/8)
280 (111/2)
410 (161/4)
257 (101/8)
x
0.640
15
(19/32)
EBU phosphor (BVM-20G1E/20G1A)
R
Unit: mm (inches)
330 (13)
4 (3/16)
0.070
0.595
4 (3/16)
0.595
0.155
0.340
0.310
Unit: mm (inches)
257 (101/8)
0.310
B
0.630
G
265 (101/2)
G
R
280 (111/2)
y
0.340
SMPTE C phosphor (BVM-14G1U/
14G5U)
x
y
Chapter 3 Appendix
x
0.630
R
444 (171/2)
410 (161/4)
Chapter 3 Appendix
SMPTE C phosphor (BVM-20G1U)
BVM-20G1U/20G1E/20G1A
265 (101/2)
CRT
525 lines, 60 fields per second
interlaced
625 lines, 50 fields per second
interlaced
Super fine pitch Trinitron
BVM-20G1U/20G1E/20G1A
Aperture grille pitch: 0.3 mm
90 degree deflection, 30.6 mm
diameter in-line gun.
Effective picture size:
387 × 291 mm (15 1/4 × 83/8
inches) (w/h)
483 mm (19 inches) (diagonal
size)
CRT protection: EHT (extremely
high tension) protection type
Warm-up time: approx. 30 minutes
Anode voltage: 23 kV with no
beam current
Nominal chromaticity coordinates:
Mass
Sync input
15
(19/32)
System
Dimensional drawing
Warm-up time: approx. 30 minutes
Anode voltage: 21 kV with no
beam current
Nominal chromaticity coordinates:
General
Return loss
51
52
BNC type × 3 (with loop-through
outputs)
R/G/B 1 Vp-p ±6 dB, positive, high
impedance
Y: 1 Vp-p ±6 dB, positive, high
impedance
R-Y/B-Y: 0.7 Vp-p ±6 dB,
positive, high impedance
BNC type × 1 (with loop-through
output)
Composite sync: 0.3 to 8 Vp-p,
negative, high impedance
More than 46 dB (6 MHz, with
75-ohm termination)
Specifications
Remote control
Differential gain
Less than 5% (for luminance from
0 to 100 cd/m2)
Differential phase Less than 5° (for luminance from
0 to 100 cd/m2)
Frequency response
50 Hz to 7 MHz, +1 dB/ –3 dB
DC restoration
Back porch type
Black level fluctuation: less than
1% for 10 % to 90% APL input
signal variation.
Synchronization
Connection Cable Specifications for Color Temperature Probes
D93, D65 (adjustable to other color
temperatures)
Special cables are required to connect color
temperature probes other than the Sony BKM-14L to
the monitor.
Convergence error
Within a central area bounded by a
circle with a diameter equal to the
picture height.
BVM-20G1U/20G1E/20G1A:
Less than 0.5 mm with a central
area bounded by a circle and less
than 0.9 mm at any other point.
BVM-14G1U/14G1E/14G1A/
14G5U/14G5E/14G5A:
Less than 0.4 mm with a central
area bounded by a circle and less
than 0.8 mm at any other point.
Standard luminescence
100 cd/m2 (at standard 1 Vp-p
100% white signal)
Raster size stability
Less than 1% of picture height (at
100 cd/m2 peak luminescence, 10
to 90% APL)
Scan delay
Horizontal: Approx. 1/4 line
Vertical: Approx. 1/2 field
Resolution (at screen center, 100 cd/m2 luminescence)
800 TV lines
Modular connector
1
Underscan
Linearity
1
3
8
Signal
6
Pin Number
Signal
Pin Number
N.C.
1
1
NC
GND
2
2
NC
RXD
3
3
RTS
TXD
4
4
GND
GND
5
5
N.C.
N.C.
6
6
TXD
7
+5V
8
RXD
Connection cable for MINOLTA CA-100 probe
D-sub 25-pin connector
(male)
Environmental conditions
1
Operating temperature
0°C to 35°C (32°F to 95°F)
Optimum operating temperature
20°C to 30°C (68°F to 86°F)
Operating humidity
0% to 90% (no condensation)
Mini DIN 8-pin connector
(male)
13
2
1
5
14
Signal
Accessories supplied
5% overscan of CRT effective
screen area (adjustable range
greater than ±15%)
3% underscan of CRT effective
screen area (adjustable range
greater than ±15%)
Within a central area bounded by a
circle with a diameter equal to the
picture height, less than 1% of the
picture height, and outside the
same area, about 2% of the
picture height
6
2
Picture performance
Normal scan
Mini DIN 8-pin connector
(male)
5
AFC time constant
2 ms
Line pull range/line hold range
Greater than ±500 Hz
Vertical blanking time
Less than 1 ms
Horizontal blanking time
Less than 10 µs.
The following diagrams show specifications and pin
assignments for the required cables.
Connection cable for GRASEBY SLS 9400 probe
Chapter 3 Appendix
Video signal
Color temperature
Chapter 3 Appendix
OPTION:
Mini-DIN 8-pin × 1
CONTROL UNIT:
D-sub 9-pin × 1
REMOTE 1:
D-sub 9-pin × 1 (with loopthrough output), RS-485 serial
interface
REMOTE 2:
D-sub 9-pin × 1
ISR:
D-sub 9-pin × 1
AC power cord (1)
Cord stopper (1)
Tally plate (1)
Operation manual (1)
Design and specifications are subject to change
without notice.
53
54
25
Pin Number
3
8
Signal
6
Pin Number
N.C.
1
1
NC
TXD
2
2
NC
RXD
3
3
RTS
RTS
4
4
GND
CTS
5
5
N.C.
N.C.
6
6
TXD
GND
7
7
+5V
N.C.
8 to 25
8
RXD
1-29
1-30
The material contained in this manual consists of
information that is the property of Sony Corporation and is
intended solely for use by the purchasers of the equipment
described in this manual.
Sony Corporation expressly prohibits the duplication of any
portion of this manual or the use thereof for any purpose
other than the operation or maintenance of the equipment
described in this manual without the express written
permission of Sony Corporation.
Connection cable for PHILIPS PM 5639 probe (corresponds to PHILIPS PM 5639/64
cable)
Modular connector
1
Mini DIN 8-pin connector
(male)
6
2
1
5
3
8
6
Signal
Pin Number
+5V
1
1
NC
N.C.
2
2
NC
RXD
3
3
RTS
TXD
4
4
GND
N.C.
5
5
N.C.
GND
6
6
TXD
7
+5V
8
RXD
Signal
Pin Number
Chapter 3 Appendix
Connection cable for THOMA TF6 probe
D-sub 15-pin connector (female)
1
Mini DIN 8-pin connector (male)
8
2
1
5
9
15
3
8
6
Signal
Pin Number
N.C.
1
1
NC
RXD
2
2
NC
TXD
3
3
RTS
N.C.
4
4
GND
N.C.
5
5
N.C.
N.C.
6
6
TXD
GND
7
7
+5V
N.C.
8 to 15
8
RXD
Signal
Pin Number
55
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation et
sont destinées exclusivement à l’usage des acquéreurs de
l’équipement décrit dans ce manuel.
Sony Corporation interdit formellement la copie de quelque
partie que ce soit de ce manuel ou son emploi pour tout
autre but que des opérations ou entretiens de l’équipement
à moins d’une permission écrite de Sony Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind,
und ausschließlich zum Gebrauch durch den Käufer der in
dieser Anleitung beschriebenen Ausrüstung bestimmt sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als die
Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche schriftliche
Erlaubnis der Sony Corporation.
• BKM-10R
Overview
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the
appliance.
For customers in the USA
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to
correct the interference at his own expense.
The BKM-10R Monitor Control Unit is a control unit
for Sony BVM-series color video monitors. Use it to
power monitors on and off, perform menu operations,
and carry out monitor setup and adjustment.
Controlling monitor groups
You can control up to 32 monitors from the BKM10R. First, using the monitor menus, assign an address
number to each monitor, divide the monitors into
groups, and assign a group number to each group.
Then you can use the BKM-10R to control individual
monitors or monitor groups simply by entering
monitor address or group numbers. You can also
execute the same operation on all connected monitors,
or use the BKM-10R to put all connected monitors into
the same setup and adjustment state.
Attach to 20-inch monitors
You can use an optional BKM-32H Monitor Control
Unit Attachment Kit to attach the BKM-10R to the
BVM-20F1U/20F1E and other BVM-series color
video monitors.
Rack Mounting
You can use an supplied rack mount attachment
screws and an optional MB-510 Rack Mount Kit to
mount the BKM-10R in an EIA standard 19-inch rack.
Location and Function of Parts
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
1 Monitor memory card insertion slot
5 POWER switch
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with
the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.
For customers in Canada
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Setup and adjustment with the monitor
memory card
You can use an optional BKM-12Y Monitor Memory
Card to save and load monitor setup and adjustment
data. If your system includes more than one monitor,
you can use the monitor memory cards to exchange
data between monitors. This makes it easy to put all
monitors in your system into the same setup and
adjustment state.
6 DEGAUSS button
7 DISPLAY UNIT
connector (rear)
2 SHIFT button
3 Function buttons
8 Numeric keypad
4 Menu operation
buttons
9 MANUAL adjustment
buttons and knobs
Pour les utilisateurs au Canada
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
1 Monitor memory card insertion slot
Insert an optional BKM-12Y Monitor Memory Card.
2 SHIFT button
Each of the Function buttons 3 has a Shift On
function as well as a Shift Off function. Press this
button to select Shift On or Shift Off functions.
Each time you press this button, its orange LED lights
(Shift On) or goes out (Shift Off).
2(E)
2(E)
Shift On: Use the function indicated below the
Function button.
Shift Off: Use the function indicated above the
Function button.
1-31
1-32
Location and Function of Parts
3 Function buttons
Use these buttons to control the operation of the
monitor.
Each of these buttons has a Shift On function,
indicated below the button, as well as a Shift Off
function, indicated above the button. Press the SHIFT
button 2 to select the desired function.
Each time you press one of these buttons, its LED
lights or goes out and the function of the button
selected with the SHIFT button 2 is turned on or off.
The LED color change whether you select Shift Off
functions or Shift On functions.
For Shift Off functions: Green LED
For Shift On functions: Orange LED
Shift On functions (orange LED)
16:9: Turn to the button on to select a 16:9 aspect ratio. The
aspect ratio is 4:3 when the button is off.
SYNC: Turn the button on to synchronize with the sync signal
input to the SYNC connector on the monitor rear panel
(EXT SYNC). When the button is off, the sync signal
included in the video signal is used (INT SYNC).
Shift Off functions (green LED)
Notes
(underscan): Turn the button on for
underscanning. The display size is reduced by
approximately 3%, so that the four corners of the
raster are visible.
• When selecting INT SYNC, use component or YC
signals including a sync signal on the Y signal, and use
RGB signals including a sync signal on the G signal.
• To monitor serial digital signals, select INT SYNC.
(horizontal delay): Turn the button on to observe
the horizontal sync near the left quarter of the
screen.
• Picture brightness is adjusted automatically for
easy observation.
• Press the button together with the vertical delay
button to display a pulse cross.
BLUE ONLY: Turn the button on to turn the red and green
signals off. The blue signal is displayed as an apparent
monochrome picture. This facilitates chroma and phase
adjustments and observation of VTR noise.
(vertical delay): Turn the button on to observe the
vertical sync signal. The picture is shifted vertically
and the vertical signal is displayed near the center
of the screen.
• Picture brightness is adjusted automatically for
easy observation.
• Press the button together with the horizontal
delay button to display a pulse cross.
MONO
APT
COMB
F1
F2
ADDRESS
MONO (monochrome): Turn the button on to display
color pictures in monochrome. When the button is
off, the monitor switches automatically between
color and monochrome mode, depending on the
presence or absence of color burst signal.
R, G, and B: Turn the button on to turn the R (red), G (green),
and B (blue) beams off.
16 : 9
SYNC
BLUE
ONLY
MONO
APT
COMB
F1
F2
ADDRESS
R
G
B
F3
F4
SAFE
AREA
SAFF AREA (safe area): Turn the button on to display the
safe area.
F3 and F4: These buttons are reserved for future use.
16 : 9
SYNC
BLUE
ONLY
R
G
B
F3
F4
SAFE
AREA
ADDRESS: Turn the button on to display the
ADDRESS menu on the monitor screen. You can
use the ADDRESS menu to set operating
parameters for monitor groups.
For details, refer to the monitor’s operation
manual.
F1 and F2: These buttons are reserved for future use.
COMB (comb filter): Turn the comb filter on and off.
This function is available when an optional
decoder adaptor such as a BKM-24N is installed.
APT (aperture): Turn the button on to perform
correction of frequency characteristics. Use the
monitor menu to select the amount of correction.
This function is available when an optional decoder
adaptor such as a BKM-24N is installed.
3(E)
4(E)
Inserting and Ejecting the Monitor Memory Card
4 Menu operation buttons
UP
MENU
DOWN
ENTER
MENU button: Press to display
monitor menus.
UP and DOWN buttons: Press to
select menu items and item
settings.
ENTER button: Press to confirm
selections and settings (the
same function with the Ent
button of the numeric keypad
8).
8 Numeric keypad
Use the numeric keypad to enter menu settings and
channel numbers for signals that you want to input to
the monitor.
2
3
Del
4
5
6
0
7
8
9
Ent
For information about the ADDRESS menu, refer to the
monitor’s operation manual.
6 DEGAUSS button
Press to manually degauss the monitor CRT. When
degaussing repeatedly, wait for 5 minutes before
pressing the button again. (The monitor CRT is
degaussed automatically each time the power is turned
on.)
7 DISPLAY UNIT connector (rear)
Connect to the CONTROL UNIT connector of a
monitor designed for use with a separate control panel
such as a BVM-20F1U/20F1E/14F1U/14F1E, using a
straight cable with D-sub 9-pin plugs (not supplied) as
shown in the figure below.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
9
DISPLAY UNIT
connector pins
Inserting the monitor memory card
Monitor memory card insertion slot
0 to 9 buttons
Ent (enter) button : Confirms a
number or character
entered (the same function
with the ENTER button of
the menu operation buttons
4).
For more information about using monitor menus, refer to
the monitor’s operation manual.
5 POWER switch
Press to power the monitor on or off. If your system
includes more than one monitor, you can use the
ADDRESS menu to power all monitors on or off at
once.
9 MANUAL adjustment buttons and knobs
Each press of one of these buttons turns the button’s
green LED on or off. When the corresponding button
is on (lit), you can rotate the knobs to adjust the
picture’s contrast, brightness (black level), chroma,
and phase. These buttons are also used to enter
adjustment values from the menus.
You can use the CONTROL PRESET ADJ menu to
set preset values for each adjustment item.
For information about the CONTROL PRESET ADJ menu,
refer to the monitor’s operation manual.
EJECT button
Monitor memory
card
Be careful not to let your hands
touch the connectors on the
front edge of the monitor
memory card.
Push the monitor memory card
in until the EJECT button
comes out.
Ejecting the monitor memory card
Note
Do not eject the monitor memory card while data is
being saved or loaded.
Notes on using a SECAM, PAL D, component, and
component digital system
• The phase of component signals cannot be adjusted.
• The phase and chroma of RGB signals cannot be
adjusted.
PHASE
adjustment
button and
knob
PHASE
CHROMA
adjustment button
and knob
BRIGHT
CONTRAST
adjustment
adjustment
button and knob button and
knob
CHROMA
BRIGHT
EJECT button
CONTRAST
Press the EJECT button to
eject the monitor memory
card.
8
9
For information about using data on the monitor memory
card, refer to the monitor’s operation manual.
Del (delete) button: Deletes a
number or character
entered.
INPUT
1
Proceed as follows to insert and eject an optional
BKM-12Y Monitor Memory Card.
MANUAL
Monitor’s
CONTROL UNIT
connector pins
This connector is used to exchange control signals and
to supply power from the monitor to the BKM-10R.
5(E)
6(E)
Take out the
monitor memory
card.
1-33
1-34
Mounting the Unit in a Rack
Specifications
To mount the BKM-10R in an EIA standard 19-inch
rack, an optional MB-510 Rack Mount Kit is required.
Proceed as follows to mount the unit in the rack.
1
Remove the four feet from the
bottom of the BKM-10R.
2
Use the rack mount attachment
screws supplied with the
BKM-10R to attach the rack
mount brackets of the optional
MB-510 Rack Mount Kit to
each side of this unit.
BKM-10R
Rack mount
bracket
3
General
Accessories supplied
Power requirements 5 V DC (supplied from the
connected monitor)
Power consumption 0.5 W
0.7 W max.
Maximum dimensions (w/h/d)
424 × 44 × 157 mm (16 3/4 ×
1 3/4 × 6 1/4 inches)
Mass
1.4 kg (3 lb 1 oz)
Operating temperature
0˚C to 40˚C (32˚F to 104˚F)
Recommended working temperature
20˚C to 30˚C (68˚F to 86˚F)
Operating humidity 0% to 90% (no condensation)
Rack mount attachment screws (4)
Operation Manual (1)
Control connectors
Rack mount
attachment
screws
DISPLAY UNIT
Screw the rack mount brackets
to the rack to mount the BKM10R in the rack. Use screws
that match the size of the
rack’s screw holes.
Rack
7(E)
8(E)
D-sub 9-pin, × 1
Accessories not supplied
BKM-12Y Monitor Memory Card
MB-510 Rack Mount Kit
Related equipment
BVM-20F1U/20F1E/14F1U/14F1E Color Video
Monitor
Design and specifications are subject to change
without notice.
SECTION 2
SERVICE INFORMATIONS
2-1. CIRCUIT BOARDS LOCATION
2-1-1. BVM-14G5A/14G5E/14G5U
P
HB
YA
HC
TA
G
YC
HA
YB
E
TB
C
BC
BK
2-1-2. BVM-14G1A/14G1E/14G1U/20G1A/20G1E/20G1U
YA
P
TA
YC
G
YB
E
TB
HD
BC
BK
C
2-1
2-1-3. BKM-10R
2-2
2-2. DISASSEMBLY
2-2-1-1. CABINET REMOVAL (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U)
5 Four screws
(Claw case screw OS)
2 Left cabinet
6 Top cabinet
1 Three screws
(Claw case screw OS)
8 Rear panel
[ Loosen four screws(+B4x20) ]
7 Insulator
4 Right cabinet
3 Three screws
(Claw case screw OS)
2-2-1-2. CABINET REMOVAL (20G1A/20G1E/20G1U)
6 Two screws
(Claw case screw OS)
1 Two screws
(Claw case screw OS)
3 Screw
(+B4x20)
2 Top cabinet
7 Left cabinet
!£ Rear panel
[ Loosen four screws(+B4x20) ]
!™ Right cabinet
4 Screw
(Claw case screw OS)
!¡ Two screws
(Claw case screw OS)
8 Screw
(+B4x20)
5 Blind cover
0 Blind cover
9 Screw
(Claw case screw OS)
2-3
2-2-2-1. FBT BLOCK ASSY REMOVAL (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U)
5 Card slot assy
6 Anode cap
4 Four screws
(+P4x8)
CN904
CN901
CN902
7 Screw
(+PS4x8)
8 FBT block assy
1 Four screws
(+P4x8)
3 Two screws
(+P4x8)
2 Handle assy
2-2-2-2. FBT BLOCK ASSY REMOVAL (20G1A/20G1E/20G1U)
4 Anode cap
3 Card slot assy
CN904
CN901
CN902
5 Screw
(+PS4x8)
1 Two screws
(+P4x8)
6 FBT block assy
2-4
2 Two screws
(+P4x8)
2-2-3. E AND G BOARDS REMOVAL AND CHECK
Note: The G board can be checked in the same way of the E board.
∗ Insert the Z board into the slot and insert the E board
into the connect on the Z board.
2 G board
[ Loosen two screws(+B4x20) ]
Z board CN905
CN903
CN902
Extension board / Cable kit
(Part No. : A-1394-806-B)
1 E board
[ Loosen two screws(+B4x20) ]
2-2-4. BC AND BK BOARDS REMOVAL AND CHECK
Note: The BC board can be checked in the same way of the BK board.
Extension board / Cable kit
(Part No. : A-1394-806-B)
Z board
CN2
CN3
CN4
CN5
Battery(CR2025)
Battery
holder
Battery removal
∗ Insert the Z board into the slot and
insert the BK board into the connect
on the Z board.
2 BC board
[ Loosen two panel stopper screws ]
1 BK board
[ Loosen two screws(+B4x20) ]
2-5
2-2-5-1. CARD SLOT ASSY REMOVAL (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U)
CN20
CN18
CN15
CN905
CN903
CN902
CN007
CN16
2 Four screws
(+P4x8)
CN2
CN3
CN6
CN4
CN5
DGC
3 Card slot assy
CN7
1 Four screws
(+P4x8)
2-2-5-2. CARD SLOT ASSY REMOVAL (20G1A/20G1E/20G1U)
CN18
CN20
CN19
CN17
2 Two screws
(+P4x8)
CN15
CN16
CN905
CN903
CN902
CN007
CN2
CN3
DGC
CN4
CN5
CN6
CN7
1 Two screws
(+P4x8)
2-6
3 Card slot assy
2-2-6. TA AND TB BOARDS REMOVAL
CN102
[ 14G1U/14G1E/14G1A/20G1U/20G1E/20G1A]
Card slot assy
2 TA board
1 Six screws
(+BVTT3x8)
6 Two screws
(+BVTT3x8)
7 TB board
4 Three screws
(+BVTT3x8)
5 T shield
3 Two screws
(+BVTT3x8)
2-2-7-1. YA, YB AND YC BOARDS REMOVAL (14G1A/14G1E/14G1U)
8 Screw
(+BVTP3x10)
9 YC insulator
4 Two claws
5 YA board
!º Screw
(+BVTP3x10)
!¡ YC board
6 pin
1 Two screws
(+B4x8)
8 pin
3 Bezel assy
6 Screw
(+BVTP3x10)
7 YB board
2 Two screws
(+B4x8)
2-7
2-2-7-1-1. BEZEL ASSY REMOVAL (14G5A/14G5E/14G5U)
1 Screw
(+BVTT4x8)
8 pin
9 pin
2 Three screws
(+PSW4x14)
16 pin
6 pin
3 Handle assy
16 pin
7 Two screws
(+B4x8)
4 Three screws
(+PSW4x14)
8 Bezel assy
6 Two screws
(+B4x8)
5 Handle assy
2-2-7-1-2. HA, HB, YA, YB AND YC BOARDS REMOVAL (14G5A/14G5E/14G5U)
!§ Screw
(+BVTP3x10)
!¶ YC insulator
!• Screw
(+BVTP3x10)
!ª YC board
9 Bezel bracket (L)
0 Three screws
(+BVTP3x12)
8 Four screws
(+BVTP3x12)
!¡ HB board
7 Screw
(+PSW3x6)
!£ YA board
!™ Two claws
1 Screw
(+PSW3x6)
2 Four screws
(+BVTP3x12)
3 Bezel bracket (R)
5 Five screws
(+BVTP3x12)
6 HA board
4 Four control knobs
2-8
!¢ Screw
(+BVTP3x10)
!∞ YB board
2-2-7-2. YA, YB AND YC BOARDS REMOVAL (20G1A/20G1E/20G1U)
1 Two screws
(+B4x8)
4 Two claws
5 YA board
8 Two screws
(+BVTP3x10)
6 pin
8 pin
9 YC board
2 Two screws
6 Screw
(+B4x8)
(+BVTP3x10)
3 Bezel assy
7 YB board
2-2-8-1. PICTURE TUBE REMOVAL (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U)
5 Deflection yoke
1 Anode cap
6 Four nuts
(B flange nut M5)
2 C board
4 DY shield
3 Neck assy
8 Picture tube
9 Picture tube shield assy
7 Two washers
(Picture tube position washer)
2-9
2-2-8-2. PICTURE TUBE REMOVAL (20G1A/20G1E/20G1U)
1 Anode cap
6 Four nuts
(B flange nut M5)
2 C board
3 Neck assy
5 Deflection yoke
4 DY shield
8 Picture tube
7 Two washers
(Picture tube position washer)
• REMOVAL OF ANODE-CAP
NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, picture tube shield or carbon painted on the picture
tube, after removing the anode.
• REMOVING PROCEDURES
c
b
a
1.
Turn up one side of the rubber cap
in the direction indicated by the arrow
a .
2.
Using a thumb pull up the rubber cap
firmly in the direction indicated by the
arrow b .
• HOW TO HANDLE AN ANODE-CAP
1.
2.
3.
Don’t hurt the surface of anode-caps with sharp shaped material!
Don’t press the rubber hardly not to hurt inside of anode-caps!
A material fitting called as shatter-hook terminal is built in the rubber.
Don’t turn the foot of rubber over hardly!
The shatter-hook terminal will stick out or hurt the rubber.
2-10
3.
When one side of the rubber cap is
separated from the anode button, the
anode-cap can be removed by turning
up the rubber cap and pulling up it in
the direction of the arrow c .
2-2-9. UPPER COVER REMOVAL (BKM-10R)
2-2-10. HA AND HB BOARD REMOVAL (BKM-10R)
2-11
2-2-11. HC BOARD REMOVAL (BKM-10R)
2-12
SECTION 3
SET-UP ADJUSTMENTS
Perform the following adjustments when replacing the CRT.
3-1. Preparations
[Required Tools and Measuring Instruments]
[Setting of INPUT CONFIGURATION Menu]
1.
2.
3.
4.
Unless specified otherwise, set the INPUT CONFIGURATION menu of the SETUP menu as follows.
FORMAT ........................... COMPONENT YUV
SMPTE/EBU N-10
SLOT NO ........................... 6
INPUT NO ......................... 1
SYNC MODE .................... INT
SCREEN MODE ............... 4:3 NORM
SAFE AREA ...................... OFF
CHANNEL NAME ............ PROG
COLOR TEMP .................. STD
H PHASE ........................... 000
Signal generator
Oscilloscope
Color analyzer (MINOLTA CA-100)
Following specified cables for connecting RS-232C pin
of CA-100 and OPTION pin of monitor.
BVM Option connector side
CA-100 RS-232C connector side
Mini DIN 8pin
D Sub 25pin
H SYNC
1
1
FG
V SYNC
2
2
TXD
RTS
3
3
RXD
GND
4
4
RTS
NC
5
5
CTS
TXD
6
6
NC
+5V
7
7
GND
RXD
8
8
NC
9 to 19
NC
20
DTR
21 to 25
NC
• CONNECT
Front Panel of BKM-10R
3-1
3-2. Focus Adjustment
3-3. Landing Adjustment
1. Input the dot signal or cross hatch signal.
2. Set the following DF adjustment data to the center value
(128).
DF T&B
DF SIDE
DF CORNER
Note: The above adjustment menu is under the E
BOARD menu of the MAINTENANCE menu.
3. Adjust the center of the screen to the optimum focus using the FOCUS 1 VR (vertical focus adjustment) and
FOCUS 2 VR (horizontal focus adjustment).
4. Input the cross hatch signal.
5. Adjust the following DF adjustment data so that the cross
hatch lines at the ends of the screen become the same
thickness as those at the center of the screen.
DF T&B
DF SIDE
DF CORNER (fixed at value)
6. Adjust the DF data in the same way in the following
modes.
4:3
UNDERSCAN mode
16:9 NORMAL SCAN mode
16:9 UNDER SCAN mode
1. Input the white signal.
2. Press the BRIGHTNESS VR and CONTRAST VR buttons to the preset condition. [ The LEDs (green) on the
buttons go off. ]
3. Face the CRT screen towards the east (west) and press
the DEGAUSS button.
4. Set the Purity knob to the mechanical center.
14-inch model
Purity control
Purity
6 poles magnet
4 poles magnet
(Fixed)
20-inch model
Purity control
Purity
6 poles magnet
Fig. 1-2
Focus 1
5. Push the DY (deflection york) to the front as much as
possible.
6. Secure the neck assembly in the position shown in Fig.
1-3.
Focus 2
20-inch model
14-inch model
Fig. 1-1
Neck assy
Neck assy
3-2
Fig. 1-3
7. Set the color of the screen to green only (Turn on the
SHIFT button (LED lights up in orange), and turn on the
R button or B button (LED lights up (on the BKM-10R).)
8. Rotate the Purity knob, and adjust so that the green comes
to the center of the screen as shown in Fig. 1-4.
3-4. H Blanking Adjustment
• Preparations
1. Connect the signal generator and input the digital
monoscope signal.
2. Increase BRIGHT until the blanking can be seen.
Note: The following adjustment menus are under the E
BOARD menu of the MAINTENANCE menu.
H CENTER
H PHASE
H BLK PHASE
H BLK WIDTH
H SIZE
Fig. 1-4
9. Move DY backwards, and adjust so that the color of the
whole screen becomes green only.
10. Adjust the tilt of DY at cross hatch signal and tighten the
screw of DY.
11. Secure the deflection york with four (20 Inch), three (14
Inch) spacers.
DY spacer
• 4:3 NORMAL SCAN Mode
1. Set the SCREEN MODE to 4:3 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Decrease the H SIZE so that the whole left and right
edges of the luster can be seen.
Write down the original H SIZE data.
3. Maximize (255) the H BLK PHASE data and Minimam
(000) the H BLK WIDHT data.
4. Adjust the H CENTER data so that the luster comes to
the center of the screen (so that A B).
Write down the H CENTER data.
5. Adjust the H PHASE data so that the monoscope screen
comes to the center of the luster (so that C D).
Write down the H PHASE data.
Effective screen
Deflection range (luster)
Signal range
Deflection youk
(For 14 inch model)
A
B
C
D
Fig. 1-5
• Final check
After adjusting, check that there is no mislanding when the
unit is faced in all four directions, north, south, east, west.
H CENTER: A B
H PHASE: C D
Fig. 1-6
3-3
6. Adjust the H BLK PHASE data and adjust so that H
Blanking is 0.25 frame outside the right edge of the
monoscope signal area. (Fig. 1-7)
Write down the H BLK PHASE data.
7. Adjust the H BLK WIDTH data and adjust so that H
Blanking is 0.25 frame out side the left edge of the
monoscope signal erea. (Fig. 1-7)
Write down the H BLK WIDTH data.
8. Set the original H SIZE data.
Signal range
H BLK
H BLK WIDTH
H BLK PHASE
Fig. 1-7
• 4:3 UNDER SCAN Mode
1. Set the SCREEN MODE to 4:3 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the H CENTER data to the same value as the 4:3
NORMAL SCAN mode.
3. Set the H PHASE data to the same value as the 4:3 NORMAL SCAN mode.
4. Adjust the H BLK PHASE data until the blanking at the
right side of the screen just disappears outside the effective screen.
5. Set the H BLK PHASE data to +30.
Write down the H BLK PHASE data.
6. Adjust the H BLK WIDTH data until the blanking at the
left side of the screen just disappears outside the effective screen.
7. Set the H BLK WIDTH data to +30.
Write down the H BLK WIDTH data.
3-4
• 16:9 NORMAL SCAN Mode
1. Set the SCREEN MODE to 16:9 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the H CENTER data to the same value as the 4:3
NORMAL SCAN mode.
3. Set the H PHASE data to the same value as the 4:3 NORMAL SCAN mode.
4. Set the H BLK PHASE data to the same value as the 4:3
NORMAL SCAN mode.
5. Set the H BLK WIDTH data to the same value as the 4:3
NORMAL SCAN mode.
• 16:9 UNDER SCAN Mode
1. Set the SCREEN MODE to 16:9 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the H CENTER data to the same value as the 4:3
UNDR SCAN mode.
3. Set the H PHASE data to the same value as the 4:3 UNDR
SCAN mode.
4. Set the H BLK PHASE data to the same value as the 4:3
UNDER SCAN mode.
5. Set the H BLK WIDTH data to the same value as the 4:3
UNDER SCAN mode.
3-5. V Blanking Adjustment
• Preparations
1. Connect the signal generator and input the monoscope
signal.
2. Increase BRIGHT until the blanking can be seen.
Note: The following adjustment menus are under the E
BOARD menu of the MAINTENANCE menu.
V BLK TOP
V BLK BOT
V BLK
• 4:3 NORMAL SCAN Mode
1. Set the SCREEN MODE to 4:3 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Adjust the V BLK TOP data until the blanking at the top
of the screen just disappears outside the effective screen.
3. Set the V BLK TOP data to +30.
Write down the V BLK TOP data.
4. Adjust the V BLK BOTTOM data until the blanking at
the bottom of the screen just disappears outside the effective screen.
5. Set the V BLK BOTTOM data to –30.
Write dwon the V BLK BOTTOM data.
6. Set the V BLK data to fixed at value (128).
• 16:9 NORMAL SCAN Mode
1. Set the SCREEN MODE to 16:9 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the V BLK TOP data to 255.
3. Set the V BLK BOTTOM data to 000.
4. Set the V BLK data to fixed at value (128).
• 16:9 UNDER SCAN Mode
1. Set the SCREEN MODE to 16:9 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the V BLK TOP data to 255.
3. Set the V BLK BOTTOM data to 000.
4. Set the V BLK data to fixed at value (128).
Fig. 1-8
• 4:3 UNDER SCAN Mode
1. Set the SCREEN MODE to 4:3 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the V BLK TOP data to 255.
3. Set the V BLK BOTTOM data to 000.
4. Set the V BLK data to fixed at value (128).
3-5
3-6. Linearity Adjustment
Note: The following adjustment menus are under the E
BOARD menu of the MAINTENANCE menu.
H PHASE
V CENTER
V SIZE
V LIN BALANCE
V LIN AMP
H SIZE
H LIN BALANCE
H LIN AMP
H KEY BAL
H KEY
H PIN BAL
H PIN
H CENTER BOW
H MID PIN
H U COR PIN
H L COR PIN
1. Input the cross hatch signal.
2. Check that the image is not tilting, and there is no top
and bottom V PIN distortion nor horizontal trapezoid
distortion.
Tilt: Adjust the DY tilt.
Top/bottom V PIN distortion: Adjust the top and bottom DY head swing
Horizontal trapezoid distortion: Adjust using the DY
TLV VR (take note
that the convergence
may be disrupted.)
3. Input the monoscope signal.
4. Set the SCREEN MODE to 4:3 NORM at the INPUT
CONFIGURATION menu.
5. Adjust the H PHASE data, and adjust the horizontal
center of the image.
6. Adjust the vertical center of the image.
7. Input the cross hatch signal.
8. Adjust the V SIZE, V LIN BALANCE, and V LIN AMP
data as shown in Fig. 1-9.
9. Adjust the H SIZE, H LIN BALANCE, and H PIN AMP
data as shown in Fig. 1-10.
3-6
V LIN BALANCE
V LIN AMP
Fig. 1-9
H LIN BALANCE
H LIN AMP
Fig. 1-10
10. Adjust the H KEY BAL, H KEY, H PIN BAL, and H
PIN data so that there is no side trapezoid distortion and
PIN distortion as shown in Fig. 1-11.
11. Adjust the H U COR PIN and H L COR PIN data as
shown in Fig. 1-12.
12. Check the H CENTER BOW and H MID PIN is very
bad should it be adjusted.
13. Repeat the above adjustment to optimize the horizontal
and vertical linearity.
14. Adjust in the same way in the following modes.
4:3
UNDER SCAN mode
16:0 NORMAL SCAN mode
16:9 UNDER SCAN mode
• Common adjusting items for modes
H CENT, H PHASE, H LIN BALANCE, H LIN AMP,
H SEZE, ROTATION, ROTATION 2.
4:3 NORM → 16:9 NORM
Copy the data
4:3 UNDR → 16:9 UNDR
• Adjusting items differing between modes
V SIZE, H PIN BAL, H PIN, H KEY BAL, H KEY,
V LIN BALANCE, V LIN AMP
H KEY
BAL
3-7. Convergence Adjustment
• Preparation
1. Set the SCREEN MODE to 4:3 NORM at the INPUT
CONFIGURATION menu.
2. Input the cross hatch signal.
3. Check that the H STATIC CONV data is the center value
(128).
Note: The H STATIC CONV adjustment menu is under
the E BOARD menu of the MAINTENANCE
menu.
4. For the 14 inch model, set the 4-pole magnet of the DY
to the OFFSET state. (See Fig. 1-2.)
5. For the 20 inch model, set the 6-pole magnet of the DY
to the OFFSET state. (See Fig. 1-2.)
H KEY
H PIN
BAL
H PIN
Fig. 1-11
Fig. 1-13
Fig. 1-12
3-7
3-7-1. Static Convergence Adjustment
• Horizontal Static Convergence
1. Adjust RV501 (H STAT) of the C board so that the red
and green dots coincide in the horizontal direction at the
screen center.
2. If the blue dot is out of convergence from the red and
green dots:
• For the 14-inch model:
Perform HMC (horizontal misconvergence) correction
using the 6-pole magnet of the DY (See Fig. 1-2.).
(The 4-pole magnet of the DY is not used. Set to the
OFFSET state.)
• For the 20-inch model:
Perform HMC (horizontal misconvergence) correction
using the 6-pole magnet of the NTC (See Fig. 1-2.).
• Vertical Static Convergence
1. Adjust the V STATIC CONV data so that the red and
green dots coincide in the vertical direction at the screen
center.
Note: The V STATIC CONV adjustment menu is under
the E BOARD menu of the MAINTENANCE
menu.
2. If the blue dot is out of convergence from the red and
green dots:
• For the 14-inch model:
Perform VMC (vertical misconvergence) correction using the 6-pole magnet of the DY (See Fig. 1-2.).
(The 4-pole magnet of the DY is not used. Set to the
OFFSET state.)
• For the 20-inch model:
Perform VMC correction using the 6-pole magnet of the
NTC (See Fig. 1-2.).
Fig. 1-14
14-inch model
Neck Assy
DY Assy
20-inch model
DY Assy
Neck Assy
Fig. 1-16
• HMC and VMC correction with 6-pole magnet
1. HMC (horizontal misconvergence) correction of 6-pole
magnet and movement of electron beam.
Fig. 1-17
2. VMC (vertical misconvergence) correction of 6-pole
magnet and movement of electron beam.
3-8
Fig. 1-15
Fig. 1-18
3-7-2. 20-inch Model Convergence Adjustment
• 4:3 NORMAL SCAN mode
1. Set the SCREEN MODE to 4:3 NORM at the INPUT
CONFIGURATION menu.
2. Input the cross hatch signal.
• Vertical Convergence Adjustment
1. Minimize the vertical misconvergence at the center of
the left side of the screen and the center of the right side
of the screen using the DY correction reactors XBV and
XCV.
* As TLV is used for adjusting the horizontal trapezoid
distortion, only when MSV is very bad should it be adjusted while maintaining the balance with the horizontal
trapezoid distortion.
2. Adjust the V STAT BOTTOM data and V STAT TOP
data so that the vertical misconvergence at the top and
bottom of the screen becomes minimum.
Note: The V STAT BOTTOM and V STAT TOP adjustment menu is under the E BOARD menu of the
MAINTENANCE menu.
XBV
• Horizontal Convergence Adjustment
1. Adjust the horizontal convergence adjustment data (H
CONV data) in the following order so that the red, green,
and blue dots coincide on the whole screen.
(Do not change the value of the H STAT data and H
STATIC CONV data (128).)
Note1: The horizontal convergence adjustment menu
is under the E BOARD menu of the MAINTENANCE menu.
Note2: In anadjustable completely using a Permalloy
correction board and fix with RTV.
1. H CONV C T
2. H CONV C B
3. H CV R C
4. H CV R T
5. H CV R B
6. H CV L C
7. H CV L T
8. H CV L B
XCV
R
R
B
B
TLV
R
B
B
R
Fig. 1-19
XCV
TLV
(RV501)
Fig. 1-21
XBV
Fig. 1-20
3-9
• 4:3 UNDER SCAN Mode
1. Set the SCREEN MODE to 4:3 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the vertical convergence adjustment data (V CONV
data) and horizontal convergence adjustment data (H
CONV data) to the same value as the 4:3 NORMAL
SCAN mode.
3. Check the horizontal and vertical convergence, and if
there is misconvergence, adjust again.
• 16:9 NORMAL SCAN Mode
1. Set the SCREEN MODE to 16:9 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the vertical convergence adjustment data (V CONV
data) and horizontal convergence adjustment data (H
CONV data) to the same value as the 4:3 NORMAL
SCAN mode.
3. Check the horizontal and vertical convergence, and if
there is misconvergence, adjust again.
• 16:9 UNDER SCAN Mode
1. Set the SCREEN MODE to 16:9 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the vertical convergence adjustment data (V CONV
data) and horizontal convergence adjustment data (H
CONV data) to the same value as the 4:3 NORMAL
SCAN mode.
3. Check the horizontal and vertical convergence, and if
there is misconvergence, adjust again.
3-7-3. 14-inch Model Convergence Adjustment
• 4:3 NORMAL SCAN mode
1. Set the SCREEN MODE to 4:3 NORM at the INPUT
CONFIGURATION menu.
2. Input the cross hatch signal.
3. Minimize the vertical misconvergence at the center of
the left side of the screen and the center of the right side
of the screen using the DY correction reactor XCV (TH).
4. Minimize the vertical misconvergence at the top and
bottom of the screen using the DY correction reactor
YCH.
* As TLV is used for adjusting the horizontal trapezed distortion, only when MSV is very bad should it be adjusted
while maintaining the balance with the horizontal trapezoid distortion.
5. Adjust the V CONV BOTTOM data and V CONV TOP
data so that the vertical misconvergence at the top and
bottom of the screen becomes minimum.
(Do not change the value of the H STATIC CONV data
(128).)
Note: The V CONV BOTTOM and V CONV TOP adjustment menus are under the E BOARD menu
of the MAINTENANCE menu.
XCV (TH)
YCH
R
B
R
B
TLV
B
R
V CONV TOP
R
G
B
R
B
R
G
B
V CONV BOTTOM
Fig. 1-22
3-10
Fig. 1-23
• 4:3 UNDER SCAN Mode
1. Set the SCREEN MODE to 4:3 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the vertical convergence adjustment data (V CONV
data) to the same value as the 4:3 NORMAL SCAN
mode.
3. Check the horizontal and vertical convergence, and if
there is misconvergence, adjust again.
• 16:9 NORMAL SCAN Mode
1. Set the SCREEN MODE to 16:9 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the vertical convergence adjustment data (V CONV
data) to the same value as the 4:3 NORMAL SCAN
mode.
3. Check the horizontal and vertical convergence, and if
there is misconvergence, adjust again.
3-8. G2 Adjustment
Note: The G2 REF Adjustment menu is under the BK
BOARD menu of the MAINTENANCE menu.
1. Input the color bar signal.
2. Connect the R, G, and B cathodes of the C board to the
probes of the oscilloscope, and check the DC voltage of
the color bar signal pedestal. (20V/Div)
3. Connect the cathode with the highest pedestal DC voltage to the probe of the oscilloscope.
4. Adjust the G2 REF data so that the pedestal DC voltage
becomes 97.0 ±3.0 V.
Pedestal
97.0 V
• 16:9 UNDER SCAN Mode
1. Set the SCREEN MODE to 16:9 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the vertical convergence adjustment data (V CONV
data) to the same value as the 4:3 NORMAL SCAN
mode.
3. Check the horizontal and vertical convergence, and if
there is misconvergence, adjust again.
DC
0V
Fig. 1-24
C Board –B SIDE–
Fig. 1-25
3-11
3-9. White Balance Adjustment
1. Outline of Adjustments and Calibration of Color Analyzer
Used for Adjustments.
Perform the following adjustments.
1.1 Creating the parameters used for converting the CRT
RGB drive voltage into color temperature coordinates.
This monitor is equipped with a function for copying
color temperature between several monitors.
Because the CRT drive voltage depends on the CRT, the
same color temperature will not be attained amongst several monitors even if the same drive voltage has been
supplied.
For this reason, to copy a color temperature between several monitors, it is necessary to send the required data
using parameters which do not depend on the CRT such
as the xyY color temperature coordinates.
Select and execute the SYSTEM/COLOR TEMP/FACTORY SET menu on the MAINTENANCE menu. The
D93 color temperature will automatically be adjusted and
at the same time, the drive voltage and color temperature coordinates conversion parameter will be created.
Use this parameter for copying the color temperature to
other monitors and for copying the color temperature to
the memory card.
Fig. 1-26
1.2 D65/D56 Color Temperature Adjustment
Perform the D56 adjustment only for BVM-14G1U/
14G5U/20G1U.
1.3 Copying Color Temperature Data D65/D93/D56 to Color
Temperature STD, COL1, COL2, AUX
3-12
Calibration of Color Analyzer
Generally, to measure the color temperature of a monitor using
several color analyzers, these color analyzers will show different values. The values measured by the color analyzer will
also change with time. For this reason, color analyzers used
for this adjustment should be calibrated first so that they will
show the correct values for the following color temperature
coordinates.
D65
D93
D56
x
y
y (cd/m2)
0.313
0.329
2.7
0.313
0.329
100
0.283
0.297
2.7
0.283
0.297
100
0.331
0.346
2.7
0.331
0.346
100
2. Adjustment Standard
2.1 Input the following signal to the G/Y input terminal of
the BK board to display it on the screen.
For BVM-14G1U/14G5U/20G1U: NTSC signal
For BVM-14G1A/14G1E/14G5A/14G5E/20G1A/
20G1E: PAL signal
2.2 Connect the RS-232C terminal of the CA-100 with the
OPTION terminal of the monitor using the cable shown
in “Required Tools and Measuring Instruments 5.”
(Refer to page 3-1).
2.3 Set the CA-100 as shown below, and connect the measuring probe of the CA-100 at the center of the CRT
screen.
Display mode : xyY mode
Baud Rate
: 9600
3. Select the SYSTEM/COLOR TEMP menu on the MAINTENANCE menu.
4. Select D93 of COLOR TEMP, cover the CRT screen with
a black cloth, select FACTORY SET, and start automatic
adjustments.
5. Select D65 of COLOR TEMP, and select the PROBE/
MINOLTA CA-100 menu. After selecting D65, cover
the CRT screen with a black cloth, and select START to
start automatic operations.
6. Execute this adjustment only for BVM-14G1U/14G5U/
20G1U.
Select AUX of COLOR TEMP, and select the PROBE/
MINOLTA CA-100 menu.
After setting X = 0.331, Y = 0.346, LOWLIGHT = 2.7,
and HIGHLIGHT = 100, cover the CRT screen with a
black cloth, and select START to start automatic operations.
7. Select the SYSTEM/COLOR TEMP/COPY/OTHER
VALUE menu on the MAINTENANCE menu.
8. Select STD of COLOR TEMP, perform the following
“D65”, and copy the color temperature data to STD.
9. Select COLOR1 of COLOR TEMP, perform the following “D93”, and copy the color temperature data to
COLOR1.
10. Select COLOR2 of COLOR TEMP, perform the following step, and copy the color temperature data to
COLOR2.
For BVM-14G1U/14G5U/20G1U: Select AUX
For BVM-14G1A/14G1E/14G5A/14G5E/20G1A/
20G1E: Select D65
11. Execute this adjustment only for BVM-14G1A/14G1E/
14G5A/14G5E/20G1A/20G1E.
Select AUX of COLOR TEMP, perform the following
“D65”, and copy the color temperature data to AUX.
3-13
SECTION 4
SAFETY RELATED ADJUSTMENTS
+B (120V) Voltage Check
High Voltage Regulator Check
Perform the following checks when replacing the following
components (marked on the schematic diagram).
Perform the following checks when replacing the following
components (marked on the schematic diagram).
G board ....... R307, R332, R333, R336, R337, R338,
IC301, IC302, PH301
E board ........ R501, R502, R503, R504, R505, R511,
IC501, IC502, IC503
1. Connect a digital voltmeter to TP303 (+120 V) and TP304
(GND) of the G board.
• Digital voltmeter: More than 4 digits
2. Input the cross hatch signal.
3. Set the BRIGHTNESS VR and CONTRAST VR buttons to the preset condition.
[ The LEDs (green) on the buttons go off. ]
4. Turn ON the power and check the TP303 (+120 V) voltage to 120.0 ±4.0 V.
1. Turn OFF the power.
2. Connect the digital voltmeter to pins 5 and 1 of CN501
on the E board.
3. Turn ON the power.
4. Input the dot signal.
5. Set the BRIGHTNESS VR and CONTRAST VR to the
minimum condition.
6. Check that the pin 5 of CN501 voltage value is within
the following range.
20-inch model: –21.8 to –23.0 V
14-inch model: –19.5 to –21.0 V
4-1
High Voltage Hold-Down Check
Perform the following checks when replacing the following
components (marked on the schematic diagram).
E board ........ R531, R532, R533, R534, R542, R543,
R544, R545, R548, IC071, IC502, IC531
P board ........ R904, R905, R906
1. Turn OFF the power.
2. Connect the digital voltmeter to the pins 5 and 1 of
CN501 on the E board.
3. Connect a 200 kΩ variable resistor between pins 2 and
1 of CN501 on the E board.
(Maximize the resistance of the 200 kΩ variable risistor.)
4. Set the BRIGHTNESS VR and CONTRAST VR to the
minimum condition.
5. Turn ON the power.
6. Input the dot signal.
7. Check that when the resistance of the 200 kΩ variable
resistor connected to pin 2 of CN501 is gradually reduced, the HV protect operated at the following values.
20-inch model: –26.4 to –30.3 V
14-inch model: –23.3 to –26.8 V
8. Turn OFF the power.
9. Disconnect the 200 kΩ variable resistor.
10. Connect the digital voltmeter to the pins 4 and 1 of
CN501 on the E board.
11. Turn ON the power.
12. Input the monoscope signal or all-white signal.
13. Set the BRIGHTNESS VR and CONTRAST VR to the
minimum condition.
14. Check that when the BRITNESS VR and CONTRAST
VR is gradually enlargement, the IK protect operated at
the following values.
Standard Value: –1.44 to –1.56 V
4-2
Beam Current Protector Check
Perform the following checks when replacing the following
components (marked on the schematic diagram).
E board ........ R571, IC501
P board ........ R901, R902, R903
BK board ..... R912, R913, IC901
1. Turn OFF the power.
2. Connect the digital voltmeter to the pins 3 and 1 of
CN501 on the E board.
3. Turn ON the power.
4. Input the all white signal or monoscope signal.
5. Set the BRIGHTNESS VR and CONTRAST VR to the
maximize condition.
6. Check the pin 3 of CN501 voltage to –0.94 to –1.05 V.
G BOARD
– A SIDE –
TP304
GND
Digital
Voltmeter
TP303
+120V
E BOARD
– A SIDE –
Digital
Voltmeter
5
1
CN501
VARIABLE RESISTOR
200kΩ
4-3
SECTION 5
CIRCUIT ADJUSTMENTS
5-1. BK Board
5-1-1. Adjustments 1
Set as follows at the INPUT CONFIGURATION menu of the SETUP menu.
FORMAT ............... COMPONENT YUV SMPTE/EBU N-10
SLOT NO ............... 6
SYNC MODE ........ INT
Select BK BOARD DATA LOAD from BK BOARD menu of MAINTENANCE menu and execute.
• Connection
Fig. 5-1
• Arrangement Diagram for Adjustment Parts
BK board –A SIDE–
1
2
3
4
5
A
6
7
TP104
TP101
B
TP102
TP304
C
D
1. Bright Center Adjustment
1. Input the component color bar signal (YUV SMPTE/
EBU N-10).
2. Set the BRIGHT data to 2048 using the BRIGHT knob.
3. Connect an oscilloscope to pin !∞ of IC701 of the BK
board.
4. As shown in Fig. 5-3, adjust the BRT CENTER data so
that the waveform becomes flat.
Note: The BRT CENTER adjustment menu is under the
BK BOARD menu of the MAINTENANCE
menu.
TP504
TP506
TP502
E
CN1
F
1
16
8
9
IC701
G
Make flat
Position of W/B insert pulse
Level difference: 0 ±8 mV
Fig. 5-2
Fig. 5-3
5-1
2. Clamp Level Adjustment
Note: The following adjustment menus are under the BK
BOARD menu of the MAINTENANCE menu.
Y CLAMP OFFSET
R–Y CLAMP OFFSET
B–Y CLAMP OFFSET
1. Input the component color bar signal (YUV SMPTE/
EBU-N10).
2. Connect the oscilloscope to TP101.
3. As shown in Fig. 5-4, adjust the Y CLAMP OFFSET
data so that the pedestal and clamp offset pulse level
becomes equal.
6. Connect the oscilloscope to TP502.
7. As shown in Fig. 5-6, adjust the B–Y CLAMP OFFSET
data so that the pedestal and clamp offset pulse level
becomes equal.
This part
Make flat
÷
Level difference: 0 ±2 mV
Fig. 5-6
This part
Make flat
÷
Level difference: 0 ±2 mV
Fig. 5-4
4. Connect the oscilloscope to TP302.
5. As shown in Fig. 5-5, adjust the R–Y CLAMP OFFSET
data so that the pedestal and clamp offset pulse level
becomes equal.
This part
Make flat
÷
Level difference: 0 ±2 mV
Fig. 5-5
5-2
5-1-2. Adjustments 2
Perform the following adjustments for each of the following
five input signals.
Set the settings required for each signal at the INPUT CONFIGURATION of the SETUP menu. When inputting the composite signal, insert the NTSC input adapter BKM-24N
(NTSC)/25P (PAL) into the empty slot of the unit.
Set as follows at the INPUT CONFIGURATION menu of
the SETUP menu.
FORMAT .............Set according to the input signal
SLOT NO .............When component signal is input: 6
When composite signal is input: Slot
no. when BKM-24N (NTSC)/25P
(PAL) is mounted.
SYNC MODE ......INT
1. COMPONENT SMPTE/EBU-N10
100% color bar signal
All white peak
700 mV
B–Y
700 mV p-p
R–Y
700 mV p-p
100 IRE all white signal
All white peak
700 mV
20 IRE all white signal
All white peak
140 mV
2. COMPONENT BETACAM SETUP 7.5
75% color bar signal
All white peak
714.29 mV
B–Y
700 mV p-p
R–Y
700 mV p-p
100 IRE all white signal
All white peak
714.29 mV
20 IRE all white signal
All white peak
142.86 mV
3. COMPONENT BETACAM SETUP 0
75% color bar signal
All white peak
714 mV
4. COMPOSITE NTSC SETUP 7.5
100% color bar signal
All white peak
714 mV
5. COMPOSITE NTSC SETUP 0
100% color bar signal
All white peak
714 mV
5-3
Configuration when Component Signal is Input
Fig. 5-7
Configuration when Composite Signal is Input
Fig. 5-8
5-4
1. Pulse Level Adjustment
Note: The following adjustment menus are under the BK
BOARD menu of the MAINTENANCE menu.
B–Y PULSE LEVEL
R–Y PULSE LEVEL
2. R–Y Gain, B–Y Gain Adjustment
Note: The following adjustment menus are under the BK
BOARD menu of the MAINTENANCE menu.
B–Y GAIN
R–Y GAIN
1. Input the color bar signal.
2. Set the CHROMA data to 1280 using the CHROMA
knob.
3. Connect the oscilloscope to TP504.
4. As shown in Fig. 5-10, adjust the B–Y PULSE LEVEL
data so that the BLUE waveform becomes flat.
Perform this adjustment only for “1. COMPONENT SMPTE/
EBU-N10”.
1. Input the color bar signal.
2. Set the CHROMA data to 1280 using the CHROMA
knob.
3. Connect the oscilloscope to TP304.
4. As shown in Fig. 5-7, adjust the R–Y GAIN data and B–
Y GAIN data so that the GREEN waveform becomes
flat.
R–Y GAIN (+)
Make flat
Make flat
Level difference: 0 ±10 mV
R–Y GAIN (+)
Fig. 5-9
5. Connect the oscilloscope to TP104.
6. As shown in Fig. 5-11, adjust the R–Y PULSE LEVEL
data so that the RED waveform becomes flat.
Level difference: 0 ±10 mV
Fig. 5-11
Make flat
Level difference: 0 ±10 mV
Fig. 5-10
5-5
3. 0% Setup Adjustment
Note: The following adjustment menus are under the BK
BOARD menu of the MAINTENANCE menu.
R SETUP
G SETUP
B SETUP
4. 100 IRE Adjustment
Note: The following adjustment menus are under the BK
BOARD menu of the MAINTENANCE menu.
R 100 IRE
G 100 IRE
B 100 IRE
1. Input only the Y signal of the color bar signal (Turn off
the R–Y signal and B–Y signal.).
2. Connect the oscilloscope to TP104.
3. As shown in Fig. 5-12, adjust the R SETUP data so that
the black level and setup signal level becomes equal.
4. Connect the oscilloscope to TP304.
5. As shown in Fig. 5-12, adjust the G SETUP data so that
the black level and setup signal level become equal.
6. Connect the oscilloscope to TP504.
7. As shown in Fig. 5-12, adjust the B SETUP data so that
the black level and setup signal level become equal.
1. Input the color bar signal.
2. Connect the oscilloscope to TP104.
3. As shown in Fig. 5-13, adjust the R 100 IRE data so that
the 100 IRE level and 100 IRE pulse level of the signal
become equal.
4. Connect the oscilloscope to TP304.
5. As shown in Fig. 5-13, adjust the G 100 IRE data so that
the 100 IRE level and 100 IRE pulse level of the signal
become equal.
6. Connect the oscilloscope to TP504.
7. As shown in Fig. 5-13, adjust the B 100 IRE data so that
the 100 IRE level and 100 IRE pulse level of the signal
become equal.
Equalize
Equalize
100 IRE
Black
Setup signal
Level difference: 0 ±2 mV
Fig. 5-12
100 IRE pulse
Level difference: 0 ±2 mV
Fig. 5-13
5-6
5. BIAS REF Adjustment
Note: The following adjustment menu is under the BK
BOARD menu of the MAINTENANCE menu.
BIAS REF
6. DRIVE REF Adjustment
Note: The following adjustment menu is under the BK
BOARD menu of the MAINTENANCE menu.
DRIVE REF
Perform this adjustment only for “1. COMPONENT SMPTE/
EBU-N10”.
Perform this adjustment only for “1. COMPONENT SMPTE/
EBU-N10”.
1. Input the 20 IRE all-white signal.
2. Connect the oscilloscope to TP506 and V period.
3. As shown in Fig. 5-14, adjust the BIAS REF data so that
the all white peak level and BIAS REF pulse level of the
signal become equal.
All-white peak: 140 mV
1. Input the 100 IRE all-white signal.
2. Connect the oscilloscope to TP506.
3. As shown in Fig. 5-15, adjust the DRIVE REF data so
that the all white peak level and DRIVE REF pulse level
of the signal become equal.
Equalize
Equalize
Level difference: 0 ±5 mV
Fig. 5-14
DRIVE REF pulse
Level difference: 0 ±5 mV
Fig. 5-15
5-7
5-1-3. Adjustments 3
Perform the following adjustments using the RGB input signals. Set as follows at the INPUT CONFIGURATION menu
of the SETUP menu.
FORMAT ............. COMPONENT RGB
SLOT NO ............. 6
SYNC MODE ...... INT
Fig. 5-16
1. RGB Signal SETUP Adjustment
Note: The following adjustment menus are under the BK
BOARD menu of the MAINTENANCE menu.
R SETUP
G SETUP
B SETUP
1. Input 100 IRE RGB signal.
2. Connect the oscilloscope to TP104.
3. Adjust the R SETUP data so that the black level and
setup signal level become equal.
4. Connect the oscilloscope to TP304.
5. Adjust the G SETUP data so that the black signal level
and setup signal level become equal.
6. Connect the oscilloscope to TP504.
7. Adjust the B SETUP data so that the black signal level
and setup signal level become equal.
5-8
Equalize
Level difference: 0 ±2 mV
Fig. 5-17
2. RGB Signal 100 IRE Adjustment
Note: The following adjustment menus are under the BK
BOARD menu of the MAINTENANCE menu.
R 100 IRE
G 100 IRE
B 100 IRE
5-1-4. White Balance Adjustment
Refer to “3. SET-UP ADJUSTMENTS (3-9. White balance
adjustment)” (Page 3-12)
1. Input the 100 IRE RGB signal.
2. Connect the oscilloscope to TP104.
3. Adjust the R 100 IRE data so that the 100 IRE level and
100 IRE pulse level of the signal become equal.
4. Connect the oscilloscope to TP304.
5. Adjust the G 100 IRE data so that the 100 IRE level and
100 IRE pulse level of the signal become equal.
6. Connect the oscilloscope to TP504.
7. Adjust the B 100 IRE data so that the 100 IRE level and
100 IRE pulse level of the signal become equal.
Equalize
Level difference: 0 ±2 mV
Fig. 5-18
5-9
5-2. BC Board
5-2-1. Adjust Preparation
Set 1CH as follows using INPUT CONFIGURATION menu of the SETUP menu.
FORMAT .................... COMPONENT YUV SMPTE/EBU N-10
SLOT NO .................... 6
SYNC MODE ............. INT
• Connection
Fig. 5-19
• Arrangement Diagram for Adjustment Parts
BC board –A SIDE–
5
6
28
15
IC108
1
14
28
15
IC107
1
14
7
1
RV101
5-2-2. D/A Level Adjustment
1. Connect the oscilloscope to pin B10 of CN1 of the BC
board.
2. Select the 93-ch menu on the MAINTENANCE menu
and output an internal white signal.
3. Adjust RV101 so that the 660 ±20 mV.
CN2
660 ±20 mV
32
Fig. 5-21
1
CN1
32
Fig. 5-20
5-10
5-2-3. SETUP Level of Built-in Signal and
100 IRE Level is Automatic operation.
1. Select the EXTEND menu of SETUP menu.
2. Select the ADJ INT SIGNAL menu and SETUP level of
built-in signal and 100 IRE level is automatic operation
and execule.
3. Displayed the PROCEDER COMPLETED is after 10 to
15 second and automatic operation is completion.
5-3. E Board
5-3-1. Adjust Preparation
Set as follows at the INPUT CONFIGURATION menu of the SETUP menu.
FORMAT ............... COMPONENT YUV SMPTE/EBU N-10
SLOT NO ............... 6
SYNC MODE ........ INT
Select E BOARD DATA LOAD from E BOARD menu of MAINTENANCE menu and execute.
• Connection
Fig. 5-22
• Arrangement Diagram for Adjustment Parts
E board –A SIDE–
1
2
A
32
B
CN802
C
5-3-2. V BLK Adjustment
1. Connect an oscilloscope to pin 9a of the E board.
2. Set the SCREEN MODE to 16:9 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
3. Adjust the V BLK data so that the V blanking pulse width
to the 520 ±30 µsec.
4. Copy the V BLK data to other mode.
Note: The V BLK adjustment menu is under the E
BOARD menu of the MAINTENANCE menu.
1
D
32
E
A
F
CN801
G
1
A = 520 ±30 µsec
Fig. 5-24
Fig. 5-23
5-11
5-3-3. H BLK Adjustment
5-3-7. Convergence Adjustment Preparation
Note: The H BLK adjustment menu is under the E BOARD
menu of the MAINTENANCE menu.
Refer to “3. SET-UP Adjustment (3-2. Focus Adjustment),
(3-3. Landing Adjustment), (3-4. H Blanking Adjustment)”
(Page 3-2 and 3-3).
1. Connect the oscilloscope to the pin 8b of CN801 on the
E board.
• 16:9 NORMAL SCAN mode
1. Set the SCREEN MODE to 16:9 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Adjust the H BLK data so that the H blanking pulse width
to the 11.5 ±0.3 µsec.
Write down the H BLK data.
• 16:9 UNDER SCAN mode
1. Set the SCREEN MODE to 16:9 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the H BLK data to the same value as the 16:9 NORMAL SCAN mode.
• 4:3 NORMAL SCAN mode
1. Set the SCREEN MODE to 4:3 NORM at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Adjust the H BLK data so that the H blanking pulse width
to the 8.0 ±0.2 µsec.
Write down the H BLK data.
• 4:3 UNDER SCAN mode
1. Set the SCREEN MODE to 4:3 UNDR at the INPUT
CONFIGURATION menu of the SETUP menu.
2. Set the H BLK data to the same value as the 4:3 NORMAL SCAN mode.
5-3-4. H Blanking Adjustment
Refer to “3. SET-UP Adjustment (3-4. H Blanking Adjustment)” (Page 3-3).
5-3-5. V Blanking Adjustment
Refer to “3. SET-UP Adjustment (3-5. V Blanking Adjustment)” (Page 3-5).
5-3-6. Linearity Adjustment
Refer to “3. SET-UP Adjustment (3-6. Linearity Adjustment)”
(Page 3-6).
5-3-8. Static Convergence Adjustment
• Horizontal Static Convergence
Adjust H STATIC CONV data so that red and green dots
match in the horizontal direction at the center of the screen.
Note: H STATIC CONV adjustment menu is under E
BOARD menu of MAINTENANCE menu.
(See Fig. 1-14)
• Vertical Static Convergence
Adjust V STATIC CONV data so that red and green dots
match in the horizontal direction at the center of the screen.
Note: V STATIC CONV adjustment menu is under E
BOARD menu of MAINTENANCE menu.
(See Fig. 1-14)
5-3-9. Convergence Adjustment 20-Inch
Model
• Preparation
Refer to “3. SET-UP Adjustment (3-7-2. 20-Inch Model
Convergence Adjustment)” (Page 3-9).
• Vertical convergence adjustment
Adjust V STATIC BOTTOM data and V STATIC TOP data
so that a vertical mis-convergence is minimized at the top
and bottom areas of the screen.
Note: V STATIC BOTTOM data and V STATIC TOP data
adjustment menu is under E BOARD menu of
MAINTENANCE menu. (See Fig. 1-20)
• Horizontal convergence adjustment
Refer to “3. SET-UP Adjustment (3-7-2. 20-Inch Model
Convergence Adjustment)” (Page 3-9).
• 4:3 UNDER SCAN mode convergence adjustment
Refer to “3. SET-UP Adjustment (3-7-2. 20-Inch Model
Convergence Adjustment)” (Page 3-9).
• 16:9 NORMAL SCAN mode convergence adjustment
Refer to “3. SET-UP Adjustment (3-7-2. 20-Inch Model
Convergence Adjustment)” (Page 3-9).
• 16:9 UNDER SCAN mode convergence adjustment
Refer to “3. SET-UP Adjustment (3-7-2. 20-Inch Model
Convergence Adjustment)” (Page 3-9).
5-12
5-3-10. Convergence Adjustment of 14-Inch
Model
• Preparation
Refer to “3. SET-UP Adjustment (3-7-3. 14-Inch Model
Convergence Adjustment)” (Page 3-10).
• Convergence adjustment
Adjust V STATIC BOTTOM data and V STATIC TOP data
so that a vertical mis-convergence is minimized at the top
and bottom areas of the screen.
Note: V STATIC BOTTOM data and V STATIC TOP data
adjustment menu is under E BOARD menu of
MAINTENANCE menu. (See Fig. 1-22)
• 4:3 UNDER SCAN mode convergence adjustment
Refer to “3. SET-UP Adjustment (3-7-3. 14-Inch Model
Convergence Adjustment)” (Page 3-10).
• 16:9 NORMAL SCAN mode convergence adjustment
Refer to “3. SET-UP Adjustment (3-7-3. 14-Inch Model
Convergence Adjustment)” (Page 3-10).
• 16:9 UNDER SCAN mode convergence adjustment
Refer to “3. SET-UP Adjustment (3-7-3. 14-Inch Model
Convergence Adjustment)” (Page 3-10).
5-13
SECTION 6
CIRCUIT DESCRIPTIONS
6-1. BK Board Descriptions
1-1. BK Select Switch
When the BK SELECT signal is “Low”, the Y/G signal input to the Y/G terminal (TB1) is input to IC101 (1/3) via the
buffer amplifier (Q100 and Q102). When “High”, the Y/G
signal input to the 11B terminal of CN2 is input to IC101
(1/3).
At IC101 (1/3), the 2Y/2G signal input to the 12B terminal
of CN2 is switched.
The same is performed for the PB/B signal and PR/R signal.
1-2. Clamp Circuit (1)
The analog switch (IC101) turns on according to the Y–CLP–
P pulse. As a result, the pedestal voltage of the Y/G signal is
sample-held. At IC102 (1/2), this voltage and the reference
voltage (Y CLAMP OFFSET voltage) are compared, the bias
current of the Y/G signal clamp amplifier (Q103 to Q105) is
controlled so that the pedestal voltage of the Y/G signal becomes reference voltage.
The same is performed for the PB/B signal and PR/R signal.
However, the PR signal (R–Y signal) and PB signal (B–Y
signal) are clamped by the C–CLP–P pulse.
1-3. W B INSERT Pulse Insertion Circuit
To adjust the level of the R–Y signal and B–Y signal, the
WHITE pulse and BLACK pulse are alternately inserted in
the horizontal blanking period of the signals.
For the Y/G signal, at IC101 (3/3), the voltage in the period
where the WHITE and BLACK pulses are inserted is made 0
Vdc. For the R–Y signal, the WHITE and BLACK pulses
are inserted at IC301 (3/3). The level of the WHITE pulse is
set by the R–Y PULSE LEVEL voltage. The level of the
BLACK pulse is set by the R–Y CLAMP OFFSET voltage.
These two voltages are switched by the WHITE INSERT P
at IC500 (2/3), passed through IC300 (1/2), and input to IC301
(3/3).
The same is performed for the B–Y signal.
1-4. Chroma Level Adjustment Circuit
The R–Y signal is level-adjusted by IC303 (gain control
amplifier). The R–Y signal output from IC303 is input to
IC304 (1/3) and the voltage of the WHITE pulse is sampleheld. At IC302 (2/2), this voltage and the CHROMA voltage
are compared, and the gain of IC303 is controlled. As a result, the WHITE pulse voltage becomes equal to the
CHROMA voltage. Consequently, by varying the CHROMA
voltage, the chroma level can be adjusted. The R–Y signal
output from IC303 is also input to IC325. Here, the voltage
of the BLACK pulse is sample-held. At IC320 (2/2), this
voltage and the GND level is compared to control the DC
bias of IC303. As a result, the pedestal level of the R–Y signal is fixed at the GND level.
The same is performed for the B–Y signal.
1-5. Matrix Circuit
The R, G, and B signals are created by inputting the Y, R–Y,
and B–Y signals to the matrix circuit.
• R Signal Matrix Circuit
At Q140, the Y signal and R–Y signal are added to create the
R signal.
• G Signal Matrix Circuit
At Q306, the R–Y signal which had passed through IC305
(gain control amplifier) is added with the B–Y signal. This
signal is inverted, amplified, and added to the Y signal at
Q350 to create the G signal. The mixing rate is determined
by R332, R333, and R340. The R–Y, and B–Y GAIN is finely
adjusted.
• B Signal Matrix Circuit
At Q540, the Y signal and B–Y signal are added to create the
B signal.
1-6. RGB Switch
The RGB signal and R, G, and B signals are switched after
the matrix circuit.
1-7. Clamp Circuit (2)
The voltage of the BLACK pulse of the R signal is sampleheld by IC107. At IC106 (1/2), this voltage and the GND
level are compared and the DC bias of the R signal amplifier
(Q142 to Q144) is controlled. As a result, the pedestal level
of the R signal is fixed at the GND level.
The same is performed for the G and B signals.
6-1
1-8. Half Blanking Switch
The character is half-blanked by the CHAR BLK signal.
1-9.
100 IRE Pulse, SET UP Pulse Insertion
Circuit
To adjust the contrast, the 100 IRE pulse and SET UP pulse
are alternately inserted in the horizontal blanking period of
the R, G, and B signals.
For the R signal, at IC110 (2/3), the 100 IRE pulse and SET
UP pulse are inserted. The level of the 100 IRE pulse is set
by the R 100 IRE voltage. The level of the SET UP pulse is
set by the R SET UP voltage. These two voltages are switched
by WHITE INSERT P by IC113 (1/3), and input to IC110
(2/3).
The same is performed for the G and B signals.
1-10. Blue-Only Switch
In the blue-only mode, the B signal is output instead of the R
signal at IC110 (3/3), and the B signal is output instead of
the G signal at IC310 (3/3).
1-11. Contrast, Bright Adjustment Circuit
The R signal is contrast-adjusted by IC112 (gain control amplifier). The R signal output from IC112 and amplified by
Q167 to Q169, input to IC113 (3/3), and the voltage of the
100 IRE pulse is sample-held. At IC114 (1/2), this voltage
and the CONT voltage are compared, and the IC112 gain is
controlled. As a result, the 100 IRE pulse and CONT voltage
becomes equal. Consequently, by varying the CONT voltage, the contrast level can be adjusted. The R signal output
from Q167 to Q169 is also input to IC113 (2/3). Here, the
voltage of the SET UP pulse is sample-held. At IC114 (2/2),
this voltage and the GND level is compared to control the
DC bias of IC112. As a result, the pedestal level of the R
signal is fixed at the GND level.
The DC bias of the R signal amplifier (Q167 to Q169) is
controlled by the BRT voltage to adjust BRIGHT.
At IC701 (1/3), the BRT voltage is created by switching the
BRIGHT voltage and BRT CENTER voltage in the period
inserted with the pulse (100 IRE pulse, and SET UP pulse)
and in other periods.
The same is performed for the B and G signals.
1-12. Pulse Insertion Circuit
At IC116, the BIAS REF pulse, DRIVE REF pulse, and character pulse are inserted in the R signal. The level of the BIAS
REF pulse is set by the BIAS REF voltage. The level of the
DRIVE REF pulse is set by the DRIVE REF voltage.
The same is performed for the B and G signals.
6-2
1-13. Drive Control Amplifier
To prevent the drive current of the CRT cathode from exceeding the reference value, and the drive voltage from exceeding the reference value, the levels of the R, G, and B
signals are controlled.
The drive current of the CRT cathode is detected by the current of pin 5 of the VIDEO OUT amplifier (IC119). The
current of pin 5 is clamped, I/V-converted by IC123, sampled by IC126 (2/3), and compared with the reference voltage (R DRIVE IK) at IC127 (2/2). When the drive current
exceeds the reference value, the signal output from IC127
(2/2) is passed through IC117 (3/3), Q170 to Q172, and input to IC115 (R drive control amplifier) to lower its gain.
The drive voltage of the CRT cathode is detected by the voltage of pin 9 of the VIDEO OUT amplifier (IC119). The
voltage of pin 9 is clamped by IC121, sampled by IC126
(1/3), and compared with the reference voltage (R DRIVE
V) at IC127 (1/2). When the drive voltage exceeds the reference value, the signal output from IC127 (1/2) is passed
through IC117 (2/3) and Q170 to Q172 and input to IC115
(R drive control amplifier) to lower its gain.
The SUB CPU (IC902) sets whether to control the drive
amount based on the drive current (current mode) or control
the drive amount according to the drive voltage (voltage
mode) (IK/V SW). Normally, the SUB CPU operates in the
voltage mode and sets into the current mode during WB adjustment. The DRIVE COMP is used for converting the data
of DRIVE V in the voltage mode, and the data of DRIVE IK
in the current mode.
1-14. Clamp Circuit (3)
The voltage of the BLACK pulse of the R signal is sampleheld by IC117 (2/3). At IC118 (1/2), this voltage and the
GND level are compared and the DC bias of the R signal
amplifier (Q174 to Q176) is controlled. As a result, the pedestal level of the R signal is fixed at the GND level.
The same is performed for the G and B signals.
1-15. Cut-Off Switch
At IC117 (3/3), the VIDEO TIMING pulse is used to switch
between the R signal and cut-off voltage (–0.3 Vdc.)
The same is performed for the G and B signals.
1-16. VIDEO OUT Amplifier
IC119 is used to drive the R signal cathode of the CRT.
The same is performed for the G and B signals.
1-17. G2 Control
Of the G2 R signal, G2 G signal, and G2 B signal, the signal
with the lowest voltage is input to IC705 (1/2), compared
with the reference voltage (G2 REF) to become the G2 CONTROL signal, and output from pin 10B of CN1 to the E
board through the C board to control the G2 voltage of the
CRT.
2. ABL, Overload Detection
At IC901 (1/2), the ABL voltage and reference voltage (–1
Vdc) are compared. Normally, the ABL voltage is above –1
Vdc and therefore the output level of IC901 (1/2) is “High”.
If the ABL voltage goes down and it becomes less than –1
Vdc, the CONT. BRT will be therefore controlled so that this
voltage will become –1 Vdc (constant). The output leve of
IC901 (1/2) is set to lower than the CONTRAST voltage and
therefore the OVERLOAD signal and therefore the OVERLOAD signal output from IC904 (1/2) becomes “High”.
3. Control Circuit
The SUB CPU (IC902) performs serial communication with
system controller using the three signals MISO, MOSI, and
SCLK, and outputs the control signal according to the instructions of the system controller.
This IC also reads the adjustment data of the EEPROM
(IC905) and outputs the adjustment voltage from the D/A
converter (IC906 to IC911).
6-2. BC Board Descriptions
Carries out the switching of the switches on each board and
setting of DAC data.
1. Serial Communication with Boards
The system control CPU (IC1) carries out serial communication with the SUB CPU of each board inserted in slots using the 4 signals-MISO, MOSI, SCLK and SLOT NO. It regularly receives abnormal detection signals from the power
supply circuit and deflection circuit, and information
(KILLER) for discriminating between color and black/white
for signals input from each input adapter. It chooses who to
communicate with using the signals SLOT-0 to SLOT-7.
2. Internal Signal Generation
IC104 to IC110 generates internal signals (PLUGE, 5STEP,
WHITE, GRAY, CROSS HATCH). The clock generated by
IC121 (525 mode:14.3181 MHz, 625 mode:14.1875 MHz)
is input to IC120 (sync generator) to generate the sync signal.
3. Character Generator
IC7 (character generator) is controlled to display the menu,
etc.
4. Parallel Remote Control
The input signal of CN5 (parallel remote control terminal) is
read by IC5 (I/O PORT EXPANDER).
5. ISR Terminal
The CPU (IC1) carries out communication with the ISR devices via IC23 (serial control unit) and IC27 and IC28
(RS232C transceiver).
6. Serial Remote Terminal
The CPU (IC1) carries out communication with the remote
devices via IC22 (serial control unit) and IC25 and IC26
(RS485 transceiver).
7. Communication with Control Block
(HC Board)
The CPU (IC1) carries out communication with the control
block (HC board) via IC14 (RS422 transceiver), receives key
input information and the memory card reading data, and
transmits LED light information and the memory card writing data.
6-3
6-3. E Board Descriptions
1. Horizontal System
1-1. H DELAY Circuit
IC621 is composed of the circuit generating the sawtooth
signal which uses the H SYNC of the input signal as the
trigger and the integral circuit. It outputs the signal obtained
by adding the sawtooth signal and parabola signal which synchronize with the input signals. IC622 compares this signal
with the reference voltage and outputs the rectangular wave.
The falling edge is deviated by about 1/4 of the horizontal
period from the input signal. Therefore in the H DELAY
mode, the signals are synchronized after a delay of about 1/4
horizontal period.
1-2. AFC Circuit
IC001 is a CRT driver and performs RGB signal processing,
sync and deflection signal processing.
This unit does not use a RGB signal processing circuit.
The AFC circuit of IC001 compares the phases of the H
SYNC of the input signal input to pin 6 and the pulse of the
horizontal deflection output input to pin $¡. The error signal
is passed through the low pass filter connected to pins $™,
$∞, $§, and $¶ to control the frequency and phase of the
ceramic oscillator connected to pin 44. The functions of IC001
consist of horizontal picture phase adjustment (H PHASE),
horizontal picture size adjustment (H SIZE), horizontal pin
distortion correction (H PIN), trapezoid distortion correction
(H KEY), horizontal bow distortion correction (H BOW),
and parallelogram distortion correction
(KEY BAL).
1-3. Horizontal Deflection Circuit
The H.DRIVE pulse is passed through Q053, T051 (HDT),
supplied to Q054 (H.OUT) to switch Q504 and drive T5002
(HOT) and H.DY.
The power supply of the horizontal output circuit is generated by IC071 (RWM control) by switching Q061 to improve
the power efficiency. The H PIN/W voltage from IC001 is
input to IC701 to control the power voltage.
1-4. H Center Circuit
Positive and negative power supplies from the secondary side
output of T052 (HOT:Horizontal output transformer) are generated as the power supply of the H center circuit. In the H
center circuit (IC091, IC101, Q091, D103), the DC current
flowing through the H.DY is controlled by the H.CENT signal from IC001.
6-4
1-5. Landing Circuit
The LANDING voltage output from the D/A converter of
IC201 inside is input to IC231 to control the current flowing
through the LANDING coil.
1-6. NTC Drive Circuit
The NTC signal output from IC201 is amplified by the IC801
to drive the NTC.
1-7. H Linearity Circuit
The H.LIN signal output from IC151 is amplified by Q151
to Q159, T151 (HLT) is driven, and the H linearity compensation current is passed through the H.DY.
1-8. Rotation Circuit (20-Inch Model)
The ROTATION voltage output from IC703 of the D/A converter is input to IC401 to control the current flowing through
the ROTATION coil.
1-9. H Convergence Circuit (20-Inch Model)
The H.CONV correct signal output from IC701 is amplified
by Q721 to Q729 to drive the CY (H).
The H.CONT correct signal output from IC701 is amplified
by IC702 to drive the CY (V).
2. Vertical System
2-1. V DELAY Circuit
IC641 is composed of the circuit generating the sawtooth
signal which uses the V SYNC of the input signal as the trigger and the amplifier circuit. It outputs the signal synchronized with the sawtooth signal. IC622 compares this signal
with the reference voltage and outputs the rectangular wave.
The falling edge is deviated by about 1/2 of the vertical period from the input signal. Therefore in the V DELAY mode,
the signals are synchronized after a delay of about 1/2 vertical period.
2-2. V. OSC Circuit
The V OSC circuit of IC001 adopts the countdown method.
It counts the horizontal pulses and resets using the V SYNC
input to pin 5. Its functions consist of the vertical picture size
adjustment (V SIZE), vertical picture position adjustment (V
POSITION), vertical linearity correction (V LIN), and vertical linearity balance correction (V LIN BAL).
2-3. Vertical Deflection Circuit
The V SAW signal output from IC001 is input to IC301 via
the buffer IC (IC091), and to drive the V.DY by IC301.
3. Protection Circuits
3-1. H.STOP, V.STOP Detection Circuit
The current flowing to the horizontal deflection york is converted to the parabola voltage of the horizontal period by
C065. This parabola voltage is used to switch Q121. The
C122 voltage charged by R122 is discharged in the horizontal period by Q121 so that it does not reach the voltage for
turning on Q122. When an error occurs in the horizontal deflection circuit, the voltage of C122 is used to turn on Q122
since Q121 does not turn on. Q122 turns off IC503 and stops
the high voltage generation circuit by setting pin 8 of IC503
to “Low”.
The current flowing to the vertical deflection york is converted to the sawtooth voltage of the vertical period by R035.
This sawtooth voltage is used to switch Q132, Hereafter the
operations are the same as the horizontal block.
4. Correction Signal Generation Circuit
4-1. Convergence Correction Signal Generation
Circuit
IC201 generates the convergence correction signal. It outputs the vertical convergence correction signal, horizontal
convergence correction signal of the vertical period, H STAT
adjustment voltage, landing adjustment voltage, and parabola
signal of the vertical period.
IC202 and IC204 consist of the circuit generating the sawtooth
signal of the horizontal period and the integral circuit. They
output the sawtooth signal of the horizontal period, parabola
signal, and sine signal.
IC701 is an integrated circuit consisting of a multiplier, signal switching circuit, and OP AMP amplifier. IC703 is DA
converter which outputs the d.c. voltage. IC701 modulates
the parabola signal of the horizontal period using the parabola
signal of the vertical period, varies the level using the DAC
output of IC703, and outputs the horizontal convergence correction signal of the horizontal period.
IC703 outputs the rotation adjustment voltage.
4-2. Horizontal Linearity Correction Signal,
Dynamic Focus Signal Generation Circuit
IC151 and IC301 an integrated circuit consisting of a multiplier, signal switching circuit, and OP AMP amplifier. IC205
is a D/A converter which outputs d.c. voltage. IC301 varies
the level of the parabola signal of the vertical period using
the DAC output of IC205 and outputs the dynamic focus signal of the vertical period. It also modulates the parabola signal of the horizontal period using the parabola signal of the
vertical period whose level has been varied using the DAC
output of IC205 and the signal obtained by adding level using the DAC output of IC205, and outputs the dynamic focus
signal of the horizontal period.
IC151 and IC301 adds the parabola signal of the horizontal
period whose level was varied using the DAC output of IC205,
the sine signal of the horizontal period whose level was varied using the DAC output of IC205, and the signal modulated by the parabola signal of the vertical period in which
the level of the two signals was varied using the DAC output
of IC205, and outputs the horizontal linearity
signal.
5. Control Circuit
The SUB CPU (IC7001) performs serial communication with
the system control CPU of the BC board using the three signals MISO, MOSI, and SCLK, and outputs the control signals POWER ON, DEGAUSE, AFC SW, H.DELAY,
V.DELAY, etc. according to the instructions of the system
control CPU (BC board IC1). It also reads the adjustment
data of the EEPROM (IC7004) and output the adjustment
voltage from the D/A converter (IC7005). In addition, it also
controls the waveform output from IC112, IC115, and IC118
of the D board. The following protect detection signals are
transmitted to the system control CPU from the SUB CPU.
H.STOP, V.STOP, +B.PROT, HV_OVP
IK_PROT, HV_OVP, G.PROT1 to 4
6-5
6. High Voltage Block
6-1. High Voltage Regulator Circuit
The high voltage regulator of this unit uses a DC converter
type power supply circuit to reduce the power consumption.
The following is an outline of the operations of the high voltage regulator.
The detection voltage which is obtained by resistance-dividing the HV voltage with the high voltage detection resistance HVR inside the FBT is passed through the IC501 (1/2)
buffer and input to IC503. IC503 compares the reference
voltage of IC502 and this detection voltage (difference amplification) and performs PWM modulation. Q551 is PWMmodulated and driven by the output of IC503. The voltage
supplied to the FBT drive circuit (Q109, C108, C104, and
FBT) is controlled by the ON/OFF of Q551.
Next, the current is supplied to the CRT, and if the HV voltage drops, the HV detection voltage also drops. As a result,
the PWM output of IC503 works to expand the ON period of
the Q551 switching FET.
The voltage switched by Q551 is passed through the combination choke L552 (LOT) and supplied to the converter circuit for driving FBT. As the PWM modulator is synchronized by the HV DRV pulse, the size of the drain current of
the FET from Q555 of the FBT drive circuit depends on the
ON period of Q551. Consequently, when the ON period of
Q551 increases, the Q555 drain current increases and the
C559 potential increases.
When Q555 turns OFF, the flyback pulse generated by the
combined inductance of the LOT and FBT and the resonance
of C108 and transmitted to the secondary side of the FBT to
generate the HV voltage.
6-2. High Voltage Protector Circuit
HV is detected using the voltage of the HV.PROT winding,
the tertiary winding of FBT.
The HV.PROT is connected to the ‘ input terminal of IC531
(2/2) via D901 and R902 of the P board and the rectification
circuit composed of C541.
When HV increases due to some error, fault, etc., the
HV.PROT voltage drops. When the voltage of the ‘ input
terminal decreases below the ’ input terminal voltage, the
protector operation reference voltage, the comparator output
becomes “Low”, and turns OFF IC503via D545.
Consequently, the drive pulse of the high voltage converter
is shut down and the high voltage output circuit stopped.
6-6
6-3. High Voltage Current Protector, ABL Circuit
The high voltage current protector holds down the high voltage regulator when the current Ik flowing through the CRT
exceeds the setting value in errors and malfunctions.
The voltage obtained by resistance-dividing at R531 and R532
the difference between REF (IC502) and the VABL1 obtained
by voltage-converting the current flowing through the FBT
secondary winding of the P board at R906 is supplied to the
‘ terminal of the comparator, and the protector operating
point voltage is supplied to the ’ pin of the comparator after
resistance-separating VREF by R533 and R534.
The ‘ terminal voltage of the comparator is normally higher
than the ’ terminal voltage. When the CRT beam current
increases, the VABL1 voltage decreases and consequently the
‘ terminal voltage of the comparator also decreases. Therefore when the beam current, which makes the ‘ terminal
voltage drop below the ’ terminal voltage, flows through
the CRT, the protector operates and shuts down the PWM
control IC DRIVE, and holds down the high voltage regulator.
The ABL circuit serves to protect the CRT by preventing the
beam current from exceeding the reference value.
The beam current flowing through the CRT flows to R903 of
the P board. VABL2 is obtained by converting this current to
voltage. VABL2 is supplied to the ‘ terminal of IC901, and
when it drops below the reference voltage of the ’ terminal,
ABL operates and makes the luminance consistent.
6-4. DF Drive Circuit
The DFX and DFY signal from the IC301 is amplified by
Q301 to Q305 and T301 (DFX), and DFY is amplified by
Q321 and Q322 to modulated the G4 and GM voltage of the
CRT via the focus pack integrated with the FBT of the P
board.
6-4. C Board Descriptions
6-5. Power Supply Circuit Descriptions
(G Board)
1. Screen (G2) voltage regulator
The G2 regulator circuit composed of IC601 (1/2), Q601 and
Q602 is controlled by the G2 control voltage from the BK
board and supplies the G2 voltage which optimizes the CRT
cathode voltage. This board uses a high voltage obtained by
rectifying the drain pulse voltage of Q555 of the E board at
D555 and C558.
The power supply of this unit is composed of the following
three switching regulators.
1. Power-factor correction regulator for conforming to the
power supply harmonic regulation
2. LOW-B regulator for supplying the voltage required by
the processing circuits of the signal block and deflection/high voltage blocks mainly
3. HIGH-B regulator for supplying voltage required by the
output circuits of the deflection/high voltage blocks
2. Blanking Circuit
The blanking signal from the BK board is amplified by IC701,
clamped to –12V by D501, and supplied to G1 of the CRT.
1. Power-factor correction block
The power-factor correction circuit (hereafter referred to as
PFC) is composed of T3, IC31, Q31, D36, C43, and related
parts.
The power-factor correction circuit of this power supply
adopts the boost PWM control method. In the basic operations, the output voltage Vpfc is made higher than the peak
value of the input power supply voltage at all times by the
boost type switching regulator which performs continuous
current operations. Unlike the normal regulator, as the input
voltage is a sine wave, voltage control and current control
proportionate to this are performed. Consequently, IC31
which PWM controls PFC not only makes the Vpfc voltage
constant but also PWM controls Q31 which is the FET for
PFC OUT so that the current flowing to T3 (input power
supply current waveform) becomes the same as the input
power supply voltage waveform.
