Download Denver CAD-391 Instruction manual
Transcript
CAD-391 PTY AF 3 2 1 15 13 12 TA 7 16 10 INSTRUCTION MANUAL PTY CAR STEREO CD/CDR/CDRW/MP3/WMA PLAYER WITH PLL FM STEREO RADIO 8 19 20 21 22 23 24 14 5 6 11 9 25 RDS 4 (1-6) BLUETOOTH FUNCTION IN MOBILE PHONE WIRELESS BLUETOOTH HEADSET FLIP DOWN/DETACHABLE FRONT PANEL AF RESET TA LOCATION OF PARTS AND CONTROLS 3 2 1 15 13 12 7 16 10 PTY AF 8 19 20 21 22 23 4 (1-6) 24 14 5 TA 6 11 9 1 25 PTY 2 3 AF ENTER 9 TA POWER 1. POWER ON/OFF ( ) SEL VOL 11 2. FUNCTION SELECT BUTTON: BASS/TREBLE/BALANCE/ FADER / TA SEEK/MASK DPI/RETUNE/AUDIO DSP/LOUDVOL NESS/ESP/CD MULTI/BEEP/SEEK/STEREO/LOCAL 3 2 1 15 13 BAND 12 7 16 10 10 3. VOL UP/VOL DOWN FOR BASS/TREBLE/BALANCE/ MP3 FADER / TA SEEK/MASK DPI/RETUNE/AUDIO DSP/LOUDAS/PS 1 2 3 NESS/ESP/CD MULTI/BEEP/SEEK/STEREO/LOCAL 4 5 6 4. PRESET STATIONS (1,2,3,4,5,6) 5. ‘AF’ function (ALTERNATIVE FREQUENCIES) 6. ‘TA’ function (TRAFFIC ANNOUNCEMENT) 7. ‘PTY’ function (PROGRAM TYPE) 3 2 1 8. DISPLAY BUTTON (DISP)27 26 9. MODE BUTTON (MODE) 8 21 22 23 24 14 5 6 11 9 25 18 19 20 17 10.BAND BUTTON (BND) 19 20 23 21 8 4 (1-6) 11.AUTOMATIC OR MANUAL TUNING 22 4 24 12 (FREQ UP OR FREQ DOWN )/ (1-6) CD TRACK/SEARCH BUTTON 12.AUTO SEEK SEARCH TUNING (A/PS) 13.‘SCAN’ AUTOMATIC TUNING CONTROL (SCN) 14.MUTE BUTTON (MUTE) 15.LCD DISPLAY 8 19 20 16.PANEL RELEASE BUTTON ( ) 17.CD SLOT 26 27 18.CD EJECT BUTTON ( ) 19.PAUSE BUTTON 18 17 20.INTRO BUTTON (Preview all Tracks) 21.REPEAT BUTTON 22.RANDOM BUTTON 23, 24. + 10 TRACK SEARCH DOWN/UP 25.PORTABLE WIRELESS BLUETOOTH HEADSET 26. RESET BUTTON 27. POWER INDICATOR LED MODE TUNE/SEEK DISP PAUSE INT RPT PTY RDM RESET AF TA RESET RESET E 26 27 15 21 22 4 (1 ISO CONNECTOR RCA Jack Line Out: Red (right) White (left) RCA Jack Line In: Red (right) White (left) CONNECTOR A 1. 2. 3. 4. MEMORY +12V 5. AUTO ANTENNA OUTPUT 6. 7. +12V (TO IGNITION KEY) 8. GROUND Note: (connector A no. 7) must be connected by car ignition key in battery becomes weak when the car will be not used for long period. A B 2 1 2 1 4 3 4 3 6 5 6 5 8 7 8 7 order to avoid that car CONNECTOR B 1. REAR RIGHT SPEAKER (+) 2. REAR RIGHT SPEAKER (-) 3. FRONT RIGHT SPEAKER (+) 4. FRONT RIGHT SPEAKER (-) 5. FRONT LEFT SPEAKER (+) 6. FRONT LEFT SPEAKER (-) 7. REAR LEFT SPEAKER (+) 8. REAR LEFT SPEAKER (-) Maintenance FUSE REPLACEMENT If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after the replacement, there may be an internal malfunction. In this case, consult your nearest repairing center. Warning Use the specified amperage fuse for each lead. Use of a higher amperage fuse may cause serious damage. INSTALLATION PRECAUTIONS • Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. • Use only the supplied mounting hardware for a safe and secure installation. • Be sure to remove the front panel before installing the unit. 182mm NOTE : Inclination angle for car radio installation must not 53mm exceed 30˚ otherwise the front panel will not open. screw and 11 release bracket 3 2 3 182mm 4 53mm 2 Bend these claws, if necessary Note: Keep the release key in a safe place as you may need it in future to remove the unit from the car. E TO SUPPORT THE UNIT 3 Dashboard 1. UNIT 2. RELEASE CASE 3. DASH BOARD 4. HEX NUT 5. LOCK WASHER 6. PLAIN WASHER 7. CAR BODY 8. REAR SUPPORT STRAP 9. TAPPING SCREW 10.M5 X 15 HEX BOLT 4 4 6 5 8 2 10 7 5 1 9 4 6 Detaching and attaching the front panel