Download ClearOne PSR1212 Specifications

PSR1212 Digital Matrix Mixer
Installation & Operation Manual
ii
©2002 ClearOne Communications, Inc. All
rights reserved. No part of this document may
be reproduced in any form or by any means
without written permission from ClearOne
Communications, Inc. Printed in the United
States of America. ClearOne Communications,
Inc. reserves specific privileges. Information
in this document is subject to change without
notice.
PSR1212 Installation and
Operation Manual
ClearOne Part No. 800-155001 Jan 2007(Rev. 7.1)
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
iii
PSR1212 Installation and Operation Manual
Table of Contents
CHAPTER 1: Introduction
. . . . . . . . . . . . . . . . . . . . . .1
Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1. . . .
New Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2. . . .
Professional Services Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . .
Product registration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. . .
Product returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. . . .
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. . . . .
Controls and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. . . .
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. . . .
Rear panel
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. . . .
Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. . . . .
Expansion bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. . . .
Operational Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. . . .
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. . . .
Equipment placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. . .
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. . . .
G-Ware requirements
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. . .
CHAPTER 2: Installation
. . . . . . . . . . . . . . . . . . . . . . .9
Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9. . . .
To connect the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
....
Networking Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
.....
Expansion bus connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
...
Device IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
....
Mixer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
....
LCD Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
.....
LCD menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
....
System menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
....
RS-232 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
....
Meter menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
....
Inputs menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
....
Outputs menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
....
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
iv
CHAPTER 3: System Configuration . . . . . . . . . . . . . . . .21
G-Ware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating Floppy Disk Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing G-Ware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
22
22
Site Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Creating a new site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Adding a PSR1212
24
...........................................
Configuring Unit Properties
.....................................
25
G-Ware Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Flow Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Matrix Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Audio Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Expansion bus O–Z routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Process A–H routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Cross point attenuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Matrix report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
Inputs 1–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
Inputs 9–12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42
Outputs 1–12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
Expansion Buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
From Expansion Bus O–Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
To Expansion Bus O–Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Processing A–H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
CHAPTER 4: Advanced Configuration . . . . . . . . . . . . . .53
Overview
...................................................
53
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Creating presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
Running presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
58
Running multiple presets simultaneously . . . . . . . . . . . . . . . . . . . . . . . . . . . .
58
Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Creating macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
Editing macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
Running macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
v
CHAPTER 5: Operation
. . . . . . . . . . . . . . . . . . . . . . . .65
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Signal Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
Document Compare Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
Print Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
GFirm Firmware Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
G-Ware Switcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
Copy and paste settings
73
Message Log
........................................
................................................
73
Monitoring Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
Gate View
..................................................
73
Meter Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
CHAPTER 6: Control . . . . . . . . . . . . . . . . . . . . . . . . . .75
GPIO Builder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Control/Status A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Remote Builder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
XAP IR Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
ClearOne Control Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
RS-232 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Remote modem access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
Serial commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
Command Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
APPENDICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Appendix A: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
83
Appendix B: Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
84
Appendix C: Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
88
Appendix D: Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
Appendix E: Serial Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
Appendix F: Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
124
Appendix G: Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
126
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
vi
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 1: Introduction
Product overview
Congratulations on purchasing the PSR1212, a highly advanced twelve-by-twelve
digital matrix mixer with audio processing. It utilizes an internal macro language
and 32 user-definable presets to quickly adapt to a variety of sound reinforcement
and room-combining applications in auditoriums, stadiums, theatres, gymnasiums,
hotel/convention centers, conference rooms, training rooms, and boardrooms.
The PSR1212 facilitates local and remote PC setup and diagnostics, logic
outputs, and automatic gated microphone operation. Gating parameters for
microphone inputs can be individually customized, while automatic gain control
keeps the overall sound level consistent. Eight of the 12 channels can be
configured as an automatic microphone mixer.
All microphone mixing parameters can be customized and any combination of
inputs can be routed to any combination of outputs, with attenuation adjustments
at each cross point. This allows flexibility in accommodating different applications
and customer requirements.
Adjustments in routing, level, and other functions can be made through
presets activated through a closure on the rear panel, an RS-232 serial interface,
or a control panel through the RS-485 port.
The PSR1212 features eight audio processing blocks, each with 15 filters.
Each filter can be configured as a parametric equalizer, high pass, low pass, CD
horn, high shelving, low shelving, all pass, or crossover. This allows you to tailor
the PSR1212’s audio response to optimize the audio quality and fidelity in a wide
variety of venues.
The GPIO (general purpose input/output) allows switching among any of 32
user-stored presets. This gives you real-time flexibility to meet a variety of audio
reinforcement requirements.
Network-based interconnectivity allows up to eight PSR1212s to be
connected and controlled as a single unit, allowing microphone coverage in
applications requiring up to 64 mics.
The PSR1212’s Macro Pro™scripting language allows the unit to function
without the need for an external controller. However, it can be easily interfaced to the
ClearOne Control Panel or XAP IR Remote via either of the two RS-485 ports. The
unit can also interface with a PC or external controller through the RS-232 port.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
2
Introduction ~ New Features
New Features
•
Virtual references. The PSR1212 now features four user-definable virtual
references. These references can use multiple signals as the PA Adapt
reference point without sacrificing an analog output.
•
Front panel gain and mute control. Now gain and mute adjustments can
be made from the front panel. Using these controls allows you to make
quick volume and mute changes without connecting through G-Ware.
•
Safety Mute. The new Safety Mute button on the main G-Ware toolbar
allows you to mute all outputs with one simple click if feedback or audio
problems occur during the configuration process.
•
Preset and Macro Passwords. You can now password protect your presets
and macros to prevent unauthorized changes.
•
Clear Matrix. This new button on the Matrix Screen makes it easy to clear all
cross point cells in the matrix. Simply click the button and confirm the action.
•
RAMP serial command. The new RAMP serial command (see page 119)
gives you greater control over gain adjustments. You can specify the rate at
which the gain increases and decreases as well as the target level.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ Professional Services Group
Professional Services Group
If you need any additional information on how to install, set up, or operate your
system, please contact us at one of the locations listed below. We welcome and
encourage your comments so we can continue to improve our products and serve
your needs.
ClearOne Communications ~ 5225 Wiley Post Way, Suite 500
Salt Lake City, Utah 84116
Technical Support
Telephone:
1.800.283.5936(USA) or 1.801.974.3760
Fax:
1.801.977.0087
E-mail:
[email protected]
Web site:
www.clearone.com
Sales and Customer Service
Telephone:
1.800.945.7730 (USA) or 1.801.975.7200
Fax:
1.800.933.5107 (USA) or 1.801.977.0087
E-mail:
[email protected]
ClearOne Communications EuMEA GmbH
Leonhardstr. 16-18, D-90443 Nuremberg, Germany
Telephone:
+49 911 955159-0
Fax:
+49 911 955159-10
E-mail:
[email protected]
Product Registration
Please register your PSR1212 online by visiting ClearOne Technical Support at
www.clearone.com. When your product is properly registered, ClearOne
Communications is better able to serve you should you require technical assistance.
Registration information is also used to notify you of upgrades and new product
information.
Product Returns
All product returns require a return authorization (RA) number. Please contact
ClearOne Technical Support before attempting to return your PSR1212 unit.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
3
4
Introduction ~ Unpacking
Unpacking
Ensure that the following items were received with your shipment:
ClearOne
is
not
responsible for product
damage incurred during
shipment. You must make claims
directly with the carrier. Inspect
your shipment carefully for
obvious signs of damage. If the
shipment appears to be damaged,
retain the original boxes and
packing material for inspection
by the carrier. Contact your
carrier immediately.
!
Figure 1.1. Equipment included with PSR1212 unit
Controls and Connections
Front panel
Figure 1.2. Front panel controls
A. LCD. This display is for PSR1212 setup in conjunction with the four
associated front-panel buttons [B, C, and D]. Baud rate and flow control
must be configured from the front panel; see the LCD Menu Tree on page 13
Front panel buttons are
also used to enter the
front panel passcode.
See page 26 for more details.
-
for the location of these in the menu system. Other functions accessed via
the front panel include system options, RS-232 configuration,
troubleshooting, and level readings.
B. Enter. This button is used when programming the PSR1212 via the LCD
window. To move deeper in the menu or execute a selected parameter, press
the Enter button.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
5
Introduction ~ Controls and Connections
C.
s/tThese buttons scroll up and down through vertical programming options
within a specific PSR1212 programming parameter or increases/decreases a
numeric value.
D. Esc. This button steps you out of a selected parameter or moves you up one
level in the menu. When a parameter has been displayed with the arrow
buttons [C], you can select it with the Enter button [B] to modify it. Then,
you can step out of the menu with the Esc button.
E. LED meter. This assignable, peak-level LED bar meter is used to display
the audio level of an input, output, or processing channel of the PSR1212.
F.
Meter. Takes you directly to the Meter branch of the PSR1212’s LCD menu
tree.
G. LED 1–8. These LEDs indicate Inputs 1–8 gate status.
Rear panel
Expansion Bus
In
Out
Figure 1.3. Rear panel connections
A. Power. This power module accommodates power ranging from
100–240VAC, 50/60Hz. The module uses an IEC-type connector. No
switching is required.
B. Inputs 1–8. These Phoenix block connectors are for connection of eight
mic-level or line-level (selectable) inputs. These connectors are typically
used for mics, but can be configured for use with VCRs, CD players, etc.
These inputs can be mixed in any gated or non-gated combination and
routed to any of the 12 outputs. Default input level is -55dBu. For more
information about input adjustments, see page 32. For electrical
specifications, see Appendix A: Specifications.
C.
RS-485 Remote Panel A/B Port. These four-pin Phoenix connector ports
allow you to control the PSR1212 with the ClearOne Control Panel or XAP
IR Remote Control.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
6
Introduction ~ Controls and Connections
Power is supplied through the RS-485 ports to the remote Control Panels
from the PSR1212. This power is limited to a total of 300mA at 15 volts
for each connector. Over-current protection is provided on the +15V pins to
prevent damage in the event of shorting. External power can be provided to
control devices when more current is required. See page 89 for maximum
cable run distances when using ClearOne Control Panels.
D. Control/Status Ports A and B. These two female DB-25 connector are used
to connect control devices to the PSR1212. The control devices have access
to the command set for the PSR1212 and can be used for common functions
such as volume control, muting, preset change, room combining, etc.
Devices can be connected to either port.
For instructions on how to program the control and status pins, see the
GPIO section on page 75. The default settings allow control and status of
inputs, outputs, volume, and presets. These pins are active low. The 32
presets can also be activated via these connectors. For pinout and default
information, see Appendix B.
E. Outputs 1–12. These three-pin Phoenix connectors are for connection of
twelve line-level balanced outputs with three-pin Phoenix connectors. These
outputs are typically used for connection to VCRs, tape recorders,
amplifiers, and other audio devices. These outputs can be configured to
contain any combination of gated and non-gated inputs. The nominal output
level is 0dBm.
F.
Inputs 9–12. These Phoenix connectors are for connection of up to four
line-level inputs. These are typically used for connection of VCRs, tape
players, CD players, and other audio sources. They can be routed to any
output or multiple outputs. Nominal level is 0dBu.
G-H.Expansion Bus In/Out. This RJ-45 connector is part of the expansion bus
(E-bus), which allows up to eight PSR1212 or XAP 800/400 units and up
to 16 XAP TH2 units to be networked together. The E-bus consists of two
buses: one for control, the other for passing audio and mic information (see
Control bus, page 7). Using Cat 5 twisted-pair cable, you can separate
adjoining units up to 80 feet (24 meters). See the diagram on page 11.
I.
RS-232. This female DB-9 serial port is for interconnection between the
PSR1212 and a PC, modem, or other external control device. For serial
protocol, see Appendix B: Connector Pinouts.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
7
Introduction ~ Networking
Networking
Expansion bus
The digital mix-minus expansion bus (RJ-45 LAN) is used to connect up to eight
PSR1212s (or XAP 800/400s and 16 XAP TH2 units), where the total number of
microphone inputs does not exceed 64. The maximum distance between
interconnected PSR1212 or XAP 800/400 units is 80 feet (24 meters). Connecting a
XAP TH2 must not increase the cable length between two PSR1212s, XAP 800s
and/or XAP 400s beyond 80 feet. ClearOne recommends that category five twistedpair (10BaseT LAN) cable be used.
The expansion bus (E-bus) allows audio routing between destinations on the
E-bus network. The E-bus contains 12 independent digital audio buses labeled O–Z
which can route mic or line level inputs in any combination across the E-bus
network. The O–Z buses are divided into two groups (O–R and S–Z) based on their
capabilities and default settings. The E-bus also contains four PA adapt reference
buses, four global gating buses, and one control bus.
•
O–R buses. These four audio buses are defaulted as the mic mix buses; they
can communicate the NOM count and mic mixing parameters across the
network to other PSR1212s. All gated mics are routed to the 0 bus by
default.
•
S–Z buses. These eight buses are defaulted as auxiliary mix buses. They are
used to route auxiliary audio, such as from a CD player or VCR, to and from
other units on the network. These buses are also used as mic mix buses when
NOM count is not required.
•
PA Adapt Reference buses. These buses allow an input from a PSR1212 to
reference an output on another linked PSR1212 or XAP 400/800. See PA
Adapt and AEC Reference on page 37 for more information.
•
Global Gating Groups A–D buses. These mix-minus buses are defined as
microphone gating groups which support first-mic priority, maximum
number of mics, etc. and work across all linked units. Unlike the audio
buses, they contain only mic status and gate parameters. See page 39 for
more information about gating groups.
•
Control bus. The control bus is an independent channel from the E-bus’s
audio channel; it uses a different pair of wires on the same E-bus cable. This
allows control information to pass even if the units are not using the audio
link. The PSR1212 supports the full set of commands through the control bus.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
-
The
latency
propagation delay
<1ms.
or
is
8
Introduction ~ Operational Requirements
Operational Requirements
Power
The PSR1212 automatically accommodates voltage requirements of 100–240VAC,
50/60Hz, 15W.
Equipment placement
The PSR1212 units are designed for installation in a standard 19-inch equipment
rack. You can also purchase side panels for desktop placement. See Appendix D for
a list of accessories.
Environmental
The PSR1212 can be safely operated in a room with varying temperatures between
32 ° F/0 ° C and 110 ° F/43 ° C.
G-Ware requirements
ClearOne’s G-Ware software requires the following minimum system configuration:
•
Minimum RAM requirement is determined by the operating system
Windows
Windows
Windows
Windows
Windows
Windows
95 OSR2
98
ME
NT
2000
XP
64MB
64MB
64MB
64MB
128MB
256MB
•
PII 200MHz (or AMD equal) or higher processor
•
8MB Video Card
•
1024x768 (16 bit) High Color monitor
•
Internet Explorer 4
•
20MB of free hard disk space
•
RS-232 COM port
•
CD-ROM drive
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 2: Installation
The PSR1212 is designed for easy installation and setup. All connections are made
through rear-panel connectors. This chapter provides instructions on making
hardware connections, creating an expansion bus network, assigning device ID
numbers, selecting the mixer mode, and using the front panel LCD menus.
Hardware Setup
The diagram below illustrates the typical connections that are made for a PSR1212
system.
ClearOne
Figure 2.1. PSR1212 installation diagram
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
10
Installation ~ Hardware Setup
Expansion Bus
In
Out
Figure 2.2. PSR1212 rear-panel connectors
To connect the unit
1.
Place the unit in a standard 19-inch rack and attach it securely.
2.
If you are using a custom controller for control and status, plug it into the
DB-25 Control/Status A or B port [D].
If you are using an external RS-232 controller, connect it to the
RS-232 port [I].
The three terminals in
the Phoenix connector
correspond with the
rear-panel audio contacts (from
left to right): + (positive), –
(negative), and (ground).
3.
-
Wire the inputs and outputs to the PSR1212 using the provided threeterminal Phoenix push-on connectors. These connectors are designed for
easy wiring; simply insert the desired wire into the appropriate connector
opening and tighten down the top screw.
4.
•
Inputs 1–8 [B] Mic or line level inputs
•
Inputs 9–12 [F] Line level inputs only
•
Outputs 1–12 [E] Line level outputs
If you are using a ClearOne Control Panel or XAP IR Remote, wire it to the
RS-485 port [C] using one of the provided four-terminal Phoenix push-on
connectors.
5.
Plug in the PSR1212 to complete the installation. The power output [A]
will operate at any level between 100–240VAC and 50–60Hz.
Figure 2.3. Phoenix push-on connector
If you are installing only one PSR1212 and are not connecting it to any other XAP
or PSR1212 units, you have completed the hardware installation.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
11
Installation ~ Networking Units
Networking Units
Expansion bus connections
Using the Expansion Bus ports (RJ-45), you can connect up to eight PSR1212s or
XAP 800/400s and 16 XAP TH2 units, where the total number of microphone
inputs does not exceed 64. Make connections between units in daisy-chain fashion
using the short RJ-45 jumper. If your units are further apart, use category five
twisted-pair cable.
The maximum distance between interconnected PSR1212 or XAP 800/400
units is 80 feet (24 meters). Expansion bus cable length is calculated between
PSR1212s and XAP 800s/400s.
PSR1212 unit 0
PSR1212 unit 1
Expansion Bus
In
Out
Expansion Bus
Out
In
PSR1212 unit 2
Expansion Bus
In
Out
Figure 2.4. E-bus connection diagram
To create an expansion bus network
1.
Plug the expansion bus terminator in the Expansion Bus In connector of
the first unit in the network.
2.
Connect the RJ-45 jumper cable (or Cat 5 twisted pair cable) to the
Expansion Bus Out connector of the first unit in the network and
Expansion Bus In connector of the second unit. Continue connecting units
in the same fashion.
3.
Plug the expansion bus terminator in the Expansion Bus Out connector on
the final unit to complete the network connections.
If connecting to other
units, make sure the
first unit in your E-bus
network is a PSR1212 or XAP
800/400 instead of a XAP TH2.
-
If the E-bus network is not connected properly, the front panel LEDs will
flash on the units that are physically connected to the network. To correct
the problem, check for broken connections and reconnect the expansion bus
cables.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
RS-232
system-wide
con-trol can be provided
by any PSR1212 or XAP
800/ 400 unit in the network.
-
12
Installation ~ Networking Units
If the same device ID is
assigned to more than
one unit on the E-bus
network, the Meter LED “+12”
will flash red and the Mic LEDs
“1,” “2,” “4,” and “8” will flash
green on the affected units. To
correct the problem, change the
device ID on one of the
conflicting units.
-
Device IDs
Once your expansion bus connections are made (and if you have more than one
PSR1212 at a site), you need to set up a unique expansion bus device ID number—
a
network address—
for each PSR1212 on the network. As shipped from the factory, all
PSR1212s are set to device ID 0.
To assign device IDs
1.
Press the front-panel Enter button, then scroll through the menu until the
System menu is visible.
2.
Press Enter, then scroll through the menu until Device ID is visible.
3.
Press Enter, then scroll through the eight (0–7) options. When the desired
device ID is visible, press Enter to select it. (You can also set the device ID in
the Unit Properties window of G-Ware software. See page 25.)
4.
-
You can also use G-Ware
to select a mixer mode.
See page 25.
Repeat this process for each PSR1212 on the expansion bus network.
Mixer mode
There are two mixer mode settings: slave (default) and master. A master unit is not
required in a networked system and in most installations, all units will be slaves.
Master units ignore audio from upstream units. This prevents audio from being
received from units above the master unit in the network. However, global control of
the system is still maintained by whichever PSR1212 or XAP 400/800 unit is
connected to a control device through its RS-232 or RS-485 ports. Control is not
affected by master/slave designations.
In Figure 2.5, the third unit in the network is a master. It prevents the audio
from the first and second units from being passed down the network chain.
Likewise the second master unit in the network will not pass on the audio from the
unit before it. The third unit provides system-wide control through a connection to
its RS-232 port.
To select a mixer mode
1.
Press the front panel Enter button and scroll through the menu until System
menu is visible. Press Enter to select the menu.
Figure 2.5. E-bus network with master units
2.
Scroll through the System menu and select Mixer Mode.
3.
Select the mixer setting you want to use.
Repeat for additional units.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
13
Installation ~ LCD Programming
LCD Programming
The PSR1212’s front panel is intuitive to operate, thanks to its simple interface: a
2x16 character LCD, menu buttons, and a peak-level LED bar meter. Although most
of the PSR1212’s features are programmed with G-Ware software (see page 23),
-
G-Ware software is
required to complete
system setup.
the front panel can be used for simple adjustments and meter monitoring.
When power is applied to the PSR1212, the LCD panel will first read
INITIALIZING. If an error is displayed, contact technical support. When
initialization is complete, “PSR1212”is displayed on the top line and “Unit 0”is
displayed on the bottom line.
LCD menu tree
The menu tree features five main menus, each with submenus. These branches
typically end when an adjustable parameter or viewable value is reached. The
-
Pressing Esc at the top
of the tree does nothing.
diagram below shows the LCD menu tree.
Figure 2.6. LCD menu tree
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
14
Installation ~ LCD Programming
The five main menus are: System, RS-232, Meter, Inputs, and Outputs. All
submenu items are arranged under these menus. Use the Enter button to select items
and the s and tbuttons to scroll through menus and submenus. When the last menu
item is reached, the display scrolls back to the beginning of the list. The Esc button
allows you to back out of the menus.
To adjust a parameter
1.
Scroll to the parameter you want to adjust. Press Enter to select the
parameter. The parameter will flash when selected.
2.
Adjust the value with the s and tbuttons. As the value is adjusted, the
parameter is updated immediately.
3.
To store the new value, press Enter. To discard the change and revert back
to the old value, press Esc.
If the Meter button is pressed while a parameter is being adjusted, the LCD
will switch to the Meter menu.
System menu
There are eight system-level parameters (see Figure 2.6): Select Preset, Run Macro,
Lock Panel, Set Passcode, Device ID, Unit ID, Mixer Mode, and Firmware Version.
Select Preset
The Select Preset menu item allows for one of 32 preprogrammed presets to be
selected for PSR1212 use. To select a preset, scroll through the numbered presets
(1–32) until the desired preset is visible, then press Enter to run the preset.
Run Macro
The Run Macro menu item allows you to execute a macro. To select a macro, scroll
through the numbered macros (1–255) until the desired macro is visible, then press
Enter to run the macro.
Lock Panel
The front panel can be locked to prevent unauthorized adjustments to the PSR1212.
To lock the front panel, use the s/tbuttons to select Lock Panel from the System
menu, and press Enter. Lock Panel selections are Off, On, or On at Timeout. Press
Enter to enable your selection.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
15
Installation ~ LCD Programming
To unlock the front panel, attempt to adjust a parameter. The PSR1212 will
prompt for the passcode. Upon entering the fifth character (if entered correctly),
the front panel will unlock. The default passcode for all boxes is sstt
Enter.
Set Passcode
Once the PSR1212 is unlocked, the passcode can be changed. Before the PSR1212
will allow passcode changes, the new passcode must be entered, then re-entered to
validate the new passcode.
The front panel passcode can also be set (and reset) within G-Ware. See page
26 for more information.
Device ID
The PSR1212’s device ID is set from this menu. There are eight device ID selections
to choose from (0–7). Select the network position you want to use. Within a single
site, you must assign different device ID numbers for each PSR1212 unit. See Device
IDs, page 12.
Unit ID
The Unit ID menu selection allows you to access the read-only address set at the
factory. This unique ID number identifies your particular PSR1212 unit and cannot
be changed.
Mixer Mode
This setting allows you to set to master or slave mode. See page 12 for details.
Firmware Version
This menu selection allows you to view which firmware version is being used. This
information cannot be changed.
RS-232 menu
There are four submenus under the RS-232 menu: Baud Rate, Flow Control, Enable
Modem, and Clear Password.
Baud Rate
This parameter allows you to set the PSR1212’s baud rate to 9.6kbps, 19.2kbps,
38.4kbps, or 57.6kbps. Default is 38.4kbps. Select the baud rate you want to use,
then press Enter.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Menu items can still be
scrolled through when
the panel is locked.