As the waveforms of the input voltage and current become
similar, the power-factor is improved.
2. LOW-B Regulator
The power supply for LOW-B is mainly composed of IC201,
IC203, PH201, Q205, T201, and T201 secondary rectification circuits.
IC201 which is a PWM control IC is added with the control
voltage from IC203 which performs constant voltage control of the +15V line via the isolater PH201. The Q205 FET
which is the output from the converter is switched by the
pulse PWM controlled by IC201 via the Q203 and Q204
buffers. As a result, at the secondary side of T201, +7V for
the standby +5V and +6V/–6V/+15V/–15V which are required by each board are generated.
The standby +5V voltage is generated by IC202 which is an
error amplifier and Q207 which is a pass transistor. The power
supply voltage lines supplied to each board are incorporated
with transistor switches to reduce power consumption during standby.
6-7
3. HIGH-B Regulator
The HIGH-B power supply is composed of IC301, IC302,
PH301, PH801, Q305, T301, and T301 secondary rectification circuits.
Like the LOW-B power supply, IC301 which is a PWM control IC is added with the control voltage by IC302 performing constant voltage control of the +120V line via the isolater
PH301. Q305 FET which is a converter out is switched by
the PWM controlled pulse by IC301 via the Q303 and Q304
buffers. As a result, +120V used for the voltage for the CRT
heater and voltage used by the deflection/high voltage output blocks are generated.
4. Protection Circuits
4-1. PFC Over-voltage Protection (OVP) Circuit
This circuit is composed of IC101 (1/2), Q105, Q106, and
the Vpfc voltage detector (R53 to R57). When the Vpfc voltage rises abnormally due to malfunctions of the feedback
block for Vpfc voltage control, it stops PFC operations. IC101
(1/2) which is the detector observes the voltage obtained by
resistance-dividing the Vpfc voltage at a certain percentage.
When the Vpfc voltage rises in malfunctions, exceeds the
reference voltage set, it sets the output to HI. As a result, the
latch output composed of Q105 and Q106 is passed through
D102 to set the ENABLE terminal of IC31 to “Low” and
stops the PFC operations.
At the same time, D103 (red LED) is lit to inform of the
error.
4-2. LOW-B Power Supply Protection Circuit
The protection circuit of this power supply is composed of
the power supply circuit for IC201 composed of Q4, Q5, Q6,
IC1, PH901, Q802, Q817, etc. and the following detection
circuit.
The detection circuit detects the over-voltage of the standby
+5V and +15V lines. The OVP circuit of the standby +5V is
composed of the reference voltage IC802, detector IC801
(2/4) and switch Q801 while the +15V line OVP circuit is
composed of the detector IC804. The protection circuit operates when the power supply voltage to IC201 PWM controlled is stopped.
Specifically, when the +15V voltage rises due to an error of
the voltage feedback block, and the value determined by the
percentages of R825 and R826 is exceeded, the output of
IC804 becomes “Low”, and Q816 is turned OFF via D810,
to turn OFF the transistor in PH803. As a result, Q4 and Q5
turn ON, Q6 goes OFF so that no power supply voltage is
supplied to IC201 and PWM operations stop.
When the OVP circuit of the standby +5V works, Q802 is
turned OFF and the same operations are performed. At the
same time, D4 (red LED) is lit to in form of the error.
6-8
4-3. HIGH-B Power Supply Protection Circuit
The protection circuit of this power supply is composed of
the PWM control pulse shut-off circuit composed of Q300,
Q301, PH802, Q814, Q815, etc. and the following detection
block.
The detection circuit is composed of the +120V OVP and
OCP (over-current). The OVP circuit is composed of the detection block IC801 (3/4), and latch block Q806 and Q807,
while the OCP circuit is composed of the detector IC801 (4/
4), latch block Q809 and Q810. The reference voltage used
is shared with IC802.
Taking the OCP circuit as an example to describe the circuit
operations, when the +120V current increases due to load
problems, etc., the voltage of the R339 current-voltage conversion resistor also drops significantly, and the voltage value
observed by IC801 (4/4) also drops.
When the voltage value drops below the value obtained by
resistance-dividing by R819 and R820, the detector IC801
(4/4) output becomes “High”, turns ON the Q809 and Q810
latch via D810, and turns ON Q815 to turn OFF the transistor in PH802. As a result, Q301 is turned ON by the current
from R290, Q300 turns ON, and the Vref voltage (5V) (voltage of pin !¢) is input to pin 4 of the PWM control IC301
via D300. pin 4 of IC301 performs duty limitation of the
output pulse. When voltages above 3V are supplied, the output pulse is shut-off.
Therefore, the power supply is stopped by shutting-off the
PWM output pulse.
When the OVP circuit operates, the output of IC801 (3/4)
becomes “High” and the same operations are performed
again.
6-6. Control Unit Descriptions
(BVM-14G5, BKM-10R)
• HC Board
1. Key Scan, LED Lighting
The SUB CPU (IC1) transmits the LED lighting signal and
key scanning output signal to the HA board and HB board
using the serial signals (MISO, MOSI, SCLK), and receives
the key scanning input signals.
2. Memory Card
The SUB CPU (IC1) reads/writes the data (adjustment data,
etc.) from/on the memory card connected to CN1.
6-9
SECTION 7
SEMICONDUCTORS
CAT28F020P-L5
CXA2026AS
CXD2343S
CXK58257CM-70LL-T6
HN27C256AG-10
µPD71051GU-10E2
HD6435368AG14M
LM2990T-5.0
NJM7912FA
CPX2003M
NJU3716M-T2
HD6473258P10
CXD1030M-T6
HD6475368CP-10-EG2.0
CXA1211M-T4
CXA1521M-T4
LM393S-E20
LM393PS-E20
LM358PS-E20
LTC485CS8-E2
LTC490CS8-E2
MAX877CSA
MM1026BFB
NJM4558M-TE2
TC4W53FU(TE12R)
TC7W32FU(TE12R)
TC7W74FU(TE12R)
TL082CPS-E05
TL082CPS-E20
X25040S-C7000
CXD1095Q
LA6500-FA
LM339NS-E20
MB89613R-236
MB89613R-438
MC74HC00AFEL
MC74HC02AFEL
MC74HC11FEL
MC74HC14AFEL
MC74HC30FEL
MC74HC125AFEL
NJM1496M-TE2
SN74HC05ANS-E05
TC74HC03AF(EL)
TC74VHC00F(EL)
TC74VHC02F(EL)
TC74VHC04F(EL)
TC74VHC10F(EL)
TC74VHC14F(EL)
TC74VHC74F(EL)
TC74VHC125F(EL)
TC74VHC138F(EL)
TC74VHCU04F(EL)
TLC2932IPW-E20
PQ12TZ5U
PST529CMT-T1
STV9379
CXD1171M-T6
LA6510
CXA1726AM-T6
CXA1840S
FA5301BN-TEL
MAX202CSE-T
MC74HC147FEL
MC74HC175FEL
MC74HC4051FEL
MC74HC4053FEL
MC74HC4538AFEL
TC74VHC123AF(EL)
TC74VHC138F(EL)
TC74HC151AF(EL)
TC74VHC163F(EL)
TC74HC166AF(EL)
TC74VHC175F(EL)
TC74VHC4040F(EL)
TL494CNS-E20
MB88346BPFV-EF
TC74VHC244F(EL)
TC74VHC245F(EL)
TC74VHC541F(EL)
TC74VHC574F(EL)
µPD6453GT-101-E1
TC7S00FU(TE85R)
TC7S02FU(TE85R)
TC7S32FU(TE85R)
TC7S86F(TE85R)
TC7W078FU(TE12R)
LM2940CT-5.0
NJM7809FA
NJM7812FA
NJM7815FA
NJM79L05A-T3
TDA6101Q/N3
7-1
TK83854D
TL431CLP-Z
IRFI9630GS-LF
IRFI9680GS
2SA1469-R
2SA1606-E
2SB1261-K
2SB1565EF
2SC3746
2SC4159-E
2SC4686A(LBSONY)
2SD2394-EF
2SC4927-01
D5LC20U
D5SC4M
HSM83-TL
RD6.8M-T1B1
RD7.5M-T1B2
RD22M-T1B3
2SD1834-T101
D5L60
Z8622812PSC
MA111-TX
RD3.0SB-T1
RD4.3SB3-T1
RD5.6SB-T1
RD6.2SB-T1
RD12SB-T1
RD12SB2-T1
RD12SB3-T1
RD15SB-T1
S2C2785TP-HFE
2SA1413-K
2SK520K44K45-T1B
DTA124EKA-T146
DTC144EK-T146
DTC144EKA-T146
2SA1037K-T-146-QR
2SA133B-5-TB
2SA1462-T1Y33Y34
2SC1654-T1N5
2SC2412K-T-146-QR
2SC3326N-TE85L-AB
2SC3392-5-TB
2SC3545-T1T43T44
2SC3837KT146Q
2SK2209-01R-F165
2SK2655-01R-F165
2SK2766-01R-F165
EGP10DPKG23
ERB91-02TP1
ERC91-02TP11
RGP15K-6179G23
SLR-325DCT31
SLR-325MCT31
2SA120BS-TP
2SC2362KG-AA
CL-155Y/PG-CD-TL
EGP10GPKG23
RD18ES-T1B3
RD20ES-T1B1
RD24ES-T1B1
1SS119-25TD
SLR-325VCT31
2SA1221-T-KLM
2SC2958-TL
IMT2-T109
D1NS4-TR2
GP08DPKG23
RD24SB-T1
RGP02-20EL-6394
2SC2688-L
2SC3840K
V19E-T52
IMX2-T109
D4SB60L
7-2
SECTION 8
EXPLODED VIEWS
NOTE :
• Items with no part number and no description are not stocked because they are seldom required for routine service.
• The construction parts of an assembled part are indicated with a
collation number in the remarks column.
• Items marked “ * “ are not stocked since they are seldom required
for routine service. Some delay should be anticipated when ordering these items.
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
8-1
BEZEL, CABINET
8-1. BEZEL, CABINET (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U)
: 7-685-648-79
: 7-682-947-01
: 7-682-561-09
: 7-628-000-04
: 7-682-161-01
: 7-682-547-09
: 7-685-647-79
: 7-682-963-09
+BVTP3x12
+PSW3x6
+B4x8
+PS5x14
+P4x8
+P3x6
+BVTP3x10
+PSW4x14
1
3
3
4
2
12
15
11
9
13
14
8
10
20
10
16
19
17
3
7
9
18
8
23
5
22
24
14G1A/14G1E/14G1U
6
21
33
34
31
29
32
27
26
26
25
28
27
14G5A/14G5E/14G5U
8-2
30
BEZEL, CABINET
REF NO.
PART NO.
DESCRIPTION
1
1
2
3
4
4-050-931-01
4-050-967-01
* 4-053-287-11
4-063-969-01
4-050-933-01
CABINET (UPPER)(14G5)
CABINET (UPPER)(14G1)
GASKET
SCREW (OS), CASE, CLAW
CABINET (LEFT)
5
6
7
8
9
4-050-932-01
* 4-053-255-01
* 4-053-254-01
X-3642-018-3
* 3-642-047-01
CABINET (RIGHT)
GASKET (S), EMI
GASKET (L), EMI
HANDLE ASSY
STOP, HANDLE
10
11
11
12
13
*
*
*
*
*
4-050-928-01
X-4035-465-1
X-4035-466-2
X-4033-104-1
4-050-804-01
BRACKET, HANDLE
PANEL ASSY, REAR (14G1)
PANEL ASSY, REAR (14G5)
PANEL ASSY, BLANK
SCREW, PANEL STOPPER
14
15
16
17
18
*
*
*
*
*
3-648-057-00
4-050-913-01
A-1373-641-A
4-050-876-01
A-1373-638-A
NUT (ISO-4), U
INSULATOR (ANODE)
YA MOUNT
PLATE, LIGHT INTERCEPTION
YB MOUNTED (14G1)
18
19
19
20
21
*
*
*
*
A-1373-661-A
A-1373-636-A
A-1373-643-A
4-061-920-01
X-4033-128-1
YB MOUNT (14G5)
YC MOUNTED (14G1)
YC MOUNT (14G5)
INSULATOR, YC
MASK (4:3) ASSY
22
23
24
25
26
* X-4033-276-1
* X-4033-277-1
X-4033-145-1
X-4033-130-1
4-050-922-01
GUARD ASSY, HARNESS(L)(14G1)
GUARD ASSY, HARNESS(S)(14G1)
BEZEL ASSY (14G1)
BEZEL ASSY (14G5)
BASE, HANDLE (14G5)
27
28
29
30
31
* 4-337-212-11
4-050-851-01
* A-1372-133-A
* 4-050-925-01
* A-1372-134-A
HANDLE (14G5)
KNOB, CONTROL (14G5)
MOUNTED PWB, HA (14G5)
BRACKET (RIGHT), BEZEL (14G5)
MOUNTED PWB, HB (14G5)
32
33
34
* 4-050-924-01
* A-1375-155-A
1-500-249-11
BRACKET (LEFT), BEZEL (14G5)
HC COMPLETE PWB (14G5)
BEAD, FERRITE (CASE)(14G5)
REMARK
9
13,14
8-3
CARD SLOT
8-2. CARD SLOT (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U)
: 7-685-648-79
: 7-685-872-09
: 7-682-161-01
: 7-432-114-11
+BVTP3x12
+BVTT3x8
+P4x8
SCREW LOCK
72
61
73
59
74
60
75
62
58
63
52
51
57
65
14G1A/14G1E
71
54
64
56
70
14G1A/14G1E
14G5A/14G5E
66
55
53
67
68
69
14G1A/
14G1E/
14G1U
57
58
8-4
CARD SLOT
REF NO.
PART NO.
DESCRIPTION
A-1390-771-A
4-050-965-01
4-053-287-21
A-1390-772-A
4-050-964-01
TA MOUNT
BRACKET (L), T
GASKET
TB MOUNT
BRACKET (R), T
51
52
53
54
55
*
*
*
*
*
56
57
58
58
59
* 4-053-287-01
* 4-053-287-11
4-050-969-01
* 4-050-844-01
* A-1316-334-A
GASKET
GASKET
BOARD, CARD SLOT (14G1)
BOARD, CARD SLOT (14G5)
G COMPL
60
61
62
63
64
* X-4033-116-1
X-4033-109-6
* A-1346-666-A
* X-4033-108-1
* A-1135-941-A
FRAME ASSY, POWER
PANEL ASSY, POWER UNIT
E COMPL
HEAT SINK ASSY, DEF
BK COMPL
65
66
67
68
69
*
*
*
*
*
X-4033-105-1
A-1135-920-A
X-4033-106-2
4-050-816-01
A-1372-136-A
PANEL (BK) ASSY, CONNECTOR
BC COMPL
PANEL (BC) ASSY, CONNECTOR
BRACKET, HD (14G1)
MOUNTED PWB, HD (14G1)
70
1-500-278-11
71
72 !
73 !
74
1-500-249-11
1-251-263-11
1-762-300-11
2-990-241-02
FILTER, CLAMP (FERRITE CORE)
(14G1A/14G1E/14G5A/14G5E)
BEAD, FERRITE (CASE) (14G1A/14G1E)
INLET, AC
SWITCH, AC POWER SEESAW
HOLDER, PLUG A
75
4-050-798-01
PLATE, NUT, AC INLET
REMARK
60,61,72-75
63
65
67
8-5
PICTURE TUBE
8-3. PICTURE TUBE (14G1A/14G1E/14G1U/14G5A/14G5E/14G5U)
: 7-682-564-09
: 7-685-872-09
: 7-682-161-01
: 7-682-661-01
: 7-688-004-02
+P4x14
+BVTT3x8
+P4x8
+PS4x8
W4
124
125
114
126
116
127
115
104
113
118
109
102
101
117
105
110
111
112
108
106
107
103
119
122
120
8-6
123
121
PICTURE TUBE
REF NO.
PART NO.
DESCRIPTION
101
102
103 !
103 !
104
*
4-306-034-00
4-348-567-00
8-738-333-05
8-738-335-05
4-047-349-01
NUT,(B) (M5), FLANGE
WASHER, CRT POSITION
PICTURE TUBE 14MT1 (14G1A/14G1E/14G5A/14G5E)
PICTURE TUBE 14MT3 (14G1U/14G5U)
HOLDER, HV CABLE
105
106
107 !
108
109 !
4-050-492-01
4-053-410-01
8-451-473-11
X-2105-533-1
1-452-436-41
SPACER, DY
SHIELD, DY
DY Y14MPDT
PLATE ASSY, CORRECTION, TLH
NECK ASSY, CRT (NA292)
110
* A-1331-724-A
111
4-303-774-XX
112 !
1-411-660-21
113 !
1-411-658-21
114
4-063-324-01
C MOUNT
SPRING
COIL, DEMAGNETIC
COIL, LANDING CORRECTION
HOLDER, LCC
115
115
116
116
117
CHASSIS (L)(14G1)
CHASSIS (L)(14G5)
CHASSIS (R)(14G5)
CHASSIS (R)(14G1)
FBT BLOCK ASSY
4-063-789-01
* 4-063-787-01
4-050-926-01
4-050-962-01
* A-1482-705-A
118 !
X-4035-494-1
119
* X-4035-463-1
119
* X-4035-464-1
120
3-831-441-99
121
X-4033-117-1
FBT ASSY NX-4141//J1F4
CHASSIS ASSY, BOTTOM (14G5)
CHASSIS ASSY, BOTTOM (14G1)
CUSHION, SPEAKER
FOOT ASSY
122
123
124
125
126
X-4836-202-9
* 3-668-845-01
4-308-870-00
1-452-032-00
1-452-094-00
FOOT
CUSHION, LEG
CLIP, LEAD WIRE
MAGNET,DISC:10MM
MAGNET, ROTATABLE DISK:15MM
127
4-051-735-22
REMARK
118
120
122,123
PIECE A(75), CONV. CORRECT
8-7
BEZEL, CABINET
8-4. BEZEL, CABINET (20G1A/20G1E/20G1U)
: 7-682-566-04
: 7-685-661-14
: 7-685-647-79
: 7-685-872-09
: 7-682-561-09
+B4x20
+BVTP4x12
+BVTP3x10
+BVTT3x8
+B4x8
153
153
155
152
151
154
161
157
153
165
163
162
164
158
167
156
166
170
169
171
161
153
173
162
168
172
175
169
159
160
153
174
158
157
176
156
8-8
BEZEL, CABINET
REF NO.
PART NO.
DESCRIPTION
151
152
153
154
155
X-4033-308-1
4-050-837-01
4-063-969-01
X-4033-310-1
4-050-840-01
CABINET ASSY, TOP
CABINET, TOP
SCREW (OS), CASE, CLAW
CABINET ASSY, LEFT
CABINET, LEFT
156
157
158
159
160
* X-4033-324-2
4-050-836-01
* 3-342-839-02
X-4033-309-1
4-050-841-01
BLIND COVER ASSY
COVER, BLIND
CUSHION
CABINET ASSY, RIGHT
CABINET, RIGHT
161
162
163
164
165
X-3642-018-3
* 3-642-047-01
* X-4035-466-1
4-050-821-01
* X-4033-104-1
HANDLE ASSY
STOP, HANDLE
PANEL ASSY, REAR
ESCUTCHEON
PANEL ASSY, BLANK
166
167
168
169
170
* 4-050-804-01
3-648-057-00
1-500-278-11
* 4-050-830-01
* A-1373-641-A
SCREW, PANEL STOPPER
NUT (ISO-4), U
FILTER, CLAMP (FERRITE CORE)
BRACKET, BEZEL
YA MOUNT
171
172
173
174
175
* 4-050-876-01
* A-1373-642-A
* A-1373-643-A
X-4033-111-1
4-051-061-02
PLATE, LIGHT INTERCEPTION
YB MOUNT
YC MOUNT
BEZEL ASSY
HOLDER, MASK
176
X-4033-112-1
REMARK
152
155
157,158
160
162
166,167
175
MASK (4:3) ASSY
8-9
CARD SLOT
8-5. CARD SLOT (20G1A/20G1E/20G1U)
: 7-685-648-79
: 7-685-872-09
: 7-682-161-01
: 7-432-114-11
+BVTP3x12
+BVTT3x8
+P4x8
SCREW LOCK
220
210
221
208
222
209
223
211
207
212
202
201
206
214
203
213
205
215
204
217
216
218
219
20G1A/20G1E
206
207
8-10
CARD SLOT
REF NO.
PART NO.
DESCRIPTION
201
202
203
204
205
*
*
*
*
*
A-1390-771-A
4-050-965-01
A-1390-772-A
4-050-964-01
4-053-287-01
TA MOUNT
BRACKET (L), T
TB MOUNT
BRACKET (R), T
GASKET
206
207
208
209
210
*
*
*
*
4-053-287-11
4-050-844-01
A-1316-334-A
X-4033-116-1
X-4033-109-6
GASKET
BOARD, CARD SLOT
G COMPL
FRAME ASSY, POWER
PANEL ASSY, POWER UNIT
211
212
213
214
215
*
*
*
*
*
A-1346-667-A
X-4033-108-1
A-1135-921-A
X-4033-105-1
A-1135-920-A
E COMPL
HEAT SINK ASSY, DEF
BK COMPL
PANEL (BK) ASSY, CONNECTOR
BC COMPL
REMARK
209,210,220-223
212
214
216
216
* X-4033-106-2
217
* 4-050-816-01
218
* A-1372-136-A
219
1-543-653-11
220 !
1-251-263-11
PANEL (BC) ASSY, CONNECTOR
BRACKET, HD
MOUNTED PWB, HD
CORE ASSY, BEAD(DIVISION TYPE)(20G1A/20G1E)
INLET, AC
221 !
222
223
SWITCH, AC POWER, SEESAW
HOLDER, PLUG A
PLATE, NUT, AC INLET
1-762-300-11
2-990-241-02
4-050-798-01
8-11
PICTURE TUBE
8-6. PICTURE TUBE (20G1A/20G1E/20G1U)
: 7-685-872-09
: 7-682-161-01
: 7-682-661-01
: 7-682-261-09
: 7-682-665-09
: 7-685-881-09
+BVTT3x8
+P4x8
+PS4x8
+K4x8
+PS4x16
+BVTT4x8
268
266
275
265
276
267
277
262
254
269
261
278
259
270
255
252
257
251
264
263
258
260
262
253
256
272
273
274
8-12
271
PICTURE TUBE
REF NO.
PART NO.
DESCRIPTION
251
252
253 !
253 !
253 !
4-306-034-00
4-348-567-00
8-736-378-05
8-736-380-05
8-736-388-05
NUT,(B) (M5), FLANGE
WASHER, CRT POSITION
PICTURE TUBE 20MT1 (20G1E)
PICTURE TUBE 20MT3 (20G1U)
PICTURE TUBE 20MT1(S) (20G1A)
254
* 4-047-349-01
255
* 4-040-897-01
256
* X-4033-336-3
257 !
8-451-470-13
258 !
8-453-003-11
HOLDER, HV CABLE
SPACER, DY
SHIELD ASSY, DY
DY Y20MPD-M
NA3012(M)
259
* A-1331-724-A
260
4-303-774-XX
261
4-316-015-00
262
4-041-021-02
263 !
1-411-659-21
C MOUNT
SPRING
HOLDER, WIRE
HOLDER, DEGAUSE COIL
COIL, DEMAGNETIC:10MM
264 !
1-411-657-21
265
* 4-387-284-01
266
* X-4035-467-1
267
* X-4033-115-1
268
4-063-969-01
COIL, LANDING CORRECTION
HOLDER, LEAD
CHASSIS ASSY, LEFT
CHASSIS ASSY, RIGHT
SCREW (OS), CASE, CLAW
269
* A-1482-707-A
270 !
X-4035-493-1
271
* X-4033-113-1
272
X-4033-117-1
273
X-4836-202-9
FBT BLOCK ASSY
FBT ASSY NX-4141//J1E4
PLATE ASSY, BOTTOM
FOOT ASSY
FOOT
274
275
276
277
278
CUSHION, LEG
CLIP, LERD WIRE
MAGNET,DISC
MAGNET, ROTATABLE DISK:15MM
PIECE A(90), CONV. CORRECT
* 3-668-845-01
4-308-870-00
1-452-032-00
1-452-094-00
4-051-736-21
REMARK
270
273,274
8-13
CONTROL UNIT
8-7. CONTROL UNIT (BKM-10R)
+B4x8
+B4x8
407
408
+B4x8
+PSW3x6
+PSW3x6
+B4x8
406
405
402
409
411
412
410
403
+PSW3x6
+BV3x12
+BV3x12
+PS4x16
+BV3x12
404
401
REF NO.
PART NO.
DESCRIPTION
401
402
403
404
405
4-050-851-01
X-4033-118-1
* A-1372-134-A
* A-1372-133-A
* A-1375-149-A
KNOB, CONTROL
PANEL ASSY, CONTROL
HB MOUNTED PWB
HA MOUNTED PWB
HC COMPLETE PWB
406
* A-1372-136-A
HD MOUNTED PWB
8-14
REMARK
REF NO.
PART NO.
DESCRIPTION
407
408
409
410
4-050-852-01
4-050-858-01
4-050-857-01
X-4033-117-1
HOLDER, FOOT
COVER (TOP)
COVER (BOTTOM)
FOOT ASSY
411
412
X-4836-202-9
* 3-668-845-01
FOOT
CUSHION, LEG
REMARK
411,412
BC
SECTION 9
ELECTRICAL PARTS LIST
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
•
•
All variable and adjustable resistors have
characteristic curve B, unless otherwise
noted.
•
•
RESISTORS
All resistors are in ohms
F : nonflammable
•
CAPACITORS
PF : µµF
When indicating parts by reference
number, please include the board
name.
•
There are some cases the reference
number on one board overlaps on the other
board. Therefore, when ordering parts by
the reference number, please include the
board name.
Items marked " * " are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
REF NO.
PART NO.
DESCRIPTION
REMARK
* A-1135-920-A BC COMPL
****************
* X-4033-106-1
* 1-526-659-00
* 1-526-660-21
1-540-222-11
1-550-104-11
PANEL (BC) ASSY, CONNECTOR
SOCKET, IC (DP) 28P
SOCKET, IC (DP) 32P
SOCKET, IC (PCC PACKAGE) 84P
HOLDER, BATTERY
* 3-648-057-00
* 4-050-804-01
* 4-050-814-01
* 4-057-770-01
7-432-114-11
NUT (ISO-4), U
SCREW, PANEL STOPPER
SHIELD, PWB
INSULATOR
SCREW LOCK
7-623-422-07 LW 3, TYPE B
7-685-871-01 SCREW +BVTT 3X6 (S)
7-685-872-09 SCREW +BVTT 3X8 (S)
<CAPACITOR>
C1
C2
C3
C4
C5
1-163-235-11
1-163-227-11
1-163-235-11
1-163-235-11
1-126-396-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
22PF
10PF
22PF
22PF
47MF
5%
0.5PF
5%
5%
20%
C7
C8
C9
C10
C11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-275-11
1-163-275-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.001MF 5%
0.001MF 5%
50V
50V
50V
50V
50V
C12
C31
C32
C33
C34
1-163-031-11
1-163-038-11
1-163-038-11
1-163-038-11
1-163-038-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.1MF
0.1MF
0.1MF
0.1MF
50V
25V
25V
25V
25V
C35
C36
C37
C39
C41
1-163-038-11
1-163-038-11
1-163-038-11
1-163-038-11
1-163-038-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.1MF
0.1MF
0.1MF
0.1MF
25V
25V
25V
25V
25V
C42
C43
C44
C45
C46
1-163-038-11
1-163-038-11
1-163-038-11
1-163-038-11
1-163-099-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.1MF
0.1MF
0.1MF
18PF
25V
25V
25V
25V
50V
5%
50V
50V
50V
50V
16V
REF NO.
PART NO.
DESCRIPTION
REMARK
C47
C51
C104
C105
C106
1-163-231-11
1-163-133-00
1-164-489-11
1-163-231-11
1-163-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
15PF
470PF
0.22MF
15PF
10PF
5%
5%
10%
5%
0.5PF
C107
C108
C109
C110
C111
1-163-099-00
1-163-227-11
1-163-038-11
1-163-031-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
18PF
10PF
0.1MF
0.01MF
2.2MF
5%
50V
0.5PF 50V
25V
50V
16V
C112
C113
C114
C115
C116
1-164-505-11
1-163-031-11
1-163-031-11
1-163-235-11
1-163-235-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
0.01MF
0.01MF
22PF
22PF
5%
5%
16V
50V
50V
50V
50V
C117
C118
C151
C154
C155
1-163-031-11
1-163-017-00
1-126-396-11
1-164-004-11
1-164-182-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.0047MF
47MF
0.1MF
0.0033MF
10%
20%
10%
10%
50V
50V
16V
25V
50V
C156
C157
C201
C202
C203
1-164-344-11
1-164-004-11
1-126-392-11
1-126-392-11
1-126-392-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
0.068MF
0.1MF
100MF
100MF
100MF
10%
10%
20%
20%
20%
25V
25V
6.3V
6.3V
6.3V
C204
C205
C206
C207
C208
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
100MF
100MF
100MF
100MF
20%
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C209
C210
C211
C212
C213
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
100MF
100MF
100MF
100MF
20%
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C214
C215
C216
C217
C218
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
100MF
100MF
100MF
100MF
20%
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C219
C220
C231
1-126-392-11 ELECT CHIP
1-126-392-11 ELECT CHIP
1-126-392-11 ELECT CHIP
100MF
100MF
100MF
20%
20%
20%
6.3V
6.3V
6.3V
50V
50V
16V
50V
50V
9-1
BC
REF NO.
PART NO.
C232
C233
1-126-392-11 ELECT CHIP
1-126-392-11 ELECT CHIP
100MF
100MF
20%
20%
6.3V
6.3V
C234
C235
C236
C237
C241
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
1-126-392-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
100MF
100MF
100MF
100MF
20%
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C242
C243
C244
C245
C246
1-126-392-11
1-126-168-11
1-126-392-11
1-126-392-11
1-126-392-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
1000MF
100MF
100MF
100MF
20%
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C247
C248
C251
C252
C271
1-126-397-11
1-126-392-11
1-126-397-11
1-126-396-11
1-126-396-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
33MF
100MF
33MF
47MF
47MF
20%
20%
20%
20%
20%
25V
6.3V
25V
16V
16V
C281
C291
C301
C302
C303
1-126-392-11
1-126-396-11
1-163-031-11
1-163-031-11
1-163-031-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
47MF
0.01MF
0.01MF
0.01MF
20%
20%
6.3V
16V
50V
50V
50V
C304
C305
C306
C307
C308
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C309
C310
C311
C312
C313
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C314
C315
C316
C317
C318
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C319
C320
C321
C322
C323
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C324
C325
C326
C327
C328
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C329
C330
C331
C332
C333
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C334
C335
C336
C337
C338
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C339
1-163-031-11 CERAMIC CHIP
0.01MF
50V
9-2
DESCRIPTION
REMARK
REF NO.
PART NO.
DESCRIPTION
REMARK
C340
C341
C342
C343
1-163-031-11
1-135-216-11
1-135-216-11
1-135-216-11
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
0.01MF
10MF
10MF
10MF
C344
C351
C352
C357
C358
1-135-216-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10MF
0.01MF
0.01MF
0.01MF
0.01MF
C359
C360
C362
C363
C364
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C365
C366
C367
C368
C369
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C370
C371
C372
C373
C374
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C375
C376
C377
C378
C379
1-163-031-11
1-163-031-11
1-164-505-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
2.2MF
0.01MF
0.01MF
50V
50V
16V
50V
50V
C380
C381
C382
C391
C392
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C393
C394
C401
C402
C403
1-163-031-11
1-163-031-11
1-163-251-11
1-163-251-11
1-126-394-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.01MF
0.01MF
100PF
100PF
10MF
50V
50V
50V
50V
16V
C404
C405
C406
C407
C551
1-126-390-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22MF
0.01MF
0.01MF
0.01MF
0.01MF
C552
C553
C554
C555
C556
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C557
C558
C916
C918
1-163-031-11
1-163-031-11
1-126-397-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.01MF
0.01MF
33MF
0.01MF
50V
50V
25V
50V
20%
20%
20%
20%
5%
5%
20%
20%
20%
<CONNECTOR>
CN1
CN2
CN3
CN4
1-774-523-11
1-774-523-11
1-565-269-11
1-565-269-11
PIN, CONNECTOR (PC BOARD) 64P
PIN, CONNECTOR (PC BOARD) 64P
SOCKET, CONNECTOR (D-DUB,L) 9P
SOCKET, CONNECTOR (D-DUB,L) 9P
50V
10V
10V
10V
10V
50V
50V
50V
50V
6.3V
50V
50V
50V
50V
BC
REF NO.
PART NO.
DESCRIPTION
CN5
1-565-269-11 SOCKET, CONNECTOR (D-DUB,L) 9P
CN6
CN7
1-565-269-11 SOCKET, CONNECTOR (D-DUB,L) 9P
* 1-784-403-11 CONNECTOR, BOARD TO BOARD 40P
REMARK
REF NO.
PART NO.
DESCRIPTION
D558
D559
8-719-037-22 DIODE RD12SB-T1
8-719-037-22 DIODE RD12SB-T1
D560
D561
8-719-037-22 DIODE RD12SB-T1
8-719-037-22 DIODE RD12SB-T1
REMARK
<DIODE>
<FILTER>
D1
D2
D3
D4
D5
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
D6
D7
D8
D9
D10
8-719-037-22
8-719-037-22
8-719-037-22
8-719-037-22
8-719-037-22
DIODE RD12SB-T1
DIODE RD12SB-T1
DIODE RD12SB-T1
DIODE RD12SB-T1
DIODE RD12SB-T1
D11
D12
D13
D21
D22
8-719-037-22
8-719-158-19
8-719-404-49
8-719-158-19
8-719-158-19
DIODE RD12SB-T1
DIODE RD6.2SB
DIODE MA111
DIODE RD6.2SB
DIODE RD6.2SB
D23
D24
D29
D30
D31
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
D32
D33
D34
D35
D36
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
D37
D38
D39
D40
D41
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
D103
D104
D105
D106
D107
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
D108
D109
D111
D112
D113
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
D114
D115
D401
D402
D403
8-719-158-19
8-719-158-19
8-719-404-49
8-719-404-49
8-719-158-19
DIODE RD6.2SB
DIODE RD6.2SB
DIODE MA111
DIODE MA111
DIODE RD6.2SB
D550
D551
D552
D553
D554
8-719-037-22
8-719-037-22
8-719-037-22
8-719-037-22
8-719-037-22
DIODE RD12SB-T1
DIODE RD12SB-T1
DIODE RD12SB-T1
DIODE RD12SB-T1
DIODE RD12SB-T1
D555
D556
D557
8-719-037-22 DIODE RD12SB-T1
8-719-037-22 DIODE RD12SB-T1
8-719-037-22 DIODE RD12SB-T1
FL1
FL2
FL3
FL5
FL6
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
1-236-071-11
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
ENCAPSULATED COMPONENT
FL7
FL8
FL9
FL10
FL200
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
1-236-071-11
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
ENCAPSULATED COMPONENT
FL201
FL202
FL203
FL204
FL205
1-236-071-11
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
ENCAPSULATED COMPONENT
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FL210
FL211
FL212
FL213
FL214
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FL220
FL221
FL222
FL223
FL551
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FL552
FL553
FL554
FL555
FL556
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FL557
FL558
FL562
FL563
FL564
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
1-239-183-11
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FILTER, EMI
FL566
FL567
FL568
1-239-183-11 FILTER, EMI
1-239-183-11 FILTER, EMI
1-239-183-11 FILTER, EMI
<IC>
IC1
IC2
IC3
IC4
IC5
8-759-530-79
8-759-346-07
8-759-395-43
8-752-383-61
8-752-381-84
IC HD6435368AG14M
IC MM1026BFB
IC CAT28F020P-15
IC CXK58257CM-70LL-T6
IC CXD1095BQ
IC6
IC7
IC8
IC9
IC10
8-752-381-84
8-759-327-69
8-759-925-75
8-759-082-59
8-759-186-47
IC CXD1095BQ
IC µPD6453GT-101-E1
IC SN74HC05ANS
IC TC7W32FU
IC TC74VHC138F
IC11
IC12
8-759-981-48 IC TL082M
8-759-186-44 IC TC74VHC125F
9-3
BC
REF NO.
PART NO.
DESCRIPTION
IC13
IC14
IC15
8-759-186-47 IC TC74VHC138F
8-759-289-43 IC LTC490CS8
8-759-081-46 IC TC74VHCU04F
IC16
IC17
IC19
IC20
IC21
8-759-186-43
8-759-925-73
8-759-236-19
8-759-236-19
8-759-236-19
IC TC74VHC123AF
IC SN74HC03NS
IC TC74HC151AF(EL)
IC TC74HC151AF(EL)
IC TC74HC151AF(EL)
IC22
IC23
IC24
IC25
IC26
8-759-346-05
8-759-346-05
8-759-346-05
8-759-289-45
8-759-289-45
IC µPD71051GU-10-E2
IC µPD71051GU-10-E2
IC µPD71051GU-10-E2
IC LTC485CS8
IC LTC485CS8
IC27
IC28
IC29
IC30
IC31
8-759-252-59
8-759-252-59
8-759-186-77
8-759-186-24
8-759-081-46
IC MAX202CSE
IC MAX202CSE
IC TC74VHC541F
IC TC74VHC4040F(EL)
IC TC74VHCU04F
IC32
IC33
IC34
IC35
IC36
8-759-925-75
8-759-925-75
8-759-007-56
8-759-186-77
8-759-252-59
IC SN74HC05ANS
IC SN74HC05ANS
IC MC74HC30F
IC TC74VHC541F
IC MAX202CSE
IC37
IC51
IC52
IC61
IC62
8-759-182-91
8-759-700-65
8-759-144-82
8-759-186-43
8-759-195-02
IC PQ12TZ5U
IC NJM79L05A
IC µPC2405HF
IC TC74VHC123AF
IC TC7S86F-TE85L
IC63
IC104
IC105
IC106
IC109
8-759-011-65
8-759-186-24
8-752-357-15
8-759-186-53
8-752-334-64
IC MC74HC4053F
IC TC74VHC4040F(EL)
IC CXD2343S
IC TC74VHC163F
IC CXD1171M
IC110
IC111
IC113
IC114
IC115
8-759-236-55
8-759-011-65
8-759-186-39
8-759-295-09
8-759-185-64
IC TC74HC166AF(EL)
IC MC74HC4053F
IC TC74VHC74F
IC TLC2932IPW
IC TC74VHC10F(EL)
IC116
IC117
IC119
IC120
IC121
8-759-011-65
8-759-081-42
8-759-011-65
8-752-321-16
8-759-081-46
IC MC74HC4053F
IC TC74VHC00F
IC MC74HC4053F
IC CXD1030M
IC TC74VHCU04F
IC122
IC123
IC124
IC125
IC401
8-759-081-44
8-759-186-39
8-759-328-12
8-759-925-75
8-759-988-13
IC TC74VHC04F
IC TC74VHC74F
IC Z8622812PSC
IC SN74HC05ANS
IC LM393PS
REMARK
PART NO.
DESCRIPTION
REMARK
<COIL>
L1
L201
1-410-202-51 INDUCTOR CHIP
1-412-537-31 INDUCTOR
6.8µH
100µH
<FILTER>
LPF101
1-239-289-11 FILTER, LOW PASS
<TRANSISTOR>
Q1
Q2
Q3
Q4
Q5
1-801-806-11
8-729-901-06
8-729-901-06
1-801-806-11
1-801-806-11
TRANSISTOR DTC144EK-T146
TRANSISTOR DTA144EK
TRANSISTOR DTA144EK
TRANSISTOR DTC144EK-T146
TRANSISTOR DTC144EK-T146
Q6
Q7
Q8
Q9
Q10
8-729-122-13
8-729-122-13
1-801-806-11
8-729-921-12
1-801-806-11
TRANSISTOR 2SA1221-K
TRANSISTOR 2SA1221-K
TRANSISTOR DTC144EK-T146
TRANSISTOR 2SD1834
TRANSISTOR DTC144EK-T146
Q51
Q52
Q103
Q104
Q106
8-729-120-28
8-729-120-28
8-729-901-06
8-729-901-06
8-729-216-22
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR DTA144EK
TRANSISTOR DTA144EK
TRANSISTOR 2SA1162-G
Q107
Q108
Q109
Q110
Q111
8-729-120-28
8-729-120-28
8-729-216-22
8-729-901-06
8-729-120-28
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SA1162-G
TRANSISTOR DTA144EK
TRANSISTOR 2SC1623-L5L6
Q112
Q113
Q114
Q115
Q116
8-729-120-28
8-729-120-28
8-729-901-06
8-729-120-28
1-801-806-11
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR DTA144EK
TRANSISTOR 2SC1623-L5L6
TRANSISTOR DTC144EK-T146
Q151
Q152
Q401
Q402
Q403
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
8-729-921-12
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SD1834
<RESISTOR>
<CHIP CONDUCTOR>
JR14
JR15
JR114
JR115
JR116
1-216-296-91
1-216-295-91
1-216-296-91
1-216-296-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR117
JR118
JR119
1-216-296-91 SHORT
1-216-296-91 SHORT
1-216-296-91 SHORT
0
0
0
9-4
REF NO.
R1
R2
R3
R4
R5
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R6
R7
R8
R9
R10
1-216-073-00
1-216-097-91
1-216-097-91
1-216-097-91
1-216-121-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
100K
100K
100K
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R11
R12
R13
R14
R15
1-216-073-00
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R16
R17
R18
1-216-073-00 RES,CHIP
1-216-073-00 RES,CHIP
1-216-057-00 RES,CHIP
10K
10K
2.2K
5%
5%
5%
1/10W
1/10W
1/10W
BC
REF NO.
PART NO.
DESCRIPTION
REMARK
R19
R20
1-216-069-00 RES,CHIP
1-216-065-91 RES,CHIP
6.8K
4.7K
5%
5%
1/10W
1/10W
R21
R22
R23
R24
R25
1-216-077-00
1-216-073-00
1-216-651-11
1-216-651-11
1-216-651-11
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
10K
1K
1K
1K
5%
5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R26
R27
R28
R29
R31
1-216-651-11
1-216-049-91
1-216-049-91
1-216-073-00
1-216-121-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
1K
10K
1M
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R32
R33
R34
R35
R36
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-057-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R37
R38
R41
R42
R43
1-216-057-00
1-216-057-00
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
2.2K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R44
R45
R46
R47
R48
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R51
R52
R53
R54
R55
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R56
R57
R58
R59
R60
1-216-073-00
1-216-049-91
1-216-049-91
1-216-049-91
1-216-045-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
1K
1K
1K
680
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R61
R62
R63
R64
R69
R70
1-216-047-91
1-216-053-00
1-216-057-00
1-216-069-00
1-216-295-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
SHORT
RES,CHIP
820
1.5K
2.2K
6.8K
0
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
5%
1/10W
R71
R72
R73
R74
R75
1-216-049-91
1-216-655-11
1-216-097-91
1-216-073-00
1-216-073-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1.5K
100K
10K
10K
5%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R76
R77
R84
R85
R86
1-216-073-00
1-216-073-00
1-216-033-00
1-216-033-00
1-216-033-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
220
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R87
R88
R89
R90
R91
1-216-033-00
1-216-033-00
1-216-033-00
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
220
220
220
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
REF NO.
PART NO.
DESCRIPTION
REMARK
R92
R93
R94
R95
R96
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R97
R101
R102
R103
R104
1-216-097-91
1-216-669-11
1-216-097-91
1-216-059-00
1-216-691-11
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
100K
5.6K
100K
2.7K
47K
5%
0.50%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R105
R106
R109
R110
R111
1-216-661-11
1-216-059-00
1-216-073-00
1-216-079-00
1-216-061-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.7K
2.7K
10K
18K
3.3K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R112
R113
R114
R115
R116
1-216-065-91
1-216-061-00
1-216-634-11
1-216-049-91
1-216-081-00
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
4.7K
3.3K
200
1K
22K
5%
5%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R117
R118
R119
R120
R121
1-216-073-00
1-216-061-00
1-216-073-00
1-216-073-00
1-216-057-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
3.3K
10K
10K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R122
R123
R124
R125
R126
1-216-077-00
1-216-065-91
1-216-061-00
1-216-065-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
15K
4.7K
3.3K
4.7K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R127
R128
R129
R130
R131
1-216-049-91
1-216-057-00
1-216-065-91
1-216-097-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
2.2K
4.7K
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R132
R133
R134
R135
R136
1-216-081-00
1-216-065-91
1-216-097-91
1-216-025-91
1-216-081-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22K
4.7K
100K
100
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R137
R138
R139
R140
R141
1-216-025-91
1-216-081-00
1-216-065-91
1-216-097-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
22K
4.7K
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R151
R152
R153
R154
R155
1-216-081-00
1-216-081-00
1-216-057-00
1-216-057-00
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22K
22K
2.2K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R157
R159
R189
R191
R192
1-216-069-00
1-216-133-00
1-216-073-00
1-216-121-91
1-216-121-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
6.8K
3.3M
10K
1M
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R193
R201
R202
R203
1-216-121-91
1-216-073-00
1-216-041-00
1-216-081-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1M
10K
470
22K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
9-5
BC BK
REF NO.
PART NO.
DESCRIPTION
REMARK
R204
1-216-077-00 RES,CHIP
15K
5%
1/10W
R300
R301
R302
R303
R311
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R312
R313
R314
R401
R402
1-216-025-91
1-216-025-91
1-216-025-91
1-216-065-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
100
100
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R403
R404
R405
R406
R407
1-217-671-11
1-217-671-11
1-217-671-11
1-216-073-00
1-216-061-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1
1
1
10K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R408
R409
R410
R411
R551
1-216-073-00
1-216-073-00
1-216-065-91
1-216-097-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
4.7K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R552
R553
R554
R555
R556
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R557
R558
1-216-049-91 RES,CHIP
1-216-049-91 RES,CHIP
1K
1K
5%
5%
1/10W
1/10W
<VARIABLE RESISTOR>
RV101
1-238-787-11 RES, ADJ, CERMET 10K
REF NO.
PART NO.
DESCRIPTION
REMARK
* A-1135-921-A BK COMPL (20G1)
****************
* A-1135-941-A BK COMPLE (14G1/14G5)
****************
* X-4033-105-1
* 3-648-057-00
* 4-050-814-01
* 4-053-411-01
* 4-057-770-01
PANEL (BK) ASSY, CONNECTOR
NUT (ISO-4), U
SHIELD, PWB
SHIELD (BK), PWB (14G1/14G5)
INSULATOR
4-382-854-01
4-623-699-01
* 4-625-464-01
7-682-566-04
7-682-647-09
SCREW (M3X8), P, SW (+)(14G1/14G5)
SCREW (3X5)
SUPPORT, FITTING, MB
SCREW +B 4X20
SCREW +PS 3X6
7-685-872-09 SCREW +BVTT 3X8 (S)
<CAPACITOR>
C1
C3
C5
C7
C8
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-126-396-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.01MF
0.01MF
0.01MF
0.01MF
47MF
20%
50V
50V
50V
50V
16V
C9
C11
C12
C13
C14
1-163-031-11
1-126-396-11
1-126-396-11
1-126-396-11
1-126-397-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
0.01MF
47MF
47MF
47MF
33MF
20%
20%
20%
20%
50V
16V
16V
16V
25V
C15
C100
C101
C102
C103
1-163-031-11
1-163-227-11
1-163-229-11
1-115-155-11
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.01MF
10PF
12PF
22MF
0.047MF
0.5PF
5%
20%
10%
50V
50V
50V
16V
25V
C104
C122
C128
C129
C130
1-163-037-11
1-126-396-11
1-164-505-11
1-164-505-11
1-164-505-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022MF 10%
47MF
20%
2.2MF
2.2MF
2.2MF
C131
C140
C141
C142
C143
1-163-087-00
1-163-031-11
1-163-031-11
1-163-809-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4PF
0.25PF 50V
0.01MF
50V
0.01MF
50V
0.047MF 10% 25V
0.01MF 10% 50V
C144
C145
C146
C147
C154
1-163-031-11
1-163-031-11
1-126-392-11
1-126-392-11
1-126-390-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
0.01MF
0.01MF
100MF
100MF
22MF
20%
20%
20%
C160
C161
C162
C163
C164
1-163-031-11
1-163-031-11
1-163-249-11
1-163-091-00
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
82PF
8PF
0.01MF
50V
50V
5%
50V
0.25PF 50V
50V
C165
C166
C167
C168
C169
1-164-222-11
1-164-700-11
1-164-505-11
1-163-075-00
1-163-075-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22MF
0.68MF
2.2MF
0.047MF 10%
0.047MF 10%
<RELAY>
RY401
1-515-716-11 RELAY (TQ2-5V)
<TEST PIN>
TP1
TP3
TP5
TP6
TP7
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
PIN, POST
PIN, POST
PIN, POST
PIN, POST
PIN, POST
TP8
TP9
TP10
TP11
TP12
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
PIN, POST
PIN, POST
PIN, POST
PIN, POST
PIN, POST
TP13
1-537-864-11 PIN, POST
<CRYSTAL>
X1
X2
X101
X102
X103
1-767-892-21
1-760-464-11
1-767-655-21
1-767-891-21
1-760-429-11
VIBRATOR, CRYSTAL (20MHz)
VIBRATOR, CRYSTAL (4.9152MHz)
VIBRATOR, CRYSTAL (14.31818MHz)
VIBRATOR, CRYSTAL (14.1875MHz)
VIBRATOR, CRYSTAL (14.5MHz)
*************************************************************
9-6
50V
16V
16V
16V
16V
50V
50V
6.3V
6.3V
6.3V
25V
16V
16V
25V
25V
BK
REF NO.
PART NO.
DESCRIPTION
REMARK
C170
C171
C172
C173
C174
1-164-336-11
1-163-031-11
1-104-823-11
1-164-005-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.33MF
0.01MF
47MF
0.47MF
2.2MF
20%
25V
50V
16V
25V
16V
C175
C176
C177
C178
C179
1-164-505-11
1-163-809-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
0.047MF 10%
0.01MF
0.01MF
0.01MF
16V
25V
50V
50V
50V
C180
C181
C182
C183
C187
1-163-031-11
1-164-232-11
1-163-809-11
1-163-033-91
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF 10%
0.047MF 10%
0.022MF
0.01MF
50V
50V
25V
50V
50V
C188
C189
C190
C191
C192
1-163-038-11
1-163-031-11
1-164-222-11
1-163-251-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.01MF
0.22MF
100PF
0.01MF
25V
50V
25V
50V
50V
C193
C194
C195
C196
C197
1-163-035-00
1-107-364-11
1-164-505-11
1-107-943-11
1-163-031-11
CERAMIC CHIP
MYLAR
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.047MF
0.01MF 10%
2.2MF
10MF
20%
0.01MF
50V
200V
16V
160V
50V
C198
C199
C200
C201
C202
1-163-031-11
1-163-031-11
1-164-505-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
2.2MF
0.01MF
0.01MF
50V
50V
16V
50V
50V
C203
C204
C220
C222
C230
1-163-031-11
1-163-031-11
1-163-127-00
1-163-031-11
1-126-392-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.01MF
0.01MF
270PF
0.01MF
100MF
50V
50V
50V
50V
6.3V
C231
C232
C240
C241
C300
1-126-391-11
1-126-391-11
1-163-031-11
1-163-085-00
1-163-227-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47MF
47MF
0.01MF
2PF
10PF
20%
20%
C301
C302
C303
C304
C305
1-163-229-11
1-115-155-11
1-164-505-11
1-163-809-11
1-163-037-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
12PF
22MF
2.2MF
0.047MF
0.022MF
5%
20%
10%
10%
50V
16V
16V
25V
50V
C307
C308
C309
C310
C311
1-164-505-11
1-164-700-11
1-163-809-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
0.68MF
0.047MF 10%
0.01MF
0.01MF
16V
16V
25V
50V
50V
C322
C323
C324
C326
C327
1-126-392-11
1-164-505-11
1-163-031-11
1-164-222-11
1-163-809-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
20%
2.2MF
0.01MF
0.22MF
0.047MF 10%
6.3V
16V
50V
25V
25V
C328
C329
C330
C331
1-164-505-11
1-164-505-11
1-164-505-11
1-163-087-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
2.2MF
2.2MF
4PF
5%
10%
5%
20%
6.3V
6.3V
50V
0.25PF 50V
0.5PF 50V
16V
16V
16V
0.25PF 50V
REF NO.
PART NO.
DESCRIPTION
REMARK
C350
1-163-031-11 CERAMIC CHIP
0.01MF
50V
C351
C352
C353
C354
C355
1-163-031-11
1-163-809-11
1-164-232-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.047MF 10%
0.01MF 10%
0.01MF
0.01MF
50V
25V
50V
50V
50V
C356
C357
C360
C361
C362
1-126-392-11
1-126-392-11
1-163-031-11
1-163-031-11
1-163-249-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
100MF
0.01MF
0.01MF
82PF
20%
20%
6.3V
6.3V
50V
50V
50V
C363
C374
C375
C376
C377
1-163-091-00
1-164-222-11
1-164-700-11
1-164-505-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
8PF
0.22MF
0.68MF
2.2MF
0.01MF
0.25PF 50V
25V
16V
16V
50V
C378
C379
C380
C381
C382
1-163-075-00
1-163-075-00
1-164-336-11
1-163-031-11
1-104-823-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.047MF 10%
0.047MF 10%
0.33MF
0.01MF
47MF
20%
25V
25V
25V
50V
16V
C383
C384
C385
C386
C387
1-164-005-11
1-164-505-11
1-164-505-11
1-163-809-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47MF
2.2MF
2.2MF
0.047MF 10%
0.01MF
25V
16V
16V
25V
50V
C388
C389
C390
C391
C392
1-163-031-11
1-163-031-11
1-163-031-11
1-164-232-11
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF 10%
0.047MF 10%
50V
50V
50V
50V
25V
C393
C397
C398
C399
C400
1-163-033-91
1-163-031-11
1-163-038-11
1-163-031-11
1-164-222-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022MF
0.01MF
0.1MF
0.01MF
0.22MF
50V
50V
25V
50V
25V
C401
C402
C403
C404
C405
1-163-251-11
1-164-232-11
1-163-035-00
1-107-364-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
MYLAR
CERAMIC CHIP
100PF
5%
0.01MF 10%
0.047MF
0.01MF 10%
2.2MF
50V
50V
50V
200V
16V
C406
C407
C409
C410
C411
1-107-943-11
1-163-031-11
1-164-505-11
1-163-031-11
1-163-031-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10MF
0.01MF
2.2MF
0.01MF
0.01MF
160V
50V
16V
50V
50V
C412
C420
C421
C422
C430
1-163-031-11
1-163-127-00
1-126-390-11
1-163-031-11
1-126-392-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
0.01MF
270PF
22MF
0.01MF
100MF
C431
C432
C440
C451
C500
1-126-391-11
1-126-391-11
1-163-031-11
1-163-085-00
1-163-227-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47MF
47MF
0.01MF
2PF
10PF
20%
20%
C501
C502
1-163-229-11 CERAMIC CHIP
1-115-155-11 ELECT CHIP
12PF
22MF
5%
20%
5%
20%
5%
20%
20%
50V
50V
6.3V
50V
6.3V
6.3V
6.3V
50V
0.25PF 50V
0.5PF 50V
50V
16V
9-7
BK
REF NO.
PART NO.
C503
C504
C505
1-164-505-11 CERAMIC CHIP
1-163-809-11 CERAMIC CHIP
1-163-037-11 CERAMIC CHIP
2.2MF
0.047MF 10%
0.022MF 10%
16V
25V
50V
C507
C508
C509
C510
C520
1-164-505-11
1-164-505-11
1-164-700-11
1-163-809-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
2.2MF
0.68MF
0.047MF 10%
2.2MF
16V
16V
16V
25V
16V
C523
C524
C526
C527
C528
1-164-505-11
1-163-031-11
1-164-222-11
1-163-809-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
0.01MF
0.22MF
0.047MF 10%
2.2MF
16V
50V
25V
25V
16V
C529
C530
C531
C540
C541
1-164-505-11
1-164-505-11
1-163-087-00
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
2.2MF
4PF
0.01MF
0.01MF
C542
C543
C544
C545
C546
1-163-809-11
1-164-232-11
1-163-031-11
1-163-031-11
1-126-392-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.047MF 10%
0.01MF 10%
0.01MF
0.01MF
100MF
20%
25V
50V
50V
50V
6.3V
C547
C548
C549
C560
C561
1-126-392-11
1-126-392-11
1-126-392-11
1-163-031-11
1-163-031-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
100MF
100MF
0.01MF
0.01MF
20%
20%
20%
6.3V
6.3V
6.3V
50V
50V
C562
C563
C567
C568
C569
1-163-249-11
1-163-091-00
1-164-222-11
1-164-700-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
82PF
8PF
0.22MF
0.68MF
2.2MF
5%
50V
0.25PF 50V
25V
16V
16V
C570
C571
C572
C573
C574
1-163-031-11
1-163-075-00
1-163-075-00
1-164-336-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.047MF 10%
0.047MF 10%
0.33MF
0.01MF
50V
25V
25V
25V
50V
C575
C576
C577
C578
C579
1-104-823-11
1-164-005-11
1-164-505-11
1-164-505-11
1-163-809-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47MF
20%
0.47MF
2.2MF
2.2MF
0.047MF 10%
16V
25V
16V
16V
25V
C580
C581
C582
C583
C584
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
10%
50V
50V
50V
50V
50V
C585
C586
C590
C591
C592
1-163-809-11
1-163-033-91
1-163-031-11
1-163-038-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047MF 10%
0.022MF
0.01MF
0.1MF
0.01MF
25V
50V
50V
25V
50V
C593
C594
C595
C596
C597
1-164-222-11
1-163-251-11
1-164-232-11
1-163-035-00
1-107-364-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
MYLAR
0.22MF
100PF
5%
0.01MF 10%
0.047MF
0.01MF 10%
25V
50V
50V
50V
200V
9-8
DESCRIPTION
REMARK
16V
16V
0.25PF 50V
50V
50V
REF NO.
PART NO.
DESCRIPTION
REMARK
C598
C599
C600
C601
C602
1-164-505-11
1-107-943-11
1-163-031-11
1-163-031-11
1-164-505-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
10MF
0.01MF
0.01MF
2.2MF
C603
C604
C605
C620
C621
1-163-031-11
1-164-505-11
1-163-031-11
1-163-127-00
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
2.2MF
0.01MF
270PF
2.2MF
C622
C630
C631
C632
C640
1-163-031-11
1-126-392-11
1-126-391-11
1-126-391-11
1-163-031-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.01MF
100MF
47MF
47MF
0.01MF
C641
C700
C701
C702
C703
1-163-087-00
1-163-037-11
1-163-037-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4PF
0.25PF 50V
0.022MF 10% 50V
0.022MF 10% 50V
0.01MF
50V
0.01MF
50V
C704
C705
C706
C707
C708
1-126-391-11
1-163-031-11
1-164-505-11
1-163-031-11
1-115-153-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
47MF
0.01MF
2.2MF
0.01MF
4.7MF
C712
C713
C714
C728
C729
1-164-505-11
1-164-505-11
1-164-505-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
2.2MF
2.2MF
0.01MF
0.01MF
C734
C751
C782
C783
C800
1-163-031-11
1-126-396-11
1-163-031-11
1-163-031-11
1-163-229-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
47MF
0.01MF
0.01MF
12PF
C801
C802
C803
C804
C805
1-163-229-11
1-163-031-11
1-163-031-11
1-115-155-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
12PF
0.01MF
0.01MF
22MF
0.01MF
C806
C807
C808
C809
C810
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
C812
C813
C814
C815
C816
1-163-031-11
1-126-394-11
1-163-251-11
1-163-257-11
1-163-251-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
10MF
100PF
180PF
100PF
C817
C818
C819
C820
C821
1-164-346-11
1-126-390-11
1-163-038-11
1-163-038-11
1-163-038-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1MF
22MF
0.1MF
0.1MF
0.1MF
C822
C823
C824
C825
1-163-038-11
1-128-235-11
1-164-346-11
1-163-121-00
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.47MF
1MF
150PF
20%
5%
20%
20%
20%
20%
20%
16V
160V
50V
50V
16V
50V
16V
50V
50V
16V
50V
6.3V
6.3V
6.3V
50V
6.3V
50V
16V
50V
16V
16V
16V
16V
50V
50V
20%
5%
5%
20%
50V
16V
50V
50V
50V
50V
50V
50V
16V
50V
50V
50V
50V
50V
50V
20%
5%
5%
5%
20%
20%
5%
50V
16V
50V
50V
50V
16V
6.3V
25V
25V
25V
25V
50V
16V
50V
BK
REF NO.
PART NO.
DESCRIPTION
REMARK
C826
1-163-113-00 CERAMIC CHIP
68PF
5%
50V
C827
C828
C829
C830
C831
1-163-031-11
1-163-133-00
1-163-019-00
1-163-133-00
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
470PF
0.0068MF
470PF
0.001MF
5%
10%
5%
10%
50V
50V
50V
50V
50V
C832
C833
C834
C835
C836
1-163-133-00
1-163-133-00
1-163-133-00
1-163-251-11
1-163-133-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
470PF
100PF
470PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C837
C838
C840
C841
C847
1-164-222-11
1-164-222-11
1-163-023-00
1-164-346-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22MF
0.22MF
0.015MF 10%
1MF
0.01MF
25V
25V
50V
16V
50V
C850
C851
C852
C853
C861
1-126-392-11
1-126-168-11
1-126-391-11
1-126-168-11
1-163-251-11
ELECT CHIP
ELECT
ELECT CHIP
ELECT
CERAMIC CHIP
100MF
1000MF
47MF
1000MF
100PF
6.3V
6.3V
6.3V
6.3V
50V
C863
C900
C901
C902
C903
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C904
C905
C907
C908
C909
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C910
C911
C914
C915
C917
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C918
C921
C924
C925
C926
1-163-037-11
1-163-031-11
1-126-391-11
1-126-391-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.022MF 10%
0.01MF
47MF
20%
47MF
20%
0.01MF
50V
50V
6.3V
6.3V
50V
C927
C928
C929
C930
C931
1-126-391-11
1-109-982-11
1-126-391-11
1-126-390-11
1-109-982-11
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
47MF
1MF
47MF
22MF
1MF
6.3V
10V
6.3V
6.3V
10V
C1000
C1001
C1002
C1003
C1004
1-163-031-11
1-126-392-11
1-163-031-11
1-163-031-11
1-164-505-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
100MF
0.01MF
0.01MF
2.2MF
C1005
C1006
C1007
C1008
C1009
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C1010
C1011
1-163-031-11 CERAMIC CHIP
1-164-505-11 CERAMIC CHIP
0.01MF
2.2MF
50V
16V
20%
20%
20%
20%
5%
20%
10%
20%
20%
10%
20%
50V
6.3V
50V
50V
16V
REF NO.
PART NO.
DESCRIPTION
REMARK
C1012
C1013
C1014
1-163-031-11 CERAMIC CHIP
1-163-031-11 CERAMIC CHIP
1-164-505-11 CERAMIC CHIP
0.01MF
0.01MF
2.2MF
50V
50V
16V
C1015
C1016
C1017
C1019
C1020
1-163-031-11
1-163-031-11
1-164-505-11
1-163-031-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
2.2MF
0.01MF
2.2MF
50V
50V
16V
50V
16V
C1021
C1022
C1023
C1024
C1025
1-163-031-11
1-163-031-11
1-164-505-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
2.2MF
0.01MF
0.01MF
50V
50V
16V
50V
50V
C1026
C1027
C1028
C1029
C1030
1-163-031-11
1-126-396-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
47MF
0.01MF
0.01MF
0.01MF
C1031
C1032
C1033
C1034
C1035
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C1036
C1037
C1038
C1039
C1200
1-163-031-11
1-164-505-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
2.2MF
0.01MF
0.01MF
0.01MF
50V
16V
50V
50V
50V
C1201
C1208
C1209
C1210
C1211
1-126-392-11
1-164-505-11
1-164-505-11
1-163-031-11
1-163-031-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
2.2MF
2.2MF
0.01MF
0.01MF
C1213
C1215
C1216
C1217
C1218
1-164-505-11
1-163-031-11
1-163-031-11
1-163-031-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
0.01MF
0.01MF
0.01MF
2.2MF
16V
50V
50V
50V
16V
C1222
C1223
C1224
C1225
C1227
1-164-505-11
1-164-505-11
1-163-031-11
1-163-031-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2MF
2.2MF
0.01MF
0.01MF
2.2MF
16V
16V
50V
50V
16V
C1229
C1230
C1231
C1235
C1236
1-163-031-11
1-163-031-11
1-163-031-11
1-164-505-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
2.2MF
2.2MF
50V
50V
50V
16V
16V
C1237
C1238
C1240
C1242
C1243
1-163-031-11
1-163-031-11
1-164-505-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
2.2MF
0.01MF
0.01MF
50V
50V
16V
50V
50V
C1244
C1245
C1246
C1247
C1248
1-163-031-11
1-163-031-11
1-163-031-11
1-126-396-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
47MF
0.01MF
50V
50V
50V
16V
50V
20%
20%
20%
50V
16V
50V
50V
50V
6.3V
16V
16V
50V
50V
9-9
BK
REF NO.
PART NO.
DESCRIPTION
REF NO.
PART NO.
IC3
IC101
IC102
8-759-701-88 IC NJM7912FA
8-759-011-65 IC MC74HC4053F
8-759-981-48 IC TL082M
<DIODE>
IC104
IC106
IC107
IC110
IC111
8-759-011-65
8-759-981-48
8-759-082-61
8-759-011-65
8-759-981-48
IC MC74HC4053F
IC TL082M
IC TC4W53FU
IC MC74HC4053F
IC TL082M
<CONNECTOR>
CN1
CN2
CN3
CN4
CN5
1-774-523-11
* 1-564-507-11
* 1-564-507-11
* 1-564-507-11
* 1-564-506-11
PIN, CONNECTOR (PC BOARD) 64P
PLUG, CONNECTOR 4P
PLUG, CONNECTOR 4P
PLUG, CONNECTOR 4P
PLUG, CONNECTOR 3P
REMARK
DESCRIPTION
D11
D12
D13
D14
D102
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
8-719-404-49
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE MA111
IC112
IC113
IC114
IC115
IC116
8-752-054-80
8-759-011-65
8-759-981-48
8-759-700-95
8-759-011-63
IC CXA1521M
IC MC74HC4053F
IC TL082M
IC NJM1496M
IC MC74HC4051F
D103
D164
D165
D166
D167
8-719-404-49
8-719-404-49
8-719-404-49
8-719-157-72
8-719-901-83
DIODE MA111
DIODE MA111
DIODE MA111
DIODE RD22M-B
DIODE 1SS83
IC117
IC118
IC119
IC121
IC122
8-759-011-65
8-759-981-48
8-759-346-42
8-759-981-48
8-759-981-48
IC MC74HC4053F
IC TL082M
IC TDA6101Q/N3
IC TL082M
IC TL082M
D168
D200
D201
D302
D303
8-719-901-83
8-719-404-49
8-719-106-16
8-719-404-49
8-719-404-49
DIODE 1SS83
DIODE MA111
DIODE RD6.8M-B1
DIODE MA111
DIODE MA111
IC123
IC124
IC126
IC127
IC128
8-759-981-48
8-759-011-65
8-759-011-65
8-759-981-48
8-759-100-96
IC TL082M
IC MC74HC4053F
IC MC74HC4053F
IC TL082M
IC µPC4558G2
D374
D375
D376
D377
D378
8-719-404-49
8-719-404-49
8-719-157-72
8-719-901-83
8-719-901-83
DIODE MA111
DIODE MA111
DIODE RD22M-B
DIODE 1SS83
DIODE 1SS83
IC129
IC131
IC300
IC301
IC302
8-759-988-13
8-759-058-64
8-759-981-48
8-759-011-65
8-759-981-48
IC LM393PS
IC TC7S32FU(TE85R)
IC TL082M
IC MC74HC4053F
IC TL082M
D400
D401
D502
D503
D567
8-719-404-49
8-719-106-16
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE RD6.8M-B1
DIODE MA111
DIODE MA111
DIODE MA111
IC303
IC304
IC305
IC306
IC307
8-752-054-80
8-759-011-65
8-752-053-21
8-759-981-48
8-759-082-61
IC CXA1521M
IC MC74HC4053F
IC CXA1211M
IC TL082M
IC TC4W53FU
D568
D569
D570
D571
D600
8-719-404-49
8-719-157-72
8-719-901-83
8-719-901-83
8-719-404-49
DIODE MA111
DIODE RD22M-B
DIODE 1SS83
DIODE 1SS83
DIODE MA111
IC310
IC311
IC312
IC313
IC314
8-759-011-65
8-759-981-48
8-752-054-80
8-759-011-65
8-759-981-48
IC MC74HC4053F
IC TL082M
IC CXA1521M
IC MC74HC4053F
IC TL082M
D601
D701
D802
D803
D804
8-719-106-16
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE RD6.8M-B1
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
IC315
IC316
IC317
IC318
IC319
8-759-700-95
8-759-011-63
8-759-011-65
8-759-981-48
8-759-346-42
IC NJM1496M
IC MC74HC4051F
IC MC74HC4053F
IC TL082M
IC TDA6101Q/N3
D900
D901
D902
D903
D904
8-719-158-19
8-719-404-49
8-719-404-49
8-719-404-49
8-719-920-76
DIODE RD6.2SB
DIODE MA111
DIODE MA111
DIODE MA111
DIODE 1S2076
IC320
IC321
IC322
IC323
IC324
8-759-981-48
8-759-981-48
8-759-981-48
8-759-981-48
8-759-011-65
IC TL082M
IC TL082M
IC TL082M
IC TL082M
IC MC74HC4053F
D905
8-719-404-49 DIODE MA111
IC325
IC326
IC327
IC328
IC329
8-759-082-61
8-759-011-65
8-759-981-48
8-759-100-96
8-759-988-13
IC TC4W53FU
IC MC74HC4053F
IC TL082M
IC µPC4558G2
IC LM393PS
IC331
IC500
IC501
IC502
IC503
8-759-058-64
8-759-011-65
8-759-011-65
8-759-981-48
8-752-054-80
IC TC7S32FU(TE85R)
IC MC74HC4053F
IC MC74HC4053F
IC TL082M
IC CXA1521M
<FILTER>
FL900
FL901
FL902
1-239-480-11 FILTER, EMI
1-239-480-11 FILTER, EMI
1-239-183-11 FILTER, EMI
<IC>
IC1
IC2
9-10
8-759-144-82 IC µPC2405HF
8-759-247-67 IC LM2990T-5.0
REMARK
BK
REF NO.
PART NO.
IC504
IC506
IC507
IC508
IC509
8-759-011-65
8-759-981-48
8-759-082-61
8-759-082-61
8-759-058-54
IC510
IC511
IC512
IC513
IC514
DESCRIPTION
REMARK
REF NO.
PART NO.
DESCRIPTION
REMARK
IC MC74HC4053F
IC TL082M
IC TC4W53FU
IC TC4W53FU
IC TC7S00FU(TE85R)
IC911
8-759-064-36 IC MB88346BPFV
IC912
8-759-082-59 IC TC7W32FU
8-759-011-65
8-759-981-48
8-752-054-80
8-759-011-65
8-759-981-48
IC MC74HC4053F
IC TL082M
IC CXA1521M
IC MC74HC4053F
IC TL082M
JR101
JR301
JR501
JR731
JR901
1-216-295-91
1-216-295-91
1-216-295-91
1-216-295-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
IC515
IC516
IC517
IC518
IC519
8-759-700-95
8-759-011-63
8-759-011-65
8-759-981-48
8-759-346-42
IC NJM1496M
IC MC74HC4051F
IC MC74HC4053F
IC TL082M
IC TDA6101Q/N3
JR903
1-216-295-91 SHORT
0
IC520
IC521
IC522
IC523
IC524
8-759-981-48
8-759-981-48
8-759-981-48
8-759-981-48
8-759-011-65
IC TL082M
IC TL082M
IC TL082M
IC TL082M
IC MC74HC4053F
IC525
IC526
IC527
IC528
IC529
8-759-082-61
8-759-011-65
8-759-981-48
8-759-100-96
8-759-988-13
IC TC4W53FU
IC MC74HC4053F
IC TL082M
IC µPC4558G2
IC LM393PS
IC531
IC700
IC701
IC702
IC703
8-759-058-64
8-759-981-48
8-759-011-65
8-759-011-65
8-759-988-13
IC TC7S32FU(TE85R)
IC TL082M
IC MC74HC4053F
IC MC74HC4053F
IC LM393PS
IC704
IC705
IC706
IC707
IC710
8-759-981-48
8-759-100-96
8-759-011-65
8-759-083-94
8-759-988-13
IC TL082M
IC µPC4558G2
IC MC74HC4053F
IC TC7W74FU
IC LM393PS
IC711
IC728
IC730
IC731
IC732
8-759-082-58
8-759-424-13
8-759-424-14
8-759-367-67
8-759-424-31
IC TC7W08FU
IC MC74HC00AFEL
IC MC74HC02AFEL
IC MC74HC14AFEL
IC MC74HC175FEL
IC734
IC735
IC736
IC800
IC801
8-759-424-18
8-759-424-14
8-759-424-14
8-759-011-65
8-759-038-15
IC MC74HC11FEL
IC MC74HC02AFEL
IC MC74HC02AFEL
IC MC74HC4053F
IC MC74HC4538AF
IC802
IC803
IC804
IC805
IC900
8-759-100-96
8-759-038-15
8-759-038-15
8-759-058-55
8-759-367-70
IC µPC4558G2
IC MC74HC4538AF
IC MC74HC4538AF
IC TC7S02FU-TE85L
IC MC74HC125AFEL
IC901
IC902
IC903
IC904
IC906
8-759-100-96
8-759-346-47
8-759-156-54
8-759-988-13
8-759-064-36
IC µPC4558G2
IC MB89613R-236
IC X25040SI
IC LM393PS
IC MB88346BPFV
IC907
IC908
IC909
IC910
8-759-064-36
8-759-064-36
8-759-064-36
8-759-064-36
IC MB88346BPFV
IC MB88346BPFV
IC MB88346BPFV
IC MB88346BPFV
<CHIP CONDUCTOR>
<TRANSISTOR>
Q100
Q101
Q102
Q103
Q104
8-729-112-65
8-729-027-38
8-729-107-31
8-729-112-65
8-729-107-31
TRANSISTOR 2SA1462-Y33
TRANSISTOR DTA144EKA-T146
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
Q105
Q106
Q107
Q108
Q140
8-729-107-31
8-729-112-65
8-729-120-28
8-729-120-28
8-729-107-31
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC3545-T43
Q141
Q142
Q143
Q144
Q164
8-729-107-31
8-729-107-31
8-729-112-65
8-729-112-65
8-729-107-31
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
Q165
Q166
Q167
Q168
Q169
8-729-120-28
8-729-120-28
8-729-107-31
8-729-112-65
8-729-107-31
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
Q170
Q171
Q172
Q174
Q175
8-729-920-59
8-729-920-59
8-729-920-59
8-729-107-31
8-729-112-65
TRANSISTOR IMX2-T109
TRANSISTOR IMX2-T109
TRANSISTOR IMX2-T109
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
Q176
Q177
Q178
Q190
Q200
8-729-107-31
8-729-033-31
8-729-033-31
1-801-806-11
8-729-107-31
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SK520K44K45-T1B
TRANSISTOR 2SK520K44K45-T1B
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC3545-T43
Q300
Q301
Q302
Q303
Q304
8-729-112-65
8-729-027-38
8-729-107-31
8-729-112-65
8-729-107-31
TRANSISTOR 2SA1462-Y33
TRANSISTOR DTA144EKA-T146
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
Q305
Q306
Q307
Q308
Q309
8-729-107-31
8-729-107-31
8-729-112-65
8-729-216-22
8-729-112-65
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1462-Y33
Q310
Q350
Q351
Q352
Q353
8-729-107-31
8-729-107-31
8-729-107-31
8-729-107-31
8-729-112-65
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
9-11
BK
REF NO.
PART NO.
Q354
Q374
Q375
Q376
Q377
8-729-112-65
8-729-107-31
8-729-120-28
8-729-120-28
8-729-107-31
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC3545-T43
Q378
Q379
Q380
Q381
Q382
8-729-112-65
8-729-107-31
8-729-920-59
8-729-920-59
8-729-920-59
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
TRANSISTOR IMX2-T109
TRANSISTOR IMX2-T109
TRANSISTOR IMX2-T109
Q384
Q385
Q386
Q387
Q388
8-729-107-31
8-729-112-65
8-729-107-31
8-729-033-31
8-729-033-31
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SK520K44K45-T1B
TRANSISTOR 2SK520K44K45-T1B
Q390
Q400
Q500
Q501
Q502
1-801-806-11
8-729-107-31
8-729-112-65
8-729-027-38
8-729-107-31
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR DTA144EKA-T146
TRANSISTOR 2SC3545-T43
Q503
Q504
Q505
Q506
Q507
8-729-112-65
8-729-107-31
8-729-107-31
8-729-112-65
8-729-120-28
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC1623-L5L6
Q510
Q540
Q541
Q542
Q543
8-729-107-31
8-729-107-31
8-729-107-31
8-729-107-31
8-729-112-65
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
Q544
Q567
Q568
Q569
Q570
8-729-112-65
8-729-107-31
8-729-920-59
8-729-120-28
8-729-107-31
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
TRANSISTOR IMX2-T109
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC3545-T43
Q571
Q572
Q573
Q574
Q575
8-729-112-65
8-729-107-31
8-729-920-59
8-729-920-59
8-729-920-59
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
TRANSISTOR IMX2-T109
TRANSISTOR IMX2-T109
TRANSISTOR IMX2-T109
Q577
Q578
Q579
Q580
Q581
8-729-107-31
8-729-112-65
8-729-107-31
8-729-033-31
8-729-033-31
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1462-Y33
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SK520K44K45-T1B
TRANSISTOR 2SK520K44K45-T1B
Q590
Q600
Q700
Q701
Q702
1-801-806-11
8-729-107-31
8-729-216-22
8-729-216-22
8-729-216-22
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC3545-T43
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
Q705
Q706
Q800
Q801
Q802
8-729-120-28
8-729-216-22
8-729-216-22
8-729-216-22
8-729-216-22
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
Q803
Q804
Q805
Q806
8-729-920-59
8-729-120-28
8-729-920-59
8-729-216-22
TRANSISTOR IMX2-T109
TRANSISTOR 2SC1623-L5L6
TRANSISTOR IMX2-T109
TRANSISTOR 2SA1162-G
9-12
DESCRIPTION
REMARK
REF NO.
PART NO.
DESCRIPTION
REMARK
Q807
8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q808
Q809
Q810
Q811
Q812
8-729-120-28
8-729-120-28
8-729-925-42
8-729-925-42
8-729-120-28
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR IMT2
TRANSISTOR IMT2
TRANSISTOR 2SC1623-L5L6
Q813
Q814
Q815
Q816
Q817
8-729-216-22
8-729-216-22
8-729-120-28
8-729-216-22
8-729-120-28
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC1623-L5L6
Q818
Q819
Q820
Q821
Q822
8-729-120-28
8-729-120-28
8-729-216-22
1-801-806-11
8-729-120-28
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SA1162-G
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC1623-L5L6
Q823
Q824
Q825
Q826
Q827
8-729-120-28
8-729-216-22
8-729-216-22
8-729-202-38
8-729-202-38
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC3326N-A
TRANSISTOR 2SC3326N-A
Q828
Q829
Q900
Q902
8-729-216-22
8-729-120-28
1-801-806-11
8-729-027-38
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC1623-L5L6
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTA144EKA-T146
<RESISTOR>
R10
R11
R12
R13
R14
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R20
R100
R101
R102
R103
1-249-400-11
1-216-085-00
1-216-107-00
1-216-049-91
1-216-097-91
CARBON
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
39
33K
270K
1K
100K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
R104
R105
R106
R107
R108
1-216-027-00
1-216-051-00
1-216-025-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
120
1.2K
100
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R109
R110
R111
R112
R113
1-216-009-00
1-216-009-00
1-216-657-11
1-216-663-11
1-216-025-91
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
22
22
1.8K
3.3K
100
5%
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R114
R115
R116
R117
R118
1-216-651-11
1-216-033-00
1-216-057-00
1-216-057-00
1-216-009-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
220
2.2K
2.2K
22
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R119
R121
R122
R123
R124
1-216-067-00
1-216-057-00
1-216-049-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
5.6K
2.2K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R125
1-216-115-00 RES,CHIP
560K
5%
1/10W
F
BK
REF NO.
PART NO.
DESCRIPTION
REMARK
R126
R140
R141
R142
1-216-109-00
1-216-638-11
1-216-674-11
1-216-647-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330K
300
9.1K
680
5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
R143
R144
R146
R147
R148
1-216-047-91
1-216-647-11
1-216-053-00
1-216-057-00
1-218-764-11
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
820
680
1.5K
2.2K
330K
5%
0.50%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R149
R150
R151
R152
R153
1-216-025-91
1-218-758-11
1-216-675-11
1-216-121-91
1-216-671-11
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
100
180K
10K
1M
6.8K
5%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R155
R156
R157
R158
R159
1-216-047-91
1-216-651-11
1-216-676-11
1-216-691-11
1-216-051-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
820
1K
11K
47K
1.2K
5%
0.50%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R160
R162
R163
R164
R165
1-216-025-91
1-216-049-91
1-216-073-00
1-216-633-11
1-216-627-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
100
1K
10K
180
100
5%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R166
R167
R168
R169
R170
1-216-057-00
1-216-057-00
1-216-049-91
1-216-053-00
1-216-654-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
2.2K
2.2K
1K
1.5K
1.3K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R171
R172
R173
R174
R175
1-216-679-11
1-216-049-91
1-216-025-91
1-216-033-00
1-216-065-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
15K
1K
100
220
4.7K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R176
R177
R178
R179
R180
1-216-073-00
1-216-658-11
1-216-662-11
1-216-025-91
1-216-657-11
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
10K
2K
3K
100
1.8K
5%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R181
R182
R183
R184
R185
1-216-653-11
1-216-067-00
1-216-025-91
1-216-051-00
1-216-073-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1.2K
5.6K
100
1.2K
10K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R186
R187
R188
R189
R190
1-216-073-00
1-216-679-11
1-216-049-91
1-216-025-91
1-216-073-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
15K
1K
100
10K
5%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R191
R192
R193
R194
R195
1-216-675-11
1-216-687-11
1-216-679-11
1-216-025-91
1-216-653-11
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
10K
33K
15K
100
1.2K
0.50%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R196
R197
R198
R199
R201
1-216-025-91
1-216-665-11
1-216-658-11
1-216-661-11
1-216-073-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
100
3.9K
2K
2.7K
10K
5%
0.50%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
REF NO.
PART NO.
DESCRIPTION
REMARK
R202
R203
R204
R205
R206
1-216-677-11
1-216-666-11
1-216-670-11
1-216-025-91
1-216-679-11
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
12K
4.3K
6.2K
100
15K
0.50%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R207
R208
R210
R211
R212
1-216-649-11
1-216-647-11
1-216-647-11
1-216-025-91
1-216-025-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
820
680
680
100
100
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R213
R214
R215
R216
R217
1-216-667-11
1-216-659-11
1-216-658-11
1-216-675-11
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
4.7K
2.2K
2K
10K
10K
0.50%
0.50%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R219
R221
R222
R223
R224
1-216-033-00
1-216-655-11
1-216-025-91
1-216-653-11
1-216-675-11
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
220
1.5K
100
1.2K
10K
5%
0.50%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R225
R226
R227
R228
R229
1-216-659-11
1-216-669-11
1-216-057-00
1-216-025-91
1-216-057-00
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
5.6K
2.2K
100
2.2K
0.50%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R230
R232
R236
R237
R238
1-216-073-00
1-216-073-00
1-216-095-00
1-216-065-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
82K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R239
R240
R241
R242
R243
1-216-671-11
1-216-669-11
1-216-651-11
1-216-073-00
1-216-672-11
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
6.8K
5.6K
1K
10K
7.5K
0.50%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R244
R245
R246
R247
R248
1-218-766-11
1-216-033-00
1-216-669-11
1-216-669-11
1-214-903-31
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL
390K
220
5.6K
5.6K
39K
0.50%
5%
0.50%
0.50%
1%
1/10W
1/10W
1/10W
1/10W
1/2W
R249
R250
R251
R252
R253
1-216-669-11
1-216-033-00
1-216-695-11
1-216-689-11
1-216-093-00
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
5.6K
220
68K
39K
68K
0.50%
5%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R254
R255
R256
R257
R258
1-216-055-00
1-216-073-00
1-216-073-00
1-219-743-11
1-216-699-11
RES,CHIP
RES,CHIP
RES,CHIP
CARBON
METAL CHIP
1.8K
10K
10K
100
100K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/2W
1/10W
R259
R272
R273
R287
R288
1-216-073-00
1-216-025-91
1-216-073-00
1-216-033-00
1-216-033-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
100
10K
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R300
R301
R302
R303
1-216-085-00
1-216-107-00
1-216-049-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
33K
270K
1K
100K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
9-13
BK
REF NO.
PART NO.
R304
1-216-009-00 RES,CHIP
22
5%
1/10W
R305
R306
R307
R308
R309
1-216-051-00
1-216-025-91
1-216-049-91
1-216-049-91
1-216-009-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1.2K
100
1K
1K
22
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R310
R311
R312
R313
R314
1-216-009-00
1-216-697-91
1-216-657-11
1-216-663-11
1-216-009-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
22
82K
1.8K
3.3K
22
5%
0.50%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R315
R316
R317
R318
R319
1-216-676-11
1-216-697-91
1-216-651-11
1-216-033-00
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
11K
82K
1K
220
2.2K
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R320
R321
R322
R324
R327
1-216-057-00
1-216-009-00
1-216-067-00
1-216-049-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
22
5.6K
1K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R328
R329
R330
R331
R332
1-216-073-00
1-216-687-11
1-216-687-11
1-216-695-11
1-216-667-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
33K
33K
68K
4.7K
5%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R333
R334
R335
R336
R337
1-216-658-11
1-216-687-11
1-216-695-11
1-216-687-11
1-216-675-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2K
33K
68K
33K
10K
0.50%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R338
R340
R342
R343
R344
1-216-650-11
1-216-651-11
1-216-057-00
1-216-025-91
1-216-057-00
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
910
1K
2.2K
100
2.2K
0.50%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R345
R346
R349
R350
R351
1-216-049-91
1-216-675-11
1-216-053-00
1-216-638-11
1-216-674-11
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
1K
10K
1.5K
300
9.1K
5%
0.50%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R352
R353
R354
R357
R358
1-216-647-11
1-216-047-91
1-216-647-11
1-216-057-00
1-218-764-11
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
680
820
680
2.2K
330K
0.50%
5%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R359
R360
R361
R362
R363
1-216-025-91
1-218-758-11
1-216-675-11
1-216-121-91
1-216-671-11
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
100
180K
10K
1M
6.8K
5%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R365
R366
R367
R368
R369
1-216-047-91
1-216-651-11
1-216-676-11
1-216-691-11
1-216-051-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
820
1K
11K
47K
1.2K
5%
0.50%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R370
R372
1-216-025-91 RES,CHIP
1-216-049-91 RES,CHIP
100
1K
5%
5%
1/10W
1/10W
9-14
DESCRIPTION
REMARK
REF NO.
PART NO.
DESCRIPTION
REMARK
R373
R374
R375
1-216-073-00 RES,CHIP
1-216-633-11 METAL CHIP
1-216-627-11 METAL CHIP
10K
180
100
5%
1/10W
0.50% 1/10W
0.50% 1/10W
R376
R377
R378
R379
R380
1-216-057-00
1-216-057-00
1-216-049-91
1-216-053-00
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
2.2K
1K
1.5K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R381
R383
R384
R385
R386
1-216-025-91
1-216-065-91
1-216-073-00
1-216-658-11
1-216-683-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
100
4.7K
10K
2K
22K
5%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R387
R388
R389
R390
R391
1-216-687-11
1-216-662-11
1-216-025-91
1-216-657-11
1-216-653-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
33K
3K
100
1.8K
1.2K
0.50%
0.50%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R392
R393
R394
R395
R396
1-216-067-00
1-216-025-91
1-216-051-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
5.6K
100
1.2K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R397
R398
R399
R400
R401
1-216-679-11
1-216-049-91
1-216-025-91
1-216-073-00
1-216-675-11
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
15K
1K
100
10K
10K
0.50%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R402
R403
R404
R405
R406
1-216-687-11
1-216-679-11
1-216-025-91
1-216-653-11
1-216-025-91
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
33K
15K
100
1.2K
100
0.50%
0.50%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R407
R408
R409
R411
R412
1-216-665-11
1-216-658-11
1-216-661-11
1-216-073-00
1-216-677-11
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
3.9K
2K
2.7K
10K
12K
0.50%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R413
R414
R415
R416
R417
1-216-666-11
1-216-670-11
1-216-025-91
1-216-679-11
1-216-649-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
4.3K
6.2K
100
15K
820
0.50%
0.50%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R418
R420
R421
R422
R423
1-216-647-11
1-216-647-11
1-216-025-91
1-216-025-91
1-216-667-11
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
680
680
100
100
4.7K
0.50%
0.50%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R424
R425
R426
R427
R429
1-216-659-11
1-216-658-11
1-216-675-11
1-216-073-00
1-216-033-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
2.2K
2K
10K
10K
220
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R431
R432
R433
R434
R435
1-216-655-11
1-216-025-91
1-216-653-11
1-216-675-11
1-216-659-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
100
1.2K
10K
2.2K
0.50%
5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
BK
REF NO.
PART NO.