The front panel of this unit can be detached in order to prevent the unit from being stolen. FOLDING DOWN AND DETACHING/ATTACHING THE FRONT PANEL Before detaching the front panel, be sure to press the button (1) OFF first. Then press the button (16), let the Front Panel arrive in horizontal position and detach the panel by pulling it towards you as illustrated. <10° 1 2 Notes: • Do not press the front panel hard against the unit when attaching it. It can be easily attached by pressing it lightly against the unit. • When you carry the front panel with you, put it in the supplied front panel case. • Do not press hard or give excessive pressure to the display window of the front panel when attaching it to the unit. E 1. POWER ON/OFF ( ) By pressing this key, the unit is on or off. This unit is turned on by pressing any key. 2,3.FUNCTION SELECT BUTTON: BASS/TREBLE/BALANCE/FADER / TA SEEK/MASK DPI/RETUNE/AUDIO DSP/LOUDNESS/ESP/CD MULTI/BEEP/SEEK/STEREO/LOCAL (SEL) Turning the VOL knob Right or Left (3), you can adjust VOL/BASS/TREB/BAL/FAD. To select other functions, press the VOL (3) knob shortly until the desired functions is shown on the display. Figure 1 shows how control functions are selected using the VOL knob. 2 1 2 3 4 2 5 2 2 6 Fig. 1 Selection of sound control functions 1. VOL Turning the VOL knob Right or Left. Increase or decrease the volume by turning buttons can be used to adjust the BASS, TREBLE, BALANCE and FADER. TA SEEK/TA ALARM (2) When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function. TA SEEK Mode or TA ALARM mode is selected by VOL VOLorVOL VOL . 2 sec. SEL 2. SEL 3. BAS TA SEEK VOL 4. TRE 5. BAL 6. FAD or VOL VOL VOL VOL . These TA SEEK / TA ALARM - TA SEEK mode: 2 sec. When newly turned station does not receive TP information for 5 sec., the radio retunes to next station which VOL TA SEEK MASK DPI MASK DPI / MASK ALL SEL SEL has not the same station (PI) as the last station, but has the TP information. In TA seek mode, the current station can be changed to the completely different station because the unit 2 sec. searches TP station when the field strength of the current station is very weak, or the current station has no VOL MASK DPI RETUNE RETUNE L / RETUNE S SEL SEL TPSEL signal.TA SEEK - TA ALARM mode: Any automatic retune mode is not activated, just can hear Beep sound. VOL TA(2) SEEK MASK/ DPI DSP ON SEL DPI SEL TA SEEK SEL RETUNE SEL TA SEEK TA ALARM SEL MASK When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function. sec. 22sec. 2 VOL sec. SEL POP M --- ROCK M --- CLASS M --- FLAT M --- DSP OFF VOL TA SEEK MASK DPI MASK DPI / MASK ALL SEL 2 sec. DPI: masked only the AF which has different PI. MASK sec. 22sec. TA masked SEEK MASK DPI SEL ALL: SEL SEL signal SEL strength. RETUNE DSP SEL LOUD MASK the which has different PI and NO RDS with field VOL AF VOL TASEEK SEEK TAMASK SEEK DPI / TA ALARM SEL TA RETUNE RETUNE L / RETUNE S SEL SEL SEL 2 sec. RETUNE L / S CONTROLS (2) 2 sec. 2 sec. press TA SEEK TA SEEK / TA ALARM SEL When the SELVOL button for more 2 seconds, it is TA SEEK MASK DPI thanSEL SEL RETUNE 2SEL sec. activated as mode.SEL SEL DSPselecting LOUD SEL Retune VOL TA SEEK MASK DPI MASKofDPI / MASK ALL SEL SEL RETUNE L: Select 90 seconds asDPI the initial automatic TA search. TA SEEK MASK DSP ON SEL SEL SEL timeRETUNE 2SEL sec. RETUNE S: Select 30 seconds as initial time. 2 sec. VOL 