However, settings cannot be
entered until the panel is
unlocked with the appropriate
passcode.
-
16
-
Installation ~ LCD Programming
ClearOne recommends
that you leave Flow
Control enabled.
Flow Control (hardware)
The PSR1212 uses the RTS and CTS pins on the RS-232 port to regulate the
transmission and reception of data. You can enable or disable flow control on the
front panel of unit and select the flow control type in the Site Properties window of
G-Ware (see page 23). If you select On (default) from the front panel menu, select
Hardware as the flow control type in the Site Properties window. If you disable flow
control on the front panel, select None in the Site Properties window. When None is
selected, the PSR1212 ignores flow control, making the connected external control
device ensure that data is not lost. Software flow control (Xon/Xoff) is supported by
the XAP/PSR units and is used only with a pass-through device, such as a modem.
To avoid communication errors, ClearOne strongly recommends that you
connect all DB-9 pins and enable flow control when connecting to a PC.
The modem initialization
string can be set only via
the
MINIT
serial
command (see page 113 or the
G-Ware software). It cannot be
set through the front panel LCD.
-
You can set the modem
password using the
MPASS serial command
(see page 114) or in G-Ware (see
page 26).
-
Enable Modem
This parameter configures the RS-232 port for connection of a modem. When On is
selected, the PSR1212 will send an initialization string to the modem on power-up
and require a password before data transfer is allowed through the port. When Off
(default) is selected, the password is disabled.
To use the PSR1212 with a modem
1.
Match the baud rate of the modem to that of the PSR1212.
2.
Turn off Serial Echo on the modem.
3.
Turn off the modem’s response mode (e.g., no OK messages, ring, etc.).
4.
Enable auto-answer on the modem.
Clear Password
This parameter allows you to erase the serial port (modem) password in case it has
been forgotten. Select Yes to keep the current password or No to erase it. Press
Enter to enable your selection.
Meter menu
There are four submenus under the Meter menu: Inputs, Outputs, Processing and
Default Meter. The meter selection determines what is shown on the front panel
peak-level LED display. When the meter is selected in the LCD menu tree, the LCD
displays peak level indications as well. Use the s and tbuttons to select the Meter
menu, then scroll through the options and press Enter when you reach the desired
option.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
Inputs
Select which input (1–12) you want to monitor on the LCD and LED display. Scroll
to the input, then press Enter. The meter displayed is the post-gain meter.
Outputs
This submenu allows you to choose which output (1–12) you want to monitor on the
LCD and LED display. Scroll to the output you want to monitor, then press Enter.
Processing
This submenu allows you to choose which processing channel (A–H) you want to
monitor on the LCD and LED display. Scroll to the output you want to monitor, then
press Enter.
Default Meter
This submenu determines what is displayed on the LED meter when a meter is not
specifically selected elsewhere in the Meter menu. The default is Output 12.
The Meter Reference Point diagram on page 19 shows the meter pick-up
points (
M
) in the PSR1212 signal path.
Inputs menu
There are two submenus under the Inputs menu: Mute and Gain. To access these
submenus you must first select the input. Choose from Inputs 1–12 or Global. Use
the s and tbuttons to select the Inputs menu, then scroll through the options and
press Enter when you reach the desired option.
Mute
This submenu allows you to turn mute on or off (default) for the selected input.
Gain
This submenu allows you to adjust the gain for the selected input. Use the s and t
buttons to increase or decrease gain.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
17
18
Installation ~ LCD Programming
Outputs menu
There are two submenus under the Outputs menu: Mute and Gain. To access these
submenus you must first select the output. Choose from Outputs 1–12. Use the s and
tbuttons to select the Outputs menu, then scroll through the options and press Enter
when you reach the desired option.
Mute
This submenu allows you to turn mute on or off (default) for the selected output.
Gain
This submenu allows you to adjust the gain for the selected output. Use the s and t
buttons to increase or decrease gain.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
M
M
Off
On
M
Off
On
Off
NOM
On
Mute
Output Gain
Post-gain
Meter
Output 3
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Phantom
Power
On/Off
Input 1
Input 2
On Off
Mute
Input Processing
M
Mic 55, 25
Line
Pre-gain
Meter
All Pass
Low Pass
High Pass
Notch
PEQ
Input 4
Off
On
M
Off
On
Off
NOM On
Mute
Output Gain
Post-gain
Meter
Output 7
M
On Off
Pre-gain
Meter
M
Mic 55,25
Line
Automixer
Input 7
Input 8
M
M
M
M
Pre-gain
Meter
M
Off
On
Off
On
Input 10
Fine Input Gain
Post-gain
Meter
AGC
Mute
Off
On
Off
On
To Matrix
M
Output 11
M
Pre-gain
Meter
M
AGC
Mute
Off
On
Off
On
Input 11
Fine Input Gain
Post-gain
Meter
Off
On
Off
NOM On
Mute
Output Gain
Post-gain
Meter
Matrix
AGC
Input 9
Off
On
Off
NOM
On
Mute
Output Gain
Post-gain
Meter
Output 10
Mute
Fine Input Gain
Pre-gain
Meter
M
Off
On
NOM Off
On
Mute
Output Gain
Post-gain
Meter
Post-gating
Meter
Gated Audio
Non-Gated Audio
Pre-gain
Meter
M
Mic 55, 25
Line
Phantom
Power
On/Off
Chairman Override
On/Off
Adaptive Ambient
Microphone Activation
Auto gate/Manual gate/On/Off
M
Pre-gain
Meter
M
Mic 55, 25
Line
Phantom
Power
On/Off
System-Wide
Automixing
Parameters
Input 6
Post-processing
Meter
Input 5
AGC
Pre-gain
Meter
M
Mic 55, 25
Line
Phantom
Power
On/Off
Fine Input Gain
M
Post-gain
Meter
Fine Input Gain
M
Post-gain
Meter
M
Post-gain
Meter
Fine Input Gain
Off
On
Off
NOM
On
Mute
M
Output 9
Post-gain
Meter
Input
Processing
M
Fine Input Gain
Output 8
Output Gain
Post-gain
Meter
Input
Input
Processing Processing
NOM Off
On
Mute
Output Gain
Output 6
Post-gain
Meter
Phantom
Power
On/Off
Fine Input Gain
M
Post-gain
Meter
Input
Input
Processing Processing
Phantom
Power
On/Off
4 Filters
Input 3
Off
On
NOM Off
On
Mute
Off
On
NOM Off
On
Mute
Output Gain
Post-gain
Meter
M
M
Post-gain
Meter
Output 5
Output Gain
Output 4
Figure 2.7. Meter Reference Point diagram
M
Post-gain
Meter
M
Pre-gain
Meter
M
Pre-gain
Meter
Mic 55, 25
Line
Phantom
Power
On/Off
M
Mic 55, 25
Line
Phantom
Power
On/Off
Pre-gain
Meter
Mic 55, 25
Line
Fine Input Gain
M
Post-gain
Meter
Fine Input Gain
M
Post-gain
Meter
Fine Input Gain
M
Post-gain
Meter
M
Post-gain
Meter
Input
Input
Input
Processing Processing Processing
Off
NOM
On
Mute
Off
On
Off
NOM
On
Mute
Output Gain
Post-gain
Meter
Output Gain
Post-gain
Meter
Output 2
M
M
Pre-gain
Meter
M
AGC
Mute
Off
On
Off
On
M
500mS
Delay
Compressor
Gain Adjust
H
= Meter Reference Point
PEQ
CD Horn
Bessel Crossover
Butterworth
Linkwitz-Riley
15 Filters
Assignable Processing
G
A
Assignable
Processing
F
B
Assignable
Processing
E
C
Assignable
Processing
D
D
Assignable
Processing
C
E
Assignable
Processing
B
F
Assignable
Processing
A
H
G
Assignable
Processing
Processing outputs are looped back into the matrix.
Assignable
Processing
All Pass
Low Pass
High Pass
Low Shelving
High Shelving
Notch
From Matrix
Input 12
Fine Input Gain
Post-gain
Meter
Off
On
NOM Off
On
Mute
Output Gain
Post-gain
Meter
Output 12
Control/Status
Post-processing
Meter
M
To Matrix
Mute
B
Front Panel
Control
Control
Network
RS-485
Control
Logic
Control/Status
Expansion Bus
RS-485
RS-232
A
Expansion Bus In/Out
O Mixing Bus
P Mixing Bus
Q Mixing Bus
R Mixing Bus
S Mixing Bus
T Mixing Bus
U Mixing Bus
V Mixing Bus
W Mixing Bus
X Mixing Bus
Y Mixing Bus
Z Mixing Bus
Output 1
Installation ~ LCD Programming
19
Control Bus
20
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 3: System
Configuration
ClearOne’s G-Ware software provides an easy interface for configuring and
controlling your PSR1212. While some configuration can be done using the front
panel LCD menus, G-Ware is required to complete the custom configuration of your
audio conferencing system. If you are using the default settings, no configuration is
necessary.
This chapter describes how to install G-Ware and create a site. It also
describes all configurable parameters of your system. These descriptions are
designed to be used as a guide as you make adjustments for your particular
installation. It is not necessary to configure all parameters.
G-Ware Requirements
ClearOne’s G-Ware software requires the following minimum system configuration:
•
Minimum RAM requirement is determined by the operating system
Windows
Windows
Windows
Windows
Windows
Windows
95 OSR2
98
ME
NT
2000
XP
64MB
64MB
64MB
64MB
128MB
256MB
•
PII 200MHz (or AMD equal) or higher processor
•
8MB Video Card
•
1024x768 (16 bit) high color monitor
•
Internet Explorer 4
•
20MB of free hard disk space
•
RS-232 COM port
•
CD-ROM drive
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
22
System Configuration ~ Installing G-Ware
Creating Floppy Disk Copies
Depending upon the computer equipment you have available, you might need to
install G-Ware software from floppy disks rather than the included CD. To do this, a
Disk Copy program is provided in G-Ware that allows you to transfer G-Ware to
floppy disks. You will need a PC with a CD-ROM drive to make the transfer. You can
access the Disk Copy program in the following ways:
•
After installing G-Ware, go to the Windows® Start menu, select Programs,
then ClearOne G-Ware, then Create Install Floppy Disks.
– or –
•
In the G-Ware section of the Audio Video Product CD, click on Install Now.
Choose Create Installation Floppy Disks from the G-Ware setup menu.
Installing G-Ware
To install G-Ware
1.
Boot the PC to the Windows operating system. Ensure that all other
programs or applications are closed. Insert the Audio and Video Products
CD into the CD-ROM drive.
If the Autorun feature is enabled on the PC, the ClearOne Welcome window
opens. Click the Software tab and select G-Ware.
If the Autorun window does not open, open the Windows Start menu and
choose Run. Type “<drive>:\\clearone.exe”where <drive> is the letter of
the CD-ROM drive (e.g., D:\\clearone.exe).
To select an alternate
destination directory,
click Browse and use the
Choose Directory window to find
the desired location. Click OK to
return to the previous window.
-
2.
At the G-Ware window, click Install Now near the bottom of the window.
3.
Select Install G-Ware from the setup menu. The InstallShield Wizard
opens, and guides you through the Welcome and License Agreement
windows. At the Choose Destination Location window, choose the directory
where G-Ware will be installed. We recommend that you use the default
directory.
4.
Click Next or Yes to move to proceed through the windows that follow or
No or Cancel to end the installation process.
5.
Follow the onscreen instructions. You must restart your computer once
installation is complete.
Figure 3.1. Desktop icon
The G-Ware Program Folder is now added to your Start menu. You can start
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
23
System Configuration ~ Site Setup
Site Setup
Creating a new site
New site files are created through the Site Properties window in G-Ware. A site file
contains all information about a particular installation including all unit settings and
left
Whenever a mouse click
is indicated in this
manual, it refers to the
mouse button unless
properties. It also provides G-Ware with the necessary information to communicate
with the site hardware using your PC. Open G-Ware by double clicking the desktop
icon or by selecting G-Ware from the Start menu.
To create a new site
1.
Open the Site Properties window by selecting New Site from the File menu
or by clicking the New Site button on the toolbar.
2.
Figure 3.2.
New Site button
In the Site tab, enter the site name, author, company, location, room, and
description, using the Tab key or mouse to select each field.
3.
Click the Comm tab. Select the COM port, baud rate, and flow control you
want to use. ClearOne recommends that you leave Flow Control set to
Hardware. The Software setting is not supported by PSR/XAP units and is
typically used with modems.
4.
You can enable flow
control
using
the
PSR1212’s front panel
controls. See page 23.
-
If you plan to use a modem, select Use Modem and enter the phone number,
initialization string, and reset string.
5.
Click the Security tab. Enter the site password in the Site Password box.
Click File Access Password to create a password for the Site File.
Figure 3.3. Site Properties, Site tab
Figure 3.4. Site Properties, Comm tab
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 3.5. Site Properties, Security tab
24
System Configuration ~ Site Setup
Adding a PSR1212
You can add a PSR1212(s) to your site file by connecting to your site and using
G-Ware to automatically create icons for the detected units. Or, you can work offline
and manually add the unit(s) to the site file and connect to the site at a later time.
To open an existing site file, click the Open Site File button or select Open Site from
Figure 3.6. Open
Site File button
the File menu.
To auto-detect units
1.
Click the Connect button on the G-Ware toolbar or select Connect from the
Connect Menu.
Figure 3.7.
Connect button
2.
Choose Sync to Unit(s). G-Ware will automatically create icons for the new
units it detects on the network and place them in the Site pane. See Figure
3.11.
Figure 3.8. Connection choices
Note: When connecting to your site, you can choose to sync to Unit(s) or
Document. If you sync to the Unit(s), you will overwrite your G-Ware site file
with the current settings of the unit(s). If you sync to the Document, you will
overwrite the settings in your units with the settings you have saved in the site
file. Choosing to sync to Document will also create icons for any new units.
To manually add units
1.
If you are working offline, click the Add button on the G-Ware toolbar. This
opens the Add Unit window.
Figure 3.9. Add Unit
to Current Site
Figure 3.10. Add Unit window
2.
Select the PSR1212 icon and click Add.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
25
System Configuration ~ Site Setup
Configuring Unit Properties
Using the Unit Properties window, you can configure the unit’s communication and
security properties in addition to general unit properties such as name and type. The
Unit Properties window automatically opens when you manually add a unit to the
site. You can also right-click the unit icon in the site pane and click Unit Properties.
To configure Unit Properties
1.
Figure 3.11. Unit icons in Site
Pane with Unit menu displayed
Type a descriptive Unit Name in the space provided. The Unit Identification
and Firmware Version will be supplied by the unit when a connection is made.
2.
If you have already established a connection with the site, the Device
ID will be assigned. Otherwise, select the Device ID that matches the ID you
assigned the unit via the front-panel LCD menu.
Device IDs ensure the software will sync up with the proper unit when there
are multiple PSR1212s on a network.
3.
Select the Unit Type (default is slave). See page 12 for more information.
4.
Select an input, output, or processing channel to be the Default Meter on
the front panel meter LED when a channel is not specifically selected.
5.
Select the Meter Refresh Rate, which determines how quickly the
Figure 3.12. Unit Properties, General tab
PSR1212 updates meter information (default is 100ms; range is
50–1000ms).
6.
Click the Comm tab. The Baud Rate and Flow Control settings are supplied
by the unit when a connection is made. These settings are changed using the
Site Properties window (see page 23).
7.
Set the Serial Echo (default On) and the Serial Mode (default Text).
Serial Echo echos back commands sent over the PSR1212 network. The
serial mode determines the format in which the commands return—
text or
binary. The mode defaults to Binary when G-Ware is connected and to Text
when disconnected. Contact technical support for instructions on using Binary
mode.
Figure 3.13. Unit Properties Comm tab
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
26
System Configuration ~ Site Setup
8.
If a modem is connected to the PSR1212 unit, select Use Modem and enter
the initialization string. Click OK; the PSR1212 will initialize the modem.
9.
Click the Security tab. Create a modem password. The password will be
required before control of the system through remote modem access is
allowed. The default modem password is a carriage return.
10. Preset/Macro Password enables you to password protect your individual
presets and macros. To create a password, click Preset/Macro Password.
Creating a Preset/Macro Password does not automatically lock all presets or
macros. Presets are locked in the Preset Configuration Mode. See page 54
for more information. Macros are locked in the Macro Editor. Presets and
Figure 3.14. Unit Properties Security tab
Macros that are locked do not require the password to be run. However, the
password is required to make changes.
11. Select the Front Panel Lock Mode.
•
Unlock Panel leaves the front panel controls unlocked.
•
Lock Panel locks the front panel immediately.
•
Lock When Timeout locks the front panel after it is inactive for the
specified number of minutes. The range is from 0–15 minutes; 5
minutes is the default.
When locked, the front panel can be accessed only after entering the proper
passcode (sequence of button presses) or by unlocking the panel using
G-Ware.
12. To create a passcode for the front panel, click Clear to clear the default
sequence. Then click any sequence of the five front panel buttons. Your
choices will be displayed in the column on the right. When you are finished,
click OK to enable your selections.
You will need to repeat these steps for all PSR1212 units on your network.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
27
System Configuration ~ G-Ware Screens
G-Ware Screens
G-Ware has three modes: Configuration, Preset, and Macro Recorder. Configuration
is used to configure the unit and is the default mode. The Preset and Macro modes
are discussed in Chapter 4: Advanced Configuration. You can switch between modes
by clicking on the corresponding toolbar button. The current mode is displayed on the
status bar.
There are two main configuration screens, the Flow Screen and the Matrix
Screen. All unit configuration and audio routing is accessed through these screens.
Flow Screen
Tool
bar
M enus
Site pane
Flow Screen
Stat
usbar
Figure 3.16. G-Ware Flow Screen
The G-Ware Flow Screen is the main access window for G-Ware’s features and
functions. Using the menus and toolbar at the top of the screen, you can access
general configuration windows. Unit specific configurations are accessed through the
buttons and labels on the Flow Screen itself. If you have multiple units, click on the
unit icon in the Site pane to access that particular unit’s Flow Screen.
The Flow Screen shows a detailed block diagram of the path of the audio
signal, presenting a graphical explanation of each stage of audio processing. Mic
and line inputs, outputs, expansion buses, and processing block configuration
windows can all be accessed from this screen. The PSR1212 Flow Screen has
seven icons and buttons at the bottom of the Flow Screen which open the following
unit programs: Remote Builder, Gating Control, Signal Generator, Preset Mode,
Macro Editor, Meters, and GPIO Builder.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 3.15.
Configuration, Preset,
and Macro toolbar
buttons.
28
System Configuration ~ G-Ware Screens
Copying and pasting settings
G-Ware has shortcut menus which appear when you right-click a selection or
program window in G-Ware. These shortcut menus provide quick access to options
such as Print, Copy, and Paste that pertain only to that selection or screen region.
Figure 3.17. Unit
shortcut menu
Using the Copy and Paste commands, you can copy and paste unit data such as a
single setting or the entire unit’s settings depending on which window you are in. For
example, if you are in the Inputs 1–8 window, using the shortcut menu will allow you
to copy and paste all of the input settings to other inputs. You can also use keyboard
shortcuts (Ctrl+C and Ctrl+V) to copy and paste settings. If you want to apply all
settings of a selected input to the rest of the inputs, select Apply to All.
Figure 3.18. Inputs 1–8
shortcut menu
Figure 3.19.
Safety Mute
Safety Mute
The Safety Mute feature in G-Ware enables you to mute all outputs if feedback or
audio problems occur during the configuration process. To use Safety Mute, click the
Safety Mute button on the G-Ware toolbar. Then find and correct the cause of the
problem. Click the Safety Mute button again to unmute the outputs.
Status bar
There are two status lights at the bottom of the G-Ware window representing the
unit and the site. The lights illuminate in various colors to indicate current status.
•
Solid green. The item being configured is synchronized with the hardware.
•
Solid red. The information being configured is saved in the software offline.
•
Flashing red. The information is not saved or there is no hardware
connection.
•
Solid yellow. Communications are pending.
•
Flashing yellow. There is a communication error. In this instance, you should
disconnect from the unit and reconnect. The Message Log will indicate the error
that occurred. See page 73 for more information.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
29
System Configuration ~ G-Ware Screens
Matrix Screen
The Matrix Screen is used to route audio to one or more destinations (outputs,
expansion bus, or processing). Any number of connections to outputs can be made in
the matrix. The Matrix Screen can also be used to access the Input, Output, and
Processing configuration windows by clicking on the buttons along the top and left
sides of the routing matrix.
Toolbar
Menus
Labels
Site pane
Matrix Screen
Status bar
Figure 3.20. G-Ware Matrix Screen
A colored cell in the routing matrix marks the intersection or cross point of
the routing from input to output. The color of the cross point cell identifies the
input type: yellow = gated mic input, blue = non-gated mic input, and green = all
other inputs. The amount of attenuation is also shown in the cross point cell. Black
cell are restricted routing paths which prevent E-bus and Processing channels from
being routed back to themselves.
The numbers and letters along the top and left side of the matrix show the
cross point coordinates. The input number or letter and the output number or letter
will be highlighted blue for the selected cross point.
All inputs and outputs are labeled to make it easier to identify channels.
Clicking on a label will open a labels window where you can change the channel
labels.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
30
System Configuration ~ Audio Routing
Audio Routing
Audio is routed in the Matrix Screen (see Figure 3.20 on previous page). To access
the Matrix Screen, click on the Matrix button on the Flow Screen. To return to the
Flow Screen, click the Flow Screen button.
The PSR1212 routing matrix has 32 possible input sources and 32 output
destinations, with level control at each cross point. Any input or combination of
inputs can be routed to any output or any combination of outputs. To clear the
matrix, click the Clear Matrix button located above the Routing Key.
To route an input, click in the routing matrix at the intersection between the
Figure 3.21. Matrix Routing
input and the output. A mic input can be designated as gated (yellow) or nongated (blue) by clicking repeatedly in the cross point. All other input cross points
If you click the Clear
Matrix button, you will
clear all cross points in
the routing matrix.
-
will be colored green.
Expansion bus O–Z routing
Audio on any PSR unit in the E-bus network can be placed on the bus or taken off
the bus and routed to any destination within the unit. The PSR1212 has 12 digital
mix-minus buses:
•
O–R buses are defaulted as the mic mix buses and can communicate the
NOM count. Gated mics are default routed to the O bus.
•
S–Z buses are defaulted as the auxiliary mix buses. They are used to carry
auxiliary audio such as that from VCRs and CD players. These buses are
used as mic mix buses when NOM count is not required.
Process A–H routing
There are eight processing blocks on the PSR1212 (Processing A–H). With these
processing channels, you can apply filters, EQ, or other processing settings to an
input or a group of inputs which can then be routed to a single output or group of
outputs. See page 47 for more information on processing settings.
Cross point attenuation
Right-click on a cross point to open the Cross Point shortcut menu. Click Cross Point
Enter to open the Cross Point Attenuation Dial window.
Figure 3.22. Cross Point
shortcut menu
Click the s and tbuttons or click on the green indicator and rotate the dial
with the mouse to adjust the attenuation to the desired level (or enter the
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
31
System Configuration ~ Audio Routing
numerical value directly in the window). The attenuation range is from 0 to 60dB. Click Close to exit. Note that the level control you have selected for the
cross point is indicated numerically in the cross point cell.
The Cross Point shortcut menu also allows you to copy and paste the current
Cross Point configuration, including attenuation, to other cross points. You can
copy a single cell or the entire matrix using the shortcut menu options. To copy
and paste a cross point to multiple cross points, press Ctrl+C to copy (or rightmouse click). Then press Ctrl+V while holding down the left-mouse button and
drag the mouse over the cross points to which you want to copy the settings.
Matrix report
When you finish audio routing, you can print a detailed report of the matrix using
the Print Matrix option on the shortcut menu (see Figure 3.22).
The Print Matrix Report window displays all matrix routing and cross point
information. Click the Print icon button to print the report.