DESCRIPTION
REMARK
R436
R437
R438
R439
R440
1-216-669-11
1-216-057-00
1-216-025-91
1-216-057-00
1-216-073-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
5.6K
2.2K
100
2.2K
10K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R442
R446
R447
R448
R449
1-216-073-00
1-216-095-00
1-216-667-11
1-216-073-00
1-216-671-11
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
10K
82K
4.7K
10K
6.8K
5%
5%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R450
R451
R452
R453
R454
1-216-669-11
1-216-651-11
1-216-073-00
1-216-672-11
1-218-766-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
5.6K
1K
10K
7.5K
390K
0.50%
0.50%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R455
R456
R457
R458
R459
1-216-033-00
1-216-669-11
1-216-669-11
1-214-903-31
1-216-669-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL
METAL CHIP
220
5.6K
5.6K
39K
5.6K
5%
0.50%
0.50%
1%
0.50%
1/10W
1/10W
1/10W
1/2W
1/10W
R460
R461
R462
R463
R464
1-216-033-00
1-216-695-11
1-216-689-11
1-216-093-00
1-216-055-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
220
68K
39K
68K
1.8K
5%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R465
R466
R467
R468
R469
1-216-073-00
1-216-073-00
1-219-743-11
1-216-699-11
1-216-073-00
RES,CHIP
RES,CHIP
CARBON
METAL CHIP
RES,CHIP
10K
10K
100
100K
10K
5%
5%
5%
0.50%
5%
1/10W
1/10W
1/2W
1/10W
1/10W
R472
R473
R474
R480
R481
1-216-025-91
1-216-073-00
1-216-033-00
1-218-764-11
1-216-121-91
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
100
10K
220
330K
1M
5%
5%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R482
R483
R485
R486
R487
1-216-665-11
1-216-049-91
1-216-073-00
1-216-057-00
1-216-033-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
3.9K
1K
10K
2.2K
220
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R488
R500
R501
R502
R503
1-216-033-00
1-216-085-00
1-216-107-00
1-216-049-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
220
33K
270K
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R504
R505
R506
R507
R508
1-216-009-00
1-216-051-00
1-216-025-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22
1.2K
100
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R509
R510
R511
R512
R513
1-216-009-00
1-216-009-00
1-216-697-91
1-216-657-11
1-216-663-11
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
22
82K
1.8K
3.3K
5%
5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R514
R515
R516
R517
1-216-009-00
1-216-674-11
1-216-697-91
1-216-651-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
9.1K
82K
1K
5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
REF NO.
PART NO.
DESCRIPTION
REMARK
R518
1-216-033-00 RES,CHIP
220
5%
1/10W
R519
R520
R521
R522
R524
1-216-057-00
1-216-057-00
1-216-009-00
1-216-067-00
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
2.2K
22
5.6K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R527
R528
R529
R530
R531
1-216-679-11
1-216-690-11
1-216-025-91
1-216-073-00
1-216-057-00
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
15K
43K
100
10K
2.2K
0.50%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R532
R540
R541
R542
R543
1-216-049-91
1-216-637-11
1-216-674-11
1-216-647-11
1-216-047-91
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
1K
270
9.1K
680
820
5%
0.50%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R544
R546
R547
R548
R549
1-216-647-11
1-216-053-00
1-216-057-00
1-218-764-11
1-216-025-91
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
680
1.5K
2.2K
330K
100
0.50%
5%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R550
R551
R552
R553
R555
1-218-758-11
1-216-675-11
1-216-121-91
1-216-671-11
1-216-047-91
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
180K
10K
1M
6.8K
820
0.50%
0.50%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R556
R557
R558
R559
R560
1-216-651-11
1-216-676-11
1-216-691-11
1-216-051-00
1-216-025-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
1K
11K
47K
1.2K
100
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R562
R563
R564
R565
R566
1-216-049-91
1-216-049-91
1-216-025-91
1-216-073-00
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
100
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R567
R568
R569
R570
R571
1-216-097-91
1-216-633-11
1-216-627-11
1-216-057-00
1-216-057-00
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
100K
180
100
2.2K
2.2K
5%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R572
R573
R574
R575
R576
1-216-049-91
1-216-053-00
1-216-049-91
1-216-025-91
1-216-057-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1.5K
1K
100
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R577
R578
R579
R580
R581
1-216-065-91
1-216-073-00
1-216-658-11
1-216-683-11
1-216-687-11
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
2K
22K
33K
5%
5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R582
R583
R584
R585
R586
1-216-662-11
1-216-025-91
1-216-657-11
1-216-653-11
1-216-067-00
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
3K
100
1.8K
1.2K
5.6K
0.50%
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R587
R588
1-216-025-91 RES,CHIP
1-216-051-00 RES,CHIP
100
1.2K
5%
5%
1/10W
1/10W
9-15
BK
REF NO.
PART NO.
R589
R590
R591
1-216-073-00 RES,CHIP
1-216-073-00 RES,CHIP
1-216-679-11 METAL CHIP
10K
10K
15K
5%
1/10W
5%
1/10W
0.50% 1/10W
R592
R593
R594
R595
R596
1-216-049-91
1-216-025-91
1-216-073-00
1-216-675-11
1-216-687-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
1K
100
10K
10K
33K
5%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R597
R598
R599
R600
R601
1-216-679-11
1-216-025-91
1-216-653-11
1-216-025-91
1-216-665-11
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
15K
100
1.2K
100
3.9K
0.50%
5%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R602
R603
R605
R606
R607
1-216-658-11
1-216-661-11
1-216-073-00
1-216-677-11
1-216-666-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
2K
2.7K
10K
12K
4.3K
0.50%
0.50%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R608
R609
R610
R611
R612
1-216-670-11
1-216-025-91
1-216-679-11
1-216-649-11
1-216-647-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.2K
100
15K
820
680
0.50%
5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R614
R615
R616
R617
R618
1-216-647-11
1-216-025-91
1-216-025-91
1-216-667-11
1-216-659-11
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
680
100
100
4.7K
2.2K
0.50%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R619
R620
R621
R623
R625
1-216-658-11
1-216-675-11
1-216-073-00
1-216-033-00
1-216-655-11
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
2K
10K
10K
220
1.5K
0.50%
0.50%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R626
R627
R628
R629
R630
1-216-025-91
1-216-653-11
1-216-675-11
1-216-659-11
1-216-669-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1.2K
10K
2.2K
5.6K
5%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R631
R632
R633
R634
R636
1-216-057-00
1-216-025-91
1-216-057-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
100
2.2K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R640
R641
R642
R643
R644
1-216-095-00
1-216-065-91
1-216-073-00
1-216-671-11
1-216-669-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
82K
4.7K
10K
6.8K
5.6K
5%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R645
R646
R647
R648
R649
1-216-651-11
1-216-073-00
1-216-672-11
1-218-766-11
1-216-033-00
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
1K
10K
7.5K
390K
220
0.50%
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R650
R651
R652
R653
R654
1-216-669-11
1-216-669-11
1-214-903-31
1-216-669-11
1-216-033-00
METAL CHIP
METAL CHIP
METAL
METAL CHIP
RES,CHIP
5.6K
5.6K
39K
5.6K
220
0.50%
0.50%
1%
0.50%
5%
1/10W
1/10W
1/2W
1/10W
1/10W
9-16
DESCRIPTION
REMARK
REF NO.
PART NO.
DESCRIPTION
REMARK
R655
R656
R657
R658
R659
1-216-695-11
1-216-689-11
1-216-093-00
1-216-055-00
1-216-073-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
68K
39K
68K
1.8K
10K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R660
R661
R662
R663
R672
1-216-073-00
1-219-743-11
1-216-699-11
1-216-073-00
1-216-025-91
RES,CHIP
CARBON
METAL CHIP
RES,CHIP
RES,CHIP
10K
100
100K
10K
100
5%
5%
0.50%
5%
5%
1/10W
1/2W
1/10W
1/10W
1/10W
R673
R674
R680
R681
R682
1-216-073-00
1-216-033-00
1-218-764-11
1-216-121-91
1-216-665-11
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
10K
220
330K
1M
3.9K
5%
5%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R683
R685
R686
R687
R688
1-216-049-91
1-216-073-00
1-216-057-00
1-216-033-00
1-216-033-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
10K
2.2K
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R700
R701
R702
R703
R704
1-216-065-91
1-216-065-91
1-216-065-91
1-216-065-91
1-216-065-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
4.7K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R705
R706
R707
R708
R709
1-216-065-91
1-216-073-00
1-216-073-00
1-216-073-00
1-216-677-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
4.7K
10K
10K
10K
12K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R710
R711
R712
R713
R714
1-216-671-11
1-216-691-11
1-216-685-11
1-216-049-91
1-216-049-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
6.8K
47K
27K
1K
1K
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R715
R716
R717
R718
R719
1-216-067-00
1-216-049-91
1-216-097-91
1-216-675-11
1-216-663-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
5.6K
1K
100K
10K
3.3K
5%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R720
R721
R722
R723
R724
1-216-073-00
1-216-025-91
1-216-025-91
1-216-009-00
1-216-009-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
100
100
22
22
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R725
R726
R727
R728
R729
1-216-065-91
1-216-065-91
1-216-073-00
1-216-067-00
1-216-061-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
4.7K
10K
5.6K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R730
R731
R732
R733
R735
1-216-057-00
1-216-065-91
1-216-065-91
1-216-295-91
1-216-033-00
RES,CHIP
RES,CHIP
RES,CHIP
SHORT
RES,CHIP
2.2K
4.7K
4.7K
0
220
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R736
R741
R800
R801
1-216-033-00
1-216-073-00
1-216-025-91
1-216-063-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
220
10K
100
3.9K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
BK
REF NO.
PART NO.
DESCRIPTION
REMARK
R802
1-216-085-00 RES,CHIP
33K
5%
1/10W
R803
R804
R805
R806
R807
1-216-049-91
1-216-063-91
1-216-091-00
1-216-049-91
1-216-079-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
3.9K
56K
1K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R808
R809
R810
R811
R812
1-216-049-91
1-216-049-91
1-216-045-00
1-216-047-91
1-216-063-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
680
820
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R813
R814
R815
R816
R817
1-216-053-00
1-216-065-91
1-216-077-00
1-216-085-00
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1.5K
4.7K
15K
33K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R818
R819
R820
R821
R822
1-216-081-00
1-216-085-00
1-216-053-00
1-216-049-91
1-216-081-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22K
33K
1.5K
1K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R823
R824
R825
R826
R827
1-216-037-00
1-216-041-00
1-216-057-00
1-216-694-11
1-216-057-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
330
470
2.2K
62K
2.2K
5%
5%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R828
R829
R830
R831
R832
1-216-037-00
1-218-766-11
1-218-755-11
1-216-661-11
1-216-637-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
390K
130K
2.7K
270
5%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R833
R834
R835
R836
R837
1-216-637-11
1-216-659-11
1-216-069-00
1-216-051-00
1-216-081-00
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
270
2.2K
6.8K
1.2K
22K
0.50%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R838
R839
R840
R841
R842
1-216-067-00
1-216-676-11
1-216-079-00
1-216-097-91
1-216-695-11
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
5.6K
11K
18K
100K
68K
5%
0.50%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R843
R844
R845
R846
R847
1-216-057-00
1-216-059-00
1-216-697-91
1-216-679-11
1-216-073-00
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
2.2K
2.7K
82K
15K
10K
5%
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R848
R849
R850
R851
R852
1-216-095-00
1-216-037-00
1-216-699-11
1-216-085-00
1-216-094-00
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
82K
330
100K
33K
75K
5%
5%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R853
R854
R855
R856
R857
1-216-049-91
1-216-675-11
1-216-649-11
1-216-659-11
1-216-659-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
820
2.2K
2.2K
5%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R858
R859
1-216-699-11 METAL CHIP
1-216-065-91 RES,CHIP
100K
4.7K
0.50% 1/10W
5%
1/10W
REF NO.
PART NO.
DESCRIPTION
REMARK
R860
R861
R862
1-216-065-91 RES,CHIP
1-216-667-11 METAL CHIP
1-216-699-11 METAL CHIP
4.7K
4.7K
100K
5%
1/10W
0.50% 1/10W
0.50% 1/10W
R863
R864
R865
R866
R867
1-216-674-11
1-216-675-11
1-216-649-11
1-216-057-00
1-216-025-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
9.1K
10K
820
2.2K
100
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R868
R869
R870
R871
R872
1-216-049-91
1-216-059-00
1-216-667-11
1-216-089-91
1-216-073-00
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
1K
2.7K
4.7K
47K
10K
5%
5%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R873
R874
R875
R876
R877
1-216-089-91
1-216-073-00
1-216-067-00
1-216-061-00
1-216-659-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
47K
10K
5.6K
3.3K
2.2K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R878
R879
R880
R881
R900
1-216-057-00
1-216-025-91
1-216-097-91
1-216-057-00
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
100
100K
2.2K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R901
R902
R903
R904
R905
1-216-097-91
1-216-097-91
1-216-097-91
1-216-025-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R909
R910
1-216-025-91
1-216-097-91
1-216-121-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
100K
1M
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R911
R912
R913
R914
R915
1-216-097-91
1-216-687-11
1-216-673-11
1-216-065-91
1-216-097-91
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
100K
33K
8.2K
4.7K
100K
5%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R916
R917
R918
R919
R920
1-216-097-91
1-216-097-91
1-216-097-91
1-216-661-11
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
100K
100K
100K
2.7K
100K
5%
5%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R921
R922
R923
R924
R925
1-216-667-11
1-216-671-11
1-216-065-91
1-216-065-91
1-216-065-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
6.8K
4.7K
4.7K
4.7K
0.50%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R926
R927
R928
R929
R930
1-216-065-91
1-216-065-91
1-216-065-91
1-216-675-11
1-216-675-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
4.7K
10K
10K
5%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R931
R947
R948
R949
R950
1-216-097-91
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
9-17
BK C
REF NO.
PART NO.
DESCRIPTION
REMARK
R951
R952
R953
R955
R956
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R958
R959
R960
R962
R970
1-216-073-00
1-216-073-00
1-216-049-91
1-216-097-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
1K
100K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R980
R1001
R1002
R1003
R1004
1-216-065-91
1-216-685-11
1-216-627-11
1-216-685-11
1-216-627-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
27K
100
27K
100
5%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R1005
R1006
R1007
R1008
R1009
1-216-685-11
1-216-627-11
1-216-685-11
1-216-627-11
1-216-685-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
27K
100
27K
100
27K
0.50%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R1010
R1011
R1012
R1013
R1014
1-216-627-11
1-216-685-11
1-216-627-11
1-216-685-11
1-216-627-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
27K
100
27K
100
0.50%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R1015
R1016
R1017
R1018
R1019
1-216-685-11
1-216-627-11
1-216-685-11
1-216-627-11
1-216-685-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
27K
100
27K
100
27K
0.50%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R1020
R1021
R1022
R1023
R1024
1-216-627-11
1-216-685-11
1-216-627-11
1-216-685-11
1-216-627-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
27K
100
27K
100
0.50%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
REF NO.
PART NO.
1-694-371-11 TERMINAL BOARD ASSY, I/O
REMARK
* A-1331-724-A C MOUNT
****************
<CAPACITOR>
C504
C505
C506
C507
C508
1-162-114-00
1-162-114-00
1-162-114-00
1-107-888-11
1-107-888-11
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
0.0047MF
0.0047MF
0.0047MF
47MF
20%
47MF
20%
2KV
2KV
2KV
25V
25V
C601
C602
C701
C702
C703
1-104-653-11
1-164-232-11
1-164-232-11
1-107-960-11
1-107-943-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
220MF
0.01MF
0.01MF
4.7MF
10MF
20%
10%
10%
20%
20%
16V
50V
50V
160V
160V
C704
C705
1-107-364-11 MYLAR
1-107-888-11 ELECT
0.01MF
47MF
10%
20%
200V
25V
<CONNECTOR>
CN501
CN502
CN503
CN504
CN505
1-508-786-00
1-695-915-11
1-766-241-11
* 1-564-507-11
* 1-564-507-11
CN506
CN507
CN508
* 1-564-507-11 PLUG, CONNECTOR 4P
* 1-564-506-11 PLUG, CONNECTOR 3P
* 1-564-511-11 PLUG, CONNECTOR 8P
PIN, CONNECTOR (5MM PITCH) 2P
TAB (CONTACT)
PIN, CONNECTOR (PC BOARD) 3P
PLUG, CONNECTOR 4P
PLUG, CONNECTOR 4P
<DIODE>
D501
D601
D602
D603
D604
8-719-979-58
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
D701
8-719-158-55 DIODE RD15SB
DIODE EGP10D
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
<IC>
<TERMINAL BOARD>
TB1
DESCRIPTION
IC601
IC701
8-759-983-69 IC LM358PS
8-759-346-42 IC TDA6101Q/N3
<THERMISTOR>
<SOCKET>
TH300
1-807-796-11 THERMISTOR
J501
! 1-251-116-11 SOCKET, CRT
<CRYSTAL>
<CHIP CONDUCTOR>
X900
1-578-689-21 VIBRATOR
*************************************************************
JR501
JR502
JR503
JR504
JR505
1-216-295-91
1-216-295-91
1-216-295-91
1-216-295-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR506
JR507
JR508
1-216-295-91 SHORT
1-216-295-91 SHORT
1-216-295-91 SHORT
0
0
0
<COIL>
L501
L502
L503
9-18
1-408-595-31 INDUCTOR
1-408-595-31 INDUCTOR
1-408-595-31 INDUCTOR
2.2µH
2.2µH
2.2µH
C E
REF NO.
PART NO.
DESCRIPTION
REMARK
PART NO.
DESCRIPTION
REMARK
*************************************************************
<TRANSISTOR>
Q601
Q602
Q603
REF NO.
* A-1346-666-A E COMPL (14G1/14G5)
*********
8-729-020-07 TRANSISTOR 2SC4686A(LBSONY)
8-729-020-07 TRANSISTOR 2SC4686A(LBSONY)
8-729-020-07 TRANSISTOR 2SC4686A(LBSONY)
* A-1346-667-A E COMPL (20G1)
*********
<RESISTOR>
R501
R502
R503
R504
R505
1-219-745-11
1-219-745-11
1-219-745-11
1-219-746-11
1-219-746-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
470
470
1K
1K
5%
5%
5%
5%
5%
1/2W
1/2W
1/2W
1/2W
1/2W
* X-4033-108-1
* 3-648-057-00
* 4-050-794-01
* 4-050-814-01
* 4-053-101-01
HEAT SINK ASSY, DEF
NUT (ISO-4), U
INSULATOR
SHIELD, PWB
SPACER, DY CONNECTOR
R506
R507
R508
R509
R510
1-219-746-11
1-219-696-11
1-219-755-11
1-219-759-11
1-219-743-11
CARBON
METAL OXIDE
CARBON
CARBON
CARBON
1K
30M
10M
1M
100
5%
5%
5%
5%
5%
1/2W
1W
1/2W
1/2W
1/2W
* 4-381-905-01
4-381-907-01
4-382-854-01
7-322-065-19
7-682-566-04
SPRING (D)
INSULATOR (A)
SCREW (M3X8), P, SW (+)
RUBBER, SILICON RTV (KE490W)
SCREW +B 4X20
R511
R512
R513
R514
R515
1-219-743-11
1-219-743-11
1-219-744-11
1-219-744-11
1-219-744-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
220
220
220
5%
5%
5%
5%
5%
1/2W
1/2W
1/2W
1/2W
1/2W
R516
R601
R602
R603
R604
1-219-753-11
1-216-103-00
1-216-097-91
1-216-093-00
1-216-065-91
CARBON
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
220K
180K
100K
68K
4.7K
5%
5%
5%
5%
5%
1/2W
1/10W
1/10W
1/10W
1/10W
R605
R606
R607
R608
R609
1-216-097-91
1-216-073-00
1-208-612-11
1-208-612-11
1-216-073-00
RES,CHIP
RES,CHIP
METAL OXIDE
METAL OXIDE
RES,CHIP
100K
10K
10M
10M
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1W
1W
1/10W
R610
R611
R612
R613
R614
1-216-103-00
1-216-073-00
1-216-073-00
1-216-111-00
1-219-759-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
CARBON
180K
10K
10K
390K
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/2W
R615
R701
R702
R703
R704
1-216-081-00
1-216-655-11
1-216-679-11
1-216-679-11
1-216-677-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
1.5K
15K
15K
12K
5%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R705
R706
R707
R708
1-214-903-31
1-216-049-91
1-216-113-00
1-219-743-11
METAL
RES,CHIP
RES,CHIP
CARBON
39K
1K
470K
100
1%
5%
5%
5%
1/2W
1/10W
1/10W
1/2W
<VARIABLE RESISTOR>
RV501 !
1-223-410-11 RES, ADJ, METAL FILM 110M
7-682-647-09 SCREW +PS 3X6
<CAPACITOR>
C001
C004
C005
C006
C008
1-164-004-11
1-164-004-11
1-164-004-11
1-110-501-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.1MF
0.1MF
0.33MF
0.1MF
10%
10%
10%
10%
10%
25V
25V
25V
16V
25V
C009
C010
C011
C012
C013
1-164-004-11
1-164-004-11
1-164-004-11
1-164-004-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.1MF
0.1MF
0.1MF
0.1MF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C014
C015
C016
C017
C018
1-164-232-11
1-163-017-00
1-164-346-11
1-163-275-11
1-110-501-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.0047MF
1MF
0.001MF
0.33MF
10%
10%
5%
10%
50V
50V
16V
50V
16V
C019
C020
C021
C022
C023
1-164-004-11
1-163-275-11
1-164-695-11
1-107-901-11
1-163-275-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1MF
0.001MF
0.0022MF
0.47MF
0.001MF
10%
5%
5%
20%
5%
25V
50V
50V
50V
50V
C024
C031
C032
C033
C034
1-164-232-11
1-128-528-11
1-128-528-11
1-107-910-11
1-137-399-11
CERAMIC CHIP
ELECT
ELECT
ELECT
FILM
0.01MF
470MF
470MF
100MF
0.1MF
10%
20%
20%
20%
5%
50V
25V
25V
50V
100V
C036
C051
C052
C053
C054
1-164-232-11
1-164-004-11
1-163-251-11
1-102-030-00
1-129-765-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
FILM
0.01MF
0.1MF
100PF
330PF
0.047MF
10%
10%
5%
10%
5%
50V
25V
50V
500V
200V
1-162-116-00
1-162-134-11
1-136-081-00
1-162-116-00
1-123-024-21
CERAMIC
CERAMIC
FILM
CERAMIC
ELECT
680PF
470PF
0.012MF
680PF
33MF
10%
10%
3%
10%
160V
2KV
2KV
2KV
2KV
<SPARK GAP>
SG501
SG502
SG503
SG504
SG505
1-519-422-11
1-519-421-11
1-519-421-11
1-519-421-11
1-519-421-11
GAP, SPARK
GAP, DISCHARGE
GAP, DISCHARGE
GAP, DISCHARGE
GAP, DISCHARGE
SG506
SG507
SG508
1-519-421-11 GAP, DISCHARGE
1-519-421-11 GAP, DISCHARGE
1-519-422-11 GAP, SPARK
C055
C056
C057
C058
C061
C062
C063
C064
!
!
!
1-137-417-11 MYLAR
1-107-995-11 ELECT
1-109-921-11 CERAMIC
0.0047MF 10%
100MF
0
0.0015MF 10%
200V
160V
500V
9-19
E
REF NO.
PART NO.
DESCRIPTION
C065
1-104-496-11 FILM
3.3MF
3%
C065
1-109-915-11 FILM
2.2MF
3%
C066
1-104-494-11 FILM
3.9MF
3%
C066
C072
C073
C074
1-109-915-11
1-164-004-11
1-163-275-11
1-107-906-11
2.2MF
0.1MF
0.001MF
10MF
3%
10%
5%
20%
FILM
CERAMIC CHIP
CERAMIC CHIP
ELECT
REMARK
200V
(14G1/14G5)
200V (20G1)
25V
50V
50V
C075
C076
C077
C078
C079
1-107-906-11
1-164-695-11
1-164-346-11
1-163-251-11
1-107-888-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
10MF
0.0022MF
1MF
100PF
47MF
C080
C081
C082
C083
C086
1-107-888-11
1-164-232-11
1-164-346-11
1-164-346-11
1-106-375-12
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
MYLAR
47MF
20%
0.01MF 10%
1MF
1MF
0.022MF 99%
25V
50V
16V
16V
200V
C087
C091
C101
C102
C103
1-106-375-12
1-164-004-11
1-128-526-11
1-128-526-11
1-164-232-11
MYLAR
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.022MF
0.1MF
100MF
100MF
0.01MF
200V
25V
25V
25V
50V
C104
C105
C111
1-164-004-11 CERAMIC CHIP
1-164-346-11 CERAMIC CHIP
1-137-352-11 FILM
0.1MF
10%
1MF
0.033MF 5%
C111
C112
1-137-353-11 FILM
1-164-004-11 CERAMIC CHIP
0.047MF 5%
0.1MF
10%
25V
16V
100V
(14G1/14G5)
100V (20G1)
25V
C113
C121
C122
C123
C131
1-163-133-00
1-102-228-00
1-164-004-11
1-102-228-00
1-164-346-11
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
470PF
470PF
0.1MF
470PF
1MF
50V
500V
25V
500V
16V
C132
C141
C151
C156
C160
C161
1-164-505-11
1-164-004-11
1-164-004-11
1-104-987-11
1-164-346-11
1-163-275-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
FILM
CERAMIC CHIP
CERAMIC CHIP
2.2MF
0.1MF
0.1MF
0.001MF
1MF
0.001MF
C171
C172
C201
C202
C203
1-163-222-11
1-163-222-11
1-107-906-11
1-164-346-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
5PF
5PF
10MF
1MF
0.022MF
0.25PF 50V
0.25PF 50V
20% 50V
16V
10% 50V
C204
C205
C208
C210
C231
1-164-004-11
1-164-004-11
1-107-906-11
1-164-004-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.1MF
10MF
0.1MF
0.01MF
10%
10%
20%
10%
10%
25V
25V
50V
25V
50V
C232
C241
C242
C271
C272
1-164-004-11
1-163-251-11
1-164-004-11
1-163-121-00
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1MF
100PF
0.1MF
150PF
0.1MF
10%
5%
10%
5%
10%
25V
50V
25V
50V
25V
C273
C274
C275
1-163-275-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-163-275-11 CERAMIC CHIP
0.001MF 5%
0.1MF
10%
0.001MF 5%
50V
25V
50V
9-20
20%
5%
200V
(14G1/14G5)
200V (20G1)
5%
20%
99%
10%
20%
20%
10%
5%
10%
10%
10%
10%
10%
10%
5%
50V
50V
16V
50V
25V
16V
25V
25V
200V
16V
50V
REF NO.
PART NO.
DESCRIPTION
REMARK
C276
C277
1-164-004-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
0.1MF
0.1MF
10%
10%
C278
C301
C302
C303
C304
1-163-275-11
1-164-004-11
1-164-346-11
1-163-227-11
1-163-133-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001MF
0.1MF
1MF
10PF
470PF
5%
10%
C321
C331
C332
C333
C501
1-164-505-11
1-164-004-11
1-163-222-11
1-163-222-11
1-130-481-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
MYLAR
2.2MF
0.1MF
5PF
5PF
0.0068MF
10%
0.25PF
0.25PF
5%
16V
25V
50V
50V
50V
C502
C505
C506
C507
C509
1-163-275-11
1-164-004-11
1-163-275-11
1-164-004-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001MF
0.1MF
0.001MF
0.1MF
0.1MF
5%
10%
5%
10%
10%
50V
25V
50V
25V
25V
C510
C511
C512
C513
C514
1-163-259-91
1-107-906-11
1-107-907-11
1-164-695-11
1-164-346-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
220PF
10MF
22MF
0.0022MF
1MF
5%
20%
20%
5%
50V
50V
50V
50V
16V
C515
C516
C517
C519
C521
1-163-251-11
1-164-346-11
1-107-888-11
1-164-004-11
1-107-906-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
100PF
1MF
47MF
0.1MF
10MF
5%
50V
16V
25V
25V
50V
C531
C532
C533
C534
C541
1-106-343-00
1-107-888-11
1-164-346-11
1-164-232-11
1-107-906-11
MYLAR
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001MF
47MF
1MF
0.01MF
10MF
C542
C543
C544
C551
C552
1-107-888-11
1-164-346-11
1-164-232-11
1-107-995-11
1-137-417-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
MYLAR
47MF
1MF
0.01MF
100MF
0.0047MF
C553
C555
C556
C557
C558
1-106-355-12
1-164-004-11
1-162-134-11
1-136-081-00
1-162-114-00
MYLAR
CERAMIC CHIP
CERAMIC
FILM
CERAMIC
0.0033MF
0.1MF
470PF
0.012MF
0.0047MF
10%
10%
10%
3%
200V
25V
2KV
2KV
2KV
C559
C561
C562
C571
C572
1-136-111-00
1-104-652-11
1-107-492-11
1-163-275-11
1-164-004-11
FILM
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
1MF
470MF
47MF
0.001MF
0.1MF
5%
20%
20%
5%
10%
200V
10V
160V
50V
25V
C601
C602
1-113-503-11 CERAMIC CHIP
1-163-145-00 CERAMIC CHIP
0.0039MF 5%
0.0015MF 5%
C602
C611
C612
C613
1-164-695-11
1-164-004-11
1-164-004-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022MF
0.1MF
0.1MF
100PF
5%
10%
10%
5%
25V
50V
(14G1/14G5)
50V (20G1)
25V
25V
50V
C621
C622
C623
C624
C625
1-163-275-11
1-164-004-11
1-163-275-11
1-164-004-11
1-163-135-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001MF
0.1MF
0.001MF
0.1MF
560PF
5%
10%
5%
10%
5%
50V
25V
50V
25V
50V
25V
25V
50V
25V
16V
0.5PF 50V
5%
50V
20%
10%
20%
10%
20%
10%
20%
20%
10%
0
10%
200V
25V
16V
50V
50V
25V
16V
50V
160V
200V
E
REF NO.
PART NO.
DESCRIPTION
REMARK
C626
C631
C641
C642
C643
1-164-004-11
1-164-004-11
1-164-004-11
1-107-906-11
1-107-906-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1MF
0.1MF
0.1MF
10MF
10MF
10%
10%
10%
20%
20%
25V
25V
25V
50V
50V
C644
C701
C702
C711
C712
1-164-346-11
1-164-232-11
1-164-004-11
1-163-275-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1MF
0.01MF
0.1MF
0.001MF
0.1MF
10%
10%
5%
10%
16V
50V
25V
50V
25V
C721
C724
C725
C741
C742
1-163-259-91
1-104-987-11
1-163-251-11
1-163-222-11
1-163-222-11
CERAMIC CHIP
FILM
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.001MF
100PF
5PF
5PF
5%
10%
5%
0.25PF
0.25PF
50V
200V
50V
50V
50V
C801
C802
C811
C812
C813
1-107-889-11
1-107-889-11
1-164-005-11
1-164-005-11
1-164-005-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220MF
220MF
0.47MF
0.47MF
0.47MF
20%
20%
C814
C815
C816
C821
C862
1-164-005-11
1-164-005-11
1-164-005-11
1-107-906-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.47MF
0.47MF
0.47MF
10MF
100PF
C873
C911
C912
C913
C916
1-163-251-11
1-107-889-11
1-107-889-11
1-107-889-11
1-164-005-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
100PF
220MF
220MF
220MF
0.47MF
C917
C918
C919
C920
C921
1-164-005-11
1-164-005-11
1-164-005-11
1-164-005-11
1-128-528-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.47MF
0.47MF
0.47MF
0.47MF
470MF
C922
C923
C924
C925
C926
1-128-526-11
1-128-526-11
1-164-005-11
1-164-005-11
1-164-005-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
100MF
0.47MF
0.47MF
0.47MF
C928
C929
C930
C931
C932
1-164-005-11
1-164-005-11
1-164-005-11
1-107-889-11
1-107-889-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.47MF
0.47MF
0.47MF
220MF
220MF
C933
C936
C938
C939
C941
1-107-889-11
1-164-005-11
1-164-005-11
1-164-005-11
1-128-528-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
220MF
0.47MF
0.47MF
0.47MF
470MF
20%
C942
C943
C946
C947
C948
1-128-526-11
1-128-526-11
1-164-005-11
1-164-005-11
1-164-005-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
100MF
0.47MF
0.47MF
0.47MF
20%
20%
C949
C950
C951
C952
C956
1-164-005-11
1-164-005-11
1-104-652-11
1-104-652-11
1-164-005-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.47MF
0.47MF
470MF
470MF
0.47MF
20%
5%
REF NO.
PART NO.
DESCRIPTION
REMARK
C961
C962
C963
C964
C965
1-104-652-11
1-128-526-11
1-104-652-11
1-164-004-11
1-164-004-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
470MF
100MF
470MF
0.1MF
0.1MF
(20G1)
(20G1)
(20G1)
(20G1)
C966
C967
C968
C969
C970
1-164-005-11
1-164-005-11
1-164-005-11
1-164-005-11
1-164-005-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47MF
0.47MF
0.47MF
0.47MF
0.47MF
(20G1)
(20G1)
(20G1)
(20G1)
(20G1)
C971
C972
C976
C981
C986
1-104-652-11
1-104-652-11
1-164-005-11
1-104-652-11
1-164-005-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
470MF
470MF
0.47MF
470MF
0.47MF
10V
10V
25V
25V
25V
C987
C988
C992
C993
C994
1-164-005-11
1-164-005-11
1-128-526-11
1-128-526-11
1-128-526-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.47MF
0.47MF
100MF
100MF
100MF
25V
25V
25V
50V
50V
C996
C997
C998
C999
1-164-005-11
1-164-005-11
1-164-005-11
1-164-005-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47MF
0.47MF
0.47MF
0.47MF
20%
20%
20%
10%
10%
10V
16V
10V
25V
25V
25V
25V
25V
25V
25V
20%
20%
20%
20%
20%
20%
10V
10V
25V
10V
25V
25V
25V
16V
16V
16V
25V
25V
25V
25V
<CONNECTOR>
5%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
50V
25V
25V
25V
25V
25V
25V
25V
25V
16V
CN007
CN501
CN801
CN802
CN902
CN903
CN905
* 1-580-798-11
* 1-564-508-11
1-774-523-11
1-774-523-11
1-766-243-11
CONNECTOR PIN (DY) 6P
PLUG, CONNECTOR 5P
PIN, CONNECTOR (PC BOARD) 64P
PIN, CONNECTOR (PC BOARD) 64P
PIN, CONNECTOR (PC BOARD) 5P
1-766-241-11 PIN, CONNECTOR (PC BOARD) 3P
1-766-240-11 PIN, CONNECTOR (PC BOARD) 2P
<DIODE>
16V
16V
25V
25V
25V
D031
D061
D062
D101
D102
8-719-908-03
8-719-037-24
8-719-920-67
8-719-971-20
8-719-971-20
DIODE GP08D
DIODE RD12SB3-T1
DIODE ERC91-02
DIODE ERC38-06
DIODE ERC38-06
25V
25V
25V
25V
25V
D103
D111
D112
D113
D121
8-719-158-15
8-719-036-86
8-719-404-49
8-719-404-49
8-719-404-49
DIODE RD5.6SB
DIODE RD4.3SB3-T1
DIODE MA111
DIODE MA111
DIODE MA111
25V
25V
25V
25V
16V
D122
D131
D151
D152
D153
8-719-036-86
8-719-404-49
8-719-404-49
8-719-404-49
8-719-901-83
DIODE RD4.3SB3-T1
DIODE MA111
DIODE MA111
DIODE MA111
DIODE 1SS83
16V
16V
25V
25V
25V
D154
D201
D271
D301
D321
8-719-901-83
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE 1SS83
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
25V
25V
10V
10V
25V
D322
D501
D502
D531
8-719-404-49
8-719-037-24
8-719-404-49
8-719-404-49
DIODE MA111
DIODE RD12SB3-T1
DIODE MA111
DIODE MA111
9-21
E
REF NO.
PART NO.
D532
DESCRIPTION
REMARK
REF NO.
PART NO.
DESCRIPTION
REMARK
8-719-404-49 DIODE MA111
IC702
8-759-822-38 IC LA6510 (20G1)
D533
D534
D542
D543
D544
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
IC703
IC801
IC802
IC803
IC921
8-759-064-36
8-759-032-26
8-759-473-55
8-759-156-54
8-759-231-58
IC MB88346BPFV (20G1)
IC MC74HC125AF
IC MB89613R-438
IC X25040SI
IC TA7812S
D545
D551
D552
D553
D554
8-719-404-49
8-719-037-24
8-719-941-74
8-719-920-67
8-719-404-49
DIODE MA111
DIODE RD12SB3-T1
DIODE ERB91-02
DIODE ERC91-02
DIODE MA111
IC941
IC961
IC981
IC991
8-759-701-88
8-759-144-82
8-759-247-67
8-759-701-59
IC NJM7912FA
IC µPC2405HF
IC LM2990T-5.0
IC NJM78M09FA
D555
D611
D641
D642
D721
8-719-018-82
8-719-404-49
8-719-157-91
8-719-157-91
8-719-404-49
DIODE RGP02-20EL-6394
DIODE MA111
DIODE RD3.0SB
DIODE RD3.0SB
DIODE MA111 (20G1)
D722
D801
D802
D853
8-719-404-49
8-719-158-15
8-719-404-49
8-719-158-19
DIODE MA111 (20G1)
DIODE RD5.6SB
DIODE MA111
DIODE RD6.2SB
<COIL>
<FERRITE BEAD>
FB051
1-543-298-11 FERRITE
0µH
<FILTER>
FL801
FL901
1-407-365-00
1-412-537-31
1-411-594-11
1-412-541-21
1-416-581-11
COIL,CHOKE
INDUCTOR
100µH
INDUCTOR
0µH
INDUCTOR
220µH
COIL, HORIZONTAL LINEARITY (20G1)
L064
L066
L101
L551
L552
1-416-582-11
1-412-541-21
1-459-148-00
1-406-659-11
1-423-855-11
COIL, HORIZONTAL LINEARITY (14G1/14G5)
INDUCTOR
220µH
COIL
INDUCTOR
0µH
TRANSFORMER, FERRITE (HRT)
L553
L554
L951
1-406-669-11 INDUCTOR
1-407-365-00 COIL,CHOKE
1-412-541-21 INDUCTOR
IC001
IC031
IC071
IC091
IC101
8-752-068-39
8-759-192-71
8-759-443-10
8-759-100-96
8-759-803-42
IC CXA1840S
IC STV9379
IC FA5301BN-TE1
IC µPC4558G2
IC LA6500-FA
IC151
IC201
IC202
IC203
IC204
8-752-068-37
8-752-074-64
8-759-981-48
8-759-988-13
8-759-981-48
IC CXA1726AM
IC CXA2026AS
IC TL082M
IC LM393PS
IC TL082M
IC205
IC231
IC301
IC501
IC502
8-759-064-36
8-759-822-38
8-752-068-37
8-759-981-48
8-759-908-15
IC MB88346BPFV
IC LA6510
IC CXA1726AM
IC TL082M
IC TL431CLP
IC503
IC531
IC602
IC611
IC612
8-759-443-10
8-759-988-13
8-759-038-15
8-759-988-13
8-759-100-96
IC FA5301BN-TE1
IC LM393PS
IC MC74HC4538AF
IC LM393PS
IC µPC4558G2
IC613
IC621
IC622
IC623
IC625
8-759-186-57
8-759-981-48
8-759-988-13
8-759-038-15
8-759-011-65
IC TC74VHC175F
IC TL082M
IC LM393PS
IC MC74HC4538AF
IC MC74HC4053F
IC627
IC628
IC641
IC701
8-759-186-30
8-759-186-30
8-759-100-96
8-752-068-37
IC TC74VHC14F
IC TC74VHC14F
IC µPC4558G2
IC CXA1726AM (20G1)
!
0µH
220µH
<TRANSISTOR>
1-239-183-11 FILTER, EMI
1-236-164-11 ENCAPSULATED COMPONENT
<IC>
9-22
L051
L061
L062
L063
L064
Q051
Q053
Q054
Q061
Q071
8-729-120-28
8-729-119-80
8-729-016-32
8-729-015-28
8-729-019-85
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC2688-LK
TRANSISTOR 2SC4927-01
TRANSISTOR IRFI9630GS
TRANSISTOR 2SC3392-5-TB
Q072
Q091
Q111
Q112
Q121
8-729-824-26
8-729-800-32
8-729-216-22
8-729-216-22
1-801-806-11
TRANSISTOR 2SA1338-5-TA
TRANSISTOR 2SC2362K-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR DTC144EKA-T146
Q122
Q131
Q132
Q133
Q151
1-801-806-11
8-729-216-22
1-801-806-11
1-801-806-11
8-729-216-22
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SA1162-G
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SA1162-G
Q152
Q155
Q156
Q157
Q159
8-729-216-22
8-729-140-50
8-729-800-32
8-729-809-29
8-729-809-26
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC3209LK
TRANSISTOR 2SC2362K-G
TRANSISTOR 2SC4159-E
TRANSISTOR 2SA1606-E
Q201
Q271
Q272
Q273
Q301
8-729-216-22
8-729-120-28
8-729-216-22
8-729-216-22
8-729-216-22
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
Q302
Q303
Q304
Q306
Q307
8-729-216-22
8-729-120-28
8-729-120-28
8-729-019-01
8-729-024-95
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SD2394-EF
TRANSISTOR 2SB1565EF
Q321
8-729-020-07 TRANSISTOR 2SC4686A(LBSONY)
E
REF NO.
PART NO.
Q322
Q501
Q502
Q551
8-729-020-07
8-729-019-85
8-729-824-26
8-729-015-28
Q552
Q553
Q554
Q555
Q561
DESCRIPTION
REMARK
REF NO.
PART NO.
TRANSISTOR 2SC4686A(LBSONY)
TRANSISTOR 2SC3392-5-TB
TRANSISTOR 2SA1338-5-TA
TRANSISTOR IRFI9630GS
R034
R035
1-216-669-11 METAL CHIP
1-216-374-00 METAL OXIDE
5.6K
2.7
0.50% 1/10W
5%
2W
R035
1-216-377-11 METAL OXIDE
4.7
5%
8-729-031-37
8-729-019-85
8-729-824-26
8-729-044-21
8-729-019-57
TRANSISTOR 2SC3837KQ
TRANSISTOR 2SC3392-5-TB
TRANSISTOR 2SA1338-5-TA
TRANSISTOR 2SK2655-01R-F165
TRANSISTOR 2SA1208S-TP
R036
R037
1-216-061-00 RES,CHIP
1-249-383-11 CARBON
3.3K
1.5
5%
5%
F
(20G1)
2W
F
(14G1/14G5)
1/10W
1/4W
F
Q611
Q621
Q622
Q641
Q721
1-801-806-11
8-729-120-28
1-801-806-11
8-729-120-28
8-729-216-22
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC1623-L5L6
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC1623-L5L6
TRANSISTOR 2SA1162-G (20G1)
R038
R040
R050
R051
R052
1-216-432-00
1-216-113-00
1-216-049-91
1-216-041-00
1-216-073-00
METAL OXIDE
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
820
470K
1K
470
10K
5%
5%
5%
5%
5%
1W
1/10W
1/10W
1/10W
1/10W
R053
R054
1-249-423-11 CARBON
1-215-917-11 METAL OXIDE
3.3K
1K
5%
5%
1/4W
3W
Q722
Q725
Q726
Q727
Q729
8-729-216-22
8-729-195-82
8-729-800-32
8-729-019-01
8-729-024-95
TRANSISTOR 2SA1162-G (20G1)
TRANSISTOR 2SC2958-L (20G1)
TRANSISTOR 2SC2362K-G (20G1)
TRANSISTOR 2SD2394-EF (20G1)
TRANSISTOR 2SB1565EF (20G1)
R054
1-215-919-11 METAL OXIDE
2.2K
5%
R055
1-215-917-11 METAL OXIDE
1K
5%
R055
1-215-919-11 METAL OXIDE
2.2K
5%
Q801
Q802
Q803
Q804
Q807
1-801-806-11
8-729-027-38
8-729-027-38
1-801-806-11
1-801-806-11
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTA144EKA-T146
TRANSISTOR DTA144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
R061
R062
R063
R064
R065
1-249-377-11
1-249-397-11
1-216-081-00
1-215-880-00
1-212-889-00
CARBON
CARBON
RES,CHIP
METAL OXIDE
FUSIBLE
0.47
22
22K
10
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/10W
2W
1/4W
Q808
Q809
Q815
8-729-027-38 TRANSISTOR DTA144EKA-T146
8-729-027-38 TRANSISTOR DTA144EKA-T146
8-729-027-38 TRANSISTOR DTA144EKA-T146
R071
R072
R074
R074
1-216-669-11
1-216-675-11
1-216-662-11
1-216-663-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
5.6K
10K
3K
3.3K
0.50%
0.50%
0.50%
0.50%
R075
1-216-083-00 RES,CHIP
27K
5%
1/10W
1/10W
1/10W(20G1)
1/10W
(14G1/14G5)
1/10W
R076
R077
R078
R079
R080
1-216-073-00
1-216-073-00
1-216-083-00
1-216-069-00
1-216-685-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
10K
10K
27K
6.8K
27K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R081
R082
R083
R084
R086
1-216-049-91
1-216-073-00
1-249-413-11
1-216-113-00
1-216-675-11
RES,CHIP
RES,CHIP
CARBON
RES,CHIP
METAL CHIP
1K
10K
470
470K
10K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/4W
1/10W
1/10W
R087
R088
R089
R091
R095
1-216-675-11
1-216-675-11
1-216-675-11
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
10K
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R100
R101
R102
R103
R104
1-249-381-11
1-249-381-11
1-249-381-11
1-216-369-00
1-216-065-91
CARBON
CARBON
CARBON
METAL OXIDE
RES,CHIP
1
1
1
1
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
2W
1/10W
R105
R106
R107
R108
R109
1-216-053-00
1-216-081-00
1-216-081-00
1-249-393-11
1-216-057-00
RES,CHIP
RES,CHIP
RES,CHIP
CARBON
RES,CHIP
1.5K
22K
22K
10
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/10W
R111
R112
R113
1-216-049-91 RES,CHIP
1-216-065-91 RES,CHIP
1-216-049-91 RES,CHIP
1K
4.7K
1K
5%
5%
5%
1/10W
1/10W
1/10W
<RESISTOR>
R001
R002
R003
R004
R005
1-216-673-11
1-216-073-00
1-216-073-00
1-216-133-00
1-216-025-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
8.2K
10K
10K
3.3M
100
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R006
R007
R008
R009
R010
1-216-025-91
1-216-093-00
1-216-689-11
1-216-057-00
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
68K
39K
2.2K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R011
R012
R013
R014
R016
1-216-065-91
1-216-025-91
1-216-095-00
1-216-103-00
1-216-085-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
100
82K
180K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R017
R019
R020
R021
R022
1-216-059-00
1-216-041-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.7K
470
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R023
R024
R025
R026
R028
1-216-049-91
1-216-049-91
1-216-073-00
1-216-049-91
1-216-659-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
1K
1K
10K
1K
2.2K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R029
R030
R031
R032
R033
1-216-675-11
1-216-129-00
1-249-377-11
1-249-377-11
1-216-682-11
METAL CHIP
RES,CHIP
CARBON
CARBON
METAL CHIP
10K
2.2M
0.47
0.47
20K
0.50%
5%
5%
5%
0.50%
1/10W
1/10W
1/4W
1/4W
1/10W
F
F
DESCRIPTION
REMARK
F
F
F
(20G1)
3W
F
(14G1/14G5)
3W
F
(20G1)
3W
F
(14G1/14G5)
F
F
F
F
F
F
F
F
F
F
9-23
E
REF NO.
PART NO.
R114
R115
1-216-089-91 RES,CHIP
1-216-065-91 RES,CHIP
47K
4.7K
5%
5%
1/10W
1/10W
R116
R117
R122
R126
R127
1-216-089-91
1-216-113-00
1-216-107-00
1-216-107-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
470K
270K
270K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R131
R132
R133
R134
R142
1-216-049-91
1-216-089-91
1-216-073-00
1-216-107-00
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
47K
10K
270K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R151
R152
R153
R154
R155
1-216-025-91
1-216-073-00
1-216-043-91
1-216-069-00
1-216-001-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
10K
560
6.8K
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R156
R157
R158
R159
R160
1-215-869-11
1-249-377-11
1-249-377-11
1-217-371-00
1-215-871-11
METAL OXIDE
CARBON
CARBON
FUSIBLE
METAL OXIDE
1K
0.47
0.47
0.47
2.2K
5%
5%
5%
10%
5%
1W
1/4W
1/4W
1/4W
1W
F
F
F
R161
R162
R163
R171
R172
1-216-353-00
1-215-863-11
1-249-377-11
1-216-073-00
1-216-073-00
METAL OXIDE
METAL OXIDE
CARBON
RES,CHIP
RES,CHIP
2.2
100
0.47
10K
10K
5%
5%
5%
5%
5%
1W
1W
1/4W
1/10W
1/10W
F
F
F
R173
R174
R175
R176
R177
1-216-081-00
1-216-089-91
1-216-083-00
1-216-073-00
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22K
47K
27K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R178
R179
R190
R191
R201
1-216-073-00
1-216-097-91
1-216-113-00
1-216-073-00
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
100K
470K
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R202
R203
R204
R205
R206
1-216-025-91
1-216-073-00
1-216-057-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
10K
2.2K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R207
R208
R209
R210
R211
1-216-693-11
1-216-073-00
1-216-073-00
1-216-109-00
1-216-025-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
56K
10K
10K
330K
100
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R221
R222
R223
R224
R225
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R226
R227
R228
R229
R230
1-216-073-00
1-216-073-00
1-216-073-00
1-216-097-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R231
1-216-073-00 RES,CHIP
10K
5%
1/10W
9-24
DESCRIPTION
REMARK
F
REF NO.
PART NO.
DESCRIPTION
REMARK
R232
R233
R234
R235
1-216-089-91
1-216-079-00
1-216-063-91
1-216-298-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
18K
3.9K
2.2
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R236
R237
R238
R239
R241
1-216-001-00
1-249-377-11
1-249-425-11
1-249-392-11
1-216-073-00
RES,CHIP
CARBON
CARBON
CARBON
RES,CHIP
10
0.47
4.7K
8.2
10K
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
1/4W
1/10W
R242
R243
R244
R245
R246
1-216-692-11
1-216-079-00
1-216-081-00
1-216-298-00
1-216-001-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
51K
18K
22K
2.2
10
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R247
R248
R249
R271
R272
1-249-377-11
1-249-421-11
1-249-405-11
1-216-049-91
1-216-073-00
CARBON
CARBON
CARBON
RES,CHIP
RES,CHIP
0.47
2.2K
100
1K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/10W
1/10W
R273
R274
R275
R276
R277
1-216-073-00
1-216-073-00
1-216-097-91
1-216-103-00
1-216-069-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
100K
180K
6.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R278
R279
R280
R281
R282
1-216-121-91
1-216-073-00
1-216-089-91
1-216-057-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1M
10K
47K
2.2K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R283
R284
R285
R286
R301
1-216-073-00
1-216-073-00
1-216-121-91
1-216-025-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
1M
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R302
R303
R304
R305
R306
1-216-073-00
1-216-069-00
1-216-051-00
1-216-053-00
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
6.8K
1.2K
1.5K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R307
R308
R309
R310
R311
1-208-610-11
1-216-035-00
1-216-069-00
1-249-377-11
1-249-377-11
METAL OXIDE
RES,CHIP
RES,CHIP
CARBON
CARBON
2M
270
6.8K
0.47
0.47
5%
5%
5%
5%
5%
1W
1/10W
1/10W
1/4W
1/4W
R312
R313
R321
R322
R323
1-249-401-11
1-216-025-91
1-216-085-00
1-208-610-11
1-208-612-11
CARBON
RES,CHIP
RES,CHIP
METAL OXIDE
METAL OXIDE
47
100
33K
2M
10M
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1W
1W
R324
R331
R332
R333
R334
1-202-830-00
1-216-073-00
1-216-089-91
1-216-073-00
1-216-073-00
SOLID
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
47K
10K
10K
20%
5%
5%
5%
5%
1/2W
1/10W
1/10W
1/10W
1/10W
R335
R336
R337
R338
R339
1-216-085-00
1-216-085-00
1-216-073-00
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
33K
33K
10K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
F
F
F
F
F
F
F
F
F
E
REF NO.
PART NO.
DESCRIPTION
REMARK
REF NO.
PART NO.
R340
R341
R342
R343
R344
1-216-073-00
1-216-097-91
1-216-089-91
1-216-089-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
100K
47K
47K
10K
5%
5%
5%
5%
5%
R345
R346
R347
R501
R502
1-216-085-00
1-216-089-91
1-216-089-91
1-216-097-91
1-216-681-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
33K
47K
47K
100K
18K
5%
5%
5%
5%
0.50%
R503
R504
1-216-683-11 METAL CHIP
1-216-643-11 METAL CHIP
22K
470
R504
R505
R505
1-216-655-11 METAL CHIP
1-216-681-11 METAL CHIP
1-216-683-11 METAL CHIP
1.5K
18K
22K
R508
R511
R512
R513
R514
1-216-073-00
1-216-667-11
1-216-093-00
1-216-073-00
1-216-097-91
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
4.7K
68K
10K
100K
5%
0.50%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R515
R516
R517
R518
R519
1-216-073-00
1-216-083-00
1-216-069-00
1-216-685-11
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
10K
27K
6.8K
27K
10K
5%
5%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R520
R521
R522
R523
R531
1-216-073-00
1-249-413-11
1-249-414-11
1-216-081-00
1-218-754-11
RES,CHIP
CARBON
CARBON
RES,CHIP
METAL CHIP
10K
470
560
22K
120K
5%
5%
5%
5%
0.50%
1/10W
1/4W
1/4W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
R561
R562
R563
R571
R572
1-216-073-00
1-216-105-91
1-216-073-00
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
220K
10K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
R601
R602
R604
R605
R611
1-216-107-00
1-216-081-00
1-216-075-00
1-216-065-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
270K
22K
12K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W(20G1)
0.50% 1/10W
0.50% 1/10W
(14G1/14G5)
0.50% 1/10W(20G1)
0.50% 1/10W(20G1)
0.50% 1/10W
(14G1/14G5)
R611
1-216-679-11 METAL CHIP
15K
R612
R612
1-216-073-00 RES,CHIP
1-216-677-11 METAL CHIP
10K
12K
R613
1-216-073-00 RES,CHIP
10K
0.50% 1/10W
(14G1/14G5)
5%
1/10W(20G1)
0.5% 1/10W
(14G1/14G5)
5%
1/10W
R614
R614
1-216-073-00 RES,CHIP
1-216-677-11 METAL CHIP
10K
12K
5%
0.5%
R615
R615
1-216-073-00 RES,CHIP
1-216-679-11 METAL CHIP
10K
15K
R616
1-216-079-00 RES,CHIP
18K
1/10W(20G1)
1/10W
(14G1/14G5)
5%
1/10W(20G1)
0.50% 1/10W
(14G1/14G5)
5%
1/10W
R617
R618
R619
R621
R622
1-216-083-00
1-216-073-00
1-216-073-00
1-216-097-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
27K
10K
10K
100K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R625
R626
R627
R628
R629
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R532
R533
R534
R535
R536
1-216-683-11
1-216-685-11
1-216-697-91
1-216-073-00
1-216-081-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
22K
27K
82K
10K
22K
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R630
R631
R632
R633
R634
1-216-097-91
1-216-075-00
1-216-065-91
1-216-073-00
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
12K
4.7K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R542
1-218-773-11 METAL CHIP
750K
R542
R543
R544
1-218-774-11 METAL CHIP
1-216-685-11 METAL CHIP
1-216-684-91 METAL CHIP
820K
27K
24K
R544
1-216-685-11 METAL CHIP
27K
0.50% 1/10W
(14G1/14G5)
0.50% 1/10W(20G1)
0.50% 1/10W
0.50% 1/10W
(14G1/14G5)
0.50% 1/10W(20G1)
R641
R642
R645
R646
R647
1-216-107-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
270K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R545
1-216-698-11 METAL CHIP
91K
R545
R546
R547
R548
1-216-699-11
1-216-073-00
1-216-081-00
1-216-097-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
10K
22K
100K
0.50% 1/10W
(14G1/14G5)
0.50% 1/10W(20G1)
5%
1/10W
5%
1/10W
5%
1/10W
R648
R649
R650
R651
R652
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R653
R701
R702
R703
R704
1-216-025-91
1-216-073-00
1-216-089-91
1-216-073-00
1-216-065-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
10K
47K
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
R551
R552
R553
R554
R555
1-249-377-11
1-216-081-00
1-249-397-11
1-212-881-11
1-216-065-91
CARBON
RES,CHIP
CARBON
FUSIBLE
RES,CHIP
0.47
22K
22
100
4.7K
5%
5%
5%
5%
5%
1/4W
1/10W
1/4W
1/4W
1/10W
R705
R706
R707
1-216-298-00 RES,CHIP
1-216-001-00 RES,CHIP
1-249-377-11 CARBON
2.2
10
0.47
5%
5%
5%
R708
1-249-425-11 CARBON
4.7K
5%
1/10W(20G1)
1/10W(20G1)
1/4W
F
(20G1)
1/4W
F
(20G1)
R556
R557
R558
R559
R560
1-216-065-91
1-216-065-91
1-216-073-00
1-216-001-00
1-212-998-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
FUSIBLE
4.7K
4.7K
10K
10
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/2W
F
F
F
F
F
DESCRIPTION
REMARK
F
9-25
E
REF NO.
PART NO.
DESCRIPTION
R709
1-249-393-11 CARBON
10
5%
1/4W
R711
R712
R713
R714
R715
1-216-073-00
1-216-692-11
1-216-079-00
1-216-089-91
1-216-298-00
10K
51K
18K
47K
2.2
5%
0.50%
5%
5%
5%
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
R716
R717
1-216-001-00 RES,CHIP
1-249-377-11 CARBON
10
0.47
5%
5%
R718
1-249-411-11 CARBON
330
5%
R719
1-249-395-11 CARBON
15
5%
R721
1-216-073-00 RES,CHIP
10K
5%
1/10W(20G1)
1/4W
F
(20G1)
1/4W
F
(20G1)
1/4W
F
(20G1)
1/10W(20G1)
R722
R724
R725
R726
R727
1-216-073-00
1-216-043-91
1-216-057-00
1-216-001-00
1-215-869-11
10K
560
2.2K
10
1K
5%
5%
5%
5%
5%
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1W
F
(20G1)
R728
1-249-377-11 CARBON
0.47
5%
1/4W
R729
1-249-377-11 CARBON
0.47
5%
1/4W
R731
1-249-377-11 CARBON
0.47
5%
1/4W
R732
1-215-877-11 METAL OXIDE
22K
5%
1W
R733
1-216-349-00 METAL OXIDE
1
5%
1W
R741
R742
R743
R744
R745
1-216-692-11
1-216-081-00
1-216-081-00
1-216-081-00
1-216-692-11
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
51K
22K
22K
22K
51K
0.50%
5%
5%
5%
0.50%
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
R746
R747
R748
R749
R750
1-216-081-00
1-216-097-91
1-216-692-11
1-216-097-91
1-216-692-11
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
22K
100K
51K
100K
51K
5%
5%
0.50%
5%
0.50%
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
R751
R752
R753
R754
R755
1-216-097-91
1-216-097-91
1-216-692-11
1-216-097-91
1-216-692-11
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
100K
100K
51K
100K
51K
5%
5%
0.50%
5%
0.50%
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
1/10W(20G1)
R756
R801
R802
R803
R804
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W(20G1)
1/10W
1/10W
1/10W
1/10W
R805
R806
R807
R808
R809
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
1-216-065-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
100
100
100
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R811
R812
R813
R814
1-216-097-91
1-216-097-91
1-216-097-91
1-216-065-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
4.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL OXIDE
REMARK
F
(20G1)
F
(20G1)
F
(20G1)
F
(20G1)
F
(20G1)
F
(20G1)
REF NO.
PART NO.
DESCRIPTION
REMARK
R815
1-216-065-91 RES,CHIP
4.7K
5%
1/10W
R816
R817
R818
R821
R823
1-216-097-91
1-216-097-91
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R824
R825
R851
R852
R853
1-216-049-91
1-216-073-00
1-216-025-91
1-216-025-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
10K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R854
R855
R856
R857
R858
1-216-025-91
1-216-097-91
1-216-041-00
1-216-097-91
1-216-041-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
100K
470
100K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R859
R860
R861
R862
R863
1-216-097-91
1-216-041-00
1-216-097-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
470
100K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R864
R865
R866
R867
R868
1-216-041-00
1-216-041-00
1-216-041-00
1-216-041-00
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
470
470
470
470
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R869
R870
R871
R872
R873
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
1-216-081-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
100
100
100
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R901
1-249-377-11 CARBON
0.47
5%
1/4W
<TRANSFORMER>
T051
T052
T151
T301
1-426-668-11
1-431-702-11
1-431-734-11
1-424-555-11
TRANSFORMER, FERRITE (HDT)
TRANSFORMER, FERRITE (HOT)
TRANSFORMER, FERRITE (HLT)
TRANSFORMER, FERRITE (DFT)
<TEST PIN>
TP031
TP052
TP151
TP551
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
PIN, POST
PIN, POST
PIN, POST
PIN, POST
<CRYSTAL>
X001
X801
1-760-895-21 VIBRATOR, CERAMIC
1-578-689-21 VIBRATOR
*************************************************************
9-26
F
G
REF NO.
PART NO.
DESCRIPTION
REMARK
* A-1316-334-A G COMPL
*********
X-4033-109-6
* X-4033-116-1
! 1-251-263-11
1-533-223-11
1-900-214-49
PANEL ASSY, POWER UNIT
FRAME ASSY, POWER
INLET, AC
HOLDER, FUSE (F1)
CONNECTOR ASSY, VH 7P
1-900-214-50
1-900-236-41
2-990-241-02
3-648-057-00
* 4-050-794-01
CONNECTOR ASSY, FASTON TAB (IC3P)
CONNECTOR ASSY,FLOATING FIT 4P
HOLDER (A), PLUG
NUT (ISO-4), U
INSULATOR
* 4-050-798-01
* 4-050-800-01
* 4-050-801-01
* 4-050-814-01
* 4-050-824-01
PLATE, NUT, AC INLET
PLETE (SMALL), NUT
PLETE (LARGE), NUT (D206-209,303,304)
SHIELD, PWB
INSULATOR, POWER UNIT
* 4-050-850-01
* 4-064-021-01
* 4-374-846-01
4-382-854-01
4-382-854-11
COVER, POWER UNIT
PLATE, NUT
COVER, CAPACITOR, CAP TYPE
SCREW (M3X8), P, SW (+)
SCREW (M3X10), P, SW (+)
7-682-566-04
7-682-647-09
7-682-649-09
7-682-654-09
7-682-661-01
SCREW +B 4X20
SCREW +PS 3X6
SCREW +PS 3X10
SCREW +PS 3X25
SCREW +PS 4X8
7-682-950-09 SCREW +PSW 3X12
7-685-872-09 SCREW +BVTT 3X8 (S)
<CAPACITOR>
C1
C2
C3
C4
C5
! 1-104-708-11 FILM
! 1-113-912-11 CERAMIC
! 1-113-912-11 CERAMIC
! 1-113-912-11 CERAMIC
! 1-113-912-11 CERAMIC
0.47MF
0.0047MF
0.0047MF
0.0047MF
0.0047MF
20%
20%
20%
20%
20%
250V
250V
250V
250V
250V
C6
C7
C8
C9
C10
! 1-104-708-11 FILM
! 1-113-924-11 CERAMIC
! 1-113-924-11 CERAMIC
! 1-113-924-11 CERAMIC
! 1-113-924-11 CERAMIC
0.47MF
0.0047MF
0.0047MF
0.0047MF
0.0047MF
20%
20%
20%
20%
20%
250V
250V
250V
250V
250V
C11
C12
C14
C15
C16
!
1-137-484-11
1-107-906-11
1-104-653-11
1-107-906-11
1-107-888-11
FILM
ELECT
ELECT
ELECT
ELECT
0.47MF
10MF
220MF
10MF
47MF
10%
20%
20%
20%
20%
630V
50V
16V
50V
25V
C17
C31
C32
C33
C34
1-107-906-11
1-163-009-11
1-163-251-11
1-163-009-11
1-136-921-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
FILM
10MF
0.001MF
100PF
0.001MF
1MF
20%
10%
5%
10%
5%
50V
50V
50V
50V
50V
C35
C36
C37
C38
C39
1-136-921-11
1-165-319-11
1-163-989-11
1-164-004-11
1-164-489-11
FILM
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1MF
0.1MF
0.033MF
0.1MF
0.22MF
5%
50V
50V
25V
25V
16V
C40
C41
1-104-539-11 FILM CHIP
1-163-031-11 CERAMIC CHIP
10%
10%
10%
0.001MF 5%
0.01MF
50V
50V
REF NO.
PART NO.
DESCRIPTION
REMARK
C42
C43
C44
1-107-910-11 ELECT
1-113-707-11 ELECT(BLOCK)
1-107-906-11 ELECT
100MF
220MF
10MF
20%
20%
20%
35V
450V
50V
C45
C46
C47
C101
C102
1-107-715-11
1-164-004-11
1-107-907-11
1-107-888-11
1-128-526-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
22MF
0.1MF
22MF
47MF
100MF
20%
10%
20%
20%
20%
25V
25V
50V
25V
16V
C103
C104
C105
C200
C201
1-107-906-11
1-107-888-11
1-163-031-11
1-164-004-11
1-164-004-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10MF
47MF
0.01MF
0.1MF
0.1MF
20%
20%
10%
10%
50V
25V
50V
25V
25V
C203
C204
C205
C206
C207
1-104-539-11
1-107-907-11
1-164-004-11
1-107-888-11
1-136-161-00
FILM CHIP
ELECT
CERAMIC CHIP
ELECT
FILM
0.001MF
22MF
0.1MF
47MF
0.047MF
5%
20%
10%
20%
5%
50V
50V
25V
25V
50V
C208
C211
C212
C213
C214
1-129-718-00
1-107-913-11
1-102-038-00
1-102-038-00
1-107-880-11
FILM
ELECT
CERAMIC
CERAMIC
ELECT
0.022MF
470MF
0.001MF
0.001MF
4700MF
5%
20%
500V
500V
20%
630V
50V
C215
C216
C217
C218
C219
1-107-880-11
1-163-037-11
1-164-004-11
1-102-038-00
1-102-038-00
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
CERAMIC
4700MF
0.022MF
0.1MF
0.001MF
0.001MF
20%
10%
10%
500V
500V
10V
50V
25V
C220
C221
C222
C223
C224
1-107-890-11
1-107-890-11
1-107-880-11
1-107-880-11
1-102-038-00
ELECT
ELECT
ELECT
ELECT
CERAMIC
2200MF
2200MF
4700MF
4700MF
0.001MF
20%
20%
20%
20%
500V
25V
25V
10V
10V
C225
C226
C227
C228
C229
1-102-038-00
1-107-880-11
1-107-880-11
1-107-890-11
1-107-890-11
CERAMIC
ELECT
ELECT
ELECT
ELECT
0.001MF
4700MF
4700MF
2200MF
2200MF
500V
20%
20%
20%
20%
10V
10V
25V
25V
C301
C302
C303
C304
C305
1-164-004-11
1-164-004-11
1-104-539-11
1-107-907-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
FILM CHIP
ELECT
CERAMIC CHIP
0.1MF
0.1MF
0.001MF
22MF
0.1MF
10%
10%
5%
20%
10%
25V
25V
50V
50V
25V
C306
C307
C308
C311
C312
1-107-888-11
1-107-909-11
1-129-718-00
1-102-038-00
1-102-038-00
ELECT
ELECT
FILM
CERAMIC
CERAMIC
47MF
47MF
0.022MF
0.001MF
0.001MF
20%
20%
5%
500V
500V
25V
10V
630V
C313
C314
C315
C316
C317
1-107-877-11
1-107-877-11
1-162-116-00
1-162-116-00
1-107-947-11
ELECT
ELECT
CERAMIC
CERAMIC
ELECT
1000MF
1000MF
680PF
680PF
220MF
20%
20%
10%
10%
20%
10V
10V
2KV
2KV
160V
C318
C319
C320
C321
C324
1-107-947-11
1-136-169-00
1-107-372-11
1-107-909-11
1-163-031-11
ELECT
FILM
FILM
ELECT
CERAMIC CHIP
220MF
0.22MF
0.22MF
47MF
0.01MF
20%
5%
10%
20%
160V
50V
200V
10V
50V
10V
9-27
G
REF NO.
PART NO.
C325
C802
C804
C805
C806
1-163-031-11
1-164-005-11
1-107-888-11
1-107-906-11
1-107-888-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.01MF
0.47MF
47MF
10MF
47MF
C807
C809
C810
C901
C902
1-107-906-11
1-107-906-11
1-107-906-11
1-113-912-11
1-113-912-11
ELECT
ELECT
ELECT
CERAMIC
CERAMIC
!
!
C903
C904
DESCRIPTION
1-107-888-11 ELECT
1-128-526-11 ELECT
REMARK
REF NO.
PART NO.
20%
20%
20%
50V
16V
25V
50V
25V
D804
D806
D807
D810
D811
8-719-404-49
8-719-404-49
8-719-404-49
8-719-106-23
8-719-159-13
10MF
10MF
10MF
0.0047MF
0.0047MF
20%
20%
20%
20%
20%
50V
50V
50V
250V
250V
D812
D901
8-719-159-13 DIODE RD5.1SB3-T2
8-719-911-19 DIODE 1SS119-25
47MF
100MF
20%
20%
25V
16V
!
1-564-321-00 PIN, CONNECTOR 2P
1-568-106-11 PIN, CONNECTOR 4P
1-774-523-11 PIN, CONNECTOR (PC BOARD) 64P
<DIODE>
D1
D2
D3
D4
D5
!
8-719-510-53
8-719-110-52
8-719-110-61
8-719-053-43
8-719-510-02
DIODE D4SB60L
DIODE RD20ESB1
DIODE RD24ESB1
DIODE SLR-325VCT31
DIODE D1NS4
D6
D8
D9
D31
D32
8-719-510-02
8-719-404-49
8-719-510-02
8-719-510-02
8-719-106-23
DIODE D1NS4
DIODE MA111
DIODE D1NS4
DIODE D1NS4
DIODE RD7.5M-B2
D33
D34
D35
D36
D101
8-719-510-02
8-719-110-61
8-719-510-02
8-719-029-04
8-719-911-19
DIODE D1NS4
DIODE RD24ESB1
DIODE D1NS4
DIODE D5L60
DIODE 1SS119-25
D102
D103
D104
D105
D106
8-719-404-49
8-719-053-43
8-719-404-49
8-719-158-49
8-719-110-50
DIODE MA111
DIODE SLR-325VCT31
DIODE MA111
DIODE RD12SB2
DIODE RD18ESB3
D202
D203
D204
D205
D206
8-719-988-55
8-719-979-58
8-719-510-37
8-719-060-27
8-719-510-37
DIODE RGP15K-6179
DIODE EGP10D
DIODE D5LC20U
DIODE SLR-325MCT31
DIODE D5LC20U
D207
D208
D209
D210
D211
8-719-510-37
8-719-510-37
8-719-510-37
8-719-404-49
8-719-404-49
DIODE D5LC20U
DIODE D5LC20U
DIODE D5LC20U
DIODE MA111
DIODE MA111
D212
D300
D302
D303
D304
8-719-110-50
8-719-404-49
8-719-988-55
8-719-031-79
8-719-029-04
DIODE RD18ESB3
DIODE MA111
DIODE RGP15K-6179
DIODE D5SC4M
DIODE D5L60
D305
D306
D307
D801
D803
8-719-404-49
8-719-404-49
8-719-110-50
8-719-060-27
8-719-404-49
DIODE MA111
DIODE MA111
DIODE RD18ESB3
DIODE SLR-325MCT31
DIODE MA111
REMARK
DIODE MA111
DIODE MA111
DIODE MA111
DIODE RD7.5M-B2
DIODE RD5.1SB3-T2
<FUSE>
F1
F201
F202
! 1-576-231-11 FUSE (H.B.C.) 4A/250V
! 1-533-987-11 FUSE, MICRO 5A/125V
! 1-533-987-11 FUSE, MICRO 5A/125V
<FERRITE BEAD>
<CONNECTOR>
CN1
CN2
CN3
DESCRIPTION
FB31
FB32
FB33
FB34
FB201
1-410-396-41
1-410-396-41
1-410-396-41
1-410-396-41
1-410-396-41
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0µH
0µH
0µH
0µH
0µH
FB301
1-410-396-41 FERRITE
0µH
<IC>
IC1
IC31
IC32
IC101
IC201
8-759-982-15
8-759-354-43
8-759-100-96
8-759-988-13
8-759-914-04
IC RC7815FA
IC TK83854D
IC µPC4558G2
IC LM393PS
IC TL494CNS
IC202
IC203
IC301
IC302
IC801
8-759-908-15
8-759-908-15
8-759-914-04
8-759-908-15
8-759-085-67
IC TL431CLP
IC TL431CLP
IC TL494CNS
IC TL431CLP
IC LM339NS
IC802
IC803
IC804
IC901
8-759-908-15
8-759-424-24
8-759-908-15
8-759-231-58
IC TL431CLP
IC MC74HC147FEL
IC TL431CLP
IC TA7812S
<COIL>
L201
L301
L302
1-406-661-11 INDUCTOR
1-406-661-11 INDUCTOR
1-406-661-11 INDUCTOR
0µH
0µH
0µH
<PHOTO COUPLER>
PH201
PH301
PH802
PH803
PH901
! 8-749-010-64 PHOTO COUPLER PC123F2
! 8-749-010-64 PHOTO COUPLER PC123F2
! 8-749-010-64 PHOTO COUPLER PC123F2
! 8-749-010-64 PHOTO COUPLER PC123F2
! 8-749-010-64 PHOTO COUPLER PC123F2
<TRANSISTOR>
9-28
Q1
Q2
Q4
Q5
Q6
8-729-043-95
8-729-043-95
8-729-043-95
8-729-118-44
8-729-027-87
TRANSISTOR 2SC3840(3)
TRANSISTOR 2SC3840(3)
TRANSISTOR 2SC3840(3)
TRANSISTOR 2SA1413-K
TRANSISTOR 2SB1261-K
Q7
Q8
Q9
Q31
Q32
1-801-806-11
8-729-118-44
1-801-806-11
8-729-044-22
8-729-120-28
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SA1413-K
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SK2209-01R-F165
TRANSISTOR 2SC1623-L5L6
G
REF NO.
PART NO.
DESCRIPTION
REMARK
Q101
Q102
Q103
Q104
Q105
8-729-119-78
8-729-027-38
1-801-806-11
1-801-806-11
8-729-120-28
TRANSISTOR 2SC2785-HFE
TRANSISTOR DTA144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC1623-L5L6
Q106
Q107
Q108
Q109
Q110
8-729-216-22
1-801-806-11
8-729-027-38
8-729-120-28
1-801-806-11
TRANSISTOR 2SA1162-G
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTA144EKA-T146
TRANSISTOR 2SC1623-L5L6
TRANSISTOR DTC144EKA-T146
Q203
Q204
Q205
Q206
Q207
8-729-019-85
8-729-824-26
8-729-044-62
1-801-806-11
8-729-820-73
TRANSISTOR 2SC3392-5-TB
TRANSISTOR 2SA1338-5-TA
TRANSISTOR 2SK2766-01R-F165
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC3746
Q208
Q209
Q210
Q211
Q212
8-729-112-61
8-729-900-53
8-729-112-61
1-801-806-11
8-729-820-73
TRANSISTOR 2SA1441-L
TRANSISTOR DTC114EK
TRANSISTOR 2SA1441-L
TRANSISTOR DTC144EKA-T146
TRANSISTOR 2SC3746
Q213
Q214
Q215
Q300
Q301
8-729-027-38
8-729-820-73
8-729-027-38
8-729-027-38
8-729-120-28
TRANSISTOR DTA144EKA-T146
TRANSISTOR 2SC3746
TRANSISTOR DTA144EKA-T146
TRANSISTOR DTA144EKA-T146
TRANSISTOR 2SC1623-L5L6
Q303
Q304
Q305
Q306
Q801
8-729-019-85
8-729-824-26
8-729-044-62
1-801-806-11
8-729-027-38
TRANSISTOR 2SC3392-5-TB
TRANSISTOR 2SA1338-5-TA
TRANSISTOR 2SK2766-01R-F165
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTA144EKA-T146
Q802
Q805
Q806
Q807
Q808
1-801-806-11
1-801-806-11
1-801-806-11
8-729-027-38
1-801-806-11
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTA144EKA-T146
TRANSISTOR DTC144EKA-T146
Q809
Q810
Q811
Q812
Q813
1-801-806-11
8-729-027-38
1-801-806-11
1-801-806-11
1-801-806-11
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTA144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
Q814
Q815
Q816
Q817
Q901
8-729-027-31
1-801-806-11
1-801-806-11
8-729-027-38
8-729-119-78
TRANSISTOR DTA124EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTC144EKA-T146
TRANSISTOR DTA144EKA-T146
TRANSISTOR 2SC2785-HFE
Q902
Q903
Q904
1-801-806-11 TRANSISTOR DTC144EKA-T146
1-801-806-11 TRANSISTOR DTC144EKA-T146
1-801-806-11 TRANSISTOR DTC144EKA-T146
<RESISTOR>
R1
R2
R3
R4
R5
R6
R7
R8
R9
!
1-202-884-11
1-202-962-11
1-215-900-11
1-215-900-11
1-215-900-11
SOLID
CEMENTED
METAL OXIDE
METAL OXIDE
METAL OXIDE
820K
3.3
22K
22K
22K
20%
5%
5%
5%
5%
1/2W
10W
2W
2W
2W
1-247-891-00
1-247-891-00
1-247-891-00
1-216-073-00
CARBON
CARBON
CARBON
RES,CHIP
330K
330K
330K
10K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/10W
F
F
F
REF NO.
PART NO.
DESCRIPTION
REMARK
R10
1-216-073-00 RES,CHIP
10K
5%
1/10W
R11
R12
R13
R14
R15
1-247-883-00
1-247-883-00
1-247-883-00
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
150K
150K
150K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R16
R17
R18
R19
R20
1-249-437-11
1-216-073-00
1-216-073-00
1-260-332-51
1-260-332-51
CARBON
RES,CHIP
RES,CHIP
CARBON
CARBON
47K
10K
10K
2.2K
2.2K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/2W
1/2W
R21
R22
R23
R31
R33
1-249-441-11
1-249-441-11
1-249-437-11
1-219-728-11
1-216-653-11
CARBON
CARBON
CARBON
METAL
METAL CHIP
100K
100K
47K
0.22
1.2K
5%
5%
5%
10%
0.50%
1/4W
1/4W
1/4W
5W
1/10W
R34
R35
R36
R37
R38
1-216-672-11
1-216-081-00
1-216-665-11
1-216-665-11
1-216-109-00
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
7.5K
22K
3.9K
3.9K
330K
0.50%
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R39
R40
R41
R42
R43
1-216-109-00
1-216-109-00
1-216-105-91
1-216-109-00
1-216-109-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
330K
330K
220K
330K
330K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R44
R45
R46
R47
R48
1-216-109-00
1-216-097-91
1-216-081-00
1-216-081-00
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
330K
100K
22K
22K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R49
R50
R51
R52
R53
1-216-109-00
1-216-677-11
1-249-393-11
1-249-429-11
1-215-481-00
RES,CHIP
METAL CHIP
CARBON
CARBON
METAL
330K
12K
10
10K
330K
5%
0.50%
5%
5%
1%
1/10W
1/10W
1/4W
1/4W
1/4W
R54
R55
R56
R57
R58
1-215-481-00
1-215-481-00
1-216-679-11
1-216-661-11
1-215-477-00
METAL
METAL
METAL CHIP
METAL CHIP
METAL
330K
330K
15K
2.7K
220K
1%
1%
0.50%
0.50%
1%
1/4W
1/4W
1/10W
1/10W
1/4W
R59
R60
R61
R62
R63
1-215-477-00
1-215-477-00
1-216-677-11
1-216-673-11
1-216-645-11
METAL
METAL
METAL CHIP
METAL CHIP
METAL CHIP
220K
220K
12K
8.2K
560
1%
1%
0.50%
0.50%
0.50%
1/4W
1/4W
1/10W
1/10W
1/10W
R64
R65
R66
R67
R68
1-216-089-91
1-216-097-91
1-215-477-00
1-215-477-00
1-215-477-00
RES,CHIP
RES,CHIP
METAL
METAL
METAL
47K
100K
220K
220K
220K
5%
5%
1%
1%
1%
1/10W
1/10W
1/4W
1/4W
1/4W
R69
R70
R73
R74
R101
1-216-673-11
1-249-393-11
1-216-073-00
1-211-881-11
1-215-865-11
METAL CHIP
CARBON
RES,CHIP
FUSIBLE
METAL OXIDE
8.2K
10
10K
0.47
220
0.50%
5%
5%
10%
5%
1/10W
1/4W
1/10W
1/2W
1W
R102
R103
1-216-089-91 RES,CHIP
1-216-081-00 RES,CHIP
47K
22K
5%
5%
1/10W
1/10W
F
F
F
9-29
G
REF NO.
PART NO.
REF NO.
PART NO.
R104
R105
R106
1-216-081-00 RES,CHIP
1-216-055-00 RES,CHIP
1-216-097-91 RES,CHIP
22K
1.8K
100K
5%
5%
5%
1/10W
1/10W
1/10W
R255
R256
R257
1-216-073-00 RES,CHIP
1-249-411-11 CARBON
1-247-747-11 CARBON
10K
330
470
5%
5%
5%
1/10W
1/4W
1/2W
F
R107
R108
R109
R110
R111
1-216-073-00
1-216-073-00
1-216-081-00
1-216-065-91
1-216-675-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
10K
10K
22K
4.7K
10K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R258
R259
R260
R261
R262
1-216-073-00
1-249-415-11
1-249-415-11
1-215-891-11
1-216-073-00
RES,CHIP
CARBON
CARBON
METAL OXIDE
RES,CHIP
10K
680
680
680
10K
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
2W
1/10W
F
F
F
R112
R113
R114
R115
R200
1-216-675-11
1-216-081-00
1-216-049-91
1-216-049-91
1-216-073-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
22K
1K
1K
10K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R263
R264
R265
R266
R290
1-249-415-11
1-249-415-11
1-249-415-11
1-249-415-11
1-216-073-00
CARBON
CARBON
CARBON
CARBON
RES,CHIP
680
680
680
680
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/10W
R201
R202
R203
R204
R206
1-216-073-00
1-216-017-00
1-216-041-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
47
470
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R291
R301
R302
R303
R304
1-216-073-00
1-216-073-00
1-216-029-00
1-216-041-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
150
470
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R207
R208
R209
R210
R211
1-216-057-00
1-216-669-11
1-216-677-11
1-216-073-00
1-216-683-11
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
2.2K
5.6K
12K
10K
22K
5%
0.50%
0.50%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R306
R307
R308
R309
R310
1-216-073-00
1-216-057-00
1-216-669-11
1-216-677-11
1-216-073-00
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
10K
2.2K
5.6K
12K
10K
5%
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R212
R213
R214
R215
R216
1-216-033-00
1-216-073-00
1-216-033-00
1-216-073-00
1-249-393-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
CARBON
220
10K
220
10K
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W
F
R311
R312
R313
R314
R315
1-216-683-11
1-216-033-00
1-216-073-00
1-216-033-00
1-216-073-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22K
220
10K
220
10K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R217
R218
R219
R220
R221
1-249-429-11
1-249-441-11
1-249-417-11
1-219-728-11
1-215-904-11
CARBON
CARBON
CARBON
METAL
METAL OXIDE
10K
100K
1K
0.22
100K
5%
5%
5%
10%
5%
1/4W
1/4W
1/4W
5W
2W
1-249-393-11
1-249-429-11
1-249-441-11
1-249-417-11
1-219-728-11
CARBON
CARBON
CARBON
CARBON
METAL
10
10K
100K
1K
0.22
5%
5%
5%
5%
10%
1/4W
1/4W
1/4W
1/4W
5W
F
F
R316
R317
R318
R319
R320
R222
R223
R224
R228
R229
1-215-904-11
1-215-904-11
1-215-904-11
1-260-288-11
1-215-882-00
METAL OXIDE
METAL OXIDE
METAL OXIDE
CARBON
METAL OXIDE
100K
100K
100K
0.47
22
5%
5%
5%
5%
5%
2W
2W
2W
1/2W
2W
R321
R322
R323
R324
R328
1-215-904-11
1-215-904-11
1-215-904-11
1-215-904-11
1-215-882-00
METAL OXIDE
METAL OXIDE
METAL OXIDE
METAL OXIDE
METAL OXIDE
100K
100K
100K
100K
22
5%
5%
5%
5%
5%
2W
2W
2W
2W
2W
F
F
F
F
F
R230
R231
R232
R233
R234
1-216-057-00
1-216-001-00
1-216-061-00
1-216-025-91
1-216-659-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
2.2K
10
3.3K
100
2.2K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R329
R331
R332
R333
R334
1-260-288-11
1-216-736-11
1-215-901-00
1-216-073-00
1-249-405-11
CARBON
METAL
METAL OXIDE
RES,CHIP
CARBON
0.47
270
33K
10K
100
5%
1%
5%
5%
5%
1/2W
10W
2W
1/10W
1/4W
F
R235
R236
R237
R240
R246
1-216-025-91
1-216-677-11
1-215-886-11
1-215-886-11
1-247-791-91
RES,CHIP
METAL CHIP
METAL OXIDE
METAL OXIDE
CARBON
100
12K
100
100
22
5%
0.50%
5%
5%
5%
1/10W
1/10W
2W
2W
1/4W
R335
R336
R337
R338
R339
1-249-405-11
1-214-905-11
1-214-905-11
1-216-658-11
1-219-728-11
CARBON
METAL
METAL
METAL CHIP
METAL
100
47K
47K
2K
0.22
5%
1%
1%
0.50%
10%
1/4W
1/2W
1/2W
1/10W
5W
R247
R248
R249
R250
R251
1-247-791-91
1-216-659-11
1-216-659-11
1-215-891-11
1-216-073-00
CARBON
METAL CHIP
METAL CHIP
METAL OXIDE
RES,CHIP
22
2.2K
2.2K
680
10K
5%
0.50%
0.50%
5%
5%
1/4W
1/10W
1/10W
2W
1/10W
R340
R801
R802
R803
R804
1-216-651-11
1-216-049-91
1-216-057-00
1-216-065-91
1-216-053-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
2.2K
4.7K
1.5K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R252
R253
R254
1-249-413-11 CARBON
1-249-413-11 CARBON
1-247-747-11 CARBON
470
470
470
5%
5%
5%
1/4W
1/4W
1/2W
R805
R806
R807
R808
1-216-121-91
1-216-073-00
1-216-061-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1M
10K
3.3K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
9-30
DESCRIPTION
REMARK
F
F
F
F
F
F
F
F
F
DESCRIPTION
REMARK
F
F
F
F
F
F
G HA
REF NO.
PART NO.
DESCRIPTION
REMARK
R809
1-216-073-00 RES,CHIP
10K
5%
1/10W
R811
R812
R813
R814
R815
1-216-661-11
1-216-658-11
1-216-049-91
1-214-921-00
1-216-659-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL
METAL CHIP
2.7K
2K
1K
220K
2.2K
0.50%
0.50%
5%
1%
0.50%
1/10W
1/10W
1/10W
1/2W
1/10W
R816
R817
R818
R819
R820
1-216-659-11
1-216-677-11
1-216-683-11
1-216-667-11
1-216-659-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
12K
22K
4.7K
2.2K
0.50%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R821
R823
R824
R825
R826
1-216-073-00
1-216-049-91
1-216-061-00
1-216-679-11
1-216-659-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
10K
1K
3.3K
15K
2.2K
5%
5%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R827
R830
R831
R832
R833
1-216-061-00
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
3.3K
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R901
R902
R903
R904
R906
1-202-725-00
1-202-725-00
1-216-073-00
1-216-073-00
1-216-057-00
SOLID
SOLID
RES,CHIP
RES,CHIP
RES,CHIP
3.3M
3.3M
10K
10K
2.2K
20%
20%
5%
5%
5%
1/2W
1/2W
1/10W
1/10W
1/10W
R907
1-216-061-00 RES,CHIP
3.3K
5%
1/10W
<RELAY>
RY1
!
RY901 !
1-515-738-11 RELAY
1-515-738-11 RELAY
REF NO.
PART NO.
!
1-762-300-11 SWITCH, AC POWER SEESAW
REMARK
<VARISTOR>
VDR1
VDR2
! 1-801-073-31 VARISTOR TNR14V471K660
! 1-810-622-11 VARISTOR
*************************************************************
* A-1372-133-A MOUNTED PWB, HA (14G5,BKM-10R)
****************
<CAPACITOR>
C201
C202
C203
C204
C205
1-126-206-11
1-126-206-11
1-126-206-11
1-126-206-11
1-126-206-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
100MF
100MF
100MF
100MF
20%
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C206
C207
C211
C212
C213
1-126-206-11
1-126-206-11
1-163-031-11
1-163-031-11
1-163-031-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100MF
100MF
0.01MF
0.01MF
0.01MF
20%
20%
6.3V
6.3V
50V
50V
50V
C214
C215
C216
C217
C301
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C302
C303
C304
C305
C306
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C307
C308
1-163-031-11 CERAMIC CHIP
1-163-031-11 CERAMIC CHIP
0.01MF
0.01MF
50V
50V
<CONNECTOR>
<SWITCH>
S901
DESCRIPTION
CN201
CN202
* 1-564-005-11 PIN, CONNECTOR 6P
* 1-564-009-11 PIN, CONNECTOR 10P
<TRANSFORMER>
<DIODE>
T1
T2
T3
T201
T301
! 1-424-461-11 TRANSFORMER, LINE FILTER
! 1-424-461-11 TRANSFORMER, LINE FILTER
! 1-429-283-11 TRANSFORMER, CONVERTER (PFT)
! 1-431-703-11 TRANSFORMER, CONVERTER
! 1-431-704-11 TRANSFORMER, CONVERTER
D201
D202
D203
D204
D205
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
D206
D207
D208
D209
D210
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
D211
D212
D213
D214
D215
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
D216
D217
D218
D219
D220
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
<THERMISTOR>
THP1
!