22sec. sec. 2 sec. SEL SEL 2 sec. SEL TA TASEEK SEEK TA SEEK SEL SEL SEL MASK MASKDPI DPI MASK DPI DPI / MASKVOL ALL SELRETUNE RETUNE DSPL / RETUNE SELMASK SEL S LOUD RETUNE SEL VOL SEL VOL CD MULTI ON/OFF MULTI TA SEEK MASK DPI RETUNE SEL SEL TA SEEK MASK DPI SEL RETUNE SEL POP M --ROCK M ----- FLATSEL M --- DSP OFF TA SEEK MASKMDPI SEL CLASS RETUNE SEL ESP RETUNE L / RETUNE S DSP ON SEL SEL DSP SEL VOL TA SEEK MASK DPI SEL SEL RETUNE DSP SEL SEL M --- ROCKSEL M --- CLASS --- FLATSEL M --- DSPRETUNE OFF 2VOL sec. POP TA SEEK MASKMDPI DSP ON SEL SEL ESP12 / ESP 45 TA SEEK MASK DPI SEL SEL SEL SEL RETUNE DSP SEL VOL ON/OFF SEL SEL MULTI BEEP 2 sec. POP M --- ROCK M --- CLASS M --- FLAT M --- DSP OFF 2VOL sec. LOUDNESS CONTROLS TA SEEK MASK DPI SEL SEL (2) SEL SEL RETUNE DSP SEL 2 sec. TA SEEK MASK DPI SEL SEL for SEL as selecting RETUNE DSP SEL 2 sec. press When SEL button more than 2SEL seconds, it is activated mode TAthe SEEK MASK DPI SEL SEL SEL RETUNE DSP SEL SEL 2SEL sec. TA SEEK MASK DPI SEL SEL RETUNE DSP SEL SEL 2 sec. TA SEEK VOLSELCD MULTI MASKON/OFF DPI SEL SEL SEL RETUNE DSP SEL SEL MULTI TA SEEK MASK DPI SEL SEL SEL RETUNE DSP SEL SEL VOL ESP12 / ESP 45 VOL SEL MULTI BEEP SEEK SEEK1 / SEEK 2 SEL SEL VOL VOL VOL VOL 2SEL sec. VOL ESP 2 sec. DSP CONTROLS (2) AUDIO VOL TA SEEK MASK DPI SEL SEL SEL SEL RETUNE DSP SEL LOUD ON/OFF TA SEEK MASK DPI thanSEL DSP ON SEL SEL RETUNE When the SEL button for more 2 seconds, it is activated as selecting mode of these function. 2 SEL sec. press SEL VOL SEL 2 sec. ON/OFF VOL TA SEEK / TA ALARM SEL / ESP 45 SEL TA SEEK VOL 2 sec. ESP12 TA SEEK MASK DPI MASK DPI / MASK ALL SEL VOL VOL --- ROCK SEL M --- CLASS M --M --- DSPRETUNE OFF TAMSEEK MASK DPIFLAT SEL RETUNE L / RETUNE S SEL POP 2 sec. SEL 2 sec. VOL LOUD 2 sec. ON/OFF mode is selected by 2 sec. / ESP 45 SEL 2VOL sec. ESP12 TA SEL TA SEEK SEEK SEL SEL TA SEEK SEL 2SEL sec. 2SEL sec. MASK MASK DPI DPI MASK DPI or SEL SEL SEL MULTI MULTI TA TA SEEK SEEK BEEP SEEK SEL SEL SEL CD MULTI ON/OFF SEL MASK SEL RETUNE MASK DPI DPI SEL RETUNE SEL VOL LOUD SEL SEL VOL ESP ESP ON/OFF LOUD ON/OFF ESP SEL LOUD of these function. LOUD ESP SEL VOL LOUD LOUD LOUD SEL VOL SEL ESP ON/OFF ESP . The bass and treble response will be boosted. RETUNE RETUNE RETUNE TA SEEK MASK DPI RETUNE SEL VOL / ESP 45 SEL BEEP ON/OFFRETUNE SEL ESP12 MULTI TA SEEK SEL MASK DPIVOL SEL SEL E VOL CD MULTI ON/OFF SEL MULTI 22SEL sec. sec. SEL SEL 2 sec. SEL LOUD LOUD SEL SEL SEL SEL SEL DSP DSP DSP SEL SEL SEL DSP DSP STEREO SEL DSP SEL DSP SEL SEL VOL LOUD LOUD LOUD LOUD LOUD SEL SEL SEL SEL SEL STEREO/MONO SEL SEL LOUD SEL SEL LOUD ESP ESP ESP ESP ESP ESP ESP 2SEL sec. 2VOL sec. SEL SEL VOL POP M --- ROCK M --- CLASS M --- FLAT M --- DSP OFF 2 2sec. 2 sec. sec.MODE (2) ESP VOL 2SEL sec. VOL TA DPI SEL SEL RETUNE SELor 45 RETUNE DSP SEL ON/OFF VOL TASEEK SEEK SEEK /DPI TA ALARM MASK RETUNE L / sec. RETUNE S LOUD SEL TAMASK SEL When press the SELSEL button for more than 2 seconds, it is activated as 12 sec. of ESP mode can TA SEEK MASK DPI DSP ON SEL SEL SEL RETUNE SEL be2 sec. selected. 