Figure 3.24. Matrix Report window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 3.23. Cross Point window
32
System Configuration ~ Inputs and Outputs
Inputs and Outputs
-
Inputs 1–8 accept either
microphone (-55, -25dB)
or line level (0dB)
Inputs 1–8
To open the Inputs 1–8 configuration window, click the Inputs 1–8 button on the
Flow Screen. The In 1–8 button on the Matrix Screen will also open this window.
These inputs are balanced and support both mic and line levels.
Figure 3.25. Inputs 1–8 configuration window
To select an input channel, click a blank area in the input pane. If you click
on the input label, a secondary window will open allowing you to rename the
input. The background color for the selected input channel will be light gray. The
many configurable properties of mic inputs are defined in this section.
Mute
Mute mutes the input channel. The light on the button illuminates red when Mute is
activated. Default is Off (unmuted).
AGC
AGC toggles on and off the automatic gain control. AGC keeps softer and louder
input audio to a consistent level. It does this by attempting to adjust the signal to a
fixed +4dB target level. If the signal level and the +4dB target level both fall
within the AGC’s 12dB range, the AGC achieves the +4dB target level. If the signal
level is more than 12dB away from the +4dB target level, the AGC sets the level
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
12dB closer to the target. AGC occurs after the gain and filter settings in the audio
signal path. AGC default is Off.
P Pwr (Phantom Power)
Phantom Power toggles the phantom power on and off. Phantom power is an
auxiliary power source to power certain types of microphones. The PSR1212’s
phantom power voltage is 24VDC. Default is On.
Filters
Figure 3.26. Inputs 1–8 Filters window
The Filter button on the selected input in the Inputs 1–8 window opens the Filter
Graph setup window. Each mic/line input has four configurable filters that can be
used as filters or equalizers. By default, they are not enabled and the filter types are
not defined. Below is a description of each feature in the window.
Active Filter
Active Filter selects among filters on the graph. Note that no filters exist until you
click Add Filter (see Figure 3.26).
Type
Use the Type list to select from the following input filters: All Pass, High Pass, Low
Pass, Notch, and PEQ. G-Ware features other filters which are configured in the
Processing section of the software (see page 47).
•
All Pass. Frequency range is 20Hz to 20kHz with resolution to 1Hz or four
places (whichever is larger).
•
High Pass. Selectable frequency cutoff is 20Hz to 20kHz, in 1Hz
increments. Rolloff is 12dB/octave. Level is fixed at 0dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
33
34
System Configuration ~ Inputs and Outputs
•
Low Pass. Selectable frequency cutoff is 20Hz to 20kHz in 1Hz increments.
Rolloff is 12dB/octave. Level is fixed at 0dB.
•
Notch. Center frequency range is 20Hz to 20kHz with resolution to 1Hz or
four places (whichever is larger). Bandwidth is from .05 to 5 octaves in .01
octave increments. Level is fixed at -80dB.
•
PEQ (parametric equalizer). Center frequency range is 20Hz to 20kHz
with resolution to 1Hz or 4 places (whichever is larger). Bandwidth is .05
to 5 octaves in .01 octave increments. Level range is -15 to +15dB in
0.5dB increments.
Frequency. Use Frequency to select the center frequency (in Hertz) for the filter
you are configuring. Range is from 20Hz to 20kHz. Default is 1kHz.
Gain. Gain adjusts the gain value from -18 to 18dB, in .5dB steps. Default is 0dB.
Q, or Quality factor. Q, or Quality factor, selects the ratio of the center frequency
divided by the bandwidth. Q reflects an inverse relationship to the bandwidth, and
adjusts from .02:1 to 40:1 on the PSR1212.
Bandwidth. Bandwidth establishes the difference between the upper and lower
points of a filter’s audio passband.
Bypass. The Bypass box, when selected, bypasses the selected filter.
Phase. Phase generates—on the graph—the phase relationship of the graphed
frequency response.
Bypass All. Bypass All bypasses all filters.
Add Filter. Add Filter adds a filter to the graph, centered at 1kHz and 0dB.
Remove Filter. Remove Filter removes the selected filter from the graph.
Table View
Table View toggles between the Graph and the Table views of the Inputs 1-8 Filter
window. The Table view displays the selected filter settings in table format. You can
configure filters from this view as well as in the graph view.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
35
System Configuration ~ Inputs and Outputs
Figure 3.27. Filter Graph window, table view
To configure filters
1.
In either the graph or table view, select the filter type from the Type list.
Note that the configurable filter parameters displayed depend on the
selected filter type.
2.
Click Add Filter to add a filter to the graph or table.
3.
Configure filter parameters using the previously described lists. If you are
using the graph view, you can click on the node and drag it to the location
you desire on the graph.
4.
Click Close to exit.
Gate
The PSR1212 has unique gating parameters which control microphone activation.
The Gate button on the selected input in Inputs 1–8 window opens the Gate
configuration window where you can establish the gating parameters for the input.
Activation
There are three mic activation settings: Auto Gate, Manual On, and Manual Off.
•
Auto Gate determines mic gating based on the input level and gating settings
for the gating group the input is assigned to. It contributes to and is affected
by all gating group settings such as NOM, chairman override, etc.
•
Manual On activates the mic, provided it does not exceed max NOM
requirements of the gating group that the input is assigned to. It is included in
the NOM count.
•
Manual Off deactivates the mic.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 3.28. Gate window
36
System Configuration ~ Inputs and Outputs
Chairman Override
Chairman Override provides gating priority for this mic input over any other mic
input within the same gating control (mixer) groups. When a mic with Chairman
Override enabled gates on, all mics which don’t have Chairman Override enabled will
gate off. Default is off.
Adaptive Ambient
Adaptive Ambient adjusts the ambient reference level as noise and room conditions
change. When adaptive ambient is on, the mic channel monitors the ambient noise
level on the input and adjusts the ambient level reference automatically. This means
that the gate threshold level automatically increases or decreases based on background noise. If Adaptive Ambient is turned off, the input will use the fixed ambient
level specified in the Ambient Level box as its gating reference. Default is on.
PA Adaptive Mode
PA Adaptive Mode uses loudspeaker audio level on a specified output as the new
ambient level when audio is present at the power amplifier. This prevents
loudspeaker audio from gating on the mic, while still allowing people in the room to
gate on microphones as they speak—
provided that their voices are louder than the
loudspeaker audio. For example, you might decide to play background music from a
CD player during a presentation. PA Adapt Mode allows you to use the output routed
from the CD player as the ambient reference to prevent the CD player’s audio from
gating on microphones. An output must be specified as the PA Adaptive Reference
for each mic in the system. Default is on.
Gate Ratio
Gate Ratio specifies how much louder the audio level must be above the ambient
level before the channel gates on. The gate ratio range is from 0 to 50dB. Default is
15dB.
Hold Time
Hold Time determines how long the channel stays gated on after the audio is below
the threshold. The hold time range is from .1 to 8.0 seconds. Default is .3 seconds.
Off Attenuation
Off Attenuation sets the amount of level reduction applied to a channel when it is
gated off. The range is from 0 to 50dB. Default is 12dB.
Ambient Level
Ambient Level is available only if the Adaptive Ambient feature isn’t enabled. Use
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
Figure 3.29. PSR1212 automixing gate functions
Ambient Level if you want to specify a fixed reference point rather than one that
adjusts for background noise. The range is from -80 to 0dB. Default is Off.
Decay Rate
Decay Rate determines how fast a channel gates off after the hold time expires.
Default is Medium.
PA Adapt and AEC Reference
When using the PA Adaptive mode, the output that carries this information, i.e. the
reference output, must be defined. Select the reference output from the PA Adapt
and AEC Reference list. Any one of the 12 outputs, four expansion bus references, or
four virtual references can be selected.
If you select an expansion bus reference, the Define PA Adapt/AEC
Expansion Bus Ref window opens so you can identify which expansion bus output you
want to use as the PA reference. You can also open this window from the toolbar.
Figure 3.30. PA Adapt/AEC
window and toolbar button
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
37
38
System Configuration ~ Inputs and Outputs
If you select a virtual reference, the Virtual Reference window will open. You can
also open this window from the G-Ware toolbar.
Figure 3.31.
Virtual Reference
toolbar button
Figure 3.32. Virtual Reference window.
Use this window to select which signals will be included in each of the four
Virtual Reference points. The routing matrix portion of this window cannot be
edited. Virtual references are used when you need to reference multiple outputs.
For example, if you have multiple zones in a boardroom or large meeting room,
you might want the mics to reference two zones. By using a virtual reference, PA
Adapt will be able to reference both signals. This means you don’t need to use a
dedicated output to combine signals.
To create a virtual reference
1.
Select the input signals you want included in each virtual reference by
clicking the cross points.
2.
Because AEC requires a physical output reference to track output gain
changes, you need to select an output reference for AEC to function properly
with a virtual reference. Use the lists at the bottom of the window to select
which output you want AEC to use to track gain changes.
3.
Click Close to exit the window.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
39
System Configuration ~ Inputs and Outputs
Gating Group Select
In addition to specifying gating characteristics for each mic input, you can assign the
inputs to a gating group for greater flexibility and control. When inputs are
assigned to a gating group, the gating information from the inputs is used to
Figure 3.33. Gating
Group Select pane
control how the entire mixer behaves.
The PSR1212 features four internal gating groups (Internal 1–4) and four
global gating groups across the expansion bus (Global A–D). Microphones can be
used in only one gating group at a time. If an input is not assigned to a gating
group, that mic’s gate properties are independent and have no effect on any other
gating group. When gating groups span two or more units (global gating groups),
the settings must be the same for each unit attached to the global gating group.
Mic inputs are routed to Global Group A by default.
To assign a gating group
•
Select the Internal or Global group the mic input will belong to or select
None.
To configure gating group settings
1.
Click the Gating Control button on the toolbar. This opens the Gating
Controls window.
Figure 3.34. Gating Control button
Figure 3.35. Gating Controls window
2.
Select the Max # of Mics (default is 4).
This sets the maximum number of microphones that can be gated on at any
one time within a gating group. For internal groups, the maximum number
of mics can be from 1 to 8. For global groups the maximum number of mics
will vary depending on how many mic inputs are assigned to the gating
group (up to 64). You can also select All for the global groups—
which means
all mics could gate on.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
40
System Configuration ~ Inputs and Outputs
3.
Leave 1st Mic Priority selected (default) to enable this feature; otherwise,
clear the selection to disable it. ClearOne recommends leaving this setting
on.
This setting helps maintain maximum audio intelligibility by allowing only
one mic to gate on to a participant’s voice. 1st Mic Priority allows more
than one microphone to be activated at the same time—
it simply restricts
mics from gating on to the same audio source. It does this by determining
the audio level received by all mics when the first mic is gated on. This
audio level is then used as the ambient level for the gating group. If this
feature is disabled, usually two or more microphones gate on when only one
person speaks.
4.
Select last-mic operation from the Last Mic Mode list. There are two
options for Internal groups: Last On and Off. If you are configuring Global
groups, you can select from the mic inputs assigned to the Global group in
addition to Last On and Off.
Last On leaves the mic that was activated last full on until another mic input
is gated on. The Input setting allows you to select which mic input the
PSR1212 leaves on when all mics gate off. In a boardroom or meeting
room application, this feature can be used to specify the chairperson’s mic
as the last mic on. If Off is selected, all mics will gate off when no audio is
present.
5.
Click the Gating Group label to change the group names.
Gain
The Coarse and Fine sliders on the selected input on the Inputs 1–8 window are used
to match the level settings for microphone inputs and to adjust input volume level.
•
Set the Coarse gain to 55dB for a mic input, 25dB for active equipment that
requires an input between mic and line level, or 0dB for a line level input.
•
Use the Fine gain slider to adjust input volume level. You can also enter the
level directly in the 0.0dB box.
Max adju
Min/Max limits
Use the yellow and blue upper and lower limit arrows on the Fine gain scale to
create minimum and maximum gain level limits. These limits apply only when using
M in adju
relative gain commands; absolute gain commands can exceed the min and max
limits. Min/Max limits apply to all serially connected control devices and prevent
Figure 3.36. Gain
adjustment
users from adjusting levels beyond the min/max levels, provided relative gain
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
41
System Configuration ~ Inputs and Outputs
commands are used.
Optimizing input gain structure
How you adjust an input’s gain directly affects sound quality. The optimal input gain
setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the input level properly, place a signal on the input at the maximum
level it will generate. Adjust the input gain until the peak level of the input, as
shown on the Input meter, just begins to enter the red (clipping) zone, then reduce
the gain slightly until peaks no longer climb into the red zone. This setting will
ensure that the PSR1212 maximizes the signal-to-noise ratio without clipping the
signal.
Meters
There are four meters on each mic/line input to assist with setup and level control.
Select the meter check box to enable the meter. All input meters are peak-level.
Pre Gain
Pre Gain meter indicates the input’s level before gain adjustments. Meter range is
from -85 to -35dB when 55dB gain is selected; -55 to -5dB when 25dB gain is
selected; and -65 to 20dB when 0dB gain is selected.
Post Gain
Post Gain meter shows the input’s level after gain adjustments have been made.
Meter range is from -30 to +20dB.
Post Processing
Post Processing meter indicates the level at the gating point after the signal has
passed through input processing. It reflects the post-AGC signal. Meter range is
from -30 to +20dB.
Post Gating
Post Gating meter shows audio level after it has passed through the gating
parameters. Meter range is from -30 to +20dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 3.37. Mic
input meters
42
System Configuration ~ Inputs and Outputs
Inputs 9–12
The PSR1212 supports four line level only inputs for auxiliary audio sources such as
VCRs and CD players. To open the Inputs 9–12 configuration window, click the
Inputs 9–12 button on the Flow Screen. The In 9–12 button on the Matrix Screen
will also open this window. These non-gated inputs are balanced. The nominal input
level is 0dBu.
Figure 3.38. Inputs 9–12 Configuration window
To select an input channel, click a blank area in the input pane. If you click
on the input label, a secondary window will open allowing you to rename the
input. The background color for the selected input channel will be light gray. The
configurable properties of these inputs are defined in this section.
Mute
Mute mutes the input channel. The light on the button illuminates red when Mute is
activated. Default is off (unmuted).
AGC
AGC toggles on and off the automatic gain control. AGC keeps softer and louder
input audio to a consistent level. The button light illuminates green when AGC is
enabled.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
43
System Configuration ~ Inputs and Outputs
Gain
The Gain slider on the selected input in the Inputs 9–12 window is used to adjust
input volume level.
•
Max adju
Use the Gain slider to adjust input volume level. You can also enter the level
directly in the decibel box below the gain scale.
M in adju
Min/Max limits
Use the yellow and blue upper and lower limit arrows on the Gain scale to create
Figure 3.39. Gain adjust
on line level input
minimum and maximum gain level limits. These limits apply only when using relative
gain commands; absolute gain commands can exceed the min and max limits.
Min/Max limits apply to all serially connected control devices and prevent users from
adjusting levels beyond the min/max levels, provided relative gain commands are
used.
Optimizing input gain structure
How you adjust an input’s gain directly affects sound quality. The optimal input gain
setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the input level properly, place a signal on the input at the maximum
level it will generate. Adjust the input gain until the peak level of the input, as
shown on the Post Gain meter, just begins to enter the red (clipping) zone, then
reduce the gain slightly until peaks no longer climb into the red zone. This setting
will ensure that the PSR1212 maximizes the signal-to-noise ratio without clipping
the signal.
Meters
Pre Gain
Pre Gain meter indicates the input’s level before gain adjustments have been made.
Meter range is from -30 to +20dB.
Post Gain
Post Gain meter shows the input’s level after gain adjustments have been made.
Meter range is from -30 to +20dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 3.40. Gain
meters
44
System Configuration ~ Inputs and Outputs
Outputs 1–12
The PSR1212 has 12 line level outputs for sending audio to recorders or amplifiers.
To open the Outputs 1–12 configuration window, click the Outputs 1–12 button on
the Flow Screen. The Outputs 1–12 button on the Matrix Screen will also open this
window.
Figure 3.41. Outputs 1-12 configuration window
These line level outputs are balanced. The nominal output level is 0dBu. The
outputs can adjust from -65 to 20dBu.
To select an output channel, click a blank area in the output pane. If you click
on the output label, a secondary window will open allowing you to rename the
output. The background color for the selected output channel will be light gray.
The configurable properties of these outputs are defined in this section.
Mute
Mute mutes the output channel. The light on the button illuminates red when Mute is
activated. Default is off (unmuted).
NOM
NOM (constant gain) maintains a constant output level as inputs routed to the output
are gated on and off. The PSR1212 reduces the output gain (at the output) for mics
based on the number of mics gated on and routed to that output. When using NOM
over the expansion bus, only the first four audio channels (O, P, Q, and R) support
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
45
System Configuration ~ Inputs and Outputs
passing NOM information. Enable NOM if you want to place this output in a
constant gain mode. Default is on. When enabled, the NOM button light
illuminates green.
Gain
The Gain slider on the selected output in the Outputs 1–12 window is used to adjust
output gain level.
•
Use the Gain slider to adjust output volume level. You can also enter the level
Max adjust
M in adjust
directly in the decibel box. If you select any level below -60dB, the signal will
be muted. The Level meter, when enabled, shows the signal level when a signal
is present.
Min/Max limits
Use the yellow and blue upper and lower limit arrows on the Gain scale to create
minimum and maximum gain level limits. These limits apply only when using relative
gain commands; absolute gain commands can exceed the min and max limits.
Min/Max limits apply to all serially connected control devices and prevent users from
adjusting levels beyond the min/max levels, provided relative gain commands are
used.
Optimizing output gain structure
How you adjust an output’s gain directly affects sound quality. The optimal output
gain setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the output level properly, place a signal on the output at the
maximum level it will generate. Adjust the output gain until the peak level of the
input, as shown on the Level meter, just begins to enter the red (clipping) zone,
then reduce the gain slightly until peaks no longer climb into the red zone. This
setting will ensure that the PSR1212 maximizes the signal-to-noise ratio without
clipping the signal.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 3.42.
Output gain adjust
46
System Configuration ~ Expansion Buses
Expansion Buses
Routing of audio to the
expansion buses is done
in the Matrix Screen.
See page 30. For information on
setting up an expansion bus
network, see page 11.
-
From Expansion Bus O–Z
Click the From Expansion Bus O–Z button on the Flow Screen to open the From
Expansion Bus Labels window. You can also access this window from the Matrix
Screen.
Figure 3.43. From Expansion Bus Labels window
•
Enter the names you want to use for each expansion bus, then click OK to
save the information and close the window.
To Expansion Bus O–Z
Click the To Expansion Bus O–Z button on the Flow Screen to open the To
Expansion Bus Labels window. You can also access this window from the Matrix
Screen.
Figure 3.44. To Expansion Bus Labels window
•
Enter the names you want to use for each expansion bus, then click OK to
save the information and close the window.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
Processing
Processing A–H
There are eight processing blocks in the PSR1212, each with filters, compressors, and
delay to provide pinpoint audio configurations. To open the Processing configuration
window, click the Processing A–H button on the Flow Screen. The To and From
Processing buttons on the Matrix Screen will also open this window.
Figure 3.45. Processing window
To select a processing block, click a blank area in the Process pane. If you
click on the Process label, a secondary window will open, allowing you to rename
the processing block. The background color for the selected processor will be light
gray. The configurable properties of these processors are defined in this section.
Mute
Mute mutes the processor. The light on the button illuminates red when Mute is
activated. Default is off (unmuted).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
47
48
System Configuration ~ Processing
Cmprs (compressor)
Cmprs opens the Compressor Setup window (see Figure 3.46). With the compressor
you can change the gain transfer characteristics of the signal path and control the
dynamics of a signal.
When the signal exceeds the threshold level, gain reduction occurs at the rate
specified by the reduction ratio. The attack time determines how aggressively the
compressor reacts to increases in level. The release time controls how aggressively
the compressor reacts to reductions in level. Select the Enable Compressor check
box to activate the compressor.
Figure 3.46. Compressor Setup window
Group
Use the slider to assign this compressor to a compressor group. The default is None.
Compressors and compressor groups can be
established only within
the
PSR1212
unit
being
configured, i.e., they cannot be
configured from a single point
across multiple units.
-
When you assign a compressor to a compressor group—
such as a group of three,
configured for bass, midrange, and treble—
the compressors will monitor each
other. When one compressor channel compresses, all compressors in the group
compress together. When configured properly, this results in a smooth audio
response throughout the frequency range, with no bass, midrange, or treble
dropouts. A given compressor group must be configured for a single PSR1212
unit; a group cannot use compressors from multiple PSR1212 units.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
Post Compressor Gain Adjust the compressor gain with the gain slider or by using
the s and tbuttons. The graph reflects the input/output decibel levels with the gain
setting you select.
Threshold Threshold determines the RMS level at which the compressor begins to
operate. The range is from -30 to +20dBu. Default is 0dBu.
Ratio Ratio changes the rate of compression applied to the input signal as the
signal exceeds the threshold level. The range is 1:1 to 1:20. Default is 1:1.
Attack Attack determines how quickly compression is enabled. It is calibrated in
milliseconds. The range is 0 to 100ms in .5ms steps. Default is 10ms.
Release Release determines how quickly compression is disabled. The range is
100ms to 2 seconds, in 5ms increments. Default is 500ms.
Input meter This peak meter shows the level of the signal as it enters the
compressor.
Compression meter This peak meter shows the instantaneous compression value
at a given time.
Filters
The Filter button on the selected Processing channel opens the Processing Filters
window. Here, you can configure all filters available in G-Ware: All Pass, Bessel,
Butterworth, CD Horn, High Pass, High Shelving, Linkwitz-Riley, Low Pass, Low
Shelving, Notch, and PEQ.
Figure 3.47. Processing Filters window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
49
50
System Configuration ~ Processing
The frequency response and phase vs frequency of the total transfer function
of all filters is displayed in the window. Each filter can be disabled without
affecting the filter settings. All filters can also be disabled using a single
command. By default, they are not enabled and the filter types are not defined. Below
is a description of each feature in the window.
Active Filter
The Active Filter displays the filter that is applied to the processing channel.
Type
Select the filter type from the Type list. Note that the configurable filter
parameters displayed depend on the selected filter type. You can use these
parameters to customize the filter, or use the mouse to click and drag the node on
the graph to a location that reflects the changes you want to make.
You can continue to add filters to the graph, and track their relationships to
each other to design a system with the sound characteristics necessary for good
audio.
Phase
Phase plots the phase response of the frequency response of the selected filter.
Bypass
Bypass All bypasses all filters.
Add Filter
Add Filter adds a filter to the graph.
Remove Filter
This removes the selected filter from the graph.
Table View
Table View toggles between the graph view and the table view. The table view allows
you to configure filters in a table format rather than on the graph, and provides an
easy way to check filter status.
Processing Channels
The Processing Channels section allows you to display the graphs of various
processing channels together, so you can view and easily modify filter and equalizer
settings throughout the frequency range. Click the respective letter to place a
processor in the graph. Click the Active processor you want to modify; it appears in
bold on the graph.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
51
System Configuration ~ Processing
Figure 3.48. Low/Mid/High Loudspeaker Driver configuration
Refer to the figure above. Note that as you create filters across several
processing channels, you can observe their crossover points and general shape of
the frequency response. In this case, several Linkwitz-Riley filters are being
created across three processing channels to establish a balanced frequency
response from low-frequency, midrange, and high-frequency transducers.
Delay
Click Delay to open the Delay configuration window. Delay calibrates the amount of
signal delay introduced, based on the length (the distance between the source and
audience) and temperature you enter.
-
If you don’t want delay
added to the signal,
select the Bypass Delay
box.
Figure 3.49. Delay window
For example, different speaker drivers within a speaker enclosure might be
located different distances from the listening area because of design constraints
within the box. You can set up to 500ms of delay.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
The Calculated Delay
reading reflects any
changes you make in the
distance and temperature fields.