1-808-059-31 THERMISTOR, POSITIVE
<TEST PIN>
TP31
TP32
TP33
TP201
TP202
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
PIN, POST
PIN, POST
PIN, POST
PIN, POST
PIN, POST
TP207
TP301
TP302
TP303
TP304
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
1-537-864-11
PIN, POST
PIN, POST
PIN, POST
PIN, POST
PIN, POST
TP305
1-537-864-11 PIN, POST
9-31
HA HB
REF NO.
PART NO.
DESCRIPTION
D221
D222
D223
D224
D225
8-719-404-49
8-719-404-49
8-719-987-45
8-719-987-45
8-719-987-45
DIODE MA111
DIODE MA111
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
D226
D231
8-719-987-45 DIODE CL-155Y/PG-CD
8-719-158-19 DIODE RD6.2SB
REMARK
<IC>
IC201
IC202
8-752-842-86 IC CXP2003M
8-752-842-86 IC CXP2003M
<TRANSISTOR>
Q201
Q202
Q203
REF NO.
PART NO.
DESCRIPTION
REMARK
S215
1-692-037-31 SWITCH, KEY BOARD (MANUAL CONTRAST)
S216
S217
S218
S219
S220
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
SWITCH, KEY BOARD (MANUAL BRIGHT)
SWITCH, KEY BOARD (MANUAL CHROMA)
SWITCH, KEY BOARD (MANUAL PHASE)
SWITCH, KEY BOARD (MENU)
SWITCH, KEY BOARD (ENTER)
S221
S222
S231
S232
S233
1-692-037-31
1-692-037-31
1-473-469-11
1-473-469-11
1-473-469-11
SWITCH, KEY BOARD (UP)
SWITCH, KEY BOARD (DOWN)
ENCODER, ROTARY (CONTRAST)
ENCODER, ROTARY (BRIGHT)
ENCODER, ROTARY (CHROMA)
S234
1-473-469-11 ENCODER, ROTARY (PHASE)
*************************************************************
1-801-806-11 TRANSISTOR DTC144EKA-T146
8-729-921-12 TRANSISTOR 2SD1834
8-729-921-12 TRANSISTOR 2SD1834
* A-1372-134-A MOUNTED PWB, HB (14G5,BKM-10R)
****************
<RESISTOR>
<CAPACITOR>
R201
R202
R203
R204
R205
1-216-043-91
1-216-043-91
1-216-043-91
1-216-043-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
560
560
560
560
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R206
R207
R208
R209
R210
1-216-049-91
1-216-049-91
1-216-065-91
1-216-049-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
4.7K
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R211
R212
R213
R214
R215
1-216-085-00
1-216-095-00
1-216-085-00
1-216-095-00
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
33K
82K
33K
82K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R216
R217
R301
R302
R303
1-216-089-91
1-216-089-91
1-216-065-91
1-216-065-91
1-216-065-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R304
R305
R306
R307
R308
1-216-065-91
1-216-065-91
1-216-065-91
1-216-065-91
1-216-065-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
4.7K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C101
C102
C111
C112
C113
1-126-391-11
1-126-391-11
1-163-031-11
1-163-031-11
1-163-031-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
<CONNECTOR>
CN101
1-506-471-11 PIN, CONNECTOR 6P
<DIODE>
D101
D102
D103
D104
D105
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
D106
D107
D108
D109
D110
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
8-719-404-49
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
DIODE MA111
D111
D121
D122
D123
D124
8-719-158-19
8-719-987-45
8-719-987-45
8-719-987-45
8-719-987-45
DIODE RD6.2SB
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
D125
D126
D127
D128
D129
8-719-987-45
8-719-987-45
8-719-987-45
8-719-987-45
8-719-987-45
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
DIODE CL-155Y/PG-CD
D130
8-719-987-45 DIODE CL-155Y/PG-CD
<SWITCH>
S201
S202
S203
S204
S205
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
SWITCH, KEY BOARD (POWER)
SWITCH, KEY BOARD (DEGAUSS)
SWITCH, KEY BOARD (1)
SWITCH, KEY BOARD (2)
SWITCH, KEY BOARD (3)
S206
S207
S208
S209
S210
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
SWITCH, KEY BOARD (Del)
SWITCH, KEY BOARD (4)
SWITCH, KEY BOARD (5)
SWITCH, KEY BOARD (6)
SWITCH, KEY BOARD (0)
S211
S212
S213
S214
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
SWITCH, KEY BOARD (7)
SWITCH, KEY BOARD (8)
SWITCH, KEY BOARD (9)
SWITCH, KEY BOARD (Ent)
9-32
<IC>
IC101
IC102
8-752-842-86 IC CXP2003M
8-752-842-86 IC CXP2003M
<TRANSISTOR>
Q101
Q102
8-729-921-12 TRANSISTOR 2SD1834
8-729-921-12 TRANSISTOR 2SD1834
47MF
47MF
0.01MF
0.01MF
0.01MF
20%
20%
6.3V
6.3V
50V
50V
50V
HB HC
REF NO.
PART NO.
DESCRIPTION
REMARK
Q103
1-801-806-11 TRANSISTOR DTC144EKA-T146
<RESISTOR>
R101
R102
R103
R104
R105
1-216-043-91
1-216-043-91
1-216-043-91
1-216-043-91
1-216-043-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
560
560
560
560
560
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R106
R107
R108
R109
R110
1-216-043-91
1-216-043-91
1-216-043-91
1-216-043-91
1-216-043-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
560
560
560
560
560
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R112
R113
R114
R115
R116
1-216-097-91
1-216-049-91
1-216-049-91
1-216-049-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
1K
1K
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R117
R121
R122
R123
R124
1-216-065-91
1-216-085-00
1-216-095-00
1-216-085-00
1-216-095-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
33K
82K
33K
82K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R125
R126
R127
1-216-089-91 RES,CHIP
1-216-089-91 RES,CHIP
1-216-089-91 RES,CHIP
47K
47K
47K
5%
5%
5%
1/10W
1/10W
1/10W
<SWITCH>
S101
S102
S103
S104
S105
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
SWITCH, KEY BOARD (SHIFT)
SWITCH, KEY BOARD ( /16:9)
SWITCH, KEY BOARD ( ; /SYNC)
SWITCH, KEY BOARD ( ; /BLUE ONLY)
SWITCH, KEY BOARD (MONO/R)
S106
S107
S108
S109
S110
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
1-692-037-31
SWITCH, KEY BOARD (APT/G)
SWITCH, KEY BOARD (COMB/B)
SWITCH, KEY BOARD (F1/F3)
SWITCH, KEY BOARD (F2/F4)
SWITCH, KEY BOARD (ADDRESS/SAFE AREA)
REF NO.
PART NO.
DESCRIPTION
REMARK
C59
C60
C61
C62
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
C63
C64
C65
C66
C67
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C68
C71
C81
C82
C83
1-163-031-11
1-163-031-11
1-126-206-11
1-124-635-00
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT
ELECT CHIP
0.01MF
0.01MF
100MF
220MF
100MF
20%
20%
20%
50V
50V
6.3V
6.3V
6.3V
C84
C85
C86
C87
C88
1-126-206-11
1-126-206-11
1-126-206-11
1-126-206-11
1-126-206-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
100MF
100MF
100MF
100MF
20%
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C89
C90
C92
C93
1-126-206-11
1-126-206-11
1-126-206-11
1-126-206-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100MF
100MF
100MF
100MF
20%
20%
20%
20%
6.3V
6.3V
6.3V
6.3V
<CONNECTOR>
CN1
CN2
CN3
CN4
CN5
1-774-534-11
1-506-474-11
* 1-564-009-11
* 1-564-005-11
1-506-471-11
CONNECTOR, IC CARD
PIN, CONNECTOR 9P
PIN, CONNECTOR 10P
PIN, CONNECTOR 6P
PIN, CONNECTOR 6P
<DIODE>
*************************************************************
D1
D2
D3
D4
D5
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
8-719-158-19
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
DIODE RD6.2SB
D6
D7
D8
8-719-158-19 DIODE RD6.2SB
8-719-158-19 DIODE RD6.2SB
8-719-158-19 DIODE RD6.2SB
<IC>
* A-1375-155-A HC COMPLETE PWB (14G5,BKM-10R)
****************
1-540-044-11 SOCKET, IC (ISC1)
7-628-253-35 SCREW +PS 2X8
7-688-001-01 W 2, SMALL
IC1
IC2
IC3
IC4
IC5
8-759-467-21
8-759-991-19
8-759-186-47
8-759-186-63
8-759-186-77
IC HD6473258P10-EG2.0
IC PST529CMT
IC TC74VHC138F
IC TC74VHC245F
IC TC74VHC541F
IC6
IC7
IC8
IC9
IC10
8-759-186-77
8-759-175-27
8-759-186-63
8-759-186-30
8-759-186-30
IC TC74VHC541F
IC TC74VHC574F
IC TC74VHC245F
IC TC74VHC14F
IC TC74VHC14F
IC11
IC12
IC13
IC14
IC16
8-759-175-27
8-759-174-16
8-759-289-43
8-759-186-26
1-810-899-11
IC TC74VHC574F
IC TC74VHC244F
IC LTC490CS8
IC TC74VHC02F
IC MAX877CSA
IC21
8-759-186-44 IC TC74VHC125F
<CAPACITOR>
C1
C2
C4
C50
C52
1-163-227-11
1-163-227-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
10PF
0.01MF
0.01MF
0.01MF
0.5PF 50V
0.5PF 50V
50V
50V
50V
C53
C54
C55
C56
C57
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
0.01MF
0.01MF
0.01MF
50V
50V
50V
50V
50V
C58
1-163-031-11 CERAMIC CHIP
0.01MF
50V
9-33
HC HD
REF NO.
PART NO.
DESCRIPTION
REMARK
<COIL>
L1
L2
L3
1-412-539-11 INDUCTOR
1-412-537-31 INDUCTOR
1-412-537-31 INDUCTOR
150µH
100µH
100µH
<TRANSISTOR>
Q2
Q4
Q6
1-801-806-11 TRANSISTOR DTC144EKA-T146
8-729-122-13 TRANSISTOR 2SA1221-K
1-801-806-11 TRANSISTOR DTC144EKA-T146
<RESISTOR>
REF NO.
PART NO.
DESCRIPTION
REMARK
R56
R57
R58
1-216-097-91 RES,CHIP
1-216-097-91 RES,CHIP
1-216-097-91 RES,CHIP
100K
100K
100K
5%
5%
5%
1/10W
1/10W
1/10W
R60
R61
R62
R63
R64
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R65
R66
R67
R68
R69
1-216-089-91
1-216-089-91
1-216-089-91
1-216-097-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R70
R71
R72
R73
R74
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R75
R76
R77
R78
R79
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R80
R81
R82
R83
R84
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R85
R86
R87
R88
R89
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R90
R91
R92
R93
R94
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R1
R2
R3
R4
R5
1-216-073-00
1-216-295-91
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
SHORT
RES,CHIP
RES,CHIP
RES,CHIP
10K
0
10K
10K
10K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R6
R7
R10
R11
R12
1-216-073-00
1-216-097-91
1-216-057-00
1-216-069-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
100K
2.2K
6.8K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R13
R14
R15
R16
R18
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R19
R20
R21
R22
R23
1-216-073-00
1-216-073-00
1-216-049-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R24
R25
R26
R27
R28
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R31
R32
R33
R34
R35
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R36
R37
R38
R40
R41
1-216-089-91
1-216-089-91
1-216-089-91
1-216-065-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R42
R43
R44
R45
R48
1-216-073-00
1-216-073-00
1-216-073-00
1-216-089-91
1-216-061-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10K
10K
47K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R49
R50
R51
R52
R53
1-216-061-00
1-216-097-91
1-216-097-91
1-216-097-91
1-216-097-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
3.3K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
D101
D102
D103
D104
D105
R54
R55
1-216-097-91 RES,CHIP
1-216-097-91 RES,CHIP
100K
100K
5%
5%
1/10W
1/10W
*************************************************************
<CRYSTAL>
X1
1-767-892-21 VIBRATOR, CRYSTAL (20MHz)
*************************************************************
* A-1372-136-A MOUNTED PWB, HD (14G1/20G1,BKM-10R)
****************
<CONNECTOR>
9-34
CN101
CN102
1-565-269-11 SOCKET, CONNECTOR (D-DUB,L) 9P
1-506-474-11 PIN, CONNECTOR 9P
<DIODE>
8-719-037-00
8-719-037-00
8-719-037-00
8-719-037-00
8-719-037-00
DIODE RD6.2SB2-T1
DIODE RD6.2SB2-T1
DIODE RD6.2SB2-T1
DIODE RD6.2SB2-T1
DIODE RD6.2SB2-T1
P TA TB YA YB
REF NO.
PART NO.
DESCRIPTION
REMARK
REF NO.
PART NO.
<CAPACITOR>
<CAPACITOR>
1-137-150-11 MYLAR
1-137-150-11 MYLAR
1-136-157-00 FILM
0.01MF 10%
0.01MF 10%
0.022MF 5%
100V
100V
50V
* 1-573-986-11
* 1-564-514-11
* 1-508-766-00
1-766-240-11
PIN, CONNECTOR (PC BOARD) 5P
PLUG, CONNECTOR 11P
PIN, CONNECTOR (5MM PITCH) 4P
PIN, CONNECTOR (PC BOARD) 2P
1-107-877-11 ELECT
1000MF
20%
10V
<CONNECTOR>
CN6
CN7
CN8
<DIODE>
D901
C101
CN1
CN2
CN3
CN4
CN5
<CONNECTOR>
CN901
CN902
CN903
CN904
REMARK
* A-1390-772-A TB MOUNT
****************
P MOUNT (not supplyed)
*******
C901
C902
C903
DESCRIPTION
1-774-525-11
1-774-525-11
1-774-525-11
1-774-537-11
1-774-525-11
SOCKET, CONNECTOR 64P
SOCKET, CONNECTOR 64P
SOCKET, CONNECTOR 64P
CONNECTOR PIN (PC BOARD) 50P
SOCKET, CONNECTOR 64P
* 1-564-521-11 PLUG, CONNECTOR 6P
1-564-523-11 PLUG, CONNECTOR 8P
1-564-524-11 PLUG, CONNECTOR 9P
8-719-302-43 DIODE EL1Z
<COIL>
<NEON LAMP>
L101
NL901
NL902
1-519-526-11 LAMP, NEON
1-519-526-11 LAMP, NEON
1-406-661-11 INDUCTOR
0µH
*************************************************************
* A-1373-641-A YA MOUNT
****************
<RESISTOR>
R901
R902
R903
R903
1-215-437-00
1-215-437-00
1-215-425-00
1-215-427-00
METAL
METAL
METAL
METAL
4.7K
4.7K
1.5K
1.8K
1%
1%
1%
1%
1/4W
1/4W
1/4W (20G1)
1/4W
(14G1/14G5)
1/4W
R904
1-215-437-00 METAL
4.7K
1%
R905
R906
R906
1-215-437-00 METAL
1-215-425-00 METAL
1-215-427-00 METAL
4.7K
1.5K
1.8K
1%
1%
1%
R907
R908
1-249-377-11 CARBON
1-249-425-11 CARBON
0.47
4.7K
5%
5%
1/4W
1/4W (20G1)
1/4W
(14G1/20G1)
1/4W
F
1/4W
R909
1-247-887-00 CARBON
220K
5%
1/4W
<CONNECTOR>
CN101
1-564-517-11 PLUG, CONNECTOR 2P
<DIODE>
D101
D102
D103
D104
D105
8-719-061-96
8-719-061-96
8-719-061-96
8-719-061-96
8-719-061-96
DIODE SLR-325DCT31
DIODE SLR-325DCT31
DIODE SLR-325DCT31
DIODE SLR-325DCT31
DIODE SLR-325DCT31
<RESISTOR>
<TRANSFORMER>
T901
T901
!
!
X-4035-493-1 FBT ASSY, NX-4141//J1F4 (20G1)
X-4035-494-1 FBT ASSY, NX-4141//J1F4 (14G1/14G5)
*************************************************************
* A-1390-771-A TA MOUNT
****************
R101
R102
R103
R104
R105
1-216-061-00
1-216-061-00
1-216-061-00
1-216-061-00
1-216-061-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
3.3K
3.3K
3.3K
3.3K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R106
R107
R108
R109
R110
1-216-061-00
1-216-061-00
1-216-061-00
1-216-061-00
1-216-061-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
3.3K
3.3K
3.3K
3.3K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
<CONNECTOR>
*************************************************************
CN11
CN12
CN13
CN14
CN15
1-774-525-11
1-774-525-11
1-774-525-11
1-774-537-11
* 1-564-514-11
SOCKET, CONNECTOR 64P
SOCKET, CONNECTOR 64P
SOCKET, CONNECTOR 64P
CONNECTOR PIN (PC BOARD) 50P
PLUG, CONNECTOR 11P
CN16
CN17
CN18
CN19
CN20
1-564-511-11
* 1-564-507-11
* 1-564-704-11
* 1-564-505-11
1-564-506-11
PLUG, CONNECTOR 8P
PLUG, CONNECTOR 4P
PIN, CONNECTOR (SMALL TYPE) 2P
PLUG, CONNECTOR 2P
PLUG, CONNECTOR 3P
* A-1373-638-A YB MOUNT (14G1)
****************
* A-1373-642-A YB MOUNT (14G5/20G1)
****************
<DIODE>
D201
D202
D203
8-719-061-96 DIODE SLR-325DCT31
8-719-053-43 DIODE SLR-325VCT31
8-719-060-27 DIODE SLR-325MCT31
*************************************************************
*************************************************************
9-35
YB
REF NO.
PART NO.
DESCRIPTION
REMARK
* A-1373-636-A YC MOUNT (14G1)
****************
* A-1373-643-A YC MOUNT (14G5/20G1)
****************
<CONNECTOR>
CN301
CN302
1-506-487-11 PIN, CONNECTOR 8P
1-774-533-11 SOCKET, SMALL TYPE DIN (8P)
<CHIP CONDUCTOR>
JR301
JR302
JR303
JR304
1-216-295-91
1-216-295-91
1-216-295-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
0
0
0
0
*************************************************************
MISCELLANEOUS
*************
V901
V901
V901
V901
V901
1-452-032-00
1-452-094-00
1-500-249-11
1-500-278-11
1-543-653-11
MAGNET,DISC:10MM
MAGNET, ROTA TABLE DISK:15MM
BEAD, FERRITE (CASE)(14G1/14G5)
FILTER, CLAMP (FERRITE CORE)(20G1)
CORE ASSY, BEAD(DIVISION TYPE)(20G1)
!
!
!
4-051-735-22
4-051-736-21
1-411-657-11
1-411-658-21
1-411-659-21
PIECE A(75), CONV. CORRECT
PIECE A(90), CONV. CORRECT (20G1)
COIL, LANDING CORRECTION (20G1)
COIL, LANDING CORRECTION (14G1/14G5)
COIL, DEMAGNETIC (20G1)
!
!
!
!
!
1-411-660-21
1-452-436-41
8-451-470-13
8-451-473-11
8-453-003-11
COIL, DEMAGNETIC (14G1/14G5)
NECK ASSY, CRT (NA292)(15G1/14G5)
DY Y20MPD-M (20G1)
DY Y14MPDT (14G1/14G5)
NA3012(M) (20G1)
! 8-736-378-05 PICTURE TUBE (20MT1)(20G1E)
! 8-736-380-05 PICTURE TUBE (20MT3)(20G1U)
! 8-736-388-05 PICTURE TUBE (20MT1(S))(20G1A)
! 8-738-333-05 PICTURE TUBE (14MT1)(14G1E/14G5E/14G1A/14G5A)
! 8-738-335-05 PICTURE TUBE (14MT3)(14G1U/14G5U)
*************************************************************
ACCESSORY & PACKING MATERIAL
****************************
3-170-078-01
3-701-623-01
3-862-434-11
4-051-484-01
4-051-743-01
!
!
4-396-077-01 JOINT (20G1)
1-534-827-14 CORD POWER (14G1U/14G5U/20G1U)
1-590-151-11 CORD SET, POWER 10A/250V
(14G1A/14G1E/14G5A/14G5E/20G1A/20G1E)
* 4-051-298-01 CUSHION (UPPER) (ASSY)(20G1)
* 4-051-299-01 CUSHION (LOWER) (ASSY)(20G1)
* 4-051-321-02
* 4-051-322-01
* 4-051-574-01
* 4-051-575-01
* 4-051-580-01
9-36
HOLDER (B), PLUG
BAG, POLYETHYLENE
MANUAL, OPERATION (Japanese/English)
LABEL, TALLY (20G1)
PLATE, TALLY (14G1/14G5)
INDIVIDUAL CARTON (20G1)
TRAY (20G1)
CUSHION (UPPER)(ASSY)(14G1)
CUSHION (LOWER)(ASSY)(14G1)
CUSHION (UPPER)(ASSY)(14G5)
REF NO.
PART NO.
DESCRIPTION
* 4-051-581-01
* 4-051-705-01
* 4-051-708-03
* 4-058-814-01
* 4-058-815-01
CUSHION (LOWER)(ASSY)(14G5)
INDIVIDUAL CARTON (14G1)
INDIVIDUAL CARTON (14G5)
HOLDER (20G1)
HOLDER (14G1)
* 4-058-816-01
* 4-377-015-01
* 4-381-155-01
* 4-381-155-11
HOLDER (14G5)
BAG, PROTECTION (14G1)
BAG, PROTECTION (20G1)
BAG, PROTECTION (14G5)
REMARK
SECTION 10
BLOCK DIAGRAM
Block
Function
Page
Overall (1/2)
— ............................................................................................. 10-2
Overall (2/2)
— ............................................................................................. 10-3
BK (1/4)
Micro Computer, D/A Converter, Pulse Generator ................. 10-4
BK (2/4)
Signal Input Select, Signal Processing .................................... 10-5
BK (3/4)
Pulse Insert, Signal Process..................................................... 10-6
BK (4/4)
RGB Drive Out, RGB Drive IK/V Control ............................. 10-7
BC (1/2)
Main CPU, In/Out Expander, Remote Controller ................... 10-8
BC (2/2)
In/Out Expander, SYNC Generator ........................................ 10-9
E (1/2)
Micro Computer, H/V Signal Generator, Deflection Drive .... 10-10
E (2/2)
PWM Control, DF Control ...................................................... 10-11
G
Main Rect, ±6V REG, ±15V REG, +B REG, D5V REG ....... 10-12
HA, HB, HC,HD Function Select, System Control, Relay ................................. 10-13
10-1
OVERALL (1/2)
Q309
BK
ANALOG
1
IC101,102
Q100-105
Y/G Y/G BUFFER
2Y/2G
CLAMP
Y/G
Y/G SELECT
IN
Y/G
OUT
IC306,307
Q352-354
IC304
G BUFFER
IC101
Q108
SWITCH
Y BUFFER
SWITCH
G CLAMP
OVERALL (1/2)
IC312-314
Q376-379
IC310
Q375
IC310
SWITCH
G BUFFER
SWITCH
G
CONTRAST/BRT
CONTROL
Q350,351
G SET UP
G 100 IRE
IC311,313
BUFFER
G REF SEL
IC504
IC506,507
Q542-544
Y/G-Y MIX
IC305,Q306,307
G-Y
MATRIX
AMP
Q506
OUT
SWITCH
IC500,300
B-Y CLAMP OFFSET B-Y REF SEL
BUFFER
B-Y PULSE LEVEL
2
R BUFFER
R-Y/R
OUT
R-Y CLAMP OFFSET
R-Y PULSE LEVEL
IC301
SWITCH
IC500,300
R-Y REF SEL
BUFFER
IC800
Q800,801
SYNC BUFFER
SELECT
SYNC
OUT
SYNC INT/EXT
SYNC SEP SEL
IC800,801,802,804,805
Q820,824,826,827
CL-P BUFFER
CLAMP PULSE GEN
CLAMP DLY CTRL
IC803,Q825
H SYNC SEP
H SYNC BUFFER
Q822,823,828,829
Q802-819
SYNC AGC
V SYNC SEP
B SET UP
B 100 IRE
IC511,513
BUFFER
B REF SEL
IC104
IC106,107
Q142-144
Q140,141
Q107
PR
BUFFER
SWITCH
Y/PR MIX
RGB SW
IC912,Q902
CONT O,V BLK1
MONO SW
MONO SIGNAL OFF
IN
IC302-304,325
Q310
R-Y/R CLAMP
R-Y/R GAIN CONT
IC512-514
Q569-572
Q568
SWITCH
B BUFFER
B
CONTRAST/BRT
CONTROL
Q567
Y CLAMP PULSE
C CLAMP PULSE
Q164
R CLAMP
Q165
SWITCH
IC111,113
BUFFER
R REF SEL
R SET UP
R 100 IRE
IC112-114
Q166-169
IC110
R BUFFER
BLUE ONLY
IC131,331,531
CHAR RGB
BUFFER
CHARA RGB
IC508,509
CHAR BLK SW
CHAR BLK INSERT
CH BACK H/B
G CUTOFF
IC517,527-529
B DRIVE V/IK AMP
B DRIVE
B DRIVE V/IK
COMP
CONTROL
R
IC117,127-129
R DRIVE V/IK AMP
R DRIVE
R DRIVE V/IK
COMP
CONTROL
IC319
SWITCH
G VIDEO AMP
B CUTOFF
SWITCH
IC519
SWITCH
IC119
AFC PULSE
H PULSE
PULSE
V BLK P1
GENERATOR
V SP
H BLK
Q821
SYNC SEP
SWITCH
PULSE OUTPUT
(12 PULSE LINE)
Q705,706
BLK OUT
G1
SWITCH
VIDEO TIMING P
IC705
Q700-702
IC700-703
IC902,903,906-911
IC706,707
SIGNAL SELECT VIDEO COMP
LATCH
3
FROM OPTION
KR
IC121-124,126
BIAS CLAMP
BIAS CLAMP
CONTROL
G2 CONTROL
IC710,711,728,730-732,734-736
Q177,178
TRANSIENT
OFF SW
R VIDEO AMP
CHAR BLK
VS
KB
IC521-524,526
BIAS CLAMP
BIAS CLAMP
CONTROL
SWITCH
BIAS REF,CH LEVEL
DRIVE REF,BIAS P
KG
Q580,581
TRANSIENT
OFF SW
B VIDEO AMP
IC117
R CUTOFF
Q387,388
TRANSIENT
OFF SW
IC321-324,326
BIAS CLAMP
BIAS CLAMP
CONTROL
SWITCH
IC115,117,118
Q200,170-172,174-176
R BUFFER
PULSE INSERT
R DRIVE AMP
R DRIVE V
R DRIVE IK
IC317
IC517
IC116
R
CONTRAST/BRT
CONTROL
SWITCH
IC317,327-329
G DRIVE V/IK AMP
DRIVE
G DRIVE V/IK G
COMP
CONTROL
IC515,517,518
Q600,573-575,577-579
B BUFFER
PULSE INSERT
B DRIVE AMP
B DRIVE V
B DRIVE IK
R BUFFER
IC110
IC315,317,318
Q400,380-382,384-386
G BUFFER
G DRIVE AMP
IC516
G
B BUFFER
Q106
IC301,302
Q300-305
R-Y/R BUFFER
2PR/2R
CLAMP
PR/R R-Y/R SELECT
IN
Y/PB MIX
IC510
B CLAMP
SWITCH
PULSE INSERT
G DRIVE V
G DRIVE IK
G BUFFER
S PULSE
B-Y/B
Q540,541
Q507
PB
BUFFER
HS
IN
IC501
IC502-504,525
Q510
B-Y/B CLAMP
B-Y/B GAIN CONT
B
Q374
B BUFFER
IC501,502
Q500-505
B-Y/B BUFFER
2PB/2B
CLAMP
PB/B
B-Y/B SELECT
IC316
G2 CONTROL
G2 CTRL
Q179,389,582
TRANSIENT
OFF SW
BIAS & DRIVE P
IC900
SYSTEM CONTROL SIGNAL
MISO
(46 SIGNAL LINE)
SUB-CPU
SCLK
EEP-ROM
BUFFER
MOSI
D/A CONVERTER
CH SLOT 3
RESET
BRIGHT
OVER
IC701,704
IC901,904
BRT CENTER
LOAD
BRT
BRT
ABL ABL CONTROL
CONTROL
CONTRAST BUFF
CONTR
(BVM-14G5 only)
1
TO HC
AFC P,V BLK P2
4
2
(BVM-14G1/20G1 only)
3
1
RXD,TXD
RXD,TXD
IC7,8,11,16,17
5
HS,VS
OCTL BUFFER
INVERTER AFC P,V BLK 2
HD
4
6
1
IC12
CN3
REMOTE 1
IN
MISO,MOSI,S CLK
CN4
REMOTE 1
OUT
6
9
6
5
OPTION
6
5
1
MAIN
MICRO COMPUTER
IC121
CLOCK
DRIVER
WR,RD
INVERTER
IC2,Q3,10
RESET
BACK-UP/RESET
SIO,CC
RESET
BACK-UP 5V
IC22-24
A0
HS,VS
OPTION
IC36
(RTS,RXD,TXD)
RS232C
INTERFACE
X2
4.9152MHz
CHARACTER
GENERATOR
CHARA BLK CHARA RGB
SAMPLE PULSE
GENERATOR
INVERTER
IC30,31
CLOCK
DRIVER
PD4-PD7
RESET
SLOT3,2
IC34
SLOT
RECEIVER
IC32,33
SLOT
DRIVER
CC SIGNAL
IC124
AFC P
IC5
IC19-21
8 TO1
SELECTOR
A0-A2
IN/OUT PROT
EXPANDER
SYNC PLL
CLOSE
CAPTION
IC125
IC701
BLANKING
AMP
G1
IC104,105,107,108
LINE COUNTER
DOT CLK COUNTER
INT SIGNAL DATA
IC601,Q601-603
G2 CONTROL
H STAT CONTROL
IC110
P/S
CONVERTER
RV501
H STAT
CHARA RGB
CHARA BLK
INVERTER
2/2
IC113,115,117
D13,111-113
SAD BLK
NAND
SAD RGB SEP
YA
+12V
D/A CONVERTER
Y/G,PB/B,PR/R BUFFER
TALLY
Y/G
HP0-HP7
H0,H1
V0-V3
VP0-VP3
IC120,106,123
HV
IC109,111,Q106-113
YB
RV101
INT SIGNAL LVL
+5V
SYNC GEN
COUNTER
D FLIP.FLOP
BUVD00-BUVD02,BUVD10-BUVD12,BUVD20,BUVD21
5
PICTURE TUBE
6
5
7
5
IC61-63
Q51,52,151,152
SDI CC PULSE
GENERATOR
C
G2
CTRL
IC116,114,121,122
REMOTE/
ISR/RS-232C
CONTROLLER
IC27,28
RS232C
INTERFACE
IN/OUT PROT
EXPANDER
A0-A2
IC29
REMOTE 2
DRIVER
CN5
REMOTE 2
9
LITUM
BATTERY
1
CN302
9
X1
20MHz
IC6
CS
PROGRAM ROM
S-RAM
ADDRESS DECODER CS
IC15
RXD,TXD IC25,26
RXD,TXD
RS485
INTERFACE
RTS,TXD,DTR
DSR,RXD,CTS
RXD,RXD
Q4-7 +5V,+12V
+5V,+12V
SWITCH
IC3,4,9,10,13
RXD
TXD,TXD
RS422
INTERFACE
1
CN6
ISR
YC
5
5
CHARA 1-CHARA 3
DATA BUS
ADDRESS BUS
CONTROL BUS
TXD,SCK
INT BUS
DRIVER
IC14
9
IC1
KR
KG
KB
CHARA RGB
CHARA BLK
IC35,8
9
AFC,P V BLK P2
HS,VS
IRQ0-IRQ2
CONTROL
6
OVERLOAR
BC
STANDBY
POWER
BK, HD, YC, BC, C, YA, YB BOARDS
10-2
A
B
C
D
OVERALL BLOCK (1/2)
10-2
E
F
G
H
OVERALL (2/2)
E
IC702
ROTATION/
CY(V) OUT
Q721,722
Q725-727,729
BUFFER/ CY HP+
AMP
L SCLK,L MOSI
IC802
IC803
IC703
D/A
CONVERTER
EEP-ROM
MOSI,SCLK
MISO,CH SLOT 2
SIGNAL
GENERATOR
H STAT
IC001,623,625,628
Q622,X001
X801
20MHz
IC202-204,628,Q271-273
H PARA
AMP/BUFFER
V SP
H PARA CLAMP
V SP PHASE
IC611,602,613,627,628
Q552-554
HV DRIVE
AMP
Q561
HV REG OCP
DETECT
V SAW AMP
IC091,Q091
H CENTER
AMP/BIAS
V BLK P1
H BLK/V BLK
V BLK P2
PULSE GENERATOR
H BLK P
PROT
IC501
ABL
4
BUFFER
ABL
HV RTN(AC)
IC501
HV RTN(DC)
BUFFER
IK PROT
HV PROT
DFX
DFX DRIVE
H LIN AMP
T901 FBT
T151 HLT
T052 HOT
+B Q061
H SIZE REG
SWITCHING
S901
MAIN POWER
RY1
D2
DC REF
D1
Q4,5
PROTECT
RESET
HP
AFC PULSE OUT
IC101
Q101,103,104,109
COMPARATOR
PFC OFF
BUFFER
IC32,Q32
GAIN
CONTROL
IC102,Q105,106
COMPARATOR
LATCH
IC31,Q31
PFC CONTROL
PFC OUT
HV CTL
P
G2
5
3
SWITCH FUNCTION
S231 CONTRAST
S232
BRIGHT
S233
CHROMA
S234
PHASE
IC201,202
SERIAL-PARALLEL
CONVERTER
HV OFF
IK PROT
HV OVP
IC901
+12V REG
+16V OUT
+12V
SWITCH
+6V OUT
+6V
D208,Q212,213
–6V
–6V OUT
D209,Q214,215
–16V
–16V OUT
IC203
+16V REG
Q802,816,817
Q904
RESET
SWITCH
HT– (H1)
D303
+6.5V RECT
IC301,Q303-305
PWM CONTROL
CONVERTER OUT
IC801,802,804
Q801
+5V OVP
+15V OVP
COMPARATOR
DC REF
+120V RECT
6
+120V
+120V REG
ISORATOR
SWITCH
IC101,102
SERIAL-PARALLEL
CONVERTER
IC801,D3,4
Q806-811
Q812-815
IC803
LATCH
PROT SW
RESET
Q805
PFC
PROT SW
5
(BVM-14G5 only)
IC9-11
EDGE TRIG F/F
INVERTER
IC4,7,8
D0-D7 CARD ADDRESS
HIGH
BUFFER
MEMORY
IC3,5,6,10,14,21
CARD
A0-A20 ADDRESS DECODER
BUFFER
DECODER
IC12
MISO
MISO
BUS SELECT
CE1,MOSI,SCLK
CE2,MOSI,SCLK
G PROT 1
G PROT 2
PROTECT
ENCODER G PROT 3
G PROT 4
PFC FAILURE
HB
S101-110
SWITCH FUNCTION
S101
S102
S103
S104
MONO
S105
APT
S106
COMB
S107
F1
S108
F2
S109
ADDRESS
S110
G
TO BC
RXD,RXD,TXD,TXD
IC13
RXD
RS422 TXD
DRIVER
DATA BUS
D0-D7
ADDRESS BUS
A0-A15
CONTROL BUS
RD,WR
IC2
B
C
D
MICRO
COMPUTER
X1
20MHz
TXDO,SCKO
RXDO
SHIFT
16:9
SYNC
BLUE ONLY
R
G
B
F3
F4
SAFE AREA
5
E, G, DY, P, HA, HB, HC, HD BOARDS
10-3
E
4
RESET
(BVM-14G5,BKM-10R only)
10-3
A
9
S201-210
HC
HT+ (H2)
IC302
6
MONITOR
POWER ON
E PROT
D304
PH301,802
1
S231-234
SWITCH FUNCTION
S201
POWER
S202
DEGAUSS
S203-209
0-9
S211-213
S210
Del
S214
Eet
S215 CONTRUST
S216
BRIGHT
S217
CHROMA
S218
PHASE
S219
MENU
S220
ENTER
S221
UP
S222
DOWN
D+5V
+16V
Q903
HD
DEGAUSS
DEG SW
D207,Q210,211
ISORATOR
PH803
ISORATOR
Q107,108,110
D105
ISORATOR
RESET
PH901
SWITCH
FV2
11
DY
2
(BKM-10R only)
D206,Q208,209
IC201,Q203-205
PWM CONTROL
CONVERTER OUT
V DY
HA
D+5V OUT
D36
DFY
Q551
HV REG
SWITCHING
IC531
+20V RECT
18
16
ABL
IK PROT
D555
+600V RECT
IC503,Q501,502
PWM CONTROL
PWM DRIVE
DFX
5
7
V STOP
Q555
HV OUT
SWITCHING
+15V REG
Q102
RELAY
DETECT
FV1
17
H STOP
DISCHARGE
Q300,301,306
2
AFC P
Q121,122,131-133
H/V STOP
DETECTOR
+B
HV PROT
H DY
V DY
V DY RET
Q111,112,IC627
PH201
F1
T4A/250V
HV RTN(DC)
15
HV RTN(AC)
H DY RET
H DY
–6V
V OUT
D204,Q207,IC202
T3 PFCT
2
6
IC031
KICK
MAIN
RECT
Q7
+15V
FBT(C)
13
IC1,Q6
Q1,2,D5
1
14
H CENTER
AMP
Q901,902
RY901
FBT(H)
IC101
+15V
DEGAUSS COIL
AC IN
100-240V
50/60Hz
T301
DFT
Q151,152,155-157,159
Q051,053,054,T051
H DRIVE
H OUT
IC091
IC612
LANDING CORRECTION
COIL
DFY
Q301-304,306,307
DF MOD
H LIN CONV
7
VS AMP
2
V SAW
V PARA
1
NTC
Q321,322
IC071,Q071,072
PWM CONTROL
PWM OUT
SIGNAL
GENERATOR
H SYNC GEN
IC621,622,625,627
IC628,641,Q621,641
H/V SYNC PHASE
PULSE CLAMP
H/V SYNC SELECT
IC301,151
IC202,203
Q201
V PARA/
V SAW OUT
IC231
LANDING/
NTC OUT
HV OVP,IK PROT
HS,VS
CY(V)
CY(H)
DFY OUT
IC201
MICRO
COMPUTER SDA,SCL
Q802-804
Q807-809,815
E PROT
E PROT,POWER ON POWER ON SW
HV OCP SW
PROT SW
1
ROTATION
COIL
CV HP+
IC205
D/A
CONVERTER
RESET
DEGAUSS
G PROT 1-4
3
IC701
SIGNAL
GENERATOR
IC801
BUFFER
OVERALL (2/2)
OVERALL BLOCK (2/2)
F
G
H
BK (1/4)
FROM E 801-14a
AFC PULSE
1-19b
H PULSE
1-24a
IC731
(1/6)
13
12
IC731
(4/6)
1
2
5V
IC710
2
1
3
3
5
4
1
IC730(3/4)
9
10
8
FROM E 801-9a
V BLK P1
1-24b
2
FROM E 801-24a
FROM E 801-8a
FROM E 801-8b
VSP
V BLK P2
H BLK
5
6
6 IC711 IC736(4/4)
3
3
1
5
2
IC732
PULSE GENERATOR
IC734(2/3)
4 D0
Q0 2
5V
3
5 D1
Q0
2
12 D2
7
Q1
1
12
13
Q1 6
13
9
10
CLOCK Q2
Q2 11
Q3 15 IC730(4/4) IC731(5/6)
5
Q3 14
5
4
6
6
IC731(5/6)
9
8
1-9b
W B INSERT P-
IC736(1/4,2/4,3/4)
12
IC731
13
11
(2/6)
8
6 11
10
10
9
IC734
(1/3)
IC731
(3/6)
7 3
4
6
5
BK (1/4)
IC735(2/4)
8
10
9
BLACK SAMPLING P 2/4,3/4,4/4
WHITE SAMPLING P 2/4,3/4,4/4
4
WHITE INSERT P
W B INSERT P
W&DP
6 IC735(1/4)
4
5
13 IC728(1/4)
11
12
IC728(2/4)
1
3
2
1-25b
1-25a
IC735(3/4)
2
1
3
5V
IC734
(3/3)
9
IC730(1/4) IC728(4/4)
10
11
8 12
8 BLK
13 9
11
10
IC910 DAC
17
14
A01
A02
A03
A04
A05
A06
A07
A08
A09
A010
A011
A012
D1
CLK
D0
IC903
EEP ROM
3
FROM BC 1-26b
FROM BC 1-28b
FROM BC 1-28a
FROM BC 1-15b
RESET
SCLK
MOSI
CH SLOT 3
1-26b
1-28b
12
1-28a
2
1-31a
4
4/4
4/4
4/4
3/4
11
13
3
1
15
FROM E 801-23b
ABL
1-10a
5
IC901(1/2)
5
7
6
RDY
WRO
HAK
BUFC
INT 0
40
PI 1
41
PI 0
42
PO 7
55
P3 4
B DRIVE COMP
G DRIVE COMP
R DRIVE COMP
VIDEO COMP
IC901(2/2)
3
1
2
47
AO 2
44
45
46
48
49
56
PWC
58
WTO
PTO 59
TP901
SO 2 2
P4 4 64
-5V
CONT
15
4/4
4/4
BIAS P
3/4
BIAS & DRIVE P
BIAS SAMPLING P
4/4
4/4
BIAS CLAMP P
4/4
+120V
IC1
+5V REG
-6V REG
LD
18
19
2
3
4
5
6
7
8
9
12
13
H BLK
2/4
B-Y GAIN
R-Y CLAMP OFFSET
G 100 IRE
G SET UP
B SET UP
B 100 IRE
CLAMP P DLY
2/4
2/4
3/4
3/4
3/4
3/4
2/4
B-Y PULSE LEVEL
R-Y PULSE LEVEL
B-Y CLAMP OFFSET
R-Y GAIN
2/4
2/4
2/4
2/4
BLUE ONRY
RGB SW
BIAS REF
3/4
2/4
2/4
R 100 IRE
R SET UP
3/4
3/4
CH LEVEL
DRIVE REF
G2 REF
Y CLAMP OFFSET
PROG SW
3/4
3/4
4/4
2/4
2/4
Q705,706 TP700
HV BLK
BUFFER
G1
17
A01
A02
A03
A04
A05
A06
A07
A08
A09
A010
A011
A012
D1
16
CLK
14 D0
X900
8MHz
15
17
CH BACK H/B
BK SELECT
MONO
CONT O
IK/V SW
3/4
2/4
2/4
2/4
4/4
SYNC INT/EXT
CLAMP PULSE SEL
SYNC SEP SEL
W/B P SW
AUTO C/P P SW
2/4
2/4
2/4
1/4
3/4
R SEL
GB SEL
3/4
3/4
IC900(2/4)
5
6
4
16
14
15
17
16
14
15
17
16
14
15
17
LD
IC909 DAC
A01
A02
A03
A04
CLK
A05
D0
A06
LD
A012
IC911 DAC
A01
D1
A02
A03
A04
CLK
A05
D0
A06
LD
A012
IC907 DAC
A01
D1
A02
A03
CLK
A04
A05
D0
A06
LD
A012
IC906 DAC
D1
D1
A01
A02
A03
A04
A05
A06
A010
16
CLK
14 D0
15 LD
3/4
18
19
2
3
4
5
6
7
8
9
12
13
18
19
2
3
4
5
13
G BIAS IK
4/4
G DRIVE IK
4/4
G DRIVE V
4/4
G CUTOFF
4/4
18
19
2
3
4
5
13
B BIAS IK
4/4
B DRIVE IK
4/4
B DRIVE V
4/4
B CUTOFF
4/4
18
19
2
3
4
5
13
18
19
2
3
6
8
9
R BIAS IK
4/4
R DRIVE IK
4/4
R DRIVE V
4/4
R CUTOFF
4/4
CHROMA
2/4
IC704(2/2)
2
1
3
-12V REG
10-4
C
-12V
5-1
TO C 507-1
IC704(1/2)
5
7
6
BRT CENTER
BRIGHT
2
1
IC701
(1/3) TP701
15
3/4
BRT
10
MISO
B
-5V
IC3
MICRO COMPUTER
D/A CONVERTER
PULSE GENERATOR
BRT CONTROL
A
+5V
IC2
IC908 DAC
30
31
32
33
A15 34
35
A14
36
A13
A12 37
A11 38
A10 39
A05
A04
A03
A01
A00
IC904(1/2)
6
7 OVER LOAD
5
TP900
X1 24
3 SI 2
VIDEO TIMING P
DRIVE SAMPLING P
FROM G
IC735(4/4)
11
13
12
16
IC902
MICRO COMPUTER
1 CS
ADST 51
2 54
5
A06 43
SI1
SO
SI
6
6 CLK
P52
7
P53
20
8
P54
RESET
9
P55
52
Q900
SCK1
53
SO1
5
P51
4
P50
IC900(1/4,3/4,4/4)
9
8
1
SCK 2
X0 23
10
+B
1-2a
+B
1-2b
+6V
1-7a
+6V
1-7b
-6V
1-6a
-6V
1-6b
-15V
1-4a
-15V
1-4b
DIGITAL 5V 1-29a
DIGITAL 5V 1-29b
2/4,3/4
2/4,3/4
3/4
5V-2
5V
IC730(2/4)
3
1 IC728(3/4)
2
4
6
5V
5
3/4
D
1-27b
TO BC 1-27b
BK BLOCK (1/4)
10-4
E
F
G
H
BK (2/4)
Q101
BK SELECT
SWITCH
Q100,102
Q309
Y/G BUFFER
IN
ANALOG
Y/G
OUT
FROM OPTION
FROM BC 1-10b
2Y/2G
Y/G
1/4
Q501
BK SELECT
SWITCH
Q500,502
OUT
FROM OPTION
FROM BC 1-11b
G BUFFER
IC102 IC101(2/3)
(2/2)
2
3
15
1 1
2
10
IC501(1/3)
12
14
13
IC102
(1/2)
5
7
6
TP101
Q108
Q350,351
CLAMP
IC501(2/3)
IC502
(2/2)
15 5
7
6
2
1
1-14b
1-13b
IC503
1/4
R-Y GAIN
1/4
B-Y GAIN
TP502
GCA
DC CONT
GAIN CONT
1/4
B-Y PULSE LEVEL
1/4
BK SELECT
Q301
BK SELECT
SWITCH
Q300,302
R-Y/R BUFFER
IN
ANALOG
R-Y/R
OUT
FROM OPTION
FROM BC 1-12b
CLAMP
IC301(2/3)
IC302
(2/2)
15 5
7
6
2
1
1-16b
1-15b
TP102
L. L
CONV
5
IC303
1/4
R-Y CLAMP OFFSET
R-Y PULSE LEVEL
1/4,3/4
WHITE INSERT P
1/4
CONT 0
1/4
V BLK 1
1/4,3/4
W B INSERT P
1/4
MONO
1/4
5
1
3
GCA
DC CONT
GAIN CONT
IC500(2/3) IC300(1/2)
5
4 3
1
3
2
9
Q902
Q800
5V
IC803
(2/2)
Q6
Q
RD
3
7
Q828,829
12
13
11
IC302
(2/2)
2
1
3
IC320(2/2)
6
7
5
14
2
L. L
CONV
I/O
C
I/O
C
6
1
7
CLAMP PULSE SEL
1/4
SYNC SEP SEL
1/4
RGB SW
RGB SW
3
V SYNC SEP
12
11
IC803
(1/2)
Q 10
Q
RD
13
9
TP803
Y CLAMP PULSE
IC802 Q824
3
1 CLP DLY
2
CONTROL
Q820
5
7 CLP DLY
6
CONTROL
IC804
(1/2) 2
Q825
BUFFER
4
Q6
4
5
Q
IC800(2/3)
2
12
15
1
5V
10
11
7
5V
TP802
Q822,823
IC801
(1/2)
4
5
IC800(1/3)
BUFFER
12
13
14
2
Q6
Q
7
3
12
11
Q
Q
Q
Q
Q826
10
BUFFER
9
IC500(1/3)
13
14
12
11
13
IC801
(2/2)
5V
IC804
(2/2)
10
9
IC805
1
4
2
Q827
BUFFER
5
Q821
SYNC SEP SEL
SWITCH
1-20a
1-20b
TO E 1-13b
TO BC 1-20a
TO BC 1-20b
TO E 1-13a
HS
VS
10-5
A
1/4
CHROMA
13
1/4
3/4
IC325
1/4
11
H BLK
R
R MATRIX AMP
BUFFER
R-Y BUFFER
5
IC912(2/2)
2
5
7
1
6
3
IC912(1/2)
TP800
TP801
IC800(3/3)
Q802-819
3
4
4
SYNC AGC
5
5
9
SYNC INT/EXT
1/4
Q140,141
C CLAMP PULSE
BUFFER
1/4
IC104(2/3)
5
4
3
9
7
1/4,3/4,4/4 BLACK SAMPLING P
5V
BUFFER
OUT
2
Q107
1/4,3/4,4/4 WHITE SAMPLING P
CLAMP P DLY
IN
I/O
C
6
1
7
IC304(1/3)
Q801
ANALOG
SYNC
I/O
C
TP301
Q310
PROG SW
1/4
3/4
B MATRIX AMP
R BUFFER
IC301(3/3)
5
4
3
9
B
IC502
(2/2)
2
1
3
IC520(2/2)
6
7
5
IC525
2
10
1/4
Q540,541
BUFFER
IC504(1/3)
12
14
13
11
TP300
Q303-305
11
2PR/R
PR/R
3
B-Y BUFFER
Q106
IC301(1/3)
12
14
13
IC504(2/2)
5
4
3
9
1
7
IC500(3/3) IC300(2/2)
2
15 5
7
1
6
10
B-Y CLAMP OFFSET
3/4
TP302
Q507
10
1/4
Q306-308
G-Y MATRIX
BUFFER
5
7
6
1
2
TP501
Q510
5
1
3
9
G
IC305
B BUFFER
IC501(3/3)
5
4
3
IC304(2/3)
5
4
3
9
MATRIX AMP
Y BUFFER
9
TP500
Q503-505
11
2PB/2B
PB/B
IC101(3/3)
5
4
3
Q506
B-Y/B BUFFER
IN
ANALOG
B-Y/B
IC101(1/3) TP100
12
Q103-105
14
13
CLAMP
11
1-12b
1-12a
Y CLAMP OFFSET
BK (2/4)
B
C
D
SIGNAL INPUT SELECT
SIGNAL PROCESSING
BK BLOCK (2/4)
10-5
E
F
G
H
BK (3/4)
TP304
TP303
1
2/4
Q352-354
G
IC307
2
L. L
CONV
5
1/4
1/4
I/O
C
I/O
C
IC306
6
(1/2)
1 5
7
7 6
IC310(1/3)
12
14
13
B
I/O
C
L. L
CONV
5
I/O
C
IC510
(1/2)
5
7
6
6
1
7
FROM BC 1-17b
4
WHITE INSERT P
CHAR BLK
1-17b
1/4
CH BACK H/B
1/4
WB INSERT P-
I/O
C
L. L
CONV
5
1/4,2/4
B BUFFER
I/O
C
5
1
GCA
GAIN CONT
DC CONT
3
TP104
IC110(2/3)
2
15
1
IC106
6
(1/2)
1 5
7
7 6
Q570-572
IC512
11
R CLAMP
2
R SET UP
R 100 IRE
Q568
Q165
R BUFFER
9
10
IC110(1/3)
12
14
13
1/4
1/4
11
BLUE ONLY
BRT
Q166
R BRT
BUFFER
Q167-169
IC112
5
5
GCA
GAIN CONT
DC CONT
3
IC508
I/O
C
6
I/O
C
7
IC509
2
4
1
1/4
DRIVE REF
1/4
CH LEVEL
1/4
BIAS REF
2
3
1
2
3
1
2
3
1
R BUFFER
7
IC306(2/2)
IC506(2/2)
IC106(2/2)
R BUFFER
1/4
1/4
W/B P SW
AUTO C/P P SW
S PULSE
1-27a
9
1/4,2/4
FROM BC 1-18a
FROM BC 1-18b
FROM BC 1-19a
IC703(1/2,2/2)
5
7
6
5
FROM BC 1-27a
IC706(1/2)
3
4
5
11
W B INSERT P
CHAR G
CHAR B
CHAR R
1-18a
1-18b
1-19a
1/4
1/4
1/4
W & DP
BIAS P
CONT
1
2
1
2
1
2
4 IC331
6
5
GB SEL
R SEL
13
14
15
12
1
5
2
4
6
X 3
4/4
VIDEO COMP
1/4
IC514
(1/2,2/2)
2
1
3
6
5
IC116
X0
X1
X2
X3
X4
X5
X6
X7
7
X 3
OPEN
EN
A B C
11 10 9
IC114
(1/2,2/2)
2
1
3
6
5
7
IC702
IC702
(1/2)
(2/2)
1
15
13
14 2
12
10
11
IC701(1/3,2/3)
5
IC700
4 (1/2) IC707
3
6
7 2 D Q5
9
5
1 CK
13
14
3
12
Q
11
PULSE INSERT
SIGNAL PROCESS
BK BLOCK (3/4)
10-6
C
DR
OPEN
EN
A B C
11 10 9
IC700(2/2)
2
1
3
B
4/4
4 IC531
B BUFFER
1
1/4
1/4
A
DB
7
4 IC131
Q567
5V
3
2
4/4
IC314
(1/2,2/2)
2
1
3
IC516
X0
X1
X2
X3
X4
X5
X6
X7
IC113(2/3,3/3)
5
4
3
9
1
15
2
10
Q164
1/4,2/4,4/4 BLACK SAMPLING P
1/4,2/4,4/4 WHITE SAMPLING P
IC706(2/2)
13
14
12
DG
OPEN
EN
A B C
11 10 9
IC513(2/3,3/3)
5
4
3
9
1
15
2
10
Q569
B BRT
BUFFER
1
L. L
CONV
B BUFFER
7
13
14
15
12
1
5
2
4
6
IC110(3/3)
3
4
5
IC111(1/2,2/2)
IC113
6
(1/3)
7
12
5
14
13
3
1
2
11
1
2
X 3
10
Q142-144
IC107
IC316
X0
X1
X2
X3
X4
X5
X6
X7
IC313(2/3,3/3)
5
4
3
9
1
15
2
10
IC510 (1/3)
12
14
13
TP103
R
G BUFFER
7
Q376
G BRT
BUFFER
IC511(1/2,2/2)
IC513
6
(1/3)
7
12
5
14
13
3
1
2
11
B SET UP
B 100 IRE
1/4
1/4
10
TP504
IC510(2/3)
2
15
1
IC507
2
3
3
9
G BUFFER
B CLAMP
2
Q377-379
5
GCA
GAIN CONT
DC CONT
Q374
Q542-544
2/4
IC312
1
13
14
15
12
1
5
2
4
6
11
TP503
1/4
1/4
IC310(3/3)
3
4
5
IC311(1/2,2/2)
IC313
6
(1/3)
7
12
5
14
13
3
1
2
11
G SET UP
G 100 IRE
2/4
Q375
G BUFFER
IC310(2/3)
2
15
1
G CLAMP
BK (3/4)
D
10-6
E
F
G
H
BK (4/4)
Q400
3/4
1/4
1/4
DG
G BUFFER
TP305
Q380-382
G DRIVE
AMP
2
3
G DRIVE V
IC317(1/3)
12
IC318(1/2)
5 14
13
7
6
11Q384-386
IC315
8
G DRIVE
1 GCA 12
AMP
10
IC328(2/2)
1
IC323(1/2)
3
1
2
IC328(1/2)
6
7
5
G DRIVE IK
IC327(2/2)
5
7
6
IC326(2/3)
13
14
12
11
Q600
3/4
DB
B BUFFER
TP505
Q573-575
B DRIVE
AMP
8
1
10
IC515
GCA
2
3
3
9
1/4
1/4
B DRIVE V
IC528(1/2)
6
7
5
B DRIVE IK
IC527(2/2)
5
7
6
IC526(2/3)
13
14
12
11
Q200
3/4
1/4
1/4
DR
TP105
R BUFFER
Q170-172
R DRIVE
AMP
8
1
10
IC115
GCA
IC128(2/2)
2
1
3
R DRIVE V
IC128(1/2)
6
7
5
R DRIVE IK
1/4
IC518
(2/2)
IC517(3/3)
5
4
3
IC326(1/3)
3
5
9
IC321
IC326(3/3)
1
(2/2)
15 6
7
2
5
10
TP506
IC519
3
IC118
(2/2)
2
3
IC117(3/3)
5
4
3
1
IC521
IC526(3/3)
1
(2/2)
15 6
7
2
5
10
TP106
IC119
3
9
DIFF.
STAGE
7
9
11
DRIVE SAMPLING P
IK/V SW
VIDEO TIMING P
BIAS SAMPLING P
B
C
IC523
IC524
IC523 IC522
(1/2)
(3/3)
(1/2)
(2/2)
7 6
1 2
7 15
1
5
2 3
FROM
BK 5-1
507-1
RCV
KR
G1-3
KG
11
10
KB
DIFF.
STAGE
GM
G1-1
KB
G1-2
7
3
G4
1
G2
8
KR
G1
J501
13
H2
H1
6
5
2
4
7
9
5
FROM G
3-23a, b
FROM G
3-22a, b
508-8
508-7
H2
H1
3
FV2
FV1
120V TP107
KR
2-1
-5V
Q179
6
5
-5V
IC121
IC126(3/3)
1
(2/2)
15 6
7
2
5
10
4
IC123
IC124
IC123 IC122
(1/2)
(3/3)
(1/2)
(2/2)
7 6
1 2
7 15
1
5
2 3
10
IC121(1/2)
2
1
3
5
Q700-702
R.G.B
G2 CONTROL
IC705(1/2)
2
1
3
G2 CONTROL 1-10b
IC705(2/2)
6
7
5
G2 REF
RGB DRIVE OUT
RGB DRIVE IK/V CONTROL
BK BLOCK (4/4)
10-7
A
RV501
H STAT
12
KG
IC701
FROM P
(FBT)
T901
+5V
1/4,2/4,3/4 WHITE SAMPLING P
1/4,2/4,3/4 BLACK SAMPLING P
1/4,2/4,3/4 BIAS & DRIVE P
1/4
BIAS CLAMP P
1/4
504-1
10
Q177,178
TRANSIENT
OFF SW
IC124(2/3) IC122
(2/2)
13
14 2
1
12
3
11
IC126(1/3)
3
4
5
9
G2 CTRL
2
1
3
IC601(2/2)
+60V
+12V
Q601,602
5
G2
7
6
BUFFER
IC601(1/2)
9
IC521(1/2)
2
1
3
Q190
1/4
R DRIVE COMP
1/4
R BIAS IK
506-1
4-1
-5V
5
IC117(2/3)
2
15
1
10
IC129(2/2)
3
4 3
1
5
2
9
IC124(1/3)
KB
-5V
IC526(1/3)
3
5
9
508-1 H STAT CTRL
505-1
120V TP507
6
5
4
FROM
E 802-16b
(CRT SOCKET)
Q603
H STAT
OUT
2
+5V
B DRIVE COMP
1/4
1/4
B BIAS IK
C
Q582
IC524(2/3) IC522
(2/2)
13
14 2
1
12
3
11
R CUTOFF
IC126(2/3)
13
14
12
1/4
1/4
1/4
1/4
9
IC323
(1/2)
2
1
3
508-2
Q581,580
TRANSIENT
OFF SW
Q590
-5V
IC127(2/2)
5
7
6
7
IC324
IC323 IC322
(3/3)
(1/2)
(2/2)
7 6
1
7 15
5
2
10
TO P T901 (FBT)
IC321(1/2)
2
1
3
5
IC118 IC117(1/3)
(1/2)
12
5 14
13
7
6
11
Q174-176
R DRIVE
12
AMP
IC127(1/2)
3
1
2
DIFF.
STAGE
V901
PICTURE TUBE
HV
-5V
4
1
3-1
-5V
6
5
9
B CUTOFF
KG
Q389
IC324(2/3) IC322
(2/2)
13
14 2
1
12
3
11
1
IC517(2/3)
2
15
1
10
IC529(2/2)
3
4 3
1
5
2
9
IC524(2/3)
1/4
9
+5V
-5V
IC528(2/2)
2
IC527(1/2)
1
3
3
1
2
7
5
1/4
G DRIVE COMP
G BIAS IK
1/4
2
3
DIFF.
STAGE
120V TP307
Q387,388
TRANSIENT
OFF SW
Q390
IC317(2/3)
2
15
1
10
IC329(2/2)
3
4 3
1
5
2
9
IC324(1/3)
IC518 IC517(1/3)
(1/2)
12
5 14
13
7
6
11
Q577-579
B DRIVE
12
AMP
1
IC319
IC318(2/2)
-5V
G CUTOFF
1/4
TP306
IC317(3/3)
5
4
3
BK (4/4)
D
10-7
E
F
G
H
BC (1/2)
IC2
BACK-UP/RESET
6
V OUT
5
4
CS
BAT
2
BATS1
RESET
IC1 CPU
Q3
SIO RESET
SW
21
Q10
CC RESET
SW
D0-D7 25-32
33-40
A0-A18 43-53
14
RD
15
WR
RES
2/2
CC RESET
DATA BUS
D5V
FROM E
FROM BK
FROM BK
FROM E
1-B25
1-B24
1-A20
1-B20
1-B19
V BLANK 2
V BLANK 1
H SYNC
V SYNC
AFC
5
6
8
7
9
IC35
15
15
14
12
13
11
IC8(6/6)
13
12
57 FTI1
61
FTOB2
59
FTI3
1
2
2/2
2/2
2/2
H SYNC
V SYNC
AFC P
2
IC8(1/6)
IC121(1/6-3/6)
3
4
54
IRQ2
IRQ1
5
6
8
IRQ0
1
2
9
13
IC15(4/6-6/6)
12 11
10 9
8
IRQ5
IRQ1
IRQ0
1 XTAL
84
EXTAL
TB
3
SCK1
HD(1/2)
IC12(3/4)
9
8
10
1-B27
MISO
81
IC12(1/4)
5
6
4
IC12(2/4)
2
3
82
1
RXD1
3
SIO CLK
76
FTOA3
4
RD
WR
20
CE
22
OE
27
WR
IC13
ADDRESS SELECTOR
A5
1
Y0 15
A
14
2B
A6
3C
13
A7
Y2
4
12
Y3
D5V 5
11
EN Y4
6
10
9
7
Y7
TB
2-B23
RXD
RXD
102-8
2-A21
RXD
RXD
102-3
TP7
1-A28
MOSI
TP8
1-B28
TO BK,E
12
11
52
20
21
22
23
60
61
HD(2/2)
1
5
6
9
CN101(2/2)
CONTROL
TO BK,E
SCLK
CS0
CS1
CS2
+5V DRIVE
54
30-32
PA0
35-39
55
12V
2/2
D0-D7 PA1
PA1
Q7
56
46-48
A0-A2 PA2
2/2
PA2
+12V DRIVE
59
2/2
INT SIG EN
PA3
62
43
PA6
WR
Q5
Q4
44
PA7 63
RD
PC6 17
+12V SW
+5V SW
64,3-9
PB0-PB7
14
2/2
PC3
SDI CC
13
2/2
CC ON/OFF
18
45
CS
24,27,28
49
PEO PD4-6
Q9
29
PD7
TALLY DRIVE
4
A0-A4
WR,RD
2/2
2/2
CC C/T
CC L1/L2
SENSE
SAD DISP
SAD BLK DISP
SEL SYNC
SELECT SYNC SEP
SYNC ON/OFF
EXT INT SG EN
CS
2/2
CS
2/2
CHARA 3
CHARA 2
CHARA 1
2/2
2/2
2/2
TXD 1
SCLK 1
2/2
2/2
VITC DTSE
2/2
1
3
5
1
3
5
9
11
IC33
IC32
PD4 2-A14
PD6
2-B14
PD5
2-B15
2-B13
TALLY
1-A16
1-B16
1-A15
1-B15
1-A14
1-B14
1-A13
1-B13
1
SLOT-0
SLOT-1
SLOT-2
SLOT-3
SLOT-4
SLOT-5
SLOT-6
SLOT-7
CN3(2/2)
TXD
REMOTE 1
IN
1
9
6
CN4(2/2)
REMOTE 1
OUT
IC26(1/2)
RXD
Q8
MASTER/SLAVE
SWITCH
7
1
2
5
11 CS
25
RX CLK
9
TX CLK
3
RX DATA
CS2
6
1
DSR
RXD
CTS
CN6(1/2)
ISR
5
9
301-8
IC30
CLOCK DRIVER
OPTION TXD
TXD
IC23
27,28 ISR CONTROL
1,2,5-8
14
D0-D7 RX RDY
21
RESET
20
CLK
12
C/D
13
RD
10
WR
19
TX DATA
24
IC27(4/4) CS0 11 CS
DTR
13
12
23
17
RTS
CTS
22
DSR
IC28(3/4)
25
8
9
RX CLK
9
TX CLK
IC27(1/4)
3
RX DATA
8
9
5
YC(1/2)
CN302
(1/2)
OPTION
IRQ1
IC22
27,28 REM1 CONTROL
14
1,2,5-7
D0-D7 RX RDY
21 RESET
20 CLK TX DATA 19
12 C/D
13 RD
10 WR
2
1
CN4(1/2)
REMOTE 1
OUT
9
1
2-B19
IC31(1/6) IC31(6/6)
1
2 13
12
TB
12,13
D0 2-7
10
CLOCK
D7
4-1 IC19
15-12 D0-7
11-9
Y
4-1 IC20
15-12 D0-7
5
11-9
A0-2
Y
A0-2
5
4-1 IC21
15-12 D0-7
10,11
Y
D5V
IRQ2
6
IRQ0
IC25(1/2)
7
5
IC24
RS-232C CONTROL
5
27,28
6
1,2,5-8
14
D0-D7 RX RDY
21
TP6
RESET
IC36(2/3)
20
CLK
7
19 10
TX DATA
12
C/D
13
RD
IC36(3/3)
10
WR
14
23 11
RTS
CS1 11
CS
IC27(2/4)
10
7
TP5 25
IC36
RX CLK
IC27(3/4)
9
(1/3)
TX CLK
11
14
8
9
3
RX DATA
6
IC401
7 3
2
8
7
Q401-403
1 CURRENT
LIMITER
2-A22
+5V
+5V
B
C
+5V
301-7
CN302(1/2)
OPTION
2-B18
OPTION RXD
2-A17
OPTION RTS
RXD
301-6
RTS
301-3
TB
1
6
RTS
IC28(2/2)
7
10
CN6(2/2)
ISR
5
9
MAIN CPU
IN/OUT EXPANDER
REMOTE CONTROLLER
BC BLOCK (1/2)
BUAD SEL
10-8
A
TO HD 3-5
RY401
X2 4.9152MHz
2/2
YC(2/2)
9
2-A19
TXD
DTR
5
A0,1
NC
NC
TO/FROM E
TO/FROM BK
OPTION
OPTION
OPTION
OPTION
6
RXD
5
TXD
YA
8 IC34
SLOT DRIVER
1
5
201-1
201-2
201-3
TB
IC26(2/2)
3
6
4
9
OVER LOAD
STAND BY
POWER
OVER LOAD
STAND BY
POWER
+12V
1
2
3
4
5
6
11
12
2
4
6
8
10
TO BK,E
+5V
2/2
2/2
2/2
2/2
2/2
2/2
2/2
2/2
2/2
2
4
6
CN3(1/2)
REMOTE 1
IN
RESET
YB
IC25(2/2)
3
6
4
6
2/2
1-B26
D5V Q6
(14G1/20G1 only)
63
62
60
(4G1/20G1 only)
FROM BK,E
5
IC14(1/2) TP9
8
78
2
80
RXD2
7
TXD1
79
SCK2
2-A23
2-B20
TXD
TXD
TXD 102-7
TXD 102-2
6
3
77
28
VCC
10-3,25,24,
D0-D7
11-13
21,23,2,26,1
A0-A14 15-19
IC10
ADDRESS SELECTOR
IC9
(1/2)
15
1
A
14
1 8
2
B
7
3
2
13
C
Y2
4
12
Y3
D5V 5
11
EN
6
10
9
7
IC14(2/2)
TP10
TXD2
X1 20MHz
CN101(1/2)
CONTROL
A15
A16
A17
A18
Q2
IC6
I/O PROT EXPANDER
IC4
SRAM
IC3
PROGRAM ROM
1
VPP
12-5,27,26,23
D0-D7
13-15
4,28,29,3,2,30
A0-A17 17-21
IC125(6/6)
12 22
A18 13
CE
RD
24
OE
31
WR
WR
2/2
V BLANK 2
D0-D7
+5V
ADDRESS BUS
CONTROL BUS
A0
1
BC (1/2)
D
10-8
E
F
G
H
BC (2/2)
BC (2/2)
IC7
CHARACTER GEN
IC5
IN/OUT PROT EXPANDER
D0-D7
A0-A4
WR,RD
1/2
CS
6
1
CN5
REMOTE2
9
5
30-32
35-39
46-48
43
44
45
IC29
REMOTE2 DRIVER
2
18
3
17
4
16
5
15
6
14
7
13
8
12
11
9
D0-D7 PD0-PD7
A0-A2
WR
RD
CS
18
PC7
17
16
15
14
13
12
11
PC0
20-24
27-29
BUAD SEL
1/2
1/2
1/2
1/2
SCLK 1
TXD 1
PA 2
1/2
PA 1
Q1
9
OCS IN
19
V SYNC
20
H SYNC
V BLANK 2
AFC P
1/2
1/2
54-56,59
PA0-PA3
60,61
PA4,PA5
64,3-9
PB0-PB7
49,50,52,53
PE0-PE3
CLK
DATA
CS
PCL
OCS OUT
VR
VG
VB
VCBL
CHARA 3
DIGITAL +5V
DIGITAL +5V
+15V
+15V
+6V
+6V
–15V
–15V
1-A29
1-B29
1-A5
1-B5
1-A7
1-B7
1-A4
1-B4
+12V REG
+12V
OPEN
PA7
IC52
+5V REG
PA6
+5V
CHARA 2
1-B8
1-A9
1-B9
H SYNC
9
SEL SYNC
VP0
VP1
VP2
VP3
IC120 SYNC GEN
CLK
NTSC/PAL
MODE
SELECT
11
1
2
3
RESET
GEN
12
1
12
2
+5V
13
IC115(3/3)
X103
14.5MHz
IC114
4
A
3
VCO
5
B
9
8
IC63(3/3)
5
4 1
3
IC121(4/6)
1/2
V SYNC
10
1/2
SELECT SYNC SEP
1
2
4
Q
D5V
3
Q114
FROM BK
(NC)
IC62
4
Q51,52
SYNC
BUFFER
Q151,152
Y
BUFFER
1/2
1/2
1/2
1/2
1/2
+5V
1/2
1
2
EXT INT.SG.EN
INT. SG
1-B31
6
15
11
10
Q
Q
1/2
1/2
1/2
IC17(1/4-4/4)
9
8
10
12
11
13
5
6
4
2
3
1
4
12
13 IC111(3/3)
14
12
7
IC106 COUNTER
3
A
4
B
5 C
6 D RC 15
2
CK
5V 7
EP
10
LD
9
2
3
Q
Q
5
IC122(5/6) IC117(4/4)
13
11
11
10
12
9 IC122(1/6)
IC116(1/3)
12
14
13
15
Q2 26-24
Q2
IC104
LINE COUNTER
11-13
D0 15-19
D7
26
24
Q2
Q0
Q1
Q2
8
11
IC109
DAC
1-8 D0
20
IO
D7
21
IO
12
CLK
RV101
9
BLK
INT
16
SIGNAL
LEVEL
15
IC111(1/3) Q107
1
15
2
10
IC111(2/3)
5
4
3
Q108
MIX
AMP
11
Q116
525/526
SWITCH
IC113
12
9
D Q
11
CK
8
Q
IC124
CLOSED CAPTION
11
10 CHAR BLANK
3 11
BLK
1
2 CHAR R
2
1
5
R
17
CHAR G
8
9
6
G
18
6 CHAR B
8
7
5
B
IC63(1/3)
12
14
13
11
SDI CC
CC ON/OFF
CC RESET
CC C/T
CC L1/L2
IC117(3/4)
9
8
10
4
5
6
LPF
17
A4
A0
A1
A2
A3
DO 7
DO 6
DO 5
DO 4
DO 3
DO 2
DO 1
DO 0
WR
RD
CS
SENCE
VITC DTSE
1
OPEN
1-A19
CHAR R
TO BK
1-A18
CHAR G
TO BK
1-B18
CHAR B
TO BK
1-B17
CHAR BLANK
TO BK
1-A27 SAMPLE PULSE
TO BK
1-B10
Y/G
TO BK
1-B12
PR/R
TO BK
1-B11
PB/B
TO BK
7-A13
RCS 1
Q111
D104
BUFFER
Q112
D106
Q113
D107
3
IC110
P/S CONVERTER
14,12-10
5-2 A-H
IC122
13
QH
(3/6)
5
6 6
7
15
D7 19
9
D5V
D112
1/2
1/2
OPEN
CHAR BLANK
CHAR R
CHAR G
CHAR B
D113
IC125
(1/6-3/6,5/6)
1/2
1/2
SAD BLK DISP
SAD DISP
5
7-A16
7-A12
7-A18
Q115,D109
Y
BUFFER
CK IN
H SIN
525/526
OPEN
BC BLOCK (2/2)
10-9
B
4
SYNC ON/OFF
INT SG EN
IN/OUT EXPANDER
SYNC GNERATOR
A
2
9 IC151(1/3)
10
8
11
IC115(2/3) IC117(1/4,2/4)
4
D13
2
3
1
6
3
5
D111
2
5
D Q
3 CK
6
Q
Q109
5V
Q110
IC122(4/6)
11
CS
SENCE
VITC DTSE
Q106
9
IC107
INT SIGNAL DATA
D0 11
10-3
D1 12
25
D2 13
27
D3 15
21
D4 16
23
D5 17
2
9
7
6
5
4
10
CLK
3
2
13
12
Q10 14
11
9
4-10
25
3
24
21
23
2
26
27
Q1
6
9
2
IC108
INT SIGNAL DATA
13
LD
16
IC123
(1/2,2/2)
12
9
Q
11
8
Q
V SYNC SEL
7-A10
Y IN
OPEN
IC61(1/2)
Q 13
5
5V
Q103,104
IC116(2/3)
2
15
1
14
IC105
DOT CLOCK COUNTER
Q3 23-17
3-10 D0
Q9
D7
IC63(2/3)
IC119(2/3) IC122(6/6)
1
15 13
2
12 10
14 13
12
10
11
13
IC121
(5/6)
8
62
X102
14.1875MHz
(PAL)
IC116(3/3)
5
4
3
9
IC16(2/2)
Q 5
10
-5V
IC121
(6/6)
X101
14.3182MHz
(NTSC)
1/2
1/2
13
63
16 MODE
1/2
CHARA 1
IC51
-5V REG
VIDEO
P.Y OUT
P.C OUT
1/2
D+5V
IC37
4
IC16(1/2)
Q 13
2
9
FROM G
FROM G
FROM G
FROM G
FROM G
FROM G
FROM G
FROM G
3
IC11(1/2)
2
1
3
1
1/2
IC8(2/6-5/6)
12
CHAR B
CHAR G
CHAR R
CHAR BLANK
1/2
1/2
1/2
2
4
3
5
8
7-A9
7-A5
7-A6
7-A7
7-A8
7-B5
7-B6
7-B7
7-B8
7-B9
7-B10
7-B11
7-B12
7-B16
7-B17
7-B15
7-A15
7-A11
C
D
10-9
E
F
G
H
E (1/2)
E (1/2)
IC801(2/4)
8
9
10
1
801-6a
801-18b
+5V
FROM BC
FROM BC
FROM BC
CH SLOT 2
S CLK
MOSI
801-2b
801-5a
801-5b
2
IC801
(4/4)
3
2
1
IC801
(1/4)
5
6
4
IC801
(3/4)
12
11
13
3
FROM G
RESET
G PROT 4
G PROT 3
G PROT 2
G PROT 1
MOSI HV CTRL
PA6
20 RESET
IC611(1/2,2/2)
V BLK T 5
7
6
Q808,809
IC803
EEPROM
V BLK B 3
2
801-16a
801-16b
801-17a
801-17b
H STOP
V STOP
H +B
H BLK W
H BLK PH
18
19
2
3
4
5
6
7
8
9
12
13
3
IC628(6/6)
4
11
IC628(5/6)
10
IC602
2 (1/2)
6
Q
12
11
7
Q
9
1
IC628(1/6)
2
+5V
Q131-133
V STOP
DETECT
V STOP
2/2
IC301
30
27
26
28
29
24
23
18
17
19
20
7
6
9
10
13
14
2/2
2/2
D121
HV OFF
IC151
MUL
25
6
7
10
9
13
14
20
19
17
18
23
24
2/2
DFY
22
MUL
MUL
2/2
21
3
4
2
8
V SAW
2/2
DFX
8
8
MUL
Q151,152
H LIN
AMP
11
12
MUL
Q271,272
21
MUL
BUFFER
30
22
Q155-157
Q159
H LIN
AMP
IC202
IC204
(1/2)
2
(1/2) Q273
16
7
3
AMP
5
FROM BK
801-12a
801-12b
801-13a
801-13b
2/2
H PARA
15V
+B
Q061
H SIZE REG
SWITCHING
15
2
L062
14
12
3
H+B
2/2
3
4
1
2
12
IC641(1/2) IC641(2/2) +12V IC622 13
3
(2/2)
1
5
7
5
2
7
6
6
FROM G
DIGITAL +5V
DIGITAL +5V
+B
+B
+15V
+15V
+6V
+6V
–6V
–6V
–15V
–15V
801-4a
801-4b
801-31a
801-31b
801-28a
801-28b
801-26a
801-26b
801-27a
801-27b
801-29a
801-29b
D+5V
4
5
15
10 H DELAY
14
11 V DELAY
IC623(1/2)
6
3
5
6
PULSE
INTERFACE
7 6 H SEP
+5V
5
HD
9
40
41
V PARA
P OUT
31
29
DEF OSP
&
COUNT
PROC
H AFC
34
BUS
DEC
V SEP
IC628(2/6)
44
X001
LATCH
D/A
23
11
48
15
4
801-8b
H BLK P
TO BC
TO BK
TO G
801-24a
V SP
TO BK
16
14 15 8
T051
HDT
+B
14
10
Q
+5V
12
11
9
Q
13
IC623(2/2)
5
3
9
CY HP +
2/2
CY HP –
CV HP +
2/2
2/2
9 -6V
DY
Q054
TP052
H DRIVE
4
IC091(2/2)
3
1
2
Q622
2/2
V REF
H OUT
Q051,053
IC625
(2/2)
D102
IC101
H CENTER
5
1
4
2
3
Q071,072
9 PWM
DRIVE
CLAMP
+B
TO BC
TO G
V
REF
OSC
SCL
SDA
Q111
AFC P
AMP
7
1
2
3
IC031
5
Q112
AFC P
BUFFER
IC627(5/6)
11
10
007-3
007-4
007-1
007-2
007-6
007-5
801-14a
H DY RET
H DY RET
H DY
H DY
V DY
V DY RET
AFC P
TP031
801-9b
IC612(1/2)
1
HP
TO BC
TO BK
TO G
TO BC
TO BK
TO G
IC921
+12V REG
IC991
+9V REG
+9V IC961
+5V REG
IC981
D TIM
HV DRV
SDA
SCL
15K
FF
+12V
+5V
2/2
2/2
2/2
2/2
2/2
2/2
IC091
5 (1/2)
7
6
Q091
H SENT
BIAS
MICRO COMPUTER
H/V SIGNAL GENERATOR
DEFLECTION DRIVE
-5V IC941
-5V REG
-12V REG
-12V
E BLOCK (1/2)
10-10
A
13
IC001 H/V SIGNAL GENERATOR
Q641
5
V BLK P2
L064
HLC
11
10
1
2
IC625
(1/2)
IC628(3/6)
13
12
IC071 3
1
IC628
IC203(1/2) (4/6)
3
8
1 9
IC204(2/2) 2
2
3
1
T052 HOT
D101
16
SDA
SCL
V DELAY
H DELAY
CLAMP
IC627
(2/6,3/6)
1
2
801-8a
TP151
8
2 VS
2 HS
HS
VS
TO BK
TO G
4
12
MUL
IC621(1/2) IC621(2/2) +12V IC622
(1/2)
3
1
6
7
3
2
1
5
2
Q621
T151
HLT
5
11
2H TIM
+5V
V BLK P1
Q121,122
H STOP
DETECT
H STOP
V BLK B
V BLK T
V BLK W
V BLK PH
D122
4
801-9a
IC602
14 (2/2)
10
D131
V PARA
IK PROT
HV OVP
4
5
2/2
2/2
2/2
2/2
HV CTL
LD CV
L MOSI
L SCLK
30
60
61
37
38
2
Q815
2/2
TO G
TO G
11
Q611
33
42
43
5
9
1
D5V
3
IK PROT
HV OVP
35 H STOP
36 V STOP
39 +B PROT PA4 0
PA4 1
V DELAY
H DELAY
IC627(4/6)
9
8
1
2/2
PROT
IC205 DAC
17
VBP
DI
G PROT 4
16
CLK VBB
G PROT 3
VBP
G PROT 2
HBW
G PROT 1
HBP
DFTB
15
29
LDBK DFSI
MB 88346
DFCOR
X0 23 X801
HLG
20MHz
HLB
HMP
24
HCB
X1
801-18a
E PROT
801-19a POWER ON
Q807
801-7a
46
47
48
49
TO BC
TO G
IC613
Q804
E PROT
1
CS
6
2
SCK SO
5
SI
Q802
Q801
FROM BC
Q803
IC802
MICRO COMPUTER
54
RA44 64
15
SOLT ID MISO 2
45
51
L SCLK 52
L MOSI 53
1
S CLK
44
POWER ON
41
HV OCP
MISO
DEGAUSS
B
C
D
10-10
E
F
G
H
E (2/2)
E (2/2)
802-16b H STAT C
IC201
1/2
D TIM
1/2
1/2
SDA
SCL
1/2
1/2
15K
FF
IC231
11
10
17
D/A
CONV
Q201
21
1
2
14
13
V SAW
PARA
X2
3
BUS
DECODER
L PARA
X2
4
SWITCH
U PARA
X2
6
3
4
IC202(2/2)
AMP
9V
TP241
V SAW
V PARA
IC702
3
4
7
6
1
2
TP701
9
8
TP711
1
2
9
8
6
7
IC203(2/2)
TP231
LCC RET
LCC RET
LCC
LCC
20-3
20-1
LCC
802-26a
802-26b
NTC
NTC
18-1
NTC RETURN
1
LCC RTN
LANDING
CORRECTION
COIL
NTC
802-27a
802-27b
1/2
1/2
TO C
802-31a
802-31b
802-30a
802-30b
NTC RET
NTC RET
18-2
NTC
802-29a ROT RET
802-29b ROT RET
802-28a
ROT
802-28b
ROT
CY(V)
802-24a
802-24b
CY(V) 2
802-16b V BLANK
802-25a CY(V) RET
802-25b CY(V) RET
19-2
ROT RTN
ROTATION
COIL
19-1
ROTATION
17-3
CY(V)
17-4
CY(V)RTN
2
CY (V)
CY (H)
IC701
1/2
1/2
2H TIM
H PARA
2/2
2/2
2/2
L MOSI
L SCLK
LD CV
4 5
6 13
2
3
IC703 DAC
17
DI
RC
16
CLK
RT
15
LDCV RB
LC
LT
LB
RCC
18
19
2
3
4
5
6
BUFFER
CY(H) RET
CY(H) RET
802-22a
802-22b
CY(H)
CY(H)
17-2
CY(H)RTN
17-1
CY(H)
Q725-727,729
AMP
8
7
MUL
9
10
18
17
19
20
30
26
27
28
29
23
24
Q721,722
12
14
MUL
802-23a
802-23b
TP721
11
CY HP +
1/2
CY HP –
1/2
CV HP +
1/2
TA
3
21
MUL
Q552-554
HV DRIVE
AMP
Q555
HV OUT
SWITCHING
25
MUL
Q551
HV REG
SWITCHING
+B
22
TP551
903-1
D555
+600V RECT
TO C
G2 OUT
T901 FBT
902-1
902-2
FBT(H)
FBT(C)
FBT(H)
FBT(C)
902-1
902-2
1
HV
14
(BVM-20G1 only)
2
1/2
1/2
902-11 HV RTN(DC)
15
Q561
HV REG OCP
DETECT
HV DRV
PROT
TO PICTURE TUBE
13
902-1
HV RTN(AC)
4
IC503
15-1
15-11
HV RTN(AC)
HV RTN(DC)
HV RTN(AC) 802-21a
HV RTN(DC) 802-20a
D501
IC501(2/2)
5
7
6
4
13
3
1
9
OSC
6
PWM DRIVE
V
REF
HV PROT
15
2
FV1
Q501,502
2
1
+12V
IC502
DC REF
3
14
902-9
8
5
17
18
7
16
904-1
904-2
DF X
DF Y
FV2
11
1/2
HV OFF
15-5
IK PROT
ABL 1
802-19a
15-9
HV OVP
HV PROT
802-21b
1/2
V REF
1/2
DFY
3
2
ABL OUT
1/2
1/2
1/2
DFX DRIVE
ABL
IK PROT
902-4
902-5
D545 D502
DFY OUT
DFX
ABL 2
IK PROT
HV OVP
HV CTL
1
Q321,322
11
8
15-4
T301
DFT
905-1
905-2
DF Y
DF X
802-23b
ABL
P
5
1
5
IC501(1/2)
3
1
2
802-20b
TA
PWM CONTROL
DF CONTROL
TO BK
E BLOCK (2/2)
TA
10-11
A
TO C BOARD
CRT SOCKET GM
IC531(1/2,2/2)
5
D534
7
6
Q301-304
Q306,307
1/2
TO C BOARD
CRT SOCKET G4
B
C
D
10-11
E
F
G
H
G
G
Q901
DEG SWITCH
1
3-A15
DEGAUSS
3-A29
3-B29
DIGITAL +5V
DIGITAL +5V
3-A26
+5V SENSE
3-A5
3-B5
+15V
+15V
3-A7
3-B7
+ 6V
+ 6V
Q213
3-A6
3-B6
– 6V
– 6V
Q215
3-A4
3-B4
–15V
–15V
3-A23
3-B23
3-A22
3-B22
HT(–)
HT(–)
HT(+)
HT(+)
3-A2
3-B2
+120V
+120V
3-B14
POWER
3-B17
3-A17
3-A16
3-B16
G PORT 4
G PORT 3
G PORT 1
G PORT 2
3-B15
E PROT
Q207
Q902
TP201
+5V OUT
3
D204
T201
IC1
+15V
Q6
+15V REG
1
+20V
SWITCH
D6
DEGAUSS
COIL
THP1
Q1,2
2
AC SW OUT
AC SW OUT
RY1
2-5
2-1
KICK
D2
DC REF
T3
PFCT
S901
MAIN POWER
2-3
2-7
Q5
PROTECT
Q203,204
E1
9
E2
10
BUFFER
Q205
CONVERTER
OUT
6
3
Q101,103
RELAY
DRV
NEUTRAL
LIVE
+15V
D103
PFC OVP IND
Q105,106
PFC OFF
1-1
1-3
Q104
PFC OFF
F1
T4AH/250V
IC101(1/2)
5
7
6
+15V
PROTECTOR
Q107,110
D104
LATCH
PH803
+20V Q206
4
3
Q108
RESET
Q214
-16V RECT
-16V SWITCH
PH901
D105
TP207
1
IC203
2 +16V REG
3
1
3
1
2
IC804
+6V OVP
2
4
3
SWITCH
D102
+15V IC101(2/2)
3
1
2
-6V SWITCH
D209
RESET
1
Q816
2
Q802
IC801(2/4)
6
1
+5V OVP
7
Q801
D810
Q904
D210
D812
BUFFER
Q102
IC801(3/4)
4
2
5
T301
D303
4
13
IC31 PFC CONTROL
4
10
9
OSC
16
PFC OUT
X2
A
AB
B 1M=
C
C
Q303,304
ERRER
AMP
3
5
V REF
11
6
8
GATE
16
E1
9
E2
10
BUFFER
Q305
CONVERTER
OUT
6.5V RECT
TP301 TP302
5
12
11
IC301 PWM CTRL
Q31
10
D304
+120V
RECT
7
TP303
TP306
+15V
PH301
1
4
3
2
4
D300
SWITCH
Q306
TP304
IC302
+120V REG
3
1
2
Q300,301
PH802
4
3
TP305
1
2
SWITCH
Q812 Q813 Q815
Q814
D806
PROTECT
Q805
D807
Q809
Q810
Q806,807
Q811
Q808
D+5V
5
IC801
(1/4)
D803
D804
10
11
2
IC801(4/4)
8
14
9
3
RLA DET
3
1
Q817
D305
VPFC
IC32
(1/2)
Q32
6
7
GAIN
5
CONT
IC802
REFERENCE
D811
Q109
+12V
(SEC)
Q212
-7V RECT
10
+15V
PH201
1
4
3
2
Q8,9
+12V REG
4
Q7
AC IN
100-240V
50/60Hz
Q211
D208
7
PROTECT
T1,2
LINE
FILTER
Q903 IC901
+7V RECT
12
11
ERRER
AMP
Q210
Q209
+16V
DRIVE
+6V SWITCH
D207
3
5
D4
PROT IND
+16V RECT
4
13
IC201 PWM CTRL
16
3
14
VPFC
D36
RECT
D5
Q4
AC SW IN
AC SW IN
TP31
D9
D1
MAIM
RECT
IC202
Q208 +5V REG
D206
D203
20V RECT
1
+16V SWITCH
2
15
RY901
+7V RECT
D205
D+5V IND
IC803
ENCODER
11
12
9
13
1
7
6
2
14
3
4
5
13
D801
PFC IND
MAIN RECT
±6V REG, ±15V REG, +B REG, D5V REG
10-12
A
B
C
D
G BLOCK
10-12
E
F
G
H
HA, HB, HC, HD
HA, HB, HC, HD
HD (RELAY)
6
IC13
1
102-2
102-7
102-3
102-8
102-5
(BVM-14G1/20G1 SERIES) TO MONITOR
9
TXD
TXD
RXD
RXD
+5V
5
RXD
RXD
TXD
2-8
2-3
2-7
TXD
+5V
2-2
2-5
RXD1
TP4
28
TXD1
3
6
(BVM-14G5 SERIES)
TO TB BOARD
CN8
5V REG
6
A0-A7 56-49
IC202
SERIAL-PARALLEL
CONVERTER
13 DATA
SQ 12
11-7,5-3
14
CLK
15
STB
16
CLR
TP204
MOSI
SCLK
CE2
201-4
201-3
201-6
5V
IC3
S201-214
Q201
A3 1
A4 2
A5 3
5V
RES
S215-222
D223-226
Q202,203
201-5
MISO
X1
20MHz
10
XTAL
EXTAL
TMRI0
S232
BRIGHT
S233
CHROMA
EN3 A
EN3 B
EN2 A
EN2 B
EN1 A
EN1 B
EN0 A
EN0 B
ENCODER 3
ENCODER 3
ENCODER 2
ENCODER 2
ENCODER 1
ENCODER 1
ENCODER 0
ENCODER 0
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3A
3B
2A
2B
1A
1B
0A
0B
19
TP5
25
TXD0
27
SCK0
IC11
EDGE TRIG F/F
2 D1
Q1 19
3 D2
Q2 18
4 D3
Q3 17
5 D4
Q4 16
6 D5
Q5 15
7 D6
Q6 14
8
D7
Q7 13
9 D8
Q8 12
11
EN
1
10
Q103
IC9
MISO
IC101
SERIAL-PARALLEL
CONVERTER
13 DATA
11-7,5
14
CLK
P1-P6
15
STB
16
CLR
2A 1
3B 3
3A 5
2B 9
1A 11
1B 13
2
4
6
8
10
12
P9-P14
IC10
0B 3
0A 5
D121-126
2,1,23-20
19
P15
P16 17
4
6
S101-106
MISO
5-5
MISO
4-5
CE1
MOSI
SCLK
4-6
4-4
4-3
SCLK
MOSI
CE2
5-3
5-4
5-6
EN
15
14
13
IC14
12 TP8
RD 12
13
11
11
10
9
WR 9
10
7
8
IC14
5V
IC10
9
8
1
2
18
17
16
15
14
13
12
11
2
3
4
5
6
7
8
9
WR
RD
TP9
IC10
1
19
5V SWITCH
(MEMORY CARD)
VPP 5V
DATA BUS D0-D7
2
4
6
8
11
13
15
17
18
16
14
12
9
7
5
3
2
MEMORY
CARD
IC21
1
2
4
5
5V 10
9
13
12
3
6
8
11
IC7
EDGE TRIG F/E
2 D1
Q1 19
3 D2
Q2 18
4 D3
Q3 17
5 D4
Q4 16
6 D5
Q5 15
7 D6
Q6 14
8
Q7 13
D7
9 D8
Q8 12
11
EN
1
1-15
1-9
1-7
1-42
1-58
1-61
WE/PGM
OE
CE1
CE2
RESET
REG
1-16
1-33
1-67
1-63
1-62
1-59
1-36
RDY/BSY
WP
CD2
BVD1
BVD2
WAIT
CD1
1-30
1-31
1-32
1-2
1-3
1-4
1-5
1-6
D0
D1
D2
D3
D4
D5
D6
D7
18
17
16
15
14
13
12
11
4
DIR G
1
19
RD
11
IC4
IC10
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
5
DIR G
19
RD 1
HB (FUNCTION SELECT)
HC (SYSTEM CONTROL)
FUNCTION SELECT
SYSTEM CONTROL, RELAY
10-13
A
B
C
D
10-13
E
3
IC8
2
3
4
5
6
7
8
9
Q101,102
LED DRIVE
19
IC6
ENA ENB
19
1
20
TMCI1
21
TMO1
26
RXD0
101-5
1
POWER CTRL
S234
PHASE
SWITCH OUT
IC14
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
1-29
1-28
1-27
1-26
1-25
1-24
1-23
1-22
1-12
1-11
1-8
1-10
1-21
1-13
1-14
1-20
1-19
1-46
1-47
1-48
1-49
IC12
LED DRIVE
IC102
SERIAL-PARALLEL
S107-110
CONVERTER
13 DATA P1-P4 11-8
14
CLK
15
D127-130
STB
16
CLR
1,2,23,22
P9-P12
12
SO
1
Q4
22
TMRI1 57-64
D0-D7
D111
5V
A6 4
5
A7 6
Q2,6
202-10
202-9
202-8
202-7
202-6
202-5
202-4
202-3
4 3
2
TP6 TP7
A YO
B
C
WAIT 38
37
RD
36
WR
S231
CONTRAST
HA (FUNCTION SELECT)
101-4
101-3
101-6
9
SWITCH OUT
2,1,23,22
MOSI
SCLK
CE1
8
IOS 34
D231
P15 19
P16 17
RESET
2
A8-A13
A14 6
5
13
IC10 IC14
5V
IC2
IC201
SERIAL-PARALLEL
TP202 TP203 CONVERTER
13 DATA
14
CLK
5V
15
STB
16
11-7,5-1
CLR
23-20
P1-P14
ADDRESS BUS A8-A15
A15
18
17
16
15
14
13
12
11
A7 2
A6 3
A5 4
A4 5
A3 6
A2 7
A1 8
A0 9
ADDRESS BUS A0-A7
A8-A15 47-40
5V
1
1
IC5
MICROCOMPUTER
IC16
2
IC1
TP3
2 29
7
8
5
HA, HB, HC, HD BLOCK
F
G
H
SECTION 11
DIAGRAMS
r For Printed Wiring Boards
11-1. PRINTED WIRING BOARDS
: Pattern from the side which enables seeing.