2 2SEL sec. sec. 22sec. sec. VOL SEL SEL SEL 2SEL sec. TA SEEK SEL MASK DPI SEL RETUNE SEL VOL TA SEEK MASK RETUNE POP --- ROCKSEL M --- CLASS MDPI --FLATSEL M --- DSP OFF TAM SEEK MASK DPI MASK DPI / MASKSEL ALL SEL VOL TA TASEEK SEEK MASK/ TA DPIALARM SEL TA SEEK SEL RETUNE SEL SEL DSP DSP SEL DSP ON LOUD LOUD ON/OFF VOL ESP SEL TA SEEK MASK DPI SEL SEL RETUNE DSP LOUD SEL SEL ESP12 / ESP 45 VOL TASEEK SEEK MASK DPI RETUNE RETUNE L / RETUNE S LOUD SEL SEL POP M --- ROCKSEL M --- CLASS MDPI --- FLAT M --- DSP OFF TA MASK SEL SEL RETUNE DSP SEL VOL TA SEEK MASK DPI MASK DPI / MASK ALL SEL VOL ESP12 / ESP 45 MODE (2) 2 sec. MULTI CD SECTION 2SEL sec. 22VOL sec. sec. TAMSEEK MASK DPI DSP ON SEL SEL RETUNE SEL POP --- ROCK M --- CLASS M --FLAT VOL M --- DSP OFF VOLALL TASEEK SEEK MASKDPI DPI DPI / MASK SEL TA MASK RETUNE RETUNE L / RETUNE S SEL SEL MASK ESP SEL VOL SEL SEL SEL ON/OFF VOL sec. 222sec. TA SEEK MASK DPIthan SEL ESP SEL SEL SEL as DSP RETUNE SEL When the SEL button for more 2 seconds, it is activated selectingSEL modeLOUD of these function. 2sec. sec. press SEL 2SEL sec. SEL SEL SEL SEL 2 sec. VOL 2 VOL sec. SEL TA MASK TASEEK SEEK MASKDPI DPI SEL SEL RETUNE RETUNE SEL SEL TA SEEK MASK DPI RETUNE SEL SEL TA SEEK MASK DPI SEL RETUNE SEL TA SEEK MASK DPI SEL RETUNE SEL VOL CD MULTI ON/OFF MULTI ESP12 / ESP 45 POP M --- ROCK M --- CLASS M --- FLAT M --- DSP OFF TA SEEK VOL SELCD MULTI MASK DPI RETUNE SEL MULTI TA SEEK MASKON/OFF DPI SEL RETUNE SEL SEL SELRETUNE DSP SEL S LOUD DSP SEL LOUD / RETUNE DSPL ON SEL SEL DSP SEL LOUD ESP ON/OFF ESP VOL SEL SEL VOL SEL DSP LOUD SEL ESP SEL DSP ON SEL ESP SEL RETUNE DSP SEL SEL SEL LOUD VOL VOLorVOL VOL . CD MULTI ON: Read multi section CD. CD by ESP SEL RETUNE DSP SEL SELVOL SEL LOUD VOL TAMSEEK MASK DPIFLAT M SEL SEL SEL SEL DSP SEL LOUD ON/OFF POP --- ROCK M --CLASS M ----- DSPRETUNE OFF MULTI Read first section only. TA SEEK MASK DPI ESP SEL OFF: SEL SEL RETUNE DSP SEL SEL SEL LOUD VOL ON/OFF SEL SEL MULTI BEEP 2 sec. CD MULTI ON/OFF SEL MULTI (2) VOL 2 sec. BEEP MODE 2 sec. VOL TA the SEEK MASK DPI SEL SEL for SEL as selecting RETUNE DSP SEL SELSEL ESP SEL LOUD ON/OFFRETUNE SEL MULTI BEEP When SELSEL button more than 2SEL seconds, it is activated mode of these function. TA SEEK MASK DPI SEL SEL SEL DSP LOUD SEL SEL ESP VOL 2SEL sec. press TA SEEK MASK DPI SEL SEL SEL RETUNE DSP LOUD ON/OFF 2 sec. TA SEEK MASK DPI ESP SEL SEL SEL RETUNE DSP SEL SEL SEL LOUD 2 sec. VOL TA SEEK MASKON/OFF DPI ESP SEL SEL CD MULTI SEL RETUNE DSP SEL SEL SEL LOUD MULTI VOL 2SEL sec. / ESP 45 SEL TA SEEK MASK DPI ESP SEL ESP12 SEL RETUNE DSP SEL SEL SEL LOUD TA SEEK MASK DPI SEL SEL SEL RETUNE DSP LOUD SEL SEL ESP SEL VOL SEL MULTI BEEP SEEK SEEK1 / SEEK 2 SEL SEL VOL 2 sec. ON/OFF SEL SEL MULTI BEEP 2 sec. VOL MULTI BEEP TA SEEK MASK DPI DPI SEL SEL ESP SEL SEL SEL / SEEK SEEK1 SEL RETUNE DSP2 SEL SEEK SEL SEL LOUD TA SEEK MASK ESP SEL SEL SEL RETUNE DSP SEL SEL LOUD VOL ESP12 / ESP 45 BEEP ON: BEEP sound can be heard from speaker when the buttons are pressed. VOL ON/OFF SEL SEL CD MULTI MULTI(2) VOL BEEP ON/OFF 22SEL sec. sec. MODE SEEK MULTI TA MASK DPI ESP SEL SEL SEL RETUNE DSP SEL SEL TASEEK SEEK MASK DPI ESP SEL press SEL for SEL as selecting RETUNE DSP SEL When the SEL button more than 2SEL seconds, it is activated mode LOUD of these function. SEL SEL LOUD SEL 2SEL sec. 2 sec. TA SEEK MASK DPI SEL SEL 2 sec. CD MULTI mode is selected 2VOL sec. TA ON/OFF SEEK MASK DPI SEL ESP12 / ESP 45 SEL 22 sec. sec. SEL TA SEEK 2 sec. SEL 2 sec. SEL SEL SEL SEL MULTI TA SEEK SEEK TA MULTI MULTI SEL MASK DPI SEL RETUNE DSP SEL SEL SEL SEL LOUD LOUD ESP ESP VOL BEEP STEREO SEEK SEL SEL SEL SEEK1 STEREO/MONO / SEEK 