-
52
System Configuration ~ Processing
Introducing an appropriate amount of delay to the forward-mounted driver(s)
re-establishes the acoustical alignment necessary for proper sound imaging in a
room. The same principle of introducing delay applies to separate speaker
enclosures located various distances from the listening area.
Other types of delay to consider when establishing delay parameters are
delays which occur naturally as a result of processing operations within the
PSR1212. Propagation delay is an example. This delay is caused by operations
such as the conversion of the signal between analog and digital formats.
When you are finished making changes in the Delay window, click Close to
return to the Processor window.
Gain
Gain establishes the gain level for this channel. Select a level between -65 and
20dB. If you select any level below -60dB, the signal will be muted. The Process
meter, when enabled, shows the signal level when a signal is present.
Min/Max limits
Use the yellow and blue upper and lower limit arrows on the Gain scale to create
minimum and maximum gain level limits. These limits apply only when using relative
Figure 3.50. Process
gain adjust and meter
gain commands; absolute gain commands can exceed the min and max limits.
Min/Max limits apply to all serially connected control devices and prevent users from
adjusting levels beyond the min/max levels, provided relative gain commands are
used.
Optimizing process gain structure
How you adjust the processing gain directly affects sound quality. The optimal gain
setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the processing gain level properly, place a signal on the output at
the maximum level it will generate. Adjust the gain until the peak level of the
input, as shown on the Process meter, just begins to enter the red (clipping) zone,
then reduce the gain slightly until peaks no longer climb into the red zone. This
setting will ensure that the PSR1212 maximizes the signal-to-noise ratio without
clipping the signal.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 4: Advanced
Configuration
Presets
Overview
For many audio conferencing applications, a great deal of system flexibility is needed
to meet the challenges presented by changing meeting or conference room
requirements. These requirements might include changes in muting, audio sources,
room orientation, or room combining. And ideally, these changes are made
instantaneously—
without interrupting or affecting any meetings in progress.
Using presets enables you to accommodate these changing room requirements
quickly and efficiently. When you create a preset, you are essentially creating a
single room configuration option. Presets can be programmed with a variety of
routing, level, gating, delay, filter, and compression settings to meet specific
application requirements. You can change every unit parameter or a select few
depending on your room needs. PSR1212 presets are unique in the sense that they
operate independently of other presets in the unit. When a preset is run, only the
selected inputs/outputs are changed—
all other settings in other presets remain
unchanged and are not reset. This means you can change audio routing and
configuration settings in a room without affecting settings in other rooms (such as
gain). You can create up to 32 presets for the PSR1212.
Presets can be executed in a variety of different ways including the Execute
Preset utility in G-Ware, the front panel controls of the PSR1212, RS-232
external control devices, RS-485 control devices (ClearOne Control Panel and
Presets are used only
within
the
local
PSR1212 unit. However,
if a preset is part of a macro, it
can be activated on a networked
PSR1212 unit.
-
XAP IR Remote), logic in/out, and contact closure. You can also create macros
which can run multiple presets. These options give you tremendous flexibility when
designing your installations and will be described in more detail in this chapter.
Creating Presets
Presets are created in G-Ware using the Preset mode. To switch to Preset Mode,
click the Preset Mode button on the toolbar or the Preset Mode button on the Flow
Screen. The Preset Mode window (see Figure 4.2) consists of the Preset
Configuration Pane (left side of the window), the G-Ware menus and toolbar
(although most options are not available because they do not apply to presets), and
the Preset Matrix Screen. There is no Flow Screen in Preset Mode since all
configurable settings can be accessed from the Matrix Screen.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 4.1. Preset Mode
toolbar button
54
Advanced Configuration ~ Presets
G-Ware Toolbar
G-Ware
Menus
Preset
Configuration
Pane
Preset
Matrix Screen
Status Bar
Figure 4.2. Preset Mode
Matrix Screen
The Matrix Screen in the Preset Mode is very similar to the Matrix Screen in
Configuration Mode. All Input, Output, and Processing windows can be accessed by
clicking on their respective buttons. You can also create custom labels by clicking on
the current labels.
The routing matrix is grayed out because no routing changes have been made.
When you click on the number or letter of an input, the row becomes active and
you can change the routing, gate status, and cross point attenuation. All
parameters for the selected input will be saved in the preset including routing.
Also, the parameters for any outputs with a cross point in the selected row will be
saved. Input rows that are not selected remain gray, or masked, and will not be
affected when the preset is run.
Preset Configuration pane
The Preset Configuration pane is used to create preset properties such as number,
name, and description as well as create custom preset controls, assign the preset to
a gating group, select macros, and configure virtual references.
Preset Selection. Use the Preset Selection list to assign a number to the preset
you are creating or to select an existing preset for editing.
Protected. Select the Protected check box to lock your preset. Locked presets are
indicated by a padlock icon. Presets that are locked do not require the password
to be run. However, the password is required to make changes to the preset. The
Figure 4.3. Preset Configuration pane
preset password is set in the Unit Properties window; see page 26.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
55
Advanced Configuration ~ Presets
Preset Description. Use the Preset Description box for entering information about
the preset. This description is stored in the site file, not the unit.
Preset Mask Control/Status B. With Preset Mask Control Status B you can
require an active high (H) or active low (L) contact on a control pin (1–19 odd
numbers) or combination of several contacts in order to run the preset.
A typical use for Preset Mask Control Status B is a room combining
Figure 4.4. Preset Mask
Control/Status B
application which uses automatic partitions with sensors or triggers which set the
pin to high (H) when the partition is closed and to low (L) when the partition is
open. For example, if pin 1 is connected to the first partition and Pin 3 is
connected to the second partition, then the Preset Mask Control Status B settings
shown in Figure 4.4 will activate the preset when the first partition is open and the
second partition is closed.
Change Preset Label. Change Preset Label opens the Change Preset Labels
window, where you can create a short description (label) for the preset.
Gating Controls. The Gating Controls button opens the Gating Controls window,
where you can select and configure gating groups for this preset. See page 39 for
more information about gating groups.
Macro Selection. The Macro Selection button opens the Preset Macros window,
where you assign specific macros to the preset you’re creating. Select the macros you
want to use with this preset, then click OK to save changes. See page 61 for more
information about creating macros.
GPIO Command Assignment. This opens the GPIO Builder window. With the
GPIO builder, you can configure pin assignments for the Control/Status port A. The
Use in Preset option is available only when you open the GPIO Builder from the
Preset mode and allows you to create customized pin assignments for each preset. If
you open GPIO Builder from the toolbar while in Configuration Mode, or from the
Flow Screen, you will not have the Use in Preset option. See Chapter 6: Control for
instructions on configuring pin assignments.
Remote Assignment. This opens the Remote Builder window. With the Remote
builder, you can configure the XAP IR Remote Control and the ClearOne Control
Panels. The Use in Preset selection box is available only when you open the Remote
Builder from the Preset Mode and allows you to create customized control for the
current preset. If you open Remote Builder from the toolbar while in Configuration
Mode, or from the Flow Screen, you will not have the Use in Preset option. See
Chapter 6: Control for instructions on configuring the XAP IR Remote.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 4.5. Preset Macros Window
56
Advanced Configuration ~ Presets
Virtual Reference. The Virtual Reference button opens the preset Virtual
Reference window. Using the Virtual Reference window, you can select which signals
will be used by the four Virtual Reference points in this preset configuration. The
only input rows which will be shown in this window are the input rows which are
active in the Preset Matrix Screen. The routing matrix (right pane) in this window is
read-only. Use the Virtual Reference portion of the window to select input channels
for Virtual Refs. 1–4.
Figure 4.6. Assigning virtual references to the preset
As with the standard (non-preset) Virtual Reference configuration, you will
need to select an output from the Output Level Tracking lists for each Virtual
Reference you configure. See page 38 for more information on creating Virtual
References.
Print Preset. Print Preset opens a Print Preview window and allows you to print a
copy of your preset settings. The preset must be saved before it can be printed.
Save Preset. Saves the current preset.
Clear Preset. Clears current preset settings.
Exit Preset. Returns you to the Matrix screen in the Configuration mode.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
To create a preset
1.
From the Preset Selection list, select the number of the preset you will be
configuring. Enter a description of the preset in the Preset Description box.
2.
If you want to password protect this preset, click Protected. See page 26
for information on creating the preset password.
3.
Configure the routing matrix and make cross point attenuation adjustments.
4.
Configure input, output, and processing channel settings as needed. See
Chapter 3: System Configuration for specific instructions on unit settings.
5.
Click Gating Controls to set up gating parameters for the preset.
6.
Make GPIO or Remote assignments as needed.
7.
Click Virtual Reference if you need to create Virtual References specific to
the preset.
8.
When you have finished configuring the preset, click Save Preset to save
the settings. Click Exit Preset to exit Preset Mode.
Storage space
In a realistic preset configuration scenario, it is highly unlikely that you would reach
the storage capacity of the unit. In the event that you exceed the preset storage
space, G-Ware will alert you when you try to save the preset. You will be asked to
reduce the number of cross point changes or the number of macros in the preset. As
a general rule, if you make cross point changes to three-fourths of the matrix, you
can establish a maximum of 128 nested macros for a given preset.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
57
58
Advanced Configuration ~ Presets
Running presets
Presets can be run from G-Ware or the front panel controls on the PSR1212. You
can also program external control devices (such as AMX or Crestron, ClearOne
Control Panels, XAP IR Remote, and GPIO devices) or use macros to run presets.
See Chapter 6: Control for more information on creating custom control.
To run a preset using G-Ware
Figure 4.7. Execute Preset
toolbar button
1.
Select the Execute Preset button on the G-Ware toolbar.
2.
Select the preset you want to execute from the Preset list.
Figure 4.8. Execute
Preset window
3.
Click Execute to run the preset and close the window.
To run a preset using front panel control
1.
From the System Menu, scroll to Select Preset and press Enter.
2.
Scroll to the preset number you want to run and press Enter.
Running multiple presets simultaneously
To run multiple presets at the same time, you need to create macros (see page 61). A
macro is a series of commands which can be executed from G-Ware or by using any
external control device. Typically you will create a macro for each configuration or
group of presets you want to run at the same time. This ability to run multiple
presets is critical in applications such as room combining. However, not only do you
need to be able to run multiple presets simultaneously, you also need to be able to
change presets without affecting other presets.
It is also possible to
assign states to presets
when creating Remote
Panel, serial, or GPIO control.
However, unless you create
macros, you will be able to run
only one preset at a time.
-
In order for this to happen, the system needs to know which presets have been
run and shouldn’t be rerun and which ones are ready to run. You supply the system
with this information by setting the state (or flag) of the preset when creating the
command line in the macro. The three options are:
0 = to set the state to off
1 = to execute the preset and set the state to on
2 = to execute the preset and set the state to off
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
59
Advanced Configuration ~ Presets
Figure 4.9. Assigning a state to a preset command in the Macro Editor
If a preset is flagged as “On,”nothing will happen when the preset is executed
again because the system knows it has already been run. This prevents any manual
adjustments that are made during the course of the meeting (gain, muting, etc.)
from being lost.
Room combining example
In the room combining scenario depicted in Figure 4.10, there are four possible
room configurations using six presets (P1–P6). In order to change configurations
without disturbing meetings in progress, a macro must be created for each
configuration that tells the system what to do with each of the six presets.
Figure 4.10. Room combining diagram
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
You can also create a
macro to set all preset
flags to 0 which ensures
all presets are ready to run again.
-
60
Advanced Configuration ~ Presets
The four macros (one for each configuration) are set up as follows:
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
When the room is in Configuration 1, running the Configuration 2 macro will
change the presets to the following states:
•
P1 does not change because the flag is already set (1)
•
P2 and P3 clear their states (0) so they can be run
•
P4 runs and sets its state to on (1) which prevents other presets from
rerunning it
•
P5 and P6 clear their states (0) so they can be run
When the room is in Configuration 3, running the Configuration 1 macro will change
the presets to the following states:
•
P1 and P2 run and set their state to on (1) which prevents other presets
from rerunning them
•
P3 does not change because the flag is already set (1)
•
P4, P5, and P6 clear their states (0) so they can be run
For more detailed information on creating macros, see the Macros section on the
next page.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
61
Advanced Configuration ~ Macros
Macros
A macro is a series of commands which can be run from G-Ware, the front panel
controls, or by using any external control device. Macros streamline the operation of
the PSR1212, allowing you to make quick configuration changes and, as previously
discussed, making it possible to execute multiple presets simultaneously (see pages
58–60). Macros can also contain commands that are executed on other XAP
units. See pages 95–96 for a list of commands which can be used in macros.
The PSR1212 is designed to support up to 255 macros, with an average of
150 command lines each. In the unlikely event that you exceed G-Ware’s capacity,
you will be notified with a warning that indicates the command line at which
memory is exceeded.
Creating macros
There are two ways to create macros in G-Ware: the Macro Recorder, which
records your onscreen selections, and the Macro Editor, which allows you to
directly create command lines. The Macro Editor is also used to edit macros
created using the Macro Recorder.
To create a macro using Macro Recorder
1.
Click the Macro Recorder button on the G-Ware toolbar. The Macro
Record window opens and the mode is changed to Macro on the status bar.
Figure 4.11. Macro
Recorder toolbar button
When you select an
existing macro as the
macro to record, the new
recording is appended to the end
of the existing macro.
-
Figure 4.13. Macro Record stop window
Figure 4.12. Macro Record start window
2.
Select the macro number from the Macro to Record list, then click Start.
3.
Make any routing and input/output configuration changes (such as gain
adjustments, mute, etc.) to be included in the macro. Make these changes
the same way you made changes in Configuration mode (see Chapter 3:
System Configuration for more information).
4.
Click Stop in the Macro Record window in the upper right-hand corner of
the screen. This stops the macro recording and opens the Macro Editor
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
62
Advanced Configuration ~ Macros
To create a macro using Macro Editor
1.
Click the Macro Editor button in the G-Ware toolbar to open the Macro
Editor.
Figure 4.14.
Macro Editor button
Figure 4.15. Macro Editor window
2.
Select the Macro (from 1 to 255) you are creating from the Macro list.
Numbers that are already assigned to macros will be marked with an
asterisk.
3.
Select the Protected check box to lock your macro. Locked macros are
indicated by a padlock icon. Macros that are locked do not require the
password to be run. However, the password is required to make changes to
the macro. The macro password is the same as the preset password and is set
in the Unit Properties window; see page 26.
Figure 4.16 Macro Name window
4.
Click Change Name to create a more descriptive name for the macro which
is displayed in addition to the macro number (limit 20 characters).
5.
Type any notes pertaining to the macro in the Macro Description box.
6.
Select the Device Type and ID from their respective lists.
7.
Select the Command from the Command list. When you select a command,
a description of it appears in the Command Description box.
8.
Select the command parameters from the argument lists. The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Macros
9.
Click Add to place the command into the macro. The command line now
appears in the command line table.
You can now create another command line for the macro or save the
completed macro.
Editing macros
With the Macro Editor, you can add, edit, or remove command lines in the macro. If
you used the Macro Recorder to create a macro, the Macro Editor opens
automatically. Otherwise, click the Macro Editor toolbar button.
To edit a macro
1.
Select the macro from the Macro list.
2.
Click Change Name to edit the macro label.
3.
Double-click the command line you want to edit. The Current Line Number
displays the selected command line.
4.
Make changes to the command or arguments by selecting options from the
drop-down lists.
5.
Click Replace to overwrite the old command line with the new changes.
6.
Click Save or Save As to save the macro.
To delete a macro
•
Click Clear Macro to delete the entire macro.
•
Click Delete to delete the selected command line.
To add or insert a command line
•
Click Add to place the current command line into the next available row in
the command line table.
•
Click Insert to insert the current command line into the row directly above
the currently selected command line in the table.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
63
64
Advanced Configuration ~ Macros
Running macros
Macros can be run from G-Ware or the front panel controls on the PSR1212. You
can also run a macro using external control devices (see Chapter 6: Control for more
information).
To run a macro using G-Ware
Figure 4.17. Run Macro
toolbar button
1.
Select the Run Macro button on the G-Ware toolbar.
2.
Select the macro from the Select Macro list.
Figure 4.18. Run Macro window
3.
Click Run to run the macro and close the window.
To run a macro using front panel control
1.
From the System Menu, scroll to Select Macro and press Enter.
2.
Scroll to the number of the macro you want to run and press Enter.
To run a macro using the Select panel or GPIO
•
Use the macro command. See Chapter 6: Control for more details.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 5: Operation
G-Ware features several tools designed to assist you as you install your PSR1212
Digital Matrix Mixer including Signal Generator, Document Compare, Print Reports,
Copy and Paste, and Message Log. G-Ware also provides Gate Views and Meters so
you can quickly monitor or troubleshoot your system. This chapter describes how to
use these utility programs and monitoring views in G-Ware.
Utilities
Signal Generator
Figure 5.1. Signal Generator Button
The Signal Generator window allows you to generate test audio signals to check
signal paths, gain settings, etc. The Signal Generator can generate pink noise, white
noise, and tone.
•
Pink Noise. Pink noise is an audio test signal containing all the frequencies
The Signal Generator window can
also be opened by selecting
Signal Generator from the Tools
menu.
in a given audio spectrum, with equal energy in each octave. Pink Noise is
the default signal.
•
White Noise. White noise is an audio test signal which is distributed evenly
throughout a given frequency range.
•
Tone. Selecting Tone activates the tone configuration portion of the window.
The tone is a sine wave with less than .03% distortion.
The test signals created by the signal generator are assigned to a particular input;
this allows you to verify the operation of the processor settings you have selected.
To use pink or white noise
1.
Select the PSR1212 Unit and Input Channel you want to use.
2.
Use the Amplitude control to select the amplitude (volume) of the signal you
want to use. The amplitude range is from -60 to +20dB. Default is 0dB.
3.
Select Pink (default) or White.
4
Click Signal On to generate the noise signal on the selected input. Click
Signal On again to terminate the noise signal.
Figure 5.2. Signal Generator window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
66
Operation ~ Utilities
To use tone
1.
Select the PSR1212 Unit and Input Channel the signal will be generated
on.
2.
Select Tone.
3.
Using the Frequency slider, select a specific tone frequency. You can also
enter the frequency in the box directly below the Frequency slider.
– or –
Use the Auto Sweep button to sweep a range of frequencies. Select the
Begin Frequency, the End Frequency, the Increment, and the Rate.
Auto Sweep provides the ability to move the frequency of the tone generator
from a low frequency to a high frequency at a specified rate. Click Auto
Sweep to begin the frequency sweep. The Frequency slide control and readout
reflect the progress of the Auto Sweep. Auto Sweep stops at the last frequency
in the sweep range upon completion of the sweep. Or you can click the button
at any time to stop the sweep. Sweep range is 20Hz—
20kHz; increment range
is 10Hz—
20kHz, and the rate range is 10ms—
2000ms. Default is 100ms.
Select Repeat if you want Auto Sweep to continue in cycles.
4.
Click Signal On to generate the tone. Click Signal On again to terminate
the noise signal.
Document Compare Utility
The Document Compare Utility samples and compares configuration information
Figure 5.3. Compare Utility button
between two sites. These can exist as actual sites/units or as documents (site files)
that are saved to your computer. It shows you where differences are between the two
and allows you to copy and paste settings between them. Open the Compare Utility
by clicking on the Compare Utility toolbar button.
To compare site files
Figure 5.4. You can also open the Document
Compare Utility from the Start menu
1.
Click the Browse button at the right of the Site 1 Document Name. This
opens the Open window.
2.
Select the first site file you want to compare. To compare the settings in a
connected site, click on the G-Ware Connections tab and select the unit or site.
3.
When you have made a selection, click Refresh to update the status of the
unit, site, or connection. Then click Open.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
Figure 5.5. Open window
4.
Repeat steps 1–3 to select the second second unit, site, or file for
comparison.
When you click Open, G-Ware automatically compares information from the
selected items and displays a table of parameters which differ (note that the
actual differences are not displayed at this point). This process can take a
minute or two.
Figure 5.6. Document Compare Utility showing two PSR1212 sites. The items
listed in the Site 1 and Site 2 columns show where the differences are found.
5.
To view the difference(s) between two sources on a single parameter, select
the row in the table you want to examine, then click Preview. This opens
the Print Preview window, which shows what the differences are.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
67
68
Operation ~ Utilities
Figure 5.7. Print Preview window
6.
To print the report, click Print (you can also click Print in the Compare
Utility window to print the report). The other buttons in this window allow
you to tailor the view of the report and browse sequentially through each
page.
7.
When you finish viewing or printing the report, close the Print Preview
window to return to the Document Compare Utility.
Copying settings
When two sites are compared, the Copy to Site, Paste, and Copy buttons at the
bottom of the window become selectable.
Print the comparison for
a detailed list of
differences between the
two sites.
-
Figure 5.8. Document Compare window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
In the window shown in Figure 5.8, clicking the Site 1 button transfers the
selected settings from a line selected in the Site 2 column to the corresponding
line in the Site 1 column. The Copy button copies the settings of the Site/Line
above it, allowing you to paste (with the Paste button) settings to another site,
unit, or even to a particular G-Ware parameter, such as an input.
The remaining buttons in the Document Compare window do the following:
•
Refresh button updates the connection status to site(s) or unit(s).
•
Select All selects everything in the Site 1/Site 2 table.
•
Select None deselects anything highlighted in the table.
•
Click Close to exit the Document Compare Utility.
Print Reports
The Print Reports utility allows you to print a variety of configuration reports. To
open the Print Reports utility, select Print from the File menu.
Figure 5.9. Print Reports window
Select the item(s) you want to print, then click Print Preview to view a
preview of the report or Print to print the report(s). For example, you could select
Inputs 1–8 Report to print a copy of the settings you’ve established for Inputs
1–8.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
69
70
Operation ~ Utilities
Make a note of the baud
rate selected in the Site
Properties
window
before opening the G-Ware
Firmware Utility.
-
GFirm Firmware Utility
To make it easy to upgrade your unit when new firmware enhancements are released,
G-Ware features a built-in firmware upgrade utility. Before upgrading firmware,
save a copy of your site files and verify that the flow control setting on the unit
(RS-232 menu on front panel LCD) is enabled. Also, make sure flow control is
set to Hardware in the G-Ware (Site Properties).
To upgrade firmware
Figure 5.10. GFirm button
1.
Connect the unit to the PC using a straight-through 9-pin serial cable.
2.
Open the G-Ware Firmware Utility by clicking on the GFirm toolbar button.
If the GFirm toolbar
button is not on the
G-Ware toolbar, you need
to install the current G-Ware
release. You can download GWare from the ClearOne web site
at www.clearone.com.
-
Figure 5.11. G-Ware Firmware Utility
3.
Click Browse to access a list of available firmware updates. Select the file
that matches the type of unit you are upgrading and click Open.
Figure 5.12. Available firmware files
4.
The selected firmware file will self verify and display the message Verified,
OK. If the file information matches your unit and the file is verified, click
Next to advance to the Communications tab.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
71
Operation ~ Utilities
5.
Select the PC COM port you are using for the upgrade. Select the Baud
Rate that matches the baud rate in the Site Properties window.
Figure 5.13. Selecting baud rate
6.
Click Next. If the upgrade requires you to save your site files, a warning
message will display. You will need to exit the G-Ware Firmware Utility,
sync to the units with G-Ware, and save the site file(s) if you have not done
so already. Click Yes, Continue to begin firmware upload.
7.
The Progress tab displays the status of the firmware upgrade. Do not
interrupt the procedure. The process begins by erasing flash sectors and
then uploading the firmware file.
8.
If the process fails, do not use the Start Over button. Close GFirm instead
and verify you are using a 9-pin straight-through serial cable and that baud
rate and flow control are configured properly. Restart GFirm and return to
step one of this procedure.
9.
When the upgrade is complete, the Finished tab appears. Check the front
panel of unit and verify the proper firmware version for your unit is now
displayed. If you have no more units to upgrade, you can now close the
GFirm program.
If updating multiple units, move the RS-232 connection to the next unit and
click Start Over to continue.