Board
Function
BK
R.G.B In Selector, R.G.B Gain Control,
Y/G. B–Y/B. R–Y/R Signal Processing, R.G.B Drive Out,
Contrast/Bright/G2 Control, Pulse Generator,
R.G.B Drive IK/V Control, System Control,
D/A Converter, Y/C Clamp Pulse Gen. ................................... 11-2
Micro Computer, Program ROM, S/Video RAM, Character Gen.,
Address Selector, Parallel In/Out, Serial Controller,
RS485/RS232C Interface, Signal/Character Generator,
D/A Converter, Closed Caption Display, Current Limitter,
Slot Receiver ........................................................................... 11-4
System Control, EEP ROM, H BLK/V BLK Pulse Gen.,
H/V Sync Gen., PWM Control, HV Reg./HV Out Switching,
Dynamic Focus, ROT. NTC. LCC. CY Out, D/A Converter .. 11-6
PFC Control, Main Rect, Converter Out, PWM Control,
D+5V, ±6V, ±15V, +120V, HT Rect ........................................ 11-8
R.G.B Out, BLK Out, H.STAT Out ........................................ 11-10
Relay (BVM-14G1/20G1) ...................................................... 11-10
FBT ......................................................................................... 11-10
Tally ......................................................................................... 11-10
Indicator .................................................................................. 11-10
Relay ....................................................................................... 11-10
Function Control (BVM-14G5, BKM-10R) ........................... 11-11
Function Control (BVM-14G5, BKM-10R) ........................... 11-11
CPU, Memory Card Driver, RS422 Driver,
Card Address Decoder (BVM-14G5, BKM-10R) .................. 11-12
Mother ..................................................................................... 11-13
Mother ..................................................................................... 11-14
BC
E
G
C
HD
P
YA
YB
YC
HA
HB
HC
TA
TB
Page
• Chip IC
:
1
• Chip transistor
C
:
B E
4 5 6
:
3 2 1
• Chip diode
3
:
2 1
:
11-1
11-1
K
A
n
BK
1
-BK
-1-667-740-11
D11
D12
D13
D14
D102
D103
D164
D165
D166
D167
D168
D200
D201
D302
D303
D374
D375
D376
D377
D378
D400
D401
D502
D503
D567
D568
D569
D570
D571
D600
D601
D701
D802
D803
D804
D900
D901
D902
D903
D905
IC1
IC2
IC3
IC101
IC102
IC104
IC106
IC107
IC110
IC111
IC112
IC113
IC114
IC115
IC116
IC117
IC118
IC119
IC121
IC122
IC123
IC124
IC126
IC127
IC128
IC129
IC131
IC300
IC301
IC302
IC303
IC304
IC305
IC306
IC307
IC310
IC311
IC312
IC313
IC314
IC315
IC316
IC317
IC318
IC319
IC320
IC321
IC322
IC323
IC324
F-7
F-7
* F-1
F-7
A-1
D-7
* A-5
A-2
A-3
* A-5
* A-5
A-4
* A-4
C-1
D-7
* C-5
C-2
C-3
* C-5
* B-5
C-4
B-4
B-1
D-7
* D-5
D-2
D-3
* D-5
* D-5
D-4
D-4
G-4
G-2
* G-5
* F-4
* G-1
* F-4
* F-4
* F-4
G-4
A-7
B-7
C-7
B-6
A-6
A-6
A-5
A-5
A-5
A-5
A-4
B-4
B-4
A-4
B-4
A-3
B-3
B-3
A-2
A-2
A-2
B-2
A-2
A-2
A-2
B-2
B-5
C-6
C-6
C-6
C-6
C-6
C-6
B-5
C-5
C-4
C-4
B-4
C-4
C-4
C-4
C-4
C-3
C-3
C-3
C-6
B-2
C-2
C-2
C-2
IC325
IC326
IC327
IC328
IC329
IC331
IC500
IC501
IC502
IC503
IC504
IC506
IC507
IC508
IC509
IC510
IC511
IC512
IC513
IC514
IC515
IC516
IC517
IC518
IC519
IC520
IC521
IC522
IC523
IC524
IC525
IC526
IC527
IC528
IC529
IC531
IC700
IC701
IC702
IC703
IC704
IC705
IC706
IC707
IC710
IC711
IC728
IC730
IC731
IC732
IC734
IC735
IC736
IC800
IC801
IC802
IC803
IC804
IC805
IC900
IC901
IC902
IC903
IC904
IC906
IC907
IC908
IC909
IC910
IC911
IC912
B-6
B-2
C-2
C-2
C-2
C-5
D-6
E-6
D-6
D-6
D-6
D-5
D-5
D-5
D-5
D-4
D-4
D-4
D-4
E-4
D-4
E-4
D-3
D-3
D-3
E-6
D-2
D-2
D-2
D-2
E-6
D-2
D-2
D-2
D-2
E-5
F-4
F-4
F-5
G-4
G-4
G-4
G-5
F-5
F-1
F-1
F-1
F-1
F-1
F-1
F-1
F-1
E-1
F-2
F-3
G-3
G-3
F-3
F-3
* F-2
F-4
F-6
G-6
G-4
E-5
B-2
B-5
C-2
C-5
E-2
F-6
Q100
Q101
Q102
Q103
Q104
Q105
Q106
Q107
Q108
Q140
Q141
Q142
Q143
Q144
Q164
Q165
Q166
Q167
Q168
A-1
A-1
D-7
* B-1
* B-1
* A-1
* B-2
* C-2
* B-2
A-6
A-6
A-5
A-5
A-5
* A-3
A-4
A-4
* A-4
A-4
Q169
Q170
Q171
Q172
Q174
Q175
Q176
Q177
Q178
Q190
Q200
Q300
Q301
Q302
Q303
Q304
Q305
Q306
Q307
Q308
Q309
Q310
Q350
Q351
Q352
Q353
Q354
Q374
Q375
Q376
Q377
Q378
Q379
Q380
Q381
Q382
Q384
Q385
Q386
Q387
Q388
Q390
Q400
Q500
Q501
Q502
Q503
Q504
Q505
Q506
Q507
Q510
Q540
Q541
Q542
Q543
Q544
Q567
Q568
Q569
Q570
Q571
Q572
Q573
Q574
Q575
Q577
Q578
Q579
Q580
Q581
Q590
Q600
Q700
Q701
Q702
Q705
Q706
Q800
Q801
Q802
Q803
Q804
Q805
Q806
Q807
Q808
Q809
Q810
Q811
Q812
A-4
A-3
A-4
A-4
A-4
A-3
* A-4
A-3
A-3
B-2
B-4
C-1
C-1
D-7
* C-1
* C-1
* C-1
* C-2
* C-2
* C-2
* C-2
C-6
B-6
B-6
C-5
C-5
C-5
* B-3
B-4
C-4
* C-4
C-4
C-4
B-3
B-4
B-4
C-4
C-3
* C-4
B-3
B-3
C-2
C-4
B-1
B-1
D-7
* E-1
* E-1
* D-1
* D-2
* D-1
D-6
D-6
D-6
D-5
D-5
D-5
* D-3
D-4
D-4
* D-4
D-4
D-4
D-3
D-4
D-4
D-4
D-3
* D-4
D-3
D-3
E-2
D-3
* B-5
* C-5
* E-5
G-4
G-4
* E-1
D-1
F-2
F-2
F-2
F-2
F-2
* F-6
F-2
G-2
G-2
F-2
* G-5
Q813
Q814
Q815
Q816
Q817
Q818
Q819
Q820
Q821
Q822
Q823
Q824
Q825
Q826
Q827
Q828
Q829
Q900
Q902
TP1
TP100
TP101
TP102
TP103
TP104
TP105
TP106
TP107
TP300
TP301
TP302
TP303
TP304
TP305
TP306
TP307
TP500
TP501
TP502
TP503
TP504
TP505
TP506
TP507
TP700
TP800
TP801
TP802
TP803
TP900
TP901
* F-5
* G-5
* F-5
* G-5
F-2
G-3
G-3
* G-4
G-3
* F-5
* F-5
* G-5
* G-5
* F-4
* F-5
F-3
* G-5
F-7
F-6
C-5
B-6
B-5
B-6
A-5
A-5
A-4
B-3
A-2
C-6
C-6
C-6
C-5
B-5
C-4
C-3
C-2
E-6
E-6
D-5
D-5
D-5
D-4
D-3
D-2
F-4
F-2
G-3
F-3
F-3
F-4
F-3
2
BK
3
4
5
6
7
A
B
C
D
*:B SIDE MOUNT
E
F
G
BK
–A SIDE–
1-667-740-11
11-2
11-2
BK
1
2
3
4
5
BK
6
7
A
B
C
D
E
F
G
BK –B SIDE–
1-667-740-11
11-3
11-3
BC
1
-BC
-1-668-433-11
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D21
D22
D23
D24
D29
D30
D31
D32
D33
D34
D35
D36
D37
D38
D39
D40
D41
D103
D104
D105
D106
D107
D108
D109
D111
D112
D113
D114
D115
D401
D402
D403
D550
D551
D552
D553
D554
D555
D556
D557
D558
D559
D560
D561
* B-1
* B-1
* B-1
* B-1
* B-1
B-7
B-7
B-7
B-7
B-7
B-7
* B-1
* E-2
C-7
C-7
C-7
C-7
* A-7
* A-7
* A-7
* A-7
* A-7
* D-7
* D-7
* E-7
* D-7
* E-7
* E-7
* E-7
* E-7
* E-2
* E-1
* E-2
* E-1
* E-1
* E-2
* E-1
* F-2
* F-2
* F-2
* B-2
* C-1
* A-4
* A-4
* G-1
* F-7
* F-6
* F-7
* F-6
* F-7
* F-6
* F-7
* F-6
* F-7
* F-6
* F-7
* F-6
IC1
IC2
IC3
IC4
IC5
IC6
IC7
IC8
IC9
IC10
IC11
IC12
IC13
IC14
IC15
IC16
IC17
IC19
IC20
IC21
IC22
IC23
IC24
IC25
IC26
IC27
IC28
IC29
IC30
IC31
IC32
IC33
IC34
F-4
E-3
E-4
D-4
D-2
E-5
F-5
F-5
D-4
F-5
F-5
G-5
F-5
C-6
G-4
G-5
G-5
F-3
G-3
F-3
B-2
C-2
B-2
A-2
A-2
F-2
F-2
E-1
F-2
F-2
E-6
E-6
E-6
IC35
IC36
IC37
IC51
IC52
IC61
IC62
IC63
IC104
IC105
IC106
IC107
IC108
IC109
IC110
IC111
IC113
IC114
IC115
IC116
IC117
IC119
IC120
IC121
IC122
IC123
IC124
IC125
IC401
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Q10
Q51
Q52
Q103
Q104
Q106
Q107
Q108
Q109
Q110
Q111
Q112
Q113
Q114
Q115
Q116
Q151
Q152
Q401
Q402
Q403
F-6
B-6
D-6
C-7
D-7
A-3
B-3
B-2
B-4
B-4
C-4
B-5
A-5
B-6
A-6
C-5
C-4
B-2
B-4
B-3
C-5
B-3
B-3
C-2
C-3
C-3
C-6
F-5
A-4
F-6
F-6
* E-5
D-6
D-5
D-6
D-6
A-2
A-7
* E-5
* B-5
* B-5
* C-3
* C-4
* B-2
* B-2
* B-2
B-6
* E-2
* E-1
* E-1
* E-1
* E-2
* E-1
D-4
E-6
* E-1
A-4
A-4
A-4
RV101
A-6
TP1
TP3
TP5
TP6
TP7
TP8
TP9
TP10
TP11
TP12
TP13
A-1
G-1
C-6
C-6
G-6
G-6
C-6
C-6
D-1
G-6
C-5
*:B SIDE MOUNT
2
BC
3
4
5
6
7
A
B
C
D
E
F
G
BC –A SIDE–
1-668-433-11
11-4
11-4
BC
1
2
3
4
5
BC
6
7
A
B
C
D
E
F
G
BC –B SIDE–
1-668-433-11
11-5
11-5
E
1
-E
-1-667-742-11
D031
D061
D062
D101
D102
D103
D111
D112
D113
D121
D122
D131
D151
D152
D153
D154
D201
D271
D301
D321
D322
D501
D502
D531
D532
D533
D534
D542
D543
D544
D545
D551
D552
D553
D554
D555
D611
D641
D642
♦ D721
♦ D722
D801
D802
D853
IC001
IC031
IC071
IC091
IC101
IC151
IC201
IC202
IC203
IC204
IC205
IC231
IC301
IC501
IC502
IC503
IC531
IC602
IC611
IC612
IC613
IC621
IC622
IC623
IC625
IC627
IC628
IC641
♦ IC701
♦ IC702
♦ IC703
IC801
IC802
IC803
IC921
IC941
IC961
IC981
IC991
Q051
Q053
Q054
Q061
Q071
Q072
C-7
* G-4
F-4
D-4
D-4
* D-4
* E-5
E-2
E-2
F-2
* F-5
F-2
* F-1
* F-1
* F-1
* F-1
* C-4
C-4
* B-4
* A-3
* A-3
* B-6
* F-5
* B-5
* B-5
B-3
* B-5
* B-5
B-2
* B-5
* B-5
* B-1
C-6
B-6
* A-1
A-6
* E-6
* E-5
* E-5
E-4
E-4
G-1
* F-6
E-1
C-2
C-7
G-3
C-1
D-3
C-3
B-2
B-3
C-3
C-4
C-3
A-2
C-4
B-2
B-3
A-3
B-2
F-2
F-3
F-3
E-2
E-3
E-2
E-2
E-2
F-1
E-1
E-3
C-5
A-2
C-5
G-1
F-2
F-1
D-2
D-1
D-3
D-3
B-2
* D-2
D-6
E-7
G-4
* F-4
* F-4
Q091
Q111
Q112
Q121
Q122
Q131
Q132
Q133
Q151
Q152
Q155
Q156
Q157
Q159
Q201
Q271
Q272
Q273
Q301
Q302
Q303
Q304
Q306
Q307
Q321
Q322
Q501
Q502
Q551
Q552
Q553
Q554
Q555
Q561
Q611
Q621
Q622
Q641
♦ Q721
♦ Q722
♦ Q725
♦ Q726
♦ Q727
♦ Q729
Q801
Q802
Q803
Q804
Q807
Q808
Q809
Q815
TP031
TP052
TP151
TP231
TP241
TP551
♦ TP701
♦ TP711
♦ TP721
C-2
* E-5
E-2
* F-4
* F-4
* C-2
* C-2
* C-2
* F-2
* F-2
G-6
F-7
F-7
F-7
* C-4
B-3
B-3
C-4
* B-4
* B-4
* B-4
* A-4
A-4
B-4
A-5
A-4
* C-1
* C-1
B-7
* C-2
* C-1
* C-1
A-7
C-5
* E-5
E-3
* C-5
E-3
* E-4
* F-4
F-4
E-4
E-3
F-3
F-1
* F-5
* F-6
* E-6
* F-5
* F-5
* F-5
* G-5
C-6
E-6
F-6
A-1
A-1
A-6
A-1
A-1
B-1
E
2
3
4
5
6
7
A
B
C
D
E
♦:BVM-20G1 only
*:B SIDE MOUNT
F
G
E –A SIDE–
1-667-742-11
11-6
11-6
E
1
2
3
4
5
E
6
7
A
B
C
D
E
F
G
E –B SIDE–
1-667-742-11
11-7
11-7
G
1
-G
-1-667-741-11
D1
D2
D3
D4
D5
D6
D8
D9
D31
D32
D33
D34
D35
D36
D101
D102
D103
D104
D105
D106
D202
D203
D204
D205
D206
D207
D208
D209
D210
D211
D212
D300
D302
D303
D304
D305
D306
D307
D801
D803
D804
D806
D807
D810
D811
D812
D901
E-3
D-3
D-3
D-4
D-2
D-2
* D-6
D-2
E-2
* E-5
E-2
E-2
D-1
C-1
E-2
* E-6
E-1
* E-6
* F-7
D-1
C-3
D-4
D-5
G-5
D-7
C-7
C-7
B-7
* B-6
* B-6
B-1
* A-6
A-3
B-7
A-7
* A-6
* B-5
A-1
G-6
* F-1
* F-1
* F-3
* F-3
* E-3
* G-2
* E-2
E-5
IC1
IC31
IC32
IC101
IC201
IC202
IC203
IC301
IC302
IC801
IC802
IC803
IC804
IC901
D-1
E-2
* E-6
* E-6
* B-5
G-5
E-5
* A-5
B-6
* F-2
F-6
* F-2
E-5
F-6
Q1
Q2
Q4
Q5
Q6
Q7
Q8
Q9
Q31
Q32
Q101
Q102
Q103
Q104
Q105
Q106
Q107
Q108
Q109
Q110
Q203
Q204
Q205
Q206
Q207
Q208
Q209
Q210
C-3
C-3
D-3
C-3
D-2
* D-4
C-4
* D-4
C-1
* E-7
E-1
* E-6
* E-6
* E-6
* E-6
* E-6
* E-7
* E-7
* E-7
* E-6
* B-5
* B-5
B-1
* D-3
G-4
E-6
* F-2
F-6
Q211
Q212
Q213
Q214
Q215
Q300
Q301
Q303
Q304
Q305
Q306
Q801
Q802
Q805
Q806
Q807
Q808
Q809
Q810
Q811
Q812
Q813
Q814
Q815
Q816
Q817
Q901
Q902
Q903
Q904
* E-2
D-6
* D-1
D-6
* D-2
* A-6
* B-6
* A-5
* A-5
A-1
* D-3
* G-2
* E-2
* F-3
* F-3
* F-3
* F-3
* F-3
* F-3
* F-3
* F-3
* F-3
* F-3
* F-3
* E-2
* E-2
E-5
* D-3
* F-1
* E-3
PH201
PH301
PH802
PH803
PH901
B-5
A-4
D-5
D-5
D-5
TP31
TP32
TP33
TP201
TP202
TP207
TP301
TP302
TP303
TP304
TP305
TP307
TP308
C-2
E-1
F-1
G-6
G-6
E-5
F-6
F-7
B-6
A-6
B-6
B-5
A-2
2
G
3
4
5
6
7
A
B
C
D
*:B SIDE MOUNT
E
F
G
G –A SIDE–
1-667-741-11
11-8
11-8
G
1
2
3
4
5
G
6
7
A
B
C
D
E
F
G
G –B SIDE–
1-667-741-11
11-9
11-9
C, BVM-14G1/20G1, BKM-10R HD
P, YA, YB, YC
HD –B SIDE–
1-657-342-11
BVM-14G1/20G1,
BKM-10R
P –B SIDE–
1-667-734-11
C –B SIDE–
1-667-733-11
YA –B SIDE–
1-667-735-11
11-10
11-10
YB –B SIDE–
YC –B SIDE–
1-667-736-11
1-667-737-11
BVM-14G5, BKM-10R
HA, HB
HA, HB BVM-14G5, BKM-10R
HA –A SIDE–
1-657-339-12
BVM-14G5, BKM-10R
HA –B SIDE–
1-657-339-12
BVM-14G5, BKM-10R
HB –A SIDE–
1-657-340-12
BVM-14G5, BKM-10R
HB –B SIDE–
1-657-340-12
BVM-14G5, BKM-10R
11-11
11-11
BVM-14G5, BKM-10R
1
-HC
-1-657-341-14
D1
D2
D3
D4
D5
D6
D7
D8
* A-1
* A-1
* A-1
A-5
A-5
* A-2
* A-3
* B-1
IC1
IC2
IC3
IC4
IC5
IC6
IC7
IC8
IC9
IC10
IC11
IC12
IC13
IC14
IC16
IC21
B-4
* B-1
C-3
* B-5
* B-5
* B-4
* B-4
* B-5
B-5
C-5
C-5
A-4
A-5
C-3
A-5
* B-5
Q2
Q4
Q6
A-3
A-3
A-3
TP1
TP2
TP3
TP4
TP5
TP6
TP7
TP8
TP9
A-1
B-5
A-5
A-4
A-4
C-5
C-3
C-3
C-3
HC
HC BVM-14G5, BKM-10R
2
3
4
5
A
B
C
HC –A SIDE–
1-657-341-14
BVM-14G5, BKM-10R
1
2
3
4
5
A
B
C
HC –B SIDE–
1-657-341-14
BVM-14G5, BKM-10R
11-12
11-12
TA
TA –A SIDE–
TA –B SIDE–
1-667-738-12
1-667-738-12
11-13
TA
11-13
TB
TB
TB –A SIDE–
TB –B SIDE–
1-667-739-12
1-667-739-12
11-14
11-14
Note:
11-2. SCHEMATIC DIAGRAMS
Board
Function
FRAME (1/3)
FRAME (2/3)
FRAME (3/3)
BK (1/9)
BK (2/9)
— ............................................................................................. 11-17
— ............................................................................................. 11-18
— ............................................................................................. 11-19
Signal Selector, R.G.B Gain Control ...................................... 11-20
G–Y Matrix, Y. PB/PR Mix, Signal Processor,
Blue Only SW ......................................................................... 11-21
R.G.B Signal Processing, R.G.B Drive ................................... 11-22
R Drive Out, R Drive IK/V Control ........................................ 11-23
G Drive Out, G Drive IK/V Control ....................................... 11-24
B Drive Out, B Drive IK/V Control ........................................ 11-25
Pulse Generator, G2. BRT. CONTR Control .......................... 11-26
H/V Sync Separator, Y/C Clamp P Generator ......................... 11-27
System Control, D/A Converter .............................................. 11-28
Micro Computer, Program ROM, S-RAM, Address Selector,
Parallel In/Out, Chracter Gen. ................................................. 11-31
Serial Control, RS485/RS232C Interface ............................... 11-32
Signal Generator, Internal Signal Data, Counter,
Closed Caption Display, PLL, D/A Converter ........................ 11-33
Slot Receiver, Sample Pulse Gen., RS422 Interface,
Charactor Out, Current Limitter .............................................. 11-34
System Control, H BLK/V BLK P Gen., H/V Sync Gen.,
EEPROM ................................................................................. 11-37
Signal Gen., PWM Control, HV REG/HV Out Switching,
Dynamic Focus, Landing/NTC Out, H LIN Conv.,
D/A Converter ......................................................................... 11-38
Signal Generator, PWM Control, H/V Out, H LIN Amp. ....... 11-39
Signal Generator, CY H/CY V Out, ROT Out,
D/A Converter ......................................................................... 11-40
R.G.B Out, BLK Out, H.STAT Out ........................................ 11-43
F.B.T ........................................................................................ 11-44
Tally ......................................................................................... 11-45
Indicator .................................................................................. 11-45
Relay ....................................................................................... 11-45
Relay (BVM-14G1/20G1) ...................................................... 11-45
PFC Control, Main Rect .......................................................... 11-46
PWM Control, Converter Out, Protector Encoder,
D+5V. ±6V. ±15V. +120V. HT Rect. ....................................... 11-47
Function Control (BVM-14G5, BKM-10R) ........................... 11-49
Function Control (BVM-14G5, BKM-10R) ........................... 11-50
CPU, Memory Card Driver, RS422 Driver,
Card Address Decoder (BVM-14G5, BKM-10R) .................. 11-51
Mother ..................................................................................... 11-53
Mother ..................................................................................... 11-54
BK (3/9)
BK (4/9)
BK (5/9)
BK (6/9)
BK (7/9)
BK (8/9)
BK (9/9)
BC (1/4)
BC (2/4)
BC (3/4)
BC (4/4)
E (1/4)
E (2/4)
E (3/4)
E (4/4)
C
P
YA
YB
YC
HD
G (1/2)
G (2/2)
HA
HB
HC
TA
TB
• All capacitors are in µF unless otherwise noted. pF: µµF 50WV or
less are not indicated except for electrolytics.
• Indication of resistance, which does not have one for rating electrical power, is as follows.
Page
Reference information
RESISTOR
Pitch: 5 mm
Rating electrical power 1/4W
•
•
•
•
•
•
•
All resistors are in ohms. (1M: 1000kΩ, 1k: 1000Ω)
: nonflammable resistor.
Chip resister are 1/10W unless otherwise noted.
: fusible resistor.
¢ : internal component.
: panel designation and adjustment repair.
All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• METAL CHIP (:RN, :RN-CP) resister in 1%, 0.5%, 1/4W unless
otherwise specified.
• The components identified by
in this basic schematic diagram
have been carefully factory-selected for each set in order to satisfy regulations regarding X-ray radiation.
Should replacement be required, replace only with the value originally used.
• When replacing components identified by
, make the necessary adjustments indicated, If results do not meet the specified
value change the component identified by
and repeat the adjustment until the specified value is achieved. (Refer to page 4-1
to 4-3.)
Part replaced (
)
Checked
R307, R332, R333, R336, R337,
R338, IC301, IC302, PH301
..................................... G board
(+B VOLTAGE)
R501, R502, R503, R504, R505,
R511, IC501, IC502, IC503
..................................... E board
(HIGH VOLTAGE)
R571, IC501 ................. E board
R901, R902, R903 ....... P board
R912, R913, IC901 .... BK board
(BEAM CURRENT)
R531, R532, R533, R534, R542,
R543, R544, R545, R548, IC071,
IC502, IC531 ................ E board
R904, R905, R906 ....... P board
(HOLD-DOWN)
• All voltages are in V.
• Reading are taken with Component color-bar signal (R.G.B SYNC)
input.
• Voltage are dc with respect to ground unless otherwise noted.
• no mark : 14G1/14G5 series and comon
(
) : 20G1 series
• Voltage variation may be noted due to normal production tolerancd.
•
: B+, B– line
•
: signal path
• Circled numbers are waveforms reference.
11-15
11-15
COIL
CAPACITOR
: RN
: RC
: FPRD
: FUSE
: RW
: RS
: RB
: LF-8L
: TA
: PS
: PP
: PT
: MPS
: MPP
: ALB
: ALT
: ALR
METAL FILM
SOLID
NONFLAMMABLE CARBON
NONFLAMMABLE FUSIBLE
NONFLAMMABLE WIREWOUND
NONFLAMMABLE METAL OXIDE
NONFLAMMABLE CEMENT
MICRO INDUCTOR
TANTALUM
STYROL
POLYPROPYLENE
MYLAR
METALIZED POLYESTER
METALIZED POLYPROPYLENE
BIPOLAR
HIGH TEMPERATURE
HIGH RIPPLE
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
FRAME (1/3)
YA
+12V
TALLY
FRAME (1/3)
2
1
1
TB
CN201
4P
YB
OVER LOAD
STANDBY
POWER
+5V
TO BC BOARD
CN1
1
2
3
4
CN6
6P
WHT
CN301
8P
YC
CN302
D-SUB
NC
NC
RTS
GND
NC
TXD
+5V
RXD
1
+12V
2
_TALLY
3 OVER LOAD
4
STANDBY
5
POWER
6
+5V
1
2
3
4
5
6
7
8
(14G5,BKM-10R ONLY)
HB
CN101
6P
RED
HA
CN201
6P
WHT
CN202
10P
WHT
HC
6
5
4
3
2
1
CE2
MISO
MOSI
SCLK
+5V
GND
6
5
4
3
2
1
CN7
8P
YEL
1 V SYNC(NC)
2 H SYNC(NC)
3
RTS
4
GND
5
NC
6
TXD
7
+5V
8
RXD
CN8
9P
WHT
1
2
3
4
5
6
7
8
9
1
GND
2
+5V
ENCODER0 3
ENCODER0 4
ENCODER1 5
ENCODER1 6
ENCODER2 7
ENCODER2 8
ENCODER3 9
ENCODER3 10
EN0B
EN0A
EN1B
EN1A
EN2B
EN2A
EN3B
EN3B
+5V
GND
10
9
8
7
6
5
4
3
2
1
CN5
6P
RED
CE2
MISO
MOSI
SCLK
+5V
GND
6
5
4
3
2
1
CN4
6P
WHT
CE1
MISO
MOSI
SCLK
+5V
GND
6
5
4
3
2
1
GND
RXD
TXD
GND
+5V
GND
RXD
TXD
GND
9
8
7
6
5
4
3
2
1
CN3
10P
MEMORY
CARD
CE1
MISO
MOSI
SCLK
+5V
GND
GND
_TXD
RXD
GND
+5V
GND
TXD
_RXD
GND
(14G1/20G1 ONLY)
HD
CN101
D SUB
CN102
9P
GND
TXD
RXD
GND
+5B
GND
TXD
RXD
GND
9
8
7
6
5
4
3
2
1
TO BC BOARD
CN2
A1
GND
B1
GND
A2
+B
B2
+B
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
VIDEO
A9
PY OUT
B9
PC OUT
A10
GND
B10
Y/G
A11
GND
B11
PB/B
A12
GND
B12
PR/R
A13
SLOT6
B13
SLOT7
A14
SLOT4
B14
SLOT5
A15
SLOT2
B15
SLOT3
A16
SLOT0
B16
SLOT1
A17
GND
B17 _CHAR.BLK
A18 _CHAR.G
B18 _CHAR.B
A19 _CHAR.R
B19 AFC.PULSE
A20
H SYNC
B20
V SYNC
A21 2H SYNC
B21 2V SYNC
A22
NC
B22
NC
A23
NC
B23
NC
A24
NC
B24
V.BLK1
A25
H.BLK
B25
V.BLK2
A26
NC
B26
RESET
A27 S.PULSE
B27
MISO
A28
MOSI
B28
SCLK
A29 DIGITAL +5V
B29 DIGITAL +5V
A30 DIGITAL.GND
B30 DIGITAL.GND
A31
NC
B31 INT SIG
A32
GND
B32
GND
CN1
64P
B TO B
(14G5 ONLY)
CN5
64P
B TO B
A1
GND
B1
GND
A2
GND
B2
GND
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
VIDEO
A9
GND
B9
PY
A10
GND
B10
PC
A11
GND
B11
Y/G
A12
GND
B12
2Y/2G
A13
GND
B13
PB/B
A14
GND
B14
2PB/2B
A15
GND
B15
PR/R
A16
GND
B16
2PR/2R
A17
GND
B17 _CHAR.BLK
A18 _CHAR.G
B18 _CHAR.B
A19 _CHAR.R
B19 H PULSE
A20
_HS
B20
_VS
A21
_2HS
B21
_2VS
A22
NC22A
B22
NC22B
A23
NC23A
B23
NC23B
A24 H PULSE
B24
V.BLK1
A25
H.BLK
B25
V.BLK2
A26 +5V.SENSE
B26
RESET
A27 S.PULSE
B27
MISO
A28
MOSI
B28
SCLK
A29 DIGITAL +5V
B29 DIGITAL +5V
A30 DIGITAL.GND
B30 DIGITAL.GND
A31 CH.SLOT5
B31 INTERNAL.SIG
A32
GND
B32
GND
A1
GND
B1
GND
A2
+120V
B2
+120V
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
DU G
B8
DU B
A9
DU R
B9
VP S
A10
ABL
B10 G2.CONTROL
A11
GND
B11
Y/G
A12
GND
B12
2Y/2G
A13
GND
B13
PB/B
A14
GND
B14
2PB/2B
A15
GND
B15
PR/R
A16
GND
B16
2PR/2R
A17
GND
B17 CHAR.BLK
A18
CHAR.G
B18
CHAR.B
A19
CHAR.R
B19 AFC.PULSE
A20
HS
B20
VS
A21
2HS
B21
2VS
A22
NC
B22
NC
A23
NC
B23
NC
A24
NC
B24
V.BLK1
A25
H.BLK
B25
V.BLK2
A26 +5V.SENSE
B26
RESET
A27 S.PULSE
B27
MISO
A28
MOSI
B28
SCLK
A29 DIGITAL +5V
B29 DIGITAL +5V
A30 DIGITAL.GND
B30 DIGITAL.GND
A31 CH.SLOT3
B31 INTERNAL.SIG
A32
GND
B32
GND
CN2
64P
B TO B
A1
GND
B1
GND
A2
+120V
B2
+120V
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
DUG
B8
DUB
A9
DUR
B9
VSP
ABL OUT A10
G2.CONTROL B10
AFC.PULSE A11
B11
_HS
A12
_VS
B12
_2HS
A13
_2VS
B13
NC22A
A14
NC22B
B14
NC23A
A15
NC23B
B15
NC24A
V.BLK1 A16
B16
H.BLK
V.BLK2 A17
+5V.SENSE B17
A18
RESET
B18
NC
A19
MISO
B19
MOSI
DIGITAL +5V A20
DIGITAL +5V B20
DIGITAL +5V A21
DIGITAL +5V B21
DIGITAL.GND A22
DIGITAL.GND B22
DIGITAL.GND A23
DIGITAL.GND B23
_CH.SLOT2 A24
_CH.SLOT1 B24
A25
SCLK
INTERNAL.SIG B25
1
TO
TA BOARD
CN14
2
3
4
CN4
50P
CN3
64P
B TO B
B-SS3280<AEP>-KESSENZU-P2
(BKM-10R ONLY)
9
8
7
6
5
4
3
2
1
GND
TXD
RXD
GND
+5B
GND
TXD
RXD
GND
CN102
9P
5
HD
CN101
D SUB
11-17
B
TO BK BOARD
CN1
TO OPTION BOARD
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A21
B21
A22
B22
A23
B23
A24
B24
A25
B25
A26
B26
A27
B27
A28
B28
A29
B29
A30
B30
A31
B31
A32
B32
CN1
PCMCIA
CN2
9P
A
GND
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
+12V
TALLY
+5V
_STANDBY
_POWER
_OVERLOAD
-H.SYNC
_V.SYNC
RTS(OPTION)
GND
NC
RXD(OPTION)
+5V
TXD(OPTION)
GND
_TXD
RXD
GND
+5V
GND
TXD
_RXD
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
GND
GND
C
D
11-17
E
F
G
H
FRAME (2/3)
FRAME (2/3)
DY
1
H.DY
TO E BOARD
CN801
TO
TB BOARD
CN4
1
2
3
A1
GND
B1
GND
A2
+120V
B2
+120V
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
DU G
B8
DU B
A9
DU R
B9
VS P
A10 ABL OUT
B10 G2.CONTROL
A11 AFC.PULSE
B11
_HS
A12
_VS
B12
_2HS
A13
_2VS
B13
NC22A
A14
NC22B
B14
NC23A
A15
NC23B
B15
NC24A
A16
V.BLK1
B16
H.BLK
A17
V.BLK2
B17 +5V.SENSE
A18
RESET
B18
NC27A
A19
MISO
B19
MOSI
A20 DIGITAL +5V
B20 DIGITAL +5V
A21 DIGITAL +5V
B21 DIGITAL +5V
A22 DIGITAL.GND
B22 DIGITAL.GND
A23 DIGITAL.GND
B23 DIGITAL.GND
A24 _CH.SLOT2
B24 _CH.SLOT1
A25
SCLK
B25 INTERNAL.SIG
CN14
50P
4
TA
TO E BOARD
CN802
B32
GND
A32
GND
B31
+B
A31
+B
B30
GND
A30
GND
B29
-15V
A29
-15V
B28
+15V
A28
+15V
B27
-6V
A27
-6V
B26
+6V
A26
+6V
B25
DU G
A25
DU B
B24
DU R
A24
VS P
B23
ABL
A23
G2.CNT
B22
HCR
A22
VCR
B21
H.CY
A21
V.CY
B20
H.STAT
A20
V.STAT
B19
HCT
A19 POWER.ON
B18 DEGAUSS
A18 E.PROTECT
B17 G.PROTECT1
A17 G.PROTECT2
B16 G.PROTECT3
A16 G.PROTECT4
B15
GND
A15
GND
B14
VD
A14
AFC.P
B13
HS
A13
VS
B12
2HS
A12
2VS
B11
NC
A11
NC
B10
NC
A10
NC
B9
HP
A9 V.BLK.P1
B8 H.BLK.P
A8 V.BLK.P2
B7 +5V.SENSE
A7
RESET
B6
NC
A6
MISO
B5
MOSI
A5
SCLK
B4 DIGITAL +5V
A4 DIGITAL +5V
B3 DIGITAL.GND
A3 DIGITAL.GND
B2 _CH.SLOT2
A2 INTERNAL.SIG
B1
GND
A1
GND
GND
GND
LCC RET
LCC RET
LCC
LCC
ROT RET
ROT RET
ROT
ROT
NTC RET
NTC RET
NTC
NTC
CY(V)RET
CY(V)RET
CY(V)
CY(V)
CY(H)RET
CY(H)RET
CY(H)
CY(H)
HV PROT
HV R(AC)
ABL2
HV R(DC)
+15V
ABL1
+15V
NC
GND
GND
H.STAT C
G2 C
+12V
+12V
GND
GND
-12V
-12V
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
GND
GND
CN11
64P
B TO B
CN13
64P
B TO B
TO G BOARD
CN3
B32
A32
B31
A31
B30
A30
B29
A29
B28
A28
B27
A27
B26
A26
B25
A25
B24
A24
B23
A23
B22
A22
B21
A21
B20
A20
B19
A19
B18
A18
B17
A17
B16
A16
B15
A15
B14
A14
B13
A13
B12
A12
B11
A11
B10
A10
B9
A9
B8
A8
B7
A7
B6
A6
B5
A5
B4
A4
B3
A3
B2
A2
B1
A1
A1
GND
B1
GND
A2
+120V
B2
+120V
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
GND
A9
GND
B9
GND
A10
GND
B10
GND
A11
GND
B11
GND
A12
GND
B12
GND
A13
GND
B13
GND
A14
GND
B14 _POWER.ON
A15 _DEGAUSS
B15
_E.PROT
A16 _G.PROT1
B16 _G.PROT2
A17 _G.PROT3
B17 _G.PROT4
A18
GND
B18
GND
A19
VD
B19 AFC.PULSE
A20
_HS
B20
_VS
A21
_2HS
B21
_2VS
A22
HT(+)
B22
HT(+)
A23
HT(-)
B23
HT(-)
A24
NC24A
B24
V.BLK1
A25
H.BLK
B25
V.BLK2
A26 +5V.SENSE
B26
RESET
A27
NC
B27
MISO
A28
MOSI
B28
SCLK
A29 DIGITAL +5V
B29 DIGITAL +5V
A30 DIGITAL.GND
B30 DIGITAL.GND
A31
NC
B31 INTERNAL.SIG
A32
GND
B32
GND
HT(-)
HT(+)
GND
+12V
-12V
GND
G2 CTRL
H.STAT CTRL
1 H.STAT CTRL CN508
8P
WHT
2 G2 CTRL
3
GND
4
-12V
5
+12V
6
GND
7
H1
8
H2
1
2
3
4
5
6
7
8
CN16
8P
WHT
H.DY
E
V.DY
H.DY V.DY
CN504
4P
RED
2
TO BK BOARD
CN2
1
2
3
4
CN007
6P
WHT
DY
V.DY
1
2
3
4
5
6
H.DY
H.DY
H.DY.RET
H.DY.RET
V.DY.RET
V.DY
1
2
3
G2 OUT
NC
GND
1
2
3
4
5
FBT(H)
FBT(C)
JW(15V)+
GND
JW(15V)-
KR
NC
NC
GND
CN505
4P
WHT
CN20
3P
WHT
LCC RTN
NC
LCC
3
TO BK BOARD
CN3
1
2
3
1
2
3
4
CN506
4P
BLK
LCC
CN19
2P
WHT
ROT RTN
ROTATION
4
TO BK BOARD
CN4
1
2
KG
NC
NC
GND
1
2
3
4
CN503
3P
+600V
NC
GND
CN903
3P
1
2
3
J501
CRT SOCKET
KB
NC
NC
GND
G4
1
GM
1
ROT(20INCH ONLY)
CN18
2P
WHT
CN507
3P
5
NTC RETURN 1
2
NTC
1
2
3
G1
GND
+120V
C
NTC
CN17
4P
WHT
CY(V)RTN)
CY(V)
CY(H)RTN
CY(H)
TO BK BOARD
CN5
CN502
:TAB
GND
1
CN501
2P
WHT
GND
GND
2
1
V901
PICTURE TUBE
4
3
2
1
(20INCH ONLY)
CN15
11P
WHT
HV RTN(AC) 1
+15V(JW) 2
+15V(JW) 3
ABL OUT 4
IK PROT 5
+15V(JW) 6
+15V(JW) 7
8
GND
HV PROT 9
10
GND
HV RTN(DC) 11
CHASSIS
1 HV RTN(AC) CN902
11P
WHT
2 +15V(JW)
3 +15V(JW)
4
ABL
5
IK PROT
6 +15V(JW)
7 +15V(JW)
8
GND
9
HV PROT
10
GND
11 HV RTN(DC)
FV1
1
FV2
1
HV
1
FBT(H)
FBT(C)
JW(15V)+
GND
JW(15V)+
1
2
3
4
5
T901
FBT
CN902
5P
CN901
5P
WHT
P
CN904
2P
WHT
4
3
2
1
JW(+15V)
JW(+15V)
IK OUT
IK IN
CN903
4P
WHT
DFX
DFY
CN905
2P
1
2
1
2
DFX
DFY
GND
GND
+B
+B
GND
GND
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
DU.G
DU.B
DU.R
V.SP
ABL
G2.CNT
HCR
VCR
H.CY
V.CY
H.STAT
V.STAT
HCT
POWER.ON
DEGAUSS
E_PROT
G.PROT1
G.PROT2
G.PROT3
G.PROT4
GND
GND
VD
AFC.P
HS
VS
2HS
2VS
NC
NC
NC
NC
HP
V.BLK.P1
H.BLK.P
V.BLK.P2
5V_SENCE
RESET
1
MISO
MOSI
SCLK
D_5V
D_5V
D_GND
D_GND
CH_SLOT2
IRQ
GND
GND
CN801
64P
B TO B
B32
A32
B31
A31
B30
A30
B29
A29
B28
A28
B27
A27
B26
A26
B25
A25
B24
A24
B23
A23
B22
A22
B21
A21
B20
A20
B19
A19
B18
A18
B17
A17
B16
A16
B15
A15
B14
A14
B13
A13
B12
A12
B11
A11
B10
A10
B9
A9
B8
A8
B7
A7
B6
A6
B5
A5
B4
A4
B3
A3
B2
A2
B1
A1
TO
TA BOARD
CN11
TO
TA BOARD
CN13
B32
A32
B31
A31
B30
A30
B29
A29
B28
A28
B27
A27
B26
A26
B25
A25
B24
A24
B23
A23
B22
A22
B21
A21
B20
A20
B19
A19
B18
A18
B17
A17
B16
A16
B15
A15
B14
A14
B13
A13
B12
A12
B11
A11
B10
A10
B9
A9
B8
A8
B7
A7
B6
A6
B5
A5
B4
A4
B3
A3
B2
A2
B1
A1
GND
GND
LCC RET
LCC RET
LCC
LCC
ROT RET
ROT RET
ROT
ROT
NTC RET
NTC RET
NTC
NTC
CY(V)RET
CY(V)RET
CY(V)
CY(V)
CY(H)RET
CY(H)RET
CY(H)
CY(H)
HV PROT
HV R(AC)
ABL2
HV R(DC)
+15V
ABL1
+15V
NC
GND
GND
H.STAT
G2 C
+12V
+12V
GND
GND
-12V
-12V
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
GND
GND
A1
GND
B1
GND
A2
+120V
B2
+120V
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
GND
A9
GND
B9
GND
A10
GND
B10
GND
A11
GND
B11
GND
A12
GND
B12
GND
A13
GND
B13
GND
A14
GND
B14 POWER
A15 DEGAUSS
B15
E PROT
A16 G PROT 1
B16 G PROT 2
A17 G PROT 3
B17 G PROT 4
A18
GND
B18
GND
A19
VD
B19 AFC PULSE
A20
HS
B20
VS
A21
2HS
B21
2VS
A22
HT(+)
B22
HT(+)
A23
HT(-)
B23
HT(-)
A24
NC
B24
V BLK
A25
H BLK
B25
V BLK2
A26 +5V SENSE
B26
RESET
A27
1
B27
MISO
A28
MOSI
B28
SCLK
A29DIGITAL +5V
B29DIGITAL +5V
A30DIGITAL GND
B30DIGITAL GND
A31
NC
B31
IRQ
A32
GND
B32
GND
TO
TA BOARD
CN12
CN802
64P
B TO B
DGC
S901
MAIN POWER
AC SW IN
AC SW OUT
AC SW IN
CN3
64P
AC SW OUT
7
6
5
4
3
2
1
CN2
7P
3
2
1
AC IN
100-240V
50/60HZ
CN12
64P
B TO B
LIVE
NEUTRAL
CN1
3P
G
B-SS3280<AEP>-KESSENZU-P1
5
11-18
A
B
C
D
11-18
E
F
G
H
FRAME (3/3)
FRAME (3/3)
1
BC
CN1
64P
B TO B
A1
GND
B1
GND
A2
+B
B2
+B
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
VIDEO
P.Y. OUT A9
P.C. OUT B9
A10
GND
B10
Y/G
A11
GND
B11
PB/B
A12
GND
B12
PR/R
SLOT_6 A13
SLOT_7 B13
SLOT_4 A14
SLOT_5 B14
SLOT_2 A15
SLOT_3 B15
SLOT_0 A16
SLOT+1 B16
A17
GND
CHAR_BLANK B17
CHAR_G A18
CHAR_B B18
CHAR_R A19
B19
AFC
H SYNC A20
V SYNC B20
2H SYNC A21
2V SYNC B21
A22
NC
B22
NC
A23
NC
B23
NC
A24
NC
V BLANK1 B24
H BLANK A25
V BLANK2 B25
A26
NC
B26
RESET
SAMPLE PULSE A27
B27
MISO
A28
MOSI
B28
SCLK
DIGITAL +5V A29
DIGITAL +5V B29
DIGITAL.GND A30
DIGITAL.GND B30
A31
NC
INT. SG B31
A32
GND
B32
GND
CN1
64P
B TO B
CN2
64P
B TO B
TO
TB BOARD
CN1
TO
TB BOARD
CN5
A1
GND
B1
GND
A2
NC
B2
NC
A3
NC
B3
NC
A4
NC
B4
NC
A5
NC
B5
NC
A6
NC
B6
NC
A7
NC
B7
NC
A8
NC
B8
NC
A9
NC
B9
NC
A10
NC
B10
NC
A11
NC
B11
NC
A12
NC
B12
NC
A13
+12V
B13
TALLY
A14 OVERLOAD
B14 STANDBY
A15
POWER
B15
+5V
A16
H SYNC
B16
V SYNC
A17 OPTION RTS
B17
GND
A18
NC
B18 OPTION RXD
A19
+5V
B19 OPTION TXD
A20
GND
B20
TXD
A21
RXD
B21
GND
A22
+5V
B22
GND
A23
TXD
B23
RXD
A24
GND
B24
NC
A25
NC
B25
NC
A26
NC
B26
NC
A27
NC
B27
NC
A28
NC
B28
NC
A29
NC
B29
NC
A30
NC
B30
NC
A31
NC
B31
NC
A32
GND
B32
GND
CN3
CN4
REMOTE 1
IN
REMOTE 1
OUT
TO
TB BOARD
CN3
CN5
CN6
REMOTE 2
ISR
INTERACTIVE
STATUS
REPORTING
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A21
B21
A22
B22
A23
B23
A24
B24
A25
B25
A26
B26
A27
B27
A28
B28
A29
B29
A30
B30
A31
B31
A32
B32
GND
GND
+B
+B
GND
GND
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
DU G
DU B
DU R
V.S.P
ABL
G2 CNTROL
GND
Y/G
GND
2Y/2G
GND
PB/B
GND
2PB/2B
GND
PR/R
GND
2PR/2R
GND
CHAR BLK
CHAR G
CHAR B
CHAR R
AFC PULSE
HS
VS
2HS
2VS
NC
NC
NC
NC
H.PULSE
V BLK1
H.BLK
V BLK2
+5V SENSE
RESET
S.PULSE
MISO
MOSI
SCLK
DIGITAL +5V
DIGITAL +5V
DIGITAL.GND
DIGITAL.GND
CH SLOT5
NC
GND
GND
CN2
4P
RED
:S-MICRO
KR
NC
NC
GND
2
1
2
3
4
TO C BOARD
CN504
1
2
3
4
TO C BOARD
CN505
CN3
4P
WHT
:S-MICRO
KG
NC
NC
GND
3
2
CN4
4P
BLK
:S-MICRO
BK
KB
NC
NC
GND
4
1
2
3
4
TO C BOARD
CN506
1
2
3
TO C BOARD
CN507
CN5
5P
WHT
:S-MICRO
G1
NC
GND
5
TB-1
ANALOG
Y/G IN
Y/G OUT
3
B-Y BIN
B-Y/B OUT
R-Y/R IN
R-Y/R OUT
SYNC IN
SYNC OUT
4
B-SS3280<AEP>-KESSENZU-P3
5
11-19
A
B
C
D
11-19
E
F
G
H
BK (1/9)
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠
BK
SELECT(9/9)
Y CLAMP OFFSET(9/9)
Q101
DTA144EKA
BK SELECT SW
Y/G(8/9,9/9)
2Y/2G (9/9)
+5V
0
C102
22
16V
:BP-CP
G
IN
0
1
R104
Q102
120
2SC3545
:CHIP Y/G
BUFFER
0.7
R102
1k
:CHIP
R101
270k
:CHIP
Y/G
R106
100 1.4
:CHIP
R124 0.7
1k
:CHIP 0
TP100
G
VCC
12
13
X 14
0
X0
X1
R116
2.2k
:CHIP
R114
1k
:RN-CP
1
16
R110
22
:CHIP 0
0.7
TB1
ANALOG
IC101(1/3)
MC74HC4053FEL
PROGRAM SELECT
Q100
2SA1462
5.1
Y/G BUFFER
R105
D102
R100
1.2k
MA111
33k
DC SHIFT :CHIP
:CHIP
+5V
+5V
R112
3.3k
:RN-CP
Q105
2SC3545
Y/G CLAMP
1.4
R115
220
:CHIP
1.4
Q103
2SA1462
Y/G CLAMP
G IC102(2/2)
IC101(2/3)
MC74HC4053FEL
PULSE INSERT
TL082CPS
0.7 Y/G CLAMP
IC101(3/3)
MC74HC4053FEL
Y/G CLAMP
C104
0.022
B:CHIP
0.7
3
2
0.7
R126
330k
:CHIP
8
1
2
1
0
Y 15
0
Y0
Y1
6
5
C122
47
16V
:HT-CP
7
0
G
0.8
5 Z0
3 Z1
G
4
Z
Y/G OUT (2/9)
IC325
TC4W53FU
R-Y GAIN CONTROL
0.8
C
4 -0.3
OUT
2
IN
3
OUT
4
IN
5
OUT
6
6
5
IN
7
R483
1k
:CHIPIC320(2/2)
OUT
8
9
C101
12p
C100 CH:CHIP
10p
CH:CHIP
B
B-Y/B
R109 -5.2
22
:CHIP
D103
MA111
PROTECTOR
R103
100k
:CHIP
R107
1k
:CHIP
R111
1.8k
:RN-CP
R108
1k
:CHIP
R118
22
:CHIP
R117
2.2k
:CHIP
-4.5
60 11 7 8
Q104
2SC3545
Y/G CLAMP
R119
5.6k
:CHIP
B
R113 0.7
100
:CHIP
0.9 10
C103
0.047
25V
B:CHIP
-5V
R
R-Y/R
A VEE GND
0.6 9
IC102(1/2)
TL082CPS
Y/G CLAMP
C326
0.22
25V
F:CHIP
R125
1M
:CHIP
1.3
7
-5V
PROG-SW
0.5
0
0.1
0
TL082CPS
R-Y GAIN
CONTROL
SYNC
C324
0.01
F:CHIP
8
R485
10k
:CHIP
1
C327
0.047
25V
B:CHIP
2
7
6
5
VDD
CH0
CH1
ADR
5V
COM
INH
VEE
VSS
1
BK (1/9)
2
3
4
0
-5V
PR/R(9/9)
2PR/2R(9/9)
+5V
+5V
0.7
D303
MA111
PROTECTOR
R303
100k
:CHIP
R301
270k
:CHIP
C301
C300
10p
12p
CH:CHIP CH:CHIP
R307
1k
:CHIP
R309 -5.2
22
:CHIP
X 14
0
Q303
2SA1462
R-Y/R CLAMP
1.4
-4.5
6 0 11 7 8
2 Y0
1 Y1
0.8
R312
Q304
1.8k
2SC3545
:RN-CP R-Y/R CLAMP
R320
2.2k
:CHIP
15
Y
7
0
0
0.8
0.9 10
-0.4
4
R322
5.6k
:CHIP
B
R314
22
:CHIP
8
6
5
16
0.8
0.8
5
Z0
3
Z1
C
0.1
0.6 9
Z
1.1
8
4
R
C307
2.2
16V
F:CHIP
C304
0.047
25V
B:CHIP
C322
100
6.3V
:HT-CP
-5V
C305
0.022
B:CHIP
0
R318
220
:CHIP
A VEE GND
R308
1k
:CHIP
IC301(2/3)
MC74HC4053FEL
PULSE INSERT
R
R321
22
:CHIP
7
6
5
OUT
X0
X1
1.4
DC
VCC
12
13
Q302
2SC3545
R-Y/R BUFFER
R324 0.7
1k
:CHIP 0
1
2
3
4
C308
0.68
16V
F:CHIP
IC304(1/3)
MC74HC4053FEL
RGB SELECT
R327
100
:CHIP 1.1
1.3
VEE
R302
1k
:CHIP
R
IC301(3/3)
IC303
MC74HC4053FEL
CXA1521M
R-Y/R CLAMP R-Y GAIN CONTROL
GND
R304
22
:CHIP
TP300
R481
1M
:CHIP
Q305
2SC3545
R-Y/R CLAMP
GAIN
0
R317
1k
:RN-CP
2
16
R310
22
:CHIP 0
R319
2.2k
:CHIP
VCC
R306
100 1.4
:CHIP
0.7
R
R313
3.3k
:RN-CP
IC301(1/3)
MC74HC4053FEL
PROGRAM SELECT
GND
C302
22
16V
:BP-CP
Q301
DTA144EKA
BK SELECT SW
IN
0
Q300
2SA1462
R-Y/R BUFFER5.2
R305
D302
R300
1.2k
MA111
33k
DC SHIFT :CHIP
:CHIP
Q310
2SC2412K
R-Y GAIN
CONTROL
12 X0
13 X1
0.5
0.5
VCC
R328
10k
:CHIP
X 14
0.4
C309
0.047
25V
B:CHIP
A VEE GND
R486
2.2k
:CHIP
6 11 7 8
0.1
1
IC302(2/2)
TL082CPS
R-Y/R CLAMP
0.8
-0.3
-5V
IC302(1/2)
TL082CPS
R-Y/R CLAMP
+5V
3
-0.3
2
3
0.4
0.4
PR OUT(2/9)
R OUT(2/9)
R
-5V
B
IC503
CXA1521M
B-Y/B GAIN
CONTROL
+5V
A VEE GND
R512
1.8k
:RN-CP
6 11 7 8
0.1
B
0
2 Y0
1 Y1
0.8
Q504
2SC3545
B-Y/B CLAMP
R520
2.2k
:CHIP
Y
15
-0.7
4
R522
5.6k
:CHIP
0.8
0.9 10
0.8
5 Z0
3 Z1
0.1
7
0
B
R514
22
:CHIP
C505
0.022
B:CHIP
8
6
5
0
IC502(1/2)
TL082CPS
B-Y/B CLAMP
Z
C507
2.2
16V
F:CHIP
C
9
C504
0.047
25V
B:CHIP
R316
82k
:RN-CP
EXT SYNC
(8/9)
8
3
2
Q801
2SA1037K
EXT SYNC AMP
0
4
C800
C801
R802
33k
12p
12p
CH:CHIP CH:CHIP :CHIP
1
0.1
5 Z0
3 Z1
0.7
R-Y CLAMP OFFSET(9/9)
R-Y PULSE LEVEL(9/9)
4
R311
82k
:RN-CP
IC320(1/2)
TL082CPS
IC520(1/2)
TL082CPS
1
2
3
4
R315
11k
:RN-CP
Q510
2SC2412K 0.5
B-Y/B GAIN
CONTROL
12 X0
13 X1
0.5
VCC
X
-0.2
14
0.4
0.4
0.4
2
3
1
IC502(2/2)
TL082CPS
B-Y/B CLAMP
A VEE GND
6 11 7 8
0.1
R686
2.2k
:CHIP
C510
0.047
25V
B:CHIP
R683
1k
:CHIP
C303 C323
2.2
2.2
16V
16V
F:CHIP F:CHIP
Z
C526
0.22
25V
F:CHIP
0.1
43
2
8 0.1
1
0
8
R685
10k
:CHIP
7
C
R482 0.2 9
3.9k
:RN-CP
WHITE SAMPLING P
(3/9,4/9,5/9,6/9,7/9)
4
1.2
IC520(2/2)
TL082CPS
B-Y/B GAIN
CONTROL
IC300(1/2)
TL082CPS
BUFFER
0.5
C524
0.01
F:CHIP
IC500(2/3)
MC74HC4053FEL
R-Y REF SELECT
R480
330k
:RN-CP
8
3
2
1
5
-0.2
+5V
0.9
R803
1k
:CHIP
6
C509
0.68
16V
F:CHIP
R530
10k
:CHIP
-5V
R804
3.9k
:CHIP
C804
22
16V
:BP-CP
7
0.8
+5V
4
1.2
8
4
0.8
0.6
-5V
≠≠≠≠≠≠
≠≠≠≠≠≠≠
PROG
SW(9/9)
16
6
5 0
7
6
CHROMA(9/9)
0.1
1
2
3
R528
43k
:RN-CP
5
VDD
CH0
CH1
ADR
R508
1k
:CHIP
-4.5
R521
22
:CHIP
B
OUT
Q503
2SA1462
B-Y/B CLAMP
1.4
R518
220
:CHIP
IC501(3/3)
MC74HC4053FEL
B-Y/B CLAMP
IC504(1/3)
MC74HC4053FEL
RGB SELECT
IC525
TC4W53FU
B-Y/B GAIN
CONTROL
COM
INH
VEE
VSS
R507
1k
:CHIP
R509 -5.2
22
:CHIP
1.4
IC501(2/3)
MC74HC4053FEL
PULSE INSERT
VEE
0.6
D503
MA111
PROTECTOR
R503
100k
:CHIP
R501
270k
:CHIP
X 14
-0.1
1.2
B OUT(2/9)
PB OUT(2/9)
+5V
R529
100
1.2 :CHIP
GND
R502
1k
:CHIP
C501
C500
12p
10p
CH:CHIP CH:CHIP
Q502
2SC3545
B-Y/B BUFFER
X0
X1
R681
1M
:CHIP
Q505
2SC3545
B-Y/B CLAMP
GAIN
R504
22
:CHIP
VCC
12
13
R517
1k
:RN-CP
R519
2.2k
:CHIP
DC
0
3
16
R510
22
:CHIP 0
0.6
B
R513
C520
2.2
3.3k
16V
:RN-CP
F:CHIP
TP500 R524 0.6
1k -0.1
B :CHIP
VCC
IC501(1/3)
MC74HC4053FEL
PROGRAM SELECT
GND
C502
22
16V
:BP-CP
Q501
Q500
DTA144EKA
2SA1462
BK SELECT SW
B-Y/B BUFFER
5.1
R505 0
R506
D502
R500
1.2k
MA111
100
33k
DC SHIFT :CHIP
:CHIP 1.3
:CHIP
IN
PB/B(9/9)
2PB/2B(9/9)
C508
2.2
16V
F:CHIP
R527
15k
:RN-CP
4
C527 0
0.047
25V
B:CHIP
BLACK SAMPLING P
(2/9,3/9,4/9,5/9,6/9,7/9)
-5V
-5V
16
IC500(1/3)
MC74HC4053FEL
CLAMP PULSE
SELECT
5
VCC
X
Q902
DTA144EKA
SIGNAL OFF SW
0.9
14
IC912
TC7W32FU
MONO SW
5.3
A VEE GND
0.1
0.6
8
R970
10k
:CHIP
6
0.2
60 11 7 8
1
≠≠≠≠≠
≠≠≠≠≠≠
RGB
SW(2/9,9/9)
+5V
MONO
(9/9)
7
5
GND
0.9
12 X0
13 X1
0.7
Y CLAMP PULSE(8/9)
C CLAMP PULSE(8/9)
R516
82k
:RN-CP
VCC
+5V
2
3
B-Y CLAMP OFFSET(9/9)
(9/9)
B-Y PULSE LEVEL
R511
82k
:RN-CP
4
-5V
0.4 0.2 0.6
-5V
IC500(3/3)
MC74HC4053FEL
B-Y REF SELECT
R680
330k
:RN-CP
R515
9.1k
:RN-CP
C503 C523
2.2
2.2
16V
16V
F:CHIP F:CHIP
0.1
2 Y0
1 Y1
0.6
Y
IC300(2/2)
TL082CPS
BUFFER
15 5
0.1
7
0.16
B
R682 0.2 10
3.9k
:RN-CP
WHITE INSERT P(2/9,7/9)
CONT
≠≠≠≠≠≠
≠≠≠≠≠0 (9/9)
BK(1/9)
V BLK1 (9/9)
(SIGNAL IN SELECTOR,RGB GAIN CONTROL)
W B INSERT P
(3/9,7/9)
B-SS3280<AEP>-BK.-P1
11-20
A
B
C
D
11-20
E
F
G
H
BK (2/9)
BK (2/9)
G
R338
910
:RN-CP
Q350
2SC3545
Y/G-Y MIX
TP302
R344
2.2k
:CHIP
G
-0.3
VCC
CONT1 IN2
OUT1 CONT2
OUT2
1
2
3
0.8
Q306
2SC3545
G-Y MATRIX AMP
0.5
-1.7
R340
1k
:RN-CP
R352
680
:RN-CP
0.1
Q308
2SA1037K R123
G-Y BUFFER 1k
:CHIP
1.2
0.8
Q309
2SA1037K
G BUFFER
R351
9.1k
:RN-CP
R350
300
:RN-CP
1.4
5 Z0
3 Z1
1.2
Q353
2SA1462
G CLAMP
4.5
1.4
C
R366
1k
:RN-CP
R359
100
:CHIP
R349
1.5k
:CHIP
1.4
0.7
9
R357
2.2k
:CHIP
R353
820
:CHIP
Q352
2SC3545
G CLAMP
4
Z
C331
4p
CH:CHIP
C328
2.2
16V
F:CHIP
R337 C409
2.2
10k
:RN-CP 16V
F:CHIP
-5V
1.9
-0.8
R342
2.2k
:CHIP
2.2 -0.2
-5V
Q108
2SC2412K
Y BUFFER
R343
100
:CHIP
-0.7
R332 TH300
4.7k
:RN-CP
4
-1.0
4.6
-1.7
R333
2k
:RN-CP
1.4
R370
100
:CHIP
R369
1.2k
:CHIP
R363
6.8k
:RN-CP
R329
33k
:RN-CP
C310
0.01
F:CHIP
1
2
3
R368
47k
:RN-CP
R358
330k
:RN-CP
R336
33k
:RN-CP
-2.1
7
12 X0
0.913
X1
4
0
C352
0.047
25V
B:CHIP
VCC
0.9
2 Y0
1 Y1
0.1
X 14
0
A VEE GND
C353
0.01
B:CHIP
-5V
X
10
R377
2.2k
:CHIP
0.3
0.3
-0.4
9
C356
100
6.3V
:HT-CP
A/C GREEN
(7/9)
C
R376
2.2k
:CHIP
-5V
2
BLACK SAMPLING P
(1/9,3/9,4/9,5/9,6/9,7/9)
14
A VEE GND
6 11 7 8
-5V
WHITE INSERT P(1/9,7/9)
IC507
TC4W53FU
B CLAMP
+5V
4
Z
0.1
:CHIP
IC311(2/2)
TL082CPS
B
VCC
12 X0
0.1
13 X1
R488 1.0
220
1.0
B OUT (1/9)
0.3
16
R487
220
1
0.2
5 Z0
3 Z1
0.3
G 0.9
Q374
2SC2412K
G BUFFER
+5V
4 0.1 :CHIP
R361 C350 R367 C351
10k 0.01 11k 0.01
:RN-CP F:CHIP :RN-CP F:CHIP
Y 15
0.9
IC310(3/3)
MC74HC4053FEL
G/B SELECT
IC313(1/3)
MC74HC4053FEL
G REF SW
7
3
2
G 100IRE (9/9)
C330
2.2
16V
F:CHIP
1
G(3/9)
Q375
2SC2412K
G BUFFER
B
C354
0.01
F:CHIP
1.0
C432
47
6.3V
:HT-CP
TP304
7
6 11 7 8
5.2
4
C329
2.2
16V
F:CHIP
8
6
5
R360
180k
:RN-CP
R334
33k
:RN-CP
R375
100
:RN-CP
16
8
5
0.1 6
R373
10k
:CHIP
R-Y GAIN (9/9)
C311
0.01
F:CHIP
5
IC311(1/2)
TL082CPS
BUFFER
0.1
R330
33k
:RN-CP
6
0.1
G SET UP (9/9)
B-Y GAIN(9/9)
7
+5V
G
IC310(2/3)
MC74HC4053FEL
PULSE INSERT
-5V
C431
47
6.3V
:HT-CP
R335
68k
:RN-CP
0.9
Q354
2SA1462
G CLAMP
0.2
+5V
R331
68k
:RN-CP
8
0.2
R362
1M
:CHIP
0.1
G
C357 C430
100
C355 100
0.01 6.3V 6.3V
F:CHIP :HT-CP :HT-CP
IC306(1/2) R374
IC310(1/3)
TL082CPS
MC74HC4053FEL
180
:RN-CP HALF BLK SWITCH
G CLAMP
0.2
5
GND
6
IN1
7
R372
1k
:CHIP
R365
820
:CHIP
IC304(2/3)
MC74HC4053FEL 6
RGB SW
TP303
5
8
IC307
TC4W53FU
G CLAMP
+5V
0.1
IC305
CXA1211M
G-Y MATRIX AMP
Q351
2SC3545
Y/G-Y MIX
R354
680
:RN-CP
0.9
2.4
0.5
Q307
R345
1k
2SA1462
G-Y MATRIX AMP :CHIP
VDD
CH0
CH1
ADR
R346
10k
:RN-CP
+5V
5V
COM
INH
VEE
VSS
Y/G OUT (1/9)
IC510(1/3)
IC506(1/2) R568
MC74HC4053FEL
TL082CPS 180
B CLAMP :RN-CP HALF BLK SWITCH
C547 C630
C545 100 100
0.01 6.3V 6.3V
F:CHIP :HT-CP:HT-CP
+5V
-5V
C549
100
6.3V
:HT-CP
PB OUT(1/9)
0.5
R542
680
:RN-CP
R541
9.1k
:RN-CP
-0.2
R540
270
:RN-CP
R532
1k
:CHIP
2.8
-0.6
C528
2.2
16V
F:CHIP
R543
820
:CHIP
9
IC504(2/3)
MC74HC4053FEL
RGB SW
0.8
Q506
2SA1037K
R547 B BUFFER
2.2k
:CHIP
1.5
5 Z0
3 Z1
C
2.8
0 9
4.5
B
Q542
TP503 2SC3545
B CLAMP
R556
1k
:RN-CP
R546 R549
1.5k 100
:CHIP :CHIP
1.5
0.7
C531
4p
CH:CHIP
Q543
2SA1462
B CLAMP
8
B
0.9
1.5
4
Z
0
0.9
TP502
1.5
3.5
R562
1k
:CHIP
R555
820
:CHIP
0.2
R560
100
:CHIP
0.2
Q544
2SA1462
B CLAMP
R559
1.2k
:CHIP
R553
6.8k
:RN-CP
7
6
R552
1M
:CHIP
1
2
16
3
5
6
0
7 -1.7 12
X0
0.913
X1
4
0
0
C542
C543
0.047
0.01
25V
B:CHIP
B:CHIP
R565
10k
:CHIP
4
VCC
A VEE GND
6 11 7 8
5.2
-5V
IC511(1/2)
TL082CPS
BUFFER
+5V
Y
2
1
15
R548
330k
:RN-CP
Y0
Y1
B
Y
IC104(3/3)
MC74HC4053FEL
2
Y0
Y1
Y
-0.2
15
R140
300
:RN-CP
R122
1k
:CHIP
2.8
-0.7
R141
9.1k
:RN-CP
0.5
3.4
R142
TP101 680
:RN-CP
C128
2.2
16V
F:CHIP
R143
820
:CHIP
0.8
Q106
2SA1037K
R BUFFER
R147
2.2k
:CHIP
1.4
5 Z0
3 Z1
C
2.8
0 9
R
4
Z
1.4
Z0
Z1
Z
4
0
9
A VEE GND
R149
R146 100
1.5k :CHIP
:CHIP
Q143
2SA1462
R CLAMP
R153
6.8k
:RN-CP
R
8
0.2
R156
1k
:RN-CP
0.7
C131
4p
CH:CHIP
R152
1M
:CHIP
4.5
Q142
TP103 2SC3545
R CLAMP
1.5
0.1
0.9
0.1
R162
1k
:CHIP
R155
820
:CHIP
12
IC104(2/3)
MC74HC4053FEL
RGB SW
5
3
14
7
6
R160
100
:CHIP
0.9
0.2
1
Q144
2SA1462
R CLAMP0.1
R159
1.2k
:CHIP
2
3
C147 C230
100
C145 100
0.01 6.3V 6.3V
F:CHIP :HT-CP :HT-CP
IC110(1/3)
IC106(1/2) R164
MC74HC4053FEL
TL082CPS
180
:RN-CP HALF BLK SWITCH
BUFFER
5
16
0
0.9
7
12 X0
-1.8 13 X1
4
0
+5V
X
14
6 11 7 8
5.2
R165
100
:RN-CP
4
R
13
TP104
VCC
A VEE GND
C142
C143
0.01
0.047
25V
B:CHIP
B:CHIP
R163
10k
:CHIP
4
IC110(2/3)
MC74HC4053FEL
PULSE INSERT
8
5
0.1 6
VDD
CH0
CH1
ADR
11
PR OUT(1/9)
12
TP102
IC510(3/3)
MC74HC4053FEL
C
IC107
TC4W53FU
R CLAMP
1.4
3
C548
100
6.3V
:HT-CP
-5V
COM
INH
VEE
VSS
Q140
2SC3545
Y/PR MIX
Q107
2SC2412K
PR BUFFER
A/C BLUE
(7/9)
R570
2.2k
:CHIP
R551 C540 R557 C541
10k 0.01 11k
0.01
:RN-CP F:CHIP :RN-CP F:CHIP
+5V
TP301
-0.4
R576
2.2k
:CHIP
6 11 7 8
TL082CPS
BUFFER
R121
2.2k
:CHIP
X
:CHIP
1
R
4
IC513(1/3)
MC74HC4053FEL
B REF SW
VCC
12 X0
13 X1
R688 0.9
220
1.0 IC511(2/2)
R OUT(1/9)
0.2
R571
2.2k
:CHIP
16
R687
220
:CHIP
4 0
3
2
-5V
Q141
R144
680 2SC3545
:RN-CP Y/PR MIX
C530
2.2
16V
F:CHIP
7
1.0
B 100IRE(9/9)
C632
47
6.3V
:HT-CP
10
10
0.9
0.2
+5V
C529
2.2
16V
F:CHIP
0
R550
180k
:RN-CP
B
5
Q567
2SC2412K
B BUFFER
+5V
8
6
5
0.1
15
6
0.2
C546
100
6.3V
:HT-CP
C544
0.01
F:CHIP
0.9
15 R
2
Y0
Y
1
Y1
0.9
B
0.1
10
0.5
Q165
2SC2412K
B BUFFER
IC110(3/3)
MC74HC4053FEL
B/R SELECT
0.3
5 Z0
3 Z1
C
0.3
9
5.3
0.9
0.3
R167
2.2k
:CHIP
Z
R(3/9)
Q164
2SC2412K
R BUFFER
4
0.3
-0.4
A/C RED
(7/9)
R166
2.2k
:CHIP
B
IC111(1/2)
TL082CPS
BUFFER
8 7 11 6
(2/9)
BK
G-Y MATRIX, Y PB/PR MIX
1.0
3
2
R 100IRE (9/9)
C232
47
6.3V
:HT-CP
R288
220
1 :CHIP
1.0 IC111(2/2)
TL082CPS
BUFFER
X
5.2
14
0.1
-5V
IC509
TC7S00FU
CHAR BLK INSERT
5.2
5.2
5.3
5
5
VCC
1
VDD
CH0
CH1
ADR
8
COM
INH
VEE
VSS
2
VCC
12 X0
13 X1
1.0
R566
100k
:CHIP
4.8
CHAR BLK(9/9)
0.1
R567
100k
:CHIP
5.2
GND
4
R150
180k
:RN-CP
GND VEE A
16
R287
220
40.1 :CHIP
IC508
TC4W53FU
CHAR BLK SW
R564
100
:CHIP
3
0
R563
1k
:CHIP
7
R SET UP (9/9)
12
13
IC113(1/3)
MC74HC4053FEL
R REF SW
7
6
X0
X1
8
6
5
0.5
5
VCC
14 X
R148
330k
:RN-CP
C130
2.2
16V
F:CHIP
1
C231
47
6.3V
:HT-CP
+5V
+5V
C129
2.2
16V
F:CHIP
2
+5V
IC104(1/3)
MC74HC4053FEL
16
R158
47k
:RN-CP
A VEE GND
6 11 7 8
0.2
RGB
≠≠≠≠≠≠
≠≠≠≠≠
SW (1/9,9/9)
C146
100
6.3V
:HT-CP
C144
0.01
F:CHIP
-5V
10
3
1
4
2 Y0
1 Y1
R558
47k
:RN-CP
B SET UP (9/9)
IC504(3/3)
MC74HC4053FEL
B (3/9)
4
0.2
IC304(3/3)
MC74HC4053FEL
B
1 3
2
0.1
-5V
C631
47
6.3V
:HT-CP
TP504
0.9
15 B
2 Y0
Y
1 Y1
0.9
B
0.1
0.5 10
14
X
Q568
IMX2
B BUFFER
10
IC510(2/3)
R569
100 MC74HC4053FEL
:RN-CP PULSE INSERT
8
5
VDD
CH0
CH1
ADR
Q540
2SC3545
Y/PB MIX
Q507
2SC2412K
PB BUFFER
9
COM
INH
VEE
VSS
TP501
R531
2.2k
:CHIP
0.1
+5V
R544
Q541
680 2SC3545
:RN-CP Y/PB
MIX
8
CH BACK H/B(9/9)
BLUE
≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠
ONLY (9/9)
W≠≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠≠
B INSERT P- (7/9)
R151 C140 R157 C141
10k 0.01 11k
0.01
:RN-CP F:CHIP :RN-CP F:CHIP
-5V
SIGNAL PROCESSOR, BLUE ONLY SW
B-SS3280<AEP>-BK.-P2
11-21
A
B
C
D
11-21
E
F
G
H
BK (3/9)
IC331
TC7S32FU
CHAR G
0.4
1
VCC
0.9
1.1
0.9
5.0
5.2
0
4
5
6
7
8
0.9
G
R472
100
:CHIP
2
C421
22
6.3V
:HT-CP
VCC
0.4
0.6
4
0.8
0.1 10
C560
0.01
F:CHIP
C571
0.047
B:CHIP
JR501
Z0
Z1
4
Z
C
0.1 9
C561
0.01
F:CHIP
0.9
1.1
0.8
5.0
5.2
I.C.
NC
C.I.
NC
OUT
0
2
3
4
5
6
7
8
1
2
3
4
6
7
5
2
D600
MA111
DC SHIFT
R598
100
:CHIP
0.9
-5V
-2.5
-2.5
R609
100 :CHIP
R672
100
:CHIP
B
16
0.9
Q600
2SC3545
B BUFFER
TP505
0.2
R673
10k
:CHIP
R600
100 :CHIP
R599
1.2k
:RN-CP
R597
15k
:RN-CP
-8.1
R602
2k
:RN-CP
C575
47
R596 C577
16V
33k
2.2
:TA-CP :RN-CP 16V
F:CHIP
R603
2.7k
:RN-CPR606
12k
:RN-CP
R601
3.9k
:RN-CP
C578
2.2
16V
F:CHIP
R674
220
:CHIP
R188
1k
:CHIP
R580
22k
:RN-CP
0.4
VCC
JR101
C168
0.047
B:CHIP
C160
0.01
F:CHIP
C169
0.047
B:CHIP
0.9
1.1
0.8
5.0
5.2
R620
10k
:RN-CP
R615
100
:CHIP
3 5
R636
10k
:CHIP
C585
0.047
25V
B:CHIP
C582 R617
0.01 4.7k
F:CHIP :RN-CP
R619
2.0k
:RN-CP
-5V
C622
0.01
F:CHIP
-10.8
-12V
-12V
2
3
4
5
6
7
8
2
3
4
5
I.C.
C.I.
NC
NC
VEE
1
6
7
R194
100
:CHIP
0.2
0.9
R
0.9
0.2
R273
10k
:CHIP
R174
220
:CHIP
14
Q200
2SC3545
R BUFFER
R193
15k
:RN-CP
TP105 C172
47
16V
:TA-CP
R195
1.2k
:RN-CP
R192
33k C174
:RN-CP 2.2
16V
F:CHIP
2
D200
MA111
DC SHIFT
4.5
Q174
-1.9
2SC3545
1 3
R DRIVE AMP
Q172
4 IMX2
R226
R DRIVE AMP
R205
100
:CHIP
-7.5
-2.5
-2.5
6 5
1 3
2
R196
100 :CHIP
R198
2k
:RN-CP
R197
3.9k
:RN-CP
-8.2
R199
2.7k
:RN-CP R202
12k
:RN-CP
C175
2.2
16V
F:CHIP
R223
1.2k
:RN-CP
D201
RD6.8M-T1B1
R DRIVE AMP
0
C
B
A
X3
X0
X1
X2
VCC
1
R272
100
:CHIP
R171
15k
:RN-CP
R612
680
:RN-CP
8
NC
C161
0.01
F:CHIP
OUT
3
0.9
C167
2.2
16V
F:CHIP
IC116
MC74HC4051FEL
PULSE INSERT
-5V
BIAS REF(9/9)
IC518(1/2)
TL082CPS
B DRIVE AMP
6 11 7 8
0.1
R633
2.2k
:CHIP
4
-0.5
BLACK SAMPLING P
(1/9,2/9,4/9,5/9,6/9,7/9)
WHITE SAMPLING P
(1/9,4/9,5/9,6/9,7/9)
2
3
R631 0.6
2.2k
:CHIP
2
C
0.1 9
1
0.9 3
-5V
5
R629
2.2k
:RN-CP
DR(4/9)
Q175
Q176
2SA1462
2SC3545
R DRIVE AMP R DRIVE AMP
-10.5
OUT
NC
-0.6
0.8
Z
-8.3
R168
1k
:CHIP
0.1 10
Z0
Z1
S.I.
BIAS
0.5
B
0.8
R184
1.2k
:CHIP
5
3
7
G.A.
G.A.
6
5
0
0
14 13 12 11 10 9
S.I.
15
GND
R182 0.8
5.6k
:CHIP
Y
VEE
C163
8p
CH:CHIP
Y0
Y1
-10.8
-2.5
16 15 14 13 12 11 10 9
ENABLE
R177 -0.3
2.0k
:RN-CP
R178
3.0k
:RN-CP
2
1
1.5
0.9
7
A VEE GND
R618
2.2k
:RN-CP
-8.2
4 -10.2
R
-7.6
-0.5
R181
1.2k
:RN-CP
0.6
2
C640
0.01
F:CHIP
-0.7 -2.5
-8.3
R (2/9)
R169
1.5k
:CHIP
1.5
Q167
2SC3545
CONT.BRT CONTROL
IC114(2/2)
TL082CPS
BRT CONTROL
C166
IC114(1/2)
0.68
16V
TL082CPS
F:CHIP CONTRAST CONTROL
R176
R172
10k
1k
:CHIP
4
2
:CHIP
X5
4
R183
100
:CHIP
IC113(3/3)
MC74HC4053FEL
SWITCH
X7
3
R179
100
:CHIP
C165
0.22
25V
F:CHIP
R175
4.7k
:CHIP
IC113(2/3)
R MC74HC4053FEL
Q573
IMX2
B DRIVE AMP
0
6
5
1.2
-7.5
6 5
1 3
X0
X1
X 14
R
X
2
0.3
R173
100
:CHIP 0.4
4.5
R625
1.5k
:RN-CP
IC115
NJM1496M
R DRIVE AMP
R
R180
1.8k
:RN-CP
4
1.2
0
VCC
12
13
-0.7
R614
680
:RN-CP
5.2
X6
1
R
-0.3
-0.9
4.5
GND
X4
OUT
VEE
DC
GAIN
GND
5
GND
C1004
2.2
16V
F:CHIP
6
IN
VCC
7
R189
100
:CHIP
Q168
2SA1462
CONT.BRT CONTROL
C162
82p
CH:CHIP
Q574
IMX2
B DRIVE AMP
1 3
R616
100 :CHIP
5.6k
:RN-CP
C586
0.022
F:CHIP
16
R632
100
:CHIP
4.5
IC131
TC7S32FU
CHAR R
1
0.4
5.2
0.9
R
0.5
8
CHAR R
(9/9)
Q169
2SC3545
CONT.BRT CONTROL
Q166
2SC2412K
BRT BUFFER
R626
100
:CHIP
IC517(1/3)
MC74HC4053FEL
B DRIVE AMP
+5V
C621
2.2
16V
F:CHIP
4
+5V
DB(6/9)
+5V
B DRV CONT(6/9)
0.9
IC506(2/2)
TL082CPS
BUFFER
IC112
CXA1521M
CONT.BRT CONTROL
6 5
R611
820
R608 :RN-CP
6.2k
-8.7
:RN-CP
-12V
1
0.9
C570
0.01
F:CHIP
-12V
5
CH LEVEL (9/9)
R627
1.2k
:RN-CP
Q577
-1.9
2SC3545
1 3
B DRIVE AMP
Q575
4 IMX2
R630
2
W B INSERT P(1/9,7/9)
BRT(7/9)
C392
0.047
25V
B:CHIP
C422
0.01
F:CHIP
-12V
B DRIVE AMP
-7.6
-5V
2
3
R425
2.0k
:RN-CP
4.5
I.C.
NC
C.I.
NC
VEE
C
B
A
X3
X0
X1
1
OUT
3
-0.4
0.9
C569
2.2
16V
F:CHIP
C572
0.047
B:CHIP
X2
VCC
IC516
MC74HC4051FEL
PULSE INSERT
1
0.2
R581
33k
:RN-CP
R442
10k
:CHIP
4
R574
1k
:CHIP
2
0.9 3
-10.5
NC
-0.6
B
0.8
R588
1.2k
:CHIP
5
3
OUT
7
R423
C389 4.7k
0.01 :RN-CP
F:CHIP
D601
RD6.8M-T1B1
B DRIVE AMP
8
NC
0
R572
1k
:CHIP
8
6
5
0
S.I.
BIAS
15
14 13 12 11 10 9
-8.3
Y
IC318(1/2)
TL082CPS
G DRIVE AMP
6 11 7 8
0.1
R439
2.2k
:CHIP
Q578
Q579
2SA1462
2SC3545
B DRIVE AMP B DRIVE AMP
-2.5
16 15 14 13 12 11 10 9
G.A.
G.A.