2 VOL MASK DPI DPI SEL SEL RETUNE DSP SEL SEL SEL LOUD MASK SEL SEL RETUNE DSP SEL SEL LOUD VOL SEL CD MULTI ON/OFF BEEP STEREO SEEK SEL SEL SEL STEREO/MONO ESP ESP VOL 22 sec. sec. SEL 2SEL sec. SEL 2 sec. SEL MULTI BEEP DPI VOL SEEK SEEK1 SEL SELSEL TA SEEK MASK ESP SEL SEL / SEEK RETUNE DSP 2 SEL SEL LOUD ON/OFF SEL ESP MULTI BEEP TA SEEK MASK DPI ESP SEL SEL SEL RETUNE DSP SEL SEL SEL LOUD TA SEEKSEEK MASK DPI SEL 1: When SEL SEL is stopped RETUNE DSP SELAUTO SEL station LOUD is SEL SEEK 1 mode is activated, SEEK SCAN when detectedESP even 2 sec. VOL VOL SEL MULTI SEEK BEEP LOCAL LOCAL/DX SEL STEREO/MONO STEREO SEEK SEL SEL SEL 2 sec.still push user button. VOL TA SEEK MASK DPI ESP SEL SEL SEL RETUNE DSP SEL SEL SEL LOUD ON/OFF SEL SEL MULTI SEEK 2: Auto SEEK SCAN isMASK not stopped even station user push SEEK button. When release TA SEEK DPI ESP SEL SEL BEEP SEL if DSP RETUNEis detected SEL SEL LOUD VOL SEL MULTI BEEP LOCAL/DX SELSEL LOCAL STEREO SEEK SEL SEL SEL VOL this SEEK button, then stop when station is detected. 22 sec. sec. SEL MULTI SEL BEEP SEL SEEK VOL SEEK1 / SEEK 2 SEL MULTI BEEP STEREO SEL SEL TA SEEK MASK ESP SEL SEL RETUNE DSP SEL SELSTEREO/MONO LOUD TA SEEK (2)SEL MASK DPI DPI SELSEL ESP SEL SEL SEL RETUNE DSP SEL SEEK SEL SEL LOUD STEREO/MONO When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function. 2 sec. SEL 2 sec. SEL SEL SEL MULTI MULTI TA SEEK TA SEEK SEL SEL SEL SEL 2 sec. SEL SEL SEL MULTI MULTI TA SEEK SEL SEL SEL BEEP SEEK SEL SEL BEEP SEL MASK DPI SELSEL SEEK RETUNE SEL 2 sec. MULTI SEL BEEP 2 sec. SEL SEL MULTI TA SEEK SEL SEL BEEP SEEK SEL SEL MASK DPI RETUNE SEL SEL MULTI SEL BEEP VOL VOL BEEP LOCAL STEREO SEEK SEL SEL SEEK1 BEEP SEEK / SEEK 2 SEL SEL MASK DPI SEL RETUNE DSP SEL SEL LOUD MASK DPI SEL RETUNE DSP SEL SEL LOUD STEREO STEREO SEL DSP VOL LOCAL/DX ESP SEL ESP SEL STEREO/MONOVOL SELSEL LOCAL ESP SEL LOCAL/DX LOUD VOL When FM stations are weak and are disturbed, listening can be improved by selecting MONO. TA (2) SEEK MASK DPI SEL SEL SEL RETUNE DSP SEL SEL SEL LOUD LOCAL/DX When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function. SEL SEL SEEK SEL SEEK SEL STEREO STEREO SEL DSP STEREO VOL STEREO/MONO LOCAL SEL SEL LOUD SEL LOCAL VOL SEL VOL ESP LOCAL/DX ESP LOCAL/DX “Local” position in areas with strong signals to let radio stop at only strong stations during manual tuning (LOC appears). Select Distant position in areas with weak signals to listen to all stations. 4. PRESET STATIONS (1,2,3,4,5,6) (A) RADIO MODE: When pressed shortly, these keys select a preset station directly. When pressed longer than 1 sec., current station is stored in preset memory bank. When PTY mode is selected, the PTY switch is shared as follows: PTY music group ---- PTY speech group ---- OFF E MUSIC 1. POP M, ROCK M 2. EASY M, LIGHT M 3. CLASSICS, OTHER M 4. JAZZ, COUNTRY 5. NATION M, OLDIES 6. FOLK M (B) CD/MP3/WMA PLAYER MODE: 1. PAUSE 2. INT 3. RPT 4. RDM SPEECH 1. NEWS, AFFAIRS, INFO 2. SPORT, EDUCATE, DRAMA 3. CULTURE, SCIENCE, VARIED 4. WEATHER, FINANCE, CHILDREN 5. SOCIAL, RELIGION, PHONE IN 6. TRAVEL, LEISURE, DOCUMENT USING THE RDS FUNCTION What is RDS? The RDS (Radio Data System) is a digital information system developed by the EBU (European Broadcast Union). Piggy-backed on normal FM broadcasts, RDS offers a variety of information services and automatic retuning functions for RDS-compatible car stereos. In 1988, RDS became available in the United Kingdom, France, West Germany, Ireland and Sweden. Test transmissions are being conducted in many other European countries. It is expected that RDS will be available in most Western European countries in the near future. 