10. After upgrading the firmware on all units, restore expansion bus
connections.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
72
Operation ~ Utilities
G-Ware Switcher
G-Ware Switcher allows you to alternate between different G-Ware software versions
that are installed on the same PC.
For example, if you need to upgrade the firmware on your ClearOne unit(s),
G-Ware Switcher allows you to easily switch to an earlier version of G-Ware (such
as 3.5), save the site files, and then switch to a later version (4.5) to upgrade the
firmware.
Prior to the 4.5 release, the older version of G-Ware had to be removed
before the new version could be installed.
Before using G-Ware Switcher
1.
Load G-Ware 3.5 in a unique directory (path), as shown in Figure 5.14. Do
not select “Add Icon to Desktop”when you are asked if you want to do so
during the installation process.
2.
Load G-Ware 4.5 in a unique directory (path), as shown in Figure 5.15. Do
not select “Add Icon to Desktop”when you are asked if you want to do so
during the installation process.
You are now ready to use G-Ware Switcher.
Figure 5.14. Creating a
directory for G-Ware 3.5
To use G-Ware Switcher
1.
Launch G-Ware Switcher from the Windows Start menu by selecting
Programs, ClearOne G-Ware, and then G-Ware Switcher.
The G-Ware Switcher Utility Window opens. G-Ware Switcher
automatically searches the PC for G-Ware software versions and displays
them in the window.
Figure 5.15. Creating a
directory for G-Ware 4.5
Figure 5.16. G-Ware Switcher
2.
Select the G-Ware version you want to use.
3.
If the selected G-Ware version is active (if Yes appears in the Active column
for the version you want to run), click Run to launch it.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
73
Operation ~ Monitoring Views
If the selected G-Ware version is not active, click Re-Register/Make
Shortcuts to re-register the version so it becomes active. Then click Run to
launch it.
If you have installed a version of G-Ware that isn’t displayed in the G-Ware
Switcher window, click Refresh. G-Ware Switcher will locate and display the
version.
Copy and paste settings
In most areas of G-Ware software, right-clicking the mouse opens a shortcut menu.
The options on this menu change depending on which window you are in.
The version shown at left allows you to copy and paste unit settings and sites,
as well as add or remove units from a site. For example, to copy unit settings to
Figure 5.17. Shortcut menu
another unit, place the cursor in the blue area of the Flow Screen, then right-click
to open the shortcut menu. Select Copy Unit. Next, open (or add) another unit,
then right-click in the Flow Screen of the second unit to open the shortcut menu.
lick Paste Unit. This copies the properties of the first unit to the second one.
Message Log
The Message Log automatically displays messages indicating successful or
unsuccessful site connection and all errors. To open the Message Log, click the
Message Log toolbar button or select Message Log from the Tools menu.
Figure 5.18.
Message Log button
Figure 5.19. Message Log window
Monitoring Views
Gate View
The Gating button opens the Gate View window, which allows you to view gating
activity at each mic input on each unit in your site. Select Enabled to observe unit
gating information. Note that the window shows gating activity only for units
which have been added to G-Ware. The gate indicator for each input is dark green
in the gate-off condition and light green if the input is gated on. Click Close to
save the settings and exit.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Figure 5.20.
Gating button
74
Figure 5.21. Gate View window
Meter Views
The Meter Views window allows you to monitor the level of any input, output, or
processing signal of the PSR1212. You can monitor the same parameter on multiple
Figure 5.22.
Meters button
inputs (or outputs or processing channels) for comparison or you can monitor an
entire signal flow from input to output. Click the Meters button on the G-Ware
toolbar to open this window.
Figure 5.23. Meter Views window
To configure Meter Views
1.
Select the unit number, meter type, and channel you want to use. Note
that you can configure the meters such that you can monitor the same input
signal as it makes its way through various stages in the PSR1212.
2.
Enable the meter by clicking the adjacent Enabled box.
3.
When you have finished making changes, click Close to exit the window.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 6: Control
There are many ways to control your PSR1212 and other networked units. This
chapter explains how to set up control for Control/Status A port using GPIO Builder,
XAP IR Remote and ClearOne Control Panel using Remote Builder, and RS-232 port.
GPIO Builder
Control/Status A
GPIO stands for general-purpose input/output. The GPIO Builder is used to establish
the pin assignments for the 16 user definable pins on Control/Status Port A. These
pins provide control via contact closure and status via open collector functions in the
unit. Note that the pins numbered in blue are command pins; the pins numbered in
green are status pins. The default pin assignments are listed on page 85. You can
open GPIO Builder from the Flow Screen or the G-Ware toolbar.
To program control/status pins
1.
Select the Control/Status A pin you want to configure.
The current (default) pin assignment is displayed in the Active
(Low)/Inactive (High) Command box.
If you want to create pin
assignments specific to a
preset, you will need to
open the GPIO Builder from the
Preset Configuration pane (see
page 55) and select Use in Preset.
-
Figure 6.1. GPIO Builder Window
2.
Select the Device Type and ID from their respective lists.
3.
Select the Command from the Command list. When you select a command,
a description of it appears in the Command Description box.
4.
Select the command parameters from the argument lists. The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
5.
Click Apply to apply the changes you have made to the selected pin. Or,
click Clear to clear any programming for the pin.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
GPIO commands can be
configured only for the
local PSR1212 unit.
76
Control ~ Remote Builder
Remote Builder
The Remote Builder window is used to configure the optional XAP IR Remote
Control and ClearOne Volume and Select Control Panels. These control devices are
connected to Remote Panel A or Remote Panel B—
the RS-485 connectors. If you
want to create custom control assignments for presets, open the Remote Builder
from the Preset Configuration pane and select the Use in Preset option.
XAP IR Remote
The XAP IR Remote provides remote control of volume and mute for a PSR system.
You can connect up to two XAP IR Remote Controls—
one to each RS-485 port. See
the XAP IR Remote user manual for more information. The XAP IR Remote has five
Figure 6.2. Remote Builder
button on Flow Screen
programmable buttons and one programmable LED. You can customize your XAP
IR Remote using the Remote Builder. To open the Remote Builder, click the
Remote Builder button on the Flow Screen (or the button in the G-Ware
toolbar).
Figure 6.3. Remote
Builder toolbar button
If you want to program
different button assignments for use in a preset,
you will need to open the Remote
Builder
from
the
Preset
Configuration pane (see page 55)
and select Use in Preset.
-
Figure 6.4. Remote Builder
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
77
Control ~ Remote Builder
To program the XAP IR Remote
1.
Select an ID number for the remote from the Select Remote ID list.
2.
Click Change Name to create a more descriptive name for the remote
which is displayed in addition to the remote number (limit 20 characters).
3.
Select IR Remote (default) from the Select Remote Type list.
4.
In the Telephone Interface section, select the Device Type and ID of the unit
(XAP 400 or XAP TH2) that you want the XAP IR remote to use when
making and receiving calls. The default settings are ** which will select any
telco device found on the network. If you have multiple telco devices in your
network, you must specify which unit will be used to make and receive calls.
5.
Select the button or LED you want to program from the Select Button/LED
list. You can also select the button or LED by clicking directly on the picture
of the remote. (Selectable buttons are colored white.)
6.
Click the Active Command or Inactive Command button to set the
command for operation when the button is active or inactive.
7.
Select the Device Type, ID, and Command from their respective lists.
When you select a command, a description of it appears in the Command
Description box.
8.
Select the command parameters from the argument lists. The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
9.
Click the Apply button to apply the command to the selected Active or
Inactive command button. Or, click Clear to clear any programming.
ClearOne Control Panels
ClearOne Control Panels are convenient wall panels which provide control over the
PSR1212 audio conferencing system. There are two Control Panel models: Volume
and Select. You can connect up to six Control Panels in daisy chain fashion to each
RS-485 port. See Appendix C for more information. The Control Panel buttons are
programmed using the Remote Builder. You can open the Remote Builder using the
Remote Builder button on the Flow Screen or the Remote Builder button on the
G-Ware toolbar.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Up to five control panels
and one IR remote can
be connected to each of
the RS-485 ports. In addition to
selecting the ID number in the
software, you will also need to
use the DIP switches on the IR
receiver to assign the Device ID.
See the XAP IR Remote manual
for more information.
-
78
Each Control Panel
button
can
be
programmed to respond
like a momentary or latching
button. A command can be
programmed to activate or
deactivate a particular function.
-
Control ~ Remote Builder
To program the Volume panel
1.
Select an ID number for the remote from the Select Remote ID list.
2.
Click Change Name to create a more descriptive name (limit 20
characters) for the remote which is displayed in addition to the remote
number in the Select Remote ID list. The name is also updated on the
graphic label.
Up to six control panels
(or five control panels
and one IR remote) can
be connected to each of the RS485 ports. In addition to
selecting the ID number in the
software, you will also need to
use the DIP switches on the
control panel to assign the Device
ID. See Appendix C: Control
-
Figure 6.5. Volume Panel selected in the Remote Builder
3.
From the Remote Type list, select Volume. The Control Panel graphic will
change to match your selection.
4.
Select the button or LED you want to program from the Button/LED
Selection list. You can also select the button or LED by clicking directly on
the picture of the Volume panel.
If you want to program
different button assignments for use in a preset,
you will need to open the Remote
Builder
from
the
Preset
Configuration pane (see page 55)
and select Use in Preset.
The default numbers on the left of the Volume panel LEDs represent gain
-
levels in decibels. To change a level, click on the LED and then select the
level from the Gain list at the bottom of the window. You can also set the
upper and lower limits of gain on LEDs L2 and L8 and then click Auto
Scale, which automatically assigns values to LEDs L3-L7 on a distributed
scale.
5.
Click the Active Command or Inactive Command button to set the
command for operation when the button is active or inactive.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
79
Control ~ Remote Builder
6.
Select the Device Type, ID, and Command from their respective lists.
When you select a command, a description of it appears in the Command
Description box.
7.
Select the command parameters from the argument lists. The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
8.
Click the Apply button to apply the command to the selected Active or
Inactive command button. Or, click Clear to clear programming.
To program the Select panel
1.
Select an ID number for the remote from the Select Remote ID list.
2.
Click Change Name to create a more descriptive name (limit 20
characters) for the remote which is displayed in addition to the remote
number in the Select Remote ID list. The name is also updated on the
graphic label.
Figure 6.6. Select Panel selected in the Remote Builder
3.
From the Remote Type list, select Select. The Control Panel graphic will
change to match your selection.
4.
Select the button or LED you want to program from the Button/LED
Selection list. You can also select the button or LED by clicking directly on
the picture of the Select panel.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
If you want to program
different button assignments for use in a preset,
you will need to open the Remote
Builder
from
the
Preset
Configuration pane (see page 55)
and select Use in Preset.
-
80
Control ~ RS-232 Port
5.
Click the Active Command or Inactive Command button to set the
command for operation when the button is active or inactive.
6.
Select the Device Type, ID, and Command from their respective lists.
When you select a command, a description of it appears in the Command
Description box.
7.
Select the command settings from the argument lists. The options that are
available depend on the command selected. When you select an argument, a
description of it appears in the Argument Description box.
8.
Click the Apply button to apply the command to the selected Active or
Inactive command button. Or, click Clear to clear programming.
RS-232 Port
Remote Modem Access
You can access the unit remotely through a modem connected to the serial port. To
enable this feature, configure the port for modem mode.
When in modem mode, the serial port will send an initialization string to the
modem upon entering the mode or upon power-up of the unit. You program the
initialization string in Site Properties window in G-Ware. Typical configurations
you set with the initialization string include setting a fixed baud rate for the unit
and setting up auto-answer parameters.
The modem password is
created in the Unit
Properties window (see
page 26) or by using the MPASS
serial command (see page 114).
-
You must enter a password before you can control the system this way. The
default password is blank (a carriage return). You can change it to any
combination of letters and/or numbers up to 12 characters. It is not case-sensitive.
When you establish a valid serial connection with the unit in modem mode,
the unit will wait for a carriage return. When you have entered a carriage return,
the system will prompt you to enter the password. If there is no activity for five
minutes on the serial port while in modem mode, the unit will re-prompt for the
password.
Serial commands
Serial commands can be passed through the PSR1212 RS-232 port using Hyper
Terminal, touch panels, or other compatible remote control devices. To learn more
about serial commands, see Appendix E.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
81
Control ~ RS-232 Port
Command strings
By creating command strings, you can use your PSR1212 to control equipment such
as lighting, projectors, and room dividers as well as other ClearOne products. A
command string is passed to the connected device via the PSR1212’s RS-232 port.
You can create up to eight customized serial command strings (limit 80 characters
each) in the Command Strings window. To open the Command Strings window, click
the Command Strings toolbar button.
Figure 6.7. Command
Strings toolbar button
Figure 6.8. Command Strings window
To create a command string
Special characters
•
Type the serial command string (limit 80 characters) in one of the eight
\a = alert
locations. The command string will support special characters. See list at
\b = backspace
right.
\f = formfeed
\n = new line
To run a command string
\r = carriage return
•
Use any external control device (e.g. Control Panel, GPIO control) to run
\v = vertical tab
the STRING serial command.
\\ = backslash
– or –
•
Incorporate the STRING command into a macro which can be run from
G-Ware, the front panel, or any external control device.
For information on creating macros, see page 61. For information on GPIO builder,
see page 75. For information on Control Panels, see page 77.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
\t = horizontal tab
82
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
APPENDICES
Appendix A: Specifications
Dimensions (LxDxH)
Mic/Line Inputs 1-8
17.25" x 10.25" x 1.25"
43.8 x 26 x 4.5 cm
Push-on terminal block, balanced,
bridging
Impedance: 5kž
Nominal Level: adjustable -55dBu,
-25dBu, 0dBu
Maximum Level: -35dBu, -5dBu,
+20dBu
Phantom Power: 24V, selectable
Weight
7 lb/4.5 kg dry
12 lb/5.9 kg shipping
Operating Temperature
32–100° F/0–38° C
Humidity
High shelving
Parametric EQ
Notch
CD Horn
Crossovers:
Bessel
Butterworth
Linkwitz-Riley
Compressor
Delay adjustable up to 500ms
Line Inputs 9-12
Matrix Mixing Parameters
Auto-adjusting
100–240VAC; 50/60Hz
Push-on terminal block, balanced,
bridging
Impedance: >10kž
Nominal Level: 0dBu
Maximum Level: 20dBu
Power Consumption
Outputs 1-12
Auto Mixer Parameters
30W typical
Push-on terminal block, balanced
Impedance: 50ž
Nominal Level: 0dBu
Maximum Level: 20dBu
Number of Open microphones (NOM)
PA Adaptive Mode
First Mic Priority Mode
Last Mic Mode
Maximum # of Mics Mode
Ambient Level
Gate Threshold Adjust
Off Attenuation Adjust
Hold Time
Decay Rate
15% to 80%, non-condensing
Power Input Range
Expansion Bus In/Out
Proprietary Network
RJ-45 (2), 115.2kbps, 110kž impedance
Category five twisted-pair cable
80' (24 meters) maximum cable
length between any two PSR1212s,
XAP 800s or XAP 400s
RS-232
DB-9 female
9,600 /19,200/38,400 (default)/57,600
baud rate; 8 bits, 1 stop, no parity
Hardware flow control on (default)/off
Control/Status
DB-25 female A/B (2)
Inputs A/B: active low (pull to ground)
Outputs A/B: Open collector, 40VDC max,
40mA each
+5VDC pins (2) (300mA over-current
protected)
Audio Performance
Conditions: Unless otherwise specified all
measurements are performed with a
22Hz to 22kHz BW limit (no weighting).
Frequency Response: 20Hz to 20kHz
±1dB
Noise (EIN): -126dBu, 20kHz BW,
max gain, Rs=150ž
THD+N: <0.02%
SNR: 80dB re 0dBu, (A-weighted)
Dynamic Range: 100dB (A-weighted)
Crosstalk <-91dB re 20dBu @ 20kHz
channel to channel
Approvals
FCC, CSA, IC, CE, NOM, ACA, SABS,
JATE
Assignable Processing Blocks
Remote Panels A/B
4-pin push-on terminal block
RS-485 proprietary protocol
Cat five twisted-pair cable
1 pair data, 1 pair power and ground
+15VDC (300mA over-current protected)
Filters:
All pass
Low pass
High pass
Low shelving
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
32x32 matrix
12 analog in/out
12 expansion bus in/out
8 assignable processing blocks in/out
Microphone Input Configuration
Input Gain Adjust
Mic or Line Level
Phantom Power on/off
Filters
All Pass
Low Pass
High Pass
Notch
PEQ
Mute on/off
Chairman Override on/off
AGC on/off
Auto Gate/Manual Gate
Adaptive Ambient on/off
Set-up Software
84
Appendices ~ Appendix B: Pinouts
Appendix B: Pinouts
5
9
1
RS-232 COM DCE port pinout (female)
Figure B.1. RS-232 connector
!
ClearOne recommends
that all nine pins be
connected
to
avoid
DB-9
Male
PSR1212
Pin Number
Control
Pin Number
Control
1
DCD
6
DSR
2
TXD
7
CTS
3
RXD
8
RTS
4
DTR
9
No connection
5
Ground
6
DB-9
Male
DB-9
Female
DB-25
Female
Pin 1
Pin 1
Pin 2
Pin 2
TXD (Pin 2)
TXD (Pin 2)
Pin 3
Pin 3
RXD (Pin 3)
RXD (Pin 3)
Pin 5
Pin 7
DTR (Pin 4)
Pin 4
GND (Pin 5)
GND (Pin 5)
Pin 6
Pin 6
CTS (Pin 7)
CTS (Pin 7)
RTS (Pin 8)
RTS (Pin 8)
Pin 9
Pin 9
PC
PSR1212
Figure B.3. PSR1212 to Modem RS-232 Connections
Figure B.2. PSR1212 to PC RS-232 connections
DB-9
Female
Phoenix
Connectors
TXD (Pin 2)
RX2 (White)
RXD (Pin 3)
TX2 (Red)
GND (Pin 5)
GND (Black)
DB-25
Female
AMX
PSR1212
Modem
Modem
TXD (Pin 2)
TXD (Pin 2)
RXD (Pin 3)
RXD (Pin 3)
RTS (Pin 7)
GND (Pin 5)
CTS (Pin 4)
DTR (Pin 4)
GND (Pin 5)
CTS (Pin 7)
RTS (Pin 8)
CTS (Pin 7)
RTS2 (Green)
GND (Pin 6)
RTS (Pin 8)
CTS2 (Blue)
RTS (Pin 20)
Figure B.4. PSR1212 to AMX RS-232 Connections
DB-9
Male
AMX
Figure B.5. Modem to AMX RS-232 Connections
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
85
Appendices ~ Appendix B: Pinouts
Control/Status connectors
13
1
The Control/Status connections are provided on two DB-25 connectors. These
connectors are labeled Control/Status A and Control/Status B and contain different
25
14
types of pins. The inputs on these connectors are internally pulled high and are
activated by connecting the pin to ground. The outputs are open collectors, which
Figure B.6. Control/Status Ports A, B
are open when inactive and grounded when active. This allows the PSR1212 to
control and be controlled by a wide variety of external devices, including relays,
lamps, switches, and other equipment. Control pins on Control/Status A are
momentary while control pins on Control/Status B are latching.
Control/Status A Port Pinout (female)
Pin
Definable
Type
Default Description
1
Yes
Control
Lock front panel toggle
2
Yes
Status
Status of front panel lock
3
Yes
Control
Mute all mics toggle
4
Yes
Status
Status of mute all mics
5
Yes
C
Mute Output 9 toggle
6
Yes
S
Status of Output 9 mute
7
Yes
C
Mute Output 10 toggle
8
Yes
S
Status of Output 10 mute
9
Yes
C
Mute Output 11 toggle
10
Yes
S
Status of Output 11 mute
11
Yes
C
Mute Output 12 toggle
12
Yes
S
Status of Output 12 mute
13
Yes
C
Volume Up D Output 1 (1dB)
14
Yes
S
Not programmed
15
Yes
C
Volume Down D Output 1 (1dB)
16
Yes
S
Not programmed
17
No
S
Mic #1 Gate Status
18
No
S
Mic #2 Gate Status
19
No
S
Mic #3 Gate Status
20
No
S
Mic #4 Gate Status
21
No
S
Mic #5 Gate Status
22
No
S
Mic #6 Gate Status
23
No
S
Mic #7 Gate Status
24
No
S
Mic #8 Gate Status
25
No
Ground
Ground
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
The first 16 pins on the
Control/Status Port A
can be programmed
u
s
i
n
g
G-Ware software.
-
86
Appendices ~ Appendix B: Pinouts
Control/Status B port pinout
Pin
Definable*
Type
Default Description
1
No
C
Preset select bit
2
No
S
Preset select status for Pin 1
3
No
C
Preset select bit
4
No
S
Preset select status for Pin 3
5
No
C
Preset select bit
6
No
S
Preset select status for Pin 5
7
No
C
Preset select bit
8
No
S
Preset select status for Pin 7
9
No
C
Preset select bit
10
No
S
Preset select status for Pin 9
11
No
C
Preset select bit
12
No
S
Preset select status for Pin 11
13
No
C
Preset select bit
14
N
S
Preset select status for Pin 13
15
No
C
Preset select bit
16
No
S
Preset select status for Pin 15
17
No
C
Preset select bit
18
No
S
Preset select status for Pin 17
19
No
C
Preset select bit
20
No
S
Preset select status for Pin 19
21
No connection
22
No connection
23
No
-
+5VDC, 300mA
24
No
-
+5VDC, 300mA
25
No
-
Ground
Control/Status A and B: DB-25 female
Inputs A and B: active low (pull to ground)
Outputs A and B: Open collector, 40V max, 40mA each
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
87
Appendices ~ Appendix B: Pinouts
RS-485 Remote Panel A and B connectors
Pin
Description
1
+15VDC, 300mA (over-current protected)
2
Data +
3
Data –
4
Ground
4
3
2
1
4
3
2
Figure B.7. RS-485 Remote Control Ports
Set connector pinout
Pin
Description
Pin
Description
1
To pin 6 of SET RJ-11C
4
Tip
2
To pin 5 of SET
5
To pin 2 of LINE
3
Ring
6
To pin 1 of LINE RJ-11C
Line connector pinout
Pin
Description
Pin
Description
1
To pin 6 of LINE RJ-11C
4
Ring
2
To pin 5 of LINE
5
To pin 2 of SET
3
Tip
6
To pin 1 of SET RJ-11C
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
1
88
Appendices ~ Appendix C: Control Panel
Appendix C: Control Panel
This equipment must be
installed according to
applicable
local
electrical codes.
!
The Volume Control Panel and Select Control Panel connect to either the Remote
Panel A or B connector of the PSR1212, XAP 800, or XAP 400 and works by
triggering the execution of programmed commands from the XAP/PSR unit. Each
button on the control panel is programmable to execute a single command or a
series of commands. Button function is programmed using G-Ware software (see
the XAP or PSR user manual). Each Control Panel fits inside a standard electrical
wall box and must be installed according to local electrical codes.
ON
1
Connecting the Control Panel
2
3
4
5
6
7
8
1.
Ensure you received a facia plate; a Control Panel assembly with mounting
bracket and two RS-485 Phoenix four-pin connectors; two connector
Figure C.1. DIP switches
terminator blocks; a faceplate; two flat HD screws; two pan-head screws;
and an electrical wall box (shown in Figures C.5 and C.6). If any parts are
missing, please contact ClearOne.
2.
Using DIP switches 1–4, assign a unique ID to the Control Panel. Refer to
Figure C.2 for proper DIP switch settings. If you set an invalid address, all LEDs
on the Control Panel will illuminate.
3.
Set DIP switch 8 to the on position if you are using just one Control Panel. If you
have more than one Control Panel daisy-chained to the same Remote Panel
connector, set only the last Control Panel’s DIP switch 8 to on. Switches 5-7 are
nonfunctional.
4.
Turn off the XAP/PSR unit (unplug the unit).
5.