Y0
Y1
R577
4.7k
:CHIP
R437 0.7
2.2k
:CHIP
-5V
R426
10k
:RN-CP
-8.1
4 -10.2
0.9
7
A VEE GND
R435
2.2k
:RN-CP
R424
2.2k
:RN-CP
B
GND
R586 0.8
5.6k
:CHIP
C563
8p
CH:CHIP
2
1
1.5
1 3
2
C440
R421
0.01
100
F:CHIP -10.8
:CHIP
R418 6 5
-10.8
680
:RN-CP
-0.7 -2.5
VEE
R579 -0.3
2.0k
:RN-CP
R582
3.0k
:RN-CP
SWITCH
R587
100
:CHIP
IC514(1/2)
TL082CPS
CONTRAST CONTROL
ENABLE
Q570
2SC3545
CONT.BRT CONTROL
R573
1.5k
:CHIP
B (2/9)
R583
100
:CHIP1.5
R585
1.2k
:RN-CP
C568
0.68
16V
F:CHIP
R578
10k
:CHIP
IC513(3/3)
MC74HC4053FEL
SWITCH
IC514(2/2)
TL082CPS
BRT CONTROL
X5
4
0.2
B MC74HC4053FEL
Q380
IMX2
G DRIVE AMP
-8.8
0
6
5
B
X7
3
R575
100
:CHIP 0.4
C385
2.2
16V
F:CHIP
6 5
R417
820
:RN-CP
X0
X1
-7.5
IC515
NJM1496M
B DRIVE AMP
B
C567
0.22
25V
F:CHIP
IC513(2/3)
4.5
R407
3.9k
:RN-CP
R414
6.2k
:RN-CP
X 14
0.7
-0.7
R420
680
:RN-CP
5.2
X
2
B
GND
X6
1
-0.3
-0.9
5.2
R593
100
:CHIP
X4
OUT
VEE
DC
GAIN
GND
5
GND
C1020
2.2
16V
F:CHIP
6
IN
3
7
VCC
8
CHAR B
(9/9)
R584
1.8k
:RN-CP
4.5
C382
R402 C384
47
33k
16V
2.2
:TA-CP :RN-CP 16V
F:CHIP
R409
2.7k
:RN-CP R412
12k
:RN-CP
1.4
VCC
2
1
C562
82p
CH:CHIP
0.4
R408
2k
:RN-CP
1.3
0
12
13
+5V
Q571
2SA1462
CONT.BRT CONTROL
B
0.6
2
-8.2
R436
G DRIVE AMP 5.6k
:RN-CP
6 5
Q381
IMX2
G DRIVE AMP
1 3
R422 R431
1.5k
100
4
:CHIP :RN-CP
C393
0.022
F:CHIP
16
R438
100
:CHIP
4.5
IC531
TC7S32FU
0.4 CHAR B
0.9
+5V
R403
15k
:RN-CP
-2.5
-2.5
R415
100 :CHIP
R406
100 :CHIP
-7.6
IC306(2/2)
TL082CPS
BUFFER
Q572
2SC3545
CONT.BRT CONTROL
Q569
2SC2412K
BRT BUFFER
7
-1.9
1 3
Q382
4 IMX2
R432
100
:CHIP
4.5
Q384
2SC3545
G DRIVE AMP
G DRV CONT(5/9)
R592
1k
:CHIP
IC512
CXA1521M
CONT.BRT CONTROL
6
5
-12V
1.1
R386
22k
:RN-CP
4
1
1.1
C377
0.01
F:CHIP
3
R405
1.2k
:RN-CP
15
Q400
2SC3545
G BUFFER TP305
R473
0.2
10k
:CHIP
R474
220
:CHIP
2
3
IC317(1/3)
MC74HC4053FEL
G DRIVE AMP
5
R387
33k
:RN-CP
2
R404
100
:CHIP
0.2
0.9
-5V
DRIVE REF(9/9)
1
NC
3
-8.3
VEE
C
B
A
X3
X0
X1
X2
2
2
D400
MA111
DC SHIFT
-7.5
-5V
-5V
1
8
-10.5
OUT
NC
-0.6
0.01
F:CHIP
C376
2.2
16V
F:CHIP
S.I.
BIAS
3
4
-0.4 C361
0.9
C379
0.047
B:CHIP
IC316
MC74HC4051FEL
PULSE INSERT
1
-7.6
C
0.1 9
C360
0.01
F:CHIP
C378
0.047
B:CHIP
JR301
0.9
R380
1k
:CHIP
2
0.9 3
G.A.
G.A.
R378
1k
:CHIP
0.1 10
4
Z
S.I.
4 0.5
B
0.9
Z0
Z1
8.3
5
3
7
GND
R394
1.2k
:CHIP
8
6
5
0
S.I.
-0.4
C363
8p
CH:CHIP
Y 15
0
Y0
Y1
14 13 12 11 10 9
R433
1.2k
:RN-CP
D401
RD6.8M-T1B1
G DRIVE AMP
-2.5
16 15 14 13 12 11 10 9
-8.3
0.3
G(2/9)
R392
5.6k
:CHIP
R385 -0.3
2.0k
:RN-CP
R388
3.0k
:RN-CP
R379
1.5k
:CHIP
2
1
0.9
1.5
R384
10k
:CHIP
+5V
G
VEE
4
R383
4.7k
:CHIP
DG (5/9)
Q385
Q386
2SA1462
2SC3545
G DRIVE AMP G DRIVE AMP
-0.7 -2.5
ENABLE
3
Q377
2SC3545
CONT.BRT CONTROL
G
C375
0.68
IC314(1/2)
16V
TL082CPS
F:CHIP CONTRAST
CONTROL
X5
VEE
2
R389
100
:CHIP
1.5
R391
1.2k
:RN-CP
R393
100
:CHIP
IC313(3/3)
MC74HC4053FEL
SWITCH
IC314(2/2)
TL082CPS
BRT CONTROL
X7
OUT
GAIN
1
G
G
C374
0.22
25V
F:CHIP
IC313(2/3)
MC74HC4053FEL
SWITCH
4.5
R381
100
:CHIP 0.4
-0.9
GND
DC
5
IN
C1011
2.2
16V
F:CHIP
6
GND
7
VCC
8
R390
1.8k
:RN-CP
4.5
X
-0.3
+5V
VCC
C362
82p
CH:CHIP
0.4
G
IC315
NJM1496M
G DRIVE AMP
5.2
X6
G
0.5
R399
100
:CHIP
Q378
Q379
2SA1462
2SC3545
CONT.BRT CONTROL CONT.BRT CONTROL
GND
X4
Q376
IC312
2SC2412K
CXA1521M
CONT.BRT CONTROL BRT BUFFER
+5V
5.2
0.9
5V
2
CHAR G
(9/9)
5
R398
1k
:CHIP
1
BK (3/9)
R204
6.2k
:RN-CP
R207
820
:RN-CP
Q170
IMX2
R DRIVE AMP
-8.8
2
-10.8
R208
680
:RN-CP
R221
1.5k
:RN-CP
IC117(1/3)
MC74HC4053FEL
R DRIVE AMP
R222
100
:CHIP
R228
100
:CHIP
4.5
1.3
VCC
12
13
1.3
X0
X1
R211
100
:CHIP
6 5
F:CHIP
0
14 0
6
7
5
A VEE GND
R225
2.2k
:RN-CP
R216
10k
:RN-CP
C179 R213
0.01 4.7k
F:CHIP :RN-CP
R215
2.0k
:RN-CP
-10.8
X
0.6
-0.7
R214
2.2k
:RN-CP
-8.2
4 -10.2
C183
0.022
16
R227 0.6
2.2k
:CHIP
0.9
IC118(1/2)
TL082CPS
R DRIVE AMP
6 11 7 8
0.1
R229
2.2k
:CHIP
R232
10k
:CHIP
C182
0.047
25V
B:CHIP
-7.5
6 5
1 3
C240
0.01
F:CHIP
Q171
IMX2
R DRIVE AMP
R212
100
4
:CHIP
5.6k
:RN-CP
+5V
-5V
C222
0.01
F:CHIP
1
0.2
0.2
IC106(2/2)
TL082CPS
BUFFER
C154
22
6.3V
:HT-CP
R210
680
:RN-CP
-12V
CONT(7/9)
W&D.P(7/9)
BIAS P (7/9)
R DRV CONT (4/9)
-12V
-12V
BK
(3/9)
(RGB SIGNAL PROCESSING,RGB DRIVE)
C164 R170
0.01 1.3k
F:CHIP :RN-CP
B-SS3280<AEP>-BK.-P3
11-22
A
B
C
D
11-22
E
F
G
H
BK (4/9)
BK (4/9)
120V
1
Z
R236
82k
:CHIP
C
9
1
0.1
124.6
70.1
VOC
72.3
VOF
69.0
S
VCN
VDDH
5.2
0
2
3
4
5
6
7
8
58.3
R
C241
2p
CH:CHIP
0
R242
10k
:CHIP
5.3
R243
7.5k
:RN-CP
Q190
DTC144EKA
R CUTOFF SW
R CUTOFF(9/9)
TP107
C192
0.01
B:CHIP
R248 R252
70.1
39k
39k
1/2W :CHIP
:RN
D166
RD22M-B3
PROTECTOR
4
R230
10k
:CHIP
5.2
R257
100
1/2W
:RC
9
R
R241
1k
:RN-CP
C196
10
160V
:HT
C194
0.01
200V
D168
HSM83-TL
PROTECTOR
17
1 -0.3 0
VIDEO TIMING P
(5/9,6/9,7/9)
Q178
2SK520
VIDEO OUT
SWITCHING
18
4
C187
0.01
F:CHIP
-5V
Q177
2SK520
VIDEO OUT
SWITCHING
0.6
8
-0.3 2
3
+5V
S
R237
4.7k
:CHIP
0.6
5 Z0
3 Z1
IOM
IC118(2/2)
TL082CPS
AMP
GND
IC117(3/3)
MC74HC4053FEL
CUTOFF SW
TP106
VIN
R
DR(3/9)
VDDL
+5V
VIP
5V
+120V
IC119
TDA6101Q/N3
VIDEO AMP
R
1
2
3
4
D167
HSM83-TL
PROTECTOR
70.1
IC129(1/2)
LM393PS
KR
NC
NC
GND
TO
C BOARD
CN504
R186
10k
:CHIP
-5V
R244
390k
:RN-CP
R253
C191 67.8 68k
:CHIP R255
100p
10k
CH:CHIP
:CHIP
Q179
2SC1654
0
SWITCH
R254
1.8k
:CHIP
R258
100k
:RN-CP
R247
5.6k
:RN-CP
-5V
5
6
7
CN2
4P
RED
:S-MICRO
R DRIVE COMP
(9/9)
BIAS & DRIVE P
(5/9,6/9,7/9)
8
-5.2
1
3
2 -3.9
R185
10k
:CHIP
IC117(2/3)
MC74HC4053FEL
SWITCH
IC124(1/3)
IC129(2/2) MC74HC4053FEL
LM393PS
SWITCH
COMPARATOR
-3.9
4 Z
-0.4
2
1
5
3
Z0
Z1
-3.9
-0.4
0
Y
-0.5
15
R DRV CONT
(3/9)
B
C
4
Y0
Y1
10
2
0
9
≠ SW
IK/V
(5/9,6/9,7/9)
-12V
-5V
-12V
R245
220
:CHIP
G2 R(7/9)
C200
C198 2.2 C202 C204
0.01 16V 0.01 0.01
F:CHIP F:CHIP F:CHIP F:CHIP
+5V
+5V
IC124(2/3)
MC74HC4053FEL
R BIAS CONTROL
C190
0.22
25V
F:CHIP
R238
10k
0.4 :CHIP
4.2 12 Y0
13 Y1
Y 14
B
0 11
C188
0.1
25V
F:CHIP
BIAS SAMPLING P
(5/9,6/9,7/9)
0.4
-2.4
2
3
0.4
C220
270p
CH:CHIP
D165
MA111
PROTECTOR
IC122(1/2)
TL082CPS
R251
BIAS CLAMP
R246 68k
5.6k :RN-CP
CONTROL
:RN-CP
-1.5
6
1
IC122(2/2)
TL082CPS
R BIAS CLAMP
CONTROL
C189
0.01
F:CHIP
D164
MA111
PROTECTOR
-2.0R249
5.6k
VCC
7
15 X
X0
X1
44.2 4.2
:RN-CP
2.2
16V
F:CHIP
R256
10k
2 :CHIP
8
16
R250
220
:CHIP
8
6
5
7
0.15
R259 IC123(2/2)
TL082CPS
10k
:CHIP R BIAS CLAMP
1
0
GND VEE A
2
0 3
1
0
4
R BIAS IK (9/9)
R239
6.8k
:RN-CP
6
5
0.1
C199
0.01
C201
0.01
-4.0
-1.1
25V
F:CHIP
C203
0.01
C171
0.01
F:CHIP
R187
15k
:RN-CP
R DRIVE IK (9/9)
IC127(2/2)
TL082CPS
R DRIVE IK
CONTROL
R191
10k
:RN-CP
6
0 5
+5V
3
7
B
0 11 C170
0.33
IC123(1/2) F:CHIP F:CHIP F:CHIP F:CHIP
TL082CPS
R BIAS CLAMP
BIAS CLAMP P
(5/9,6/9,7/9)
R190
10k
:CHIP0.1
Y
DRIVE SAMPLING P
(5/9,6/9,7/9)
C197
0.01
R240
5.6k
:RN-CP
C173
0.47
25V
F:CHIP
14
12 Y0
13 Y1
0
C193
0.047
F:CHIP
8 70 10 6
-5V
IC126(2/3)
MC74HC4053FEL
SWITCH
IC124(3/3)
MC74HC4053FEL
R IK CLAMP C195
7
-1.1
IC128(1/2)
NJM4558M
R DRIVE IK AMP
+5V
IC126(3/3)
MC74HC4053FEL
SWITCH
IC121(1/2)
TL082CPS
R DRIVE V
CONTROL
-0.6
3
2
2
1
1
4
16
R217
10k
:CHIP
R219
220
:CHIP
8
IC126(1/3)
MC74HC4053FEL
SWITCH
C181
0.01
B:CHIP
Z 15
0
Z0
Z1
C
-0.6
-0.6
0.1 10
R224
10k
:RN-CP
C180
0.01
F:CHIP
6
0 5
-0.8
VCC
-2.4
7
5
3
-0.6
IC121(2/2)
TL082CPS
R DRIVE V
CONTROL
X
WHITE SAMPLING P
(1/9,3/9,5/9,6/9,7/9)
R201
10k
:CHIP
2
8
-0.4
1
4
A VEE GND
BLACK SAMPLING P
(1/9,2/9,3/9,5/9,6/9,7/9)
-5V
X0
X1
C176
0.047
25V
B:CHIP
-0.8
C178
0.01
F:CHIP
4
3
-0.8
4 IC127(1/2)
TL082CPS
R DRIVE V
CONTROL
6 9 7 8
0.1
C177
0.01
F:CHIP
-5V
0
R DRIVE V(9/9)
R206
15k
:RN-CP
R203
4.3k
:RN-CP
8
2
3
IC128(2/2)
NJM4558M
R DRIVE AMP
1
4
-0.8
(4/9)
BK
R VIDEO OUT
R DRIVE IK/V CONTROL
B-SS3280<AEP>-BK.-P4
5
11-23
A
B
C
D
11-23
E
F
G
H
BK (5/9)
BK (5/9)
120V
1
+120V
IC319
TDA6101Q/N3
VIDEO AMP
+5V
5V
5
6
7
8
R467
100
1/2W
:RC
9
70.1
0
G
C402
0.01
B:CHIP
R458 R462
71.4
39k
39k
1/2W :CHIP
:RN
D376
RD22M-B3
PROTECTOR
G
-0.3
4
S
IOM
4
0.4
VDDH
124.6
VCN
71.4
VOC
73.5
VOF
70.3
5.2
0
GND
3
TP307
R451
1k
:RN-CP
C397
0.01
F:CHIP
-5V
-5V
2
19
C451
2p CH:CHIP
CN3
4P
WHT
:S-MICRO
G
+5V
S
1
3
R446
82k
:CHIP
1
20
4
0.7
C
9
8
R447
2
4.7k
:RN-CP -0.3
Z
VIN
0.7
5 Z0
3 Z1
VDDL
IC317(3/3)
MC74HC4053FEL
CUTOFF SW
TP306
IC318(2/2)
TL082CPS
AMP
VIP
G
DG(3/9)
C406
10
160V
:HT
C404
0.01
200V
D378
HSM83-TL
PROTECTOR
Q387
Q388
2SK520
2SK520
VIDEO OUT VIDEO OUT
SWITCHING SWITCHING
D377
HSM83-TL
PROTECTOR
71.4
KG
NC
NC
GND
1
2
3
4
R440
10k
:CHIP
TO
C BOARD
CN505
5.2
5
6
7
-5V
0
VIDEO TIMING P
(4/9,6/9,7/9)
G CUTOFF(9/9)
5.2
R452
10k
:CHIP
Q390
DTC144EKA
CUTOFF SW
2
R454
390k
:RN-CP
R453
7.5k
:RN-CP
C401 69.3
100p
CH:CHIP
R468
100k
:RN-CP
R457
5.6k
:RN-CP
R463
68k
:CHIP
Q389
2SC1654
SWITCH
IC329(1/2)
LM393PS
R465
10k
:CHIP
IC329(2/2)
LM393PS
COMPARATOR
BIAS & DRIVE P (4/9,6/9,7/9)
0
R464
1.8k
:CHIP
R396
10k
:CHIP
-12V
G DRIVE COMP(9/9)
-12V
-3.9
Z0 5
Z1 3
-0.5
8
-5.2
1
3
4 Z
2 -3.9
R395
10k
:CHIP
IC317(2/3)
MC74HC4053FEL
SWITCH
IC324(1/3)
MC74HC4053FEL
SWITCH
C
4
-0.5
2
1
Y0
Y1
Y
-0.5
15
-3.9
10
0
9
0
G DRV CONT(3/9)
B
≠ SW(4/9,6/9,7/9)
IK/V
-5V
G2 G(7/9)
+5V
R455
220
:CHIP
+5V
+5V
C400
0.22
25V
F:CHIP
IC324(2/3)
MC74HC4053FEL
G BIAS CONTROL
3
R448
10k
:CHIP 0.4
0.4
4.0 12 Y0
13 Y1
Y 14
C398
0.1
25V
F:CHIP
B
0 11
D375
MA111
PROTECTOR
2
3
0.4
C399
0.01
F:CHIP
BIAS SAMPLING P
(4/9,6/9,7/9)
-2.9
C420
270p
CH:CHIP
0.4
-1.4
6
5
1
IC322(2/2)
TL082CPS
BIAS CLAMP
CONTROL
D374
MA111
PROTECTOR
7
15 X
X0
X1
44.0 4.0
1
0
GND VEE A
2
0 3
0
C410
0.01
F:CHIP
C381
0.01
F:CHIP
R397
15k
:RN-CP
BIAS CLAMP P
(4/9,6/9,7/9)
R449
6.8k
:RN-CP
G DRIVE IK
CONTROL
25V
F:CHIP
C412
0.01
F:CHIP
DRIVE SAMPLING P
(4/9,6/9,7/9)
-5V
G BIAS IK(9/9)
6
12 Y0
Y 14
7
-0.2 5
13 Y1
-0.2
B
-3.9
-1.1
-1.8
IC327(2/2)
0.1 11 C380
TL082CPS
0.33
1
4
C383
0.47
25V
F:CHIP
IC326(2/3)
MC74HC4053FEL
SWITCH
IC323(1/2)
TL082CPS
G BIAS CLAMP
C403
0.047
F:CHIP
8 70 10 6
C411
0.01
F:CHIP
R400
10k
:CHIP
2.2
16V
R466 F:CHIP
10k
8
2 :CHIP
16
VCC
R450
5.6k
:RN-CP
-5V
C407
0.01
F:CHIP
IC324(3/3)
MC74HC4053FEL
G BIAS CLAMP C405
R460
220
:CHIP
8
6
R459 5
-1.8 5.6k
7
IC323(2/2):RN-CP
TL082CPS
G BIAS CLAMP
R469
10k
:CHIP
IC322(1/2)
TL082CPS
BIAS CLAMP
CONTROL
R461
R456 68k
5.6k :RN-CP
:RN-CP
R401
10k
:RN-CP
6
0 5
G DRIVE IK (9/9)
7
-1.1
IC328(1/2)
NJM4558M
G DRIVE IK AMP
+5V
IC321(1/2)
TL082CPS
G DRIVE V
CONTROL
R434
10k
:RN-CP
R429
220
:CHIP
8
-0.6
3
2
IC326(1/3)
MC74HC4053FEL
SWITCH
R427
10k
:CHIP
2
1
1
4
C391
0.01
B:CHIP
Z 15
0
Z0
Z1
6
0 5
16
7
-2.5
VCC
5
3
-0.6
C
-0.6
-0.6
0.1 10
C390
0.01
F:CHIP
IC321(2/2)
TL082CPS
G DRIVE V
CONTROL
X0
X1
C386
0.047
25V
B:CHIP
R411
10k
:CHIP
-0.8
4
+5V
IC326(3/3)
MC74HC4053FEL
SWITCH
X
2
-0.8
3
-0.8
A VEE GND
6 9 7 8
0.1
-5V
BLACK SAMPLING P
(1/9,2/9,3/9,4/9,6/9,7/9)
8
-0.5
1
4
4
IC327(1/2)
TL082CPS
G DRIVE
CONTROL
C388
0.01
F:CHIP
C387
0.01
F:CHIP
WHITE SAMPLING P
(1/9,3/9,4/9,6/9,7/9)
0
G DRIVE V(5/9)
R416
15k
:RN-CP
5
R413
4.3k
:RN-CP
8
2
3
1
4
-0.8
IC328(2/2)
NJM4558M
G DRIVE V AMP
-5V
(5/9)
BK
G VIDEO OUT
G DRIVE IK/V CONTROL
B-SS3280<AEP>-BK.-P5
11-24
A
B
C
D
11-24
E
F
G
H
BK (6/9)
BK (6/9)
120V
+5V
1
+120V
IC519
TDA6101Q/N3
VIDEO AMP
R640
82k
:CHIP
1
4
-5V
6
7
S
0
124.6
74.3
VOC
76.4
VOF
73.2
5
VCN
4
VDDH
IOM
5.2
0
3
8
72.2
TP507
B
C641
4p
CH:CHIP
5.2
C595
0.01
B:CHIP
R652 R656
74.3
39k
39k
1/2W :CHIP
:RN
D569
RD22M-B3
PROTECTOR
-0.3
R646
10k
:CHIP
R661
100
1/2W
:RC
9
B
+5V
D571
HSM83-TL
PROTECTOR
21
R645
1k
:RN-CP
0
0
VIDEO TIMING P
(4/9,5/9,7/9)
B CUTOFF(9/9)
2
C599
10
160V
:HT
C597
0.01
200V
0.6
C590
0.01
F:CHIP
-5V
1
Q581
2SK520
VIDEO OUT
SWITCHING
22
4
C
9
8
-0.3 2
3
Z
Q580
2SK520
VIDEO OUT
SWITCHING
R634
10k
:CHIP
CN4
4P
BLK
:S-MICRO
B
5.2
S
R641
4.7k
:CHIP
0.6
5 Z0
3 Z1
GND
IC518(2/2)
TL082CPS
AMP
VIN
IC517(3/3)
MC74HC4053FEL
CUTOFF SW
TP506
VDDL
B
DB(3/9)
VIP
5V
1
2
3
4
D570
HSM83-TL
PROTECTOR
74.2
KB
NC
NC
GND
5
6
7
TO
C BOARD
CN506
IC529(1/2)
LM393PS
IC529(2/2)
LM393PS
COMPARATOR
-5V
R647
7.5k
:RN-CP
Q590
DTC144EKA
B CUTOFF SW
R648
390k
:RN-CP
C594
100p 71.7
CH:CHIP
R662
100k
:RN-CP
R651
5.6k
:RN-CP
R657
68k
:CHIP
Q582
2SC1654
SWITCH
R589
10k
:CHIP
R659
10k
:CHIP
BIAS & DRIVE P (4/9,5/9,7/9)
0
B DRIVE COMP(9/9)
3
4 Z
2 -3.9
R590
10k
:CHIP
R658
1.8k
:CHIP
-12V
8
-5.2
1
IC517(2/3)
MC74HC4053FEL
SWITCH
IC524(1/3)
MC74HC4053FEL
SWITCH
C
4
-3.9
Z0 5
Z1 3
-0.1
-0.1
2
1
Y0
Y1
Y
-0.1
15
-3.9
2
100
9
0
B DRV CONT(3/9)
B
≠ SW(4/9,5/9,7/9)
IK/V
-5V
-12V
G2 B (7/9)
+5V
R649
220
:CHIP
C604 C602
2.2
C600 C601 2.2
16
16V
0.01 0.01
F:CHIP F:CHIP F:CHIP F:CHIP
+5V
+5V
C593
0.22
25V
F:CHIP
IC524(2/3)
MC74HC4053FEL
B BIAS CONTROL
0.4
4.2 12 Y0
13 Y1
Y 14
B
0 11
C591
0.1
25V
F:CHIP
2
3
0.4
C592
0.01
F:CHIP
BIAS SAMPLING P
(4/9,5/9,7/9)
C620
270p
CH:CHIP
D568
MA111
PROTECTOR
R642
10k
:CHIP 0.4
-2.6
R655
R650 68k
5.6k :RN-CP
:RN-CP
0
-1.1
6
5
1
IC522(2/2)
TL082CPS
B BIAS CLAMP
CONTROL
D567
MA111
PROTECTOR
6
7
R653 5
-1.6 5.6k
IC523(2/2)
TL082CPS
B BIAS CLAMP
R594
10k
:CHIP
R660
10k
VCC
15 X
X0
X1
44.2 4.2
GND VEE A
2 :CHIP
1
2
0 3
0
IC523(1/2)
TL082CPS
B BIAS CLAMP
8
0
C603
0.01
F:CHIP
C596
0.047
F:CHIP
C605
0.01
F:CHIP
DRIVE SAMPLING P
(4/9,6/9,7/9)
C574
0.01
F:CHIP
R591
15k
:RN-CP
-5V
R644
5.6k
:RN-CP
-5V
B BIAS IK(9/9)
0
BIAS CLAMP P
(4/9,5/9,7/9)
R595
10k
:RN-CP
6
5
B DRIVE IK(9/9)
R643
6.8k
:RN-CP
3
TL082CPS
B DRIVE IK
CONTROL
F:CHIP
1
4
8 70 10 6
C576
0.47
25V
F:CHIP
6
12 Y0
Y 14
7
0.2
5
13 Y1
0.2
B
-3.9
-1.5
-0.8
C573
0.33
IC527(2/2)
0 11
25V
C598
2.2
16V
F:CHIP
16
7
IC526(2/3)
MC74HC4053FEL
SWITCH
IC524(3/3)
MC74HC4053FEL
B BIAS CLAMP
R654
220
:CHIP
8
:RN-CP
R663
10k
:CHIP
IC522(1/2)
TL082CPS
BIAS CLAMP
CONTROL
7
-0.8
IC528(1/2)
NJM4558M
B DRIVE IK AMP
+5V
+5V
IC526(3/3)
MC74HC4053FEL
SWITCH
IC521(1/2)
TL082CPS
B DRIVE V
CONTROL
-0.5
R628
10k
:RN-CP
R623
220
:CHIP
8
3
2
2
1
1
4
C584
0.01
B:CHIP
Z0
Z1
Z
15
0
C
-0.5
IC526(1/3)
MC74HC4053FEL
SWITCH
R621
10k
:CHIP
-0.5
0.1 10
C583
0.01
F:CHIP
6
0 5
C579
0.047
25V
B:CHIP
16
7
-2.4
R605
10k
:CHIP
-0.7
VCC
5
3
-0.5
IC521(2/2)
TL082CPS
B DRIVE V
CONTROL
X0
X1
X
-0.7
C581
0.01
F:CHIP
A VEE GND
2
8
1
4
-0.1
4
3
-0.6
4
IC527(1/2)
TL082CPS
B DRIVE V
CONTROL
6 9 7 8
0.1
-5V
C580
0.01
F:CHIP
-5V
BLACK SAMPLING P
(1/9,2/9,3/9,4/9,5/9,7/9)
WHITE SAMPLING P
(1/9,3/9,4/9,5/9,7/9)
0
B DRIVE V(9/9)
R610
15k
:RN-CP
R607
4.3k
:RN-CP
8
2
3
1
4
-0.6
(6/9)
BK
B VIDEO OUT
IC528(2/2)
NJM4558M
B DRIVE V AMP
B DRIVE IK/V CONTROL
B-SS3280<AEP>-BK.-P6
11-25
A
B
C
D
11-25
E
F
G
H
5
BK (7/9)
BK (7/9)
IC736(4/4)
MC74HC02AFEL
PULSE GEN R733
1
5V
R731 R732
4.7k 4.7k
:CHIP :CHIP
+5V
C728
0.01
:CHIP
C782
C783
0.01
0.01
F:CHIP F:CHIP
24
IC734(1/3)
MC74HC11FEL
PULSE GEN
8
W&D P(3/9)
IC736(1/4)
MC74HC02AFEL
PULSE GEN
IC731(2/6)
MC74HC14AFEL
INVERTER 12
13
2
3
1
4IC710(1/2)
H PULSE(9/9)
R729
3.3k
:CHIP
6
5
1
2
IC731(3/6)
MC74HC14AFEL
INVERTER
6
11
8
9
7
IC710(2/2)
LM393PS
PULSE GEN
10
WHITE SAMPLING P (1/9,3/9,4/9,5/9,6/9)
IC736(3/4) 26
MC74HC02AFEL
14 PULSE GEN
4
JR731
0
:CHIP
25
BLACK SAMPLING P
WHITE SAMPLING P
IC736(2/4)
MC74HC02AFEL
PULSE GEN
26
10
7
3
BLACK SAMPLING P (1/9,2/9,3/9,4/9,5/9,6/9)
11
3
5
4
IC711(1/2)
TC7W08FU
LM393PS
PULSE GEN
R730
2.2k
:CHIP
1
G2.BRT.CONTR CONTROL
R728
5.6k
:CHIP
C729
0.01
:CHIP
(7/9)
BK
PULSE GENERATOR
0
:CHIP
2
3
DRIVE P
27
5
6
4
WHITE INSERT P(1/9,2/9)
7
≠≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠≠
W
B INSERT P-(2/9)
W B INSERT P (1/9,3/9)
+5V
IC711(2/2)
TC7W08FU
PULSE GEN
14
2
13
AFC PULSE(9/9)
12
2
1
6
5
3
4
VIDEO TIMING P(4/9,5/9,6/9)
4
7 IC731(4/6)
MC74HC14AFEL
INVERTER
IC731(1/6)
MC74HC14AFEL
INVERTER
IC735(1/4)
MC74HC02AFEL
PULSE GEN
8
6
5
IC735(2/4)
MC74HC02AFEL
PULSE GEN
14
5V
Q0
Q3
D0
D3
5
D1
D2
6
Q1
Q2
7
Q1
Q2
8
GND CLOCK
5
6
12
13
+5V
4
DRIVE SAMPLING P (4/9,5/9,6/9)
11
2
1
13
BIAS P (3/9)
3
BIAS & DRIVE P(4/9,5/9,6/9)
IC728(2/4)
MC74HC00AFEL
PULSE GEN
12
1
2
IC734(2/3)
MC74HC11FEL
PULSE GEN
IC735(3/4)
MC74HC02AFEL
PULSE GEN
2
3
+5V
5
V BLK1(1/9,9/9)
9
V S P (9/9)
1
6
BIAS SAMPLING P(4/9,5/9,6/9)
IC735(4/4)
MC74HC02AFEL
PULSE GEN
IC731(5/6)
MC74HC14AFEL
INVERTER
3
10
IC728(1/4) 7
MC74HC00AFEL
PULSE GEN
IC730(4/4)
MC74HC02AFEL
PULSE GEN
16 15 14 13 12 11 10 9
Q3
4
10
7
VCC
Q0
3
(9/9)
DRIVE P ON/OFF
≠≠
≠
RS
2
14
9
8
1
IC730(3/4)
MC74HC02AFEL
PULSE GEN
8
9
IC732
MC74HC175FEL
PULSE GEN
11
12
8
C734
0.01
F:CHIP
IC731(6/6)
MC74HC14AFEL
INVERTER
3
2
1
R727
10k
:CHIP
IC728(3/4)
MC74HC00AFEL
PULSE GEN
IC730(2/4)
MC74HC02AFEL
PULSE GEN
5
4
IC730(1/4)
MC74HC02AFEL
PULSE GEN
10
6
7
7
8
-3.6
7
6
R700
4.7k
:CHIP
0
5
1
2
4
4
3
0.8
CLK VCC
PR
D
Q
CLR
GND
Q
IC700(1/2)
TL082CPS
COMPARATOR
IC701(3/3)
MC74HC4053FEL
SAMPLING HOLD SW
4
Z0
Z1
0
0
14 Y
*
C
Y0 12
Y1 13
-0.4
B
-0.4
0
9
0
D904
1SS119
D902
MA111
PROTECTOR
11
1
2
3
4
5
6
7
R908
1M
:CHIP
IC702
MC74HC4053FEL
SIGNAL SELECT
1
COMPARATOR
IC703(1/2)
LM393PS
S PULSE SEP
R702 R705
4.7k 4.7k
:CHIP :CHIP
+5V
C704
47
6.3V
:HT-CP
-5V
0.4 ABLMA111
CONTROL
7
-1.0
D901
MA111
PROTECTOR
R919
2.7k
:RN-CP
4
TO C BOARD
CN507
C901
0.01
F:CHIP
R921
4.7k
:RN-CP
IC901(2/2)
NJM4558M
CONTRAST BUFFER
1.0
C930
22
6.3V
:HT-CP
3
2
C904
0.01
F:CHIP
TP901
R960
1k
:CHIP
1
CONT (3/9)
1.0
IC904(2/2)
LM393PS
C928
1
10V
B:CHIP
C931
1
10V
B:CHIP
G2 R(4/9)
-5.2
R725
4.7k IC700(2/2)
:CHIP TL082CPS
8
5
6
R912
33k
:RN-CP
2
3
R922
6.8k
:RN-CP
D903
-1.0
C918
0.022
B:CHIP
8
G2 G(5/9)
5.2
G1
GND
120V
R724
22
:CHIP
IC901(1/2)
NJM4558M
ABL CONTROL
R913
8.2k
:RN-CP
TP900
ABL(9/9)
G2 B(6/9)
-5V
Q706
2SA1037K
BLK OUT
+5V
-0.4
-0.4
VIDEO COMP(9/9)
C701
0.022
B:CHIP
C700
0.022
B:CHIP
R726
4.7k
:CHIP
R721 1.0
100
:CHIP
0.1
7
GB SEL (9/9)
R SEL(9/9)
IC701(2/3)
MC74HC4053FEL
SAMPLING HOLD SW
5
3
1
2
3
14
8
16 15 14 13 12 11 10 9
4 Z
10
9
13
CN5
3P
WHT
:S-MICRO
+120V
23
CONTRAST(9/9)
8
5
6 *
100
1.7 :CHIP
D701
MA111
IC728(4/4)
MC74HC00AFEL
PULSE GEN
Y1
VCC
Y0
Y
Z1
X
Z
X1
Z0
X0
EN
A
VEE
B
GND
C
R701
4.7k
:CHIP
5.2
Q705
2SC2412K
BLK OUT
R722
1.0
8
-0.4
-0.3
-0.4
5.3
5.3
+5V
120V
5.2
TP700
H BLK(8/9,9/9)
A/C BLUE(2/9)
A/C GREEN(2/9)
A/C RED(2/9)
R723
22
:CHIP
14
IC734(3/3) 9
MC74HC11FEL
PULSE GEN 11
12
11
IC707
TC7W74FU
LATCH
+5V
BIAS CLAMP P
(4/9,5/9,6/9)
13
IC904(1/2)
LM393PS
OVER LOAD
5
COMPARATOR1.0
3
2
R930
10k
:RN-CP
8
R962
100k
:CHIP
1
0
7
OVER LOAD(9/9)
6
C900 C903
0.01 0.01
F:CHIP F:CHIP
0.4
R929
4 10k
:RN-CP
-5V
+5V
BRIGHT (9/9)
8
5
0.1
R708
10k
:CHIP
-5.2
1
R704
4.7k
:CHIP
WHITE SAMPLING P
BLACK SAMPLING P
0.1
0
8
2
31.7
4 0.4
R703
4.7k
:CHIP
7
-5.2
10k
:CHIP
-5V
-5V
C751
47
16V
:HT-CP
-2.3
R716
1k
:CHIP
C702
0.01
F:CHIP
R717
100k
:CHIP -2.3
R714
1k
:CHIP
-2.3
-2.7
-2.9
Q702
2SA1037K
G2 B CONTROL
Q701
2SA1037K
G2 G CONTROL
R713
1k
:CHIP
-2.3
-2.4
D905
R980
MA111
4.7k
:CHIP BRT CONTROL
1
0.7
4 IC705(1/2)
C705
0.01
F:CHIP
Q700
2SA1037K
G2 R CONTROL
C707
0.01
F:CHIP
S.PULSE(9/9)
R718
10k
:RN-CP 0
G2 REF(9/9)
8
2
3
-2.3
R710
6.8k
:RN-CP
R720
10k
:CHIP
NJM4558M
G2 CONTROL
-5V
AUTO C/P P SW(9/9)
≠ P SW (9/9)
W/B
R741
10k
:CHIP
C708
4.7
:BP
R715
5.6k
:CHIP
R707
10k
:CHIP
6
-1.8
5 0.4
IC703(2/2)
LM393PS
S PULSE SEP R706
0
C703
0.01
F:CHIP
-2.3
6
5
R719
3.3k
:RN-CP
R712
27k
:RN-CP
IC704(1/2)
TL082CPS
BUFFER
-0.3
5
6
IC704(2/2)
TL082CPS
C714 C706
R735 2.2
R736 -0.3
2.2 -0.3 BUFFER
220
220
16V
16V
:CHIP F:CHIP F:CHIP
:CHIP
3
2 X0
8
7
1
2
4
R709
12k
:RN-CP
IC701(1/3)
MC74HC4053FEL
BRT REF SELECT
-0.3
C712
2.2
16V
F:CHIP
1
-0.3
Y1
VCC
Y0
Y
Z1
X
0.1
Z
X1
Z0
X0
EN
A
VEE
B
GND
C
9 10 11 12 13 14 15 16
5
7
6
0.1
0
0
4
3
2
1
+5V
IC706
MC74HC4053FEL
SIGNAL SELECT
-0.3
R711
47k
:RN-CP
C713
2.2
16V
F:CHIP
16
VCC
-0.3
X
15
BRT(3/9)
X1
A VEE GND
6 10 7 8
0.4
-5V
BRT CENTER(7/9)
G2 CONTROL(9/9)
7
IC705(2/2)
NJM4558M
G2 CONTROL
B-SS3280<AEP>-BK.-P7
11-26
A
B
C
D
11-26
E
F
G
H
BK (8/9)
BK (8/9)
IC802(1/2)
NJM4558M
CLAMP DLY
CONTROL
CLAMP P DLY(9/9)
+5V
BK
(8/9)
(H/V SYNC SEPARATOR,Y/C CLAMP P GENERATOR)
R865
820
:RN-CP
R864
10k
:RN-CP
4.6
2
3
1
0.7
5 Z0
3 Z1
0.9
EXT SYNC(1/9)
Z
5 6
0.8
C813
10
16V
:HT-CP
0
R805
56k
:CHIP
R809
1k
:CHIP
C816
100p
CH:CHIP
C814
100p
CH:CHIP
Q802
2SA1037K
SYNC AGC
(9/9)
SYNC ≠≠≠
INT/EXT
≠≠
Q806
2SA1037K
SYNC AGC
1.5
4
Q811
IMT2
SYNC AGC
2.5
2.5
5 6
1.8
D802
MA111
6 5
C817
1
16V
F:CHIP
0.8
R811
820
:CHIP
-0.7
R812
3.9k
:CHIP
R840
18k
:CHIP
R834
2.2k
:RN-CP
R828
330
:CHIP
4
3.1
2
2.5
3 1
-1.2
4
0.7
C
9
R806 R808
1k
1k
:CHIP :CHIP
1.5
2
R814
4.7k
:CHIP
R839
11k
:RN-CP
2.3
2.9
3.0
4.9
12 X0
13 X1
16
R820
1.5k
:CHIP
0.7
15
14
X
6
11
5.1
12
7
5
4
Q
4.9
VSS
Cx
RD
R830 C821 C824
130k
0.1
1
:RN-CP 25V
16V
F:CHIP F:CHIP
Q815
2SC2412K
SYNC AGC
+5V
R836
1.2k
:CHIP
4.5
16
1 2
6
Q
7
VSS
RD
8
3
13
IC801(1/2)
MC74HC4538AFEL
CLAMP PULSE GEN
-5V
C826
68p
15
IC800(2/3)
VDD Cx Rx
Q
MC74HC4053FEL
SWITCH
2
5.21
Cx
11
Y 15 12
5.2
Y0
Y1
B
3
8
A VEE GND
2.1 CH:CHIP
0
R838
5.6k
:CHIP
C836
470p
CH:CHIP
RD
R844
2.7k
:CHIP
Q807
2SC2412K
SYNC AGC
-5V
R872
10k
:CHIP
C834
470p
CH:CHIP
5.1
14
4.9 5
Rx
Q 10
4
5.1
Q 9
1 2
VDD Cx Rx
Q
VCC
C832
R861
4.7k
470p
CH:CHIP :RN-CP
4.5
5.1
Y CLAMP PULSE (1/9)
31
C CLAMP PULSE (1/9)
R870
4.7k
:RN-CP
5.1
14
Rx
Q
Q
10
2
0.2
9
IC804(2/2)
MC74HC4538AFEL
13 CLAMP PULSE GEN
RD
0 10
IC804(1/2)
MC74HC4538AFEL
CLAMP PULSE GEN
60 11 7 8
R815 R817 R818 C819
15k 100k 22k
0.1
:CHIP :CHIP :CHIP F:CHIP
Q804
2SC2412K
SYNC AGC
C828
470p
CH:CHIP
16
Q813
2SA1037K
SYNC AGC
R824
470
:CHIP
0.7
R845 C827 R850
82k 0.01 100k
:RN-CP F:CHIP :RN-CP
5.6k
0.9 :CHIP
C838
0.22
25V
F:CHIP R874
10k
:CHIP
+5V
Q817
2SC2412K
SYNC AGC
3.8
2.1
C818
22
6.3V
:HT-CP
C837
0.22
25V
F:CHIP
IC801(2/2)
MC74HC4538AFEL
CLAMP PULSE GEN
5.1
0.3
-5V
R869
2.7k
:CHIP
R837
22k
:CHIP
C835
100p
CH:CHIP
VCC
5
0
Q800
2SA1037K
BUFFER
-0.8
1 3
1.4
2
R822
22k
:CHIP
R875
31
4.5
0.2
GND
4
Y/G(1/9,9/9)
TP800
4
2.8
R823
330
:CHIP
1.5
1
IC800(3/3)
MC74HC4053FEL
SYNC SELECT
C815
180p
CH:CHIP
R821
1k
:CHIP
Q826
2SC3326N
C-CL-P BUFFER
1.3
2
1
R800
100
:CHIP
Q805
IMX2
SYNC AGC
2.8
Q803
IMX2
SYNC AGC 3 1
R819
33k
:CHIP
43.9
R842
68k
:RN-CP
4.5
Q820
2SA1037K
CLAMP DLY
CONTROL
7
3
R810
680
:CHIP
R807
18k
:CHIP
R816
33k
:CHIP
6
5
-5V
IC800(1/3)
MC74HC4053FEL
SWITCH
0.8
R813
1.5k
:CHIP
0.7
-5V
-5V
+5V
R801
3.9k
:CHIP
IC802(2/2)
NJM4558M
CLAMP DLY
CONTROL
Q827
2SC3326N
Y-CL-P BUFFER
8
R876
3.3k
:CHIP
Q808
2SC2412K
SYNC AGC
5V
4.1
Q824
2SA1037K
CLAMP DLY
CONTROL
3.9
R862
100k
:RN-CP
4.1
R873
47k
:CHIP
R871
47k
:CHIP
4.6
R846
15k
:RN-CP
4.1
4.1
1
R855
820
:RN-CP
R854
10k
:RN-CP
IC805
TC7S02FU
CLAMP PULSE GEN
+5V
-5V
R833
270
:RN-CP
R825
2.2k
:CHIP
Q816
2SA1037K
SYNC AGC
R835
6.8k
:CHIP
R858
100k
:RN-CP
C830
470p
CH:CHIP
C833
470p
CH:CHIP
2.9
Q809
2SC2412K
SYNC AGC
C825
150p
CH:CHIP
HS(9/9)
R827
2.2k
:CHIP
5V
TP801 R853
CS
1k
:CHIP
D803
MA111
R832
270
:RN-CP
C822
0.1
25V
F:CHIP
R843
2.2k
:CHIP
VDD Cx Rx
Q
1.7
5
4
0.4
0.3
2.2
H BLK(7/9,9/9)
30
28
16 1 2 2.9
5.1
TP803
HS
5.2
Q812
2SC2412K
SYNC AGC
1.8
R866
2.2k
R863 :CHIP
9.1k
:RN-CP
Q
Q819
2SC2412K
SYNC AGC
0.3
VSS
RD
8
3
15
5.2
11
12
6
3.6
7
144.9
Cx
Rx
Q
Q
3.6
10
4.9
9
3
Q825
2SA1037K
H SYNC BUFFER
RD
4.9
1.7
R849
330
:CHIP
R867
100
:CHIP
13
IC803(1/2)
MC74HC4538AFEL
H SYNC SEP
IC803(2/2)
MC74HC4538AFEL
H SYNC SEP
+5V
C806 C807 C808 C810 C863 C812
0.01 0.01 0.01 0.01 0.01 0.01
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
C803
0.01
F:CHIP
+5V
C850
C852
100
47
6.3V
6.3V
:HT-CP :HT-CP
C851
1000
6.3V
:HT
C853
1000
6.3V
:HT
R826
62k
:RN-CP
C861
100p
CH:CHIP
Q810
IMT2
5 6 SYNC AGC
R841
100k
:CHIP
2.5
C802
C805 C809 C847
0.01
0.01 0.01 0.01
F:CHIP F:CHIP
F:CHIP F:CHIP
4
1.8
2
3 1
Q814
2SA1037K
SYNC AGC
Q818
2SC2412K
SYNC AGC
1.7
2.6
1.1
R852
75k
:CHIP
R848
82k
:CHIP
Q829
2SC2412K
V SYNC SEP
0.3
R856
2.2k
:RN-CP
R857
2.2k
:RN-CP
R877
2.2k
:RN-CP
-5V
1.1
R829
390k
:RN-CP
-5V
C820
0.1
25V
F:CHIP
R847
10k
:CHIP
R851
33k
:CHIP
R831
2.7k
:RN-CP
0.5
C841
1
R879
100
16V
F:CHIP :CHIP
1.2
C831
1000p
B:CHIP
Q823
2SC2412K
V SYNC BUFFER
D804
MA111
V SYNC SEP
29
TP802
VS
5.2
VS(9/9)
Q828
2SA1037K
V SYNC SEP
R868
1k
:CHIP
4.5
0.6
C829
6800p
B:CHIP
R881
2.2k
:CHIP
-1.1
R880
100k
:CHIP
0
4
R860
4.7k
:CHIP
Q822
2SC2412K
V SYNC AMP
0.3
C823
0.47
50V
:HT-CP
R859
4.7k
:CHIP
R878
2.2k
:CHIP
C840
0.015
B:CHIP
CLAMP PULSE SEL(9/9)
SYNC SEP SEL(9/9)
Q821
DTC144EKA
SYNC SEP SW
B-SS3280<AEP>-BK.-P8
5
11-27
A
B
C
D
11-27
E
F
G
H
BK (9/9)
IC1
1
+6V
C1001
100 C1002 C1003
C1000
6.3V 0.01
0.01
0.01
F:CHIP :HT-CP F:CHIP F:CHIP
LM2940CT-5.0
C1027
+5V REG
C1028
47
16V
0.01
5.3
:HT-CP F:CHIP 6.7
1
+5V
BK (9/9)
C1014
C1017
C1015 C1016 2.2
C1012 C1013 2.2
16V
0.01 0.01
0.01
0.01 16V
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
C1005 C1006 C1007 C1008 C1009 C1010
0.01 0.01 0.01 0.01 0.01 0.01
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
C1019
0.01
F:CHIP
C1037
C1029 C1030 C1031 C1032 C1033 C1034 C1035 C1036 2.2 C1038 C1039
16V 0.01 0.01
0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
F:CHIP F:CHIP F:CHIP F:CHIPF:CHIP F:CHIPF:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
C1023
C1021 C1022 2.2 C1024 C1025 C1026
0.01
0.01 0.01 0.01
0.01 16V
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
5V
+5V
3
2
-6.9
-5.3
1
-5V
C1200 C1201
0.01
100
F:CHIP 6.3V
:HT-CP
C1208 C1209 C1210 C1211
2.2 0.01 0.01
2.2
16V F:CHIP F:CHIP
16V
F:CHIP F:CHIP
C11 C12
C13
C8
TP1
47
47
47
47
C1
C3
C5
C7
C9
GND
16V
0.01 0.01 0.01 0.01 16V 0.01 16V 16V
F:CHIP F:CHIP F:CHIP F:CHIP :HT-CP F:CHIP :HT-CP:HT-CP :HT-CP
IC2
LM2990
-5V REG
+5V
EE CS
GND
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
P20/
CS08
8
3
4
5
6
7
8
AO9
AO12
AO10
AO11
VDD
VCC
D+5V
CLK
LD
AO7
AO8
DO
AO9
AO12
AO10
AO11
VDD
VCC
20 19 18 17 16 15 14 13 12 11
2
DO
DI
AO6
9 10
R907
100k
:CHIP
1
AO8
AO1
AO5
8
3
JR901
14.9
-2 -2
LD
AO2
AO4
7
5.3
2
CLK
AO7
GND
AO3
6
D900
RD6.2SB
PROTECTOR
4.8
R918
100k
:CHIP
R917
100k
:CHIP
R916
100k
:CHIP
R915
100k
:CHIP
AO6
VSS
5
R900
100
:CHIP
IC900(4/4)
MC74HC125AFEL
BUFFER
-2
DI
G 100IRE(2/9)
G SET UP(2/9)
B SET UP(2/9)
B 100IRE(2/9)
CLAMP P DLY(8/9)
4
13
AO5
≠≠≠≠≠≠
RGB
≠≠≠≠≠
SW (1/9,2/9)
BLUE
≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠
ONLY(2/9)
3
5.3
5.2
R901
100k
:CHIP
-2
AO1
2
12
CH LEVEL(3/9)
DRIVE REF(3/9)
G2 REF(7/9)
AO2
AO4
1
IC900(3/4)
MC74HC125AFEL
11
BUFFER
R 100IRE(2/9)
R SET UP(2/9)
X900
8MHz
GND
AO3
IC910
MB88346BPFV-EF
D/A CONVERTER
20 19 18 17 16 15 14 13 12 11
R904
100
:CHIP
32
VSS
9 10
0.4
4
BIAS REF(3/9)
8
0.9
IC908
MB88346BPFV-EF
D/A CONVERTER
7
EMI
5
IC902
MB89613R-438
SUB MICRO
COMPUTER
32
31
30
29
28
27
26
25
24
23
22
21
20
6
6
P21/CS09
P22/CS10
P23/CS11
P24/CS12
P25/CS13
P26/CS14
P27/CS15
VSS
X1
X0
MOD1
MOD0
RSTX
5
IC900(2/4)
MC74HC125AFEL
BUFFER
R905
100
:CHIP
SCLK1
SO1
SI1
P34
P35
Vcc
P36
P37
P40
P41
P42
P43
SLOT
ID
R-Y CLAMP OFFSET(1/9)
B-Y GAIN (2/9)
+5V
4
52
53
54
55
56
57
58
59
60
61
62
63
64
5.2 10 7 5.3
-2
R902
100k
:CHIP
-2
D+5V
R-Y PULSE LEVEL(1/9)
B-Y PULSE LEVEL(1/9)
Y CLAMP OFFSET(1/9)
PROG
≠≠≠≠≠≠≠
≠≠≠≠≠≠
SW(1/9)
9 10 11 12 13 14 15 16 17 18 19
D+5V
0
-2
Q900
DTC144EKA
RESET SW
R914
4.7k
:CHIP
-2
R BIAS IK(4/9)
8
AO9
AO12
9 10
R1004
100
:RN-CP
+5V
S.PULSE (7/9)
AO10
AO11
VDD
VCC
R1015
27k
:RN-CP
D+5V
R1016
100
:RN-CP
AO3
AO2
AO1
AO4
AO5
DI
AO6
CLK
LD
AO7
AO8
DO
AO9
AO12
AO10
AO11
VDD
VCC
R1017
27k
:RN-CP
20 19 18 17 16 15 14 13 12 11
B DRIVE V(6/9)
GND
9 10
VCC
B DRIVE IK(6/9)
VSS
8
VDD
R1014
100
:RN-CP
7
AO11
CHROMA(1/9)
R1018
100
:RN-CP
IC911
MB88346BPFV-EF
D/A CONVERTER
6
AO12
AO10
VCC
5
AO9
AO11
VDD
4
DO
AO10
3
LD
AO8
AO12
2
AO7
DO
AO9
1
CLK
LD
AO8
R1013
27k
:RN-CP
R1023
27k
:RN-CP
20 19 18 17 16 15 14 13 12 11
R1022
100
:RN-CP
(SYSTEM CONTROL,D/A CONVERTER)
AO6
9 10
BK(9/9)
DI
8
BRIGHT(7/9)
AO1
AO5
7
R1021
27k
:RN-CP
AO2
AO4
6
BRT CENTER
(7/9)
AO3
5
R1020
100
:RN-CP
4
CONTRAST
(7/9)
-2
GND
3
C907 C908 C909 C911 C915 C917 C921 C926 C924 C925
47
0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
47
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP 6.3V 6.3V
:HT-CP :HT-CP
VSS
2
C902 C905
C910 C914 C927 C929
0.01 0.01
47
0.01 0.01
47
F:CHIP F:CHIP F:CHIP F:CHIP 6.3V 6.3V
:HT-CP :HT-CP
1
R1019
27k
:RN-CP
R1010
100
:RN-CP
+5V
R1024
100
:RN-CP
IC906
MB88346BPFV-EF
D/A CONVERTER
D+5V
R CUTOFF(4/9)
CLK
AO7
R1011
27k
:RN-CP
20 19 18 17 16 15 14 13 12 11
DO
DI
AO6
9 10
7
AO8
R1009
27k
:RN-CP
8
6
LD
AO1
AO5
7
CLK
AO7
AO2
AO4
6
AO6
AO3
5
5
5
R1003
27k
:RN-CP
G DRIVE V(5/9)
GND
4
DI
G DRIVE IK(5/9)
VSS
3
4
AO5
R1008
100
:RN-CP
2
AO1
R1005
27k
:RN-CP
R1012
100
:RN-CP
IC909
MB88346BPFV-EF
D/A CONVERTER
1
AO2
AO4
R1007
27k
:RN-CP
20 19 18 17 16 15 14 13 12 11
AO3
3
R DRIVE V(4/9)
2
R DRIVE IK(4/9)
GND
6
-2
R931
100k
:CHIP
VSS
7
H PULSE (7/9)
V BLK1 (1/9,7/9)
H BLK (7/9,8/9)
CS VDD
SO HOLD
WP SCK
GND SI
8
R920
100k
:CHIP
JR903
R1002
100
:RN-CP
1
IC903
X25040-C7000
D+5V
EEP ROM
G BIAS IK(5/9)
R1006
100
:RN-CP
IC907
MB88346BPFV-EF
D/A CONVERTER
G CUTOFF(5/9)
R1001
27k
:RN-CP
B BIAS IK
(6/9)
R923 R925 R927
4.7k 4.7k 4.7k
:CHIP :CHIP :CHIP
R928
R924
R926
4.7k
4.7k
4.7k
:CHIP
:CHIP :CHIP
AFC PULSE(7/9)
HS (8/9)
VS (8/9)
4
5
IC900(1/4)
MC74HC125AFEL
BUFFER
14
9
FL902
D+5V
51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
D+5V
R906
100
:CHIP
C1242 C1243 C1244 C1245 C1246
0.01 0.01 0.01 0.01
0.01
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
5V
R958 R959
10k 10k
:CHIP:CHIP
3
37
R903
100k
:CHIP
C1235 C1236 C1237 C1238 C1240
0.01 0.01 2.2
2.2
2.2
16V
16V F:CHIP F:CHIP 16V
F:CHIP
F:CHIP F:CHIP
R909 R910 R911
100k 100k 100k
:CHIP:CHIP:CHIP
2
36
R948
10k
:CHIP
1
35
5V-2
R955 R956
10k
10k
:CHIP :CHIP
3
34
VIDEO COMP(7/9)
R SEL(7/9)
GB SEL(7/9)
R953
10k
:CHIP
2
4
R949 R950 R951 R952
10k
10k
10k
10k
:CHIP :CHIP :CHIP :CHIP
R947
10k
:CHIP
1
33
+120V
SCLK2
SO2
SI2
P50/CS16
P51/CS17
P52/CS18
P53/CS19
P54/CS20
P55/CS21
P56/CS22
P57/CS23
Vcc
N.C.
GND
INT0
P61/INT1
P62/INT2
P63/INT3
P64
GND
3
R20
39
1/4W
:FPRD
1a
1b
+120V
+120V
2a
+120V
2b
GND
3a
-15V
GND
3b
-15V
4a
-15V
4b
+15V
5a
+15V
5b
-6V
6a
-6V
-6V
6b
+6V
7a
+6V
+6V
7b
DU G
8a
DU B
8b
R10
100
DU R
9a
:CHIP
V S P
9b
V S P(7/9)
ABL
ABL(7/9)
10a
G2 CONTROL
10b
G2 CONTROL(7/9)
GND
11a
Y/G
11b
Y/G(1/9,8/9)
GND
12a
2Y/2G
2Y/2G(1/9)
12b
GND
13a
PB/B
13b
PB/B (1/9)
GND
14a
2PB/2B
14b
2PB/2B (1/9)
GND
15a
PR/R
15b
PR/R(1/9)
GND
16a
2PR/2R
16b
2PR/2R (1/9)
GND
17a
CHAR BLK
CHAR BLK
17b
(2/9)
CHAR G
CHAR G (3/9)
18a
CHAR B
18b
CHAR B (3/9)
CHAR R
CHAR R (3/9)
19a
AFC PULSE
19b
R11 100 :CHIP
HS
20a
VS
20b
2HS
21a
D12
D11
RD6.2SB RD6.2SB
2VS
21b
PROTECTOR PROTECTOR
NC
22a
NC
22b
D13
NC
23a
RD6.2SB
PROTECTOR
NC
23b
R14 100 :CHIP
H PULSE
24a
R12 100 :CHIP
V BLK1
24b
R13 100 :CHIP
H BLK
25a
D14
V BLK2
25b
RD6.2SB
PROTECTOR
+5V SENSE
26a
RESET
26b
S.PULSE
27a
MISO
27b
MOSI
28a
FL901
SCLK
28b
DIGITAL +5V
29a
EMI
DIGITAL +5V
29b
FL900
DIGITAL GND
30a
EMI
-2
DIGITAL GND
30b
CH SLOT3
31a
INTERNAL SIG. 31b
GND
32a
GND
32b
TO
TB BOARD
CN3
GND
-12V
120V
CN1
64P
B TO B
2
AUTO C/P P SW (7/9)
-12.1
≠ P SW (7/9)
W/B
-12V
3
IC3
NJM7912FA
-12V REG
C1229 C1230 C1231
0.01 0.01
0.01
F:CHIP F:CHIP F:CHIP
C1227
2.2
16V
F:CHIP
-5V
1
2
-17.6
C1222 C1223 C1224 C1225
0.01
0.01
2.2
2.2
16V F:CHIP F:CHIP
16V
F:CHIP F:CHIP
C1215 C1216 C1217 C1218
0.01 0.01 0.01 2.2
F:CHIP F:CHIP F:CHIP 16V
F:CHIP
C1213
2.2
16V
F:CHIP
-5V
R-Y GAIN(2/9)
B-Y CLAMP OFFSET(1/9)
C1247 C1248
0.01
47
16V F:CHIP
:HT-CP
C14
33
C15
25V
0.01
:HT-CP F:CHIP
R DRIVE COMP (4/9)
G DRIVE COMP (5/9)
B DRIVE COMP (6/9)
≠ SW(4/9,5/9,6/9)
IK/V
CONT
≠≠≠≠≠≠
≠≠≠≠≠0 (1/9)
MONO (1/9)
≠≠≠≠≠≠≠≠
BK
≠≠≠≠≠≠≠≠≠
SELECT(1/9)
CH BACK H/B (2/9)
-6V
3
OVER LOAD (7/9)
SYNC SEP SEL (8/9)
CLAMP PULSE SEL(8/9)
SYNC INT/EXT
≠≠≠
≠≠
(8/9)
DRIVE P ON/OFF
≠≠
≠
(7/9)
2
B CUTOFF (6/9)
D+5V
B-SS3280<AEP>-BK.-P9
11-28
A
B
C
D
11-28
E
F
G
H
BK
BK
BK Board IC Block Diagrams
15
14
13
12
3Q
16
CLOCK
5
3Q
#£
6
4D
#™
MC74HC175FEL (IC732)
CONT 2 OUT 2
3D
#¡
3
IN 2
7
8
4Q
2
Vcc
4Q
1
CXA1211M (IC305)
VCC
BK Board Waveforms (2/2)
BK Board Waveforms (1/2)
11
10
9
Q
Q
CLR
VCA 2
Q
CLR
VCA 1
3
4
CONT 1 OUT 1
GND
1
IN 1
1.8Vp-p (H)
7
990mVp-p (H)
8
4.2Vp-p (V)
2.8Vp-p (H)
4.1Vp-p (H)
5.1Vp-p (V)
!º
2.0Vp-p (H)
!¡
2.8Vp-p (H)
5Vp-p (H)
GAIN-CONT
DC-CONT
MB88346BPFV (IC906-911)
!™
D0
2.7Vp-p (H)
!¢
2.8Vp-p (H)
D1 D2
D3 D4
D5 D6
D7 D8
20
GND
19
A02
18
A01
17
DI
16
CLK
15
LD
A08 7
14
DO
A09 8
13
A12
ADDRESS
DECODER
A03 2
8
!∞
12
D0
A05 4
A06
!§
3Vp-p (H)
!¶
3.1Vp-p (H)
!ª
2.2Vp-p (H)
@º
1
1 2 3 4
12
A07
76Vp-p (H)
@¡
D7
D0
D7
8 BIT
LATCH
8 BIT
LATCH
8 BIT
R-2R
D/A CONVERTER
8 BIT
R-2R
D/A CONVERTER
5
3Vp-p (H)
!•
4
5
6
7
8
6
X4 I/O
1
16 VDD
X6 I/O
2
15 X2 I/O
XC I/O
3
14 X1 I/O
X7 I/O
4
13 X0 I/O
X5 I/O
5
12 X3 I/O
EN IN
6
11 A IN
VEE
7
10 B IN
GND
8
D9 D10 D11
A04 3
3.1Vp-p (H)
3
5 OUT
VSS 1
3.2Vp-p (H)
Q
2
MC74HC4051F (IC116, 316, 516)
6 GND
12 BIT SHIFT REGISTER
!£
CK
CLR
Q
7 DC CONT
GCA
GAIN
3
CONT
V EE 4
3.1Vp-p (H)
D
8 Vcc
REGULATOR
GND 2
#¶
9
CLEAR
CXA1521M (IC112, 303, 312, 503, 512)
D
Q
2Q
CK
CLR
Q
#§
2Q
#∞
IN 1
2D
#¢
4.2Vp-p (H)
1D
6
5.7Vp-p (8MHz)
1Q
5
4.6Vp-p (H)
2.3Vp-p (H)
1Q
4
2.3Vp-p (H)
D CK
GND
2
1
2.2Vp-p (H)
Q
CK D
A10 9
12
A11
VDD 10
11
VCC
A12
A01
9
C IN
MC74HC4053F (IC101, 104, 110, 113, 117,
124, 126, 301, 304, 310, 313,
317, 324, 326, 500, 501, 504,
510, 513, 517, 524, 526, 701,
702, 706, 800)
X1
1
X0
2
16 VDD
Y1
3
14 ZC
YC
4
13 Z1
Y0
5
EN
6
11 AZ
VEE
7
10 AX
GND
8
OPEN
15 XC
12 Z0
OPEN
MB89613R-236/438 (IC902)
@¢
X0 23
X1 24
A08 41
128µsec
63.5µsec
5Vp-p
@ª
4.2Vp-p (H)
59 PTO
8 BIT PULSE
WIDTH COUNT
TIMER
58 WTO
56 PWC
@¶
AD7 42
@•
8 BIT
PWM TIMER
RESET
(WDT)
RST 20
AD0 49
5Vp-p (H)
CLOCK CONTROL
CMOS I/O PORT
5Vp-p
MOD0 21
MOD1 22
ALE 26
RD 27
WR 28
CLK 29
RDY 30
HRQ 31
HAK 32
BUFC 33
4.3Vp-p (H)
EXTERNAL
BUS
INTERFACE
54 SI1
53 SO1
52 SCK1
51 ADST
3 SI2
2 SO2
1 SCK2
BUZZER OUT
64
60
61
62
63
BZ
P40
P41
P42
P43
N-CH OPEN DRAIN I/O PORT
4 P50
RAM
(256 X 8bit)
CPU
N-CH OPEN DRAIN I/O PORT
EXTERNAL
INTERRUPT
INPUT PORT
ROM
(8K X 8bit)
11-29
11-29
NJM1496M (IC115, 315, 515)
SIGNAL
IN (+)
1
14 V
GAIN ADJ
2
13 NC
GAIN ADJ
3
12 OUTPUT (–)
SIGNAL
IN (–)
4
11 NC
BIAS
5
10 CAR–
OUTPUT (+)
6
9
NC
NC
7
8
CAR+
CMOS I/O PORT
8 BIT
SERIAL 2
CMOS OUT PORT
AY
55 EC
8 BIT
SERIAL 1
A15 34
#º
4.2Vp-p (V)
16 BIT
TIMER COUNT
8
PORT 4
@§
5.2Vp-p (H)
TIME BASE
TIMER
PORT 0/1
@∞
4.7Vp-p (H)
OSC
(MAX 10MHz)
PORT 2
69Vp-p (H)
9
OPEN
PORT 3
@£
1.9Vp-p (H)
PORT 6
@™
75Vp-p (H)
INTERNAL BUS
2.3Vp-p (H)
11 P57
15
16
17
18
INTO
INT1
INT2
INT3
19 P64
BK
TC4W53FU (IC107, 307, 325, 507, 508, 525)
1
COMMON
2
INH
8
VDD
7
CH0
6
CH1
5
A
OUT IN
C
LOGIC LEVEL
CONVERTOR
3
VEE
OUT IN
C
4
VSS
5
Q
C
D
Q
1
2
3
4
Q
GND
Q
6
R
D
8
CLR
7
S
CK
PR
VCC
TC7W74FU (IC707)
TDA6101Q/N3 (IC119, 319, 519)
CURRENT
SOURCE
MIRROR
MIRROR
V bias
DIFFERENIAL
STAGE
+
–
FOLLOWER
MIRROR
MIRROR
1
2
3
4
5
6
7
8
VIP
VDDL
VIN
GND
IOM
VDDH
VCN
VOC
9
VOF
X25040SI (IC903)
CS 1
STATUS
REGISTER
WRITE
PROTECT
LOGIC
X DECODE
LOGIC
512 BYTE
ARRAY
8
VDD
7
HOLD
6
SCK
5
SI
32
SO 2
WP 3
32X32
COMMNAD
DECODE
AND
CONTROL
LOGIC
WRITE
CONTROL
AND
TIMING
LOGIC
32
32X32
64
64X32
GND 4
4
8
Y DECODE
DATA REGISTER
11-30
BC (1/4)
BC (1/4)
(2/4,3/4)
A7
A6
A5
A4
A3
A2
A1
A0
A4
A3
A2
A1
A0
R91
R93
R95
R97
100k 100k 100k 100k
:CHIP :CHIP :CHIP :CHIP
(3/4)R90
R92
R94
R96
A0 100k 100k
100k 100k
(2/4):CHIP
:CHIP :CHIP :CHIP
5V-2
4
8
5V-2
74.0
5
6
4
7
8
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
P61
A60
A15
A14
A13
A12
A11
A10
A9
A8
VSS
VSS
A7
A6
A5
A4
A3
A2
A1
A0
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
5V-2
A0
A1
A2
CS2
CS3
CS1
Y7
GND
VCC
Y0
Y1
Y2
Y3
Y4
Y5
Y6
CS0 (2/4)
CS1 (2/4)
CS2 (2/4)
CS (3/4)
(3/4)
(4/4)
(4/4)
STBY
(4/4)
POWER
OVERLOAD (4/4)
D07
D06
D05
D04
D03
RD
WR
D07
D06
D05
D04
D03
JR15
0
:CHIP
D+5V
R35 R34
100k 100k
:CHIP :CHIP
3
5V-2
A1
A0
*
0.9A2
RD
WR
R32 R33
100k 100k
:CHIP:CHIP
5V-2
VP1
VP0
A2
A1
A0
1.7
3
N.C.
PE1
PE0
A2
A1
A0
CS
RD
WR
Vss
ODEN
CLR
D7
D6
D5
D4
D3
N.C.
N.C.
4.7
5.1
VCBLK
0 VB
0 VG
0 VR
0
52 PE2
53 PE3
54 PA0
55 PA1
56 PA2
5V-2 57 Vss
58 Vdd
V3
59 PA3
H0
60 PA4
H1
61 PA5
525/625 62 PA6
D/A 63 PA7
HP0 64
PB0
D2
D1
D0
PD7
PD6
PD5
Vdd
Vss
PD4
PD3
PD2
PD1
PD0
IC5
CXD1095Q
PARALLEL I/O
2
3
4
5
6
7
8
32
31
30
29
28
27
26
25
24
23
22
21
20
D02
D01
D00
BAUD02
BAUD01
BAUD00
5V-2
BAUD12
BAUD11
BAUD10
BAUD21
BAUD20
BAUD SEL
(2/4)
9 10 11 12 13 14 15 16 17 18 19
HP1
HP2
HP3
HP4
HP5
HP6
HP7
5V-2
C5
47
16V
:HT-CP
R11
10k
:CHIP
Q1
5.2 DTC144EK-T146
CHARA GEN RESET
0
RESET
(4/4)
0
R16
10k
:CHIP
2
3
4
5
6
7
8
32
31
30
29
28
27
26
25
24
23
22
21
20
D02
D01
D00
5V-2
R62
1.5k
:CHIP
R61
820
:CHIP
R60
680
:CHIP
SELECT SYNC SEP
(3/4)
SEL SYNC
(3/4)
SAD BLK DISP
(3/4)
SAD DISP
(3/4)
4
9 10 11 12 13 14 15 16 17 18 19
SDI CC
(3/4)
CC ON/OFF
(3/4)
CC C/T
(3/4)
CC L1/L2
(3/4)
INT SG EN
(3/4)
SYNC ON/OFF
(3/4)
EXT.INT.SG.EN
(3/4)
SLAVE_TX
(2/4)
MASTER_TX
(2/4)
B-SS3280<AEP>-BC.-P1
PARA RMT (2/4)
H POSI
(3/4)
DAC_ENABLE(3/4)
(3/4)
525/625
H SEL
(3/4)
V SEL
(3/4)
(3/4)
V_POS
D+5V
5.2
SLOT1
0 1
REM8
REM7
REM6
REM5
REM4
REM3
REM2
REM1
5.2
CHARA (4/4)
D2
D1
D0
PD7
PD6
PD5
Vdd
Vss
PD4
PD3
PD2
PD1
PD0
IC6
CXD1095Q
PARALLEL I/O
1
C3
C4
22p
22p
CH:CHIP CH:CHIP
5.1
52 PE2
53 PE3
54 PA0
55 PA1
56 PA2
57 Vss
58 Vdd
59 PA3
60 PA4
61 PA5
62 PA6
63 PA7
64 PB0
N.C.
N.C.
PB1
PB2
PB3
PB4
PB5
PB6
PB7
Vss
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
N.C.
VP2
VP3
V0
V1
V2
R9
100k
:CHIP
SLOT0
SLOT3
SLOT2
SLOT5
SLOT4
SLOT7
SLOT6
9 10
BUSY
HSYNC
CLK
VSYNC
BBLNK
CS
DATA
GBLK
PCL
RBLK
VDD
VCBL
VB
CKOUT
VG
OSCOUT
OSCIN
VR
GND
VMON
51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
N.C.
PE1
PE0
A2
A1
A0
CS
RD
WR
Vss
ODEN
CLR
D7
D6
D5
D4
D3
N.C.
N.C.
51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
N.C.
N.C.
PB1
PB2
PB3
PB4
PB5
PB6
PB7
Vss
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
N.C.
1.8
2
75
76 P91/FTOA3
77 P92/TXD2
78 P93/RXD2
79 P94/SCK2
80 P95/TXD1
81 P96/RXD1
82 P97/SCK1
83 VSS
84 EXTAL
1 XTAL
2 VSS
3 P10/PHAI
4 P11/E
5 P12/BACK
6 P13/BREQ
7 P14/WAIT
8 P15/IRQ0
9 P16/IRQ1
10 P17/TMO
11 AS
C392
C271
0.01
47
F:CHIP 16V
:HT-CP
Q5
DTC144EK-T146
+12V SW
2
16 15 14 13 12 11 10 9
1
74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54
9 10 11 12 13 14
28 27 26 25 24 23 22 21 20 19 18 17 16 15
8
+5V
5.2
0
1
Q2
DTA144EK-T146
SLAVE CPU RESET
7
8
2.4
2
Q4
DTC144EK-T146
+5V SW
SENSE
TALLY
C9
0.01
F:CHIP
4
3
6
8
7
5.1
5.2
0 1
2
4.0
5
6
5
6
5
4.3
A5
A6
A7
IC9(1/2)
TC7W32FU(TE12R)
SRAM ENABLE
SIO RESET (2/4)
R17
10k
:CHIP
7
4
8
L1
6.8µH2.5
10
IC12(2/4) 5.2
TC74VHC125F(EL)
INT BUS DRIVER
SCLK (4/4)
2 4.7
7
6
MOSI (4/4)
3
IC12(1/4) 0.8
TC74VHC125F(EL)
INT BUS DRIVER
2
14
GND
VCC
RESET N.C.
CS
V OUT
BAT
CS
20 19 18 17 16 15 14 13 12 11
1
MISO(4/4)
5.1
5.2
5.1
5.2
12
4.9
1
IC12(3/4) 0.5
TC74VHC125F(EL)
INT BUS DRIVER 9
0
D07
D06
D05
D04
D03
CC RESET (3/4)
IC7
µPD6453GT-101-E1
CHARACTER GEN
R27
1k
:CHIP
IC8(6/6)
SN74HC05ANS-E05
INVERTER
AFC P(3/4,4/4)
VCC
Y0
Y1
Y2
Y3
Y4
Y5
Y6
8
5V-2
IC8(1/6)
SN74HC05ANS-E05
INVERTER
Q6
2SA1221-T-KLM
+5V DRIVER
5.2
0
1
D+5V
13
0.3
A0
A1
A2
CS2
CS3
CS1
Y7
GND
BATS1
LITHIUM BATTERY
V BLANK2
(4/4)
V BLANK1(4/4)
5.2
12
C1
C2
22p
10p
CH:CHIP CH:CHIP
R28
1k
:CHIP
4
13
3
C246
100
C375
0.01 6.3V 5.2
F:CHIP :HT-CP 3.4
2
2.6
R21
15k
:CHIP 12.6
0
5.2
IC2
MM1026BFB
RESET
2
1
5.2
R19
6.8k
:CHIP
A10
R20
4.7k
:CHIP 12.6
4.6
0
1
X1
7
C7
0.01
F:CHIP
20.0MHz
IC15(6/6)
TC74VHCU04F(EL)
INVERTER
RXD2 (4/4)
Q3
Q10
DTA144EK-T146
SIO RESET
DTC144EK-T146
CC RESET
6
R6
10k
:CHIP
VITC_DTSE
(3/4)
SIO CLK
(3/4)
TXD2 (4/4)
R18
2.2k
:CHIP
RD
IC13
TC74VHC138F(EL)
ADDRESS SELECTOR
16 15 14 13 12 11 10 9
5
R10
1M
:CHIP
+12V DRIVER
D+5V
4
3.3
M/S SELECT(2/4)
IC125(6/6)
SN74HC05ANS
INVERTER
IC10
TC74VHC138F(EL) 5V-2
ADDRESS SELECTOR
3
A15
A16
A17
A18
D+5V
R7
100k
:CHIP
11
D07
D06
D05
D04
D03
Q7
12V 2SA1221-T-KLM
12
2
10
R8
100k
:CHIP
D00
D01
D02
5
WR
RD
13
R29 10k :CHIP
IRQ0
(2/4)
IRQ1
(2/4)
A10
5V-2
WR
A13
A8
A9
A11
MICROCOMPUTER
PROGRAM,S-RAM
ADDRESS SELECTOR
PARALLEL I/O
CHRACTER GEN
+5V
A18
R1
10k
:CHIP
1
5V-2
IC15(4/6)
TC74VHCU04F(EL)
INVERTER
IC15(5/6)
9 TC74VHCU04F(EL)
INVERTER
RD
VCC
WR
A13
A8
A9
A11
OE
A10
CE
D7
D6
D5
D4
D3
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
GND
C281
C382
100
6.3V 0.01
:HT-CP F:CHIP
1
R70
1k
:CHIP
P90
/FTOA2
8
A17
A14
A13
A8
A9
A11
4
R2
10k
:CHIP
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
WR
3
R4
10k
:CHIP
R3
10k
:CHIP
5V-2
2
D00
D01
D02
R5
10k
:CHIP
IC4
CXK58257CM -70LL-T6 SRAM
1
D+5V
9 10 11 12 13 14 15 16
10
5V-2
8
VSS
N.C.
NMI
RES
STBY
MD2
MD1
MD0
VCC
WR
RD
DS
R/W
7
IC1
HD6475368CP-10
-EG2.0
MICROCOMPUTER
6
CHARA-2
(4/4)
CHARA-1
(4/4)
5
5.1
≠≠≠≠≠
≠≠≠≠≠≠
V
SYNC
(3/4,4/4)
CHARA-3
(4/4)
D07
D06
D05
D04
D03
D02
D01
D00
4
4.9
≠≠≠≠≠
≠≠≠≠≠≠
H
SYNC
(3/4,4/4)
D07
D06
D05
D04
D03
D02
D01
D00
P63/IRQ5/A19
VCC
P70/TMCI
P71/FTI1
P72/FTI2
P73/FTI3/TMRI
P74/FTOB1/FTCI1
P75/FTOB2/FTCI2
P76/FTOB3/FTCI3
P77/FTOA1
VSS
AVSS
P80/AN0
P81/AN1
P82/AN2
P83/AN3
P84/AN4
P85/AN5
P86/AN6
P87/AN7
AVCC
3
5V-2
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
VCC
WE
N.C.
A14
A13
A8
A9
A11
OE
A10
CE
D7
D6
D5
D4
D3
VPP
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
GND
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
5.2
2
IRQ2
(2/4)
+5V
IC3
CAT28F020P-15
PROGRAM
1
P62/IRQ4
/A18
BC(1/4)
D00-D07 (2/4,3/4)
A0-A4
5.2
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
RD/WR
C8
0.01
F:CHIP
5
SLOT (4/4)
SLOT (4/4)
IC15(2/6)
TC74VHCU04F(EL)
INVERTER
IC15(3/6)
TC74VHCU04F(EL)
INVERTER
IC125(4/6)
SN74HC05ANS
INVERTER
D+5V
14
IC15(1/6)
TC74VHCU04F(EL)
INVERTER
1
2 3
4 5
6
3
5V-2
R303
10k
4:CHIP
IC12(4/4)
TC74VHC125F(EL)
INT BUS DRIVER
14
12
7
11
IC9(2/2)
TC7W32FU(TE12R)
SRAM ENABLE
5
6
3
13 7
11-31
A
B
C
D
11-31
E
F
G
H
BC (2/4)
BC (2/4)
D00-D07
(1/4,3/4)
RD/WR
(1/4,3/4)
A0(1/4)
1
5V-2 14 IC121(1/6)
TC74VHCU04F(EL)
5.2 2
1 INVERTER
0
5
7
0
IRQ0(1/4)
IRQ1(1/4)
IRQ2(1/4)
5.2 6
3
IC121(2/6)
IC121(3/6)
0 TC74VHCU04F(EL)
TC74VHCU04F(EL)
5.2 4
INVERTER
INVERTER
CS2(1/4)
CS0(1/4)
CS1(1/4)
IC24
µPD71051GU-10-E2
RS-232C CONTROL
A1
A2
0
D6
DSR
D7
RESET
TXCLK
RTS
CLK
WR
TXDATA
CS
TXEMP
C/D
RD
28 27 26 25 24 23 22 21 20 19 18 17 16 15
OE
GND
BAUD20
BAUD21
D5
9 10 11 12 13 14
CTS
SYNC/BRK
RXRDY
TXRDY
D01
D00
0
3
4
5
6
7
C43
0.1
F:CHIP
8
SIO RESET(1/4)
SIO CLK(1/4)
2
C42
0.1
F:CHIP
16 15 14 13 12 11 10 9
7.8
8.9
2.9
3.8
-4.5
-8.0
-7.2
0
C41
0.1
F:CHIP
5V-2
D+5V
2.6
D1
RD6.2SB
PROTECTOR
0
0
2.4
5.2
C44
0.1
F:CHIP
IC36
MAX202CSE-TE2
RS232C INTERFACE
1
TXRDY
0
5.2
A0
RD
DTR
8
RXRDY
Y
5.2
2.5
D4
RXCLK
7
CTS
SYNC/BRK
D7
WR
GND
VDD
6
RD
Y
D4
D5
D6
D7
RXDATA
5
C/D
16 15 14 13 12 11 10 9
TXEMP
D6
8
TXDATA
CS
D0
7
WR
D5
6
CLK
D4
D1
5
TXCLK
D2
4
RESET
VCC
3
DSR
D7
2.6
D3
2
D6
5V-2
2.6
0
0
*
0
2.4
5.2
1
0
RTS
D3
D2
D1
D0
D01
D00
28 27 26 25 24 23 22 21 20 19 18 17 16 15
RD
D5
DTR
9 10 11 12 13 14
5.2
2.5
D4
RXCLK
8
WR
GND
D0
VDD
7
A2
RXDATA
6
GND
BAUD00
BAUD01
BAUD02
D3
5
TXRDY
OE
D04
D05
D06
D07
2.6
D1
4
RXRDY
0
2.4
5.2
5.2
A0
5.2
A1
5.2
D4
D5
D6
D7
D2
3
CTS
SYNC/BRK
Y
2.6
D02
D03
5.2
2
RD
D7
5V-2
1
C/D
Y
16 15 14 13 12 11 10 9
TXEMP
D6
8
TXDATA
CS
D0
7
WR
D5
6
CLK
D4
D1
5
TXCLK
RESET
D2
4
DSR
D7
VCC
3
RTS
9 10 11 12 13 14
8
A2
DTR
8
7
OE
GND
BAUD10
BAUD11
BAUD12
RXCLK
1.6
1.9
D5
1.2
D6
2.1
7
0
5.2
A1
5.2
A0
D4
VDD
D3
2
6
Y
2.6
D04
D05
D06
D07
2.6
WR 4.8
5.2
2.5
RD 1.5
0
D0
2.3
1
D7
D1
D3
D2
D1
D0
D01
D00
5V-2
2.6
28 27 26 25 24 23 22 21 20 19 18 17 16 15
5
Y
GND
6
D6
RXDATA
5
4
D0
D4
D5
D6
D7
2.3
D3
2.0
4
3
D5
D2
3
D4
D1
D02
D03
5.2
2
D2
5V-2
2.5
1
VCC
16 15 14 13 12 11 10 9
D3
2
2
1
D3
D2
D1
D0
IC21
TC74HC151AF(EL)
8 TO 1 SELECTER
D0
4
5V-2
IC23
µPD71051GU-10-E2
ISR CONTROL
D1
D3
3
IC20
TC74HC151AF(EL)
8 TO 1 SELECTER
IC22
µPD71051GU-10-E2
REMOTE1 CONTROL
D2
2
IC19
TC74HC151AF(EL)
8 TO 1 SELECTER
D04
D05
D06
D07
2.6
1
D02
D03
5.2
C45
0.1
F:CHIP
7.2
0
TP6
5.2
5.2
TP5
3
BAUD SEL(1/4)
D4
D5
RD6.2SB RD6.2SB
PROTECTOR PROTECTOR
C39
0.1
F:CHIP
OPTION_RTS
OPTION_TXD
OPTION_RXD
PARA RMT
5V-2
REM7
REM3
REM8
REM4
R46
100k
:CHIP
R42
100k
:CHIP
R47
100k
:CHIP
R43
100k
:CHIP
R48
100k
:CHIP
R44
100k
:CHIP
R45
100k
:CHIP
C551
0.01
F:CHIP
C556
0.01
F:CHIP
C552
0.01
F:CHIP
C557
0.01
F:CHIP
C553
0.01
F:CHIP
C558
0.01
F:CHIP
C554
0.01
F:CHIP
C555
0.01
F:CHIP
8
1
7
C47
15p
CH:CHIP
5
5
6
IC31(3/6)
4
5
9
8
11
5
6
IN
FL557
FL553
EMI
FL558
EMI
FL554
EMI
FL555
FL564
Y1
A3
Y2
A4
Y3
A5
Y4
A6
Y5
A7
Y6
A8
Y7
GND
Y8
11 12 13 14 15 16 17 18 19 20
FL552
EMI
1
FL563
EMI
2
FL568
FL556
EMI
3
EMI
OE2
A2
4
EMI
VCC
A1
5
FL567
5.2
5.2
5.2
5.2
5.2
5.2
5.2
5.2
REM1
REM2
REM3
REM4
REM5
REM6
REM7
REM8
D41
RD6.2SB
PROTECTOR
D550
D552
D554
RD12SB
RD12SB
RD12SB
PROTECTOR PROTECTOR PROTECTOR
R89
220
:CHIP
R87
220
:CHIP
R84
D551
D553
D555
220
RD12SB
RD12SB
RD12SB :CHIP
PROTECTOR PROTECTOR PROTECTOR
R86
220
:CHIP
D560
RD12SB
PROTECTOR
D558
R85
RD12SB
220 D556
:CHIP RD12SB PROTECTOR
PROTECTOR
D559
RD12SB
D557
RD12SB PROTECTOR
PROTECTOR
5
6
BC(2/4)
D561
RD12SB
PROTECTOR
R88
220
:CHIP
1
CN6 ISR
9P
9
INTERACTIVE
STATUS
REPORTING
OUT
REMOTE-1
6
D40
D39
D38
D37
D36
D35
D34
RD6.2SB RD6.2SB RD6.2SB RD6.2SB RD6.2SB RD6.2SB RD6.2SB
PROTECTOR PROTECTOR PROTECTOR PROTECTOR PROTECTOR PROTECTOR PROTECTOR
SERIAL CONTROL
485/RS232C INTERFACE
5
6
9
B-SS3280<AEP>-BC.-P2
CN5 REMOTE-2
9P
R551 R552 R553 R554 R555
1k
1k
1k
1k
1k
:CHIP :CHIP :CHIP :CHIP :CHIP
R556 R557 R558
1k
1k
1k
:CHIP :CHIP :CHIP
10
IC31(4/6)
IC31(5/6)
TC74VHCU04F(EL)
INVERTER
TC74VHCU04F(EL)
INVERTER
B
FL562
1
9
11-32
A
FL566
CN4
9P
TC74VHCU04F(EL) TC74VHCU04F(EL)
INVERTER
INVERTER
3
D32
D30
R77
RD6.2SB RD6.2SB
10k
PROTECTOR PROTECTOR :CHIP
D29
D33
D31
RD6.2SB RD6.2SB RD6.2SB
PROTECTOR PROTECTOR PROTECTOR
1
9
CN3
9P
IC31(2/6)
R75
10k
:CHIP
GND
3.3
12
GND
1.8
13
2
1
C46
18p
CH:CHIP
EMI
REM5
7
3.3
IC31(6/6)
TC74VHCU04F(EL)
INVERTER
EMI
GND
R74
10k
:CHIP
X2
4.9152MHz
2
EMI
REM1
REM6
REM2
REM7
REM3
REM8
REM4
6
R76
10k
:CHIP
R31
1M
:CHIP
IC31(1/6)
TC74VHCU04F(EL) 5V-2
INVERTER
2.9 14
EMI
OE1
5V-2
SG
5
Q1
EMI
DCD
DSR
RXD
RTS
TXD
CTS
DTR
4
CLOCK
EMI
FL551
RXD
3
GND
5V-2
RXD
2
Q2
2.6
D1
D0
2.6
TXD
VCC
2.6
Q6
Q11
2.6
Q5
Q10
2.6
Q7
Q8
2.6
Q4
Q9
2.6
Q3 RESET
2.6
TXD
Q12
16 15 14 13 12 11 10 9
1
D3
D4
D2
D5
D6
D7
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
6
5V-2
4
REM1
REM2
REM3
REM4
REM5
REM6
REM7
REM8
7
FL8
IC30
TC74VHC4040F(EL)
CLOCK DIVIDER
8
IC29
TC74VHC541F(EL)
REMOTE2 DRIVER
0
5.2
10 9
8
R41
100k
:CHIP
(4/4)
(4/4)
(4/4)
(1/4)
REM5
D+5V
C314
0.01
F:CHIP
REM2
16 15 14 13 12 11 10 9
7
8
-5.4
-9.5
9.4
0
6
7
C35
0.1
F:CHIP
5
6
EMI
C37
0.1
F:CHIP
4
5
C33
0.1
F:CHIP
FL7
EMI
-9.5
0
5.2
5.2
0
5.2
7.9
9.8
3.0
4.2
3
5
MASTER_TX(1/4)
C36
0.1
F:CHIP
2
6
C32
0.1
F:CHIP
EMI
C313
0.01
F:CHIP
1
7
FL9
7.8
9.8
2.9
4.3
-5.3
-9.5
9.4
0
4
GND
C31
0.1
F:CHIP
3
DI
EMI
2
DO/RI
0
3.8
1
DE
8
0
5.2
0
5
DO/RI
5.2
3.8
6
4
VCC
RE
4
7
3
RO
3
8
2
DO/RI
0
DE DO/RI
0
DI
GND
5.2
2
VCC
RE
1
1
RO
5V-2
16 15 14 13 12 11 10 9
5.2
M/S SELECT(1/4)
SLAVE_TX(1/4)
IC28
MAX202CSE-TE2
RS232C INTERFACE
C34
0.1
F:CHIP
FL10
R22
10k
:CHIP
Q8
DTC144EK-T146
0 MASTER/SLAVE SW
IC27
MAX202CSE-TE2
RS232C INTERFACE
IC26
LTC485CS8-E2
RS485 INTERFACE 5V-2
5V-2
REM6
D+5V
REM1
IC25
LTC485CS8-E2
RS485 INTERFACE
C
D
11-32
E
F
G
H
BC (3/4)
BC (3/4)
V SEL
(1/4)
H SEL
(1/4)
IC111
MC74HC4053F
SWITCH
Q6
2PR
2.6
0
8
1.7
D7
Q7
D8
Q8
D9
Q9
LD
OE
GND
CK
A5
A9
A4
A11
A3
OE
A2
A10
A1
CS
A0
D7
D0
D6
D1
D5
D2
D4
GND
D3
A9
A11
A10
5V
+5V
0.5
R124
3.3k
:CHIP
R126
Q108
1k 2SC2412K-TR
:CHIP
BUFFER
R123
4.7k -0.3
:CHIP
R125
4.7k
:CHIP
A
B
H
C
QH
D
G
CK1
F
CK2
E
GND PRESET
S/L
1
2
3
4
5
6
7
8
R128
2.2k
:CHIP
-0.1
LPF101
D0
18
16 15
0.5
13 12
10
R127
1k
:CHIP
D1
D2
D3
Q109
2SA1037K-TR
BUFFER
0
5V
-5.3
5.2 8
IC122(3/6)5.2
TC74VHC04F(EL)
INVERTER
Q02.2 9
Q12.8 10
Q22.3 11
Q111
2SC2412K-TR
Y BUFFER
R129
4.7k -5.3
:CHIP
8
4.6
D103
MA111-TX
Y SWITCH
IC115(1/3)
TC74VHC10F
3INPUT NAND
5.2
INT SG EN
+5V
5
Q110 (1/4)
DTA144EK-T146
INT SIGNAL SW
3
R131
100
:CHIP
D104
MA111-TX
Y OUT
-1.8
4
R130
100k
:CHIP
2.6
6 11 7 8
R132
22k
:CHIP
IC121(5/6)
TC74VHCU04F(EL)
INVERTER
Y
B
5
3
Z0
Z1
Z
C
R193
1M :CHIP
IC121(4/6)
TC74VHCU04F(EL)
INVERTER
9
IC63(3/3)
MC74HC4053F
SWITCH
X103
14.5MHz
5
4
3.5
9
C115
22p
CH:CHIP
1.8
5
1.7 3
8
Z0
Z1
C
C116
22p
CH:CHIP
IC119(3/3)
MC74HC4053F
SWITCH
0
1.9
3.5
VCC
IC113
TC74VHC74F(EL)
SAD BLANKING
IC122(1/6)
TC74VHC04F(EL)
INVERTER
2
7
2
3
1
4
12
11
13
10
Q116
DTC144EK-T146
525/625 SWITCH
14
1D VCC 1Q
1Q
1CK
2Q
1CLR
1PR
2Q
2D
2CK
2CLR
2PR GND
7
R133
4.7k
:CHIP
5.2
14
5
5
5.2 3
6
6 0
4
9
5.2
7
8
IC115(2/3)
0
-5.3
-1.9
TC74VHC10F
3INPUT NAND
5V
Q113
2SC2412K-TR
PR BUFFER
R137
100
:CHIP
Q112
2SC2412K-TR
PR BUFFER
R135
100
:CHIP
D106
MA111-TX
PR OUT
+5V
-5.3
-1.8
R136
D105
22k
MA111-TX
PB/PR SWITCH :CHIP
C377
2.2
F:CHIP
R134
100k
:CHIP
-5V
D107
MA111-TX
PB OUT
IC63(1/3)
MC74HC4053F
SWITCH
-5V
5.2
A VEE GND
IC117(1/4)
TC74VHC00F(EL) D13
NAND
MA111-TX
2
1
SAD BLANKING
7
5
Q
1
0
0
9
10
5.2
D112
MA111-TX
SAD GREEN
5
4
D111
MA111-TX
SAD RED
5.2
R139
4.7k
:CHIP -5.3
R141
D108
MA111-TX 100 -5.3
SWITCH :CHIP
≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠
CHAR_BLANK
(4/4)
CHAR_R
≠≠≠≠≠≠
≠≠≠≠≠
≠≠≠≠≠≠
CHAR_G
≠≠≠≠≠
≠≠≠≠≠≠
CHAR_B
≠≠≠≠≠
6
IC117(2/4)
TC74VHC00F(EL)
NAND
RD
≠≠≠≠≠≠≠≠≠≠
CHAR_BLANK
≠≠≠≠≠≠≠≠≠
3
0
Rx
Q
Q114
DTA144EK-T146
EXT.INT SIG SW
-1.7
D109
MA111-TX
Y OUT
R140
100k
:CHIP
≠≠≠≠≠ (4/4)
CHAR_R
≠≠≠≠≠≠
≠≠≠≠≠ (4/4)
≠≠≠≠≠≠
CHAR_G
≠≠≠≠≠ (4/4)
≠≠≠≠≠≠
CHAR_B
D113
MA111-TX
SAD BLUE
Q115
2SC2412K-TR
Y BUFFER
Y/G (4/4)
-5V
VITC_DTSE
(1/4)
SENSE (1/4)
CS (1/4)
RD/WR
(1/4,2/4)
D00-D07
(1/4,2/4)
RD
WR
D00
D01
D02
D03
D04
D05
D07
5V-2
D06
11
SIGNAL GENERATOR,INTERNAL SIGNAL DATA,PLL
(3/4) CLOSED CAPTION DISPLAY,COUNTER,D/A CONVERTER
BC
B-SS3280<AEP>-BC.-P3
11-33
B
C
A4
A3
A2
A1
CN7
40P
B TO B
A0-A4
(1/4)
5V
GND
5V
GND
5V
GND
5V
GND
A0
D07
A1
D06
A2
D05
A3
D04
A4
D03
Y IN
D02
VITC-DTSE
D01
H SIN
D00
RCS1
NC
NC
NC
SENCE
CS
CK IN
WR
NC
RD
525/625
NC
GND
5V
GND
5V
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A0
5V-2
A
4
EXT.INT.SG.EN
(1/4)
SAD DISP
(1/4)
SAD BLK DISP
(1/4)
5.2
0
6
PR/R
(4/4)
DAC_ENABLE
(1/4)
INT. SG.