5. ‘AF/REG’ function (ALTERNATIVE FREQUENCIES) When pressed shortly, AF/REG switching mode is selected. When AF/REG switching mode is selected, the radio checks the signal strength of the AF all the time. When pressed long, it is activated as regional mode ON/OFF. – Regional mode ON: AF switching or PI SEEK is implemented to the station which have all PI codes same as current station. REG segment is turned on, in LCD display. – Regional mode OFF The regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented. 6. ‘TA’ function (TRAFFIC ANNOUNCEMENT) When pressed shortly, it is activated as TA mode on or off When TA mode is on and traffic announcement is transmitted – When the unit is in CD/MP3 mode, it will switch to radio mode temporarily. – If the volume level was under the threshold point, it will be raised to the threshold point. – When TP station is received, TP segment is turned on in LCD display. 7. ‘PTY’ function (PROGRAM TYPE) PTY MUSIC ---- PTY SPEECH ---- PTY OFF While selecting PTY type, its selection is implemented by preset buttons as described in preset key. When PTY is selected, the radio starts to search corresponding PTY information, and stops if the corresponding PTY information is detected. 8. DISPLAY (DISP) Press DISP button to switch between display informations such as radio frequencies, clock, track and other informations depending on the playing MODE. 9. MODE BUTTON (MODE) By pressing this key, user can select. AUX/TUNER/CD-MP3 or BT mode. 10. BAND BUTTON (BND) Each band is toggled cyclically by pressing this key FM1---FM2---FM3. 11. AUTOMATIC OR MANUAL TUNING (FREQ UP OR FREQ DOWN ) (A) RADIO MODE When pressed shortly, these keys are operated as MANUAL tuning mode. When pressed longer than 1 sec., they are operated as SEEK tuning mode. (B) CD/MP3/WMA PLAYER MODE When pressed shortly, they are operated as TRACK UP or TRACK DOWN mode. When pressed longer than 1 sec., they are operated as CUE or REVIEW mode. 12. AUTO SEEK SEARCH TUNING (A/PS) By pressing shortly, the radio searches for each preset station. When field strength level is bigger than the threshold level of stop level, the radio is holding at that preset number for 5 sec. with releasing mute, and then searches again. By pressing longer than 1 sec, and then 6 strongest stations are preset to the corresponding preset number. When AS operation is finished, the radio executes the preset scan. 13. ‘SCAN’ AUTOMATIC TUNING CONTROL (SCN) This key is operated as RADIO SCAN. The operation is similar as normal search but different thing is holding 5 seconds on every station detected in RADIO SCAN mode. E 14. MUTE BUTTON (MUTE) Press this button, audio will disappear. Press this button again in order to hear audio newly. 15. LCD DISPLAY The Liquid Crystal Display will display the current state of the unit. 16. OPEN THE FRONT PANEL Press ( ) button and the front panel will open. CD/MP3/WMA CONTROL LOCATION OF PARTS TRACK/SEARCH BUTTON (11) FORWARD AND REVERSE TRACK SEARCH (or changing songs) Press the SKIP button ( or ) during play to go to the desired track(song). ....REVERSE ....FORWARD Press and hold the SKIP button ( or ) during play to scan the disc at high speed. When the desired music section of the disc is found, release the button. Normal play will resume. 