Wire each end of a Cat. 5 cable to a connector terminator block. Use one
Figure C.2. DIP switch settings
twisted wire pair for the center - and + connections (pins 2 and 3) and the
other twisted pair for the ground and +15V connections (pins 1 and 4).
Failure to correctly wire the connector can result in damage to the unit.
Figure C.3. Wiring the Control Panels
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
89
Appendices ~ Appendix C: Control Panel
6.
Connect one connector terminator block to the Remote Panel on the
Control Panel Assembly
Dimensions
(both
versions): 1.8"/4.6cm W
x 4.125" /10.5cm L (not including
faceplate or electrical box).
-
XAP/PSR unit. Route the other end of the cable through the back of the
electrical wall box and connect the terminator block to the Control Panel.
7.
To use a second Control Panel, connect it to the unused Remote Panel
connector on the XAP/PSR unit or the unused connector on the first Control
Panel. You can daisy-chain up to six Control Panels to each Remote Panel
connector. Total cable run depends on the number of Control Panels used.
The distance information in the table at left is based on Cat. 5 cable with a
nominal resistance of 27ž per 1,000 feet (305 meters). All distances refer to
total cable runs from a single Remote Panel connector. For information
about extending beyond 800 feet (244 meters) total with six Control Panels,
call Technical Support at 1-800-283-5936.
8.
As shown in Figures C.5 and C.6, use the supplied pan-head screws to install
# of Control Panels
1
Maximum Distance
3,000 ft/914 meters
2
3
4
2,500 ft/762 meters
1,600 ft/488 meters
1,200 ft/366 meters
5
6
1,000 ft/305 meters
800 ft/244 meters
Figure C.4. Control panel distance chart
the Control Panel PCB assembly to the electrical wall box.
9.
To install the facia plate, position it over the conductive rubber switch pads
on the PCB assembly, as shown in Figures C.5 and C.6.
10. Mount the faceplate over the rubber switch pads, using the two flat HD
screws.
460-155-002 WALL ENCLOSURE 2.25 X 3.25 INCHES
681-010-616 SCREWS (2) 6-32 X 1 INCH PPH
740-155-050 FACIA PLATE
460-155-001 FACEPLATE
FLAT HEAD SCREWS (2)
INCLUDED WITH FACEPLATE
673-016-104
CONN TERM BLOCK/
F EURO 4 P
(2 EACH)
915-155-050
820-155-050
740-155-052
625-100-006
ASSEMBLY, SELECT CONTROL PANEL INCLUDES:
CONTROL PANEL PCB ASSEMBLY W/TWO FOUR-PIN PHOENIX CONNECTORS
CONTROL PANEL MOUNTING BRACKET
ELASTOMER CONDUCTIVE RUBBER SWITCH PADS (4 EACH)
SELECT CONTROL PANEL 910-155-050
Figure C.5. Select Control Panel Assembly
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
90
Appendices ~ Appendix C: Control Panel
460-155-002 WALL ENCLOSURE 2.25 X 3.25
915-155-051
820-155-051
740-155-052
625-100-006
ASSEMBLY, VOLUME CONTROL PANEL INCLUDES:
VOLUME CONTROL PANEL PCB ASSEMBLY W/TWO FOUR-PIN PHOENIX CONNECTORS
CONTROL PANEL MOUNTING BRACKET
ELASTOMER CONDUCTIVE RUBBER SWITCH PADS (3 EACH)
740-155-051 FACIA PLATE
460-155-001 FACEPLATE
FLAT HEAD SCREWS (2)
INCLUDED WITH FACEPLATE
681-010-616 SCREWS
(2) 6-32 X 1 INCH PPH
673-016-104
CONN TERM BLOCK/
F EURO 4 P
(2 EACH)
VOLUME
CONTROL PANEL 910-155-051
Figure C.6. Volume Control Panel Assembly
This equipment complies with the requirements of the European guidelines:
89/336/EEC “Electromagnetic Compatibility”and 93/68/EEC “Electrical
operating material for use within specific voltage limits.”
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix D: Accessories
Appendix D: Accessories
Accessory
ClearOne Part Number
Tabletop Omni Microphone
910-103-160 (with cable)
Tabletop Uni Microphone
910-103-161 (with cable)
Button Omni Microphone
910-103-162 (black button)/910-103-163 (white button)
Button Uni Microphone
910-103-164 (black button)/910-103-165 (white button)
Delta Microphone
910-103-340
Acc. Kit, Side Trim
860-150-002
Wall Mount Speaker
910-103-010
Select Control Panel
910-155-050
Volume Control Panel
910-155-051
XAP IR Remote
910-170-150
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
91
92
Appendices ~ Appendix E: Serial Commands
Appendix E: Serial Commands
The PSR1212 accepts serial commands through the serial port or the expansion bus. The commands in this manual
pertain only to the PSR1212. RS-232 serial port protocol is 9,600, 19,200, 38,400 (default), or 57,600 baud; 8
bits, 1 stop bit, no parity.
Conventions
The following typographic conventions are used in this document to describe the different serial commands. Use the
Command structure section and the examples as a guide when creating your serial commands.
Convention
Description
<X>
Parameters enclosed in < > indicate a mandatory parameter.
[X]
Parameters enclosed in [ ] indicate an optional parameter.
1-8
Parameters separated by a - indicate a range between the values.
4,7,9
Parameters separated by a , indicate a list of available values.
EREF
Words in uppercase bold indicate command text.
DEVICE
Indicates the device type and device number on the expansion bus network. It is composed of a
device type character and a device number. The device type for the PSR1212 is always 4 and the
device ID will always be 0–7, or * (to select all PSR units).
Command structure
Commands can be either UPPER CASE or lower case. Also, extra spaces or tabs between arguments in text
commands are allowed. Return values are always in upper case. In order for a command to be recognized by the serial
port, the command must be terminated by a carriage return.
The structure of serial commands is as follows: #DEVICE COMMAND [X] [X]
#
indicates the start of a command line
DEVICE
represents the device type and device number
COMMAND
is the command text
[X] [X]
represents any additional options in the order that they appear in the command descriptions that
follow
Example
A command to disable automatic gain control for Mic 2 on a PSR1212 device “0”will have the command line:
#40 AGC 2 M 0. In this command line, 4=PSR1212, 0=unit 0, AGC=command, 2=channel, M=Mic Input group,
0=off state. If a command calls for a “null”value, leave a blank in the command line. For example, “#40 AGC 2 M”
will return the current AGC state of Mic 2 on device 50.
Command responses will have a carriage return line feed. Example: #40 AGC 2 M O carriage return line feed.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
Groups and channels
If a channel has an alpha value of “*”, the command is to be applied to all channels. For example, a group value
of M and a channel value of * would mean that the command is to be applied to all channels of group M (mic
inputs). The following table show the alpha representations for the different groups and the channels that are
available for each product.
Type and device IDs
Type ID
Unit type
Device ID range
4
PSR1212
0–7
5
XAP 800
0–7
6
XAP TH2
0–F
7
XAP 400
0–7
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
93
94
Appendices ~ Appendix E: Serial
Meter type definitions
Serial command error codes
Error number
Text message
Explanation/Solution
1
Memory error
The box is out of internal memory. Power cycle the box.
2
No command found
A command was not found in the string.
3
Unknown command
response
A command was executed on a different device type that this box
cannot display. The command dictionary needs to be updated.
4
Not implemented
The command is not implemented.
5
Argument error
The command had an argument that was out of range.
6
Unknown command
The command is unknown to this unit.
7
Bad checksum
The binary command’s checksum is wrong.
8
Preset of macro invalid
A preset or macro failed to program because it is too large or
because its command list contained an invalid command.
10
Queue error
The internal command queue is full. Enable flow control and use
all five pins on the serial port.
11
Command too big
The binary command is too large.
12
Unit is locked
Unlock the unit with the proper password.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
95
Appendices ~ Appendix E: Serial Commands
PSR1212 Serial commands
Command
Function
Command
Function
AAMB
Selects/reports adapt ambient setting
LOCK
Selects/reports the state of the preset and
AGC
Enable/disables AGC
AMBLVL
Selects/reports ambient level
BAUD
Selects/reports the baud rate of the serial port
being
CGROUP
Selects/reports compressor group setting
LOCKPRST
CHAIRO
Selects/reports chairman override setting
preset or macro. If a preset or macro has the
COMPRESS
Sets/reports compressor on audio processing
lock applied, it can be changed only if the unit
channel
is unlocked with the password.
COMPSEL
Selects/reports compressor activity for
macro lock. When on, the lock prevents presets
and macros that have been flagged from
LOCKPWD
altered in any way.
Selects/reports whether the lock is applied to a
Selects/reports the password for the
processor
preset/macro lock. This can be changed only if
DECAY
Sets/reports decay rate
the unit is unlocked.
DELAY
Sets/reports delay rate
LVL
Reports in, out, or processor level
DELAYSEL
Selects/reports processor channel delay
LVLREPORT
Selects/reports level status
DFLTM
Sets/reports default meter
LVLRRATE
Sets the level report rate for the unit
DID
Selects/reports device ID
MACRO
Executes macro or reports last macro
FILTER
Selects/reports input/processor channel filter
FILTSEL
executed
setting
MASTER
Reports the mode of the unit
Enables/disables filters on input/processor
MAX
Changes/reports max gain setting for in, out,
channel
FLOW
FMP
processor block
Selects/reports the flow control of the serial
MDMODE
Enables/disables the modem mode for the unit
port
MIN
Changes/reports minimum gain setting for in,
Sets/reports 1st Mic Priority for mic gating
group
out, processor block
MINIT
Sets/reports modem initialization string of
FPP
Sets/reports current passcode setting
serial port
GAIN
Changes/reports gain for in, out, or process.
GATE
Reports gate status of channels 1–8
GHOLD
Selects/reports hold time setting
GMODE
Selects/reports gating mode setting
GOVER
Selects/reports gating override setting
GRATIO
Selects/reports gate ratio setting
GREPORT
Selects/reports gate status report frequency
GRPSEL
Selects/reports input gating group assignments
LABEL
Selects/reports label of specified channel
MTRX
Selects/reports matrix routing of an in. to out.
LFP
Sets/reports status of front panel access
MTRXLVL
Selects/reports matrix level at the cross point
LMO
Selects/reports Last Mic On mode
MUTE
Sets/reports mute status
MINMAX
Changes/reports min and max gain from in,
out, processor block
MLINE
Selects/reports coarse gain adjustments on
Inputs 1–8
MMAX
Selects/reports max # of mics for each mic
MPASS
Sets passcode setting when using modem
group
mode
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
96
Appendices ~ Appendix E: Serial Commands
Command
Function
Command
Function
NOM
Selects/reports NOM setting on output
SERECHO
Selects/reports the serial echo of the RS-232
channels
SERMODE
Selects/reports the serial mode of the RS-232
Selects/reports off attenuation mode for
SFTYMUTE
Selects/reports the state of the safety mute.
OFFA
PAA
Inputs 1–8
When on, the safety mute holds all outputs in a
Selects PA adapt mode for specified input
muted state.
PP
Selects/reports phantom power setting
SIGGEN
Selects/reports signal generator activation
PRESET
Executes preset or reports last executed preset
SIGTOUT
Sets the signal generator time out for the unit
PRGSTRING
Sets/reports a programmed string
STRING
Executes a string for the RS-232 port
RAMP
Start/stops the gain ramp for an input, output,
TOUT
Selects/reports the title screen inactivity time
or assignable processing block
out
REFSEL
Selects/reports PA adapt mode for mic outputs
UID
Reports unit ID (read only)
REFSET
Selects/reports the output the reference channel
VER
Reports unit version (read only)
tracks
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
AAMB - Adaptive Ambient Mode
This command selects/reports the setting of adaptive ambient.
Command form: DEVICE AAMB <Channel> <Group> [Value]
Argument details
Name
Device
AAMB
Channel
Group
Value
Description
0–7 or * to select all units
Command form
Range 1–8 (Selects input)
M (Selects mic group)
0 = Off, 1 = On, 2 = Toggle, Null to query in text
Example: #41 AAMB 2 1 On PSR1212 unit 1 (#41), adaptive ambient (AAMB)
for mic channel 2 (2) is set on (1).
AGC - Automatic Gain Control
This command selects/reports the setting of automatic gain control.
Command form: DEVICE AGC <Channel> <Group> [Value]
Argument details
Name
Device
AGC
Channel
Group
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels on page 93
1,3,7 (I,M,L)
0 = Off, 1 = On, 2 = Toggle, Null to query in text
Example: #44 AGC 1 M 0 On PSR1212 unit 4 (#44), the automatic gain
control (AGC) on mic (M) channel 1 is set to off (0).
AMBLVL - Ambient Level Adjust
This command selects/reports the setting of the ambient level.
Command form: DEVICE AMBLVL <Channel> [Value]
Argument details
Name
Device
AMBLVL
Channel
Value
Description
0–7 or * to select all units
Command form
Range 1–8 (selects input channel)
-80.0 to 0 (sets ambient level in dB), Null to return current level
Example: #43 AMBLVL 1 -30 On PSR1212 unit 3 (#43), the ambient level
(AMBLVL) for mic input 1 is set to -30dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
97
98
Appendices ~ Appendix E: Serial Commands
BAUD - Baud Rate
This command selects/reports the baud rate of the serial port.
Command form: DEVICE BAUD [Value]
Argument details
Name
Device
BAUD
Value
Description
0–7 or * to select all units
Command form
9600, 19200, 38400, 57600
(Null to query in text)
Example: #46 BAUD 38400 On PSR1212 unit 6 (#46), the baud rate (BAUD)
for the RS-232 port is set to 38,400 (38400).
CGROUP - Compressor Group Select
This command selects/reports the setting of the compressor group on each assignable
processing channel.
Command form: DEVICE CGROUP <Channel> [Value]
Argument details
Name
Device
CGROUP
Channel
Value
Description
0–7 or * to select all units
Command form
range A–H (selects processing channel)
0 = none, 1 = compressor group 1, 2 = compressor group 2,
3 = compressor group 3, 4 = compressor group 4,
null to return the current mode
Example: #42 CGROUP A 2 On PSR1212 unit 2 (#42), the compression group
(CGROUP) for processing channel A is 2.
CHAIRO - Chairman Override Mode
This command selects/reports the setting of chairman override.
Command form:
DEVICE CHAIRO <Channel> [Value]
Argument details
Name
Device
CHAIRO
Channel
Value
Description
0–7 or * to select all units
Command form
Range 1–4 (selects mic input)
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Example: #47 CHAIRO 3 1 On PSR1212 unit 7 (#47), chairman override
(CHAIRO) for mic channel 3 is set on (1).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
99
Appendices ~ Appendix E: Serial Commands
COMPRESS - Compressor Adjust
This command selects/reports the setting of the compressor on processing channels.
Command form
DEVICE COMPRESS <Channel> [Threshold] [Ratio] [Attack]
[Release] [Gain]
Argument details
Name
Device
COMPRESS
Channel
Threshold
Ratio
Attack
Release
Gain
Description
0–7 or * to select all units
Command form
Range A–H (selects processing channel)
-30 to 20, Null to return current value
1 to 20
0.00 to 100.00 (select in .5ms intervals)
100 to 2000 (select in 5ms intervals)
0.00 to 20.00
Units
dB
ms
ms
dB
Example: #41 COMPRESS A 6 5 25 250 3 On PSR1212 unit 1 (#41), the
compression (COMPRESS) within processing channel A is set to have a threshold of
6dB, a ratio of 5:1 (5), an attack time of 25ms, a release time of 250ms, and a
gain of 3dB.
COMPSEL - Compression Select
This command selects/reports the compressor activation of each assignable
processing channel.
Command form:
DEVICE COMPSEL <Channel> [Value]
Argument details
Name
Device
COMPSEL
Channel
Value
Description
0–7 or * to select all units
Command form
Range A–H (selects processing channel)
0 = Off, 1 = On, 2 = Toggle, Null returns current state
Example: #40 COMPSEL A 1 On PSR1212 unit 0 (#40), the compression
(COMPSEL) within processing channel A is set on (1).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
100
Appendices ~ Appendix E: Serial Commands
DECAY - Decay Adjust
This command selects/reports the setting of the decay rate for a specified input.
Command form:
DEVICE DECAY <Channel> [Value]
Argument details
Name
Device
DECAY
Channel
Value
Description
0–7 or * to select all units
Command form
Range 1–8 (selects mic input)
1 = Slow, 2 = Medium, 3 = Fast, Null to return current state
Example: #43 DECAY 1 3 On PSR1212 unit 3 (#43), the decay rate (DECAY)
for mic channel 1 is set to fast (3).
DELAY - Delay Adjust
This command selects/reports the delay time of each assignable processing channel.
Command form: DEVICE DELAY <Channel> [Value]
Argument details
Name
Device
DELAY
Channel
Value
Description
0–7 or * to select all units
Command form
A–H (select processing channel)
0.00 to 500 (selects delay)
Null to return current state
Units
ms
Example: #46 DELAY A 200 On PSR1212 unit 6 (#46) the delay (DELAY) for
processing channel A is set to 200ms.
DELAYSEL - Delay Select
This command selects/reports the delay activation of an assignable processing
channel.
Command form: DEVICE DELAYSEL <Channel> [Value]
Argument details
Name
Device
DELAYSEL
Channel
Value
Description
0–7 or * to select all units
Command form
A–H (select processing channel)
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Example: #44 DELAYSEL A 1 On PSR1212 unit 4 (#44) the delay
(DELAYSEL) within processing channel A is enabled (1).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
DFLTM - Default Meter
This command selects/reports the setting of the default meter.
Command form: DEVICE DFLTM [Channel] [Group] [Position]
Argument details
Name
Device
DFLTM
Channel
Group
Position
Description
0–7 or * to select all units
Command form
1–12
I = Inputs, O = Outputs, M = Mic Inputs, L= Line Inputs
I, A, N, G, as applicable for group
(see Meter Type definitions, page 94)
Example: #45 DFLTM 8 O A On PSR1212 unit 5 (#45), the default meter
(DFLTM) is set to output (O) 8 after the gain adjustment (A).
DID - Device ID
This command selects/reports the device ID.
Command form:
DEVICE DID [Value]
Argument details
Name
Device
DID
Value
Description
0–7 or * to select all units
Command form
0–7 (select device ID)
Example: #47 DID 0 On PSR1212 unit 7 (#47), the device ID (DID) is set to 0.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
101
102
Appendices ~ Appendix E: Serial Commands
FILTER - Filter Adjust
This command selects/reports the setting of filters.
Command form:
DEVICE FILTER <Channel> <Group> <Node> [Type]
[Frequency] [Gain] [Bandwidth]
Argument details
Name
Device
FILTER
Channel
Group
Node
Name
Type
Frequency
Gain
Bandwidth
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
See Groups and Channels, page 93
1–4 (selects mic input filter)
1–15 (selects processing channel filter)
Description
Units
0 = None, 1 = All Pass, 2 = Low Pass,
3 = High Pass, 4 = Low Shelving,
5 = High Shelving, 6 = Parametric Equalizer,
7 = CD Horn, 8 = Bessel Crossover,
9 = Butterworth Crossover,
10 = Linkwitz-Riley Crossover, 11 = Notch,
Null to return the current mode
0 for Null (Type 0)
Hz
20 to 20,000 (Type 1–6, 8–11)
Hz
500 to 5,000 (Type 7)
Hz
0 for Null (Type 0–3, 7, 11)
dB
-15.00 to 15.00 (Type 4–6)
dB per octave
12, 18, 24 (Type 8–9)
dB per octave
12, 24 (Type 10)
dB per octave
-80 nonadjustable (Type 11)
0 to Null (Type 0–5, 7)
.05–5.00 (Type 6, 11)
2 = low pass, 3 = high pass (Type 8–10)
Examples
#40 FILTER 1 M 3 2 200 On PSR1212 unit 0 (#40) the filter (FILTER) for mic
(M) channel 1, node 3 is set as a low-pass filter (2) at 200Hz.
#41 FILTER B P 2 4 3000 -10 On PSR1212 unit 1 (#41) the filter (FILTER)
for processing (P) channel B, node 2, is set as a low shelving (4) filter at 3000Hz
and a gain of -10dB.
#42 FILTER 3 M 2 6 5000 -15 1.00 On PSR1212 unit 2 (#42), the filter
(FILTER) for mic (M) channel 3, node 2, is set as a PEQ (6) with a center
frequency of 5000Hz, a bandwidth of 1.00, and a gain of -15dB.
#43 FILTER B P 2 7 4000 On PSR1212 unit 3 (#43), the filter (FILTER) for
processing (P) channel B, node 2, is set as a CD Horn (7) at a frequency of
4000Hz.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
FILTSEL - Filter Select
This command turns on and off the filters on input and audio processing channels.
Command form: DEVICE FILTSEL <Channel> <Group> <Node> [Value]
Argument details
Name
Device
FILTSEL
Channel
Group
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
M = Mic Inputs, P = Processing Channels
Node
1-4, or * for all (selects mic input filter)
1-15, or * for all (selects processing channel filter)
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Value
Example: #44 FILTSEL B P 2 1 On PSR1212 unit 4 (#44), the filter
(FILTSEL) on processing (P) channel B, node 2, is set to on (1).
FLOW - Flow Control
This command selects/reports the flow control of the serial port on the unit.
Hardware flow control is implemented using DTR and DSR.
Command form: DEVICE FLOW [Value]
Argument details
Name
Device
FLOW
Value
Description
0–7 or * to select all units
Command form
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Example: #46 FLOW 1 On PSR1212 unit 6 (#46), the flow control (FLOW) to
the RS-232 port is set to on (1).
FMP - First Mic Priority Mode
This command selects/reports first Mic priority mode for a gating group.
Command form: DEVICE FMP <Channel> [Value]
Argument details
Name
Device
FMP
Channel
Description
0–7 or * to select all units
Command form
1–4, A–D (selects gating group)
Value
0 = Off, 1 = On, 2 = Toggle, Null returns the current mode
Example: #45 FMP A 1 On PSR1212 unit 5 (#45), the first mic priority mode
(FMP) for gating group A is set to on (1).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
103
104
Appendices ~ Appendix E: Serial Commands
FPP - Front Panel Passcode
This command sets and reports the current passcode setting for the unit. Each
character in the password represents a button on the front panel. See button
assignment table below. When the user is requested to unlock the front panel, they
must press the buttons in the sequence of the stored password.
Command form:
DEVICE FPP <char1><char2><char3><char4><char5>
Button assignment
Value
1
2
3
4
5
Button represented
Up arrow button
Enter button
ESC button
Down arrow button
Meter button
Argument details
Name
Device
FPP
Char 1–5
Description
0–7 or * to select all units
Command form
1–5 (see button assignments)
CLEAR will clear the passcode
Null will return current passcode
Example: #45 FPP 12345 On PSR1212 unit 5 (#45), the front panel passcode
(FPP) is set to Up Arrow (1), Enter (2), Esc (3), Down Arrow (4), Meter (5).
GAIN - Gain Adjustment
Values indicate entry
range
only.
Actual
internal range of the
gain stage is from -65 to 20.
Absolute values will be limited to
the internal gain range and
values below –65 will mute the
channel.
-
This command changes or reports back the input gain for a channel.
Command form: DEVICE GAIN <Channel> <Group> [Value A/R]
Argument details
Name
Device
GAIN
Channel
Group
Value
A/R
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
I = Inputs, O = Outputs, M = Mic Inputs,
P = Processing Channels, L = Line Inputs
-99 to 99 *, Null to return the current gain
A = Absolute, R = Relative, Null = Relative
Example: #41 GAIN 4 O 12 A On PSR1212 unit 1 (#41), the GAIN for Output
(O) 4 is set to 12dB absolute (A).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
105
Appendices ~ Appendix E: Serial Commands
GATE - Gate Status
This command reports the gate status of mics. This command is read only.
Command form: DEVICE GATE
Argument details
Name
Device
GATE
Description
0–7 or * to select all units
Command form
The command will return the gate status of mic inputs 1–8 in hexadecimal.