(4/4)
5V
IC61(2/2)
TC74VHC123AF
SDI CC PULSE GEN
Cx
PB/B
(4/4)
R138
22k
:CHIP
X 14
X0
X1
1.9
R106
2.7k
:CHIP
1
5.2
16
12
13
14
1.7
Q52
2SC2412K-TR
BUFFER
2.1
0 9
R189
10k
:CHIP
D+5V
1.4
5V-2
4
Z
5V-2
R104
47k
:RN-CP 2.0
R105
2.7k
:RN-CP
15
3.3
C106
10p
CH:CHIP
Y0
Y1
1.7
8
C105
15p
CH:CHIP
2
1
6 11 7 8
SDI CC
(1/4)
2
9
4.6
0 6
IC122(2/6)
TC74VHC04F(EL)
INVERTER
3
R122
15k
:CHIP
3.0
R119
R120
10k
10k
:CHIP :CHIP
Q107
2SC2412K-TR
BUFFER0.4
IC117(3/4)
TC74VHC00F(EL)
NAND
9
IC122(4/6)
TC74VHC04F(EL)
INVERTER
SYNC ON/OFF
(1/4)
10 9
D7
D6
D5
D4
D3
Q2
2CK
D+5V
5.1
2D
1PR
VCC
5.2
2CLR
0.5
0.1
9 10 11 12 13 14
8
1
2
2Q
3
GND
1CK
4
5
6
2Q
7
2.4
1.8
5.8
9 10 11 12 13 14
R204
15k
:CHIP
R121
2.2k
:CHIP
2.4
D/A LEVEL
5.1
15 16 17 18 19 20 21 22 23 24 25 26 27 28
1
2
3
4
5
6
7
8
14 13 12 11 10 9
10 11 12 13 14 15 16 17 18
1
2
3
4
5
6
7
8
9
1
2
Q5
D6
0
3
D5
A8
C111
2.2
16V
F:CHIP
R118
3.3k
:CHIP
-5V
16 15 14 13 12 11 10 9
Q4
A13
A6
8
D4
A0
A1
A2
A3
A4
A5
A6
A14
A7
VCC
7
Q3
A12
SA
C112
2.2
16V
F:CHIP
R117
10k
:CHIP
5V-2
D7
D6
D5
D4
A14
A13
6
Q2
D3
Q0
Q1
Q2
VCC
C
Q106
2SA1037K-TR
BUFFER
RV101
10k
C117
0.01
F:CHIP
5V-2
VPP
GND
R116
22k
:CHIP
5V
R203
22k
:CHIP
R113
3.3k
:CHIP
5
D2
A12
H0
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
VEE
0
A
5.2
B
0
0.5
0.5
1.9
0.5
C110
0.01
F:CHIP
C109
0.1
25V
F:CHIP
4
4
DVSS
3
5
IREF
AVSS
CLK
2
6
DVSS
VB
1
7
9 10 11 12
3.3
VG
2.2
2.2
VREF
EN
1
16 15 14 13 12 11 10 9
8
BLK
X0
8
AVDD
D7
X1
Z0
7
7
D6
0
X
Z
6
6
AVDD
Z1
5
5
IO
D5
Y
4
24 23 22 21 20 19 18 17 16 15 14 13
4
3
D+5V
2
3
D4
Y0
-5V
Q51
2SC2412K-TR
IC62
TC7S86F
BUFFER
EXCLUSIVE OR
R103
2.7k
:CHIP
1
8
1Q
1D
10
100k
:CHIP
IO
VCC
12
4
16 14 15
4.9 1
2
A14
A13
A12
28 27 26 25 24 23 22 21 20 19 18 17 16 15
IC122(6/6)
TC74VHC04F(EL)
INVERTER
1Q
1CLR
IC119(2/3)
MC74HC4053F
SWITCH
4 4.2
4.9 R102
V0
5V-2
IC108
HN27C256AG-10
INT SIGNAL DATA
9 10 11 12 13 14
5.2 5
1
VDD Cx Rx
Q 130.2 2
3
Q 4
5V-2
VSS RD
D3
8
14 2.4
12
13
2.6
D+5V
R101
5.6k
C51
:RN-CP
470p
CH:CHIP
D4
GND
7
IC123
5V-2TC74VHC74F(EL)
5V-2
D FLIP FLOP
5V-2
IC61(1/2)
TC74VHC123AF
SDI CC PULSE GEN
HP5
HP6
HP7
15
C118
0.0047
B:CHIP
R159
3.3M
:CHIP
D2
6
A VEE GND
D5
5
13
X
D6
D1
4
R109
10k
:CHIP
C104
0.22
16V
B:CHIP
R191
1M
:CHIP
B
VCC
D7
D0
3
R110
18k
:CHIP
X101
14.31818MHz
Y
IC119(1/3)
MC74HC4053F
16 SWITCH
X0
X1
A0
2
0.3
R201
0.5
10k
:CHIP 2.3
3.0
2.3
12
13
1.7
CS
1
2.4
C107
18p
CH:CHIP
9 10 11 12 13 14
D+5V
C108
10p
CH:CHIP
3
5V-2
8
0 9
VCO
VDD
R
SELECT BIAS
VCO OUT VCO
IN
VCO
FIN-A
GND
VCO
FIN-B INHIBIT
PFD
PFD
OUT INHIBIT
GND
N.C.
VDD
Q1
9 10 11 12 13 14
C
Q0
D1
8
5V-2
R111
3.3k
:CHIP
HP2
HP3
HP4
0 10
10 1.7
11
R202
4.9
RC
D0
7
Z
EP
6
Z0
Z1
3.5
470
0.3 :CHIP
IC114
12
TLC2932IPW-E20
PLL
5V-2
VCC
5
4.95
3
5V-2
ET
4
IC115(3/3)
TC74VHC10F
3INPUT NAND
A10
A1
AVDD
D3
IC110
TC74HC166AF
P/S CONVERTER
5V-2
IC63(2/3)
MC74HC4053F
SWITCH
2 Y0
1.7 1
Y1
625
OE
A2
DVDD
D2
D114
RD6.2SB
PROTECTOR
R115
1k
R114
:CHIP
200
:RN-CP
-0.2
11
4.7
R192
1M
:CHIP
A3
H1
V1
D1
IC105
CXD2343S
DOT CLK COUNTER
HP1
IC121(6/6)
TC74VHCU04F(EL) 525
INVERTER 1.8
A9
A11
A4
DVDD
4.7
4.7
5.1
3
10
A5
V3
A8
D0
0.1
5.2
HP0
R155
1k
:CHIP
A8
5V-2
D0
D1
D2
D3
D4
D5
D6
D7
H POSI
IC122(5/6)
TC74VHC04F(EL)
INVERTER
14.1875MHz
1
2
4 13
Q103
DTA144EK-T146
V SYNC SEL
C113
0.01
F:CHIP
R112
4.7k
:CHIP
0.5 X102
IC116(3/3)
MC74HC4053F
SWITCH
A0
V_POS
5V-2
Q104
DTA144EK-T146
V SYNC SEL
C114
0.01
F:CHIP
C154
0.1
B:CHIP
C157
0.1
B:CHIP
525/625
(1/4)
SEL SYNC
(1/4)
SELECT SYNC SEP
(1/4)
H≠≠≠≠≠
≠≠≠≠≠≠
SYNC
(1/4,4/4)
Q1
2
CC RESET
(1/4)
AFC P
(1/4,4/4)
R157
6.8k
:CHIP
SCOF
GND
28 27 26 25 24 23 22 21 20 19 18 17 16 15
0
2.1
0
B OUT
0.5 2.7
MODE
VSS1
CLK
A13
A6
7
G OUT
0
LALT
Q2
A14
A7
6
R OUT
VINT
RESET
1
IC125(3/6)
SN74HC05ANS
5 INVERTER
FLD
Q9
Q3
A12
5
0
C155
0.0033
B:CHIP
PSEL
IC117(4/4)
TC74VHC00F(EL)
NAND
Q4
A9
A7
A8
VCC
4
BLANKING
VDD2
CLKO
7 13
A9
Q8
VPP
3
IC125(2/6)
SN74HC05ANS
INVERTER
9
C156
0.068
5V-2 B:CHIP
AIN
COMP
0
0
Q7
5V-2
2
5.2
0
7
0
0
AOUT
LR
11
5.2
Q10
16 15 14 13 12 11 10 9
IC125(1/6)
SN74HC05ANS
1 INVERTER
VR
5.2
EXT
2.6
CLKI
2.2
LD
Q11
Q5
8
IC124
Z8622812PSC
CLOSED CAPTION
ET
GND
Q6
7
VSS2
EP
14
12
A5
A4
A6
A3
A2
A1
6
FSCI
HR
QD
5
BFO
QC
D
VCC
4
FSCO
C
V2
A7
A6
A5
A4
A3
A2
A1
A0
A9
A10
A11
5V-2
Q12
3
BLKO
QB
IC104
TC74VHC4040F(EL)
LINE COUNTER
D+5V
2
SC
QA
B
5V-2
1
≠≠≠≠≠≠
CHAR_B
≠≠≠≠≠
5.2 6
TEST
RC
A
8
5.2 8
4.7
VDO
5.0
SYNC
4.7
CK
7
≠≠≠≠≠≠
CHAR_G
≠≠≠≠≠
VDD1
VP1
VP2
VP3
6
≠≠≠≠≠≠
CHAR_R
≠≠≠≠≠
HDO
VP0
5
5V-2
0
14
5.2 2
0
2.6
IC125(5/6)
SN74HC05ANS
11 INVERTER
VCC
4
6 11 7 8
IC120
CXD1030M-T6
SYNC GEN
-5V
V≠≠≠≠≠
≠≠≠≠≠≠
SYNC
(1/4,4/4)
CC C/T
(1/4)
CC L1/L2
(1/4)
CC ON/OFF
(1/4)
≠≠≠≠≠≠≠≠≠≠
CHAR_BLANK
≠≠≠≠≠≠≠≠≠ 1.5 10
5V-2
CLR
3
R153
2.2k
:CHIP
5V-2
A VEE GND
0 10
IC109
CXD1171M-T6
D/A CONVERTER
5V-2
28 27 26 25 24 23 22 21 20 19 18 17 16 15
Y
B
R151
22k
:CHIP
R154
2.2k
:CHIP
Y0
Y1
IC106
TC74VHC163F(EL)
4BIT COUNTER
14
1
1.9
X
16 15 14 13 12 11 10 9
2.6
VCC
X0
X1
2
C151
47
16V
:HT-CP
5.1 2
1
5.1
15
1
Q152
2SC2412K
Y BUFFER
5.1 12
5.0 13
IC116(2/3)
MC74HC4053F
SWITCH
Q151
2SC2412K
Y BUFFER
5V-2
Y1
3
R152
22k
:CHIP
-0.7
IC107
HN27C256AG-10
INT SIGNAL DATA
2
Y/G
0
IC116(1/3)
5V-2
MC74HC4053F
SWITCH
16
+5V
1
5V
0.5
0
D
OPEN
11-33
E
F
G
H
5
BC (4/4)
CN1
64P
B TO B
4
G
C351
0.01
F:CHIP
+15V
C252
47
C352
16V
0.01
F:CHIP :HT-CP
5
IC51
NJM79L05A
-5V REGULATOR
C247
33
25V
:HT-CP
12V
NC 3
O
12.6
2
1 I
O
-17.7
G
FL200
D402
MA111
CURRENT LIMITER
R403
1
:CHIP
-5V
R404
1
:CHIP
C916
C918 33
0.01 25V
F:CHIP:HT-CP
R405
1
:CHIP
2
-5.3
3
6
IC52
LM2940CT-5.0
+5V REGULATOR
I
O
ANALOG +5V
R401
4.7k
:CHIP
2
R406
10k
:CHIP
R409
10k
:CHIP
R407
3.3k
:CHIP
R410
4.7k
:CHIP
G
+5V
D+5V
5.2 11
IC17(2/4)
TC74HC03AF
NAND
≠≠≠≠≠
CHAR_B
≠≠≠≠≠≠
(3/4)
5.2 6
0
3
2
1
0.5
CHAR_G
≠≠≠≠≠≠
≠≠≠≠≠
(3/4)
2
1
0
EMI
R71
1k
:CHIP
11
0
6
3
D12
RD6.2SB
PROTECTOR
10 0
EMI
D10
RD12SB
PROTECTOR
FL220
IC14
LTC490CS8-E2
RS422 INTERFACE
C402
C401
100p
100p
CH:CHIP CH:CHIP
D3
RD6.2SB
PROTECTOR
D2
RD6.2SB
PROTECTOR
EMI
-5V
5
6
VR
TP9
7
IC11(2/2)
TL082CPS
SAMPLE PULSE AMP
RXD2(1/4)
TP10
D+5V
TXD2(1/4)
VCC
RIN
ROUT RIN
DIN DOUT
GND DOUT
FL221
EMI
D+5V
FL222
EMI
FL214
EMI
8
FL223
9
CHARA (1/4)
V BLANK2 (1/4)
V BLANK1
(1/4)
5.1
0.2
5.1
4.9
0.5
EMI
D115
RD6.2SB
PROTECTOR
≠≠≠≠≠
≠≠≠≠≠≠
V
SYNC (1/4,3/4)
H≠≠≠≠≠
≠≠≠≠≠≠
SYNC (1/4,3/4)
D21
D22
D23
D24
RD6.2SB
RD6.2SB
RD6.2SB
RD6.2SB
PROTECTOR PROTECTOR PROTECTOR PROTECTOR
AFC P (1/4,3/4)
RESET (1/4)
FL5
EMI
6
7
8
JR14
0
:CHIP
FL1
5V-2
TP7
FL2
C201
100
6.3V
:HT-CP
TP8
SCLK (1/4)
EMI
INT. SG.(3/4)
D+5V
MISO (1/4)
MOSI(1/4)
EMI
R55
R53
R51
R58
1k
1k
1k
1k
:CHIP :CHIP :CHIP :CHIP
R52
R57
R54
R59
1k
1k
1k
1k
:CHIP :CHIP :CHIP :CHIP
C301
0.01
F:CHIP
L201
100µH
D+5V
D+5V
8
5.2
10
5.2
SLOT6
IC32(4/6)
SN74HC05ANS
SLOT DRIVER
11 SLOT7
0
IC32(5/6)
SN74HC05ANS
SLOT DRIVER
SLOT4
IC32(1/6)
SN74HC05ANS
SLOT DRIVER
9
0
2
5.2
1
4
5.2
3
0
6
5.1
5
2
4.8
1
4
5.2
6
5.2
SLOT5
0
IC32(2/6)
SN74HC05ANS
SLOT DRIVER
0
IC32(3/6)
SN74HC05ANS
SLOT DRIVER
SLOT2
SLOT3
0.2
SLOT0
IC33(2/6)
SN74HC05ANS
SLOT DRIVER
SLOT1
0
IC33(3/6)
SN74HC05ANS
SLOT DRIVER
5
C380
0.01
F:CHIP
C379
0.01
F:CHIP
C381
0.01
F:CHIP
C204
100
6.3V
:HT-CP
C205
100
6.3V
:HT-CP
C206
100
6.3V
:HT-CP
C207
100
6.3V
:HT-CP
C208
100
6.3V
:HT-CP
C209
100
6.3V
:HT-CP
C210
100
6.3V
:HT-CP
C211
100
6.3V
:HT-CP
C212
100
6.3V
:HT-CP
C213
100
6.3V
:HT-CP
C214
100
6.3V
:HT-CP
C215
100
6.3V
:HT-CP
C216
100
6.3V
:HT-CP
C217
100
6.3V
:HT-CP
C218
100
6.3V
:HT-CP
C219
100
6.3V
:HT-CP
C220
100
6.3V
:HT-CP
C233
100
6.3V
:HT-CP
C235
100
6.3V
:HT-CP
C236
100
6.3V
:HT-CP
C237
100
6.3V
:HT-CP
C242
100
6.3V
:HT-CP
C244
100
6.3V
:HT-CP
C245
100
6.3V
:HT-CP
C341
10
10V
:TA-CP
C342
10
10V
:TA-CP
C343
10
10V
:TA-CP
C344
10
10V
:TA-CP
C302
0.01
F:CHIP
C303
0.01
F:CHIP
C304
0.01
F:CHIP
C305
0.01
F:CHIP
C306
0.01
F:CHIP
C307
0.01
F:CHIP
C308
0.01
F:CHIP
C310
0.01
F:CHIP
C311
0.01
F:CHIP
C312
0.01
F:CHIP
C315
0.01
F:CHIP
C316
0.01
F:CHIP
C317
0.01
F:CHIP
C318
0.01
F:CHIP
C319
0.01
F:CHIP
C322
0.01
F:CHIP
C323
0.01
F:CHIP
C324
0.01
F:CHIP
C325
0.01
F:CHIP
C326
0.01
F:CHIP
C327
0.01
F:CHIP
C328
0.01
F:CHIP
C329
0.01
F:CHIP
C330
0.01
F:CHIP
C331
0.01
F:CHIP
C332
0.01
F:CHIP
C333
0.01
F:CHIP
C334
0.01
F:CHIP
C335
0.01
F:CHIP
C336
0.01
F:CHIP
C337
0.01
F:CHIP
C338
0.01
F:CHIP
C339
0.01
F:CHIP
C357
0.01
F:CHIP
C358
0.01
F:CHIP
C359
0.01
F:CHIP
C360
0.01
F:CHIP
C362
0.01
F:CHIP
C363
0.01
F:CHIP
C364
0.01
F:CHIP
C365
0.01
F:CHIP
C366
0.01
F:CHIP
C367
0.01
F:CHIP
C368
0.01
F:CHIP
C369
0.01
F:CHIP
C370
0.01
F:CHIP
C371
0.01
F:CHIP
C373
0.01
F:CHIP
C374
0.01
F:CHIP
C394
0.01
F:CHIP
C309
0.01
F:CHIP
14
13
C321
0.01
F:CHIP
GND
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
+12V
TALLY
OVERLOAD
STANDBY
POWER
+5V
H SYNC
V SYNC
RTS(OPTION)
GND
N.C.
RXD(OPTION)
+5V
TXD(POTION)
GND
TXD
RXD
GND
+5V
GND
TXD
RXD
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
GND
GND
TO TB BOARD
CN5
R56
10k
12 :CHIP
5.2
7
R300
10k
:CHIP
R301
10k
:CHIP
14
11
IC34
9
8
5.2
13
10
5.2
IC33(4/6)
IC33(5/6)
SN74HC05ANS SN74HC05ANS
SLOT DRIVER SLOT DRIVER
FL6
EMI
(4/4)
BC
SLOT RECIVER
R302
10k
:CHIP
SAMPLE PULSE GEN
CURRENT LIMITER
RS422 INTERFACE
CHARACTOR OUT
12
5.2
7
IC33(6/6)
SN74HC05ANS
SLOT DRIVER
D+5V
D403
RD6.2SB
PROTECTOR
11-34
B
C320
0.01
F:CHIP
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A21
B21
A22
B22
A23
B23
A24
B24
A25
B25
A26
B26
A27
B27
A28
B28
A29
B29
A30
B30
A31
B31
A32
B32
IC32(6/6)
SN74HC05ANS
SLOT DRIVER
SLOT
(1/4)
D+5V
14 MC74HC30FEL
SLOT RECEIVER
8
*
7
EMI
C203
100
6.3V
:HT-CP
SLOT (1/4)
5.2
12
5.2 11
5.2 6
5.2 5
5.1 4
4.8 3
5.2 2
5.2
1
FL205
C202
100
6.3V
:HT-CP
C340
0.01
F:CHIP
IC33(1/6)
SN74HC05ANS
SLOT DRIVER
0
3
C378
0.01
F:CHIP
5
A
+12V
FL212
D11
RD12SB
PROTECTOR
RD
0
4
EMI
CHARA-1 (1/4)
IC8(3/6)
SN74HC05ANS-E05
INVERTER
11 12 13 14 15 16 17 18 19 20
1
2
3
VG
FL213
OPTION_TXD
(2/4)
Cx
0
IC35
TC74VHC541F(EL)
OCTAL BUFFER
4
9
D6
RD12SB
PROTECTOR
D7
RD12SB
PROTECTOR
D8
RD12SB
PROTECTOR
D9
RD12SB
PROTECTOR
9
VB
EMI
EMI
OPTION_RXD
(2/4)
CHARA-3 (1/4)
11
8
POWER
(1/4)
FL211
IC16(2/2)
TC74VHC123AF(EL)
SAMPLE PULSE GEN
VCBLK
5
16V
:HT-CP
EMI
FL204
C404 1.2
22
6.3V
:HT-CP
Q401
2SC2412K
CURRENT LIMITER
0
IC8(2/6)
SN74HC05ANS-E05
INVERTER 5.2
D+5V
6
Rx
Q
C407
IC401(2/2)
4
0.01
3.5
LM393PS-E2
F:CHIP
CURRENT LIMITER
IC401(1/2)
LM393PS-E2
C403
C405
10
CURRENT LIMITER
0.01 C406
STBY
(1/4)
EMI
OPTION_RTS
(2/4)
IC16(1/2)
TC74VHC123AF(EL)
SAMPLE PULSE GEN
5.0 12 Q
IC8(5/6)
SN74HC05ANS-E05
INVERTER 5.2
5
7
0 5
5.2 10
IC8(4/6)
SN74HC05ANS-E05
INVERTER 5.2
8
C11
R24
0.001
1k
CH:CHIP
R25 :RN-CP
1k
:RN-CP
5.2
75.2
FL3
VSS
3
14
5.2 3
RD
FL210
0.1
1
4.1
F:CHIP 0.01
F:CHIP
1
2
0
4Q
R26
1k
:RN-CP
8
4
IC17(1/4)
TC74HC03AF
NAND
13
IC11(1/2)
TL082CPS
SAMPLE PULSE AMP
8
3
2
8
IC17(4/4)
TC74HC03AF
NAND
Rx Cx VDD
Q
0
EMI
FL203
7
≠≠≠≠≠≠≠≠≠
CHAR_BLANK
≠≠≠≠≠≠≠≠≠≠
(3/4)
1.5k
:RN-CP
R408
10k
:CHIP
7
1
CHAR_R
≠≠≠≠≠≠
≠≠≠≠≠
(3/4)
PB/B
(3/4)
R402
10k
:CHIP
5
6
2
Y/G
(3/4)
5.2 8
C10
0.001
CH:CHIP
5.2
15 14 16
5.2 R72
9
10
12
13
0
5
4
3.5
R23
1k
:RN-CP
CHARA-2
(1/4)
IC17(3/4)
TC74HC03AF 0
NAND
R14
1k
:CHIP
5.2
0.2
4.5
4.9
0.5
Q403
2SD1834-T101
1.3 CURRENT
LIMITER
FL202
6
R13 R12 R15
1k 1k 1k
:CHIP:CHIP:CHIP
OVERLOAD
(1/4)
5
5.3
Q9
2SD1834-T101
TALLY DRIVER
C12
0.01
F:CHIP
R411
Q402
100k
:CHIP 2SC2412K
CURRENT LIMITER
1.9
3
R36
2.2k
:CHIP
R37
2.2k
:CHIP
R38
2.2k
:CHIP
PR/R
(3/4)
5V
3
1
6.8
C241 C243
C248
100 1000 C391 100 C393
6.3V 6.3V 0.01 6.3V 0.01
:HT-CP :HT F:CHIP :HT-CP F:CHIP
4
C231
100
6.3V
:HT-CP
0
R64
6.8k
:CHIP
3
+6V
11.2
R63
2.2k
:CHIP
TALLY
(1/4)
9
EMI
R69
0
:CHIP
RY401
1 5 4 8 7 10
-5V
2
-15V
FL201
D401
MA111
CURRENT LIMITER
D+5V
C291 C232 C234
47
100
100 C372 C376
16V 6.3V 6.3V 0.01 0.01
:HT-CP :HT-CP :HT-CP F:CHIP F:CHIP
+12V
EMI
TP1 TP3 TP11 TP12 TP13
6
3
3.4 4
16.9
1 IVC
7
2
C251
33
25V
:HT-CP
8
A1
GND
B1
GND
A2
+B
B2
+B
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
VIDEO
P.Y. OUT A9
P.C. OUT B9
A10
GND
B10
Y/G
A11
GND
B11
PB/B
A12
GND
B12
PR/R
A13
SLOT_6
B13
SLOT_7
A14
SLOT_4
B14
SLOT_5
A15
SLOT_2
B15
SLOT_3
A16
SLOT_0
B16
SLOT_1
A17
GND
CHAR_BLANK B17
A18
CHAR_G
B18
CHAR_B
A19
CHAR_R
AFC PULSE B19
A20
H SYNC
B20
V SYNC
2H SYNC A21
2V SYNC B21
A22
N.C.
B22
N.C.
A23
N.C.
B23
N.C.
A24
N.C.
V BLANK1 B24
H BLANK A25
V BLANK2 B25
A26
N.C.
B26
RESET
SAMPLE PULSE A27
B27
MISO
A28
MOSI
B28
SCLK
DIGITAL +5V A29
DIGITAL +5V B29
DIGITAL GND A30
DIGITAL GND B30
A31
N.C.
INT. SG. B31
A32
GND
B32
GND
TO TB BOARD
CN1
CN2
64P
B TO B
+12V
IC37
R73
100k
PQ12TZ5U
:CHIP +12V REGULATOR
10 9
1
BC (4/4)
C
D
11-34
E
F
G
H
BC
BC
BC Board IC Block Diagrams
2
6.5Vp-p (20MHz)
4
CXD1171M (IC109)
3
6.4Vp-p (4.9152MHz)
5
7.3Vp-p (14.1875MHz)
6
VPP
1
32 VCC
A16
2
31 WE
A15
3
30 A17
A12
4
29 A14
A7
5
A6
6
A5
7
A4
8
A3
9
DELETE
VOLTAGE SWITCH
VOLTAGE
SW
X-DECODER
262, 144BIT
MEMORY ARRAY
Y-DECODER
Y GATE
ADDRESS
LATCH
PROGRAM VOLTAGE
SWITCH
COMMAND
REGISTER
A2 10
CE, OE
LOGIC
DATA
LATCH
SENSE
AMP
A1 11
7
7.5Vp-p (14.53MHz)
8
5.1Vp-p (H)
9
1
24 DVDD
D1
2
23 DVDD
D2
3
D3
4
D0
28 A13
D4
5
27 A8
D5
6
26 A9
D6
7
25 A11
D7
8
24 OE
BLK
9
23 A10
22 CE
21 D7
A0 12
11.6Vp-p (14.32MHz)
LTC485CS8 (IC25, 26)
22 AVDD
DECODER
LATCHS
21 IO
6MSB'S
CURRENT
CELLS
DE
3
DI
4
R
D
CLOCK
GENERATOR
13 B GND
16
Vcc
15
GND
3
14
T1OUT
C2+
4
13
R1IN
C2-
5
12
R1OUT
V-
6
11
T1IN
T2OUT
7
10
T2IN
R2IN
8
9
R2OUT
C1+
1
V+
2
C1-
18 D4
17 D3
ENT
1
EMP
2
ENT
EMP
D0
3
D0
Q0'
26 Q0
D1
4
D1
Q1'
25 Q1
D2
5
D2
Q2'
24 Q2
D3
6
D3
Q3'
23 Q3
D4
7
D4
Q4'
22 Q4
20 COMP
D5
8
D5
Q5'
21 Q5
18 PSEL
D6
Q6'
20 Q6
Q7'
19 Q7
CXD1030M (IC120)
FSCI 24
1/4
28 VDD
26 SC
FSCO 25
7.4Vp-p (10MHz)
1/5
PHASE
COMPARATOR
1/227
A
GND
14 A GND
20 D6
5Vp-p (V)
6
5
MAX202CSE (IC27, 28, 36)
15 IREF
CURRENT
CELLS
(FOR FULL SCALE)
VB 11
19 D5
IN/OUT BUFFER
B
17 VG
D1 14
D2 15
VCC
7
18 AVDD
D0 13
GND 16
8
16 VREF
27 C0
10-BIT BINARY COUNTER
MC74HC4053F (IC63, 111, 116, 119)
9
D6
D7 10
D7
X1
1
D8 11
D8
Q8'
18 Q8
X0
2
D9 12
D9
Q9'
17 Q9
Y1
3
14 ZC
LD 13
LD
YC
4
13 Z1
Y0
5
EN
6
11 AZ
VEE
7
10 AX
GND
8
16 VDD
1/4
CLKI 10
SUB-CARRIER
CONTROL
CLKO 11
1/7
or 6
15 SCOF
1/526
or 625
1/65
H
DECODER
V
DECODER
TEST
GENERATOR
27 TEST
16 OE
GND 14
15 CK
15 XC
OPEN
12 Z0
AIN 21
OPEN
V
CONTROL
AOUT 22
RESET
GENERATOR
OUTPUT CONTROL
9
9
MODE
VINT
LR
VR
HR
EXT
D7
D6
D5
D4
D3
D2
D1
D0
17 8 7 6
WR
RD
DS
R/W
AS
16
AY
OPEN
TMO
IRQ1/ADTRG
IRQ0
WAIT
BREQ
BACK
E
13 12 5 4 3 2 1
LALT
FLD
BFO
BLKO
SYNC
VDD
HDD
HD6475368CP (IC1)
10 9 8 7 6 5 4 3
15 14 13 12 11
37 31 30 29 28 27 26 25
PORT
PORT
PORT
MM1026BFB (IC2)
A1
A0
CS
RD
WR
GND
RST
CLR
D7
D6
D5
D4
D3
NC
NC
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
EXTAL 84
XTAL 1
CLOCK
OSCILLATOR
CONTROL
32 D2
PX2 52
8
31 D1
8
PA1 55
LATCH
PA2 56
8
VDD
LATCH
LATCH
25 GND
8
8
LATCH
24 PD4
8
23 PD3
8
PA6 62
22 PD2
21 PD1
PA7 63
DATA
SELECT
PB0 64
VCC
VCC
VSS
VSS
VSS
VSS
VSS
VSS
PB2
PB3
PB4
PB5
PB6
12
13
14
15
16
17
18
19
NC
PB1
11
PC7
NC
10
PC6
NC
9
PC5
8
PC4
7
PC3
6
PC2
5
PC1
4
PC0
3
PB7
2
GND
1
16
55
2
24
41
42
64
83
16 BIT FREE-RUN
TIMER
(X 3-CH)
PWM TIMER
(X 3-CH)
20 PD0
AVCC
AVSS
BIT TIMER
SERIAL
COMMUNICATION
INTERFACE
(X 2-CH)
26 VDD
8
PA4 60
PA5 61
A15
A14
A13
A12
A11
A10
A9
A8
NMI 22
27 PD5
8
8
50
49
48
47
46
45
44
43
28 PD6
8
58
PA3 59
A7
A6
A5
A4
A3
A2
A1
A0
10-BIT
A/D CONVERTER
(X 8-CH)
74
65
GND
1
RESET
2
CS
3
VBATT
WATCH DOG TIMER
PORT
PORT
PORT
82 81 80 79 78 77 76 75
73 72 71 70 69 68 67 66
63 62 61 60 59 58 57 56
11-35
4.2V VOLTAGE
DETECT CIRCUIT
4
8
VCC
7
NC
6
V
5
CS
54
53
52
51
PW3/IRQ5/A19
PW2/IRQ4/A18
PW1/IRQ3/A17
IRQ2/A16
TC74HC151AF (IC19-21)
D3 1
16 VCC
D2 2
D2 D3 D4
15 D4
D1 3
D1
D5
14 D5
D0 4
D0
D6
13 D6
Y 5
Y
D7
12 D7
XY 6
W
A
11 A
OE 7
S
B
10 B
C
GND 8
9 C
TC74VHC138F (IC10, 13)
Vcc
Y0
Y1
Y2
Y3
Y4
Y5
T6
16
15
14
13
12
11
10
9
Y0
Y1
Y2
Y3
Y4
Y5
C
G2A
G2B
G1
Y7
A
B
11-35
3.3V VOLTAGE
DETECT CIRCUIT
CPU
DATA
TRANSFER
CONTROLLER
29 PD7
8
GND 57
WEDGE IN
CONTROLLER
30 D0
8
40
39
38
37
36
35
34
33
PORT
8
PROM/MASK ROM
62k BYTE (H 8/536)
FTAO1
FTOB3/FTCI3
FTOB2/FTCI2
FTOB1/FTCI1
FTI3/TMRI
FTI2
FTI1
TMC1
LATCH
PA0 54
RAM
2k BYTE
AN7
AN6
AN5
AN4
AN3
AN2
AN1
AN0
8
WAIT
STATE
CONTROLLER
SCK1
RXD1
TXD1
SCK2/PW3
RXD2/PW2
TXD2/PW1
FTOA3
FTAO2
8
PX3 53
RES 21
STBY 20
MD0 17
MD1 18
MD2 19
PORT
A2
49
PORT
PX0
50
ADDRESS BUS
PX1
51
DATA BUS (HIGH RANK)
NC
CXD1095BQ (IC5, 6)
DATA BUS (LOW RANK)
!º
5Vp-p (V)
2
19 AVDD
2LSB'S
CURRENT
CELLS
CXD2343S (IC105)
5Vp-p (H)
1
RE
20 IO
DECODER
D GND 10
CK 12
RO
VOLTAGE
DOUBLER
1
CAT28F020P-15 (IC3)
VOLTAGE
INVERTER
BC Board Waveforms
Y6
1
2
3
4
5
6
7
8
A
B
C
G2A
G2B
G1
Y7
GND
BC
µPD71051GU-10E2 (IC22-24)
TC74VHC4040F (IC30, 104)
H
K RD
J
Q
J
Q
Q3
5
J
Q
Q4
3
J
Q
Q5
2
J
Q
Q6
4
J
Q
Q7
13
J
Q
Q8
12
J
Q
Q9
14
J
Q
Q
Q10
15
J
Q
Q11
1
J
CK 10
K RD
K RD
K RD
K RD
K RD
K RD
K RD
K RD
K RD
K RD
RD 11
16
VCC
1
2
19 G2
A2
3
18 Y1
CLR1
1
14 VCC
D1
2
13 CLR2
CLK1
3
PR1
4
Q1
5
Q1
6
9
Q2
GND
7
8
Q2
CLR
D
RECEIVE
DATA BUFFER
TRANSMISSION
DATA BUFFER
16 Y3
6
15 Y4
A6
7
14 Y5
A7
8
13 Y6
A8
9
12 Y7
GND 10
11 Y8
TX DATA
TX RDY
TX EPP
TX CLK
RECEIVER
13
14
16
25
RD
RX RDY
SYNC/BRK
RX CLK
MODEM
CONTROLLER
17
23
24
22
CTS
RTS
CONTROLLER
Q
CLK Q
PR
CLK Q
CLR
10 PR2
Z8622812PSC (IC124)
15
14
SLICAD DATA
DATA
SLICER
CVI 11
DCLK
DISPLAY
RAM
TIMING
LOGIC
COMP SYNC
SELECT
VCO
OUT
FIN-A
FIN-B
PFD
OUT
LOGIC
GND
2
3
4
5
6
7
DATA MOD
&
XFR BUF
SYNC
SLICER
TLC2932IPW (IC114)
1
DATA
RECOVARY
DATA CLK
RECOVARY
CLAMP
SSL 12
LOGIC
VDD
LOCK
COMMAND PROCESSOR
AND
DECODER CONTROL
VARTICAL CTR
AND CONTROL
CHAR
ROW
HORIZONTAL
COUNTER
DOT CLK
OUTPUT
LOGIC
14
13
12
11
10
9
8
VCO
VDD
R BIAS
VCO
IN
VCO
GND
VCO
INHIBIT
PFD
INHIBIT
NC
PHASE
FREQ
DET.
LOOP
FILTER
8
13
9
10
16 1 17 18 2
HLF
VSS
(DIGITAL)
VSS
ANALOG
NSIN
DONF/SEN
CT/SDA
LNG/SCK
NRESET
PFD
HFI
1/2 DIVIDER
VCO
VCO
µPD6453GT-101-E1 (IC7)
BUSY
1
CLY
2
CS
DATA
3
4
PCL
5
DATA INPUT
SHIFT REGISTER
INSTRUCTION
DECODER
•
•
•
•
CONTROL SIGNAL
20 HSYNC
VDD
6
CK OUT
7
OSC OUT
8
DATA BUFFER
REGISTER
SYNC
PROTECTION
19 VSYNC
CHARACTER
SIZE REGISTER
H. ADDRESS
REGISTER
WRITE ADDRESS
COUNTER
VIDEO RAM
DATA
SELECTOR
HORIZONTAL
SIZE COUNTER
H. POSITION
COUNTER
H. ADDRESS
COUNTER
OSCILLATOR
OSC IN
9
VSS
10
CHARACTER
DATA
COLOR
DATA
PRINT
DATA
8 bit
X
288 word
3 bit
X
288 word
1 bit
X
288 word
BACK
GROUND
CONTROL
DATA
REGISTER
DISPLAY
CONTROL
DATA
REGISTER
18 B BLX
17 C BLX
16 R BLX
CHARACTER CHARACTER
GENERATOR GENERATOR
RAM
ROM
V. ADDRESS
REGISTER
TIMING
GENERATOR
VERTICAL
SIZE COUNTER
V. POSITION
COUNTER
DTR
DSR
CS 11
VDD
DIGITAL
5
A5
D
19
15
18
9
12 D2
PR
Q
21
20
12
13
10
TRANSMITTER
11 CLK2
17 Y2
A4
RESET
CLK
C/D
RD
WR
TC74VHC74F (IC113, 123)
20 VDD
4
26 VDD
4 GND
SYNCHRONOUS
CHARACTER
REGISTER
CONTROL
WORD
REGISTER
A1
A3
STATUS
REGISTER
D0 27
D1 28
D2 1
D3 2
D4 5
D5 6
D6 7
D7 8
8
GND
TC74VHC541F (IC29)
G1
K RD
Q
STASUS BUS
J
Q2
6
VDD
ANALOG
H
Q1
7
INTENAL 8 BIT BUS
Q0
9
BC
V. ADDRESS
COUNTER
12X18 bit
X
16 word
12X18 bit
X
240 word
15 VCBL
14 VB
OUTPUT
CONTROLLER
13 VC
12 VR
11 MP
11-36
11-36
5
6
7
4
3
R
G
B
LUM
BOX
E (1/4)
C966
0.47
25V
F:CHIP
C968
0.47
25V
F:CHIP
C970
0.47
25V
F:CHIP
Q807
DTC144EKA-T146
HV OCP SW
1
WP
SCK
VSS
SI
-2
C862
100p
5V-2 R802 R803
CH:CHIP
100k 100k
L SCLK(2/4,4/4)
:CHIP :CHIP
R859
R855
100k
100k
L MOSI(2/4,4/4)
:CHIP R854 :CHIP
R853
100
100
:CHIP
R804
IC801(1/4)
:CHIP
100k
HP (3/4)
:CHIP MC74HC125AF
V BLK P1
R801
BUFFER
100k
* 5
H BLK P
:CHIP
6 *
IC801(2/4)
MC74HC125AF
BUFFER
4
R806
100
:CHIP
13
14
5.1 2
*
R818
10k
:CHIP
2
IC801(4/4)
MC74HC125AF
BUFFER
R817
100k
:CHIP
R809
4.7k
:CHIP
VCC
IC802
MB89613R-438
SUB
MICRO COMPUTER
PA40
PA41
PA42
PA43
PA44
1
2
3
4
5
6
7
8
VSS
12
X1
X0
MOD1
MOD0
RESET
9 10 11 12 13 14 15 16 17 18 19
0
0
32
31
30
29
28
27
26
25
24
23
22
21
20
R641
270k
:CHIP
(4/4)
LD CV
LD BLK
(1/4)
4
C642
10
Q641
2SC2412K
CLAMP
R642
10k
:CHIP
5.2
4
5
D642
RD3.0SB-T1
LIMITER
D641
RD3.0SB-T1
LIMITER
C644
1
16V
F:CHIP
CY(H)RTN
(4/4)
CY(H)
(4/4)
HV PROT
(2/4)
HV RTN(AC)
(2/4)
ABL2
(2/4)
HV RTN(DC)
(2/4)
+15V-2
(2/4)
ABL1
(2/4)
15V
H SYNC
(3/4)
8
5.2
6
7
3.3
8
4.8
7
5V-2
5
6
H STAT
(2/4)
G2 CNT
R634
47k
:CHIP
12V
4.8
7
0.6
R651
10k
:CHIP
V TIM (3/4)
Q622
DTC144EKA
INVERTER
R650
10k
:CHIP
-12V
3.1
V.SP
8
2.2
9
I V.SP (2/4)
IC628(4/6)
TC74VHC14F(EL) 4.8
INVERTER
IC627(4/6)
8
TC74VHC14F(EL)
5V-2 INVERTER
14
4.3
0.5 10
11
I AFC P (3/4)
9
-12V
AFC P
7 -2
4.8
IC628(3/6)
TC74VHC14F(EL)
INVERTER
IC627(6/6) R653
TC74VHC14F(EL) 100
:CHIP
INVERTER
2HS
5
6
0 1
5.3
2
-2
HS
IC627(3/6)
TC74VHC14F(EL)
INVERTER
2VS
X801
8MHz
13
4.5 3
5.1
5.1
4 0.1
-2
D801
RD5.6SB-T1
DC LEVEL SHIFT
R652
100
:CHIP
IC627(2/6)
TC74VHC14F(EL)
INVERTER
-2
5V-2
0.4
0.4
-20.2
IC627(1/6)
12 TC74VHC14F(EL)
INVERTER
IC627(5/6)
TC74VHC14F(EL)
INVERTER
IC625
MC74HC4053FEL
H/V SYNC SELECT
5V-2
14
5.013
12
7
VS
-2
9 10 11 12 13 14 15 16
1
2
3
4
5
6
7
11
R629
10k
:CHIP
C625
560p
CH:CHIP
R649
10k
:CHIP
C643
10
7 0
:CHIP
-12V
3
4.9
12
IC622(2/2)
LM393PS-E20
VS P PHASE
+12V
R646
10k
:CHIP
2
9
13
5.1
10
9
IC622(1/2)
LM393PS-E20
HS P PHASE
R648 6.4
4
R647 10k 6.4
10k :CHIP
R645
10k
:CHIP
1
14
0.2
Q2
9
8
14
10
R627
10k
:CHIP
15
1
6.4
5
0 6
R628
10k
:CHIP
8
3
2
4
C624 C626
0.1
0.1
25V
25V
B:CHIP B:CHIP
3.8
(4.5)
C641
0.1
25V
B:CHIP
0
PA4
PA5
PA6
MB88346
S_SEL
R626
10k
:CHIP
7
6.4
IC641(1/2)
NJM4558M-TE2
-12V
SYNC GEN
12V
IC641(2/2)
NJM4558M-TE2
3
AMP 0
1
8
5.3
16
12V
-12V
5.2
HV OFF
(2/4,3/4)
4.6
+12V
8
6
5
IC623
MC74HC4538AFEL
H SYNC
GENERATOR
11
10
2.9
0.1
0
0
-2
V DELAY
H DELAY
IC628(2/6)
TC74VHC14F(EL)
INVERTER
0.15
6
V SYNC (3/4)
32b
32a
31b
31a
30b
30a
29b
29a
28b
28a
27b
27a
26b
26a
25b
25a
24b
24a
23b
23a
22b
22a
21b
21a
20b
20a
19b
19a
18b
18a
17b
17a
16b
16a
15b
15a
14b
14a
13b
13a
12b
12a
11b
11a
10b
10a
9b
9a
8b
8a
7b
7a
6b
6a
5b
5a
4b
4a
3b
3a
2b
2a
1b
1a
GND
GND
LCC.RET
LCC.RET
LCC
LCC
ROT.RET
ROT.RET
ROT
ROT
NTC.RET
NTC.RET
NTC
NTC
CY(V)RET
CY(V)RET
CY(V)
CY(V)
CY(H)RET
CY(H)RET
CY(H)
CY(H)
HV PROT
HV R(AC)
ABL2
HV R(DC)
+15V
ABL1
+15V
NC
GND
GND
H STAT C
G2.C
+12V
+12V
GND
GND
-12V
-12V
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
GND
GND
2
3
4
5.2
1a
1b
2a
2b
3a
3b
4a
4b
5a
5b
6a
6b
7a
7b
8a
8b
9a
9b
10a
10b
11a
11b
12a
12b
13a
13b
14a
14b
15a
15b
16a
16b
17a
17b
18a
18b
19a
19b
20a
20b
21a
21b
22a
22b
23a
23b
24a
24b
25a
25b
26a
26b
27a
27b
28a
28b
29a
29b
30a
30b
31a
31b
32a
32b
5V-2
C801
220
10V
17
IC801(3/4)
MC74HC125AF
BUFFER
5.3
5.3
R816
100k
:CHIP
L.SCLK
L.MOSI
-2
0
Q801
DTC144EKA-T146
RESET SW
3
R808
100
:CHIP
5.2
-2
5.3
11
R807
100
:CHIP
EMI
SCL (2/4,3/4)
SDA (2/4,3/4)
10
5.2 12
FL901
5.2
9
IC621(2/2)
TL082CPS-E20
AMP
Q815
DTA144EKA
0 PROT SW
0
6.4
6.4
R632
4.7k
:CHIP
6
5.3 8
EMI
R815 R814
4.7k 4.7k
:CHIP :CHIP
52
53
54
55
56
57
58
59
60
61
62
63
64
SCLK
MISO
MOSI
R805
100
:CHIP
FL801
R622
10k
:CHIP
51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
2
V BLK P2
5V-2
R625 R633
10k
10k
3.3 :CHIP :CHIP
C623
R630
0.001
CH:CHIP 100k
:CHIP
0.1
C621
0.001
0 CH:CHIP
R621
100k
:CHIP
:CHIP
HV CTL
(2/4)
5
HOLD
6
-2
SO
7
R856
470
:CHIP
VCC
4
R858
470
:CHIP
CS
R811 R812 R813
100k 100k 100k
:CHIP :CHIP :CHIP
8
R860
470
:CHIP
3
AFC P
HS
VS
2HS
2VS
IC803
X25040S-C7000 D+5V
EEP ROM
PROT
R825 (2/4)
10k
Q802
DTA144EKA-T146
INVERTER
H DELAY
V DELAY
5V-2
R862
1k
:CHIP
100k 100k
:CHIP :CHIP
D853
RD6.2SB
PROTECT
0
VCC
NC
VSS
SLOT_ID
R863
1k
:CHIP
Q621
2SC2412K
CLAMP
CY(V)RTN
(4/4)
D TIM
(2/4,3/4)
GND
C964
0.1
25V
B:CHIP
R823
10k
:CHIP
V BLK P
(2/4)
C622
0.1 25V B:CHIP
NTC RTN
(2/4)
(4/4)
CY(V)
C631
0.1
25V
B:CHIP
R631
12k
:CHIP
1
Q611
DTC144EKA-T146
V BLK SW
+5V
ROT (4/4)
NTC(2/4)
IC628(5/6)
TC74VHC14F(EL)
INVERTER
Q2
C962
100
16V
5V
V BLK P2
10
ROT RTN
(4/4)
0.2
Q1
IC961
LM2940CT-5.0
+5V REG
0
C612
0.1
25V
B:CHIP
1 4.6
3
2
11
IC611(2/2)
LM393PS-E20
COMPARATOR
B2
Q804
DTC144EKA-T146
POWER ON SW
V BLK B
(2/4)
(3/4)
I V SAW
V BLK P1
IC628(6/6)
TC74VHC14F(EL)
INVERTER
4.9
1
LCC (2/4)
D611
MA111-TX
4 0.3
9 10 11 12 13 14 15 16
C956
0.47
25V
F:CHIP
PROT1
PROT2
PROT3
PROT4
R852 R851
100
100
:CHIP :CHIP
R824
1k
:CHIP 0
+5V
Q2
R615
15k:RN-CP(14G1/14G5)
10k:CHIP(20G1)
Q808
DTA144EKA-T146
SW
5.3
O
G
C952
470
10V
5V R861 R857
3
5.2
5.2
5V
GND
IC628(1/6)
TC74VHC14F(EL)
INVERTER
IC621(1/2)
TL082CPS-E20
SYNC GEN
5.2
R821
D802
10k
MA111-TX :CHIP
PROTECT
G
G
G
G
G
G
G
G
0
C969
0.47
25V
F:CHIP
Q809
DTA144EKA-T146
E PROT SW
HV OVP (2/4)
IK PROT (2/4)
R865
470
:CHIP
C967
0.47
25V
F:CHIP
3
2
5.0 3
4
I
0.9
C965
0.1
25V
B:CHIP
PROT1
PROT2
PROT3
PROT4
R868
100
:CHIP
C963
470
10V
5.3
C821
10
R614
12k:RN-CP(14G1/14G5)
10k:CHIP(20G1)
4.6
H BLK W
(2/4)
0.2 2
H BLK P
VSS
G.PROT1
G.PROT2
G.PROT3
G.PROT4
DEGAUSS
POWER.ON
HV_OVP
IK.PROT
HV_OCP
AFC.SW
+B.PROT
H.DELAY
V.DELAY
V.STOP
H.STOP
ASPECT
HV CTRL
R866
470
:CHIP
R864
470
:CHIP
C961
470
10V
6V
6.8
C951
470
10V
R604
12k
:CHIP
5V-2
-5V
C613
100p
CH:CHIP
1.1
O
C981
470
10V
R867
470
:CHIP
R869
100
:CHIP
Q803
DTA144EKA-T146
POWER ON SW
-5V
Q2
Q1
4
C928 C929 C930
0.47 0.47 0.47
25V
25V
25V
F:CHIP F:CHIP F:CHIP
V STOP (3/4)
H STOP (3/4)
(2/4)
ABL
G2 CNT
C924 C925 C926
0.47 0.47 0.47
25V
25V
25V
F:CHIP F:CHIP F:CHIP
G
C976
C971 0.47
470
25V
10V F:CHIP
R872
100
:CHIP
R870
100
:CHIP
-12V
7
-5.3
I
C923
100
16V
LCC RTN
(2/4)
R618
10k
:CHIP
R617
27k
:CHIP
8
-7.0
V.SP
C873 R873
100p
1k
CH:CHIP :CHIP
C986 C987 C988
0.47 0.47 0.47
25V
25V
25V
F:CHIP F:CHIP F:CHIP
C922
100
16V
DF BLK P
(2/4)
4.8
V SAW
(3/4)
GND
IC981
LM2990T-5.0
-5V REG
-6V
L951 220µH
C921
470
16V
H +B (3/4)
+6V
7
O
G
IC921
NJM7812FA
+12V REG
R619
10k
:CHIP
4.7
-12V
3.0
8
I
R871
100
:CHIP
B2
+12V
12.7
-6V
A2
Q1
CN802
64P
B TO B
6
Q1
12V
+15V
B1
1.9
1
0
VDD
5.0
Q4
Q4
5.0
D4
D3
Q3
0.3
Q3
CK
A2
2H TIM
(2/4,3/4,4/4)
3
2
R616
18k
:CHIP
RESET2
1
C996 C997 C998 C999
0.47 0.47 0.47 0.47
25V
25V
25V
25V
F:CHIP F:CHIP F:CHIP F:CHIP
5
2
C994
100
16V
IC612(1/2)
NJM4558M-TE2
V SAW AMP
3
IC991
NJM7809FA
+9V REG
-15V
C993
100
16V
C611
0.1
25V
B:CHIP
5
C992
100
16V
R605
4.7k
:CHIP
4
RD
5.0
Q1
Q1
5.0
D1
4.9
D2
Q2
Q2
GND
B1
R601
270k
:CHIP
O
G
4
I
C916 C917 C918 C919 C920
C913 0.47 0.47 0.47 0.47 0.47
220
25V
25V
25V
25V
25V
25V F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
A1
13
H BLK PH
(2/4)
4.9
A1 RESET2
1
CX2/RX2
+9V
9.5
16.6
C602
0.0015 CH:CHIP
(14G1/14G5)
0.0022 CH:CHIP
(20G1)
4.4
1
+5V
5.1
R613
10k
8 :CHIP
7
5
8.5 6
V BLK T
(2/4)
GND
RESET1
9V
+15V
C912
220
25V
3.5
R602
22k
:CHIP
15V
C911
220
25V
CX1/RX1
12
C943
100
16V
11
C942
100
16V
2
C941
470
16V
C939
0.47
25V
F:CHIP
VCC
3
C938
0.47
25V
F:CHIP
GND
5
C936
0.47
25V
F:CHIP
2
TO TA BOARD
CN11
C933
220
25V
1
GND
GND
+B
+B
GND
GND
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
DU.G
DU.B
DU.R
V.SP
ABL
G2.CNT
HCR
VCR
H.CY
V.CY
H.STAT
V.STAT
HCT
POWER.ON
DEGAUSS
E_PROT
G.PROT1
G.PROT2
G.PROT3
G.PROT4
GND
GND
VD
AFC.P
HS
VS
2HS
2VS
NC
NC
NC
NC
H P
V.BLK.P1
H.BLK.P
V.BLK.P2
5V_SENCE
RESET
NC
MISO
MOSI
SCLK
DIGITAL_5V
DIGITAL_5V
DIGITAL_GND
DIGITAL_GND
CH_SLOT2
INTERNAL.SIG
GND
GND
C932
220
25V
C946 C947 C948 C949 C950
0.47 0.47 0.47 0.47 0.47
25V
25V
25V
25V
25V
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
6
G
C931
220
25V
C601
0.0039
25V
CH:CHIP
O
15
-12.5
I
16
-12V
-17.5
IC611(1/2)
LM393PS-E20
COMPARATOR
GND
-12V
-15V
CN801
64P
B TO B
12V
R612
12k:RN-CP(14G1/14G5)
10k:CHIP(20G1)
R611
15k:RN-CP(14G1/14G5)
10k:CHIP(20G1)
VCC
-15V
+120V
IC613
TC74VHC175F(EL) V BLK PULSE GENERATOR
+5V
2.9
IC941
NJM7912FA
-12V REG
RESET1
CX2/RX2
IC602
5V
MC74HC4538AFEL H BLK PULSE GENERATOR
+B
(2/4,3/4)
CX1/RX1
R901
0.47
1/4W
3.3
E (1/4)
D+5V
TO TA BOARD
CN13
C811 C812 C813 C814 C815 C816
C802 0.47 0.47 0.47 0.47 0.47 0.47
25V
25V
220
25V
25V
25V
25V
10V F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP
B-SS3280<AEP>-E..-P1
5
E (1/4)
(SYSTEM CONTROL,EEP ROM,H BLK/V BLK P GEN,H/V SYNC GEN)
11-37
A
B
C
D
11-37
E
F
G
H
E (2/4)
E (2/4)
E
IC501(1/2)
TL082CPS-E20
BUFFER
H LIN (3/4)
12V
HLG
HLB
5
6
7
8
9 10
IN5YB
C501
0.0068
C505
0.1
B:CHIP
OUT5
25
6
25
IN6-
OUT2
IN6+
24
IN2Y
0
23
R171
10k
:CHIP
23
R345
33k
:CHIP
7
-0.1
8
24
7
R337
10k
:CHIP
0
IN2X
IN7YA
R190
470k
:CHIP
OUT3
IN7XA
0
0.1
R175 R179
27k 100k
:CHIP :CHIP
IN7XB
IN4X
IN7YA
0.4
GND
IN7YB
17
IN4Y
VEE
16
14
VEE
0
15
17
GND
IN7YB
16
18
IN4Y
R518
27k RN:CHIP
8
2.6
0
R523
22k
:CHIP
R511
4.7k
RN:CHIP
5.1
HV OFF (1/4,3/4)
R512
68k
:CHIP
C507
0.1
25V
B:CHIP
R505
*
:RN-CP
DRV
7
IC503
FA5301BN-TE1
PWM CONTROL
ON/OFF
DT
GND
6
9
12.2(13.1)
CT
5
10
CD
4
0.7
C515
100p CH:CHIP
IS
0.4
SYNC
C SYNC
FB
CSS
2.3
VA OUT
3
19
11
3.2
C511
10
R513
10k
:CHIP
R504,505
1.5K 18K(20G1)
470 22K(14G1/14G5)
R542
820K CHIP(20G1)
750K RN-CP(14G1/14G5)
C506
0.001
CH:CHIP
1
2
3
4
5
IC531(2/2)
LM393PS-E20 DISCHARGE
+12V
C532
R531
47
120k 25V
RN:CHIP
C531
0.001
200V
R522
560
1/4W
R532
22k
RN:CHIP
2.6
C160
1
16V
F:CHIP
3
R178
10k
:CHIP
18
18
0.5
R344
10k
:CHIP 0.4
D201
MA111-TX PROTECTOR
0
12
+12V
IC502
TL431CLP-Z
R177
47k SHUNT REGURATOR
:CHIP
(2.6V)
0.1
OUT4
R190
470k
:CHIP
22
21
OUT7
2
13
R536
D533
22k
MA111-TX :CHIP
SW
C541
10
4.3
5
6
4.1
R535
10k
8 :CHIP
7
4
6.0
R548
100k
:CHIP R543
27k
RN:CHIP
R544
27k
RN:CHIP
1
R533
27k
RN:CHIP
C521
10
2
R545
100k
RN:CHIP
C533 C534
1
0.01
16V B:CHIP
R534 F:CHIP
82k
RN:CHIP
D545
MA111-TX
SW
2.0
3
1
6.0
2
HV OVP
2.0
C543
1
16V
F:CHIP
C544
0.01
B:CHIP
D534
MA111-TX SW
HV PROT(1/4)
V REF (3/4)
HV CTL (1/4)
D502
MA111-TX SW
-5V
+120V
L553
C273
0.001
R275 CH:CHIP
100k 0
:CHIP
2 -1.6
C271 R272
150p 10k
CH:CHIP :CHIP -0.1
R210
330k
:CHIP
18
3
14
DAC0
SW1
IC203(2/2)
+9V LM393PS-E20
AMP
+5V
R237
0.47
1/4W
H AGC
12
11
DAC1
IC201
CXA2026AS
SIGNAL GENERATOR
8.4 C202
1
16V
F:CHIP
R208 R222
10k
10k
:CHIP :CHIP
8
C208 4.8
10
4.7
R221 R223
10k
10k
:CHIP :CHIP
FF (3/4)
15K(3/4)
R224
10k
:CHIP
5
6
R209 R226
10k
10k
:CHIP :CHIP
C210
0.1
25V
B:CHIP
7
42.9
15
4.7
4.8
R225 R227
10k
10k
:CHIP :CHIP
R238
4.7k
1/4W
R228
10k
:CHIP
3
2
2
2.2
R239
8.2
1/4W
C232
0.1
25V
B:CHIP
VCC
-0.1
VSENCE2
-0.1
6
OUT2
5
R555
4.7k
:CHIP
4
7
8
9
R241
10k
:CHIP
C241
100p R245
B:CHIP 2.2
:CHIP
R233 R232
18k
47k
:CHIP :CHIP
R243
18k
:CHIP
R244
22k
:CHIP
NTC
R248 (1/4)
2.2k
1/4W
NTC RTN
(1/4)
C242
0.1
25V
B:CHIP
R249
100
1/4W
C301
0.1
25V
B:CHIP
R307
Q301 R303
6.8k
2M
C303
2SA1037K :CHIP
1W
10p
CH:CHIP
DFX AMP
0.7
R301
100
:CHIP 0
0
-16.3
I V.SP (1/4)
V SW (4/4)
H STAT (1/4)
R304
1.2k
:CHIP
2.8
(2.3)
R310
D301
0.47
MA111-TX 1/4W
2.1
:FPRD
BIAS
(1.6)
R306
100k
:CHIP
R302
10k
:CHIP
R242
51k
C205
0.1
25V
B:CHIP
R560
470
1/2W
C556
470p
2kV
B
R559
10
C557
0.012
2kV
D555
RGP02-20EL
+600V RECT
G2 OUT
NC
GND
TO C BOARD
CN503
1
2
DF X
DF Y
TO P BOARD
CN904
C558
0.0047
2kV
E
S
0
Q304
2SC2412K
DFX AMP
Q306
2SD2394-EF
DFX DRIVER
R309 2.8
6.8k
:CHIP (2.3)
-12V -12V RN:CHIP
R230
100
:CHIP
CN903
3P
1
2
3
L554
0.7µH
15V
+15V
R247 TP241
0.47
1/4W
R246
10
:CHIP
R234
3.9k
:CHIP
+15V-2
(1/4)
10
+12V
R231
C231 10k
R235 0.01 :CHIP
2.2 B:CHIP
:CHIP
R558
10k
+15V
38.6
(40.1)
10.1
(10.7)
:CHIP :CHIP
Q554
2SA1338-5-TB
HV BUFFER D554
MA111-TX
CLAMP
C559
1
200V
TP551
Q555
2SK2655
HV OUT SWITCHING 21
9.2
(8.9)
R556
4.7k
:CHIP
C553
0.0033
200V
FBT(H)
FBT(C)
JW(+15V)+
GND
JW(+15V)TO P BOARD
CN901
IC231
LA6510
LANDING/NTC OUT
12V
3
R236
10
:CHIP
1
14
1
0
IC203(1/2)
LM393PS-E20 5V
V SP PHASE
-VIN2
-5V
HV DRV
(3/4)
1
2
3
4
5
R554
100
1/4W
L551
L552
D553
ERC91-02TP11
FLYWHEEL
R553
22
1/4W
C555
0.1
25V
B:CHIP
9.6
(9.3)
Q552
2SC2757-T33
HV DRV AMP
-5V
R557
4.7k
:CHIP
0.7
0
3.1
(4.8)
+15V
TL082CPS-E20
BUFFER
LCC RTN
(1/4)
LCC
(1/4)
13
10
4.8
20
4 IC204(2/2)
0
56k
RN:CHIP
0.2
Q502
2SA1338-5-TB
BUFFER
Q553
2SC3392-5-TB
HV BUFFER
D552
ERB91-02TP1
PROTECTOR
38.7
(40.0)
122.0
C552
0.0047
200V
1
TP231
VSENCE1
2.1 R207
8
S
C551
100
160V
12.3
(13.1)
12.2
(13.2)
0
13
4
C562
47
160V
C561
470
10V
10k
:CHIP
124.9
(124.3)
R552
22k
:CHIP
R515
10k
:CHIP
124.9
R562 (124.3)
220k
:CHIP
PROT
(1/4) R563
7 5.3
15
8
9
SW0
C276
0.1
R561
10k
:CHIP
3
R279 R280
10k
47k
:CHIP :CHIP
25V
IC204(1/2) B:CHIP
Q273
TL082CPS-E20
2SA1037K H PARA CLAMP
BUFFER
C203
0.022 B:CHIP
IREF
0.6
7
0
C278
0.001
CH:CHIP
R284 0
10k
1.3 :CHIP 2
+VIN2
C204
0.1 25V B:CHIP
0
0
V AGC
IC202(2/2)
TL082CPS-E20
BUFFER
C277
0.1
25V
B:CHIP
VEE
7
4.1
(3.8)
GND
5
6
D271
MA111-TX
PROTECT
0
V GEN
8
16
6
PARA2
17
5.3
5.3
C275
0.001
CH:CHIP
0
6
5
R285
1M
:CHIP
R283 R282
10k
10k
:CHIP :CHIP
+VIN1
5
VCC
4.5
C274
0.1
25V
1 B:CHIP
IC202(1/2)
TL082CPS-E20
BUFFER
3.8
9V
R286 R277
100 6.8k
:CHIP :CHIP
-VIN1
H IN
19
4
PARA1
C272
0.1
25V
B:CHIP
0
OUT1
ADRS
20
3
PARA0
4.4
+9V
R271 8.9
1k
:CHIP
0.2
R281
2.2k
:CHIP
R278
1M
:CHIP
0
(-0.2)
V IN
21
2
SCL
5.2
CY(V)R
(4/4)
R211
100
:CHIP
5.3
R202
100 :CHIP
R273
R276
Q271
10k R274 180k
2SC2412K :CHIP 10k :CHIP
:CHIP
AMP
1.9
-1.5
Q561
2SA1208S-TP
HV REG OCP DET
+5V
C304
470p
CH:CHIP
R305 -16.3
1.5k
:CHIP
R308
270
:CHIP
2.6 (2.2)
R312
47
1/4W
R311
22
1/4W
1.7
:FPRD (1.3)
R313
100
:CHIP
2.1
(1.7)
11
10
9
8
C302
1
16V
F:CHIP
C321
2.2
16V
F:CHIP
T301
DFT
1
2
3
4
5
6
495
(500)
R322 149.8
2M (151.3)
1W
Q322
2SC4686A
DFY DRIVER
D322
MA111-TX
PROTECTOR
Q272
2SA1037K
CLAMP
0
(-0.2)
22
1
SDA
5V
CN902
5P
Q501
D551
Q551
2SC3392-5-TB RD12SB3-T1 PROTECTOR IRFI9630GS HV REG SWITCHING
BUFFER
-16.9
+9V
R201
100 :CHIP
4.0
5
R551
0.47
1/4W
+B
(1/4,3/4)125.2
(124.5)
9V
SCL
(1/4,3/4)
4
+15V
-5V
H PARA
(4/4)
V PARA
(4/4)
2H TIM
(1/4,3/4,4/4)
SDA
(1/4,3/4)
(1/4)
IK PROT (1/4)
-5V
D TIM
(1/4,3/4)
FOR CHECK
CN501
5P
R547
22k
:CHIP
D544 R546
MA111-TX 10k
SW
:CHIP
C542
47
25V
R542
*
GND
HV ADJ
IK PROT
ABL CUT
HV RTN
ABL1 (1/4)
20
20
IN3+
C510
220p
CH:CHIP
R191 C161
10k 1000p
:CHIP CH:CHIP
19
IN4X
0
C172
5p
CH:CHIP
18
R172
10k
:CHIP
-0.1
IN7XB
C509
0.1
25V R504
B:CHIP *
:RN-CP
14
12V
0
C171
5p
CH:CHIP
0.6
OUT4
R176 R174
10k
47k
:CHIP :CHIP
-0.1
10
IN7XA
OUT6
11
11
OUT3
0.3
0
IN3-
12
OUT7
21
10
IN3+
R173
22k
:CHIP
C333
5p
CH:CHIP
13
OUT6
9
0
22
9
IN3-
0
17
R336
33k
:CHIP
VCC
30
29
28
28
5
OUTB
R503
22k
RN:CHIP
D501 (-0.3)
RD12SB3-T1
PROTECTOR
R508
10k
:CHIP
-0.1
R343
47k
:CHIP
C201
10
IN6+
R335
33k
:CHIP
-1.1
R501
100k
:CHIP
C502
0.001
CH:CHIP
1
7 RN:CHIP
HV RTN(AC)(1/4)
19
R342
47k
:CHIP
R229 R203
100k 10k
:CHIP :CHIP
IN6-
OUT2
12
R333
10k
:CHIP
0.2
IN2Y
13
R204
R205 2.2k
10k :CHIP
:CHIP
3
IN5YA
0.6
0.5
+5V
R206
10k
:CHIP
OUTA
0
C332
5p
CH:CHIP
5V
OUT5
16
8
R340 -0.1
10k
:CHIP
R334
10k
:CHIP
R341
100k
:CHIP
Q201
2SA1037K
AMP
IN2X
-0.2
R339
47k
:CHIP
R332
47k
:CHIP
+5V
0.8
R347
47k
:CHIP
26
5
6
R338
47k
:CHIP
4.3
1.5
1.7
2.7
3.6
4.0
2.6
3.0
V BLK T
(1/4)
H BLK W
(1/4)
H BLK PH
(1/4)
IN5YB
IN5XB
-0.5
14
3
OUTB
15
HBW
2
IN5YA
0.4
5V
1
27
-1.3
OUTA
IN1
18k
-1.1 6
(-0.3)
5
HV RTN(DC)(1/4)
15
R517
6.8k
:CHIP
1.1
D542
MA111-TX
BIAS
D543
MA111-TX
DISCHARGE
DFCOR
VBT
2
R346
47k
:CHIP
HMP
LDBK
DFSID
4
HCB
DI
CLK
HBP
DFTB
IC205
MB88346BPFV-EE
D/A CONVERTER
VBP
VBB
20 19 18 17 16 15 14 13 12 11
IN5XA
16
R514
100k
:CHIP
R516 C512
27k
22
:CHIP
C514
1
16V
F:CHIP 2.1
IC531(1/2)
LM393PS-E20
DISCHAGE
R331
10k
:CHIP 0
SW1
R520
10k
:CHIP
C516
1
16V
F:CHIP
C519
0.1
25V
B:CHIP
C517
47
25V
IC501(2/2)
TL082CPS-E20
BUFFER
R502
27
IN5XB
SW2
26
IN1
0
4
0.7
4.0
2.3
3.0
0
5.3
0
D+5V
29
C331
0.1
25V
B:CHIP
5V-2
VCC
0.3
0.4
-12V
ABL (1/4)
1
IN5XA
0.3
R521
470
1/4W
2.6 5.3
4
IN(+) VREF
2
C513
0.0022
CH:CHIP
R519
10k
:CHIP
+15V
7.3
1 (8.0)
9.3
8
+12V
2
2
SW1
5V
4
SW2
IC151
CXA1726AM-T6
H LIN CONV
30
1
VCC
3
IC301
5V CXA1726AM-T6 DF MOD
3
DF BLK P
(1/4)
LD BLK
(1/4,4/4)
L SCLK
(1/4,4/4)
L MOSI
(1/4,4/4)
V BLK P
(1/4)
V BLK B
(1/4)
7.3
(8.0)
C571
0.001
CH:CHIP
C572
0.1
25V
B:CHIP
15V
+12V
3
ABL2(1/4)
IN(-)
R572
100k
:CHIP
R571
100k
:CHIP
D531
MA111-TX
BIAS
D532
MA111-TX
DISCHARGE
1
(2/4)
SIGNAL GEN.,PWM CONTROL,HV REG/HV OUT SWITCHING
DYNAMIC FOCUS,LANDING/NTC OUT,H LIN.CONV.,D/A CONV.