17. CD SLOT 18. CD EJECT BUTTON Press the button to remove the CD. 19. PAUSE BUTTON During “PLAY”, press (19) ‘PAU’ button to “PAUSE”. Press it again to resume play. 20. INTRO BUTTON (Preview all Tracks) When this button is pressed, ‘INT ON’ indication is displayed and the first several seconds of each track of the disc are played. Press again to stop intro and listen to track. 21. REPEAT BUTTON When this button is pressed, ‘RPT ON’ indication is displayed and play of the selected track will be continually repeated until the Track repeat mode is cancelled by pressing ‘RPT’ button again. 22. RANDOM BUTTON When this button is pressed, ‘RDM ON’ indication is displayed and each track of the disc are played in random instead of normal progression. To cancel RANDOM mode, press ‘RDM’ button (21) again. 23, 24. 10 TRACK UP/DOWN SELECT: (In case of MP3/WMA files) M5: 10 Track down / M6: 10 Track up HOW TO SELECT MP3/WMA FILES 1. 2. 3. Searching Track: • Press “A/PS”, then searching track is activated. • Press “VOL” knob, then the first digit is blinking. • With “VOL select first digit you want. VOL VOL / VOL VOL ” knob, VOL • Press “VOL” knob, then the first digit is fixed and second digit is blinking. • With “VOL select 2’nd 3’rd respectively. VOL VOL / VOL VOL ” knob, VOL • Then automatically the song you selected will start. Searching File Name: • Press “A/PS” twice, then file search is activated. • Press “VOL” knob, then the first directory is displayed. • With “VOL you can select the directory you want. VOL VOL / VOL VOL ” knob, VOL • Press “VOL” knob again, then the directory is fixed and the first file name is displayed. • With “VOL you can select the file you want. VOL VOL / VOL VOL ” knob, VOL • Press “VOL” knob, then the song you selected will start. Searching Character: • Press “A/PS” 3 times, then character search mode is activated. • Press “VOL” knob, then “A” character is displayed. • With “VOL you can select the letter you want. VOL VOL / VOL VOL ” knob, VOL • Press “VOL” knob longer than 2 sec. • The song which has same character you selected is displayed. • With “VOL you can select the song you want. VOL VOL / VOL VOL ” knob, VOL • Press “VOL” knob, then the song you selected will start. E 25. WIRELESS BLUETOOTH HEADSET HOW TO USE BLUETOOTH IN YOUR CAR AUDIO 3 1 4 1. RELEASE BLUETOOTH HANDSET 2. 3. 4. 5 6. 7. ANSWER / MAKE A CALL VOLUME + VOLUME LED LIGHT MICROPHONE EAR CLIP Before you can use the Bluetooth headset, you must first perform PAIRING. Pairing is a procedure used to connect 2 Bluetooth devices together. 1. Press and hold button until Red and Blue LED blinks alternately. 7 5 6 2 This is Pairing mode stage. 2. Turn on the Bluetooth connection of the mobile phone. Perform Add Bluetooth device. The mobile will search for any Bluetooth devices within the range. Select “BT” and enter Passkey: “0000” to connect to the car audio. (Please refer to the instruction manual of your mobile phone for Bluetooth Pairing. Your mobile phone should have Bluetooth function otherwise can not do the pairing). 3. After successful pairing, headset’s Blue LED will blink once every 3 seconds. This unit is in active mode. 4. When there’s incoming call, simply press button to receive call. 5. When talking, you can adjust headset’s volume level by pressing +/- button found at the upper left / right side of headset. 