Example:
If
Hex # returned
Hexadecimal Description
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mic 8
Mic 7
Mic 6
Mic 5
Mic 4
Mic 3
Mic 2
Mic 1
Mics 1 and 2 are gated on
03
0
0
0
0
0
0
1
1
Mics 1 and 3 are gated on
05
0
0
0
0
0
1
0
1
Mics 1, 4, and 7 are gated on
49
0
1
0
0
1
0
0
1
Mics 3–6 and 8 are gated on
BC
1
0
1
1
1
1
0
0
First digit
GHOLD- Gate Hold Time Adjust
This command selects/reports the setting of hold time.
Command form: DEVICE GHOLD <Channel> [Value]
Argument details
Name
Device
GHOLD
Channel
Value
Description
Units
0–7 or * to select all units
Command form
See Groups and Channels, page 93
0.10-8.00
S
Null to return the current hold time
Example: #40 GHOLD 1 .3 On PSR1212 unit 0 (#40), the hold time (GHOLD)
for mic channel 1 is 300ms (.3).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Second digit
106
Appendices ~ Appendix E: Serial Commands
GMODE - Gating Mode
This command selects/reports the setting of gating mode.
Command form: DEVICE GMODE <Channel> [Value]
Argument details
Name
Device
GMODE
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (select mic input)
1 = auto, 2 = manual on, 3 = manual off, Null= current mode
Example: #45 GMODE 1 2 On PSR1212 unit 5 (#45), mic channel 1 is set to
a gating mode (GMODE) if manual on (2).
GOVER - Gating Override
This command selects/reports the setting of gating override.
Command form: DEVICE GOVER <Channel> [Value]
Argument details
Name
Device
GOVER
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = current mode
Example: #46 GOVER 1 0 On PSR1212 unit 6 (#46), the gating override
(GOVER) on mic channel 1 is set to off (0).
GRATIO - Gate Ratio Adjust
This command selects/reports the setting of the gate ratio.
Command form: DEVICE GRATIO <Channel> [Value]
Argument details
Name
Device
GRATIO
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (select mic input)
0 to 50
Null to return current ratio
Units
dB
Example: #42 GRATIO 1 15 On PSR1212 unit 2 (#42), the gate ratio
(GRATIO) for mic channel 1 is set to 15dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
107
Appendices ~ Appendix E: Serial Commands
GREPORT - Gate Report
This command selects/reports the gate status.
Command form: DEVICE GREPORT <Value>
Argument details
Name
Device
GREPORT
Value
Description
0–7 or * to select all units
Command form
0 = Off, 1 = On, 2 = Toggle
Example: #43 GREPORT 1 On PSR1212 unit 3 (#43), the gate reporting
(GREPORT) is set to on (1).
GRPSEL - Gating Group Select
This command selects/reports which gating group each input is assigned. There can
be only one selection per input.
Command form: DEVICE GRPSEL <Channel> [Value]
Argument details
Name
Device
GRPSEL
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (selects mic input)
1–4, A–D (selects gating group), Null to return current value
Example: #44 GRPSEL 1 A On PSR1212 unit 4 (#44), mic channel 1 is
assigned to gating group (GRPSEL) A.
LABEL - Label
This selects/reports the label of the specific channel identified in the unit.
Command form: DEVICE LABEL <Channel><Group>[In/Out] [String]
Argument details
Name
Device
LABEL
Channel
Group
In/Out
String
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
I, O, M, G, P, L, E, U, W, S, C (see page 93)
0 = Output, 1 = Input (For expansion bus groups only)
String of up to 20 characters representing the label text.
Null to query and CLEAR to clear the label
Example: #47 LABEL 1 M WIRELESS On PSR1212 unit 7 (#47), the label
(LABEL) for mic (M) channel 1 is WIRELESS.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Gate report sends a
report on every gate
change. If no mics are
gated on, the report will be sent
every 10 seconds.
-
108
Appendices ~ Appendix E: Serial Commands
LFP - Lock Front Panel
This command sets and reports front panel access for the unit. When the unit is
locked, access is not allowed to the unit until the unit is unlocked.
Command form: DEVICE LFP [Value]
Argument details
Name
Device
LFP
Value
Description
0–7 or * to select all units
Command form
0 = Unlock Panel, 1 = Lock Panel, 2 = Toggle Value,
3 = Lock when timed out
Example: #44 LFP 1 The PSR1212 unit 4 (#44), front panel (LFP) is locked (1).
LMO - Last Mic On Mode
This command selects/reports last Mic on mode for the specified gating group.
Command form: DEVICE LMO <Channel> [Value]
Argument details
Name
Device
LMO
Channel
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
0 = Last Mic Mode disabled
1–8 = Select Last Mic mode on specified channel
* = Last mic to stay on, Null to return the current mode
Example: #40 LMO A 0 On PSR1212 unit 0 (#40), the Last Mic Mode (LMO)
for gating group A is disabled (0).
LOCK - Preset and Macro Lock
This command selects/reports the state of the preset and macro lock. When on, the
lock prevents flagged presets and macros from being altered in any way.
Command form: DEVICE LOCK [Value][Password]
Argument details
Name
Device
LOCK
Value
Password
Description
0–7 or * to select all units
Command form
0 = Off, 1 = On, 2 = Toggle
Needs to be entered only when changing the lock. For security,
this value is not returned.
Example: #41 LOCK 1 “password” On PSR1212 unit 1 (#41), any presets or
macros that have been flagged with the LOCKPRST command will be locked (LOCK)
and password protected (1) with the macro/preset password (LOCKPWD).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
109
Appendices ~ Appendix E: Serial Commands
LOCKPRST - Apply the lock to a preset or
macro
Selects/reports whether the lock is applied to a preset/macro. If a preset/macro has
the lock applied, it can be changed only if unlocked with the password.
Command form: DEVICE LOCKPRST <Channel><Group>[Value]
Argument details
Name
Device
LOCKPRST
Channel
Group
Value
Description
0–7 or * to select all units
Command form
1–32 (Preset) or 1–255 (Macro)
S = Preset, C = Macro
0 = Off, 1 = On, 2 = Toggle, Null = Query (value is
returned only if unit is unlocked)
Example: #42 LOCKPRST 5 S 1 On PSR1212 unit 2 (#42), preset 5 (5 S)
will be protected (1) whenever the lock option is enabled.
LOCKPWD - Set preset/macro password
Selects/reports the password for the preset/macro lock. This can be changed only if
the unit is unlocked.
Command form: DEVICE LOCKPWD [Value]
Argument details
Name
Device
LOCKPWD
Value
Description
0–7 or * to select all units
Command form
1–12 characters
Null = Query (value is returned only if unit is unlocked)
Example: #43 LOCKPWD mypassword On PSR1212 unit 3 (#43), the
macro/preset password (LOCKPWD) is set to mypassword.
LVL - Level
This command reports the level. This command is read only.
Command form: DEVICE LVL <Channel> <Group> [Position] [Value]
Argument details
Name
Device
LVL
Channel
Group
Position
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
See Groups and Channels, page 93
See Meter Type Definitions, page 94
-99.99 to 99.99
Sent with Null in text, value returned
Units
dB
Example: #41 LVL 8 L I 3 The level (LVL) received from PSR1212 unit 1
(#41) for line level (L) Input 8 at the Input stage (I) is 3dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
110
Appendices ~ Appendix E: Serial Commands
LVLREPORT - Level Report
This command selects level status reporting.
Command form: DEVICE LVLREPORT <Channel> <Group> [Position] [Value]
Argument details
Name
Device
LVLREPORT
Channel
Group
Position
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
See Groups and Channels, page 93
See Meter Type Definitions, page 94
0 = Off (Delete level from list of levels to be reported)
1 =On (Add specified level to list of levels to be reported)
2 = Toggle
Example: #42 LVLREPORT 8 L I 1 On PSR1212 unit 2 (#42), the level
(LVLREPORT) of line level (L) input 8 at the input stage (I) is to be added (1) to
the report.
LVLRRATE - Level Report Rate
Sets the level report rate for the unit and activates/deactivates level repeating.
Command form: DEVICE LVLRRATE [Value]
Argument details
Name
Device
LVLRRATE
Value
Description
0–7 or * to select all units
Command form
0 = Turn off reporting but leave current list
1 = Turn off reporting and clear the list
50 to 1000 = Set Rate (1 meter every x ms)
Null to return current value
Units
ms
Example: #43 LVLRRATE 100 On PSR1212 unit 3 (#43), the level report rate
(LVLRRATE) is set to 100ms.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
111
Appendices ~ Appendix E: Serial Commands
MACRO - Macro Execution/Reporting
This command executes a specified macro or reports the last macro executed. There
are 255 macros that can be specified.
Command form: DEVICE MACRO [Value]
The response indicates
execution of the macro,
but does not indicate
that each command within the
macro was executed.
-
Argument details
Name
Device
MACRO
Value
Description
0–7 or * to select all units
Command form
1-255 Value to execute user macros
Example: #45 MACRO 1 On PSR1212 unit 5 (#45), Macro (MACRO) 1 is
run.
MASTER - Expansion Bus Master Mode
This command reports the mode of the unit. The mode can be Master or Slave.
Command form: DEVICE MASTER [Value]
Argument details
Name
Device
MASTER
Value
Description
0–7 or * to select all units
Command form
1 = Master, 2 = Slave, Null = Current mode of the unit
Example: #46 MASTER 2 On PSR1212 unit 6 (#46), the MASTER mode is
set to slave (2).
MAX - Maximum Gain Setting
This command changes or reports back the maximum gain setting for an input,
output or assignable processing block.
Command form: DEVICE MAX <Channel> <Group> [Value]
Argument details
Name
Device
MAX
Channel
Group
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
I, O, M, P, L
-65.00 to 20.00
Null to return the current setting
Units
dB
Example: #41 MAX 2 M 10 On PSR1212 unit 1 (#41), the maximum (MAX)
relative gain setting for mic (M) channel 2 is 10dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
-
This setting will affect
all relative gain
adjustments.
112
Appendices ~ Appendix E: Serial Commands
MDMODE - Modem Mode
This command enables or disables the modem mode for the unit. When the modem
mode is enabled, the modem initialization string is sent out the serial port and the
serial port now requires a password before a command is processed. After five
minutes of serial inactivity the passcode will be requested to continue serial activity.
Command form: DEVICE MDMODE [Value]
Argument details
Name
Device
MDMODE
Value
Description
0–7 or * to select all units
Command form
0 = Off, 1 = On, 2 = Toggle, Null = current modem mode state
Example: #47 MDMODE 1 On PSR1212 unit 7 (#47), the modem mode
(MDMODE) is on (1).
MIN - Minimum Gain Setting
This command changes or reports back the minimum gain setting for an input,
output or assignable processing block.
Command form: DEVICE MIN <Channel> <Group> [Value]
Argument details
Name
Device
MIN
Channel
Group
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
I, O, M, P, L
-65.00 to 20.00
Null to return the current setting
Units
dB
Example: #44 MIN 2 M -10 On PSR1212 unit 4 (#44), the minimum (MIN)
relative gain setting for mic (M) channel 2 is -10dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
MINIT - Modem Initialization String
This command sets/reports the modem initialization string of the serial port when in
modem mode.
Command form: DEVICE MINIT [String]
Argument details
Name
Device
MINIT
String
Description
0–7 or * to select all units
Command form
1-80 characters (select string characters to be sent to the modem
when the unit is initialized
CLEAR = clears the modem initialization string
Null = Current string
Example: #46 MINIT ATZ On PSR1212 unit 6 (#46), the modem initialization
string (MINIT) is ATZ.
MINMAX - Minimum and Maximum Gain
Setting
This command changes or reports back the minimum and maximum gain setting for
an input, output or assignable processing block.
Command form: DEVICE MINMAX <Channel> <Group> [Minimum] [Maximum]
Argument details
Name
Device
MINMAX
Channel
Group
Minimum
Maximum
Description
0–7 or * to select all units
Command form
See Groups and Channels
I, O, M, P, L
-65.00 to 20.00, Null to return current settings
-65.00 – 20.00
Example: #45 MINMAX 2 M -12 10 On PSR1212 unit 5 (#45), the minimum
and maximum (MINMAX) relative gain settings for mic (M) channel 2 are -12dB
and 10dB respectively.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
113
114
Appendices ~ Appendix E: Serial Commands
MLINE - Mic/Line Adjust
This command selects/reports the setting of coarse gain adjustment on the input
channels 1-8. The three settings are 0dB, 25dB, and 55dB.
Command form: DEVICE MLINE <Channel>[Value]
Argument details
Name
Device
MLINE
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (selects mic inputs)
0 = 0dB (line level), 1 = 55dB, 2 = 25dB, Null = current level
Example: #43 MLINE 1 2 On PSR1212 unit 3 (#43), the mic/line (MLINE)
setting for input 1 is 25dB (2).
MMAX - Maximum Number of Microphones
This command selects/reports the maximum number of microphones for each gating
group.
Command form: DEVICE MMAX <Channel> [Value]
Argument details
Name
Device
MMAX
Channel
Value
Description
0–7 or * to select all units
Command form
1–4, A-D (gating groups)
0 = Unlimited, 1–8 = Maximum number of mics
Null = Current maximum number of microphones
Example: #42 MMAX A 4 On the PSR1212 unit 2 (#42), the max number of
mics (MMAX) in gating group A that are allowed to gate on at any one time is 4.
Once the command is
given, the unit responds
by echoing back the
command, followed by “REENTER PASSWORD” string. The
command must then be reentered exactly as entered
previously. Then, the command
will be echoed back, followed by
an “OK,” indicating that the
password has been changed.
-
MPASS - Modem Password
This command sets the current password setting for the unit when using modem
mode. The password must be entered in twice.
Command form: DEVICE MPASS [String]
Argument details
Name
Device
MMAX
String
Description
0–7 or * to select all units
Command form
0-12 characters, CLEAR = to clear the current password
Null to report the current password
Example: #40 MPASS CLEARONE On PSR1212 unit 0 (#40), the modem
password (MPASS) is set to CLEARONE.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
115
Appendices ~ Appendix E: Serial Commands
MTRX - Matrix
This command selects/reports the matrix routing of an input to an output.
Command form:
-
DEVICE MTRX <SRC CHNL> <SRC GRP> <DEST CHNL>
SRC = source
DEST = destination
CHNL = channel
GRP = group
<DEST GRP> [Value]
Argument details
Name
Device
MTRX
SRC CHNL
SRC GRP
DEST CHNL
DEST GRP
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
I, M, P, L, E
See Groups and Channels, page 93
O, P, E
0 = Cross point off
1 = Cross point on (not valid for mic sources)
2 = Cross point toggle (not valid for mic sources)
3 = Non-gated (mic sources only)
4 = Gated (mic sources only)
Null = Current mode
Example: #47 MTRX 1 M 4 O 4 On PSR1212 unit 7 (#47), mic (M) channel 1
is routed (MTRX) as gated (4) to output (O) 4.
MTRXLVL - Matrix Attenuation Adjustment
This command selects/reports the matrix level at the cross point.
Command form:
DEVICE MTRXLVL <SRC CHNL> <SRC GRP>
< DEST CHNL> <DEST GRP> [Value] [A/R]
-
Argument details
Name
Device
MTRXLVL
SRC CHNL
SRC GRP
DEST CHNL
DEST GRP
Value
A/R
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
I, M, P, L, E
See Groups and Channels, page 93
O, P, E
-99.99 to 99.99
Null = Current mode
A = Absolute
R = Relative, Null = Relative
Values indicate entry
range
only.
Actual
internal range of the gain
stage
is
from
-60 to 0 and absolute values will
be limited to the internal gain
range. Absolute levels below -60
will mute the gain stage.
Units
dB
Example: #40 MTRXLVL 1 M 4 O -6 On PSR1212 unit 0 (#40), cross point
attenuation (MTRXLVL) at the point of mic (M) 1 and output (O) 4 is -6dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
116
Appendices ~ Appendix E: Serial Commands
MUTE - Mute
This command selects/reports the setting of mute on input, output or processing
channels.
Command form: DEVICE MUTE <Channel> <Group> [Value]
Argument details
Name
Device
MUTE
Channel
Group
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 93
I, O, M, P, L
0 = Off, 1 = On, 2 = Toggle, Null = current mode
Example: #41 MUTE 2 M 1 On PSR1212 unit 1 (#41), the mute (MUTE) for
mic (M) channel 2 is on (1).
NOM - Number of Open Microphones Mode
This command selects/reports the setting of Number of Open Microphones (NOM) on
output channels. Command form: DEVICE NOM <Channel> [Value]
Argument details
Name
Device
NOM
Channel
Value
Description
0–7 or * to select all units
Command form
1–12 (select output)
0 = Off, 1 = On, 2 = Toggle, Null = Current mode
Example: #45 NOM 2 1 On PSR1212 unit 5 (#45), the number of open
microphones (NOM) attenuation for output 2 is on (1).
OFFA - Off Attenuation Mode
This command selects/reports the off attenuation mode of input channels 1–8.
Command form: DEVICE OFFA <Channel> [Value]
Argument details
Name
Device
OFFA
Channel
Value
Description
Units
0–7 or * to select all units
Command
1–8 (select mic input)
0–60 (select off attenuation level)
dB
Null to return the current off attenuation level
Example: #46 OFFA 1 12 On PSR1212 unit 6 (#46), the off attenuation
(OFFA) for mic channel 1 is 12dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
PAA - PA Adaptive Mode
This command selects/reports PA adaptive mode for the specified mixer. There can
be only one selection per mixer.
Command form: DEVICE PAA <Channel> [Value]
Argument details
Name
Device
PAA
Channel
Value
Description
0–7 or * to select all units
Command
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = Current mode
Example: #47 PAA 1 0 On PSR1212 unit 7 (#47), the PA adaptive mode
(PAA) on mic channel 1 is disabled (0).
PP - Phantom Power
This command selects/reports the setting of phantom power.
Command form: DEVICE PP <Channel> [Value]
Argument details
Name
Device
PP
Channel
Value
Description
0–7 or * to select all units
Command
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = Current mode
Example: #41 PP 2 1 On PSR1212 unit 1 (#41), the phantom power supply
(PP) for mic channel 2 is enabled (1).
PRESET - Preset Execution/Reporting
This command selects/reports the state of a preset.
Command form: DEVICE PRESET <Channel> [Value]
Argument details
Name
Device
PRESET
Channel
Value
Description
0–7 or * to select all units
Command
1–32 (select preset)
0 =Set the preset state to off
1 = Execute the preset and set the state to on
2 = Execute the preset and set the state to off
Null = Returns the current preset state
Example: #42 PRESET 5 1 On PSR1212 unit 2 (#42), preset (PRESET) 5
will execute and set the state to on (1).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
117
118
Appendices ~ Appendix E: Serial Commands
PRGSTRING - Program String
This command sets/reports a programmed string.
Command form: DEVICE PRGSTRING <ID> [Value]
Argument details
Name
Device
PRGSTRING
ID
Value
Description
0–7 or * to select all units
Command
0 – 7 (string location)
1–80 Characters
CLEAR = Clear current value
Null = Current value
Example: #43 PRGSTRING 2 MUTE On PSR1212 unit 3 (#43), string
location 2 is programmed (PRGSTRING) with MUTE.
Supported special characters
\a = alert
\b = backspace
\f = formfeed
\n = new line
\r = carriage return
\t = horizontal tab
\v = vertical tab
\\ = backslash
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
RAMP – Ramp Gain Adjustment
This command starts/stops the gain ramp for an input, output, or assignable
processing block. There is no query for this command.
Command form: DEVICE RAMP <Channel><Group><Rate>[Target]
Argument details
Name
Device
RAMP
Channel
Group
Rate
Description
Unit
0–7 or * to select all units
Command
See Groups and Channels, page 93
I, O, M, L, P, T, R (1, 2, 3, 5, 16, 17)
-50 to 50
dB/s
If value = 0. the ramp will stop
If value < 0, the gain will ramp down
If value > 0, the gain will ramp up
-65 to 20
dB
If null in text, the ramp will use the
channel’s maximum and minimum for a target
Target
Example: #47 RAMP 5 L 6 12 On PSR1212 unit 7 (#47), the gain (RAMP)
on Line Input 5 will increase at a rate of 6dB/sec until the 12dB point is
reached.
REFSEL - PA/AEC Reference Select
This command selects/reports which output is used for each mic as a reference for
power amp adaptation mode and acoustic echo cancellation where applicable. There
can be only one selection per mixer.
Command form: DEVICE REFSEL <Channel> [Ref. Group] [Ref. Channel]
Argument details
Name
Device
REFSEL
Channel
Ref. Group
Ref. Channel
Description
0–7 or * to select all units
Command
1–8 (select mic input)
0 = Output, E = Expansion bus
1–9, O–Z (select output or E-bus channel)
Example: #40 REFSEL 1 O 8 On PSR1212 unit 7 (#40), the PA/AEC reference
REFSEL for mic channel 1 is output (O) 12.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
119
120
Appendices ~ Appendix E: Serial Commands
REFSET - Reference channel setup
This command selects/reports the output the reference channel tracks.
Command form: DEVICE REFSET <Channel> <Group>[Value]
Argument details
Name
Device
REFSET
Channel
Group
Value
Description
0–7 or * to select all units
Command
1–4 (select Virtual Reference number)
1–9 (select output channel to track)
0 = none
Example: #43 REFSET 2 4 On PSR1212 unit 3 (#43), virtual reference (2) will
track gain changes made on output channel 4.
SERECHO - Serial Echo
This command selects/reports the serial echo of the RS-232 port.
Command form: DEVICE SERECHO [Value]
Argument details
Name
Device
SERECHO
Channel
Value
Description
0–7 or * to select all units
Command
See Groups and Channels, page 93
0 = Off, 1 = On, 2 = Toggle, Null = Current state
Example: #44 SERECHO 1 On PSR1212 unit 4 (#44), the serial echo
(SERECHO) of the RS-232 port is set to on (1).
If the serial mode is
changed, the terminal
will not see a response
from the unit, nor will the unit
respond to commands until the
new status is matched by the
terminal.
-
SERMODE - Serial Mode
This command selects/reports the serial mode of the RS-232 port.
Command form: DEVICE SERMODE [Value]
Argument details
Name
Device
SERMODE
Value
Description
0–7 or * to select all units
Command
1 = Text, 2 = Binary, Null = Current mode
Example: #45 SERMODE 1 On PSR1212 unit 5 (#45), the RS-232 port serial
mode (SERMODE) is set to text (1).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
SFTYMUTE - Safety mute
Selects/reports the state of the safety mute. When on, the safety mute holds all
outputs on the selected unit in a muted state. It is used primarily for troubleshooting
G-Ware.
Command form: DEVICE SFTYMUTE [Value]
Argument details
Name
Device
SFTYMUTE
Value
Description
0–7 or * to select all units
Command
0 = Off, 1 = On, 2 = Toggle, Null = Current state
Example: #42 SFTYMUTE 1 On PSR1212 unit 2 (#42), safety mute
(SFTYMUTE) is enabled (1).
SIGGEN - Signal Generator
This command selects/reports of the signal generator activation.
Command form: DEVICE SIGGEN <Channel> <Group> [Type] [Amplitude]
[Frequency]
Argument details
Name
Device
SIGGEN
Channel
Group
Type
Amplitude
Frequency
Description
0–7 or * to select all units
Command
See Groups and Channels, page 93
I, M, L
0 = Off, 1 = Pink, 2 = White, 3 = Tone, Null = Current state
-60 to +20 amplitude in dB; NULL for type 0
20 to 20,000 frequency in Hz (needed only when using tone
generation)
Example: #46 SIGGEN 1 M 2 0 On PSR1212 unit 6 (#46), the signal generator (SIGGEN) is set to input at mic (M) channel 1 with white noise (2) at 0dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
121
122
Appendices ~ Appendix E: Serial Commands
SIGTOUT - Signal Generator Time Out
Sets the signal generator time out for the unit.