R321
33k
:CHIP
147.2 (151.3)
R324
10k
1/2W
R323
10M
1W
0.6
CN905
2P
22
Q321
2SC4686A
DFY AMP
-15V
Q302
2SA1037K
-15V DFX AMP
Q303
2SC2412K
DFX AMP
Q307
2SB1565EF
DFX DRIVER
D321
MA111-TX
PROTECTOR
B-SS3280<AEP>-E..-P2
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
11-38
A
B
C
D
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
11-38
E
F
G
H
E (3/4)
E (3/4)
D TIM (1/4,2/4)
HV DRV (2/4)
1
38
12
GND
GND
+5V
15
SCL
4.4
(4.8)
VP FIL
C015
0.0047
B:CHIP
32
9.3
ABL
ABL
FIL0
31
9.3
V PARA
C016
1
16V
F:CHIP
R014
180k
:CHIP
3.3
R013
82k
:CHIP
VS FIL
C014
4.1 0.0047
29
3.7
VS
G
25
28
21
3.7
V PROT
B
EXTCR
D/A
0 3
2
B:CHIP
R011
4.7k
9.5 :CHIP
R055
* 3W
C054
0.047
200V
1.8
R050 R051 R052
1k
470
10k
:CHIP :CHIP :CHIP
3
2
1
R053
3.3k
1/4W
0
5V
+5V
R029
10k
RN:CHIP
Q112
2SA1037K
AFC P OUT
+9V
4.4
2.8
R115
4.7k
:CHIP
I AFC P(1/4)
H P
(1/4)
H +B
(1/4)
I V SAW(1/4)
V STOP (1/4)
H STOP (1/4)
5.3
D121
MA111-TX
SW
0
C122
0.1
25V
B:CHIP
D131
MA111-TX
SW
5.3
4.9
D113
MA111-TX
PROTECTOR
R113
1k
:CHIP
43.9
(52.6)
35.6
(42.5)
12
10
R064
10
2W
8
9
V.DY
5
V.DY.RET
13
H.DY
4
DY
H.DY.RET
26.9
(31.9)
35.6
(42.5)
14
C101
100
25V
C102
100
25V
2
CN007
6P
R102
1
1/4W
D102
V19E-T52 -RECT
1
2
3
4
5
6
L064
*
:HLC
R065
220
1/4W
:FUSE
H.DY
H.DY
H.DY.RET
H.DY.RET
V.DY.RET
V.DY
C064
0.0015
500V
B
CY
CY
CV
CV
HP
HP
HP
HP
+ (4/4)
- (4/4)
+ (4/4)
- (4/4)
30
FB051
0UH
C055
680p
2kV
B
0
6
C058
680p
2kV
B
C056 C057
470p 0.012
2kV 2kV
B
8
C065
*
200V
C065,C066
2.2 2.2(20G1)
3.3 3.9(14G1/14G5)
C066
*
200V
3
1
7
6
R162
Q156
100
1W 2SC2362KG-AA
3
R111
1k
:CHIP
-0.4
Q111
2SA1037K
AFC PULSE AMP
C111
*
100V
R117 R116
470k 47k
:CHIP :CHIP
-12V
R154
6.8k
:CHIP
Q151
2SA1037K 0.7
H LIN AMP
C111
0.047(20G1)
0.033(14G1/14G5)
D111
RD4.3SB3-T1
DAMPER
-12V
+15V
R040
470k
:CHIP
1
3
4
5
6
C151
0.1
25V
B:CHIP
Q157
2SC4159-E
H LIN OUT
TP151
0.7
0.1
D151
MA111-TX
PROTECTOR
R160
2.2k
1W
R161
2.2
1W
D152
MA111-TX
PROTECTOR
0.1
-0.3
-16.9
R153
560
:CHIP
7
C156
0.001
200V
R157
0.47
1/4W
R159
0.47
1/4W
:FUSE
33
0.1
R151 R152
100
10k
:CHIP :CHIP
0
+IN
V BOOST
0.2
OUT
-17.5
VEE
-16.7
BOOST
VCC
2
16.5
(16.1)
R032
0.47
1/4W
16.6
(16.4)
R031
0.47
1/4W
C131
1
16V
F:CHIP
Q152
2SA1037K
CLAMP
0.1
IC031
STV9379
V OUT
R156
1k 16.9
1W
R163
0.47
:FPRD
4
T151
HLT
H LIN AMP
15V
C036
0.01
B:CHIP
31
0.3
0
Q131
2SA1037K
V PROT STOP
R131
1k
:CHIP
-15V
Q115
PSC3209LK-TP
H LIN AMP
R158
0.47
1/4W
4
Q159
2SA1606-E
H LIN OUT
-17.5
R155
10
:CHIP
-15V
C031
470
25V
0.3
Q132
DTC144EKA-T146
INVERTER
HV OFF(1/4,2/4)
Q121
DTC144EKA-T146
H PROT STOP
1.0
R133
10k
:CHIP
C132
2.2
16V
F:CHIP
-0.3
C121
470p
500V
B
3
+12V
R112
C112
4.7k
0.1 25V B:CHIP :CHIP
-IN
R134
270k
:CHIP
0.1
R100
1
1/4W
12V
+15V
Q133
DTC144EKA-T146
V STOP OUT
15
11
15V -15V
R122
270k
:CHIP
C105
1
16V
F:CHIP
5
C113
D112
470p
MA111-TX CH:CHIP
PROTECTOR
R114
47k
:CHIP
Q122
DTC144EKA-T146
H STOP OUT
R101
1
1/4W
2
7
4
C053
330p
500V
B
C052
100p
CH:CHIP
16
6
Q054
36.0TP052
2SC4927-01(43.0)
H OUT
T051
HDT
1
L063
220µH
L051
0.7µH
Q053
2SC2688-L H DRIVE
R103
1
2W
D103
RD5.6SB-T1
H CENTER REF
OUT
ON/OFF
D.T
GND
C.T
C.D
0
0.2
C.SY
Q061
IRFI9630GS-LF
PWM
C104
0.1
B:CHIP
R108 R109
10
2.2k
:FPRD :CHIP
L066
220µH
122.6
(121.3)
R062
22
1/4W
L101
D154
D153
HSM83-TL SW HSM83-TL SW
25
24
IK
L062
5mH
5
D101
V19E-T52
+RECT
1
0
R028
2.2k
RN:CHIP
26
23
2.6
C051
0.1
25V
2.7B:CHIP
Q051
2SC2412K
H DRIVE
BUFFER
IC091(2/2)
NJM4558M-TE2
VS AMP
R026
1k
:CHIP
27
22
3.5
C063
100
160V
C087
0.022
200V
36.4
(43.7)
4
+15V
D062
ERC91-02TP11
DAMPER
R012
100 :CHIP
R030 2.2M :CHIP
30
3.7
R
125.1
(124.4)
C061 R063
33
22k
160V :CHIP
R054
15V R054,R055
* 3W
1K (20G1)
2.2K(14G1/14G5)
6.5
33
20
C013
0.1
25V
B:CHIP
COMP
SDA
CH:CHIP
4.2
19
R010
100
:CHIP
5.3
2.7
L061
100µH
D122
RD4.3SB3-T1
+B PROT
C018
0.33
16V
B:CHIP
C017
0.2 0.001
D TIM
C086
0.022
200V
D061
RD12SB3-T1
PROTECTOR
3
T052
HOT
R074
3K (20G1)
3.3K(14G1/14G5)
5.3
R076
10k
:CHIP
R127
10k
C062
:CHIP 0.0047
200V
4.4
(4.8)
18
C012
0.1
25V
B:CHIP
R009
2.2k
:CHIP
17
R008
39k
:CHIP
CLK
5.3
34
16
R007
68k
:CHIP
R025
10k
:CHIP
C008
0.1
25V
B:CHIP
C009
0.1
25V
B:CHIP
C010
0.1
25V
B:CHIP
C011
0.1
25V
B:CHIP
2.2
35
P ABL
R006
100
:CHIP
SCL (1/4,2/4)
SDA (1/4,2/4)
36
14
R005
100
:CHIP
8
C074
10
R074
*
:RN-CP
R126
270k
:CHIP
R016
33k
:CHIP
+9V
0
7
IC101
LA6500-FA
H CENTER AMP
C103
0.01
CH:CHIP
R105
1.5k
:CHIP
+120V
37
13
R004
3.3M
:CHIP
VCC
VCC
6
2
R107 R106
22k
22k
:CHIP :CHIP
-12V
R086
R087
R088
R089
10k
10k
10k
10k
RN:CHIP RN:CHIP RN:CHIP RN:CHIP
C083
1
16V (1/4,2/4)
F:CHIP +B R061
0.47
1/4W
+9V
C006
0.33
16V
B:CHIP
C073
0.001
CH:CHIP
27
0.6
9V
5
Q072
2SA1338-5-TB
PWM DRIVE
R104
4.7k
:CHIP
R095
10k
:CHIP
-12V
11.9
(10.8)
1
1.3
39
11
VSS
R017
2.7k
:CHIP
4
9
S
VDD
V TIM
2.8 2.8
(3.1)(3.1)
R084
470k C072 R075
:CHIP 0.1
27k
25V :CHIP
B:CHIP
3.3 5V
10
24
V TIM
(1/4)
R071
5.6k
RN:CHIP
C019
0.1
25V
B:CHIP
40
9
HD
2H TIM
C141
0.1
25V
B:CHIP
R072
10k
RN:CHIP
26
1.9
C020
0.001
CH:CHIP
2.4
41
8
HP
23
2H TIM
(1/4,2/4,4/4)
6.4
3
29
1.1
10
43.2
2.6
-16.9
L2FIL
2
2.1
11
C091
0.1
25V
B:CHIP
11.7
(10.7)
10
9
8
7
6
C005
0.1
25V
B:CHIP
42
R024
1k
:CHIP
7
R003
10k
:CHIP
1
12
R077
10k
:CHIP
7
4
5
H SYNC(1/4)
IC071
FA5301BN-TE1
PWM CONTROL
0.7
13
5
2.6 6
Q071
2SC3392-5-TB
PWM DRIVE
1
2
6
XRAY
HS
R019
470
0 :CHIP
43
2.8
X001
R142
47k
:CHIP
14
+12V
Q091
2SC2362KG-AA
IC091(1/2) H CENTER BIAS
NJM4558M-TE2
H CENTER AMP 8
R091
10k
:CHIP
15V
15V
R079
6.8k
:CHIP
53.5(71.7)
R023
1k
:CHIP
CERA
VS
+5V
44
5
V SYNC(1/4)
5V
*
3.4
5.3
16
15
I.S
4.8
(5.0)
C080
47
25V
28
SYNC
45
4
AFCFIL1
VSS
C022
0.47
C021
0.0022
CH:CHIP
C077
1
16V
F:CHIP
F.B
46
3
C004
0.1
25V
B:CHIP
R002
10k
:CHIP
R020
10k
:CHIP
C082
1
16V
F:CHIP
C.S.O
ER.OUT
4.8
(5.0)
AFCFIL3
R083
470
1/4W
2.8
(3.1)
CH:CHIP
47
2
AFCFIL2
R080 R078 C075
27k
10
27k
:RN-CP :CHIP
C079 R082
47
10k
25V :CHIP
15V
C081
0.01
B:CHIP
13.3
0.2
4.8 C023
(5.0) 0.001
15V
+9V
IN(+) REF
HFREQ
IREF
R022 R021
10k
10k
:CHIP :CHIP
C078
100p
CH:CHIP
IN(-) VCC
48
1
R001
8.2k 4.0
RN:CHIP
12V
9V
IC001
CXA1840S
SIGNAL GENERATOR
C001
0.1
25V
B:CHIP
V REF (2/4)
C076
0.0022
CH:CHIP
29.8
R081
1k
:CHIP
35.6
(42.5)
FF (2/4)
15K (2/4)
C032
470
25V
C024
0.01
B:CHIP
R132
47k
:CHIP
-12V
R033
20k
:RN-CP
C123
470p
500V
B
R036
3.3k
:CHIP
C033
100
R034
5.6k
RN:CHIP
D031
GP08DPKG23
PROTECTOR
R035
*
2W
R037
1.5
1/4W
-15V
R038
820
1W
TP031
C034
0.1
100V
R035
2.7(20G1)
4.7(14G1)
32
H LIN(2/4)
E
V SAW (1/4)
SIGNAL GENERATOR,PWM CONTROL
(3/4) H/V OUT,H LIN AMP
5
B-SS3280<AEP>-E..-P3
11-39
A
B
C
D
11-39
E
F
G
H
E (4/4)
(BVM-20G1 ONLY)
1
E
(4/4)
SIGNAL GENERATOR
D/A C,CYH/CYV OUT
ROT OUT
5V
(0)
LD CV(1/4)
L SCLK(1/4,2/4)
L MOSI(1/4,2/4)
3
4
5
LDCV
6
7
8
9 10
(2.7)
2
(5.3)
R751
R749
R750 100k R748 100k
51k :CHIP 51k :CHIP
:RN-CP
:CHIP
2
-5V
35
(0)
10
18
17
GND
13
(0)
R741 R743
51k
22k
:RN-CP :CHIP
3
14
15
R742
22k
:CHIP
R747
100k
:CHIP
2H TIM
(1/4,2/4,3/4)
H PARA
(2/4)
IC701
CXA1726AM-T6
SIGNAL GENERATOR
36
IN4Y
12
(0)
11
16
VEE
9
19
IN7YB
8
(0)
OUT7
IN3+
7
20
(0.5)
(-0.5)
OUT3
IN7XA
(1.7)
(-0.1)
OUT4
IN7XB
(0.9)
(0.3)
IN4X
IN7YA
(0)
IN3-
OUT6
OUT2
6
(-0.2)
IN2Y
5
(0.2)
OUT5
21
IN2X
22
4
(0.3)
34
3
23
IN5YB
IN5XB
2
IN1
1
24
OUTB
IN5XA
(0)
(0.6)
25
IN5YA
26
OUTA
27
(0.6)
28
SW1
29
VCC
30
(0.3)
5V
R746
22k
:CHIP
SW2
37
0.4
V SW(2/4)
R744
22k
:CHIP
IN6+
R754
100k
:CHIP
C742 R752
100k
5p
CH:CHIP :CHIP
IN6-
R756
100k
:CHIP
R745
51k
:RN-CP
(0.4)
R753
51k
:RN-CP
(2.7)
R755
51k
:RN-CP
(1.9)
V PARA(2/4)
-5V
(-0.5)
1
IC703
MB88346BPFV-EF
D/A CONVERTER
RCC
(3.3)
RB
RT
(3.7)(2.7)
LC
RC
(2.7) (0)
LT
DI
(5.3)
LB
CLK
(4.0)
20 19 18 17 16 15 14 13 12 11
C741
5p
CH:CHIP
-5V
-5V
Q726
2SC2362KG-AA
CY HP AMP
6V
CY(H)RTN(1/4)
CV HP - (3/4)
CV HP + (3/4)
CY(H)(1/4)
+6V
Q721
2SA1037K-QR
CY HP AMP
C724
0.001
200V
R727
1k
1W
(6.8)
Q727
2SC4159-E
CY HP OUT
(0.8)
R721
10k
:CHIP
R722
10k
:CHIP
(-0.1)
(-0.2)
R728
0.47 TP721
1/4W
(-0.1)
C721
220p
CH:CHIP
4
D721
MA111-TX
PROTECTOR (0.4)
R732
Q722
22k
2SA1037K-QR
1W
CLAMP
R725
2.2k
:CHIP (0.6)
R733
1
1W
C725
100p
CH:CHIP
R729
0.47
1/4W
D722
MA111-TX
PROTECTOR
(-6.3)
(-0.2)
Q729
2SA1606-E
CY HP OUT
(-0.6)
(-6.3)
R724
560
:CHIP
Q725
2SC2958-TL
CY HP AMP
CY HP - (3/4)
CY HP + (3/4)
R731
0.47
1/4W
(-6.9)
R726
10
:CHIP
-6V
-6V
VCC
(-0.1)
VSENCE2
(-0.1)
OUT2
(0)
6
-VIN2
+VIN2
5
(0)
VEE
(0)
+VIN1
(0)
-VIN1
(0)
OUT1
(0)
VSENCE1
ROT RTN (1/4)
ROT (1/4)
IC702
LA6510
ROT/CY(V)OUT
12V
R707
0.47
1/4W
TP701
R708
4.7k
1/4W
5
R709
10
1/4W
1
2
3
4
7
8
10
+12V
C701
R705 0.01
2.2 B:CHIP
:CHIP
R701
10k
:CHIP
C711
R711 0.001 R715
10k :CHIP 2.2
:CHIP
:CHIP
R706
10
:CHIP
C702
0.1
25V
B:CHIP
9
R717 TP711
0.47
1/4W
CY(V)(1/4)
R716
10
:CHIP
R704
4.7k
:CHIP
R703 R702 R712 R713
10k
47k
51k
18k
:CHIP :CHIP :RN-CP :CHIP
R714
47k
:CHIP
38
C712
0.1
25V
B:CHIP
R718
330
1/4W
CY(V)RTN (1/4)
R719
15
1/4W
-12V -12V
(2/4) CY(V)R
B-SS3280<AEP>-E..-P4
11-40
A
B
C
D
11-40
E
F
G
H
E
E
E Board IC Block Diagrams
5.2Vp-p (H)
4.4Vp-p (H)
4.3Vp-p (V)
696Vp-p (H)
412Vp-p (H)
OUT b 5
4Vp-p (H)
L
5
6
#™ (14 INCH)
#™ (20 INCH)
#£ (14 INCH)
VDD
VSS2
JGND
JVCC
CLK
D-TIM
COMP-IN
VP-FIL
V-PARA
VS-FIL
VS-OUT
V PROT
R-OUT
G-OUT
B-OUT
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
27 IN5 Ya
GND
HD
H
LOOP2
D/A
V-OUT
P-OUT
1BIT-DAC
26 IN5 Yb
OUT
CLAMP
DEF-DSP
25 OUT5
IN2 X 6
4
48
28 IN5 Xb
VDD
MUL
L
H
L
H
OUT a 4
29 IN5 Xa
VCC
H
IN1 3
30 SW2
HD-OUT
L
HP-IN
VCC 1
SW1 2
L2FIL
#¡
X-RAY
#º (20 INCH)
CERA
#º (14 INCH)
AFCFIL1
3
CXA1840S (IC001)
AFCFIL3
2
CXA1726AM (IC151, 301, 701)
AFCFIL2
1
E Board Waveforms (2/2)
H-FREQ
E Board Waveforms (1/2)
MUL
IN2 Y 7
24 IN6–
OUT2 8
23 IN6+
IN3– 9
22 OUT6
HSEP
A/D
H-AFC
DRIVE
GAMMA
CLOCK
19 IN7 Yb
L
18 IN7 Ya
H
SW1
13
12
13
14
15
16
17
18
19
20
21
22
23
24
IK-IN
SW0
14
11
D/A
10
EXT CR
9
B-IN
8
G-IN
7
R-IN
6
ABL-FIL
5
ABL-IN
4
SDA
3
SVCC
#•
2
SGND
#¶
#§
1
VTIM
2.1Vp-p (H)
SSCP
!™
3.3Vp-p (H)
2HTIM
!¡
121Vp-p (H)
VCC
16 VEE
HTIM
!º
2.5Vp-p (V)
CXA2026AS (IC201)
5Vp-p (V)
!£
5Vp-p (H)
!¢
5.9Vp-p (8MHz)
3.3Vp-p (H)
5.1Vp-p (V)
V IN
21
1.7Vp-p (V)
VGEN
17
VAGC
16
H IN
19
H SAW
18
HAGC
12
IREF
15
HPARA
22
H.TILT
!∞
IREF
ST0
SW
ST1
COMP
TILE OFF
SW0
H SAW
SW1
FF
COMP
PWM
2Vp-p (V)
!§
5Vp-p (H)
!¶
5Vp-p (V)
COMP
!•
HPARA
U.YBOW U.CBOW U.MBH
VPARA
1.3Vp-p (V)
!ª
1.7Vp-p (H)
@º
H.TILT
1.1Vp-p (V)
U.TILT
U.PARA
X2
H.DUTY
@¡
L.TILT
L.PARA
X2
V SAW
DAC0
L.YBOW L.CBOW L.MBH
15.5Vp-p (H)
@™ (14 INCH)
1.1Vp-p (V)
@™ (20 INCH)
502Vp-p (H)
BUS
DECODER
@£
20
1
ADRS SDA
300Vp-p (V)
@¢
330Vp-p (V)
@∞
3Vp-p (2H)
H.AMP
DAC1
DC.SHIFT
PARA
X2
DAC
2
3
4
5
6
7
SCL
PARA0
PARA1
VCC
PARA2
GND
9
8
10
PWM H TILT DAC0
FA5301BN-TE1 (IC071, 503)
@§
11
DAC1
LA6500FA (IC101)
ER AMP
IN(-)
1
IN(+)
2
15 REF
ER OUT
3
14 CSO
BIAS
VREF
16 VCC
1
+
3.7Vp-p (V)
4Vp-p (V)
4.8Vp-p (H)
PWM
@¶
@•
@ª
FLIP.FLOP
FB
4
Q
OSC
5
1.7Vp-p (H)
15.2Vp-p (H)
CO
6
GND
7
ON/OFF
8
LO
11-41
11 CT
25V
10 Dr
9
ON/OFF
11-41
12 CSY
S
0.5V
1.5Vp-p (V)
13 SYNC
R
O.C.P
IS
AMP
CLAMP
S-BRT
ABL
17 IN7 Yb
GND 15
5Vp-p (V)
LATCH
D/A
SCL
IN4 Y 14
PABL
IN4 X 13
BUS
DEC
IREF
HS-OUT
#∞
MUL
MUL
5Vp-p (H)
COUNT-PROC
PULSE-INTERFACE
H
OUT4 12
HS-IN
#¢
83.2Vp-p (H)
VS-IN
#£ (20 INCH)
57.5Vp-p (V)
VSS1
9
56.5Vp-p (V)
V-FIL
8
5Vp-p (V)
IREF
7
7.2Vp-p (V)
20 IN7 Xa
50/60
5.1Vp-p (H)
L
AKB
D/A
VSEP
21 OUT7
IN3+ 10
OUT3 11
OFF
OUT
2
–
3
VEE
4
OUT
5
VCC
E
LA6510 (IC231, 702)
VOUT1 2
MC74HC4053F (IC625)
+VIN1
VCC
+VIN2
4
10
6
CURRENT
CONTROLLED
CIRCUIT
VSENCE1 1
CURRENT
CONTROLLED
CIRCUIT
X1
1
16 VDD
X0
2
15 XC
Y1
3
14 ZC
YC
4
13 Z1
Y0
5
OPEN
X25040SI (IC803)
CS 1
STATUS
REGISTER
WRITE
PROTECT
LOGIC
X DECODE
LOGIC
512 BYTE
ARRAY
8
VDD
7
HOLD
6
SCK
5
SI
32
SO 2
32X32
COMMNAD
DECODE
AND
CONTROL
LOGIC
32
32X32
12 Z0
8 VOUT2
9 VSENCE2
E
OPEN
EN
6
11 AZ
VEE
7
10 AX
8
9
GND
WP 3
AY
WRITE
CONTROL
AND
TIMING
LOGIC
64
64X32
OPEN
GND 4
4
3
5
7
Y DECODE
-VIN1 VEE -VIN2
DATA REGISTER
MC74HC4538AF (IC602, 623)
MB88346BPFV (IC205, 703)
VDD
2-C
2-CR
2-RD
2-CK
2-CR
2-Q
2-Q
16
15
14
13
12
11
10
9
12 BIT SHIFT REGISTER
D0
D1 D2
D3 D4
D5 D6
D7 D8
D9 D10 D11
VSS 1
ADDRESS
DECODER
A03 2
8
12
1 2 3 4
12
D0
D7
A04 3
D0
A05 4
D7
20
GND
19
A02
18
A01
17
DI
16
CLK
15
LD
A08 7
14
DO
A09 8
13
A12
A10 9
12
A11
11
VCC
A06
A07
1
8 BIT
LATCH
8 BIT
LATCH
8 BIT
R-2R
D/A CONVERTER
8 BIT
R-2R
D/A CONVERTER
5
6
VDD 10
1
2
3
4
5
6
7
8
1-C
1-CR
1-RD
1-CK
1-CK
1-Q
1-Q
GND
STV9379 (IC031)
A12
A01
MB89613R-438 (IC802)
13
12
Q
CLR
59 PTO
Q
CK D
MOD0 21
MOD1 22
EXTERNAL
BUS
INTERFACE
Q
Q
CLR
D CK
2
3
4
5
6
7
8
2Q
2Q
GND
Q
1
2D
CK
CLR
Q
1D
D
1Q
D
Q
51 ADST
3 SI2
2 SO2
1 SCK2
PORT 4
PORT 2
9
CMOS I/O PORT
8 BIT
SERIAL 2
CMOS OUT PORT
CK
CLR
Q
10
1Q
54 SI1
53 SO1
52 SCK1
8 BIT
SERIAL 1
A15 34
ALE 26
RD 27
WR 28
CLK 29
RDY 30
HRQ 31
HAK 32
BUFC 33
55 EC
11
CLEAR
A08 41
16 BIT
TIMER COUNT
CMOS I/O PORT
INTERNAL BUS
AD7 42
8
PORT 0/1
AD0 49
58 WTO
56 PWC
BUZZER OUT
64
60
61
62
63
BZ
P40
P41
P42
P43
N-CH OPEN DRAIN I/O PORT
4 P50
RAM
(256 X 8bit)
CPU
N-CH OPEN DRAIN I/O PORT
EXTERNAL
INTERRUPT
INPUT PORT
ROM
(8K X 8bit)
PORT 6
RST 20
8 BIT PULSE
WIDTH COUNT
TIMER
PORT 3
RESET
(WDT)
3Q
14
CLOCK
15
3Q
4D
16
3D
CLOCK CONTROL
8 BIT
PWM TIMER
4Q
TIME BASE
TIMER
4Q
OSC
(MAX 10MHz)
VCC
TC74VHC175F (IC613)
X0 23
X1 24
8
11 P57
15
16
17
18
INTO
INT1
INT2
INT3
19 P64
11-42
11-42
C
G1
G2
G4
GM RCV
V901
20MT3(20G1U)
20MT1(20GE)
20MT1(S)(20G1A)
14MT3(14G1U/14G5U)
14MT1(14G1A/14G1E/14G5A/14G5E)
V901
PICTURE
TUBE
H1
H2
C
C Board IC Block Diagram
V901
20MT1(20G1J)
14MT1(14G1J/14G5J)
1
TDA6101Q/N3 (IC701)
CURRENT
SOURCE
MIRROR
MIRROR
HV
KR KG
TO P BOARD T901(F.B.T)
KB
V bias
DIFFERENIAL
STAGE
+
–
FOLLOWER
MIRROR
MIRROR
6.3
12.7
6.1
120V
R702
15k
:RN-CP
CN507
3P
WHT
:S-MICRO
0
124.6
91.0
91.8
89.7
C703
10
160V
:HT
1
2
3
4
5
6
7
8
C(R.G.B OUT)
C704
0.01
200V
:PT
IC701
TDA6101Q/N3
BLANKING AMP
1
2
R509
1M
1/2W
:RC
R707
470k
C701
0.01
B:CHIP
R705
39k
1/2W
:RN
R704
12k
:RN-CP
C702
4.7
160V
:HT
1
R708
100
1/2W
:RC
R501
470
1/2W
:RC
R503
470
1/2W
:RC
Q603
2SC4686A
H STAT OUT
R611
10k
:CHIP
D604
MA111-TX
PROTECTOR 3.6 4.2
H.STAT
C506
0.0047
2kV
E
RV501
110M
R513
220
1/2W
:RC
1
KR
2
NC
3
NC
4
GND
TO BK BOARD(4/9)
CN2
R
L502
2.2µH
R507
30M
1W
:RN
SG506
R613
390k
:CHIP
5
6
7
9.5
4
R609
10k
4.5:CHIP
IC601(2/2)
LM358PS-E20
H STAT CONTROL
R612
10k
:CHIP
Q602
2SC4686A
G2 BUFFER
B
C505
0.0047
2kV
E
CN505
4P
WHT
:S-MICRO
SG507
D603
MA111-TX
PROTECTOR
R508
10M
1/2W
:RC
SG504
2
G
1
KG
2
NC
3
NC
4
GND
TO BK BOARD(5/9)
CN3
SG501 C504
0.0047
2kV
E
L501
2.2µH
R511
100
1/2W
:RC
B
Be sure to connect the
connector CN501 for safety
D602
MA111-TX
PROTECTOR
215
9.9
R606
10k
:CHIP
1
R608
10M
1W
:RN
4.2
1
2
3
+600V
NC
GND
R615
22k
:CHIP
R605
100k
:CHIP
3
CN503
3P
D601
MA111-TX
DISCHARGE
R601
180k
:CHIP
TO E BOARD
CN903
3.6
3
3.6
2
IC601(1/2)
LM358PS-E20
G2 CONTROL
R604
4.7k
:CHIP
1
2
3
4
5
6
7
8
600V
10.4
R514
220
1/2W
:RC
CN506
4P
BLK
:S-MICRO
1
KB
2
NC
3
NC
4
GND
TO BK BOARD(6/9)
CN4
R607
10M
1W
:RN
R516
220k
1/2W
:RC
SG505
SG502
Q601
2SC4686A
G2 AMP
215
G
R505
1k
1/2W
:RC
9
VOF
2
TO TA BOARD
CN16
H.STAT CTRL
G2 CTRL
GND
-12V
+12V
GND
H1
H2
4.5
+12V
GM G1-1
2
4 H1
5 H2
6
RCV 13
7 G1-2
12
8 KB
KR
1
11 10 9
G2
G1-3
3
KG
1
SG503
R510
100
1/2W
:RC
8
VOC
CN508
8P
WHT
:S-MICRO
G4
CN504
4P
RED
:S-MICRO
7
VCN
C508
47
25V
R610
180k
:CHIP
8
J501
CRT SOCKET
R504
1k
1/2W
:RC
6
VDDH
CHASSIS GND
-12V
R614
1M
1/2W
:RC
SG508
FV1
5
IOM
GND
C507
47
25V
D501
EGP10GPKG23
BLANKING CLAMP
113.8
TO P BOARD
T901(F.B.T)
FV2
4
GND
GND
GND
CN502
:TAB
+12V
R502
470
1/2W
:RC
3
VIN
CHASSIS GND
R706
1k
:CHIP
G1
1
R703
GND
2
15k
:RN-CP
+120V
3
C705
D701
TO BK BOARD(7/9)
47
RD15SB-T1 25V
CN5
PROTECTOR
2
VDDL
9
120V
R701
1.5k
:RN-CP
1
VIP
CN501
2P
WHT
:MINI
C602
0.01
B:CHIP
R602
100k
:CHIP
C601
220
16V
R603
68k
:CHIP
4
R506
1k
1/2W
:RC
B-SS3280<AEP>-C..
L503
2.2µH
R515
220
1/2W
:RC
R512
100
1/2W
:RC
C Board Waveforms
1
2
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
3
5
74Vp-p (H)
75.6Vp-p (H)
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
67.6Vp-p (H)
11-43
A
B
C
D
11-43
E
F
G
H
P
1
CN901
5P
WHT
:MINI
FBT(H)
FBT(C)
JW(15V)
GND
JW(+15V)
TO E BOARD
CN902
R908
4.7k
1
1
2
3
4
5
HV
1
+15V
14
15
NL902
2
13
CN902
11P
WHT
:S-MICRO
6
R909
C903 220k
0.022
2
HV RTN(AC) 1
+15V(JW) 2
+15V(JW) 3
4
ABL
5
IK PROT
+15V(JW) 6
+15V(JW) 7
8
GND
9
HV PROT
10
GND
HV RTN(DC) 11
TO TA BOARD
CN15
TO C BOARD
CRT SOCKET(G4)
1
FV1
FV1
5
17
1
2
+15V
18
7
16
D901
RGP10GPKG23
3
R907
0.47
:FPRD
R903,R906
1.5K 1.5K(20G1)
1.8K 1.8K(14G1/14G5)
1
4
8
NL901
R901
4.7k
:RN
R904
4.7k
:RN
R902
4.7k
:RN
R905
4.7k
:RN
11
+15V
10
12
+15V
R903
*
:RN
TO E BOARD
CN905
DF X
DF Y
CN904
2P
WHT
:MINI
FV2
9
CN903
4P
WHT
:MINI
HV
TO PICTURE TUBE
R906
*
:RN
C901
0.01
100V
:PT
FV2
TO C BOARD
CRT SOCKET(GM)
C902
0.01
100V
:PT
T901
NX-4141
3
IK IN
IK OUT
JW(+15V)
JW(+15V)
1
2
3
4
P
(F.B.T)
B-SS3280<AEP>-P..
4
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
5
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
11-44
A
B
C
D
E
F
G
H
YA, YB, YC, HD
TO TB BOARD
CN6(1,2pin)
+12V
TALLY
R101 R102 R103 R104 R105 R106 R107 R108 R109 R110
3.3k 3.3k 3.3k 3.3k 3.3k 3.3k 3.3k 3.3k 3.3k 3.3k
:CHIP:CHIP :CHIP:CHIP:CHIP:CHIP:CHIP :CHIP:CHIP :CHIP
2
1
1
+12V
CN101
2P
WHT
:S-MICRO
D101
D103
D105
SLR-325DCT
SLR-325DCT
SLR-325DCT
D102
D104
TALLY
TALLY
TALLY
SLR-325DCT
SLR-325DCT
TALLY
TALLY
YA(TALLY)
B-SS3280<AEP>-YA.
2
CN201
4P
OVER LOAD
STANDBY
POWER
+5V
1
2
3
4
+5V
TO TB BOARD
CN6(3-6pin)
POWER
D203
SLR-325MCT31
LED
STANDBY
D202
SLR-325VCT31
LED
OVER LOAD
D201
SLR-325DCT31
LED
YB(INDICATOR)
B-SS3280<AEP>-YB.
3
CN301
8P
NC
NC
RTS
GND
NC
TXD
+5V
RXD
1
2
3
4
5
6
7
8
YC(RELAY)
CN302
S-DIN 8P
1
2
3
4
5
6
7
8
NC
NC
RTS
GND
NC
TXD
+5V
RXD
2
5
8
1
3
6
+5V
TO TB BOARD
CN7
B-SS3280<AEP>-YC.
4
(BVM-14G1/20G1,BKM-10R)
MONITOR
CONTROL UNIT
(BKM-10R)
(BVM-14G1/20G1)
CN101
9P
D-SUB-L
CN102
9P
JW1
(5)
JW2
(10)
6 7 8
1 2 3
+5V
9
4 5
HD (RERAY)
1
2
3
4
5
6
7
8
9
GND
TXD
RXD
GND
+5V
GND
TXD
RXD
GND
TO TB BOARD
CN8
5
D105
D102
D101
RD6.2SB
RD6.2SB
RD6.2SB
PROTECTOR PROTECTOR PROTECTOR
D104
D103
RD6.2SB
RD6.2SB
PROTECTOR PROTECTOR
B-SS3280<AEP>-HD.
11-45
A
B
C
D
E
F
G
H
G (1/2)
1
G (1/2)
+12V(SEC)(2/2)
RELAY DRIVE (2/2)
RELAY DET1 (2/2)
MAIN ON/OFF(2/2)
+20V(PRI) (2/2)
PFC OVP RESET (2/2)
+15V(PRI) (2/2)
GND(SEC) (2/2)
PFC DET (2/2)
PFC OUT (2/2)
LOW-B FAILE(2/2)
+20V
D103
Q105
Q106
IC101(1/2)
SLR-325VCT31 2SC2412K 2SA1037K LM393PS
PFC OVP IND
LATCH
LATCH COMPARATOR
Q109
2SC2412K
BUFFER
R115
1k
:CHIP
IC101(2/2)
LM393PS R106
100k
COMPARATOR :CHIP
R102
47k
:CHIP
R108
10k
:CHIP
2
1
C102
100
16V
:HT
C101
47
25V
:HT
R4
22k
2W
:RS
R11
150k
R19
R20
2.2k 2.2k
1/2W 1/2W
:FPRD :FPRD
R5
22k
2W
:RS
DEGAUSS COIL
S901
MAIN POWER
C12
10
:HT
RY901
2
1
3
4
R70
10
:FPRD
C14
220 R9
16V 10k
:HT :CHIP
FB33
0.45U
R53
330k
:RN
R58
220k
:RN
FB34
0.45U
R54
330k
:RN
R59
220k
:RN
R55
330k
:RN
R60
220k
:RN
R21
100k
R13
150k
Q4
2SC3840K
PROTECTOR
D35
D1NS4-TR2
DISCHRGE
R22
100k
D3
RD24ESB1
PROTECTOR
C15
10
:HT
R16
47k
D2
RD20ES-T1B1
REF
Q7
DTC144EKA
RESET
R23
47k
C17
10
:HT
R51
10
:FPRD
TP31
R66
220k
:RN
R67
220k
:RN
R52
10k
C45
22
25V
:BP
IC32(1/2)
NJM4558M-TE2
GAIN CTRL
TP32
R64
47k
:CHIP
R61
12k
:RN-CP
R57
2.7k
:RN-CP
C44
10
:HT
R63
560
R62
8.2k :RN-CP
:RN-CP
Q32
2SC2412K
GAIN CTRL
D4
SLR-325VCT31
PROT IND
R73 TP33
10k
:CHIP
P.GND
IC32(2/2)
NJM4558M-TE2
GAIN CTRL
8
5
6
7
S
FB31
0.45U
FB32
0.45U
R68
220k
:RN
V.PFC RTN
C43
220
450V
Q31
2SK2209
PFC OUT
C47
22
:HT
R31
0.22
5W
:RB
VDR2
4
3
2
1
C46
0.1
25V
B:CHIP
R69
8.2k
:RN-CP
R65
100k
:CHIP
1
3 THP1 2
7
6
5
4
3
2
1
C42
100
35V
:HT
4
1
C2
C3
0.0047 0.0047
250V
250V 3
E
E
2
T2
LFT
16
GATE DRV
D34
RD24ES-T1B1
PROTECTOR
C41
0.01
F:CHIP
C39
0.22
16V
B:CHIP
15
14
VCC
CT
C4
C5 4
0.0047 0.0047
250V
250V
E
E
1
3
2
GND
PK LMT
1
C31
0.001
B:CHIP
F1
T4A H/250V
VDR1
TNR14V47LK660
C36
0.1
F:CHIP
R50
12k
:RN-CP
13
C37
0.033
25V
B:CHIP
12
SOFT START R SET
CA OUT
2
R1
820k
1/2W
:RC
3
2
1
Q9
DTC144EKA
PFC OFF
11
V SENSE
10
9
ENABLE
V REF
IC31
TK83854D
PFC CTRL
C1
0.47
250V
:AC
CN1
2P
WHT
:VH
R47
22k
:CHIP
C38
0.1
25V
B:CHIP
R48
47k
:CHIP
R49
330k
:CHIP
C40
0.001
50V
:PPS-CP
C6
0.47
250V
:AC
4
NEUTRAL
D36
D5L60
RECTIFIRE
R56
15k
:RN-CP
CN2
4P
WHT
:VH
LIVE
R12
150k
R15
100k
R8
330k
T1
LFT
AC IN
100-240V
50/60Hz
R74
0.47
1/2W
:FUSE
T3
PFCT
R14
100k
R7
330k
Q1
2SC3840K
KICK
D901
1SS119
PROTECTOR
AC SW OUT
Q8
2SA1413
PROTECTOR
Q5
2SA1413
PROTECTOR
R6
330k
+12V
AC SW IN
D5
D1NS4-TR2
SWITCH
R10
10k
:CHIP
Q2
2SC3840K
KICK
AC SW OUT
R17
10k
:CHIP
V.PFC
R3
22k
2W
:RS
C11
0.47
630V
:MPS
AC SW IN
Q107
DTC144EKA
RESET
7
C10
0.0047
250V
E
R18
10k
:CHIP
Q110
DTC144EKA
RESET
8
C9
0.0047
250V
E
+15V
6
C8
0.0047
250V
E
+20V
C104
47
25V
:HT
R114
1k
:CHIP
9
C7
0.0047
250V
E
+12V
D8
MA111-TX
PROTECTOR
C16
47
25V
:HT
5
R2
3.3
10W
:RB
D104
D102
MA111-TX MA111-TX
SWITCH
SWITCH
D106
RD18ESB3
PROTECTOR
10
D1
D4SB60L
RECTIFIRE
Q104
R105
DTC144EKA 1.8k
PFC OFF :CHIP
Q6
2SB1261K
SWITCH
4
Q103
DTC144EKA
DISCHARGE
3 RY14
3
C105
0.01
F:CHIP
D6
D1NS4-TR2
SWITCH
I
G
11
2
O
R113
22k
:CHIP
5
R110 R112
4.7k 10k
:CHIP :RN-CP
IC1
D9
NJM7815FA
15V REG D1NS4-TR2
SWITCH
+15V
7
3
4
2
C103
10
:HT
8 6
Q101
2SC2785
RLY DRV
D101
1SS119
PROTECTOR
1
Q108
DTA144EKA
SWITCH
R111
10k
:RN-CP
12
R101
220
1W
:RS
R109
22k
:CHIP
R107
10k
:CHIP
R103 R104
22k 22k
:CHIP:CHIP
1
Q102
DTA144EKA
RLY DET
D105
RD12SB2-T1
LVL SHIFT
I SENSE
MPX OUT
4
5
3
C32
100p
CH:CHIP
R37
3.9k
:RN-CP
R35
22k
:CHIP
C33
0.001
B:CHIP
R33
1.2k
:RN-CP
D31
D1NS4-TR2 R34
CLAMP
7.5k
:RN-CP
D32
RD7.5M-T1B2
LIMTTER
D33
D1NS4-TR2
CLAMP
IAC IN
VA OUT
6
G
VRMS IN
7
(1/2)
(PFC CONTROL,MAIN RECT)
8
Note: As there are two kinds of ground on this borad.
be careful when measuring the voltages.
R41
R40
220k 330k C35
:CHIP :CHIP 1
:MPS
R46
22k
:CHIP
R39
330k
:CHIP
R36
3.9k
:RN-CP
B-SS3280<AEP>-G..-P1
C34
1
:MPS
R38
330k
:CHIP
R42
330k
:CHIP
R45
100k
:CHIP
R43
330k
:CHIP
R44
330k
:CHIP
5
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
11-46
A
B
C
D
11-46
E
F
G
H
G (2/2)
G (2/2)
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.
The components identified marked ! are
critical for safety.
Replace only with the part number specified.
TP201
D+5V
16
15
2
14
11
R237
100
2W
:RS
6
13
12
R203
470
:CHIP
+IN1 -IN1 F.B D.T
D211
MA111-TX
PROTECTOR
11
10
9
C2
E2
E1
R211 C204
22k 22
:RN-CP :HT
IC201
TL494CNS
PWM CTRL
1
2
3
4
CT
RT
GND
C1
5
6
7
8
C207
0.047
:MPS R219
1k
S
FB201
0.45U
Q205
2SK2766-01R-F165
CONVERTER OUT
10
D210
MA111-TX
SWITCH
R220
0.22
5W
:RB
PH201
PC123FY2
ISORATOR
R232
Q203
2SC3392-5-TB
BUFFER
1
3
2
4
PH803
PC123FY2
ISORATOR
R210
10k
:CHIP
R200
10k
:CHIP
4
3
3
1
D212
RD18ESB3
PROTECTOR
2
16.3
PH901
PC123FY2
ISORATOR
Q206
DTC144EKA
PROTECTOR
Q904
DTC144EKA
RESET
8.0
Q802
DTC144EKA
SWITCH
0.1
0.1
R264
680
:FPRD
5.3
6
7
1
5.3
R824
3.3k
:CHIP
Q817
DTA144EKA
SWITCH
R808
10k
:CHIP
IC804
R826
TL431CLP-Z 2.2k
+16V OVP :RN-CP
0
R809
10k
:CHIP
D812
RD5.1SB3
LVL SHIFT
R265
680
:FPRD
4
5
2
R811
2.7k
:RN-CP
C806
47
R812
25V
2k
:HT :RN-CP
3
2.6
2.6
2
1
R815
R816
2.2k
2.2k
:RN-CP :RN-CP
R817
12k
:RN-CP
0
T301
HI-B
15
2
14
R323
100k
2W
:RS
C306 C305
47
0.1
25V
25V
:HT B:CHIP
R314
220
:CHIP
R312
220
:CHIP
R317
10k
R315
10k
:CHIP
D306
M111-TX
PROTECTOR
R313
10k
:CHIP
R301
10k
:CHIP
R302
150
:CHIP
16
C301
0.1
25V
B:CHIP
15
14
13
12
+IN2 -IN2 Vref O.C Vcc
R304
10k
:CHIP
11
10
9
C2
E2
E1
+IN1 -IN1 F.B D.T
1
2
3
4
R311 C304
22k
22
:RN-CP :HT
CT
RT
GND
C1
5
6
7
8
13
4
12
5
11
C307
47
10V R319
:HT 1k
IC301
TL494CNS
PWM CTRL
R303
470
:CHIP
D302
RGP15K
CLAMP
R318
100k
C311
1000p
500V
E
L302
22µ
C317 C318
220 220
160V 160V
:HT :HT
C319
0.22
:MPS
R331
270
10W
:RN
C321
47
10V
:HT
R307 R308 C303
R309 R310
C302
2.2k 5.6k 0.001
12k 10k
0.1
:CHIP:RN-CP 50V :RN-CP :CHIP
25V
B:CHIP
:PPS-CP
Q304
D307
2SA1338-5-TB RD18ESB3
BUFFER
PROTECTOR
Q301
2SC2412K
SWITCH
R290
10k
:CHIP
1
3
2
R339
0.22
5W
:RB
R340
1k
:RN-CP
R333
10k
:CHIP
G
4
1
3
2
Q306
DTC144EKA
SWITCH
4.2
13
10
11
Q807
DTA144EKA
LATCH
C809
10
:HT
0.1
0
C902
0.0047
250V
E
0
C810
10
:HT
Q808
DTC144EKA
RESET
0.1
Q806
DTC144EKA
LATCH
R805
1M
:CHIP
D804
MA111-TX
RECT
D806
MA111-TX
SWITCH
Q810
DTA144EKA
LATCH
D807
MA111-TX
SWITCH
Q809
DTC144EKA
LATCH
G4
5.3
5.2
0.1
0
0
Q815
DTC144EKA
PROT
C805
10
:HT
D801
SLR-325MCT31
PFC IND
5.2
5.2
D803
MA111-TX
RECT
R804
1.5k
:CHIP
5.3
R821
10k
:CHIP
C802
0.47
16V
F:CHIP
Q811
DTC144EKA
RESET
G2
5.3
R231
10
:CHIP
3.0
12
120V RTN
1.3
Q805
DTC144EKA
PFC PROT
R806
10k
:CHIP
3
2.6
2
Q812
Q813
Q814
DTC144EKA DTC144EKA DTA124EKA
PWR SW
E PROT
PROT
C807
10
:HT
R901
3.3M
1/2W
:RC
R802
2.2k
:CHIP
D+5V
4.2
C901
0.0047
250V
E
R338
2k
:RN-CP
IC302
TL431CLP-Z
+120V REG
R823
1k
:CHIP
C804
47
25V
:HT
R803
4.7k
:CHIP
R801
1k
:CHIP
TP307
0.1
RELAY DET1 (1/2)
(2/2)
PWM CONTROL,CONVERTER OUT,PROTECTOR ENCODER
+5V,D+5V,± 6V,± 15V,+120V,HT RECT
PH802
PC123FY2
ISORATOR
R337
47k
1/2W
:RN
1
25.3
C325
0.01
F:CHIP
R291 C324
10k 0.01
:CHIP F:CHIP
Note:As there are two kinds of ground on this board.
be careful when measuring the voltages.
TP305
3
8
4
C320
0.22
200V
:PP
120V
IC801(1/4)
LM339NS-E20
COMPARATOR
24.8
TP306
Q300
DTA144EKA
SWITCH
R316
10
:FPRD
R334
100
:FPRD
TP303
TP304 GND
R336
47k
1/2W
:RN
R335
100
:FPRD
7
PH301
PC123FY2
ISORATOR
Q303
2SC3392-5-TB
BUFFER
R814
220k
1/2W
:RN
+120V
24.8
R306
10k
:CHIP
TP302
R332
33k
2W
:RS
6
10
D300
M111-TX
SWITCH
D305
MA111-TX
SWITCH
HT(-)
C312
1000p
500V
E
C315
680p
2kV
B
S
R320
0.22
5W
:RB
R833
100
:CHIP
TP301
C314
1000
10V
:HT
C313
1000
10V
:HT
G4
HT(+)
L301
22µ
D304
D5L60
+120V RECT
C316
680p
2kV
B
FB301
0.45U
R820
2.2k
:RN-CP
3
R328
22
2W
:RS
R324
100k
2W
:RS
Q305
2SK2766-01R-F165
CONVERTER OUT
D303
D5SC4M
6.5V RECT
R830
100
:CHIP
R831 G1
100
:CHIP G2
R832
100 G3
:CHIP
0.9
*
IC801(4/4)
LM339NS-E20
COMPARATOR
R329
0.47
1/2W
:FPRD
C308
0.022
630V
:PP
R819
4.7k
:RN-CP
+120V
R322
100k
2W
:RS
R818
22k
:RN-CP
8
9
14
1
R321
100k
2W
:RS
IC802
TL431CLP-Z
REF
R813
1k
:CHIP
2.6
2.4
IC801(3/4)
LM339NS-E20
COMPARATOR
R827
3.3k
:CHIP
R266
680
:FPRD
D+5V
IC801(2/4)
LM339NS-E20
COMPARATOR
0
D811
RD5.1SB3
LVL SHIFT
5.3
3.3
Q215
DTA144EKA
-16V DRV
2
D810
RD7.5M-T1B2
LVL SHIFT
0.1
Q816
DTC144EKA
SWITCH
-15V
1
+15V RTN
4
R260
680
:FPRD
-3.4
R263
680
:FPRD
Q801
DTA144EKA
+5V OVP
2
R907
:CHIP
17.0 3.3k
LOW-B FAILE (1/2)
PFC OVP RESET
(1/2)
2.6
-6V
-17.7
2
3
Q204
2SA1338-5-TB
BUFFER
3
-6.3
-17.0
R825
15k
:RN-CP
1
R216
10
:FPRD
R207 R208 C203
R209
2.2k 5.6k 0.001
12k
:CHIP :RN-CP 50V :RN-CP
:PPS-CP
2.5
1
IC203
TL431CLP-Z
+16V REG
Q902
DTC144EKA
+120V
SWITCH
+6V
15.8
R236
12k
:RN-CP
R234
2.2k
:RN-CP
TP207
Q903
DTC144EKA
SWITCH
CN3
64P
B TO B
Q213
DTA144EKA
-6V DRV +15V
6.5
R262
10k
:CHIP
C229
2200
25V
:HT
C228
2200
25V
:HT
Q211
DTC144EKA
+6V DRV
4.0
-17.7
+16V
11.2
R807
3.3k
:CHIP
C217
0.1
50V
B:CHIP
R235
100
:CHIP
C216
0.022
50V
B:CHIP
R233
100
:CHIP
3.3k
12.2 :CHIP
0.1
C904
100
16V
:HT
R259
Q214
680
2SC3746
:FPRD
-16V SWITCH
R261
680
2W
:RS
-16V
8
R218
100k
C200
0.1
25V
B:CHIP
7
T201
LOW-B
R202
47
:CHIP
MAIN ON/OFF (1/2)
D208
D5LC20U
-7V RECT
D209
D5LC20U
-16V RECT
5.1
16.9
-7.0
R258
10k
:CHIP
R257
470
1/2W
R904
10k
:CHIP
A0
D9
D1
D2
D3
A3
NC
Vcc
GND
A1
A2
D8
D7
D6
D5
D4
D+5V
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
A9
B9
A10
B10
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
A16
B16
A17
B17
A18
B18
A19
B19
A20
B20
A21
B21
A22
B22
A23
B23
A24
B24
A25
B25
A26
B26
A27
B27
A28
B28
A29
B29
A30
B30
A31
B31
A32
B32
8
14
C227
4700
10V
:HT
0.1
R906
2.2k
:CHIP
+6V
Q210
2SA1469
+6V SWITCH
Q212
2SC3746
-6V SWITCH
-7.1
C226
4700
10V
:HT
Q209
DTC144EKA
+16V DRV
10k
:CHIP
0
7
15
+IN2 -IN2 Vref O.C Vcc
5.1
6.1
R254
470
1/2W
12.7 DEG SWITCH R903
C903
47
25V
:HT
6.8
R256
330
:FPRD
Q901
2SC2785
O
G
6
16
C201
0.1
25V
B:CHIP
C223
4700
10V
:HT
-7V
R240
100
2W
:RS
R217
10k
R213
10k
:CHIP
C222
4700
10V
:HT
12.7
I
5
R224
100k
2W
:RS
5
F202
5A/125V
16.9
R252 R253
470
470
:FPRD :FPRD
4
R223
100k
2W
:RS
R206
10k
:CHIP
12
C224
1000p
500V
E
C225
1000p
500V
E
R255
10k
:CHIP
+7V
TP202
5.3
5.3
5.1
4.2
G3
G1
GND
GND
+120V
+120V
GND
GND
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
POWER ON
DEGAUSS
E PROT
G PROT1
G PROT2
G PROT3
G PROT4
GND
GND
VD
AFC PULSE
HS
VS
2HS
2VS
HT(+)
HT(+)
HT(-)
HT(-)
NC24A
V BLK 1
H BLK
V BLK2
+5V SENSE
RESET
NC
MISO
MOSI
SCLK
DIGITAL +5V
DIGITAL +5V
DIGITAL GND
DIGITAL GND
INTERNAL SIG
IRQ
GND
GND
TO TA BOARD
CN12
3
R215
10k
:CHIP
R204
10k
:CHIP
C219
1000p
500V
E
2.6
D.GND
D205
SLR-325MCT31
+5V IND
IC901
NJM7812FA
+12V REG
16.9
16.2
6.9
R250
680
2W
:RS
R230
2.2k
:CHIP
+12V
1
2
R201
10k
:CHIP
D207
D5LC20U
7V RECT
4
C221
2200
25V
:HT
C220
2200
25V
:HT
R248 R249
2.2k 2.2k
:RN-CP :RN-CP
3
2
Q208
R251
2SA1469
10k
+16V SWITCH :CHIP
+16V
C218
1000p
500V
E
D202
RGP15K
CLAMP
C215 6.1 Q207
4700
2SC3746
10V
:HT
+5V OUT
3
13
R212
220
:CHIP
R214
220
:CHIP
IC202
TL431CLP-Z
+5V REG
17.0
C208
0.022
630V
:PP
C206 C205
47
0.1
25V
25V
:HT B:CHIP
4.8
R247
22
1
R222
100k
2W
:RS
R246
22
C214
4700
10V
:HT
F201
5A/125V
D206
D5LC20U
+16V RECT
R221
100k
2W
:RS
L201
22µ
+7V
1
1.3
R228
D203
0.47
EGP10D
1/2W
+20V RECT :FPRD
1
5.2
IC803
MC74HC147
ENCODER
C211
470
50V
:HT
7.3
16 15 14 13 12 11 10 9
+20V
D204
D5LC20U
+7V RECT
R229
22
2W
:RS
D.5V
2.6
+12V
+15V
C213
1000p
500V
E
0.1
C212
1000p
500V
E
2.2
(1/2)
PFC DET
RELAY DRIVE(1/2)
(1/2)
GND(SEC)
+12V(SEC) (1/2)
+15V(PRI) (1/2)
+20V(PRI) (1/2)
(1/2)
PFC OUT
R902
3.3M
1/2W
:RC
B-SS3280<AEP>-G..-P2
11-47
A
B
C
D
11-47
E
F
G
H
2
3
4
5
G
G Board IC Block Diagrams
MC74HC147FEL (IC803)
D4
1
16 VCC
D5
2
15 NC
D6
3
14 A3
D7
4
13 D3
D8
5
12 D2
A2
6
11 D1
A1
7
10 D9
GND
8
9
A0
TL494CNS (IC201, 301)
ERROR AMP 1(+)
1
16
ERROR AMP 2(+)
ERROR AMP 1(-)
2
15
ERROR AMP 2(-)
FEEDBACK
3
DEAD TIME CONT
4
CT
5
5V REF
REG
OSC
RT
6
14
REF 5V REG
13
OUTPUT CONT
12
VCC
11
COLLECTOR-2
F.F
Q
Q
GND
7
10 EMITTER-2
COLLECTOR-1
8
9
EMITTER-1
11-48
BVM-14G5, BKM-10R
SO 12
16 BIT SHIFT
16BITREGISTER
LATCH
D OUT
CK
D IN
TO HC BOARD
CN5
15 STB
14 CLK
13 DATA
6
5
4
3
2
1
R207
1k
:CHIP
1.9
TP204
R206
1.9
1k
:CHIP
0.5
5.1
0
R205
100k
:CHIP
R215
47k
:CHIP
5.1
0
0
DATA
CLK
STB
CLR
P16
VSS
P15
P14
P13
P12
P11
VDD
SO
P1
P2
P3
P4
P5
VSS
P6
P7
P8
P9
P10
0
0
0
0
0
0
S216
D216
MA111 SWITCH
S217
D217
MA111 SWITCH
S218
D218
MA111 SWITCH
S219
D219
MA111 SWITCH
S220
D220
MA111 SWITCH
0
1.9
0.5
5.1
R210
100k
:CHIP
0
0
0
0
+5V
0
0
0
0
0
S221
D221
MA111 SWITCH
S222
D222
MA111 SWITCH
R201
560
:CHIP
DATA
CLK
STB
CLR
P16
VSS
P15
P14
P13
P12
P11
VDD
SO
P1
P2
P3
P4
P5
VSS
P6
P7
P8
P9
P10
9 10 11 12
P1 11
STB
CE2
MISO
MOSI
SCLK
+5V
GND
IC201
CXP2003M
S/P CONV1
8
P2 10
16 CLR
S201
D215
MA111 SWITCH
0
0
0
0
0
0
0
0
0
0
(CONTRAST)
R202
560
:CHIP
D223
CL-155Y/PG
(BRIGHT)
R203
560
:CHIP
S202
D202
MA111 SWITCH
S203
D203
MA111 SWITCH
S204
D204
MA111 SWITCH
S205
D205
MA111 SWITCH
S206
D206
MA111 SWITCH
S207
D207
MA111 SWITCH
S208
D208
MA111 SWITCH
S209
D209
MA111 SWITCH
S210
D210
MA111 SWITCH
S211
D211
MA111 SWITCH
S212
D212
MA111 SWITCH
S213
D213
MA111 SWITCH
D224
CL-155Y/PG
(CHROMA)
R204
560
:CHIP
D201
MA111 SWITCH
C306
0.01
S232
50V
F:CHIP BRIGHT
R306
4.7k
:CHIP
PD5
2
PD4
3
1
R305
4.7k
:CHIP
S214
D225
CL-155Y/PG
D214
MA111 SWITCH
C304
0.01
S233
50V
F:CHIP CHROMA
R304
4.7k
:CHIP
PD3
2
PD2
3
1
R303
4.7k
:CHIP
C303
0.01
50V
F:CHIP
C302
S234
0.01 PHASE
50V
F:CHIP
R302
4.7k
:CHIP
PD1
2
PD0
3
1
R301
4.7k
:CHIP
R211
33k
:CHIP
0
R212
82k
:CHIP
R213
33k
:CHIP
+5V
0.3
TP201
TP205
0.3
0
Q203
2SD1834
GREEN LED DRIVE
R214
82k
:CHIP
+5V
C201
100
6.3V
Q202
2SD1834
ORENGE LED DRIVE
C202
100
6.3V
C203
100
6.3V
C204
100
6.3V
C205
100
6.3V
C206
100
6.3V
C207
100
6.3V
3
C301
0.01
50V
F:CHIP
(PHASE)
D226
CL-155Y/PG
2
C305
0.01
50V
F:CHIP
7
17 P16
CL
16 BIT LATCH
S215
IC202
CXP2003M
S/P CONV2
6
9
R217 47k :CHIP
R208
4.7k
:CHIP
R216
47k
:CHIP
5
8
P3
CN201
6P
WHT
:S-MYCRO
4
18 GND
C307
0.01
50V
F:CHIP
R209
1k :CHIP
3
19 P15
7
3
R307
4.7k
:CHIP
2
6
P5
PD6
0
1
GND
2
TP202 TP203
24 23 22 21 20 19 18 17 16 15 14 13
20 P14
9 10 11 12
21 P13
5
8
4
P6
7
P7
PD7
1
Q201
DTC144EKA-T146
SWITCH OUT
1.9
6
22 P12
5
3
4
P8
C308
0.01
50V
F:CHIP
R308
4.7k
:CHIP
D231
RD6.2SB-T1
3
23 P11
1
CONTRAST
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
2
2
S231
+5V
+5V
1
P9
P4
TO HC BOARD
CN3
24 VDD
GND
1
+5V
2
ENCODER0 3
ENCODER0 4
ENCODER1 5
ENCODER1 6
ENCODER2 7
ENCODER2 8
ENCODER3 9
ENCODER3 10
24 23 22 21 20 19 18 17 16 15 14 13
CXP2003M (IC201, 202)
1
HA BVM-14G5, BKM-10R
CN202
10P
WHT
:S-MYCRO
HA Board IC Block Diagram
P10
HA
C211 C212 C213 C214 C215 C216 C217
0.01 0.01 0.01 0.01 0.01 0.01 0.01
50V
50V
50V
50V
50V 50V
50V
F:CHIP F:CHIP F:CHIP F:CHIP F:CHIPF:CHIP F:CHIP
FUNCTION OF SWITCH
S201 POWER
S202 DEGAUSS
S203 INPUT1
S204 INPUT2
S205 INPUT3
S206 INPUT0
S207 INPUT4
S208 INPUT5
S209 INPUT6
S210 INPUT DEL
S211 INPUT7
S212
S213
S214
S215
S216
S217
S218
S219
S220
S221
S222
INPUT8
INPUT9
INPUT ENT
MANUAL CONTRAST
MANUAL BRIGHT
MANUAL CHROMA
MANUAL PHASE
MENU
ENTER
UP
DOWN
HA
(FUNCTION CONTROL)
4
B-SS3280<AEP>-HA.
5
11-49
A
B
C
D
11-49
E
F
G
H
BVM-14G5, BKM-10R
HB
HB BVM-14G5, BKM-10R
HB Board IC Block Diagram
+5V
0
R117
4.7k
:CHIP
IC102
NJU3716M
S/P CONV2
R115
1k
:CHIP
Q103
DTC144EKA-T146
SWITCH OUT
S107
D107
MA111 SWITCH
S108
D108
MA111 SWITCH
IC101
NJU3716M
S/P CONV1
COMB/B
S101
D101
MA111 SWITCH
S102
D102
MA111 SWITCH
CXP2003M (IC101, 102)
SHIFT
P14
P6
P13
P7
P12
P8
P11
P9
VDD
P10
0
0
0
0
0
D127
CL-155Y/PG
R107
560
:CHIP
0
0
(COMB/B)
2
R108
560
:CHIP
D128
CL-155Y/PG
R109
560
:CHIP
D129
CL-155Y/PG
R110
560
:CHIP
D130
CL-155Y/PG
9 10 11 12
8
/BLUE ONLY
S105
D105
MA111 SWITCH
1
24 VDD
P9
2
23 P11
P8
3
22 P12
P7
4
21 P13
P6
5
20 P14
GND
6
19 P15
P5
7
18 GND
P4
8
P3
9
MON/R
7
VSS
P10
/SYNC
D104
S104
MA111 SWITCH
S106
6
P5
P15
D103
MA111 SWITCH
D106
MA111 SWITCH
APT/G
5
0
VSS
S103
0
0
0
0
0
17 P16
0
4
R116 100k :CHIP
ADDRESS/SAFE AREA
SO
P1
P2
P3
P4
P5
VSS
P6
P7
P8
P9
P10
3
P4
D110
S110
MA111 SWITCH
DATA
CLK
STB
CLR
P16
VSS
P15
P14
P13
P12
P11
VDD
2
P16
0
1.9
0.3
5.1
D109
MA111 SWITCH
F2/F4
8
P3
S109
0
0
R101
560
:CHIP
D121
CL-155Y/PG
+5V
CL
16 BIT LATCH
P2 10
TP101
P1 11
R102
560
:CHIP
D122
CL-155Y/PG
R103
560
:CHIP
D123
CL-155Y/PG
R104
560
:CHIP
D124
CL-155Y/PG
R105
560
:CHIP
D125
CL-155Y/PG
R106
560
:CHIP
D126
CL-155Y/PG
STB
16 CLR
15 STB
TP102
1
0
0
P2
CLR
0
0
0
0
0
/16:9
24 23 22 21 20 19 18 17 16 15 14 13
D111
RD6.2SB-T1
PROTECTOR
STB
7
100k
:CHIP
P1
6
0.3
R112 5.1
SO
CLK
5
R113 1k :CHIP
1.8
DATA
1.9
4
R114 1k :CHIP
9 10 11 12
F1/F3
3
CE1
6
5
MISO
4
MOSI
3
SCLK
2
+5V
1
GND
TO HC BOARD R125
47k
CN4 :CHIP
R127
47k
:CHIP
2
R126
47k
:CHIP
1
CN101
6P
RED
:SMYCRO
24 23 22 21 20 19 18 17 16 15 14 13
1
5.1
SO 12
16 BIT SHIFT
16BITREGISTER
LATCH
D OUT
CK
D IN
14 CLK
13 DATA
(F1/F3)
(F2/F4)
(ADDRESS/SAFE AREA)
Q101
2SD1834
ORENGE LED DRIVE
+5V
C101
47
6.3V
3
C102
47
6.3V
C111
C112
0.01
0.01
50V
50V
F:CHIP F:CHIP
C113
0.01
50V
F:CHIP
R121
33k
:CHIP
R122
82k
:CHIP
R124
82k
:CHIP
R123
33k
:CHIP
HB
Q102
2SD1834
GREEN LED DRIVE
(FUNCTION CONTROL)
B-SS3280<AEP>-HB.
4
5
11-50
A
B
C
D
11-50
E
F
G
H
+5V
A10
A8
GND
Y8
RD
A7
A6
A5
A4
A3
A2
A1
A0
A11
A9
A8
A13
WR
IC14(4/4)
TC74VHC02F(EL)
DECODER
G2
9 10
5.3
Y1
5.3
Y2
1.7
Y3
2.0
Y4
4.2
Y5
4.2
Y6
4.0
Y7
5.3
A8
GND
Y8
5.1
20 19 18 17 16 15 14 13 12 11
8
8
9 10
9 10
11
VCC
5.1
5.1
A2
1.7
A3
2.0
A4
4.2
A5
4.2
A6
4.0
A7
0
C66
0.01
F:CHIP
WR
RD
A13
A12
A11
A10
A9
A8
A12
A7
IC6
TC74VHC541F(EL) BUFFER
6
5.1
A4
5.3
2
3
4
5.1
5
5.3
5.3
9 10 11 12 13 14
5.3
C88
100
6.3V
AL-CP
WAIT
A3
R50
100k
:CHIP
A2
5.3
CE2
8
7
REG
A20
A19
A18
A17
A16
A15
A14
A6
WAIT
A5
R45
47k
:CHIP
1
+5V
5.3
TP9
7
BVD2
8
9
10
1
2
A1
14
14
IC7
TC74VHC574F(EL)
CARD ADDRESS
HIGH
RD
7
7
CK
A13
A12
A11
A10
A9
A8
6
6
GND
A1
5
5
A8
VCC
5.3
Y1
5.3
Y2
5.3
Y3
5.3
Y4
5.3
Y5
5.3
Y6
5.3
Y7
5.3
Y8
5.1
5.1
G1
4
4
5.3
A1
5.3
A2
5.3
A3
5.3
A4
5.3
A5
5.3
A6
5.3
A7
5.3
WR
RD
3
OE
11
12
13
2
9 0
8
NC
RDY
WP
CD2
BVD1
BVD2
WAIT
CD1
0
7
IC21
TC74VHC125F(EL)
+5V
BUFFER
IC14(3/4)
TC74VHC02F(EL)
DECODER
A0
BVD1
D0
CE1
D1
NC
RDY
WP
CD2
BVD2
BVD1
WAIT
CD1
C71
0.01
F:CHIP
R48
R49
3.3k 3.3k
:CHIP :CHIP
D2
3
4
34
WP
CD2
2
2
3
C89
100
6.3V
AL-CP
2.4
1
4
5
6
7
8
L3
100µH
+5V
PGND
OUT
6
AGND
NC
SHDN
7
IN
8
ILIM
4
C81
100
6.3V
AL-CP
3
D1
RD6.2SB-T1
DC SHIFT
B-SS3280<AEP>-HC.
L1
150µH
IC16
MAX877CSA
5V REGURATOR
R69
1k
:CHIP
2
1.3
5.3
5.1
5.5
5.2
5.2
5.2
5.2
1
9 10
20 19 18 17 16 15 14 13 12 11
R13 R16 R19
10k 10k 10k
:CHIP :CHIP :CHIP
R31
47k
R32
:CHIP 47k
R33 :CHIP
47k
R34
:CHIP 47k
R35 :CHIP
47k
R36
:CHIP 47k
R37 :CHIP
47k
R38
:CHIP 47k
:CHIP
D15
A10
CE2 CE2
OE
RFSH
A11
RFU
A9
RFU
A8
A17 A17
A13
A18 A18
A14 A14
A19 A19
WE/PGM
A20 A20
DRY/BSY
A21
VCC
C90
VCC
100
6.3V
AL-CP VPP1
VPP2
A16 A16
A22
A15 A15
A23
A12
A24
A7
A25
A6
RFU
A5
RESET
A4
WAIT
A3
RFU
A2
REG REG
A1
BVD2
A0
BVD1
D0
D8
D1
D9
D2
D10
WP
CD2
GND
GND
MEMORY CARD UNIT
G2
1.0
Y1
3.5
Y2
2.5
Y3
2.3
Y4
3.4
Y5
2.3
Y6
0.1
Y7
0
1
CE1
RDY
IC10(4/6)
TC74VHC14F(EL)
INVERTER
3.7
VCC
1.0
3.5
A2
2.5
A3
2.3
A4
3.4
A5
2.3
A6
0.1
A7
0
1
8
9 10
7
8
6
7
5
6
1
5
2
4
3
A1
3
4
CD1
20 19 18 17 16 15 14 13 12 11
G1
2
3
D7
D6
D5
D4
D3
D2
D1
D0
2
8
5.0
20 19 18 17 16 15 14 13 12 11
1
VCC
5.3
G
A1
5.3
5.3
A2 L B->A B1
5.3
5.3
A3 H A->B B2
5.3
5.3
A4
B3
5.3
5.3
A5
B4
5.3
5.3
A6
B5
5.3
5.3
A7
B6
5.3
5.3
A8
B7
5.3
GND
B8
5.3
20 19 18 17 16 15 14 13 12 11
Q2
DTC144EKA-T146
VPP 5V SW
5.0
HC
5
R15
10k
:CHIP
D7
RD6.2SB-T1
PROTECTOR
LX
+5V
C
5
C83
C84
C85
C86
C87
100
100
100
100
100
6.3V 6.3V 6.3V 6.3V 6.3V
AL-CP AL-CP AL-CP AL-CP AL-CP
C82
C52
220 0.01
6.3V F:CHIP
4.9
IC12
TC74VHC244F(EL)
BUS SHIFT
B
DIR
IC8
TC74VHC245F(EL)
BUFFER
0
L2
100µH
CPU,MEMORY CARD DRIVER
CARD ADDRESS DECODER,RS422 DRIVE
11-51
A
9 10
R18
R11
10k 5.0 6.8k
:CHIP
:CHIP
+5V
VCC
ENB
YA1
B4
YA2
B3
YA3
B2
YA4
B1
8
5.0
R40
4.7k
:CHIP
R12
10k
:CHIP
ENA
A1
YB4
A2
YB3
A3
YB2
A4
YB1
GND
7
R68
100k
:CHIP
1
7
R20
10k
:CHIP
6
R10
2.2k
:CHIP
R71
100k R72
:CHIP 100k
:CHIP
R73
100k R74
:CHIP 100k
:CHIP
R75
100k R76
:CHIP 100k
:CHIP
R77
100k R78
:CHIP100k
:CHIP
5.1
0
10
5
C67
0.01
F:CHIP
R5
10k
:CHIP
D0
D1
D2
D3
D4
D5
D6
D7
20 19 18 17 16 15 14 13 12 11
RD
WR
Q4
2SA1221T-KLM
VPP 5V REG 0
Q6
DTC144EKA-T146
VPP 5V SW
D7
D6
D5
D4
D3
D2
D1
D0
16 15 14 13 12 11 10 9
P72/BUSY
GND
GND
GND
D3
CD1
D4
D11
D5
D12
D6
D13
D7
D14
D0
D1
D2
IC5
TC74VHC541F(EL)
BUFFER
IC10(6/6)
TC74VHC14F(EL)
INVERTER
9 10
P71/OS
5.1
C92
100
6.3V
AL-CP
8
P73/IOS
G
5.3
B1
5.3
B2
5.3
B3
5.3
B4
5.3
B5
5.3
B6
5.3
B7
5.3
B8
5.3
+5V
A8
A9
A10
A11
A12
A13
A14
A15
7
P70/IS
Y6
6
4.6
GND
5
P74/AS
Y5
4
P75/WR
P55/SCK1
Y4
3
P54/RXD1
Y3
Y7
2
P76/RD
G2B
G1
1
5.3
5.1
5.1
P7/WAIT
Y2
8
VCC
G2A
IC3
TC74VHC138F(EL) ADDRESS DECODER
C93
100
6.3V
AL-CP
5.3
2.6
5.3
5.1
5.1
5.2
5.1
5.2
R44
10k
:CHIP
P27/A15
Y1
A7
A6
A5
A4
A3
A2
A1
A0
5.3
5.3
IC10(5/6)
TC74VHC14F(EL)
INVERTER
+5V
D6
RD6.2SB-T1
PROTECTOR
R43
10k
:CHIP
P43/TMCI1
0
4.0
P21/A9
4.2
P22/A10
4.2
P23/A11
2.0
P24/A12
1.7
P25/A13
1.2
P26/A14
1.2
Y0
C
7
6
CLK
5.1
5.0
5.0
P44/TMO1
5.1
P45/TMRI1
2.5
P46/PHAI
2.5
P47/E
5.1
P50/TXD0
5.2
P51/RXD0
5.1
P52/SCK0
5.1
P53/TXD1
4.6
P42/TMRI0
VSS
P20/A8
B
6
5
GND
P41//TMO0/
IOS
A7
VCC
5
4
D0
P40/TMCI0
A0
A1
A2
A3
A4
A5
A6
A7
A
4
5.3
Q7
5.3
Q6
5.3
Q5
5.3
Q4
5.3
Q3
5.3
Q2
5.3
Q1
5.3
Q0
0
P17/A7
5.1
5.3
5.3
A3
5.3
A4
5.3
A5
5.3
A6
5.3
A7
5.3
A8
5.3
IC4
TC74VHC245F(EL)
BUFFER
1 5.3
TP6TP7TP8
3.4
2.3
2.5
3.5
4.6
1.0
3
0
0
D6
0
D5
0
D4
0
D3
0
D2
0
D1
0
STBY
VSS
3
4
0 2
VCC
1.2
A3
A4
A5
A6
+5V
20 19 18 17 16 15 14 13 12 11
D7
3
R14
10k
:CHIP
VCC
2.3
5.1
MD0
0
NMI
5.1
VCC
5.1
MD1
13
5.1
IC11
TC74VHC574F(EL)
BUFFER
OE
1
EXTAL
A15
1.2 6
5
12
5.0
2
TP5
+5V
IC9(3/6)
TC74VHC14F(EL)
INVERTER
6
5
4
3
2
1
6
5
4
3
2
1
R70
100k
:CHIP
TP4
2
PROTECTOR
R41
R42
10k
10k
:CHIP :CHIP
CE2
MISO
MOSI
SCLK
+5V
GND
TO HA BOARD
CN201
0.1
3.7
IC10(2/6)
TC74VHC14F(EL)
INVERTER
IC9(4/6)
R60 R62 R64 R66
47k 47k 47k 47k
TC74VHC14F(EL)
:CHIP:CHIP:CHIP:CHIP IC10(1/6)
INVERTER
TC74VHC14F(EL)
IC9(6/6)
INVERTER
TC74VHC14F(EL)
IC9(1/6)
INVERTER
TC74VHC14F(EL)
INVERTER
6P
RED
DOUT
R7
100k
:CHIP
R61 R63 R65 R67
47k 47k 47k 47k
:CHIP:CHIP:CHIP:CHIP
CN5
DOUT
GND
IC13
LTC490CS8
RS422 DRIVE
3
4
10
EN0B
5.1
5
6
9
EN0A
5.113
12
8
EN1B
5.1
11
10
7
EN1A
5.1 9
8
6
EN2B
5.1
1
2
5
EN2A
5.1 3
4 14
4
EN3B
5.1
5
6
3
EN3A
5.1
2
+5V
IC9(2/6) 7
TC74VHC14F(EL)
1
GND
IC9(5/6)
TO HA BOARD
TC74VHC14F(EL)
D8
CN202
RD6.2SB-T1
CE1
MISO
MOSI
SCLK
+5V
GND
TO HB BOARD
CN101
DIN
+5V
D3
D5
RD6.2SB-T1 RD6.2SB-T1
PROTECTOR PROTECTOR
D2
D4
RD6.2SB-T1 RD6.2SB-T1
PROTECTOR PROTECTOR
CN4
6P
WHT
RIN
RIN
XTAL
A14
D7
D6
D5
D4
D3
D2
D1
D0
1
C50
0.01
F:CHIP
VCC
4.6
ROUT
5.1
5.3
5.3
P36/D6
5.3
P35/D5
5.3
P34/D4
5.3
P33/D3
5.3
P32/D2
5.3
P31/D1
5.3
P30/D0
0
P10/A0
0.1
P11/A1
2.3
P12/A2
3.4
P13/A3
2.3
P14/A4
2.5
P15/A5
3.5
P16/A6
1.0
P37/D7
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
TP3
1
CN3
10P
9
8
7
6
5
4
3
2
1
5.3
RES
2.1
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
GND
RXD
TXD
GND
+5V
GND
RXD
TXD
GND
TO TB BOARD
CN8
(BVM-14G5)
TO HD BOARD
CN102
(BKM-10R)
R4
10k
:CHIP
P66/IRQ2
8
C68
0.01
F:CHIP
CN2
9P
P65/IRQ1
7
R3
10k
:CHIP
P64/IRQ0
6
C2
10pF
CH:CHIP
P63/FTI
5
C1
10pF
CH:CHIP
P62/FTOB
4
2
3
C4
0.01
F:CHIP
P61/FTOA
3
R1
R2
10k
0
:CHIP :CHIP
X1
20MHz
2
1
R6
10k
:CHIP
5.3
1
IC2
PST529CMT
RESET
P60/FTCI
IC10(3/6)
TC74VHC14F(EL)
INVERTER
A2
4
IC1
HD6473258P10
CPU
A1
3
IC14(1/4)
TC74VHC02F(EL)
ENCODER
IC14(2/4)
TC74VHC02F(EL)
ENCODER
TP2
DIR
2
TP1
RD
D0
D1
D2
D3
D4
D5
D6
D7
1
R87 R89 R91 R93 R79 R81 R83 R85 R21 R23 R25 R27
100k 100k 100k 100k 100k 100k 100k 100k 1k 1k 1k 1k
:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP :CHIP:CHIP:CHIP:CHIP
R88 R90 R92 R94 R80 R82 R84 R86 R22 R24 R26 R28
100k 100k 100k 100k 100k 100k 100k 100k 1k 1k 1k 1k
:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP :CHIP:CHIP:CHIP:CHIP
+5V
CN1
68P
PCMCIA
R52 R54 R56 R58
100k 100k 100k 100k
:CHIP:CHIP:CHIP:CHIP
R51 R53 R55 R57
100k 100k 100k 100k
:CHIP:CHIP:CHIP:CHIP
+5V
1
C54
C56
C58
C60
C62
C64
0.01
0.01
0.01
0.01
0.01
0.01
C53 F:CHIP C55 F:CHIP C57 F:CHIP C59 F:CHIP C61 F:CHIP C63 F:CHIP C65
0.01
0.01
0.01
0.01
0.01
0.01
0.01
F:CHIP
F:CHIP
F:CHIP
F:CHIP
F:CHIP
F:CHIP
F:CHIP
HC BVM-14G5, BKM-10R
35
HC
68
BVM-14G5, BKM-10R
D
11-51
E
F
G
H
HC
HC Board Waveforms
HC Board IC Block Diagrams
1
TC74VHC138F (IC3)
Vcc
Y0
Y1
Y2
Y3
Y4
Y5
T6
16
15
14
13
12
11
10
9
Y0
Y1
Y2
Y3
Y4
Y5
C
G2A
G2B
G1
Y7
2.1Vp-p (20MHz)
A
Y6
B
1
2
3
4
5
6
7
8
A
B
C
G2A
G2B
G1
Y7
GND
TC74VHC245F (IC4, 8)
Vcc
ENABLE
G
B1
20
7
19
18
B2
B3
B4
B5
B6
B7
B8
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
9
10
DIR
A1
A2
A3
A4
A5
A6
A7
A8
GND
TC74VHC541F (IC5, 6)
G1
1
20 VDD
A1
2
19 G2
A2
3
18 Y1
A3
4
17 Y2
A4
5
16 Y3
A5
6
15 Y4
A6
7
14 Y5
A7
8
13 Y6
A8
9
12 Y7
GND 10
11 Y8
TC74VHC574F (IC7, 10)
Vcc
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
CLK
20
19
18
17
16
15
14
13
12
11
Q OE Q OE Q OE Q OE Q OE Q OE Q OE Q OE
D CK D CK D CK D CK D CK D CK D CK D CK
1
2
3
4
5
6
7
8
OC
1D
2D
3D
4D
5D
6D
7D
9
10
8D GND
11-52
A
B
C
D
E
F
G
H
TA
TA
3
2
1
LCC
LCC RTN
NC
LCC
LCC
LCC RETURN
CN20
3P
WHITE
:S-MICRO
LCC
(20G1)
ROTATION RETURN
ROTATION
2
1
ROT.RTN
ROTATION
ROTATION RETURN
ROTC
ROTATION
CN19
2P
WHT
:S-MICRO
NTC RETURN
NTC
NTC RETURN
NTC
2 NTC RETURN
NTC
1
CN14
50P
NTC
CN18
2P
WHT
:S-MICRO
B25
GND
A25
GND
B24
+120V
A24
+120V
B23
GND
A23
GND
B22
-15V
A22
-15V
B21
+15V
A21
+15V
B20
-6V
A20
-6V
B19
+6V
A19
+6V
B18
DUG
A18
DUB
B17
DUR
A17
VSP
B16 ABL OUT
A16 G2 CONTROL
B15 AFC PULSE
A15
HS
B14
VS
A14
2HS
B13
2VS
A13
NC22A
B12
NC22B
A12
NC23A
B11
NC23B
A11
NC24A
B10
V.BLK1
A10
H.BLK
B9
V.BLK2
A9 +5V.SENSE
B8
RESET
A8
NC27A
B7
MISO
A7
MOSI
B6 DIGITAL+5V
A6 DIGITAL+5V
B5 DIGITAL+5V
A5 DIGITAL+5V
B4 DIGITAL.GND
A4 DIGITAL.GND
B3 DIGITAL.GND
A3 DIGITAL.GND
B2 CH.SLOT2
A2 CH.SLOT1
B1
SCLK
A1 INTERNAL.SIG
TO TB BOARD
CN4
+120V
+120V
(20G1)
CY
CY
CY
CY
(V) RETURN
(V)
(H) RETURN
(H)
4 CY (V) RTN
3
CY (V)
2 CY (H) RTN
1
CY (H)
-15V
CY
-15V
+15V
+15V
CN17
4P
WHT
:S-MICRO
-6V
-6V
+6V
+6V
HT(-)
HT(+)
+12V
+12V(E)
-12V(E)
-12V
G2 CONTROL(E)
H STAT CONTROL(E)
8
H2
7
H1
6
GND
TO
5
+12V
C BOARD
4
-12V
CN508
3
GND
2
G2 CTRL
1 H.STAT CTRL
CN16
8P
WHITE
:S-MICRO
HV RETURN(DC)
HV OVP
+15V
+15V(IN)
+15V(OUT)
ABL1(IK PROT)
ABL2(ABL)
+15V(OUT)
+15V(IN)
HV RETURN(AC)
11 HV RTN(DC)
10
GND
9
HV PROT
8
GND
7
+15V(JW)
6
+15V(JW)
5
IK PROT
4
ABL OUT
3
+15V(JW)
2
+15V(JW)
1 HV RTN(AC)
CN15
11P
WHITE
:S-MICRO
TO
P BOARD
CN902
DUG
DUB
DUR
VSP
ABL OUT
G2 CONTROL
AFC PULSE
≠≠
HS
≠
≠≠
VS
≠
≠≠≠
2HS
≠≠
≠≠≠
2VS
≠≠
NC24A
V.BLK1
H.BLK
V.BLK2
D.5V RETURN
RESET
NC27A
MISO
MOSI
DIGITAL 5V
D+5V
≠≠≠≠≠≠≠≠
CH.SLOT2
≠≠≠≠≠≠≠
SCLK
INTERNAL SIG
TA(MOTHER)
CY (V) RETURN
CY (V)
CY (H) RETURN
CY (H)
HV OVP
HV RETURN(AC)
ABL2(ABL)
HV RETURN(DC)
+15V(IN)
ABL1(IK PROT)
+15V(OUT)
H STAT CONTROL(E)
G2 CONTROL(E)
+12V(E)
+12V
-12V(E)
-12V
B32
A32
B31
A31
B30
A30
B29
A29
B28
A28
B27
A27
B26
A26
B25
A25
B24
A24
B23
A23
B22
A22
B21
A21
B20
A20
B19
A19
B18
A18
B17
A17
B16
A16
B15
A15
B14
A14
B13
A13
B12
A12
B11
A11
B10
A10
B9
A9
B8
A8
B7
A7
B6
A6
B5
A5
B4
A4
B3
A3
B2
A2
B1
A1
GND
GND
LCC RET
LCC RET
LCC
LCC
ROT.RET
ROT.RET
ROT
ROT
NTC RET
NTC RET
NTC
NTC
CY (V) RET
CY (V) RET
CY (V)
CY (V)
CY (H) RET
CY (H) RET
CY (H)
CY (H)
HV PROT
HV R(AC)
ABL2
HV R(DC)
+15V
ABL1
+15V
NC
GND
GND
H.STAT C
G2 C
+12V
+12V
GND
GND
-12V
-12V
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
GND
GND
TO E BOARD(1/4)
CN802
B32
GND
A32
GND
B31
+B
A31
+B
B30
GND
A30
GND
B29
-15V
A29
-15V
B28
+15V
A28
+15V
B27
-6V
A27
-6V
B26
+6V
A26
+6V
B25
DU.G
A25
DU.B
B24
DU.R
A24
V.SP
B23
ABL
A23
G2.CNT
B22
HCR
A22
VCR
B21
H.CY
A21
V.CY
B20
H.STAT
A20
V.STAT
B19
HCT
A19 POWER.ON
B18
DEGAUSS
A18 E.PROTECT
B17 G.PROTECT1
A17 G.PROTECT2
B16 G.PROTECT3
A16 G.PROTECT4
B15
GND
A15
GND
B14
VD
A14
AFC.P
B13
HS
A13
VS
B12
2HS
A12
2VS
B11
NC
A11
NC
B10
NC
A10
NC
B9
HP
A9 V.BLK.P1
B8
H.BLK.P
A8 V.BLK.P2
B7 +5V.SENSE
A7
RESET
B6
NC
A6
MISO
B5
MOSI
A5
SCLK
B4 DIGITAL+5V
A4 DIGITAL+5V
B3 DIGITAL.GND
A3 DIGITAL.GND
B2 CH.SLOT2
A2 INTERNAL.SIG
B1
GND
A1
GND
TO E BOARD(1/4)
CN801
+120V
+120V
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
DUG
DUB
DUR
VSP
ABL OUT
G2 CONTROL
≠≠≠≠≠≠≠≠
POWER
≠≠≠≠≠≠≠
ON
≠≠≠≠≠≠≠
DEGAUSS
≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠
E.PROTECTOR
≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR1
≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR2
≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR3
≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR4
≠≠≠≠≠≠≠≠≠≠≠
VD
AFC PULSE
≠≠
HS
≠
≠≠
VS
≠
≠≠≠
2HS
≠≠
≠≠≠
2VS
≠≠
HT(+)
HT(-)
NC24A
V.BLK1
H.BLK
V.BLK2
D.5V RETURN
RESET
NC27A
MISO
MOSI
SCLK
DIGITAL 5V
D+5V
≠≠≠≠≠≠≠≠
CH.SLOT2
≠≠≠≠≠≠≠
INTERNAL SIG
-2
1
CN12
64P
B TO B
CN11
64P
B TO B
CN13
64P
B TO B
LCC RETURN
A1
GND
B1
GND
A2
+120V
B2
+120V
A3
GND
GND
B3
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
GND
A9
GND
B9
GND
A10
GND
B10
GND
A11
GND
B11
GND
A12
GND
B12
GND
A13
GND
B13
GND
A14
GND
B14 POWER.ON
DEGAUSS
A15
E.PROT
B15
G.PROT1
A16
G.PROT2
B16
G.PROT3
A17
G.PROT4
B17
GND
A18
GND
B18
VD
A19
B19 AFC.PULSE
HS
A20
VS
B20
2HS
A21
2VS
B21
HT(+)
A22
HT(+)
B22
HT(-)
A23
HT(-)
B23
NC24A
A24
V.BLK1
B24
H.BLK
A25
V.BLK2
B25
A26 +5V.SENSE
RESET
B26
NC
A27
MISO
B27
MOSI
A28
SCLK
B28
A29 DIGITAL+5V
B29 DIGITAL+5V
A30 DIGITAL.GND
B30 DIGITAL.GND
NC
A31
B31INTERNAL.SIG
GND
A32
GND
B32
TO G BOARD
CN3
+120V
+120V
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
≠≠≠≠≠≠≠≠
POWER
≠≠≠≠≠≠≠
ON
≠≠≠≠≠≠≠
DEGAUSS
≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠
E.PROTECTOR
≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR1
≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR2
≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR3
≠≠≠≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠≠≠≠≠
G.PROTECTOR4
≠≠≠≠≠≠≠≠≠≠≠
VD
AFC PULSE
≠≠
HS
≠
≠≠
VS
≠
≠≠≠
2HS
≠≠
≠≠≠
2VS
≠≠
HT(+)
HT(-)
NC24A
V.BLK1
H.BLK
V.BLK2
D.5V RETURN
RESET
NC27A
MISO
MOSI
SCLK
DIGITAL 5V
D+5V
INTERNAL SIG
-2
2
3
4
-2
B-SS3280<AEP>-TA.
11-53
A
B
C
D
5
11-53
E
F
G
H
TB
1
+12V
+12V
≠≠≠≠≠
TALLY
≠≠≠≠
≠≠≠≠≠≠≠≠
OVERLOAD
≠≠≠≠≠≠≠
STAND
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠
BY
≠≠≠≠≠
POWER
≠≠≠≠
+5V
1
2
3
4
5
6
+5V
TO YA BOARD
CN101
+12V
TALLY
OVERLOAD
STANDBY
POWER
+5V
CN6
6P
WHT TO YB BOARD
:S-MICRO
CN201
H.SYNC
≠≠≠≠≠≠
≠≠≠≠≠
≠≠≠≠≠≠
V.SYNC
≠≠≠≠≠
RTS(17A)
NC(18A)
TXD(19B)
+5V(19A)
RXD(18B)
2
1 H.SYNC
2 V.SYNC
3 RTS(OPTION)
GND
4
NC
5
6 TXD(OPTION)
+5V
7
8 RXD(OPTION)
CN7
8P
YEL
:S-MICRO
+5V
TXD(20B)
≠≠≠
≠≠
RXD(21A)
+5V(22A)
+5V
TXD(23A)
≠≠≠
RXD(23B)
≠≠
1
2
3
4
5
6
7
8
9
TO YC BOARD
CN301
GND
TXD
RXD
GND
+5V
GND
TXD
RXD
GND
CN8
9P
WHT
:S-MICRO
3
TO HD BOARD CN102
(14G1/20G1)
TO HC BOARD CN2
(14G5)
+5V
4
TB(MOTHER)
CN1
64P
B TO B
CN5
64P
B TO B
GND
A1
GND
B1
NC
A2
NC
B2
NC
A3
NC
B3
NC
A4
NC
B4
NC
A5
NC
B5
NC
A6
NC
B6
NC
A7
NC
B7
NC
A8
NC
B8
NC
A9
NC
B9
NC
A10
NC
B10
NC
A11
NC
B11
NC
A12
NC
+12V B12
+12V
+12V
A13
≠≠≠≠≠
TALLY
≠≠≠≠
TALLY
B13
≠≠≠≠≠≠≠≠
OVERLOAD
≠≠≠≠≠≠≠
A14 OVERLOAD
STAND
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠
BY
STANDBY
B14
≠≠≠≠≠
POWER
≠≠≠≠
POWER
A15
+5V
+5V
B15
≠≠≠≠≠≠
H.SYNC
≠≠≠≠≠
H.SYNC
A16
≠≠≠≠≠≠
V.SYNC
≠≠≠≠≠
V.SYNC
B16
RTS(17A)
A17 RTS(OPTION)
GND
B17
NC(18A)
NC
A18
RXD(18B)
B18 RXD(OPTION)
+5V(19A)
+5V
A19
TXD(19B)
B19 TXD(OPTION)
GND
A20
≠≠≠
TXD(20B)
≠≠
TXD
B20
RXD(21A)
RXD
A21
GND
B21
+5V(22A)
+5V
A22
GND
B22
TXD(23A)
TXD
A23
≠≠≠
RXD(23B)
≠≠
RXD
B23
GND
A24
NC
B24
NC
A25
NC
B25
NC
A26
NC
B26
NC
A27
NC
B27
NC
A28
NC
B28
NC
A29
NC
B29
NC
A30
NC
B30
NC
A31
NC
B31
GND
A32
GND
B32
TO BC BOARD(4/4)
CN2
+120V
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
VIDEO
PY
PC
Y/G
PB/B
PR/R
CH.SLOT5
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠
CH.SLOT2
≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠
CH.SLOT3
≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠
CH.SLOT1
≠≠≠≠≠≠≠
CHAR.BLK
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠
≠≠≠≠≠≠
CHAR.G
≠≠≠≠≠
≠≠≠≠≠≠
CHAR.B
≠≠≠≠≠
≠≠≠≠≠≠
CHAR.R
≠≠≠≠≠
AFC.PULSE
≠≠
HS
≠
≠≠
VS
≠
≠≠≠
2HS
≠≠
≠≠≠
2VS
≠≠
NC22A
NC22B
NC23A
NC23B
NC24A
V.BLK1
H.BLK
V.BLK2
D.5V SENSE
RESET
SPL PULSE
MISO
MOSI
SCLK
D.5V
D+5V
-2
INT SIG
TB
CN3
64P
B TO B
CN2
64P
B TO B
GND
A1
GND
B1
+B
A2
+B
B2
GND
A3
GND
B3
-15V
A4
-15V
B4
+15V
A5
+15V
B5
-6V
A6
-6V
B6
+6V
A7
+6V
B7
GND
A8
VIDEO
B8
PY OUT
A9
PC OUT
B9
GND
A10
Y/G
B10
GND
A11
PB/B
B11
GND
A12
PR/R
B12
SLOT6
A13
SLOT7
B13
SLOT4
A14
SLOT5
B14
SLOT2
A15
SLOT3
B15
SLOT0
A16
SLOT1
B16
GND
A17
B17 CHAR.BLK
CHAR.G
A18
CHAR.B
B18
CHAR.R
A19
B19 AFC.PULSE
H SYNC
A20
V SYNC
B20
2H SYNC
A21
2V SYNC
B21
NC
A22
NC
B22
NC
A23
NC
B23
NC
A24
V.BLK1
B24
H.BLK
A25
V.BLK2
B25
NC
A26
RESET
B26
S.PULSE
A27
MISO
B27
MOSI
A28
SCLK
B28
A29 DIGITAL+5V
B29 DIGITAL+5V
A30 DIGITAL.GND
B30 DIGITAL.GND
NC
A31
B31
INT SIG
GND
A32
GND
B32
-15V
-15V
+15V
+15V
-6V
-6V
+6V
+6V
VIDEO
PY
PC
Y/G
2Y/2G
PB/B
2PB/2B
PR/R
2PR/2R
CHAR.BLK
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠
≠≠≠≠≠≠
CHAR.G
≠≠≠≠≠
≠≠≠≠≠≠
CHAR.B
≠≠≠≠≠
≠≠≠≠≠≠
CHAR.R
≠≠≠≠≠
AFC.PULSE
≠≠
HS
≠
≠≠
VS
≠
≠≠≠
2HS
≠≠
≠≠≠
2VS
≠≠
NC22A
NC22B
NC23A
NC23B
NC24A
V.BLK1
H.BLK
V.BLK2
D.5V SENSE
RESET
SPL PULSE
MISO
MOSI
SCLK
D.5V
D+5V
-2
CH.SLOT5
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠
INT SIG
TO BC BOARD(4/4)
CN1
A1
GND
B1
GND
A2
GND
B2
GND
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
A8
GND
B8
VIDEO
GND
A9
B9
PY
A10
GND
B10
PC
A11
GND
B11
Y/G
A12
GND
2Y/2G
B12
A13
GND
B13
PB/B
A14
GND
2PB/2B
B14
A15
GND
B15
PR/R
A16
GND
2PR/2R
B16
A17
GND
B17 CHAR.BLK
CHAR.G
A18
CHAR.B
B18
CHAR.R
A19
B19 AFC.PULSE
HS
A20
VS
B20
2HS
A21
2VS
B21
A22
NC22A
B22
NC22B
A23
NC23A
B23
NC23B
A24
NC24A
B24
V.BLK1
A25
H.BLK
B25
V.BLK2
A26 +5V.SENSE
B26
RESET
A27
S.PULSE
B27
MISO
A28
MOSI
B28
SCLK
A29 DIGITAL+5V
B29 DIGITAL+5V
A30 DIGITAL.GND
B30 DIGITAL.GND
A31 CH.SLOT5
B31 INTERNAL.SIG
A32
GND
B32
GND
A1
GND
B1
GND
+120V
A2
+120V
B2
+120V
A3
GND
B3
GND
-15V
A4
-15V
-15V
B4
-15V
+15V
A5
+15V
+15V
B5
+15V
-6V
A6
-6V
-6V
B6
-6V
+6V
A7
+6V
B7
+6V
+6V
DU.G
A8
DU.B
B8
DU.R
A9
VSP
V.SP
B9
ABL
A10
ABL
G2 CONTROL
B10 G2.CONTROL
A11
GND
Y/G
B11
Y/G
A12
GND
2Y/2G
2Y/2G
B12
A13
GND
PB/B
B13
PB/B
A14
GND
2PB/2B
2PB/2B
B14
A15
GND
PR/R
B15
PR/R
A16
GND
2PR/2R
2PR/2R
B16
A17
GND
≠≠≠≠≠≠≠≠
CHAR.BLK
≠≠≠≠≠≠≠
B17 CHAR.BLK
≠≠≠≠≠≠
CHAR.G
≠≠≠≠≠
CHAR.G
A18
≠≠≠≠≠≠
CHAR.B
≠≠≠≠≠
CHAR.B
B18
≠≠≠≠≠≠
CHAR.R
≠≠≠≠≠
CHAR.R
A19
AFC.PULSE
B19 AFC.PULSE
≠≠
HS
≠
HS
A20
≠≠
VS
≠
VS
B20
≠≠≠
2HS
≠≠
2HS
A21
≠≠≠
2VS
≠≠
2VS
B21
NC22A
NC
A22
NC22B
NC
B22
NC23A
NC
A23
NC23B
NC
B23
NC24A
H PULSE
A24
V.BLK1
B24
V.BLK1
H.BLK
A25
H.BLK
V.BLK2
B25
V.BLK2
D.5V SENSE
A26 +5V.SENSE
RESET
B26
RESET
SPL PULSE
A27
S.PULSE
MISO
B27
MISO
MOSI
A28
MOSI
SCLK
B28
SCLK
D.5V
A29 DIGITAL+5V
B29 DIGITAL+5V
D+5V
A30 DIGITAL.GND
-2
B30 DIGITAL.GND
≠≠≠≠≠≠≠≠
CH.SLOT3
≠≠≠≠≠≠≠
A31 CH.SLOT3
INT SIG
B31 INTERNAL.SIG
A32
GND
B32
GND
TO BK BOARD(9/9)
CN1
+120V
TO OPTION BOARD
5
CN4
50P
+120V
+120V
-15V
-15V
+15V
+15V
-6V
C102
1000
10V
:HT
L102
22µH
-6V
+6V
+6V
C101
1000
10V
:HT
L101
22µH
VSP
ABL
G2 CONTROL
AFC.PULSE
≠≠
HS
≠
≠≠
VS
≠
≠≠≠
2HS
≠≠
≠≠≠
2VS
≠≠
NC22A
NC22B
NC23A
NC23B
NC24A
V.BLK1
H.BLK
V.BLK2
D.5V SENSE
RESET
MISO
MOSI
D.5V
D+5V
-2
CH.SLOT2
≠≠≠≠≠≠≠≠
≠≠≠≠≠≠≠
≠≠≠≠≠≠≠≠
CH.SLOT1
≠≠≠≠≠≠≠
SCLK
INT SIG
A1
GND
B1
GND
A2
+120V
B2
+120V
A3
GND
B3
GND
A4
-15V
B4
-15V
A5
+15V
B5
+15V
A6
-6V
B6
-6V
A7
+6V
B7
+6V
DU.G
A8
DU.B
B8
DU.R
A9
V.SP
B9
A10 ABL OUT
B10 G2.CONTROL
A11 AFC.PULSE
HS
B11
VS
A12
2HS
B12
2VS
A13
NC22A
B13
NC22B
A14
NC23A
B14
NC23B
A15
NC24A
B15
V.BLK1
A16
H.BLK
B16
V.BLK2
A17
B17 +5V.SENSE
RESET
A18
NC27A
B18
MISO
A19
MOSI
B19
A20 DIGITAL+5V
B20 DIGITAL+5V
A21 DIGITAL+5V
B21 DIGITAL+5V
A22 DIGITAL.GND
B22 DIGITAL.GND
A23 DIGITAL.GND
B23 DIGITAL.GND
A24 CH.SLOT2
B24 CH.SLOT1
A25
SCLK
B25 INTERNAL.SIG
TO TA BOARD
CN14
B-SS3280<AEP>-TB.
11-54
A
B
C
D
11-54
E
F
G
H
The material contained in this manual consists of information
that is the proterty of Sony Corporation and is intended solely
for use by the purchasers of the equipment described in this
manual.
Sony Corporation expressly prohibits the duplication of any
portion of this manual or the use there of for any purpose other
than the poeration or maintenance of the equipment described
in this manual without the express written permission of Sony
Corporation.
Le matériel contenu dans ce manuel consiste en informations
qui sont la propriété de Sony Corporation et sont destinées
exclusivement à l’usage des acquéreurs de l’équipement
décrit dans ce manuel.
Sony Corporation interdit formellement la copie de quelque
partie que ce soit de ce manuel ou son emploi pour tout autre
but que des opérations ou entretiens de l’équipement à moins
d’une permission écrite de Sony Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind, und
ausschließlich zum Gebrauch durch den Käufer der in dieser
Anleitung beschriebenen Ausrüstung bestimmt sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als die
Bedienung oder Wartung der in dieser Anleitung beschriebenen
Ausrüstung ohne ausdrückliche schriftliche Erlaubnis der
Sony Corporation.
English
98BT0911-1
Sony Corporation
9-922-695-01
Printed in Japan
©1998.2
Broardcasting & Professional Systems Company
Published by Global Support Promotion Dept.