6. Press button once to end call. 7. To make calls, dial from your mobile phone. Sound automatically transfer to headset. Note: • To turn on headset, press and hold until Blue LED lights on. When no device connection was found, Blue LED will blink once every 10 seconds. • To turn off headset, press and hold until LED lights are off. • Press 2x continously will dial the last number. • “Last Number Redial” will store the last number dialled out from the mobile phone. CHARGING THE BLUETOOTH HEADSET When Bluetooth headset battery state is low or out of power, attach it back to the front panel and head unit will charge it automatically. During charging, red LED lights on all the time. When fully charge, Red LED 3 2 1 disappears. Note: When charging, it is advisable to let it be fully charge before detaching it from front panel for use. 15 Here is a listing of current Bluetooth Mobile phones: Nokia 3230 Nokia 3250 Nokia 5200 Nokia 5300 Nokia 6021 Nokia 6103 Nokia 6230 Nokia 6233 Nokia 6280 Nokia 6311 Nokia 6600 Nokia 6670 Nokia 6680 Nokia 7610 Nokia 8800 Nokia E50 Nokia E60 Nokia E61 Nokia E70 Nokia N70 Nokia N71 Nokia N72 Nokia N90 Nokia N91 Samsung D508 Samsung D608 Samsung D800 Samsung D908 Samsung E370 Samsung E648 Samsung E870 Samsung E900 Samsung P300 Samsung Z400 Samsung Z510 26. RESET Reset button is placed on the housing. The reset button is to be activated for the following reason: • Initial installation of the unit when all wiring is completed. • All the function button do not operate. • Error symbol on the display. 27. POWER INDICATOR LED Flash LED when ignition is switched on. E Sony Ericsson 810C Sony Ericsson K750i Sony Ericsson K800i Sony Ericsson T610 Sony Ericsson W810i Sony Ericsson Z550C Sony Ericsson Z710i Motorola E1 Motorola E680 Motorola L2 Motorola L6 Motorola L7 Motorola V3 Motorola V3I Motorola V360I 19 20 8 21 2 4 ( RESET 26 27 TECHNICAL SPECIFICATIONS CD/MP3/WMA PLAYER SECTION Signal to Noise Ratio Channel Separation Frequency Response > 60 dB > 50 dB (1kHz) 20Hz - 20 kHz TUNER (FM) Frequency range Intermediate frequency Sensitivity Stereo separation Signal to noise ratio Channel step 87.5-108 MHz 10.7 MHz 2.8 µV 30 dB 50 dB 50 kHz LINE-OUT Output Impedance 350mV 10k Ohm LINE-IN Frequency Response Sensitivity Impedance 20 Hz - 20 kHz 775 mV 20k Ohm GENERAL Power Supply Speaker impedance Output power Fuse 12V DC (10.8-15.6V allowable) 4 or 8 ohm 40W x 4CH 10A Note: Specification and the design are subject to possible modification without notice due to improvements. Instructions on environment protection Do not dispose of this product in the usual household garbage at the end of its lifecycle; hand it over at a collection point for the recycling of electrical and electronic appliances. The symbol on the product, the instructions for use or the packing will inform about the methods for disposal. The materials are recyclable as mentioned in this marking. By recycling, material recycling or other forms of re-utilization of old appliances, you are making an important contribution to protect our environment. Please inquire at the community administration for the authorized disposal location. ALL RIGHTS RESERVED COPY RIGHT DENVER ELECTRONICS A/S 024022 www.denver-electronics.com E