Command form: DEVICE SIGTOUT [Value]
Argument details
Name
Device
SIGGEN
Value
Description
0–7 or * to select all units
Command
0 = Off, 1–30 = Set time out minutes, Null = Current rate
Example: #47 SIGTOUT 15 On PSR1212 unit 7 (#47), the signal generator
time out (SIGTOUT) is set to 15 minutes.
STRING - String Execution
The serial command to
create a string is
PRGSTRING (Program
String). See page 118.
-
This command sends the specified string out the serial port.
Command form: DEVICE STRING [ID]
Argument details
Name
Device
STRING
ID
Description
0–7 or * to select all units
Command
0–7
Null to query last string in text
Example: #41 STRING 3 On PSR1212 unit 1 (#41), the STRING programmed
into location 3 will be sent out the RS-232 port.
TOUT - Time Out Select
This command selects/reports the inactivity time out before returning to the unit title
screen.
Command form: DEVICE TOUT [Value]
Argument details
Name
Device
TOUT
Value
Description
0–7 or * to select all units
Command
0 = Off, 1–15 (select time out in minutes)
Null = Current mode
Example: #42 TOUT 5 On PSR1212 unit 2 (#42), the front panel of the unit
will time out (TOUT) after 5 minutes.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
123
Appendices ~ Appendix E: Serial Commands
UID - Unit ID
This command reports the unit ID. This command is read only.
Command form: DEVICE UID [Value]
Argument details
Name
Device
UID
Value
Description
0–7 or * to select all units
Command
Null to return value
Units
Hexadecimal
Example: #43 UID B465F991 The unit ID number (UID) received from
PSR1212 unit 3 (#43), is B456F991.
VER - Version
This command reports the firmware version of the unit. This command is read-only.
Command form: DEVICE VER [Value]
Argument details
Name
Device
VER
Value
Description
0–7 or * to select all units
Command
Null to return value
Example: #44 VER 1.0.0 The version of the firmware (VER) programmed
into PSR1212 unit 4 (#44), is 1.0.0.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
124
Appendices ~ Appendix F: Warranty
Appendix F: Warranty
ClearOne Communications, Inc. (Manufacturer) warrants that this prod
free of defects in both materials and workmanship. For full warranty
and coverage, refer to the ClearOnewww.clearone.com
website at .
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix F: Warranty
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
125
126
Appendices ~ Appendix G: Compliance
Appendix G: Compliance
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his/her own expense.
Changes or modifications not expressly approved by ClearOne
Communications, Inc. could void the user’s authority to operate the equipment.
This equipment complies with the requirements of the EU guidelines:
89/336/EEC:
“Electromagnetic Compatibility”
73/23/EEC
“Electrical operating material for use within specific
voltage limits”
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference,
and (2) This device may not cause harmful interference that may cause undesired
operation.
Safety Information
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electrical inspection authority, or electrician, as
appropriate.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
Glossary
Adaptive Ambient This portion of the mixer monitors the varying ambient noise
level in the room and changes the threshold level at which a microphone gates on.
Ambient Level The manually-set background noise level upon which the PSR1212
bases gating protocols. Used only if the Adaptive Ambient feature isn’t used.
Ambient Noise The existing room-level noise, such as that caused by ventilation
systems, paper shuffling, and background chatter.
Amplitude Plot A plot of amplitude (-18 to 18dB) vs frequency (20Hz to 20kHz)
on a logarithmic scale.
Attack Time This signal parameter determines how quickly compression is enabled.
It is calibrated in milliseconds.
Attenuation A reduction of signal amplitude.
Audio Processor A device that modifies an audio signal in response to certain
requirements.
Audio routing The process of routing input signals (Mics 1–8, Inputs 9-12, From
E-bus, From Processing) to output destinations (Output 1–12, To E-bus, To
Processing) in the Matrix screen.
Automatic Gain Control (AGC) Automatically increases or decreases audio gain
to maintain a consistent audio level.
Automatic Gating Automatically gates microphones on or off based on input levels
and other parameters programmed into the PSR1212.
Auxiliary audio Audio that comes from line level audio sources such as video
codecs, XAP TH2s, and CD players.
Bandwidth The difference between the lower and upper 3dB end points of an audio
band. Also, the range or differences between the limiting frequencies of a continuous
frequency band.
Baud Rate The number of signal transitions per second, or the clock rate of the
serial bit stream in hertz. Given 7 or 8 bits for data plus start and stop, the
approximate ASCII character transmission rate is one-tenth the baud rate.
Chairman Override Provides gating priority for chairman override enabled
microphones within the same gating group. When a mic with chairman override
gates on, all mics which don’t have chairman override enabled and are in the same
gating group will gate off.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
127
Glossary
128
Clipping A condition in which a signal level exceeds the maximum level a circuit
can handle. This is usually caused by improper gating parameters and gain settings.
It causes distortion and typically leads to listener fatigue and accelerated failure of
loudspeaker drivers.
Compression An induced reduction in the dynamic range of part or all of an audio
signal. Compression is usually used to protect individual loudspeaker components
from the damaging effects of transients.
Compressor The compressor is part of the processing settings and allows you to
change the gain transfer characteristics of the signal path and to control the
dynamics of the signal.
Configuration mode Configuration mode is the default mode in G-Ware and is
used for system setup. It provides access to the Matrix and Flow Screens. See also
Preset mode and Macro mode.
Control bus Part of the expansion bus, the control bus passes control information
to the units. Control is not affected by master/slave settings and will continue to
function even if the units are not using the audio channels.
Constant Directivity Horn Equalizer (CD Horn EQ) Horn drivers commonly
used in arrays in arenas and auditoriums have an inherent 6dB/octave high frequency
rolloff. The PSR1212’s CD Horn EQ compensates for this characteristic.
Crossover A device that passes designated frequency segments of an audio signal to
various loudspeaker elements in a sound system.
•
Bessel A crossover using a low-pass filter design characterized by a linear
phase response. This results in a constant time delay throughout the passband.
•
Butterworth A crossover using a low-pass filter design characterized by a
maximally flat magnitude response. This results in no amplitude ripple in the
passband.
•
Linkwitz-Riley A fourth-order crossover consisting of a cascaded secondorder Butterworth low-pass filter. Offers a vast improvement over the
Butterworth crossover and is the de facto standard for professional audio
active crossovers.
Cross point The intersection between an input and an output in the routing matrix.
Cross point cells are colored according to input type.
Cross point attenuation The process of attenuating audio level at the cross point.
Audio can be attenuated from 0 to 60dB.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
Decay Rate (slow, medium, fast) Determines how fast a channel gates off after
hold time expires. Default is medium.
Default meter The input/output displayed on the front panel LED meter when a
input/output meter is not specifically selected elsewhere.
Delay A setting in the Processing window. Delay calculates the amount of signal
delay (up to 500ms) based on the distance between audio source and audience and
the temperature.
Device ID A number which identifies the unit when multiple units of the same
device type are connected in an E-bus network. Because up to eight PSR1212s can
be used in the same network, the device ID range is 0–7.
Device Type A number which identifies the type of unit. For example, a PSR1212
is device type 5.
DSP Digital signal processor.
Expansion bus Consists of two RJ-45 connectors on the rear panel of the
PSR1212. An expansion bus allows multiple PSR1212s to be networked together
using category five twisted-pair (10BaseT) cable.
Expansion bus reference One of the PA adapt reference options. The expansion
bus reference allows you to reference an output on a networked unit.
Filter A device that passes and blocks audio signals based on user-definable
requirements of the system.
•
All Pass A filter that provides only phase shift or phase delay without
appreciably changing the magnitude characteristic. The filter produces a
flat amplitude response. It is useful for matching the delay of two
processing channels with different delays.
•
High Pass A filter that passes high signal frequencies while attenuating
low frequencies. The gain or loss
•
High Shelving Provides boosting or attenuation of frequencies above a
designated frequency. The transition between the spectrum above and below
the designated frequency occurs at a fixed 6dB/octave rate. The gain or loss
above the corner frequency is adjustable to +/–15dB.
•
Low Pass A filter that passes low frequencies while attenuating high
frequencies.
•
Low Shelving Provides boosting or attenuation of frequencies below a
designated frequency. The transition between the spectrum above and below
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
129
130
Glossary
the designated frequency occurs at a fixed 6dB/octave rate. The gain or loss
below the corner frequency is adjustable to +/- 15dB.
Filter Display A group of nodes plotted on a logarithmic scale. The
PSR1212’s filter display can be accessed through the Inputs 1-8, From Processing,
or To Processing windows.
First Mic Priority Increases the audio level required to gate on additional
microphones after the first mic is on. This helps ensure that only one mic gates on
when a person speaks.
Flow control The regulation of the transmission and reception of data.
Flow Screen The Flow Screen is the main access window for G-Ware features and
unit configuration. It also shows a detailed block diagram of the audio signal—
presenting a graphical explanation of each stage in the signal path.
Gain The amount a signal is increased over a given reference, typically 0. Normally
specified in dB (decibels). On the PSR1212, gain is adjustable from -65 to 20dB
(85dB range) in .5dB increments.
Gain Structure The configuration of parameters which define gain adjustment of a
signal. The optimal input gain setting is one which provides both an adequate signalto-noise ratio and reasonable headroom.
Gate The activation and deactivation of microphones.
•
Auto The microphone will gate on according to the input level, assigned
gating parameters, and gating group.
•
Manual On The microphone will gate on unless it exceeds the NOM
requirements of the gating group.
•
Manual Off The microphone is deactivated.
Gate Ratio Specifies how much louder the microphone audio level must be above
the ambient sound level before a microphone gates on.
Gating controls The gating parameters that are assigned to a gating group:
Maximum Number of Mics, First Mic Priority, and Last Mic Mode.
Gating groups A set of gating parameters which can be applied to local
microphones (Internal 1–4) or to microphones connected to other units on the
network (Global A–D). Gating groups provide greater flexibility and control of mics.
Global gating bus Part of the expansion bus, these four mix-minus buses pass mic
status and gate parameter information such as First Mic Priority and Max NOM.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
GPIO (general purpose input/output) The Control/Status A and B ports on the
PSR1212 unit. The GPIO Builder is used to program Control/Status A pins.
G-Ware Software The PSR1212’s setup and configuration software.
Hold Time The length of time that a microphone remains on after the voice (input)
level drops below the gate ratio. This can be used to prevent the microphone from
gating off during brief pauses in speech.
Last Mic Mode Sets the last-activated mic to Last On, Mic 1-8, or Off. The Last
On setting leaves the last-activated mic gated on until another mic input gates on.
Macro A series of user-created instructions, stored within the unit, which can be
executed from an RS-232 command or contact closure.
Macro Mode The G-Ware mode that allows you to customize and execute macro
commands for a PSR1212 unit or network.
Manual Gating Provides the ability to gate a microphone on or off manually.
Matrix Mixer A mixer that allows routing of any input or combination of inputs to
an output or any combination of outputs. In the case of the PSR1212, the matrix
mixer permits level control at each cross point in the matrix.
Matrix Screen The Matrix Screen facilitates the routing of any input to any
output or combination of outputs.
Maximum Number of Mics Sets the maximum number of mics that can be gated
on simultaneously.
Microphone Activation A condition in which a microphone is gated on.
Microphone Mixing A situation in which audio from mics on different signal lines
are mixed together. All mic signals can be mixed to one signal line, any or all
outputs, or mixed into separate groups. Mic signals can also be processed together
or individually.
Microphone 1 Mode Reverts mic assignment to a designated mic when all mics
gate off.
Min/Max adjust The yellow and blue upper and lower limit arrows on gain scales
are used to create minimum and maximum gain level limits. These limits apply only
when using relative gain commands; absolute gain commands can exceed the min
and max limits. Min and max limits apply to all serially connected control devices
and prevent users from adjusting levels beyond the min/max levels provided relative
gain commands are used.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
131
132
Glossary
Mixer mode The mixer mode has two settings: master and slave. Mixer mode can
be configured from the front panel or in the Unit Properties window.
Mute A condition in which an audio signal is attenuated below the audible
threshold.
Number of Open Mics (NOM)/Constant Gain Mode Adjusts the output level
based on the number of mics gated on and routed to an output.
O–R buses These four audio buses communicate NOM count and mic mixing
parameters.
Off Attenuation The amount of level reduction a microphone is given when the
microphone is not gated on.
PA Adaptive Mode The PSR1212 recognizes how much loudspeaker audio is
picked up by the microphones and then uses this level as the new ambient level when
audio is present at the power amplifier. This prevents loudspeaker audio from gating
on a microphone, while still allowing people in the room to gate on microphones as
they speak.
PA Adapt Reference This G-Ware setting determines which output (typically for a
loudspeaker) is used as a reference for an input.
PA Adapt Reference bus This bus carries reference information, making it
possible for an input to reference an output on another linked unit.
Parametric Equalizer (PEQ) A multi-band variable equalizer with control of gain,
center frequency, and bandwidth. A properly configured PEQ enables the PSR1212
to offset loudspeaker or room acoustic deficiencies.
Passwords The PSR1212 features several passwords to protect system
configuration.
•
Front panel The front panel password prevents a user from changing settings
in the front panel LCD menus. The password can be set from the front panel or
through G-Ware.
•
Macro The macro password is created in the Unit Properties window and
makes it possible to lock certain macros. A locked macro can be run without
the password. However, a password must be entered to edit the macro.
•
Modem The modem password can be created serially using the MPASS
command or through G-Ware in the Unit Properties window. The password is
required to allow remote modem access.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
•
Preset The preset password is created in the Unit Properties window and
makes it possible to lock certain presets. A locked preset can be executed
without the password. However, a password must be entered to edit the preset.
•
Site file (File Access) The site file password is set in the Site Properties
window and will lock the site file. Users must enter the password in order to
open the site file.
Phantom Power Power supplied by the PSR1212 to power most condenser
microphones. The PSR1212 provides 24 volts of phantom power. This feature can
be switched off for devices not requiring phantom power.
Phase Plot A plot of phase angle (-180 to 180 degrees) vs frequency (20Hz to
20kHz) on a logarithmic scale.
Pink Noise An audio test signal containing all the frequencies in a given audio
spectrum, with equal energy in each octave.
Preset One of 32 configurable memories in the PSR1212. A preset can be
programmed with a variety of routing, level, gating, delay, filter, and equalizer
settings to meet specific application requirements.
Preset Mask Defines whether a contact closure activates on a low or high signal on
the rear panel of the unit.
Preset Mode Preset mode is used to create presets and is accessed from the
G-Ware toolbar.
Processing blocks There are four processing blocks or channels (A–H) in the
PSR1212 each with 15 filters, delay, and a compressor for pinpoint audio
configuration. A single input or group of inputs can be routed through a processing
block and then routed to an output or multiple outputs.
Q Quality factor. It is the ratio of the center frequency divided by the bandwidth. Q
reflects an inverse relationship to the bandwidth, and adjusts from .02:1 to 40:1 on
the PSR1212.
Ratio The amount of compression applied to the output signal compared with the
input signal as the signal exceeds the threshold level.
Release time Release is a parameter which determines how quickly compression is
released after the input signal drops below the threshold.
Reverberation A diffused acoustic energy field fed and maintained by sound
reflections from the room surfaces.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
133
134
Glossary
S–Z buses These eight buses are defaulted as auxiliary mix buses. They are used to
route auxiliary audio to and from other units on the network. These buses are also
used as mic mix buses when NOM count is not required.
Serial Command A bit description designed to execute an instruction or command.
Serial mode The serial mode determines the format in which serial commands
return text or binary. The mode defaults to Binary when G-Ware is connected and
to Text when disconnected. Contact technical support for instructions on using
Binary mode.
Signal Delay Used for:
•
Compensating for physical placement of multiple drivers in a cluster—
to
align points of acoustic origin in the same plane.
•
Ensuring matching arrival times at listeners from multiple loudspeaker
drivers.
•
Using the Haas effect to maintain localization of the source, even with a
distributed system.
Signal Generator A device for generating a reference tone for sound system
calibration purposes.
Site file A site file is a file created by G-Ware which is saved on your computer.
The site file contains all information about a particular installation including all unit
settings and properties. It also provides G-Ware with the necessary information to
communicate with the site hardware using your PC.
Site properties The Site Properties window opens when you select New Site from
the File menu or click on the New Site button on the toolbar. It allows you to enter
information about the site as well as configure the communication and security
settings.
Table View Displays the numerical values of the filter parameters for all nodes of
the active filter display.
Threshold The upper or lower level at which a signal processing mechanism begins
or terminates operation.
Unit properties The Unit Properties window opens when you add a new unit to the
site. It allows you to enter information about the unit as well as configure the
communication and security settings.
Virtual reference Virtual references are echo cancellation reference points.
Multiple signals can be included in each of the four virtual references, thus allowing
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
you to reference multiple signals without sacrificing an analog output. You can open
the Virtual Reference window from the G-Ware toolbar or from the Acoustic Echo
Cancellation window.
White Noise Acoustical noise with equal energy throughout a given frequency
range.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
135
136
Index
Index
control bus 6, 7, 128
Control Panels 6, 55, 77–80, 88–90
connecting 88
Select panel 79
Volume panel 78
Control/Status A 10, 75, 85
Control/Status B 55, 86
copy and paste 28, 31, 68, 73
cross point 29, 30–31, 54, 115, 128
Cross Point Attenuation Dial window 30
crossover 51, 83, 102
A
adaptive ambient 37, 37, 83, 97, 127
add unit 24
AGC see automatic gain control
All Pass 33, 49, 83, 102, 129
ambient level 36–37, 40, 97, 127
ambient noise 35, 127
attack time see Compressor
audio routing 29, 30–31, 53, 127
O–Z routing 30
Process A–H routing 30
Auto Sweep 66 see also Signal Generator
auto-detect 24
default meter 17, 25, 101
automatic gain control 32–33, 42, 97, 127
delay 6, 51–52, 100, 129
auxiliary audio 6, 30, 42, 127
device ID 12, 15, 25, 77, 101
device type 15, 93
Document Compare Utility 66–68
bandwidth 34, 102, 127
baud rate 15, 23, 25, 93, 98, 127
D
B
E
C
category five twisted-pair cable 11
Chairman Override 36, 93, 98, 127
Clear Matrix 30
clear password 16
clipping 41, 43, 45, 52, 128
COM port 23
command line 58, 62, 63, 75, 83
Command Strings 81
compare site 66–68
Compressor 48–49, 83, 99, 128
attack time 48, 49, 99, 127
compression meter 49
group 48
input meter 49
post compressor gain 49
ratio 49
release time 48, 49
threshold 49
connect 10, 24
sync to document 24
Sync to Unit(s) 24
constant gain 44, 132
Execute Preset 58
expansion bus 31, 111, 129
connections 9, 11
labels 46
network 6, 11
reference 37–38, 119
routing to 30
Expansion Bus In/Out 5, 11, 83
F
File Access Password 23
filter 33–35, 49–51, 102, 103, 129
First Mic Priority 40, 83, 103, 130
floppy disk 22
flow control 16, 23, 25, 83, 103, 130
Flow Screen 27
front
panel control 4, 58, 64 see also LCD
menu
front panel passcode 15
G
G-Ware 21
installation 22
Program Folder 22
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
137
Index
gain structure 41, 43, 45, 52, 130
Gate 35, 105–107, 130
activation 35
adaptive ambient 36
ambient level 36–37
auto-gate 35
chairman override 36
decay rate 37
gate ratio 36
hold time 36
manual off 35
manual on 35
off attenuation 36
PA Adaptive mode 36
Gate View 73
Gating Group 39–40, 55, 107, 130
First Mic Priority 40
Global A–D 39
Internal 1–4 39
Last Mic Mode 40
Max # of Mics 39
GFirm Firmware Utility 70
Global Gating Groups A-D buses 7
GPIO 6, 27, 55, 57, 58, 64, 75, 93, 131
G-Ware Switcher 73
H
High Pass 33, 49, 83, 102, 129
hold time 36, 105, 131
I
Inputs 1–8 32
AGC 32
filters 33
gate 35
mute 32
PA Adapt Reference 37
phantom power 33
virtual reference 38
Inputs 9–12 42
AGC 42
meters 43
mute 42
Inputs menu 17
gain 18
mute 17
L
labels 27, 29, 46, 54, 55
Last Mic On 40, 108
Latency 7
LCD menu 13–19, 25
LCD menu tree 13
LCD Programming 13
adjust a parameter 14, 15
line level 32, 42, 44, 45, 83
line level outputs 45
Low Pass 64, 49, 83, 102, 129
M
Macro Editor 26, 27, 62, 63
macro password 26, 109, 132
Macro Recorder 27, 61, 63
macros 58, 61–64, 111, 131
editing macros 63
Macro Editor 62–63
macro password 62
Macro Recorder 61
running macros 64, 111
master setting 12, 15, 111
Matrix Screen 29, 131
Message Log 28, 73
meter 4
Meter menu 16
Default Meter 17
Inputs 17
Outputs 17
Processing 17
Meter reference 19
Meter View 74
Meters 41
post gain 41
post gating 41
post processing 41
pre pain 41
Min/Max limits 40
mixer mode 9, 12, 15, 132
modem 16, 23, 26, 80, 84, 112, 113
modem access 80
password 26, 80, 114
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
138
Index
N
NOM 30, 35, 44, 45, 116, 132
non-gated 5, 29, 30, 35
Notch 34, 49, 83, 102
O
Outputs 1–12 6, 10, 18, 44–45, 83
mute 44
NOM 44
Outputs menu 18
gain 18
mute 18
O–R buses 7, 30, 132
running multiple presets 58
running presets 58
virtual reference 56
Preset mode 53
Print 28, 31, 56, 67–68, 69
matrix 31
preset 56
preview 67–68
reports 69
process meter 52
Processing A–H 47–52
compressor 48
delay 51
filters 49
frequency response 50
phase 50
P
PA Adapt Reference 7, 37–38, 119, 120, 132
buses 7
PA Adaptive Mode 36
password
front panel 15, 26
file access 23
macro password 26, 62, 109
modem 26, 114
preset password 26, 54, 109
PEQ (parametric equalizer) 34
phantom power 33
pink noise 65
pinouts 84–87
Control/Status A 85
Control/Status B 86
Line 87
RS-232 84
RS-485 87
Set 87
preset 14, 26, 27, 53–60, 133
creating presets 53, 57
executing preset 58
front panel control 58
multiple presets 58–60
Preset Configuration pane 54
preset masking 55
preset password 54
preset state 58
Remote Assignment 55
room combining 59
routing matrix 54
mute 47
propagation 7, 52
R
Ramp 119
release time 99, 133
Remote Builder 27, 55, 76–80
Remote Panel 6, 10, 55, 87, 88–89
RJ-45 jumper 11
room combining 5, 53, 59–60, 61
routing matrix 29, 30, 54
RS-232 10, 11, 12, 80–81, 84, 120
see also serial commands
RS-232 menu 15–16
Baud Rate 15, 83
Clear Password 16
Flow Control 16
Modem Mode 16
RS-485 Remote Panel A/B Port 6, 87
S
Safety Mute 28, 121
security 26
serial commands 92–123
command responses 92
command structure 92
device type and ID 93
groups and channels 93
list of 95–96
meter type 94
signal flow 27
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
139
Index
signal generator 65
site file 23, 24, 134
Site Properties 16, 23, 25, 134
Communication 23
Security 23
Use Modem 23
slave setting 12, 15, 25, 111
specifications 83
status bar 28
status lights 28
storage capacity 57, 61
Sync 24, 25, 28
System menu 14
Device ID 15
Firmware Version 15
Lock Panel 14
Run Macro 14
Select Preset 14
Set Passcode 15
Unit ID 15
system requirements 21
S–Z 7, 30, 134
U
Unit Properties 25–26
communication 25
default meter 25
device ID 25
meter refresh rate 25
preset/macro password 26
security 26
serial echo 25
serial mode 25
unit name 25
unit type 25
use modem 26
Use in preset 55, 75, 78, 79
V
Virtual Reference 38, 56, 134
W
white noise 64
X
T
XAP IR Remote 76–77
threshold see compressor
Tone 65, 66
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760