Download AUTOHELM ST3000 Service manual
Transcript
D296 ST3000 Autopilot Z155, ST3000 Autopilot Service Manual Warning CE Marking of Equipment/Replacement Parts If the Autohelm equipment under repair, test, calibration, installation or setting to work carries the European CE mark, only parts and components supplied or approved for such use by Raytheon should be used in order to maintain compliance with the relevant CE requirements. Incorporation, use or attachment, by any means, of parts or components not supplied for or not approved for such use by Raytheon or, if supplied or approved for use by Raytheon, not properly fitted in accordance with instructions published, provided or recommended by Raytheon, may cause the equipment to malfunction and, in particular, to become unsafe or to no longer meet the relevant CE requirements. In these circumstances, Raytheon Marine Europe Ltd excludes liability to the fullest extent permissible in law for any loss or damage including any liability for its contribution to such loss or damage by its negligent acts or omissions . ST3000 Autopilot Service Manual 83004-2 1 ST3000 Autopilot Chapter 1. Before Dismantling Before dismantling the autohelm ST3000 check the phase of the autopilot (If PCB condition allows) by driving the pilot, in standby mode, with the course change keys. +10 key –10 key Aft facing actuator Clockwise actuator rotation Anticlockwise actuator rotation Forward facing actuator Anticlockwise actuator rotation Clockwise actuator rotation All new spares PCBs are factory set to operate the pilot with the drive unit facing aft. A replacement PCB for an installation with the drive unit facing forward requires resetting. To reset the operating sense press the +1° and -1° course keys together for 5 seconds. The unit beeps for 10 seconds to confirm changeover and the display shows the new setting, either ‘Port’ (actuator sprocket facing forward) or ‘Starb’ (actuator sprocket facing aft’). The autopilot may be calibrated t to suit a particular vessel. Note the calibration settings and set up the new PCB if required. If the spares PCB contains software of a higher issue than before then the relevant Operating Supplement must be supplied when the equipment is returned to the customer. Note: Replacement PCBs require setting up to ST3000. Refer to Autopilot type selection on page 3 for instructions. 2 ST3000 Autopilot Service Manual 83004-2 ST3000 Autopilot Chapter 2. Special Functions Display test A display test feature included in ST3000 software checks that the display assembly has been re-fitted correctly. Display test is switched on by momentarily pressing the -1° and +10° keys together The display scrolls all four characters through from 0 to 9 and then displays each annotation. This sequence continues until either the ‘Standby’ or ‘Auto’ key is pressed or the unit is powered down. Autopilot type selection The Autohelm range of cockpit pilots all contain the same software but each pilot runs a different program. This is contained within the same chip but needs to be selected as follows: 1. Press the -10° and +1° degree keys until the display shows the pilot type number (Approximately 5 seconds) 2. Press the -10° and +1° degree keys again until the display flashes the pilot type number (Approximately 5 seconds) 3. Select the correct pilot type using the +1° and -1° degree keys 4. Save the setting by pressing the -10° and +1° degree keys until the normal Standby display appears (Approximately 2 seconds) Note: Changing Autopilot type will clear all calibration settings. Display of software code The software code of the pilot can be displayed as follows: 1. Switch the pilot to standby mode 2. Press the Standby key until the display shows P followed by a number. (Approximately 10 seconds) The number indicates the version of software fitted, e.g. P 0 6 indicates Version 6 software Calibration lockout To stop access to compass linearisation and calibration functions on the ST3000 autopilot: 1. Press the -1° and Standby keys for 10 seconds until the displayshows CAL ON (or CAL OFF) 2. Toggle between CAL ON and CAL OFF using the -1° and +1° keys 3. Store the selected setting by pressing the -1° and Standby keys for 10 seconds, when the control head returns to normal operation. Any attempt to linearise the compass or enter calibration when the lockout function is enabled will result in the display showing Cal Off. In this condition the user cannot change any settings. ST3000 Autopilot Service Manual 83004-2 3 ST3000 Autopilot Chapter 3. Functional Test Overall function Connect actuator to Control Head and apply power to unit Unit beeps, and shows 3000 and then displays a magnetic heading, with flashing 'C' OK No Change PCB. Restart. Yes Press & Hold +10 key. Check motor runs. OK No Yes Press & Hold -10 key. Check actuator runs. OK No Yes Press AUTO and check display shows 'A' followed by a heading. OK No Change PCB. Restart. Disconnect power and remove drive module. Disconnect motor spade terminals and apply 10V DC to motor terminals. Check motor runs. (See Figure 3). Yes OK Hold unit vertical. Rotate it in clockwise direction; check actuator rotates anti-clockwise (STBD set up) or clockwise (PORT set up) No Change motor. Restart. Yes Reverse 10V on motor. Check motor runs. No OK OK No Change motor. Restart. Yes Yes Hold unit vertical, rotate it an anti-clockwise direction; check actuator rotates clockwise (STBD set up) or anti-clockwise (PORT set up) Check motor connections and wires. OK No Change faulty item(s). Restart. Yes OK No Change PCB. Restart. Yes Unit OK Check fluxgate (SECT 5.6) OK No Change fluxgate. Restart. Yes Change PCB. Restart. D4103-1 4 ST3000 Autopilot Service Manual 83004-2 ST3000 Autopilot Fluxgate compass assembly Remove the fluxgate assembly (see Figure 2). The compass can be checked with a DVM as follows: Connect meter across Resistance 1 and 2 <10 ohms 3 and 5 < 5 ohms 3 and 4 < 5 ohms 1 and 3 Open circuit No connection 1 2 3 4 5 D4104-1 Figure 1. Fluxgate electrical connections ST3000 Autopilot Service Manual 83004-2 5 ST3000 Autopilot Chapter 4. Disassembly/Assembly SeaTalk Deck Plug Pin carrier Plug pin (x3) Plug pin screw (x3) Plug body Screw (x2) Metal sleeve (x3) Blue wire Brown wire Cable assembly (3016-104) Assemble sleeve to wire. Pinch sleeve with pliers. Insert sleeve into plug pin and tighten screw to retain. Cut off excess metal sleeve to prevent short circuit. Repeat process for remaining wires. Yellow wire Cable clamp Cable seal Clamp nut D4107-1 Electrical connections Wire colour Description Brown +12V nominal supply Blue 0V supply ST3000 Autopilot Display Unit Spare parts list The item numbers refer to Figure 2: ST3000 Autopilot display unit. Item Spare Description Part No. Comments – Control Head Q056 Complete head LCD kit, including LCD surround LCD Elastomer Diffuser Reflector Locking wedge (x5) Q053 4 5 6 7 8 27 9 PCB assembly Q044 13 Fluxgate assembly M022 30 SeaTalk deck plug assembly D326 6 ST3000 Autopilot Service Manual 83004-2 LCD not included 29 (Note C) 4 5 6 7 2 (x6) 3 (x6) 28 1. Facia (Note A) 2. Keypad (x6) 17. Fluxgate drive 3. Actuator (x6) 18. Fluxgate sense B 4. LCD surround 19. Fluxgate sense common 5. LCD 20. Fluxgate sense A 6. Elastomer connector 21. SeaTalk data (yellow) 7. Diffuser 22. Shield (screen - black sleeve) 8. Reflector 23. +12V supply (brown) 9. PCB 24. Ground (blue) 10. Seal 25. Motor (black) 11. Gimbol support (x2) 26. Motor (red) 12. Gimbol support screw (x2) 27. Wedge (x4) 13. Fluxgate assembly 28. Shim 14. Rear case 29. Spacer (early units only) 15. Case screw (x4) 30. SeaTalk deck plug assembly 16. Fluxgate ground 1 8 9 13 10 Display bezel (4) 26 24 25 23 22 21 12 (x2) 11 (x2) PCB (9) Wedge (27) Insert wedge (27) as shown to secure display bezel leg 27 (x4) Early units Later units 16 30 15 (x4) 20 19 18 17 Note B Important: The fluxgate loom in some early units is wired differently. Notes: A. Keypads come bonded to facia on later units. B. Ensure that the fluxgate loom is formed around the outside of the rear case pillar. Failure to do so may result in the gimbal action being impaired and the autopilot performance degraded. C. Early production units have a spacer (29) which is effectively replaced by using 4 wedges (27) on later units. 14 D4101-1 ST3000 Autopilot Figure 2: ST3000 Autopilot display unit ST3000 Autopilot Service Manual 83004-2 7 ST3000 Autopilot ST3000 Drive Actuator Spare parts list The item numbers refer to Figure 3: ST3000 Autopilot drive actuator. Item Spare Description Part No. Comments – ST3000 drive module Q45 Complete drive 1 2 3 4 ST3000Gearbox/Drive assembly, including Pin Clutch flange Gearbox housing Seal 2,1 Clutch flange & pin H006 7 Motor Q101 10 Pod H001 Q102 Also part of Q102 Motor replacement If the gearbox is noisy when the motor is replaced, remove motor, rotate gearbox a small amount, and refit. 8 ST3000 Autopilot Service Manual 83004-2 1 2 Blue (M2) Brown (M1) 3 Red dot 4 5 6 7 16 1. Pin 2. Clutch flange 3. Gearbox housing 4. Seal 5. Flux ring 6. Location screw 7. Drive motor 8. Cap 9. Seal 17 8 9 10. Pod 11. Shroud 12. Grip 13. Seal 14. Location ring 15. Receptacle 16. Socket 17. 'O' ring 15 10 Brown (M1) Note: Connect a 10v dc supply to the actuator plug and measure the running current of the drive unit. < 2A - Drive healthy > 2A - Drive faulty Blue (M2) Pip 14 13 12 11 D4102-1 ST3000 Autopilot Figure 3. ST3000 Drive Actuator ST3000 Autopilot Service Manual 83004-2 9 ST3000 Autopilot Chapter 5. PCB Details D4108-1 Figure 4: Circuit Diagram 10 ST3000 Autopilot Service Manual 83004-2 ST3000 Autopilot PCB Layout Taken from Drawing No: 4155-010 Issue: J Date: 07.03.97 D4105-1 Figure 5: PCB Component Layout ST3000 Autopilot Service Manual 83004-2 11 ST3000 Autopilot PCB Component list Taken from Drawing No: 4155-010 Issue: J Date: 07.03.97 Raytheon Marine Company 676 Island Pond Road Manchester New Hampshire 03109-5420 Tel: (001 603) 647 7530 Fax: (001 603) 634 4756 Raytheon Marine Europe Limited Anchorage Park, Portsmouth Hampshire PO3 5TD Tel: (01705) 693611 Fax: (01705) 694642 http: //www.raytheon.com 12 ST3000 Autopilot Service Manual 83004-2 D4106-1